ACC-DS3

File: ACC-DS3.mib (13151 bytes)

Imported modules

Imported symbols

OBJECT-TYPE	Counter	accTrapLogSeqNum
accBRG	DisplayString	RowStatus
IfIndex	SmdsAddress

Defined Types

AccDs3InfcEntry
SEQUENCE
	accDs3InfcServiceState	INTEGER
	accDs3InfcLoopbackOp	INTEGER
	accDs3InfcLoopbackCO	INTEGER
	accDs3InfcLineLength	INTEGER
	accDs3InfcMdlProtocol	INTEGER
	accDs3InfcTxMdlEic	DisplayString
	accDs3InfcTxMdlLic	DisplayString
	accDs3InfcTxMdlFic	DisplayString
	accDs3InfcTxMdlUnit	DisplayString
	accDs3InfcTxMdlFac	DisplayString
	accDs3InfcTxMdlPort	DisplayString
	accDs3InfcTxMdlGen	DisplayString
	accDs3InfcRxMdlPathAges	Counter
	accDs3InfcRxMdlIdleAges	Counter
	accDs3InfcRxMdlTestAges	Counter
	accDs3InfcRxMdlEic	DisplayString
	accDs3InfcRxMdlLic	DisplayString
	accDs3InfcRxMdlFic	DisplayString
	accDs3InfcRxMdlUnit	DisplayString
	accDs3InfcRxMdlFac	DisplayString
	accDs3InfcRxMdlPort	DisplayString
	accDs3InfcRxMdlGen	DisplayString

Defined Values

accDs3InfcTable		1.3.6.1.4.1.5.1.1.79
The DS3 interface table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AccDs3InfcEntry

accDs3InfcEntry		1.3.6.1.4.1.5.1.1.79.1
An entry in the DS3 interface table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AccDs3InfcEntry

accDs3InfcServiceState		1.3.6.1.4.1.5.1.1.79.1.1
Indicates DS3 interface service state. Certain attributes require that the service state be in a certain state before they can be altered.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ds3InfcInService(1), ds3InfcOutOfServer(2)

accDs3InfcLoopbackOp		1.3.6.1.4.1.5.1.1.79.1.2
The local loopback mode of a DS3 interface. The entire DS3 line can be set or each individual DS1 line within the DS3 can be set separately.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	accDs3NoInfcLoop(1), accDs3PaybackLoop(2), accDs3InfcLineLoop(3), accDs3InfcEquipLoop(4), ds1loop-1(33), ds1loop-2(34), ds1loop-3(35), ds1loop-4(36), ds1loop-5(37), ds1loop-6(38), ds1loop-7(39), ds1loop-8(40), ds1loop-9(41), ds1loop-10(42), ds1loop-11(43), ds1loop-12(44), ds1loop-13(45), ds1loop-14(46), ds1loop-15(47), ds1loop-16(48), ds1loop-17(49), ds1loop-18(50), ds1loop-19(51), ds1loop-20(52), ds1loop-21(53), ds1loop-22(54), ds1loop-23(55), ds1loop-24(56), ds1loop-25(57), ds1loop-26(58), ds1loop-27(59), ds1loop-28(60)

accDs3InfcLoopbackCO		1.3.6.1.4.1.5.1.1.79.1.3
The loopback state of a DS3 interface when loopback is initiated remotely. A DS3 line can be set, or individual DS1 lines within the DS3 can be set separately.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	accDs3NoLoop(1), accDs3DS1LoopAll(19), accDs3LineLoop(27), ds1loop-1(33), ds1loop-2(34), ds1loop-3(35), ds1loop-4(36), ds1loop-5(37), ds1loop-6(38), ds1loop-7(39), ds1loop-8(40), ds1loop-9(41), ds1loop-10(42), ds1loop-11(43), ds1loop-12(44), ds1loop-13(45), ds1loop-14(46), ds1loop-15(47), ds1loop-16(48), ds1loop-17(49), ds1loop-18(50), ds1loop-19(51), ds1loop-20(52), ds1loop-21(53), ds1loop-22(54), ds1loop-23(55), ds1loop-24(56), ds1loop-25(57), ds1loop-26(58), ds1loop-27(59), ds1loop-28(60)

accDs3InfcLineLength		1.3.6.1.4.1.5.1.1.79.1.4
The approximate line length. The default is short.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ds3ShortLine(1), ds3LongLine(2)

accDs3InfcMdlProtocol		1.3.6.1.4.1.5.1.1.79.1.5
The terminal to terminal path maintenance data link protocol of the DS3 interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ds3Ansi(1), ds3NoProtocol(2)

accDs3InfcTxMdlEic		1.3.6.1.4.1.5.1.1.79.1.6
The local MDL equipment identification code for the DS3 interface. Describes the equipment.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

accDs3InfcTxMdlLic		1.3.6.1.4.1.5.1.1.79.1.7
The local MDL location identification code for the DS3 interface. Describes specific location of the equipment.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

accDs3InfcTxMdlFic		1.3.6.1.4.1.5.1.1.79.1.8
The local MDL frame identification code for the DS3 interface. Identifies where the specific piece of equipment is located in a building
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

accDs3InfcTxMdlUnit		1.3.6.1.4.1.5.1.1.79.1.9
The local MDL unit identification for the DS3 interface. It identifies where the specific piece of equipment is located within a bay.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

accDs3InfcTxMdlFac		1.3.6.1.4.1.5.1.1.79.1.10
The local MDL facility identification code for the DS3 interface. Describes a specific DS3 path.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

accDs3InfcTxMdlPort		1.3.6.1.4.1.5.1.1.79.1.11
The local MDL port identification code for the DS3 interface. Describes port on the equipment that will initiate the idle signal.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

accDs3InfcTxMdlGen		1.3.6.1.4.1.5.1.1.79.1.12
The local MDL generator number for the DS3 interface. Describes the signal generator that will initiate the test signal.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

accDs3InfcRxMdlEic		1.3.6.1.4.1.5.1.1.79.1.13
The remote MDL equipment identification code for the DS3 interface. Describes the equipment.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

accDs3InfcRxMdlLic		1.3.6.1.4.1.5.1.1.79.1.14
The remote MDL location identification code for the DS3 interface. Describes specific location of the equipment.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

accDs3InfcRxMdlFic		1.3.6.1.4.1.5.1.1.79.1.15
The remote MDL frame identification code for the DS3 interface. Identifies where the specific piece of equipment is located in a building
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

accDs3InfcRxMdlUnit		1.3.6.1.4.1.5.1.1.79.1.16
The remote MDL unit identification for the DS3 interface. It identifies where the specific piece of equipment is located within a bay.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

accDs3InfcRxMdlFac		1.3.6.1.4.1.5.1.1.79.1.17
The remote MDL unit identification for the DS3 interface. It identifies where the specific piece of equipment is located within a bay.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

accDs3InfcRxMdlPort		1.3.6.1.4.1.5.1.1.79.1.18
The remote MDL port identification code for the DS3 interface. Describes port on the equipment that will initiate the idle signal.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

accDs3InfcRxMdlGen		1.3.6.1.4.1.5.1.1.79.1.19
The remote MDL generator number for the DS3 interface. Describes the signal generator that will initiate the test signal.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

accDs3InfcRxMdlPathAges		1.3.6.1.4.1.5.1.1.79.1.20
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

accDs3InfcRxMdlIdleAges		1.3.6.1.4.1.5.1.1.79.1.21
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

accDs3InfcRxMdlTestAges		1.3.6.1.4.1.5.1.1.79.1.22
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor