A3COM-HUAWEI-CONFIG-MAN-MIB

File: A3COM-HUAWEI-CONFIG-MAN-MIB.mib (38508 bytes)

Imported modules

A3COM-HUAWEI-OID-MIB SNMPv2-CONF SNMPv2-SMI
INET-ADDRESS-MIB SNMPv2-TC

Imported symbols

huaweiUtility OBJECT-GROUP MODULE-COMPLIANCE
NOTIFICATION-GROUP TimeTicks IpAddress
Integer32 Counter32 OBJECT-TYPE
MODULE-IDENTITY NOTIFICATION-TYPE InetAddressType
InetAddress DisplayString TruthValue
RowStatus TEXTUAL-CONVENTION

Defined Types

ConfigOperationType  
Specify operation types on configuration. Currently, following types of operation are provided: running2Startup(1): Update the saved configuration (startup) file used currently with the current configuration running in the system. This operation is equivalent to the [save] command from command line. If current startup configuration file does not exist, then the default startup configuration file is created to save the data and this becomes the current startup configuration file. startup2Running(2): Update the current configuration running in the system with the saved configuration (startup) file used currently. The commands in the file are executed as if they had been entered via the command line. If the current startup configuration file does not exist, the operation will fail with the error opFileOpenError(13). running2Net(3): Send the current configuration running in the system to the network using the specified file transfer protocol. net2Running(4): Update the current configuration running in the system with a remote file from the network using the specified file transfer protocol. The commands in the file are executed as if they had been entered via the command line. net2Startup(5): Download a remote file to the local system using the specified file transfer protocol and replace the saved configuration (startup) file used currently. If current startup configurationfile does not exist, the default startup configuration file is created to save the data and this becomes the current startup configuration file. startup2Net(6): Send the saved configuration (startup) file used currently to the network using the specified file transfer protocol. If the current startup configuration file does not exist, the operation will fail with the error opFileOpenError(13).
TEXTUAL-CONVENTION    
  INTEGER running2Startup(1), startup2Running(2), running2Net(3), net2Running(4), net2Startup(5), startup2Net(6)  

ConfigOperationStateType  
The status of the specified operation. opInProgress : Specified operation is active. opOperationSuccess : Specified operation is supported and completed successfully. opInvalidOperation : Command invalid or command/protocol/device combination unsupported. opInvalidProtocol : Invalid protocol specified. opInvalidSourceName : Invalid source file name specified. opInvalidDestName : Invalid target name specified. opInvalidServerAddress : Invalid server address specified. opDeviceBusy : Specified device is in use and locked by another process. opDeviceOpenError : Invalid device name. opDeviceError : Device read, write or erase error. opDeviceNotProgrammable : Device is read-only but a write or erase operation was specified. opDeviceFull : Device is filled to capacity. opFileOpenError : Invalid file name; file not found in partition. opFileTransferError : File transfer was unsuccessful; network failure. opFileChecksumError : File checksum in Flash failed. opNoMemory : System running low on memory. opAuthFail: Invalid user name or password. opTimeOut : File transfer was timeout. opUnknownFailure : Failure unknown. opInvalidConfigFile: Invalid configration file. opSlaveFull : Operation is fail for the slave don't have enough space. opCopyToSlaveFailure : Operation is fail when copy file to the slave.
TEXTUAL-CONVENTION    
  INTEGER opInProgress(1), opSuccess(2), opInvalidOperation(3), opInvalidProtocol(4), opInvalidSourceName(5), opInvalidDestName(6), opInvalidServerAddress(7), opDeviceBusy(8), opDeviceOpenError(9), opDeviceError(10), opDeviceNotProgrammable(11), opDeviceFull(12), opFileOpenError(13), opFileTransferError(14), opFileChecksumError(15), opNoMemory(16), opAuthFail(17), opTimeOut(18), opUnknownFailure(19), opInvalidConfigFile(20), opSlaveFull(21), opCopyToSlaveFailure(22)  

H3cCfgLogEntry  
SEQUENCE    
  h3cCfgLogIndex Integer32
  h3cCfgLogTime TimeTicks
  h3cCfgLogSrcCmd INTEGER
  h3cCfgLogSrcData INTEGER
  h3cCfgLogDesData INTEGER
  h3cCfgLogTerminalType INTEGER
  h3cCfgLogTerminalUser DisplayString
  h3cCfgLogTerminalNum Integer32
  h3cCfgLogTerminalLocation DisplayString
  h3cCfgLogCmdSrcAddress IpAddress
  h3cCfgLogVirHost DisplayString
  h3cCfgLogUserName DisplayString
  h3cCfgLogServerAddress IpAddress
  h3cCfgLogFile DisplayString
  h3cCfgLogCmdSrcAddrType InetAddressType
  h3cCfgLogCmdSrcAddrRev InetAddress
  h3cCfgLogCmdSrcAddrVPNName DisplayString
  h3cCfgLogServerAddrType InetAddressType
  h3cCfgLogServerAddrRev InetAddress
  h3cCfgLogServerAddrVPNName DisplayString

H3cCfgOperateEntry  
SEQUENCE    
  h3cCfgOperateIndex Integer32
  h3cCfgOperateType ConfigOperationType
  h3cCfgOperateProtocol INTEGER
  h3cCfgOperateFileName DisplayString
  h3cCfgOperateServerAddress IpAddress
  h3cCfgOperateUserName DisplayString
  h3cCfgOperateUserPassword DisplayString
  h3cCfgOperateEndNotificationSwitch TruthValue
  h3cCfgOperateRowStatus RowStatus
  h3cCfgOperateServerPort Integer32
  h3cCfgOperateSrvAddrType InetAddressType
  h3cCfgOperateSrvAddrRev InetAddress
  h3cCfgOperateSrvVPNName DisplayString

H3cCfgOperateResultEntry  
SEQUENCE    
  h3cCfgOperateResultIndex Integer32
  h3cCfgOperateResultOptIndex Integer32
  h3cCfgOperateResultOpType ConfigOperationType
  h3cCfgOperateState ConfigOperationStateType
  h3cCfgOperateTime TimeTicks
  h3cCfgOperateEndTime TimeTicks
  h3cCfgOperFailReason DisplayString

H3cCfgExecuteResultEntry  
SEQUENCE    
  h3cCfgExecuteResultIndex Integer32
  h3cCfgExecuteResultOptIndex Integer32
  h3cCfgExecuteResultOpType ConfigOperationType
  h3cCfgExecuteState ConfigOperationStateType
  h3cCfgExecuteTime TimeTicks
  h3cCfgExecuteEndTime TimeTicks

Defined Values

h3cConfig 1.3.6.1.4.1.43.45.1.6.10
This MIB contains objects to manage the system configuration. It contains the model used to represent configuration data that exists elsewhere in the system and in peripheral devices. There are no constraints on this MIB.
MODULE-IDENTITY    

h3cConfigManObjects 1.3.6.1.4.1.43.45.1.6.10.1
OBJECT IDENTIFIER    

h3cCfgLog 1.3.6.1.4.1.43.45.1.6.10.1.1
OBJECT IDENTIFIER    

h3cCfgRunModifiedLast 1.3.6.1.4.1.43.45.1.6.10.1.1.1
The object records the value of sysUpTime when the current configuration running in the system was last modified. The value will be changed immediately after system detects the current configuration has been changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

h3cCfgRunSavedLast 1.3.6.1.4.1.43.45.1.6.10.1.1.2
The object records the value of sysUpTime when the current configuration running in the system was last saved. If the value of the object is smaller than h3cCfgRunModifiedLast, the current configuration has been modified but not saved.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

h3cCfgStartModifiedLast 1.3.6.1.4.1.43.45.1.6.10.1.1.3
The object records the value of sysUpTime when the saved configuration used currently was last modified. It may have been modified by a save of the current configuration running in the system or other methods such as copy.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

h3cCfgLogLimitedEntries 1.3.6.1.4.1.43.45.1.6.10.1.1.4
The object shows the maximum number of rows in h3cCfgLogTable. The value supported by the system is 10.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cCfgLogDeletedEntries 1.3.6.1.4.1.43.45.1.6.10.1.1.5
The total number of rows deleted from h3cCfgLogTable.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

h3cCfgLogWantBackup 1.3.6.1.4.1.43.45.1.6.10.1.1.6
Decide whether to backup the value of objects about h3cCfgLog.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

h3cCfgLogTable 1.3.6.1.4.1.43.45.1.6.10.1.1.7
Table for logging configuration operation in device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cCfgLogEntry

h3cCfgLogEntry 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1
Information of the entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cCfgLogEntry  

h3cCfgLogIndex 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.1
Index of the table beginning from 1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cCfgLogTime 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.2
Specify the sysUpTime when the config log was generated.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

h3cCfgLogSrcCmd 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.3
Specify the source command which brought the log. Currently we provide the types of source: 1.cmdLine(1):configure log instigated by command line. 2.snmp(2):configure log instigated by snmp. 3.other(3):configure log instigated by other source unknown.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cmdLine(1), snmp(2), other(3)  

h3cCfgLogSrcData 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.4
The source of the configuration data event. erase erasing destination runningData operational data alive commandSource the command source itself startupData what the system will use next reboot local local NVRAM or flash netFtp FTP network transfer hotPlugging board is inserted or pulled out on line
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER erase(1), runningData(2), commandSource(3), startupData(4), local(5), netFtp(6), hotPlugging(7)  

h3cCfgLogDesData 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.5
The destination for the configuration data event. unknown unknown runningData operational data alive commandSource the command source itself startupData what the system will use next reboot local local NVRAM or flash netFtp FTP network transfer hotPlugging board is inserted or pulled out on line
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), runningData(2), commandSource(3), startupData(4), local(5), netFtp(6), hotPlugging(7)  

h3cCfgLogTerminalType 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.6
Specifies the terminal type. If h3cCfgLogSrcCmd is not 'cmdLine', use 'notApplicable'. The value list: notApplicable(1): no meaning at this time. unknown(2): unknown terminal type. console(3): console interface. terminal(4): generic terminal. virtual(5): virtual terminal such as telnet. auxiliary(6): auxiliary interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(1), unknown(2), console(3), terminal(4), virtual(5), auxiliary(6)  

h3cCfgLogTerminalUser 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.7
The name of logging user which is available when h3cCfgLogSrcCmd is 'cmdLine'. Other, a zero length string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

h3cCfgLogTerminalNum 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.8
Specifies the terminal number. If h3cCfgLogSrcCmd is not 'cmdLine', use '-1'
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

h3cCfgLogTerminalLocation 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.9
The location of logging user which is available when h3cCfgLogSrcCmd is 'cmdLine'. Other, a zero length string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

h3cCfgLogCmdSrcAddress 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.10
The address from which a request comes when the value of h3cCfgLogSrcCmd is 'snmp(2)'. The ip address of the remote system connected when the value of h3cCfgLogTerminalType is 'virtual'. Other, the value of 0.0.0.0. This object is replaced by for it only support IPv4.
Status: deprecated Access: read-only
OBJECT-TYPE    
  IpAddress  

h3cCfgLogVirHost 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.11
The host name of remote system connected if h3cCfgLogTerminalType has the value of 'virtual'. Other, a zero length string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

h3cCfgLogUserName 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.12
The user name used when h3cCfgLogSrcData or h3cCfgLogDesData has the value of 'netFtp'. Other, a zero length string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

h3cCfgLogServerAddress 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.13
The remote server address when h3cCfgLogSrcData or h3cCfgLogDesData has the value of 'netFtp'. Other, a value of 0.0.0.0. This object is replaced by for it only support IPv4.
Status: deprecated Access: read-only
OBJECT-TYPE    
  IpAddress  

h3cCfgLogFile 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.14
The current configuration file name when h3cCfgLogSrcData has the value of 'netFtp',and h3cCfgLogDesData has the value of 'startupData'. Other, a zero length string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

h3cCfgLogCmdSrcAddrType 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.15
The type of IP address for the h3cCfgLogCmdSrcAddrRev.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

h3cCfgLogCmdSrcAddrRev 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.16
The address from which a request comes when the value of h3cCfgLogSrcCmd is 'snmp(2)'. The ip address of the remote system connected when the value of h3cCfgLogTerminalType is 'virtual'. Other, the value of 0.0.0.0.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

h3cCfgLogCmdSrcAddrVPNName 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.17
The VPN instance of this operation uses.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

h3cCfgLogServerAddrType 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.18
The type of IP address for the h3cCfgLogServerAddrRev.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

h3cCfgLogServerAddrRev 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.19
The remote server address when h3cCfgLogSrcData or h3cCfgLogDesData has the value of 'netFtp'. Other, a value of 0.0.0.0.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

h3cCfgLogServerAddrVPNName 1.3.6.1.4.1.43.45.1.6.10.1.1.7.1.20
The VPN instance of this operation uses.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

h3cCfgOperate 1.3.6.1.4.1.43.45.1.6.10.1.2
OBJECT IDENTIFIER    

h3cCfgOperateGlobalEntryLimit 1.3.6.1.4.1.43.45.1.6.10.1.2.1
The maximum number of copy entries that may be held in h3cCfgOperateTable. A particular setting does not guarantee that much data can be held.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..10  

h3cCfgOperateEntryAgeOutTime 1.3.6.1.4.1.43.45.1.6.10.1.2.2
The number of minutes an unactive h3cCfgOperateEntry SHOULD be kept in the h3cCfgOperateTable before it is active. The object is a fator taken account of when it needs delete some rows make room in h3cCfgOperateTable.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..60  

h3cCfgOperateResultGlobalEntryLimit 1.3.6.1.4.1.43.45.1.6.10.1.2.3
The maximum number of copy entries that may be held in h3cCfgOperateResultTable. A particular setting does not guarantee that much data can be held.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..50  

h3cCfgOperateTable 1.3.6.1.4.1.43.45.1.6.10.1.2.4
A table of config-operation requests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cCfgOperateEntry

h3cCfgOperateEntry 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1
An operate request entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cCfgOperateEntry  

h3cCfgOperateIndex 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.1
The unique index value of a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cCfgOperateType 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.2
Specify the type of operation on configuration.
Status: current Access: read-create
OBJECT-TYPE    
  ConfigOperationType  

h3cCfgOperateProtocol 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.3
If the value of h3cCfgOperateType is running2Net,net2Running,net2Startup or startup2net, this node specify the protocol to be used for file transfer . The default protocol is ftp if no protocol is specified. And for other value of h3cCfgOperateType , this object may be ignored by the implementation. when clusterftp or clustertftp is selected, the h3cCfgOperateServerAddress needn't be set, the server address can be acquired automatically, the value of h3cCfgOperateServerAddress is uncertain during operation. both member switch and commander switch can use them if they support HGMP v2.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ftp(1), tftp(2), clusterftp(3), clustertftp(4)  

h3cCfgOperateFileName 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.4
When the object of h3cCfgOperateType has the value of net2Startup, net2running or running2Net,the value must be specified. The file name may include the path if applicable. If the value of h3cCfgOperateType is net2Startup or net2running, this node specify the source file name of transfers.If the value of h3cCfgOperateType is running2Net , this node specify the destination file name of transfers. When h3cCfgOperateType has the value of startup2net,the object may not be created instead of using the file name of startup configuration file.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..128)  

h3cCfgOperateServerAddress 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.5
When the operation type is running2Net,net2Running,net2Startup or startup2net , the ip address of the ftp/tftp server from/to which to download/upload must be specified. Values of 0.0.0.0 or FF.FF.FF.FF are not permitted. This object is replaced by h3cFlhOperSrvAddr for it only support IPv4.
Status: deprecated Access: read-create
OBJECT-TYPE    
  IpAddress  

h3cCfgOperateUserName 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.6
When the operation type is running2Net,net2Running,net2Startup or startup2net , the user name for the ftp server from/to which to download/upload should be specified. The object must be created if h3cCfgOperateProtocol has the value of ftp.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..40)  

h3cCfgOperateUserPassword 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.7
When the operation type is running2Net,net2Running,net2Startup or startup2net , the user password for the ftp server from/to which to download/upload should be specified. The object must be created if h3cCfgOperateProtocol has the value of ftp.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..40)  

h3cCfgOperateEndNotificationSwitch 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.8
Specifies whether or not a notification should be issued on the completion of the operation.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

h3cCfgOperateRowStatus 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.9
The status of this table entry. When the status is active all the object's value in the entry is not allowed to modified.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

h3cCfgOperateServerPort 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.10
When the operation type is running2Net, net2Running, net2Startup or startup2Net, this node is used for specifying the remote port number. If the value is 0 or not specified, the known port number will be used.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

h3cCfgOperateSrvAddrType 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.11
The type of IP address for h3cCfgOperateSrvAddrRev.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

h3cCfgOperateSrvAddrRev 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.12
When the operation type is running2Net,net2Running,net2Startup or startup2net , the ip address of the ftp/tftp server from/to which to download/upload must be specified.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

h3cCfgOperateSrvVPNName 1.3.6.1.4.1.43.45.1.6.10.1.2.4.1.13
The VPN instance of this operation uses.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

h3cCfgOperateResultTable 1.3.6.1.4.1.43.45.1.6.10.1.2.5
A table of config-operation requests result.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cCfgOperateResultEntry

h3cCfgOperateResultEntry 1.3.6.1.4.1.43.45.1.6.10.1.2.5.1
The result entries of configuration operation requests.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cCfgOperateResultEntry  

h3cCfgOperateResultIndex 1.3.6.1.4.1.43.45.1.6.10.1.2.5.1.1
The index of Table, which is an incremental integer. The maximum value of the node is 2147483647. The agent should wrap the value to 1 and flush all the existing entries when the maximum value is reached.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cCfgOperateResultOptIndex 1.3.6.1.4.1.43.45.1.6.10.1.2.5.1.2
The operation index in the h3cCfgOperateTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cCfgOperateResultOpType 1.3.6.1.4.1.43.45.1.6.10.1.2.5.1.3
The operation type in the h3cCfgOperateTable.
Status: current Access: read-only
OBJECT-TYPE    
  ConfigOperationType  

h3cCfgOperateState 1.3.6.1.4.1.43.45.1.6.10.1.2.5.1.4
The operation state type in the h3cCfgOperateTable.
Status: current Access: read-only
OBJECT-TYPE    
  ConfigOperationStateType  

h3cCfgOperateTime 1.3.6.1.4.1.43.45.1.6.10.1.2.5.1.5
Record the time taken for the operation. This object will be like a stopwatch, starting when the operation starts, and stopping when the operation completes.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

h3cCfgOperateEndTime 1.3.6.1.4.1.43.45.1.6.10.1.2.5.1.6
The value of sysUpTime when the configuration operation is finished.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

h3cCfgOperFailReason 1.3.6.1.4.1.43.45.1.6.10.1.2.5.1.7
The failure reasons of configuration operation.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

h3cCfgExecuteOperate 1.3.6.1.4.1.43.45.1.6.10.1.2.6
OBJECT IDENTIFIER    

h3cCfgExecuteOperateResultEntryLimit 1.3.6.1.4.1.43.45.1.6.10.1.2.6.1
The maximum number of ConfigOperationType entries that may be held in h3cCfgExecuteResultTable. A particular setting does not guarantee that much data can be held.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..20  

h3cCfgExecuteResultTable 1.3.6.1.4.1.43.45.1.6.10.1.2.6.2
A table of configuration execute result.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H3cCfgExecuteResultEntry

h3cCfgExecuteResultEntry 1.3.6.1.4.1.43.45.1.6.10.1.2.6.2.1
The result entries of configuration execute operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  H3cCfgExecuteResultEntry  

h3cCfgExecuteResultIndex 1.3.6.1.4.1.43.45.1.6.10.1.2.6.2.1.1
The index of Table, which is an incremental integer. The maximum value of the node is 2147483647. The agent should wrap the value to 1 and flush all the existing entries when the maximum value is reached.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cCfgExecuteResultOptIndex 1.3.6.1.4.1.43.45.1.6.10.1.2.6.2.1.2
The configuration execute operation index in the h3cCfgExecuteResultTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cCfgExecuteResultOpType 1.3.6.1.4.1.43.45.1.6.10.1.2.6.2.1.3
The operation type in the h3cCfgExecuteResultTable.
Status: current Access: read-only
OBJECT-TYPE    
  ConfigOperationType  

h3cCfgExecuteState 1.3.6.1.4.1.43.45.1.6.10.1.2.6.2.1.4
Record the status of the specified operation.
Status: current Access: read-only
OBJECT-TYPE    
  ConfigOperationStateType  

h3cCfgExecuteTime 1.3.6.1.4.1.43.45.1.6.10.1.2.6.2.1.5
Record the time of the execution starts.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

h3cCfgExecuteEndTime 1.3.6.1.4.1.43.45.1.6.10.1.2.6.2.1.6
Record the time of the execution is finished.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

h3cCfgReset 1.3.6.1.4.1.43.45.1.6.10.1.2.7
Reboot device as default configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), reset(2)  

h3cCfgFirstTrapTime 1.3.6.1.4.1.43.45.1.6.10.1.1.8
Represents the first trap time.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TimeTicks  

h3cConfigManNotifications 1.3.6.1.4.1.43.45.1.6.10.2
OBJECT IDENTIFIER    

h3cCfgManEventlog 1.3.6.1.4.1.43.45.1.6.10.2.1
The object calculates the checksum on the current config per 10 minutes and even if it is different from the saved config but if a trap has been sent with the same checksum then don't send again until the checksum is different.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

h3cCfgOperateCompletion 1.3.6.1.4.1.43.45.1.6.10.2.2
When create h3cCfgOperateTable successfully, a notification may be generated.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

h3cCfgInvalidConfigFile 1.3.6.1.4.1.43.45.1.6.10.2.3
When the configuration file is invalid, this notification will be generated.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

h3cConfigManConformance 1.3.6.1.4.1.43.45.1.6.10.3
OBJECT IDENTIFIER    

h3cConfigManCompliances 1.3.6.1.4.1.43.45.1.6.10.3.1
OBJECT IDENTIFIER    

h3cConfigManCompliance 1.3.6.1.4.1.43.45.1.6.10.3.1.1
The statement of compliance for those implementing the Huawei 3Com ConfigMan MIB.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

h3cConfigManGroups 1.3.6.1.4.1.43.45.1.6.10.3.2
OBJECT IDENTIFIER    

h3cCfgManLogGroup 1.3.6.1.4.1.43.45.1.6.10.3.2.1
A collection of objects configuration log group.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

h3cCfgOperateGroup 1.3.6.1.4.1.43.45.1.6.10.3.2.2
A group of configuration operation.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

h3cCfgManNotificationGroup 1.3.6.1.4.1.43.45.1.6.10.3.2.3
Collection of notification objects.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP