ACMIB

File: ACMIB.mib (1733896 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
RFC1213-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	OBJECT-IDENTITY
NOTIFICATION-TYPE	Counter32	Integer32
IpAddress	TimeTicks	enterprises
TEXTUAL-CONVENTION	DisplayString	TimeStamp
RowStatus	DateAndTime	MODULE-COMPLIANCE
OBJECT-GROUP	ifIndex	mib-2

Defined Types

IntfIndex
A INTEGER
TEXTUAL-CONVENTION
	Integer32

ConnFailureCause
General connection failure cause
TEXTUAL-CONVENTION
	INTEGER	none(1), physical(2)

FrConnFailureCause
Frame Relay connection failure cause
TEXTUAL-CONVENTION
	INTEGER	none(1), physical(2), lmi(3), dlci(4)

AtmConnFailureCause
ATM connection failure cause
TEXTUAL-CONVENTION
	INTEGER	none(1), physical(2), oamAis(3), oamRdi(4)

ImaGrpChannelEndState
The current operational state of the Near-end or far-end IM A Group State Machine.
TEXTUAL-CONVENTION
	INTEGER	notConfigured(1), startUp(2), startUpAck(3), cfgAbtUnsupportedM(4), cfgAbtIncSymmetry(5), cfgAbtOther(6), insufficientLinks(7), blocked(8), operational(9)

TasAnnceEntry
SEQUENCE
	tasAnnceId	INTEGER
	tasAnnceType	INTEGER
	tasAnnceCmprsType	INTEGER
	tasAnnceValid	INTEGER
	tasAnnceDescription	DisplayString

TasToneConfigEntry
SEQUENCE
	tasToneId	INTEGER
	tasToneType	INTEGER
	tasToneFirstFreq	INTEGER
	tasToneSecondFreq	INTEGER
	tasToneThirdFreq	INTEGER
	tasToneOnTime	INTEGER
	tasToneOffTime	INTEGER
	tasToneLevel	INTEGER

FeatureEntry
SEQUENCE
	featureId	INTEGER
	featureStaticMem	Integer32
	featureDesiredStatus	INTEGER
	featureCurrentStatus	INTEGER

DspResourceEntry
SEQUENCE
	dspResourceId	INTEGER
	dspResourceAvail	Integer32
	dspResourceUsed	Integer32
	dspResourceUsedFailed	Integer32
	dspResourceAvailFailed	Integer32

TrapActivationEntry
SEQUENCE
	trapGroupId	INTEGER
	trapIndex	Integer32
	trapActivationStatus	INTEGER
	trapNames	DisplayString
	resetAction	INTEGER

CardEntry
SEQUENCE
	cardSlot	INTEGER
	cardType	INTEGER
	cardProtectionStatus	INTEGER
	cardOperStatus	INTEGER
	cardAdminStatus	INTEGER
	cardAlarmStatus	INTEGER
	cardCleiCode	DisplayString
	cardRevision	Integer32
	cardSerialNumber	DisplayString
	cardOperatingMode	INTEGER
	protectionConfigMode	INTEGER
	protectionStatus	INTEGER
	protectionSlot	INTEGER

TaxiPortConfigEntry
SEQUENCE
	taxiPortId	Integer32
	taxiPortType	INTEGER
	taxiLineStatus	INTEGER
	taxiOutputTransferRate	INTEGER

Ds3PortConfigEntry
SEQUENCE
	ds3PortId	Integer32
	ds3LineType	INTEGER
	ds3LineCoding	INTEGER
	ds3LoopbackConfig	INTEGER
	ds3TransmitClockSource	INTEGER
	ds3LineStatus	INTEGER
	ds3LineBuildOut	INTEGER
	ds3LineScramble	INTEGER
	ds3CellMapping	INTEGER
	ds3SendCode	INTEGER
	ds3OutputTxRate	INTEGER

MsPortConfigEntry
SEQUENCE
	msPortId	IntfIndex
	msLineCoding	INTEGER
	msBaudRate	INTEGER
	msProtocol	INTEGER
	msEquipmentType	INTEGER
	msRs232XmitMode	INTEGER
	msRs232Parity	INTEGER
	msRs232DataBits	INTEGER
	msRs232StopBits	INTEGER
	msTxDataClkSrcForDte	INTEGER
	msTxDataClkSrcForDce	INTEGER
	msRxDataClkSrcForDce	INTEGER
	msRxClkPolarity	INTEGER
	msTxClkPolarity	INTEGER
	msKgResync	INTEGER
	msHandshake	INTEGER
	msSpeedAdaption	INTEGER
	msBitStuffing	INTEGER
	msLineStatus	INTEGER
	msRxDataPolarity	INTEGER
	msTxDataPolarity	INTEGER
	msLoopbackConfig	INTEGER
	msLOSDetection	INTEGER

Ds1PortConfigEntry
SEQUENCE
	ds1PortId	Integer32
	ds1Channelization	INTEGER
	ds1LineType	INTEGER
	ds1LineCoding	INTEGER
	ds1LoopbackConfig	INTEGER
	ds1TransmitClockSource	INTEGER
	ds1LineBuildOut	INTEGER
	ds1LineStatus	INTEGER
	ds1EnhanceFeatureSet1	INTEGER
	ds1DataTransferType	INTEGER
	ds1OamInterworkingType	INTEGER
	ds1ConnGatewayFeature	INTEGER
	ds1InLineCode	INTEGER

Oc3PortConfigEntry
SEQUENCE
	oc3PortId	Integer32
	oc3LoopbackConfig	INTEGER
	oc3TransmitClockSource	INTEGER
	oc3LineStatus	INTEGER
	oc3OutputTransferRate	INTEGER
	oc3APSConfiguration	INTEGER

Oc3APSPairConfigEntry
SEQUENCE
	oc3APSPairId	Integer32
	oc3APSPairMode	INTEGER
	oc3APSPairOption	INTEGER
	oc3APSPairWorkingSFBERThreshold	INTEGER
	oc3APSPairProtectionSFBERThreshold	INTEGER
	oc3APSPairWorkingSDBERThreshold	INTEGER
	oc3APSPairProtectionSDBERThreshold	INTEGER
	oc3APSPairWTRPeriod	INTEGER
	oc3APSWorkingSlot	Integer32
	oc3APSProtectionSlot	Integer32
	oc3APSActiveSlot	Integer32
	oc3APSPairStatus	INTEGER
	oc3APSPairUserCommand	INTEGER
	oc3APSPairCurrentState	INTEGER
	oc3APSPairWorkingLineSignalStatus	INTEGER
	oc3APSPairProtectionLineSignalStatus	INTEGER

Oc3APSPairStatsEntry
SEQUENCE
	oc3APSPairStatsId	Integer32
	oc3APSPairWorkingSFDuration	Integer32
	oc3APSPairWorkingSDDuration	Integer32
	oc3APSPairProtectionSFDuration	Integer32
	oc3APSPairProtectionSDDuration	Integer32
	oc3APSPairTransmitK1K2Bytes	OCTET STRING
	oc3APSPairReceiveK1K2Bytes	OCTET STRING
	oc3APSPairSwitchOverCount	Integer32

TwoWireSourcePortConfigEntry
SEQUENCE
	twoWireSourcePortId	Integer32
	twoWireSourceLoopDetection	INTEGER
	twoWireSourceDialMode	INTEGER
	twoWireSourceLoopBackConfig	INTEGER
	twoWireSourceLineStatus	INTEGER
	twoWireSourceSignalingBits	INTEGER
	twoWireSourceRingCadence	INTEGER
	twoWireSourceSignalingState	INTEGER
	twoWireSourceTestMode	INTEGER

HighSpeedPortConfigEntry
SEQUENCE
	highSpeedPortId	Integer32
	highSpeedPortInputRate	Integer32
	highSpeedPortOutputRate	Integer32

DspPortConfigEntry
SEQUENCE
	dspPortId	Integer32

TwoWireSinkPortConfigEntry
SEQUENCE
	twoWireSinkPortId	Integer32
	twoWireSinkLoopDetection	INTEGER
	twoWireSinkDialMode	INTEGER
	twoWireSinkLineStatus	INTEGER
	twoWireSinkSignalingBits	INTEGER
	twoWireSinkSignalingState	INTEGER
	twoWireSinkTestMode	INTEGER

E3PortConfigEntry
SEQUENCE
	e3PortId	Integer32
	e3LineType	INTEGER
	e3LineCoding	INTEGER
	e3LoopbackConfig	INTEGER
	e3TransmitClockSource	INTEGER
	e3LineStatus	INTEGER
	e3LineBuildOut	INTEGER
	e3LineScramble	INTEGER
	e3CellMapping	INTEGER

E1PortConfigEntry
SEQUENCE
	e1PortId	Integer32
	e1Channelization	INTEGER
	e1LineType	INTEGER
	e1LineCoding	INTEGER
	e1LoopbackConfig	INTEGER
	e1TransmitClockSource	INTEGER
	e1LineNationalBits	INTEGER
	e1LineStatus	INTEGER
	e1TS16	INTEGER
	e1DataTransferType	INTEGER
	e1CRC4	INTEGER
	e1OamInterworkingType	INTEGER
	e1EnhanceFeatureSet1	INTEGER
	e1ConnGatewayFeature	INTEGER

EthernetPortConfigEntry
SEQUENCE
	ethernetPortId	Integer32
	ethernetLinkType	INTEGER
	ethernetPhysicalAddr	OCTET STRING
	ethernetLineStatus	INTEGER
	ethernetDuplexMode	INTEGER

Dsp2PortConfigEntry
SEQUENCE
	dsp2PortId	Integer32

ImaPortConfigEntry
SEQUENCE
	imaPortId	Integer32

Sts1PortConfigEntry
SEQUENCE
	sts1PortId	IntfIndex
	sts1LineCoding	INTEGER
	sts1LoopbackConfig	INTEGER
	sts1TransmitClockSource	INTEGER
	sts1LineBuildOut	INTEGER
	sts1LineStatus	INTEGER
	sts1StsPointers	INTEGER
	sts1VtPointers	INTEGER

TasmPortConfigEntry
SEQUENCE
	tasmPortId	Integer32

ProtectionGroupConfigEntry
SEQUENCE
	protectionSlotId	INTEGER
	workingSlotBitmap	INTEGER
	protectionCommand	INTEGER
	protectionCommandSlotId	INTEGER
	protectionGroupStatus	INTEGER
	workingSlotId	INTEGER
	workingFailedBitmap	INTEGER
	protectionActiveCounter	Integer32
	protectionOOSCounter	Integer32

TaxiChannelConfigEntry
SEQUENCE
	taxiChannelId	IntfIndex
	taxiChannelIfType	INTEGER
	taxiChannelSecuFeature	INTEGER

Ds3ChannelConfigEntry
SEQUENCE
	ds3ChannelId	IntfIndex
	ds3ChannelIfType	INTEGER
	ds3ChannelSecuFeature	INTEGER

Ds1ChannelConfigEntry
SEQUENCE
	ds1ChannelId	IntfIndex
	ds1ChannelIfType	INTEGER
	ds1ChannelDs0Map	OCTET STRING
	ds1ChannelCellMapping	INTEGER
	ds1ChannelInputCodingRule	INTEGER
	ds1ChannelSecuFeature	INTEGER
	ds1ChannelSignaling	INTEGER
	ds1ChannelCellScramble	INTEGER

MsChannelConfigEntry
SEQUENCE
	msChannelId	IntfIndex
	msChannelIfType	INTEGER
	msChannelCellBearingMode	INTEGER
	msChannelCellBearingAddrMode	INTEGER
	msChannelCellBearingPayloadFec	INTEGER
	msChannelSecuFeature	INTEGER

Oc3ChannelConfigEntry
SEQUENCE
	oc3ChannelId	IntfIndex
	oc3ChannelIfType	INTEGER
	oc3ChannelSecuFeature	INTEGER

TwoWireSourceChannelConfigEntry
SEQUENCE
	twoWireSourceChannelId	IntfIndex
	twoWireSourceChannelIfType	INTEGER
	twoWireSourceChannelConnectionType	INTEGER
	twoWireSourceChannelCompandingLaw	INTEGER
	twoWireSourceChannelSecuFeature	INTEGER
	twoWireSourceChannelVoiceCompression	INTEGER
	twoWireSourceChannelEchoCancellation	INTEGER
	twoWireSourceChannelSilenceSupression	INTEGER
	twoWireSourceChannelEncapsulationAal	INTEGER
	twoWireSourceChannelSubscriberService	INTEGER

HighSpeedChannelConfigEntry
SEQUENCE
	highSpeedChannelId	IntfIndex
	highSpeedChannelIfType	INTEGER

DspChannelConfigEntry
SEQUENCE
	dspChannelId	IntfIndex
	dspChannelIfType	INTEGER
	dspChannelInputCodingRule	INTEGER
	dspChannelVoiceCompression	INTEGER
	dspChannelEchoCancellation	INTEGER
	dspChannelSilenceSupression	INTEGER

TwoWireSinkChannelConfigEntry
SEQUENCE
	twoWireSinkChannelId	IntfIndex
	twoWireSinkChannelIfType	INTEGER
	twoWireSinkChannelConnectionType	INTEGER
	twoWireSinkChannelCompandingLaw	INTEGER
	twoWireSinkChannelVoiceCompression	INTEGER
	twoWireSinkChannelEchoCancellation	INTEGER
	twoWireSinkChannelSilenceSupression	INTEGER
	twoWireSinkChannelEncapsulationAal	INTEGER
	twoWireSinkChannelSubscriberService	INTEGER

E3ChannelConfigEntry
SEQUENCE
	e3ChannelId	IntfIndex
	e3ChannelIfType	INTEGER
	e3ChannelSecuFeature	INTEGER

E1ChannelConfigEntry
SEQUENCE
	e1ChannelId	IntfIndex
	e1ChannelIfType	INTEGER
	e1ChannelDs0Map	OCTET STRING
	e1ChannelCellMapping	INTEGER
	e1ChannelInputCodingRule	INTEGER
	e1ChannelSecuFeature	INTEGER
	e1ChannelSignaling	INTEGER

EthernetChannelConfigEntry
SEQUENCE
	ethernetChannelId	Integer32
	ethernetChannelIfType	INTEGER

Dsp2ChannelConfigEntry
SEQUENCE
	dsp2ChannelId	IntfIndex
	dsp2ChannelIfType	INTEGER
	dsp2ChannelAlarmType	INTEGER
	dsp2ChannelModeConfig	INTEGER

Dsp2AlgorithmEntry
SEQUENCE
	dsp2AlgorithmId	IntfIndex
	dsp2AlgorithmType	INTEGER

ImaGrpChannelConfigEntry
SEQUENCE
	imaGrpChannelId	IntfIndex
	imaGrpChannelIfType	INTEGER
	imaGrpChannelPortMap	Integer32
	imaGrpChannelNeState	ImaGrpChannelEndState
	imaGrpChannelFeState	ImaGrpChannelEndState
	imaGrpChannelFailureStatus	INTEGER
	imaGrpChannelSymmetry	INTEGER
	imaGrpChannelMinNumTxLinks	INTEGER
	imaGrpChannelMinNumRxLinks	INTEGER
	imaGrpChannelNeTxClkMode	INTEGER
	imaGrpChannelFeTxClkMode	INTEGER
	imaGrpChannelTxImaId	INTEGER
	imaGrpChannelRxImaId	INTEGER
	imaGrpChannelTxFrameLength	INTEGER
	imaGrpChannelRxFrameLength	INTEGER
	imaGrpChannelDiffLinkDelayMax	Integer32
	imaGrpChannelLeastDelayLink	IntfIndex
	imaGrpChannelDiffDelayMaxObs	Integer32
	imaGrpChannelAlphaValue	INTEGER
	imaGrpChannelBetaValue	INTEGER
	imaGrpChannelGammaValue	INTEGER
	imaGrpChannelStatsNeNumFailures	Integer32
	imaGrpChannelStatsFeNumFailures	Integer32
	imaGrpChannelStatsNumTxActLnks	Integer32
	imaGrpChannelStatsNumRxActLnks	Integer32
	imaGrpChannelStatsTimer	Integer32
	imaGrpChannelCompatMode	INTEGER

TasmChannelConfigEntry
SEQUENCE
	tasmChannelId	IntfIndex
	tasmChannelIfType	INTEGER
	tasmChannelAlarmType	INTEGER
	tasmChannelModeConfig	INTEGER

AtmUniConfigEntry
SEQUENCE
	atmUniIfIndex	IntfIndex
	atmUniAddrType	INTEGER
	atmUniSvcMinVpi	INTEGER
	atmUniSvcMaxVpi	INTEGER
	atmUniSvcMinVci	INTEGER
	atmUniSvcMaxVci	INTEGER
	atmUniAdminStatus	INTEGER
	atmUniOperStatus	INTEGER
	atmUniOverSubscription	INTEGER
	atmUniNwPrefix1	OCTET STRING
	atmUniT303	Integer32
	atmUniT308	Integer32
	atmUniT309	Integer32
	atmUniT310	Integer32
	atmUniT313	Integer32
	atmUniT316	Integer32
	atmUniT317	Integer32
	atmUniT322	Integer32
	atmUniT398	Integer32
	atmUniT399	Integer32
	atmUniMyNeighborIpAddress	IpAddress
	atmUniMyNeighborIfName	DisplayString
	atmUniVpiSig	INTEGER
	atmUniVciSig	INTEGER
	atmUniVpiIlmi	INTEGER
	atmUniVciIlmi	INTEGER
	atmUniAtmSignalingStatus	INTEGER
	atmUniMyIfName	DisplayString
	atmUniIlmiProtocolStatus	INTEGER
	atmUniIlmiOperStatus	INTEGER
	atmUniIlmiConfigProc	INTEGER
	atmUniIlmiConnectProc	INTEGER
	atmUniIlmiAttachPtProc	INTEGER
	atmUniIlmiSecureLinkProc	INTEGER
	atmUniIlmiAddrRegProc	INTEGER
	atmUniIlmiTimerS	Integer32
	atmUniIlmiTimerT	Integer32
	atmUniIlmiRetryK	Integer32
	atmUniIntfType	INTEGER
	atmUniUserAddress	OCTET STRING
	atmUniViSuppFlag	INTEGER
	atmUniUPCSupp	INTEGER
	atmUniUbrLoadBalSupp	INTEGER
	atmUniAvailBwIgr	Integer32
	atmUniAvailBwEgr	Integer32
	atmUniVUNISuppFlag	INTEGER
	atmUniUserAddrOrgScope	INTEGER
	atmUniSscopRxWndSz	INTEGER
	atmUniConnTrafficShapingFlag	INTEGER

AtmIispConfigEntry
SEQUENCE
	atmIispIfIndex	IntfIndex
	atmIispSvcMinVpi	INTEGER
	atmIispSvcMaxVpi	INTEGER
	atmIispSvcMinVci	INTEGER
	atmIispSvcMaxVci	INTEGER
	atmIispAdminStatus	INTEGER
	atmIispOperStatus	INTEGER
	atmIispOverSubscription	INTEGER
	atmIispT303	Integer32
	atmIispT308	Integer32
	atmIispT309	Integer32
	atmIispT310	Integer32
	atmIispT316	Integer32
	atmIispT317	Integer32
	atmIispT322	Integer32
	atmIispT398	Integer32
	atmIispT399	Integer32
	atmIispAtmSignalingStatus	INTEGER
	atmIispAvailBwIgr	Integer32
	atmIispAvailBwEgr	Integer32
	atmIispUPCSupp	INTEGER
	atmIispUbrLoadBalSupp	INTEGER
	atmIispSscopRxWndSz	INTEGER
	atmIispConnTrafficShapingFlag	INTEGER

AtmCirEmConfigEntry
SEQUENCE
	atmCirEmIfIndex	IntfIndex
	atmCirEmAdminStatus	INTEGER
	atmCirEmOperStatus	INTEGER
	atmCirEmCASIdleAbcdPattern	INTEGER
	atmCirEmCASBusyAbcdPattern	INTEGER
	atmCirEmAlarmDataPattern	INTEGER
	atmCirEmTCPattern	INTEGER
	atmCirEmDownStInterworking	INTEGER

AtmTermEmConfigEntry
SEQUENCE
	atmTermEmIfIndex	IntfIndex
	atmTermEmRxTimeOut	INTEGER
	atmTermEmAdminStatus	INTEGER
	atmTermEmOperStatus	INTEGER

HdlcConfigEntry
SEQUENCE
	hdlcIfIndex	IntfIndex
	hdlcAdminStatus	INTEGER
	hdlcOperStatus	INTEGER
	hdlcThroughPut	INTEGER
	hdlcDataInversion	INTEGER

FrUniConfigEntry
SEQUENCE
	frUniIfIndex	IntfIndex
	frUniAddrDlciLen	INTEGER
	frUniDlcmiState	INTEGER
	frUniAdminStatus	INTEGER
	frUniOperStatus	INTEGER
	frUniOverSubscription	INTEGER
	frUniLmiProtocol	INTEGER
	frUniInterworkingType	INTEGER
	frUniN391	INTEGER
	frUniN392	INTEGER
	frUniN393	INTEGER
	frUniT391	INTEGER
	frUniT392	INTEGER
	frUniAsyncLmi	INTEGER
	frLmiOperStatus	INTEGER
	frUniNT3	INTEGER
	frUniThroughPut	INTEGER

DspConfigEntry
SEQUENCE
	dspIfIndex	IntfIndex
	dspAdminStatus	INTEGER
	dspOperStatus	INTEGER

BridgeConfigEntry
SEQUENCE
	bridgeIfIndex	Integer32
	bridgeAdminStatus	INTEGER
	bridgeOperStatus	INTEGER
	bridgeNumber	INTEGER
	bridgePortPriority	INTEGER
	bridgePathCost	INTEGER
	bridgeConnectionType	INTEGER

BridgeDomainEntry
SEQUENCE
	bridgeDomainNumber	Integer32
	bridgeDomainAdminStatus	INTEGER
	bridgeDomainOperStatus	INTEGER
	bridgeDomainPriority	INTEGER
	bridgeDomainTimeSinceTopologyChange	TimeTicks
	bridgeDomainDesignatedRoot	OCTET STRING
	bridgeDomainRootCost	Integer32
	bridgeDomainRootPort	Integer32
	bridgeDomainMaxMessageAge	Integer32
	bridgeDomainHelloTime	Integer32
	bridgeDomainHoldTime	Integer32
	bridgeDomainForwardDelay	Integer32
	bridgeDomainMaxBridgeAge	INTEGER
	bridgeDomainBridgeHelloTime	INTEGER
	bridgeDomainBridgeForwardDelay	INTEGER
	bridgeDomainAgingTime	INTEGER
	bridgeDomainSpanningTree	INTEGER
	bridgeDomainTopologyChanges	Integer32
	bridgeDomainLearnedEntryDiscards	Integer32
	bridgeDomainTimer	Integer32
	bridgeDomainDefaultGateway	IpAddress
	bridgeDomainPortStatusBitmap	OCTET STRING

RouterConfigEntry
SEQUENCE
	routerIfIndex	Integer32
	routerAdminStatus	INTEGER
	routerOperStatus	INTEGER
	routerIpAddress	IpAddress
	routerIpNetworkMask	IpAddress
	routerNumber	INTEGER
	routerEthernetIpAddress	IpAddress

IsdnIntfConfigEntry
SEQUENCE
	isdnIntfId	Integer32
	isdnIntfDChanId	Integer32
	isdnIntfAdminStatus	INTEGER
	isdnIntfOperStatus	INTEGER
	isdnIntfSwitchType	INTEGER

IsdnL2ConfigEntry
SEQUENCE
	isdnL2IntfId	INTEGER
	isdnT200	INTEGER
	isdnT203	INTEGER
	isdnN200	INTEGER
	isdnN201	INTEGER
	isdnK	INTEGER
	isdnL2OperStatus	INTEGER
	isdnL2CurrentState	INTEGER

IsdnBChanConfigEntry
SEQUENCE
	isdnBChanId	INTEGER
	isdnBChanAdminStatus	INTEGER
	isdnBChanOperStatus	INTEGER

AtmDbCirEmConfigEntry
SEQUENCE
	atmDbCirEmIfIndex	IntfIndex
	atmDbCirEmAdminStatus	INTEGER
	atmDbCirEmOperStatus	INTEGER
	atmDbCirEmIdlePattern	Integer32
	atmDbCirEmServiceType	INTEGER
	atmDbCirEmDbcesType	INTEGER
	atmDbCirEmIntegrationTime	INTEGER

LmiDlciConfigEntry
SEQUENCE
	lmiDlciIfIndex	IntfIndex
	lmiDlci	Integer32
	lmiDlciOperStatus	INTEGER
	lmiDlciStatusTime	Integer32

Dsp2ConfigEntry
SEQUENCE
	dsp2IfIndex	IntfIndex
	dsp2AdminStatus	INTEGER
	dsp2OperStatus	INTEGER
	dsp2LoadCount	Integer32
	dsp2AalMode	INTEGER

AtmImaConfigEntry
SEQUENCE
	atmImaIntfIndex	IntfIndex
	atmImaNeTxState	INTEGER
	atmImaNeRxState	INTEGER
	atmImaFeTxState	INTEGER
	atmImaFeRxState	INTEGER
	atmImaNeRxDefect	INTEGER
	atmImaFeRxDefect	INTEGER
	atmImaAdminStatus	INTEGER
	atmImaOperStatus	INTEGER

AtmPnniConfigEntry
SEQUENCE
	atmPnniIfIndex	IntfIndex
	atmPnniSvcMinVpi	INTEGER
	atmPnniSvcMaxVpi	INTEGER
	atmPnniSvcMinVci	INTEGER
	atmPnniSvcMaxVci	INTEGER
	atmPnniAdminStatus	INTEGER
	atmPnniOperStatus	INTEGER
	atmPnniT303	Integer32
	atmPnniT308	Integer32
	atmPnniT309	Integer32
	atmPnniT310	Integer32
	atmPnniT313	Integer32
	atmPnniT316	Integer32
	atmPnniT317	Integer32
	atmPnniT322	Integer32
	atmPnniT397	Integer32
	atmPnniT398	Integer32
	atmPnniT399	Integer32
	atmPnniCbrServCatSupp	INTEGER
	atmPnniCbrGcacClpEqualZero	INTEGER
	atmPnniCbrMaxCellRate	Integer32
	atmPnniCbrAvailCellRate	Integer32
	atmPnniCbrCellXerDelay	Integer32
	atmPnniCbrCellLossRatioZero	Integer32
	atmPnniCbrCellLossRatioZeroPlusOne	Integer32
	atmPnniCbrCellDelayVar	Integer32
	atmPnniRtVbrServCatSupp	INTEGER
	atmPnniRtVbrGcacClpEqualZero	INTEGER
	atmPnniRtVbrMaxCellRate	Integer32
	atmPnniRtVbrAvailCellRate	Integer32
	atmPnniRtVbrCellXerDelay	Integer32
	atmPnniRtVbrCellLossRatioZero	Integer32
	atmPnniRtVbrCellLossRatioZeroPlusOne	Integer32
	atmPnniRtVbrCellDelayVar	Integer32
	atmPnniRtVbrGcacPresent	INTEGER
	atmPnniRtVbrCellRateMargin	Integer32
	atmPnniRtVbrVarianceFactor	Integer32
	atmPnniNrtVbrServCatSupp	Integer32
	atmPnniNrtVbrGcacClpEqualZero	Integer32
	atmPnniNrtVbrMaxCellRate	Integer32
	atmPnniNrtVbrAvailCellRate	Integer32
	atmPnniNrtVbrCellXerDelay	Integer32
	atmPnniNrtVbrCellLossRatioZero	Integer32
	atmPnniNrtVbrCellLossRatioZeroPlusOne	Integer32
	atmPnniNrtVbrGcacPresent	INTEGER
	atmPnniNrtVbrCellRateMargin	Integer32
	atmPnniNrtVbrVarianceFactor	Integer32
	atmPnniAbrServCatSupp	Integer32
	atmPnniAbrMaxCellRate	Integer32
	atmPnniAbrAvailCellRate	Integer32
	atmPnniUbrServCatSupp	Integer32
	atmPnniUbrMaxCellRate	Integer32
	atmPnniOverSubscription	INTEGER
	atmPnniSgnlEnabled	INTEGER
	atmPnniVpiSig	INTEGER
	atmPnniVciSig	INTEGER
	atmPnniAvailBwIgr	Integer32
	atmPnniAvailBwEgr	Integer32
	atmPnniUPCSupp	INTEGER
	atmPnniUbrLoadBalSupp	INTEGER
	atmPnniSscopRxWndSz	INTEGER
	atmPnniRemoteSvcMinVpi	INTEGER
	atmPnniRemoteSvcMaxVpi	INTEGER
	atmPnniRemoteSvcMinVci	INTEGER
	atmPnniRemoteSvcMaxVci	INTEGER
	atmPnniVpiIlmi	INTEGER
	atmPnniVciIlmi	INTEGER
	atmPnniIlmiProtocolStatus	INTEGER
	atmPnniIlmiOperStatus	INTEGER
	atmPnniIlmiConfigProc	INTEGER
	atmPnniIlmiConnectProc	INTEGER
	atmPnniIlmiAttachPtProc	INTEGER
	atmPnniIlmiSecureLinkProc	INTEGER
	atmPnniIlmiAddrRegProc	INTEGER
	atmPnniIlmiTimerS	Integer32
	atmPnniIlmiTimerT	Integer32
	atmPnniIlmiRetryK	Integer32
	atmPnniConnTrafficShapingFlag	INTEGER

AtmVnnConfigEntry
SEQUENCE
	atmVnnIfIndex	IntfIndex
	atmVnnAddrType	INTEGER
	atmVnnSvcMinVpi	INTEGER
	atmVnnSvcMaxVpi	INTEGER
	atmVnnSvcMinVci	INTEGER
	atmVnnSvcMaxVci	INTEGER
	atmVnnAdminStatus	INTEGER
	atmVnnOperStatus	INTEGER
	atmVnnOverSubscription	INTEGER
	atmVnnNwPrefix1	OCTET STRING
	atmVnnT303	Integer32
	atmVnnT308	Integer32
	atmVnnT309	Integer32
	atmVnnT310	Integer32
	atmVnnT313	Integer32
	atmVnnT316	Integer32
	atmVnnT317	Integer32
	atmVnnT322	Integer32
	atmVnnT398	Integer32
	atmVnnT399	Integer32
	atmVnnMyNeighborIpAddress	IpAddress
	atmVnnMyNeighborIfName	DisplayString
	atmVnnVpiSig	INTEGER
	atmVnnVciSig	INTEGER
	atmVnnVpiIlmi	INTEGER
	atmVnnVciIlmi	INTEGER
	atmVnnAtmSignalingStatus	INTEGER
	atmVnnMyIfName	DisplayString
	atmVnnIlmiProtocolStatus	INTEGER
	atmVnnIlmiOperStatus	INTEGER
	atmVnnIlmiConfigProc	INTEGER
	atmVnnIlmiConnectProc	INTEGER
	atmVnnIlmiAttachPtProc	INTEGER
	atmVnnIlmiSecureLinkProc	INTEGER
	atmVnnIlmiAddrRegProc	INTEGER
	atmVnnIlmiTimerS	Integer32
	atmVnnIlmiTimerT	Integer32
	atmVnnIlmiRetryK	Integer32
	atmVnnAvailBwIgr	Integer32
	atmVnnAvailBwEgr	Integer32
	atmVnnUPCSupp	INTEGER
	atmVnnUbrLoadBalSupp	INTEGER
	atmVnnSscopRxWndSz	INTEGER

VirtualIntfConfigEntry
SEQUENCE
	virtualIntfConfigIf	IntfIndex
	virtualIntfConfigVi	INTEGER
	virtualIntfConfigCellRate	Integer32
	virtualIntfConfigOverSubs	Integer32
	virtualIntfConfigRowStatus	RowStatus
	virtualIntfConfigUPCSupp	INTEGER
	virtualIntfAvailBwEgr	Integer32

VirtualUNIConfigEntry
SEQUENCE
	virtualUNIIfIndex	IntfIndex
	virtualUNIVUNIId	INTEGER
	virtualUNIVISupport	INTEGER
	virtualUNIMinVpi	INTEGER
	virtualUNIMaxVpi	INTEGER
	virtualUNIConfigRowStatus	RowStatus
	virtualUNIAddrType	INTEGER
	virtualUNISvcMinVpi	INTEGER
	virtualUNISvcMaxVpi	INTEGER
	virtualUNISvcMinVci	INTEGER
	virtualUNISvcMaxVci	INTEGER
	virtualUNIAdminStatus	INTEGER
	virtualUNIOperStatus	INTEGER
	virtualUNINwPrefix1	OCTET STRING
	virtualUNIT303	Integer32
	virtualUNIT308	Integer32
	virtualUNIT309	Integer32
	virtualUNIT310	Integer32
	virtualUNIT313	Integer32
	virtualUNIT316	Integer32
	virtualUNIT317	Integer32
	virtualUNIT322	Integer32
	virtualUNIT398	Integer32
	virtualUNIT399	Integer32
	virtualUNIMyNeighborIpAddress	IpAddress
	virtualUNIMyNeighborIfName	DisplayString
	virtualUNIVpiSig	INTEGER
	virtualUNIVciSig	INTEGER
	virtualUNISignalingAdminStatus	INTEGER
	virtualUNISignalingOperStatus	INTEGER
	virtualUNIVpiIlmi	INTEGER
	virtualUNIVciIlmi	INTEGER
	virtualUNIMyIfName	DisplayString
	virtualUNIIlmiProtocolStatus	INTEGER
	virtualUNIIlmiOperStatus	INTEGER
	virtualUNIIlmiConfigProc	INTEGER
	virtualUNIIlmiConnectProc	INTEGER
	virtualUNIIlmiAttachPtProc	INTEGER
	virtualUNIIlmiSecureLinkProc	INTEGER
	virtualUNIIlmiAddrRegProc	INTEGER
	virtualUNIIlmiTimerS	Integer32
	virtualUNIIlmiTimerT	Integer32
	virtualUNIIlmiRetryK	Integer32
	virtualUNIIntfType	INTEGER
	virtualUNIUserAddress	OCTET STRING
	virtualUNIUserAddrOrgScope	INTEGER
	virtualUNISscopRxWndSz	INTEGER

CasConfigEntry
SEQUENCE
	casIfIndex	IntfIndex
	casAdminStatus	INTEGER
	casOperStatus	INTEGER
	casProtocolType	INTEGER
	casDirection	INTEGER
	casAddressingType	INTEGER
	casBitPatternType	INTEGER
	casGroupId	INTEGER

ToneAnnceConfigEntry
SEQUENCE
	toneAnnceIfIndex	IntfIndex
	toneAnnceAdminStatus	INTEGER
	toneAnnceOperStatus	INTEGER

Gr303IntfConfigEntry
SEQUENCE
	gr303IntfId	Integer32
	gr303TMCChannelId	Integer32
	gr303EOCChannelId	Integer32
	gr303IntfAdminStatus	INTEGER
	gr303IntfOperStatus	INTEGER

Gr303Ds0ChanConfigEntry
SEQUENCE
	gr303Ds0ChanId	INTEGER
	gr303Ds0ChanAdminStatus	INTEGER
	gr303Ds0ChanOperStatus	INTEGER

Gr303IgConfigEntry
SEQUENCE
	gr303IgId	INTEGER
	gr303IgRowStatus	RowStatus
	gr303IgAdminStatus	INTEGER
	gr303IgPrimaryTMCChanIntfId	IntfIndex
	gr303IgPrimaryEOCChanIntfId	IntfIndex
	gr303IgBackupTMCChanIntfId	IntfIndex
	gr303IgBackupEOCChanIntfId	IntfIndex
	gr303IgPrimaryTMCStatus	INTEGER
	gr303IgPrimaryEOCStatus	INTEGER
	gr303IgBackupTMCStatus	INTEGER
	gr303IgBackupEOCStatus	INTEGER
	gr303IgTMCProtSwitchProvState	INTEGER
	gr303IgEOCProtSwitchProvState	INTEGER
	gr303IgTMCProtSwitchCommand	INTEGER
	gr303IgEOCProtSwitchCommand	INTEGER
	gr303IgLocalDigitalSwitchType	INTEGER
	gr303IgLocalDigitalSwitchVersion	INTEGER

Gr303IgIntfConfigEntry
SEQUENCE
	gr303IntfIgId	INTEGER
	gr303IgIntfId	INTEGER
	gr303IgIntfPhysId	INTEGER
	gr303IgIntfNetId	INTEGER
	gr303IgIntfRowStatus	RowStatus

Gr303LapdConfigEntry
SEQUENCE
	gr303LapdIgId	INTEGER
	gr303T200	Integer32
	gr303T203	Integer32
	gr303N200	Integer32
	gr303K	Integer32

Gr303TMCConfigEntry
SEQUENCE
	gr303TMCIgId	INTEGER
	gr303TMCT303	INTEGER
	gr303TMCT396	INTEGER

Gr303IgStatsEntry
SEQUENCE
	gr303IgStatsIgId	INTEGER
	gr303IgStatsCurrentInCalls	Integer32
	gr303IgStatsCurrentOutCalls	Integer32
	gr303IgStatsOutCallSuccessful	Integer32
	gr303IgStatsOutCallFailed	Integer32
	gr303IgStatsInCallSuccessful	Integer32
	gr303IgStatsInCallFailed	Integer32
	gr303IgStatsReset	INTEGER

AtmPvcVccEntry
SEQUENCE
	atmPvcVccIfA	IntfIndex
	atmPvcVccVpiA	INTEGER
	atmPvcVccVciA	INTEGER
	atmPvcVccIfB	IntfIndex
	atmPvcVccVpiB	INTEGER
	atmPvcVccVciB	INTEGER
	atmPvcVccServiceTypeA2B	INTEGER
	atmPvcVccSarTypeA2B	INTEGER
	atmPvcVccPeakCellRateA2B	Integer32
	atmPvcVccSusCellRateA2B	Integer32
	atmPvcVccMaxBurstSizeA2B	Integer32
	atmPvcVccServiceTypeB2A	INTEGER
	atmPvcVccSarTypeB2A	INTEGER
	atmPvcVccPeakCellRateB2A	Integer32
	atmPvcVccSusCellRateB2A	Integer32
	atmPvcVccMaxBurstSizeB2A	Integer32
	atmPvcVccType	INTEGER
	atmPvcVccFlow	INTEGER
	atmPvcVccRowStatus	RowStatus
	atmPvcVccFrwdErrCorrectionA2B	INTEGER
	atmPvcVccFrwdErrCorrectionB2A	INTEGER
	atmPvcVccConnectionStatus	INTEGER
	atmPvcVccOamStatus	INTEGER
	atmPvcVccDualHomed	INTEGER
	atmPvcVccViA	INTEGER
	atmPvcVccViB	INTEGER
	atmPvcVccCnfrmTypeA2B	INTEGER
	atmPvcVccCnfrmTypeB2A	INTEGER
	atmPvcVccVUNIA	INTEGER
	atmPvcVccVUNIB	INTEGER
	atmPvcVccOamStatusB	INTEGER
	atmPvcVccOAMConnEndPtStatusA	INTEGER
	atmPvcVccOAMConnEndPtStatusB	INTEGER
	atmPvcVccOAMConnSegEndPtStatusA	INTEGER
	atmPvcVccOAMConnSegEndPtStatusB	INTEGER
	atmPvcVccMfsA2B	INTEGER
	atmPvcVccMfsB2A	INTEGER
	atmPvcVccConnFailureCauseA	AtmConnFailureCause
	atmPvcVccConnFailureCauseB	AtmConnFailureCause
	atmPvcVccTrafficShapingA2B	INTEGER
	atmPvcVccTrafficShapingB2A	INTEGER

AtmPvcVpcEntry
SEQUENCE
	atmPvcVpcIfA	IntfIndex
	atmPvcVpcVpiA	INTEGER
	atmPvcVpcIfB	IntfIndex
	atmPvcVpcVpiB	INTEGER
	atmPvcVpcServiceTypeA2B	INTEGER
	atmPvcVpcSarTypeA2B	INTEGER
	atmPvcVpcPeakCellRateA2B	Integer32
	atmPvcVpcSusCellRateA2B	Integer32
	atmPvcVpcMaxBurstSizeA2B	Integer32
	atmPvcVpcServiceTypeB2A	INTEGER
	atmPvcVpcSarTypeB2A	INTEGER
	atmPvcVpcPeakCellRateB2A	Integer32
	atmPvcVpcSusCellRateB2A	Integer32
	atmPvcVpcMaxBurstSizeB2A	Integer32
	atmPvcVpcType	INTEGER
	atmPvcVpcFlow	INTEGER
	atmPvcVpcRowStatus	RowStatus
	atmPvcVpcConnectionStatus	INTEGER
	atmPvcVpcOamStatus	INTEGER
	atmPvcVpcDualHomed	INTEGER
	atmPvcVpcViA	INTEGER
	atmPvcVpcViB	INTEGER
	atmPvcVpcCnfrmTypeA2B	INTEGER
	atmPvcVpcCnfrmTypeB2A	INTEGER
	atmPvcVpcVUNIA	INTEGER
	atmPvcVpcVUNIB	INTEGER
	atmPvcVpcOamStatusB	INTEGER
	atmPvcVpcOAMConnEndPtStatusA	INTEGER
	atmPvcVpcOAMConnEndPtStatusB	INTEGER
	atmPvcVpcOAMConnSegEndPtStatusA	INTEGER
	atmPvcVpcOAMConnSegEndPtStatusB	INTEGER
	atmPvcVpcConnFailureCauseA	AtmConnFailureCause
	atmPvcVpcConnFailureCauseB	AtmConnFailureCause
	atmPvcVpcTrafficShapingA2B	INTEGER
	atmPvcVpcTrafficShapingB2A	INTEGER

AtmSvcVccEntry
SEQUENCE
	atmSvcVccIfA	IntfIndex
	atmSvcVccVpiA	INTEGER
	atmSvcVccVciA	INTEGER
	atmSvcVccIfB	IntfIndex
	atmSvcVccVpiB	INTEGER
	atmSvcVccVciB	INTEGER
	atmSvcVccServiceTypeA2B	INTEGER
	atmSvcVccSarTypeA2B	INTEGER
	atmSvcVccPeakCellRateA2B	Integer32
	atmSvcVccSusCellRateA2B	Integer32
	atmSvcVccMaxBurstSizeA2B	Integer32
	atmSvcVccServiceTypeB2A	INTEGER
	atmSvcVccSarTypeB2A	INTEGER
	atmSvcVccPeakCellRateB2A	Integer32
	atmSvcVccSusCellRateB2A	Integer32
	atmSvcVccMaxBurstSizeB2A	Integer32
	atmSvcVccFlow	INTEGER
	atmSvcVccType	INTEGER
	atmSvcVccConnectionStatus	INTEGER
	atmSvcVccViA	INTEGER
	atmSvcVccViB	INTEGER
	atmSvcVccCnfrmTypeA2B	INTEGER
	atmSvcVccCnfrmTypeB2A	INTEGER
	atmSvcVccVUNIA	INTEGER
	atmSvcVccVUNIB	INTEGER
	atmSvcVccTrafficShapingA2B	INTEGER
	atmSvcVccTrafficShapingB2A	INTEGER

IpAtmAppPvcVccEntry
SEQUENCE
	ipAtmAppPvcVccDestAddrA	IpAddress
	ipAtmAppPvcVccSubnetMaskA	IpAddress
	ipAtmAppPvcVccIfB	Integer32
	ipAtmAppPvcVccVpiB	INTEGER
	ipAtmAppPvcVccVciB	INTEGER
	ipAtmAppPvcVccServiceTypeA2B	INTEGER
	ipAtmAppPvcVccServiceTypeB2A	INTEGER
	ipAtmAppPvcVccPeakCellRateB2A	Integer32
	ipAtmAppPvcVccSusCellRateB2A	Integer32
	ipAtmAppPvcVccMaxBurstSizeB2A	Integer32
	ipAtmAppPvcVccType	INTEGER
	ipAtmAppPvcVccRowStatus	RowStatus
	ipAtmAppPvcVccConnectionStatus	INTEGER
	ipAtmAppPvcVccDualHomed	INTEGER
	ipAtmAppPvcVccViB	INTEGER
	ipAtmAppPvcVccCnfrmTypeB2A	INTEGER
	ipAtmAppPvcVccVUNIB	INTEGER
	ipAtmAppPvcVccMfsB2A	INTEGER
	ipAtmAppPvcVccConnFailureCauseB	AtmConnFailureCause
	ipAtmAppPvcVccTrafficShapingA2B	INTEGER
	ipAtmAppPvcVccOamStatus	INTEGER

IpAtmAppSvcVccEntry
SEQUENCE
	ipAtmAppSvcVccDestAddrA	IpAddress
	ipAtmAppSvcVccSubnetMaskA	IpAddress
	ipAtmAppSvcVccIfB	Integer32
	ipAtmAppSvcVccVpiB	INTEGER
	ipAtmAppSvcVccVciB	INTEGER
	ipAtmAppSvcVccServiceTypeA2B	INTEGER
	ipAtmAppSvcVccServiceTypeB2A	INTEGER
	ipAtmAppSvcVccPeakCellRateB2A	Integer32
	ipAtmAppSvcVccSusCellRateB2A	Integer32
	ipAtmAppSvcVccMaxBurstSizeB2A	Integer32
	ipAtmAppSvcVccType	INTEGER
	ipAtmAppSvcVccConnectionStatus	INTEGER
	ipAtmAppSvcVccViB	INTEGER
	ipAtmAppSvcVccCnfrmTypeB2A	INTEGER
	ipAtmAppSvcVccVUNIB	INTEGER
	ipAtmAppSvcVccTrafficShapingA2B	INTEGER

CirEmAtmPvcVccEntry
SEQUENCE
	cirEmAtmPvcVccIfA	IntfIndex
	cirEmAtmPvcVccIfB	IntfIndex
	cirEmAtmPvcVccVpiB	INTEGER
	cirEmAtmPvcVccVciB	INTEGER
	cirEmAtmPvcVccServiceType	INTEGER
	cirEmAtmPvcVccVoiceCompressionA2B	INTEGER
	cirEmAtmPvcVccSilenceDetectionA2B	INTEGER
	cirEmAtmPvcVccEchoCancellationA2B	INTEGER
	cirEmAtmPvcVccFlow	INTEGER
	cirEmAtmPvcVccRowStatus	RowStatus
	cirEmAtmPvcVccCngToneDetectionA2B	INTEGER
	cirEmAtmPvcVccCodingTranslationA2B	INTEGER
	cirEmAtmPvcVccVoiceCompressionB2A	INTEGER
	cirEmAtmPvcVccSilenceDetectionB2A	INTEGER
	cirEmAtmPvcVccEchoCancellationB2A	INTEGER
	cirEmAtmPvcVccCngToneDetectionB2A	INTEGER
	cirEmAtmPvcVccCodingTranslationB2A	INTEGER
	cirEmAtmPvcVccSarTypeB	INTEGER
	cirEmAtmPvcVccConnectionStatus	INTEGER
	cirEmAtmPvcVccDualHomed	INTEGER
	cirEmAtmPvcVccOamStatus	INTEGER
	cirEmAtmPvcVccViB	INTEGER
	cirEmAtmPvcVccCnfrmTypeB2A	INTEGER
	cirEmAtmPvcVccVUNIB	INTEGER
	cirEmAtmPvcVccAal2Cid	INTEGER
	cirEmAtmPvcVccOAMConnEndPtStatus	INTEGER
	cirEmAtmPvcVccOAMConnSegEndPtStatus	INTEGER
	cirEmAtmPvcVccConnFailureCauseA	ConnFailureCause
	cirEmAtmPvcVccConnFailureCauseB	AtmConnFailureCause
	cirEmAtmPvcVccDigitCollectTypeA2B	INTEGER
	cirEmAtmPvcVccDigitCollectTypeB2A	INTEGER
	cirEmAtmPvcVccEncodingStdA2B	INTEGER
	cirEmAtmPvcVccEncodingStdB2A	INTEGER
	cirEmAtmPvcVccEncodingProfileIdA2B	INTEGER
	cirEmAtmPvcVccEncodingProfileIdB2A	INTEGER

FrAtmPvcVccEntry
SEQUENCE
	frAtmPvcVccIfA	IntfIndex
	frAtmPvcVccDlciA	Integer32
	frAtmPvcVccIfB	IntfIndex
	frAtmPvcVccVpiB	INTEGER
	frAtmPvcVccVciB	INTEGER
	frAtmPvcVccMaxFrameSizeIn	Integer32
	frAtmPvcVccBcIn	Integer32
	frAtmPvcVccBeIn	Integer32
	frAtmPvcVccCirIn	Integer32
	frAtmPvcVccMaxFrameSizeOut	Integer32
	frAtmPvcVccBcOut	Integer32
	frAtmPvcVccBeOut	Integer32
	frAtmPvcVccCirOut	Integer32
	frAtmPvcVccServiceType	INTEGER
	frAtmPvcVccFlow	INTEGER
	frAtmPvcVccRowStatus	RowStatus
	frAtmPvcVccTimeLenIn	INTEGER
	frAtmPvcVccInterWorkingFuncIn	INTEGER
	frAtmPvcVccTimeLenOut	INTEGER
	frAtmPvcVccInterWorkingFuncOut	INTEGER
	frAtmPvcVccPeakCellRateA2B	Integer32
	frAtmPvcVccSusCellRateA2B	Integer32
	frAtmPvcVccMaxBurstSizeA2B	Integer32
	frAtmPvcVccPeakCellRateB2A	Integer32
	frAtmPvcVccSusCellRateB2A	Integer32
	frAtmPvcVccMaxBurstSizeB2A	Integer32
	frAtmPvcVccConnectionStatus	INTEGER
	frAtmPvcVccDualHomed	INTEGER
	frAtmPvcVccOamStatus	INTEGER
	frAtmPvcVccViB	INTEGER
	frAtmPvcVccCnfrmTypeB2A	INTEGER
	frAtmPvcVccVUNIB	INTEGER
	frAtmPvcVccOAMConnEndPtStatus	INTEGER
	frAtmPvcVccOAMSegEndPtStatus	INTEGER
	frAtmPvcVccMfsB2A	INTEGER
	frAtmPvcVccConnFailureCauseA	FrConnFailureCause
	frAtmPvcVccConnFailureCauseB	AtmConnFailureCause
	frAtmPvcVccTrafficShapingA2B	INTEGER

FrFrPvcEntry
SEQUENCE
	frFrPvcIfA	IntfIndex
	frFrPvcDlciA	Integer32
	frFrPvcIfB	IntfIndex
	frFrPvcDlciB	Integer32
	frFrPvcMaxFrameSizeA2B	Integer32
	frFrPvcBcA2B	Integer32
	frFrPvcBeA2B	Integer32
	frFrPvcCirA2B	Integer32
	frFrPvcMaxFrameSizeB2A	Integer32
	frFrPvcBcB2A	Integer32
	frFrPvcBeB2A	Integer32
	frFrPvcCirB2A	Integer32
	frFrPvcServiceType	INTEGER
	frFrPvcFlow	INTEGER
	frFrPvcRowStatus	RowStatus
	frFrPvcTimeLenA2B	INTEGER
	frFrPvcInterWorkingFuncA2B	INTEGER
	frFrPvcTimeLenB2A	INTEGER
	frFrPvcInterWorkingFuncB2A	INTEGER
	frFrPvcPeakCellRateA2B	Integer32
	frFrPvcSusCellRateA2B	Integer32
	frFrPvcMaxBurstSizeA2B	Integer32
	frFrPvcPeakCellRateB2A	Integer32
	frFrPvcSusCellRateB2A	Integer32
	frFrPvcMaxBurstSizeB2A	Integer32
	frFrPvcConnectionStatus	INTEGER
	frFrPvcConnFailureCauseA	FrConnFailureCause
	frFrPvcConnFailureCauseB	FrConnFailureCause

VbrAtmPvcVccEntry
SEQUENCE
	vbrAtmPvcVccIfA	IntfIndex
	vbrAtmPvcVccIfB	IntfIndex
	vbrAtmPvcVccVpiB	INTEGER
	vbrAtmPvcVccVciB	INTEGER
	vbrAtmPvcVccServiceType	INTEGER
	vbrAtmPvcVccPeakCellRateA2B	Integer32
	vbrAtmPvcVccSusCellRateA2B	Integer32
	vbrAtmPvcVccMaxBurstSizeA2B	Integer32
	vbrAtmPvcVccPeakCellRateB2A	Integer32
	vbrAtmPvcVccSusCellRateB2A	Integer32
	vbrAtmPvcVccMaxBurstSizeB2A	Integer32
	vbrAtmPvcVccFlow	INTEGER
	vbrAtmPvcVccRowStatus	RowStatus
	vbrAtmPvcVccConnectionStatus	INTEGER
	vbrAtmPvcVccDualHomed	INTEGER
	vbrAtmPvcVccOamStatus	INTEGER
	vbrAtmPvcVccViB	INTEGER
	vbrAtmPvcVccCnfrmTypeB2A	INTEGER
	vbrAtmPvcVccVUNIB	INTEGER
	vbrAtmPvcVccOAMConnEndPtStatus	INTEGER
	vbrAtmPvcVccOAMSegEndPtStatus	INTEGER
	vbrAtmPvcVccMfsB2A	INTEGER
	vbrAtmPvcVccConnFailureCauseA	ConnFailureCause
	vbrAtmPvcVccConnFailureCauseB	AtmConnFailureCause
	vbrAtmPvcVccSarTypeB	INTEGER
	vbrAtmPvcVccAal2Cid	INTEGER
	vbrAtmPvcVccTrafficShapingA2B	INTEGER

CirEmCirEmPvcEntry
SEQUENCE
	cirEmCirEmPvcIfA	IntfIndex
	cirEmCirEmPvcIfB	IntfIndex
	cirEmCirEmPvcEchoCancellationA2B	INTEGER
	cirEmCirEmPvcFlow	INTEGER
	cirEmCirEmPvcRowStatus	RowStatus
	cirEmCirEmPvcCodingTranslationA2B	INTEGER
	cirEmCirEmPvcEchoCancellationB2A	INTEGER
	cirEmCirEmPvcCodingTranslationB2A	INTEGER
	cirEmCirEmPvcConnectionStatus	INTEGER
	cirEmCirEmPvcInterworking	INTEGER
	cirEmCirEmPvcServiceType	INTEGER
	cirEmCirEmPvcConnFailureCauseA	ConnFailureCause
	cirEmCirEmPvcConnFailureCauseB	ConnFailureCause

VbrVbrPvcEntry
SEQUENCE
	vbrVbrPvcIfA	IntfIndex
	vbrVbrPvcIfB	IntfIndex
	vbrVbrPvcPeakCellRateA2B	Integer32
	vbrVbrPvcSusCellRateA2B	Integer32
	vbrVbrPvcMaxBurstSizeA2B	Integer32
	vbrVbrPvcPeakCellRateB2A	Integer32
	vbrVbrPvcSusCellRateB2A	Integer32
	vbrVbrPvcMaxBurstSizeB2A	Integer32
	vbrVbrPvcFlow	INTEGER
	vbrVbrPvcRowStatus	RowStatus
	vbrVbrPvcConnectionStatus	INTEGER
	vbrVbrPvcServiceType	INTEGER
	vbrVbrPvcConnFailureCauseA	ConnFailureCause
	vbrVbrPvcConnFailureCauseB	ConnFailureCause

BridgeBridgePvcEntry
SEQUENCE
	bridgeBridgePvcIfA	Integer32
	bridgeBridgePvcIfB	Integer32
	bridgeBridgePvcRowStatus	RowStatus
	bridgeBridgePvcConnectionStatus	INTEGER
	bridgeBridgePvcConnFailureCauseA	ConnFailureCause
	bridgeBridgePvcConnFailureCauseB	ConnFailureCause

BridgeAtmPvcVccEntry
SEQUENCE
	bridgeAtmPvcVccIfA	Integer32
	bridgeAtmPvcVccIfB	Integer32
	bridgeAtmPvcVccVpiB	INTEGER
	bridgeAtmPvcVccVciB	INTEGER
	bridgeAtmPvcVccServiceType	INTEGER
	bridgeAtmPvcVccPeakCellRateB2A	Integer32
	bridgeAtmPvcVccSusCellRateB2A	Integer32
	bridgeAtmPvcVccMaxBurstSizeB2A	Integer32
	bridgeAtmPvcVccRowStatus	RowStatus
	bridgeAtmPvcVccConnectionStatus	INTEGER
	bridgeAtmPvcVccDualHomed	INTEGER
	bridgeAtmPvcVccViB	INTEGER
	bridgeAtmPvcVccCnfrmTypeB2A	INTEGER
	bridgeAtmPvcVccVUNIB	INTEGER
	bridgeAtmPvcVccMfsB2A	INTEGER
	bridgeAtmPvcVccConnFailureCauseA	ConnFailureCause
	bridgeAtmPvcVccConnFailureCauseB	AtmConnFailureCause
	bridgeAtmPvcVccOamStatus	INTEGER
	bridgeAtmPvcVccTrafficShapingA2B	INTEGER

CirEmAtmBkPvcVccEntry
SEQUENCE
	cirEmAtmBkPvcVccIfB	IntfIndex
	cirEmAtmBkPvcVccVpiB	INTEGER
	cirEmAtmBkPvcVccVciB	INTEGER
	cirEmAtmBkPvcVccActivePvc	INTEGER
	cirEmAtmBkPvcVccAutoSwitch	INTEGER
	cirEmAtmBkPvcVccRowStatus	RowStatus
	cirEmAtmBkPvcVccViB	INTEGER
	cirEmAtmBkPvcVccVUNIB	INTEGER
	cirEmAtmBkPvcVccConnFailureCauseB	AtmConnFailureCause

VbrAtmBkPvcVccEntry
SEQUENCE
	vbrAtmBkPvcVccIfB	IntfIndex
	vbrAtmBkPvcVccVpiB	INTEGER
	vbrAtmBkPvcVccVciB	INTEGER
	vbrAtmBkPvcVccActivePvc	INTEGER
	vbrAtmBkPvcVccAutoSwitch	INTEGER
	vbrAtmBkPvcVccRowStatus	RowStatus
	vbrAtmBkPvcVccViB	INTEGER
	vbrAtmBkPvcVccVUNIB	INTEGER
	vbrAtmBkPvcVccConnFailureCauseB	AtmConnFailureCause

AtmSpvcVccAddrEntry
SEQUENCE
	atmSpvcVccIfA	IntfIndex
	atmSpvcVccAtmPortAddr	OCTET STRING
	atmSpvcVccAddrRowStatus	RowStatus

AtmSpvcVccEntry
SEQUENCE
	atmSpvcVccVpiA	INTEGER
	atmSpvcVccVciA	INTEGER
	atmSpvcVccIfB	IntfIndex
	atmSpvcVccVpiB	INTEGER
	atmSpvcVccVciB	INTEGER
	atmSpvcVccServiceTypeA2B	INTEGER
	atmSpvcVccSarTypeA2B	INTEGER
	atmSpvcVccPeakCellRateA2B	Integer32
	atmSpvcVccSusCellRateA2B	Integer32
	atmSpvcVccMaxBurstSizeA2B	Integer32
	atmSpvcVccFrwdErrCorrectionA2B	INTEGER
	atmSpvcVccServiceTypeB2A	INTEGER
	atmSpvcVccSarTypeB2A	INTEGER
	atmSpvcVccPeakCellRateB2A	Integer32
	atmSpvcVccSusCellRateB2A	Integer32
	atmSpvcVccMaxBurstSizeB2A	Integer32
	atmSpvcVccFrwdErrCorrectionB2A	INTEGER
	atmSpvcVccFlow	INTEGER
	atmSpvcVccType	INTEGER
	atmSpvcVccConnType	INTEGER
	atmSpvcVccLeafReference	INTEGER
	atmSpvcVccOperStatus	INTEGER
	atmSpvcVccRowStatus	RowStatus
	atmSpvcVccViA	INTEGER
	atmSpvcVccViB	INTEGER
	atmSpvcVccTrafficShapingA2B	INTEGER
	atmSpvcVccTrafficShapingB2A	INTEGER

AtmSpvcVccActiveSvcEntry
SEQUENCE
	atmSpvcVccRemoteAtmPortAddr	OCTET STRING
	atmSpvcVccRemoteSelectType	INTEGER
	atmSpvcVccRemoteVpi	INTEGER
	atmSpvcVccRemoteVci	INTEGER
	atmSpvcVccRetryInterval	INTEGER
	atmSpvcVccRetryLimit	INTEGER
	atmSpvcVccRestart	INTEGER
	atmSpvcVccRetryFailure	Integer32
	atmSpvcVccReleaseCause	INTEGER
	atmSpvcVccReleaseDiag	OCTET STRING

CirEmAtmSpvcVccEntry
SEQUENCE
	cirEmAtmSpvcVccIfA	IntfIndex
	cirEmAtmSpvcVccIfB	IntfIndex
	cirEmAtmSpvcVccVpiB	INTEGER
	cirEmAtmSpvcVccVciB	INTEGER
	cirEmAtmSpvcVccVoiceCompressionA2B	INTEGER
	cirEmAtmSpvcVccSilenceDetectionA2B	INTEGER
	cirEmAtmSpvcVccEchoCancellationA2B	INTEGER
	cirEmAtmSpvcVccCngToneDetectionA2B	INTEGER
	cirEmAtmSpvcVccCodingTranslationA2B	INTEGER
	cirEmAtmSpvcVccVoiceCompressionB2A	INTEGER
	cirEmAtmSpvcVccSilenceDetectionB2A	INTEGER
	cirEmAtmSpvcVccEchoCancellationB2A	INTEGER
	cirEmAtmSpvcVccCngToneDetectionB2A	INTEGER
	cirEmAtmSpvcVccCodingTranslationB2A	INTEGER
	cirEmAtmSpvcVccFlow	INTEGER
	cirEmAtmSpvcVccServiceType	INTEGER
	cirEmAtmSpvcVccConnType	INTEGER
	cirEmAtmSpvcVccCePortAddr	OCTET STRING
	cirEmAtmSpvcVccOperStatus	INTEGER
	cirEmAtmSpvcVccRowStatus	RowStatus
	cirEmAtmSpvcVccViB	INTEGER

CirEmAtmSpvcVccActiveSvcEntry
SEQUENCE
	cirEmAtmSpvcVccRemoteCePortAddr	OCTET STRING
	cirEmAtmSpvcVccRetryInterval	INTEGER
	cirEmAtmSpvcVccRetryLimit	INTEGER
	cirEmAtmSpvcVccRestart	INTEGER
	cirEmAtmSpvcVccRetryFailure	Integer32
	cirEmAtmSpvcVccReleaseCause	INTEGER
	cirEmAtmSpvcVccReleaseDiag	OCTET STRING

VbrAtmSpvcVccEntry
SEQUENCE
	vbrAtmSpvcVccIfA	IntfIndex
	vbrAtmSpvcVccIfB	IntfIndex
	vbrAtmSpvcVccVpiB	INTEGER
	vbrAtmSpvcVccVciB	INTEGER
	vbrAtmSpvcVccServiceType	INTEGER
	vbrAtmSpvcVccPeakCellRateA2B	Integer32
	vbrAtmSpvcVccSusCellRateA2B	Integer32
	vbrAtmSpvcVccMaxBurstSizeA2B	Integer32
	vbrAtmSpvcVccPeakCellRateB2A	Integer32
	vbrAtmSpvcVccSusCellRateB2A	Integer32
	vbrAtmSpvcVccMaxBurstSizeB2A	Integer32
	vbrAtmSpvcVccFlow	INTEGER
	vbrAtmSpvcVccConnType	INTEGER
	vbrAtmSpvcVccVbrPortAddr	OCTET STRING
	vbrAtmSpvcVccOperStatus	INTEGER
	vbrAtmSpvcVccRowStatus	RowStatus
	vbrAtmSpvcVccViB	INTEGER
	vbrAtmSpvcVccTrafficShapingA2B	INTEGER

VbrAtmSpvcVccActiveSvcEntry
SEQUENCE
	vbrAtmSpvcVccRemoteVbrPortAddr	OCTET STRING
	vbrAtmSpvcVccRetryInterval	INTEGER
	vbrAtmSpvcVccRetryLimit	INTEGER
	vbrAtmSpvcVccRestart	INTEGER
	vbrAtmSpvcVccRetryFailure	Integer32
	vbrAtmSpvcVccReleaseCause	INTEGER
	vbrAtmSpvcVccReleaseDiag	OCTET STRING

AtmSpvcVccRlsEntry
SEQUENCE
	atmSpvcVccRelease	INTEGER

CirEmAtmSpvcVccRlsEntry
SEQUENCE
	cirEmAtmSpvcVccRelease	INTEGER

VbrAtmSpvcVccRlsEntry
SEQUENCE
	vbrAtmSpvcVccRelease	INTEGER

FrAtmBkPvcVccEntry
SEQUENCE
	frAtmBkPvcVccIfB	IntfIndex
	frAtmBkPvcVccVpiB	INTEGER
	frAtmBkPvcVccVciB	INTEGER
	frAtmBkPvcVccActivePvc	INTEGER
	frAtmBkPvcVccAutoSwitch	INTEGER
	frAtmBkPvcVccRowStatus	RowStatus
	frAtmBkPvcVccViB	INTEGER
	frAtmBkPvcVccVUNIB	INTEGER
	frAtmBkPvcVccConnFailureCauseB	AtmConnFailureCause

AtmBkPvcVccEntry
SEQUENCE
	atmBkPvcVccIfB	IntfIndex
	atmBkPvcVccVpiB	INTEGER
	atmBkPvcVccVciB	INTEGER
	atmBkPvcVccActivePvc	INTEGER
	atmBkPvcVccAutoSwitch	INTEGER
	atmBkPvcVccRowStatus	RowStatus
	atmBkPvcVccViB	INTEGER
	atmBkPvcVccVUNIB	INTEGER
	atmBkPvcVccConnFailureCauseB	AtmConnFailureCause

AtmBkPvcVpcEntry
SEQUENCE
	atmBkPvcVpcIfB	IntfIndex
	atmBkPvcVpcVpiB	INTEGER
	atmBkPvcVpcActivePvc	INTEGER
	atmBkPvcVpcAutoSwitch	INTEGER
	atmBkPvcVpcRowStatus	RowStatus
	atmBkPvcVpcViB	INTEGER
	atmBkPvcVpcVUNIB	INTEGER
	atmBkPvcVpcConnFailureCauseB	AtmConnFailureCause

BridgeAtmBkPvcVccEntry
SEQUENCE
	bridgeAtmBkPvcVccIfB	IntfIndex
	bridgeAtmBkPvcVccVpiB	INTEGER
	bridgeAtmBkPvcVccVciB	INTEGER
	bridgeAtmBkPvcVccActivePvc	INTEGER
	bridgeAtmBkPvcVccAutoSwitch	INTEGER
	bridgeAtmBkPvcVccRowStatus	RowStatus
	bridgeAtmBkPvcVccViB	INTEGER
	bridgeAtmBkPvcVccVUNIB	INTEGER
	bridgeAtmBkPvcVccConnFailureCauseB	AtmConnFailureCause

IpAtmBkAppPvcVccEntry
SEQUENCE
	ipAtmBkAppPvcVccIfB	IntfIndex
	ipAtmBkAppPvcVccVpiB	INTEGER
	ipAtmBkAppPvcVccVciB	INTEGER
	ipAtmBkAppPvcVccActivePvc	INTEGER
	ipAtmBkAppPvcVccAutoSwitch	INTEGER
	ipAtmBkAppPvcVccRowStatus	RowStatus
	ipAtmBkAppPvcVccViB	INTEGER
	ipAtmBkAppPvcVccVUNIB	INTEGER
	ipAtmBkAppPvcVccConnFailureCauseB	AtmConnFailureCause

SpvcAddrEntry
SEQUENCE
	spvcAddrIfA	IntfIndex
	spvcAddrLocalPortAddr	OCTET STRING
	spvcAddrRowStatus	RowStatus

FrAtmSpvcVccEntry
SEQUENCE
	frAtmSpvcVccDlciA	Integer32
	frAtmSpvcVccIfB	IntfIndex
	frAtmSpvcVccVpiB	INTEGER
	frAtmSpvcVccVciB	INTEGER
	frAtmSpvcVccMaxFrameSizeIn	Integer32
	frAtmSpvcVccBcIn	Integer32
	frAtmSpvcVccBeIn	Integer32
	frAtmSpvcVccCirIn	Integer32
	frAtmSpvcVccMaxFrameSizeOut	Integer32
	frAtmSpvcVccBcOut	Integer32
	frAtmSpvcVccBeOut	Integer32
	frAtmSpvcVccCirOut	Integer32
	frAtmSpvcVccServiceType	INTEGER
	frAtmSpvcVccFlow	INTEGER
	frAtmSpvcVccTimeLenIn	INTEGER
	frAtmSpvcVccTimeLenOut	INTEGER
	frAtmSpvcVccPeakCellRateA2B	Integer32
	frAtmSpvcVccSusCellRateA2B	Integer32
	frAtmSpvcVccMaxBurstSizeA2B	Integer32
	frAtmSpvcVccPeakCellRateB2A	Integer32
	frAtmSpvcVccSusCellRateB2A	Integer32
	frAtmSpvcVccMaxBurstSizeB2A	Integer32
	frAtmSpvcVccInterWorkingFunc	INTEGER
	frAtmSpvcVccConnType	INTEGER
	frAtmSpvcVccOperStatus	INTEGER
	frAtmSpvcVccRowStatus	RowStatus
	frAtmSpvcVccRemoteFrPortAddr	OCTET STRING
	frAtmSpvcVccRemoteSelectType	INTEGER
	frAtmSpvcVccRemoteDlci	INTEGER
	frAtmSpvcVccRemoteVpi	INTEGER
	frAtmSpvcVccRemoteVci	INTEGER
	frAtmSpvcVccRetryInterval	INTEGER
	frAtmSpvcVccRetryLimit	INTEGER
	frAtmSpvcVccRestart	INTEGER
	frAtmSpvcVccRetryFailure	Integer32
	frAtmSpvcVccReleaseCause	INTEGER
	frAtmSpvcVccReleaseDiag	OCTET STRING
	frAtmSpvcVccRelease	INTEGER
	frAtmSpvcVccStatsCellsEncodedHiA	Integer32
	frAtmSpvcVccStatsCellsEncodedLoA	Integer32
	frAtmSpvcVccStatsCellsDecodedHiA	Integer32
	frAtmSpvcVccStatsCellsDecodedLoA	Integer32
	frAtmSpvcVccStatsInCellCountHiB	Integer32
	frAtmSpvcVccStatsInCellCountLoB	Integer32
	frAtmSpvcVccStatsOutCellCountHiB	Integer32
	frAtmSpvcVccStatsOutCellCountLoB	Integer32
	frAtmSpvcVccStatsTimer	Integer32
	frAtmSpvcVccStatsFramesDroppedA	Integer32
	frAtmSpvcVccStatsOdometerCellsEncodedHiA	Integer32
	frAtmSpvcVccStatsOdometerCellsEncodedLoA	Integer32
	frAtmSpvcVccStatsOdometerCellsDecodedHiA	Integer32
	frAtmSpvcVccStatsOdometerCellsDecodedLoA	Integer32
	frAtmSpvcVccStatsInOdometerCellCountHiB	Integer32
	frAtmSpvcVccStatsInOdometerCellCountLoB	Integer32
	frAtmSpvcVccStatsOutOdometerCellCountHiB	Integer32
	frAtmSpvcVccStatsOutOdometerCellCountLoB	Integer32
	frAtmSpvcVccStatsOdometerTimer	Integer32
	frAtmSpvcVccStatsOdometerReset	INTEGER
	frAtmSpvcVccStatsAal5ErrFramesA	Integer32
	frAtmSpvcVccStatsFramesTaggedA	Integer32
	frAtmSpvcVccStatsCellsDroppedB	Integer32
	frAtmSpvcVccStatsCellsTaggedB	Integer32
	frAtmSpvcVccVUNIB	INTEGER
	frAtmSpvcVccTrafficShapingA2B	INTEGER
	frAtmSpvcVccPriority	INTEGER

AtmAtmSpvcVccEntry
SEQUENCE
	atmAtmSpvcVccVpiA	INTEGER
	atmAtmSpvcVccVciA	INTEGER
	atmAtmSpvcVccRemoteAtmPortAddr	OCTET STRING
	atmAtmSpvcVccIfB	IntfIndex
	atmAtmSpvcVccVpiB	INTEGER
	atmAtmSpvcVccVciB	INTEGER
	atmAtmSpvcVccServiceTypeA2B	INTEGER
	atmAtmSpvcVccSarTypeA2B	INTEGER
	atmAtmSpvcVccPeakCellRateA2B	Integer32
	atmAtmSpvcVccSusCellRateA2B	Integer32
	atmAtmSpvcVccMaxBurstSizeA2B	Integer32
	atmAtmSpvcVccFrwdErrCorrectionA2B	INTEGER
	atmAtmSpvcVccServiceTypeB2A	INTEGER
	atmAtmSpvcVccSarTypeB2A	INTEGER
	atmAtmSpvcVccPeakCellRateB2A	Integer32
	atmAtmSpvcVccSusCellRateB2A	Integer32
	atmAtmSpvcVccMaxBurstSizeB2A	Integer32
	atmAtmSpvcVccFrwdErrCorrectionB2A	INTEGER
	atmAtmSpvcVccFlow	INTEGER
	atmAtmSpvcVccType	INTEGER
	atmAtmSpvcVccConnType	INTEGER
	atmAtmSpvcVccLeafReference	INTEGER
	atmAtmSpvcVccOperStatus	INTEGER
	atmAtmSpvcVccRowStatus	RowStatus
	atmAtmSpvcVccRemoteSelectType	INTEGER
	atmAtmSpvcVccRemoteVpi	INTEGER
	atmAtmSpvcVccRemoteVci	INTEGER
	atmAtmSpvcVccRetryInterval	INTEGER
	atmAtmSpvcVccRetryLimit	INTEGER
	atmAtmSpvcVccRestart	INTEGER
	atmAtmSpvcVccRetryFailure	Integer32
	atmAtmSpvcVccReleaseCause	INTEGER
	atmAtmSpvcVccReleaseDiag	OCTET STRING
	atmAtmSpvcVccRelease	INTEGER
	atmAtmSpvcVccStatsInCellCountHiA	Integer32
	atmAtmSpvcVccStatsInCellCountLoA	Integer32
	atmAtmSpvcVccStatsOutCellCountHiA	Integer32
	atmAtmSpvcVccStatsOutCellCountLoA	Integer32
	atmAtmSpvcVccStatsInCellCountHiB	Integer32
	atmAtmSpvcVccStatsInCellCountLoB	Integer32
	atmAtmSpvcVccStatsOutCellCountHiB	Integer32
	atmAtmSpvcVccStatsOutCellCountLoB	Integer32
	atmAtmSpvcVccStatsTimer	Integer32
	atmAtmSpvcVccStatsFrwdErrCrrctnRateA2B	INTEGER
	atmAtmSpvcVccStatsFrwdErrCrrctnRateB2A	INTEGER
	atmAtmSpvcVccStatsInOdometerCellCountHiA	Integer32
	atmAtmSpvcVccStatsInOdometerCellCountLoA	Integer32
	atmAtmSpvcVccStatsOutOdometerCellCountHiA	Integer32
	atmAtmSpvcVccStatsOutOdometerCellCountLoA	Integer32
	atmAtmSpvcVccStatsInOdometerCellCountHiB	Integer32
	atmAtmSpvcVccStatsInOdometerCellCountLoB	Integer32
	atmAtmSpvcVccStatsOutOdometerCellCountHiB	Integer32
	atmAtmSpvcVccStatsOutOdometerCellCountLoB	Integer32
	atmAtmSpvcVccStatsOdometerTimer	Integer32
	atmAtmSpvcVccStatsOdometerReset	INTEGER
	atmAtmSpvcVccViA	INTEGER
	atmAtmSpvcVccViB	INTEGER
	atmAtmSpvcVccStatsCellsDroppedA	Integer32
	atmAtmSpvcVccStatsCellsTaggedA	Integer32
	atmAtmSpvcVccStatsCellsDroppedB	Integer32
	atmAtmSpvcVccStatsCellsTaggedB	Integer32
	atmAtmSpvcVccVUNIA	INTEGER
	atmAtmSpvcVccVUNIB	INTEGER
	atmAtmSpvcVccTrafficShapingA2B	INTEGER
	atmAtmSpvcVccTrafficShapingB2A	INTEGER
	atmAtmSpvcVccPriority	INTEGER

CirAtmSpvcVccEntry
SEQUENCE
	cirAtmSpvcVccRemoteCePortAddr	OCTET STRING
	cirAtmSpvcVccIfB	IntfIndex
	cirAtmSpvcVccVpiB	INTEGER
	cirAtmSpvcVccVciB	INTEGER
	cirAtmSpvcVccVoiceCompressionA2B	INTEGER
	cirAtmSpvcVccSilenceDetectionA2B	INTEGER
	cirAtmSpvcVccEchoCancellationA2B	INTEGER
	cirAtmSpvcVccCngToneDetectionA2B	INTEGER
	cirAtmSpvcVccCodingTranslationA2B	INTEGER
	cirAtmSpvcVccVoiceCompressionB2A	INTEGER
	cirAtmSpvcVccSilenceDetectionB2A	INTEGER
	cirAtmSpvcVccEchoCancellationB2A	INTEGER
	cirAtmSpvcVccCngToneDetectionB2A	INTEGER
	cirAtmSpvcVccCodingTranslationB2A	INTEGER
	cirAtmSpvcVccFlow	INTEGER
	cirAtmSpvcVccServiceType	INTEGER
	cirAtmSpvcVccConnType	INTEGER
	cirAtmSpvcVccOperStatus	INTEGER
	cirAtmSpvcVccRowStatus	RowStatus
	cirAtmSpvcVccViB	INTEGER
	cirAtmSpvcVccRetryInterval	INTEGER
	cirAtmSpvcVccRetryLimit	INTEGER
	cirAtmSpvcVccRestart	INTEGER
	cirAtmSpvcVccRetryFailure	Integer32
	cirAtmSpvcVccReleaseCause	INTEGER
	cirAtmSpvcVccReleaseDiag	OCTET STRING
	cirAtmSpvcVccRelease	INTEGER
	cirAtmSpvcVccStatsCellsEncodedHiA	Integer32
	cirAtmSpvcVccStatsCellsEncodedLoA	Integer32
	cirAtmSpvcVccStatsCellsDecodedHiA	Integer32
	cirAtmSpvcVccStatsCellsDecodedLoA	Integer32
	cirAtmSpvcVccStatsInCellCountHiB	Integer32
	cirAtmSpvcVccStatsInCellCountLoB	Integer32
	cirAtmSpvcVccStatsOutCellCountHiB	Integer32
	cirAtmSpvcVccStatsOutCellCountLoB	Integer32
	cirAtmSpvcVccStatsTimer	Integer32
	cirAtmSpvcVccStatsOdometerCellsEncodedHiA	Integer32
	cirAtmSpvcVccStatsOdometerCellsEncodedLoA	Integer32
	cirAtmSpvcVccStatsOdometerCellsDecodedHiA	Integer32
	cirAtmSpvcVccStatsOdometerCellsDecodedLoA	Integer32
	cirAtmSpvcVccStatsInOdometerCellCountHiB	Integer32
	cirAtmSpvcVccStatsInOdometerCellCountLoB	Integer32
	cirAtmSpvcVccStatsOutOdometerCellCountHiB	Integer32
	cirAtmSpvcVccStatsOutOdometerCellCountLoB	Integer32
	cirAtmSpvcVccStatsOdometerTimer	Integer32
	cirAtmSpvcVccStatsOdometerReset	INTEGER
	cirAtmSpvcVccStatsCellsDroppedB	Integer32
	cirAtmSpvcVccStatsCellsTaggedB	Integer32
	cirAtmSpvcVccVUNIB	INTEGER
	cirAtmSpvcVccSarTypeB	Integer32
	cirAtmSpvcVccPriority	INTEGER

VbrAtmSpvcEntry
SEQUENCE
	vbrAtmSpvcRemoteVbrPortAddr	OCTET STRING
	vbrAtmSpvcIfB	IntfIndex
	vbrAtmSpvcVpiB	INTEGER
	vbrAtmSpvcVciB	INTEGER
	vbrAtmSpvcServiceType	INTEGER
	vbrAtmSpvcPeakCellRateA2B	Integer32
	vbrAtmSpvcSusCellRateA2B	Integer32
	vbrAtmSpvcMaxBurstSizeA2B	Integer32
	vbrAtmSpvcPeakCellRateB2A	Integer32
	vbrAtmSpvcSusCellRateB2A	Integer32
	vbrAtmSpvcMaxBurstSizeB2A	Integer32
	vbrAtmSpvcFlow	INTEGER
	vbrAtmSpvcConnType	INTEGER
	vbrAtmSpvcOperStatus	INTEGER
	vbrAtmSpvcRowStatus	RowStatus
	vbrAtmSpvcViB	INTEGER
	vbrAtmSpvcRetryInterval	INTEGER
	vbrAtmSpvcRetryLimit	INTEGER
	vbrAtmSpvcRestart	INTEGER
	vbrAtmSpvcRetryFailure	Integer32
	vbrAtmSpvcReleaseCause	INTEGER
	vbrAtmSpvcReleaseDiag	OCTET STRING
	vbrAtmSpvcRelease	INTEGER
	vbrAtmSpvcStatsCellsEncodedHiA	Integer32
	vbrAtmSpvcStatsCellsEncodedLoA	Integer32
	vbrAtmSpvcStatsCellsDecodedHiA	Integer32
	vbrAtmSpvcStatsCellsDecodedLoA	Integer32
	vbrAtmSpvcStatsInCellCountHiB	Integer32
	vbrAtmSpvcStatsInCellCountLoB	Integer32
	vbrAtmSpvcStatsOutCellCountHiB	Integer32
	vbrAtmSpvcStatsOutCellCountLoB	Integer32
	vbrAtmSpvcStatsTimer	Integer32
	vbrAtmSpvcStatsOdometerCellsEncodedHiA	Integer32
	vbrAtmSpvcStatsOdometerCellsEncodedLoA	Integer32
	vbrAtmSpvcStatsOdometerCellsDecodedHiA	Integer32
	vbrAtmSpvcStatsOdometerCellsDecodedLoA	Integer32
	vbrAtmSpvcStatsInOdometerCellCountHiB	Integer32
	vbrAtmSpvcStatsInOdometerCellCountLoB	Integer32
	vbrAtmSpvcStatsOutOdometerCellCountHiB	Integer32
	vbrAtmSpvcStatsOutOdometerCellCountLoB	Integer32
	vbrAtmSpvcStatsOdometerTimer	Integer32
	vbrAtmSpvcStatsOdometerReset	INTEGER
	vbrAtmSpvcStatsCellsDroppedB	Integer32
	vbrAtmSpvcStatsCellsTaggedB	Integer32
	vbrAtmSpvcVUNIB	INTEGER
	vbrAtmSpvcTrafficShapingA2B	INTEGER
	vbrAtmSpvcPriority	INTEGER

Aal2TrunkConfigEntry
SEQUENCE
	aal2TrunkConfigIf	IntfIndex
	aal2TrunkConfigVpi	INTEGER
	aal2TrunkConfigVci	INTEGER
	aal2TrunkConfigServiceType	INTEGER
	aal2TrunkConfigPeakCellRateIgr	Integer32
	aal2TrunkConfigSusCellRateIgr	Integer32
	aal2TrunkConfigMaxBurstSizeIgr	Integer32
	aal2TrunkConfigPeakCellRateEgr	Integer32
	aal2TrunkConfigSusCellRateEgr	Integer32
	aal2TrunkConfigMaxBurstSizeEgr	Integer32
	aal2TrunkConfigFlow	INTEGER
	aal2TrunkConfigRowStatus	RowStatus
	aal2TrunkConfigConnectionStatus	INTEGER
	aal2TrunkConfigViB	INTEGER
	aal2TrunkConfigCnfrmTypeB2A	INTEGER
	aal2TrunkConfigVUNIB	INTEGER
	aal2TrunkAvailBwIgr	INTEGER
	aal2TrunkAvailBwEgr	INTEGER
	aal2TrunkGR303	INTEGER
	aal2TrunkConfigOamStatus	INTEGER
	aal2TrunkConnFailureCauseB	AtmConnFailureCause
	aal2TrunkCuTimer	INTEGER

Gr303Aal2PvcVccEntry
SEQUENCE
	gr303Aal2PvcVccGr303IgId	INTEGER
	gr303Aal2PvcVccGr303CallRef	INTEGER
	gr303Aal2PvcVccIfB	IntfIndex
	gr303Aal2PvcVccVpiB	INTEGER
	gr303Aal2PvcVccVciB	INTEGER
	gr303Aal2PvcVccAal2Cid	INTEGER
	gr303Aal2PvcVccRowStatus	RowStatus
	gr303Aal2PvcVccVoiceEncodingProfile	INTEGER
	gr303Aal2PvcVccVoiceCompression	INTEGER
	gr303Aal2PvcVccSilenceDetection	INTEGER
	gr303Aal2PvcVccEchoCancellation	INTEGER
	gr303Aal2PvcVccCngToneDetection	INTEGER
	gr303Aal2PvcVccCodingTranslation	INTEGER
	gr303Aal2PvcVccConnectionStatus	INTEGER
	gr303Aal2PvcVccAltLineType	INTEGER

AtmAtmSpvcVpcEntry
SEQUENCE
	atmAtmSpvcVpcVpiA	INTEGER
	atmAtmSpvcVpcRemoteAtmPortAddr	OCTET STRING
	atmAtmSpvcVpcIfB	IntfIndex
	atmAtmSpvcVpcVpiB	INTEGER
	atmAtmSpvcVpcServiceTypeA2B	INTEGER
	atmAtmSpvcVpcSarTypeA2B	INTEGER
	atmAtmSpvcVpcPeakCellRateA2B	Integer32
	atmAtmSpvcVpcSusCellRateA2B	Integer32
	atmAtmSpvcVpcMaxBurstSizeA2B	Integer32
	atmAtmSpvcVpcFrwdErrCorrectionA2B	INTEGER
	atmAtmSpvcVpcServiceTypeB2A	INTEGER
	atmAtmSpvcVpcSarTypeB2A	INTEGER
	atmAtmSpvcVpcPeakCellRateB2A	Integer32
	atmAtmSpvcVpcSusCellRateB2A	Integer32
	atmAtmSpvcVpcMaxBurstSizeB2A	Integer32
	atmAtmSpvcVpcFrwdErrCorrectionB2A	INTEGER
	atmAtmSpvcVpcFlow	INTEGER
	atmAtmSpvcVpcType	INTEGER
	atmAtmSpvcVpcConnType	INTEGER
	atmAtmSpvcVpcLeafReference	INTEGER
	atmAtmSpvcVpcOperStatus	INTEGER
	atmAtmSpvcVpcRowStatus	RowStatus
	atmAtmSpvcVpcRemoteSelectType	INTEGER
	atmAtmSpvcVpcRemoteVpi	INTEGER
	atmAtmSpvcVpcRetryInterval	INTEGER
	atmAtmSpvcVpcRetryLimit	INTEGER
	atmAtmSpvcVpcRestart	INTEGER
	atmAtmSpvcVpcRetryFailure	Integer32
	atmAtmSpvcVpcReleaseCause	INTEGER
	atmAtmSpvcVpcReleaseDiag	OCTET STRING
	atmAtmSpvcVpcRelease	INTEGER
	atmAtmSpvcVpcStatsInCellCountHiA	Integer32
	atmAtmSpvcVpcStatsInCellCountLoA	Integer32
	atmAtmSpvcVpcStatsOutCellCountHiA	Integer32
	atmAtmSpvcVpcStatsOutCellCountLoA	Integer32
	atmAtmSpvcVpcStatsInCellCountHiB	Integer32
	atmAtmSpvcVpcStatsInCellCountLoB	Integer32
	atmAtmSpvcVpcStatsOutCellCountHiB	Integer32
	atmAtmSpvcVpcStatsOutCellCountLoB	Integer32
	atmAtmSpvcVpcStatsTimer	Integer32
	atmAtmSpvcVpcStatsFrwdErrCrrctnRateA2B	INTEGER
	atmAtmSpvcVpcStatsFrwdErrCrrctnRateB2A	INTEGER
	atmAtmSpvcVpcStatsInOdometerCellCountHiA	Integer32
	atmAtmSpvcVpcStatsInOdometerCellCountLoA	Integer32
	atmAtmSpvcVpcStatsOutOdometerCellCountHiA	Integer32
	atmAtmSpvcVpcStatsOutOdometerCellCountLoA	Integer32
	atmAtmSpvcVpcStatsInOdometerCellCountHiB	Integer32
	atmAtmSpvcVpcStatsInOdometerCellCountLoB	Integer32
	atmAtmSpvcVpcStatsOutOdometerCellCountHiB	Integer32
	atmAtmSpvcVpcStatsOutOdometerCellCountLoB	Integer32
	atmAtmSpvcVpcStatsOdometerTimer	Integer32
	atmAtmSpvcVpcStatsOdometerReset	INTEGER
	atmAtmSpvcVpcViA	INTEGER
	atmAtmSpvcVpcViB	INTEGER
	atmAtmSpvcVpcStatsCellsDroppedA	Integer32
	atmAtmSpvcVpcStatsCellsTaggedA	Integer32
	atmAtmSpvcVpcStatsCellsDroppedB	Integer32
	atmAtmSpvcVpcStatsCellsTaggedB	Integer32
	atmAtmSpvcVpcVUNIA	INTEGER
	atmAtmSpvcVpcVUNIB	INTEGER
	atmAtmSpvcVpcTrafficShapingA2B	INTEGER
	atmAtmSpvcVpcTrafficShapingB2A	INTEGER
	atmAtmSpvcVpcPriority	INTEGER

IntfAtmConnDisplayEntry
SEQUENCE
	intfAtmPvcConnDisplaySlot	Integer32
	intfAtmPvcConnDisplayPort	Integer32
	intfAtmPvcConnDisplayChannel	Integer32
	intfAtmPvcConnDisplayVpi	INTEGER
	intfAtmPvcConnDisplayVci	INTEGER
	intfAtmPvcConnDisplayFlowType	INTEGER

Ds3PortStatsEntry
SEQUENCE
	ds3PortStatsId	Integer32
	ds3PortStatsTimer	Integer32
	ds3PortStatsCurrentSEFSs	Integer32
	ds3PortStatsCurrentLCVs	Integer32
	ds3PortStatsCurrentLESs	Integer32

Ds1PortStatsEntry
SEQUENCE
	ds1PortStatsId	Integer32
	ds1PortStatsTimer	Integer32
	ds1PortStatsCurrentESs	Integer32
	ds1PortStatsCurrentSESs	Integer32
	ds1PortStatsCurrentLCVs	Integer32

Oc3PortStatsEntry
SEQUENCE
	oc3PortStatsId	Integer32
	oc3PortStatsSectionBip8Errs	Integer32
	oc3PortStatsLineBip8Errs	Integer32
	oc3PortStatsPathBip8Errs	Integer32
	oc3PortStatsLineFebeCount	Integer32
	oc3PortStatsPathFebeCount	Integer32
	oc3PortStatsTimer	Integer32

MsPortStatsEntry
SEQUENCE
	msPortStatsId	Integer32
	msPortStatsFrameErrors	Integer32
	msPortStatsOutOfFrameSeconds	Integer32
	msPortStatsTimer	Integer32

E3PortStatsEntry
SEQUENCE
	e3PortStatsId	Integer32
	e3PortStatsTimer	Integer32
	e3PortStatsCurrentSEFSs	Integer32
	e3PortStatsCurrentLCVs	Integer32
	e3PortStatsCurrentLESs	Integer32

E1PortStatsEntry
SEQUENCE
	e1PortStatsId	Integer32
	e1PortStatsTimer	Integer32
	e1PortStatsCurrentESs	Integer32
	e1PortStatsCurrentSESs	Integer32
	e1PortStatsCurrentLCVs	Integer32

EthernetPortStatsEntry
SEQUENCE
	ethernetPortStatsId	Integer32
	ethernetPortStatsTimer	Integer32
	ethernetPortStatsAlignmentErrors	Integer32
	ethernetPortStatsFCSErrors	Integer32
	ethernetPortStatsSingleCollisionFrames	Integer32
	ethernetPortStatsMultipleCollisionFrames	Integer32
	ethernetPortStatsSQETestErrors	Integer32
	ethernetPortStatsDeferredTransmissions	Integer32
	ethernetPortStatsLateCollisions	Integer32
	ethernetPortStatsExcessiveCollisions	Integer32
	ethernetPortStatsInternalMacTransmitErrors	Integer32
	ethernetPortStatsCarrierSenseErrors	Integer32
	ethernetPortStatsFrameTooLongs	Integer32
	ethernetPortStatsInternalMacReceiveErrors	Integer32

AtmIfStatsEntry
SEQUENCE
	atmIfStatsId	IntfIndex
	atmIfStatsValidCellsInHi	Integer32
	atmIfStatsValidCellsInLo	Integer32
	atmIfStatsErroredCellsIn	Integer32
	atmIfStatsMismatchedCellsIn	Integer32
	atmIfStatsNullCellsOutHi	Integer32
	atmIfStatsNullCellsOutLo	Integer32
	atmIfStatsValidCellsOutHi	Integer32
	atmIfStatsValidCellsOutLo	Integer32
	atmIfStatsTimer	Integer32

FrUniStatsEntry
SEQUENCE
	frUniStatsId	IntfIndex
	frUniStatsTimer	INTEGER
	frUniStatsCellsMismatched	Integer32
	frUniStatsErroredFrames	Integer32
	frUniStatsCellsEncodedHi	Integer32
	frUniStatsCellsEncodedLo	Integer32
	frUniStatsFramesEncodedHi	Integer32
	frUniStatsFramesEncodedLo	Integer32
	frUniStatsCellsDecodedHi	Integer32
	frUniStatsCellsDecodedLo	Integer32
	frUniStatsFramesDecodedHi	Integer32
	frUniStatsFramesDecodedLo	Integer32
	frUniStatsAAL5Errors	Integer32

CirEmIfStatsEntry
SEQUENCE
	cirEmIfStatsId	IntfIndex
	cirEmIfStatsCellsEncodedHi	Integer32
	cirEmIfStatsCellsEncodedLo	Integer32
	cirEmIfStatsCellsDecodedHi	Integer32
	cirEmIfStatsCellsDecodedLo	Integer32
	cirEmIfStatsTimer	Integer32

VbrIfStatsEntry
SEQUENCE
	vbrIfStatsId	IntfIndex
	vbrIfStatsCellsEncodedHi	Integer32
	vbrIfStatsCellsEncodedLo	Integer32
	vbrIfStatsCellsDecodedHi	Integer32
	vbrIfStatsCellsDecodedLo	Integer32
	vbrIfStatsTimer	Integer32

FrLmiStatsEntry
SEQUENCE
	frLmiStatsId	IntfIndex
	frLmiStatsEnqRx	Integer32
	frLmiStatsEnqTx	Integer32
	frLmiStatsStatusRx	Integer32
	frLmiStatsStatusTx	Integer32
	frLmiStatsAsyncRx	Integer32
	frLmiStatsAsyncTx	Integer32
	frLmiStatsPktDisc	Integer32
	frLmiStatsT391Exp	INTEGER
	frLmiStatsT392Exp	INTEGER
	frLmiStatsLinkReset	INTEGER
	frLmiStatsTimer	INTEGER

BridgeStatsEntry
SEQUENCE
	bridgeStatsId	Integer32
	bridgeStatsTimer	Integer32
	bridgeStatsBasePortDelayExceededDiscardsHi	Integer32
	bridgeStatsBasePortDelayExceededDiscardsLo	Integer32
	bridgeStatsBasePortMtuExceededDiscardsHi	Integer32
	bridgeStatsBasePortMtuExceededDiscardsLo	Integer32
	bridgeStatsTpPortInFramesHi	Integer32
	bridgeStatsTpPortInFramesLo	Integer32
	bridgeStatsTpPortOutFramesHi	Integer32
	bridgeStatsTpPortOutFramesLo	Integer32
	bridgeStatsTpPortInDiscardsHi	Integer32
	bridgeStatsTpPortInDiscardsLo	Integer32

DbCirEmIfStatsEntry
SEQUENCE
	dbCirEmIfStatsId	IntfIndex
	dbCirEmIfStatsCellsEncodedHi	Integer32
	dbCirEmIfStatsCellsEncodedLo	Integer32
	dbCirEmIfStatsCellsDecodedHi	Integer32
	dbCirEmIfStatsCellsDecodedLo	Integer32
	dbCirEmIfStatsTimer	Integer32

AtmImaStatsEntry
SEQUENCE
	atmImaStatsId	IntfIndex
	atmImaStatsTimer	Integer32
	atmImaStatsImaViolations	Integer32
	atmImaStatsOifAnomalies	Integer32
	atmImaStatsNeTxNumFailures	Integer32
	atmImaStatsNeRxNumFailures	Integer32
	atmImaStatsFeTxNumFailures	Integer32
	atmImaStatsFeRxNumFailures	Integer32
	atmImaStatsTxStuffs	Integer32
	atmImaStatsRxStuffs	Integer32

IlmiStatsEntry
SEQUENCE
	ilmiStatsId	IntfIndex
	ilmiStatsTimer	Integer32
	ilmiStatsLinkResets	Integer32
	ilmiStatsAttachPtChanged	Integer32
	ilmiStatsAttachPtVerified	Integer32
	ilmiStatsSecureLnkProcInit	Integer32
	ilmiStatsColdStartRx	Integer32
	ilmiStatsColdStartTx	Integer32
	ilmiStatsPduRx	Integer32
	ilmiStatsPduTx	Integer32
	ilmiStatsReqTimeouts	Integer32
	ilmiStatsPacketDisc	Integer32

VuniIlmiStatsEntry
SEQUENCE
	vuniIlmiStatsId	IntfIndex
	vuniIlmiVUNIId	INTEGER
	vuniIlmiStatsTimer	Integer32
	vuniIlmiStatsLinkResets	Integer32
	vuniIlmiStatsAttachPtChanged	Integer32
	vuniIlmiStatsAttachPtVerified	Integer32
	vuniIlmiStatsSecureLnkProcInit	Integer32
	vuniIlmiStatsColdStartRx	Integer32
	vuniIlmiStatsColdStartTx	Integer32
	vuniIlmiStatsPduRx	Integer32
	vuniIlmiStatsPduTx	Integer32
	vuniIlmiStatsReqTimeouts	Integer32
	vuniIlmiStatsPacketDisc	Integer32
	vuniResetIlmiStatistics	INTEGER

AtmPvcVccStatsEntry
SEQUENCE
	atmPvcVccStatsIfA	IntfIndex
	atmPvcVccStatsVpiA	INTEGER
	atmPvcVccStatsVciA	INTEGER
	atmPvcVccStatsIfB	IntfIndex
	atmPvcVccStatsVpiB	INTEGER
	atmPvcVccStatsVciB	INTEGER
	atmPvcVccStatsInCellCountHiA	Integer32
	atmPvcVccStatsInCellCountLoA	Integer32
	atmPvcVccStatsOutCellCountHiA	Integer32
	atmPvcVccStatsOutCellCountLoA	Integer32
	atmPvcVccStatsInCellCountHiB	Integer32
	atmPvcVccStatsInCellCountLoB	Integer32
	atmPvcVccStatsOutCellCountHiB	Integer32
	atmPvcVccStatsOutCellCountLoB	Integer32
	atmPvcVccStatsTimer	Integer32
	atmPvcVccStatsFrwdErrCrrctnRateA2B	INTEGER
	atmPvcVccStatsFrwdErrCrrctnRateB2A	INTEGER
	atmPvcVccStatsInOdometerCellCountHiA	Integer32
	atmPvcVccStatsInOdometerCellCountLoA	Integer32
	atmPvcVccStatsOutOdometerCellCountHiA	Integer32
	atmPvcVccStatsOutOdometerCellCountLoA	Integer32
	atmPvcVccStatsInOdometerCellCountHiB	Integer32
	atmPvcVccStatsInOdometerCellCountLoB	Integer32
	atmPvcVccStatsOutOdometerCellCountHiB	Integer32
	atmPvcVccStatsOutOdometerCellCountLoB	Integer32
	atmPvcVccStatsOdometerTimer	Integer32
	atmPvcVccStatsOdometerReset	INTEGER
	atmPvcVccStatsOamAisTxA	Integer32
	atmPvcVccStatsOamAisRxA	Integer32
	atmPvcVccStatsOamRdiTxA	Integer32
	atmPvcVccStatsOamRdiRxA	Integer32
	atmPvcVccStatsOamAisTxB	Integer32
	atmPvcVccStatsOamAisRxB	Integer32
	atmPvcVccStatsOamRdiTxB	Integer32
	atmPvcVccStatsOamRdiRxB	Integer32
	atmPvcVccStatsCellsDroppedA	Integer32
	atmPvcVccStatsCellsTaggedA	Integer32
	atmPvcVccStatsCellsDroppedB	Integer32
	atmPvcVccStatsCellsTaggedB	Integer32

AtmPvcVpcStatsEntry
SEQUENCE
	atmPvcVpcStatsIfA	IntfIndex
	atmPvcVpcStatsVpiA	INTEGER
	atmPvcVpcStatsIfB	IntfIndex
	atmPvcVpcStatsVpiB	INTEGER
	atmPvcVpcStatsInCellCountHiA	Integer32
	atmPvcVpcStatsInCellCountLoA	Integer32
	atmPvcVpcStatsOutCellCountHiA	Integer32
	atmPvcVpcStatsOutCellCountLoA	Integer32
	atmPvcVpcStatsInCellCountHiB	Integer32
	atmPvcVpcStatsInCellCountLoB	Integer32
	atmPvcVpcStatsOutCellCountHiB	Integer32
	atmPvcVpcStatsOutCellCountLoB	Integer32
	atmPvcVpcStatsTimer	Integer32
	atmPvcVpcStatsInOdometerCellCountHiA	Integer32
	atmPvcVpcStatsInOdometerCellCountLoA	Integer32
	atmPvcVpcStatsOutOdometerCellCountHiA	Integer32
	atmPvcVpcStatsOutOdometerCellCountLoA	Integer32
	atmPvcVpcStatsInOdometerCellCountHiB	Integer32
	atmPvcVpcStatsInOdometerCellCountLoB	Integer32
	atmPvcVpcStatsOutOdometerCellCountHiB	Integer32
	atmPvcVpcStatsOutOdometerCellCountLoB	Integer32
	atmPvcVpcStatsOdometerTimer	Integer32
	atmPvcVpcStatsOdometerReset	INTEGER
	atmPvcVpcStatsOamAisTxA	Integer32
	atmPvcVpcStatsOamAisRxA	Integer32
	atmPvcVpcStatsOamRdiTxA	Integer32
	atmPvcVpcStatsOamRdiRxA	Integer32
	atmPvcVpcStatsOamAisTxB	Integer32
	atmPvcVpcStatsOamAisRxB	Integer32
	atmPvcVpcStatsOamRdiTxB	Integer32
	atmPvcVpcStatsOamRdiRxB	Integer32
	atmPvcVpcStatsCellsDroppedA	Integer32
	atmPvcVpcStatsCellsTaggedA	Integer32
	atmPvcVpcStatsCellsDroppedB	Integer32
	atmPvcVpcStatsCellsTaggedB	Integer32

AtmSvcVccStatsEntry
SEQUENCE
	atmSvcVccStatsIfA	IntfIndex
	atmSvcVccStatsVpiA	INTEGER
	atmSvcVccStatsVciA	INTEGER
	atmSvcVccStatsIfB	IntfIndex
	atmSvcVccStatsVpiB	INTEGER
	atmSvcVccStatsVciB	INTEGER
	atmSvcVccStatsInCellCountHiA	Integer32
	atmSvcVccStatsInCellCountLoA	Integer32
	atmSvcVccStatsOutCellCountHiA	Integer32
	atmSvcVccStatsOutCellCountLoA	Integer32
	atmSvcVccStatsInCellCountHiB	Integer32
	atmSvcVccStatsInCellCountLoB	Integer32
	atmSvcVccStatsOutCellCountHiB	Integer32
	atmSvcVccStatsOutCellCountLoB	Integer32
	atmSvcVccStatsTimer	Integer32
	atmSvcVccStatsInOdometerCellCountHiA	Integer32
	atmSvcVccStatsInOdometerCellCountLoA	Integer32
	atmSvcVccStatsOutOdometerCellCountHiA	Integer32
	atmSvcVccStatsOutOdometerCellCountLoA	Integer32
	atmSvcVccStatsInOdometerCellCountHiB	Integer32
	atmSvcVccStatsInOdometerCellCountLoB	Integer32
	atmSvcVccStatsOutOdometerCellCountHiB	Integer32
	atmSvcVccStatsOutOdometerCellCountLoB	Integer32
	atmSvcVccStatsOdometerTimer	Integer32
	atmSvcVccStatsOdometerReset	INTEGER
	atmSvcVccStatsCellsDroppedA	Integer32
	atmSvcVccStatsCellsTaggedA	Integer32
	atmSvcVccStatsCellsDroppedB	Integer32
	atmSvcVccStatsCellsTaggedB	Integer32

IpAtmAppPvcVccStatsEntry
SEQUENCE
	ipAtmAppPvcVccStatsDestAddrA	IpAddress
	ipAtmAppPvcVccStatsSubnetMaskA	IpAddress
	ipAtmAppPvcVccStatsIfB	IntfIndex
	ipAtmAppPvcVccStatsVpiB	INTEGER
	ipAtmAppPvcVccStatsVciB	INTEGER
	ipAtmAppPvcVccStatsInCellCountHiA	Integer32
	ipAtmAppPvcVccStatsInCellCountLoA	Integer32
	ipAtmAppPvcVccStatsOutCellCountHiA	Integer32
	ipAtmAppPvcVccStatsOutCellCountLoA	Integer32
	ipAtmAppPvcVccStatsFramesInB	Integer32
	ipAtmAppPvcVccStatsFramesOutB	Integer32
	ipAtmAppPvcVccStatsInCellCountHiB	Integer32
	ipAtmAppPvcVccStatsInCellCountLoB	Integer32
	ipAtmAppPvcVccStatsOutCellCountHiB	Integer32
	ipAtmAppPvcVccStatsOutCellCountLoB	Integer32
	ipAtmAppPvcVccStatsTimer	Integer32
	ipAtmAppPvcVccStatsInOdometerCellCountHiA	Integer32
	ipAtmAppPvcVccStatsInOdometerCellCountLoA	Integer32
	ipAtmAppPvcVccStatsOutOdometerCellCountHiA	Integer32
	ipAtmAppPvcVccStatsOutOdometerCellCountLoA	Integer32
	ipAtmAppPvcVccStatsOdometerFramesInB	Integer32
	ipAtmAppPvcVccStatsOdometerFramesOutB	Integer32
	ipAtmAppPvcVccStatsInOdometerCellCountHiB	Integer32
	ipAtmAppPvcVccStatsInOdometerCellCountLoB	Integer32
	ipAtmAppPvcVccStatsOutOdometerCellCountHiB	Integer32
	ipAtmAppPvcVccStatsOutOdometerCellCountLoB	Integer32
	ipAtmAppPvcVccStatsOdometerTimer	Integer32
	ipAtmAppPvcVccStatsOdometerReset	INTEGER
	ipAtmAppPvcVccStatsCellsDroppedB	Integer32
	ipAtmAppPvcVccStatsCellsTaggedB	Integer32

IpAtmAppSvcVccStatsEntry
SEQUENCE
	ipAtmAppSvcVccStatsDestAddrA	IpAddress
	ipAtmAppSvcVccStatsSubnetMaskA	IpAddress
	ipAtmAppSvcVccStatsIfB	IntfIndex
	ipAtmAppSvcVccStatsVpiB	INTEGER
	ipAtmAppSvcVccStatsVciB	INTEGER
	ipAtmAppSvcVccStatsInCellCountHiA	Integer32
	ipAtmAppSvcVccStatsInCellCountLoA	Integer32
	ipAtmAppSvcVccStatsOutCellCountHiA	Integer32
	ipAtmAppSvcVccStatsOutCellCountLoA	Integer32
	ipAtmAppSvcVccStatsFramesInB	Integer32
	ipAtmAppSvcVccStatsFramesOutB	Integer32
	ipAtmAppSvcVccStatsInCellCountHiB	Integer32
	ipAtmAppSvcVccStatsInCellCountLoB	Integer32
	ipAtmAppSvcVccStatsOutCellCountHiB	Integer32
	ipAtmAppSvcVccStatsOutCellCountLoB	Integer32
	ipAtmAppSvcVccStatsTimer	Integer32
	ipAtmAppSvcVccStatsCellsDroppedB	Integer32
	ipAtmAppSvcVccStatsCellsTaggedB	Integer32

CirEmAtmPvcVccStatsEntry
SEQUENCE
	cirEmAtmPvcVccStatsIfA	IntfIndex
	cirEmAtmPvcVccStatsIfB	IntfIndex
	cirEmAtmPvcVccStatsVpiB	INTEGER
	cirEmAtmPvcVccStatsVciB	INTEGER
	cirEmAtmPvcVccStatsCellsEncodedHiA	Integer32
	cirEmAtmPvcVccStatsCellsEncodedLoA	Integer32
	cirEmAtmPvcVccStatsCellsDecodedHiA	Integer32
	cirEmAtmPvcVccStatsCellsDecodedLoA	Integer32
	cirEmAtmPvcVccStatsInCellCountHiB	Integer32
	cirEmAtmPvcVccStatsInCellCountLoB	Integer32
	cirEmAtmPvcVccStatsOutCellCountHiB	Integer32
	cirEmAtmPvcVccStatsOutCellCountLoB	Integer32
	cirEmAtmPvcVccStatsTimer	Integer32
	cirEmAtmPvcVccStatsOdometerCellsEncodedHiA	Integer32
	cirEmAtmPvcVccStatsOdometerCellsEncodedLoA	Integer32
	cirEmAtmPvcVccStatsOdometerCellsDecodedHiA	Integer32
	cirEmAtmPvcVccStatsOdometerCellsDecodedLoA	Integer32
	cirEmAtmPvcVccStatsInOdometerCellCountHiB	Integer32
	cirEmAtmPvcVccStatsInOdometerCellCountLoB	Integer32
	cirEmAtmPvcVccStatsOutOdometerCellCountHiB	Integer32
	cirEmAtmPvcVccStatsOutOdometerCellCountLoB	Integer32
	cirEmAtmPvcVccStatsOdometerTimer	Integer32
	cirEmAtmPvcVccStatsOdometerReset	INTEGER
	cirEmAtmPvcVccStatsOamAisTx	Integer32
	cirEmAtmPvcVccStatsOamAisRx	Integer32
	cirEmAtmPvcVccStatsOamRdiTx	Integer32
	cirEmAtmPvcVccStatsOamRdiRx	Integer32
	cirEmAtmPvcVccStatsCellsDroppedB	Integer32
	cirEmAtmPvcVccStatsCellsTaggedB	Integer32

FrAtmPvcVccStatsEntry
SEQUENCE
	frAtmPvcVccStatsIfA	IntfIndex
	frAtmPvcVccStatsDlciA	INTEGER
	frAtmPvcVccStatsIfB	IntfIndex
	frAtmPvcVccStatsVpiB	INTEGER
	frAtmPvcVccStatsVciB	INTEGER
	frAtmPvcVccStatsCellsEncodedHiA	Integer32
	frAtmPvcVccStatsCellsEncodedLoA	Integer32
	frAtmPvcVccStatsCellsDecodedHiA	Integer32
	frAtmPvcVccStatsCellsDecodedLoA	Integer32
	frAtmPvcVccStatsInCellCountHiB	Integer32
	frAtmPvcVccStatsInCellCountLoB	Integer32
	frAtmPvcVccStatsOutCellCountHiB	Integer32
	frAtmPvcVccStatsOutCellCountLoB	Integer32
	frAtmPvcVccStatsTimer	Integer32
	frAtmPvcVccStatsFramesDroppedA	Integer32
	frAtmPvcVccStatsOdometerCellsEncodedHiA	Integer32
	frAtmPvcVccStatsOdometerCellsEncodedLoA	Integer32
	frAtmPvcVccStatsOdometerCellsDecodedHiA	Integer32
	frAtmPvcVccStatsOdometerCellsDecodedLoA	Integer32
	frAtmPvcVccStatsInOdometerCellCountHiB	Integer32
	frAtmPvcVccStatsInOdometerCellCountLoB	Integer32
	frAtmPvcVccStatsOutOdometerCellCountHiB	Integer32
	frAtmPvcVccStatsOutOdometerCellCountLoB	Integer32
	frAtmPvcVccStatsOdometerTimer	Integer32
	frAtmPvcVccStatsOdometerFramesDroppedA	Integer32
	frAtmPvcVccStatsOdometerReset	INTEGER
	frAtmPvcVccStatsOamAisTx	Integer32
	frAtmPvcVccStatsOamAisRx	Integer32
	frAtmPvcVccStatsOamRdiTx	Integer32
	frAtmPvcVccStatsOamRdiRx	Integer32
	frAtmPvcVccStatsAal5ErrFramesA	Integer32
	frAtmPvcVccStatsFramesTaggedA	Integer32
	frAtmPvcVccStatsCellsDroppedB	Integer32
	frAtmPvcVccStatsCellsTaggedB	Integer32

FrFrPvcStatsEntry
SEQUENCE
	frFrPvcStatsIfA	IntfIndex
	frFrPvcStatsDlciA	INTEGER
	frFrPvcStatsIfB	IntfIndex
	frFrPvcStatsDlciB	INTEGER
	frFrPvcStatsCellsEncodedHiA	Integer32
	frFrPvcStatsCellsEncodedLoA	Integer32
	frFrPvcStatsCellsDecodedHiA	Integer32
	frFrPvcStatsCellsDecodedLoA	Integer32
	frFrPvcStatsCellsEncodedHiB	Integer32
	frFrPvcStatsCellsEncodedLoB	Integer32
	frFrPvcStatsCellsDecodedHiB	Integer32
	frFrPvcStatsCellsDecodedLoB	Integer32
	frFrPvcStatsTimer	Integer32
	frFrPvcStatsFramesDroppedA	Integer32
	frFrPvcStatsFramesDroppedB	Integer32
	frFrPvcStatsOdometerCellsEncodedHiA	Integer32
	frFrPvcStatsOdometerCellsEncodedLoA	Integer32
	frFrPvcStatsOdometerCellsDecodedHiA	Integer32
	frFrPvcStatsOdometerCellsDecodedLoA	Integer32
	frFrPvcStatsOdometerCellsEncodedHiB	Integer32
	frFrPvcStatsOdometerCellsEncodedLoB	Integer32
	frFrPvcStatsOdometerCellsDecodedHiB	Integer32
	frFrPvcStatsOdometerCellsDecodedLoB	Integer32
	frFrPvcStatsOdometerTimer	Integer32
	frFrPvcStatsOdometerFramesDroppedA	Integer32
	frFrPvcStatsOdometerFramesDroppedB	Integer32
	frFrPvcStatsOdometerReset	INTEGER
	frFrPvcStatsAal5ErrFramesA	Integer32
	frFrPvcStatsAal5ErrFramesB	Integer32
	frFrPvcStatsFramesTaggedA	Integer32
	frFrPvcStatsFramesTaggedB	Integer32

VbrAtmPvcVccStatsEntry
SEQUENCE
	vbrAtmPvcVccStatsIfA	IntfIndex
	vbrAtmPvcVccStatsIfB	IntfIndex
	vbrAtmPvcVccStatsVpiB	INTEGER
	vbrAtmPvcVccStatsVciB	INTEGER
	vbrAtmPvcVccStatsCellsEncodedHiA	Integer32
	vbrAtmPvcVccStatsCellsEncodedLoA	Integer32
	vbrAtmPvcVccStatsCellsDecodedHiA	Integer32
	vbrAtmPvcVccStatsCellsDecodedLoA	Integer32
	vbrAtmPvcVccStatsInCellCountHiB	Integer32
	vbrAtmPvcVccStatsInCellCountLoB	Integer32
	vbrAtmPvcVccStatsOutCellCountHiB	Integer32
	vbrAtmPvcVccStatsOutCellCountLoB	Integer32
	vbrAtmPvcVccStatsTimer	Integer32
	vbrAtmPvcVccStatsOdometerCellsEncodedHiA	Integer32
	vbrAtmPvcVccStatsOdometerCellsEncodedLoA	Integer32
	vbrAtmPvcVccStatsOdometerCellsDecodedHiA	Integer32
	vbrAtmPvcVccStatsOdometerCellsDecodedLoA	Integer32
	vbrAtmPvcVccStatsInOdometerCellCountHiB	Integer32
	vbrAtmPvcVccStatsInOdometerCellCountLoB	Integer32
	vbrAtmPvcVccStatsOutOdometerCellCountHiB	Integer32
	vbrAtmPvcVccStatsOutOdometerCellCountLoB	Integer32
	vbrAtmPvcVccStatsOdometerTimer	Integer32
	vbrAtmPvcVccStatsOdometerReset	INTEGER
	vbrAtmPvcVccStatsOamAisTx	Integer32
	vbrAtmPvcVccStatsOamAisRx	Integer32
	vbrAtmPvcVccStatsOamRdiTx	Integer32
	vbrAtmPvcVccStatsOamRdiRx	Integer32
	vbrAtmPvcVccStatsCellsDroppedB	Integer32
	vbrAtmPvcVccStatsCellsTaggedB	Integer32

CirEmCirEmPvcStatsEntry
SEQUENCE
	cirEmCirEmPvcStatsIfA	IntfIndex
	cirEmCirEmPvcStatsIfB	IntfIndex
	cirEmCirEmPvcStatsCellsEncodedHiA	Integer32
	cirEmCirEmPvcStatsCellsEncodedLoA	Integer32
	cirEmCirEmPvcStatsCellsDecodedHiA	Integer32
	cirEmCirEmPvcStatsCellsDecodedLoA	Integer32
	cirEmCirEmPvcStatsCellsEncodedHiB	Integer32
	cirEmCirEmPvcStatsCellsEncodedLoB	Integer32
	cirEmCirEmPvcStatsCellsDecodedHiB	Integer32
	cirEmCirEmPvcStatsCellsDecodedLoB	Integer32
	cirEmCirEmPvcStatsTimer	Integer32
	cirEmCirEmPvcStatsOdometerCellsEncodedHiA	Integer32
	cirEmCirEmPvcStatsOdometerCellsEncodedLoA	Integer32
	cirEmCirEmPvcStatsOdometerCellsDecodedHiA	Integer32
	cirEmCirEmPvcStatsOdometerCellsDecodedLoA	Integer32
	cirEmCirEmPvcStatsOdometerCellsEncodedHiB	Integer32
	cirEmCirEmPvcStatsOdometerCellsEncodedLoB	Integer32
	cirEmCirEmPvcStatsOdometerCellsDecodedHiB	Integer32
	cirEmCirEmPvcStatsOdometerCellsDecodedLoB	Integer32
	cirEmCirEmPvcStatsOdometerTimer	Integer32
	cirEmCirEmPvcStatsOdometerReset	INTEGER

VbrVbrPvcStatsEntry
SEQUENCE
	vbrVbrPvcStatsIfA	IntfIndex
	vbrVbrPvcStatsIfB	IntfIndex
	vbrVbrPvcStatsCellsEncodedHiA	Integer32
	vbrVbrPvcStatsCellsEncodedLoA	Integer32
	vbrVbrPvcStatsCellsDecodedHiA	Integer32
	vbrVbrPvcStatsCellsDecodedLoA	Integer32
	vbrVbrPvcStatsCellsEncodedHiB	Integer32
	vbrVbrPvcStatsCellsEncodedLoB	Integer32
	vbrVbrPvcStatsCellsDecodedHiB	Integer32
	vbrVbrPvcStatsCellsDecodedLoB	Integer32
	vbrVbrPvcStatsTimer	Integer32
	vbrVbrPvcStatsOdometerCellsEncodedHiA	Integer32
	vbrVbrPvcStatsOdometerCellsEncodedLoA	Integer32
	vbrVbrPvcStatsOdometerCellsDecodedHiA	Integer32
	vbrVbrPvcStatsOdometerCellsDecodedLoA	Integer32
	vbrVbrPvcStatsOdometerCellsEncodedHiB	Integer32
	vbrVbrPvcStatsOdometerCellsEncodedLoB	Integer32
	vbrVbrPvcStatsOdometerCellsDecodedHiB	Integer32
	vbrVbrPvcStatsOdometerCellsDecodedLoB	Integer32
	vbrVbrPvcStatsOdometerTimer	Integer32
	vbrVbrPvcStatsOdometerReset	INTEGER

BridgeBridgePvcStatsEntry
SEQUENCE
	bridgeBridgePvcStatsIfA	IntfIndex
	bridgeBridgePvcStatsIfB	IntfIndex
	bridgeBridgePvcStatsCellsEncodedHiA	Integer32
	bridgeBridgePvcStatsCellsEncodedLoA	Integer32
	bridgeBridgePvcStatsCellsDecodedHiA	Integer32
	bridgeBridgePvcStatsCellsDecodedLoA	Integer32
	bridgeBridgePvcStatsCellsEncodedHiB	Integer32
	bridgeBridgePvcStatsCellsEncodedLoB	Integer32
	bridgeBridgePvcStatsCellsDecodedHiB	Integer32
	bridgeBridgePvcStatsCellsDecodedLoB	Integer32
	bridgeBridgePvcStatsTimer	Integer32
	bridgeBridgePvcStatsOdometerCellsEncodedHiA	Integer32
	bridgeBridgePvcStatsOdometerCellsEncodedLoA	Integer32
	bridgeBridgePvcStatsOdometerCellsDecodedHiA	Integer32
	bridgeBridgePvcStatsOdometerCellsDecodedLoA	Integer32
	bridgeBridgePvcStatsOdometerCellsEncodedHiB	Integer32
	bridgeBridgePvcStatsOdometerCellsEncodedLoB	Integer32
	bridgeBridgePvcStatsOdometerCellsDecodedHiB	Integer32
	bridgeBridgePvcStatsOdometerCellsDecodedLoB	Integer32
	bridgeBridgePvcStatsOdometerTimer	Integer32
	bridgeBridgePvcStatsOdometerReset	INTEGER

BridgeAtmPvcVccStatsEntry
SEQUENCE
	bridgeAtmPvcVccStatsIfA	IntfIndex
	bridgeAtmPvcVccStatsIfB	IntfIndex
	bridgeAtmPvcVccStatsVpiB	INTEGER
	bridgeAtmPvcVccStatsVciB	INTEGER
	bridgeAtmPvcVccStatsCellsEncodedHiA	Integer32
	bridgeAtmPvcVccStatsCellsEncodedLoA	Integer32
	bridgeAtmPvcVccStatsCellsDecodedHiA	Integer32
	bridgeAtmPvcVccStatsCellsDecodedLoA	Integer32
	bridgeAtmPvcVccStatsInCellCountHiB	Integer32
	bridgeAtmPvcVccStatsInCellCountLoB	Integer32
	bridgeAtmPvcVccStatsOutCellCountHiB	Integer32
	bridgeAtmPvcVccStatsOutCellCountLoB	Integer32
	bridgeAtmPvcVccStatsTimer	Integer32
	bridgeAtmPvcVccStatsOdometerCellsEncodedHiA	Integer32
	bridgeAtmPvcVccStatsOdometerCellsEncodedLoA	Integer32
	bridgeAtmPvcVccStatsOdometerCellsDecodedHiA	Integer32
	bridgeAtmPvcVccStatsOdometerCellsDecodedLoA	Integer32
	bridgeAtmPvcVccStatsInOdometerCellCountHiB	Integer32
	bridgeAtmPvcVccStatsInOdometerCellCountLoB	Integer32
	bridgeAtmPvcVccStatsOutOdometerCellCountHiB	Integer32
	bridgeAtmPvcVccStatsOutOdometerCellCountLoB	Integer32
	bridgeAtmPvcVccStatsOdometerTimer	Integer32
	bridgeAtmPvcVccStatsOdometerReset	INTEGER
	bridgeAtmPvcVccStatsOamAisTx	Integer32
	bridgeAtmPvcVccStatsOamAisRx	Integer32
	bridgeAtmPvcVccStatsOamRdiTx	Integer32
	bridgeAtmPvcVccStatsOamRdiRx	Integer32
	bridgeAtmPvcVccStatsCellsDroppedB	Integer32
	bridgeAtmPvcVccStatsCellsTaggedB	Integer32

CirEmAtmSpvcVccStatsEntry
SEQUENCE
	cirEmAtmSpvcVccStatsIfA	IntfIndex
	cirEmAtmSpvcVccStatsIfB	IntfIndex
	cirEmAtmSpvcVccStatsVpiB	INTEGER
	cirEmAtmSpvcVccStatsVciB	INTEGER
	cirEmAtmSpvcVccStatsCellsEncodedHiA	Integer32
	cirEmAtmSpvcVccStatsCellsEncodedLoA	Integer32
	cirEmAtmSpvcVccStatsCellsDecodedHiA	Integer32
	cirEmAtmSpvcVccStatsCellsDecodedLoA	Integer32
	cirEmAtmSpvcVccStatsInCellCountHiB	Integer32
	cirEmAtmSpvcVccStatsInCellCountLoB	Integer32
	cirEmAtmSpvcVccStatsOutCellCountHiB	Integer32
	cirEmAtmSpvcVccStatsOutCellCountLoB	Integer32
	cirEmAtmSpvcVccStatsTimer	Integer32
	cirEmAtmSpvcVccStatsOdometerCellsEncodedHiA	Integer32
	cirEmAtmSpvcVccStatsOdometerCellsEncodedLoA	Integer32
	cirEmAtmSpvcVccStatsOdometerCellsDecodedHiA	Integer32
	cirEmAtmSpvcVccStatsOdometerCellsDecodedLoA	Integer32
	cirEmAtmSpvcVccStatsInOdometerCellCountHiB	Integer32
	cirEmAtmSpvcVccStatsInOdometerCellCountLoB	Integer32
	cirEmAtmSpvcVccStatsOutOdometerCellCountHiB	Integer32
	cirEmAtmSpvcVccStatsOutOdometerCellCountLoB	Integer32
	cirEmAtmSpvcVccStatsOdometerTimer	Integer32
	cirEmAtmSpvcVccStatsOdometerReset	INTEGER
	cirEmAtmSpvcVccStatsCellsDroppedB	Integer32
	cirEmAtmSpvcVccStatsCellsTaggedB	Integer32

VbrAtmSpvcVccStatsEntry
SEQUENCE
	vbrAtmSpvcVccStatsIfA	IntfIndex
	vbrAtmSpvcVccStatsIfB	IntfIndex
	vbrAtmSpvcVccStatsVpiB	INTEGER
	vbrAtmSpvcVccStatsVciB	INTEGER
	vbrAtmSpvcVccStatsCellsEncodedHiA	Integer32
	vbrAtmSpvcVccStatsCellsEncodedLoA	Integer32
	vbrAtmSpvcVccStatsCellsDecodedHiA	Integer32
	vbrAtmSpvcVccStatsCellsDecodedLoA	Integer32
	vbrAtmSpvcVccStatsInCellCountHiB	Integer32
	vbrAtmSpvcVccStatsInCellCountLoB	Integer32
	vbrAtmSpvcVccStatsOutCellCountHiB	Integer32
	vbrAtmSpvcVccStatsOutCellCountLoB	Integer32
	vbrAtmSpvcVccStatsTimer	Integer32
	vbrAtmSpvcVccStatsOdometerCellsEncodedHiA	Integer32
	vbrAtmSpvcVccStatsOdometerCellsEncodedLoA	Integer32
	vbrAtmSpvcVccStatsOdometerCellsDecodedHiA	Integer32
	vbrAtmSpvcVccStatsOdometerCellsDecodedLoA	Integer32
	vbrAtmSpvcVccStatsInOdometerCellCountHiB	Integer32
	vbrAtmSpvcVccStatsInOdometerCellCountLoB	Integer32
	vbrAtmSpvcVccStatsOutOdometerCellCountHiB	Integer32
	vbrAtmSpvcVccStatsOutOdometerCellCountLoB	Integer32
	vbrAtmSpvcVccStatsOdometerTimer	Integer32
	vbrAtmSpvcVccStatsOdometerReset	INTEGER
	vbrAtmSpvcVccStatsCellsDroppedB	Integer32
	vbrAtmSpvcVccStatsCellsTaggedB	Integer32

AtmSpvcVccStatsEntry
SEQUENCE
	atmSpvcVccStatsIfA	IntfIndex
	atmSpvcVccStatsVpiA	INTEGER
	atmSpvcVccStatsVciA	INTEGER
	atmSpvcVccStatsIfB	IntfIndex
	atmSpvcVccStatsVpiB	INTEGER
	atmSpvcVccStatsVciB	INTEGER
	atmSpvcVccStatsInCellCountHiA	Integer32
	atmSpvcVccStatsInCellCountLoA	Integer32
	atmSpvcVccStatsOutCellCountHiA	Integer32
	atmSpvcVccStatsOutCellCountLoA	Integer32
	atmSpvcVccStatsInCellCountHiB	Integer32
	atmSpvcVccStatsInCellCountLoB	Integer32
	atmSpvcVccStatsOutCellCountHiB	Integer32
	atmSpvcVccStatsOutCellCountLoB	Integer32
	atmSpvcVccStatsTimer	Integer32
	atmSpvcVccStatsFrwdErrCrrctnRateA2B	INTEGER
	atmSpvcVccStatsFrwdErrCrrctnRateB2A	INTEGER
	atmSpvcVccStatsInOdometerCellCountHiA	Integer32
	atmSpvcVccStatsInOdometerCellCountLoA	Integer32
	atmSpvcVccStatsOutOdometerCellCountHiA	Integer32
	atmSpvcVccStatsOutOdometerCellCountLoA	Integer32
	atmSpvcVccStatsInOdometerCellCountHiB	Integer32
	atmSpvcVccStatsInOdometerCellCountLoB	Integer32
	atmSpvcVccStatsOutOdometerCellCountHiB	Integer32
	atmSpvcVccStatsOutOdometerCellCountLoB	Integer32
	atmSpvcVccStatsOdometerTimer	Integer32
	atmSpvcVccStatsOdometerReset	INTEGER
	atmSpvcVccStatsCellsDroppedA	Integer32
	atmSpvcVccStatsCellsTaggedA	Integer32
	atmSpvcVccStatsCellsDroppedB	Integer32
	atmSpvcVccStatsCellsTaggedB	Integer32

AtmArpEntry
SEQUENCE
	atmArpIpAddress	IpAddress
	atmArpAtmAddress	OCTET STRING
	atmArpAddrType	INTEGER
	atmArpEntryState	INTEGER
	atmArpEntryRowStatus	RowStatus

AppIpRouteEntry
SEQUENCE
	appIpRouteDest	IpAddress
	appIpRouteMask	IpAddress
	appIpRouteMetric1	INTEGER
	appIpRouteNextHop	IpAddress
	appIpRouteState	INTEGER

IispCbrRoutEntry
SEQUENCE
	iispCbrRoutLength	Integer32
	iispCbrRoutNsapAddr	OCTET STRING
	iispCbrRoutIfIndex	IntfIndex
	iispCbrRoutRowStatus	RowStatus

IispVbrRoutEntry
SEQUENCE
	iispVbrRoutLength	Integer32
	iispVbrRoutNsapAddr	OCTET STRING
	iispVbrRoutIfIndex	IntfIndex
	iispVbrRoutRowStatus	RowStatus

IispCbrRouteEntry
SEQUENCE
	iispCbrRouteLength	Integer32
	iispCbrRouteNsapAddr	OCTET STRING
	iispCbrRouteIfIndex	IntfIndex
	iispCbrRouteRowStatus	RowStatus
	iispCbrRouteIfVuniId	INTEGER
	iispCbrRouteDest	Integer32
	iispCbrRouteType	Integer32

IispVbrRouteEntry
SEQUENCE
	iispVbrRouteLength	Integer32
	iispVbrRouteNsapAddr	OCTET STRING
	iispVbrRouteIfIndex	IntfIndex
	iispVbrRouteRowStatus	RowStatus
	iispVbrRouteIfVuniId	INTEGER
	iispVbrRouteDest	Integer32
	iispVbrRouteType	Integer32

FwReleaseEntry
SEQUENCE
	fwReleaseSlot	INTEGER
	fwReleaseRunning	OCTET STRING
	fwReleaseEpromVersion	OCTET STRING
	fwReleaseCurrentVersion	OCTET STRING
	fwReleaseNextVersion	OCTET STRING
	fwReleaseUpdate	INTEGER
	fwReleaseUpgrade	INTEGER

MsgPoolViewEntry
SEQUENCE
	msgPoolViewIndex	Integer32
	msgPoolViewTskId	Integer32
	msgPoolViewTskName	DisplayString
	msgPoolViewMsgCmd	Integer32

Arp1Entry
SEQUENCE
	arp1CardSlot	INTEGER
	arp1BridgeGroupNum	INTEGER
	arp1IpAddress	IpAddress
	arp1PhysicalAddr	OCTET STRING
	arp1EntryAge	Integer32

Arp2Entry
SEQUENCE
	arp2CardSlot	INTEGER
	arp2BridgeGroupNum	INTEGER
	arp2PhysicalAddr	OCTET STRING
	arp2IpAddress	IpAddress
	arp2EntryAge	Integer32

BridgeCacheEntry
SEQUENCE
	bridgeCacheCardSlot	INTEGER
	bridgeCacheBridgeGroupNum	INTEGER
	bridgeCachePhysicalAddr	OCTET STRING
	bridgeCacheType	INTEGER
	bridgeCacheSourcePort	INTEGER
	bridgeCacheEntryAge	Integer32

OamActDeactEntry
SEQUENCE
	oamActDeactIfB	IntfIndex
	oamActDeactVpiB	INTEGER
	oamActDeactVciB	INTEGER
	oamActDeactFuncType	INTEGER
	oamActDeactDirFlow	INTEGER
	oamActDeactFlowType	INTEGER
	oamActDeactBlkSizeAB	INTEGER
	oamActDeactBlkSizeBA	INTEGER
	oamActDeactStsSrcPointEteCC	INTEGER
	oamActDeactStsSnkPointEteCC	INTEGER
	oamActDeactRsltPrevReq	INTEGER
	oamActDeactRowStatus	RowStatus
	oamActDeactStsSrcPointEtePM	INTEGER
	oamActDeactStsSnkPointEtePM	INTEGER
	oamActDeactStsSrcPointEtePMBR	INTEGER
	oamActDeactStsSnkPointEtePMBR	INTEGER
	oamActDeactBRBlockError	INTEGER
	oamActDeactBRLostInsertedCell	INTEGER
	oamActDeactBRMisInsertedCell	INTEGER
	oamActDeactStsSrcPointSegPM	INTEGER
	oamActDeactStsSnkPointSegPM	INTEGER
	oamActDeactStsSrcPointSegPMBR	INTEGER
	oamActDeactStsSnkPointSegPMBR	INTEGER
	oamActDeactStsSrcPointSegCC	INTEGER
	oamActDeactStsSnkPointSegCC	INTEGER

OamLoopbackEntry
SEQUENCE
	oamLpbkIfB	IntfIndex
	oamLpbkVpiB	INTEGER
	oamLpbkVciB	INTEGER
	oamLoopbackType	INTEGER
	oamLpbkLocationID	OCTET STRING
	oamLpbkAction	INTEGER
	oamLpbkStatus	INTEGER
	oamLpbkTxCount	Integer32
	oamLpbkRxCount	Integer32
	oamLpbkMismatchCount	Integer32
	oamLpbkTimeout	INTEGER

ViprRouterConfigEntry
SEQUENCE
	viprSlot	Integer32
	viprRouterId	INTEGER
	viprRouterName	DisplayString
	viprRouterNoOfInterfaces	INTEGER
	viprRouterNoOfRoutes	INTEGER
	viprRouterAdminStatus	INTEGER
	viprRouterOperStatus	INTEGER
	viprRouterInitTmr	Integer32
	viprRouterDisabWarnTmr	Integer32
	viprRouterShutDwnWarnTmr	Integer32
	viprRouterDisableWarning	INTEGER
	viprRouterDisableReason	INTEGER
	viprRouterRowStatus	RowStatus

ViprIntfConfigEntry
SEQUENCE
	viprIntfId	Integer32
	viprIntfIPAddress	IpAddress
	viprIntfIPNetMask	IpAddress
	viprIntfAdminStatus	INTEGER
	viprIntfOperStatus	INTEGER
	viprIntfInitTmr	Integer32
	viprIntfDisabWarnTmr	Integer32
	viprIntfShutDwnWarnTmr	Integer32
	viprIntfDisableWarning	INTEGER
	viprIntfDisableReason	INTEGER
	viprIntfRipVersion	INTEGER
	viprIntfRipMode	INTEGER
	viprIntfRowStatus	RowStatus
	viprIntfRipLineType	INTEGER
	viprIntfAuthPasswd	DisplayString

ViprSubChnlConfigEntry
SEQUENCE
	viprSubChnlId	Integer32
	viprSubChnlIntfIndex	IntfIndex
	viprSubChnlTrafficType	INTEGER
	viprSubChnlLlcEncapType	INTEGER
	viprSubChnlMacEncapType	INTEGER
	viprSubChnlTosFeature	INTEGER
	viprSubChnlTosValue	INTEGER
	viprSubChnlTosMask	INTEGER
	viprSubChnlVpiDlci	INTEGER
	viprSubChnlVci	INTEGER
	viprSubChnlSarType	INTEGER
	viprSubChnlServiceType	INTEGER
	viprSubChnlFwdErrCorrection	INTEGER
	viprSubChnlInterworkingType	INTEGER
	viprSubChnlFrameSize	Integer32
	viprSubChnlComBurstSize	Integer32
	viprSubChnlExcessBurstSize	Integer32
	viprSubChnlCommitedInfoRate	Integer32
	viprSubChnlTimeInterval	INTEGER
	viprSubChnlAtmPeakCellRate	Integer32
	viprSubChnlAtmSustainedCellRate	Integer32
	viprSubChnlAtmMaxBurstSize	Integer32
	viprSubChnlFrPeakCellRate	Integer32
	viprSubChnlFrSustainedCellRate	Integer32
	viprSubChnlFrMaxBurstSize	Integer32
	viprSubChnlFlowType	INTEGER
	viprSubChnlAdminStatus	INTEGER
	viprSubChnlOperStatus	INTEGER
	viprSubChnlInitTmr	Integer32
	viprSubChnlDisabWarnTmr	Integer32
	viprSubChnlShutDwnWarnTmr	Integer32
	viprSubChnlDisableWarning	INTEGER
	viprSubChnlDisableReason	INTEGER
	viprSubChnlRowStatus	RowStatus
	viprSubChnlImIpAddr	IpAddress
	viprSubChnlImMask	IpAddress
	viprSubChnlViB	INTEGER
	viprSubChnlVUNIB	INTEGER
	viprSubChnlTrafficShaping	INTEGER
	viprSubChnlAtmOamStatus	INTEGER

ViprRouteConfigEntry
SEQUENCE
	viprRouteId	Integer32
	viprRouteIPAddress	IpAddress
	viprRouteIPNetMask	IpAddress
	viprRouteDestAddress	IpAddress
	viprRouteGatewayAddress	IpAddress
	viprRouteServiceType	INTEGER
	viprRouteMetric	Integer32
	viprRouteAdminStatus	INTEGER
	viprRouteOperStatus	INTEGER
	viprRouteInitTmr	Integer32
	viprRouteDisabWarnTmr	Integer32
	viprRouteShutDwnWarnTmr	Integer32
	viprRouteDisableWarning	INTEGER
	viprRouteDisableReason	INTEGER
	viprRouteRowStatus	RowStatus
	viprRouteDestMask	IpAddress

ViprRoutingConfigEntry
SEQUENCE
	viprRoutingCommand	INTEGER
	viprRoutingIPAddress	IpAddress
	viprRoutingIPNetMask	IpAddress
	viprRoutingDestAddress	IpAddress
	viprRoutingGatewayAddress	IpAddress
	viprRoutingServiceType	INTEGER
	viprRoutingType	INTEGER
	viprRoutingMetric	Integer32
	viprRoutingDestMask	IpAddress
	viprRoutingAge	Integer32
	viprRoutingIndex	Integer32

ViprArpConfigEntry
SEQUENCE
	viprArpCommand	INTEGER
	viprArpIPAddress	IpAddress
	viprArpHwAddress	OCTET STRING
	viprArpEntryAge	Integer32
	viprArpInterfaceIPAddress	IpAddress
	viprArpInterfaceIPMask	IpAddress
	viprArpInterfaceServiceType	INTEGER
	viprArpIndex	Integer32

ViprPingConfigEntry
SEQUENCE
	ipAddr	IpAddress
	pingStatus	INTEGER

ViprRipConfigEntry
SEQUENCE
	viprRipUpdateInt	INTEGER

ViprVpnStatsEntry
SEQUENCE
	viprVpnStatsTimer	Integer32
	viprVpnStatsIcmpOutEchoRPs	Integer32
	viprVpnStatsIcmpOutDestURs	Integer32
	viprVpnStatsIcmpOutSrcQ	Integer32
	viprVpnStatsIcmpOutRedirects	Integer32
	viprVpnStatsIcmpOutEchoRQs	Integer32
	viprVpnStatsIcmpOutTimeXs	Integer32
	viprVpnStatsIcmpOutParamps	Integer32
	viprVpnStatsIcmpOutTimeRQs	Integer32
	viprVpnStatsIcmpOutTimeRPs	Integer32
	viprVpnStatsIcmpOutInfoRQs	Integer32
	viprVpnStatsIcmpOutInfoRPs	Integer32
	viprVpnStatsIcmpOutMaskRQs	Integer32
	viprVpnStatsIcmpOutMaskRPs	Integer32
	viprVpnStatsIcmpOutErrors	Integer32
	viprVpnStatsIcmpInErrors	Integer32
	viprVpnStatsIcmpInEchoRQs	Integer32
	viprVpnStatsIcmpInAddrMasks	Integer32
	viprVpnStatsIcmpInAddrMaskReps	Integer32
	viprVpnStatsIcmpInEchoReps	Integer32
	viprVpnStatsIcmpInDestUnreachs	Integer32
	viprVpnStatsIcmpInSrcQuenchs	Integer32
	viprVpnStatsIcmpInTimeExcds	Integer32
	viprVpnStatsIcmpInParamProbs	Integer32
	viprVpnStatsIcmpInTimeStamps	Integer32
	viprVpnStatsIcmpInTimeStampsReps	Integer32

ViprStatsEntry
SEQUENCE
	viprStatsReset	INTEGER
	viprStatsPacketsRxHi	Integer32
	viprStatsPacketsRxLo	Integer32
	viprStatsPacketsTxHi	Integer32
	viprStatsPacketsTxLo	Integer32
	viprStatsMismatchCrcHi	Integer32
	viprStatsMismatchCrcLo	Integer32
	viprStatsInsufficientPcktsHi	Integer32
	viprStatsInsufficientPcktsLo	Integer32
	viprStatsExceedAal5CellsHi	Integer32
	viprStatsExceedAal5CellsLo	Integer32
	viprStatsPrototypeErrorsHi	Integer32
	viprStatsPrototypeErrorsLo	Integer32
	viprStatsArpProtoRxHi	Integer32
	viprStatsArpProtoRxLo	Integer32
	viprStatsIPInHdrErrorsHi	Integer32
	viprStatsIPInHdrErrorsLo	Integer32
	viprStatsIPInAddrErrorsHi	Integer32
	viprStatsIPInAddrErrorsLo	Integer32

ViprSubChnlStatsEntry
SEQUENCE
	viprSubChnlStatsInCellCountHiA	Integer32
	viprSubChnlStatsInCellCountLoA	Integer32
	viprSubChnlStatsOutCellCountHiA	Integer32
	viprSubChnlStatsOutCellCountLoA	Integer32
	viprSubChnlStatsInCellCountHiB	Integer32
	viprSubChnlStatsInCellCountLoB	Integer32
	viprSubChnlStatsOutCellCountHiB	Integer32
	viprSubChnlStatsOutCellCountLoB	Integer32
	viprSubChnlStatsTimer	Integer32
	viprSubChnlStatsInOdometerCellCountHiA	Integer32
	viprSubChnlStatsInOdometerCellCountLoA	Integer32
	viprSubChnlStatsOutOdometerCellCountHiA	Integer32
	viprSubChnlStatsOutOdometerCellCountLoA	Integer32
	viprSubChnlStatsInOdometerCellCountHiB	Integer32
	viprSubChnlStatsInOdometerCellCountLoB	Integer32
	viprSubChnlStatsOutOdometerCellCountHiB	Integer32
	viprSubChnlStatsOutOdometerCellCountLoB	Integer32
	viprSubChnlStatsOdometerTimer	Integer32
	viprSubChnlStatsOdometerReset	INTEGER
	viprSubChnlStatsCellsDroppedB	Integer32
	viprSubChnlStatsCellsTaggedB	Integer32

VirtualIntfStatsEntry
SEQUENCE
	virtualIntfStatsIf	IntfIndex
	virtualIntfStatsVi	INTEGER
	virtualIntfStatsEgrCellCount	Integer32
	virtualIntfStatsTimer	Integer32
	virtualIntfStatsReset	INTEGER

CardFwVerEntry
SEQUENCE
	cardFwVerSlot	INTEGER
	cardFwVerType	Integer32
	cardFwVerCurrent	OCTET STRING
	cardFwVerCurrentIsDefault	Integer32
	cardFwVerNext	OCTET STRING
	cardFwVerNextIsDefault	INTEGER
	cardFwDnldStatus	INTEGER
	cardFwRetries	Integer32

FwDriverEntry
SEQUENCE
	fwSlotId	Integer32
	fwDriverType	Integer32
	fwIsDefault	Integer32
	fwDriverName	OCTET STRING
	fwDriverFrn	Integer32
	fwDriverSize	Integer32
	fwDriverChecksum	Integer32

AtmTrunkingRemoteIWFEntry
SEQUENCE
	atmTrunkingRemoteIWFIdentifier	Integer32
	atmTrunkingRemoteIWFAddress	OCTET STRING
	atmTrunkingRemoteIWFTrnkMode	INTEGER
	atmTrunkingRemoteIWFAdminStatus	INTEGER
	atmTrunkingRemoteIWFRowStatus	RowStatus

AtmTrunkingSigVccEntry
SEQUENCE
	atmTrunkingSigVccRmtIWFIdentifier	Integer32
	atmTrunkingSigVccIdentifier	INTEGER
	atmTrunkingSigVccOutgoingIfIndex	IntfIndex
	atmTrunkingSigVccOutgoingVpi	INTEGER
	atmTrunkingSigVccOutgoingVci	INTEGER
	atmTrunkingSigVccOwner	INTEGER
	atmTrunkingSigVccInactiveTimer	Integer32
	atmTrunkingSigVccType	INTEGER
	atmTrunkingSigVccSignaling	INTEGER
	atmTrunkingSigVccFwPcr01	Integer32
	atmTrunkingSigVccBwPcr01	Integer32
	atmTrunkingSigVccFwScr01	Integer32
	atmTrunkingSigVccBwScr01	Integer32
	atmTrunkingSigVccFwMbs01	Integer32
	atmTrunkingSigVccBwMbs01	Integer32
	atmTrunkingSigVccMaxAal2Vcc	Integer32
	atmTrunkingSigVccActiveAal2Vcc	Integer32
	atmTrunkingSigVccOperStatus	Integer32
	atmTrunkingSigVccRowStatus	RowStatus
	atmTrunkingSigVccViB	INTEGER
	atmTrunkingSigVccVUNIB	INTEGER
	atmTrunkingSigVccRetryTimer	Integer32
	atmTrunkingSigVccRetryLimit	Integer32
	atmTrunkingSigVccRestart	INTEGER
	atmTrunkingSigVccPriority	INTEGER
	atmTrunkingSigVccRetryCounter	Integer32

AtmTrunkingBrVccConfigEntry
SEQUENCE
	atmTrunkingBrVccRmtIWFId	Integer32
	atmTrunkingBrVccSigVccId	INTEGER
	atmTrunkingBrVccId	INTEGER
	atmTrunkingBrVccIf	IntfIndex
	atmTrunkingBrVccVpi	INTEGER
	atmTrunkingBrVccVci	INTEGER
	atmTrunkingBrVccViB	INTEGER
	atmTrunkingBrVccVUNIB	INTEGER
	atmTrunkingBrVccServiceType	INTEGER
	atmTrunkingBrVccSarType	INTEGER
	atmTrunkingBrVccOwner	INTEGER
	atmTrunkingBrVccOperStatus	INTEGER
	atmTrunkingBrVccFwAtmPcr01	Integer32
	atmTrunkingBrVccBwAtmPcr01	Integer32
	atmTrunkingBrVccFwAtmScr01	Integer32
	atmTrunkingBrVccBwAtmScr01	Integer32
	atmTrunkingBrVccFwAtmMbs01	Integer32
	atmTrunkingBrVccBwAtmMbs01	Integer32
	atmTrunkingBrVccConnType	INTEGER
	atmTrunkingBrVccActiveChanCnt	Integer32
	atmTrunkingBrVccMaxAal2ChanId	Integer32
	atmTrunkingBrVccCircuitModeDataSupp	INTEGER
	atmTrunkingBrVccFrameModeSupp	INTEGER
	atmTrunkingBrVccFaxModSupp	INTEGER
	atmTrunkingBrVccCASPktXportSupp	INTEGER
	atmTrunkingBrVccDTMFPktXportSupp	INTEGER
	atmTrunkingBrVccMFR1PktXportSupp	INTEGER
	atmTrunkingBrVccMFR2PktXportSupp	INTEGER
	atmTrunkingBrVccPCMEncoding	INTEGER
	atmTrunkingBrVccMaxFrameLength	INTEGER
	atmTrunkingBrVccIdleChannSuprSupp	INTEGER
	atmTrunkingBrVccSilenceDetSupp	INTEGER
	atmTrunkingBrVccCompressionSpec	INTEGER
	atmTrunkingBrVccAudioProfileSource	INTEGER
	atmTrunkingBrVccAudioProfileId	INTEGER
	atmTrunkingBrVccAvailBw	INTEGER
	atmTrunkingBrVccRowStatus	RowStatus
	atmTrunkingBrVccGr303Supp	INTEGER
	atmTrunkingBrVccOamStatus	INTEGER
	atmTrunkingBrVccInactiveTimer	Integer32
	atmTrunkingBrVccRetryTimer	Integer32
	atmTrunkingBrVccRetryLimit	Integer32
	atmTrunkingBrVccRestart	INTEGER
	atmTrunkingBrVccCuTimer	INTEGER
	atmTrunkingBrVccPriority	INTEGER
	atmTrunkingBrVccRetryCounter	Integer32

AtmTrunkingDataChannelConfigEntry
SEQUENCE
	atmTrunkingDataChannelRmtIWFId	Integer32
	atmTrunkingDataChannelSigVccId	INTEGER
	atmTrunkingDataChannelBrVccId	INTEGER
	atmTrunkingDataChannelId	INTEGER
	atmTrunkingDataChanOperStatus	INTEGER
	atmTrunkingDataChanOwner	INTEGER
	atmTrunkingDataChanNBIntf	IntfIndex

H248TermIdEntry
SEQUENCE
	h248TermSlotId	INTEGER
	h248TermPhyPortId	INTEGER
	h248TermLogPortId	INTEGER
	h248TermChanId	INTEGER
	h248TermVpi	INTEGER
	h248TermVci	INTEGER
	h248TermId	OCTET STRING
	h248TermAal2Cid	INTEGER
	h248TermActivation	INTEGER
	h248TermRowStatus	RowStatus

ProtectionGroupEntry
SEQUENCE
	pgtGroupId	Integer32
	pgtSwitchoverMethod	INTEGER
	pgtSwitchbackMethod	INTEGER
	pgtStandbySelection	INTEGER
	pgtRowStatus	RowStatus

InterfaceProtectionEntry
SEQUENCE
	iptGroupId	Integer32
	iptLogicalIntfId	Integer32
	iptPhysicalIntfId	Integer32
	iptOperState	INTEGER
	iptIntfType	INTEGER
	iptOperatingIntf	Integer32
	iptProtCommand	INTEGER
	iptSelectedStandby	Integer32
	iptRowStatus	RowStatus

Defined Values

lucent		3.1.1751
OBJECT IDENTIFIER

mibs		3.1.1751.2
OBJECT IDENTIFIER

acMIB		3.1.1751.2.18
Lucent Access Concentrator, Release 6.2
MODULE-IDENTITY

sysConfig		3.1.1751.2.18.1
OBJECT IDENTIFIER

equipConfig		3.1.1751.2.18.2
OBJECT IDENTIFIER

channelConfig		3.1.1751.2.18.3
OBJECT IDENTIFIER

intfConfig		3.1.1751.2.18.5
OBJECT IDENTIFIER

connectionConfig		3.1.1751.2.18.6
OBJECT IDENTIFIER

userServiceConfig		3.1.1751.2.18.7
OBJECT IDENTIFIER

sysTraps		3.1.1751.2.18.8
OBJECT IDENTIFIER

systemEvents		3.1.1751.2.18.8.1
OBJECT IDENTIFIER

moduleEvents		3.1.1751.2.18.8.2
OBJECT IDENTIFIER

interfaceEvents		3.1.1751.2.18.8.3
OBJECT IDENTIFIER

connectionEvents		3.1.1751.2.18.8.4
OBJECT IDENTIFIER

sysStatistics		3.1.1751.2.18.9
OBJECT IDENTIFIER

equipStatistics		3.1.1751.2.18.10
OBJECT IDENTIFIER

intfStatistics		3.1.1751.2.18.11
OBJECT IDENTIFIER

connectionStatistics		3.1.1751.2.18.12
OBJECT IDENTIFIER

ipAtmGroup		3.1.1751.2.18.13
OBJECT IDENTIFIER

iispRouting		3.1.1751.2.18.14
OBJECT IDENTIFIER

returnCode		3.1.1751.2.18.15
OBJECT IDENTIFIER

sysControl		3.1.1751.2.18.16
OBJECT IDENTIFIER

stratumConfig		3.1.1751.2.18.17
OBJECT IDENTIFIER

cellTest		3.1.1751.2.18.18
OBJECT IDENTIFIER

sysInfo		3.1.1751.2.18.19
OBJECT IDENTIFIER

ethernetConfig		3.1.1751.2.18.20
OBJECT IDENTIFIER

alarmConfig		3.1.1751.2.18.21
OBJECT IDENTIFIER

sysTest		3.1.1751.2.18.22
OBJECT IDENTIFIER

fwDriverSup		3.1.1751.2.18.23
OBJECT IDENTIFIER

viprConfig		3.1.1751.2.18.24
OBJECT IDENTIFIER

toneAnnceControl		3.1.1751.2.18.25
OBJECT IDENTIFIER

gr303Config		3.1.1751.2.18.26
OBJECT IDENTIFIER

gr303Stats		3.1.1751.2.18.27
OBJECT IDENTIFIER

atmTrunkingMIBObjects		3.1.1751.2.18.28
OBJECT IDENTIFIER

protectionGroup		3.1.1751.2.18.29
OBJECT IDENTIFIER

h248Config		3.1.1751.2.18.30
OBJECT IDENTIFIER

h248SysControl		3.1.1751.2.18.31
OBJECT IDENTIFIER

siteName		3.1.1751.2.18.1.1
site name - ascii
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

siteID		3.1.1751.2.18.1.2
site id - numerical
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

siteEtherIpAddr		3.1.1751.2.18.1.3
ip address for ethernet access to the site (switch)
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

siteEtherIpMask		3.1.1751.2.18.1.4
ip mask for ethernet access to the site (switch)
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

siteGatewayAddr		3.1.1751.2.18.1.5
ip address for gateway access to the site (switch)
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

siteAtmAddrPrefix1		3.1.1751.2.18.1.6
This is one of the two atm address prefix of this switch.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(13)

siteAtmAddrUser1		3.1.1751.2.18.1.7
This is one of the two atm address user part of this switch.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(7)

siteRemoteMgrAddr1		3.1.1751.2.18.1.8
remote manager IP Address, where TRAP will be sent to.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

siteRemoteMgrAddr2		3.1.1751.2.18.1.9
remote manager IP Address, where TRAP will be sent to.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

siteRemoteMgrAddr3		3.1.1751.2.18.1.10
remote manager IP Address, where TRAP will be sent to.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

siteRemoteMgrAddr4		3.1.1751.2.18.1.11
remote manager IP Address, where TRAP will be sent to.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

siteRemoteMgrAddr5		3.1.1751.2.18.1.12
remote manager IP Address, where TRAP will be sent to.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

siteMasterNodeAtmAddr1		3.1.1751.2.18.1.13
Master node atm address, where TRAP will be sent to.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(20)

siteMasterNodeAtmAddr2		3.1.1751.2.18.1.14
Master node atm address, where TRAP will be sent to.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(20)

siteEnhanceFeatures		3.1.1751.2.18.1.15
enhancement features capability - number consists of a sum to represent the following: 1: securedAtm 2: isdn 4: frameRelay
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

siteTrapDialOutFeature		3.1.1751.2.18.1.16
Enables the dialing out to a remote terminal or beeper for trap notification.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), dialTerminal(2), dialBeeper(3)

siteTrapDialOutPhoneNum		3.1.1751.2.18.1.17
Phone number of the terminal to dial when trap notifications are phoned out
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

siteTrapDialOutBeeperData		3.1.1751.2.18.1.18
Data (phone digits) to send to beeper if the dialBeeper option is selected.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

siteDateAndTime		3.1.1751.2.18.1.19
Current date and time: 11 octets octet# contents range ------ -------- ----- 1-2 year 0..65536 3 month 1..12 4 day 1..31 5 hour 0..23 6 minutes 0..59 7 seconds 0..60(60=leap second) 8 deci-seconds 0..9 9 direction from UTC '+'/'-' 10 hours from UTC 0..11 11 minutes from UTC 0..59
Status: current	Access: read-write
OBJECT-TYPE
	DateAndTime

siteSoftwareVersion		3.1.1751.2.18.1.20
Constant value representing the version number of the current software.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(15)

csTcpServerIpAddress		3.1.1751.2.18.1.21
The IP address of CS
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

csTcpServerPortNumber		3.1.1751.2.18.1.22
The Port Number used for communication with CS. NOTE: Port # 5000 and 6000 have been reservered for AC products. DO NOT USED THEM !!!
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1025..65535

keepAliveTimer		3.1.1751.2.18.1.23
keep alive timer can be set inbetween 0 and 999999999
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..999999999

inactiveTimer		3.1.1751.2.18.1.24
inactive timer can be set inbetween 0 and 999999999
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..999999999

siteMasterNodeAddrType1		3.1.1751.2.18.1.25
Type of address specified for master node atm address, where TRAP will be sent to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nsap(1), e164(2), e164nsap(3)

siteMasterNodeAddrType2		3.1.1751.2.18.1.26
Type of address specified for master node atm address, where TRAP will be sent to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nsap(1), e164(2), e164nsap(3)

inBandPrimaryIpAddress		3.1.1751.2.18.1.27
IP address of the switch when the switch is accessed over the primary in-band connection.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

inBandPrimaryIpMask		3.1.1751.2.18.1.28
IP address subnet mask of the primary in-band management IP address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

inBandBackupIpAddress		3.1.1751.2.18.1.29
IP address of the switch when the switch is accessed over the secondary in-band connection.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

inBandBackupIpMask		3.1.1751.2.18.1.30
IP address subnet mask of the secondary in-band management IP address.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

inBandSvcConnectionsAllowed		3.1.1751.2.18.1.31
Flag indicating whether in-band management should be supported over SVCs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmArpServer		3.1.1751.2.18.1.32
This flag indicates if this switch is an ATM ARP server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmArpServerRemoteConnectionType		3.1.1751.2.18.1.33
When this switch is not the ATM ARP server, indicates whether the connection to the ATM ARP server uses SVCs or PVCs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	svc(1), pvc(2)

atmArpServerRemoteAtmAddress		3.1.1751.2.18.1.34
The ATM address of the ATM ARP server when this switch is not the ATM ARP server and the connection to the ATM ARP server uses SVCs.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(20)

atmArpServerRemoteAddrType		3.1.1751.2.18.1.35
The format of the ATM address of the ATM ARP server when this switch is not the ATM ARP server and the connection to the ATM ARP server uses SVCs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nsap(1), e164(2), e164nsap(3)

atmArpServerRemoteIpAddress		3.1.1751.2.18.1.36
The IP address of the ATM ARP server when this switch is not the ATM ARP server and the connection to the ATM ARP server uses PVCs.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

atmArpServerRemoteIpMask		3.1.1751.2.18.1.37
The IP address subnet mask of the ATM ARP server when this switch is not the ATM ARP server and the connection to the ATM ARP server uses PVCs.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

atmArpServerEncapsulation		3.1.1751.2.18.1.38
The type of encapsulation used for IP packets over ATM in in-band management.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	llc-snap(1)

siteFallbackSoftwareVersion		3.1.1751.2.18.1.41
Constant value representing the version number of the software to fallback to.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(15)

siteUpgradeSoftwareVersion		3.1.1751.2.18.1.42
Constant value representing the version number of the software to upgrade to.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(15)

siteSwitchIpAddr		3.1.1751.2.18.1.43
IP Address for communication with the switch, regardless of which cpu is primary.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

muxTcpType		3.1.1751.2.18.1.44
The type of mux TCP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	server(1), client(2)

loopbackLocationID		3.1.1751.2.18.1.45
ID of the ATM Node where the loopback is to occur.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(16)

oamDebouncingPeriod		3.1.1751.2.18.1.46
Debouncing period in milli seconds for clearing AIS/RDI state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1000..300000

svcPointToPointCalls		3.1.1751.2.18.1.47
The total number of SVC point-to-point calls, both legs are SVCs.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

svcPointToMultiPointCalls		3.1.1751.2.18.1.48
The total number of SVC point-to-multipoint calls, both legs are SVCs.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

svcPointToMultiPointParties		3.1.1751.2.18.1.49
The total number of parties on SVC point-to-multipoint calls, both legs are SVCs.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

spvcCePointToPointCalls		3.1.1751.2.18.1.50
The total number of circuit emulation SPVC calls.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

spvcTePointToPointCalls		3.1.1751.2.18.1.51
The total number of terminal emulation SPVC calls.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

spvcAtmPointToPointCalls		3.1.1751.2.18.1.52
The total number of ATM SPVC calls.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

cgApiCirEmCirEmPvcCalls		3.1.1751.2.18.1.53
The total number of circuit emulation to circuit emulation calls for Sapphire API.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

cgApiCirEmAtmPvcCalls		3.1.1751.2.18.1.54
The total number of circuit emulation to ATM calls for Sapphire APIs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

cgApiAtmAtmPvcCalls		3.1.1751.2.18.1.55
The total number of ATM to ATM calls for Sapphire APIs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

cgApiPointToPointSvcCalls		3.1.1751.2.18.1.56
The total number of point-to-point SVC calls for Sapphire APIs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

cgApiPointToMultiPointSvcCalls		3.1.1751.2.18.1.57
The total number of point-to-multipoint SVC calls for Sapphire APIs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

cgApiPointToMultiPointParties		3.1.1751.2.18.1.58
The total number of parties for Sapphire APIs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

callContrlResAllocApply		3.1.1751.2.18.1.59
0 - not apply, 1 - apply the call control resouce allocation modification
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1

callContrlResAllocUsage		3.1.1751.2.18.1.60
The percentage of memory usage for call control resource.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

siteFirmwarePatchNumber		3.1.1751.2.18.1.61
Constant value representing the patch number of the patch release.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

spvcActRestartAll		3.1.1751.2.18.1.62
Restart all ATM-to-ATM,CE-to-CE,TE-to-TE,FR-to-FR active unconnected spvc connections
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	spvcActAtmRestartAll(1), spvcActCeRestartAll(2), spvcActTeRestartAll(3), spvcActFrRestartAll(4)

cgSvcCutThroughOption		3.1.1751.2.18.1.63
Cut Through option for SVC calls going to CG cgSvcAcImplicitCutThrough (1) - AC implicitly cuts through. cgSvcCgExplicitCutThrough (2) - CG sends explcit PATH_ETABLISH_REQ to request AC to cut through.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cgSvcAcImplicitCutThrough(1), cgSvcCgExplicitCutThrough(2)

sgApiCirEmEndPoints		3.1.1751.2.18.1.64
The total number of circuit emulation endpoints for Sapphire API.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

sgApiAtmSvcEndPoints		3.1.1751.2.18.1.65
The total number of ATM SVC endpoints for Sapphire APIs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

siteRemoteMgrSrcAddr1		3.1.1751.2.18.1.66
This is the source IP address used in all traps sent to remote manager
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ethernet(1), ibm(2), interface(3)

siteRemoteMgrSrcAddr2		3.1.1751.2.18.1.67
This is the source IP address used in all traps sent to remote manager
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ethernet(1), ibm(2), interface(3)

siteRemoteMgrSrcAddr3		3.1.1751.2.18.1.68
This is the source IP address used in all traps sent to remote manager
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ethernet(1), ibm(2), interface(3)

siteRemoteMgrSrcAddr4		3.1.1751.2.18.1.69
This is the source IP address used in all traps sent to remote manager
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ethernet(1), ibm(2), interface(3)

siteRemoteMgrSrcAddr5		3.1.1751.2.18.1.70
This is the source IP address used in all traps sent to remote manager
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ethernet(1), ibm(2), interface(3)

spvcFrPointToPointCalls		3.1.1751.2.18.1.71
The total number of FR SPVC calls.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

inBandAppAtmAddress		3.1.1751.2.18.1.72
The ATM address of the inBand application
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(20)

inBandAppAtmAddrType		3.1.1751.2.18.1.73
The format of the ATM address of the inBand application
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nsap(1), e164(2), e164nsap(3)

atmArpServer2RemoteAtmAddress		3.1.1751.2.18.1.74
The ATM address of the ATM ARP server when this switch is not the ATM ARP server and the connection to the ATM ARP server uses SVCs.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(20)

atmArpServer2RemoteAddrType		3.1.1751.2.18.1.75
The format of the ATM address of the ATM ARP server when this switch is not the ATM ARP server and the connection to the ATM ARP server uses SVCs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nsap(1), e164(2), e164nsap(3)

tasmMaxAnnceDiskSpace		3.1.1751.2.18.1.76
Specifies the maximum disk size in MBytes reserved for compressed announcements on the CPU hard disk.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..36

tasmMaxAnnce		3.1.1751.2.18.1.77
Specifies the maximum number of tones and announcements that can be played simultaneously. This will depend on the number of control blocks allocated for collecting digits and for line tests as the memory comes from the same pool. The tasmControlBlockResAllocUsage field will be updated to indicate this.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10000

tasmMaxStdTones		3.1.1751.2.18.1.78
Specifies the maximum number of tones that can be played simutaneously. This field has been obsoleted for optimisation of resources.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

tasmMemoryAction		3.1.1751.2.18.1.79
Specifies the action to be performed on the memory in the TASM card used for storing announcements.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	re-initialize(1)

tasAnnceTable		3.1.1751.2.18.1.80
Table of announcements for the Tone Announcement server .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TasAnnceEntry

tasAnnceEntry		3.1.1751.2.18.1.80.1
Row definition for Tone Announcement server table announcement entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	TasAnnceEntry

tasAnnceId		3.1.1751.2.18.1.80.1.1
Announcement ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..100

tasAnnceType		3.1.1751.2.18.1.80.1.2
The type of this announcement: voice indicates it is a pure voice announcement file. toneVoice indicates it is a file with tones at the beginning followed by voice. userTones indicates it is a file with purely user generated tones. music indicates it is a file with pure music. musicVoice indicates it is a file with music at the beginning followed by voice. toneMusic indicates it is a file with tones at the beginning followed by music.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	voice(1), toneVoice(2), userTones(3), music(4), musicVoice(5), toneMusic(6)

tasAnnceCmprsType		3.1.1751.2.18.1.80.1.3
The type of compression used for storing this announcement: compress8k indicates 8k compression algorithm should be used. compress16k indicates 16k compression algorithm should be used. compress32k indicates 32k compression algorithm should be used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	uncompressed(1), compress8k(2), compress16k(3), compress32k(4)

tasAnnceValid		3.1.1751.2.18.1.80.1.4
Indicates the condition of this announcement, whether it is good, it is stored using an older compression algorithm, or it is corrupted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	good(1), olderVersion(2), corrupted(3)

tasAnnceDescription		3.1.1751.2.18.1.80.1.5
Description for this announcement.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(255)

tasToneConfigTable		3.1.1751.2.18.1.81
Table of standard physical tone attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TasToneConfigEntry

tasToneConfigEntry		3.1.1751.2.18.1.81.1
Row definition for TASM announcement entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	TasToneConfigEntry

tasToneId		3.1.1751.2.18.1.81.1.1
Tone ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10

tasToneType		3.1.1751.2.18.1.81.1.2
The type of this standard tone.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dialTone(1), reorderTone(2), sitTone(3)

tasToneFirstFreq		3.1.1751.2.18.1.81.1.3
The first frequency value for this tone.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

tasToneSecondFreq		3.1.1751.2.18.1.81.1.4
The second frequency value for this tone.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

tasToneThirdFreq		3.1.1751.2.18.1.81.1.5
The third frequency value for this tone.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

tasToneOnTime		3.1.1751.2.18.1.81.1.6
The on time in the tone duty cycle.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

tasToneOffTime		3.1.1751.2.18.1.81.1.7
The off time in the tone duty cycle.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

tasToneLevel		3.1.1751.2.18.1.81.1.8
The level of this tone in dBm.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmArpServerAtmAddr		3.1.1751.2.18.1.82
The ATM address of the ATM ARP server when this switch is configured as the ATM ARP server .
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(20)

atmArpServerAddrType		3.1.1751.2.18.1.83
The format of the ATM address of the ATM ARP server when this switch is configured as the ATM ARP server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nsap(1), e164(2), e164nsap(3)

spvcPointToMultiPointCalls		3.1.1751.2.18.1.84
The total number of SPVC point-to-multipoint calls
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

spvcPointToMultiPointParties		3.1.1751.2.18.1.85
The total number of parties on SPVC point-to-multipoint calls.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

consoleIPAddr1		3.1.1751.2.18.1.86
console IP Address, where TRAP will be sent.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

consoleIPAddr2		3.1.1751.2.18.1.87
console IP Address, where TRAP will be sent.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

consoleIPAddr3		3.1.1751.2.18.1.88
console IP Address, where TRAP will be sent.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

consolePort1		3.1.1751.2.18.1.89
port number on host where TRAP will be sent
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..32767

consolePort2		3.1.1751.2.18.1.90
port number on host where TRAP will be sent
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..32767

consolePort3		3.1.1751.2.18.1.91
port number on host where TRAP will be sent
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..32767

featureTable		3.1.1751.2.18.1.92
Table of features to be turned on/off
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FeatureEntry

featureEntry		3.1.1751.2.18.1.92.1
Row definition for feature table
Status: current	Access: not-accessible
OBJECT-TYPE
	FeatureEntry

featureId		3.1.1751.2.18.1.92.1.1
feature ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	pnni(1), gr303(2), vipr(3), h248(4)

featureStaticMem		3.1.1751.2.18.1.92.1.2
Minimum memory required to run this feature
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

featureDesiredStatus		3.1.1751.2.18.1.92.1.3
To enable / disable this feature
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

featureCurrentStatus		3.1.1751.2.18.1.92.1.4
This feature is enabled / disabled
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

mediaGatewayControlType		3.1.1751.2.18.1.93
Choose to use H.248 protocol or sapphire protocol
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sapphire(1), h248(2)

dspResourceTable		3.1.1751.2.18.1.94
Table of DSP resource usage for the whole system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DspResourceEntry

dspResourceEntry		3.1.1751.2.18.1.94.1
Row definition for DSP resource usage table entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	DspResourceEntry

dspResourceId		3.1.1751.2.18.1.94.1.1
DSP resource type enumerations. The algoSets describe the mode of the DSP card. Each mode corresponds to a set of algorithms supported by the IO card. Aal modes describe the aal type used. algoSet1-aal2-non-multiplexed: resource type for algoSet1 DSP mode and non-multiplexed aal2 AAL mode. algoSet1-aal2-std : resource type for algoSet1 DSP mode and standard aal2 AAL mode. algoSet2-aal2-non-multiplexed: resource type for algoSet2 DSP mode and non-multiplexed aal2 AAL mode.aal2 AAL mode. algoSet2-aal2-std: resource type for algoSet2 DSP mode and standard aal2 AAL mode. algoSet3-aal2-non-multiplexed: resource type for algoSet3 DSP mode and non-multiplexed aal2 AAL mode. algoSet3-aal2-std: resource type for algoSet3 DSP mode and standard aal2 AAL mode. algoSet5-aal1: resource type for algoSet5 DSP mode and aal1 AAL mode. algoSet6-aal2-std: resource type for algoSet6 DSP mode and standard aal2 AAL mode. tone-annce-cas: resource type for the tone announcement interface and CAS mode of the TASM card. tone-annce-tas: resource type for the tone announcement interface and TAS mode of the TASM card.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	algoSet1-aal2-non-multiplexed(1), algoSet1-aal2-std(2), algoSet2-aal2-non-multiplexed(3), algoSet2-aal2-std(4), algoSet3-aal2-non-multiplexed(5), algoSet3-aal2-std(6), algoSet5-aal1(7), algoSet6-aal2-std(8), tone-annce-cas(9), tone-annce-tas(10)

dspResourceAvail		3.1.1751.2.18.1.94.1.2
The available DSP resource counts how many connections can be made using this available DSP resource type in the system.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dspResourceUsed		3.1.1751.2.18.1.94.1.3
The used DSP resource counts how many connections are already made using this available DSP resource type in the system.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dspResourceUsedFailed		3.1.1751.2.18.1.94.1.4
The used but failed DSP resource counts how many connections are already made using currently failed DSP resource type in the system.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dspResourceAvailFailed		3.1.1751.2.18.1.94.1.5
The available but failed DSP resource counts how many connections can be made if using currently failed DSP resource type in the system.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

tasmMaxDigitControlBlocks		3.1.1751.2.18.1.95
Specifies the maximum number of digit collection that can be initiated simultaneously. This will depend on the number of control blocks allocated for playing tones and announcements and for line tests as the memory comes from the same pool. The tasmControlBlockResAllocUsage field will be updated to indicate this .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10000

tasmMaxTestControlBlocks		3.1.1751.2.18.1.96
Specifies the maximum number of TDM line tests that can be initiated simultaneously. This will depend on the number of control blocks allocated for playing tones and announcements and for digit collection as the memory comes from the same pool. The tasmControlBlockResAllocUsage field will be updated to indicate this.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10000

tasmMaxMemResvd		3.1.1751.2.18.1.97
Specifies the maximum amount of memory in megabytes reserved for TASM.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

tasmControlBlockResAllocUsage		3.1.1751.2.18.1.98
The percentage of memory usage for tones, announcements, digit collection and line tests control blocks.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

tasmAnnceCacheMemResAllocUsage		3.1.1751.2.18.1.99
The percentage of memory usage for caching announcements in memory. Everytime an announcement is compressed this field will be updated to reflect the cache memory that will be taken up by this announcement. Once this field shows a 100 percent usage it is an indication to the user that any additional announcement will cause the system to thrash as it clears an announcement in cache to make room for the new announcement.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

siteAlternateGatewayAddr		3.1.1751.2.18.1.100
Alternate ip address of gateway to access the site (switch),Can be used only over the InBand PVC connection when the OAM is enabled on InBand PVCs
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ipThrottlingConfig		3.1.1751.2.18.1.101
OBJECT IDENTIFIER

ipThrottlingFeatureStatus		3.1.1751.2.18.1.101.1
CPU card IP throttling feature: off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

ipThrottlingAllowedInFrameRate		3.1.1751.2.18.1.101.2
CPU card IP throttling: allowed input frames per second
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..20000

ipThrottlingLeakyBucketSize		3.1.1751.2.18.1.101.3
CPU card IP throttling: the size of leaky bucket
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..20000

ipThrottlingStatsOdometerTimer		3.1.1751.2.18.1.101.4
CPU card IP throttling: Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipThrottlingStatsOdometerReset		3.1.1751.2.18.1.101.5
CPU card IP throttling: Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

ipThrottlingInPackets		3.1.1751.2.18.1.101.6
CPU card IP throttling: the total number of input packets from both Ethernet port and In-band-mgmt of the CPU card.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipThrottlingInPacketsPassedEi		3.1.1751.2.18.1.101.7
CPU card IP throttling: the number of input packets passed through the Ethernet port of the CPU card.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipThrottlingInPacketsDroppedEi		3.1.1751.2.18.1.101.8
CPU card IP throttling: the number of input packets dropped from the Ethernet port of the CPU card.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipThrottlingInPacketsPassedIBM		3.1.1751.2.18.1.101.9
CPU card IP throttling: the number of input packets passed from the In-Band-Management of the CPU card.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipThrottlingInPacketsDroppedIBM		3.1.1751.2.18.1.101.10
CPU card IP throttling: the number of input packets dropped from the In-Band-Management of the CPU card.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

csSapphireInterfaceAddress		3.1.1751.2.18.1.102
The IP address to be specified as the source address in the TCP connect message that is sent to the SoftSwitch running as server and PSAX running as client.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

trapActivationTable		3.1.1751.2.18.1.103
Table of traps be turned on/off
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TrapActivationEntry

trapActivationEntry		3.1.1751.2.18.1.103.1
Row definition for trapActivation table
Status: current	Access: not-accessible
OBJECT-TYPE
	TrapActivationEntry

trapGroupId		3.1.1751.2.18.1.103.1.1
trap group ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	systemEvents(1), moduleEvents(2), interfaceEvents(3), connectionEvents(4)

trapIndex		3.1.1751.2.18.1.103.1.2
trap index in each group.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

trapActivationStatus		3.1.1751.2.18.1.103.1.3
activated: trap message activated. deactivated: trap message deactivated. permanently-activated: trap message can not be deactivated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), permanently-activated(3)

trapNames		3.1.1751.2.18.1.103.1.4
Name of the trap
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(50)

resetAction		3.1.1751.2.18.1.103.1.5
set-all-active: set all trap active one group. set-all-deactive: set all trap deactive in a group.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	set-all-active(1), set-all-deactive(2)

spvcGlobalPriorityScheme		3.1.1751.2.18.1.104
Flag indicating whether priority scheme should be supported across SPVCs and SPVC-trunks.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

spvcPriorityScheme		3.1.1751.2.18.1.105
Flag indicating whether priority scheme should be supported in SPVCs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

spvcTrunkingPriorityScheme		3.1.1751.2.18.1.106
Flag indicating whether priority scheme should be supported in SPVC-trunks.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmTrunkVccs		3.1.1751.2.18.1.107
The total number of ATM Trunk VCCs (including SigVccs and Bearer Vccs).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmTrunkNarrowBandCalls		3.1.1751.2.18.1.108
The total number of ATM Trunking Narrow Band Calls supported
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

dspResourceFeatureConfig		3.1.1751.2.18.1.109
OBJECT IDENTIFIER

dspReroutingFeature		3.1.1751.2.18.1.109.1
Dsp2 Rerouting Feature.This is used to enable or disable rerouting of connections when a dsp chip or card fails.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), auto-rerouting-enabled(2)

cardTable		3.1.1751.2.18.2.1
Table of card configuration data
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CardEntry

cardEntry		3.1.1751.2.18.2.1.1
Row definition for ac120 card
Status: current	Access: not-accessible
OBJECT-TYPE
	CardEntry

cardSlot		3.1.1751.2.18.2.1.1.1
Physical slot location. Valid range is a number between 1 and 24.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..24

cardType		3.1.1751.2.18.2.1.1.2
Type of card in a physical slot. A specific type of card is associated with each number. none(1) no board present taxi(2) Taxi oC-3c(3) OC3 dS3-ATM(4) DS3 ATM dS1-CE(5) DS1 circuit emulation dS1-ATM(6) DS1 ATM e1-CE(7) E1 circuit emulation e3-ATM(8) E3 ATM highSpeed(9) High Speed Serial mSerial(10) Multi Serial dSP1(11) DSP tWStation(12) Two Wire Station tWOffice(13) Two Wire Office cPU(14) Central Processor Unit stratum(15) Stratum pwrSupply(16) Power Supply protectionCard(17) protection card e1-ATM(18) E1 ATM ethernet(19) Ethernet enhDS1(20) Enhanced DS1 enhE1(21) Enhanced E1 oC-3cMMAQ(22) OC3 Multimode Aqueman oC-3cMMTS(23) OC3 Multimode Traffic Shaping oC-3cSMAQ(24) OC3 Singlemode Aqueman oC-3cSMTS(25) OC3 Singlemode Traffic Shaping sTM-1SMAQ(26) STM1 Singlemode Aqueman sTM-1SMTS(27) STM1 Singlemode Traffic Shaping sTM-1MMAQ(28) STM1 Multimode Aqueman sTM-1MMTS(29) STM1 Multimode Traffic Shaping dS3-FR(30) DS3 Frame Relay dSP2A(31) DSP2 card revision 2A dS1-IMA(32) DS1 Inverse Multiplexing over ATM (IMA) I/O card e1-IMA(33) E1 IMA alarm(34) alarm card dSP2B(35) DSP card revision 2B aps-OC-3cSM(36) Automatic Protection Switching OC3 Single Mode aps-OC-3cMM(37) Automatic Protection Switching OC3 Multi Mode msp-STM-1SM(38) Multi Switch Protection STM1 Singemode msp-STM-1MM(39) Multi Switch Protection STM1 Multimode cH-DS3(40) Channelized DS3 cH-STS1(41) Channelized STS1 rT-S(42) Route Server cC-Server(43) Continuity Check Server hD-E1(44) High Density E1 hD-DS1(45) High Density DS1 dS3-IMA(46) DS3 IMA dSP2C(47) DSP card revision 2C tasm(48) Tone Announcement Service Module mD-DS1(49) Medium Density DS1 quadSerial(50) Quad Serial mD-DS1-IMA(51) Medium Density DS1 IMA mD-E1-IMA(52) Medium Density E1 IMA hD-DS1-IMA(53) High Density DS1 IMA hD-E1-IMA(54) High Density E1 IMA chDS3STS1-3P(55) 3-port channelized DS3 STS1 unstDS3E3-3P(56) 3-port unstructured DS3 E3 dS3E3-ATM-3P(57) 3-port DS3 E3 ATM oC12c-STM4-MM(58) OC12 STM4 Multimode oC12c-STM4-SM(59) OC12 STM4 Singlemode dSP2D(60) DSP card revision 2D ethernet-4P(61) 4-port Ethernet chDS3STS1-3P-Prot(62) 3-port channelized DS3 STS1 protection alarm-fan(63) alarm fan card dS1-Nx64CAS(64) DS1 card supporting N x 64 CAS
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), taxi(2), oC-3c(3), dS3-ATM(4), dS1-CE(5), dS1-ATM(6), e1-CE(7), e3-ATM(8), highSpeed(9), mSerial(10), dSP1(11), tWStation(12), tWOffice(13), cPU(14), stratum(15), pwrSupply(16), protectionCard(17), e1-ATM(18), ethernet(19), enhDS1(20), enhE1(21), oC-3cMMAQ(22), oC-3cMMTS(23), oC-3cSMAQ(24), oC-3cSMTS(25), sTM-1SMAQ(26), sTM-1SMTS(27), sTM-1MMAQ(28), sTM-1MMTS(29), dS3-FR(30), dSP2A(31), dS1-IMA(32), e1-IMA(33), alarm(34), dSP2B(35), aps-OC-3cSM(36), aps-OC-3cMM(37), msp-STM-1SM(38), msp-STM-1MM(39), cH-DS3(40), cH-STS1(41), rT-S(42), cC-Server(43), hD-E1(44), hD-DS1(45), dS3-IMA(46), dSP2C(47), tasm(48), mD-DS1(49), quadSerial(50), mD-DS1-IMA(51), mD-E1-IMA(52), hD-DS1-IMA(53), hD-E1-IMA(54), chDS3STS1-3P(55), unstDS3E3-3P(56), dS3E3-ATM-3P(57), oC12c-STM4-MM(58), oC12c-STM4-SM(59), dSP2D(60), ethernet-4P(61), chDS3STS1-3P-Prot(62), alarm-fan(63), dS1-Nx64CAS(64)

cardProtectionStatus		3.1.1751.2.18.2.1.1.3
Current protection status of the card: none if the card is un-protected; protected if it is under the protection of another card; wrongType if the card types of protection card and protected card are different.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), protected(2), wrongType(3)

cardOperStatus		3.1.1751.2.18.2.1.1.4
Current operational status of the card. For I/O card, it is primary if configured, it is unknown if unconfigured, or removed. For CPU, it is primary if the CPU is master CPU, or standby if the CPU is slave CPU.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), standby(2), unknown(3)

cardAdminStatus		3.1.1751.2.18.2.1.1.5
administrative status
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	switchProtection(1)

cardAlarmStatus		3.1.1751.2.18.2.1.1.6
last alarm occurred
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), wrongCardType(2), lineFailed(3), cardRemoved(4), referenceClockFailed(5), compositeClockFailed(6), overload(7), plus5vFailed(8), plus120vFailed(9), minus48vFailed(10), unknownAlarm(11), completeClockFailed(12), backplaneCircuitryFailed(13), powerFailed(14), inputPortClkFailed(15)

cardCleiCode		3.1.1751.2.18.2.1.1.7
CLEI code
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(10)

cardRevision		3.1.1751.2.18.2.1.1.8
Card Revision number
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cardSerialNumber		3.1.1751.2.18.2.1.1.9
Serial Number
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(12)

cardOperatingMode		3.1.1751.2.18.2.1.1.10
Mode of operation for a card. This is applicable to those card types which can be configured in a dual mode. e.g. unstDS3E3-3P can be operational as either a 3 port DS3 or E3 card. All ports on the card will be of the same type depending on the card's operating mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), dS3(2), e3(3), sTS1e(4), oC12(5), sTM4(6)

protectionConfigMode		3.1.1751.2.18.2.1.1.11
Protection Configuration Mode of a Card unprotected: Card is not in protection or protected state protection: Card is in protection state working: Card is in protected/working state and this state is read only and cannot be set by the user
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unprotected(1), protection(2), working(3)

protectionStatus		3.1.1751.2.18.2.1.1.12
Protection Status of a card. Inservice and OutofService indicates if the card has failed or still operational. Active or Standby state indicates if it is carrying active traffic or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inservice-Active(2), inservice-Standby(3), outOfService-Active(4), outOfService-Standby(5)

protectionSlot		3.1.1751.2.18.2.1.1.13
If Protection Config Mode is Working then this field gives the protection slot.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..15

taxiPortConfigTable		3.1.1751.2.18.2.2
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TaxiPortConfigEntry

taxiPortConfigEntry		3.1.1751.2.18.2.2.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	TaxiPortConfigEntry

taxiPortId		3.1.1751.2.18.2.2.1.1
interface index - SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

taxiPortType		3.1.1751.2.18.2.2.1.2
taxi type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	taxi100(1), taxi140(2)

taxiLineStatus		3.1.1751.2.18.2.2.1.3
taxi line status: 1: NoAlarm 2: Loss of Signal
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2

taxiOutputTransferRate		3.1.1751.2.18.2.2.1.4
User selectable parameter which allows the outgoing rate of the port to be reduced to 50% taxi, halfRate, only on AQueMan.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	fullRate(1), halfRate(2)

ds3PortConfigTable		3.1.1751.2.18.2.3
Table of ds3 specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ds3PortConfigEntry

ds3PortConfigEntry		3.1.1751.2.18.2.3.1
Row definition for ds3 specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	Ds3PortConfigEntry

ds3PortId		3.1.1751.2.18.2.3.1.1
slot/port: SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ds3LineType		3.1.1751.2.18.2.3.1.2
This variable indicates the variety of DS3 C-bit implementing this interface. The type of interface affects the interpretation of the usage and error statistics. The rate of DS3 is 44.736 Mbps. The dsx3ClearChannel value means that the C-bits are not used except for sending/receiving AIS. The values, in sequence, describe: TITLE: SPECIFICATION: dsx3CbitParity ANSI T1.107a-1989 dsx3ClearChannel ANSI T1.102-1987.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cbitParity(1), clearChannel(2), m13(3), m23(4)

ds3LineCoding		3.1.1751.2.18.2.3.1.3
This variable describes the variety of Zero Code Suppression used on this interface, which in turn affects a number of its characteristics. ds3B3ZS refers to the use of specified patterns of normal bits and bipolar violations which are used to replace sequences of zero bits of a specified length.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	b3zs(1)

ds3LoopbackConfig		3.1.1751.2.18.2.3.1.4
This variable represents the loopback configuration of the DS3 interface. See above diagrams for explanations of loops.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noLoop(1), localLoop(2), lineLoop(3), payloadLoop(4)

ds3TransmitClockSource		3.1.1751.2.18.2.3.1.5
The source of Tranmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used. 'cardFreeRun' indicates that a local oscillator on the I/O card is used as the transmit clock. 'adaptiveTiming' indicates that the adaptive clocking mechanism is used
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTiming(1), localTiming(2), cardFreeRun(3), adaptiveTiming(4)

ds3LineStatus		3.1.1751.2.18.2.3.1.6
ds3 line status: 1: dsx3NoAlarm: No alarm present 2: dsx3RcvRAIFailure: Receiving Yellow/Remote Alarm Indication 4: dsx3XmitRAIAlarm: Transmitting Yellow/Remote Alarm Indication 8: dsx3RcvAIS: Receiving AIS failure state 16: dsx3XmitAIS: Transmitting AIS failure statue 32: dsx3LOF: Receiving LOF failure state 64: dsx3LOS: Reveiving LOS failure state 128: dsx3LoopbackState: Looping the received signal 256: dsx3RcvTestCode: Receiving a Test Pattern 512: dsx3OtherFailure: any line status not defined 1024: dsx3RcvRmtAIS: 2048: dsx3RcvRmtOOF: 4096: dsx3RcvRmtLOS: 8192: dsx3RcvRmtIdle: 16384: dsx3RmtLoopback: Far end remote loopback
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..32767

ds3LineBuildOut		3.1.1751.2.18.2.3.1.7
ds3 line build out
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	short(1), long(2)

ds3LineScramble		3.1.1751.2.18.2.3.1.8
ds3 line scramble
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

ds3CellMapping		3.1.1751.2.18.2.3.1.9
ds3 cell mapping method
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	plcp(1), directMapping(2)

ds3SendCode		3.1.1751.2.18.2.3.1.10
This variable indicates what type of code is being sent across the ds3 interface by the device. The values mean: 'noCode' - sending looped or normal data 'lineLoopCode' - sending a request for a line loopback 'deactivateCode' - sending a loopback deactivation request 'testPattern' - sending a test pattern
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noCode(1), lineLoopCode(2), deactivateCode(3), testPattern(4)

ds3OutputTxRate		3.1.1751.2.18.2.3.1.11
The ability to adjust the bandwidth of DS3 in tx direction. The adjustable DS3 bandwidth will support 1% increments.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

msPortConfigTable		3.1.1751.2.18.2.4
Table of multi-serial card's port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MsPortConfigEntry

msPortConfigEntry		3.1.1751.2.18.2.4.1
Row definition for multi-serial port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	MsPortConfigEntry

msPortId		3.1.1751.2.18.2.4.1.1
slot/port: SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

msLineCoding		3.1.1751.2.18.2.4.1.2
Line Coding.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nrz(1)

msBaudRate		3.1.1751.2.18.2.4.1.3
baud rate is determined by multiplying this number by the msBaudRateMultiplier
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	baud300(1), baud600(2), baud900(3), baud1200(4), baud1800(5), baud2400(6), baud3600(7), baud4800(8), baud7200(9), baud9600(10), baud14400(11), baud19200(12), baud28800(13), baud38400(14), baud57600(15), baud76800(16), baud115200(17), baud16k(18), baud32k(19), baud56k(20), baud64k(21), baud112k(22), baud128k(23), baud168k(24), baud192k(25), baud224k(26), baud256k(27), baud280k(28), baud320k(29), baud336k(30), baud384k(31), baud392k(32), baud448k(33), baud504k(34), baud512k(35), baud560k(36), baud576k(37), baud616k(38), baud640k(39), baud672k(40), baud704k(41), baud728k(42), baud768k(43), baud784k(44), baud832k(45), baud840k(46), baud896k(47), baud952k(48), baud960k(49), baud1008k(50), baud1024k(51), baud1064k(52), baud1088k(53), baud1120k(54), baud1152k(55), baud1176k(56), baud1216k(57), baud1232k(58), baud1280k(59), baud1288k(60), baud1344k(61), baud1400k(62), baud1408k(63), baud1456k(64), baud1472k(65), baud1512k(66), baud1536k(67), baud1568k(68), baud1600k(69), baud1624k(70), baud1664k(71), baud1680k(72), baud1728k(73), baud1736k(74), baud1792k(75), baud1856k(76), baud1920k(77), baud1984k(78), baud2048k(79), baud75(80), baud1848k(81), baud1904k(82), baud1960k(83), baud2016k(84), baud2072k(85), baud2112k(86), baud2128k(87), baud2176k(88), baud2184k(89), baud2240k(90), baud2296k(91), baud2304k(92), baud2352k(93), baud2368k(94), baud2408k(95), baud2432k(96), baud2464k(97), baud2496k(98), baud2520k(99), baud2560k(100), baud2576k(101), baud2624k(102), baud2632k(103), baud2688k(104), baud2744k(105), baud2752k(106), baud2800k(107), baud2816k(108), baud2856k(109), baud2880k(110), baud2912k(111), baud2944k(112), baud2968k(113), baud3008k(114), baud3024k(115), baud3072k(116), baud3080k(117), baud3136k(118), baud3192k(119), baud3200k(120), baud3248k(121), baud3264k(122), baud3304k(123), baud3328k(124), baud3360k(125), baud3392k(126), baud3416k(127), baud3456k(128), baud3472k(129), baud3520k(130), baud3528k(131), baud3584k(132), baud3640k(133), baud3648k(134), baud3696k(135), baud3712k(136), baud3752k(137), baud3776k(138), baud3808k(139), baud3840k(140), baud3864k(141), baud3904k(142), baud3920k(143), baud3968k(144), baud3976k(145), baud4032k(146), baud4088k(147), baud4096k(148), baud4144k(149), baud4160k(150), baud4200k(151), baud4224k(152), baud4256k(153), baud4288k(154), baud4312k(155), baud4352k(156), baud4368k(157), baud4416k(158), baud4424k(159), baud4480k(160), baud4536k(161), baud4544k(162), baud4592k(163), baud4608k(164), baud4648k(165), baud4672k(166), baud4704k(167), baud4736k(168), baud4760k(169), baud4800k(170), baud4816k(171), baud4864k(172), baud4872k(173), baud4928k(174), baud4984k(175), baud4992k(176), baud5040k(177), baud5056k(178), baud5096k(179), baud5120k(180), baud5152k(181), baud5184k(182), baud5208k(183), baud5248k(184), baud5264k(185), baud5312k(186), baud5320k(187), baud5376k(188), baud5432k(189), baud5440k(190), baud5488k(191), baud5504k(192), baud5544k(193), baud5568k(194), baud5600k(195), baud5632k(196), baud5656k(197), baud5696k(198), baud5712k(199), baud5760k(200), baud5768k(201), baud5824k(202), baud5880k(203), baud5888k(204), baud5936k(205), baud5952k(206), baud5992k(207), baud6016k(208), baud6048k(209), baud6080k(210), baud6104k(211), baud6144k(212), baud6160k(213), baud6208k(214), baud6216k(215), baud6272k(216), baud6328k(217), baud6336k(218), baud6384k(219), baud6400k(220), baud6440k(221), baud6464k(222), baud6496k(223), baud6528k(224), baud6552k(225), baud6592k(226), baud6608k(227), baud6656k(228), baud6664k(229), baud6720k(230), baud6776k(231), baud6784k(232), baud6832k(233), baud6848k(234), baud6888k(235), baud6912k(236), baud6944k(237), baud6976k(238), baud7000k(239), baud7040k(240), baud7056k(241), baud7104k(242), baud7112k(243), baud7168k(244), baud7224k(245), baud7232k(246), baud7280k(247), baud7296k(248), baud7336k(249), baud7360k(250), baud7392k(251), baud7424k(252), baud7448k(253), baud7488k(254), baud7504k(255), baud7552k(256), baud7560k(257), baud7616k(258), baud7680k(259), baud7672k(260), baud7728k(261), baud7744k(262), baud7784k(263), baud7808k(264), baud7840k(265), baud7872k(266), baud7896k(267), baud7936k(268), baud7952k(269), baud8000k(270), baud8008k(271), baud8064k(272), baud8120k(273), baud8128k(274), baud8176k(275), baud8192k(276), baud8232k(277), baud8256k(278), baud8288k(279), baud8320k(280), baud8344k(281), baud8384k(282), baud8400k(283), baud8448k(284), baud8456k(285), baud8512k(286), baud8568k(287), baud8576k(288), baud8624k(289), baud8640k(290), baud8680k(291), baud8704k(292), baud8736k(293), baud8768k(294), baud8792k(295), baud8832k(296), baud8848k(297), baud8896k(298), baud8904k(299), baud8960k(300), baud9016k(301), baud9024k(302), baud9072k(303), baud9088k(304), baud9128k(305), baud9152k(306), baud9184k(307), baud9216k(308), baud9240k(309), baud9280k(310), baud9296k(311), baud9344k(312), baud9352k(313), baud9408k(314), baud9464k(315), baud9472k(316), baud9520k(317), baud9536k(318), baud9576k(319), baud9600k(320), baud9632k(321), baud9664k(322), baud9688k(323), baud9728k(324), baud9744k(325), baud9792k(326), baud9800k(327), baud9856k(328), baud9912k(329), baud9920k(330), baud9968k(331), baud9984k(332), baud10024k(333), baud10048k(334), baud10080k(335), baud10112k(336), baud10136k(337), baud10176k(338), baud10192k(339), baud10240k(340), baud10248k(341), baud10304k(342), baud10360k(343), baud10368k(344), baud10416k(345), baud10432k(346), baud10472k(347), baud10496k(348), baud10528k(349), baud10560k(350), baud10584k(351), baud10624k(352), baud10640k(353), baud10688k(354), baud10696k(355), baud10752k(356), baud10808k(357), baud10816k(358), baud10864k(359), baud10880k(360), baud10920k(361), baud10944k(362), baud10976k(363), baud11008k(364), baud11032k(365), baud11072k(366), baud11088k(367), baud11136k(368), baud11144k(369), baud11200k(370), baud11256k(371), baud11264k(372), baud11312k(373), baud11328k(374), baud11368k(375), baud11392k(376), baud11424k(377), baud11456k(378), baud11480k(379), baud11520k(380), baud11536k(381), baud11584k(382), baud11592k(383), baud11648k(384), baud11704k(385), baud11712k(386), baud11760k(387), baud11776k(388), baud11816k(389), baud11840k(390), baud11872k(391), baud11904k(392), baud11928k(393), baud11968k(394), baud11984k(395), baud12032k(396), baud12040k(397), baud12096k(398), baud12152k(399), baud12160k(400), baud12208k(401), baud12224k(402), baud12264k(403), baud12288k(404), baud12320k(405), baud12352k(406), baud12376k(407), baud12416k(408), baud12432k(409), baud12480k(410), baud12488k(411), baud12544k(412), baud12600k(413), baud12608k(414), baud12656k(415), baud12672k(416), baud12712k(417), baud12736k(418), baud12768k(419), baud12800k(420), baud12824k(421), baud12864k(422), baud12880k(423), baud12928k(424), baud12936k(425), baud12992k(426), baud13048k(427), baud13056k(428), baud13104k(429), baud13120k(430), baud13160k(431), baud13184k(432), baud13216k(433), baud13248k(434), baud13272k(435), baud13312k(436), baud13328k(437), baud13376k(438), baud13384k(439), baud13440k(440), baud13496k(441), baud13504k(442), baud13552k(443), baud13568k(444), baud13608k(445), baud13632k(446), baud13664k(447), baud13696k(448), baud13720k(449), baud13760k(450), baud13776k(451), baud13824k(452), baud13832k(453), baud13888k(454), baud13944k(455), baud13952k(456), baud14000k(457), baud14016k(458), baud14056k(459), baud14080k(460), baud14112k(461), baud14144k(462), baud14168k(463), baud14208k(464), baud14224k(465), baud14272k(466), baud14280k(467), baud14336k(468), baud14400k(469), baud14464k(470), baud14528k(471), baud14592k(472), baud14656k(473), baud14720k(474), baud14784k(475), baud14848k(476), baud14912k(477), baud14976k(478), baud15040k(479), baud15104k(480), baud15168k(481), baud15232k(482), baud15296k(483), baud15360k(484), baud15424k(485), baud15488k(486), baud15552k(487), baud15616k(488), baud15680k(489), baud15744k(490), baud15808k(491), baud15872k(492), baud15936k(493), baud16000k(494), baud16064k(495), baud16128k(496), baud16192k(497), baud16256k(498), baud16320k(499), baud16384k(500), baud1544k(501), baud230400(502), baud150(503)

msProtocol		3.1.1751.2.18.2.4.1.4
protocol type for serial port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	rs232(1), rs449(2), rs530(3), v35(4), x21(5), kg(6), rs530A(7)

msEquipmentType		3.1.1751.2.18.2.4.1.5
Equipment type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dte(1), dce(2)

msRs232XmitMode		3.1.1751.2.18.2.4.1.6
transmit mode for rs232 DTE/DCE serial port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	synchronous(1), asynchronous(2)

msRs232Parity		3.1.1751.2.18.2.4.1.7
parity for rs232 DTE/DCE serial port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), odd(2), even(3)

msRs232DataBits		3.1.1751.2.18.2.4.1.8
data bits for rs232 DTE/DCE serial port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eight(1), seven(2), six(3)

msRs232StopBits		3.1.1751.2.18.2.4.1.9
stop bits for rs232 DTE/DCE serial port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	one(1), two(2)

msTxDataClkSrcForDte		3.1.1751.2.18.2.4.1.10
Transmit data clock source for DTE, externalTx in is not valid for rs232. This field is ignored if the local side is DCE.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	localTiming(1), txRxTiming(2), txTiming(3)

msTxDataClkSrcForDce		3.1.1751.2.18.2.4.1.11
Transmit data clock source for DCE localTiming: a local clock source is used. (e.g., from backplane (stratum) loopTiming: from remote This field is ignored if the local side is DTE
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	localTiming(1), loopTiming(2)

msRxDataClkSrcForDce		3.1.1751.2.18.2.4.1.12
Receive data clock source for DCE localTiming: a local clock source is used. (e.g., from backplane (stratum) loopTiming: from remote This field is ignored if the local side is DTE
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	localTiming(1), externalTiming(2)

msRxClkPolarity		3.1.1751.2.18.2.4.1.13
Whether or not to reverse the receive clock
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	standard(1), inverted(2)

msTxClkPolarity		3.1.1751.2.18.2.4.1.14
Whether or not to reverse the transmit clock
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	standard(1), inverted(2)

msKgResync		3.1.1751.2.18.2.4.1.15
Turn KG resync on/off
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

msHandshake		3.1.1751.2.18.2.4.1.16
Multiserial Module handshake: observed : used with AAL1 to monitor RTS/CTS exchange.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	observed(1), ignored(2)

msSpeedAdaption		3.1.1751.2.18.2.4.1.17
The state of allowing speed adaption
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

msBitStuffing		3.1.1751.2.18.2.4.1.18
When msBitStuffing is enabled, CAC throughput is (1 + 1/7) user throughtput. Otherwise the CAC throughput is the same as the user throughput. msBitStuffing can only be enabled for circuit emulation interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

msLineStatus		3.1.1751.2.18.2.4.1.19
line status on the port: The msLineStatus is a bit map representation. It can represent multiple failures (alarms) if supported by the card. NoAlarm should be set if and only if no other flag is set. The various bit positions are: 1: NoAlarm 2: Loss of Signal
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2

msRxDataPolarity		3.1.1751.2.18.2.4.1.20
Whether or not to reverse the receive data
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	standard(1), inverted(2)

msTxDataPolarity		3.1.1751.2.18.2.4.1.21
Whether or not to reverse the transmit data
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	standard(1), inverted(2)

msLoopbackConfig		3.1.1751.2.18.2.4.1.22
This variable represents the loopback configuration of the Serial port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noLoop(1), localLoop(2), lineLoop(3)

msLOSDetection		3.1.1751.2.18.2.4.1.23
State of detection of LOS by IO card. LOS detection is always enabled when msBitStuffing is enabled. When the interface is not circuit emulation, the IO card does not report any LOS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ds1PortConfigTable		3.1.1751.2.18.2.5
Table of ds1 specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ds1PortConfigEntry

ds1PortConfigEntry		3.1.1751.2.18.2.5.1
Row definition for ds1 specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	Ds1PortConfigEntry

ds1PortId		3.1.1751.2.18.2.5.1.1
interface index - slot/port: SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ds1Channelization		3.1.1751.2.18.2.5.1.2
ds1 interface type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ds1LineType		3.1.1751.2.18.2.5.1.3
ds1 interface type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	esf(1), d4(2)

ds1LineCoding		3.1.1751.2.18.2.5.1.4
ds1 interface type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	b8zs(1), ami(2)

ds1LoopbackConfig		3.1.1751.2.18.2.5.1.5
This variable represents the loopback configuration of the ds1 interface
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noLoop(1), localLoop(2), lineLoop(3), payloadLoop(4)

ds1TransmitClockSource		3.1.1751.2.18.2.5.1.6
ds1 timing source
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTiming(1), localTiming(2), adaptive(3)

ds1LineBuildOut		3.1.1751.2.18.2.5.1.7
ds1 line build out
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	upTo133Feet(1), upTo266Feet(2), upTo399Feet(3), upTo533Feet(4), upTo655Feet(5), negative7-5Db(6), negative15Db(7), negative22-5Db(8)

ds1LineStatus		3.1.1751.2.18.2.5.1.8
This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'alarm' infor- mation. The dsx1LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. ds1NoAlarm should be set if and only if no other flag is set. If the ds1LoopbackState bit is set, the loopbak in effect can be determined from the ds1LoopbackConfig object. The various bit positions are: 1: dsx1NoAlarm: No Alarm Present 2: dsx1RcvFarEndLOF: Far end LOF (a.k.a., Yellow Alarm) 4: dsx1XmtFarEndLOF: Near end sending LOF Indication 8: dsx1RcvAIS: Far end sending AIS 16: dsx1XmtAIS: Near end sending AIS 32: dsx1LossOfFrame: Near end LOF (a.k.a., Red Alarm) 64: dsx1LossOfSignal: Near end Loss Of Signal 128: dsx1LoopbackState: Near end is looped 256: dsx1T16AIS: E1 TS16 AIS 512: dsx1RcvFarEndLOMF: Far End Sending TS16 LOMF 1024: dsx1XmtFarEndLOMF: Near End Sending TS16 LOMF 2048: dsx1RcvTestCode: Near End detects a test code 4096: dsx1OtherFailure: any line status not defined here 8192: dsx1RmtLoopback: Far end loopback
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..16383

ds1EnhanceFeatureSet1		3.1.1751.2.18.2.5.1.10
To enable/disable a proprietary ab signaling scheme, it applies to all DS0s in the port. No individual DS0 signaling can be configured under this scheme.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ds1DataTransferType		3.1.1751.2.18.2.5.1.11
DS1 data transfer type is only applicable in Circuit Emulation where unstructured CE packets entire T1 frame including the F-bit into the AAL1 for data tranfer, whereas, the structured CE packets the entire T1 frame except the F-bit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	structured(1), unstructured(2)

ds1OamInterworkingType		3.1.1751.2.18.2.5.1.12
Specifies whether the interworking is done by trunk conditioning or unframed1s
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	trunkCond(1), unframed1s(2)

ds1ConnGatewayFeature		3.1.1751.2.18.2.5.1.14
To enable/disable connection gateway (Sapphire) API.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ds1InLineCode		3.1.1751.2.18.2.5.1.15
To select and support the inlinecode option in either ANSI or DS1_ANI (ANI: Access Network Interface)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aNSI(1), ds1-ANI(2)

oc3PortConfigTable		3.1.1751.2.18.2.6
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Oc3PortConfigEntry

oc3PortConfigEntry		3.1.1751.2.18.2.6.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	Oc3PortConfigEntry

oc3PortId		3.1.1751.2.18.2.6.1.1
interface index - SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

oc3LoopbackConfig		3.1.1751.2.18.2.6.1.2
This variable represents the loopback configuration of the OC3 interface See above diagrams for explanations of loops.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noLoop(1), localLoop(2), lineLoop(3)

oc3TransmitClockSource		3.1.1751.2.18.2.6.1.3
The source of Tranmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTiming(1), localTiming(2)

oc3LineStatus		3.1.1751.2.18.2.6.1.4
oc3 line status - 1: oc3NoAlarm: No alarm present 2: oc3RcvRAIFailure: Receiving Yellow/Remote Alarm Indication 4: oc3XmitRAIAlarm: Transmitting Yellow/Remote Alarm Indication 8: oc3RcvAIS: Receiving AIS failure state 16: oc3XmitAIS: Transmitting AIS failure statue 32: oc3LOF: Receiving LOF failure state 64: oc3LOS: Reveiving LOS failure state 128: oc3LoopbackState: Looping the received signal 256: oc3RcvTestCode: Receiving a Test Pattern 512: oc3OtherFailure: any line status not defined 1024: oc3LCD: Receiving Loss Of Cell Delineation 2048: oc3LRDI: Receiving Line RDI failure state 4096: oc3PRDI: Receiving Path RDI failure state
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..8191

oc3OutputTransferRate		3.1.1751.2.18.2.6.1.5
User selectable parameter which allows the outgoing rate of the port to be reduced to 50% oc3, halfRate, only on AQueMan.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	fullRate(1), halfRate(2)

oc3APSConfiguration		3.1.1751.2.18.2.6.1.6
Indicates whether APS is configured for this port .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unprotected(1), working(2), protection(3)

oc3APS		3.1.1751.2.18.2.16
OBJECT IDENTIFIER

oc3APSPairConfigTable		3.1.1751.2.18.2.16.1
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Oc3APSPairConfigEntry

oc3APSPairConfigEntry		3.1.1751.2.18.2.16.1.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	Oc3APSPairConfigEntry

oc3APSPairId		3.1.1751.2.18.2.16.1.1.1
APS Pair Port index - SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

oc3APSPairMode		3.1.1751.2.18.2.16.1.1.2
Unidirectional or Bidirectional mode: Uni - Each pair operates independently i.e. a switch over in one pair does not effect the remote pair. Bi - both remote and local pairs have to switch together.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unidirectional(1), bidirectional(2)

oc3APSPairOption		3.1.1751.2.18.2.16.1.1.3
Nonrevertive - After a switch to Prot port, even if the working comes up there is no switch to the working port back. Revertive - traffic is switched back to work port after it comes back.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nonrevertive(1), revertive(2)

oc3APSPairWorkingSFBERThreshold		3.1.1751.2.18.2.16.1.1.4
Bits error Rate threshold to declare signal failure
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tenToMinus4(1), tenToMinus5(2)

oc3APSPairProtectionSFBERThreshold		3.1.1751.2.18.2.16.1.1.6
Bits error Rate threshold to declare signal failure
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tenToMinus4(1), tenToMinus5(2)

oc3APSPairWorkingSDBERThreshold		3.1.1751.2.18.2.16.1.1.5
Bits error Rate threshold to declare signal degrade
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tenToMinus5(1), tenToMinus6(2), tenToMinus7(3), tenToMinus8(4)

oc3APSPairProtectionSDBERThreshold		3.1.1751.2.18.2.16.1.1.7
Bits error Rate threshold to declare signal degrade
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tenToMinus5(1), tenToMinus6(2), tenToMinus7(3), tenToMinus8(4)

oc3APSPairWTRPeriod		3.1.1751.2.18.2.16.1.1.8
Duration for Wait To Restore Period between 5 to 12 minutes. Ref: BellCore GR-253-Core, Issue 3, page 200, R5-56.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..12

oc3APSWorkingSlot		3.1.1751.2.18.2.16.1.1.9
Working slot of APS pair.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3APSProtectionSlot		3.1.1751.2.18.2.16.1.1.10
Protection slot of APS pair.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3APSActiveSlot		3.1.1751.2.18.2.16.1.1.11
Active slot of APS pair.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3APSPairStatus		3.1.1751.2.18.2.16.1.1.12
noFailure : The protection line is not in use. modeMismatch : one end is configured unidirectional and the other is bidirectional (both the ends should be configured in the same mode). Also when one end is configured for 1:1 architechture and the other end indicates it is configured for 1:n architechture.(Bidirectional mode only) swByteFailure: protection switching byte failure - defect declared when invalid / persistantly unacceptable codes are received in the K1 byte. failure declared if defect persists for an extended period. Invalid code is when the incoming K1 byte contains an unused code or a code irrelevant for the specific switching operation.(Only in bi-directional mode) chMismatch : channel mismatch is declared when the channel numbers in the transmitted K1 byte and the received K2 byte do not match for 50 ms.Channel mismatch is monitored only in bidirectional mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noFailure(1), modeMismatch(2), swByteFailure(3), chMismatch(4)

oc3APSPairUserCommand		3.1.1751.2.18.2.16.1.1.13
APS Pair User Command
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noAction(1), manualSwitchToWorkingPort(2), manualSwitchToProtectionPort(3), forcedSwitchToWorkingPort(4), forcedSwitchToProtectionPort(5), lockoutProtection(6), clear(7)

oc3APSPairCurrentState		3.1.1751.2.18.2.16.1.1.14
Current State of the APS state machine
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	localprotectDoNotRevert(1), localprotectManualSw(8), localprotectSD(10), localprotectSF(12), localprotectForced(14), localprotectLockOut(15), localworkingDoNotRevert(17), localworkingManualSw(24), localworkingSD(26), localworkingSF(28), localworkingForced(30), remoteprotectDoNotRevert(33), remoteprotectManualSw(40), remoteprotectSD(42), remoteprotectSF(44), remoteprotectForced(46), remoteprotectLockOut(47), noRequest(48), remoteworkingDoNotRevert(49), remoteworkingManualSw(56), remoteworkingSD(58), remoteworkingSF(60), remoteworkingForced(62)

oc3APSPairWorkingLineSignalStatus		3.1.1751.2.18.2.16.1.1.15
Signal Status of the working port (LOS / LOF / LCD / AIS etc.)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), signalDegradation(2), signalFailure(4), lostCellDelineation(8), switchByteFailure(16), ais-l(32), ais-p(64), lop(128), lof(256), los(512), moduleFailure(1024), lineLoopBack(2048), protocolFailure(4096), adminOutOfService(8192)

oc3APSPairProtectionLineSignalStatus		3.1.1751.2.18.2.16.1.1.16
Signal Status of the protection port (LOS / LOF / LCD / AIS etc.)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), signalDegradation(2), signalFailure(4), lostCellDelineation(8), switchByteFailure(16), ais-l(32), ais-p(64), lop(128), lof(256), los(512), moduleFailure(1024), lineLoopBack(2048), protocolFailure(4096), adminOutOfService(8192)

oc3APSPairStatsTable		3.1.1751.2.18.10.8
Table of statisics for a OC3 port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Oc3APSPairStatsEntry

oc3APSPairStatsEntry		3.1.1751.2.18.10.8.1
Row definition for the OC3 port statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	Oc3APSPairStatsEntry

oc3APSPairStatsId		3.1.1751.2.18.10.8.1.1
Working Port ID - Slot/Port (SSPP)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

oc3APSPairWorkingSFDuration		3.1.1751.2.18.10.8.1.2
Duration in seconds for which the Work port has been in Signal Failure state
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3APSPairWorkingSDDuration		3.1.1751.2.18.10.8.1.3
Duration in seconds for which the Work port has been in Signal Degradation state
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3APSPairProtectionSFDuration		3.1.1751.2.18.10.8.1.4
Duration in seconds for which the Prot port has been in Signal Failure state
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3APSPairProtectionSDDuration		3.1.1751.2.18.10.8.1.5
Duration in seconds for which the Prot port has been in Signal Degradation state
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3APSPairTransmitK1K2Bytes		3.1.1751.2.18.10.8.1.6
The k1 / k2 bytes being transmitted by the prot port to the remote port.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

oc3APSPairReceiveK1K2Bytes		3.1.1751.2.18.10.8.1.7
k1 / k2 bytes from the received SONET header on the protection port. k1 / k2 are used for the APS communication protocol.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

oc3APSPairSwitchOverCount		3.1.1751.2.18.10.8.1.8
Number of times the APS pair has switched over since last configuration.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

twoWireSourcePortConfigTable		3.1.1751.2.18.2.7
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TwoWireSourcePortConfigEntry

twoWireSourcePortConfigEntry		3.1.1751.2.18.2.7.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	TwoWireSourcePortConfigEntry

twoWireSourcePortId		3.1.1751.2.18.2.7.1.1
interface index - SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

twoWireSourceLoopDetection		3.1.1751.2.18.2.7.1.2
This field selects terminal equipment loop circuit detection mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	loopStart(1), groundStart(2)

twoWireSourceDialMode		3.1.1751.2.18.2.7.1.3
This field configures twoWireSource card to support communication terminal equipment.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	dtmf(1), dialPulse(2)

twoWireSourceLoopBackConfig		3.1.1751.2.18.2.7.1.4
Configuration of 2W Source LoopBack.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noLoopback(1), facilityLoopback(2)

twoWireSourceLineStatus		3.1.1751.2.18.2.7.1.5
twoWireSource line status: 1: NoAlarm: No alarm present 2: SignalingFailureState 4: FacilityLoopBack 8: Maintenance 16: Out Of Service 32: OtherFailure
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1023

twoWireSourceSignalingBits		3.1.1751.2.18.2.7.1.6
This field selects the signaling bits as seen in DS1 signal, ab or abcd.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ab(1), abcd(2)

twoWireSourceRingCadence		3.1.1751.2.18.2.7.1.7
This field selects ring On/Off pattern.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	oneOnThreeOff(1)

twoWireSourceSignalingState		3.1.1751.2.18.2.7.1.8
This field reflects the current signaling state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), dtmf(2), ringBack(3), connect(4), onHook(5), ringTrip(6), nearEndDisconnect(7), farEndDisconnect(8)

twoWireSourceTestMode		3.1.1751.2.18.2.7.1.9
This field selects line test mode. For normal operation, this field should be OFF.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), quietTime(2), f-1004Hz(3)

highSpeedPortConfigTable		3.1.1751.2.18.2.8
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HighSpeedPortConfigEntry

highSpeedPortConfigEntry		3.1.1751.2.18.2.8.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	HighSpeedPortConfigEntry

highSpeedPortId		3.1.1751.2.18.2.8.1.1
interface index - SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

highSpeedPortInputRate		3.1.1751.2.18.2.8.1.2
Port input rate
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

highSpeedPortOutputRate		3.1.1751.2.18.2.8.1.3
Port output rate
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

dspPortConfigTable		3.1.1751.2.18.2.9
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DspPortConfigEntry

dspPortConfigEntry		3.1.1751.2.18.2.9.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	DspPortConfigEntry

dspPortId		3.1.1751.2.18.2.9.1.1
interface index - SSPP
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

twoWireSinkPortConfigTable		3.1.1751.2.18.2.10
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TwoWireSinkPortConfigEntry

twoWireSinkPortConfigEntry		3.1.1751.2.18.2.10.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	TwoWireSinkPortConfigEntry

twoWireSinkPortId		3.1.1751.2.18.2.10.1.1
interface index - SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

twoWireSinkLoopDetection		3.1.1751.2.18.2.10.1.2
Types of loop detection.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	loopStart(1), groundStart(2)

twoWireSinkDialMode		3.1.1751.2.18.2.10.1.3
This field selects subscribed dial mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	dtmf(1), dialPulse(2)

twoWireSinkLineStatus		3.1.1751.2.18.2.10.1.4
twoWireSink line status: 1: NoAlarm: No alarm present 2: SignalingFailureState 4: FacilityLoopBack 8: Maintenance 16: Out Of Service 32: OtherFailure
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1023

twoWireSinkSignalingBits		3.1.1751.2.18.2.10.1.5
This field selects the signaling bits as seen in DS1 signal, ab or abcd.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ab(1), abcd(2)

twoWireSinkSignalingState		3.1.1751.2.18.2.10.1.6
This field reflects the current signaling state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), connect(2), onHook(3), ringTrip(4), nearEndDisconnect(5), farEndDisconnect(6)

twoWireSinkTestMode		3.1.1751.2.18.2.10.1.7
This field selects line test mode. For normal operation, this field should be OFF.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), quietTime(2), f-1004Hz(3)

e3PortConfigTable		3.1.1751.2.18.2.11
Table of e3 specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		E3PortConfigEntry

e3PortConfigEntry		3.1.1751.2.18.2.11.1
Row definition for e3 specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	E3PortConfigEntry

e3PortId		3.1.1751.2.18.2.11.1.1
slot/port: SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

e3LineType		3.1.1751.2.18.2.11.1.2
This variable indicates the basic frame structure supported in this E3 port. The rate of E3 is 34.368 Mbps. TITLE: SPECIFICATION: G.832 ITU-T G.832 1993. G.751 ITU-T G.751 1998
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	g832(1), g751(2)

e3LineCoding		3.1.1751.2.18.2.11.1.3
The line code supported for the E3 port. The High Density Bipolar of order 3 (hdb3) as specified in section 8.1 of ITU-T G.703.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	hdb3(1)

e3LoopbackConfig		3.1.1751.2.18.2.11.1.4
This variable represents the loopback configuration of the E3 interface. See above diagrams for explanations of loops.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noLoop(1), localLoop(2), lineLoop(3), payloadLoop(4)

e3TransmitClockSource		3.1.1751.2.18.2.11.1.5
The source of Tranmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used. 'adaptiveTiming' indicates that the adaptive clocking mechanism is used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTiming(1), localTiming(2), adaptiveTiming(3)

e3LineStatus		3.1.1751.2.18.2.11.1.6
e3 line status: 1: e3NoAlarm: No alarm present 2: e3RcvRAIFailure: Receiving Yellow/Remote Alarm Indication 4: e3XmitRAIAlarm: Transmitting Yellow/Remote Alarm Indication 8: e3RcvAIS: Receiving AIS failure state 16: e3XmitAIS: Transmitting AIS failure statue 32: e3LOF: Receiving LOF failure state 64: e3LOS: Reveiving LOS failure state 128: e3LoopbackState: Looping the received signal 256: e3RcvTestCode: Receiving a Test Pattern 512: e3OtherFailure: any line status not defined
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1023

e3LineBuildOut		3.1.1751.2.18.2.11.1.7
e3 line build out
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	short(1), long(2)

e3LineScramble		3.1.1751.2.18.2.11.1.8
e3 line scramble
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

e3CellMapping		3.1.1751.2.18.2.11.1.9
e3 cell mapping method
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	directMapping(1), plcp(2)

e1PortConfigTable		3.1.1751.2.18.2.12
Table of e1 specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		E1PortConfigEntry

e1PortConfigEntry		3.1.1751.2.18.2.12.1
Row definition for e1 specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	E1PortConfigEntry

e1PortId		3.1.1751.2.18.2.12.1.1
interface index - slot/port: SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

e1Channelization		3.1.1751.2.18.2.12.1.2
e1 interface type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

e1LineType		3.1.1751.2.18.2.12.1.3
E1 interface type. The rate of E1 is 2.048 Mbps
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	crc-mf(1)

e1LineCoding		3.1.1751.2.18.2.12.1.4
e1 interface type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	hdb3(1)

e1LoopbackConfig		3.1.1751.2.18.2.12.1.5
This variable represents the loopback configuration of the e1 interface See above diagrams for explanations of loops.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noLoop(1), localLoop(2), lineLoop(3)

e1TransmitClockSource		3.1.1751.2.18.2.12.1.6
e1 timing source
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTiming(1), localTiming(2), adaptive(3)

e1LineNationalBits		3.1.1751.2.18.2.12.1.7
e1 line country specific code
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	b00000(1), b00001(2), b00010(3), b00011(4), b00100(5), b00101(6), b00110(7), b00111(8), b01000(9), b01001(10), b01010(11), b01011(12), b01100(13), b01101(14), b01110(15), b01111(16), b10000(17), b10001(18), b10010(19), b10011(20), b10100(21), b10101(22), b10110(23), b10111(24), b11000(25), b11001(26), b11010(27), b11011(28), b11100(29), b11101(30), b11110(31), b11111(32)

e1LineStatus		3.1.1751.2.18.2.12.1.8
This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'alarm' infor- mation. The e1LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. e1NoAlarm should be set if and only if no other flag is set. If the e1LoopbackState bit is set, the loopback in effect can be determined from the e1LoopbackConfig object. The various bit positions are: 1: e1NoAlarm: No Alarm Present 2: e1RcvFarEndLOF: Far end LOF (a.k.a., Yellow Alarm) 4: e1XmtFarEndLOF: Near end sending LOF Indication 8: e1RcvAIS: Far end sending AIS 16: e1XmtAIS: Near end sending AIS 32: e1LossOfFrame: Near end LOF (a.k.a., Red Alarm) 64: e1LossOfSignal: Near end Loss Of Signal 128: e1LoopbackState: Near end is looped 256: e1T16AIS: E1 TS16 AIS 512: e1RcvFarEndLOMF: Far End Sending TS16 LOMF 1024: e1XmtFarEndLOMF: Near End Sending TS16 LOMF 2048: e1RcvTestCode: Near End detects a test code 4096: e1OtherFailure: any line status not defined here
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..8191

e1TS16		3.1.1751.2.18.2.12.1.10
Time slot 16 is configurable for channel associated signaling (CAS) or data. cas: 'ABCD' signaling will be extracted in time slot 16 if channel is configured for circuit emulation. ccs: time slot 16 will not carry any e1 channel signaling information, instead, it will be used for data.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cas(1), ccs(2)

e1DataTransferType		3.1.1751.2.18.2.12.1.11
E1 data transfer type is only applicable in Circuit Emulation where unstructured CE packets entire T1 frame including the F-bit into the AAL1 for data tranfer, whereas, the structured CE packets the entire E1 frame except the Frame alignment signal channel.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	structured(1), unstructured(2)

e1CRC4		3.1.1751.2.18.2.12.1.12
Enable or disable transmission of CRC4 bits on bit 1 of each frame.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

e1OamInterworkingType		3.1.1751.2.18.2.12.1.13
Specifies whether the interworking is done by trunk conditioning or unframed1s
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	trunkCond(1), unframed1s(2)

e1EnhanceFeatureSet1		3.1.1751.2.18.2.12.1.14
To enable/disable a proprietary ab signaling scheme, it applies to all DS0s in the port. No individual DS0 signaling can be configured under the scheme.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

e1ConnGatewayFeature		3.1.1751.2.18.2.12.1.15
To enable/disable connection gateway (Sapphire) API.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ethernetPortConfigTable		3.1.1751.2.18.2.13
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthernetPortConfigEntry

ethernetPortConfigEntry		3.1.1751.2.18.2.13.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	EthernetPortConfigEntry

ethernetPortId		3.1.1751.2.18.2.13.1.1
interface index - SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ethernetLinkType		3.1.1751.2.18.2.13.1.2
The type of port can either be set to 10baseT or 100baseT for the first port on the ethernet card. The other ports can only be set to 10baseT. The Auto mode will detect what LAN speed the port is connected to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	l-10BaseT(1), l-100BaseT(2), auto(3)

ethernetPhysicalAddr		3.1.1751.2.18.2.13.1.3
The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1dSprPriority a unique Bridgeidentifier is formed which is used in the Spanning Tree Protocol.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(6)

ethernetLineStatus		3.1.1751.2.18.2.13.1.4
ethernet line status: 1: Down 2: 10baseT-FullDuplex 4: 10baseT-HalfDuplex 8: 100baseT-FullDuplex 16: 100baseT-HalfDuplex
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..31

ethernetDuplexMode		3.1.1751.2.18.2.13.1.5
Set the port to either be in full or half duplex. You can also set the port to auto detect the mode it is connected to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), half(2), auto(3)

dsp2PortConfigTable		3.1.1751.2.18.2.14
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsp2PortConfigEntry

dsp2PortConfigEntry		3.1.1751.2.18.2.14.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsp2PortConfigEntry

dsp2PortId		3.1.1751.2.18.2.14.1.1
interface index - SSPP
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

imaPortConfigTable		3.1.1751.2.18.2.15
Table used for the IMA virtual port on cards that have physical interfaces configured as atmIma. Corresponds to port 7 on DS1 and E1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ImaPortConfigEntry

imaPortConfigEntry		3.1.1751.2.18.2.15.1
Row definition for ima specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	ImaPortConfigEntry

imaPortId		3.1.1751.2.18.2.15.1.1
interface index - slot/port: SSPP
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sts1PortConfigTable		3.1.1751.2.18.2.17
Table of sts-1 specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sts1PortConfigEntry

sts1PortConfigEntry		3.1.1751.2.18.2.17.1
Row definition for sts-1 specific port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	Sts1PortConfigEntry

sts1PortId		3.1.1751.2.18.2.17.1.1
slot/port: SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

sts1LineCoding		3.1.1751.2.18.2.17.1.2
This variable describes the variety of Zero Code Suppression used on this interface, which in turn affects a number of its characteristics. B3ZS refers to the use of specified patterns of normal bits and bipolar violations which are used to replace sequences of zero bits of a specified length.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	b3zs(1)

sts1LoopbackConfig		3.1.1751.2.18.2.17.1.3
This variable represents the loopback configuration of the sts-1 interface. See above diagrams for explanations of loops.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noLoop(1), localLoop(2), lineLoop(3), payloadLoop(4)

sts1TransmitClockSource		3.1.1751.2.18.2.17.1.4
The source of Tranmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used. 'cardFreeRun' indicates that a local oscillator on the I/O card is used as the transmit clock.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTiming(1), localTiming(2), cardFreeRun(3)

sts1LineBuildOut		3.1.1751.2.18.2.17.1.5
sts-1 line build out
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	short(1), long(2)

sts1LineStatus		3.1.1751.2.18.2.17.1.6
sts-1 line status: 1: dsx3NoAlarm: No alarm present 2: dsx3RcvRAIFailure: Receiving Yellow/Remote Alarm Indication 4: dsx3XmitRAIAlarm: Transmitting Yellow/Remote Alarm Indication 8: dsx3RcvAIS: Receiving AIS failure state 16: dsx3XmitAIS: Transmitting AIS failure statue 32: dsx3LOF: Receiving LOF failure state 64: dsx3LOS: Reveiving LOS failure state 128: dsx3LoopbackState: Looping the received signal 256: dsx3RcvTestCode: Receiving a Test Pattern 512: dsx3OtherFailure: any line status not defined 1024: dsx3RcvRmtAIS: 2048: dsx3RcvRmtOOF: 4096: dsx3RcvRmtLOS: 8192: dsx3RcvRmtIdle: 16384: dsx3RmtLoopback: Far end remote loopback
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..32767

sts1StsPointers		3.1.1751.2.18.2.17.1.7
status of the sts-1 sts pointers
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	locked(1), floating(2)

sts1VtPointers		3.1.1751.2.18.2.17.1.8
status of the sts-1 vt pointers
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	locked(1), floating(2)

tasmPortConfigTable		3.1.1751.2.18.2.18
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TasmPortConfigEntry

tasmPortConfigEntry		3.1.1751.2.18.2.18.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	TasmPortConfigEntry

tasmPortId		3.1.1751.2.18.2.18.1.1
interface index - SSPP
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

protectionGroupConfigTable		3.1.1751.2.18.2.19
This table gives the list of Slot Protection Groups in the System. Slot protection group in one in which there are n cards being protected by 1 standby card.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ProtectionGroupConfigEntry

protectionGroupConfigEntry		3.1.1751.2.18.2.19.1
Row Definition for the Protection Group Tables
Status: current	Access: not-accessible
OBJECT-TYPE
	ProtectionGroupConfigEntry

protectionSlotId		3.1.1751.2.18.2.19.1.1
Protection Group Index. Index is the slot id of the Slot Configured as Protection.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..15

workingSlotBitmap		3.1.1751.2.18.2.19.1.2
Working Slot Bitmap which the protection slot will monitor
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

protectionCommand		3.1.1751.2.18.2.19.1.3
List of commands which can be executed on a protection Group. Clear : This command is used to clear any previous commands which may have been and get back to normal nto1 operation Forced SwitchOver To Protection : Switchover to Protection card even if the working card is in service active These commands to used in conjunction with the working slot id.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1), forcedSwitchOverToProtection(2)

protectionCommandSlotId		3.1.1751.2.18.2.19.1.4
This is the working Slot to which command has to be applied
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..15

protectionGroupStatus		3.1.1751.2.18.2.19.1.5
Protection Status of a Protection Card. Inservice and OutofService indicates if the card has failed or still operational. Active or Standby state indicates if it is carrying active traffic or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inservice-Active(2), inservice-Standby(3), outOfService-Active(4), outOfService-Standby(5)

workingSlotId		3.1.1751.2.18.2.19.1.6
If protection group status is active, this field will give the slot which is being working. In case it is in standby mode this field will show 0
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..15

workingFailedBitmap		3.1.1751.2.18.2.19.1.7
Gives Bitmap of the Failed Working Slots. Subset of the Working Slot Bitmap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

protectionActiveCounter		3.1.1751.2.18.2.19.1.8
Give the Number of Times a Protection has gone to active.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

protectionOOSCounter		3.1.1751.2.18.2.19.1.9
Give the Number of Times a Protection Card has failed.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

taxiChannelConfigTable		3.1.1751.2.18.3.1
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TaxiChannelConfigEntry

taxiChannelConfigEntry		3.1.1751.2.18.3.1.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	TaxiChannelConfigEntry

taxiChannelId		3.1.1751.2.18.3.1.1.1
interface index - SSPPCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

taxiChannelIfType		3.1.1751.2.18.3.1.1.2
UNI or NNI type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), atmUni3-0(2), atmUni3-1(3), iispUser(4), iispNetwork(5), atmUni4-0(6)

taxiChannelSecuFeature		3.1.1751.2.18.3.1.1.3
enhancement feature
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsecurable(1), secured(2), securable(3)

ds3ChannelConfigTable		3.1.1751.2.18.3.2
Table of common physical channel attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ds3ChannelConfigEntry

ds3ChannelConfigEntry		3.1.1751.2.18.3.2.1
Row definition for common physical channel attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	Ds3ChannelConfigEntry

ds3ChannelId		3.1.1751.2.18.3.2.1.1
interface index - SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

ds3ChannelIfType		3.1.1751.2.18.3.2.1.2
UNI or NNI type,
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), atmUni3-0(2), atmUni3-1(3), iispUser(4), iispNetwork(5), frameRelayUni(6), frameRelayNni(7), atmPnni1-0(8), atmUni4-0(9), circuitEmulation(10)

ds3ChannelSecuFeature		3.1.1751.2.18.3.2.1.3
Interface type configured on DS3 channel
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsecurable(1), secured(2), securable(3)

ds1ChannelConfigTable		3.1.1751.2.18.3.3
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ds1ChannelConfigEntry

ds1ChannelConfigEntry		3.1.1751.2.18.3.3.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	Ds1ChannelConfigEntry

ds1ChannelId		3.1.1751.2.18.3.3.1.1
interface index - SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

ds1ChannelIfType		3.1.1751.2.18.3.3.1.2
UNI or NNI type for ATM ,Frame Relay, or ISDN service interface type for channel
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), atmUni3-0(2), atmUni3-1(3), iispUser(4), iispNetwork(5), circuitEmulation(6), frameRelayUni(7), hdlcPassThrough(8), pri-isdn-network(9), dbCirEm(10), frameRelayNni(11), pri-isdn-user(12), atmIma(13), atmPnni1-0(14), casTrunkLine(15), atmUni4-0(16), gr303(17)

ds1ChannelDs0Map		3.1.1751.2.18.3.3.1.3
bit map of DS0 in channel
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(3)

ds1ChannelCellMapping		3.1.1751.2.18.3.3.1.4
cell delineation mode for ATM cell bearing services
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	directMapping(1), none(2)

ds1ChannelInputCodingRule		3.1.1751.2.18.3.3.1.5
enhancement feature
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLawPCM(2), aLawPCM(3), digital(4)

ds1ChannelSecuFeature		3.1.1751.2.18.3.3.1.6
enhancement feature
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsecurable(1), secured(2), securable(3)

ds1ChannelSignaling		3.1.1751.2.18.3.3.1.7
refers to robbed-bit signaling in circuitEmulation interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ds1ChannelCellScramble		3.1.1751.2.18.3.3.1.8
refers to enabling/disabling cell scrambling on ATM interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

msChannelConfigTable		3.1.1751.2.18.3.4
Channel configuration table for multi-serial ports.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MsChannelConfigEntry

msChannelConfigEntry		3.1.1751.2.18.3.4.1
Row definition for multi-serial channel config.
Status: current	Access: not-accessible
OBJECT-TYPE
	MsChannelConfigEntry

msChannelId		3.1.1751.2.18.3.4.1.1
interface index - SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

msChannelIfType		3.1.1751.2.18.3.4.1.2
interface type for multi-serial port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), atmUni3-0(2), atmUni3-1(3), iispUser(4), iispNetwork(5), circuitEmulation(6), terminalEmulation(7), frameRelayUni(8), hdlcPassThrough(9), frameRelayNni(10), atmPnni1-0(11), atmUni4-0(12)

msChannelCellBearingMode		3.1.1751.2.18.3.4.1.3
The cell delineation mode is either LANET or CCITT based
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	lanet(1), ccittDirectMapping(2), none(3)

msChannelCellBearingAddrMode		3.1.1751.2.18.3.4.1.4
standard - ATM Forum UNI 3.0/3.1 noiseTolerant - A proprietary noise tolerant address mapping scheme
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	standard(1), noiseTolerant(2)

msChannelCellBearingPayloadFec		3.1.1751.2.18.3.4.1.5
payload error correction scheme
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	dynamic(1), threeEighthsRate(2), oneQuarterRate(3), oneEighthRate(4)

msChannelSecuFeature		3.1.1751.2.18.3.4.1.6
enhancement feature
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsecurable(1), secured(2), securable(3)

oc3ChannelConfigTable		3.1.1751.2.18.3.5
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Oc3ChannelConfigEntry

oc3ChannelConfigEntry		3.1.1751.2.18.3.5.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	Oc3ChannelConfigEntry

oc3ChannelId		3.1.1751.2.18.3.5.1.1
interface index - SSPPCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

oc3ChannelIfType		3.1.1751.2.18.3.5.1.2
UNI or NNI type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), atmUni3-0(2), atmUni3-1(3), iispUser(4), iispNetwork(5), atmPnni1-0(6), atmUni4-0(7), atmVnnUni3-1(8)

oc3ChannelSecuFeature		3.1.1751.2.18.3.5.1.3
enhancement feature
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsecurable(1), secured(2), securable(3)

twoWireSourceChannelConfigTable		3.1.1751.2.18.3.6
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TwoWireSourceChannelConfigEntry

twoWireSourceChannelConfigEntry		3.1.1751.2.18.3.6.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	TwoWireSourceChannelConfigEntry

twoWireSourceChannelId		3.1.1751.2.18.3.6.1.1
interface index - SSPPCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

twoWireSourceChannelIfType		3.1.1751.2.18.3.6.1.2
Interface types of 2W station(source) channel.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), circuitEmulation(2)

twoWireSourceChannelConnectionType		3.1.1751.2.18.3.6.1.3
This field selects ATM virtual circuit connection type, PVC or SVC.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pvc(1), svc(2)

twoWireSourceChannelCompandingLaw		3.1.1751.2.18.3.6.1.4
This field selects channel encoding/decoding quantization interval, muLaw or aLaw.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	muLawPCM(1), aLawPCM(2)

twoWireSourceChannelSecuFeature		3.1.1751.2.18.3.6.1.5
enhancement feature
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unsecurable(1), secured(2), securable(3)

twoWireSourceChannelVoiceCompression		3.1.1751.2.18.3.6.1.6
voice compression scheme
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), adpcm32k(2), adpcm16k(3), adpcm8k(4)

twoWireSourceChannelEchoCancellation		3.1.1751.2.18.3.6.1.7
This field disables/enables twoWireSource card echo cancellation function.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

twoWireSourceChannelSilenceSupression		3.1.1751.2.18.3.6.1.8
This field disables/enables twoWireSource card silence suppression.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

twoWireSourceChannelEncapsulationAal		3.1.1751.2.18.3.6.1.9
This field selects ATM cell payload format. Aal1 - ATM Adaption Layer Type 1. Yurie - A proprietary specific ATM cell payload format for compressed data.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	aal1(1), lucent(2)

twoWireSourceChannelSubscriberService		3.1.1751.2.18.3.6.1.10
This field selects subscribed channel service types. plar - Private Line Automatic Ring fxs - Foreign Exchange Subscriber End s-signaling - A proprietary specific signaling type based on AIN model.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	plar(1), fxs(2), s-signaling(3)

highSpeedChannelConfigTable		3.1.1751.2.18.3.7
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HighSpeedChannelConfigEntry

highSpeedChannelConfigEntry		3.1.1751.2.18.3.7.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	HighSpeedChannelConfigEntry

highSpeedChannelId		3.1.1751.2.18.3.7.1.1
interface index - SSPPCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

highSpeedChannelIfType		3.1.1751.2.18.3.7.1.2
UNI or NNI type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), atmUni3-0(2), atmUni3-1(3), iispUser(4), iispNetwork(5), circuitEmulation(6), atmUni4-0(7)

dspChannelConfigTable		3.1.1751.2.18.3.8
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DspChannelConfigEntry

dspChannelConfigEntry		3.1.1751.2.18.3.8.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	DspChannelConfigEntry

dspChannelId		3.1.1751.2.18.3.8.1.1
interface index - SSPPCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

dspChannelIfType		3.1.1751.2.18.3.8.1.2
Channel Interface Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), dsp(2)

dspChannelInputCodingRule		3.1.1751.2.18.3.8.1.3
Input Coding Rule
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	muLawPCM(1)

dspChannelVoiceCompression		3.1.1751.2.18.3.8.1.4
voice compression scheme
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	adpcm32k(1), adpcm16k(2)

dspChannelEchoCancellation		3.1.1751.2.18.3.8.1.5
voice compression scheme
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1)

dspChannelSilenceSupression		3.1.1751.2.18.3.8.1.6
voice compression scheme
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1)

twoWireSinkChannelConfigTable		3.1.1751.2.18.3.9
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TwoWireSinkChannelConfigEntry

twoWireSinkChannelConfigEntry		3.1.1751.2.18.3.9.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	TwoWireSinkChannelConfigEntry

twoWireSinkChannelId		3.1.1751.2.18.3.9.1.1
interface index - SSPPCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

twoWireSinkChannelIfType		3.1.1751.2.18.3.9.1.2
Interface types.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), circuitEmulation(2)

twoWireSinkChannelConnectionType		3.1.1751.2.18.3.9.1.3
This field selects ATM virtual circuit connection type, PVC or SVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	pvc(1), svc(2)

twoWireSinkChannelCompandingLaw		3.1.1751.2.18.3.9.1.4
This field selects channel encoding/decoding quantization interval, muLaw or aLaw.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	muLawPCM(1), aLawPCM(2)

twoWireSinkChannelVoiceCompression		3.1.1751.2.18.3.9.1.5
voice compression scheme
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), adpcm32k(2), adpcm16k(3), adpcm8k(4)

twoWireSinkChannelEchoCancellation		3.1.1751.2.18.3.9.1.6
This field disables/enables twoWireSink card echo cancellation function.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

twoWireSinkChannelSilenceSupression		3.1.1751.2.18.3.9.1.7
This field disables/enables twoWireSink card silence suppression.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

twoWireSinkChannelEncapsulationAal		3.1.1751.2.18.3.9.1.8
This field selects ATM cell payload format. Aal1 - ATM Adaption Layer Type 1. Yurie - A proprietary specific ATM cell payload format for compressed data.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	aal1(1), lucent(2)

twoWireSinkChannelSubscriberService		3.1.1751.2.18.3.9.1.9
The only available service type for twoWireSink card is Foreign Exchange Office End (fxo).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	fxo(1)

e3ChannelConfigTable		3.1.1751.2.18.3.10
Table of common physical channel attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		E3ChannelConfigEntry

e3ChannelConfigEntry		3.1.1751.2.18.3.10.1
Row definition for common physical channel attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	E3ChannelConfigEntry

e3ChannelId		3.1.1751.2.18.3.10.1.1
interface index - SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

e3ChannelIfType		3.1.1751.2.18.3.10.1.2
Interface type configured on E3 channel
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), atmUni3-0(2), atmUni3-1(3), iispUser(4), iispNetwork(5), atmPnni1-0(6), atmUni4-0(7), circuitEmulation(8)

e3ChannelSecuFeature		3.1.1751.2.18.3.10.1.3
enhancement feature
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsecurable(1), secured(2), securable(3)

e1ChannelConfigTable		3.1.1751.2.18.3.11
Table of common physical Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		E1ChannelConfigEntry

e1ChannelConfigEntry		3.1.1751.2.18.3.11.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	E1ChannelConfigEntry

e1ChannelId		3.1.1751.2.18.3.11.1.1
interface index - SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

e1ChannelIfType		3.1.1751.2.18.3.11.1.2
UNI or NNI type for ATM ,Frame Relay, or ISDN serviceinterface type for channel
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), atmUni3-0(2), atmUni3-1(3), iispUser(4), iispNetwork(5), circuitEmulation(6), frameRelayUni(7), hdlcPassThrough(8), frameRelayNni(9), atmIma(10), atmPnni1-0(11), pri-isdn-network(12), pri-isdn-user(13), casTrunkLine(14), atmUni4-0(15)

e1ChannelDs0Map		3.1.1751.2.18.3.11.1.3
bit map of DS0 in channel
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

e1ChannelCellMapping		3.1.1751.2.18.3.11.1.4
cell delineation mode for ATM cell bearing services
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	directMapping(1), none(2)

e1ChannelInputCodingRule		3.1.1751.2.18.3.11.1.5
enhancement feature
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLawPCM(2), aLawPCM(3), digital(4)

e1ChannelSecuFeature		3.1.1751.2.18.3.11.1.6
enhancement feature
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsecurable(1), secured(2), securable(3)

e1ChannelSignaling		3.1.1751.2.18.3.11.1.7
Refers to robbed-bit singaling in circuitEmulation interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ethernetChannelConfigTable		3.1.1751.2.18.3.12
Table used for enthernet channel configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthernetChannelConfigEntry

ethernetChannelConfigEntry		3.1.1751.2.18.3.12.1
Row definition for enthernet channel attributes.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthernetChannelConfigEntry

ethernetChannelId		3.1.1751.2.18.3.12.1.1
Interface index
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ethernetChannelIfType		3.1.1751.2.18.3.12.1.2
Types of ethernet interface. There are two types of bridging interface(channel):bridge and routing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), bridge(2), routing(3)

dsp2Channel		3.1.1751.2.18.3.13
OBJECT IDENTIFIER

dsp2ChannelConfigTable		3.1.1751.2.18.3.13.1
Table of Channel attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsp2ChannelConfigEntry

dsp2ChannelConfigEntry		3.1.1751.2.18.3.13.1.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsp2ChannelConfigEntry

dsp2ChannelId		3.1.1751.2.18.3.13.1.1.1
interface index - SSPPCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

dsp2ChannelIfType		3.1.1751.2.18.3.13.1.1.2
Channel Interface Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), dsp2(2)

dsp2ChannelAlarmType		3.1.1751.2.18.3.13.1.1.3
This field is a read only failure which gives the status of a dsp.When the status is dspFailure the Operational Status at the interface level will go OOS
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), dspFailure(2)

dsp2ChannelModeConfig		3.1.1751.2.18.3.13.1.1.4
This field is used to configure the mode of the DSP card. Each mode corresponds to a set of algorithms supported by the IO card. The complete list of enumerations of supported algorithms is given in the dsp2AlgorithmTable. The following description outlines the algorithms supported in each corresponding AlgoSet. algoSet1 : g168-echo-cancellation128ms algoSet2 : g726-voice-compression, g165-echo-cancellation, generic-silence-suppression, fax-modem-tone-detection, g168-echo-cancellation64ms. algoSet3 : g729a-voice-compression, g165-echo-cancellation, g729b-silence-suppression, fax-modem-tone-detection, g168-echo-cancellation64ms. algoSet4 : v17-fax-algorithm-upto-14400-bps, v29-fax-algorithm-upto-9600-bps, v27ter-fax-algorithm-upto-2400-bps, v21-fax-algorithm-upto-300-bps. algoSet5 : g168-echo-cancellation64ms. algoSet6 : g726-voice-compression, g729a-voice-compression, g729b-silence-suppression, g168-echo-cancellation64ms, v17-fax-algorithm-upto-14400-bps, v29-fax-algorithm-upto-9600-bps, v27ter-fax-algorithm-upto-2400-bps, v21-fax-algorithm-upto-300-bps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	algoSet1(1), algoSet2(2), algoSet3(3), algoSet4(4), algoSet5(5), algoSet6(6)

dsp2AlgorithmTable		3.1.1751.2.18.3.13.2
Table of dsp2 algorithms assigned to interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsp2AlgorithmEntry

dsp2AlgorithmEntry		3.1.1751.2.18.3.13.2.1
Row definition for dsp2 algorithms assigned to interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsp2AlgorithmEntry

dsp2AlgorithmId		3.1.1751.2.18.3.13.2.1.1
interface index - SSPPCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

dsp2AlgorithmType		3.1.1751.2.18.3.13.2.1.2
DSP Algorithm type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	g726-voice-compression(1), g165-echo-cancellation(2), generic-silence-suppression(3), fax-modem-tone-detection(4), g729a-voice-compression(5), g729b-silence-suppression(6), g168-echo-cancellation64ms(7), g168-echo-cancellation128ms(8), v17-fax-algorithm-upto-14400-bps(9), v29-fax-algorithm-upto-9600-bps(10), v27ter-fax-algorithm-upto-2400-bps(11), v21-fax-algorithm-upto-300-bps(12)

imaGrpChannelConfigTable		3.1.1751.2.18.3.14
Table used for the IMA virtual channel (group) configuration on cards that have physical interfaces configured as atmIma. Represents three channels that can be configured as IMA groups on port 7 of DS1 and E1 cards.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ImaGrpChannelConfigEntry

imaGrpChannelConfigEntry		3.1.1751.2.18.3.14.1
Row definition for common physical port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	ImaGrpChannelConfigEntry

imaGrpChannelId		3.1.1751.2.18.3.14.1.1
interface index - SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

imaGrpChannelIfType		3.1.1751.2.18.3.14.1.2
interface type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), atmUni3-0(2), atmUni3-1(3), iispUser(4), iispNetwork(5), atmPnni1-0(6), atmUni4-0(7)

imaGrpChannelPortMap		3.1.1751.2.18.3.14.1.3
A bitmap that identifies the physical IMA interfaces in this group. The least significant bit represents port 1.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

imaGrpChannelNeState		3.1.1751.2.18.3.14.1.4
The current operational state of the near-end IMA Group State Machine.
Status: current	Access: read-only
OBJECT-TYPE
	ImaGrpChannelEndState

imaGrpChannelFeState		3.1.1751.2.18.3.14.1.5
The current operational state of the far-end IMA Group State Machine.
Status: current	Access: read-only
OBJECT-TYPE
	ImaGrpChannelEndState

imaGrpChannelFailureStatus		3.1.1751.2.18.3.14.1.6
The current failure status of the IMA group (the reason why the GTSM is in the down state). noFailure(1) no failure startUpNe(2) near-end is in the state of start-up startUpFe(3) far-end is in the state of start-up invalidMValueNe(4) near-end has invalid frame length invalidMValueFe(5) far-end has invalid frame length failedAssymetricNe(6) near-end failed due to incompatable symmetry failedAssymetricFe(7) far-end failed due to incompatable symmetry insuffLinksNe(8) Near-end reported less than the min number of Tx links are active or less than the min number of Rx links are active insuffLinksFe(9) Far-end reported less than the min number of Rx links are active or less than thenmin number of Tx links are active blockedNe(10) Near-end is administratively out-of-service blockedFe(11) Far-end is administratively out-of-service otherFailure(12) other failures
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noFailure(1), startUpNe(2), startUpFe(3), invalidMValueNe(4), invalidMValueFe(5), failedAssymetricNe(6), failedAssymetricFe(7), insuffLinksNe(8), insuffLinksFe(9), blockedNe(10), blockedFe(11), otherFailure(12)

imaGrpChannelSymmetry		3.1.1751.2.18.3.14.1.7
Symmetry of the IMA group. Symmetric configuration: all ports of IMA group are configured as full-duplex. With symmetric configuration, operation is symmetric if no links failes; is asymmetric if a link fails so that the active forward and backward links between far-end and near-end are asymmetric. If the configuration is asymmetric, the operation can never be symmetric.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	symOperation(1), asymOperation(2), asymConfiguration(3)

imaGrpChannelMinNumTxLinks		3.1.1751.2.18.3.14.1.8
Minimum number of transmit links required to be Active for the IMA group to be in the Up state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..32

imaGrpChannelMinNumRxLinks		3.1.1751.2.18.3.14.1.9
Minimum number of receive links required to be Active for the IMA group to be in the Up state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..32

imaGrpChannelNeTxClkMode		3.1.1751.2.18.3.14.1.10
Transmit clocking mode used by the near-end IMA group. There are two possible modes: the Common Transmit Clock (CTC) and the Independent Transmit Clock (ITC). The CTC mode corresponds to the case when the transmit clock of all IMA links are derived from the same source. The ITC configuration corresponds to the case where there is at least one IMA link whose transmit clock is derived from a source different than at least another link transmit clock. The underlying clock configuration must be set up by the user to ensure operation in the selected mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ctc(1), itc(2)

imaGrpChannelFeTxClkMode		3.1.1751.2.18.3.14.1.11
Transmit clocking mode used by the far-end IMA group. There are two possible modes: the Common Transmit Clock (CTC) and the Independent Transmit Clock (ITC). The CTC mode corresponds to the case when the transmit clock of all IMA links are derived from the same source. The ITC configuration corresponds to the case where there is at least one IMA link whose transmit clock is derived from a source different than at least another link transmit clock.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ctc(1), itc(2)

imaGrpChannelTxImaId		3.1.1751.2.18.3.14.1.12
The IMA ID currently in use by the near-end IMA function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

imaGrpChannelRxImaId		3.1.1751.2.18.3.14.1.13
The IMA ID currently in use by the far-end IMA function.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

imaGrpChannelTxFrameLength		3.1.1751.2.18.3.14.1.14
The frame length to be used by the IMA group in the transmit direction. Can only be set when the IMA group is startup.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	m32(32), m64(64), m128(128), m256(256)

imaGrpChannelRxFrameLength		3.1.1751.2.18.3.14.1.15
Value of IMA frame length as received from remote IMA function.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	m32(32), m64(64), m128(128), m256(256)

imaGrpChannelDiffLinkDelayMax		3.1.1751.2.18.3.14.1.16
The maximum number of milliseconds of delay differential among the links that will be tolerated on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..200

imaGrpChannelLeastDelayLink		3.1.1751.2.18.3.14.1.17
The Interface Index of the link configured in the IMA group which has the smallest link propagation delay. This value has meaning only if at least 1 link has been configured in the IMA group.
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

imaGrpChannelDiffDelayMaxObs		3.1.1751.2.18.3.14.1.18
The latest maximum differential delay observed (in milliseconds), i.e. between the links having the least and most link propagation delay, among the receive links that are currently configured in the IMA group.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

imaGrpChannelAlphaValue		3.1.1751.2.18.3.14.1.19
This indicates the 'alpha' value used to specify the number of consecutive invalid ICP cells to be detected before moving to the IMA HUNT state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..2

imaGrpChannelBetaValue		3.1.1751.2.18.3.14.1.20
This indicates the 'beta' value used to specify the number of consecutive errored ICP cells to be detected before moving to the IMA HUNT state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..5

imaGrpChannelGammaValue		3.1.1751.2.18.3.14.1.21
This indicates the 'gamma' value used to specify the number of consecutive valid ICP cells to be detected before moving to the IMA SYNC state from the PRESYNC state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..5

imaGrpChannelStatsNeNumFailures		3.1.1751.2.18.3.14.1.22
The number of times a near-end group failure (Config-Abort, Insufficient-Links) has been reported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

imaGrpChannelStatsFeNumFailures		3.1.1751.2.18.3.14.1.23
The number of times a far-end group failure (Config-Abort-FE, Insufficient-Links-FE, Blocked-FE) has been reported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

imaGrpChannelStatsNumTxActLnks		3.1.1751.2.18.3.14.1.24
The number of links which are configured to transmit and are currently Active in this IMA group.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

imaGrpChannelStatsNumRxActLnks		3.1.1751.2.18.3.14.1.25
The number of links which are configured to receive and are currently Active in this IMA group.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

imaGrpChannelStatsTimer		3.1.1751.2.18.3.14.1.26
Time, in seconds, since last reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

imaGrpChannelCompatMode		3.1.1751.2.18.3.14.1.27
This is used to indicate interoperability mode to the I/O card in terms of reporting the link status at the correct location in the IMA Control Protocol (ICP) cell
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

tasmChannelConfigTable		3.1.1751.2.18.3.15
Table of common physical Channel attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TasmChannelConfigEntry

tasmChannelConfigEntry		3.1.1751.2.18.3.15.1
Row definition for common physical channel attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	TasmChannelConfigEntry

tasmChannelId		3.1.1751.2.18.3.15.1.1
Interface index - SSPPCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

tasmChannelIfType		3.1.1751.2.18.3.15.1.2
Channel Interface Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconfigured(1), toneAnnce(2)

tasmChannelAlarmType		3.1.1751.2.18.3.15.1.3
This field is a read only failure which gives the status of a DSP in the TASM card.When the status is tasmFailure the Operational Status at the interface level will go OOS
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), tasmFailure(2)

tasmChannelModeConfig		3.1.1751.2.18.3.15.1.4
This field is used to configure the mdoe in which a TASM DSP will be used asd a resource. The modes are explained as follows: casMode: DSP resource is used for DTMF/MF tone detection/generation and running the Type 100, 105, and 108 tests. tasMode: DSP resource is used for playing/compressing announcement.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	casMode(1), tasMode(2)

atmUniConfigTable		3.1.1751.2.18.5.1
Table of atm user to network interface (UNI)
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmUniConfigEntry

atmUniConfigEntry		3.1.1751.2.18.5.1.1
Row definition of atm UNI
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmUniConfigEntry

atmUniIfIndex		3.1.1751.2.18.5.1.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmUniAddrType		3.1.1751.2.18.5.1.1.2
atm address type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nsap(1), e164(2), private(3)

atmUniSvcMinVpi		3.1.1751.2.18.5.1.1.3
The lower bound of the VPI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmUniSvcMaxVpi		3.1.1751.2.18.5.1.1.4
The upper bound of the VPI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmUniSvcMinVci		3.1.1751.2.18.5.1.1.5
The lower bound of the VCI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmUniSvcMaxVci		3.1.1751.2.18.5.1.1.6
The upper bound of the VCI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmUniAdminStatus		3.1.1751.2.18.5.1.1.7
The administrative action: 'outOfService' means take the UNI out of service 'inService' means take the UNI in service 'delete' remove/deconfigure the UNI.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

atmUniOperStatus		3.1.1751.2.18.5.1.1.8
The operational status of the UNI: 'outOfService' means the UNI is out of service 'inService' means the UNI is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmUniNwPrefix1		3.1.1751.2.18.5.1.1.9
ATM Network Prefix 1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(13)

atmUniOverSubscription		3.1.1751.2.18.5.1.1.10
Over subscription factor
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

atmUniT303		3.1.1751.2.18.5.1.1.11
Timer T303 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniT308		3.1.1751.2.18.5.1.1.12
Timer T308 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniT309		3.1.1751.2.18.5.1.1.13
Timer T309 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniT310		3.1.1751.2.18.5.1.1.14
Timer T310 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniT313		3.1.1751.2.18.5.1.1.15
Timer T313 value - User side only - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniT316		3.1.1751.2.18.5.1.1.16
Timer T316 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniT317		3.1.1751.2.18.5.1.1.17
Timer T317 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniT322		3.1.1751.2.18.5.1.1.18
Timer T322 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniT398		3.1.1751.2.18.5.1.1.19
Timer T398 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniT399		3.1.1751.2.18.5.1.1.20
Timer T399 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniMyNeighborIpAddress		3.1.1751.2.18.5.1.1.21
The IP address of the neighbor system connected to the far end of this interface, to which a Network Management Station can send SNMP messages, as IP datagrams sent to UDP port 161, in order to access network management information concerning the operation of that system. Note that the value of this object can currently only be obtained by manual configuration.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

atmUniMyNeighborIfName		3.1.1751.2.18.5.1.1.22
The textual name of the interface on the neighbor system on the far end of this interface, and to which this interface connects. If the neighbor system is manageable through SNMP and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. If this interface does not have a textual name, the value of this object is a zero length string. Note that the value of this object can currently only be obtained by manual configuration.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

atmUniVpiSig		3.1.1751.2.18.5.1.1.23
VPI value for the signalling channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmUniVciSig		3.1.1751.2.18.5.1.1.24
VCI value for the signalling channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..31

atmUniVpiIlmi		3.1.1751.2.18.5.1.1.25
VPI value for the ilmi channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmUniVciIlmi		3.1.1751.2.18.5.1.1.26
VCI value for the ilmi channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..31

atmUniAtmSignalingStatus		3.1.1751.2.18.5.1.1.27
Indicates if atm signaling is enabled or disabled for this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmUniMyIfName		3.1.1751.2.18.5.1.1.29
A textual name of this interface. If this system is manageable manageable through SNMP and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. This interface must be uniquely named on this system to distinguish parallel links with a neighboring system. If this interface does not have a textual name, the value of this object is a zero length string.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

atmUniIlmiProtocolStatus		3.1.1751.2.18.5.1.1.30
The administrative status: 'enabled' - ILMI protocol enabled on UNI 'disabled' - ILMI protocol disabled on UNI.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmUniIlmiOperStatus		3.1.1751.2.18.5.1.1.31
The operational status: 'outOfService' - ILMI connectivity is down 'inService' - ILMI connectivity is up.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmUniIlmiConfigProc		3.1.1751.2.18.5.1.1.32
ILMI Configuration Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmUniIlmiConnectProc		3.1.1751.2.18.5.1.1.33
ILMI Connectivity Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmUniIlmiAttachPtProc		3.1.1751.2.18.5.1.1.34
ILMI Attachment Point Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmUniIlmiSecureLinkProc		3.1.1751.2.18.5.1.1.35
ILMI Secure Link Procedure status. Can be enabled only if Attachment Point Procedure is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmUniIlmiAddrRegProc		3.1.1751.2.18.5.1.1.36
ILMI Address Registration Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmUniIlmiTimerS		3.1.1751.2.18.5.1.1.37
Timer S (secs). Used to poll peer when link is down.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniIlmiTimerT		3.1.1751.2.18.5.1.1.38
Timer T (secs). Used to poll peer when link is up.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniIlmiRetryK		3.1.1751.2.18.5.1.1.39
Retry K - number of timeouts before link is declared down.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmUniIntfType		3.1.1751.2.18.5.1.1.40
atm interface type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	user(1), network(2)

atmUniUserAddress		3.1.1751.2.18.5.1.1.41
ATM User Address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(7)

atmUniViSuppFlag		3.1.1751.2.18.5.1.1.42
virtual interface supp off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmUniUPCSupp		3.1.1751.2.18.5.1.1.43
upc supp off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmUniUbrLoadBalSupp		3.1.1751.2.18.5.1.1.44
load balancing supp for ubr conns off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmUniAvailBwIgr		3.1.1751.2.18.5.1.1.45
The Avail Bandwidth for that interface in cells per sec. Bandwidth for UBR conns will not be accounted for
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmUniAvailBwEgr		3.1.1751.2.18.5.1.1.46
The Avail Bandwidth for that interface in cells per sec which can go out of the interface. Bandwidth for UBR conns will not be accounted for
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmUniVUNISuppFlag		3.1.1751.2.18.5.1.1.47
virtual UNI interface supp off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmUniUserAddrOrgScope		3.1.1751.2.18.5.1.1.48
ATM User Address Organizational scope
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	localNetwork(1), localNetworkPlusOne(2), localNetworkPlusTwo(3), siteMinusOne(4), intraSite(5), sitePlusOne(6), organizationMinusOne(7), intraOrganization(8), organizationPlusOne(9), communityMinusOne(10), intraCommunity(11), communityPlusOne(12), regional(13), interRegional(14), global(15)

atmUniSscopRxWndSz		3.1.1751.2.18.5.1.1.49
The receive window size for the SSCOP layer
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	8..256

atmUniConnTrafficShapingFlag		3.1.1751.2.18.5.1.1.50
Traffic Shaping for Conn was enabled primarily because the core would lose cells since we were non-conformant cells. Therefore the hardware added traffic shaping per connection. But condition is VI should not be enabled if this feature is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmIispConfigTable		3.1.1751.2.18.5.2
Table of atm iisp interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmIispConfigEntry

atmIispConfigEntry		3.1.1751.2.18.5.2.1
Row definition of atm iisp interface
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmIispConfigEntry

atmIispIfIndex		3.1.1751.2.18.5.2.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmIispSvcMinVpi		3.1.1751.2.18.5.2.1.2
The lower bound of the VPI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

atmIispSvcMaxVpi		3.1.1751.2.18.5.2.1.3
The upper bound of the VPI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

atmIispSvcMinVci		3.1.1751.2.18.5.2.1.4
The lower bound of the VCI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmIispSvcMaxVci		3.1.1751.2.18.5.2.1.5
The upper bound of the VCI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmIispAdminStatus		3.1.1751.2.18.5.2.1.6
The administrative action: 'outOfService' means take the UNI out of service 'inService' means take the UNI in service 'delete' remove/deconfigure the UNI.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

atmIispOperStatus		3.1.1751.2.18.5.2.1.7
The operational status of the UNI: 'outOfService' means the UNI is out of service 'inService' means the UNI is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmIispOverSubscription		3.1.1751.2.18.5.2.1.8
Over subscription factor
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

atmIispT303		3.1.1751.2.18.5.2.1.9
Timer value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmIispT308		3.1.1751.2.18.5.2.1.10
Timer value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmIispT309		3.1.1751.2.18.5.2.1.11
Timer value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmIispT310		3.1.1751.2.18.5.2.1.12
Timer value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmIispT316		3.1.1751.2.18.5.2.1.13
Timer value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmIispT317		3.1.1751.2.18.5.2.1.14
Timer value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmIispT322		3.1.1751.2.18.5.2.1.15
Timer value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmIispT398		3.1.1751.2.18.5.2.1.16
Timer value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmIispT399		3.1.1751.2.18.5.2.1.17
Timer value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmIispAtmSignalingStatus		3.1.1751.2.18.5.2.1.18
Indicates if atm signaling is enabled or disabled for this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmIispAvailBwIgr		3.1.1751.2.18.5.2.1.19
The Avail Bandwidth for that interface in cells per sec. Bandwidth for UBR conns will not be accounted for.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIispAvailBwEgr		3.1.1751.2.18.5.2.1.20
The Avail Bandwidth for that interface in cells per sec. Bandwidth for UBR conns will not be accounted for.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIispUPCSupp		3.1.1751.2.18.5.2.1.21
upc supp off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmIispUbrLoadBalSupp		3.1.1751.2.18.5.2.1.22
load balancing supp for ubr conns off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmIispSscopRxWndSz		3.1.1751.2.18.5.2.1.23
The receive window size for the SSCOP layer
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	8..256

atmIispConnTrafficShapingFlag		3.1.1751.2.18.5.2.1.24
Traffic Shaping for Conn was enabled primarily because the core would lose cells since we were non-conformant cells. Therefore the hardware added traffic shaping per connection. But condition is VI should not be enabled if this feature is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmCirEmConfigTable		3.1.1751.2.18.5.3
Table for ATM Circuit Emulation Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmCirEmConfigEntry

atmCirEmConfigEntry		3.1.1751.2.18.5.3.1
Row definition for ATM Circuit Emulation interface
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmCirEmConfigEntry

atmCirEmIfIndex		3.1.1751.2.18.5.3.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmCirEmAdminStatus		3.1.1751.2.18.5.3.1.2
The administrative action: 'outOfService' take the interface out of service 'inService' take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

atmCirEmOperStatus		3.1.1751.2.18.5.3.1.3
The operational status of the interface: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmCirEmCASIdleAbcdPattern		3.1.1751.2.18.5.3.1.4
abcd bit pattern for cirEm AIS
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..15

atmCirEmCASBusyAbcdPattern		3.1.1751.2.18.5.3.1.5
abcd bit pattern for cirEm RDI
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..15

atmCirEmAlarmDataPattern		3.1.1751.2.18.5.3.1.6
data pattern for cirEm AIS
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmCirEmTCPattern		3.1.1751.2.18.5.3.1.7
Should abcd bits be toggled after 2.5 Secs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	casIdle(1), casBusy(2)

atmCirEmDownStInterworking		3.1.1751.2.18.5.3.1.8
This field will be used to select the type of interworking to be done in the down stream direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unSupp(1), oAM(2), trunkCond(3)

atmTermEmConfigTable		3.1.1751.2.18.5.4
Table for ATM Terminal Emulation Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmTermEmConfigEntry

atmTermEmConfigEntry		3.1.1751.2.18.5.4.1
Row definition for ATM Terminal Emulation interface
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmTermEmConfigEntry

atmTermEmIfIndex		3.1.1751.2.18.5.4.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmTermEmRxTimeOut		3.1.1751.2.18.5.4.1.2
receive timeout value in tenths of seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	7..10

atmTermEmAdminStatus		3.1.1751.2.18.5.4.1.3
The administrative action: 'outOfService' take the interface out of service 'inService' take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

atmTermEmOperStatus		3.1.1751.2.18.5.4.1.4
The operational status of the interface: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

hdlcConfigTable		3.1.1751.2.18.5.5
Table for an HDLC Pass Through Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HdlcConfigEntry

hdlcConfigEntry		3.1.1751.2.18.5.5.1
Row definition for an HDLC Pass Through interface
Status: current	Access: not-accessible
OBJECT-TYPE
	HdlcConfigEntry

hdlcIfIndex		3.1.1751.2.18.5.5.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

hdlcAdminStatus		3.1.1751.2.18.5.5.1.2
The administrative action: 'outOfService' means take the interface out of service 'inService' means take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

hdlcOperStatus		3.1.1751.2.18.5.5.1.3
The operational status of the interface: 'outOfService' means the interface is out of service 'inService' means the interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

hdlcThroughPut		3.1.1751.2.18.5.5.1.4
The throughput bandwidth of the interface: 'k64' means a throughput of 64 kb 'k56' means a throughput of 56 kb
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	k64(1), k56(2)

hdlcDataInversion		3.1.1751.2.18.5.5.1.5
Flag indicating whether data inversion is performed by the IO card for this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

frUniConfigTable		3.1.1751.2.18.5.6
Table for Frame Realy UNI Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrUniConfigEntry

frUniConfigEntry		3.1.1751.2.18.5.6.1
Row definition for Frame Relay interface
Status: current	Access: not-accessible
OBJECT-TYPE
	FrUniConfigEntry

frUniIfIndex		3.1.1751.2.18.5.6.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frUniAddrDlciLen		3.1.1751.2.18.5.6.1.2
Length of Data Link connection identify of frame relay UNI address
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	twoOctets10Bits(1)

frUniDlcmiState		3.1.1751.2.18.5.6.1.3
The state of Data Link Connection Management Indentify of frame relay UNI.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noLmi(1), lmiDte(2), lmiDce(3), lmiNni(4)

frUniAdminStatus		3.1.1751.2.18.5.6.1.4
The administrative action: 'outOfService' take the interface out of service 'inService' take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

frUniOperStatus		3.1.1751.2.18.5.6.1.5
The operational status of the interface: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

frUniOverSubscription		3.1.1751.2.18.5.6.1.6
Allow for the 'reserved' bandwidth allocated to oversubscribe the line by up to a factor of 10 . Generally, a figure of between 1 and 4 is normally a safe bet, although higher levels are often acceptable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

frUniLmiProtocol		3.1.1751.2.18.5.6.1.7
Lmi protocol to run
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), ccitt(2), ansi(3), att(4)

frUniInterworkingType		3.1.1751.2.18.5.6.1.8
frf5 - fr/atm network interworking frf8 - fr/atm service interworking
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	frf5(1), frf8(2)

frUniN391		3.1.1751.2.18.5.6.1.9
full status polling counter. DTE:Mandatory, DCE:N/A
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

frUniN392		3.1.1751.2.18.5.6.1.10
error threshold. DTE:Mandatory, DCE:Mandatory
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

frUniN393		3.1.1751.2.18.5.6.1.11
Monitored event count. DTE:Mandatory, DCE:N/A
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

frUniT391		3.1.1751.2.18.5.6.1.12
Link integrity verification timer. DTE:Mandatory, DCE:N/A
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..30

frUniT392		3.1.1751.2.18.5.6.1.13
Polling verification timer. DTE:N/A, DCE:Mandatory
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..30

frUniAsyncLmi		3.1.1751.2.18.5.6.1.14
Async PVC status messages
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

frLmiOperStatus		3.1.1751.2.18.5.6.1.15
The operational status of the lmi protocol: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

frUniNT3		3.1.1751.2.18.5.6.1.16
Message frequency timer relevant for ATT LMI only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..30

frUniThroughPut		3.1.1751.2.18.5.6.1.17
The throughput bandwidth of the interface: 'k64' means a throughput of 64 kb 'k56' means a throughput of 56 kb
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	k64(1), k56(2)

dspConfigTable		3.1.1751.2.18.5.7
Table for Dsp Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DspConfigEntry

dspConfigEntry		3.1.1751.2.18.5.7.1
Row definition for Dsp interface
Status: current	Access: not-accessible
OBJECT-TYPE
	DspConfigEntry

dspIfIndex		3.1.1751.2.18.5.7.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

dspAdminStatus		3.1.1751.2.18.5.7.1.2
The administrative action: 'outOfService' take the interface out of service 'inService' take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

dspOperStatus		3.1.1751.2.18.5.7.1.3
The operational status of the interface: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

bridgeConfigTable		3.1.1751.2.18.5.8
Table which hold Config Entries for all bridges.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BridgeConfigEntry

bridgeConfigEntry		3.1.1751.2.18.5.8.1
Row definition for bridge entries
Status: current	Access: not-accessible
OBJECT-TYPE
	BridgeConfigEntry

bridgeIfIndex		3.1.1751.2.18.5.8.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bridgeAdminStatus		3.1.1751.2.18.5.8.1.2
The administrative action: 'outOfService' take the interface out of service 'inService' take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

bridgeOperStatus		3.1.1751.2.18.5.8.1.3
The operational status of the interface: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

bridgeNumber		3.1.1751.2.18.5.8.1.4
The number of bridges
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..999

bridgePortPriority		3.1.1751.2.18.5.8.1.5
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of dot1dStpPort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

bridgePathCost		3.1.1751.2.18.5.8.1.6
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802-1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

bridgeConnectionType		3.1.1751.2.18.5.8.1.7
Connection types
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	vc(1), llc(2)

bridgeDomainTable		3.1.1751.2.18.5.9
A table which holds the bridgeDomainEntry data
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BridgeDomainEntry

bridgeDomainEntry		3.1.1751.2.18.5.9.1
A table entry for a Bridge Domain on an ethernet card
Status: current	Access: not-accessible
OBJECT-TYPE
	BridgeDomainEntry

bridgeDomainNumber		3.1.1751.2.18.5.9.1.1
The bridge number of the bridge which this interface is a part of. If the interface is currently not associated with any bridge this will be set to none.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bridgeDomainAdminStatus		3.1.1751.2.18.5.9.1.2
The administrative action: 'outOfService' take the interface out of service 'inService' take the interface in service
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

bridgeDomainOperStatus		3.1.1751.2.18.5.9.1.3
The operational status of the interface: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

bridgeDomainPriority		3.1.1751.2.18.5.9.1.4
The value of the writeable portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

bridgeDomainTimeSinceTopologyChange		3.1.1751.2.18.5.9.1.5
The time (in hundredths of a second) since the last time a topology change was detedted by the bridge entity.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

bridgeDomainDesignatedRoot		3.1.1751.2.18.5.9.1.6
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(6)

bridgeDomainRootCost		3.1.1751.2.18.5.9.1.7
The cost of the path to the root as seen from this bridge.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeDomainRootPort		3.1.1751.2.18.5.9.1.8
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeDomainMaxMessageAge		3.1.1751.2.18.5.9.1.9
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeDomainHelloTime		3.1.1751.2.18.5.9.1.10
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeDomainHoldTime		3.1.1751.2.18.5.9.1.11
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeDomainForwardDelay		3.1.1751.2.18.5.9.1.12
This time value, measured in units of hundredths of a second, controls how fast a port changes its state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to bridgeDomainBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeDomainMaxBridgeAge		3.1.1751.2.18.5.9.1.13
The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of bridgeDomainBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	6..40

bridgeDomainBridgeHelloTime		3.1.1751.2.18.5.9.1.14
The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

bridgeDomainBridgeForwardDelay		3.1.1751.2.18.5.9.1.15
The value that all bridges user for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of bridgeDomainMaxBridgeAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	4..30

bridgeDomainAgingTime		3.1.1751.2.18.5.9.1.16
The timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..1000000

bridgeDomainSpanningTree		3.1.1751.2.18.5.9.1.17
Allows the bridge to be configured to run without the spanning tree algorithm.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

bridgeDomainTopologyChanges		3.1.1751.2.18.5.9.1.18
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeDomainLearnedEntryDiscards		3.1.1751.2.18.5.9.1.19
The total number of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them in the Forwarding Database. If this counter is increasing, it indicates that the Forwarding Database is regularly becoming full (a condition which has unpleasant performance effects on the subnetwork). If this counter has a significant value but is not presently increasing, it indicates that the problem has been occurring but is not persistent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeDomainTimer		3.1.1751.2.18.5.9.1.20
Number of seconds elapsed since the last reset of bridge group statistics
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeDomainDefaultGateway		3.1.1751.2.18.5.9.1.21
The default gateway for this bridge domain. This is now an obsolete entry
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

bridgeDomainPortStatusBitmap		3.1.1751.2.18.5.9.1.22
A bit map describing which ports in a bridge group are up or down
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(30)

routerConfigTable		3.1.1751.2.18.5.10
Table which hold Config Entries for all routers (VPNs)
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RouterConfigEntry

routerConfigEntry		3.1.1751.2.18.5.10.1
config data for a router (VPN)
Status: current	Access: not-accessible
OBJECT-TYPE
	RouterConfigEntry

routerIfIndex		3.1.1751.2.18.5.10.1.1
A scalar number which identifies an IP interface within a given router (VPN)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

routerAdminStatus		3.1.1751.2.18.5.10.1.2
The administrative action: 'outOfService' take the interface out of service 'inService' take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

routerOperStatus		3.1.1751.2.18.5.10.1.3
The operational status of the interface: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

routerIpAddress		3.1.1751.2.18.5.10.1.4
router ATM IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

routerIpNetworkMask		3.1.1751.2.18.5.10.1.5
An IP network mask for an IP interface within a given router (VPN)
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

routerNumber		3.1.1751.2.18.5.10.1.6
A scalar number which identifies a given router (VPN)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..999

routerEthernetIpAddress		3.1.1751.2.18.5.10.1.7
router Ethernet IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

isdnConfig		3.1.1751.2.18.5.11
OBJECT IDENTIFIER

isdnIntfConfigTable		3.1.1751.2.18.5.11.1
Table of ISDN interface configuration attriburtes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IsdnIntfConfigEntry

isdnIntfConfigEntry		3.1.1751.2.18.5.11.1.1
Row definition for ISDN interface configuration table
Status: current	Access: not-accessible
OBJECT-TYPE
	IsdnIntfConfigEntry

isdnIntfId		3.1.1751.2.18.5.11.1.1.1
Interface ID (SSPPCCC)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

isdnIntfDChanId		3.1.1751.2.18.5.11.1.1.2
D-Channel Number - if the Dchannel no. is 0 no LAPD will run on this PRI-ISDN interface
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..24

isdnIntfAdminStatus		3.1.1751.2.18.5.11.1.1.3
ISDN interface admin status
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

isdnIntfOperStatus		3.1.1751.2.18.5.11.1.1.4
ISDN interface operational status
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

isdnIntfSwitchType		3.1.1751.2.18.5.11.1.1.5
ISDN interface Switch Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pri-ni2(1), pri-net5(2), pri-1tr6(3), pri-4ess(4), pri-5ess(5), pri-dass2(6), pri-dms100(7), pri-kdd(8), pri-ntt(9), pri-net5sw(10), pri-ts014(11), pri-vn(12)

isdnL2ConfigTable		3.1.1751.2.18.5.11.2
Table of Layer 2 (LAPD) attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IsdnL2ConfigEntry

isdnL2ConfigEntry		3.1.1751.2.18.5.11.2.1
Row definition for ISDN LAPD parameters
Status: current	Access: not-accessible
OBJECT-TYPE
	IsdnL2ConfigEntry

isdnL2IntfId		3.1.1751.2.18.5.11.2.1.1
Interface index (SSPPCCC)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

isdnT200		3.1.1751.2.18.5.11.2.1.2
value of L2 T200 timer in 1/10 seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

isdnT203		3.1.1751.2.18.5.11.2.1.3
value of L2 T203 timer in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..60

isdnN200		3.1.1751.2.18.5.11.2.1.4
Maximum number of retransmissions before the LAPD Link is declared as down
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..5

isdnN201		3.1.1751.2.18.5.11.2.1.5
Maximum number of octets in an information field - Maximum value of this parameter will be 300 bytes.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..300

isdnK		3.1.1751.2.18.5.11.2.1.6
Maximum number of outstanding I frames - L2 - window size.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..127

isdnL2OperStatus		3.1.1751.2.18.5.11.2.1.7
ISDN Layer 2 operational status - not-initiated means that first SETUP message has not been transmitted and L2 estalishment procedure has not been initiated yet
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	not-initiated(1), up(2), down(3)

isdnL2CurrentState		3.1.1751.2.18.5.11.2.1.8
ISDN Layer 2 protocol's current state
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	tei-unassigned(1), tei-assigned(4), awaiting-establishment(5), awaiting-release(6), multiple-frame-established(7), timer-recovery(8)

isdnBChanConfigTable		3.1.1751.2.18.5.11.3
Table of ISDN B Channel configuration attriburtes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IsdnBChanConfigEntry

isdnBChanConfigEntry		3.1.1751.2.18.5.11.3.1
Row definition for ISDN B Channel configuration table
Status: current	Access: not-accessible
OBJECT-TYPE
	IsdnBChanConfigEntry

isdnBChanId		3.1.1751.2.18.5.11.3.1.1
B Chan ID (SSPPCCC)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

isdnBChanAdminStatus		3.1.1751.2.18.5.11.3.1.2
ISDN B Chan admin status
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

isdnBChanOperStatus		3.1.1751.2.18.5.11.3.1.3
ISDN B Chan operational status
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmDbCirEmConfigTable		3.1.1751.2.18.5.12
Table for ATM DBCES Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmDbCirEmConfigEntry

atmDbCirEmConfigEntry		3.1.1751.2.18.5.12.1
Row definition for ATM Dynamic Bandwidth Circuit Emulation interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmDbCirEmConfigEntry

atmDbCirEmIfIndex		3.1.1751.2.18.5.12.1.1
Interface index (slot/port/channel) SSPPCCC.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmDbCirEmAdminStatus		3.1.1751.2.18.5.12.1.2
The administrative action: 'outOfService' take the interface out of service 'inService' take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

atmDbCirEmOperStatus		3.1.1751.2.18.5.12.1.3
The operational status of the interface: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmDbCirEmIdlePattern		3.1.1751.2.18.5.12.1.7
Idle pattern for idle data.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmDbCirEmServiceType		3.1.1751.2.18.5.12.1.8
Service type to be used. Affects the ABCD Signaling.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	plar(1), fxo-loopstart(2), fxs-loopstart(3), fxo-groundstart(4), fxs-groundstart(5)

atmDbCirEmDbcesType		3.1.1751.2.18.5.12.1.9
The type of dbces used. yurie: Yurie proprietary specific.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	lucent(1)

atmDbCirEmIntegrationTime		3.1.1751.2.18.5.12.1.10
This specifies the time to wait after receiving idle pattern to change state. The unit is in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

lmiDlciConfigTable		3.1.1751.2.18.5.13
Table for Lmi DLCI Interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LmiDlciConfigEntry

lmiDlciConfigEntry		3.1.1751.2.18.5.13.1
Row definition for Lmi DLCI Interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	LmiDlciConfigEntry

lmiDlciIfIndex		3.1.1751.2.18.5.13.1.1
Interface index (slot/port/channel) SSPPCCC.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

lmiDlci		3.1.1751.2.18.5.13.1.2
dlci.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

lmiDlciOperStatus		3.1.1751.2.18.5.13.1.3
The operational status of the lmi protocol: 'outOfService' protocol is out of service 'inService' protocol is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

lmiDlciStatusTime		3.1.1751.2.18.5.13.1.4
Time since last status transition occurred.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dsp2ConfigTable		3.1.1751.2.18.5.14
Table for Dsp2 Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsp2ConfigEntry

dsp2ConfigEntry		3.1.1751.2.18.5.14.1
Row definition for Dsp2 interface
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsp2ConfigEntry

dsp2IfIndex		3.1.1751.2.18.5.14.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

dsp2AdminStatus		3.1.1751.2.18.5.14.1.2
The administrative action: 'outOfService' take the interface out of service 'inService' take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

dsp2OperStatus		3.1.1751.2.18.5.14.1.3
The operational status of the interface: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

dsp2LoadCount		3.1.1751.2.18.5.14.1.4
Gives the number of calls going through that dsp. This will be of use in case of deletion of dsp interface. When no calls are going through the dsp this value will be 0
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dsp2AalMode		3.1.1751.2.18.5.14.1.5
aal2-non-multiplexed : Does not support multiplexing of multiple channels with one trunk aal2-standard: Support Standard Aal2 Multiplexing aal1:Support Aal1 mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal2-non-multiplexed(1), aal2-standard(2), aal1(3)

atmImaConfigTable		3.1.1751.2.18.5.15
Inverse Multiplexing interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmImaConfigEntry

atmImaConfigEntry		3.1.1751.2.18.5.15.1
Row definition for Inverse Multiplexing attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmImaConfigEntry

atmImaIntfIndex		3.1.1751.2.18.5.15.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

atmImaNeTxState		3.1.1751.2.18.5.15.1.2
The near-end transmit state. notInGroup -- Interface is not assigned to group unusableNoReason -- Doesn't work; Don't know why. unusableFailed -- Check the Defect value usable -- Interface is ready to go. active -- Interface is in use.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notInGroup(1), unusableNoReason(2), unusableFault(3), unusableMisconnected(4), unusableInhibited(5), unusableFailed(6), usable(7), active(8)

atmImaNeRxState		3.1.1751.2.18.5.15.1.3
The near-end receive state. notInGroup -- Interface is not assigned to group unusableNoReason -- Doesn't work; Don't know why. unusableFailed -- Check the Defect value usable -- Interface is ready to go. active -- Interface is in use.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notInGroup(1), unusableNoReason(2), unusableFault(3), unusableMisconnected(4), unusableInhibited(5), unusableFailed(6), usable(7), active(8)

atmImaFeTxState		3.1.1751.2.18.5.15.1.4
The far-end transmit state. notInGroup -- Interface is not assigned to group unusableNoReason -- Doesn't work; Don't know why. unusableFailed -- Check the Defect value usable -- Interface is ready to go. active -- Interface is in use.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notInGroup(1), unusableNoReason(2), unusableFault(3), unusableMisconnected(4), unusableInhibited(5), unusableFailed(6), usable(7), active(8)

atmImaFeRxState		3.1.1751.2.18.5.15.1.5
The far-end receive state. notInGroup -- Interface is not assigned to group unusableNoReason -- Doesn't work; Don't know why. unusableFailed -- Check the Defect value usable -- Interface is ready to go. active -- Interface is in use.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notInGroup(1), unusableNoReason(2), unusableFault(3), unusableMisconnected(4), unusableInhibited(5), unusableFailed(6), usable(7), active(8)

atmImaNeRxDefect		3.1.1751.2.18.5.15.1.6
The near-end receive defect. noDefect -- No link defect exists linkFailure -- Physical failure/ Loss of signal lifDefect -- Persistence of LIF defect at near-end (Loss of IMA Frame) lodsDefect -- Persistence of LODS defect at near-end (Link Out of Delay Synchronization)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noDefect(1), linkFailure(2), lif(3), lods(4)

atmImaFeRxDefect		3.1.1751.2.18.5.15.1.7
The far-end receive defect. noDefect -- No link defect exists linkFailure -- Physical failure/ Loss of signal lifDefect -- Persistence of LIF defect at near-end (Loss of IMA Frame) lodsDefect -- Persistence of LODS defect at near-end (Link Out of Delay Synchronization)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noDefect(1), linkFailure(2), lif(3), lods(4)

atmImaAdminStatus		3.1.1751.2.18.5.15.1.8
The administrative action: 'outOfService' take the interface out of service 'inService' take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

atmImaOperStatus		3.1.1751.2.18.5.15.1.9
The operational status of the interface: 'outOfService' interface is out of service 'inService' interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmPnniConfigTable		3.1.1751.2.18.5.16
Table of atm PNNI Configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmPnniConfigEntry

atmPnniConfigEntry		3.1.1751.2.18.5.16.1
Row definition of PNNI Configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmPnniConfigEntry

atmPnniIfIndex		3.1.1751.2.18.5.16.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmPnniSvcMinVpi		3.1.1751.2.18.5.16.1.2
The lower bound of the VPI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

atmPnniSvcMaxVpi		3.1.1751.2.18.5.16.1.3
The upper bound of the VPI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

atmPnniSvcMinVci		3.1.1751.2.18.5.16.1.4
The lower bound of the VCI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmPnniSvcMaxVci		3.1.1751.2.18.5.16.1.5
The upper bound of the VCI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmPnniAdminStatus		3.1.1751.2.18.5.16.1.6
The administrative action: 'outOfService' means take the PNNI out of service 'inService' means take the PNNI in service 'delete' remove/deconfigure the PNNI.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

atmPnniOperStatus		3.1.1751.2.18.5.16.1.7
The operational status of the PNNI: 'outOfService' means the PNNI is out of service 'inService' means the PNNI is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmPnniT303		3.1.1751.2.18.5.16.1.8
Timer T303 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniT308		3.1.1751.2.18.5.16.1.9
Timer T308 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniT309		3.1.1751.2.18.5.16.1.10
Timer T309 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniT310		3.1.1751.2.18.5.16.1.11
Timer T310 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniT313		3.1.1751.2.18.5.16.1.12
Timer T313 value - User side only - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniT316		3.1.1751.2.18.5.16.1.13
Timer T316 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniT317		3.1.1751.2.18.5.16.1.14
Timer T317 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniT322		3.1.1751.2.18.5.16.1.15
Timer T322 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniT397		3.1.1751.2.18.5.16.1.16
Timer T397 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniT398		3.1.1751.2.18.5.16.1.17
Timer T398 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniT399		3.1.1751.2.18.5.16.1.18
Timer T399 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniCbrServCatSupp		3.1.1751.2.18.5.16.1.19
If CBR category is supported
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniCbrGcacClpEqualZero		3.1.1751.2.18.5.16.1.20
If the advertised GCAC parameters apply for CLP=0 or CLP=0+1 traffic
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniCbrMaxCellRate		3.1.1751.2.18.5.16.1.21
CBR category Maximum Cell Rate
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniCbrAvailCellRate		3.1.1751.2.18.5.16.1.22
CBR category Available Cell Rate
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniCbrCellXerDelay		3.1.1751.2.18.5.16.1.23
CBR category Cell Transfer Delay
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniCbrCellLossRatioZero		3.1.1751.2.18.5.16.1.24
CBR category Cell Loss Ratio for CLP=0 traffic
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniCbrCellLossRatioZeroPlusOne		3.1.1751.2.18.5.16.1.25
CBR category Cell Loss Ratio for CLP=0+1 traffic
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniCbrCellDelayVar		3.1.1751.2.18.5.16.1.26
CBR category Cell Delay Variation
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniRtVbrServCatSupp		3.1.1751.2.18.5.16.1.27
If RT VBR category is supported
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniRtVbrGcacClpEqualZero		3.1.1751.2.18.5.16.1.28
If the advertised GCAC parameters apply for CLP=0 or CLP=0+1 traffic
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniRtVbrMaxCellRate		3.1.1751.2.18.5.16.1.29
RT VBR category Maximum Cell Rate
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniRtVbrAvailCellRate		3.1.1751.2.18.5.16.1.30
RT VBR category Available Cell Rate
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniRtVbrCellXerDelay		3.1.1751.2.18.5.16.1.31
RT VBR category Cell Transfer Delay
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniRtVbrCellLossRatioZero		3.1.1751.2.18.5.16.1.32
RT VBR category Cell Loss Ratio for CLP=0 traffic
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniRtVbrCellLossRatioZeroPlusOne		3.1.1751.2.18.5.16.1.33
RT VBR category Cell Loss Ratio for CLP=0+1 traffic
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniRtVbrCellDelayVar		3.1.1751.2.18.5.16.1.34
RT VBR category Cell Delay Variation
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniRtVbrGcacPresent		3.1.1751.2.18.5.16.1.35
If RT VBR category GCAC Parameters present
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniRtVbrCellRateMargin		3.1.1751.2.18.5.16.1.36
RT VBR category Cell Rate Margin
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmPnniRtVbrVarianceFactor		3.1.1751.2.18.5.16.1.37
RT VBR category Variance Factor
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmPnniNrtVbrServCatSupp		3.1.1751.2.18.5.16.1.38
If NRT VBR category is supported
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniNrtVbrGcacClpEqualZero		3.1.1751.2.18.5.16.1.39
If the advertised GCAC parameters apply for CLP=0 or CLP=0+1 traffic
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniNrtVbrMaxCellRate		3.1.1751.2.18.5.16.1.40
NRT VBR category Maximum Cell Rate
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniNrtVbrAvailCellRate		3.1.1751.2.18.5.16.1.41
NRT VBR category Available Cell Rate
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniNrtVbrCellXerDelay		3.1.1751.2.18.5.16.1.42
NRT VBR category Cell Transfer Delay
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniNrtVbrCellLossRatioZero		3.1.1751.2.18.5.16.1.43
NRT VBR category Cell Loss Ratio for CLP=0 traffic
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniNrtVbrCellLossRatioZeroPlusOne		3.1.1751.2.18.5.16.1.44
NRT VBR category Cell Loss Ratio for CLP=0+1 traffic
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniNrtVbrGcacPresent		3.1.1751.2.18.5.16.1.45
If NRT VBR category GCAC Parameters present
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniNrtVbrCellRateMargin		3.1.1751.2.18.5.16.1.46
NRT VBR category Cell Rate Margin
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmPnniNrtVbrVarianceFactor		3.1.1751.2.18.5.16.1.47
NRT VBR category Variance Factor
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmPnniAbrServCatSupp		3.1.1751.2.18.5.16.1.48
If ABR category is supported
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniAbrMaxCellRate		3.1.1751.2.18.5.16.1.49
ABR category Maximum Cell Rate
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniAbrAvailCellRate		3.1.1751.2.18.5.16.1.50
ABR category Available Cell Rate
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniUbrServCatSupp		3.1.1751.2.18.5.16.1.51
UBR category Cell Transfer Delay
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniUbrMaxCellRate		3.1.1751.2.18.5.16.1.52
NRT VBR category Cell Loss Ratio for CLP=0 traffic
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniOverSubscription		3.1.1751.2.18.5.16.1.53
Over subscription factor for PNNI Intf.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

atmPnniSgnlEnabled		3.1.1751.2.18.5.16.1.54
Indicates if atm signaling is enabled or disabled for this PNNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniVpiSig		3.1.1751.2.18.5.16.1.55
VPI value for the signalling channel for the PNNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

atmPnniVciSig		3.1.1751.2.18.5.16.1.56
VCI value for the signalling channel for the PNNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..31

atmPnniAvailBwIgr		3.1.1751.2.18.5.16.1.57
The Avail Bandwidth for that interface in cells per sec. Bandwidth for UBR conns will not be accounted for.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPnniAvailBwEgr		3.1.1751.2.18.5.16.1.58
The Avail Bandwidth for that interface in cells per sec. Bandwidth for UBR conns will not be accounted for.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPnniUPCSupp		3.1.1751.2.18.5.16.1.59
upc supp off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmPnniUbrLoadBalSupp		3.1.1751.2.18.5.16.1.60
load balancing supp for ubr conns off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmPnniSscopRxWndSz		3.1.1751.2.18.5.16.1.61
The receive window size for the SSCOP layer
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	8..256

atmPnniRemoteSvcMinVpi		3.1.1751.2.18.5.16.1.62
The lower bound of the actual VPI for SVC connections.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

atmPnniRemoteSvcMaxVpi		3.1.1751.2.18.5.16.1.63
The Upper bound of the actual VPI for SVC connections.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

atmPnniRemoteSvcMinVci		3.1.1751.2.18.5.16.1.64
The lower bound of the actual VCI for SVC connections.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	32..65535

atmPnniRemoteSvcMaxVci		3.1.1751.2.18.5.16.1.65
The Upper bound of the actual VCI for SVC connections.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	32..65535

atmPnniVpiIlmi		3.1.1751.2.18.5.16.1.66
VPI value for the ilmi channel for the PNNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmPnniVciIlmi		3.1.1751.2.18.5.16.1.67
VCI value for the ilmi channel for the PNNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..31

atmPnniIlmiProtocolStatus		3.1.1751.2.18.5.16.1.68
The administrative status: 'enabled' - ILMI protocol enabled on PNNI 'disabled' - ILMI protocol disabled on PNNI .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniIlmiOperStatus		3.1.1751.2.18.5.16.1.69
The operational status: 'outOfService' - ILMI connectivity is down 'inService' - ILMI connectivity is up.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmPnniIlmiConfigProc		3.1.1751.2.18.5.16.1.70
ILMI Configuration Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniIlmiConnectProc		3.1.1751.2.18.5.16.1.71
ILMI Connectivity Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniIlmiAttachPtProc		3.1.1751.2.18.5.16.1.72
ILMI Attachment Point Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniIlmiSecureLinkProc		3.1.1751.2.18.5.16.1.73
ILMI Secure Link Procedure status. Can be enabled only if Attachment Point Procedure is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniIlmiAddrRegProc		3.1.1751.2.18.5.16.1.74
ILMI Address Registration Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atmPnniIlmiTimerS		3.1.1751.2.18.5.16.1.75
Timer S (secs). Used to poll peer when link is down.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniIlmiTimerT		3.1.1751.2.18.5.16.1.76
Timer T (secs). Used to poll peer when link is up.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniIlmiRetryK		3.1.1751.2.18.5.16.1.77
Retry K - number of timeouts of before link is declared down.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPnniConnTrafficShapingFlag		3.1.1751.2.18.5.16.1.78
Traffic Shaping for Conn was enabled primarily because the core would lose cells since we were non-conformant cells. Therefore the hardware added traffic shaping per connection. But condition is VI should not be enabled if this feature is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmVnnConfigTable		3.1.1751.2.18.5.17
Table of atm user to network interface (UNI)
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVnnConfigEntry

atmVnnConfigEntry		3.1.1751.2.18.5.17.1
Row definition of atm UNI
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVnnConfigEntry

atmVnnIfIndex		3.1.1751.2.18.5.17.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmVnnAddrType		3.1.1751.2.18.5.17.1.2
atm address type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nsap(1), e164(2), private(3)

atmVnnSvcMinVpi		3.1.1751.2.18.5.17.1.3
The lower bound of the VPI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmVnnSvcMaxVpi		3.1.1751.2.18.5.17.1.4
The upper bound of the VPI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmVnnSvcMinVci		3.1.1751.2.18.5.17.1.5
The lower bound of the VCI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmVnnSvcMaxVci		3.1.1751.2.18.5.17.1.6
The upper bound of the VCI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmVnnAdminStatus		3.1.1751.2.18.5.17.1.7
The administrative action: 'outOfService' means take the UNI out of service 'inService' means take the UNI in service 'delete' remove/deconfigure the UNI.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

atmVnnOperStatus		3.1.1751.2.18.5.17.1.8
The operational status of the UNI: 'outOfService' means the UNI is out of service 'inService' means the UNI is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmVnnOverSubscription		3.1.1751.2.18.5.17.1.9
Over subscription factor
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

atmVnnNwPrefix1		3.1.1751.2.18.5.17.1.10
ATM Network Prefix 1
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(13)

atmVnnT303		3.1.1751.2.18.5.17.1.11
Timer T303 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnT308		3.1.1751.2.18.5.17.1.12
Timer T308 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnT309		3.1.1751.2.18.5.17.1.13
Timer T309 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnT310		3.1.1751.2.18.5.17.1.14
Timer T310 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnT313		3.1.1751.2.18.5.17.1.15
Timer T313 value - User side only - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnT316		3.1.1751.2.18.5.17.1.16
Timer T316 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnT317		3.1.1751.2.18.5.17.1.17
Timer T317 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnT322		3.1.1751.2.18.5.17.1.18
Timer T322 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnT398		3.1.1751.2.18.5.17.1.19
Timer T398 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnT399		3.1.1751.2.18.5.17.1.20
Timer T399 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnMyNeighborIpAddress		3.1.1751.2.18.5.17.1.21
The IP address of the neighbor system connected to the far end of this interface, to which a Network Management Station can send SNMP messages, as IP datagrams sent to UDP port 161, in order to access network management information concerning the operation of that system. Note that the value of this object can currently only be obtained by manual configuration.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

atmVnnMyNeighborIfName		3.1.1751.2.18.5.17.1.22
The textual name of the interface on the neighbor system on the far end of this interface, and to which this interface connects. If the neighbor system is manageable through SNMP and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. If this interface does not have a textual name, the value of this object is a zero length string. Note that the value of this object can currently only be obtained by manual configuration.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

atmVnnVpiSig		3.1.1751.2.18.5.17.1.23
VPI value for the signalling channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmVnnVciSig		3.1.1751.2.18.5.17.1.24
VCI value for the signalling channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..31

atmVnnVpiIlmi		3.1.1751.2.18.5.17.1.25
VPI value for the ilmi channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmVnnVciIlmi		3.1.1751.2.18.5.17.1.26
VCI value for the ilmi channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..31

atmVnnAtmSignalingStatus		3.1.1751.2.18.5.17.1.27
Indicates if atm signaling is enabled or disabled for this interface. Consistent with other AC interfaces
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1)

atmVnnMyIfName		3.1.1751.2.18.5.17.1.28
A textual name of this interface. If this system is manageable manageable through SNMP and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. This interface must be uniquely named on this system to distinguish parallel links with a neighboring system. If this interface does not have a textual name, the value of this object is a zero length string.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

atmVnnIlmiProtocolStatus		3.1.1751.2.18.5.17.1.29
The administrative status: 'enabled' - ILMI protocol enabled on UNI.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1)

atmVnnIlmiOperStatus		3.1.1751.2.18.5.17.1.30
The operational status: 'outOfService' - ILMI connectivity is down 'inService' - ILMI connectivity is up.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

atmVnnIlmiConfigProc		3.1.1751.2.18.5.17.1.31
ILMI Configuration Procedure status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(2)

atmVnnIlmiConnectProc		3.1.1751.2.18.5.17.1.32
ILMI Connectivity Procedure status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1)

atmVnnIlmiAttachPtProc		3.1.1751.2.18.5.17.1.33
ILMI Attachment Point Procedure status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(2)

atmVnnIlmiSecureLinkProc		3.1.1751.2.18.5.17.1.34
ILMI Secure Link Procedure status. Can be enabled only if Attachment Point Procedure is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(2)

atmVnnIlmiAddrRegProc		3.1.1751.2.18.5.17.1.35
ILMI Address Registration Procedure status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1)

atmVnnIlmiTimerS		3.1.1751.2.18.5.17.1.36
Timer S (secs). Used to poll peer when link is down.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnIlmiTimerT		3.1.1751.2.18.5.17.1.37
Timer T (secs). Used to poll peer when link is up.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnIlmiRetryK		3.1.1751.2.18.5.17.1.38
Retry K - number of timeouts before link is declared down.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmVnnAvailBwIgr		3.1.1751.2.18.5.17.1.39
The Avail Bandwidth for that interface in cells per sec. Bandwidth for UBR conns will not be accounted for.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVnnAvailBwEgr		3.1.1751.2.18.5.17.1.40
The Avail Bandwidth for that interface in cells per sec. Bandwidth for UBR conns will not be accounted for.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVnnUPCSupp		3.1.1751.2.18.5.17.1.41
upc supp off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmVnnUbrLoadBalSupp		3.1.1751.2.18.5.17.1.42
load balancing supp for ubr conns off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmVnnSscopRxWndSz		3.1.1751.2.18.5.17.1.43
The receive window size for the SSCOP layer
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	8..256

virtualIntfConfigTable		3.1.1751.2.18.5.18
Table of Virtual Interfaces Configurations
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VirtualIntfConfigEntry

virtualIntfConfigEntry		3.1.1751.2.18.5.18.1
Index is the Interface and the Virutal Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	VirtualIntfConfigEntry

virtualIntfConfigIf		3.1.1751.2.18.5.18.1.1
Interface index for side A of an ATM-to-ATM PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

virtualIntfConfigVi		3.1.1751.2.18.5.18.1.2
VI value. Def Val is 1 because 0 cannot be configured
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..1024

virtualIntfConfigCellRate		3.1.1751.2.18.5.18.1.3
Bandwidth assigned for the VI. The unit is cells per sec. Total Bandwidth of all VI's cannot exceed bandwidth of the main interface. CAC will be supported per VI.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualIntfConfigOverSubs		3.1.1751.2.18.5.18.1.4
Over Subscription rate for VI
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualIntfConfigRowStatus		3.1.1751.2.18.5.18.1.5
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

virtualIntfConfigUPCSupp		3.1.1751.2.18.5.18.1.6
virtual interface upc supp off/on If this is changed then all the connections on this interface will be replayed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

virtualIntfAvailBwEgr		3.1.1751.2.18.5.18.1.7
Avail Bw for that VI in cells per sec in the Egress Direction or the direction away from back plane.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

virtualUNIConfigTable		3.1.1751.2.18.5.19
Table of Virtual UNI Interfaces Configurations
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VirtualUNIConfigEntry

virtualUNIConfigEntry		3.1.1751.2.18.5.19.1
Index is the Interface and the Virutal UNI Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	VirtualUNIConfigEntry

virtualUNIIfIndex		3.1.1751.2.18.5.19.1.1
This is the first index to the Virtual UNI Interface table. Interface index will be of the form SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

virtualUNIVUNIId		3.1.1751.2.18.5.19.1.2
Virtual UNI number, second index to access the virtual UNI interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..255

virtualUNIVISupport		3.1.1751.2.18.5.19.1.3
Virtual Interface (Traffic Shaping) is enabled or disabled on this VUNI. A Virtual Interface should already be configured befaore the traffic shaping can be enabled on this VUNI. If VISupport is disabled then all the connections on the VUNI can only be configured as UBR connections if this VUNI interface is on a VI enabled physical interface
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

virtualUNIMinVpi		3.1.1751.2.18.5.19.1.4
Lower value of the VPI range for this VUNI
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

virtualUNIMaxVpi		3.1.1751.2.18.5.19.1.5
Upper value of the VPI range for this VUNI
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

virtualUNIConfigRowStatus		3.1.1751.2.18.5.19.1.6
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

virtualUNIAddrType		3.1.1751.2.18.5.19.1.7
atm address type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nsap(1), e164(2), private(3)

virtualUNISvcMinVpi		3.1.1751.2.18.5.19.1.8
The lower bound of the VPI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

virtualUNISvcMaxVpi		3.1.1751.2.18.5.19.1.9
The upper bound of the VPI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

virtualUNISvcMinVci		3.1.1751.2.18.5.19.1.10
The lower bound of the VCI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

virtualUNISvcMaxVci		3.1.1751.2.18.5.19.1.11
The upper bound of the VCI for SVC connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

virtualUNIAdminStatus		3.1.1751.2.18.5.19.1.12
The administrative action: 'outOfService' means take the VUNI out of service 'inService' means take the VUNI in service
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

virtualUNIOperStatus		3.1.1751.2.18.5.19.1.13
The operational status of the VUNI: 'outOfService' means the VUNI is out of service 'inService' means the VUNI is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

virtualUNINwPrefix1		3.1.1751.2.18.5.19.1.14
ATM Network Prefix 1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(13)

virtualUNIT303		3.1.1751.2.18.5.19.1.15
Timer T303 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIT308		3.1.1751.2.18.5.19.1.16
Timer T308 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIT309		3.1.1751.2.18.5.19.1.17
Timer T309 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIT310		3.1.1751.2.18.5.19.1.18
Timer T310 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIT313		3.1.1751.2.18.5.19.1.19
Timer T313 value - User side only - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIT316		3.1.1751.2.18.5.19.1.20
Timer T316 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIT317		3.1.1751.2.18.5.19.1.21
Timer T317 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIT322		3.1.1751.2.18.5.19.1.22
Timer T322 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIT398		3.1.1751.2.18.5.19.1.23
Timer T398 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIT399		3.1.1751.2.18.5.19.1.24
Timer T399 value - seconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIMyNeighborIpAddress		3.1.1751.2.18.5.19.1.25
The IP address of the neighbor system connected to the far end of this interface, to which a Network Management Station can send SNMP messages, as IP datagrams sent to UDP port 161, in order to access network management information concerning the operation of that system. Note that the value of this object can currently only be obtained by manual configuration.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

virtualUNIMyNeighborIfName		3.1.1751.2.18.5.19.1.27
The textual name of the interface on the neighbor system on the far end of this interface, and to which this interface connects. If the neighbor system is manageable through SNMP and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. If this interface does not have a textual name, the value of this object is a zero length string. Note that the value of this object can currently only be obtained by manual configuration.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

virtualUNIVpiSig		3.1.1751.2.18.5.19.1.28
VPI value for the signalling channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

virtualUNIVciSig		3.1.1751.2.18.5.19.1.29
VCI value for the signalling channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..31

virtualUNISignalingAdminStatus		3.1.1751.2.18.5.19.1.30
Indicates if atm signaling is enabled or disabled for this VUNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

virtualUNISignalingOperStatus		3.1.1751.2.18.5.19.1.31
The protocol operational status of the UNI: 'outOfService' means the UNI is out of service 'inService' means the UNI is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inService(1), outOfService(2)

virtualUNIVpiIlmi		3.1.1751.2.18.5.19.1.32
VPI value for the ilmi channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

virtualUNIVciIlmi		3.1.1751.2.18.5.19.1.33
VCI value for the ilmi channel for the UNI interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..31

virtualUNIMyIfName		3.1.1751.2.18.5.19.1.34
A textual name of this interface. If this system is manageable manageable through SNMP and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. This interface must be uniquely named on this system to distinguish parallel links with a neighboring system. If this interface does not have a textual name, the value of this object is a zero length string.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

virtualUNIIlmiProtocolStatus		3.1.1751.2.18.5.19.1.35
The administrative status: 'enabled' - ILMI protocol enabled on UNI 'disabled' - ILMI protocol disabled on UNI.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

virtualUNIIlmiOperStatus		3.1.1751.2.18.5.19.1.36
The operational status: 'outOfService' - ILMI connectivity is down 'inService' - ILMI connectivity is up.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

virtualUNIIlmiConfigProc		3.1.1751.2.18.5.19.1.37
ILMI Configuration Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

virtualUNIIlmiConnectProc		3.1.1751.2.18.5.19.1.38
ILMI Connectivity Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

virtualUNIIlmiAttachPtProc		3.1.1751.2.18.5.19.1.39
ILMI Attachment Point Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

virtualUNIIlmiSecureLinkProc		3.1.1751.2.18.5.19.1.40
ILMI Secure Link Procedure status. Can be enabled only if Attachment Point Procedure is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

virtualUNIIlmiAddrRegProc		3.1.1751.2.18.5.19.1.41
ILMI Address Registration Procedure status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

virtualUNIIlmiTimerS		3.1.1751.2.18.5.19.1.42
Timer S (secs). Used to poll peer when link is down.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIIlmiTimerT		3.1.1751.2.18.5.19.1.43
Timer T (secs). Used to poll peer when link is up.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIIlmiRetryK		3.1.1751.2.18.5.19.1.44
Retry K - number of timeouts before link is declared down.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

virtualUNIIntfType		3.1.1751.2.18.5.19.1.45
atm interface type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	user(1), network(2)

virtualUNIUserAddress		3.1.1751.2.18.5.19.1.46
ATM User Address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(7)

virtualUNIUserAddrOrgScope		3.1.1751.2.18.5.19.1.47
ATM User Address Organizational scope
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	localNetwork(1), localNetworkPlusOne(2), localNetworkPlusTwo(3), siteMinusOne(4), intraSite(5), sitePlusOne(6), organizationMinusOne(7), intraOrganization(8), organizationPlusOne(9), communityMinusOne(10), intraCommunity(11), communityPlusOne(12), regional(13), interRegional(14), global(15)

virtualUNISscopRxWndSz		3.1.1751.2.18.5.19.1.48
The receive window size for the SSCOP layer
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	8..256

casConfig		3.1.1751.2.18.5.20
OBJECT IDENTIFIER

casConfigTable		3.1.1751.2.18.5.20.1
Table for CAS trunk/line configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CasConfigEntry

casConfigEntry		3.1.1751.2.18.5.20.1.1
Row definition for CAS trunk/line configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	CasConfigEntry

casIfIndex		3.1.1751.2.18.5.20.1.1.1
The channel ID (slot/port/channel) in SSPPCCC format associated with the CAS trunk/line.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

casAdminStatus		3.1.1751.2.18.5.20.1.1.2
The administrative action: outOfService-take the CAS trunk/line out of service, inService-take the CAS trunk/line in service, delete-remove/deconfigure the CAS trunk/line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

casOperStatus		3.1.1751.2.18.5.20.1.1.3
The operational status of the CAS trunk/line: outOfService-the CAS trunk/line is out of service, inService-the CAS trunk/line is in service.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

casProtocolType		3.1.1751.2.18.5.20.1.1.4
The type of CAS protocol to be used. The protocol must match the one used on the other end of the trunk/line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	wink-start(1), loop-start-network(2), loop-start-user(3), ground-start-network(4), ground-start-user(5), itu-t-r2(6)

casDirection		3.1.1751.2.18.5.20.1.1.5
The direction of traffic flow on this CAS trunk/line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	both(1), incoming(2), outgoing(3)

casAddressingType		3.1.1751.2.18.5.20.1.1.6
The addressing type used for the CAS trunk/line. dtmf -- dual tone multifrequency r1-mf -- R1 multifrequency, r2-mf -- R2 multifrequency. Type of 're-mf' is valid only when casProtocolType is 'wink start', while 'r2-mf' is valid only when casProtocolType is 'itu-t r2' .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dtmf(1), r1-mf(2), r2-mf(3)

casBitPatternType		3.1.1751.2.18.5.20.1.1.7
The type of bit pattern used for supervisory signaling. The value is AB when SF framing is used, ABCD when ESF framing is used for DS1. In case of E1, the value is always ABCD.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ab(1), abcd(2)

casGroupId		3.1.1751.2.18.5.20.1.1.8
The identifier to associate a group of CAS trunks/lines which have same reachability. When SG is disabled, it must be specified with a non-zero value. When SG is enabled, the value should be set to zero which indicate no routing performed based on the value.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

toneAnnceConfigTable		3.1.1751.2.18.5.21
Table for the Tone Announcement Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ToneAnnceConfigEntry

toneAnnceConfigEntry		3.1.1751.2.18.5.21.1
Row definition for Tone Announcement interface
Status: current	Access: not-accessible
OBJECT-TYPE
	ToneAnnceConfigEntry

toneAnnceIfIndex		3.1.1751.2.18.5.21.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

toneAnnceAdminStatus		3.1.1751.2.18.5.21.1.2
The administrative action: 'outOfService' means take the interface out of service 'inService' means take the interface in service 'delete' remove/deconfigure the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

toneAnnceOperStatus		3.1.1751.2.18.5.21.1.3
The operational status of the interface: 'outOfService' means the interface is out of service 'inService' means the interface is in service
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

gr303IntfConfig		3.1.1751.2.18.5.22
OBJECT IDENTIFIER

gr303IntfConfigTable		3.1.1751.2.18.5.22.1
Table of GR303 interface configuration attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gr303IntfConfigEntry

gr303IntfConfigEntry		3.1.1751.2.18.5.22.1.1
Row definition for GR303 interface configuration table
Status: current	Access: not-accessible
OBJECT-TYPE
	Gr303IntfConfigEntry

gr303IntfId		3.1.1751.2.18.5.22.1.1.1
Interface ID (SSPPCCC)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

gr303TMCChannelId		3.1.1751.2.18.5.22.1.1.2
TMC-Channel Number. If TMC Channel is set to 0 there will be no TMC channel on the corresponding DS1. Generally the TMC channel should be specified on the one of the DS1's in a GR303 interface group and should be on DS0 no. 24
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..24

gr303EOCChannelId		3.1.1751.2.18.5.22.1.1.3
EOC-Channel Number. If EOC Channel is set to 0 there will be no EOC channel on the corresponding DS1. Generally the TMC channel should be specified on the one of the DS1's in a GR303 interface group and should be on DS0 no. 12
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..24

gr303IntfAdminStatus		3.1.1751.2.18.5.22.1.1.4
GR303 interface admin status
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), delete(3)

gr303IntfOperStatus		3.1.1751.2.18.5.22.1.1.5
GR303 interface operational status
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

gr303Ds0ChanConfigTable		3.1.1751.2.18.5.22.2
Table of GR303 DS0 Channel configuration attriburtes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gr303Ds0ChanConfigEntry

gr303Ds0ChanConfigEntry		3.1.1751.2.18.5.22.2.1
Row definition for GR303 DS0 Channel configuration table
Status: current	Access: not-accessible
OBJECT-TYPE
	Gr303Ds0ChanConfigEntry

gr303Ds0ChanId		3.1.1751.2.18.5.22.2.1.1
GR303 DS0 Chan ID (SSPPCCC)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

gr303Ds0ChanAdminStatus		3.1.1751.2.18.5.22.2.1.2
GR303 Ds0 Chan admin status
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

gr303Ds0ChanOperStatus		3.1.1751.2.18.5.22.2.1.3
GR303 Ds0 Chan operational status
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

gr303IgConfig		3.1.1751.2.18.26.1
OBJECT IDENTIFIER

gr303IgConfigTable		3.1.1751.2.18.26.1.1
Table of GR303 group configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gr303IgConfigEntry

gr303IgConfigEntry		3.1.1751.2.18.26.1.1.1
Row definition for GR303 group configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	Gr303IgConfigEntry

gr303IgId		3.1.1751.2.18.26.1.1.1.1
This is used as an index into GR303IG table which recognizes GR303 Interface Group
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..84

gr303IgRowStatus		3.1.1751.2.18.26.1.1.1.2
GR303IG config entry row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

gr303IgAdminStatus		3.1.1751.2.18.26.1.1.1.3
Administrative status of the GR303IG
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	inService(1), outOfService(2)

gr303IgPrimaryTMCChanIntfId		3.1.1751.2.18.26.1.1.1.4
Primary TMC channel Interface Id in SSPPCCC format
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

gr303IgPrimaryEOCChanIntfId		3.1.1751.2.18.26.1.1.1.5
Primary EOC channel Interface Id in SSPPCCC format
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

gr303IgBackupTMCChanIntfId		3.1.1751.2.18.26.1.1.1.6
Backup TMC channel Interface Id in SSPPCCC format
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

gr303IgBackupEOCChanIntfId		3.1.1751.2.18.26.1.1.1.7
Backup EOC channel Interface Id in SSPPCCC format
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

gr303IgPrimaryTMCStatus		3.1.1751.2.18.26.1.1.1.8
Primary TMC channel Status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	standby-OutOfService(1), standby-InService(2), active-OutOfService(3), active-InService(4)

gr303IgPrimaryEOCStatus		3.1.1751.2.18.26.1.1.1.9
Primary EOC channel Status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	standby-OutOfService(1), standby-InService(2), active-OutOfService(3), active-InService(4)

gr303IgBackupTMCStatus		3.1.1751.2.18.26.1.1.1.10
Backup TMC channel Status.Value null(5) Indicates that the Backup TMC has not been configured.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	standby-OutOfService(1), standby-InService(2), active-OutOfService(3), active-InService(4), null(5)

gr303IgBackupEOCStatus		3.1.1751.2.18.26.1.1.1.11
Backup EOC channel Status.Value null(5) Indicates that the Backup EOC has not been configured.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	standby-OutOfService(1), standby-InService(2), active-OutOfService(3), active-InService(4), null(5)

gr303IgTMCProtSwitchProvState		3.1.1751.2.18.26.1.1.1.12
Lock/Unlock the protection switch
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pps-inhibit(1), pps-enable(2)

gr303IgEOCProtSwitchProvState		3.1.1751.2.18.26.1.1.1.13
Lock/Unlock the protection switch
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pps-inhibit(1), pps-enable(2)

gr303IgTMCProtSwitchCommand		3.1.1751.2.18.26.1.1.1.14
User command to do path protection switch
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noAction(1), normalSwitchToBackup(2), normalSwitchToPrimary(3), forcedSwitchToBackup(4), forcedSwitchToPrimary(5)

gr303IgEOCProtSwitchCommand		3.1.1751.2.18.26.1.1.1.15
User command to do path protection switch
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noAction(1), normalSwitchToBackup(2), normalSwitchToPrimary(3), forcedSwitchToBackup(4), forcedSwitchToPrimary(5)

gr303IgLocalDigitalSwitchType		3.1.1751.2.18.26.1.1.1.16
LDS (IDT) type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	lucent-5ess(1), nortel-dms(2)

gr303IgLocalDigitalSwitchVersion		3.1.1751.2.18.26.1.1.1.17
LDS (IDT)Version
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	lucent-5ess-version-1(1), nortel-dms-version-1(2)

gr303IgIntfConfigTable		3.1.1751.2.18.26.1.2
Table of interface attributes in an GR303IG
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gr303IgIntfConfigEntry

gr303IgIntfConfigEntry		3.1.1751.2.18.26.1.2.1
Row definition for GR303 Access Arrangement Interface configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	Gr303IgIntfConfigEntry

gr303IntfIgId		3.1.1751.2.18.26.1.2.1.1
This is used as an index into GR303Ig table which recognizes GR303 Interface Group. This is used as a first index into this interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..84

gr303IgIntfId		3.1.1751.2.18.26.1.2.1.2
This is used as an index into IG interface table which recognizes GR303 Ig interfaces. This is used as a second index into this table
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..28

gr303IgIntfPhysId		3.1.1751.2.18.26.1.2.1.3
Interface's Physical ID (SSPPCCC)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

gr303IgIntfNetId		3.1.1751.2.18.26.1.2.1.4
gr303Ig Interface (DS1) Net Id assigned by the network
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

gr303IgIntfRowStatus		3.1.1751.2.18.26.1.2.1.5
GR303IG interface entry row status - row status can not be made active until all the values are set
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

gr303LapdConfigTable		3.1.1751.2.18.26.1.4
Table of LAPD attributes in an GR303IG
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gr303LapdConfigEntry

gr303LapdConfigEntry		3.1.1751.2.18.26.1.4.1
Row definition for LAPD attributes in a GR303IG
Status: current	Access: not-accessible
OBJECT-TYPE
	Gr303LapdConfigEntry

gr303LapdIgId		3.1.1751.2.18.26.1.4.1.1
GR303IG Number index which recognizes GR303 Interface group
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..84

gr303T200		3.1.1751.2.18.26.1.4.1.2
value of Lapd T200 timer in miliseconds in step size of 50 ms
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	100..350

gr303T203		3.1.1751.2.18.26.1.4.1.3
value of Lapd T203 timer in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..300

gr303N200		3.1.1751.2.18.26.1.4.1.4
Maximum number of retransmissions
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

gr303K		3.1.1751.2.18.26.1.4.1.5
Maximum number of outstanding I frames - Lapd - window size.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..7

gr303TMCConfigTable		3.1.1751.2.18.26.1.5
Table of Layer 3 attributes in an GR303IG
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gr303TMCConfigEntry

gr303TMCConfigEntry		3.1.1751.2.18.26.1.5.1
Row definition for GR303 Access Arrangement Layer3 parameters configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	Gr303TMCConfigEntry

gr303TMCIgId		3.1.1751.2.18.26.1.5.1.1
GR303IG Number index which recognizes GR303 Interface group
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..84

gr303TMCT303		3.1.1751.2.18.26.1.5.1.2
value of TMC T303 timer in miliseconds with a step size of 500 ms
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	700..4700

gr303TMCT396		3.1.1751.2.18.26.1.5.1.3
value of TMC T396 timer in miliseconds with a step size of 1000 ms
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	700..14700

gr303IgStats		3.1.1751.2.18.27.1
OBJECT IDENTIFIER

gr303IgStatsTable		3.1.1751.2.18.27.1.1
Table of GR303 GR303IG based stats attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gr303IgStatsEntry

gr303IgStatsEntry		3.1.1751.2.18.27.1.1.1
Row definition for GR303 GR303IG based stats
Status: current	Access: not-accessible
OBJECT-TYPE
	Gr303IgStatsEntry

gr303IgStatsIgId		3.1.1751.2.18.27.1.1.1.1
This is used as an index into GR303 Ig table which recognizes GR303 Interface Group Interface group
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..84

gr303IgStatsCurrentInCalls		3.1.1751.2.18.27.1.1.1.2
Total number of Currently established incoming calls
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

gr303IgStatsCurrentOutCalls		3.1.1751.2.18.27.1.1.1.3
Total number of Currently established outgoing calls
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

gr303IgStatsOutCallSuccessful		3.1.1751.2.18.27.1.1.1.4
Total number successful outgoing calls
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

gr303IgStatsOutCallFailed		3.1.1751.2.18.27.1.1.1.5
Total number of Failed outgoing calls
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

gr303IgStatsInCallSuccessful		3.1.1751.2.18.27.1.1.1.6
Total number successful incoming calls
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

gr303IgStatsInCallFailed		3.1.1751.2.18.27.1.1.1.7
Total number of Failed incoming calls
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

gr303IgStatsReset		3.1.1751.2.18.27.1.1.1.8
gr303Ig reset statistics button
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

atmPvcVccTable		3.1.1751.2.18.6.1
Table of PVC atm virtual channel connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmPvcVccEntry

atmPvcVccEntry		3.1.1751.2.18.6.1.1
Row definition of atm PVC VCC connections
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmPvcVccEntry

atmPvcVccIfA		3.1.1751.2.18.6.1.1.1
Interface index for side A of an ATM-to-ATM PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmPvcVccVpiA		3.1.1751.2.18.6.1.1.2
VPI value for side A of an ATM-to-ATM PVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmPvcVccVciA		3.1.1751.2.18.6.1.1.3
VCI value for side A of an ATM-to-ATM PVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmPvcVccIfB		3.1.1751.2.18.6.1.1.4
Interface index for side B of an ATM-to-ATM PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmPvcVccVpiB		3.1.1751.2.18.6.1.1.5
VPI value for side B of an ATM-to-ATM PVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmPvcVccVciB		3.1.1751.2.18.6.1.1.6
VCI value for side B of an ATM-to-ATM PVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmPvcVccServiceTypeA2B		3.1.1751.2.18.6.1.1.7
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9), cbr1(10), gfr2(11)

atmPvcVccSarTypeA2B		3.1.1751.2.18.6.1.1.8
SAR type used in atm adaption
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmPvcVccPeakCellRateA2B		3.1.1751.2.18.6.1.1.10
peak cell rate - side A, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVccSusCellRateA2B		3.1.1751.2.18.6.1.1.11
sustained rate - side A, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVccMaxBurstSizeA2B		3.1.1751.2.18.6.1.1.12
maximum burst size - side A, in cells
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVccServiceTypeB2A		3.1.1751.2.18.6.1.1.13
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9), cbr1(10), gfr2(11)

atmPvcVccSarTypeB2A		3.1.1751.2.18.6.1.1.14
sar type used in atm adaption
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmPvcVccPeakCellRateB2A		3.1.1751.2.18.6.1.1.16
peak rate - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVccSusCellRateB2A		3.1.1751.2.18.6.1.1.17
sustained rate - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.1.1.18
maximum burst size - side B, in cells.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVccType		3.1.1751.2.18.6.1.1.20
type of connection
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nonsecured(1), secured(2)

atmPvcVccFlow		3.1.1751.2.18.6.1.1.21
type of flow
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), pointToMultipointA2B(3)

atmPvcVccRowStatus		3.1.1751.2.18.6.1.1.22
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

atmPvcVccFrwdErrCorrectionA2B		3.1.1751.2.18.6.1.1.23
Forward error correction scheme
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4), autoHiQ(5), auto(6), autoLoQ(7)

atmPvcVccFrwdErrCorrectionB2A		3.1.1751.2.18.6.1.1.24
Forward error correction scheme
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4), autoHiQ(5), auto(6), autoLoQ(7)

atmPvcVccConnectionStatus		3.1.1751.2.18.6.1.1.25
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

atmPvcVccOamStatus		3.1.1751.2.18.6.1.1.26
Indicates the OAM monitoring status of side A. The 5 possible states are: Unsupp: No monitoring enabled. End-Pt: A side is only an end point, therefore it will respond to AIS/RDI. Seg-Pt: A side is only a segment point, therefore it will only respond to maintenance OAM cells and not fault cells. End-Seg-Pt: A side is both an end point and a segment point. Intermediate-Pt: It will only generate AIS during local failure. For ATM-to-ATM connections the OAM status will be symmetric on both sides of the connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), seg-Pt(3), end-Seg-Pt(4), intermediate-Pt(5), intra-Segment-Pt(6)

atmPvcVccDualHomed		3.1.1751.2.18.6.1.1.27
Does this PVC need a backup Dual homing PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(1), yes(2)

atmPvcVccViA		3.1.1751.2.18.6.1.1.28
VI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmPvcVccViB		3.1.1751.2.18.6.1.1.29
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmPvcVccCnfrmTypeA2B		3.1.1751.2.18.6.1.1.30
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one_bucket_notag_0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two_bucket_notag_0plus1_0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two_bucket_notag_0plus1_0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two_bucket_tag_0plus1_0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best_effort_tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

atmPvcVccCnfrmTypeB2A		3.1.1751.2.18.6.1.1.31
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one_bucket_notag_0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two_bucket_notag_0plus1_0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two_bucket_notag_0plus1_0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two_bucket_tag_0plus1_0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best_effort_tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

atmPvcVccVUNIA		3.1.1751.2.18.6.1.1.32
VUNI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmPvcVccVUNIB		3.1.1751.2.18.6.1.1.33
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmPvcVccOamStatusB		3.1.1751.2.18.6.1.1.34
Indicates the Oam monitoring status of side B of an internal connection. Refer to ITU I.610 and Bellcore GR1248-CORE for definitions. The 6 possible states are: Unsupp: No OAM cell monitoring or generation enabled. All OAM flows are transparently passed through. End-Pt: Connection endPoint, segment flows are discarded. Seg-Pt: Segment endPoint. End-Seg-Pt: Connection endPoint that is also a segment endPoint. Intermediate-Pt: Connecting point, that is outside any segment. Generates only ete flows. Intra-Segment-Pt: Connecting point with a segment. Generates ete as well as segment flows.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), seg-Pt(3), end-Seg-Pt(4), intermediate-Pt(5), intra-Segment-Pt(6)

atmPvcVccOAMConnEndPtStatusA		3.1.1751.2.18.6.1.1.35
Connection endpoint side A status. Valid only at connection endpoint.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ete-active(1), ete-ais-state(2), ete-rdi-state(3), ete-ais-rdi-state(4)

atmPvcVccOAMConnEndPtStatusB		3.1.1751.2.18.6.1.1.36
Connection endpoint side B status. Valid only at connection endpoint.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ete-active(1), ete-ais-state(2), ete-rdi-state(3), ete-ais-rdi-state(4)

atmPvcVccOAMConnSegEndPtStatusA		3.1.1751.2.18.6.1.1.37
Segment endpoint side A status. Valid only at segment endpoints.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	seg-active(1), seg-ais-state(2), seg-rdi-state(3), seg-ais-rdi-state(4)

atmPvcVccOAMConnSegEndPtStatusB		3.1.1751.2.18.6.1.1.38
Segment endpoint side B status. Valid only at segment endpoints.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	seg-active(1), seg-ais-state(2), seg-rdi-state(3), seg-ais-rdi-state(4)

atmPvcVccMfsA2B		3.1.1751.2.18.6.1.1.39
Maximum Frame Size for GFR traffic for A2B dir
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

atmPvcVccMfsB2A		3.1.1751.2.18.6.1.1.40
Maximum Frame Size for GFR traffic for B2A dir
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

atmPvcVccConnFailureCauseA		3.1.1751.2.18.6.1.1.41
connestion status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

atmPvcVccConnFailureCauseB		3.1.1751.2.18.6.1.1.42
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

atmPvcVccTrafficShapingA2B		3.1.1751.2.18.6.1.1.43
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmPvcVccTrafficShapingB2A		3.1.1751.2.18.6.1.1.44
Traffic Shaping Support in the B2A direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmPvcVpcTable		3.1.1751.2.18.6.2
Table of PVC atm virtual path connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmPvcVpcEntry

atmPvcVpcEntry		3.1.1751.2.18.6.2.1
Row definition of atm connections
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmPvcVpcEntry

atmPvcVpcIfA		3.1.1751.2.18.6.2.1.1
Interface index for side A of an ATM-to-ATM PVC VPC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmPvcVpcVpiA		3.1.1751.2.18.6.2.1.2
VPI value for side A of an ATM-to-ATM PVC VPC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmPvcVpcIfB		3.1.1751.2.18.6.2.1.3
Interface index for side B of an ATM-to-ATM PVC VPC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmPvcVpcVpiB		3.1.1751.2.18.6.2.1.4
VPI value for side B of an ATM-to-ATM PVC VPC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmPvcVpcServiceTypeA2B		3.1.1751.2.18.6.2.1.5
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9), cbr1(10)

atmPvcVpcSarTypeA2B		3.1.1751.2.18.6.2.1.6
SAR Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmPvcVpcPeakCellRateA2B		3.1.1751.2.18.6.2.1.8
peak rate - side A, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVpcSusCellRateA2B		3.1.1751.2.18.6.2.1.9
sustained rate - side A, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVpcMaxBurstSizeA2B		3.1.1751.2.18.6.2.1.10
maximum burst size - side A, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVpcServiceTypeB2A		3.1.1751.2.18.6.2.1.11
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9), cbr1(10)

atmPvcVpcSarTypeB2A		3.1.1751.2.18.6.2.1.12
SAR Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmPvcVpcPeakCellRateB2A		3.1.1751.2.18.6.2.1.14
peak rate - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVpcSusCellRateB2A		3.1.1751.2.18.6.2.1.15
sustained rate - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVpcMaxBurstSizeB2A		3.1.1751.2.18.6.2.1.16
maximum burst size - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmPvcVpcType		3.1.1751.2.18.6.2.1.17
security feature type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nonsecured(1), secured(2)

atmPvcVpcFlow		3.1.1751.2.18.6.2.1.18
flow type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), pointToMultipointA2B(3)

atmPvcVpcRowStatus		3.1.1751.2.18.6.2.1.19
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

atmPvcVpcConnectionStatus		3.1.1751.2.18.6.2.1.20
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

atmPvcVpcOamStatus		3.1.1751.2.18.6.2.1.21
Indicates the OAM monitoring status of side A. The 5 possible states are: Unsupp: No monitoring enabled. End-Pt: A side is only an end point, therefore it will respond to AIS/RDI. Seg-Pt: A side is only a segment point, therefore it will only respond to maintenance OAM cells and not fault cells. End-Seg-Pt: A side is both an end point and a segment point. Intermediate-Pt: It will only generate AIS during local failure. For ATM-to-ATM connections the OAM status will be symmetric on both sides of the connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), seg-Pt(3), end-Seg-Pt(4), intermediate-Pt(5), intra-Segment-Pt(6)

atmPvcVpcDualHomed		3.1.1751.2.18.6.2.1.22
Does this PVC need a backup Dual homing PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(1), yes(2)

atmPvcVpcViA		3.1.1751.2.18.6.2.1.23
VI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmPvcVpcViB		3.1.1751.2.18.6.2.1.24
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmPvcVpcCnfrmTypeA2B		3.1.1751.2.18.6.2.1.25
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

atmPvcVpcCnfrmTypeB2A		3.1.1751.2.18.6.2.1.26
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

atmPvcVpcVUNIA		3.1.1751.2.18.6.2.1.27
VUNI Id to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmPvcVpcVUNIB		3.1.1751.2.18.6.2.1.28
VUNI Id to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmPvcVpcOamStatusB		3.1.1751.2.18.6.2.1.29
Indicates the Oam monitoring status of side B of an internal connection. Refer to ITU I.610 and Bellcore GR1248-CORE for definitions. The 6 possible states are: Unsupp: No OAM cell monitoring or generation enabled. All OAM flows are transparently passed through. End-Pt: Connection endPoint, segment flows are discarded. Seg-Pt: Segment endPoint. End-Seg-Pt: Connection endPoint that is also a segment endPoint. Intermediate-Pt: Connecting point, that is outside any segment. Generates only ete flows. Intra-Segment-Pt: Connecting point with a segment. Generates ete as well as segment flows.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), seg-Pt(3), end-Seg-Pt(4), intermediate-Pt(5), intra-Segment-Pt(6)

atmPvcVpcOAMConnEndPtStatusA		3.1.1751.2.18.6.2.1.30
Connection endpoint side A status. Valid only at connection endpoint.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ete-active(1), ete-ais-state(2), ete-rdi-state(3), ete-ais-rdi-state(4)

atmPvcVpcOAMConnEndPtStatusB		3.1.1751.2.18.6.2.1.31
Connection endpoint side B status. Valid only at connection endpoint.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ete-active(1), ete-ais-state(2), ete-rdi-state(3), ete-ais-rdi-state(4)

atmPvcVpcOAMConnSegEndPtStatusA		3.1.1751.2.18.6.2.1.32
Segment endpoint side A status. Valid only at segment/connection endpoints.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	seg-active(1), seg-ais-state(2), seg-rdi-state(3), seg-ais-rdi-state(4)

atmPvcVpcOAMConnSegEndPtStatusB		3.1.1751.2.18.6.2.1.33
Segment endpoint side B status. Valid only at segment/connection endpoints.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	seg-active(1), seg-ais-state(2), seg-rdi-state(3), seg-ais-rdi-state(4)

atmPvcVpcConnFailureCauseA		3.1.1751.2.18.6.2.1.34
connestion status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

atmPvcVpcConnFailureCauseB		3.1.1751.2.18.6.2.1.35
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

atmPvcVpcTrafficShapingA2B		3.1.1751.2.18.6.2.1.36
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmPvcVpcTrafficShapingB2A		3.1.1751.2.18.6.2.1.37
Traffic Shaping Support in the B2A direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmSvcVccTable		3.1.1751.2.18.6.3
Table of atm connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmSvcVccEntry

atmSvcVccEntry		3.1.1751.2.18.6.3.1
Row definition of atm connections
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmSvcVccEntry

atmSvcVccIfA		3.1.1751.2.18.6.3.1.1
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmSvcVccVpiA		3.1.1751.2.18.6.3.1.2
atm path identifier - side A
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmSvcVccVciA		3.1.1751.2.18.6.3.1.3
atm channel identifier - side A
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmSvcVccIfB		3.1.1751.2.18.6.3.1.4
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmSvcVccVpiB		3.1.1751.2.18.6.3.1.5
atm path identifier - side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmSvcVccVciB		3.1.1751.2.18.6.3.1.6
atm channel identifier - side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmSvcVccServiceTypeA2B		3.1.1751.2.18.6.3.1.7
service type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9), cbr1(10)

atmSvcVccSarTypeA2B		3.1.1751.2.18.6.3.1.8
sar type - A to B direction
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmSvcVccPeakCellRateA2B		3.1.1751.2.18.6.3.1.10
peak rate - side A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccSusCellRateA2B		3.1.1751.2.18.6.3.1.11
sustained rate - side A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccMaxBurstSizeA2B		3.1.1751.2.18.6.3.1.12
maximum burst size - side A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccServiceTypeB2A		3.1.1751.2.18.6.3.1.13
service type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9), cbr1(10)

atmSvcVccSarTypeB2A		3.1.1751.2.18.6.3.1.14
sar type - B to A direction
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmSvcVccPeakCellRateB2A		3.1.1751.2.18.6.3.1.16
peak rate - side B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccSusCellRateB2A		3.1.1751.2.18.6.3.1.17
sustained rate - side B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.3.1.18
maximum burst size - side B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccFlow		3.1.1751.2.18.6.3.1.19
flow type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	duplex(1), pointToMultipoint(2)

atmSvcVccType		3.1.1751.2.18.6.3.1.20
type of connection
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nonsecured(1), secured(2)

atmSvcVccConnectionStatus		3.1.1751.2.18.6.3.1.21
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

atmSvcVccViA		3.1.1751.2.18.6.3.1.22
VI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmSvcVccViB		3.1.1751.2.18.6.3.1.23
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmSvcVccCnfrmTypeA2B		3.1.1751.2.18.6.3.1.24
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

atmSvcVccCnfrmTypeB2A		3.1.1751.2.18.6.3.1.25
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

atmSvcVccVUNIA		3.1.1751.2.18.6.3.1.26
VUNI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmSvcVccVUNIB		3.1.1751.2.18.6.3.1.27
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmSvcVccTrafficShapingA2B		3.1.1751.2.18.6.3.1.28
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmSvcVccTrafficShapingB2A		3.1.1751.2.18.6.3.1.29
Traffic Shaping Support in the B2A direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ipAtmAppPvcVccTable		3.1.1751.2.18.6.4
Table about in-band management atm connection entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpAtmAppPvcVccEntry

ipAtmAppPvcVccEntry		3.1.1751.2.18.6.4.1
Row definition of in-band management atm connection attribution.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAtmAppPvcVccEntry

ipAtmAppPvcVccDestAddrA		3.1.1751.2.18.6.4.1.1
Destination IP address of an in-band management- atm connection. Value is and IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

ipAtmAppPvcVccSubnetMaskA		3.1.1751.2.18.6.4.1.2
The subnet mask of the destination IP address. Value is an IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

ipAtmAppPvcVccIfB		3.1.1751.2.18.6.4.1.3
Interface index for side B, the atm side, of an in-band management-atm connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccVpiB		3.1.1751.2.18.6.4.1.4
VPI value for side B, the atm side, of an in-band management-atm connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

ipAtmAppPvcVccVciB		3.1.1751.2.18.6.4.1.5
VCI value for side B, the atm side, of an in-band management-atm connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

ipAtmAppPvcVccServiceTypeA2B		3.1.1751.2.18.6.4.1.6
Service type from side A to B
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-express(2)

ipAtmAppPvcVccServiceTypeB2A		3.1.1751.2.18.6.4.1.7
Service type from side B to A
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-express(2), gfr2(3)

ipAtmAppPvcVccPeakCellRateB2A		3.1.1751.2.18.6.4.1.8
peak rate - side B
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccSusCellRateB2A		3.1.1751.2.18.6.4.1.9
sustained rate - side B
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.4.1.10
maximum burst size - side B
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccType		3.1.1751.2.18.6.4.1.11
Indicated in-band management atm connection type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(0), backup(1)

ipAtmAppPvcVccRowStatus		3.1.1751.2.18.6.4.1.12
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

ipAtmAppPvcVccConnectionStatus		3.1.1751.2.18.6.4.1.13
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

ipAtmAppPvcVccDualHomed		3.1.1751.2.18.6.4.1.14
Does this PVC need a backup Dual homing PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(1), yes(2)

ipAtmAppPvcVccViB		3.1.1751.2.18.6.4.1.15
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

ipAtmAppPvcVccCnfrmTypeB2A		3.1.1751.2.18.6.4.1.16
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

ipAtmAppPvcVccVUNIB		3.1.1751.2.18.6.4.1.17
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

ipAtmAppPvcVccMfsB2A		3.1.1751.2.18.6.4.1.18
Maximum Frame Size for GFR traffic
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

ipAtmAppPvcVccConnFailureCauseB		3.1.1751.2.18.6.4.1.19
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

ipAtmAppPvcVccTrafficShapingA2B		3.1.1751.2.18.6.4.1.20
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

ipAtmAppPvcVccOamStatus		3.1.1751.2.18.6.4.1.21
Indicates the OAM monitoring status. The 3 possible states are: Unsupp: No monitoring enabled. End-Pt: A side is only an end point, therefore it will respond to AIS/RDI. End-Seg-Pt: Connection endPoint that is also a segment endPoint.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), end-Seg-Pt(3)

ipAtmAppSvcVccTable		3.1.1751.2.18.6.5
Table of SVC VCC connection entries
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpAtmAppSvcVccEntry

ipAtmAppSvcVccEntry		3.1.1751.2.18.6.5.1
Row definition of SVC VCC connection attribution.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAtmAppSvcVccEntry

ipAtmAppSvcVccDestAddrA		3.1.1751.2.18.6.5.1.1
Destination IP address,value is IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

ipAtmAppSvcVccSubnetMaskA		3.1.1751.2.18.6.5.1.2
The subnet mask of the destination IP address. Value is an IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

ipAtmAppSvcVccIfB		3.1.1751.2.18.6.5.1.3
interface index (slot/port/channel) SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccVpiB		3.1.1751.2.18.6.5.1.4
atm path identifier - side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

ipAtmAppSvcVccVciB		3.1.1751.2.18.6.5.1.5
atm channel identifier - side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

ipAtmAppSvcVccServiceTypeA2B		3.1.1751.2.18.6.5.1.6
Service type from side A to B.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ubr(1), vbr-express(2)

ipAtmAppSvcVccServiceTypeB2A		3.1.1751.2.18.6.5.1.7
Service type from side B to A.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ubr(1), vbr-express(2)

ipAtmAppSvcVccPeakCellRateB2A		3.1.1751.2.18.6.5.1.8
peak rate - side B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccSusCellRateB2A		3.1.1751.2.18.6.5.1.9
sustained rate - side B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.5.1.10
maximum burst size - side B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccType		3.1.1751.2.18.6.5.1.11
Type of using SVC VCC connection.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(0), backup(1)

ipAtmAppSvcVccConnectionStatus		3.1.1751.2.18.6.5.1.12
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

ipAtmAppSvcVccViB		3.1.1751.2.18.6.5.1.13
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

ipAtmAppSvcVccCnfrmTypeB2A		3.1.1751.2.18.6.5.1.14
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

ipAtmAppSvcVccVUNIB		3.1.1751.2.18.6.5.1.15
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

ipAtmAppSvcVccTrafficShapingA2B		3.1.1751.2.18.6.5.1.16
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cirEmAtmPvcVccTable		3.1.1751.2.18.6.6
Table of Circuit Emulation to ATM VCCs
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirEmAtmPvcVccEntry

cirEmAtmPvcVccEntry		3.1.1751.2.18.6.6.1
Row definition of circuit emulation to atm connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	CirEmAtmPvcVccEntry

cirEmAtmPvcVccIfA		3.1.1751.2.18.6.6.1.1
Interface index for side A, the circuit emulation side, of a circuit emulation-atm PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmAtmPvcVccIfB		3.1.1751.2.18.6.6.1.2
Interface index for side B, the atm side, of a circuit emulation-atm PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmAtmPvcVccVpiB		3.1.1751.2.18.6.6.1.3
VPI value for side B, the atm side, of a circuit emulation-atm PVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

cirEmAtmPvcVccVciB		3.1.1751.2.18.6.6.1.4
VCI value for side B, the atm side, of a circuit emulation-atm PVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

cirEmAtmPvcVccServiceType		3.1.1751.2.18.6.6.1.5
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cbr-1(1), cbr-2(2), cbr-3(3), cbr-4(4)

cirEmAtmPvcVccVoiceCompressionA2B		3.1.1751.2.18.6.6.1.6
Voice Compression Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g726-16k(2), g726-24k(3), g726-32k(4), g726-40k(5), g729a-8k(6)

cirEmAtmPvcVccSilenceDetectionA2B		3.1.1751.2.18.6.6.1.7
silence detection off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cirEmAtmPvcVccEchoCancellationA2B		3.1.1751.2.18.6.6.1.8
Echo Cancellation Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g165-nearEnd(2), g168(3)

cirEmAtmPvcVccFlow		3.1.1751.2.18.6.6.1.9
Flow Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), simplexB2A(3), pointToMultipointA2B(4), pointToMultipointB2A(5)

cirEmAtmPvcVccRowStatus		3.1.1751.2.18.6.6.1.10
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

cirEmAtmPvcVccCngToneDetectionA2B		3.1.1751.2.18.6.6.1.11
Calling Tone Detection Algorithm, one of the enum value, g726-32k(3) is obsoleted on 01Mar99 such that user would not be able to configure CE-ATM.Fax Relay is to allow detection of fax Calling Tones. In faxRelay Mode only Fax calling tone is detected . In fxRlyMdmBypass faxRelay is detected and Modem is done in bypass mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), bypass(2), g726-32k(3), faxRelay(4), fxRlyMdmBypass(5)

cirEmAtmPvcVccCodingTranslationA2B		3.1.1751.2.18.6.6.1.12
Coding rule translation type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLaw2muLaw(2), aLaw2aLaw(3), muLaw2aLaw(4), aLaw2muLaw(5)

cirEmAtmPvcVccVoiceCompressionB2A		3.1.1751.2.18.6.6.1.13
Voice Compression Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g726-16k(2), g726-24k(3), g726-32k(4), g726-40k(5), g729a-8k(6)

cirEmAtmPvcVccSilenceDetectionB2A		3.1.1751.2.18.6.6.1.14
silence detection off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cirEmAtmPvcVccEchoCancellationB2A		3.1.1751.2.18.6.6.1.15
Echo Cancellation Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g165-nearEnd(2), g168(3)

cirEmAtmPvcVccCngToneDetectionB2A		3.1.1751.2.18.6.6.1.16
Calling Tone Detection Algorithm, one of the enum value, g726-32k(3) is obsoleted on 01Mar99 such that user would not be able to configure CE-ATM.Fax Relay is to allow detection of fax Calling Tones. In faxRelay Mode only Fax calling tone is detected . In fxRlyMdmBypass faxRelay is detected and Modem is done in bypass mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), bypass(2), g726-32k(3), faxRelay(4), fxRlyMdmBypass(5)

cirEmAtmPvcVccCodingTranslationB2A		3.1.1751.2.18.6.6.1.17
Coding rule translation type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLaw2muLaw(2), aLaw2aLaw(3), muLaw2aLaw(4), aLaw2muLaw(5)

cirEmAtmPvcVccSarTypeB		3.1.1751.2.18.6.6.1.18
This field will only be used when selecting voice compression, in other cases it will be set to aal1.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal2(3), aal1(4), aal2Std(5)

cirEmAtmPvcVccConnectionStatus		3.1.1751.2.18.6.6.1.19
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

cirEmAtmPvcVccDualHomed		3.1.1751.2.18.6.6.1.20
Does this PVC need a backup Dual homing PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(1), yes(2)

cirEmAtmPvcVccOamStatus		3.1.1751.2.18.6.6.1.21
Indicates the OAM monitoring status of side A. The 2 possible states are: Unsupp: No monitoring enabled. End-Pt: A side is only an end point, therefore it will respond to AIS/RDI.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), end-Seg-Pt(3)

cirEmAtmPvcVccViB		3.1.1751.2.18.6.6.1.22
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

cirEmAtmPvcVccCnfrmTypeB2A		3.1.1751.2.18.6.6.1.23
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

cirEmAtmPvcVccVUNIB		3.1.1751.2.18.6.6.1.24
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cirEmAtmPvcVccAal2Cid		3.1.1751.2.18.6.6.1.25
Aal2 Cid Used to pack ce chan in an Atm Trunk. This value will be unique per Atm Trunk. This field will be applicable when Aal type is chosen to be Standard Aal2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cirEmAtmPvcVccOAMConnEndPtStatus		3.1.1751.2.18.6.6.1.26
Connection endpoint status. Valid only at connection endpoint.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ete-active(1), ete-ais-state(2), ete-rdi-state(3), ete-ais-rdi-state(4)

cirEmAtmPvcVccOAMConnSegEndPtStatus		3.1.1751.2.18.6.6.1.27
Segment endpoint status. Valid only at segment/connection endpoints.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	seg-active(1), seg-ais-state(2), seg-rdi-state(3), seg-ais-rdi-state(4)

cirEmAtmPvcVccConnFailureCauseA		3.1.1751.2.18.6.6.1.28
connestion status reason code
Status: current	Access: read-only
OBJECT-TYPE
	ConnFailureCause

cirEmAtmPvcVccConnFailureCauseB		3.1.1751.2.18.6.6.1.29
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

cirEmAtmPvcVccDigitCollectTypeA2B		3.1.1751.2.18.6.6.1.30
Identify the digital tone setting. dtmf -- dual tone multifrequency dialed digits, mf -- multifrequency dialed digits, mf-r2-frwd -- R2 multifrequency forward dialed digits. mf-r2-bkwd-- R2 multifrequency backward dialed digits
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), dtmf(2), mf(3), mf-r2-frwd(4), mf-r2-bkwd(5)

cirEmAtmPvcVccDigitCollectTypeB2A		3.1.1751.2.18.6.6.1.31
Identify the digital tone setting. dtmf -- dual tone multifrequency dialed digits, mf -- multifrequency dialed digits, mf-r2-frwd -- R2 multifrequency forward dialed digits. mf-r2-bkwd-- R2 multifrequency backward dialed digits
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), dtmf(2), mf(3), mf-r2-frwd(4), mf-r2-bkwd(5)

cirEmAtmPvcVccEncodingStdA2B		3.1.1751.2.18.6.6.1.32
These are profiles defined according to standards User-Profile - No restrictions or checks, user freedom to choose any combination of Params. Atm Forum - These are profies defined by AF in document AF-VMOA-0145.000. In these cases the Identifiers are used and not the table numbers. Itu-t - These profiles are used from the I-366-2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	user(1), atmForum(2), itu-t(3)

cirEmAtmPvcVccEncodingStdB2A		3.1.1751.2.18.6.6.1.33
These are profiles defined according to standards User-Profile - No restrictions or checks, user freedom to choose any combination of Params. Atm Forum - These are profies defined by AF in document AF-VMOA-0145.000. In these cases the Identifiers are used and not the table numbers. Itu-t - These profiles are used from the I-366-2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	user(1), atmForum(2), itu-t(3)

cirEmAtmPvcVccEncodingProfileIdA2B		3.1.1751.2.18.6.6.1.34
These are profiles defined according to standards User-Profile - No restrictions or checks, user freedom to choose any combination of Params. Atm Forum - These are profies defined by AF in document AF-VMOA-0145.000. In these cases the Identifiers are used and not the table numbers. Itu-t - These profiles are used from the I-366-2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..256

cirEmAtmPvcVccEncodingProfileIdB2A		3.1.1751.2.18.6.6.1.35
These are profiles defined according to standards User-Profile - No restrictions or checks, user freedom to choose any combination of Params. Atm Forum - These are profies defined by AF in document AF-VMOA-0145.000. In these cases the Identifiers are used and not the table numbers. Itu-t - These profiles are used from the I-366-2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..256

frAtmPvcVccTable		3.1.1751.2.18.6.7
Table of frame relay to ATM IWF connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrAtmPvcVccEntry

frAtmPvcVccEntry		3.1.1751.2.18.6.7.1
Row definition of frame relay to ATM IWF connections
Status: current	Access: not-accessible
OBJECT-TYPE
	FrAtmPvcVccEntry

frAtmPvcVccIfA		3.1.1751.2.18.6.7.1.1
Interface index for side A, the frame relay side, of a frame relay-atm PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frAtmPvcVccDlciA		3.1.1751.2.18.6.7.1.2
DLCI value for side A, the frame relay side, of a frame relay-atm PVC VCC connection. Valid range is a number between 0 and 1023.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

frAtmPvcVccIfB		3.1.1751.2.18.6.7.1.3
Interface index for side B, the atm side, of a frame relay-atm PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frAtmPvcVccVpiB		3.1.1751.2.18.6.7.1.4
VPI value for side B, the atm side, of a frame relay-atm PVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

frAtmPvcVccVciB		3.1.1751.2.18.6.7.1.5
VCI value for side B, the atm side, of a frame relay-atm PVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

frAtmPvcVccMaxFrameSizeIn		3.1.1751.2.18.6.7.1.6
The value of this object is the size in octets of the largest frame relay information field for this PVC in the ingress direction (out of the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmPvcVccBcIn		3.1.1751.2.18.6.7.1.7
The value of this object is equal to the committed burst size (Bc) parameter (measured in bits) for this PVC in the ingress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmPvcVccBeIn		3.1.1751.2.18.6.7.1.8
The value of this object is equal to the excess burst size (Be) parameter (measured in bits) for this PVC in the ingress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmPvcVccCirIn		3.1.1751.2.18.6.7.1.9
The value of this object is equal to the committed information rate (CIR) parameter (measured in bits per second) for this PVC in the ingress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmPvcVccMaxFrameSizeOut		3.1.1751.2.18.6.7.1.10
The value of this object is the size in octets of the largest frame relay information field for this PVC in the egress direction (out of the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmPvcVccBcOut		3.1.1751.2.18.6.7.1.11
The value of this object is equal to the committed burst size (Bc) parameter (measured in bits) for this PVC in the egress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmPvcVccBeOut		3.1.1751.2.18.6.7.1.12
The value of this object is equal to the excess burst size (Be) parameter (measured in bits) for this PVC in the egress direction (into the frame relay UNI)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmPvcVccCirOut		3.1.1751.2.18.6.7.1.13
The value of this object is equal to the committed information rate (CIR) parameter (measured in bits per second) for this PVC in the egress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmPvcVccServiceType		3.1.1751.2.18.6.7.1.14
service type, Frame relay traffic is carried by VBR type of service only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), gfr2(7)

frAtmPvcVccFlow		3.1.1751.2.18.6.7.1.15
Flow Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), simplexB2A(3)

frAtmPvcVccRowStatus		3.1.1751.2.18.6.7.1.16
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

frAtmPvcVccTimeLenIn		3.1.1751.2.18.6.7.1.17
The time interval over which CIR and the burst sizes (Bc and Be) are measured in the A2B direction. The unit is milliseconds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	64..4000

frAtmPvcVccInterWorkingFuncIn		3.1.1751.2.18.6.7.1.18
InterWorking function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	frf8-Transl(1), frf8-Pass(2), frf5(3)

frAtmPvcVccTimeLenOut		3.1.1751.2.18.6.7.1.19
The time interval over which CIR and the burst sizes (Bc and Be) are measured in the A2B direction. The unit is milliseconds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	64..4000

frAtmPvcVccInterWorkingFuncOut		3.1.1751.2.18.6.7.1.20
InterWorking function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	frf8-Transl(1), frf8-Pass(2), frf5(3)

frAtmPvcVccPeakCellRateA2B		3.1.1751.2.18.6.7.1.21
Peak cell rate - side A, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccSusCellRateA2B		3.1.1751.2.18.6.7.1.22
Sustained cell rate - side A, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccMaxBurstSizeA2B		3.1.1751.2.18.6.7.1.23
Maximum burst size - side A, in cells, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccPeakCellRateB2A		3.1.1751.2.18.6.7.1.24
Peak cell rate - side B, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccSusCellRateB2A		3.1.1751.2.18.6.7.1.25
Sustained cell rate - side B, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.7.1.26
Maximum burst size - side B, in cells, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccConnectionStatus		3.1.1751.2.18.6.7.1.27
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

frAtmPvcVccDualHomed		3.1.1751.2.18.6.7.1.28
Does this PVC need a backup Dual homing PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(1), yes(2)

frAtmPvcVccOamStatus		3.1.1751.2.18.6.7.1.29
Indicates the OAM monitoring status of side A. The 2 possible states are: Unsupp: No monitoring enabled. End-Pt: A side is only an end point, therefore it will respond to AIS/RDI.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), end-Seg-Pt(3)

frAtmPvcVccViB		3.1.1751.2.18.6.7.1.30
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

frAtmPvcVccCnfrmTypeB2A		3.1.1751.2.18.6.7.1.31
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

frAtmPvcVccVUNIB		3.1.1751.2.18.6.7.1.32
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

frAtmPvcVccOAMConnEndPtStatus		3.1.1751.2.18.6.7.1.33
Connection endpoint status. Valid only at connection endpoint.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ete-active(1), ete-ais-state(2), ete-rdi-state(3), ete-ais-rdi-state(4)

frAtmPvcVccOAMSegEndPtStatus		3.1.1751.2.18.6.7.1.34
Segment endpoint status. Valid only at segment/connection endpoint.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	seg-active(1), seg-ais-state(2), seg-rdi-state(3), seg-ais-rdi-state(4)

frAtmPvcVccMfsB2A		3.1.1751.2.18.6.7.1.35
Maximum Frame Size for GFR traffic
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

frAtmPvcVccConnFailureCauseA		3.1.1751.2.18.6.7.1.36
connestion status reason code
Status: current	Access: read-only
OBJECT-TYPE
	FrConnFailureCause

frAtmPvcVccConnFailureCauseB		3.1.1751.2.18.6.7.1.37
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

frAtmPvcVccTrafficShapingA2B		3.1.1751.2.18.6.7.1.38
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

frFrPvcTable		3.1.1751.2.18.6.8
Table of frame relay to frame relay connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrFrPvcEntry

frFrPvcEntry		3.1.1751.2.18.6.8.1
Row definition of frame relay to frame relay PVC connections
Status: current	Access: not-accessible
OBJECT-TYPE
	FrFrPvcEntry

frFrPvcIfA		3.1.1751.2.18.6.8.1.1
Interface index for side A of a frame relay-frame relay PVC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frFrPvcDlciA		3.1.1751.2.18.6.8.1.2
DLCI value for side A of a frame relay-frame relay PVC connection. Valid range is a number between 0 and 1023.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

frFrPvcIfB		3.1.1751.2.18.6.8.1.3
Interface index for side B of a frame relay-frame relay PVC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frFrPvcDlciB		3.1.1751.2.18.6.8.1.4
DLCI value for side B of a frame relay-frame relay PVC connection. Valid range is a number between 0 and 1023.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

frFrPvcMaxFrameSizeA2B		3.1.1751.2.18.6.8.1.5
The value of this object is the size in octets of the largest frame relay information field for this PVC in the A to B direction.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frFrPvcBcA2B		3.1.1751.2.18.6.8.1.6
The value of this object is equal to the committed burst size (Bc) parameter (measured in bits) for this PVC in the A to B direction.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frFrPvcBeA2B		3.1.1751.2.18.6.8.1.7
The value of this object is equal to the excess burst size (Be) parameter (measured in bits) for this PVC in the A to B direction.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frFrPvcCirA2B		3.1.1751.2.18.6.8.1.8
The value of this object is equal to the committed information rate (CIR) parameter (measured in bits per second) for this PVC in the A to B direction.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frFrPvcMaxFrameSizeB2A		3.1.1751.2.18.6.8.1.9
The value of this object is the size in octets of the largest frame relay information field for this PVC in the B to A direction.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frFrPvcBcB2A		3.1.1751.2.18.6.8.1.10
The value of this object is equal to the committed burst size (Bc) parameter (measured in bits) for this PVC in the B to A direction.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frFrPvcBeB2A		3.1.1751.2.18.6.8.1.11
The value of this object is equal to the excess burst size (Be) parameter (measured in bits) for this PVC in the B to A direction.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frFrPvcCirB2A		3.1.1751.2.18.6.8.1.12
The value of this object is equal to the committed information rate (CIR) parameter (measured in bits per second) for this PVC in the B to A direction.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frFrPvcServiceType		3.1.1751.2.18.6.8.1.13
service type, Frame relay traffic is carried by VBR type of service only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6)

frFrPvcFlow		3.1.1751.2.18.6.8.1.14
Flow Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2)

frFrPvcRowStatus		3.1.1751.2.18.6.8.1.15
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

frFrPvcTimeLenA2B		3.1.1751.2.18.6.8.1.16
The time interval over which CIR and the burst sizes (Bc and Be) are measured in the A2B direction. The unit is milliseconds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	64..4000

frFrPvcInterWorkingFuncA2B		3.1.1751.2.18.6.8.1.17
InterWorking function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	frf8-Transl(1), frf8-Pass(2), frf5(3)

frFrPvcTimeLenB2A		3.1.1751.2.18.6.8.1.18
The time interval over which CIR and the burst sizes (Bc and Be) are measured in the A2B direction. The unit is milliseconds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	64..4000

frFrPvcInterWorkingFuncB2A		3.1.1751.2.18.6.8.1.19
InterWorking function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	frf8-Transl(1), frf8-Pass(2), frf5(3)

frFrPvcPeakCellRateA2B		3.1.1751.2.18.6.8.1.20
Peak cell rate - side A, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcSusCellRateA2B		3.1.1751.2.18.6.8.1.21
Sustained cell rate - side A, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcMaxBurstSizeA2B		3.1.1751.2.18.6.8.1.22
Maximum burst size - side A, in cells, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcPeakCellRateB2A		3.1.1751.2.18.6.8.1.23
Peak cell rate - side B, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcSusCellRateB2A		3.1.1751.2.18.6.8.1.24
Sustained cell rate - side B, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcMaxBurstSizeB2A		3.1.1751.2.18.6.8.1.25
Maximum burst size - side B, in cells, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcConnectionStatus		3.1.1751.2.18.6.8.1.26
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

frFrPvcConnFailureCauseA		3.1.1751.2.18.6.8.1.27
connestion status reason code
Status: current	Access: read-only
OBJECT-TYPE
	FrConnFailureCause

frFrPvcConnFailureCauseB		3.1.1751.2.18.6.8.1.28
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	FrConnFailureCause

vbrAtmPvcVccTable		3.1.1751.2.18.6.9
Table of terminal emulation to ATM network IWF connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrAtmPvcVccEntry

vbrAtmPvcVccEntry		3.1.1751.2.18.6.9.1
Row definition of terminal emulation to ATM network IWF connections
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrAtmPvcVccEntry

vbrAtmPvcVccIfA		3.1.1751.2.18.6.9.1.1
Interface index for side A, the variable bit rate side, of a variable bit rate-atm PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrAtmPvcVccIfB		3.1.1751.2.18.6.9.1.2
Interface index for side B, the atm side, of a variable bit rate-atm PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrAtmPvcVccVpiB		3.1.1751.2.18.6.9.1.3
VPI value for side B, the atm side, of a variable bit rate-atm PVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

vbrAtmPvcVccVciB		3.1.1751.2.18.6.9.1.4
VCI value for side B, the atm side, of a variable bit rate-atm PVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

vbrAtmPvcVccServiceType		3.1.1751.2.18.6.9.1.5
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), gfr2(7)

vbrAtmPvcVccPeakCellRateA2B		3.1.1751.2.18.6.9.1.6
peak cell rate - side A, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmPvcVccSusCellRateA2B		3.1.1751.2.18.6.9.1.7
sustained rate - side A, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmPvcVccMaxBurstSizeA2B		3.1.1751.2.18.6.9.1.8
maximum burst size - side A, in cells
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmPvcVccPeakCellRateB2A		3.1.1751.2.18.6.9.1.9
peak rate - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmPvcVccSusCellRateB2A		3.1.1751.2.18.6.9.1.10
sustained rate - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmPvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.9.1.11
maximum burst size - side B, in cells.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmPvcVccFlow		3.1.1751.2.18.6.9.1.12
Flow type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), simplexB2A(3)

vbrAtmPvcVccRowStatus		3.1.1751.2.18.6.9.1.13
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

vbrAtmPvcVccConnectionStatus		3.1.1751.2.18.6.9.1.14
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

vbrAtmPvcVccDualHomed		3.1.1751.2.18.6.9.1.15
Does this PVC need a backup Dual homing PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(1), yes(2)

vbrAtmPvcVccOamStatus		3.1.1751.2.18.6.9.1.16
Indicates the OAM monitoring status of side A. The 2 possible states are: Unsupp: No monitoring enabled. End-Pt: A side is only an end point, therefore it will respond to AIS/RDI. End-Seg-Pt: Connection endPoint that is also a segment endPoint.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), end-Seg-Pt(3)

vbrAtmPvcVccViB		3.1.1751.2.18.6.9.1.17
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

vbrAtmPvcVccCnfrmTypeB2A		3.1.1751.2.18.6.9.1.18
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

vbrAtmPvcVccVUNIB		3.1.1751.2.18.6.9.1.19
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

vbrAtmPvcVccOAMConnEndPtStatus		3.1.1751.2.18.6.9.1.20
Connection endpoint status. Valid only at connection endpoint.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ete-active(1), ete-ais-state(2), ete-rdi-state(3), ete-ais-rdi-state(4)

vbrAtmPvcVccOAMSegEndPtStatus		3.1.1751.2.18.6.9.1.21
Segment endpoint status. Valid only at segment/connection endpoint.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	seg-active(1), seg-ais-state(2), seg-rdi-state(3), seg-ais-rdi-state(4)

vbrAtmPvcVccMfsB2A		3.1.1751.2.18.6.9.1.22
Maximum Frame Size for GFR traffic
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

vbrAtmPvcVccConnFailureCauseA		3.1.1751.2.18.6.9.1.23
connestion status reason code
Status: current	Access: read-only
OBJECT-TYPE
	ConnFailureCause

vbrAtmPvcVccConnFailureCauseB		3.1.1751.2.18.6.9.1.24
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

vbrAtmPvcVccSarTypeB		3.1.1751.2.18.6.9.1.25
This field will be used to connect hdlc to atm directly when sar type is none or aal5 or go through dsp2 first when sar type is aal2Std.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), aal5(2), aal2Std(3)

vbrAtmPvcVccAal2Cid		3.1.1751.2.18.6.9.1.26
Aal2 Cid Used to pack hdlc chan in an Atm Trunk. This value will be unique per Atm Trunk. This field will be applicable when Aal type is chosen to be Standard Aal2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

vbrAtmPvcVccTrafficShapingA2B		3.1.1751.2.18.6.9.1.27
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cirEmCirEmPvcTable		3.1.1751.2.18.6.10
Table of Circuit Emulation to Circuit Emulation
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirEmCirEmPvcEntry

cirEmCirEmPvcEntry		3.1.1751.2.18.6.10.1
Row definition of circuit emulation to circuit emulation connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	CirEmCirEmPvcEntry

cirEmCirEmPvcIfA		3.1.1751.2.18.6.10.1.1
Interface index for side A of a circuit emulation-circuit emulation PVC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmCirEmPvcIfB		3.1.1751.2.18.6.10.1.2
Interface index for side B of a circuit emulation-circuit emulation PVC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmCirEmPvcEchoCancellationA2B		3.1.1751.2.18.6.10.1.5
Echo cancellation off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g165-nearEnd(2), g168(3)

cirEmCirEmPvcFlow		3.1.1751.2.18.6.10.1.6
Flow Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2)

cirEmCirEmPvcRowStatus		3.1.1751.2.18.6.10.1.7
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

cirEmCirEmPvcCodingTranslationA2B		3.1.1751.2.18.6.10.1.8
Coding rule translation type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLaw2muLaw(2), aLaw2aLaw(3), muLaw2aLaw(4), aLaw2muLaw(5)

cirEmCirEmPvcEchoCancellationB2A		3.1.1751.2.18.6.10.1.9
Echo cancellation off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g165-nearEnd(2), g168(3)

cirEmCirEmPvcCodingTranslationB2A		3.1.1751.2.18.6.10.1.10
Coding rule translation type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLaw2muLaw(2), aLaw2aLaw(3), muLaw2aLaw(4), aLaw2muLaw(5)

cirEmCirEmPvcConnectionStatus		3.1.1751.2.18.6.10.1.11
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

cirEmCirEmPvcInterworking		3.1.1751.2.18.6.10.1.12
CE - CE interworking enable/disabled
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cirEmCirEmPvcServiceType		3.1.1751.2.18.6.10.1.13
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cbr-1(1), cbr-2(2), cbr-3(3), cbr-4(4)

cirEmCirEmPvcConnFailureCauseA		3.1.1751.2.18.6.10.1.14
connestion status reason code
Status: current	Access: read-only
OBJECT-TYPE
	ConnFailureCause

cirEmCirEmPvcConnFailureCauseB		3.1.1751.2.18.6.10.1.15
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	ConnFailureCause

vbrVbrPvcTable		3.1.1751.2.18.6.11
Table of terminal emulation to ATM network IWF connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrVbrPvcEntry

vbrVbrPvcEntry		3.1.1751.2.18.6.11.1
Row definition of terminal emulation to ATM network IWF connections
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrVbrPvcEntry

vbrVbrPvcIfA		3.1.1751.2.18.6.11.1.1
Interface index for side A of a variable bit rate-variable bit rate PVC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrVbrPvcIfB		3.1.1751.2.18.6.11.1.2
Interface index for side B of a variable bit rate-variable bit rate PVC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrVbrPvcPeakCellRateA2B		3.1.1751.2.18.6.11.1.3
peak cell rate - side A, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrVbrPvcSusCellRateA2B		3.1.1751.2.18.6.11.1.4
sustained rate - side A, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrVbrPvcMaxBurstSizeA2B		3.1.1751.2.18.6.11.1.5
maximum burst size - side A, in cells
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrVbrPvcPeakCellRateB2A		3.1.1751.2.18.6.11.1.6
peak rate - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrVbrPvcSusCellRateB2A		3.1.1751.2.18.6.11.1.7
sustained rate - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrVbrPvcMaxBurstSizeB2A		3.1.1751.2.18.6.11.1.8
maximum burst size - side B, in cells.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrVbrPvcFlow		3.1.1751.2.18.6.11.1.9
Flow Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2)

vbrVbrPvcRowStatus		3.1.1751.2.18.6.11.1.10
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

vbrVbrPvcConnectionStatus		3.1.1751.2.18.6.11.1.11
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

vbrVbrPvcServiceType		3.1.1751.2.18.6.11.1.12
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6)

vbrVbrPvcConnFailureCauseA		3.1.1751.2.18.6.11.1.13
connestion status reason code
Status: current	Access: read-only
OBJECT-TYPE
	ConnFailureCause

vbrVbrPvcConnFailureCauseB		3.1.1751.2.18.6.11.1.14
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	ConnFailureCause

bridgeBridgePvcTable		3.1.1751.2.18.6.12
A table of bridge-bridge PVC connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BridgeBridgePvcEntry

bridgeBridgePvcEntry		3.1.1751.2.18.6.12.1
Row definitions of bridge-bridge PVC connection attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	BridgeBridgePvcEntry

bridgeBridgePvcIfA		3.1.1751.2.18.6.12.1.1
Interface index for side A of a bridge-bridge PVC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bridgeBridgePvcIfB		3.1.1751.2.18.6.12.1.2
Interface index for side B of a bridge-bridge PVC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bridgeBridgePvcRowStatus		3.1.1751.2.18.6.12.1.3
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

bridgeBridgePvcConnectionStatus		3.1.1751.2.18.6.12.1.4
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

bridgeBridgePvcConnFailureCauseA		3.1.1751.2.18.6.12.1.5
connestion status reason code
Status: current	Access: read-only
OBJECT-TYPE
	ConnFailureCause

bridgeBridgePvcConnFailureCauseB		3.1.1751.2.18.6.12.1.6
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	ConnFailureCause

bridgeAtmPvcVccTable		3.1.1751.2.18.6.13
Table of bridge Atm PVC VCC connection entries
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BridgeAtmPvcVccEntry

bridgeAtmPvcVccEntry		3.1.1751.2.18.6.13.1
Row definition of bridge atm PVC VCC connection attribution.
Status: current	Access: not-accessible
OBJECT-TYPE
	BridgeAtmPvcVccEntry

bridgeAtmPvcVccIfA		3.1.1751.2.18.6.13.1.1
Interface index for side A, the bridge side, of a bridge-atm PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccIfB		3.1.1751.2.18.6.13.1.2
Interface index for side B, the atm side, of a bridge-atm PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccVpiB		3.1.1751.2.18.6.13.1.3
VPI value for side B, the atm side, of a bridge-atm PVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

bridgeAtmPvcVccVciB		3.1.1751.2.18.6.13.1.4
VCI value for side B, the atm side, of a bridge-atm PVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

bridgeAtmPvcVccServiceType		3.1.1751.2.18.6.13.1.5
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), gfr2(7)

bridgeAtmPvcVccPeakCellRateB2A		3.1.1751.2.18.6.13.1.6
peak rate - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccSusCellRateB2A		3.1.1751.2.18.6.13.1.7
sustained rate - side B, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.13.1.8
maximum burst size - side B, in cells.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccRowStatus		3.1.1751.2.18.6.13.1.9
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

bridgeAtmPvcVccConnectionStatus		3.1.1751.2.18.6.13.1.10
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

bridgeAtmPvcVccDualHomed		3.1.1751.2.18.6.13.1.11
Does this PVC need a backup Dual homing PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(1), yes(2)

bridgeAtmPvcVccViB		3.1.1751.2.18.6.13.1.12
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

bridgeAtmPvcVccCnfrmTypeB2A		3.1.1751.2.18.6.13.1.14
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

bridgeAtmPvcVccVUNIB		3.1.1751.2.18.6.13.1.15
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

bridgeAtmPvcVccMfsB2A		3.1.1751.2.18.6.13.1.16
Maximum Frame Size for GFR traffic
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

bridgeAtmPvcVccConnFailureCauseA		3.1.1751.2.18.6.13.1.17
connestion status reason code
Status: current	Access: read-only
OBJECT-TYPE
	ConnFailureCause

bridgeAtmPvcVccConnFailureCauseB		3.1.1751.2.18.6.13.1.18
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

bridgeAtmPvcVccOamStatus		3.1.1751.2.18.6.13.1.19
Indicates the OAM monitoring status of side A. The 3 possible states are: Unsupp: No monitoring enabled. End-Pt: A side is only an end point, therefore End-Seg-Pt: A side is both an end point and a segment point.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), end-Seg-Pt(3)

bridgeAtmPvcVccTrafficShapingA2B		3.1.1751.2.18.6.13.1.20
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cirEmAtmBkPvcVccTable		3.1.1751.2.18.6.14
This table is used to manage CES DHPVC backup pvc.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirEmAtmBkPvcVccEntry

cirEmAtmBkPvcVccEntry		3.1.1751.2.18.6.14.1
An entry in the CES DHPVC table. There is one entry in the table corresponding to each active row in the cirEmAtmPvcVccTable for which the cirEmAtmPvcVccDualHomed object takes the value 'yes.'
Status: current	Access: not-accessible
OBJECT-TYPE
	CirEmAtmBkPvcVccEntry

cirEmAtmBkPvcVccIfB		3.1.1751.2.18.6.14.1.1
Interface index for side B, the atm side, of a backup circuit emulation-atm DHPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

cirEmAtmBkPvcVccVpiB		3.1.1751.2.18.6.14.1.2
VPI value for side B, the atm side, of a backup circuit emulation-atm DHPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

cirEmAtmBkPvcVccVciB		3.1.1751.2.18.6.14.1.3
VCI value for side B, the atm side, of a backup circuit emulation-atm DHPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

cirEmAtmBkPvcVccActivePvc		3.1.1751.2.18.6.14.1.4
Current active PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

cirEmAtmBkPvcVccAutoSwitch		3.1.1751.2.18.6.14.1.5
Auto switch back to primary link when primary link is recovered.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

cirEmAtmBkPvcVccRowStatus		3.1.1751.2.18.6.14.1.6
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

cirEmAtmBkPvcVccViB		3.1.1751.2.18.6.14.1.7
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

cirEmAtmBkPvcVccVUNIB		3.1.1751.2.18.6.14.1.8
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cirEmAtmBkPvcVccConnFailureCauseB		3.1.1751.2.18.6.14.1.9
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

vbrAtmBkPvcVccTable		3.1.1751.2.18.6.15
This table is used to manage terminal emulation DHPVC backup pvc.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrAtmBkPvcVccEntry

vbrAtmBkPvcVccEntry		3.1.1751.2.18.6.15.1
An entry in the terminal emulation DHPVC table. There is one entry in the table corresponding to each active row in the vbrAtmPvcVccTable for which the vbrAtmPvcVccDualHomed object takes the value 'yes'.
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrAtmBkPvcVccEntry

vbrAtmBkPvcVccIfB		3.1.1751.2.18.6.15.1.1
Interface index for side B, the atm side, of a backup terminal emulation-atm DHPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

vbrAtmBkPvcVccVpiB		3.1.1751.2.18.6.15.1.2
VPI value for side B, the atm side, of a backup terminal emulation-atm DHPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

vbrAtmBkPvcVccVciB		3.1.1751.2.18.6.15.1.3
VCI value for side B, the atm side, of a backup terminal emulation-atm DHPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

vbrAtmBkPvcVccActivePvc		3.1.1751.2.18.6.15.1.4
Current active PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

vbrAtmBkPvcVccAutoSwitch		3.1.1751.2.18.6.15.1.5
Auto switch back to primary link when primary link is recovered.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

vbrAtmBkPvcVccRowStatus		3.1.1751.2.18.6.15.1.6
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

vbrAtmBkPvcVccViB		3.1.1751.2.18.6.15.1.7
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

vbrAtmBkPvcVccVUNIB		3.1.1751.2.18.6.15.1.8
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

vbrAtmBkPvcVccConnFailureCauseB		3.1.1751.2.18.6.15.1.9
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

atmSpvcVccAddrTable		3.1.1751.2.18.6.16
Table of SPVC ATM network interface addresses.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmSpvcVccAddrEntry

atmSpvcVccAddrEntry		3.1.1751.2.18.6.16.1
Row definition of ATM SPVC address table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmSpvcVccAddrEntry

atmSpvcVccIfA		3.1.1751.2.18.6.16.1.1
Interface index for side A of an ATM SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmSpvcVccAtmPortAddr		3.1.1751.2.18.6.16.1.2
Local ATM port NSAP address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..20)

atmSpvcVccAddrRowStatus		3.1.1751.2.18.6.16.1.3
This is used to configure a NSAP address on the local port. Only when the address is configured can SPVC connections be established.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

atmSpvcVccTable		3.1.1751.2.18.6.17
Table of SPVC ATM virtual channel connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmSpvcVccEntry

atmSpvcVccEntry		3.1.1751.2.18.6.17.1
Row definition of ATM SPVC VCC connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmSpvcVccEntry

atmSpvcVccVpiA		3.1.1751.2.18.6.17.1.1
VPI value for side A of an ATM SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmSpvcVccVciA		3.1.1751.2.18.6.17.1.2
VCI value for side A of an ATM SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmSpvcVccIfB		3.1.1751.2.18.6.17.1.3
Interface index for side B of an ATM SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

atmSpvcVccVpiB		3.1.1751.2.18.6.17.1.4
VPI value for side B of an ATM SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

atmSpvcVccVciB		3.1.1751.2.18.6.17.1.5
VCI value for side B of an ATM SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

atmSpvcVccServiceTypeA2B		3.1.1751.2.18.6.17.1.6
Service type, ATM port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9), cbr1(10)

atmSpvcVccSarTypeA2B		3.1.1751.2.18.6.17.1.7
SAR type used in ATM adaption, ATM port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmSpvcVccPeakCellRateA2B		3.1.1751.2.18.6.17.1.8
Peak cell rate - side A, ATM port, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmSpvcVccSusCellRateA2B		3.1.1751.2.18.6.17.1.9
Sustained cell rate - side A, ATM port, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmSpvcVccMaxBurstSizeA2B		3.1.1751.2.18.6.17.1.10
Maximum burst size - side A, ATM port, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmSpvcVccFrwdErrCorrectionA2B		3.1.1751.2.18.6.17.1.11
Forward error correction scheme, ATM port side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4), autoHiQ(5), auto(6), autoLoQ(7)

atmSpvcVccServiceTypeB2A		3.1.1751.2.18.6.17.1.12
Service type, ATM trunk side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9), cbr1(10)

atmSpvcVccSarTypeB2A		3.1.1751.2.18.6.17.1.13
SAR type used in ATM adaption, ATM trunk side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmSpvcVccPeakCellRateB2A		3.1.1751.2.18.6.17.1.14
Peak cell rate - side B, ATM trunk, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmSpvcVccSusCellRateB2A		3.1.1751.2.18.6.17.1.15
Sustained cell rate - side B, ATM trunk, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmSpvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.17.1.16
Maximum burst size - side A, ATM trunk, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmSpvcVccFrwdErrCorrectionB2A		3.1.1751.2.18.6.17.1.17
Forward error correction scheme, ATM trunk side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4), autoHiQ(5), auto(6), autoLoQ(7)

atmSpvcVccFlow		3.1.1751.2.18.6.17.1.18
Type of flow, pointToMultipointA2B is for future support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), pointToMultipointA2B(3), simplexB2A(4)

atmSpvcVccType		3.1.1751.2.18.6.17.1.19
Type of connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nonsecured(1), secured(2)

atmSpvcVccConnType		3.1.1751.2.18.6.17.1.20
The type of connection: activeSvc - attempt calls, whenever not established. passiveSvc - accept calls.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	activeSvc(1), passiveSvc(2)

atmSpvcVccLeafReference		3.1.1751.2.18.6.17.1.21
An arbitrary integer which serves to distinguish the mulitple leaves attached to a root of a point-to-multipoint SPVC. If point-to-point SPVC, the value should be 1.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atmSpvcVccOperStatus		3.1.1751.2.18.6.17.1.22
The operation status of the connection: other - none of the types specified below. establishmentInProgress - connection is not operational, but call attempts are ongoing. connected - connection is currently operational. retriesExhausted - retry limit has been reached and call attempts have ceased. noAddressSupplied - no remote address has been configured, so no call attempts are initiated. lowerLayerDown - SPVC handler is not operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), establishmentInProgress(2), connected(3), retriesExhausted(4), noAddressSupplied(5), lowerLayerDown(6)

atmSpvcVccRowStatus		3.1.1751.2.18.6.17.1.23
Used to create and delete a soft PVC. When this object is set to 'active', an attempt is made to set up the soft PVC. When this object has the value 'active' and is set to another value, any setup or connection in-progress is released.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

atmSpvcVccViA		3.1.1751.2.18.6.17.1.24
VI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmSpvcVccViB		3.1.1751.2.18.6.17.1.25
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmSpvcVccTrafficShapingA2B		3.1.1751.2.18.6.17.1.26
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmSpvcVccTrafficShapingB2A		3.1.1751.2.18.6.17.1.27
Traffic Shaping Support in the B2A direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmSpvcVccActiveSvcTable		3.1.1751.2.18.6.18
The table used to manage active SVCs established across ATM networks between ATM entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmSpvcVccActiveSvcEntry

atmSpvcVccActiveSvcEntry		3.1.1751.2.18.6.18.1
An entry in the ATM active SVC table. There is one entry in the table corresponding to each active row in the atm SPVC VCC Table for which the atmSpvcVccConnType takes the value 'activeSvc'.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmSpvcVccActiveSvcEntry

atmSpvcVccRemoteAtmPortAddr		3.1.1751.2.18.6.18.1.1
Remote ATM port NSAP address, not meaningful if passive type of connection.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..20)

atmSpvcVccRemoteSelectType		3.1.1751.2.18.6.18.1.2
Indicates whether the remote VPI/VCI values are to be used at the destination. If 'any' is used, the destination switch will choose the VPI/VCI values. In such a case, once the SPVC is connected, the value of this object will change to 'required', such that the same VPI/VCI values will continue to be used even if the connection is torn down and re-established. If the value 'required' is specified, the values: atmSpvcVccRemoteVpi and atmSpvcVccRemoteVci, must be supplied and are used at the destination.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	required(1), any(2)

atmSpvcVccRemoteVpi		3.1.1751.2.18.6.18.1.3
VPI value to be used at the destination of an ATM SPVC VCC connection. Valid range is a number between 0 and 4095. If atmSpvcVccRemoteSelectType is configured as 'any', then this value is not relevant.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

atmSpvcVccRemoteVci		3.1.1751.2.18.6.18.1.4
VCI value to be used at the destination of an ATM SPVC VCC connection. Valid range is a number between 0 and 65535. If atmSpvcVccRemoteSelectType is configured as 'any', then this value is not relevant.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmSpvcVccRetryInterval		3.1.1751.2.18.6.18.1.5
The time to wait before attempting to establish the SVC after a previous failed call attempt. A value of 0 indicates retry will be attempted immediately.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

atmSpvcVccRetryLimit		3.1.1751.2.18.6.18.1.6
A maximum limit on how many retries should be attempted. A value of 0 indicates no limit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmSpvcVccRestart		3.1.1751.2.18.6.18.1.7
The active SVC is released, if necessary, and a new setup procedure is begun if 'restart', otherwise, noop.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noop(2)

atmSpvcVccRetryFailure		3.1.1751.2.18.6.18.1.8
Indicates how many attempts to establish the connection have failed. It it reset whenever a connection is successfully established or the SVC is restarted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccReleaseCause		3.1.1751.2.18.6.18.1.9
CAUSE field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..127

atmSpvcVccReleaseDiag		3.1.1751.2.18.6.18.1.10
DIAGNOSTICS field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

cirEmAtmSpvcVccTable		3.1.1751.2.18.6.19
Table of Circuit Emulation to ATM Soft PVCs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirEmAtmSpvcVccEntry

cirEmAtmSpvcVccEntry		3.1.1751.2.18.6.19.1
Row definition of circuit emulation to ATM SPVC connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	CirEmAtmSpvcVccEntry

cirEmAtmSpvcVccIfA		3.1.1751.2.18.6.19.1.1
Interface index for side A, the circuit emulation side, of a circuit emulation-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmAtmSpvcVccIfB		3.1.1751.2.18.6.19.1.2
Interface index for side B, the atm side, of a circuit emulation-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

cirEmAtmSpvcVccVpiB		3.1.1751.2.18.6.19.1.3
VPI value for side B, the atm side, of a circuit emulation-atm SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

cirEmAtmSpvcVccVciB		3.1.1751.2.18.6.19.1.4
VCI value for side B, the atm side, of a circuit emulation-atm SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

cirEmAtmSpvcVccVoiceCompressionA2B		3.1.1751.2.18.6.19.1.5
Voice Compression Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g726-16k(2), g726-24k(3), g726-32k(4), g726-40k(5)

cirEmAtmSpvcVccSilenceDetectionA2B		3.1.1751.2.18.6.19.1.6
silence detection off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cirEmAtmSpvcVccEchoCancellationA2B		3.1.1751.2.18.6.19.1.7
Echo Cancellation Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g165-nearEnd(2), g168(3)

cirEmAtmSpvcVccCngToneDetectionA2B		3.1.1751.2.18.6.19.1.8
Calling Tone Detection Algorithm, one of the enum value, g726-32k(3) is obsoleted on 01Mar99 such that user would not be able to configure CE-ATM
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), bypass(2), g726-32k(3)

cirEmAtmSpvcVccCodingTranslationA2B		3.1.1751.2.18.6.19.1.9
Coding rule translation type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLaw2muLaw(2), aLaw2aLaw(3), muLaw2aLaw(4), aLaw2muLaw(5)

cirEmAtmSpvcVccVoiceCompressionB2A		3.1.1751.2.18.6.19.1.10
Voice Compression Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g726-16k(2), g726-24k(3), g726-32k(4), g726-40k(5)

cirEmAtmSpvcVccSilenceDetectionB2A		3.1.1751.2.18.6.19.1.11
silence detection off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cirEmAtmSpvcVccEchoCancellationB2A		3.1.1751.2.18.6.19.1.12
Echo Cancellation Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g165-nearEnd(2), g168(3)

cirEmAtmSpvcVccCngToneDetectionB2A		3.1.1751.2.18.6.19.1.13
Calling Tone Detection Algorithm, one of the enum value, g726-32k(3) is obsoleted on 01Mar99 such that user would not be able to configure CE-ATM
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), bypass(2), g726-32k(3)

cirEmAtmSpvcVccCodingTranslationB2A		3.1.1751.2.18.6.19.1.14
Coding rule translation type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLaw2muLaw(2), aLaw2aLaw(3), muLaw2aLaw(4), aLaw2muLaw(5)

cirEmAtmSpvcVccFlow		3.1.1751.2.18.6.19.1.15
Flow Type, pointToMultipointA2B and pointToMultipointB2A are for future support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), simplexB2A(3), pointToMultipointA2B(4), pointToMultipointB2A(5)

cirEmAtmSpvcVccServiceType		3.1.1751.2.18.6.19.1.16
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cbr-1(1), cbr-2(2), cbr-3(3), cbr-4(4)

cirEmAtmSpvcVccConnType		3.1.1751.2.18.6.19.1.17
The type of connection: activeSvc - attempt calls, whenever not established; passiveSvc - accepts calls
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	activeSvc(1), passiveSvc(2)

cirEmAtmSpvcVccCePortAddr		3.1.1751.2.18.6.19.1.18
local CES port nsap address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..20)

cirEmAtmSpvcVccOperStatus		3.1.1751.2.18.6.19.1.19
other - none of the types specified below; establishmentInProgress - connection is not operational, but call attempts are ongoing; connected - connection is currently operational; retriesExhausted - retry limit has been reached and call attempts have ceased; noAddressSupplied - no remote address has been configured, so no call attempts are initiated; lowerLayerDown - SPVC handler is not operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), establishmentInProgress(2), connected(3), retriesExhausted(4), noAddressSupplied(5), lowerLayerDown(6)

cirEmAtmSpvcVccRowStatus		3.1.1751.2.18.6.19.1.20
Used to create and delete a soft PVCC. When this object is set to 'active' an attempt is made to set up the soft PVCC. When this object has the value 'active' and is set to another value, any set-up or connection in-progess is released.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

cirEmAtmSpvcVccViB		3.1.1751.2.18.6.19.1.21
VI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

cirEmAtmSpvcVccActiveSvcTable		3.1.1751.2.18.6.20
The table used to manage active SVCs established across ATM networks between CES entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirEmAtmSpvcVccActiveSvcEntry

cirEmAtmSpvcVccActiveSvcEntry		3.1.1751.2.18.6.20.1
An entry in the CES active SVC table. There is one entry in the table corresponding to each active row in the cirEmAtmSpvcVccRowStatus for which the cirEmAtmSpvcVccConnType takes the value 'activeSvc'.
Status: current	Access: not-accessible
OBJECT-TYPE
	CirEmAtmSpvcVccActiveSvcEntry

cirEmAtmSpvcVccRemoteCePortAddr		3.1.1751.2.18.6.20.1.1
The ATM address supporting the corresponding far end CES IWF process. If no address is supplied, no attempts to establish the active SVC are initiated.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..20)

cirEmAtmSpvcVccRetryInterval		3.1.1751.2.18.6.20.1.2
The time to wait before attempting to establish the SVC after previous failed call attempt. 0 indicates retry will be attempted immediately.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

cirEmAtmSpvcVccRetryLimit		3.1.1751.2.18.6.20.1.3
A maximum limit on how many retries. 0 indicates no limit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

cirEmAtmSpvcVccRestart		3.1.1751.2.18.6.20.1.4
restart, the active SVC is released if necessary and a new setup procedure is begun; or noop
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noop(2)

cirEmAtmSpvcVccRetryFailure		3.1.1751.2.18.6.20.1.5
Indicates how many attempts to establish the connection have failed. It is reset whenever a connection is successfully established or the SVC is restarted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccReleaseCause		3.1.1751.2.18.6.20.1.6
CAUSE field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..127

cirEmAtmSpvcVccReleaseDiag		3.1.1751.2.18.6.20.1.7
DIAGNOSTICS field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

vbrAtmSpvcVccTable		3.1.1751.2.18.6.21
Table of SPVC atm virtual channel connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrAtmSpvcVccEntry

vbrAtmSpvcVccEntry		3.1.1751.2.18.6.21.1
Row definition of atm SPVC VCC connections
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrAtmSpvcVccEntry

vbrAtmSpvcVccIfA		3.1.1751.2.18.6.21.1.1
Interface index for side A, the variable bit rate side, of a variable bit rate-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrAtmSpvcVccIfB		3.1.1751.2.18.6.21.1.2
Interface index for side B, the atm side, of a variable bit rate-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

vbrAtmSpvcVccVpiB		3.1.1751.2.18.6.21.1.3
VPI value for side B, the atm side, of a variable bit rate-atm SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

vbrAtmSpvcVccVciB		3.1.1751.2.18.6.21.1.4
VCI value for side B, the atm side, of a variable bit rate-atm SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

vbrAtmSpvcVccServiceType		3.1.1751.2.18.6.21.1.5
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt1(2), vbr-nrt2(3), vbr-rt1(4), vbr-rt2(5), vbr-express(6)

vbrAtmSpvcVccPeakCellRateA2B		3.1.1751.2.18.6.21.1.6
peak cell rate - side A, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccSusCellRateA2B		3.1.1751.2.18.6.21.1.7
sustained rate - side A, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccMaxBurstSizeA2B		3.1.1751.2.18.6.21.1.8
maximum burst size - side A, in cells
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccPeakCellRateB2A		3.1.1751.2.18.6.21.1.9
peak rate - side B, ATM trunk, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccSusCellRateB2A		3.1.1751.2.18.6.21.1.10
sustained rate - side B, ATM trunk, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.21.1.11
maximum burst size - side B, ATM trunk, in cells.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccFlow		3.1.1751.2.18.6.21.1.12
type of flow
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), simplexB2A(3)

vbrAtmSpvcVccConnType		3.1.1751.2.18.6.21.1.13
The type of connection: activeSvc - attempt calls, whenever not established; passiveSvc - accepts calls
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	activeSvc(1), passiveSvc(2)

vbrAtmSpvcVccVbrPortAddr		3.1.1751.2.18.6.21.1.14
local Vbr port nsap address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..20)

vbrAtmSpvcVccOperStatus		3.1.1751.2.18.6.21.1.15
other - none of the types specified below; establishmentInProgress - connection is not operational, but call attempts are ongoing; connected - connection is currently operational; retriesExhausted - retry limit has been reached and call attempts have ceased; noAddressSupplied - no remote address has been configured, so no call attempts are initiated; lowerLayerDown - SPVC handler is not operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), establishmentInProgress(2), connected(3), retriesExhausted(4), noAddressSupplied(5), lowerLayerDown(6)

vbrAtmSpvcVccRowStatus		3.1.1751.2.18.6.21.1.16
Used to create and delete a soft PVCC. When this object is set to 'active' an attempt is made to set up the soft PVCC. When this object has the value 'active' and is set to another value, any set-up or connection in-progess is released.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

vbrAtmSpvcVccViB		3.1.1751.2.18.6.21.1.17
VI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

vbrAtmSpvcVccTrafficShapingA2B		3.1.1751.2.18.6.21.1.18
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

vbrAtmSpvcVccActiveSvcTable		3.1.1751.2.18.6.22
The table used to manage active SVCs established across ATM networks between ATM entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrAtmSpvcVccActiveSvcEntry

vbrAtmSpvcVccActiveSvcEntry		3.1.1751.2.18.6.22.1
An entry in the Terminal Emulation ATM active SVC table. There is one entry in the table corresponding to each active row in the vbrAtmSpvcVccTable for which the vbrAtmSpvcVccConnType takes the value 'activeSvc'.
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrAtmSpvcVccActiveSvcEntry

vbrAtmSpvcVccRemoteVbrPortAddr		3.1.1751.2.18.6.22.1.1
remote VBR port nsap address implemening IWF, not meaningful if passive type of connection
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..20)

vbrAtmSpvcVccRetryInterval		3.1.1751.2.18.6.22.1.2
the time to wait before attempting to establish the SVC after previous failed call attempt. 0 indicates retry will be attempted immediately.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

vbrAtmSpvcVccRetryLimit		3.1.1751.2.18.6.22.1.3
a maximum limit on how many retries. 0 indicates no limit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

vbrAtmSpvcVccRestart		3.1.1751.2.18.6.22.1.4
restart, the active SVC is released if necessary and a new setup procedure is begun; or noop
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noop(2)

vbrAtmSpvcVccRetryFailure		3.1.1751.2.18.6.22.1.5
indicates how many attempts to establish the connection have failed. It is reset whenever a connection is successfully established or the SVC is restarted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccReleaseCause		3.1.1751.2.18.6.22.1.6
CAUSE field value of the last RELEASE message received for this SVC
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..127

vbrAtmSpvcVccReleaseDiag		3.1.1751.2.18.6.22.1.7
DIAGNOSTICS field value of the last RELEASE message received for this SVC
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

atmSpvcVccRlsTable		3.1.1751.2.18.6.23
This table is an extension of atmSpvcVccTable and is used to release a ATM-ATM SPVC connection without deleting the configured data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmSpvcVccRlsEntry

atmSpvcVccRlsEntry		3.1.1751.2.18.6.23.1
Row definition of CES SPVC release table. This entry is created whenever an entry is created in atmSpvcVccTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmSpvcVccRlsEntry

atmSpvcVccRelease		3.1.1751.2.18.6.23.1.1
Release the connnection established on the endpoint and if the endpoint is Active, do not retry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	release(1), noop(2)

cirEmAtmSpvcVccRlsTable		3.1.1751.2.18.6.24
This table is an extension of cirEmAtmSpvcVccTable and is used to release a TE-ATM SPVC connection without deleting the configured data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirEmAtmSpvcVccRlsEntry

cirEmAtmSpvcVccRlsEntry		3.1.1751.2.18.6.24.1
Row definition of CES SPVC release table. This entry is created whenever an entry is created in cirEmAtmSpvcVccTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	CirEmAtmSpvcVccRlsEntry

cirEmAtmSpvcVccRelease		3.1.1751.2.18.6.24.1.1
Release the connnection established on the endpoint and if the endpoint is Active, do not retry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	release(1), noop(2)

vbrAtmSpvcVccRlsTable		3.1.1751.2.18.6.25
This table is an extension of vbrAtmSpvcVccTable and is used to release a TE-ATM SPVC connection without deleting the configured data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrAtmSpvcVccRlsEntry

vbrAtmSpvcVccRlsEntry		3.1.1751.2.18.6.25.1
Row definition of TE SPVC release table. This entry is created whenever an entry is created in vbrAtmSpvcVccTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrAtmSpvcVccRlsEntry

vbrAtmSpvcVccRelease		3.1.1751.2.18.6.25.1.1
Release the connnection established on the endpoint and if the endpoint is Active, do not retry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	release(1), noop(2)

frAtmBkPvcVccTable		3.1.1751.2.18.6.26
This table is used to manage frame relay DHPVC backup pvc.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrAtmBkPvcVccEntry

frAtmBkPvcVccEntry		3.1.1751.2.18.6.26.1
An entry in the frame relay DHPVC table. There is one entry in the table corresponding to each active row in the frAtmPvcVccTable for which the frAtmPvcVccDualHomed object takes the value 'yes.'
Status: current	Access: not-accessible
OBJECT-TYPE
	FrAtmBkPvcVccEntry

frAtmBkPvcVccIfB		3.1.1751.2.18.6.26.1.1
Interface index for side B, the atm side, of a backup frame relay-atm DHPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

frAtmBkPvcVccVpiB		3.1.1751.2.18.6.26.1.2
VPI value for side B, the atm side, of a backup frame relay-atm DHPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

frAtmBkPvcVccVciB		3.1.1751.2.18.6.26.1.3
VCI value for side B, the atm side, of a backup frame relay-atm DHPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

frAtmBkPvcVccActivePvc		3.1.1751.2.18.6.26.1.4
Current active PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

frAtmBkPvcVccAutoSwitch		3.1.1751.2.18.6.26.1.5
Auto switch back to primary link when primary link is recovered.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

frAtmBkPvcVccRowStatus		3.1.1751.2.18.6.26.1.6
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

frAtmBkPvcVccViB		3.1.1751.2.18.6.26.1.7
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

frAtmBkPvcVccVUNIB		3.1.1751.2.18.6.26.1.8
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

frAtmBkPvcVccConnFailureCauseB		3.1.1751.2.18.6.26.1.9
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

atmBkPvcVccTable		3.1.1751.2.18.6.27
This table is used to manage ATM to ATM DHPVC backup pvc.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmBkPvcVccEntry

atmBkPvcVccEntry		3.1.1751.2.18.6.27.1
An entry in the ATM to ATM DHPVC table. There is one entry in the table corresponding to each active row in the atmPvcVccTable for which the atmPvcVccDualHomed object takes the value 'yes'.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmBkPvcVccEntry

atmBkPvcVccIfB		3.1.1751.2.18.6.27.1.1
Interface index for side B, the atm side, of a backup ATM-to-ATM DHPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

atmBkPvcVccVpiB		3.1.1751.2.18.6.27.1.2
VPI value for side B, the atm side, of a backup ATM-to-ATM DHPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

atmBkPvcVccVciB		3.1.1751.2.18.6.27.1.3
VCI value for side B, the atm side, of a backup ATM-to-ATM DHPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmBkPvcVccActivePvc		3.1.1751.2.18.6.27.1.4
Current active PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

atmBkPvcVccAutoSwitch		3.1.1751.2.18.6.27.1.5
Auto switch back to primary link when primary link is recovered.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

atmBkPvcVccRowStatus		3.1.1751.2.18.6.27.1.6
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

atmBkPvcVccViB		3.1.1751.2.18.6.27.1.7
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmBkPvcVccVUNIB		3.1.1751.2.18.6.27.1.8
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmBkPvcVccConnFailureCauseB		3.1.1751.2.18.6.27.1.9
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

atmBkPvcVpcTable		3.1.1751.2.18.6.28
This table is used to manage ATM to ATM DHPVC backup pvc.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmBkPvcVpcEntry

atmBkPvcVpcEntry		3.1.1751.2.18.6.28.1
An entry in the ATM to ATM DHPVC table. There is one entry in the table corresponding to each active row in the atmPvcVpcTable for which the atmPvcVpcDualHomed object takes the value 'yes'.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmBkPvcVpcEntry

atmBkPvcVpcIfB		3.1.1751.2.18.6.28.1.1
Interface index for side B of an ATM-to-ATM PVC VPC backup DHPVC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

atmBkPvcVpcVpiB		3.1.1751.2.18.6.28.1.2
VPI value for side B of an ATM-to-ATM PVC VPC backup DHPVC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

atmBkPvcVpcActivePvc		3.1.1751.2.18.6.28.1.3
Current active PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

atmBkPvcVpcAutoSwitch		3.1.1751.2.18.6.28.1.4
Auto switch back to primary link when primary link is recovered.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

atmBkPvcVpcRowStatus		3.1.1751.2.18.6.28.1.5
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

atmBkPvcVpcViB		3.1.1751.2.18.6.28.1.6
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmBkPvcVpcVUNIB		3.1.1751.2.18.6.28.1.7
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmBkPvcVpcConnFailureCauseB		3.1.1751.2.18.6.28.1.8
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

bridgeAtmBkPvcVccTable		3.1.1751.2.18.6.29
This table is used to manage bridge to atm DHPVC backup pvc.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BridgeAtmBkPvcVccEntry

bridgeAtmBkPvcVccEntry		3.1.1751.2.18.6.29.1
An entry in the bridge to atm DHPVC table. There is one entry in the table corresponding to each active row in the bridgeAtmPvcVccTable for which the bridgeAtmPvcVccDualHomed object takes the value 'yes'.
Status: current	Access: not-accessible
OBJECT-TYPE
	BridgeAtmBkPvcVccEntry

bridgeAtmBkPvcVccIfB		3.1.1751.2.18.6.29.1.1
Interface index for side B, the atm side, of a backup bridge-atm DHPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

bridgeAtmBkPvcVccVpiB		3.1.1751.2.18.6.29.1.2
VPI value for side B, the atm side, of a backup bridge-atm DHPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

bridgeAtmBkPvcVccVciB		3.1.1751.2.18.6.29.1.3
VCI value for side B, the atm side, of a backup bridge-atm DHPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

bridgeAtmBkPvcVccActivePvc		3.1.1751.2.18.6.29.1.4
Current active PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

bridgeAtmBkPvcVccAutoSwitch		3.1.1751.2.18.6.29.1.5
Auto switch back to primary link when primary link is recovered.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

bridgeAtmBkPvcVccRowStatus		3.1.1751.2.18.6.29.1.6
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

bridgeAtmBkPvcVccViB		3.1.1751.2.18.6.29.1.7
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

bridgeAtmBkPvcVccVUNIB		3.1.1751.2.18.6.29.1.8
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

bridgeAtmBkPvcVccConnFailureCauseB		3.1.1751.2.18.6.29.1.9
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

ipAtmBkAppPvcVccTable		3.1.1751.2.18.6.30
This table is used to manage in-band management to atm DHPVC backup pvc.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpAtmBkAppPvcVccEntry

ipAtmBkAppPvcVccEntry		3.1.1751.2.18.6.30.1
An entry in the in-band management to atm DHPVC table. There is one entry in the table corresponding to each active row in the ipAtmAppPvcVccTable for which the ipAtmAppPvcVccDualHomed object takes the value 'yes'.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAtmBkAppPvcVccEntry

ipAtmBkAppPvcVccIfB		3.1.1751.2.18.6.30.1.1
Interface index for side B, the atm side, of a backup in-band management-atm DHPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

ipAtmBkAppPvcVccVpiB		3.1.1751.2.18.6.30.1.2
VPI value for side B, the atm side, of a backup in-band management-atm DHPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

ipAtmBkAppPvcVccVciB		3.1.1751.2.18.6.30.1.3
VCI value for side B, the atm side, of a backup in-band management-atm DHPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

ipAtmBkAppPvcVccActivePvc		3.1.1751.2.18.6.30.1.4
Current active PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

ipAtmBkAppPvcVccAutoSwitch		3.1.1751.2.18.6.30.1.5
Auto switch back to primary link when primary link is recovered.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

ipAtmBkAppPvcVccRowStatus		3.1.1751.2.18.6.30.1.6
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

ipAtmBkAppPvcVccViB		3.1.1751.2.18.6.30.1.7
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

ipAtmBkAppPvcVccVUNIB		3.1.1751.2.18.6.30.1.8
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

ipAtmBkAppPvcVccConnFailureCauseB		3.1.1751.2.18.6.30.1.9
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

spvcAddrTable		3.1.1751.2.18.6.31
Table of SPVC network interface addresses.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SpvcAddrEntry

spvcAddrEntry		3.1.1751.2.18.6.31.1
Row definition of SPVC address table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SpvcAddrEntry

spvcAddrIfA		3.1.1751.2.18.6.31.1.1
Interface index for side A of an SPVC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

spvcAddrLocalPortAddr		3.1.1751.2.18.6.31.1.2
Local port NSAP address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..20)

spvcAddrRowStatus		3.1.1751.2.18.6.31.1.3
This is used to configure a NSAP address on the local port. Only when the address is configured can SPVC connections be established.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

frAtmSpvcVccTable		3.1.1751.2.18.6.32
Table of frame relay to ATM IWF connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrAtmSpvcVccEntry

frAtmSpvcVccEntry		3.1.1751.2.18.6.32.1
Row definition of frame relay to ATM IWF connections
Status: current	Access: not-accessible
OBJECT-TYPE
	FrAtmSpvcVccEntry

frAtmSpvcVccDlciA		3.1.1751.2.18.6.32.1.1
DLCI value for side A, the frame relay side, of a frame relay-atm SPVC VCC connection. Valid range is a number between 0 and 1023.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..1023

frAtmSpvcVccIfB		3.1.1751.2.18.6.32.1.2
Interface index for side B, the atm side, of a frame relay-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

frAtmSpvcVccVpiB		3.1.1751.2.18.6.32.1.3
VPI value for side B, the atm side, of a frame relay-atm SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

frAtmSpvcVccVciB		3.1.1751.2.18.6.32.1.4
VCI value for side B, the atm side, of a frame relay-atm SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

frAtmSpvcVccMaxFrameSizeIn		3.1.1751.2.18.6.32.1.5
The value of this object is the size in octets of the largest frame relay information field for this SPVC in the ingress direction (out of the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmSpvcVccBcIn		3.1.1751.2.18.6.32.1.6
The value of this object is equal to the committed burst size (Bc) parameter (measured in bits) for this SPVC in the ingress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmSpvcVccBeIn		3.1.1751.2.18.6.32.1.7
The value of this object is equal to the excess burst size (Be) parameter (measured in bits) for this SPVC in the ingress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmSpvcVccCirIn		3.1.1751.2.18.6.32.1.8
The value of this object is equal to the committed information rate (CIR) parameter (measured in bits per second) for this SPVC in the ingress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmSpvcVccMaxFrameSizeOut		3.1.1751.2.18.6.32.1.9
The value of this object is the size in octets of the largest frame relay information field for this SPVC in the egress direction (out of the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmSpvcVccBcOut		3.1.1751.2.18.6.32.1.10
The value of this object is equal to the committed burst size (Bc) parameter (measured in bits) for this SPVC in the egress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmSpvcVccBeOut		3.1.1751.2.18.6.32.1.11
The value of this object is equal to the excess burst size (Be) parameter (measured in bits) for this SPVC in the egress direction (into the frame relay UNI)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmSpvcVccCirOut		3.1.1751.2.18.6.32.1.12
The value of this object is equal to the committed information rate (CIR) parameter (measured in bits per second) for this SPVC in the egress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

frAtmSpvcVccServiceType		3.1.1751.2.18.6.32.1.13
service type, Frame relay traffic is carried by VBR type of service only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6)

frAtmSpvcVccFlow		3.1.1751.2.18.6.32.1.14
Flow Type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), simplexB2A(3)

frAtmSpvcVccTimeLenIn		3.1.1751.2.18.6.32.1.15
The time interval over which CIR and the burst sizes (Bc and Be) are measured in the A2B direction. The unit is milliseconds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	64..4000

frAtmSpvcVccTimeLenOut		3.1.1751.2.18.6.32.1.16
The time interval over which CIR and the burst sizes (Bc and Be) are measured in the A2B direction. The unit is milliseconds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	64..4000

frAtmSpvcVccPeakCellRateA2B		3.1.1751.2.18.6.32.1.17
Peak cell rate - side A, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccSusCellRateA2B		3.1.1751.2.18.6.32.1.18
Sustained cell rate - side A, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccMaxBurstSizeA2B		3.1.1751.2.18.6.32.1.19
Maximum burst size - side A, in cells, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccPeakCellRateB2A		3.1.1751.2.18.6.32.1.20
Peak cell rate - side B, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccSusCellRateB2A		3.1.1751.2.18.6.32.1.21
Sustained cell rate - side B, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.32.1.22
Maximum burst size - side B, in cells, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccInterWorkingFunc		3.1.1751.2.18.6.32.1.23
InterWorking function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	frf8-Transl(1), frf8-Pass(2), frf5(3)

frAtmSpvcVccConnType		3.1.1751.2.18.6.32.1.24
The type of connection: activeSvc - attempt calls, whenever not established; passiveSvc - accepts calls
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	activeSvc(1), passiveSvc(2)

frAtmSpvcVccOperStatus		3.1.1751.2.18.6.32.1.25
other - none of the types specified below; establishmentInProgress - connection is not operational, but call attempts are ongoing; connected - connection is currently operational; retriesExhausted - retry limit has been reached and call attempts have ceased; noAddressSupplied - no remote address has been configured, so no call attempts are initiated; lowerLayerDown - SPVC handler is not operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), establishmentInProgress(2), connected(3), retriesExhausted(4), noAddressSupplied(5), lowerLayerDown(6), waitingForCall(7), waitingForRetryTimer(8)

frAtmSpvcVccRowStatus		3.1.1751.2.18.6.32.1.26
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

frAtmSpvcVccRemoteFrPortAddr		3.1.1751.2.18.6.32.1.27
The ATM address supporting the corresponding far end FR IWF process. If no address is supplied, no attempts to establish the active SVC are initiated.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..20)

frAtmSpvcVccRemoteSelectType		3.1.1751.2.18.6.32.1.28
Indicates whether the remote DLCI/VPI/VCI values are to be used at the destination. If 'any' is used, the destination switch will choose the DLCI/VPI/VCI values. In such a case, once the SPVC is connected, the value of this object will change to 'required', such that the same DLCI/VPI/VCI values will continue to be used even if the connection is torn down and re-established. If the value 'required' is specified, the values: frAtmSpvcVccRemoteDlci or frAtmSpvcVccRemoteVpi and frAtmSpvcVccRemoteVci, must be supplied and are used at the destination.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	required(1), any(2)

frAtmSpvcVccRemoteDlci		3.1.1751.2.18.6.32.1.29
DLCI value to be used at the destination of an ATM SPVC VCC connection. Valid range is a number between 0 and 4095. If frAtmSpvcVccRemoteSelectType is configured as 'any', then this value is not relevant.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

frAtmSpvcVccRemoteVpi		3.1.1751.2.18.6.32.1.30
VPI value to be used at the destination of an ATM SPVC VCC connection. Valid range is a number between 0 and 4095. If frAtmSpvcVccRemoteSelectType is configured as 'any', then this value is not relevant.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

frAtmSpvcVccRemoteVci		3.1.1751.2.18.6.32.1.31
VCI value to be used at the destination of an ATM SPVC VCC connection. Valid range is a number between 0 and 65535. If frAtmSpvcVccRemoteSelectType is configured as 'any', then this value is not relevant.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

frAtmSpvcVccRetryInterval		3.1.1751.2.18.6.32.1.32
The time to wait before attempting to establish the SVC after previous failed call attempt. 0 indicates retry will be attempted immediately.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

frAtmSpvcVccRetryLimit		3.1.1751.2.18.6.32.1.33
A maximum limit on how many retries. 0 indicates no limit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

frAtmSpvcVccRestart		3.1.1751.2.18.6.32.1.34
restart, the active SVC is released if necessary and a new setup procedure is begun; or noop
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noop(2)

frAtmSpvcVccRetryFailure		3.1.1751.2.18.6.32.1.35
Indicates how many attempts to establish the connection have failed. It is reset whenever a connection is successfully established or the SVC is restarted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccReleaseCause		3.1.1751.2.18.6.32.1.36
CAUSE field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..127

frAtmSpvcVccReleaseDiag		3.1.1751.2.18.6.32.1.37
DIAGNOSTICS field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

frAtmSpvcVccRelease		3.1.1751.2.18.6.32.1.38
Release the connnection established on the endpoint and if the endpoint is Active, do not retry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	release(1), noop(2)

frAtmSpvcVccStatsCellsEncodedHiA		3.1.1751.2.18.6.32.1.39
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsCellsEncodedLoA		3.1.1751.2.18.6.32.1.40
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsCellsDecodedHiA		3.1.1751.2.18.6.32.1.41
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsCellsDecodedLoA		3.1.1751.2.18.6.32.1.42
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsInCellCountHiB		3.1.1751.2.18.6.32.1.43
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsInCellCountLoB		3.1.1751.2.18.6.32.1.44
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsOutCellCountHiB		3.1.1751.2.18.6.32.1.45
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsOutCellCountLoB		3.1.1751.2.18.6.32.1.46
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsTimer		3.1.1751.2.18.6.32.1.47
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsFramesDroppedA		3.1.1751.2.18.6.32.1.48
Number of frames dropped for a given DLCI for A2B direction, only applicable to the input side.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsOdometerCellsEncodedHiA		3.1.1751.2.18.6.32.1.49
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsOdometerCellsEncodedLoA		3.1.1751.2.18.6.32.1.50
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsOdometerCellsDecodedHiA		3.1.1751.2.18.6.32.1.51
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsOdometerCellsDecodedLoA		3.1.1751.2.18.6.32.1.52
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.6.32.1.53
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.6.32.1.54
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.6.32.1.55
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.6.32.1.56
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsOdometerTimer		3.1.1751.2.18.6.32.1.57
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsOdometerReset		3.1.1751.2.18.6.32.1.58
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

frAtmSpvcVccStatsAal5ErrFramesA		3.1.1751.2.18.6.32.1.59
Number of Aal5 Errored Frames, which are not dropped due to UPC in A2B dir, only applicable to Input Side
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsFramesTaggedA		3.1.1751.2.18.6.32.1.60
Number of Frames tagged due to UPC in A2B dir, only applicable to Input Side
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsCellsDroppedB		3.1.1751.2.18.6.32.1.61
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccStatsCellsTaggedB		3.1.1751.2.18.6.32.1.62
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmSpvcVccVUNIB		3.1.1751.2.18.6.32.1.63
VUNI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

frAtmSpvcVccTrafficShapingA2B		3.1.1751.2.18.6.32.1.64
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

frAtmSpvcVccPriority		3.1.1751.2.18.6.32.1.65
Priority of SPVC - priority-1 being highest priority .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	priority-1(1), priority-2(2), priority-3(3), priority-4(4)

atmAtmSpvcVccTable		3.1.1751.2.18.6.33
Table of SPVC ATM virtual channel connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmAtmSpvcVccEntry

atmAtmSpvcVccEntry		3.1.1751.2.18.6.33.1
Row definition of ATM SPVC VCC connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmAtmSpvcVccEntry

atmAtmSpvcVccVpiA		3.1.1751.2.18.6.33.1.1
VPI value for side A of an ATM SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmAtmSpvcVccVciA		3.1.1751.2.18.6.33.1.2
VCI value for side A of an ATM SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmAtmSpvcVccRemoteAtmPortAddr		3.1.1751.2.18.6.33.1.3
Remote ATM port NSAP address, not meaningful if passive type of connection.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(1..20)

atmAtmSpvcVccIfB		3.1.1751.2.18.6.33.1.4
Interface index for side B of an ATM SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

atmAtmSpvcVccVpiB		3.1.1751.2.18.6.33.1.5
VPI value for side B of an ATM SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

atmAtmSpvcVccVciB		3.1.1751.2.18.6.33.1.6
VCI value for side B of an ATM SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

atmAtmSpvcVccServiceTypeA2B		3.1.1751.2.18.6.33.1.7
Service type, ATM port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9)

atmAtmSpvcVccSarTypeA2B		3.1.1751.2.18.6.33.1.8
SAR type used in ATM adaption, ATM port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmAtmSpvcVccPeakCellRateA2B		3.1.1751.2.18.6.33.1.9
Peak cell rate - side A, ATM port, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVccSusCellRateA2B		3.1.1751.2.18.6.33.1.10
Sustained cell rate - side A, ATM port, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVccMaxBurstSizeA2B		3.1.1751.2.18.6.33.1.11
Maximum burst size - side A, ATM port, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVccFrwdErrCorrectionA2B		3.1.1751.2.18.6.33.1.12
Forward error correction scheme, ATM port side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4), autoHiQ(5), auto(6), autoLoQ(7)

atmAtmSpvcVccServiceTypeB2A		3.1.1751.2.18.6.33.1.13
Service type, ATM trunk side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9)

atmAtmSpvcVccSarTypeB2A		3.1.1751.2.18.6.33.1.14
SAR type used in ATM adaption, ATM trunk side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmAtmSpvcVccPeakCellRateB2A		3.1.1751.2.18.6.33.1.15
Peak cell rate - side B, ATM trunk, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVccSusCellRateB2A		3.1.1751.2.18.6.33.1.16
Sustained cell rate - side B, ATM trunk, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVccMaxBurstSizeB2A		3.1.1751.2.18.6.33.1.17
Maximum burst size - side A, ATM trunk, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVccFrwdErrCorrectionB2A		3.1.1751.2.18.6.33.1.18
Forward error correction scheme, ATM trunk side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4), autoHiQ(5), auto(6), autoLoQ(7)

atmAtmSpvcVccFlow		3.1.1751.2.18.6.33.1.19
Type of flow, pointToMultipointA2B is for future support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), pointToMultipointA2B(3), simplexB2A(4), pointToMultipointB2A(5)

atmAtmSpvcVccType		3.1.1751.2.18.6.33.1.20
Type of connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nonsecured(1), secured(2)

atmAtmSpvcVccConnType		3.1.1751.2.18.6.33.1.21
The type of connection: activeSvc - attempt calls, whenever not established. passiveSvc - accept calls.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	activeSvc(1), passiveSvc(2)

atmAtmSpvcVccLeafReference		3.1.1751.2.18.6.33.1.22
An arbitrary integer which serves to distinguish the mulitple leaves attached to a root of a point-to-multipoint SPVC. If point-to-point SPVC, the value should be 1.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atmAtmSpvcVccOperStatus		3.1.1751.2.18.6.33.1.23
The operation status of the connection: other - none of the types specified below. establishmentInProgress - connection is not operational, but call attempts are ongoing. connected - connection is currently operational. retriesExhausted - retry limit has been reached and call attempts have ceased. noAddressSupplied - no remote address has been configured, so no call attempts are initiated. lowerLayerDown - SPVC handler is not operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), establishmentInProgress(2), connected(3), retriesExhausted(4), noAddressSupplied(5), lowerLayerDown(6), waitingForCall(7), waitingForRetryTimer(8)

atmAtmSpvcVccRowStatus		3.1.1751.2.18.6.33.1.24
Used to create and delete a soft PVC. When this object is set to 'active', an attempt is made to set up the soft PVC. When this object has the value 'active' and is set to another value, any setup or connection in-progress is released.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

atmAtmSpvcVccRemoteSelectType		3.1.1751.2.18.6.33.1.25
Indicates whether the remote VPI/VCI values are to be used at the destination. If 'any' is used, the destination switch will choose the VPI/VCI values. In such a case, once the SPVC is connected, the value of this object will change to 'required', such that the same VPI/VCI values will continue to be used even if the connection is torn down and re-established. If the value 'required' is specified, the values: atmAtmSpvcVccRemoteVpi and atmAtmSpvcVccRemoteVci, must be supplied and are used at the destination.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	required(1), any(2)

atmAtmSpvcVccRemoteVpi		3.1.1751.2.18.6.33.1.26
VPI value to be used at the destination of an ATM SPVC VCC connection. Valid range is a number between 0 and 4095. If atmAtmSpvcVccRemoteSelectType is configured as 'any', then this value is not relevant.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

atmAtmSpvcVccRemoteVci		3.1.1751.2.18.6.33.1.27
VCI value to be used at the destination of an ATM SPVC VCC connection. Valid range is a number between 0 and 65535. If atmAtmSpvcVccRemoteSelectType is configured as 'any', then this value is not relevant.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmAtmSpvcVccRetryInterval		3.1.1751.2.18.6.33.1.28
The time to wait before attempting to establish the SVC after a previous failed call attempt. A value of 0 indicates retries will be attempted immediately.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

atmAtmSpvcVccRetryLimit		3.1.1751.2.18.6.33.1.29
A maximum limit on how many retries should be attempted. A value of 0 indicates no limit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmAtmSpvcVccRestart		3.1.1751.2.18.6.33.1.30
The active SVC is released, if necessary, and a new setup procedure is begun if 'restart', otherwise, noop.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noop(2)

atmAtmSpvcVccRetryFailure		3.1.1751.2.18.6.33.1.31
Indicates how many attempts to establish the connection have failed. It it reset whenever a connection is successfully established or the SVC is restarted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccReleaseCause		3.1.1751.2.18.6.33.1.32
CAUSE field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..127

atmAtmSpvcVccReleaseDiag		3.1.1751.2.18.6.33.1.33
DIAGNOSTICS field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

atmAtmSpvcVccRelease		3.1.1751.2.18.6.33.1.34
Release the connnection established on the endpoint and if the endpoint is Active, do not retry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	release(1), noop(2)

atmAtmSpvcVccStatsInCellCountHiA		3.1.1751.2.18.6.33.1.35
Valid Cells received on A - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsInCellCountLoA		3.1.1751.2.18.6.33.1.36
Valid Cells received on A - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsOutCellCountHiA		3.1.1751.2.18.6.33.1.37
Valid cells transmitted on A -(High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsOutCellCountLoA		3.1.1751.2.18.6.33.1.38
Valid cells transmitted on A -(Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsInCellCountHiB		3.1.1751.2.18.6.33.1.39
Valid Cells received on B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsInCellCountLoB		3.1.1751.2.18.6.33.1.40
Valid Cells received on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsOutCellCountHiB		3.1.1751.2.18.6.33.1.41
Valid cells transmitted on B -(High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsOutCellCountLoB		3.1.1751.2.18.6.33.1.42
Valid cells transmitted on B -(Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsTimer		3.1.1751.2.18.6.33.1.43
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsFrwdErrCrrctnRateA2B		3.1.1751.2.18.6.33.1.44
Displays the Forward error correction rate being used by the FEC module in the A2B direction. This field is dynamic when Auto rates are selected. In other cases, it will display the rate set by the user.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4)

atmAtmSpvcVccStatsFrwdErrCrrctnRateB2A		3.1.1751.2.18.6.33.1.45
Displays the Forward error correction rate being used by the FEC module in the B2A direction. This field is dynamic when Auto rates are selected. In other cases, it will display the rate set by the user.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4)

atmAtmSpvcVccStatsInOdometerCellCountHiA		3.1.1751.2.18.6.33.1.46
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsInOdometerCellCountLoA		3.1.1751.2.18.6.33.1.47
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsOutOdometerCellCountHiA		3.1.1751.2.18.6.33.1.48
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsOutOdometerCellCountLoA		3.1.1751.2.18.6.33.1.49
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.6.33.1.50
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.6.33.1.51
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.6.33.1.52
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.6.33.1.53
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsOdometerTimer		3.1.1751.2.18.6.33.1.54
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsOdometerReset		3.1.1751.2.18.6.33.1.55
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

atmAtmSpvcVccViA		3.1.1751.2.18.6.33.1.56
VI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmAtmSpvcVccViB		3.1.1751.2.18.6.33.1.57
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmAtmSpvcVccStatsCellsDroppedA		3.1.1751.2.18.6.33.1.58
Cells Dropped on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsCellsTaggedA		3.1.1751.2.18.6.33.1.59
Cells Tagged on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsCellsDroppedB		3.1.1751.2.18.6.33.1.60
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccStatsCellsTaggedB		3.1.1751.2.18.6.33.1.61
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVccVUNIA		3.1.1751.2.18.6.33.1.62
VUNI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmAtmSpvcVccVUNIB		3.1.1751.2.18.6.33.1.63
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmAtmSpvcVccTrafficShapingA2B		3.1.1751.2.18.6.33.1.64
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmAtmSpvcVccTrafficShapingB2A		3.1.1751.2.18.6.33.1.65
Traffic Shaping Support in the B2A direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmAtmSpvcVccPriority		3.1.1751.2.18.6.33.1.66
Priority of SPVC - priority-1 being highest priority .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	priority-1(1), priority-2(2), priority-3(3), priority-4(4)

cirAtmSpvcVccTable		3.1.1751.2.18.6.34
Table of Circuit Emulation to ATM Soft PVCs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirAtmSpvcVccEntry

cirAtmSpvcVccEntry		3.1.1751.2.18.6.34.1
Row definition of circuit emulation to ATM SPVC connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	CirAtmSpvcVccEntry

cirAtmSpvcVccRemoteCePortAddr		3.1.1751.2.18.6.34.1.1
The ATM address supporting the corresponding far end CES IWF process. If no address is supplied, no attempts to establish the active SVC are initiated.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(1..20)

cirAtmSpvcVccIfB		3.1.1751.2.18.6.34.1.2
Interface index for side B, the atm side, of a circuit emulation-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

cirAtmSpvcVccVpiB		3.1.1751.2.18.6.34.1.3
VPI value for side B, the atm side, of a circuit emulation-atm SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

cirAtmSpvcVccVciB		3.1.1751.2.18.6.34.1.4
VCI value for side B, the atm side, of a circuit emulation-atm SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

cirAtmSpvcVccVoiceCompressionA2B		3.1.1751.2.18.6.34.1.5
Voice Compression Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g726-16k(2), g726-24k(3), g726-32k(4), g726-40k(5), g729a-8k(6)

cirAtmSpvcVccSilenceDetectionA2B		3.1.1751.2.18.6.34.1.6
silence detection off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cirAtmSpvcVccEchoCancellationA2B		3.1.1751.2.18.6.34.1.7
Echo Cancellation Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g165-nearEnd(2), g168(3)

cirAtmSpvcVccCngToneDetectionA2B		3.1.1751.2.18.6.34.1.8
Calling Tone Detection Algorithm, one of the enum value, g726-32k(3) is obsoleted on 01Mar99 such that user would not be able to configure CE-ATM
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), bypass(2), g726-32k(3)

cirAtmSpvcVccCodingTranslationA2B		3.1.1751.2.18.6.34.1.9
Coding rule translation type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLaw2muLaw(2), aLaw2aLaw(3), muLaw2aLaw(4), aLaw2muLaw(5)

cirAtmSpvcVccVoiceCompressionB2A		3.1.1751.2.18.6.34.1.10
Voice Compression Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g726-16k(2), g726-24k(3), g726-32k(4), g726-40k(5), g729a-8k(6)

cirAtmSpvcVccSilenceDetectionB2A		3.1.1751.2.18.6.34.1.11
silence detection off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cirAtmSpvcVccEchoCancellationB2A		3.1.1751.2.18.6.34.1.12
Echo Cancellation Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g165-nearEnd(2), g168(3)

cirAtmSpvcVccCngToneDetectionB2A		3.1.1751.2.18.6.34.1.13
Calling Tone Detection Algorithm, one of the enum value, g726-32k(3) is obsoleted on 01Mar99 such that user would not be able to configure CE-ATM
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), bypass(2), g726-32k(3)

cirAtmSpvcVccCodingTranslationB2A		3.1.1751.2.18.6.34.1.14
Coding rule translation type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLaw2muLaw(2), aLaw2aLaw(3), muLaw2aLaw(4), aLaw2muLaw(5)

cirAtmSpvcVccFlow		3.1.1751.2.18.6.34.1.15
Flow Type, pointToMultipointA2B and pointToMultipointB2A are for future support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), simplexB2A(3), pointToMultipointA2B(4), pointToMultipointB2A(5)

cirAtmSpvcVccServiceType		3.1.1751.2.18.6.34.1.16
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cbr-2(2), cbr-3(3), cbr-4(4)

cirAtmSpvcVccConnType		3.1.1751.2.18.6.34.1.17
The type of connection: activeSvc - attempt calls, whenever not established; passiveSvc - accepts calls
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	activeSvc(1), passiveSvc(2)

cirAtmSpvcVccOperStatus		3.1.1751.2.18.6.34.1.18
other - none of the types specified below; establishmentInProgress - connection is not operational, but call attempts are ongoing; connected - connection is currently operational; retriesExhausted - retry limit has been reached and call attempts have ceased; noAddressSupplied - no remote address has been configured, so no call attempts are initiated; lowerLayerDown - SPVC handler is not operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), establishmentInProgress(2), connected(3), retriesExhausted(4), noAddressSupplied(5), lowerLayerDown(6), waitingForCall(7), waitingForRetryTimer(8)

cirAtmSpvcVccRowStatus		3.1.1751.2.18.6.34.1.19
Used to create and delete a soft PVCC. When this object is set to 'active' an attempt is made to set up the soft PVCC. When this object has the value 'active' and is set to another value, any set-up or connection in-progess is released.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

cirAtmSpvcVccViB		3.1.1751.2.18.6.34.1.20
VI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

cirAtmSpvcVccRetryInterval		3.1.1751.2.18.6.34.1.21
The time to wait before attempting to establish the SVC after previous failed call attempt. 0 indicates retries will be attempted immediately.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

cirAtmSpvcVccRetryLimit		3.1.1751.2.18.6.34.1.22
A maximum limit on how many retries. 0 indicates no limit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

cirAtmSpvcVccRestart		3.1.1751.2.18.6.34.1.23
restart, the active SVC is released if necessary and a new setup procedure is begun; or noop
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noop(2)

cirAtmSpvcVccRetryFailure		3.1.1751.2.18.6.34.1.24
Indicates how many attempts to establish the connection have failed. It is reset whenever a connection is successfully established or the SVC is restarted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccReleaseCause		3.1.1751.2.18.6.34.1.25
CAUSE field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..127

cirAtmSpvcVccReleaseDiag		3.1.1751.2.18.6.34.1.26
DIAGNOSTICS field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

cirAtmSpvcVccRelease		3.1.1751.2.18.6.34.1.27
Release the connnection established on the endpoint and if the endpoint is Active, do not retry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	release(1), noop(2)

cirAtmSpvcVccStatsCellsEncodedHiA		3.1.1751.2.18.6.34.1.28
Cells encoded on side A- (High order portion )
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsCellsEncodedLoA		3.1.1751.2.18.6.34.1.29
Cells encoded on side A - ( Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsCellsDecodedHiA		3.1.1751.2.18.6.34.1.30
Cells decoded on side A - ( High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsCellsDecodedLoA		3.1.1751.2.18.6.34.1.31
Cells decoded on side A - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsInCellCountHiB		3.1.1751.2.18.6.34.1.32
Valid Cells received on B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsInCellCountLoB		3.1.1751.2.18.6.34.1.33
Valid Cells received on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsOutCellCountHiB		3.1.1751.2.18.6.34.1.34
Valid cells transmitted on B- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsOutCellCountLoB		3.1.1751.2.18.6.34.1.35
Valid cells transmitted on B -(Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsTimer		3.1.1751.2.18.6.34.1.36
Number of seconds since stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsOdometerCellsEncodedHiA		3.1.1751.2.18.6.34.1.37
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsOdometerCellsEncodedLoA		3.1.1751.2.18.6.34.1.38
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsOdometerCellsDecodedHiA		3.1.1751.2.18.6.34.1.39
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsOdometerCellsDecodedLoA		3.1.1751.2.18.6.34.1.40
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.6.34.1.41
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.6.34.1.42
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.6.34.1.43
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.6.34.1.44
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsOdometerTimer		3.1.1751.2.18.6.34.1.45
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsOdometerReset		3.1.1751.2.18.6.34.1.46
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

cirAtmSpvcVccStatsCellsDroppedB		3.1.1751.2.18.6.34.1.47
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccStatsCellsTaggedB		3.1.1751.2.18.6.34.1.48
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirAtmSpvcVccVUNIB		3.1.1751.2.18.6.34.1.49
VUNI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

cirAtmSpvcVccSarTypeB		3.1.1751.2.18.6.34.1.50
This field will only be used when selecting voice compression, in other cases it will be set to aal1.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal1(1), aal2(2)

cirAtmSpvcVccPriority		3.1.1751.2.18.6.34.1.51
Priority of SPVC - priority-1 being highest priority .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	priority-1(1), priority-2(2), priority-3(3), priority-4(4)

vbrAtmSpvcTable		3.1.1751.2.18.6.35
Table of SPVC atm virtual channel connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrAtmSpvcEntry

vbrAtmSpvcEntry		3.1.1751.2.18.6.35.1
Row definition of atm SPVC VCC connections
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrAtmSpvcEntry

vbrAtmSpvcRemoteVbrPortAddr		3.1.1751.2.18.6.35.1.1
remote VBR port nsap address implemening IWF, not meaningful if passive type of connection
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(1..20)

vbrAtmSpvcIfB		3.1.1751.2.18.6.35.1.2
Interface index for side B, the atm side, of a variable bit rate-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

vbrAtmSpvcVpiB		3.1.1751.2.18.6.35.1.3
VPI value for side B, the atm side, of a variable bit rate-atm SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

vbrAtmSpvcVciB		3.1.1751.2.18.6.35.1.4
VCI value for side B, the atm side, of a variable bit rate-atm SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

vbrAtmSpvcServiceType		3.1.1751.2.18.6.35.1.5
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt1(2), vbr-nrt2(3), vbr-rt1(4), vbr-rt2(5), vbr-express(6)

vbrAtmSpvcPeakCellRateA2B		3.1.1751.2.18.6.35.1.6
peak cell rate - side A, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcSusCellRateA2B		3.1.1751.2.18.6.35.1.7
sustained rate - side A, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcMaxBurstSizeA2B		3.1.1751.2.18.6.35.1.8
maximum burst size - side A, in cells
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcPeakCellRateB2A		3.1.1751.2.18.6.35.1.9
peak rate - side B, ATM trunk, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcSusCellRateB2A		3.1.1751.2.18.6.35.1.10
sustained rate - side B, ATM trunk, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcMaxBurstSizeB2A		3.1.1751.2.18.6.35.1.11
maximum burst size - side B, ATM trunk, in cells.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

vbrAtmSpvcFlow		3.1.1751.2.18.6.35.1.12
type of flow
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), simplexB2A(3)

vbrAtmSpvcConnType		3.1.1751.2.18.6.35.1.13
The type of connection: activeSvc - attempt calls, whenever not established; passiveSvc - accepts calls
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	activeSvc(1), passiveSvc(2)

vbrAtmSpvcOperStatus		3.1.1751.2.18.6.35.1.14
other - none of the types specified below; establishmentInProgress - connection is not operational, but call attempts are ongoing; connected - connection is currently operational; retriesExhausted - retry limit has been reached and call attempts have ceased; noAddressSupplied - no remote address has been configured, so no call attempts are initiated; lowerLayerDown - SPVC handler is not operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), establishmentInProgress(2), connected(3), retriesExhausted(4), noAddressSupplied(5), lowerLayerDown(6), waitingForCall(7), waitingForRetryTimer(8)

vbrAtmSpvcRowStatus		3.1.1751.2.18.6.35.1.15
Used to create and delete a soft PVCC. When this object is set to 'active' an attempt is made to set up the soft PVCC. When this object has the value 'active' and is set to another value, any set-up or connection in-progess is released.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

vbrAtmSpvcViB		3.1.1751.2.18.6.35.1.16
VI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

vbrAtmSpvcRetryInterval		3.1.1751.2.18.6.35.1.17
the time to wait before attempting to establish the SVC after previous failed call attempt. 0 indicates retries will be attempted immediately.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

vbrAtmSpvcRetryLimit		3.1.1751.2.18.6.35.1.18
a maximum limit on how many retries. 0 indicates no limit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

vbrAtmSpvcRestart		3.1.1751.2.18.6.35.1.19
restart, the active SVC is released if necessary and a new setup procedure is begun; or noop
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noop(2)

vbrAtmSpvcRetryFailure		3.1.1751.2.18.6.35.1.20
indicates how many attempts to establish the connection have failed. It is reset whenever a connection is successfully established or the SVC is restarted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcReleaseCause		3.1.1751.2.18.6.35.1.21
CAUSE field value of the last RELEASE message received for this SVC
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..127

vbrAtmSpvcReleaseDiag		3.1.1751.2.18.6.35.1.22
DIAGNOSTICS field value of the last RELEASE message received for this SVC
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

vbrAtmSpvcRelease		3.1.1751.2.18.6.35.1.23
Release the connnection established on the endpoint and if the endpoint is Active, do not retry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	release(1), noop(2)

vbrAtmSpvcStatsCellsEncodedHiA		3.1.1751.2.18.6.35.1.24
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsCellsEncodedLoA		3.1.1751.2.18.6.35.1.25
ells encoded on side A - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsCellsDecodedHiA		3.1.1751.2.18.6.35.1.26
Cells decoded on side A - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsCellsDecodedLoA		3.1.1751.2.18.6.35.1.27
Cells decoded on side A - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsInCellCountHiB		3.1.1751.2.18.6.35.1.28
Valid Cells received on B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsInCellCountLoB		3.1.1751.2.18.6.35.1.29
Valid Cells received on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsOutCellCountHiB		3.1.1751.2.18.6.35.1.30
Valid cells transmitted on B -(High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsOutCellCountLoB		3.1.1751.2.18.6.35.1.31
Valid cells transmitted on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsTimer		3.1.1751.2.18.6.35.1.32
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsOdometerCellsEncodedHiA		3.1.1751.2.18.6.35.1.33
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsOdometerCellsEncodedLoA		3.1.1751.2.18.6.35.1.34
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsOdometerCellsDecodedHiA		3.1.1751.2.18.6.35.1.35
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsOdometerCellsDecodedLoA		3.1.1751.2.18.6.35.1.36
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsInOdometerCellCountHiB		3.1.1751.2.18.6.35.1.37
Valid Cells received on B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsInOdometerCellCountLoB		3.1.1751.2.18.6.35.1.38
Valid Cells received on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsOutOdometerCellCountHiB		3.1.1751.2.18.6.35.1.39
Valid Cells transmitted on B -(High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsOutOdometerCellCountLoB		3.1.1751.2.18.6.35.1.40
Valid Cells transmitted on B -(Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsOdometerTimer		3.1.1751.2.18.6.35.1.41
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsOdometerReset		3.1.1751.2.18.6.35.1.42
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

vbrAtmSpvcStatsCellsDroppedB		3.1.1751.2.18.6.35.1.43
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcStatsCellsTaggedB		3.1.1751.2.18.6.35.1.44
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVUNIB		3.1.1751.2.18.6.35.1.45
VUNI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

vbrAtmSpvcTrafficShapingA2B		3.1.1751.2.18.6.35.1.46
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

vbrAtmSpvcPriority		3.1.1751.2.18.6.35.1.47
Priority of SPVC - priority-1 being highest priority .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	priority-1(1), priority-2(2), priority-3(3), priority-4(4)

aal2TrunkConfigTable		3.1.1751.2.18.6.36
Table of terminal emulation to ATM network IWF connections
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Aal2TrunkConfigEntry

aal2TrunkConfigEntry		3.1.1751.2.18.6.36.1
Row definition of terminal emulation to ATM network IWF connections
Status: current	Access: not-accessible
OBJECT-TYPE
	Aal2TrunkConfigEntry

aal2TrunkConfigIf		3.1.1751.2.18.6.36.1.1
Interface Id of the Atm Side of the Aal2 Trunk.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

aal2TrunkConfigVpi		3.1.1751.2.18.6.36.1.2
VPI value for Atm side , the atm side, of a atm trunk connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

aal2TrunkConfigVci		3.1.1751.2.18.6.36.1.3
VCI value for the atm side, of a variable bit rate-atm PVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

aal2TrunkConfigServiceType		3.1.1751.2.18.6.36.1.4
Service/Queue types supported for Aal2 Trunk connections.When using Vbr/Ubr type service type oversubscription will have to be taken into account for which nature of traffic going over the Trunk should be known before hand
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cbr-1(1), cbr-2(2), cbr-3(3), cbr-4(4), ubr(5), vbr-nrt2(6), vbr-nrt1(7), vbr-rt2(8), vbr-rt1(9), vbr-express(10)

aal2TrunkConfigPeakCellRateIgr		3.1.1751.2.18.6.36.1.5
peak cell rate - atm side inp, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

aal2TrunkConfigSusCellRateIgr		3.1.1751.2.18.6.36.1.6
sustained rate - atm side inp, in cell per second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

aal2TrunkConfigMaxBurstSizeIgr		3.1.1751.2.18.6.36.1.7
maximum burst size - atm side inp, in cells
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

aal2TrunkConfigPeakCellRateEgr		3.1.1751.2.18.6.36.1.8
peak rate - atm side output, in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

aal2TrunkConfigSusCellRateEgr		3.1.1751.2.18.6.36.1.9
sustained rate - atm side output,in cell per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

aal2TrunkConfigMaxBurstSizeEgr		3.1.1751.2.18.6.36.1.10
maximum burst size - atm side output, in cells.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

aal2TrunkConfigFlow		3.1.1751.2.18.6.36.1.11
Flow type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1)

aal2TrunkConfigRowStatus		3.1.1751.2.18.6.36.1.12
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

aal2TrunkConfigConnectionStatus		3.1.1751.2.18.6.36.1.13
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated . InactiveA2B-B2A: Both the A2B and B2A resource interfaces are not in service. InactiveA2B: The A2B resource interface is not in service. InactiveB2A: The B2A resource interface is not in service. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), inactiveA2B-B2A(3), inactiveA2B(4), inactiveB2A(5)

aal2TrunkConfigViB		3.1.1751.2.18.6.36.1.14
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

aal2TrunkConfigCnfrmTypeB2A		3.1.1751.2.18.6.36.1.15
The following is the description of this field This will be used in conjunction with the service type field to get the correct traffic behaviour. In the conformances the the 0 or 0plus1 refers to the clp bit in the cells. If 0plus1 is the bucket reference then the clp bit is ignored. If 0 is specified for the bucket then check only clp=0 cells. 1: Best Effort will try to send all cellsin a best effort way. This will follow the Aqueman Algorithm 2: one-bucket-notag-0plus1 will use 1 bucket i.e is the PCR(0+1) bucket and drop all cells in excess. 3: two-bucket-notag-0plus1-0plus1 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0+1). All cells conforming to both buckets will be passed through. The rest will be dropped. 4: two-bucket-notag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which conform to both buckets are passed through. The rest are dropped. 5: two-bucket-tag-0plus1-0 uses 2 buckets. The 2 buckets are pcr(0+1) and scr(0) or pcr(0). Cells which do not conform to the first bucket are dropped. Cells which do not conform to the 2nd bucket are tagged. 6: best-effort-tag. Tag all cells and then do a best effort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	best-effort(1), one-bucket-notag-0plus1(2), two-bucket-notag-0plus1-0plus1(3), two-bucket-notag-0plus1-0(4), two-bucket-tag-0plus1-0(5), best-effort-tag(6)

aal2TrunkConfigVUNIB		3.1.1751.2.18.6.36.1.16
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

aal2TrunkAvailBwIgr		3.1.1751.2.18.6.36.1.17
The Avail Bandwidth for that interface in cells per sec.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aal2TrunkAvailBwEgr		3.1.1751.2.18.6.36.1.18
The Avail Bandwidth for that interface in cells per sec.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aal2TrunkGR303		3.1.1751.2.18.6.36.1.19
This flag is used to check if a GR303 Feature is enabled for the trunk.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

aal2TrunkConfigOamStatus		3.1.1751.2.18.6.36.1.20
Indicates the OAM monitoring status of side A. The 2 possible states are: Unsupp: No monitoring enabled. End-Pt: Atm side is only an end point, therefore it will respond to AIS/RDI. End-Seg-Pt: A side is both an end point and a segment point.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), end-Seg-Pt(3)

aal2TrunkConnFailureCauseB		3.1.1751.2.18.6.36.1.21
connection status reason code
Status: current	Access: read-only
OBJECT-TYPE
	AtmConnFailureCause

aal2TrunkCuTimer		3.1.1751.2.18.6.36.1.22
CuTimer represents 'combined use timer', is set to zero such that every ATM cell transmitted contains one, and only one, AAL2 packet, and the first octet of the AAL2 packet header follows immediately after the Start Field in the ATM cell payload. If the AAL2 packet payload is less than 44 octets, the remainder of the ATM cell payload following the end of the AAL2 packet shall be filled with zeros as padding. Each increment of CuTimer means 5ms more to wait. And cuTimer default value 4 means to wait 20ms before the ATM cell is sent out.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..8

gr303Aal2PvcVccTable		3.1.1751.2.18.6.37
Table of Gr303 to AAL2 Cid monitor VCCs
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Gr303Aal2PvcVccEntry

gr303Aal2PvcVccEntry		3.1.1751.2.18.6.37.1
Row definition of circuit emulation to atm connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	Gr303Aal2PvcVccEntry

gr303Aal2PvcVccGr303IgId		3.1.1751.2.18.6.37.1.1
GR303 interface group id on the GR303 side of the connection
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..84

gr303Aal2PvcVccGr303CallRef		3.1.1751.2.18.6.37.1.2
The call reference value to be used in the signaling packets on the GR303 interface for the connection on the AAL2CID corresponding to this connection
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..2048

gr303Aal2PvcVccIfB		3.1.1751.2.18.6.37.1.3
Interface index for side B, the atm side, of a circuit emulation-atm PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

gr303Aal2PvcVccVpiB		3.1.1751.2.18.6.37.1.4
VPI value for side B, the atm side, of a circuit emulation-atm PVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

gr303Aal2PvcVccVciB		3.1.1751.2.18.6.37.1.5
VCI value for side B, the atm side, of a circuit emulation-atm PVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

gr303Aal2PvcVccAal2Cid		3.1.1751.2.18.6.37.1.6
Aal2 Cid Used to pack ce chan in an Atm Trunk. This value will be unique per Atm Trunk. This field will be applicable when Aal type is chosen to be Standard Aal2.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..255

gr303Aal2PvcVccRowStatus		3.1.1751.2.18.6.37.1.7
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

gr303Aal2PvcVccVoiceEncodingProfile		3.1.1751.2.18.6.37.1.8
Profile for use by voice/voiceband data. Profile-3 and Profile-7 are ITU-T predefined profiles which specify the voice compression and silence removal algorithms. If custom profile is chosen all DSP specific parameters have to be specified by the user. If default profile is chosen all parameters on the AAL2 trunk, containing this CID, will be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	itut-profile-1(1), itut-profile-3(3), af-profile-6(6), itut-profile-7(7), af-profile-7(8), af-profile-8(9), af-profile-9(10), af-profile-10(11), af-profile-12(12), custom(256), default(257)

gr303Aal2PvcVccVoiceCompression		3.1.1751.2.18.6.37.1.9
Voice Compression Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g726-16k(2), g726-24k(3), g726-32k(4), g726-40k(5), g729a-8k(6)

gr303Aal2PvcVccSilenceDetection		3.1.1751.2.18.6.37.1.10
silence detection off/on
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

gr303Aal2PvcVccEchoCancellation		3.1.1751.2.18.6.37.1.11
Echo Cancellation Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), g165-nearEnd(2), g168(3)

gr303Aal2PvcVccCngToneDetection		3.1.1751.2.18.6.37.1.12
Calling Tone Detection Algorithm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), bypass(2)

gr303Aal2PvcVccCodingTranslation		3.1.1751.2.18.6.37.1.13
Coding rule translation type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), muLaw2muLaw(2), aLaw2aLaw(3), muLaw2aLaw(4), aLaw2muLaw(5)

gr303Aal2PvcVccConnectionStatus		3.1.1751.2.18.6.37.1.14
Indicates the current connections status. Active: All interfaces through which the connection is going are in service. Inactive: One of the end interfaces of the connection is not in service. The rest of the states apply to connections going through resource interfaces like DSP2 and FEC. These interfaces are dynamically allocated. If an end interface and the resource interfaces are out of service, the status will be inactive because the end interfaces take priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2)

gr303Aal2PvcVccAltLineType		3.1.1751.2.18.6.37.1.15
Analog Line Termination Line Type on the subscriber side. The ABCD bit codes for diffterent signal types depend on the analog line type. The analog type can be overwritten by an EOC message from the IDT
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	alt-LoopReverseBattery(1), alt-groundStart(9), alt-loopStart(13), alt-winkStart(29)

atmAtmSpvcVpcTable		3.1.1751.2.18.6.38
Table of SPVC ATM virtual path connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmAtmSpvcVpcEntry

atmAtmSpvcVpcEntry		3.1.1751.2.18.6.38.1
Row definition of ATM SPVC VPC connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmAtmSpvcVpcEntry

atmAtmSpvcVpcVpiA		3.1.1751.2.18.6.38.1.1
VPI value for side A of an ATM SPVC VPC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmAtmSpvcVpcRemoteAtmPortAddr		3.1.1751.2.18.6.38.1.2
Remote ATM port NSAP address, not meaningful if passive type of connection.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(1..20)

atmAtmSpvcVpcIfB		3.1.1751.2.18.6.38.1.3
Interface index for side B of an ATM SPVC VPC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the path number.
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

atmAtmSpvcVpcVpiB		3.1.1751.2.18.6.38.1.4
VPI value for side B of an ATM SPVC VPC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

atmAtmSpvcVpcServiceTypeA2B		3.1.1751.2.18.6.38.1.5
Service type, ATM port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9)

atmAtmSpvcVpcSarTypeA2B		3.1.1751.2.18.6.38.1.6
SAR type used in ATM adaption, ATM port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmAtmSpvcVpcPeakCellRateA2B		3.1.1751.2.18.6.38.1.7
Peak cell rate - side A, ATM port, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcSusCellRateA2B		3.1.1751.2.18.6.38.1.8
Sustained cell rate - side A, ATM port, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcMaxBurstSizeA2B		3.1.1751.2.18.6.38.1.9
Maximum burst size - side A, ATM port, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcFrwdErrCorrectionA2B		3.1.1751.2.18.6.38.1.10
Forward error correction scheme, ATM port side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4), autoHiQ(5), auto(6), autoLoQ(7)

atmAtmSpvcVpcServiceTypeB2A		3.1.1751.2.18.6.38.1.11
Service type, ATM trunk side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9)

atmAtmSpvcVpcSarTypeB2A		3.1.1751.2.18.6.38.1.12
SAR type used in ATM adaption, ATM trunk side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aal5(1), aal3-4(2), aal2(3), aal1(4), null(5)

atmAtmSpvcVpcPeakCellRateB2A		3.1.1751.2.18.6.38.1.13
Peak cell rate - side B, ATM trunk, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcSusCellRateB2A		3.1.1751.2.18.6.38.1.14
Sustained cell rate - side B, ATM trunk, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcMaxBurstSizeB2A		3.1.1751.2.18.6.38.1.15
Maximum burst size - side A, ATM trunk, in cells per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcFrwdErrCorrectionB2A		3.1.1751.2.18.6.38.1.16
Forward error correction scheme, ATM trunk side.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4), autoHiQ(5), auto(6), autoLoQ(7)

atmAtmSpvcVpcFlow		3.1.1751.2.18.6.38.1.17
Type of flow, pointToMultipointA2B is for future support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1), simplexA2B(2), pointToMultipointA2B(3), simplexB2A(4), pointToMultipointB2A(5)

atmAtmSpvcVpcType		3.1.1751.2.18.6.38.1.18
Type of connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nonsecured(1), secured(2)

atmAtmSpvcVpcConnType		3.1.1751.2.18.6.38.1.19
The type of connection: activeSvc - attempt calls, whenever not established. passiveSvc - accept calls.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	activeSvc(1), passiveSvc(2)

atmAtmSpvcVpcLeafReference		3.1.1751.2.18.6.38.1.20
An arbitrary integer which serves to distinguish the mulitple leaves attached to a root of a point-to-multipoint SPVC. If point-to-point SPVC, the value should be 1.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atmAtmSpvcVpcOperStatus		3.1.1751.2.18.6.38.1.21
The operation status of the connection: other - none of the types specified below. establishmentInProgress - connection is not operational, but call attempts are ongoing. connected - connection is currently operational. retriesExhausted - retry limit has been reached and call attempts have ceased. noAddressSupplied - no remote address has been configured, so no call attempts are initiated. lowerLayerDown - SPVC handler is not operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), establishmentInProgress(2), connected(3), retriesExhausted(4), noAddressSupplied(5), lowerLayerDown(6), waitingForCall(7), waitingForRetryTimer(8)

atmAtmSpvcVpcRowStatus		3.1.1751.2.18.6.38.1.22
Used to create and delete a soft PVC. When this object is set to 'active', an attempt is made to set up the soft PVC. When this object has the value 'active' and is set to another value, any setup or connection in-progress is released.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

atmAtmSpvcVpcRemoteSelectType		3.1.1751.2.18.6.38.1.23
Indicates whether the remote VPI values are to be used at the destination. If 'any' is used, the destination switch will choose the VPI values. In such a case, once the SPVC is connected, the value of this object will change to 'required', such that the same VPI values will continue to be used even if the connection is torn down and re-established. If the value 'required' is specified, the values: atmAtmSpvcVpcRemoteVpi and must be supplied and are used at the destination.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	required(1), any(2)

atmAtmSpvcVpcRemoteVpi		3.1.1751.2.18.6.38.1.24
VPI value to be used at the destination of an ATM SPVC VPC connection. Valid range is a number between 0 and 4095. If atmAtmSpvcVpcRemoteSelectType is configured as 'any', then this value is not relevant.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

atmAtmSpvcVpcRetryInterval		3.1.1751.2.18.6.38.1.25
The time to wait before attempting to establish the SVC after a previous failed call attempt. A value of 0 indicates retries will be attempted immediately.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

atmAtmSpvcVpcRetryLimit		3.1.1751.2.18.6.38.1.26
A maximum limit on how many retries should be attempted. A value of 0 indicates no limit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atmAtmSpvcVpcRestart		3.1.1751.2.18.6.38.1.27
The active SVC is released, if necessary, and a new setup procedure is begun if 'restart', otherwise, noop.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noop(2)

atmAtmSpvcVpcRetryFailure		3.1.1751.2.18.6.38.1.28
Indicates how many attempts to establish the connection have failed. It it reset whenever a connection is successfully established or the SVC is restarted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcReleaseCause		3.1.1751.2.18.6.38.1.29
CAUSE field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..127

atmAtmSpvcVpcReleaseDiag		3.1.1751.2.18.6.38.1.30
DIAGNOSTICS field value of the last RELEASE message received for this SVC.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..8)

atmAtmSpvcVpcRelease		3.1.1751.2.18.6.38.1.31
Release the connnection established on the endpoint and if the endpoint is Active, do not retry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	release(1), noop(2)

atmAtmSpvcVpcStatsInCellCountHiA		3.1.1751.2.18.6.38.1.32
Valid Cells received on A - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsInCellCountLoA		3.1.1751.2.18.6.38.1.33
Valid Cells received on A - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsOutCellCountHiA		3.1.1751.2.18.6.38.1.34
Valid cells transmitted on A -(High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsOutCellCountLoA		3.1.1751.2.18.6.38.1.35
Valid cells transmitted on A -(Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsInCellCountHiB		3.1.1751.2.18.6.38.1.36
Valid Cells received on B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsInCellCountLoB		3.1.1751.2.18.6.38.1.37
Valid Cells received on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsOutCellCountHiB		3.1.1751.2.18.6.38.1.38
Valid cells transmitted on B -(High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsOutCellCountLoB		3.1.1751.2.18.6.38.1.39
Valid cells transmitted on B -(Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsTimer		3.1.1751.2.18.6.38.1.40
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsFrwdErrCrrctnRateA2B		3.1.1751.2.18.6.38.1.41
Displays the Forward error correction rate being used by the FEC module in the A2B direction. This field is dynamic when Auto rates are selected. In other cases, it will display the rate set by the user.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4)

atmAtmSpvcVpcStatsFrwdErrCrrctnRateB2A		3.1.1751.2.18.6.38.1.42
Displays the Forward error correction rate being used by the FEC module in the B2A direction. This field is dynamic when Auto rates are selected. In other cases, it will display the rate set by the user.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4)

atmAtmSpvcVpcStatsInOdometerCellCountHiA		3.1.1751.2.18.6.38.1.43
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsInOdometerCellCountLoA		3.1.1751.2.18.6.38.1.44
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsOutOdometerCellCountHiA		3.1.1751.2.18.6.38.1.45
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsOutOdometerCellCountLoA		3.1.1751.2.18.6.38.1.46
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsInOdometerCellCountHiB		3.1.1751.2.18.6.38.1.47
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsInOdometerCellCountLoB		3.1.1751.2.18.6.38.1.48
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsOutOdometerCellCountHiB		3.1.1751.2.18.6.38.1.49
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsOutOdometerCellCountLoB		3.1.1751.2.18.6.38.1.50
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsOdometerTimer		3.1.1751.2.18.6.38.1.51
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsOdometerReset		3.1.1751.2.18.6.38.1.52
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

atmAtmSpvcVpcViA		3.1.1751.2.18.6.38.1.53
VI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmAtmSpvcVpcViB		3.1.1751.2.18.6.38.1.54
VI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

atmAtmSpvcVpcStatsCellsDroppedA		3.1.1751.2.18.6.38.1.55
Cells Dropped on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsCellsTaggedA		3.1.1751.2.18.6.38.1.56
Cells Tagged on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsCellsDroppedB		3.1.1751.2.18.6.38.1.57
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcStatsCellsTaggedB		3.1.1751.2.18.6.38.1.58
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAtmSpvcVpcVUNIA		3.1.1751.2.18.6.38.1.59
VUNI to associate the Egress part of the B2A connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmAtmSpvcVpcVUNIB		3.1.1751.2.18.6.38.1.60
VUNI to associate the Egress part of the A2B connection .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atmAtmSpvcVpcTrafficShapingA2B		3.1.1751.2.18.6.38.1.61
Traffic Shaping Support in the A2B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmAtmSpvcVpcTrafficShapingB2A		3.1.1751.2.18.6.38.1.62
Traffic Shaping Support in the B2A direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmAtmSpvcVpcPriority		3.1.1751.2.18.6.38.1.63
Priority of SPVC - priority-1 being highest priority .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	priority-1(1), priority-2(2), priority-3(3), priority-4(4)

intfAtmPvcConnDisplayTable		3.1.1751.2.18.6.39
List of Pvc Connections on an Interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IntfAtmConnDisplayEntry

intfAtmPvcConnDisplayEntry		3.1.1751.2.18.6.39.1
Gives list of pvc going towards the backplane on a particluar interface
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfAtmConnDisplayEntry

intfAtmPvcConnDisplaySlot		3.1.1751.2.18.6.39.1.1
Slot of the particular interface
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

intfAtmPvcConnDisplayPort		3.1.1751.2.18.6.39.1.2
Port of the particular interface
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

intfAtmPvcConnDisplayChannel		3.1.1751.2.18.6.39.1.3
Channel of the particular interface
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

intfAtmPvcConnDisplayVpi		3.1.1751.2.18.6.39.1.4
VPI value for connection on Intf Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

intfAtmPvcConnDisplayVci		3.1.1751.2.18.6.39.1.5
VCI value for connection on Intf Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

intfAtmPvcConnDisplayFlowType		3.1.1751.2.18.6.39.1.6
Flow type:Indicates Flow Towards the Back Plane cnctnValid: Traffic flow towards BP is enabled. cnctnNull: Traffic flow towards BP is disabled. cnctnPtmpValid: Traffic flow towards BP is enabled and it is point to multipoint connection. cnctnPtmpNull: Traffic flow towards BP is disabled and it is point to multipoint connection.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cnctnValid(1), cnctnNull(2), cnctnPtmpValid(3), cnctnPtmpNull(4)

ds3PortStatsTable		3.1.1751.2.18.10.1
Table of statisics for a DS3 port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ds3PortStatsEntry

ds3PortStatsEntry		3.1.1751.2.18.10.1.1
Row definition for the DS3 port statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	Ds3PortStatsEntry

ds3PortStatsId		3.1.1751.2.18.10.1.1.1
Port ID - Slot/Port (SSPP)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ds3PortStatsTimer		3.1.1751.2.18.10.1.1.2
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ds3PortStatsCurrentSEFSs		3.1.1751.2.18.10.1.1.3
severely errored framing seconds
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ds3PortStatsCurrentLCVs		3.1.1751.2.18.10.1.1.4
Line coding violations encountered
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ds3PortStatsCurrentLESs		3.1.1751.2.18.10.1.1.5
Line errored seconds
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ds1PortStatsTable		3.1.1751.2.18.10.2
Table of statisics for a DS1 port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ds1PortStatsEntry

ds1PortStatsEntry		3.1.1751.2.18.10.2.1
Row definition for the DS1 port statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	Ds1PortStatsEntry

ds1PortStatsId		3.1.1751.2.18.10.2.1.1
Port ID - Slot/Port (SSPP)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ds1PortStatsTimer		3.1.1751.2.18.10.2.1.2
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ds1PortStatsCurrentESs		3.1.1751.2.18.10.2.1.3
The number of Errored Seconds, encountered by a DS1 interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ds1PortStatsCurrentSESs		3.1.1751.2.18.10.2.1.4
The number of Severely Errored Seconds encoun- tered by a DS1 interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ds1PortStatsCurrentLCVs		3.1.1751.2.18.10.2.1.5
The number of Line Code Violations (LCVs) en- countered by a DS1 interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3PortStatsTable		3.1.1751.2.18.10.3
Table of statisics for a OC3 port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Oc3PortStatsEntry

oc3PortStatsEntry		3.1.1751.2.18.10.3.1
Row definition for the OC3 port statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	Oc3PortStatsEntry

oc3PortStatsId		3.1.1751.2.18.10.3.1.1
Port ID - Slot/Port (SSPP)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

oc3PortStatsSectionBip8Errs		3.1.1751.2.18.10.3.1.2
section sublayer BIP8 errors.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3PortStatsLineBip8Errs		3.1.1751.2.18.10.3.1.3
line sublayer BIP8 errors.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3PortStatsPathBip8Errs		3.1.1751.2.18.10.3.1.4
path sublayer BIP8 errors.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3PortStatsLineFebeCount		3.1.1751.2.18.10.3.1.5
line sublayer FEBE count.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3PortStatsPathFebeCount		3.1.1751.2.18.10.3.1.6
path sublayer FEBE count.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3PortStatsTimer		3.1.1751.2.18.10.3.1.7
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

msPortStatsTable		3.1.1751.2.18.10.4
Table of statisics for a MS port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MsPortStatsEntry

msPortStatsEntry		3.1.1751.2.18.10.4.1
Row definition for the MS port statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	MsPortStatsEntry

msPortStatsId		3.1.1751.2.18.10.4.1.1
Port ID - Slot/Port (SSPP)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

msPortStatsFrameErrors		3.1.1751.2.18.10.4.1.4
P-bit severely errored seconds
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

msPortStatsOutOfFrameSeconds		3.1.1751.2.18.10.4.1.5
severely errored framing seconds
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

msPortStatsTimer		3.1.1751.2.18.10.4.1.6
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

e3PortStatsTable		3.1.1751.2.18.10.5
Table of statisics for a E3 port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		E3PortStatsEntry

e3PortStatsEntry		3.1.1751.2.18.10.5.1
Row definition for the E3 port statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	E3PortStatsEntry

e3PortStatsId		3.1.1751.2.18.10.5.1.1
Port ID - Slot/Port (SSPP)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

e3PortStatsTimer		3.1.1751.2.18.10.5.1.2
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

e3PortStatsCurrentSEFSs		3.1.1751.2.18.10.5.1.3
severely errored framing seconds
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

e3PortStatsCurrentLCVs		3.1.1751.2.18.10.5.1.4
Line coding violations encountered
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

e3PortStatsCurrentLESs		3.1.1751.2.18.10.5.1.5
Line errored seconds
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

e1PortStatsTable		3.1.1751.2.18.10.6
Table of statisics for a E1 port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		E1PortStatsEntry

e1PortStatsEntry		3.1.1751.2.18.10.6.1
Row definition for the E1 port statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	E1PortStatsEntry

e1PortStatsId		3.1.1751.2.18.10.6.1.1
Port ID - Slot/Port (SSPP)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

e1PortStatsTimer		3.1.1751.2.18.10.6.1.2
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

e1PortStatsCurrentESs		3.1.1751.2.18.10.6.1.3
The number of Errored Seconds, encountered by a E1 interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

e1PortStatsCurrentSESs		3.1.1751.2.18.10.6.1.4
The number of Severely Errored Seconds encoun- tered by a E1 interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

e1PortStatsCurrentLCVs		3.1.1751.2.18.10.6.1.5
The number of Line Code Violations (LCVs) en- countered by a E1 interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsTable		3.1.1751.2.18.10.7
Statisics for a collection of ethernet-like interfaces attached to a particular system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthernetPortStatsEntry

ethernetPortStatsEntry		3.1.1751.2.18.10.7.1
Statistics for a particular interface to an ethernet-like medium.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthernetPortStatsEntry

ethernetPortStatsId		3.1.1751.2.18.10.7.1.1
An index value that uniquely identifies an interface to an ethernet-like medium. The interface identified by a particular value of this index is the same interface as identified by the same value of ethernetPortId.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ethernetPortStatsTimer		3.1.1751.2.18.10.7.1.2
Time, in seconds, since last reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsAlignmentErrors		3.1.1751.2.18.10.7.1.3
A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsFCSErrors		3.1.1751.2.18.10.7.1.4
A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsSingleCollisionFrames		3.1.1751.2.18.10.7.1.5
A count of successfully transmitted frames on a particular interface for which trnasmission is inhibited by exactly one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, IfOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the ethernetPortStatsMulitipleCollisionFrames object.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsMultipleCollisionFrames		3.1.1751.2.18.10.7.1.6
A count of successfully transmitted frames on a particular interface for which trnasmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, IfOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the ethernetPortStatsSingleCollisionFrames object.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsSQETestErrors		3.1.1751.2.18.10.7.1.7
A count of times that the SQE TEST ERROR message is generated by the PLS sublayer for a particular interface. The SQE TEST ERROR message is defined in section 7.2.2.2.4 of ANSI/IEEE 802.3-1985 and its generation is described in section 7.2.4.6 of the same document.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsDeferredTransmissions		3.1.1751.2.18.10.7.1.8
A count of frames for which the first transmission attempt on a particluar interface is delayed because the medium is busy. the count represented by an instance of this object does not include frames involved in collisions.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsLateCollisions		3.1.1751.2.18.10.7.1.9
The number of times that a collision is detected on a particular interface later than 512 bit-times into the transmission of a packet. Five hundred and twelve bit-times corresponds to 51.2 microseconds on a 10 Mbit/s system. A (late) collision included in a count represented by an instance of this object is also considered as a (generic) collision for purposes of other collision-related statistics.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsExcessiveCollisions		3.1.1751.2.18.10.7.1.10
A count of frames for which transmission on a particular interface fails due to excessive collisions.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsInternalMacTransmitErrors		3.1.1751.2.18.10.7.1.11
A count of frames for which transmission on a particular interface fails due to an internal MAC sublayer transmit error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the ethernetPortStatsLateCollisions object, the ethernetPortStatsExcessiveCollisions object, or the ethernetPortStatsCarrierSenseErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of transmission errors on a particular interface that are not otherwise counted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsCarrierSenseErrors		3.1.1751.2.18.10.7.1.12
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular interface. The count represented by an instance of this object is incremented at most once per transmission attempt, even if the carrier sense condition fluctuates during a transmission attempt.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsFrameTooLongs		3.1.1751.2.18.10.7.1.13
A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethernetPortStatsInternalMacReceiveErrors		3.1.1751.2.18.10.7.1.14
A count of frames for which reception on a particular interface fails due to an internal MAC sublayer receive error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the ethernetPortStatsFrameTooLongs object, the ethernetPortStatsAlignmentErrors object, or the ethernetPortStatsFCSErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of receive errors on a particular interface that are not otherwise counted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIfStatsTable		3.1.1751.2.18.11.1
Table of statistics for an atmUni interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmIfStatsEntry

atmIfStatsEntry		3.1.1751.2.18.11.1.1
Row definition for the atmUni statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmIfStatsEntry

atmIfStatsId		3.1.1751.2.18.11.1.1.1
Interface index (SSPPCCC) to the atmUni statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmIfStatsValidCellsInHi		3.1.1751.2.18.11.1.1.2
Number of valid cells received on the channel - High Word
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIfStatsValidCellsInLo		3.1.1751.2.18.11.1.1.3
Number of valid cells received on the channel - low Word
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIfStatsErroredCellsIn		3.1.1751.2.18.11.1.1.4
Number of errored cells received on the channel
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIfStatsMismatchedCellsIn		3.1.1751.2.18.11.1.1.5
Number of Vpi/Vci translation errors on input cells.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIfStatsNullCellsOutHi		3.1.1751.2.18.11.1.1.6
Number of null cells sent out on the channel - High Word
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIfStatsNullCellsOutLo		3.1.1751.2.18.11.1.1.7
Number of null cells sent out on the channel - Low Word
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIfStatsValidCellsOutHi		3.1.1751.2.18.11.1.1.8
Number of valid cells sent out on the channel - High Word
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIfStatsValidCellsOutLo		3.1.1751.2.18.11.1.1.9
Number of valid cells sent out on the channel - Low Word
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmIfStatsTimer		3.1.1751.2.18.11.1.1.10
Time, in seconds, since last reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..899

frUniStatsTable		3.1.1751.2.18.11.2
Table of statistics for a Frame Relay UNI Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrUniStatsEntry

frUniStatsEntry		3.1.1751.2.18.11.2.1
Row definition for the Frame Realy UNI statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	FrUniStatsEntry

frUniStatsId		3.1.1751.2.18.11.2.1.1
Interface index (SSPPCCC) to the frame relay UNI statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frUniStatsTimer		3.1.1751.2.18.11.2.1.9
Time, in seconds, since last reset.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..899

frUniStatsCellsMismatched		3.1.1751.2.18.11.2.1.10
number of cells not matched to provisioned DLCIs.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frUniStatsErroredFrames		3.1.1751.2.18.11.2.1.11
number of errored frames.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frUniStatsCellsEncodedHi		3.1.1751.2.18.11.2.1.12
number of cells encoded - (High order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frUniStatsCellsEncodedLo		3.1.1751.2.18.11.2.1.13
number of cells encoded - (Low order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frUniStatsFramesEncodedHi		3.1.1751.2.18.11.2.1.14
number of frames encoded - (High order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frUniStatsFramesEncodedLo		3.1.1751.2.18.11.2.1.15
number of frames encoded - (Low order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frUniStatsCellsDecodedHi		3.1.1751.2.18.11.2.1.16
number of cells decoded - (High order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frUniStatsCellsDecodedLo		3.1.1751.2.18.11.2.1.17
number of cells decoded - (Low order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frUniStatsFramesDecodedHi		3.1.1751.2.18.11.2.1.18
number of frames decoded - (High order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frUniStatsFramesDecodedLo		3.1.1751.2.18.11.2.1.19
number of frames decoded - (Low order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frUniStatsAAL5Errors		3.1.1751.2.18.11.2.1.20
number of aal5 PDUs with invalid byte count or CRC-32.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmIfStatsTable		3.1.1751.2.18.11.3
Table of statistics for an cirEm interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirEmIfStatsEntry

cirEmIfStatsEntry		3.1.1751.2.18.11.3.1
Row definition for the cirEm statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	CirEmIfStatsEntry

cirEmIfStatsId		3.1.1751.2.18.11.3.1.1
Interface index (SSPPCCC) to the cirEm statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmIfStatsCellsEncodedHi		3.1.1751.2.18.11.3.1.2
Incoming cells from the outside media to the i/o port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmIfStatsCellsEncodedLo		3.1.1751.2.18.11.3.1.3
Incoming cells from the outside media to the i/o port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmIfStatsCellsDecodedHi		3.1.1751.2.18.11.3.1.4
Outgoing cells from the i/o port to the outside media
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmIfStatsCellsDecodedLo		3.1.1751.2.18.11.3.1.5
Outgoing cells from the i/o port to the outside media
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmIfStatsTimer		3.1.1751.2.18.11.3.1.6
Time, in seconds, since last reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..899

vbrIfStatsTable		3.1.1751.2.18.11.4
Table of statistics for an vbr interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrIfStatsEntry

vbrIfStatsEntry		3.1.1751.2.18.11.4.1
Row definition for the vbr statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrIfStatsEntry

vbrIfStatsId		3.1.1751.2.18.11.4.1.1
Interface index (SSPPCCC) to the vbr statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrIfStatsCellsEncodedHi		3.1.1751.2.18.11.4.1.2
Incoming cells from the outside media to the i/o port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrIfStatsCellsEncodedLo		3.1.1751.2.18.11.4.1.3
Incoming cells from the outside media to the i/o port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrIfStatsCellsDecodedHi		3.1.1751.2.18.11.4.1.4
Outgoing cells from the i/o port to the outside media
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrIfStatsCellsDecodedLo		3.1.1751.2.18.11.4.1.5
Outgoing cells from the i/o port to the outside media
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrIfStatsTimer		3.1.1751.2.18.11.4.1.6
Time, in seconds, since last reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..899

frLmiStatsTable		3.1.1751.2.18.11.5
Table of statistics for a Frame Relay LMI Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrLmiStatsEntry

frLmiStatsEntry		3.1.1751.2.18.11.5.1
Row definition for the Frame Realy LMI statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	FrLmiStatsEntry

frLmiStatsId		3.1.1751.2.18.11.5.1.1
Interface index (SSPPCCC) to the frame relay LMI statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frLmiStatsEnqRx		3.1.1751.2.18.11.5.1.2
number of STATUS ENQ messages received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frLmiStatsEnqTx		3.1.1751.2.18.11.5.1.3
number of STATUS ENQ messages transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frLmiStatsStatusRx		3.1.1751.2.18.11.5.1.4
number of STATUS messages received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frLmiStatsStatusTx		3.1.1751.2.18.11.5.1.5
number of STATUS messages transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frLmiStatsAsyncRx		3.1.1751.2.18.11.5.1.6
number of ASYNC STATUS messages received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frLmiStatsAsyncTx		3.1.1751.2.18.11.5.1.7
number of ASYNC STATUS messages transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frLmiStatsPktDisc		3.1.1751.2.18.11.5.1.8
The number of lmi messages discarded due to invalid length, receive sequence numbers, or other error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frLmiStatsT391Exp		3.1.1751.2.18.11.5.1.9
Link integrity verification polling timer expiry
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..899

frLmiStatsT392Exp		3.1.1751.2.18.11.5.1.10
Polling verification timer expiry
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..899

frLmiStatsLinkReset		3.1.1751.2.18.11.5.1.11
Number of times interface operational status was in service after system startup.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..899

frLmiStatsTimer		3.1.1751.2.18.11.5.1.12
Time since last reset for statistics - in seconds
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..899

bridgeStatsTable		3.1.1751.2.18.11.6
Table of statistics for a bridge interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BridgeStatsEntry

bridgeStatsEntry		3.1.1751.2.18.11.6.1
Row definition for the bridge interface statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	BridgeStatsEntry

bridgeStatsId		3.1.1751.2.18.11.6.1.1
Interface index (SSPPCCC) to the bridge
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bridgeStatsTimer		3.1.1751.2.18.11.6.1.2
Time, in seconds, since last reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeStatsBasePortDelayExceededDiscardsHi		3.1.1751.2.18.11.6.1.8
The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges. High-order 32 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeStatsBasePortDelayExceededDiscardsLo		3.1.1751.2.18.11.6.1.9
The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges. Low-order 32 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeStatsBasePortMtuExceededDiscardsHi		3.1.1751.2.18.11.6.1.10
The number of frames discarded by this port due to an excessive size. It is incremented by both transparent and source route bridges. High-order 32 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeStatsBasePortMtuExceededDiscardsLo		3.1.1751.2.18.11.6.1.11
The number of frames discarded by this port due to an excessive size. It is incremented by both transparent and source route bridges. Low-order 32 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeStatsTpPortInFramesHi		3.1.1751.2.18.11.6.1.12
The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames. High-order 32 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeStatsTpPortInFramesLo		3.1.1751.2.18.11.6.1.13
The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames. Low-order 32 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeStatsTpPortOutFramesHi		3.1.1751.2.18.11.6.1.14
The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames. High-order 32 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeStatsTpPortOutFramesLo		3.1.1751.2.18.11.6.1.15
The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames. Low-order 32 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeStatsTpPortInDiscardsHi		3.1.1751.2.18.11.6.1.16
Count of valid frames received which were discarded (i.e., filtered) by the Forwarding Process. High-order 32 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeStatsTpPortInDiscardsLo		3.1.1751.2.18.11.6.1.17
Count of valid frames received which were discarded (i.e., filtered) by the Forwarding Process. Low-order 32 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dbCirEmIfStatsTable		3.1.1751.2.18.11.7
Table of statistics for a dbCirEm interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DbCirEmIfStatsEntry

dbCirEmIfStatsEntry		3.1.1751.2.18.11.7.1
Row definition for the dbCirEm statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	DbCirEmIfStatsEntry

dbCirEmIfStatsId		3.1.1751.2.18.11.7.1.1
Interface index (SSPPCCC) to the dbCirEm statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

dbCirEmIfStatsCellsEncodedHi		3.1.1751.2.18.11.7.1.2
Incoming cells from the outside media to the i/o port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dbCirEmIfStatsCellsEncodedLo		3.1.1751.2.18.11.7.1.3
Incoming cells from the outside media to the i/o port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dbCirEmIfStatsCellsDecodedHi		3.1.1751.2.18.11.7.1.4
Outgoing cells from the i/o port to the outside media.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dbCirEmIfStatsCellsDecodedLo		3.1.1751.2.18.11.7.1.5
Outgoing cells from the i/o port to the outside media.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dbCirEmIfStatsTimer		3.1.1751.2.18.11.7.1.6
Time, in seconds, since last reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..899

atmImaStatsTable		3.1.1751.2.18.11.8
Table of statistics for an atmIma interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmImaStatsEntry

atmImaStatsEntry		3.1.1751.2.18.11.8.1
Row definition for the atmIma statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmImaStatsEntry

atmImaStatsId		3.1.1751.2.18.11.8.1.1
Interface index (SSPPCCC) to the atmIma statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmImaStatsTimer		3.1.1751.2.18.11.8.1.2
Time, in seconds, since last reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmImaStatsImaViolations		3.1.1751.2.18.11.8.1.3
ICP violations: count of errored, invalid or missing ICP cells during non-SES-IMA condition.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmImaStatsOifAnomalies		3.1.1751.2.18.11.8.1.4
The number of OIF anomalies during non-SES-IMA condition at the near-end.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmImaStatsNeTxNumFailures		3.1.1751.2.18.11.8.1.5
The number of times a near-end transmit failure alarm condition has been entered on this link.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmImaStatsNeRxNumFailures		3.1.1751.2.18.11.8.1.6
The number of times a near-end receive failure alarm condition has been entered on this link (i.e., LIF, LODS, Mis-Connected, RDI-IMA).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmImaStatsFeTxNumFailures		3.1.1751.2.18.11.8.1.7
The number of times a far-end transmit failure alarm condition has been entered on this link.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmImaStatsFeRxNumFailures		3.1.1751.2.18.11.8.1.8
The number of times a far-end receive failure alarm condition has been entered on this link (i.e. LIF, LODS, Mis-Connected, RDI-IMA).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmImaStatsTxStuffs		3.1.1751.2.18.11.8.1.9
Counts of stuff events inserted in the transmit direction.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmImaStatsRxStuffs		3.1.1751.2.18.11.8.1.10
Counts of stuff events detected in the receive direction.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsTable		3.1.1751.2.18.11.9
Table of statistics for an ILMI enabled interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IlmiStatsEntry

ilmiStatsEntry		3.1.1751.2.18.11.9.1
Row definition for the ILMI statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	IlmiStatsEntry

ilmiStatsId		3.1.1751.2.18.11.9.1.1
Interface index (SSPPCCC) for the ILMI interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

ilmiStatsTimer		3.1.1751.2.18.11.9.1.2
Time, in seconds, since last statistics reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsLinkResets		3.1.1751.2.18.11.9.1.3
Times connectivity has toggled between down and up.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsAttachPtChanged		3.1.1751.2.18.11.9.1.4
Times Attachment Point change was detected.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsAttachPtVerified		3.1.1751.2.18.11.9.1.5
Times Attachment Point was verified successfully.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsSecureLnkProcInit		3.1.1751.2.18.11.9.1.6
Times Secure Link Procedure was initiated.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsColdStartRx		3.1.1751.2.18.11.9.1.7
Times Cold Start trap was received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsColdStartTx		3.1.1751.2.18.11.9.1.8
Times Cold Start trap was transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsPduRx		3.1.1751.2.18.11.9.1.9
ilmi pdu received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsPduTx		3.1.1751.2.18.11.9.1.10
ilmi pdu transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsReqTimeouts		3.1.1751.2.18.11.9.1.11
Times getRequest of any type timed out.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ilmiStatsPacketDisc		3.1.1751.2.18.11.9.1.12
Times a received packet was discarded.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsTable		3.1.1751.2.18.11.12
Table of statistics for an ILMI enabled interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VuniIlmiStatsEntry

vuniIlmiStatsEntry		3.1.1751.2.18.11.12.1
Row definition for the ILMI statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	VuniIlmiStatsEntry

vuniIlmiStatsId		3.1.1751.2.18.11.12.1.1
Interface index (SSPPCCC) for the ILMI interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vuniIlmiVUNIId		3.1.1751.2.18.11.12.1.2
Virtual UNI number, second index to access the ILMI on virtual UNI interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..255

vuniIlmiStatsTimer		3.1.1751.2.18.11.12.1.3
Time, in seconds, since last statistics reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsLinkResets		3.1.1751.2.18.11.12.1.4
Times connectivity has toggled between down and up.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsAttachPtChanged		3.1.1751.2.18.11.12.1.5
Times Attachment Point change was detected.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsAttachPtVerified		3.1.1751.2.18.11.12.1.6
Times Attachment Point was verified successfully.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsSecureLnkProcInit		3.1.1751.2.18.11.12.1.7
Times Secure Link Procedure was initiated.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsColdStartRx		3.1.1751.2.18.11.12.1.8
Times Cold Start trap was received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsColdStartTx		3.1.1751.2.18.11.12.1.9
Times Cold Start trap was transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsPduRx		3.1.1751.2.18.11.12.1.10
vuniIlmi pdu received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsPduTx		3.1.1751.2.18.11.12.1.11
vuniIlmi pdu transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsReqTimeouts		3.1.1751.2.18.11.12.1.12
Times getRequest of any type timed out.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniIlmiStatsPacketDisc		3.1.1751.2.18.11.12.1.13
Times a received packet was discarded.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vuniResetIlmiStatistics		3.1.1751.2.18.11.12.1.14
Reset the ATM ILMI statistics counters for the given channel Id (SSPPCCC) and vuni Id
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noAction(1), reset(2)

atmPvcVccStatsTable		3.1.1751.2.18.12.1
Table of statistics for a channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmPvcVccStatsEntry

atmPvcVccStatsEntry		3.1.1751.2.18.12.1.1
Row definition for the connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmPvcVccStatsEntry

atmPvcVccStatsIfA		3.1.1751.2.18.12.1.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmPvcVccStatsVpiA		3.1.1751.2.18.12.1.1.2
VPI on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmPvcVccStatsVciA		3.1.1751.2.18.12.1.1.3
VCI on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmPvcVccStatsIfB		3.1.1751.2.18.12.1.1.4
Interface index (SSPPCCC) on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmPvcVccStatsVpiB		3.1.1751.2.18.12.1.1.5
VPI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmPvcVccStatsVciB		3.1.1751.2.18.12.1.1.6
VCI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmPvcVccStatsInCellCountHiA		3.1.1751.2.18.12.1.1.7
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsInCellCountLoA		3.1.1751.2.18.12.1.1.8
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOutCellCountHiA		3.1.1751.2.18.12.1.1.9
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOutCellCountLoA		3.1.1751.2.18.12.1.1.10
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsInCellCountHiB		3.1.1751.2.18.12.1.1.11
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsInCellCountLoB		3.1.1751.2.18.12.1.1.12
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.1.1.13
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.1.1.14
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsTimer		3.1.1751.2.18.12.1.1.15
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsFrwdErrCrrctnRateA2B		3.1.1751.2.18.12.1.1.16
Displays the Forward error correction rate being used by the FEC module in the A2B direction. This field is dynamic when Auto rates are selected. In other cases, it will display the rate set by the user.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4)

atmPvcVccStatsFrwdErrCrrctnRateB2A		3.1.1751.2.18.12.1.1.17
Displays the Forward error correction rate being used by the FEC module in the B2A direction. This field is dynamic when Auto rates are selected. In other cases, it will display the rate set by the user.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4)

atmPvcVccStatsInOdometerCellCountHiA		3.1.1751.2.18.12.1.1.18
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsInOdometerCellCountLoA		3.1.1751.2.18.12.1.1.19
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOutOdometerCellCountHiA		3.1.1751.2.18.12.1.1.20
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOutOdometerCellCountLoA		3.1.1751.2.18.12.1.1.21
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.12.1.1.22
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.12.1.1.23
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.1.1.24
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.1.1.25
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOdometerTimer		3.1.1751.2.18.12.1.1.26
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOdometerReset		3.1.1751.2.18.12.1.1.27
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

atmPvcVccStatsOamAisTxA		3.1.1751.2.18.12.1.1.28
Number of AIS cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOamAisRxA		3.1.1751.2.18.12.1.1.29
Number of AIS cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOamRdiTxA		3.1.1751.2.18.12.1.1.30
Number of RDI cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOamRdiRxA		3.1.1751.2.18.12.1.1.31
Number of RDI cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOamAisTxB		3.1.1751.2.18.12.1.1.32
Number of AIS cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOamAisRxB		3.1.1751.2.18.12.1.1.33
Number of AIS cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOamRdiTxB		3.1.1751.2.18.12.1.1.34
Number of RDI cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsOamRdiRxB		3.1.1751.2.18.12.1.1.35
Number of RDI cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsCellsDroppedA		3.1.1751.2.18.12.1.1.36
Cells Dropped on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsCellsTaggedA		3.1.1751.2.18.12.1.1.37
Cells Tagged on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsCellsDroppedB		3.1.1751.2.18.12.1.1.38
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVccStatsCellsTaggedB		3.1.1751.2.18.12.1.1.39
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsTable		3.1.1751.2.18.12.2
Table of statistics for a channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmPvcVpcStatsEntry

atmPvcVpcStatsEntry		3.1.1751.2.18.12.2.1
Row definition for the connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmPvcVpcStatsEntry

atmPvcVpcStatsIfA		3.1.1751.2.18.12.2.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmPvcVpcStatsVpiA		3.1.1751.2.18.12.2.1.2
VPI on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmPvcVpcStatsIfB		3.1.1751.2.18.12.2.1.3
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmPvcVpcStatsVpiB		3.1.1751.2.18.12.2.1.4
VPI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmPvcVpcStatsInCellCountHiA		3.1.1751.2.18.12.2.1.5
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsInCellCountLoA		3.1.1751.2.18.12.2.1.6
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOutCellCountHiA		3.1.1751.2.18.12.2.1.7
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOutCellCountLoA		3.1.1751.2.18.12.2.1.8
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsInCellCountHiB		3.1.1751.2.18.12.2.1.9
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsInCellCountLoB		3.1.1751.2.18.12.2.1.10
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOutCellCountHiB		3.1.1751.2.18.12.2.1.11
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOutCellCountLoB		3.1.1751.2.18.12.2.1.12
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsTimer		3.1.1751.2.18.12.2.1.13
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsInOdometerCellCountHiA		3.1.1751.2.18.12.2.1.14
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsInOdometerCellCountLoA		3.1.1751.2.18.12.2.1.15
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOutOdometerCellCountHiA		3.1.1751.2.18.12.2.1.16
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOutOdometerCellCountLoA		3.1.1751.2.18.12.2.1.17
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsInOdometerCellCountHiB		3.1.1751.2.18.12.2.1.18
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsInOdometerCellCountLoB		3.1.1751.2.18.12.2.1.19
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.2.1.20
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.2.1.21
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOdometerTimer		3.1.1751.2.18.12.2.1.22
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOdometerReset		3.1.1751.2.18.12.2.1.23
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

atmPvcVpcStatsOamAisTxA		3.1.1751.2.18.12.2.1.24
Number of AIS cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOamAisRxA		3.1.1751.2.18.12.2.1.25
Number of AIS cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOamRdiTxA		3.1.1751.2.18.12.2.1.26
Number of RDI cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOamRdiRxA		3.1.1751.2.18.12.2.1.27
Number of RDI cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOamAisTxB		3.1.1751.2.18.12.2.1.28
Number of AIS cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOamAisRxB		3.1.1751.2.18.12.2.1.29
Number of AIS cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOamRdiTxB		3.1.1751.2.18.12.2.1.30
Number of RDI cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsOamRdiRxB		3.1.1751.2.18.12.2.1.31
Number of RDI cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsCellsDroppedA		3.1.1751.2.18.12.2.1.32
Cells Dropped on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsCellsTaggedA		3.1.1751.2.18.12.2.1.33
Cells Tagged on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsCellsDroppedB		3.1.1751.2.18.12.2.1.34
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmPvcVpcStatsCellsTaggedB		3.1.1751.2.18.12.2.1.35
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsTable		3.1.1751.2.18.12.3
Table of statistics for a channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmSvcVccStatsEntry

atmSvcVccStatsEntry		3.1.1751.2.18.12.3.1
Row definition for the connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmSvcVccStatsEntry

atmSvcVccStatsIfA		3.1.1751.2.18.12.3.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmSvcVccStatsVpiA		3.1.1751.2.18.12.3.1.2
VPI on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmSvcVccStatsVciA		3.1.1751.2.18.12.3.1.3
VCI on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmSvcVccStatsIfB		3.1.1751.2.18.12.3.1.4
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmSvcVccStatsVpiB		3.1.1751.2.18.12.3.1.5
VPI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmSvcVccStatsVciB		3.1.1751.2.18.12.3.1.6
VCI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmSvcVccStatsInCellCountHiA		3.1.1751.2.18.12.3.1.7
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsInCellCountLoA		3.1.1751.2.18.12.3.1.8
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsOutCellCountHiA		3.1.1751.2.18.12.3.1.9
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsOutCellCountLoA		3.1.1751.2.18.12.3.1.10
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsInCellCountHiB		3.1.1751.2.18.12.3.1.11
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsInCellCountLoB		3.1.1751.2.18.12.3.1.12
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.3.1.13
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.3.1.14
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsTimer		3.1.1751.2.18.12.3.1.15
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsInOdometerCellCountHiA		3.1.1751.2.18.12.3.1.16
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsInOdometerCellCountLoA		3.1.1751.2.18.12.3.1.17
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsOutOdometerCellCountHiA		3.1.1751.2.18.12.3.1.18
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsOutOdometerCellCountLoA		3.1.1751.2.18.12.3.1.19
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.12.3.1.20
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.12.3.1.21
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.3.1.22
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.3.1.23
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsOdometerTimer		3.1.1751.2.18.12.3.1.24
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsOdometerReset		3.1.1751.2.18.12.3.1.25
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

atmSvcVccStatsCellsDroppedA		3.1.1751.2.18.12.3.1.26
Cells Dropped on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsCellsTaggedA		3.1.1751.2.18.12.3.1.27
Cells Tagged on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsCellsDroppedB		3.1.1751.2.18.12.3.1.28
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSvcVccStatsCellsTaggedB		3.1.1751.2.18.12.3.1.29
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsTable		3.1.1751.2.18.12.4
Table of Statistics entries
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpAtmAppPvcVccStatsEntry

ipAtmAppPvcVccStatsEntry		3.1.1751.2.18.12.4.1
Row definition for statistics attribution.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAtmAppPvcVccStatsEntry

ipAtmAppPvcVccStatsDestAddrA		3.1.1751.2.18.12.4.1.1
Statistics destination IP address
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

ipAtmAppPvcVccStatsSubnetMaskA		3.1.1751.2.18.12.4.1.2
The subnet mask of the destination IP address. Value is an IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

ipAtmAppPvcVccStatsIfB		3.1.1751.2.18.12.4.1.3
Interface index (SSPPCCC) on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

ipAtmAppPvcVccStatsVpiB		3.1.1751.2.18.12.4.1.4
VPI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

ipAtmAppPvcVccStatsVciB		3.1.1751.2.18.12.4.1.5
VCI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

ipAtmAppPvcVccStatsInCellCountHiA		3.1.1751.2.18.12.4.1.6
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsInCellCountLoA		3.1.1751.2.18.12.4.1.7
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOutCellCountHiA		3.1.1751.2.18.12.4.1.8
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOutCellCountLoA		3.1.1751.2.18.12.4.1.9
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsFramesInB		3.1.1751.2.18.12.4.1.10
number of frames received on side B.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsFramesOutB		3.1.1751.2.18.12.4.1.11
number of frames sent from side B.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsInCellCountHiB		3.1.1751.2.18.12.4.1.12
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsInCellCountLoB		3.1.1751.2.18.12.4.1.13
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.4.1.14
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.4.1.15
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsTimer		3.1.1751.2.18.12.4.1.16
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsInOdometerCellCountHiA		3.1.1751.2.18.12.4.1.17
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsInOdometerCellCountLoA		3.1.1751.2.18.12.4.1.18
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOutOdometerCellCountHiA		3.1.1751.2.18.12.4.1.19
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOutOdometerCellCountLoA		3.1.1751.2.18.12.4.1.20
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOdometerFramesInB		3.1.1751.2.18.12.4.1.21
Valid frames received at side B.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOdometerFramesOutB		3.1.1751.2.18.12.4.1.22
Valid frames transmitted from side B.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.12.4.1.23
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.12.4.1.24
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.4.1.25
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.4.1.26
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOdometerTimer		3.1.1751.2.18.12.4.1.27
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsOdometerReset		3.1.1751.2.18.12.4.1.28
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

ipAtmAppPvcVccStatsCellsDroppedB		3.1.1751.2.18.12.4.1.29
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppPvcVccStatsCellsTaggedB		3.1.1751.2.18.12.4.1.30
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsTable		3.1.1751.2.18.12.5
Table of statistics entries
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpAtmAppSvcVccStatsEntry

ipAtmAppSvcVccStatsEntry		3.1.1751.2.18.12.5.1
Row definition of statistics attributes.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAtmAppSvcVccStatsEntry

ipAtmAppSvcVccStatsDestAddrA		3.1.1751.2.18.12.5.1.1
Statistics destination IP address
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

ipAtmAppSvcVccStatsSubnetMaskA		3.1.1751.2.18.12.5.1.2
The subnet mask of the destination IP address. Value is an IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

ipAtmAppSvcVccStatsIfB		3.1.1751.2.18.12.5.1.3
Interface index (SSPPCCC) on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

ipAtmAppSvcVccStatsVpiB		3.1.1751.2.18.12.5.1.4
VPI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

ipAtmAppSvcVccStatsVciB		3.1.1751.2.18.12.5.1.5
VCI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

ipAtmAppSvcVccStatsInCellCountHiA		3.1.1751.2.18.12.5.1.6
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsInCellCountLoA		3.1.1751.2.18.12.5.1.7
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsOutCellCountHiA		3.1.1751.2.18.12.5.1.8
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsOutCellCountLoA		3.1.1751.2.18.12.5.1.9
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsFramesInB		3.1.1751.2.18.12.5.1.10
Frames received at side B.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsFramesOutB		3.1.1751.2.18.12.5.1.11
Frames transmitted from side B.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsInCellCountHiB		3.1.1751.2.18.12.5.1.12
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsInCellCountLoB		3.1.1751.2.18.12.5.1.13
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.5.1.14
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.5.1.15
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsTimer		3.1.1751.2.18.12.5.1.16
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsCellsDroppedB		3.1.1751.2.18.12.5.1.17
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmAppSvcVccStatsCellsTaggedB		3.1.1751.2.18.12.5.1.18
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsTable		3.1.1751.2.18.12.6
Table of statistics for a channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirEmAtmPvcVccStatsEntry

cirEmAtmPvcVccStatsEntry		3.1.1751.2.18.12.6.1
Row definition for the connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	CirEmAtmPvcVccStatsEntry

cirEmAtmPvcVccStatsIfA		3.1.1751.2.18.12.6.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmAtmPvcVccStatsIfB		3.1.1751.2.18.12.6.1.2
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmAtmPvcVccStatsVpiB		3.1.1751.2.18.12.6.1.3
VPI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

cirEmAtmPvcVccStatsVciB		3.1.1751.2.18.12.6.1.4
VCI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

cirEmAtmPvcVccStatsCellsEncodedHiA		3.1.1751.2.18.12.6.1.5
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsCellsEncodedLoA		3.1.1751.2.18.12.6.1.6
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsCellsDecodedHiA		3.1.1751.2.18.12.6.1.7
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsCellsDecodedLoA		3.1.1751.2.18.12.6.1.8
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsInCellCountHiB		3.1.1751.2.18.12.6.1.9
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsInCellCountLoB		3.1.1751.2.18.12.6.1.10
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.6.1.11
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.6.1.12
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsTimer		3.1.1751.2.18.12.6.1.13
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOdometerCellsEncodedHiA		3.1.1751.2.18.12.6.1.14
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOdometerCellsEncodedLoA		3.1.1751.2.18.12.6.1.15
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOdometerCellsDecodedHiA		3.1.1751.2.18.12.6.1.16
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOdometerCellsDecodedLoA		3.1.1751.2.18.12.6.1.17
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.12.6.1.18
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.12.6.1.19
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.6.1.20
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.6.1.21
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOdometerTimer		3.1.1751.2.18.12.6.1.22
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOdometerReset		3.1.1751.2.18.12.6.1.23
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

cirEmAtmPvcVccStatsOamAisTx		3.1.1751.2.18.12.6.1.24
Number of AIS cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOamAisRx		3.1.1751.2.18.12.6.1.25
Number of AIS cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOamRdiTx		3.1.1751.2.18.12.6.1.26
Number of RDI cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsOamRdiRx		3.1.1751.2.18.12.6.1.27
Number of RDI cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsCellsDroppedB		3.1.1751.2.18.12.6.1.28
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmPvcVccStatsCellsTaggedB		3.1.1751.2.18.12.6.1.29
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsTable		3.1.1751.2.18.12.7
Table of statistics for a channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrAtmPvcVccStatsEntry

frAtmPvcVccStatsEntry		3.1.1751.2.18.12.7.1
Row definition for the connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	FrAtmPvcVccStatsEntry

frAtmPvcVccStatsIfA		3.1.1751.2.18.12.7.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frAtmPvcVccStatsDlciA		3.1.1751.2.18.12.7.1.2
dlci - side A
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..1023

frAtmPvcVccStatsIfB		3.1.1751.2.18.12.7.1.3
Interface index (SSPPCCC) on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frAtmPvcVccStatsVpiB		3.1.1751.2.18.12.7.1.4
VPI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

frAtmPvcVccStatsVciB		3.1.1751.2.18.12.7.1.5
VCI on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

frAtmPvcVccStatsCellsEncodedHiA		3.1.1751.2.18.12.7.1.6
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsCellsEncodedLoA		3.1.1751.2.18.12.7.1.7
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsCellsDecodedHiA		3.1.1751.2.18.12.7.1.8
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsCellsDecodedLoA		3.1.1751.2.18.12.7.1.9
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsInCellCountHiB		3.1.1751.2.18.12.7.1.10
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsInCellCountLoB		3.1.1751.2.18.12.7.1.11
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.7.1.12
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.7.1.13
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsTimer		3.1.1751.2.18.12.7.1.14
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsFramesDroppedA		3.1.1751.2.18.12.7.1.15
Number of frames dropped for a given DLCI for A2B direction, only applicable to the input side.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOdometerCellsEncodedHiA		3.1.1751.2.18.12.7.1.16
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOdometerCellsEncodedLoA		3.1.1751.2.18.12.7.1.17
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOdometerCellsDecodedHiA		3.1.1751.2.18.12.7.1.18
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOdometerCellsDecodedLoA		3.1.1751.2.18.12.7.1.19
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.12.7.1.20
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.12.7.1.21
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.7.1.22
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.7.1.23
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOdometerTimer		3.1.1751.2.18.12.7.1.24
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOdometerFramesDroppedA		3.1.1751.2.18.12.7.1.25
Number of frames dropped for a given DLCI for A2B direction, only applicable to the input side.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOdometerReset		3.1.1751.2.18.12.7.1.26
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

frAtmPvcVccStatsOamAisTx		3.1.1751.2.18.12.7.1.27
Number of AIS cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOamAisRx		3.1.1751.2.18.12.7.1.28
Number of AIS cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOamRdiTx		3.1.1751.2.18.12.7.1.29
Number of RDI cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsOamRdiRx		3.1.1751.2.18.12.7.1.30
Number of RDI cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsAal5ErrFramesA		3.1.1751.2.18.12.7.1.31
Number of Aal5 Errored Frames, which are not dropped due to UPC in A2B dir, only applicable to Input Side
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsFramesTaggedA		3.1.1751.2.18.12.7.1.32
Number of Frames tagged due to UPC in A2B dir, only applicable to Input Side
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsCellsDroppedB		3.1.1751.2.18.12.7.1.33
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frAtmPvcVccStatsCellsTaggedB		3.1.1751.2.18.12.7.1.34
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsTable		3.1.1751.2.18.12.8
Table of statistics for a channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrFrPvcStatsEntry

frFrPvcStatsEntry		3.1.1751.2.18.12.8.1
Row definition for the connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	FrFrPvcStatsEntry

frFrPvcStatsIfA		3.1.1751.2.18.12.8.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frFrPvcStatsDlciA		3.1.1751.2.18.12.8.1.2
dlci - side A
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..1023

frFrPvcStatsIfB		3.1.1751.2.18.12.8.1.3
Interface index (SSPPCCC) on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

frFrPvcStatsDlciB		3.1.1751.2.18.12.8.1.4
dlci - side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..1023

frFrPvcStatsCellsEncodedHiA		3.1.1751.2.18.12.8.1.5
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsCellsEncodedLoA		3.1.1751.2.18.12.8.1.6
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsCellsDecodedHiA		3.1.1751.2.18.12.8.1.7
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsCellsDecodedLoA		3.1.1751.2.18.12.8.1.8
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsCellsEncodedHiB		3.1.1751.2.18.12.8.1.9
Cells encoded on side B- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsCellsEncodedLoB		3.1.1751.2.18.12.8.1.10
Cells encoded on side B- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsCellsDecodedHiB		3.1.1751.2.18.12.8.1.11
Cells decoded on side B- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsCellsDecodedLoB		3.1.1751.2.18.12.8.1.12
Cells decoded on side B- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsTimer		3.1.1751.2.18.12.8.1.13
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsFramesDroppedA		3.1.1751.2.18.12.8.1.14
Number of frames dropped for a given DLCI for A2B direction, only applicable to the input side.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsFramesDroppedB		3.1.1751.2.18.12.8.1.15
Number of frames dropped for a given DLCI for B2A direction, only applicable to the input side.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerCellsEncodedHiA		3.1.1751.2.18.12.8.1.16
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerCellsEncodedLoA		3.1.1751.2.18.12.8.1.17
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerCellsDecodedHiA		3.1.1751.2.18.12.8.1.18
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerCellsDecodedLoA		3.1.1751.2.18.12.8.1.19
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerCellsEncodedHiB		3.1.1751.2.18.12.8.1.20
Cells encoded on side B- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerCellsEncodedLoB		3.1.1751.2.18.12.8.1.21
Cells encoded on side B- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerCellsDecodedHiB		3.1.1751.2.18.12.8.1.22
Cells decoded on side B- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerCellsDecodedLoB		3.1.1751.2.18.12.8.1.23
Cells decoded on side B- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerTimer		3.1.1751.2.18.12.8.1.24
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerFramesDroppedA		3.1.1751.2.18.12.8.1.25
Number of frames dropped for a given DLCI for A2B direction, only applicable to the input side.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerFramesDroppedB		3.1.1751.2.18.12.8.1.26
Number of frames dropped for a given DLCI for B2A direction, only applicable to the input side.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsOdometerReset		3.1.1751.2.18.12.8.1.27
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

frFrPvcStatsAal5ErrFramesA		3.1.1751.2.18.12.8.1.28
Number of Aal5 Errored Frames, which are not dropped due to UPC in A2B dir, only applicable to Input Side
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsAal5ErrFramesB		3.1.1751.2.18.12.8.1.29
Number of Aal5 Errored Frames, which are not dropped due to UPC in B2A dir, only applicable to Input Side
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsFramesTaggedA		3.1.1751.2.18.12.8.1.30
Number of Frames tagged due to UPC in A2B dir, only applicable to Input Side
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frFrPvcStatsFramesTaggedB		3.1.1751.2.18.12.8.1.31
Number of Frames tagged due to UPC in B2A dir, only applicable to Input Side
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsTable		3.1.1751.2.18.12.9
Table of statistics for a channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrAtmPvcVccStatsEntry

vbrAtmPvcVccStatsEntry		3.1.1751.2.18.12.9.1
Row definition for the connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrAtmPvcVccStatsEntry

vbrAtmPvcVccStatsIfA		3.1.1751.2.18.12.9.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrAtmPvcVccStatsIfB		3.1.1751.2.18.12.9.1.2
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrAtmPvcVccStatsVpiB		3.1.1751.2.18.12.9.1.3
vpi - side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

vbrAtmPvcVccStatsVciB		3.1.1751.2.18.12.9.1.4
vci - side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

vbrAtmPvcVccStatsCellsEncodedHiA		3.1.1751.2.18.12.9.1.5
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsCellsEncodedLoA		3.1.1751.2.18.12.9.1.6
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsCellsDecodedHiA		3.1.1751.2.18.12.9.1.7
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsCellsDecodedLoA		3.1.1751.2.18.12.9.1.8
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsInCellCountHiB		3.1.1751.2.18.12.9.1.10
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsInCellCountLoB		3.1.1751.2.18.12.9.1.11
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.9.1.12
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.9.1.13
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsTimer		3.1.1751.2.18.12.9.1.14
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOdometerCellsEncodedHiA		3.1.1751.2.18.12.9.1.15
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOdometerCellsEncodedLoA		3.1.1751.2.18.12.9.1.16
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOdometerCellsDecodedHiA		3.1.1751.2.18.12.9.1.17
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOdometerCellsDecodedLoA		3.1.1751.2.18.12.9.1.18
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.12.9.1.19
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.12.9.1.20
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.9.1.21
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.9.1.22
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOdometerTimer		3.1.1751.2.18.12.9.1.23
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOdometerReset		3.1.1751.2.18.12.9.1.24
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

vbrAtmPvcVccStatsOamAisTx		3.1.1751.2.18.12.9.1.25
Number of AIS cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOamAisRx		3.1.1751.2.18.12.9.1.26
Number of AIS cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOamRdiTx		3.1.1751.2.18.12.9.1.27
Number of RDI cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsOamRdiRx		3.1.1751.2.18.12.9.1.28
Number of RDI cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsCellsDroppedB		3.1.1751.2.18.12.9.1.29
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmPvcVccStatsCellsTaggedB		3.1.1751.2.18.12.9.1.30
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsTable		3.1.1751.2.18.12.10
Table of statistics for a channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirEmCirEmPvcStatsEntry

cirEmCirEmPvcStatsEntry		3.1.1751.2.18.12.10.1
Row definition for the connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	CirEmCirEmPvcStatsEntry

cirEmCirEmPvcStatsIfA		3.1.1751.2.18.12.10.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmCirEmPvcStatsIfB		3.1.1751.2.18.12.10.1.2
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmCirEmPvcStatsCellsEncodedHiA		3.1.1751.2.18.12.10.1.3
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsCellsEncodedLoA		3.1.1751.2.18.12.10.1.4
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsCellsDecodedHiA		3.1.1751.2.18.12.10.1.5
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsCellsDecodedLoA		3.1.1751.2.18.12.10.1.6
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsCellsEncodedHiB		3.1.1751.2.18.12.10.1.7
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsCellsEncodedLoB		3.1.1751.2.18.12.10.1.8
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsCellsDecodedHiB		3.1.1751.2.18.12.10.1.9
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsCellsDecodedLoB		3.1.1751.2.18.12.10.1.10
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsTimer		3.1.1751.2.18.12.10.1.11
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsOdometerCellsEncodedHiA		3.1.1751.2.18.12.10.1.12
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsOdometerCellsEncodedLoA		3.1.1751.2.18.12.10.1.13
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsOdometerCellsDecodedHiA		3.1.1751.2.18.12.10.1.14
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsOdometerCellsDecodedLoA		3.1.1751.2.18.12.10.1.15
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsOdometerCellsEncodedHiB		3.1.1751.2.18.12.10.1.16
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsOdometerCellsEncodedLoB		3.1.1751.2.18.12.10.1.17
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsOdometerCellsDecodedHiB		3.1.1751.2.18.12.10.1.18
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsOdometerCellsDecodedLoB		3.1.1751.2.18.12.10.1.19
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsOdometerTimer		3.1.1751.2.18.12.10.1.20
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmCirEmPvcStatsOdometerReset		3.1.1751.2.18.12.10.1.21
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

vbrVbrPvcStatsTable		3.1.1751.2.18.12.11
Table of statistics for a channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrVbrPvcStatsEntry

vbrVbrPvcStatsEntry		3.1.1751.2.18.12.11.1
Row definition for the connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrVbrPvcStatsEntry

vbrVbrPvcStatsIfA		3.1.1751.2.18.12.11.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrVbrPvcStatsIfB		3.1.1751.2.18.12.11.1.2
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrVbrPvcStatsCellsEncodedHiA		3.1.1751.2.18.12.11.1.4
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsCellsEncodedLoA		3.1.1751.2.18.12.11.1.5
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsCellsDecodedHiA		3.1.1751.2.18.12.11.1.6
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsCellsDecodedLoA		3.1.1751.2.18.12.11.1.7
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsCellsEncodedHiB		3.1.1751.2.18.12.11.1.9
Cells encoded on side B- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsCellsEncodedLoB		3.1.1751.2.18.12.11.1.10
Cells encoded on side B- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsCellsDecodedHiB		3.1.1751.2.18.12.11.1.11
Cells decoded on side B- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsCellsDecodedLoB		3.1.1751.2.18.12.11.1.12
Cells decoded on side B- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsTimer		3.1.1751.2.18.12.11.1.13
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsOdometerCellsEncodedHiA		3.1.1751.2.18.12.11.1.14
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsOdometerCellsEncodedLoA		3.1.1751.2.18.12.11.1.15
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsOdometerCellsDecodedHiA		3.1.1751.2.18.12.11.1.16
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsOdometerCellsDecodedLoA		3.1.1751.2.18.12.11.1.17
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsOdometerCellsEncodedHiB		3.1.1751.2.18.12.11.1.18
Cells encoded on side B- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsOdometerCellsEncodedLoB		3.1.1751.2.18.12.11.1.19
Cells encoded on side B- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsOdometerCellsDecodedHiB		3.1.1751.2.18.12.11.1.20
Cells decoded on side B- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsOdometerCellsDecodedLoB		3.1.1751.2.18.12.11.1.21
Cells decoded on side B- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsOdometerTimer		3.1.1751.2.18.12.11.1.22
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrVbrPvcStatsOdometerReset		3.1.1751.2.18.12.11.1.23
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

bridgeBridgePvcStatsTable		3.1.1751.2.18.12.12
Table of bridge-bridge PVC connection statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BridgeBridgePvcStatsEntry

bridgeBridgePvcStatsEntry		3.1.1751.2.18.12.12.1
Row definition of statistics attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	BridgeBridgePvcStatsEntry

bridgeBridgePvcStatsIfA		3.1.1751.2.18.12.12.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

bridgeBridgePvcStatsIfB		3.1.1751.2.18.12.12.1.2
Interface index (SSPPCCC) on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

bridgeBridgePvcStatsCellsEncodedHiA		3.1.1751.2.18.12.12.1.3
Cells encoded on side A - (High order portion )
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsCellsEncodedLoA		3.1.1751.2.18.12.12.1.4
Cells encoded on side A - ( Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsCellsDecodedHiA		3.1.1751.2.18.12.12.1.5
Cells decoded on side A - ( High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsCellsDecodedLoA		3.1.1751.2.18.12.12.1.6
Cells decoded on side A - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsCellsEncodedHiB		3.1.1751.2.18.12.12.1.7
Cells encoded on side B - (High order portion )
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsCellsEncodedLoB		3.1.1751.2.18.12.12.1.8
Cells encoded on side B - (Low order portion )
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsCellsDecodedHiB		3.1.1751.2.18.12.12.1.9
Cells decoded on side B - (High order portion )
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsCellsDecodedLoB		3.1.1751.2.18.12.12.1.10
Cells decoded on side B -(Low order portion )
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsTimer		3.1.1751.2.18.12.12.1.11
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsOdometerCellsEncodedHiA		3.1.1751.2.18.12.12.1.12
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsOdometerCellsEncodedLoA		3.1.1751.2.18.12.12.1.13
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsOdometerCellsDecodedHiA		3.1.1751.2.18.12.12.1.14
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsOdometerCellsDecodedLoA		3.1.1751.2.18.12.12.1.15
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsOdometerCellsEncodedHiB		3.1.1751.2.18.12.12.1.16
Cells encoded on side B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsOdometerCellsEncodedLoB		3.1.1751.2.18.12.12.1.17
Cells encoded on side B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsOdometerCellsDecodedHiB		3.1.1751.2.18.12.12.1.18
Cells decoded on side B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsOdometerCellsDecodedLoB		3.1.1751.2.18.12.12.1.19
Cells decoded on side B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsOdometerTimer		3.1.1751.2.18.12.12.1.20
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeBridgePvcStatsOdometerReset		3.1.1751.2.18.12.12.1.21
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

bridgeAtmPvcVccStatsTable		3.1.1751.2.18.12.13
Table of statisics
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BridgeAtmPvcVccStatsEntry

bridgeAtmPvcVccStatsEntry		3.1.1751.2.18.12.13.1
Row definition for the connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	BridgeAtmPvcVccStatsEntry

bridgeAtmPvcVccStatsIfA		3.1.1751.2.18.12.13.1.1
Interface index (SSPPCCC) on side A
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

bridgeAtmPvcVccStatsIfB		3.1.1751.2.18.12.13.1.2
Interface index (SSPPCCC) on side B
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

bridgeAtmPvcVccStatsVpiB		3.1.1751.2.18.12.13.1.3
vpi - side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

bridgeAtmPvcVccStatsVciB		3.1.1751.2.18.12.13.1.4
vci - side B
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

bridgeAtmPvcVccStatsCellsEncodedHiA		3.1.1751.2.18.12.13.1.5
number of cells encoded on side A - (High order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsCellsEncodedLoA		3.1.1751.2.18.12.13.1.6
number of cells encoded on side A - (Low order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsCellsDecodedHiA		3.1.1751.2.18.12.13.1.7
number of cells decoded on side A - (High order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsCellsDecodedLoA		3.1.1751.2.18.12.13.1.8
number of cells decoded on side A - (Low order portion).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsInCellCountHiB		3.1.1751.2.18.12.13.1.9
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsInCellCountLoB		3.1.1751.2.18.12.13.1.10
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.13.1.11
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.13.1.12
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsTimer		3.1.1751.2.18.12.13.1.13
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOdometerCellsEncodedHiA		3.1.1751.2.18.12.13.1.14
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOdometerCellsEncodedLoA		3.1.1751.2.18.12.13.1.15
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOdometerCellsDecodedHiA		3.1.1751.2.18.12.13.1.16
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOdometerCellsDecodedLoA		3.1.1751.2.18.12.13.1.17
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.12.13.1.18
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.12.13.1.19
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.13.1.20
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.13.1.21
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOdometerTimer		3.1.1751.2.18.12.13.1.22
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOdometerReset		3.1.1751.2.18.12.13.1.23
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

bridgeAtmPvcVccStatsOamAisTx		3.1.1751.2.18.12.13.1.24
Number of AIS cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOamAisRx		3.1.1751.2.18.12.13.1.25
Number of AIS cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOamRdiTx		3.1.1751.2.18.12.13.1.26
Number of RDI cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsOamRdiRx		3.1.1751.2.18.12.13.1.27
Number of RDI cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsCellsDroppedB		3.1.1751.2.18.12.13.1.28
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeAtmPvcVccStatsCellsTaggedB		3.1.1751.2.18.12.13.1.29
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsTable		3.1.1751.2.18.12.14
Table of statistics for a CES SPVC channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CirEmAtmSpvcVccStatsEntry

cirEmAtmSpvcVccStatsEntry		3.1.1751.2.18.12.14.1
Row definition for the CES SPVC connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	CirEmAtmSpvcVccStatsEntry

cirEmAtmSpvcVccStatsIfA		3.1.1751.2.18.12.14.1.1
Interface index for side A, the circuit emulation side, of a circuit emulation-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmAtmSpvcVccStatsIfB		3.1.1751.2.18.12.14.1.2
Interface index for side B, the atm side, of a circuit emulation-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

cirEmAtmSpvcVccStatsVpiB		3.1.1751.2.18.12.14.1.3
VPI value for side B, the atm side, of a circuit emulation-atm SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

cirEmAtmSpvcVccStatsVciB		3.1.1751.2.18.12.14.1.4
VCI value for side B, the atm side, of a circuit emulation-atm SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

cirEmAtmSpvcVccStatsCellsEncodedHiA		3.1.1751.2.18.12.14.1.5
Cells encoded on side A - (High order portion )
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsCellsEncodedLoA		3.1.1751.2.18.12.14.1.6
Cells encoded on side A - ( Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsCellsDecodedHiA		3.1.1751.2.18.12.14.1.7
Cells decoded on side A - ( High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsCellsDecodedLoA		3.1.1751.2.18.12.14.1.8
Cells decoded on side A - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsInCellCountHiB		3.1.1751.2.18.12.14.1.9
Valid Cells received on B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsInCellCountLoB		3.1.1751.2.18.12.14.1.10
Valid Cells received on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.14.1.11
Valid cells transmitted on B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.14.1.12
Valid cells transmitted on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsTimer		3.1.1751.2.18.12.14.1.13
Number of seconds since stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsOdometerCellsEncodedHiA		3.1.1751.2.18.12.14.1.14
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsOdometerCellsEncodedLoA		3.1.1751.2.18.12.14.1.15
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsOdometerCellsDecodedHiA		3.1.1751.2.18.12.14.1.16
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsOdometerCellsDecodedLoA		3.1.1751.2.18.12.14.1.17
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.12.14.1.18
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.12.14.1.19
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.14.1.20
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.14.1.21
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsOdometerTimer		3.1.1751.2.18.12.14.1.22
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsOdometerReset		3.1.1751.2.18.12.14.1.23
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

cirEmAtmSpvcVccStatsCellsDroppedB		3.1.1751.2.18.12.14.1.24
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cirEmAtmSpvcVccStatsCellsTaggedB		3.1.1751.2.18.12.14.1.25
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsTable		3.1.1751.2.18.12.15
Table of statistics for a TE SPVC channel connection.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VbrAtmSpvcVccStatsEntry

vbrAtmSpvcVccStatsEntry		3.1.1751.2.18.12.15.1
Row definition for the TE SPVC connection statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	VbrAtmSpvcVccStatsEntry

vbrAtmSpvcVccStatsIfA		3.1.1751.2.18.12.15.1.1
Interface index for side A, the variable bit rate side, of a variable bit rate-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrAtmSpvcVccStatsIfB		3.1.1751.2.18.12.15.1.2
Interface index for side B, the atm side, of a variable bit rate-atm SPVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

vbrAtmSpvcVccStatsVpiB		3.1.1751.2.18.12.15.1.3
VPI value for side B, the atm side, of a variable bit rate-atm SPVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

vbrAtmSpvcVccStatsVciB		3.1.1751.2.18.12.15.1.4
VCI value for side B, the atm side, of a variable bit rate-atm SPVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

vbrAtmSpvcVccStatsCellsEncodedHiA		3.1.1751.2.18.12.15.1.5
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsCellsEncodedLoA		3.1.1751.2.18.12.15.1.6
ells encoded on side A - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsCellsDecodedHiA		3.1.1751.2.18.12.15.1.7
Cells decoded on side A - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsCellsDecodedLoA		3.1.1751.2.18.12.15.1.8
Cells decoded on side A - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsInCellCountHiB		3.1.1751.2.18.12.15.1.9
Valid Cells received on B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsInCellCountLoB		3.1.1751.2.18.12.15.1.10
Valid Cells received on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.15.1.11
Valid cells transmitted on B -(High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.15.1.12
Valid cells transmitted on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsTimer		3.1.1751.2.18.12.15.1.13
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsOdometerCellsEncodedHiA		3.1.1751.2.18.12.15.1.14
Cells encoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsOdometerCellsEncodedLoA		3.1.1751.2.18.12.15.1.15
Cells encoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsOdometerCellsDecodedHiA		3.1.1751.2.18.12.15.1.16
Cells decoded on side A- (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsOdometerCellsDecodedLoA		3.1.1751.2.18.12.15.1.17
Cells decoded on side A- (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.12.15.1.18
Valid Cells received on B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.12.15.1.19
Valid Cells received on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.15.1.20
Valid Cells transmitted on B -(High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.15.1.21
Valid Cells transmitted on B -(Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsOdometerTimer		3.1.1751.2.18.12.15.1.22
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsOdometerReset		3.1.1751.2.18.12.15.1.23
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

vbrAtmSpvcVccStatsCellsDroppedB		3.1.1751.2.18.12.15.1.24
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

vbrAtmSpvcVccStatsCellsTaggedB		3.1.1751.2.18.12.15.1.25
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsTable		3.1.1751.2.18.12.16
Table of statistics for a ATM SPVC channel connection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmSpvcVccStatsEntry

atmSpvcVccStatsEntry		3.1.1751.2.18.12.16.1
Row definition for the ATM SPVC connection statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmSpvcVccStatsEntry

atmSpvcVccStatsIfA		3.1.1751.2.18.12.16.1.1
Interface index for side A of an ATM-to-ATM PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmSpvcVccStatsVpiA		3.1.1751.2.18.12.16.1.2
VPI value for side A of an ATM-to-ATM PVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmSpvcVccStatsVciA		3.1.1751.2.18.12.16.1.3
VCI value for side A of an ATM-to-ATM PVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmSpvcVccStatsIfB		3.1.1751.2.18.12.16.1.4
Interface index for side B of an ATM-to-ATM PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

atmSpvcVccStatsVpiB		3.1.1751.2.18.12.16.1.5
VPI value for side B of an ATM-to-ATM PVC VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

atmSpvcVccStatsVciB		3.1.1751.2.18.12.16.1.6
VCI value for side B of an ATM-to-ATM PVC VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

atmSpvcVccStatsInCellCountHiA		3.1.1751.2.18.12.16.1.7
Valid Cells received on A - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsInCellCountLoA		3.1.1751.2.18.12.16.1.8
Valid Cells received on A - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsOutCellCountHiA		3.1.1751.2.18.12.16.1.9
Valid cells transmitted on A -(High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsOutCellCountLoA		3.1.1751.2.18.12.16.1.10
Valid cells transmitted on A -(Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsInCellCountHiB		3.1.1751.2.18.12.16.1.11
Valid Cells received on B - (High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsInCellCountLoB		3.1.1751.2.18.12.16.1.12
Valid Cells received on B - (Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsOutCellCountHiB		3.1.1751.2.18.12.16.1.13
Valid cells transmitted on B -(High order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsOutCellCountLoB		3.1.1751.2.18.12.16.1.14
Valid cells transmitted on B -(Low order portion)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsTimer		3.1.1751.2.18.12.16.1.15
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsFrwdErrCrrctnRateA2B		3.1.1751.2.18.12.16.1.16
Displays the Forward error correction rate being used by the FEC module in the A2B direction. This field is dynamic when Auto rates are selected. In other cases, it will display the rate set by the user.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4)

atmSpvcVccStatsFrwdErrCrrctnRateB2A		3.1.1751.2.18.12.16.1.17
Displays the Forward error correction rate being used by the FEC module in the B2A direction. This field is dynamic when Auto rates are selected. In other cases, it will display the rate set by the user.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4)

atmSpvcVccStatsInOdometerCellCountHiA		3.1.1751.2.18.12.16.1.18
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsInOdometerCellCountLoA		3.1.1751.2.18.12.16.1.19
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsOutOdometerCellCountHiA		3.1.1751.2.18.12.16.1.20
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsOutOdometerCellCountLoA		3.1.1751.2.18.12.16.1.21
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsInOdometerCellCountHiB		3.1.1751.2.18.12.16.1.22
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsInOdometerCellCountLoB		3.1.1751.2.18.12.16.1.23
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.16.1.24
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.16.1.25
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsOdometerTimer		3.1.1751.2.18.12.16.1.26
Number of seconds since odometer was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsOdometerReset		3.1.1751.2.18.12.16.1.27
Odometer reset button.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

atmSpvcVccStatsCellsDroppedA		3.1.1751.2.18.12.16.1.28
Cells Dropped on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsCellsTaggedA		3.1.1751.2.18.12.16.1.29
Cells Tagged on the Incoming side of A
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsCellsDroppedB		3.1.1751.2.18.12.16.1.30
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSpvcVccStatsCellsTaggedB		3.1.1751.2.18.12.16.1.31
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAtmArpSrvConnType		3.1.1751.2.18.13.1
type of Arp Server connection
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pvc(1), svc(2), none(3)

ipAtmIpAddr		3.1.1751.2.18.13.2
Local IP Address
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ipAtmIpMask		3.1.1751.2.18.13.3
Local IP Mask
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

atmArpTable		3.1.1751.2.18.13.4
ARP Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmArpEntry

atmArpEntry		3.1.1751.2.18.13.4.1
ARP Table entry
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmArpEntry

atmArpIpAddress		3.1.1751.2.18.13.4.1.1
IP address of the IP host described in APR table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

atmArpAtmAddress		3.1.1751.2.18.13.4.1.2
ATM address of the IP host.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(20)

atmArpAddrType		3.1.1751.2.18.13.4.1.3
Type of ATM address value of atmArp address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nsap(1), e164(2), e164nsap(3)

atmArpEntryState		3.1.1751.2.18.13.4.1.4
State of this entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	valid(1), invalid(2), unconnected(3), permanent(4), pendingAtmAddr(5), pendingIpAddr(6), pendingConnect(7)

atmArpEntryRowStatus		3.1.1751.2.18.13.4.1.5
RowStatus of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

appIpRouteTable		3.1.1751.2.18.13.5
Application IP Routing table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AppIpRouteEntry

appIpRouteEntry		3.1.1751.2.18.13.5.1
A route to a particular destination.
Status: current	Access: not-accessible
OBJECT-TYPE
	AppIpRouteEntry

appIpRouteDest		3.1.1751.2.18.13.5.1.1
The destination IP address of this route. An entry with a value of 0.0.0.0 is not valid route.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

appIpRouteMask		3.1.1751.2.18.13.5.1.2
Mask for Ip route, usefull only for SENS stack VxWorks
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

appIpRouteMetric1		3.1.1751.2.18.13.5.1.3
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes appIpRouteProto value. If this metric is not used, its value should be set to 1.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..255

appIpRouteNextHop		3.1.1751.2.18.13.5.1.4
The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

appIpRouteState		3.1.1751.2.18.13.5.1.5
Current state of route
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	invalid(0), inuse(1), notinuse(2), error(3)

iispCbrRoutTable		3.1.1751.2.18.14.1
IISP CBR Routing Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IispCbrRoutEntry

iispCbrRoutEntry		3.1.1751.2.18.14.1.1
IISP CBR Table Entry
Status: current	Access: not-accessible
OBJECT-TYPE
	IispCbrRoutEntry

iispCbrRoutLength		3.1.1751.2.18.14.1.1.1
length in bits
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

iispCbrRoutNsapAddr		3.1.1751.2.18.14.1.1.2
nsap address
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(1..20)

iispCbrRoutIfIndex		3.1.1751.2.18.14.1.1.3
Interface index - SSPPCCC
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

iispCbrRoutRowStatus		3.1.1751.2.18.14.1.1.4
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

iispVbrRoutTable		3.1.1751.2.18.14.2
IISP CBR Routing Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IispVbrRoutEntry

iispVbrRoutEntry		3.1.1751.2.18.14.2.1
IISP CBR Table Entry
Status: current	Access: not-accessible
OBJECT-TYPE
	IispVbrRoutEntry

iispVbrRoutLength		3.1.1751.2.18.14.2.1.1
length in bits
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

iispVbrRoutNsapAddr		3.1.1751.2.18.14.2.1.2
nsap address
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(1..20)

iispVbrRoutIfIndex		3.1.1751.2.18.14.2.1.3
Interface index - SSPPCCC
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

iispVbrRoutRowStatus		3.1.1751.2.18.14.2.1.4
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

iispCbrRouteTable		3.1.1751.2.18.14.3
IISP CBR Routing Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IispCbrRouteEntry

iispCbrRouteEntry		3.1.1751.2.18.14.3.1
IISP CBR Route Entry
Status: current	Access: not-accessible
OBJECT-TYPE
	IispCbrRouteEntry

iispCbrRouteLength		3.1.1751.2.18.14.3.1.1
length in bits
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

iispCbrRouteNsapAddr		3.1.1751.2.18.14.3.1.2
nsap address
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(1..20)

iispCbrRouteIfIndex		3.1.1751.2.18.14.3.1.3
Interface index - SSPPCCC
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

iispCbrRouteRowStatus		3.1.1751.2.18.14.3.1.4
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

iispCbrRouteIfVuniId		3.1.1751.2.18.14.3.1.5
Virtual UNI interface VUNI Id
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..255

iispCbrRouteType		3.1.1751.2.18.14.3.1.6
Type of Route, Categorisation of an Endpoint Route or an intermediate Route
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	drmRouteTypeAny(0), drmRouteTypeAtm(1), drmRouteTypeIisp(2), drmRouteTypeIlmiUser(3), drmRouteTypeIsdn(11), drmRouteTypeCe(21), drmRouteTypeSs7(31), drmRouteTypeFr(41), drmRouteTypeCasTrunk(51), drmRouteTypeEndPtAtm(132), drmRouteTypeEndPtCe(133), drmRouteTypeEndPtTe(134), drmRouteTypeEndPtIsdn(135), drmRouteTypeEndPtIp(136), drmRouteTypeEndPtFr(137)

iispCbrRouteDest		3.1.1751.2.18.14.3.1.7
Type of Destination, Categorisation of an Endpoint destination or an intermediate destination
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	drmRouteDestAny(0), drmRouteDestAtm(1), drmRouteDestIsdn(2), drmRouteDestCe(3), drmRouteDestSs7(4), drmRouteDestFr(5), drmRouteDestAalIwf(6), drmRouteDestEndPtAtm(15), drmRouteDestEndPtCe(16), drmRouteDestEndPtTe(17), drmRouteDestEndPtIsdn(18), drmRouteTypeEndPtIp(19), drmRouteTypeEndPtFr(20), drmRouteTypeEndPtCas(21)

iispVbrRouteTable		3.1.1751.2.18.14.4
IISP CBR Routing Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IispVbrRouteEntry

iispVbrRouteEntry		3.1.1751.2.18.14.4.1
IISP CBR Table Entry
Status: current	Access: not-accessible
OBJECT-TYPE
	IispVbrRouteEntry

iispVbrRouteLength		3.1.1751.2.18.14.4.1.1
length in bits
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

iispVbrRouteNsapAddr		3.1.1751.2.18.14.4.1.2
nsap address
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(1..20)

iispVbrRouteIfIndex		3.1.1751.2.18.14.4.1.3
In most cases, it is the I/O Interface index - SSPPCCC. However, in case of ATM Trunking's Narrowband routing and Broadband routing, this is either the CAS trunk group ID, or the remote IWF ID, which are 1 to 3 digits decimal numbers
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

iispVbrRouteRowStatus		3.1.1751.2.18.14.4.1.4
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

iispVbrRouteIfVuniId		3.1.1751.2.18.14.4.1.5
Virtual UNI interface VUNI Id
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..255

iispVbrRouteType		3.1.1751.2.18.14.4.1.6
Type of Route, Categorisation of an Endpoint Route or an intermediate Route
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	drmRouteTypeAny(0), drmRouteTypeAtm(1), drmRouteTypeIisp(2), drmRouteTypeIlmiUser(3), drmRouteTypeIsdn(11), drmRouteTypeCe(21), drmRouteTypeSs7(31), drmRouteTypeFr(41), drmRouteTypeCasTrunk(51), drmRouteTypeIwfTrunk(61), drmRouteTypeEndPtAtm(132), drmRouteTypeEndPtCe(133), drmRouteTypeEndPtTe(134), drmRouteTypeEndPtIsdn(135), drmRouteTypeEndPtIp(136), drmRouteTypeEndPtFr(137)

iispVbrRouteDest		3.1.1751.2.18.14.4.1.7
Type of Destination, Categorisation of an Endpoint destination or an intermediate destination
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	drmRouteDestAny(0), drmRouteDestAtm(1), drmRouteDestIsdn(2), drmRouteDestCe(3), drmRouteDestSs7(4), drmRouteDestFr(5), drmRouteDestAalIwf(6), drmRouteDestEndPtAny(14), drmRouteDestEndPtAtm(15), drmRouteDestEndPtCe(16), drmRouteDestEndPtTe(17), drmRouteDestEndPtIsdn(18), drmRouteTypeEndPtIp(19), drmRouteTypeEndPtFr(20), drmRouteTypeEndPtCas(21), drmRouteTypeEndPtTrkIwf(22)

pvcFailureReasonCode		3.1.1751.2.18.15.1
An identified reason why an ATM PVC connection request failed. aal2CuTimerOutOfRange(298): this error code is generated when the aal2CuTimer value is out of range and the valid reanges is 0 to 8 (0 - 40 msec of delay). unrecognizableDigitCollectTypeA2B(299): unrecognizable digital tone set in connection A2B direction. unrecognizableDigitCollectTypeB2A(300): unrecognizable digital tone set in connection B2A direction.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	vpiVciUnavailableA2B(1), vpiVciUnavailableB2A(2), bandwidthUnavailableA2B(3), bandwidthUnavailableB2A(4), qosUnavailableA2B(5), qosUnavailableB2A(6), internalResourceUnavailable(7), cantUseSignalingChnlIgrsA2B(8), cantUseSignalingChnlEgrsA2B(9), cantUseSignalingChnlIgrsB2A(10), cantUseSignalingChnlEgrsB2A(11), cantUseManagementChnlIgrsA2B(12), cantUseManagementChnlEgrsA2B(13), cantUseManagementChnlIgrsB2A(14), cantUseManagementChnlEgrsB2A(15), vcLessThanVcMinIgrsA2B(16), vcLessThanVcMinEgrsA2B(17), vcLessThanVcMinIgrsB2A(18), vcLessThanVcMinEgrsB2A(19), vcGreaterThanVcMaxIgrsA2B(20), vcGreaterThanVcMaxEgrsA2B(21), vcGreaterThanVcMaxIgrsB2A(22), vcGreaterThanVcMaxEgrsB2A(23), vpLessThanVpMinIgrsA2B(24), vpLessThanVpMinEgrsA2B(25), vpLessThanVpMinIgrsB2A(26), vpLessThanVpMinEgrsB2A(27), vpGreaterThanVpMaxIgrsA2B(28), vpGreaterThanVpMaxEgrsA2B(29), vpGreaterThanVpMaxIgrsB2A(30), vpGreaterThanVpMaxEgrsB2A(31), vpGreaterThanVpMaxIispIgrsA2B(32), vpGreaterThanVpMaxIispEgrsA2B(33), vpGreaterThanVpMaxIispIgrsB2A(34), vpGreaterThanVpMaxIispEgrsB2A(35), rsvdChnlRangeIgrsA2B(36), rsvdChnlRangeEgrsA2B(37), rsvdChnlRangeIgrsB2A(38), rsvdChnlRangeEgrsB2A(39), internalSrvcTypeUnavailableA2B(40), internalSrvcTypeUnavailableB2A(41), unrecognizableBindTypeEgrsA2B(42), unrecognizableBindTypeEgrsB2A(43), callWithoutConnections(44), callDataStructuresUnavailable(45), cnctnDataStructuresUnavailable(46), nullTrafficParametersRejectedA2B(47), nullTrafficParametersRejectedB2A(48), vpiWithinSvcRangeIgrsA2B(49), vpiWithinSvcRangeEgrsA2B(50), vpiWithinSvcRangeIgrsB2A(51), vpiWithinSvcRangeEgrsB2A(52), vpiInReservedListA2B(53), vpiInReservedListB2A(54), vpiInPvcListA2B(55), vpiInPvcListB2A(56), vpiInReleasedListA2B(57), vpiInReleasedListB2A(58), vciIsNotNullInVpcIgrsA2B(59), vciIsNotNullInVpcEgrsA2B(60), vciIsNotNullInVpcIgrsB2A(61), vciIsNotNullInVpcEgrsB2A(62), vpiInVpcReservedListA2B(63), vpiInVpcReservedListB2A(64), vpiVciInReservedListA2B(65), vpiVciInReservedListB2A(66), vpiInVpcPvcListA2B(67), vpiInVpcPvcListB2A(68), vpiVciInPvcListA2B(69), vpiVciInPvcListB2A(70), vpiInVpcReleasedListA2B(71), vpiInVpcReleasedListB2A(72), vpiVciInReleasedListA2B(73), vpiVciInReleasedListB2A(74), illegalMulticaseIdA2B(75), illegalMulticaseIdB2A(76), unsupportedConnectionA2B(77), unsupportedConnectionB2A(78), connectionsUnavailableInModuleA2B(79), connectionsUnavailableInModuleB2A(80), cbrBandwidthUnavailableIgrsA2B(81), cbrBandwidthUnavailableEgrsA2B(82), cbrBandwidthUnavailableIgrsB2A(83), cbrBandwidthUnavailableEgrsB2A(84), vbrBandwidthUnavailableIgrsA2B(85), vbrBandwidthUnavailableEgrsA2B(86), vbrBandwidthUnavailableIgrsB2A(87), vbrBandwidthUnavailableEgrsB2A(88), vpiVciWithinSvcRangeIgrsA2B(89), vpiVciWithinSvcRangeEgrsA2B(90), vpiVciWithinSvcRangeIgrsB2A(91), vpiVciWithinSvcRangeEgrsB2A(92), multicastDataStructuresUnavailable(93), semaphoreTimeout(94), dlciFoundInReservedList(95), dlciFoundInPvcList(96), dlciFoundInReleasedList(97), invalidDlci(98), slotA-OutOfRange(99), portA-OutOfRange(100), channelA-OutOfRange(101), moduleA-Uninitialized(102), physicalPortA-Uninitialized(103), channelA-NotBound(104), moduleA-UnrecognizablePortType(105), slotB-OutOfRange(106), portB-OutOfRange(107), channelB-OutOfRange(108), moduleB-Uninitialized(109), physicalPortB-Uninitialized(110), channelB-NotBound(111), moduleB-UnrecognizablePortType(112), interfaceA-NotAtm(113), interfaceB-NotAtm(114), unrecognizableServiceTypeA2B(115), unrecognizableServiceTypeB2A(116), unrecognizableSarTypeA2B(117), unrecognizableSarTypeB2A(118), interfaceA-NotCircuitEmulation(119), interfaceB-NotCircuitEmulation(120), unrecognizableSilenceDetectionMode(121), unrecognizableEchoCancellationMode(122), unrecognizableVoiceCompressionMode(123), interfaceA-NotVbr(124), interfaceB-NotVbr(125), interfaceA-NotFrameRelay(126), interfaceB-NotFrameRelay(127), interfaceA-InHdlcPvcList(128), interfaceA-InHdlcReleasedList(129), interfaceA-InHdlcReservedList(130), interfaceA-InTerminalEmulationPvcList(131), interfaceA-InTerminalEmulationReleasedList(132), interfaceA-InTerminalEmulationReservedList(133), interfaceA-InCircuitEmulationPvcList(134), interfaceA-InCircuitEmulationReleasedList(135), interfaceA-InCircuitEmulationReservedList(136), notNullVpcInNoisyLinkA2BIgrs(137), notNullVpcInNoisyLinkA2BEgrs(138), invalidVccInNoisyLinkA2BIgrs(139), invalidVccInNoisyLinkA2BEgrs(140), unsupportedFrwdErrCorrectValueA2B(141), interfaceB-InHdlcPvcList(142), interfaceB-InHdlcReleasedList(143), interfaceB-InHdlcReservedList(144), interfaceB-InTerminalEmulationPvcList(145), interfaceB-InTerminalEmulationReleasedList(146), interfaceB-InTerminalEmulationReservedList(147), interfaceB-InCircuitEmulationPvcList(148), interfaceB-InCircuitEmulationReleasedList(149), interfaceB-InCircuitEmulationReservedList(150), notNullVpcInNoisyLinkB2AIgrs(151), notNullVpcInNoisyLinkB2AEgrs(152), invalidVccInNoisyLinkB2AIgrs(153), invalidVccInNoisyLinkB2AEgrs(154), unsupportedFrwdErrCorrectValueB2A(155), interfaceInUse(156), unsupportedFrwdErrCorrectSettings(157), unsupportedFlowSettings(158), frwdErrCorrectResourceInternalError(159), unsupportedConnection(160), ipDestAddrSubnetAInReservedList(161), ipDestAddrSubnetAInPvcList(162), ipDestAddrSubnetAInReleasedList(163), ipDestAddrSubnetBInReservedList(164), ipDestAddrSubnetBInPvcList(165), ipDestAddrSubnetBInReleasedList(166), notCpuIpInterfaceA(167), ipResourceUnavailable(168), fecAutoInSimplexNotValid(169), fecResourceUnavailable(170), notBridgeInterfaceA(171), notBridgeInterfaceB(172), invalidBridgePortA2B(173), invalidBridgePortB2A(174), interfaceAInBridgePvcList(175), interfaceBInBridgePvcList(176), interfaceAInBridgeReleasedList(177), interfaceBInBridgeReleasedList(178), interfaceAInBridgeReservedList(179), interfaceBInBridgeReservedList(180), invalidDlciA(181), invalidDlciB(182), unrecognizableServiceType(183), moduleAMcstNotSupported(184), moduleBMcstNotSupported(185), moduleAMultiPortMcstNotSupported(186), moduleBMultiPortMcstNotSupported(187), bcBeCirCannotBeNullA2B(188), bcBeCirCannotBeNullB2A(189), bcBeOrCirValTooHiA2B(190), bcBeOrCirValTooHiB2A(191), bcNotValidA2B(192), bcNotValidB2A(193), beNotValidA2B(194), beNotValidB2A(195), bcOrCirNotValidA2B(196), bcOrCirNotValidB2A(197), iWF-NotSupportedModuleA(198), iWF-NotSupportedModuleB(199), invalidMaxFrSizeA2B(200), invalidMaxFrSizeB2A(201), invalidSARType(202), unrecognizableSilenceDetectionModeA2B(203), unrecognizableEchoCancellationModeA2B(204), unrecognizableVoiceCompressionModeA2B(205), unrecognizableCallingToneDetectionA2B(206), unrecognizableCodingTranslationA2B(207), unrecognizableSilenceDetectionModeB2A(208), unrecognizableEchoCancellationModeB2A(209), unrecognizableVoiceCompressionModeB2A(210), unrecognizableCallingToneDetectionB2A(211), unrecognizableCodingTranslationB2A(212), dspUnsupportedForMultiCastConns(213), dspResourceUnavailable(214), destOrSrcCannotBeDSPCard(215), internalDSPResourceError(216), echoCancellationOnlySupportedForDuplex(217), cirEmCirEm-ThruPutMismatch(218), vi-Cannot-Be-0(219), vi-OOR(220), vi-Mod-Limit-Exceeded(221), vi-Resource-Unavail(222), vi-Already-Exists(223), vi-Does-Not-Exist(224), vi-0-Non-Ubr-Conn-Not-Supp(225), vi-OS-Cannot-Be-0(226), vi-OS-OOR(227), vi-CellRate-Too-Lo(228), vi-CellRate-Too-Hi(229), intf-CBR-CellRate-Exceeded(230), intf-VBR-CellRate-Exceeded(231), vi-Conn-CellRate-Exceeded(232), vi-Not-Enabled(233), vi-Should-Be-0(234), vi-OOR-A(235), vi-OOR-B(236), vi-0-Non-Ubr-Conn-Not-SuppA2B(237), vi-0-Non-Ubr-Conn-Not-SuppB2A(238), vi-Should-Be-0-A(239), vi-Should-Be-0-B(240), vi-Cbr-Bw-Unavailable-Egrs(241), vi-Cbr-Bw-Unavailable-Egrs-A(242), vi-Cbr-Bw-Unavailable-Egrs-B(243), vi-Vbr-Bw-Unavailable-Egrs(244), vi-Vbr-Bw-Unavailable-Egrs-A(245), vi-Vbr-Bw-Unavailable-Egrs-B(246), vi-Not-Enabled-A(247), vi-Not-Enabled-B(248), pcrLessThanScr(249), cnfrmTypeNotValidA2B(250), cnfrmTypeNotValidB2A(251), cnfrmType-ServiceType-Mismatch-A2B(252), cnfrmType-ServiceType-Mismatch-B2A(253), vuni-Should-Be-0(254), vuni-Not-Enabled(255), vuni-OOR(256), vuni-Already-Exists(257), vuni-Does-Not-Exist(258), vuni-Does-Not-Match-vi(259), vuni-Should-Be-0-A(260), vuni-Not-Enabled-A(261), vuni-OOR-A(262), vuni-Already-Exists-A(263), vuni-Does-Not-Exist-A(264), vuni-Does-Not-Match-vi-A(265), vuni-Should-Be-0-B(266), vuni-Not-Enabled-B(267), vuni-OOR-B(268), vuni-Already-Exists-B(269), vuni-Does-Not-Exist-B(270), vuni-Does-Not-Match-vi-B(271), vuni-Vpi-OOR(272), vuni-Vpi-OOR-A(273), vuni-Vpi-OOR-B(274), stdAal2TrunkResourceUnavailable(275), stdAal2Dsp2ResourceUnavailable(276), slotStdAal2ResourceUavailable(277), stdAal2CIDAlreadyInUse(278), stdAal2TrunkBWUavailableEgrs(279), stdAal2TrunkBWUavailableIgrs(280), stdAal2CIDInRsvRange(281), stdAal2TrunkNotSetup(282), aal2CIDOutOfRange(283), dhpvcSwitchOver-PrimToBkup(284), dhpvcSwitchOver-PrimToNone(285), dhpvcSwitchOver-NoneToPrim(286), dhpvcSwitchOver-NoneToBkup(287), dhpvcSwitchOver-BkupToNone(288), dhpvcSwitchOver-BkupToPrim(289), dhpvcState-Prim-Pass-Fail-Bkup-Act-NoFail(290), dhpvcState-Prim-Pass-NoFail-Bkup-Act-NoFail(291), dhpvcState-Prim-Act-NoFail-Bkup-Pass-Fail(292), dhpvcState-Prim-Act-NoFail-Bkup-Pass-NoFail(293), pcrGreaterThanLinkSpeedIngrA2B(294), pcrGreaterThanLinkSpeedIngrB2A(295), pcrGreaterThanLinkSpeedEgrA2B(296), pcrGreaterThanLinkSpeedEgrB2A(297), aal2CuTimerOutOfRange(298), unrecognizableDigitCollectTypeA2B(299), unrecognizableDigitCollectTypeB2A(300), queueTypeSarTypeMismatchA2B(301), queueTypeSarTypeMismatchB2A(302), pcrLessThanOrEqualToMcrA2B(303), pcrLessThanOrEqualToMcrB2A(304)

interfaceIndex		3.1.1751.2.18.15.2
Interface index used for identifcation in traps. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

interfaceType		3.1.1751.2.18.15.3
Interface type used for identification in traps. A specific interface is associated with each number. atmUni3-0(1) ATM User Network Interface version 3.0 atmUni3-1(2) ATM User Network Interface version 3.1 iispUser(3) Interim Inter Switch Protocol User Side iispNetwork(4) Interim Inter Switch Protocol Network Side circuitEmulation(5) ATM Circuit Emulation frameRelayUni(6) Frame Relay User Network Interface pri-isdn-user(7) Integrated Services Digital Network Primary Rate Interface User Interface pri-isdn-network(8) Integrated Services Digital Network Primary Rate Interface Network Interface terminalEmulation(9) Terminal Emulation dsp(10) DSP hdlcPassThrough(11) High Level Data Link Control Pass Through Interface bridge(12) Ethernet Bridge routing(13) Ethernet Routing dbCirEm(14) Dynamic Bandwidth Circuit Emulation frameRelayNni(15) Frame Relay Network Network Interface dsp2(16) DSP2 atmIma(17) ATM Inverse Multiplexing over ATM (IMA) atmPnni1-0(18) ATM Private Network Network Interface Version 1.0 atmUni4-0(19) ATM User Network Interface Version 4.0 atmVnnUni3-1(20) ATM Virtual Network Navigator User Network Interface Version 3.1 casTrunkLine(21) Channel Associated Signaling Trunk Line Interface toneAnnce(22) Tone Announcement Interface gr303(23) GR303
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	atmUni3-0(1), atmUni3-1(2), iispUser(3), iispNetwork(4), circuitEmulation(5), frameRelayUni(6), pri-isdn-user(7), pri-isdn-network(8), terminalEmulation(9), dsp(10), hdlcPassThrough(11), bridge(12), routing(13), dbCirEm(14), frameRelayNni(15), dsp2(16), atmIma(17), atmPnni1-0(18), atmUni4-0(19), atmVnnUni3-1(20), casTrunkLine(21), toneAnnce(22), gr303(23)

interfaceFailureReasonCode		3.1.1751.2.18.15.4
Identification of cause for failure in changing the status of an interface. interfaceInService(1) Most, if not all, modifications require that the interface be out of service. interfaceNotNew(2) Some modifications require that the interface must never have been in service. interfaceExists(3) Some modifications, such as setting the interface type, require that no interface exists. (type must be unconfigured). bridgeGroupActive(4) For setting the bridgeDomainNumber in bridge or router interfaces. to add an interface to a bridgeGroup, the bridgeGroup must be in service. signalingNotEnabled(5) For this interface to be created, signaling must be enabled. firmwareOutOfDate(6) The firmware for the i/o card does not work with this interface. t1SigEnableInterfaceNotSupported(7) The interface is not supported if T1 signaling is enabled ts16ForData(8) ts16 has been set for passing data and the user attempts to turn on signaling. dbcesConfigured(9) Signaling cannot be disabled because this interface is configured as dbces. signalingEnabled(10) Signaling is on for at least one of the channels while trying to change e1 TS16 from CAS to CCS. cmCardTypeNotSupported(11) CM_NET interface is only supported by DS3 DS1 OC3 and SUPER_DS1 cards cmMultipleIntfNotSupported(12) only one interface can be configured as CM_NET cmIntfInService(13) CM_NET interface is in-service cmInterfaceConfigured(14) CM_NET interface is configured channelizationEnabled(15) A port can not be channelized in order to support unstructured CE. unstructuredCEConfigured(16) A port which has been channelized can not be configured to support unstructured CE. firmwareOutOfDate-ts16CAS-unsupported(17) ts16CAS is not supported by the firmware firmwareOutOfDate-interfaceType-unsupported(18) interface type is not supported by the firmware firmwareOutOfDate-ts16-unsupported(19) ts16 is not supported by the firmware invalidPortMap(20) invalid port map otherInterfacesExistOnThisPort(21) ISDN interface needs all 24 channels on the port. If any of the channels on that interface are already configured, the ISDN interface can not be defined on that port. intfInIMAgroup(22) chanId bit in portMap is 1 errorCTC-portTxClkSrc-notLocal(23) if imaGrpChannelNeTxClkMode is set to ctc then all ports should have the transmitClockSource as localTiming different-LoopbackConfig-on-Ports(24) all physical ports included in the portMap must have the same loopback configuration imaGChanNeTxClkMode-unsupported(25) ima group channel near-end Tx clock mode is not supported intfChange-Disallowed-on-APS-ProtectionPort(26) an interface cannot be manipulated via protection port in an APS setup intferfaceCurrentlyNotSupported(27) the interface type is not support currently failure-at-call-handler(28) interface creation failure due to call handler unstructuredCE-payloadloop(29) Unstructured CE should not have payload loopback as a loop back option channelConfigModeNotConforming(30) There was a limitation on the channel mode of DSP_2D card: if there is a channel is already inService, all the channel mode of configured channels must be the same as that of the channel inService; all the channel mode of unconfigured channels can only be configured the same as that of the channel inService. usageOfReservedTimeSlot(31) for HD_E1, do not allow any configuration to be SET on channel number 1 or 17 (base 1) or chan 0 or 16 (base 0). virtualIntf-and-AtmSignaling-bothCannotBeEnabled(32) vitual interface and signalling cannot both be enabled at the same time virtualUni-and-AtmSignaling-bothCannotBeEnabled(33) vitual UNI and signalling cannot both be enabled at the same time virtualUni-notSupported(34) virtual UNI is not supported atmUni-UbrLoadBalSupp-cannotBeEnabled-whenSignalingDisabled(35) ubr load balancing cannot be enabled when signaling is disabled virtualInterface-notSupported(36) virtual interface support only allowed on APS type of cards card-doesNotSupport-UPC(37) only some cardTypes support UPC atmUni-SvcVpiVci-RangeCheck-Failure(38) Do range check provided atmSignaling is enabled vciMinSvc <= vciMaxSvc and vpiMinSvc <= vpiMaxSvc atmUni-SigVpiVci-Within-Svc-Range(39) atmUni{Vpi,Vci}Sig should not be within svc range atmUni-Ilmi-Svc-Sig-VpiVci-Clash(40) if IlmiProtocol status and atmUniSignaling are both enabled then the Ilmi Vpi/Vci should not fall in the Svc range and should not be equal to signaling vpi/vci virtualUNI-VpiNotAvailable(41) vpi is not available for the virtual UNI virtualUNI-InvalidVUNIId(42) vitural UNI Index is invalid intfNotSupported-with-ds1LineType-d4(43) if dsx1LineType is DSX1_D4 channel, interface type can't be atmIma intfNotSupported-with-ds1LineCoding-ami(44) if dsx1LineCoding is DSX1_AMI channel interface type can't be atmIma onlyCEsupported-with-msBitStuffing-enabled(45) if msBitStuffing is enabled only interface type circuit emulation is supported vISuppConnTrafficShapingMutuallyExclusive(46) The VI support flag and Traffic Shaping flag are mutually exclusive tS16onPortNotCAS(47) must have cas on port for channel to have cas trunk line interface channelizationDisabled(48) should have channelization enabled to have cas trunk line primaryDS1InterfaceNotConfigured(49) primary DS1 interface is not configured primaryTMCChanNotConfigured(50) primary timeslot management channel is not configured primaryTMCIntfAlreadyConfiguredInAnotherIg(51) primary timeslot management channel interface is already configured in another interface group primaryTMCIntfCantBeChanged(52) primary timeslot management channel interfance can't be changed primaryEOCChanNotConfigured(53) primary embeded operation channel is not configured primaryEOCIntfAlreadyConfiguredInAnotherIg(54) primary embeded operation channel interface is already configured in another interface group primaryTMC-EOCIntfShouldBeSame(55) primary timeslot management channel and embeded operation channel interfaces should be the same primaryEOCIntfCantBeChanged(56) primary embeded operation channel inteface can't be changed primaryTMC-BackupTMCIntfCantBeSame(57) primary and backup timeslot management channel interfaces can't be the same backupDS1InterfaceNotConfigured(58) backup DS1 interface is not configured backupTMCChanNotConfigured(59) backup timeslot management channel is not configured backupTMCIntfAlreadyConfiguredInAnotherIg(60) backup timeslot management channel interface is already configured in another interface group backupTMCIntfCantBeChanged(61) backup timeslot management channel interfance can't be changed primaryEOC-BackupEOCIntfCantBeSame(62) primary and backup embeded operation channel interfaces can't be the same backupEOCChanNotConfigured(63) backup embeded operation channel is not configured backupEOCIntfAlreadyConfiguredInAnotherIg(64) backup embeded operation channel interface is already configured in another interface group backupTMC-EOCIntfShouldBeSame(65) backup timeslot management channel and embeded operation channel interfaces should be the same backupEOCIntfCantBeChanged(66) backup embeded operation channel inteface can't be changed newBWBelowCurrentAllocated(67) new bandwidth is below the current allocated bandwidth newBWBelowCurrentAllocated-SvcsBeingDeleted(68) new bandwidth is below the current allocated bandwidth svc is being deleted newBWBelowCurrentAllocated-DeletePvcs(69) new bandwidth is below the current allocated bandwidth delete pvc newBWAboveCurrentAllocated(70) new bandwidth is above the current allocated bandwidth primaryInactive-or-SecondaryActive-In-IntfProtTable(71) an interface can't be deleted if it is in interface protection group which is primary/inactive or secondry/active onlyCEsupported-with-msLOSDetection-enabled(72) if msLOSDetection is enabled, only interface type circuit emulation is supported nonMuxNotAllowed-with-FaxRelay(73) DSP2 cards: if channelMode is CFG_DSP2_FAX_RELAY, aalMode can't be D_dsp2AalMode_aal2_non_multiplexed, invalid-DSPmode-and-AALmode-combination(74) DSP2 cards: such DSP mode and AAL mode combination is not allowed noBandwidth-For-SignalingConns(75) no bandwidth for signal connections
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	interfaceInService(1), interfaceNotNew(2), interfaceExists(3), bridgeGroupActive(4), signalingNotEnabled(5), firmwareOutOfDate(6), t1SigEnableInterfaceNotSupported(7), ts16ForData(8), dbcesConfigured(9), signalingEnabled(10), channelizationEnabled(15), unstructuredCEConfigured(16), firmwareOutOfDate-ts16CAS-unsupported(17), firmwareOutOfDate-interfaceType-unsupported(18), firmwareOutOfDate-ts16-unsupported(19), invalidPortMap(20), otherInterfacesExistOnThisPort(21), intfInIMAgroup(22), errorCTC-portTxClkSrc-notLocal(23), different-LoopbackConfig-on-Ports(24), imaGChanNeTxClkMode-unsupported(25), intfChange-Disallowed-on-APS-ProtectionPort(26), intferfaceCurrentlyNotSupported(27), failure-at-call-handler(28), unstructuredCE-payloadloop(29), channelConfigModeNotConforming(30), usageOfReservedTimeSlot(31), virtualIntf-and-AtmSignaling-bothCannotBeEnabled(32), virtualUni-and-AtmSignaling-bothCannotBeEnabled(33), virtualUni-notSupported(34), atmUni-UbrLoadBalSupp-cannotBeEnabled-whenSignalingDisabled(35), virtualInterface-notSupported(36), card-doesNotSupport-UPC(37), atmUni-SvcVpiVci-RangeCheck-Failure(38), atmUni-SigVpiVci-Within-Svc-Range(39), atmUni-Ilmi-Svc-Sig-VpiVci-Clash(40), virtualUNI-VpiNotAvailable(41), virtualUNI-InvalidVUNIId(42), intfNotSupported-with-ds1LineType-d4(43), intfNotSupported-with-ds1LineCoding-ami(44), onlyCEsupported-with-msBitStuffing-enabled(45), vISuppConnTrafficShapingMutuallyExclusive(46), tS16onPortNotCAS(47), channelizationDisabled(48), primaryDS1InterfaceNotConfigured(49), primaryTMCChanNotConfigured(50), primaryTMCIntfAlreadyConfiguredInAnotherIg(51), primaryTMCIntfCantBeChanged(52), primaryEOCChanNotConfigured(53), primaryEOCIntfAlreadyConfiguredInAnotherIg(54), primaryTMC-EOCIntfShouldBeSame(55), primaryEOCIntfCantBeChanged(56), primaryTMC-BackupTMCIntfCantBeSame(57), backupDS1InterfaceNotConfigured(58), backupTMCChanNotConfigured(59), backupTMCIntfAlreadyConfiguredInAnotherIg(60), backupTMCIntfCantBeChanged(61), primaryEOC-BackupEOCIntfCantBeSame(62), backupEOCChanNotConfigured(63), backupEOCIntfAlreadyConfiguredInAnotherIg(64), backupTMC-EOCIntfShouldBeSame(65), backupEOCIntfCantBeChanged(66), newBWBelowCurrentAllocated(67), newBWBelowCurrentAllocated-SvcsBeingDeleted(68), newBWBelowCurrentAllocated-DeletePvcs(69), newBWAboveCurrentAllocated(70), primaryInactive-or-SecondaryActive-In-IntfProtTable(71), onlyCEsupported-with-msLOSDetection-enabled(72), nonMuxNotAllowed-with-FaxRelay(73), invalid-DSPmode-and-AALmode-combination(74), noBandwidth-For-SignalingConns(75)

powerSupplyReasonCode		3.1.1751.2.18.15.5
Identification for change in status of a power supply. overload(1) overload overloadCleared(2) overload cleared plus5vFailed(3) +5V power supply failed plus5vCleared(4) +5V power supply cleared plus120vFailed(5) +120V power supply failed plus120vCleared(6) +120V power supply cleared minus48vFailed(7) -48V power supply failed minus48vCleared(8) -48V power supply failed
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	overload(1), overloadCleared(2), plus5vFailed(3), plus5vCleared(4), plus120vFailed(5), plus120vCleared(6), minus48vFailed(7), minus48vCleared(8)

portId		3.1.1751.2.18.15.6
Port ID used for identification in traps. Number value is interpreted as a port of the form, SSPP, where SS is the card slot and PP is the port number.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lineStatus		3.1.1751.2.18.15.7
Bit map of the status of a line connected to a port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

firmwareDownloadReasonCode		3.1.1751.2.18.15.8
The suspected reasons of why a firmware download would fail.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cardInService(1), errorInFile(2), otherFailure(3), wrongCardSubType(4), driverUnavailable(5), driverInvalidHeaderChecksum(6), driverInvalidRecordChecksum(7), requestReplyTimeout(8), completeReplyTimeout(9), mapFileCorrupted(10), mapFileUnavailable(11), mapFileInvalidChecksum(12), mapFileNameImproper(13), cfgFileCorrupted(14), cfgFileUnavailable(15), cfgFileInvalidChecksum(16), wrongCardType(17), removeCardBeforeFinish(18), ioUnsupported(19)

remoteRebootReasonCode		3.1.1751.2.18.15.9
The result of a remote reboot request.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ioCard1Reboot-OK(1), ioCard2Reboot-OK(2), ioCard3Reboot-OK(3), ioCard4Reboot-OK(4), ioCard5Reboot-OK(5), ioCard6Reboot-OK(6), ioCard7Reboot-OK(7), ioCard8Reboot-OK(8), ioCard9Reboot-OK(9), ioCard10Reboot-OK(10), ioCard11Reboot-OK(11), ioCard12Reboot-OK(12), ioCard13Reboot-OK(13), ioCard14Reboot-OK(14), ioCard15Reboot-OK(15), ioCard16Reboot-OK(16), ioCard1Reboot-NoCardInSlot(17), ioCard2Reboot-NoCardInSlot(18), ioCard3Reboot-NoCardInSlot(19), ioCard4Reboot-NoCardInSlot(20), ioCard5Reboot-NoCardInSlot(21), ioCard6Reboot-NoCardInSlot(22), ioCard7Reboot-NoCardInSlot(23), ioCard8Reboot-NoCardInSlot(24), ioCard9Reboot-NoCardInSlot(25), ioCard10Reboot-NoCardInSlot(26), ioCard11Reboot-NoCardInSlot(27), ioCard12Reboot-NoCardInSlot(28), ioCard13Reboot-NoCardInSlot(29), ioCard14Reboot-NoCardInSlot(30), ioCard15Reboot-NoCardInSlot(31), ioCard16Reboot-NoCardInSlot(32), allIOCardReboot-OK(33), allIOCardReboot-NoIOCards(34), chassisReboot-Proceeding(35), backupCpuReboot-Proceeding(36), backupCpuReboot-NoBackup(37), primaryCpuReboot-Proceeding(38), primaryCpuSwitchover-Proceeding(39), primaryCpuSwitchover-NoBackup(40), chassisReboot-Fail-VersionControlInProgress(41), backupCpuReboot-Fail-VersionControlInProgress(42), primaryCpuReboot-Fail-VersionControlInProgress(43), primaryCpuSwitchover-Fail-VersionControlInProgress(44), primaryCpuSwitchover-Fail-BkCPUDataBaseNotNew(45), primaryCpuSwitchover-Fail-BkCPUBuildNotGood(46), primaryCpuSwitchover-Fail-BkCPU-NotReady(47)

saveConfigurationReasonCode		3.1.1751.2.18.15.10
The result of a save configuration request. equipment-OK(1) - Save of equipment configuration completed. equipment-Fail-VersionControlInProgress(2) - Save of equipment configuration failed due to ongoing version control operation. equipment-Fail(3) - Save of equipment configuration failed. connections-OK(4) - Save of connection configuration completed. connections-Fail-VersionControlInProgress(5) - - Save of connection configuration failed due to ongoing version control operation. connections-Fail(6) - Save of connection configuration failed. routing-OK(7) - Save of routing configuration completed. routing-Fail-VersionControlInProgress(8) - - Save of routing configuration failed due to ongoing version control operation. routing-Fail(9) - Save of routing configuration failed. all-OK(10) - Saving of all configurations completed. all-Fail-VersionControlInProgress(11) - - Saving of all configurations failed due to ongoing version control operation. all-Fail(12) - Saving of all configurations failed. fileTransferFailed(13) - Saving of configurations to secondary CPU failed. fileTransferCompleted(14) - Saving of configurations to secondary CPU completed. unSupportedOption(15) - Unsupported save option received. fail-backupCpuInitializationInProgress(16) - - Save operation failed due to ongoing secondary cpu initialization. expect2ndCPURebootAfterSave(17) - - Notification to expect reboot of secondary CPU after a save operation. expect2ndCPUCardFailedOrRemoved(18) - Notification to expect trap indicating removal/failure of secondary CPU after a save operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	equipment-OK(1), equipment-Fail-VersionControlInProgress(2), equipment-Fail(3), connections-OK(4), connections-Fail-VersionControlInProgress(5), connections-Fail(6), routing-OK(7), routing-Fail-VersionControlInProgress(8), routing-Fail(9), all-OK(10), all-Fail-VersionControlInProgress(11), all-Fail(12), fileTransferFailed(13), fileTransferCompleted(14), unSupportedOption(15), fail-backupCpuInitializationInProgress(16), expect2ndCPURebootAfterSave(17), expect2ndCPUCardFailedOrRemoved(18)

versionConfigurationReasonCode		3.1.1751.2.18.15.11
Indicated status and results of version changing. upgrade-Start(1) upgrade starts upgrade-Completed(2) upgrade completed upgrade-Fail(3) upgrade failed downgrade-Start(4) downgrade starts downgrade-Completed(5) downgrade completed downgrade-Fail(6) downgrade failed upgrade-Fail-NoVersion(7) upgrade failed, no version upgrade-Fail-VersionControlInProgress(8) upgrade failed, version control is in progress downgrade-Fail-NoVersion(9) downgrade failed, no version downgrade-Fail-VersionControlInProgress(10) downgrade failed, version control is in progress upgrade-InProgress(11) upgrade is in progress downgrade-InProgress(12)downgrade is in progress upgrade-sanityCheck-InProgress(13) upgrade sanity check is in progress downgrade-sanityCheck-InProgress(14) downgrade sanity check is in progress upgrade-sanityCheck-Completed(15), upgrade sanity check is completed downgrade-sanityCheck-Completed(16), downgrade sanity check is completed upgrade-Fail-SanityCheckFail(17) upgrade failed due to sanity check failure downgrade-Fail-SanityCheckFail(18) downgrade failed due to sanity check failure upgrade-Fail-BkCPUFailedToRespond(19) upgrade failed since backup CPU failed to respond downgrade-Fail-BkCPUFailedToRespond(20) downgrade failed since backup CPU failed to respond upgrade-Fail-UserAbort(21) upgrade failed since user aborted downgrade-Fail-UserAbort(22) downgrade failed since user aborted synch-Start(23) synchronization starts synch-InProgress(24) synchronization is in progress synch-Completed(25) synchronization is completed synch-Fail(26) synchronization failed synch-Fail-NoBkCPU(27) synchronization failed since no backup CPU synch-Fail-SameVersion(28) synchronization failed due to the same version synch-Fail-FileCRCFailed(29) synchronization failed due to file CRC failure synch-Fail-VersionControlInProgress(30) synchronization failed since version control is in progress synch-Fail-UserAbort(31) synchronization failed since user aborted synch-Fail-SanityCheckFail(32) synchronization failed due to sanity check failure synch-Fail-BkCPUFailedToRespond(33) synchronization failed since backup CPU failed to respond synch-sanityCheck-InProgress(34) synchronization sanity check is in progress synch-sanityCheck-Completed(35) synchronization sanity check is completed failedToAbort(36) failed to abort
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	upgrade-Start(1), upgrade-Completed(2), upgrade-Fail(3), downgrade-Start(4), downgrade-Completed(5), downgrade-Fail(6), upgrade-Fail-NoVersion(7), upgrade-Fail-VersionControlInProgress(8), downgrade-Fail-NoVersion(9), downgrade-Fail-VersionControlInProgress(10), upgrade-InProgress(11), downgrade-InProgress(12), upgrade-sanityCheck-InProgress(13), downgrade-sanityCheck-InProgress(14), upgrade-sanityCheck-Completed(15), downgrade-sanityCheck-Completed(16), upgrade-Fail-SanityCheckFail(17), downgrade-Fail-SanityCheckFail(18), upgrade-Fail-BkCPUFailedToRespond(19), downgrade-Fail-BkCPUFailedToRespond(20), upgrade-Fail-UserAbort(21), downgrade-Fail-UserAbort(22), synch-Start(23), synch-InProgress(24), synch-Completed(25), synch-Fail(26), synch-Fail-NoBkCPU(27), synch-Fail-SameVersion(28), synch-Fail-FileCRCFailed(29), synch-Fail-VersionControlInProgress(30), synch-Fail-UserAbort(31), synch-Fail-SanityCheckFail(32), synch-Fail-BkCPUFailedToRespond(33), synch-sanityCheck-InProgress(34), synch-sanityCheck-Completed(35), failedToAbort(36)

percentComplete		3.1.1751.2.18.15.12
Used for trap fileTransferStatusNotify and value equals the percent of the upgrade, downgrade, or ftp download completed.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipTypeReasonCode		3.1.1751.2.18.15.13
Indicator of which ip address had the problem.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	siteEtherIpAddr(1), siteEtherIpMask(2), siteGatewayAddr(3), siteRemoteMgrAddr1(4), siteRemoteMgrAddr2(5), siteRemoteMgrAddr3(6), siteRemoteMgrAddr4(7), siteRemoteMgrAddr5(8), inBandPrimaryIpAddress(9), inBandPrimaryIpMask(10), inBandBackupIpAddress(11), inBandBackupIpMask(12), siteIncorrectGatewaySubnet(13), siteGatewayInbandAddrMatch(14), siteIncorrectInbandSubnet(15), siteIncorrectEthernetSubnet(16), cpuIpSameAsSwitchIpAddr(17), cpuIpAddrInvalid(18), cpuAndIpMaskInvalid(19), switchAndCpuIpSubnetMismatch(20), switchIpAddrInvalid(21), switchAndIpMaskInvalid(22), cpuIpMaskClashWithInbandSubnet(23), switchIpMaskClashWithInbandSubnet(24), siteGatewayAddrInvalid(25), siteGatewayInbandAddrClash(26), unableToApplyGatewayIpAddr(27), unableToSetCpuIpInEPROM(28), unableToApplyCpuIpAddr(29), unableToApplySwitchIpAddr(30), unableToRevertBackToCpuIpAddr(31), gatewayAndCpuIpSubnetMismatch(32)

timingReasonCode		3.1.1751.2.18.15.14
Indicator of type of relationship violated.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	invalidForwardDelay-MaxAge(1), invalidHelloTime-MaxAge(2)

alarmCardReasonCode		3.1.1751.2.18.15.15
Configuration status of the alarm inputs and outputs. cutoff - alarm turned off. There are two ways to turn off the audible alarm, locally via the pushbutton switch on the alarm module, and remotely, via the remote alarm cutoff, one of the alarm card inputs.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inputContactClosed(1), inputContactOpen(2), outputActivated(3), outputDactivated(4), audibleLocalAlarmEnable(5), audibleLocalAlarmCutoff(6), audibleRemoteAlarmEnable(7), audibleRemoteAlarmCutoff(8)

removeConfigFiles		3.1.1751.2.18.15.16
Used to indicate the status of a remove configuration files request. from-PrimaryCPU(1) configuration files are removed from primary CPU from-BackupCPU(2) configuration files are removed from backup CPU chassisReboot(3) chassis reboot being done after removing configuration files failed-VersionControlInProgress(4) configuration file removal failed due to ongoing version conflict
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	from-PrimaryCPU(1), from-BackupCPU(2), chassisReboot(3), failed-VersionControlInProgress(4)

spvcConfigFailureCode		3.1.1751.2.18.15.17
An identified reason for failure while configuring/modifying SPVC parameters. noSpvcConfigured(1) : There endpoint has not been configured as SPVC, so SPVC parameters cannot be modified. spvcAlreadyConfigured(2) : SPVC is already configured so it cannot be configured again as SPVC endpoint. noInterfaceConfigured(3) : There is no interface configured on the particular SSPPCCC. interfaceNotConfiguredAsRequired(4) : While configuring an SPVC endpoint, the interface is not as desired (e.g.it is not CE, while trying to configure CES SPVC). notActiveSpvc(6) : If the endpoint is configured with flowType ptToMptA2B the connType has to be activeSvc. slotA-OutofRange(7) : A-side of SPVC connection has slot number out of range. portA-OutofRange(8): A-side of SPVC connection has port number out of range. channelA-OutofRange(9): A-side of SPVC connection has channel number out of range. vpiVciWithInSvcRange(10) : A-side side of SPVC connection has vpi/vci configured in the SVC range of the A-side ATM interface. retryIntervalExceedsTheLimit(11) : retryInterval exceeds 3600s. interfaceNotConfiguredAsCE(12) : SPVC endpoint is configured as something other than CE. interfaceNotConfiguredAsVbr(13) : SPVC endpoint is configured as something other than TE. interfaceNotConfiguredAsAtm(14) : SPVC endpoint is configured as something other than ATM. noAddressConfiguredOnTheInterface(15) : Local address not configured for the particular SPVC being configured. localAddressNotValid(16) : invalid NSAP address format vpiVciUnavailable(17) : SPVC already setup on particular vpi/vci. pvcAlreadySetupOnVpiVci(18) : vpi/vci being used by another pvc. pvcAlreadySetupOnInterface(19) : redundant, same as above. interfaceNotConfiguredAsFr(21) : SPVC endpoint is configured as something other than Fr dlciUnavailable(22) : dlci not available at Passive endpoint. pvcAlreadySetupOnDlci(23) : dlci being used by another pvc. frTrafficParamsUnsupp(24) : fr-atm traffic mapping failure. dsp2ParamsUnsupp(25) : dsp2 params not supported for the call. sarNotConfigReq(26) : sarType not configured as required.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noSpvcConfigured(1), spvcAlreadyConfigured(2), noInterfaceConfigured(3), interfaceNotConfiguredAsRequired(4), notActiveSpvc(6), slotA-OutofRange(7), portA-OutofRange(8), channelA-OutofRange(9), vpiVciWithInSvcRange(10), retryIntervalExceedsTheLimit(11), interfaceNotConfiguredAsCE(12), interfaceNotConfiguredAsVbr(13), interfaceNotConfiguredAsAtm(14), noAddressConfiguredOnTheInterface(15), localAddressNotValid(16), vpiVciUnavailable(17), pvcAlreadySetupOnVpiVci(18), pvcAlreadySetupOnInterface(19), retryIntervalTooSmall(20), interfaceNotConfiguredAsFr(21), dlciUnavailable(22), pvcAlreadySetupOnDlci(23), frTrafficParamsUnsupp(24), dsp2ParamsUnsupp(25), sarNotConfigReq(26), vuniNotMatch(27)

imaGrpChannelStatus		3.1.1751.2.18.15.18
The return value for the imaGrpChannelFailNotify trap. startupFe(1) Far-end is in the state of start-up cfgAbort(2) this state is entered when the far-end tries to use unacceptable configuration parameters including invalid frame length and incompatable symmetry cfgAbortFe(3) Far-end reported unacceptable configuration parameters including invalid frame length and incompatable symmetry insuffLinks(4) Near-end reported less than the min number of Tx links are active or less than the min number of Rx links are active insuffLinksFe(5) Far-end reported less than the min number of Rx links are active or less than thenmin number of Tx links are active blockedNe(6) Near-end is administratively out-of-service blockedFe(7) Far-end is administratively out-of-service timingSynch(8) A possible configuration mismatch has occurred (CTC and CTC modes are not the same at both ends of the IMA virtual links.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	startupFe(1), cfgAbort(2), cfgAbortFe(3), insuffLinks(4), insuffLinksFe(5), blockedNe(6), blockedFe(7), timingSynch(8)

atmImaIntfStatus		3.1.1751.2.18.15.19
The return value for the atmImaIntfFailNotify trap. lif -- Persistence of LIF defect at near-end (Loss of IMA Frame) lods -- Persistence of LODS defect at near-end (Link Out of Delay Synchronization) txMisConnect -- The link is mis-connected (not connected to the same far-end as the other links in the group.) rfi -- Persistence of RDI-IMA defect at near-end (Remote Failure Indicator) fault -- Implementation specific fault at near-end txUnusableFe -- Tx link forced to unusable due to far-end behavior rxUnusableFe -- Rx link forced to unusable due to far-end behavior
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	lif(1), lods(2), txMisConnect(3), rfi(4), fault(5), txUnusableFe(6), rxUnusableFe(7)

deviceId		3.1.1751.2.18.15.20
device ID is used as the number of external devices. Each device can be an external input device or control output device.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oamTestFailureReasonCode		3.1.1751.2.18.15.21
An identified reason why an OAM Loopback Test request has failed. invalidSPCforOAM: There is no such slot/port/channel in this box. invalidIntfForOAM: There is no such interface that OAM enabled. invalidLocationLength: The length of the Loopback Lo cation ID id not valid. oamNotSupportedForThisConnection: This connection is not OAM enabled.so OAM loopback is invalid test. loopbackTestAlreadyRunning: OAM loopback is waiting for response,not expect for another test. loopbackTestNotRunning: Invalid Test Actio. oamLocalResourcesUnavailable: Memery Alloc Fail.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	invalidSPCforOAM(1), invalidIntfForOAM(2), invalidLocationLength(3), oamNotSupportedForThisConnection(4), loopbackTestAlreadyRunning(5), loopbackTestNotRunning(6), oamLocalResourcesUnavailable(7)

pnniCode		3.1.1751.2.18.15.22
An identified reason for Miscellaneous Reasons in PNNI Configuration pnniInvEndSysPortId(1) : Invalid EndSystem PortId. pnniNodeAdmStatNotUp(2) : Admin Status of Node is not up. pnniProtLnkStatDown(3) : Pnni Lnk status is down. pnniProtLnkStatUpNotAdv(4) : Pnni Lnk status up but not advertised. pnniProtLinkStatUpAdv(5) : Pnni Lnk status up and advertised. pnniIntfAdmStatUp(6) : Pnni Intf Admin Status up. pnniNodeNotCfg(7) : Pnni Node not configured in the switch. pnniRtAddrAddedByIlmi(8) : Pnni Route added succesfully from ILMI. pnniRtAddrDelByIlmi(9) : Pnni Route deleted succesfully from ILMI. pnniLvlMismatchInNodeId(10) : Level mismatch in Node Id. pnniLvlMismatchInPGId(11) : Level mismatch in Peer Group Id. pnniATMAddrInvInNodeId(12) : ATM Address entered in Node Id invalid. pnniATMAddrInvInPGId(13) : ATM Address entered in Peer Group Id invalid. pnniIntfAdmStatNotDel(14) : Pnni Intf Admin Status Not deleted. pnniNodeAdmStatUp(15) : Pnni Node Admin Status up. pnniNodeRowStatNotActive(16) : Pnni Node Row Status not active - cannot modify pnniNewRtAddrAdded(17) : New route added into pnni route address table. pnniRtAddrMod(18) : Route modified in pnni Address table. pnniAdvtNodeIdNotMine(19) : Advertised NodeId does not belong to this psax. pnniFeatureNotSupported(20) : pnni feature unsupported.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	pnniInvEndSysPortId(1), pnniNodeAdmStatNotUp(2), pnniProtLnkStatDown(3), pnniProtLnkStatUpNotAdv(4), pnniProtLinkStatUpAdv(5), pnniIntfAdmStatUp(6), pnniNodeNotCfg(7), pnniRtAddrAddedByIlmi(8), pnniRtAddrDelByIlmi(9), pnniLvlMismatchInNodeId(10), pnniLvlMismatchInPGId(11), pnniATMAddrInvInNodeId(12), pnniATMAddrInvInPGId(13), pnniIntfAdmStatNotDel(14), pnniNodeAdmStatUp(15), pnniNodeRowStatNotActive(16), pnniNewRtAddrAdded(17), pnniRtAddrMod(18), pnniAdvtNodeIdNotMine(19), pnniFeatureNotSupported(20)

swtchNodeIndx		3.1.1751.2.18.15.23
Switch Node Index for PNNI.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oc3APSPairPortIndex		3.1.1751.2.18.15.24
APS Pair Port index - SSPP
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

oc3APSReasonCode		3.1.1751.2.18.15.25
Enumerated values of the outcome of previous apsPair UserCommand or alarms on the line local - near-end remote - far-end working - working port protect - protecting port DoNotRevert - after switching from working line to protection line, don't revert to working line even it returns to work ManualSw - switch over by user command SD - signal degradation SF - signal failure Forced - force switch over LockOut - don't allow switch over to a line
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	localprotectDoNotRevert(1), localprotectManualSw(8), localprotectSD(10), localprotectSF(12), localprotectForced(14), localprotectLockOut(15), localworkingDoNotRevert(17), localworkingManualSw(24), localworkingSD(26), localworkingSF(28), localworkingForced(30), remoteprotectDoNotRevert(33), remoteprotectManualSw(40), remoteprotectSD(42), remoteprotectSF(44), remoteprotectForced(46), remoteprotectLockOut(47), noRequest(48), remoteworkingDoNotRevert(49), remoteworkingManualSw(56), remoteworkingSD(58), remoteworkingSF(60), remoteworkingForced(62)

oc3APSK1K2Rx		3.1.1751.2.18.15.26
Rx K1/K2 followed by hex value of K1, K2
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

oc3APSK1K2Tx		3.1.1751.2.18.15.27
Tx K1/K2 followed by hex value of K1, K2
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

oc3APSSelectorState		3.1.1751.2.18.15.28
Working port: active/standby Protection port: standby/active
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	w-active-p-standby(1), w-standby-p-active(2)

oc3APSWorkingLineSignalStatus		3.1.1751.2.18.15.29
Line Status of the working port sent in a trap enumeration explanations are the same as those of oc3APSProtectionLineSignalStatus
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), signalDegradation(2), signalFailure(4), lostCellDelineation(8), switchByteFailure(16), ais-l(32), ais-p(64), lop(128), lof(256), los(512), moduleFailure(1024)

oc3APSProtectionLineSignalStatus		3.1.1751.2.18.15.30
Line Status of the protection port sent in a trap. noAlarm(1) no alarm signalDegradation(2) signal bit error rate is higher than the specified threshold signalFailure(4) signal bit error rate is much higher than the specified threshold lostCellDelineation(8) unable to identify cell boundary switchByteFailure(16) switch bytes(k1,k2) of SONET header have invalid code ais-l(32) line header of SONET frame gives alarm indication signal ais-p(64) path header of SONET frame gives alarm indication signal lop(128) 1)a valid STS or VT pointer can't be obtained by using the pointer interpretation rules and the pointer word doesn't contain all-ones; 2)a number of consecutive with the NDF set to 1001 but not indicating concatenation is received lof(256) loss of frame los(512) loss of signal moduleFailure(1024) module failure
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noAlarm(1), signalDegradation(2), signalFailure(4), lostCellDelineation(8), switchByteFailure(16), ais-l(32), ais-p(64), lop(128), lof(256), los(512), moduleFailure(1024)

arpStatus		3.1.1751.2.18.15.31
Success: Arp Data is Available. Failure: Reply from RS Card timed-out. TryAgain: The request was not honoured as it came too soon (within a sec). Try again after 1 sec and we will return either Success or Noroutes.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	success(1), noArpEntries(2), tryAgain(3)

routingStatus		3.1.1751.2.18.15.32
Success: Routing Data is Available. Failure: Reply from RS Card timed-out. TryAgain: The request was not honoured as it came too soon (within a sec). Try again after 1 sec and we will return either Success or Noroutes.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	success(1), noRoutes(2), tryAgain(3)

vpnTrapStatus		3.1.1751.2.18.15.33
Return codes for route server VPN level operations. vpnAddOk(1) VPN Creation OK vpnInternalFailure(2) Memory Corruption Failure vpnTooMany(3) Exceeded Max # of VPNs vpnBadSlot(4) Impossible Slot Number vpnBadId(5) VPN ID Must Be Between 1-6 vpnBadState(6) VPN State Machine Confused vpnBadTimerVal(7) Bad Timer Value: State Machine vpnAlreadyExists(8) VPN Already Exists vpnCantLocate(9), Cannot Find Referenced VPN vpnDelInProgress(10) Deletion In Progress -Must Wait vpnLockedIdle(11) VPN Taken Out Of Service vpnGeneralFailure(12) Reference Prev.Trap For Reason vpnNotAllowed(13) Operation Not Allowed vpnShutting(14) Shutting Down VPN -Must Wait vpnDisabled(15) Some VPN SubSystem Not Working vpnModifyOk(16) Modify Operation OK
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	vpnAddOk(1), vpnInternalFailure(2), vpnTooMany(3), vpnBadSlot(4), vpnBadId(5), vpnBadState(6), vpnBadTimerVal(7), vpnAlreadyExists(8), vpnCantLocate(9), vpnDelInProgress(10), vpnLockedIdle(11), vpnGeneralFailure(12), vpnNotAllowed(13), vpnShutting(14), vpnDisabled(15), vpnModifyOk(16)

ipIntfStatus		3.1.1751.2.18.15.34
Return codes for route server IP interface operations. intOK(1) Interface OK. intIntFailure(2) Memory Corruption intTooMany(3) Exceeded Max # Of Interfaces intBadSlot(4) Impossible Slot Number intBadId(5), Impossible Interface ID intBadState(6) State Machine Confused intBadTimer(7) Bad Timer Value: State Machine intExists(8) Interface Already Exists intCantFind(9) Unused intDelInProgress(10) Deleting: -Must Wait intLockedIdle(11) Interface Taken Out Of Service intBadNetMask(12) Illegal Network Mask intShutting(13) Shutting Down -Must Wait intDisabled(14) Some Subsystem Not Working intNotHostAddr(15) Host Address Is Missing intBadIpAddr(16) Illegal IP Address intBadRouterId(17) Illegal VPN/Router ID intBadIntfId(18) Illegal Interface ID intCantFindRouter(19) No Corresponding VPN intCantFindIntf(20) Interface Does Not Exist intCantOnSameSubnet(21) Interface Already On This Subnet intCantModIntfAddr(22) Cannot Change Interface Addr intCantModIntfMask(23) Cannot Change Interface Mask intCantModIntfRipVer(24) Cannot Change Rip Ver #
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	intOK(1), intIntFailure(2), intTooMany(3), intBadSlot(4), intBadId(5), intBadState(6), intBadTimer(7), intExists(8), intCantFind(9), intDelInProgress(10), intLockedIdle(11), intBadNetMask(12), intShutting(13), intDisabled(14), intNotHostAddr(15), intBadIpAddr(16), intBadRouterId(17), intBadIntfId(18), intCantFindRouter(19), intCantFindIntf(20), intCantOnSameSubnet(21), intCantModIntfAddr(22), intCantModIntfMask(23), intCantModIntfRipVer(24)

subChanStatus		3.1.1751.2.18.15.35
Return codes for route server sub channel connections operations. scOK(1) SubChannel OK scIntFailure(2) Memory Corruption scTooMany(3) Too Many SubChannels scBadSlot(4) Impossible Slot Number scBadId(5) Bad VPN ID scBadState(6), State Machine Confusion scBadTimerVal(7) Bad Timer Value: State Machine scExists(8) SubChannel Already Exists scCantFind(9) Unused scDelInProgress(10) Deleting: -Must Wait scLockedIdle(12) SubChannel Taken Out Of Serv. scSameVc(13) Connection In Use Already scFailedSetup(14) Referene Previous Trap scShutting(15) Shutting Down: -Must Wait scDisabled(16) SubSystem Disabled. scSetupErr(17) scRemvErr(18) Error Removing SubChannel scBadPortNo(19) Bad Port Specified scBadImIpAddr(20) Bad InBand IP Address scBadRouterId(21) Bad VPN/Router ID scBadIntfId(22) Impossible Interface ID scBadChanId(23) Impossible Channel ID scCantFindRouter(24) Cannot Find VPN scCantFindIntf(25) Cannot Find Interface scCantFindChan(26) Cannot Find SubChannel
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	scOK(1), scIntFailure(2), scTooMany(3), scBadSlot(4), scBadId(5), scBadState(6), scBadTimerVal(7), scExists(8), scCantFind(9), scDelInProgress(10), scLockedIdle(12), scSameVc(13), scFailedSetup(14), scShutting(15), scDisabled(16), scSetupErr(17), scRemvErr(18), scBadPortNo(19), scBadImIpAddr(20), scBadRouterId(21), scBadIntfId(22), scBadChanId(23), scCantFindRouter(24), scCantFindIntf(25), scCantFindChan(26)

routeSrvStatus		3.1.1751.2.18.15.36
Return codes for basic route server task operations not related to any specific VPN or IP/Connection operation. rsCardOK(1) Route Server OK rsModInitFail(2) Route Server Failed Module Init. rsIntfInitFail(3) Route Server Failed Intf. Init. rsPortInitFail(4) Route Server Failed Port Init rsRipUpdateIntOK(5) Rip Update Interval was updated ok for the route server card. rsRipUpdateIntFail(6) Rip Update Interval was not updated mostly because of some VPN's still in service.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rsCardOK(1), rsModInitFail(2), rsIntfInitFail(3), rsPortInitFail(4), rsRipUpdateIntOK(5), rsRipUpdateIntFail(6)

apsFailureReasonCode		3.1.1751.2.18.15.37
Identification of cause for automatic protection switching failure. protectionCard-notPresent(1) protection card doesn't exist protectionCardType-notAPS(2) card type of protection card is not APS protectionCardType-incompatible(3) card types of protection card and working card are incompatible protectionCard-notInUnconfiguredState(4) protection card is already configured protectionCard-notUnprotected(5) protection card is not unprotected resource-access-failure(6) internal failure application incorrect-APSconfiguration(7) correct aps configuration: 1)oc3APSConfiguration of working port is working and oc3APSConfiguration of protection port is protection 2) oc3APSConfiguration of working and protection ports are unprotected protectionPort-Active(8) protection port must be inactive when breaking aps pair workingPort-localLoop-notAllowed(9) working port can't be configured as localLoop protectionPort-localLoop-notAllowed(10) protection port can't be configured as localLoop either
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	protectionCard-notPresent(1), protectionCardType-notAPS(2), protectionCardType-incompatible(3), protectionCard-notInUnconfiguredState(4), protectionCard-notUnprotected(5), resource-access-failure(6), incorrect-APSconfiguration(7), protectionPort-Active(8), workingPort-localLoop-notAllowed(9), protectionPort-localLoop-notAllowed(10)

statRtStatus		3.1.1751.2.18.15.38
Return codes for route server static route condititions. statRtOk(1) Static Rt OK statRtIntFailure(2) Memory Corruption statRtMany(3) Too Many Static Routes statRtSlot(4) Impossible Slot ID statRtBadId(5) Bad VPN ID statRtBadState(6) State Machine Confusion statRtBadTimer(7) Bad Timer Value: State Machine statRtExists(8) Static Rt Already Exists statRtCantFind(9) Unused statRtDelInProgress(10) Deleting: -Must Wait statRtLockedIdle(11) Static Rt Taken Out Of Service statRtBadNetMask(12) Bad Network Mask statRtCorrelation(13) Internal Correlation Error statRtShutting(14) Shutting Down: -Must Wait statRtDisabled(15) SubSystem Failure statRtBadMetric(16) Illegal Metric Value statRtBadIPAddr(17) Bad Static Route IP Address intfRtExists(18) Static Route On Different Intf. statRtBadSlot(19) Impossible Slot ID statRtBadRouterId(20) Bad VPN/Router ID statRtBadRouteId(21) Illegal Static Route ID statRtBadRouteNetMask(22) Bad Stat Route Network Mask statRtBadRouteIpAddr(23) Bad Interface IP Address statRtBadGtwyIpAddr(24) Bad Gateway IP Address statRtBadDestIpAddr(25) Bad Destination IP Address statRtBadDestNetMask(26) Bad Destination IP Mask statRtCantFindRouter(27) Cannot Find VPN statRtCantFindRoute(28) Cannot Find Static Route
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	statRtOk(1), statRtIntFailure(2), statRtMany(3), statRtSlot(4), statRtBadId(5), statRtBadState(6), statRtBadTimer(7), statRtExists(8), statRtCantFind(9), statRtDelInProgress(10), statRtLockedIdle(11), statRtBadNetMask(12), statRtCorrelation(13), statRtShutting(14), statRtDisabled(15), statRtBadMetric(16), statRtBadIPAddr(17), intfRtExists(18), statRtBadSlot(19), statRtBadRouterId(20), statRtBadRouteId(21), statRtBadRouteNetMask(22), statRtBadRouteIpAddr(23), statRtBadGtwyIpAddr(24), statRtBadDestIpAddr(25), statRtBadDestNetMask(26), statRtCantFindRouter(27), statRtCantFindRoute(28)

portFailureReasonCode		3.1.1751.2.18.15.39
Identification of cause for failure in changing the parameters of a port insufficientModuleBandwidth(1) insufficient module bandwidth localLoopNotAllowedWhenInAPS(2) local loop is not allowed when a port is in an automatic switching pair. msBitStuffingEnabledOnlyForCE(3) if msBitStuffing is enabled, only interface type circuit emulation is allowed invalidOption(4) invalid option hasInterfaceInService(5) interface is in-service unsupportedBaudRate(6) the baud rate is not supported msLOSDetectionNotEnabled(7) msLOSDetection is not enabled
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	insufficientModuleBandwidth(1), localLoopNotAllowedWhenInAPS(2), msBitStuffingEnabledOnlyForCE(3), invalidOption(4), hasInterfaceInService(5), unsupportedBaudRate(6), msLOSDetectionNotEnabled(7)

dlciNumber		3.1.1751.2.18.15.40
The number of the dlci being used.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipAddrNumber		3.1.1751.2.18.15.41
The IP address of the host/network to be echoed
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

pingStatusReasonCode		3.1.1751.2.18.15.42
The response value - Alive destination can be reached Not Alive destination can't be reached
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	alive(1), not-Alive(2)

primarySoftwareVersion		3.1.1751.2.18.15.43
Software version running on primary cpu.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(20)

backupSoftwareVersion		3.1.1751.2.18.15.44
Software version running on backup cpu.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(20)

oamActDeactResultCode		3.1.1751.2.18.15.45
Various result codes for the operator's command for OAM Activation-Deactivation. eteCCActSuccTowardsFarEnd: eteCCActSuccTowardsNearEnd: eteCCActSuccTowardsBothEnd: eteCCDeactSuccTowardsFarEnd: eteCCDeactSuccTowardsNearEnd: eteCCDeactSuccTowardsBothEnd: ete CC Act/Deact-request send out to far/near/both end eteCCActDeniedTowardsFarEnd: eteCCActDeniedTowardsNearEnd: eteCCActDeniedTowardsBothEnd: eteCCDeactDeniedTowardsFarEnd: eteCCDeactDeniedTowardsNearEnd: eteCCDeactDeniedTowardsBothEnd: ete CC Act/Deact-request is denied. eteCCActFailedTowardsFarEnd: eteCCActFailedTowardsNearEnd: eteCCActFailedTowardsBothEnd: eteCCDeactFailedTowardsFarEnd: eteCCDeactFailedTowardsNearEnd: eteCCDeactFailedTowardsBothEnd: ete CC Act/Deact-request is failed sent out segCCActSuccTowardsFarEnd: segCCActSuccTowardsNearEnd: segCCActSuccTowardsBothEnd: segCCDeactSuccTowardsFarEnd: segCCDeactSuccTowardsNearEnd: segCCDeactSuccTowardsBothEnd: segment CC Act/Deact-request send out to far/near/both end. segCCActDeniedTowardsFarEnd: segCCActDeniedTowardsNearEnd: segCCActDeniedTowardsBothEnd: segment CC Act-request is denied. segCCActFailedTowardsFarEnd: segCCActFailedTowardsNearEnd: segCCActFailedTowardsBothEnd: ete CC Act-request is failed sent out. oamReqFunctionNotImplemented: The function user issued is not impemeted. oamActDeactPrevReqInProgress: this interface is in wait for response state. SendPMCell: a management cell has been sent out to IO card indicating PM cell need to be sent. eteReceiveBRErrMessage: a BR message has been forwarded to CPU indicating BR error. receiveFPMErrMessage: a FPM message has been forwarded to CPU indicating FPM error.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eteCCActSuccTowardsFarEnd(1), eteCCActSuccTowardsNearEnd(2), eteCCActSuccTowardsBothEnd(3), eteCCActDeniedTowardsFarEnd(4), eteCCActDeniedTowardsNearEnd(5), eteCCActDeniedTowardsBothEnd(6), eteCCActFailedTowardsFarEnd(7), eteCCActFailedTowardsNearEnd(8), eteCCActFailedTowardsBothEnd(9), eteCCDeactSuccTowardsFarEnd(10), eteCCDeactSuccTowardsNearEnd(11), eteCCDeactSuccTowardsBothEnd(12), eteCCDeactDeniedTowardsFarEnd(13), eteCCDeactDeniedTowardsNearEnd(14), eteCCDeactDeniedTowardsBothEnd(15), eteCCDeactFailedTowardsFarEnd(16), eteCCDeactFailedTowardsNearEnd(17), eteCCDeactFailedTowardsBothEnd(18), segCCActSuccTowardsFarEnd(19), segCCActSuccTowardsNearEnd(20), segCCActSuccTowardsBothEnd(21), segCCActDeniedTowardsFarEnd(22), segCCActDeniedTowardsNearEnd(23), segCCActDeniedTowardsBothEnd(24), segCCActFailedTowardsFarEnd(25), segCCActFailedTowardsNearEnd(26), segCCActFailedTowardsBothEnd(27), segCCDeactSuccTowardsFarEnd(28), segCCDeactSuccTowardsNearEnd(29), segCCDeactSuccTowardsBothEnd(30), oamReqFunctionNotImplemented(31), oamReqFailLocRsrcUnavl(32), oamActDeactPrevReqInProgress(33), oamActDeactInvalidParams(34), oamActDeactInvalidIntf(35), oamNotSupportedForThisConnection(36), oamCCnotSupportedForThisConnection(37), oamPrevActDeactReqFailed(38), oamEteLossOfContinuitySet(39), oamEteLossOfContinuityCleared(40), oamSegLossOfContinuitySet(41), oamSegLossOfContinuityCleared(42), oamActDeactPMOnlySupportOC3(43), oamPMnotSupportedForThisConnection(44), oamPMBRnotSupportedForThisConnection(45), etePMActSuccTowardsFarEnd(46), etePMActSuccTowardsNearEnd(47), etePMActSuccTowardsBothEnd(48), etePMActDeniedTowardsFarEnd(49), etePMActDeniedTowardsNearEnd(50), etePMActDeniedTowardsBothEnd(51), etePMActFailedTowardsFarEnd(52), etePMActFailedTowardsNearEnd(53), etePMActFailedTowardsBothEnd(54), etePMDeactSuccTowardsFarEnd(55), etePMDeactSuccTowardsNearEnd(56), etePMDeactSuccTowardsBothEnd(57), etePMBRActSuccTowardsFarEnd(58), etePMBRActSuccTowardsNearEnd(59), etePMBRActSuccTowardsBothEnd(60), etePMBRActDeniedTowardsFarEnd(61), etePMBRActDeniedTowardsNearEnd(62), etePMBRActDeniedTowardsBothEnd(63), etePMBRActFailedTowardsFarEnd(64), etePMBRActFailedTowardsNearEnd(65), etePMBRActFailedTowardsBothEnd(66), etePMBRDeactSuccTowardsFarEnd(67), etePMBRDeactSuccTowardsNearEnd(68), etePMBRDeactSuccTowardsBothEnd(69), segPMActSuccTowardsFarEnd(70), segPMActSuccTowardsNearEnd(71), segPMActSuccTowardsBothEnd(72), segPMActDeniedTowardsFarEnd(73), segPMActDeniedTowardsNearEnd(74), segPMActDeniedTowardsBothEnd(75), segPMActFailedTowardsFarEnd(76), segPMActFailedTowardsNearEnd(77), segPMActFailedTowardsBothEnd(78), segPMDeactSuccTowardsFarEnd(79), segPMDeactSuccTowardsNearEnd(80), segPMDeactSuccTowardsBothEnd(81), segPMBRActSuccTowardsFarEnd(82), segPMBRActSuccTowardsNearEnd(83), segPMBRActSuccTowardsBothEnd(84), segPMBRActDeniedTowardsFarEnd(85), segPMBRActDeniedTowardsNearEnd(86), segPMBRActDeniedTowardsBothEnd(87), segPMBRActFailedTowardsFarEnd(88), segPMBRActFailedTowardsNearEnd(89), segPMBRActFailedTowardsBothEnd(90), segPMBRDeactSuccTowardsFarEnd(91), segPMBRDeactSuccTowardsNearEnd(92), segPMBRDeactSuccTowardsBothEnd(93), eteSendPMCell(94), eteReceiveBRErrMessage(95), receiveBRErrMessage(96), receiveFPMErrMessage(97), sendPMCell(98)

tasCmprsAnnceReasonCode		3.1.1751.2.18.15.46
The result of a compress announcement request.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cmprs-success(1), cmprs-Fail-equipment-Fail(2), cmprs-Fail-connections-Fail(3), cmprs-Fail-resource-busy(4), cmprs-Fail-resource-unavail(5)

tasTstLineReasonCode		3.1.1751.2.18.15.47
The result of a test line request.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	tst-success(1), tst-Fail-equipment-Fail(2), tst-Fail-invalid-params(3), tst-Fail-resource-unavail(4), tst-Fail-resource-busy(5)

gr303PPSReasonCode		3.1.1751.2.18.15.48
These reason codes are the result of GR303 Path Protection Switching (PPS) command issued by user
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	forced(1), normal(2), userCommandFailed-inhibited(3), userCommandFailed-PathOos(4), userCommandFailed-badPathId(5), userCommandFailed-maxRetry(6), userCommandFailed-inprogress(7), userCommandFailed-unknown(8)

gr303PPSSource		3.1.1751.2.18.15.49
Indicates the initiator of the PPS switching
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), byIdt(2), byUser(3), byLocalAgent(4), suspendedByIdt(5), suspendedByLocalAgent(6)

tasMemReasonCode		3.1.1751.2.18.15.50
The result of a memory init request.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	mem-init-success(1), mem-init-Fail(2)

tasTrapTstId		3.1.1751.2.18.15.51
Announcement ID for trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..100

tasTrapAnnceId		3.1.1751.2.18.15.52
test id for trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..100

atmVpi		3.1.1751.2.18.15.53
Vpi is used in identification of Traps
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

atmVci		3.1.1751.2.18.15.54
Vci is used in identification of Traps
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

iptResultCode		3.1.1751.2.18.15.55
Various result codes for the operator's command forsetting/deleting interface protection group. interfaceProtectioniptAlreadyExistInterface: Expect another interface to be protected. interfaceProtectioniptInvalidInterface:interface invalid interfaceProtectioniptInvalidParams: invalid Parameters interfaceProtectioniptTryToDeleteEmptyTable:Table is already empty,can not be deleted . interfaceProtectioniptInvalidConfiguation: interfaceProtectioniptSuccessfulSwichOver: interface is switched over to the secondry interface. interfaceProtectioniptSuccessfulSwichBack: interface is switched back from secondry interface. interfaceProtectioniptFailedSwichOver: interface is failed switched over to the secondry interface. interfaceProtectioniptFailedSwichBack: interface is failed switched back from secondry interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	interfaceProtectioniptAlreadyExistInterface(1), interfaceProtectioniptInvalidInterface(2), interfaceProtectioniptInvalidParams(3), interfaceProtectioniptTryToDeleteEmptyTable(4), interfaceProtectioniptInvalidConfiguation(5), interfaceProtectioniptSuccessfulSwichOver(6), interfaceProtectioniptSuccessfulSwichBack(7), interfaceProtectioniptFailedSwichOver(8), interfaceProtectioniptFailedSwichBack(9)

pgtResultCode		3.1.1751.2.18.15.56
Various result codes for the operator's command for interface protection .
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	interfaceProtectionpgtAlreadyExistInterface(1), interfaceProtectionpgtInvalidInterface(2), interfaceProtectionpgtInvalidParams(3), interfaceProtectionpgtryToDeleteEmptyTable(4), interfaceProtectionpgtSuccessfulSwichOver(5), interfaceProtectionpgtSuccessfulSwichBack(6), interfaceProtectionpgtFailedSwichOver(7), interfaceProtectionpgtFailedSwichBack(8), interfaceProtectionpgtInvalidConfiguation(9)

tasmControlBlockAllocFailReasonCode		3.1.1751.2.18.15.57
The result of a tasm control block memory allocation request.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	res-alloc-success(1), res-alloc-Fail-announce-control-blocks-mem-unavail(2), res-alloc-Fail-digit-control-blocks-mem-unavail(3), res-alloc-Fail-line-test-control-blocks-mem-unavail(4)

tasmCacheMemAllocFailReasonCode		3.1.1751.2.18.15.58
The result of a tasm control block memory allocation request.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	res-alloc-success(1), res-alloc-Fail-announce-cache-mem-unavail(2)

atmTrunkingConfigFailureCode		3.1.1751.2.18.15.59
An identified reason for failure while configuring/modifying ATM Trunking parameters: localIWFAlreadyConfigured(1) : Local IWF has already been configured, the parameters can not be changed or apply again. localIWFAtmAddressError(2): the ATM Address for Local IWF is not valid or this address has been used by someone else. localIWFIdOutOfRange(3): the Identification of Local IWF is out of range. maxNumberRmtIWFOutOfRange(4): the maximum number of Remote IWF is out of range. rmtIWFAlreadyConfigured(5): this remote IWF has already been configured( with index atmTrunkingRmtIWFIdentifier). rmtIWFIdOutOfRange: the identifier for the remote IWF is out of range. rmtIWFAtmAddressError: the ATM Address for remote IWF is not valid or this address has been used by someone else. vccIdError: the VCC ID for the SigVcc or BrVcc is 0, or this VCC ID is out of range or it has been used by someone else. vccPvcParameterNotAcceptable: the parameters of PVC side, including slot, port, channel, vpi, vci, are not acceptable. vccTrafficParameterNotValid: the VCC traffic parameters are not acceptable, including FwPcr01, BwPcr01, FwScr01, BwScr01, FWMbs01, BwMbs01, BrVccServiceType, BrVccSarType. vccViVuniNotValid: the configuration of Egress Vi/VUNI is not acceptable. vccTrunkParameterNotValid: the parameters for the Trunk is not supported, including BrVccMaxAal2ChanId, BrVccCircuitModeDataSupp, BrVccFrameModeSupp, BrVccFaxModeSupp, CASPktXportSupp, BrVccDTMFPktXportSupp, BrVccMFR1PktXportSupp, BrVccMFR2PktXportSupp, BrVccPCMEncoding, BrVccMaxFrameLength, BrVccIdleChannSuprSupp, BrVccSilenceDetSupp, BrVccCompressionSpec,AudioProfileId, SigVccSignaling. vccTrunkFeatureParameterNotValid: PSAX proprietary feature parameters not supported including SigVccInactiveTimer, SigVccRetryTimer, SigVccRetryLimit, BrVccInactiveTimer, BrVccRetryTimer, BrVccRetryLimit, BrVccGr303Supp, BrVccOamStatus. localIwfNotConfigured(14) : Local IWF not Configured localIwfIdNotMatch(15): specified Local IWF not match localIwfStatus(16): this operation is not supported because of the status of Local IWF rmtIwfNotConfigured(17): Remote IWF Not Configured rmtIwfModeNotCompatible(18): the Mode of Remote IWF is not compatiable rmtIwfStatus(19): this operation is not support because of the Status of Remote IWF vccAlreadyConfigured(20): This VCC has been configured vccPvcCacReject(21): PVC Configuration rejected by Cac Reservation Function requiredFieldMissing(22): mandatory fields missing outOfResource(23): Atm Trunking Task or System out of resource for this configuration rowStatusError(24):Row Status Error with the SNMP command generalErrorUnspecified(25): all other unspecified failure cause.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	localIWFAlreadyConfigured(1), localIWFAtmAddressError(2), localIWFIdOutOfRange(3), maxNumberRmtIWFOutOfRange(4), rmtIWFAlreadyConfigured(5), rmtIWFIdOutOfRange(6), rmtIWFAtmAddressError(7), vccIdError(8), vccPvcParameterNotAcceptable(9), vccTrafficParameterNotValid(10), vccViVuniNotValid(11), vccTrunkParameterNotValid(12), vccTrunkFeatureParameterNotValid(13), localIwfNotConfigured(14), localIwfIdNotMatch(15), localIwfStatus(16), rmtIwfNotConfigured(17), rmtIwfModeNotCompatible(18), rmtIwfStatus(19), vccAlreadyConfigured(20), vccPvcCacReject(21), requiredFieldMissing(22), outOfResource(23), rowStatusError(24), generalErrorUnspecified(25)

sapphireIntfAddressFailReasonCode		3.1.1751.2.18.15.60
The result of assigning the Sapphire Interface address when PSAX is Sapphire client. address-ok(1), Address assignment succeeded fail-Ilegal-IP-address(2), Illegal IP address assigned address not matching fail-not-match-InBandManagement-Switch-CPU-IP-Address(3) In-Band Management IP or Switch IP or CPU IP address fail-Switch-or-CPU-IP-Address-unconfigured(4) Switch IP or CPU IP address unconfigured fail-InBandManagement-IP-Address-unconfigured(5) InBandManagement IP address unconfigured.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	address-assign-ok(1), fail-Ilegal-IP-address(2), fail-not-match-InBandManagement-Switch-Cpu-IP-Address(3), fail-Switch-or-Cpu-IP-Address-unconfigured(4), fail-InBandManagement-IP-Address-unconfigured(5)

chassisOverTempAlarmReasonCode		3.1.1751.2.18.15.61
Indicator of presence of chassis over temperature alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	set(1), clear(2)

saveConfiguration		3.1.1751.2.18.16.1
save configuration
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	equipment(1), connections(2), routing(3), all(4)

upgradeSoftware		3.1.1751.2.18.16.2
software load management
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	upgrade(1), fallBack(2), forceUpgrade(3), forceFallBack(4), synchronize(5), abort(6), forceSynchronize(7), forceAbort(8)

purgePvcConnections		3.1.1751.2.18.16.3
purge PVC connections on indicated interface
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

purgeRoutingTable		3.1.1751.2.18.16.4
purge indicated routing table
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	iispCbr(1), iispVbr(2)

resetPortStatistics		3.1.1751.2.18.16.5
Reset the statistics counters for the given port Id (SSPP)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

resetInterfaceStatistics		3.1.1751.2.18.16.6
Reset the interface counters for the given port Id (SSPPCCC)
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

resetAllStatistics		3.1.1751.2.18.16.7
Reset all port and interface statistics counters, accpets any integer value
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

upgradeIpAddress		3.1.1751.2.18.16.8
IP Address for upgrade ftp server.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

upgradeAccountName		3.1.1751.2.18.16.9
ftp account name for access to upgrade ftp server.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

upgradeAccountPassword		3.1.1751.2.18.16.10
ftp account password for access to upgrade ftp server.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

upgradeCdromFile		3.1.1751.2.18.16.11
cdrom file path on upgrade ftp server to upgrade image library.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(79)

upgradeLicenseKey		3.1.1751.2.18.16.12
software license key.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(30)

upgradeSwCopyStatus		3.1.1751.2.18.16.13
Current status of the ftp software upgrade download. Status of the software upgrade. noActivity is the initial start state from boot-up. working is set while ftp'ing the upgrade. The final state is one of doneSuccessfully, doneWithError, or aborted, all self-explanatory. It will stay in this state until re-boot or starting an upgrade. If the state is doneWithError then upgradeSwErrorStatus will be set to reflect the type of error.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noActivity(1), working(2), doneSuccessfully(3), doneWithError(4), aborted(5)

upgradeSwErrorStatus		3.1.1751.2.18.16.14
The result of the finish of the ftp software upgrade download. Set to a value 3-22 if upgradeSwCopyStatus is doneWithError. Set to none if upgradeSwCopyStatus is doneSuccessfully. Set to userAbort if upgradeSwCopyStatus is aborted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), userAbort(2), invalidIpAddress(3), invalidAccountName(4), invalidAccountPassword(5), invalidCdromFile(6), libraryCRCFail(7), unableToOpenLibraryFile(8), unableToLoadLibraryModule(9), unableToFindTaskSymbolName(10), failureInSpawningTask(11), failureInCreatingMsgQ(12), failureInCopyingDataFiles(13), failureToRemoveNextTree(14), unableToMakeNextTree(15), unableToOpenFile(16), unableToMakeFtpConnection(17), unableToWriteFile(18), unableToCompleteFtp(19), fileCRCFail(20), unableToWritePackageList(21), taskSuspendOrDead(22), unableToUpdateBackup(23), cpuAbort(24), failureToTakeSemaphore(25), failureToRemoveFallBackTree(26), unableToMakeFallBackTree(27)

systemSwCopy		3.1.1751.2.18.16.15
start copy system files according to the profile. When upgradeSwCopyStatus is working, the start request will be ignored. Abort will have effect only when upgradeSwCopystatus is working.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	start(1), abort(2)

fwReleaseTable		3.1.1751.2.18.16.16
Table of firmware inventory data
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FwReleaseEntry

fwReleaseEntry		3.1.1751.2.18.16.16.1
Row definition for firmware inventory
Status: current	Access: not-accessible
OBJECT-TYPE
	FwReleaseEntry

fwReleaseSlot		3.1.1751.2.18.16.16.1.1
Physical slot location. Valid range is a number between 1 and 16.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..16

fwReleaseRunning		3.1.1751.2.18.16.16.1.2
the firmware release currently running in a physical slot (e.g., 01.03.C01).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(15)

fwReleaseEpromVersion		3.1.1751.2.18.16.16.1.3
the version of the firmware located on the I/O card (e.g., 01.03.C01).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(9)

fwReleaseCurrentVersion		3.1.1751.2.18.16.16.1.4
the version of the firmware located in /scsi/current/io on the CPU disk drive (e.g., 01.03.C01).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(9)

fwReleaseNextVersion		3.1.1751.2.18.16.16.1.5
the version of the firmware located in /scsi/next/io on the CPU disk drive (e.g., 01.03.C01).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(9)

fwReleaseUpdate		3.1.1751.2.18.16.16.1.6
Update the fwReleaseCurrentVersion and the fwReleaseNextVersion variables by remapping the firmware files from the CPU disk drive.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	activate(1)

fwReleaseUpgrade		3.1.1751.2.18.16.16.1.7
Update the fwReleaseCurrentVersion and the fwReleaseNextVersion variables by remapping the firmware files from the CPU disk drive.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eprom(1), current(2), next(3)

resetBridgeDomainStatistics		3.1.1751.2.18.16.17
Resets bridge domain statistics.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

remoteRebootCommand		3.1.1751.2.18.16.18
type of reboot.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ioCard1Reboot(1), ioCard2Reboot(2), ioCard3Reboot(3), ioCard4Reboot(4), ioCard5Reboot(5), ioCard6Reboot(6), ioCard7Reboot(7), ioCard8Reboot(8), ioCard9Reboot(9), ioCard10Reboot(10), ioCard11Reboot(11), ioCard12Reboot(12), ioCard13Reboot(13), ioCard14Reboot(14), ioCard15Reboot(15), ioCard16Reboot(16), allIOCardReboot(100), chassisReboot(101), backupCpuReboot(102), primaryCpuReboot(103), primaryCpuSwitchover(200)

resetFrLmiStatistics		3.1.1751.2.18.16.19
Reset the frame relay LMI statistics counters for the given port Id (SSPPCCC)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

removeConfigurationFiles		3.1.1751.2.18.16.20
Removes the user configuration/connection files from the hard disk on the cpu.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	all(1)

systemFilesDirtyBitStatus		3.1.1751.2.18.16.21
Bit mask for system files: 0: all are clean 1: console.def 2: ecd.def 4: ssid.def 8: cnctn.db 16: iisp.cbr 32: iisp.vbr 64: spvc.db 128: vipr.cfg 256: fwc.def 512: vi.db 1024: iproute.db 2048: atmvuni.db
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4096

resetAtmIlmiStatistics		3.1.1751.2.18.16.22
Reset the ATM ILMI statistics counters for the given channel Id (SSPPCCC)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

resetImaGrpChannelStatistics		3.1.1751.2.18.16.23
Reset the IMA Group Statistics counters for the given port Id (SSPPCCC)
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

oc3APSResetStats		3.1.1751.2.18.16.24
Reset the oc3aps Group Statistics counters for the given port Id (SSPP)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

resetsonetSectionStatistics		3.1.1751.2.18.16.25
Reset the sonetSectionCurrent Statistics counters for the given port Id (SSPP)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

resetsonetLineStatistics		3.1.1751.2.18.16.26
Reset the sonetLineCurrent Statistics counters for the given port Id (SSPP)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

resetsonetVTPathStatistics		3.1.1751.2.18.16.27
Reset the sonetVTPathCurrent Statistics counters for the given port Id (SSPP)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprVpnReset		3.1.1751.2.18.16.28
Reset the VPN statistics for VPN specified by (SSVV)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

svcRetBackupStatus		3.1.1751.2.18.16.29
Indicates backup status wrt SVC retention
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no-sync(1), sync-in-progress(2), fully-sync(3)

resetsonetPathStatistics		3.1.1751.2.18.16.30
Reset the sonetPathCurrent Statistics counters for the given port Id (SSPP)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ambientTemperature		3.1.1751.2.18.16.31
Ambient temperature in degree Celcius where the system is kept
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

remoteDbServerGroup		3.1.1751.2.18.16.32
OBJECT IDENTIFIER

remoteDbServerIpAddress		3.1.1751.2.18.16.32.1
IP Address for remote database server.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

remoteDbServerLogin		3.1.1751.2.18.16.32.2
ftp account name for remote database server.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

remoteDbServerPassword		3.1.1751.2.18.16.32.3
ftp account password for remote database server.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

remoteDbServerDirectory		3.1.1751.2.18.16.32.4
directory on remote database server where to save/restore database files from.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(79)

remoteDbCommand		3.1.1751.2.18.16.32.5
remote database operation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noOperation(1), remoteSave(2), remoteLoad(3)

remoteDbOperationStatus		3.1.1751.2.18.16.32.6
Current status of remote database command.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noActivity(1), working(2), doneSuccessfully(3), doneWithError(4), aborted(5)

remoteDbOperationErrorStatus		3.1.1751.2.18.16.32.7
The result at the finish of remote database operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), unableToMakeFtpConnection(1), invalidDirectory(2), unableToOpenDatabaseFile(3), unableToCompleteFtp(4), databaseSanityFail(5), unableToUpdateBackup(6)

stratumSyncSource		3.1.1751.2.18.17.1
Clock source for the stratum card - lineTiming: must have slot and port specified in stratumPrimaryLineId. compositeClock: local clock must be available.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	lineTiming(1), compositeClock(2), freerun(3), t1BITS(4), e1ETSI(5)

stratumPrimaryLineId		3.1.1751.2.18.17.2
Format SSPP (slot and port #'s) to be used when lineTiming is specified in stratumSyncSource.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

stratumSecondaryLineId		3.1.1751.2.18.17.3
Format SSPP (slot and port #'s) to be used if the primary line has failed. Zeros imply that the stratum should switch to holdover mode instead.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

stratumLevel		3.1.1751.2.18.17.4
Enable or disable the switching over to stratum 4 when stratum 3 is not possible.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	stratum3(1), stratum4(2)

stratumLineCommand		3.1.1751.2.18.17.5
Forces the stratum card to use one of the two specified lines as its clock source when the stratumSyncSource is lineTiming.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	gotoPrimaryLine(1), gotoSecondaryLine(2)

stratumLineTimingStatus		3.1.1751.2.18.17.6
Represents the source of the current clock.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primaryLine(1), secondaryLine(2), none(3)

stratumMode		3.1.1751.2.18.17.7
Current status of the primary stratum card. synchronized3(1) stratum is synchronized with accuracy 4.6 x 10e-6 synchronized4(2) stratum is synchronized with accuracy 3.2 x 10e-5 holdover(3) an operating condition of a clock that has lost its controlling input and is using stored data acquired while in normal operation, to control its output freerun(4) an operating condition of the clock whose output signals are internally controlled cardRemoved(5) stratum removed
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	synchronized3(1), synchronized4(2), holdover(3), freerun(4), cardRemoved(5)

stratumBackupMode		3.1.1751.2.18.17.8
Current status of the backup stratum card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	synchronized3(1), synchronized4(2), holdover(3), freerun(4), cardRemoved(5)

stratumRefFailAction		3.1.1751.2.18.17.9
Defines whether the stratum should switch to freerun or holdover on reference clock failure.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	holdover(1), freerun(2)

stratumPortStatus		3.1.1751.2.18.17.10
Current status of the primary stratum card. portFOS indicates port frequency offset.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unconfigured(1), noalarm(2), portAIS(3), portLOF(4), portLOS(5), portFOS(6)

stratumBkupPortStatus		3.1.1751.2.18.17.11
Current status of the backup stratum card. portFOS indicates port frequency offset.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unconfigured(1), noalarm(2), portAIS(3), portLOF(4), portLOS(5), portFOS(6)

activeStratum		3.1.1751.2.18.17.12
Current status of the backup stratum card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	stratumA(1), stratumB(2)

cellTestIfB		3.1.1751.2.18.18.1
Interface index used for testing cell transfer. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

cellTestVpiB		3.1.1751.2.18.18.2
VPI value for testing cell transfer to an I/O card. Valid range is a number between 0 and 4095. If the I/O card interface is not ATM, then this will always be zero.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

cellTestVcidB		3.1.1751.2.18.18.3
Virtual Check Id for testing cell transfer to an I/O card. Valid range is a number between 0 and 65535. If the I/O card interface is frame relay, this field acts as DLCI and the valid range is a number between 0 and 1023. If the I/O card interface is circuit emulation, then this will always be 0.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

cellTestServiceType		3.1.1751.2.18.18.4
Service types for testing cell transfer
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr-nrt2(2), vbr-nrt1(3), vbr-rt2(4), vbr-rt1(5), vbr-express(6), cbr4(7), cbr3(8), cbr2(9), cbr1(10)

cellTestConnType		3.1.1751.2.18.18.5
Connection types for testing cell transfer
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	simplexTx(1), simplexRx(2), duplex(3)

cellTestProtocol		3.1.1751.2.18.18.6
Protocol (interface type) on the I/O
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	atm(1), frame-relay(2), hdlc(4)

cellTestPayLoadTx		3.1.1751.2.18.18.7
PayLoad to be transmitted on I/O interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(88)

cellTestPayLoadRx		3.1.1751.2.18.18.8
Last PayLoad received on I/O interface
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(88)

cellTestAction		3.1.1751.2.18.18.9
PayLoad received on I/O interface
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	send(1), send-10(2), setupconn(3), stop(4), clearTxStats(5), clearRxStats(6)

cellTestRxPduCount		3.1.1751.2.18.18.10
Valid cells received (Input Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cellTestTxPduCount		3.1.1751.2.18.18.11
Valid cells transmitted (Output Billing Count)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cellTestMismatchPduCount		3.1.1751.2.18.18.12
Number of times Rx payload mismatched with Tx payload.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cellTestStatus		3.1.1751.2.18.18.13
Indicates whether a cellTest test is in progress or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	running(1), not-running(2)

cellTestVUNIB		3.1.1751.2.18.18.14
VUNI id for testing cell transfer to an I/O card. This field is valid only for ATM interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

sysInfoTxOneCellTotal		3.1.1751.2.18.19.1
Total amount of cells within the transmit one cell pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoTxOneCellUsed		3.1.1751.2.18.19.2
Amount of cells currently being used within the transmit one cell pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoTxOneCellHigh		3.1.1751.2.18.19.3
High-water mark of cells used within the transmit one cell pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoRxOneCellTotal		3.1.1751.2.18.19.4
Total amount of cells within the receive one cell pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoRxOneCellUsed		3.1.1751.2.18.19.5
Amount of cells currently being used within the receive one cell pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoRxOneCellHigh		3.1.1751.2.18.19.6
High-water mark of cells used within the receive one cell pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoRxMultiCellTotal		3.1.1751.2.18.19.7
Total amount of multi-cells within the receive multi-cell pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoRxMultiCellUsed		3.1.1751.2.18.19.8
Amount of multi-cells currently being used within the receive multi-cell pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoRxMultiCellHigh		3.1.1751.2.18.19.9
High-water mark of multi-cells used within the receive multi-cell pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoMsgPoolTotal		3.1.1751.2.18.19.10
Total amount of messages within the message pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoMsgPoolUsed		3.1.1751.2.18.19.11
Amount of messages currently being used within the message pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoMsgPoolHigh		3.1.1751.2.18.19.12
High-water mark of messages used within the message pool.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoDiscFreeKBytes		3.1.1751.2.18.19.13
Amount of disc free space available in KB's.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoCpuUtilization1		3.1.1751.2.18.19.14
xx.yy% - cpuUtilization1 is the xx part of it.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..99

sysInfoCpuUtilization2		3.1.1751.2.18.19.15
xx.yy% - cpuUtilization2 is the yy part of it.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..99

sysInfoSysUptime		3.1.1751.2.18.19.16
Amount of time cpu has been up in seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoBadCellRx		3.1.1751.2.18.19.17
The number of bad cells (BIP16) received so far.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoMisaligned		3.1.1751.2.18.19.18
The number of misaligned cells received so far.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoClockAErr		3.1.1751.2.18.19.19
Value is 1, TRUE, if the clock on backplane A is errored, otherwise, the value is 0, FALSE.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..1

sysInfoClockBErr		3.1.1751.2.18.19.20
Value is 1, TRUE, if the clock on backplane B is errored, otherwise, the value is 0, FALSE.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..1

sysInfoBIPAErr		3.1.1751.2.18.19.21
Value is 1, TRUE, if the cell circuit on backplane A is errored, otherwise, the value is 0, FALSE.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..1

sysInfoBIPBErr		3.1.1751.2.18.19.22
Value is 1, TRUE, if the cell circuit on backplane B is errored, otherwise, the value is 0, FALSE.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..1

sysInfoDiscTotalKBytes		3.1.1751.2.18.19.23
Amount of disc space available in KB's.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoRAMFreeKBytes		3.1.1751.2.18.19.24
Amount of RAM memory available for use in KB's.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoRAMTotalKBytes		3.1.1751.2.18.19.25
Amount of RAM memory available on cpu card in KB's.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

msgPoolViewTable		3.1.1751.2.18.19.26
Table of Msg Pools In the System, Used only for diagnostic purposes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MsgPoolViewEntry

primaryCpuHwType		3.1.1751.2.18.19.27
Indicates the hardware version type of the primary CPU. version1: 150MHz Saturn13 board supporting 8MB-64MB Memory. version2: 200MHz Saturn15 board supporting 64MB-256MB Memory.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notKnown(1), version1(2), version2(3)

secondaryCpuHwType		3.1.1751.2.18.19.28
Indicates the hardware version type of the secondary CPU. version1: 150MHz Saturn13 board supporting 8MB-64MB Memory. version2: 200MHz Saturn15 board supporting 64MB-256MB Memory.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notKnown(1), version1(2), version2(3)

msgPoolViewEntry		3.1.1751.2.18.19.26.1
Row definition of Msg Pool Table
Status: current	Access: not-accessible
OBJECT-TYPE
	MsgPoolViewEntry

msgPoolViewIndex		3.1.1751.2.18.19.26.1.1
It is the index of the MsgPool array for which the information is requested. Information about Msgs Which are not there in the free pool is returned.A msg is said to be out of the free pool by comparing the signature. The limit being the max number of msgs allowed on the system
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

msgPoolViewTskId		3.1.1751.2.18.19.26.1.2
Task Id of the Sender of the Particular Msg, This will give the integer value, has to be converted to hex for comparison
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

msgPoolViewTskName		3.1.1751.2.18.19.26.1.3
Task Name of the Sender of the Particular Msg
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(20)

msgPoolViewMsgCmd		3.1.1751.2.18.19.26.1.4
msgCmd being sent by the sending Task
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysInfoDiskCheck		3.1.1751.2.18.19.29
Indicates the checking status of the disk in CPU card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), error(2)

switchAlarmStatus		3.1.1751.2.18.19.30
Current status of the alarm on the switch. notAvailable - The alarm status could not be retreived. none - No alarm is present. minor, major, critical - An alarm of the enumerated type is present
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notAvailable(1), none(2), minor(3), major(4), critical(5)

arp1Table		3.1.1751.2.18.20.1
Table of ARP cache data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Arp1Entry

arp1Entry		3.1.1751.2.18.20.1.1
Row definition for ARP cache.
Status: current	Access: not-accessible
OBJECT-TYPE
	Arp1Entry

arp1CardSlot		3.1.1751.2.18.20.1.1.1
Slot ethernet card is in.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..16

arp1BridgeGroupNum		3.1.1751.2.18.20.1.1.2
Bridge Group the entry belongs to.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..999

arp1IpAddress		3.1.1751.2.18.20.1.1.3
Entry IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

arp1PhysicalAddr		3.1.1751.2.18.20.1.1.4
Entry physical address.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(6)

arp1EntryAge		3.1.1751.2.18.20.1.1.5
Age of cache entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

arp2Table		3.1.1751.2.18.20.2
Table of ARP cache data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Arp2Entry

arp2Entry		3.1.1751.2.18.20.2.1
Row definition for ARP cache.
Status: current	Access: not-accessible
OBJECT-TYPE
	Arp2Entry

arp2CardSlot		3.1.1751.2.18.20.2.1.1
Slot ethernet card is in.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..16

arp2BridgeGroupNum		3.1.1751.2.18.20.2.1.2
Bridge Group the entry belongs to.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..999

arp2PhysicalAddr		3.1.1751.2.18.20.2.1.3
Entry physical address.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(6)

arp2IpAddress		3.1.1751.2.18.20.2.1.4
Entry IP address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

arp2EntryAge		3.1.1751.2.18.20.2.1.5
Age of cache entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bridgeCacheTable		3.1.1751.2.18.20.3
Table of bridge cache data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BridgeCacheEntry

bridgeCacheEntry		3.1.1751.2.18.20.3.1
Row definition for bridge cache.
Status: current	Access: not-accessible
OBJECT-TYPE
	BridgeCacheEntry

bridgeCacheCardSlot		3.1.1751.2.18.20.3.1.1
Slot ethernet card is in.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..16

bridgeCacheBridgeGroupNum		3.1.1751.2.18.20.3.1.2
Bridge Group the entry belongs to.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..999

bridgeCachePhysicalAddr		3.1.1751.2.18.20.3.1.3
Entry physical address.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(6)

bridgeCacheType		3.1.1751.2.18.20.3.1.4
Type of Entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	learned(1), permanent(2), policy(3)

bridgeCacheSourcePort		3.1.1751.2.18.20.3.1.5
Port entry was obtained from.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..75

bridgeCacheEntryAge		3.1.1751.2.18.20.3.1.6
Age of cache entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

alarmStatusInputBitmap		3.1.1751.2.18.21.1
Remote status from external device. bit = 0 closed, bit = 1 open, LSB 15 bits represent 15 external inputs. MSB bit 15 is always 0.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

alarmStatusOutputBitmap		3.1.1751.2.18.21.2
Control output for alarm card. bit = 0 deactivated, bit = 1 activated, LSB 4 bits represent 4 external outputs. Bit 0 through bit 3 is output 1 through 4 Control output 4 will be activated upon power failure.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1)

alarmSeverityLevelBitmap		3.1.1751.2.18.21.3
Alarm severity level. bit = 0 noAlarm, bit = 1 Alarm present, LSB 3 bits represent severity levels. bit 0 = Minor Alarm, bit 1 = Major Alarm, bit 2 = Critical Alarm.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1)

alarmAcoStatusBitmap		3.1.1751.2.18.21.4
Audio alarm status. bit = 0 No alarm cutoff, bit = 1 Alarm cutoff, LSB 3 bits represent audio alarms. bit 0 = Local alarm cutoff, bit 1 = remote alarm cutoff, bit 2 = composite alarm cutoff status.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

oamTest		3.1.1751.2.18.22.1
OBJECT IDENTIFIER

oamTestIfB		3.1.1751.2.18.22.1.1
Interface index used for starting loopback test. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

oamTestVpiB		3.1.1751.2.18.22.1.2
VPI value under testing for oam loopback test. Valid range is a number between 0 and 4095.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

oamTestVciB		3.1.1751.2.18.22.1.3
VCI value under testing for oam loopback test. Valid range is a number between 0 and 65535.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

oamTestStatus		3.1.1751.2.18.22.1.4
Inidcates the current status of oam test.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	not-running(1), running(2), successful(3), failure(4), timedout(5), waiting-for-response(6)

oamTestAction		3.1.1751.2.18.22.1.5
Test action to be performed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sendLoopback(1), sendContinuously(2), stopTest(3), resetTxCount(4), resetRxCount(5), resetMismatchCount(6)

oamTestTxCount		3.1.1751.2.18.22.1.6
Valid cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oamTestRxCount		3.1.1751.2.18.22.1.7
Valid cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oamTestMismatchCount		3.1.1751.2.18.22.1.8
Number of times Rx correlation tag is mismatched with the Tx correlation tag.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oamTestLocationID		3.1.1751.2.18.22.1.9
Location ID of the ATM Node where the loopback is to occur.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(16)

oamTestLoopbackType		3.1.1751.2.18.22.1.10
OAM Loopback type. Determines whether to send ete or segment loopback cell, and the value of location Id field in the cell. Only for specific-location value, user specified locationId field value taken into account.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	end-to-end(1), segment-endpoint(2), next-connection-point(3), specific-location(4)

oamActDeactTable		3.1.1751.2.18.22.2
Table of oam activate and deactivate functions
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OamActDeactEntry

oamActDeactEntry		3.1.1751.2.18.22.2.1
Row definition of oam activate and deactivate
Status: current	Access: not-accessible
OBJECT-TYPE
	OamActDeactEntry

oamActDeactIfB		3.1.1751.2.18.22.2.1.1
Interface index for an OAM CC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

oamActDeactVpiB		3.1.1751.2.18.22.2.1.2
VPI value for an oam CC connection. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

oamActDeactVciB		3.1.1751.2.18.22.2.1.3
VCI value for oam CC connection. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

oamActDeactFuncType		3.1.1751.2.18.22.2.1.4
OAM Function type represents the OAM flow for activation or deactivattion for this connection. the possible function types activated in one connection are : fpm-and-br : forward performance monitoring/backward reporting fpm-only : forward performance monitoring continuity-check : continuity check pmbr-and-cc : forward performance monitoring/backward reporting and continuity check pm-and-cc : forward performance monitoring and continuity check
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	fpm-and-br(1), fpm-only(2), continuity-check(3), pmbr-and-cc(4), pm-and-cc(5)

oamActDeactDirFlow		3.1.1751.2.18.22.2.1.5
The direction in which cells will be transmitted.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	towards-far-end(1), towards-near-end(2), both-way(3)

oamActDeactFlowType		3.1.1751.2.18.22.2.1.6
Flow Type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	end-to-end(1), segment(2)

oamActDeactBlkSizeAB		3.1.1751.2.18.22.2.1.7
Block Size A-B represents the size of the block of user cells taken into consideration for performance monitoring in A-B direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	size128(1), size256(2), size512(3), size1024(4), size4096(5), size8192(6), size16384(7), size32768(8), size2048(9)

oamActDeactBlkSizeBA		3.1.1751.2.18.22.2.1.8
Block Size A-B is the size of the block of user cells taken into consideration for performance monitoring in B-A direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	size128(1), size256(2), size512(3), size1024(4), size4096(5), size8192(6), size16384(7), size32768(8), size2048(9)

oamActDeactStsSrcPointEteCC		3.1.1751.2.18.22.2.1.9
Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactStsSnkPointEteCC		3.1.1751.2.18.22.2.1.10
Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactRsltPrevReq		3.1.1751.2.18.22.2.1.11
Cause of Failure shows the reasons of failure of the last activation request on this connection form the local user.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	denied(1), timedout(2), locResrcUnavl(3), oamUnsupported(4), reqCancelled(5), funcNotImplemented(6), none(7), successful(8)

oamActDeactRowStatus		3.1.1751.2.18.22.2.1.12
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

oamActDeactStsSrcPointEtePM		3.1.1751.2.18.22.2.1.13
Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactStsSnkPointEtePM		3.1.1751.2.18.22.2.1.14
Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactStsSrcPointEtePMBR		3.1.1751.2.18.22.2.1.15
Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactStsSnkPointEtePMBR		3.1.1751.2.18.22.2.1.16
Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactBRBlockError		3.1.1751.2.18.22.2.1.17
Backware reporting Block error for PM connection. Valid range is a number between 0 and 32768.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..32768

oamActDeactBRLostInsertedCell		3.1.1751.2.18.22.2.1.18
Backware reporting lost inserted cell for PM connection. Valid range is a number between 0 and 32768.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..32768

oamActDeactBRMisInsertedCell		3.1.1751.2.18.22.2.1.19
Backware reporting misinserted cell for PM connection. Valid range is a number between 0 and 32768.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..32768

oamActDeactStsSrcPointSegPM		3.1.1751.2.18.22.2.1.20
Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactStsSnkPointSegPM		3.1.1751.2.18.22.2.1.21
Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactStsSrcPointSegPMBR		3.1.1751.2.18.22.2.1.22
Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactStsSnkPointSegPMBR		3.1.1751.2.18.22.2.1.23
Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactStsSrcPointSegCC		3.1.1751.2.18.22.2.1.24
Source point showed in the status portion displays the current status of Activation or Deactivation request for the source point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamActDeactStsSnkPointSegCC		3.1.1751.2.18.22.2.1.25
Sink point showed in the status portion displays the current status of Activation or Deactivation request for the sink point
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	activated(1), deactivated(2), waitActConfirm(3), waitDeactConfirm(4)

oamLoopbackTable		3.1.1751.2.18.22.3
Table of oam loopback functions
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OamLoopbackEntry

oamLoopbackEntry		3.1.1751.2.18.22.3.1
Row definition of oam loop back
Status: current	Access: not-accessible
OBJECT-TYPE
	OamLoopbackEntry

oamLpbkIfB		3.1.1751.2.18.22.3.1.1
Interface index used for starting loopback test. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

oamLpbkVpiB		3.1.1751.2.18.22.3.1.2
VPI value under testing for oam loopback test. Valid range is a number between 0 and 4095.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4095

oamLpbkVciB		3.1.1751.2.18.22.3.1.3
VCI value under testing for oam loopback test. Valid range is a number between 0 and 65535.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

oamLoopbackType		3.1.1751.2.18.22.3.1.4
OAM Loopback type. Determines whether to send ete or segment loopback cell, and the value of location Id field in the cell. Only for specific-location value, user specified locationId field value taken into account.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	end-to-end(1), segment-endpoint(2), next-connection-point(3), specific-location(4)

oamLpbkLocationID		3.1.1751.2.18.22.3.1.5
Location ID of the ATM Node where the loopback is to occur.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(16)

oamLpbkAction		3.1.1751.2.18.22.3.1.6
Test action to be performed. endLoopbackContinuously is not used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sendLoopbackOnce(1), sendLoopbackContinuously(2), stopTest(3), resetStats(4)

oamLpbkStatus		3.1.1751.2.18.22.3.1.7
Inidcates the current status of oam test.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inactive(1), waiting-for-response(2), successful(3), timedout(4)

oamLpbkTxCount		3.1.1751.2.18.22.3.1.8
Valid cells transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oamLpbkRxCount		3.1.1751.2.18.22.3.1.9
Valid cells received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oamLpbkMismatchCount		3.1.1751.2.18.22.3.1.10
Number of times Rx correlation tag is mismatched with the Tx correlation tag.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

oamLpbkTimeout		3.1.1751.2.18.22.3.1.11
number of time out
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprRouterConfigTable		3.1.1751.2.18.24.1
Table of Vipr Router Instance Information
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprRouterConfigEntry

viprRouterConfigEntry		3.1.1751.2.18.24.1.1
definition for VIPR Route instance attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprRouterConfigEntry

viprSlot		3.1.1751.2.18.24.1.1.1
The slot number of the Virtual Router card (SS)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

viprRouterId		3.1.1751.2.18.24.1.1.2
A unique Id for the Router Instance in a router card
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..6

viprRouterName		3.1.1751.2.18.24.1.1.3
The ASCII name of the Router Instance
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(32)

viprRouterNoOfInterfaces		3.1.1751.2.18.24.1.1.4
This variable describes the no of interfaces defined in the Router Instance
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..99

viprRouterNoOfRoutes		3.1.1751.2.18.24.1.1.5
This variable describes the no of static routes defined in the Router Instance
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1024

viprRouterAdminStatus		3.1.1751.2.18.24.1.1.6
This variable represents the various X.731 states the Router state machine can take Administartively
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

viprRouterOperStatus		3.1.1751.2.18.24.1.1.7
This variable represents the various X.731 states the Router state machine can take operationally
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), unlocked-Init(3), unlocked-Disable(4), locked-Shutting(5)

viprRouterInitTmr		3.1.1751.2.18.24.1.1.8
This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprRouterDisabWarnTmr		3.1.1751.2.18.24.1.1.9
This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprRouterShutDwnWarnTmr		3.1.1751.2.18.24.1.1.10
This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprRouterDisableWarning		3.1.1751.2.18.24.1.1.11
This variable when disabled will mask all the warning messages.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

viprRouterDisableReason		3.1.1751.2.18.24.1.1.12
This variable describes the reason why the Router in the unlocked-Disabled state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), manual(2), automatic(3)

viprRouterRowStatus		3.1.1751.2.18.24.1.1.13
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

viprIntfConfigTable		3.1.1751.2.18.24.2
Table of Vipr Interface Config Information
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprIntfConfigEntry

viprIntfConfigEntry		3.1.1751.2.18.24.2.1
definition for VIPR interface attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprIntfConfigEntry

viprIntfId		3.1.1751.2.18.24.2.1.1
A unique Id for the Interface in a router instance
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..16

viprIntfIPAddress		3.1.1751.2.18.24.2.1.2
The IP address of the entrprise network to which the interface is attached to
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

viprIntfIPNetMask		3.1.1751.2.18.24.2.1.3
The IP Subnet Mask of the entrprise network to which the interface is attached to
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

viprIntfAdminStatus		3.1.1751.2.18.24.2.1.4
This variable represents the various X.731 states the Interfce statemachine can take Administratively
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

viprIntfOperStatus		3.1.1751.2.18.24.2.1.5
This variable represents the various X.731 states the Interfce statemachine can take operationally
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), unlocked-Init(3), unlocked-Disable(4), locked-Shutting(5)

viprIntfInitTmr		3.1.1751.2.18.24.2.1.6
This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprIntfDisabWarnTmr		3.1.1751.2.18.24.2.1.7
This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprIntfShutDwnWarnTmr		3.1.1751.2.18.24.2.1.8
This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprIntfDisableWarning		3.1.1751.2.18.24.2.1.9
This variable when disabled will mask all the Disable warning messages.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

viprIntfDisableReason		3.1.1751.2.18.24.2.1.10
This variable describes the reason why the Interface in the unlocked-Disabled state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), intfDisabled(2), routDisabled(3)

viprIntfRipVersion		3.1.1751.2.18.24.2.1.11
This specifies the version of RIP that interface supports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	version-1(1), version-2(2)

viprIntfRipMode		3.1.1751.2.18.24.2.1.12
This specifies the mode in which RIP protocol runs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), active(2), passive(3)

viprIntfRowStatus		3.1.1751.2.18.24.2.1.13
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

viprIntfRipLineType		3.1.1751.2.18.24.2.1.14
This specifies the line type when the RIP version is 2. When the RIP version is 1, the RIP line type will be set to broadcast(1).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	broadcast(1), multicast(2)

viprIntfAuthPasswd		3.1.1751.2.18.24.2.1.15
The authentication password for RIP version 2
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(16)

viprSubChnlConfigTable		3.1.1751.2.18.24.3
Table of Vipr Sub Channel Config Information
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprSubChnlConfigEntry

viprSubChnlConfigEntry		3.1.1751.2.18.24.3.1
definition for VIPR sub channel attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprSubChnlConfigEntry

viprSubChnlId		3.1.1751.2.18.24.3.1.1
A unique Id for the sub channel in the interface
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..3

viprSubChnlIntfIndex		3.1.1751.2.18.24.3.1.2
The Slot Port Channel to which the IP Packet to be forwarded when the TOS specified in the incoming IP packet is matched to the TosValue, TosMask pair
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

viprSubChnlTrafficType		3.1.1751.2.18.24.3.1.3
The type of interface configured on the SSPPCCC, viprSubChnlIntfIndex
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	atm(1), fR(2), bridge(3), routing(4), inband(5)

viprSubChnlLlcEncapType		3.1.1751.2.18.24.3.1.4
The encapsulation technique used in making IP packet to ATM cell
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	vc(1), llcSnap(2)

viprSubChnlMacEncapType		3.1.1751.2.18.24.3.1.5
The encapsulation technique used in making IP packet to ATM cell
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	macHdr(1), noMacHdr(2)

viprSubChnlTosFeature		3.1.1751.2.18.24.3.1.6
Allow the user to set the TOS values or not
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

viprSubChnlTosValue		3.1.1751.2.18.24.3.1.7
The type of service specified in IP packet masked with viprSubChnlTosMask has to be equal to this value in order to have the IP packets getting forwarded in this sub channel
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

viprSubChnlTosMask		3.1.1751.2.18.24.3.1.8
The Type of Service mask
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

viprSubChnlVpiDlci		3.1.1751.2.18.24.3.1.9
The VPI/DLCI value of the connection
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

viprSubChnlVci		3.1.1751.2.18.24.3.1.10
The VCI value of the connection
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4096

viprSubChnlSarType		3.1.1751.2.18.24.3.1.11
The SAR Type supported for the connection
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	aal5(1)

viprSubChnlServiceType		3.1.1751.2.18.24.3.1.12
The Service types that are supported
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	gold(1), silver(2), bronze(3)

viprSubChnlFwdErrCorrection		3.1.1751.2.18.24.3.1.13
The Forward error correction to be used
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), eighthRate(2), quarterRate(3), halfRate(4), autoHiQ(5), auto(6), autoLoQ(7)

viprSubChnlInterworkingType		3.1.1751.2.18.24.3.1.14
The Encapsulation type used for Frame relay subchannels
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	frf8(1)

viprSubChnlFrameSize		3.1.1751.2.18.24.3.1.15
The value of this object is the size in octets of the largest frame relay information field for this PVC in the ingress direction (out of the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprSubChnlComBurstSize		3.1.1751.2.18.24.3.1.16
The value of this object is equal to the committed burst size (Bc) parameter (measured in bits) for this PVC in the ingress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprSubChnlExcessBurstSize		3.1.1751.2.18.24.3.1.17
The value of this object is equal to the excess burst size (Be) parameter (measured in bits) for this PVC in the ingress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprSubChnlCommitedInfoRate		3.1.1751.2.18.24.3.1.18
The value of this object is equal to the committed information rate (CIR) parameter (measured in bits per second) for this PVC in the ingress direction (into the frame relay UNI).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprSubChnlTimeInterval		3.1.1751.2.18.24.3.1.19
The time interval over which CIR and the burst sizes (Bc and Be) are measured in the A2B direction. The unit is milliseconds.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	64..4000

viprSubChnlAtmPeakCellRate		3.1.1751.2.18.24.3.1.20
Peak cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprSubChnlAtmSustainedCellRate		3.1.1751.2.18.24.3.1.21
Sustained cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprSubChnlAtmMaxBurstSize		3.1.1751.2.18.24.3.1.22
Maximum burst size, in cells, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprSubChnlFrPeakCellRate		3.1.1751.2.18.24.3.1.23
Peak cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlFrSustainedCellRate		3.1.1751.2.18.24.3.1.24
Sustained cell rate, in cells per second, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlFrMaxBurstSize		3.1.1751.2.18.24.3.1.25
Maximum burst size, in cells, this will reflect the frame relay parameters in atm terms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlFlowType		3.1.1751.2.18.24.3.1.26
The type of flow
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	duplex(1)

viprSubChnlAdminStatus		3.1.1751.2.18.24.3.1.27
This variable represents the various X.731 states the Sub Channel state machine can take Administartively
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

viprSubChnlOperStatus		3.1.1751.2.18.24.3.1.28
This variable represents the various X.731 states the Sub Channel state machine can take Operationally
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), unlocked-Init(3), unlocked-Disable(4), locked-Shutting(5)

viprSubChnlInitTmr		3.1.1751.2.18.24.3.1.29
This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprSubChnlDisabWarnTmr		3.1.1751.2.18.24.3.1.30
This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprSubChnlShutDwnWarnTmr		3.1.1751.2.18.24.3.1.31
This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprSubChnlDisableWarning		3.1.1751.2.18.24.3.1.32
This variable when disabled will mask all the Disable warning messages.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

viprSubChnlDisableReason		3.1.1751.2.18.24.3.1.33
This variable describes the reason why the SubChnl in the unlocked-Disabled state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), intfDisabled(2), routDisabled(3)

viprSubChnlRowStatus		3.1.1751.2.18.24.3.1.34
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

viprSubChnlImIpAddr		3.1.1751.2.18.24.3.1.35
inband management IpAddr
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

viprSubChnlImMask		3.1.1751.2.18.24.3.1.36
inband management Mask
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

viprSubChnlViB		3.1.1751.2.18.24.3.1.37
The viB value of the connection
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4096

viprSubChnlVUNIB		3.1.1751.2.18.24.3.1.38
The VUNIB value of the connection
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

viprSubChnlTrafficShaping		3.1.1751.2.18.24.3.1.39
Traffic Shaping Support in the A2B direction for outgoing ATM connections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

viprSubChnlAtmOamStatus		3.1.1751.2.18.24.3.1.40
Indicates the OAM monitoring status. The 3 possible states are: Unsupp: No monitoring enabled. End-Pt: A side is only an end point, therefore it will respond to AIS/RDI. End-Seg-Pt: Connection endPoint that is also a segment endPoint.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2), end-Seg-Pt(3)

viprRouteConfigTable		3.1.1751.2.18.24.4
Table of Vipr static route Config Information
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprRouteConfigEntry

viprRouteConfigEntry		3.1.1751.2.18.24.4.1
Definition for Vipr static route attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprRouteConfigEntry

viprRouteId		3.1.1751.2.18.24.4.1.1
The unique Id to the routing table entry
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..1024

viprRouteIPAddress		3.1.1751.2.18.24.4.1.2
The IP address of the host/network in the route entry
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

viprRouteIPNetMask		3.1.1751.2.18.24.4.1.3
The IP Subnet Mask for the route entry to identify whether the route entry is a host or network
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

viprRouteDestAddress		3.1.1751.2.18.24.4.1.4
The IP address of the host/network in the route entry
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

viprRouteGatewayAddress		3.1.1751.2.18.24.4.1.5
The IP address of the Gateway
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

viprRouteServiceType		3.1.1751.2.18.24.4.1.6
The Service types that are supported
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	gold(1), silver(2), bronze(3)

viprRouteMetric		3.1.1751.2.18.24.4.1.7
A scalar value for user-supplied static route metric values.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprRouteAdminStatus		3.1.1751.2.18.24.4.1.8
This variable represents the various X.731 states the Route state machine can take Administratively
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2)

viprRouteOperStatus		3.1.1751.2.18.24.4.1.9
This variable represents the various X.731 states the Route state machine can take Operationally
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outOfService(1), inService(2), unlocked-Init(3), unlocked-Disable(4), locked-Shutting(5)

viprRouteInitTmr		3.1.1751.2.18.24.4.1.10
This variable describes the waiting period in the locked-Init state before moving onto locked-Diable state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprRouteDisabWarnTmr		3.1.1751.2.18.24.4.1.11
This variable describes the periodicity in which the error messages are to be flashed when the system is in unlocked-Disable state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprRouteShutDwnWarnTmr		3.1.1751.2.18.24.4.1.12
This variable describes the periodicity in which the error messages are to be flashed when the system is in locked-Shutting state.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

viprRouteDisableWarning		3.1.1751.2.18.24.4.1.13
This variable when disabled will mask all the Disable warning messages.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

viprRouteDisableReason		3.1.1751.2.18.24.4.1.14
This variable describes the reason why the Route in the unlocked-Disabled state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), intfDisabled(2), routDisabled(3)

viprRouteRowStatus		3.1.1751.2.18.24.4.1.15
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

viprRouteDestMask		3.1.1751.2.18.24.4.1.16
The IP Mask of the host/network in the route entry
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

viprRoutingConfigTable		3.1.1751.2.18.24.5
Table of Vipr routes Config Information
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprRoutingConfigEntry

viprRoutingConfigEntry		3.1.1751.2.18.24.5.1
Definition for Vipr route attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprRoutingConfigEntry

viprRoutingCommand		3.1.1751.2.18.24.5.1.1
The Routing table request command Set to start to initiate the caching of first 15 entries Set to more to initiate the caching of next 15 entries Set to abort to reset the counter in I/O card Set to retrieve in order to get the entries
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	start(1), more(2), abort(3), retrieve(4)

viprRoutingIPAddress		3.1.1751.2.18.24.5.1.2
The IP address of the host/network in the route entry
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

viprRoutingIPNetMask		3.1.1751.2.18.24.5.1.3
The IP Subnet Mask for the route entry to identify whether the route entry is a host or network
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

viprRoutingDestAddress		3.1.1751.2.18.24.5.1.4
The IP address of the host/network in the route entry
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

viprRoutingGatewayAddress		3.1.1751.2.18.24.5.1.5
The IP address of the Gateway
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

viprRoutingServiceType		3.1.1751.2.18.24.5.1.6
The Service types that are supported
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	gold(1), silver(2), bronze(3)

viprRoutingType		3.1.1751.2.18.24.5.1.7
Route types supported by the RS Card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	stat(1), rip(2), ospf(3), intf(4)

viprRoutingMetric		3.1.1751.2.18.24.5.1.8
The Path cost
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprRoutingDestMask		3.1.1751.2.18.24.5.1.9
The IP address Mask of the host/network in the route entry
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

viprRoutingAge		3.1.1751.2.18.24.5.1.10
Age of the routing entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprRoutingIndex		3.1.1751.2.18.24.5.1.11
Index to the routing entry
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

viprArpConfigTable		3.1.1751.2.18.24.6
Table of Vipr Arp Table Information
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprArpConfigEntry

viprArpConfigEntry		3.1.1751.2.18.24.6.1
Definition for Vipr Arp Table attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprArpConfigEntry

viprArpCommand		3.1.1751.2.18.24.6.1.1
The ARP table request command Set to start to initiate the caching of first 15 entries Set to more to initiate the caching of next 15 entries Set to abort to reset the counter in I/O card Set to retrieve in order to get the entries
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	start(1), more(2), abort(3), retrieve(4)

viprArpIPAddress		3.1.1751.2.18.24.6.1.2
The IP address of the host/network
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

viprArpHwAddress		3.1.1751.2.18.24.6.1.3
The hardware address of the host/network
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(6)

viprArpEntryAge		3.1.1751.2.18.24.6.1.4
Age of cache entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprArpInterfaceIPAddress		3.1.1751.2.18.24.6.1.5
The Interface IP address through which it is learned
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

viprArpInterfaceIPMask		3.1.1751.2.18.24.6.1.6
The Interface IP address Mask
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

viprArpInterfaceServiceType		3.1.1751.2.18.24.6.1.7
The Service type of the interface through which the ARP table is learned
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	gold(1), silver(2), bronze(3)

viprArpIndex		3.1.1751.2.18.24.6.1.8
The Index to the Arp table
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

viprPingConfigTable		3.1.1751.2.18.24.7
Table of Vipr Ping Table Information
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprPingConfigEntry

viprPingConfigEntry		3.1.1751.2.18.24.7.1
Definition for Vipr Ping Table attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprPingConfigEntry

ipAddr		3.1.1751.2.18.24.7.1.1
The IP address of the host/network to be echoed
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

pingStatus		3.1.1751.2.18.24.7.1.2
The response value - Alive/Not Alive
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	alive(1), not-Alive(2)

viprRipConfigTable		3.1.1751.2.18.24.8
Table of Vipr Rip Update Interval for each card
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprRipConfigEntry

viprRipConfigEntry		3.1.1751.2.18.24.8.1
Definition of Rip Update attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprRipConfigEntry

viprRipUpdateInt		3.1.1751.2.18.24.8.1.1
This variable represents the Rip Update Interval used by the RIP protocol to transmit packets. The unit is in seconds. The default is 30 seconds and user can change it to 8 or 16 seconds for a route server card. The value will apply to all VPN's in a route server card. But different route server cards in different slots can have separate values for Rip Update Interval
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	lowUpdateInt(8), mediumUpdateInt(16), normalUpdateInt(30)

viprVpnStatsTable		3.1.1751.2.18.10.9
Statistics collected per vpn based
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprVpnStatsEntry

viprVpnStatsEntry		3.1.1751.2.18.10.9.1
Statistics collected per vpn based
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprVpnStatsEntry

viprVpnStatsTimer		3.1.1751.2.18.10.9.1.1
A timeout value in which the RS Module must reply to statistics requests.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutEchoRPs		3.1.1751.2.18.10.9.1.2
Echo Reply
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutDestURs		3.1.1751.2.18.10.9.1.3
Destination unreachable
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutSrcQ		3.1.1751.2.18.10.9.1.4
Source Quenches
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutRedirects		3.1.1751.2.18.10.9.1.5
Redirect message type
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutEchoRQs		3.1.1751.2.18.10.9.1.6
Echo Requests
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutTimeXs		3.1.1751.2.18.10.9.1.7
Time exceeded
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutParamps		3.1.1751.2.18.10.9.1.8
Parameter problem
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutTimeRQs		3.1.1751.2.18.10.9.1.9
Timestamp requests
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutTimeRPs		3.1.1751.2.18.10.9.1.10
Timestamp replies
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutInfoRQs		3.1.1751.2.18.10.9.1.11
Information Request
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutInfoRPs		3.1.1751.2.18.10.9.1.12
Echo Reply
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutMaskRQs		3.1.1751.2.18.10.9.1.13
Mask Request
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutMaskRPs		3.1.1751.2.18.10.9.1.14
Mask Reply
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpOutErrors		3.1.1751.2.18.10.9.1.15
unrecognized ICMP type
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInErrors		3.1.1751.2.18.10.9.1.16
error in received icmp message
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInEchoRQs		3.1.1751.2.18.10.9.1.17
received echo request
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInAddrMasks		3.1.1751.2.18.10.9.1.18
received mask request
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInAddrMaskReps		3.1.1751.2.18.10.9.1.19
received mask reply
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInEchoReps		3.1.1751.2.18.10.9.1.20
received echo replies
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInDestUnreachs		3.1.1751.2.18.10.9.1.21
received destination unreacheable message
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInSrcQuenchs		3.1.1751.2.18.10.9.1.22
received source quench
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInTimeExcds		3.1.1751.2.18.10.9.1.23
received time exceeded message
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInParamProbs		3.1.1751.2.18.10.9.1.24
received parameter problem message
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInTimeStamps		3.1.1751.2.18.10.9.1.25
received time stamp request
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprVpnStatsIcmpInTimeStampsReps		3.1.1751.2.18.10.9.1.26
received time stamp replies
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsTable		3.1.1751.2.18.11.10
The table which holds viprStatsEntry data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprStatsEntry

viprStatsEntry		3.1.1751.2.18.11.10.1
A table entry for VPN related statistics information.
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprStatsEntry

viprStatsReset		3.1.1751.2.18.11.10.1.1
A SNMP set action to reset VPN related statistics info.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

viprStatsPacketsRxHi		3.1.1751.2.18.11.10.1.2
Good packets received from the backplane
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsPacketsRxLo		3.1.1751.2.18.11.10.1.3
Good packets received from the backplane
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsPacketsTxHi		3.1.1751.2.18.11.10.1.4
packets transmitted to the backplane
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsPacketsTxLo		3.1.1751.2.18.11.10.1.5
packets transmitted to the backplane
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsMismatchCrcHi		3.1.1751.2.18.11.10.1.6
packets received has been dropped due to a mismached CRC
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsMismatchCrcLo		3.1.1751.2.18.11.10.1.7
packets received has been dropped due to a mismached CRC
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsInsufficientPcktsHi		3.1.1751.2.18.11.10.1.8
packet received length is greater than the number of cells received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsInsufficientPcktsLo		3.1.1751.2.18.11.10.1.9
packet received length is greater than the number of cells received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsExceedAal5CellsHi		3.1.1751.2.18.11.10.1.10
number of cells received is greater than the actual length of the aal5
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsExceedAal5CellsLo		3.1.1751.2.18.11.10.1.11
number of cells received is greater than the actual length of the aal5
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsPrototypeErrorsHi		3.1.1751.2.18.11.10.1.12
unrecognized encapsulation type
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsPrototypeErrorsLo		3.1.1751.2.18.11.10.1.13
unrecognized encapsulation type
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsArpProtoRxHi		3.1.1751.2.18.11.10.1.14
ARP received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsArpProtoRxLo		3.1.1751.2.18.11.10.1.15
ARP received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsIPInHdrErrorsHi		3.1.1751.2.18.11.10.1.16
IP packeted received has a bad header
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsIPInHdrErrorsLo		3.1.1751.2.18.11.10.1.17
IP packeted received has a bad header
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsIPInAddrErrorsHi		3.1.1751.2.18.11.10.1.18
IP packeted received has a bad IP Address
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprStatsIPInAddrErrorsLo		3.1.1751.2.18.11.10.1.19
IP packeted received has a bad IP Address
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsTable		3.1.1751.2.18.12.17
The table which holds viprSubChnlStatsEntry data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ViprSubChnlStatsEntry

viprSubChnlStatsEntry		3.1.1751.2.18.12.17.1
A table entry that contains IP interface sub channel statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	ViprSubChnlStatsEntry

viprSubChnlStatsInCellCountHiA		3.1.1751.2.18.12.17.1.1
cells received on rt interface from another conn
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsInCellCountLoA		3.1.1751.2.18.12.17.1.2
cells received on rt interface from another conn
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsOutCellCountHiA		3.1.1751.2.18.12.17.1.3
cells sent out of a rt interface to another dest
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsOutCellCountLoA		3.1.1751.2.18.12.17.1.4
cells sent out of a rt interface to another dest
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsInCellCountHiB		3.1.1751.2.18.12.17.1.5
cells received on atm/fr/bridge physical interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsInCellCountLoB		3.1.1751.2.18.12.17.1.6
cells received on atm/fr/bridge physical interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsOutCellCountHiB		3.1.1751.2.18.12.17.1.7
cell transmitted out of a physical atm/fr/bridge interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsOutCellCountLoB		3.1.1751.2.18.12.17.1.8
cell transmitted out of a physical atm/fr/bridge interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsTimer		3.1.1751.2.18.12.17.1.9
Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsInOdometerCellCountHiA		3.1.1751.2.18.12.17.1.10
odometer cells received on rt interface from another conn
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsInOdometerCellCountLoA		3.1.1751.2.18.12.17.1.11
odometer cells received on rt interface from another conn
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsOutOdometerCellCountHiA		3.1.1751.2.18.12.17.1.12
odometer cells sent out of a rt interface to another dest
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsOutOdometerCellCountLoA		3.1.1751.2.18.12.17.1.13
odometer cells sent out of a rt interface to another dest
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsInOdometerCellCountHiB		3.1.1751.2.18.12.17.1.14
odometer cells received on atm/fr/bridge physical interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsInOdometerCellCountLoB		3.1.1751.2.18.12.17.1.15
odometer cells received on atm/fr/bridge physical interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsOutOdometerCellCountHiB		3.1.1751.2.18.12.17.1.16
odometer cells transmitted out of a physical atm/fr/bridge interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsOutOdometerCellCountLoB		3.1.1751.2.18.12.17.1.17
odometer cells transmitted out of a physical atm/fr/bridge interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsOdometerTimer		3.1.1751.2.18.12.17.1.18
Odometer Number of seconds stats have been collecting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsOdometerReset		3.1.1751.2.18.12.17.1.19
to reset the subchannel statistics
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

viprSubChnlStatsCellsDroppedB		3.1.1751.2.18.12.17.1.20
Cells Dropped on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

viprSubChnlStatsCellsTaggedB		3.1.1751.2.18.12.17.1.21
Cells Tagged on the Incoming side of B
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

virtualIntfStatsTable		3.1.1751.2.18.11.11
Table of Virtual Interfaces Configurations
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VirtualIntfStatsEntry

virtualIntfStatsEntry		3.1.1751.2.18.11.11.1
Index is the Interface and the Virutal Interface
Status: current	Access: not-accessible
OBJECT-TYPE
	VirtualIntfStatsEntry

virtualIntfStatsIf		3.1.1751.2.18.11.11.1.1
Interface index for side A of an ATM-to-ATM PVC VCC connection. Number value is interpreted as an interface of the form, SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntfIndex

virtualIntfStatsVi		3.1.1751.2.18.11.11.1.2
VI value. Def Val is 1 because 0 cannot be configured
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..1024

virtualIntfStatsEgrCellCount		3.1.1751.2.18.11.11.1.3
Egress Cell Count on VI
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

virtualIntfStatsTimer		3.1.1751.2.18.11.11.1.4
Time, in seconds, since last reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..899

virtualIntfStatsReset		3.1.1751.2.18.11.11.1.5
stats reset field.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

cardFwVerTable		3.1.1751.2.18.23.1
Table of card firware version status
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CardFwVerEntry

cardFwVerEntry		3.1.1751.2.18.23.1.1
Row definition for card firmware version status
Status: current	Access: not-accessible
OBJECT-TYPE
	CardFwVerEntry

cardFwVerSlot		3.1.1751.2.18.23.1.1.1
card slot number
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..24

cardFwVerType		3.1.1751.2.18.23.1.1.2
Card type
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

cardFwVerCurrent		3.1.1751.2.18.23.1.1.3
Card firmware version currently loaded on firmware
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(13)

cardFwVerCurrentIsDefault		3.1.1751.2.18.23.1.1.4
curent driver is default
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cardFwVerNext		3.1.1751.2.18.23.1.1.5
Card firmware version that user wants to upgrade to. The values are limited those supported by the release.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(13)

cardFwVerNextIsDefault		3.1.1751.2.18.23.1.1.6
next driver is default
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1

cardFwDnldStatus		3.1.1751.2.18.23.1.1.7
firmware download procedure status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	failed(1), retry(2), progress(3), done(4), wrongCardType(5), wrongCardSType(6), drvUnavailable(7), drvInvHdrChksum(8), drvInvRecChksum(9), reqRepTimeout(10), cmplRepTimeout(11), mapCorrupted(12), mapUnavailable(13), mapInvChksum(14), mapNameImprop(15), cfgCorrupted(16), cfgUnavailable(17), cfgInvChksum(18), removeCardBeforeFinish(19), ioUnsupported(20)

cardFwRetries		3.1.1751.2.18.23.1.1.8
Number of times firmware download procedure failed consequently.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

fwDriverTable		3.1.1751.2.18.23.2
Table of available firmware drivers
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FwDriverEntry

fwDriverEntry		3.1.1751.2.18.23.2.1
Row definition for available firmware drivers
Status: current	Access: not-accessible
OBJECT-TYPE
	FwDriverEntry

fwSlotId		3.1.1751.2.18.23.2.1.1
driver slot id
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

fwDriverType		3.1.1751.2.18.23.2.1.2
firmware driver type - definition consistent with cardType.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

fwIsDefault		3.1.1751.2.18.23.2.1.3
firmware driver wether default or not
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

fwDriverName		3.1.1751.2.18.23.2.1.4
firmware driver file name
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(13)

fwDriverFrn		3.1.1751.2.18.23.2.1.5
Firmware Release Number of firmware driver
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

fwDriverSize		3.1.1751.2.18.23.2.1.6
file size of firmware driver
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

fwDriverChecksum		3.1.1751.2.18.23.2.1.7
checksum of firmware driver file
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

tasCmprsAnnceId		3.1.1751.2.18.25.31
Announcement ID for this announcement file to be compressed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

tasCmprsAnnceReplaceId		3.1.1751.2.18.25.32
Announcement ID of the announcement file to be replaced from the announcement table by this file.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

tasCmprsAnnceFilename		3.1.1751.2.18.25.33
File name for this announcement which is to be compressed.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(79)

tasCmprsAnnceDescription		3.1.1751.2.18.25.34
Description for this announcement which is to to be compressed.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(255)

tasCmprsAnnceCmprsType		3.1.1751.2.18.25.35
The type of compression used for storing this announcement.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	uncompressed(1), compress8k(2), compress16k(3), compress32k(4)

tasCmprsAnnceType		3.1.1751.2.18.25.36
The type of this announcement.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	voice(1), toneVoice(2), userTones(3), music(4), musicVoice(5), toneMusic(6)

tasCmprsAnnceIntfIndex		3.1.1751.2.18.25.37
Interface index in SSPPCCC format of TASM card on which this announcement is to be compressed.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

tasCmprsAction		3.1.1751.2.18.25.38
Action to be performed on this announcement.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	compress(1), delete(2), store(3)

tasTstAnnceId		3.1.1751.2.18.25.39
Announcement ID to be played for testing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

tasTstAnnceIntfIndex		3.1.1751.2.18.25.40
Interface index in SSPPCCC format of CE card on which this announcement is to be played for testing.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

tasTstAnnceLawType		3.1.1751.2.18.25.41
The type of CE card towards which this announcement is to be played. A-Law is for E1 and U-Law is for DS1
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	a-Law(1), u-Law(2)

tasTstAnnceAction		3.1.1751.2.18.25.42
Action to be performed on this announcement for testing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	playStart(1), playStop(2), playAbort(3)

tasTstLineId		3.1.1751.2.18.25.43
Test ID to be started for line testing.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

tasTstLineIntfIndex		3.1.1751.2.18.25.44
Interface index in SSPPCCC format of CE card on which this test is to be initiated.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

tasTstLineAction		3.1.1751.2.18.25.45
Test action to be performed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tstStart(1), tstStop(2), tstAbort(3)

tasMemIntfIndex		3.1.1751.2.18.25.46
Interface index in SSPPCCC format of TASM card on which the memory is to be initialised.
Status: current	Access: read-write
OBJECT-TYPE
	IntfIndex

tasMemAction		3.1.1751.2.18.25.47
Test action to be performed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	re-initialize(1)

toneAnnceIpAddress		3.1.1751.2.18.25.48
IP Address for announcement ftp server.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

toneAnnceAccountName		3.1.1751.2.18.25.49
ftp account name for access to announcement ftp server.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

toneAnnceAccountPassword		3.1.1751.2.18.25.50
ftp account password for access to announcement ftp server.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

toneAnnceSourceFile		3.1.1751.2.18.25.51
announcement file with complete path on the ftp server
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(79)

toneAnnceDestinationFile		3.1.1751.2.18.25.52
The announcementSourceFile will be renamed with MS DOS file format and placed in the /scsi/announce directory on the disk.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(12)

toneAnnceFtpStatus		3.1.1751.2.18.25.53
Current status of the ftp announcement download. Status of the software announcement. noActivity is the initial start state from boot-up. working is set while ftp'ing the announcement. The final state is one of doneSuccessfully, doneWithError, or aborted, all self-explanatory. It will stay in this state until re-boot or starting an announcement. If the state is doneWithError then announcementSwErrorStatus will be set to reflect the type of error.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noActivity(1), working(2), doneSuccessfully(3), doneWithError(4), aborted(5)

toneAnnceFtpErrorStatus		3.1.1751.2.18.25.54
The result of the finish of the ftp software announcement download. Set to a value 3-21 if announcementSwCopyStatus is doneWithError. Set to none if announcementFtpCopyStatus is doneSuccessfully. Set to userAbort if announcementSwCopyStatus is aborted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), userAbort(2), invalidIpAddress(3), invalidAccountName(4), invalidAccountPassword(5), invalidSourceFile(6), invalidDstFileNameFormat(7), dstFileNameAlreadyExist(8), tooManyAnnouncementNow(9), diskSpaceUsageExceed(10), unableToOpenFile(11), unableToMakeFtpConnection(12), unableToWriteFile(13), unableToCompleteFtp(14), unableToSpawnTask(15), unableToOpenScsiAnncDir(16), statFails(17)

toneAnnceFtpAction		3.1.1751.2.18.25.55
start ftp announcement files. When announcementFtpCopyStatus is working, the start request will be ignored. Abort will have effect only when announcementFtpCopystatus is working.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	start(1), abort(2)

atmTrunkingIWFBaseGroup		3.1.1751.2.18.28.1
OBJECT IDENTIFIER

atmTrunkingIWFIdentifier		3.1.1751.2.18.28.1.1
IWF ID for the local endpoint
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmTrunkingIWFLocalAddress		3.1.1751.2.18.28.1.2
IWF ATM address for the local endpoint
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(20)

atmTrunkingIWFMaxRemoteIWF		3.1.1751.2.18.28.1.3
Maximum remote IWF that can connect to this endpoint
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmTrunkingIWFAdminStatus		3.1.1751.2.18.28.1.4
Indicates whether the Local IWF is active or not
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2), delete(3)

atmTrunkingRemoteIWFTable		3.1.1751.2.18.28.2
Remote IWF table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmTrunkingRemoteIWFEntry

atmTrunkingRemoteIWFEntry		3.1.1751.2.18.28.2.1
Entry in atmTrunkingRemoteIWFTable
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmTrunkingRemoteIWFEntry

atmTrunkingRemoteIWFIdentifier		3.1.1751.2.18.28.2.1.1
IWF ID for the remote IWF
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

atmTrunkingRemoteIWFAddress		3.1.1751.2.18.28.2.1.2
IWF ATM address for the remote IWF
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(20)

atmTrunkingRemoteIWFTrnkMode		3.1.1751.2.18.28.2.1.3
Maximum remote IWF that can connect to this endpoint
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	switched(1), non-switched(2)

atmTrunkingRemoteIWFAdminStatus		3.1.1751.2.18.28.2.1.4
Indicates whether the Local IWF is active or not
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	up(1), down(2)

atmTrunkingRemoteIWFRowStatus		3.1.1751.2.18.28.2.1.5
Maximum remote IWF that can connect to this endpoint
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

atmTrunkingSigVccTable		3.1.1751.2.18.28.3
Table of iwf signaling vcc configuration entities
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmTrunkingSigVccEntry

atmTrunkingSigVccEntry		3.1.1751.2.18.28.3.1
Entry in atmTrunkingSigVccTable
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmTrunkingSigVccEntry

atmTrunkingSigVccRmtIWFIdentifier		3.1.1751.2.18.28.3.1.1
IWF ID for the remote IWF
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

atmTrunkingSigVccIdentifier		3.1.1751.2.18.28.3.1.2
Vcc ID assigned by the owner of this signaling Vcc
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..16383

atmTrunkingSigVccOutgoingIfIndex		3.1.1751.2.18.28.3.1.3
Intf index of the outgoing interface,readonly for SVC/SPVC
Status: current	Access: read-create
OBJECT-TYPE
	IntfIndex

atmTrunkingSigVccOutgoingVpi		3.1.1751.2.18.28.3.1.4
VPI used at the outgoing interface, readonly for SVC/SPVC
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..4095

atmTrunkingSigVccOutgoingVci		3.1.1751.2.18.28.3.1.5
VCI used at the outgoing interface, readonly for SVC/SPVC
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

atmTrunkingSigVccOwner		3.1.1751.2.18.28.3.1.6
Indicates who is the owner of the Sig VCC
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	local(1), remote(2)

atmTrunkingSigVccInactiveTimer		3.1.1751.2.18.28.3.1.7
Inactive time period on which to clear the call
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingSigVccType		3.1.1751.2.18.28.3.1.8
Indicates if the SigVcc should be setup as PVC/SPVC/SVC
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	pvc(1), spvc(2), svc(3)

atmTrunkingSigVccSignaling		3.1.1751.2.18.28.3.1.9
Indicates the signalling protocol used between the IWFs
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	pss1(1), dss1(2), dpnss(3), other(4)

atmTrunkingSigVccFwPcr01		3.1.1751.2.18.28.3.1.10
Forward PCR for the call
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingSigVccBwPcr01		3.1.1751.2.18.28.3.1.11
Backward PCR for the call
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingSigVccFwScr01		3.1.1751.2.18.28.3.1.12
Forward SCR for the call
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingSigVccBwScr01		3.1.1751.2.18.28.3.1.13
Backward SCR for the call
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingSigVccFwMbs01		3.1.1751.2.18.28.3.1.14
Forward MBS for the call
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingSigVccBwMbs01		3.1.1751.2.18.28.3.1.15
Backward MBS for the call
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingSigVccMaxAal2Vcc		3.1.1751.2.18.28.3.1.16
Maximum number of bearer VCCs controlled by this SigVcc
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingSigVccActiveAal2Vcc		3.1.1751.2.18.28.3.1.17
Number of active bearer VCCs controlled by this SigVcc
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmTrunkingSigVccOperStatus		3.1.1751.2.18.28.3.1.18
Indicates whether the Local IWF is active or not
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), outOfService(2), init(3), connecting(4), active(5), release(6)

atmTrunkingSigVccRowStatus		3.1.1751.2.18.28.3.1.19
Row status
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

atmTrunkingSigVccViB		3.1.1751.2.18.28.3.1.20
VI to associate the Egress part of A2B connection
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..1024

atmTrunkingSigVccVUNIB		3.1.1751.2.18.28.3.1.21
VUNI associated the Egress part of A2B connection
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..255

atmTrunkingSigVccRetryTimer		3.1.1751.2.18.28.3.1.22
the time(seconds) to wait before attempting to establish the ATM Trunking Signalling VCC SPVC after previous failed call attempt. 0 indicates retries will be attempted immedi ately
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingSigVccRetryLimit		3.1.1751.2.18.28.3.1.23
ATM Trunking Signalling VCC SPVC Retry Limit. 0 indicates unlimited
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingSigVccRestart		3.1.1751.2.18.28.3.1.24
The active ATM Trunking SPVC is released, if necessary, and a new setup procedure is begun if restart, otherwise, noop.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noop(2)

atmTrunkingSigVccPriority		3.1.1751.2.18.28.3.1.25
Priority of TrunkingSigVcc - priority-1 being highest priority .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	priority-1(1), priority-2(2), priority-3(3), priority-4(4)

atmTrunkingSigVccRetryCounter		3.1.1751.2.18.28.3.1.26
Indicates how many attempts to establish the connection have failed. It is reset whenever a connection is successfully established or the SigVcc SPVC is restarted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmTrunkingBrVccConfigTable		3.1.1751.2.18.28.4
Table of iwf aal2 bearer vcci configuration entities
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmTrunkingBrVccConfigEntry

atmTrunkingBrVccConfigEntry		3.1.1751.2.18.28.4.1
Row definition for iwf aal2 vcci configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmTrunkingBrVccConfigEntry

atmTrunkingBrVccRmtIWFId		3.1.1751.2.18.28.4.1.1
IWF ID for the remote IWF
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

atmTrunkingBrVccSigVccId		3.1.1751.2.18.28.4.1.2
Signalling Vcc associated with this Br Vcc
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..16383

atmTrunkingBrVccId		3.1.1751.2.18.28.4.1.3
Id of the AAL2 Bear Vcc
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..4096

atmTrunkingBrVccIf		3.1.1751.2.18.28.4.1.4
Intf index of the outgoing interface, readonly for SVC/SPVC
Status: current	Access: read-create
OBJECT-TYPE
	IntfIndex

atmTrunkingBrVccVpi		3.1.1751.2.18.28.4.1.5
VPI value of this VCC connection. Valid range is a number between 0 and 4095.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..4095

atmTrunkingBrVccVci		3.1.1751.2.18.28.4.1.6
VCI value of this VCC connection. Valid range is a number between 0 and 65535.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

atmTrunkingBrVccViB		3.1.1751.2.18.28.4.1.7
VI to associate the Egress part of A2B connection
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..1024

atmTrunkingBrVccVUNIB		3.1.1751.2.18.28.4.1.8
VUNI associated the Egress part of A2B connection
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..255

atmTrunkingBrVccServiceType		3.1.1751.2.18.28.4.1.9
service type
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	cbr-1(1), cbr-2(2), cbr-3(3), cbr-4(4), ubr(5), vbr-nrt2(6), vbr-nrt1(7), vbr-rt2(8), vbr-rt1(9), vbr-express(10)

atmTrunkingBrVccSarType		3.1.1751.2.18.28.4.1.10
sar type
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	aal1(1), aal2(2)

atmTrunkingBrVccOwner		3.1.1751.2.18.28.4.1.11
The owner of this Vcc
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	local(1), remote(2)

atmTrunkingBrVccOperStatus		3.1.1751.2.18.28.4.1.12
The Operational Status of this Bearer Vcc
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), outOfService(2), init(3), active(4), release(5)

atmTrunkingBrVccFwAtmPcr01		3.1.1751.2.18.28.4.1.13
Forward pcr (0+1)
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingBrVccBwAtmPcr01		3.1.1751.2.18.28.4.1.14
Backward pcr (0+1)
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingBrVccFwAtmScr01		3.1.1751.2.18.28.4.1.15
Forward scr (0+1)
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingBrVccBwAtmScr01		3.1.1751.2.18.28.4.1.16
Backward scr (0+1)
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingBrVccFwAtmMbs01		3.1.1751.2.18.28.4.1.17
Forward Mbs (0+1)
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingBrVccBwAtmMbs01		3.1.1751.2.18.28.4.1.18
Backward Mbs (0+1)
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingBrVccConnType		3.1.1751.2.18.28.4.1.19
connection type
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	svc(1), spvc(2), pvc(3)

atmTrunkingBrVccActiveChanCnt		3.1.1751.2.18.28.4.1.20
Number of currently active channels in this Vcc
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmTrunkingBrVccMaxAal2ChanId		3.1.1751.2.18.28.4.1.21
Max Id of channels supported within this br vcc
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	9..255

atmTrunkingBrVccCircuitModeDataSupp		3.1.1751.2.18.28.4.1.22
Circuit mode data
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmTrunkingBrVccFrameModeSupp		3.1.1751.2.18.28.4.1.23
Frame mode data
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmTrunkingBrVccFaxModSupp		3.1.1751.2.18.28.4.1.24
FAX Demodulation
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmTrunkingBrVccCASPktXportSupp		3.1.1751.2.18.28.4.1.25
Channel Associated Signaling
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmTrunkingBrVccDTMFPktXportSupp		3.1.1751.2.18.28.4.1.26
DTMF Dialed Digits
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmTrunkingBrVccMFR1PktXportSupp		3.1.1751.2.18.28.4.1.27
MF-R1 Dialed Digits
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmTrunkingBrVccMFR2PktXportSupp		3.1.1751.2.18.28.4.1.28
MF-R2 Dialed Digits
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmTrunkingBrVccPCMEncoding		3.1.1751.2.18.28.4.1.29
DTMF Dialed Digits
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(1), a-law(2), u-law(3)

atmTrunkingBrVccMaxFrameLength		3.1.1751.2.18.28.4.1.30
Maximum length of frame mode data
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..65535

atmTrunkingBrVccIdleChannSuprSupp		3.1.1751.2.18.28.4.1.31
Idle Channel Supression
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmTrunkingBrVccSilenceDetSupp		3.1.1751.2.18.28.4.1.32
Silence Detection
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmTrunkingBrVccCompressionSpec		3.1.1751.2.18.28.4.1.33
Compression Type
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(1), g726-16K(2), g726-24K(3), g726-32K(4), g726-40K(5), g729a-8K(6)

atmTrunkingBrVccAudioProfileSource		3.1.1751.2.18.28.4.1.34
Profile Source
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	itu-t(1), other(2)

atmTrunkingBrVccAudioProfileId		3.1.1751.2.18.28.4.1.35
Profile ID
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..255

atmTrunkingBrVccAvailBw		3.1.1751.2.18.28.4.1.36
Available Bandwidth left in this Vcc
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmTrunkingBrVccRowStatus		3.1.1751.2.18.28.4.1.37
Row status
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

atmTrunkingBrVccGr303Supp		3.1.1751.2.18.28.4.1.38
GR303 Support
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmTrunkingBrVccOamStatus		3.1.1751.2.18.28.4.1.39
Indicates the OAM monitoring status of side A. The 2 possible states are: Unsupp: No monitoring enabled. End-Pt: Atm side is only an end point, therefore it will respond to AIS/RDI.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unsupp(1), end-Pt(2)

atmTrunkingBrVccInactiveTimer		3.1.1751.2.18.28.4.1.40
The time(in seconds) to wait before releasing the ATM Trunking Bearer VCC SVC after all narrow band calls are dropped
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingBrVccRetryTimer		3.1.1751.2.18.28.4.1.41
the time(seconds) to wait before attempting to establish the ATM Trunking Bearer VCC SPVC after previous failed call attempt. 0 indicates retries will be attempted immediately
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingBrVccRetryLimit		3.1.1751.2.18.28.4.1.42
ATM Trunking Bearer VCC SPVC Retry Limit. 0 indicates unlimited
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmTrunkingBrVccRestart		3.1.1751.2.18.28.4.1.43
The active ATM Trunking BrVcc SPVC is released, if necessary, and a new setup procedure is begun if 'restart', otherwise, noop.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noop(2)

atmTrunkingBrVccCuTimer		3.1.1751.2.18.28.4.1.44
CuTimer represents combined use timer, is set to zero such that every ATM cell transmitted contains one, and only one, AAL2 packet, and the first octet of the AAL2 packet header follows immediately after the Start Field in the ATM cell payload. If the AAL2 packet payload is less than 44 octets, the remainder of the ATM cell payload following the end of the AAL2 packet shall be filled with zeros as padding. Each increment of CuTimer means 5ms more to wait. And cuTimer default value 4 means to wait 20ms before the ATM cell is sent out.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..8

atmTrunkingBrVccPriority		3.1.1751.2.18.28.4.1.45
Priority of TrunkingBrVcc - priority-1 being highest priority .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	priority-1(1), priority-2(2), priority-3(3), priority-4(4)

atmTrunkingBrVccRetryCounter		3.1.1751.2.18.28.4.1.46
Indicates how many attempts to establish the connection have failed. It is reset whenever a connection is successfully established or the BrVcc SPVC is restarted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmTrunkingDataChannelConfigTable		3.1.1751.2.18.28.5
Table of iwf aal2 data channel configuration entities
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmTrunkingDataChannelConfigEntry

atmTrunkingDataChannelConfigEntry		3.1.1751.2.18.28.5.1
Row definition for iwf aal2 data channel configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmTrunkingDataChannelConfigEntry

atmTrunkingDataChannelRmtIWFId		3.1.1751.2.18.28.5.1.1
IWF ID for the remote IWF
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

atmTrunkingDataChannelSigVccId		3.1.1751.2.18.28.5.1.2
Vcc ID assigned by the owner of this signaling Vcc
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..16383

atmTrunkingDataChannelBrVccId		3.1.1751.2.18.28.5.1.3
Id of the AAL2 Bear Vcc
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..4096

atmTrunkingDataChannelId		3.1.1751.2.18.28.5.1.4
The AAL2 Channel Id of this channel
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	8..255

atmTrunkingDataChanOperStatus		3.1.1751.2.18.28.5.1.5
Operational Status of this channel
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), active(2)

atmTrunkingDataChanOwner		3.1.1751.2.18.28.5.1.6
The owner of this channel
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	local(1), remote(2)

atmTrunkingDataChanNBIntf		3.1.1751.2.18.28.5.1.7
The index of narrowband interface this channel is mapped to
Status: current	Access: read-only
OBJECT-TYPE
	IntfIndex

h248TermIdTable		3.1.1751.2.18.30.1
Table of H.248 Terminations
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		H248TermIdEntry

h248TermIdEntry		3.1.1751.2.18.30.1.1
Row definition for H.248 Termination ID table
Status: current	Access: not-accessible
OBJECT-TYPE
	H248TermIdEntry

h248TermSlotId		3.1.1751.2.18.30.1.1.1
Slot # for termination
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..99

h248TermPhyPortId		3.1.1751.2.18.30.1.1.2
Physical Port # for termination
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..999

h248TermLogPortId		3.1.1751.2.18.30.1.1.3
Logical Port # for termination
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..999

h248TermChanId		3.1.1751.2.18.30.1.1.4
Chan # for termination
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..999

h248TermVpi		3.1.1751.2.18.30.1.1.5
VPI # for termination. Value 0 is reserved to indicate N/A, e.g., TDM termination. Thus, VPI = h248TermVpi - 1, for h248TermVpi > 0.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4096

h248TermVci		3.1.1751.2.18.30.1.1.6
VCI # for termination. Value 0 is reserved to indicate N/A, e.g., TDM termination. Thus, VCI = h248TermVci - 1, for h248TermVci > 0.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65536

h248TermId		3.1.1751.2.18.30.1.1.7
Termination ID is provisioned by user and used for identifying termination between MGC and MG
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(32)

h248TermAal2Cid		3.1.1751.2.18.30.1.1.8
AAL2 CID
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

h248TermActivation		3.1.1751.2.18.30.1.1.9
Activation for termination ID
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

h248TermRowStatus		3.1.1751.2.18.30.1.1.10
h248TermIdEntry row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

h248MaxNumberOfContexts		3.1.1751.2.18.31.1
The value of the property gives the maximum number of contexts that can exist at anytime. The NULL context is not included in this number.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

h248MaxTerminationsPerContext		3.1.1751.2.18.31.2
The max number of terminations allowed in a context.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

h248NormalMGExecutionTime		3.1.1751.2.18.31.3
Settable by the MGC to indicate the interval within which the MGC expects a response to any transaction from the MG (exclusive of the network delay). Value represents milliseconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

h248NormalMGCExecutionTime		3.1.1751.2.18.31.4
Settable by the MGC to indicate the interval within which the MG expects a response to any transaction from the MG (exclusive of the network delay). Value represents milliseconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

h248MGProvisionalResponseTimerValue		3.1.1751.2.18.31.5
Indicates the time within which the MGC should expect a Pending Response from the MG if a Transaction can not be completed. Initially set to h248NormalMGExecutionTime, plus network delay, but maybe lowered. Value represents milliseconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

h248MGCProvisionalResponseTimerValue		3.1.1751.2.18.31.6
Indicates the time within which the MG should expect a Pending Response from the MGC if a Transaction can not be completed. Initially set to h248NormalMGCExecutionTime, plus network delay, but maybe lowered. Value represents milliseconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

h248MGCIpAddress1		3.1.1751.2.18.31.7
The IP address of the 1st MGC.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

h248MGCIpAddress2		3.1.1751.2.18.31.8
The IP address of the 2nd MGC.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

protectionGroupTable		3.1.1751.2.18.29.1
Table of interface protection group attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ProtectionGroupEntry

protectionGroupEntry		3.1.1751.2.18.29.1.1
Defines one interface protection group
Status: current	Access: not-accessible
OBJECT-TYPE
	ProtectionGroupEntry

pgtGroupId		3.1.1751.2.18.29.1.1.1
a user selected logical number representing a protection group uniquely within a PSAX
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

pgtSwitchoverMethod		3.1.1751.2.18.29.1.1.2
switchover method to switch traffic from failed primary interface to available standby interface. In auto method, PSAX automatically switches the traffic without user intervention. In manual method, a failed primary does not switch traffic and gives control to user to do so.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), manual(2)

pgtSwitchbackMethod		3.1.1751.2.18.29.1.1.3
switchback method to switch traffic from a standby to its corresponding recovered primary interface. In auto method, PSAX automatically switches the traffic without user intervention. In manual method, standby does not switch traffic and gives control to user to do so.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), manual(2)

pgtStandbySelection		3.1.1751.2.18.29.1.1.4
Standby selection method determines the order of selection of standby when primary interface fails. The options are: sequential -- internally select next higher available standby to the last one, latest_used -- used last one freed, oldest_used -- used to longest idle one, random ­ randomly select one, explicit -- selected by user.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sequential(1), latest-used(2), oldest-used(3), random(4), explicit(5)

pgtRowStatus		3.1.1751.2.18.29.1.1.5
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

interfaceProtectionTable		3.1.1751.2.18.29.2
Table of interface protection attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		InterfaceProtectionEntry

interfaceProtectionEntry		3.1.1751.2.18.29.2.1
Defines attributes for interface protection
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceProtectionEntry

iptGroupId		3.1.1751.2.18.29.2.1.1
a user selected logical number representing a protection group uniquely within a PSAX.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

iptLogicalIntfId		3.1.1751.2.18.29.2.1.2
Logical interface number assigned by user
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

iptPhysicalIntfId		3.1.1751.2.18.29.2.1.3
physical interface in SSPPCCC format
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

iptIntfType		3.1.1751.2.18.29.2.1.4
interface primary or secondary.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	primary(1), secondary(2)

iptOperState		3.1.1751.2.18.29.2.1.5
indicates operational state of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inactive(1), active(2)

iptOperatingIntf		3.1.1751.2.18.29.2.1.6
protection operational state of the interface. Indicates which logical interface is carrying traffic originally configured for this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

iptProtCommand		3.1.1751.2.18.29.2.1.7
protection operational state of the interface. Indicates which logical interface is carrying traffic originally configured for this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), switchover(2), switchback(3)

iptSelectedStandby		3.1.1751.2.18.29.2.1.8
Standby interface logical number on which to switch traffic. Used only in case of manual switchover with explicit standby selection.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

iptRowStatus		3.1.1751.2.18.29.2.1.9
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

systemColdStartNotify		3.1.1751.2.18.8.1.1
Info : System has successfully completed initialization from a complete power down stage and is ready for operation.
Status: current	Access: read-write
NOTIFICATION-TYPE

systemWarmStartNotify		3.1.1751.2.18.8.1.2
Info : System has successfully completed initialization from a user or other system level interrupt or restart and is ready for operation.
Status: current	Access: read-write
NOTIFICATION-TYPE

ecdBootFailureNotify		3.1.1751.2.18.8.1.3
Critical : System failed in the Boot (startup) procedures. Please call Support immediately to resolve the problem.
Status: current	Access: read-write
NOTIFICATION-TYPE

referenceClockFailNotify		3.1.1751.2.18.8.1.4
Critical : The reference clock used for the operation of the bus-based backplane has failed. Please call Support immediately to resolve the problem.
Status: current	Access: read-write
NOTIFICATION-TYPE

referenceClockClearedNotify		3.1.1751.2.18.8.1.5
Info : The error in the backplane reference clock has been corrected.
Status: current	Access: read-write
NOTIFICATION-TYPE

compositeClockFailNotify		3.1.1751.2.18.8.1.6
Critical : The composite clock has failed. Please call Support immediately to resolve the problem.
Status: current	Access: read-write
NOTIFICATION-TYPE

compositeClockClearedNotify		3.1.1751.2.18.8.1.7
Info : The error in the composite clock has been corrected.
Status: current	Access: read-write
NOTIFICATION-TYPE

stratumModeChangeNotify		3.1.1751.2.18.8.1.8
Info : The current operational status of the Stratum card has changed.
Status: current	Access: read-write
NOTIFICATION-TYPE

powerSupplyStatusNotify		3.1.1751.2.18.8.1.9
Minor : Indicates the status of the power supply.
Status: current	Access: read-write
NOTIFICATION-TYPE

softwareDownloadStatusNotify		3.1.1751.2.18.8.1.10
Info : Indicates the completion status of the ftp download of a software upgrade.
Status: current	Access: read-write
NOTIFICATION-TYPE

muxReadyConfirmReceivedNotify		3.1.1751.2.18.8.1.11
Info : Indicates that the MUX (AC 120) has received a MUX_READY_CONF message in response to the MUX_READY_IND message when the AC 120 is configured as the TCP client for the AC 120 to Signalling Gateway connection.
Status: current	Access: read-write
NOTIFICATION-TYPE

muxReadyConfirmNotReceivedNotify		3.1.1751.2.18.8.1.12
Major : If AC 120 is configured as TCP client, this trap is sent if the MUX_READY_CONF message is not received after sending the MUX_READY_IND message three times. This indicates unexpected behavior on the AC 120 to Signalling Gateway link.
Status: current	Access: read-write
NOTIFICATION-TYPE

oneWayMessageWhileInTwoWayStateNotify		3.1.1751.2.18.8.1.13
Major : This trap indicates that a one way message is received from the Signalling Gateway (SG) when the AC 120 is in the two way state of the keep-alive protocol on the TCP link between the AC 120 and the SG.
Status: current	Access: read-write
NOTIFICATION-TYPE

inactivityTimerExpiredNotify		3.1.1751.2.18.8.1.14
Major : Sent by the AC 120 when the inactivity timer of the keep-alive protocoal expires, i.e. when the AC 120 does not see a message from the Signalling Gateway on the TCP link during the time period specified by the inactivity timer value setting.
Status: current	Access: read-write
NOTIFICATION-TYPE

keepAliveTimerExpiredInLlDownStateNotify		3.1.1751.2.18.8.1.15
Major : Sent by the AC 120 when the keep-alive timer expires in the LLDOWN state of the keep-alive protocol, i.e. when the AC 120 does not see a keep-alive message from the Signalling Gateway on the TCP link during the time period specified by the keep-alive timer setting.
Status: current	Access: read-write
NOTIFICATION-TYPE

keepAliveTimerExpiredInOneWayStateNotify		3.1.1751.2.18.8.1.16
Major : Sent by the AC 120 when the keep-alive timer expires in the ONE-WAY state of the keep-alive protocol, i.e. when the AC 120 does not see a keep-alive message from the Signalling Gateway on the TCP link during the time period specified by the keep-alive timer setting.
Status: current	Access: read-write
NOTIFICATION-TYPE

completeClockFailedNotify		3.1.1751.2.18.8.1.17
Critical : The stratum cards have either been removed or have failed leading to no clock being provided.
Status: current	Access: read-write
NOTIFICATION-TYPE

completeClockRecoveredNotify		3.1.1751.2.18.8.1.18
Info : A stratum card is now available to provide a clock source.
Status: current	Access: read-write
NOTIFICATION-TYPE

backplaneCircuitryFailedNotify		3.1.1751.2.18.8.1.19
Critical : There is no activity on the cell bus. Please call Support immediately to resolve the problem.
Status: current	Access: read-write
NOTIFICATION-TYPE

backplaneCircuitryRecoveredNotify		3.1.1751.2.18.8.1.20
Info : The cpu card is able to detect activity on the cell bus.
Status: current	Access: read-write
NOTIFICATION-TYPE

remoteRebootNotify		3.1.1751.2.18.8.1.21
Info : Indicates the result of the requested reboot action.
Status: current	Access: read-write
NOTIFICATION-TYPE

saveConfigurationNotify		3.1.1751.2.18.8.1.22
Info : Indicates the result of the requested save configuration.
Status: current	Access: read-write
NOTIFICATION-TYPE

versionConfigurationNotify		3.1.1751.2.18.8.1.23
Info : Indicates the completion status of the upgrade or downgrade.
Status: current	Access: read-write
NOTIFICATION-TYPE

fileTransferStatusNotify		3.1.1751.2.18.8.1.24
Info : Indicates the percent complete of the current upgrade, downgrade, or ftp download in progress.
Status: current	Access: read-write
NOTIFICATION-TYPE

ipOrMaskInvalidNotify		3.1.1751.2.18.8.1.25
Response : The indicated ip address is invalid.
Status: current	Access: read-write
NOTIFICATION-TYPE

alarmCardInputChangeNotify		3.1.1751.2.18.8.1.26
Info : Indicates that the deviceId with alarmCardReasonCode has changed its status.
Status: current	Access: read-write
NOTIFICATION-TYPE

removeConfigFilesNotify		3.1.1751.2.18.8.1.27
Info : Indicates the status of the removal of the configuration files.
Status: current	Access: read-write
NOTIFICATION-TYPE

alarmCardOutputChangeNotify		3.1.1751.2.18.8.1.28
Info : Indicates that the deviceId with alarmCardReasonCode has changed its status.
Status: current	Access: read-write
NOTIFICATION-TYPE

alarmCardAcoChangeNotify		3.1.1751.2.18.8.1.29
Info : Indicates the action taken by the indicated type of the audible alarm.
Status: current	Access: read-write
NOTIFICATION-TYPE

snmpCommunityStringsChangedToPublicNotify		3.1.1751.2.18.8.1.30
Critical : An error has been detected in the agt.pty file and the community strings have been changed to be public.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniNodeCfgNotify		3.1.1751.2.18.8.1.31
Info : Indicates that a PNNI Node has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniNodeCfgFailNotify		3.1.1751.2.18.8.1.32
Info : Indicates that a PNNI Node Creation has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniNodeModFailNotify		3.1.1751.2.18.8.1.33
Info : Indicates that a PNNI Node Modification has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniNodeDelFailNotify		3.1.1751.2.18.8.1.34
Info : Indicates that a PNNI Node Deletion has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniNodeOOSFailNotify		3.1.1751.2.18.8.1.35
Info : Indicates that the action of taking a PNNI Node Out of Service has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniNodeISFailNotify		3.1.1751.2.18.8.1.36
Info : Indicates that the action of bringing a PNNI Node into service has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniRtAddrCfgNotify		3.1.1751.2.18.8.1.37
Info : Indicates that a new PNNI Route Address has been Created.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniRtAddrCfgFailNotify		3.1.1751.2.18.8.1.38
Info : Indicates that a PNNI Route Address Configuration has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniRtAddrModFailNotify		3.1.1751.2.18.8.1.39
Info : Indicates that a PNNI Route Address Modification has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniRtAddrDelFailNotify		3.1.1751.2.18.8.1.40
Info : Indicates that a PNNI Route Address Deletion has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniRtAddrAddByIlmiNotify		3.1.1751.2.18.8.1.41
Info : Indicates that an end system Address has been dynamically added to PNNI by ILMI.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniRtAddrDelByIlmiNotify		3.1.1751.2.18.8.1.42
Info : Indicates that an end system Address has been dynamically deleted from PNNI by ILMI.
Status: current	Access: read-write
NOTIFICATION-TYPE

callContrlResAllocFailNotify		3.1.1751.2.18.8.1.43
Info: Indicates that the configuration of call control resource allocation fails.
Status: current	Access: read-write
NOTIFICATION-TYPE

differentSystemSoftwareNotify		3.1.1751.2.18.8.1.44
Critical: Indicates that the primary and backup cpu's are running different versions of software. This could cause system problems since the database files will not be transferred between cpu's so a change of cpu will result.
Status: current	Access: read-write
NOTIFICATION-TYPE

inputPortClockFailNotify		3.1.1751.2.18.8.1.45
Critical : The input port clock has failed. Please call Support immediately to resolve the problem.
Status: current	Access: read-write
NOTIFICATION-TYPE

inputPortClockClearedNotify		3.1.1751.2.18.8.1.46
Info : The error in the input port clock has been corrected.
Status: current	Access: read-write
NOTIFICATION-TYPE

oldStratumCardNotify		3.1.1751.2.18.8.1.47
Critical : This trap indicates that the primary stratum card does not support this mode of operation being applied in the stratum configuration. Card must be upgraded. A default configuration is being applied to stratum
Status: current	Access: read-write
NOTIFICATION-TYPE

stratumCardMismatchNotify		3.1.1751.2.18.8.1.48
Critical : Indicates that the secondary stratum card does not support this mode of operation being applied to the primary stratum. Card must be upgraded.
Status: current	Access: read-write
NOTIFICATION-TYPE

tasCmprsAnnceNotify		3.1.1751.2.18.8.1.49
Info : Indicates the result of the requested compress announcement operation.
Status: current	Access: read-write
NOTIFICATION-TYPE

tasTstLineNotify		3.1.1751.2.18.8.1.50
Info : Indicates the result of the requested line test initiation operation.
Status: current	Access: read-write
NOTIFICATION-TYPE

tasMemNotify		3.1.1751.2.18.8.1.51
Info : Indicates the result of the requested TASM memory initiation operation.
Status: current	Access: read-write
NOTIFICATION-TYPE

ambientTemperatureChangeNotify		3.1.1751.2.18.8.1.52
Info : Indicates the ambient temperature has changed by 5 degrees centigrade since the last trap message.
Status: current	Access: read-write
NOTIFICATION-TYPE

systemInsuffMemNotify		3.1.1751.2.18.8.1.53
Info : no enough memory for one or more features to be turned on.
Status: current	Access: read-write
NOTIFICATION-TYPE

toneAnnceFtpStatusNotify		3.1.1751.2.18.8.1.54
Info : Indicates the completion status of the ftp download of a tone annoucement file.
Status: current	Access: read-write
NOTIFICATION-TYPE

tasmControlBlockResAllocFailNotify		3.1.1751.2.18.8.1.55
Info: Indicates that the configuration of tasm control block resource allocation fails. Data send with the trap: tasmControlBlockAllocFailReasonCode Possible values are: res-alloc-success(1), res-alloc-Fail-announce-control-blocks-mem-unavail(2), res-alloc-Fail-digit-control-blocks-mem-unavail(3), res-alloc-Fail-line-test-control-blocks-mem-unavail(4)
Status: current	Access: read-write
NOTIFICATION-TYPE

tasmCacheMemAllocFailNotify		3.1.1751.2.18.8.1.56
Info: Indicates that the configuration of tasm memory cache for announcement caching allocation fails. Data send with the trap:tasmCacheMemAllocFailReasonCode Possible values are: res-alloc-success(1), res-alloc-Fail-announce-cache-mem-unavail(2)
Status: current	Access: read-write
NOTIFICATION-TYPE

remoteDbOperationStatusNotify		3.1.1751.2.18.8.1.57
Info : Indicates the completion status of remote database operation.
Status: current	Access: read-write
NOTIFICATION-TYPE

sapphireInterfaceAddressAssignFailNotify		3.1.1751.2.18.8.1.58
Info: Indicates that the assignment of the Sapphire interface address on which TCP connect requests are sent to SoftSwitch when PSAX is configured as Client has failed. Data send with the trap: sapphireIntfAddressFailReasonCode Possible values are: address-ok(1), Address assignment succeeded fail-Ilegal-IP-address(2), Illegal IP address assigned address not matching fail-not-match-InBandManagement-Switch-CPU-IP-Address(3) In-Band Management IP or Switch IP or CPU IP address fail-Switch-or-CPU-IP-Address-unconfigured(4) Switch IP or CPU IP address unconfigured fail-InBandManagement-IP-Address-unconfigured(5) InBandManagement IP address unconfigured.
Status: current	Access: read-write
NOTIFICATION-TYPE

switchAlarmStatusChangeNotify		3.1.1751.2.18.8.1.59
Critical : Trap to notify a change in the status of the alarm on the switch.
Status: current	Access: read-write
NOTIFICATION-TYPE

chassisOverTempAlarmNotify		3.1.1751.2.18.8.1.60
Critical : Trap sent when the temperature of the chassis goes above or below a preset temperature threshold.
Status: current	Access: read-write
NOTIFICATION-TYPE

cardInsertionNotify		3.1.1751.2.18.8.2.1
Info : The indicated slot has had a card inserted into it.
Status: current	Access: read-write
NOTIFICATION-TYPE

cardRemovedOrFailedNotify		3.1.1751.2.18.8.2.2
Major : The indicated slot has changed state.
Status: current	Access: read-write
NOTIFICATION-TYPE

lineStatusChangedNotify		3.1.1751.2.18.8.2.3
Major : The indicated port has had a change in the line status.
Status: current	Access: read-write
NOTIFICATION-TYPE

firmwareDownloadSucceededNotify		3.1.1751.2.18.8.2.4
Info : The indicated slot has successfully completed a firmware download.
Status: current	Access: read-write
NOTIFICATION-TYPE

firmwareDownloadFailedNotify		3.1.1751.2.18.8.2.5
Minor : The indicated slot had the indicated failure during a firmware download.
Status: current	Access: read-write
NOTIFICATION-TYPE

moduleRebootNotify		3.1.1751.2.18.8.2.6
Major : This trap indicates that a cardType in cardSlot becomes busy and the CPU reboots it. This is different from when an I/O card is actually removed.
Status: current	Access: read-write
NOTIFICATION-TYPE

oc3APSStateChangeNotify		3.1.1751.2.18.8.2.7
Notification of a change in the APS state machine.
Status: current	Access: read-write
NOTIFICATION-TYPE

oc3APSSwitchoverNotify		3.1.1751.2.18.8.2.8
Notification of a switchover in an APS pair.
Status: current	Access: read-write
NOTIFICATION-TYPE

portModifyFailNotify		3.1.1751.2.18.8.2.9
Info : Notification that an attempt to modify an port parameters has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

stratumActivitySwitchOverNotify		3.1.1751.2.18.8.2.10
Info : The secondary stratum card has become the primary primary card.
Status: current	Access: read-write
NOTIFICATION-TYPE

imaGroupStatusChangeNotify		3.1.1751.2.18.8.2.11
The indicated SSPPCCC has a change in the states of the IMA Group Channel
Status: current	Access: read-write
NOTIFICATION-TYPE

interfaceCreatedNotify		3.1.1751.2.18.8.3.1
Info : Notification that an interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

interfaceDeletedNotify		3.1.1751.2.18.8.3.2
Info : Notification that an interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

interfaceModifiedNotify		3.1.1751.2.18.8.3.3
Info : Notification that an interface has been modified.
Status: current	Access: read-write
NOTIFICATION-TYPE

interfaceModifyFailNotify		3.1.1751.2.18.8.3.4
Info : Notification that an attempt to modify an interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

interfaceOutOfServiceNotify		3.1.1751.2.18.8.3.5
Major : Notification that an interface is now out of service.
Status: current	Access: read-write
NOTIFICATION-TYPE

interfaceInServiceNotify		3.1.1751.2.18.8.3.6
Info : Notification that an interface is now in service.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeDomainFullNotify		3.1.1751.2.18.8.3.7
Info : The 15 ports available for the bridge domain are being used, leaving no space for an additional port.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeDomainExceededForSlotNotify		3.1.1751.2.18.8.3.8
Info : The bridge domain number has been exceeded for the slot.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeDomainNumberInUseNotify		3.1.1751.2.18.8.3.9
Info : Notification that a bridge domain number is currently in use.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeDomainInServiceNotify		3.1.1751.2.18.8.3.10
Info : Notification that a bridge domain is now in service.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeDomainNumberInvalidNotify		3.1.1751.2.18.8.3.11
Info : Indicates that this interface contains an invalid bridge domain number. In order to create a domain, associate a port with a domain, or bring an interface in service, a valid domain number must be provided.
Status: current	Access: read-write
NOTIFICATION-TYPE

signalingModifyFailNotify		3.1.1751.2.18.8.3.12
Info : This trap indicates that signaling has already been configured for this port and to change, you must bring all interfaces out of service -- including the channel specified in interfaceIndex.
Status: current	Access: read-write
NOTIFICATION-TYPE

lmiIntfStatusNotify		3.1.1751.2.18.8.3.13
Info : This trap indicates the status of an interface from the LMI perspective.
Status: current	Access: read-write
NOTIFICATION-TYPE

isdnLapdDownNotify		3.1.1751.2.18.8.3.14
Info : This trap indicates that LAPD on the ISDN interface has gone down.
Status: current	Access: read-write
NOTIFICATION-TYPE

isdnLapdUpNotify		3.1.1751.2.18.8.3.15
Info : This trap indicates that LAPD is functional on the specified ISDN interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeDomainTimingRelationshipNotify		3.1.1751.2.18.8.3.16
Info : Trap sent when one of the following relationships is violated: (1) 2 * (BridgeForwardDelay - 1.0 sec) >= BridgeMaxAge (2) BridgeMaxAge >= 2 * (BridgeHelloTime + 1.0 sec).
Status: current	Access: read-write
NOTIFICATION-TYPE

ts16UsageModifyFailNotify		3.1.1751.2.18.8.3.17
Info : Indicates that either TS16 has been in use for data while trying to change e1 TS16 from CCS to CAS, or signaling is on for at least one of the channels while trying to change e1 TS16 from CAS to CCS.
Status: current	Access: read-write
NOTIFICATION-TYPE

ceServiceTypeModifyFailNotify		3.1.1751.2.18.8.3.18
Info : Indicates that configuring unstructured CE failed. Possible reasons are: (1) the port has been channelized; (2) the port has CAS turned on.
Status: current	Access: read-write
NOTIFICATION-TYPE

channelizationModifyFailNotify		3.1.1751.2.18.8.3.19
Info : Indicates that channelizing/unchannelizing failed. Possible reasons are: (1) the port has been configured for unstructured CE; (2) the port has CAS turned on.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmSpvcConfiguredNotify		3.1.1751.2.18.8.3.20
Info : Notification that an endpoint has been configured as CES SPVC endpoint. Return value - interfaceIndex
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmSpvcConfigFailNotify		3.1.1751.2.18.8.3.21
Info : Notification that an attempt to configure an endpoint as CE SPVC endpoint has failed. Return values - interfaceIndex - spvcConfigFailureCode: An identified reason for failure while configuring/modifying SPVC parameters.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmSpvcDeletedNotify		3.1.1751.2.18.8.3.22
Info : Notification that CE SPVC configuration has been deleted. Return value - interfaceIndex
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmSpvcModifiedNotify		3.1.1751.2.18.8.3.23
Info : Notification that a SPVC endpoint has been modified - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmSpvcModifyFailNotify		3.1.1751.2.18.8.3.24
Info : Notification that an attempt to modify a CE SPVC endpoint has failed - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrSpvcConfiguredNotify		3.1.1751.2.18.8.3.25
Info : Notification that an endpoint has been configured as TE SPVC endpoint. Return value - interfaceIndex
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrSpvcConfigFailNotify		3.1.1751.2.18.8.3.26
Info : Notification that an attempt to configure an endpoint as TE SPVC endpoint has failed. Return values - interfaceIndex - spvcConfigFailureCode: An identified reason for failure while configuring/modifying SPVC parameters.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrSpvcDeletedNotify		3.1.1751.2.18.8.3.27
Info : Notification that TE SPVC configuration has been deleted. Return value - interfaceIndex
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrSpvcModifiedNotify		3.1.1751.2.18.8.3.28
Info : Notification that a SPVC endpoint has been modified - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrSpvcModifyFailNotify		3.1.1751.2.18.8.3.29
Info : Notification that an attempt to modify a TE SPVC endpoint has failed - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmSpvcConfiguredNotify		3.1.1751.2.18.8.3.30
Info : Notification that an endpoint has been configured as ATM SPVC endpoint. Return value - interfaceIndex - A-side vpi/vci value
Status: current	Access: read-write
NOTIFICATION-TYPE

atmSpvcConfigFailNotify		3.1.1751.2.18.8.3.31
Info : Notification that an attempt to configure an endpoint as ATM SPVC endpoint has failed. Return value - interfaceIndex - A-side vpi/vci value - spvcConfigFailureCode: An identified reason for failure while configuring/modifying SPVC parameters.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmSpvcDeletedNotify		3.1.1751.2.18.8.3.32
Info : Notification that ATM SPVC configuration has been deleted. Return value - interfaceIndex - A-side vpi/vci value
Status: current	Access: read-write
NOTIFICATION-TYPE

atmSpvcModifiedNotify		3.1.1751.2.18.8.3.33
Info : Notification that a SPVC endpoint has been modified - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmSpvcModifyFailNotify		3.1.1751.2.18.8.3.34
Info : Notification that an attempt to modify a TE SPVC endpoint has failed - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

cRC4ModifyFailNotify		3.1.1751.2.18.8.3.35
Info: Notification that modification of the CRC4 field of an E1 port failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

imaGrpChannelFailNotify		3.1.1751.2.18.8.3.36
Info : The imaGrpChannelFailNotify trap indicates a failure in the IMA group. The imaGrpChannelStatus field indicates the reason for the failure.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmImaIntfFailNotify		3.1.1751.2.18.8.3.37
Info : The atmImaIntfFailNotify trap indicates a failure in the physical IMA interface. The atmImaIntfStatus field indicates the reason for the failure.
Status: current	Access: read-write
NOTIFICATION-TYPE

imaGrpChannelClearedNotify		3.1.1751.2.18.8.3.38
Info : The imaGrpChannelClearedNotify trap indicates a failure has been cleared in an IMA group. The imaGrpChannelStatus field indicates the failure that has been cleared.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmImaIntfClearedNotify		3.1.1751.2.18.8.3.39
Info : The atmImaIntfClearedNotify trap indicates a failure has been cleared in an IMA interface. The atmImaIntfStatus field indicates the failure that has been cleared.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniProtLnkUpAndAdv		3.1.1751.2.18.8.3.40
Info : Indicates that the Protocol Status of the PNNI Link is Up and Advertising.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniProtLinkUpAndNotAdv		3.1.1751.2.18.8.3.41
Info : Indicates that the Protocol Status of the PNNI Link is Up but not Advertising.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniProtLnkStatDown		3.1.1751.2.18.8.3.42
Info : Indicates that the Protocol Status of the PNNI Link is Down.
Status: current	Access: read-write
NOTIFICATION-TYPE

pnniIntfCfgFailNotify		3.1.1751.2.18.8.3.43
Info : Indicates that a PNNI Interface has failed to be Created.
Status: current	Access: read-write
NOTIFICATION-TYPE

viprPingTrap		3.1.1751.2.18.8.3.44
Info : The Vipr Task is notifying Network Management of the disposition of a previous Ping Request.
Status: current	Access: read-write
NOTIFICATION-TYPE

viprArpTrap		3.1.1751.2.18.8.3.45
Info : The Vipr Task is notifying Network Management of the disposition of a previous Arp Table Request.
Status: current	Access: read-write
NOTIFICATION-TYPE

viprRoutingTrap		3.1.1751.2.18.8.3.46
Info : The Vipr Task is notifying Network Management of the disposition of a previous Routing Table Request.
Status: current	Access: read-write
NOTIFICATION-TYPE

viprVpnTrap		3.1.1751.2.18.8.3.47
Info : Indicates success/fail of VPN level operations.
Status: current	Access: read-write
NOTIFICATION-TYPE

viprIpIntfTrap		3.1.1751.2.18.8.3.48
Info : Indicates success/fail of IP Network Interface level operations.
Status: current	Access: read-write
NOTIFICATION-TYPE

viprSubChanTrap		3.1.1751.2.18.8.3.49
Info : Indicates success/fail of Sub Channel level operations.
Status: current	Access: read-write
NOTIFICATION-TYPE

viprRtSrvTrap		3.1.1751.2.18.8.3.50
Info : Indicates success/fail of Vipr (Route Server) operations.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmSvcIntfLayer2Up		3.1.1751.2.18.8.3.51
Info : Indicates that an ATM Svc Interface Assured Data Link is Up.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmSvcIntfLayer2Down		3.1.1751.2.18.8.3.52
Info : Indicates that an ATM Svc Interface Assured Data Link is Down.
Status: current	Access: read-write
NOTIFICATION-TYPE

apsConfigurationModifyFailNotify		3.1.1751.2.18.8.3.53
Info: Notification that an attempt to modify an APS configuration has failed
Status: current	Access: read-write
NOTIFICATION-TYPE

viprStatRtTrap		3.1.1751.2.18.8.3.54
Info : Indicates success/fail of Static Route operations.
Status: current	Access: read-write
NOTIFICATION-TYPE

interfaceCreateFailNotify		3.1.1751.2.18.8.3.55
Info : Notification that an attempt to create an interface has failed. interfaceFailureReasonCode gives details.
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualIntfCreatedNotify		3.1.1751.2.18.8.3.56
Response to creation of VI
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualIntfModifiedNotify		3.1.1751.2.18.8.3.57
Response to modification of VI
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualIntfDeleteNotify		3.1.1751.2.18.8.3.58
Response to deletion of VI
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualIntfModifyFailNotify		3.1.1751.2.18.8.3.59
Response to Modify Fail of VI, Overload pvcFailureReasonCode
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmSpvcConfiguredNotify		3.1.1751.2.18.8.3.60
Info : Notification that an endpoint has been configured as FR SPVC endpoint. Return values - interfaceIndex - dlci value
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmSpvcConfigFailNotify		3.1.1751.2.18.8.3.61
Info : Notification that an attempt to configure an endpoint as FR SPVC endpoint has failed. Return values - interfaceIndex - dlci value - spvcConfigFailureCode: An identified reason for failure while configuring/modifying SPVC parameters.
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmSpvcDeletedNotify		3.1.1751.2.18.8.3.62
Info : Notification that FR SPVC configuration has been deleted. Return values - interfaceIndex - dlci value
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmSpvcModifiedNotify		3.1.1751.2.18.8.3.63
Info : Notification that a SPVC endpoint has been modified - this trap has been obsoleted 07/01/2001. Return values - interfaceIndex - dlci value
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmSpvcModifyFailNotify		3.1.1751.2.18.8.3.64
Info : Notification that an attempt to modify a FR SPVC endpoint has failed - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvcConfiguredNotify		3.1.1751.2.18.8.3.65
Info : Notification that an endpoint has been configured as ATM SPVC endpoint. Return values - interfaceIndex - A-side vpi/vci values - remote NSAP address
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvcConfigFailNotify		3.1.1751.2.18.8.3.66
Info : Notification that an attempt to configure an endpoint as ATM SPVC endpoint has failed. Return values - interfaceIndex - A-side vpi/vci values - remote NSAP address - spvcConfigFailureCode: An identified reason for failure while configuring/modifying SPVC parameters
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvcDeletedNotify		3.1.1751.2.18.8.3.67
Info : Notification that ATM SPVC configuration has been deleted. Return values - interfaceIndex - A-side vpi/vci values - remote NSAP address
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvcModifiedNotify		3.1.1751.2.18.8.3.68
Info : Notification that a SPVC endpoint has been modified - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvcModifyFailNotify		3.1.1751.2.18.8.3.69
Info : Notification that an attempt to modify a TE SPVC endpoint has failed - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirAtmSpvcConfiguredNotify		3.1.1751.2.18.8.3.70
Info : Notification that an endpoint has been configured as CE SPVC endpoint. Return values - interfaceIndex - remote NSAP address
Status: current	Access: read-write
NOTIFICATION-TYPE

cirAtmSpvcConfigFailNotify		3.1.1751.2.18.8.3.71
Info : Notification that an attempt to configure an endpoint as CE SPVC endpoint has failed. Return values - interfaceIndex - remote NSAP address - spvcConfigFailureCode: An identified reason for failure while configuring/modifying SPVC parameters
Status: current	Access: read-write
NOTIFICATION-TYPE

cirAtmSpvcDeletedNotify		3.1.1751.2.18.8.3.72
Info : Notification that CE SPVC configuration has been deleted. Return values - interfaceIndex - remote NSAP address
Status: current	Access: read-write
NOTIFICATION-TYPE

cirAtmSpvcModifiedNotify		3.1.1751.2.18.8.3.73
Info : Notification that a SPVC endpoint has been modified - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirAtmSpvcModifyFailNotify		3.1.1751.2.18.8.3.74
Info : Notification that an attempt to modify a CE SPVC endpoint has failed - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmSpvcConfiguredNotify		3.1.1751.2.18.8.3.75
Info : Notification that an endpoint has been configured as TE SPVC endpoint. Return values - interfaceIndex - remote NSAP address
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmSpvcConfigFailNotify		3.1.1751.2.18.8.3.76
Info : Notification that an attempt to configure an endpoint as TE SPVC endpoint has failed. Return values - interfaceIndex - remote NSAP address - spvcConfigFailureCode: An identified reason for failure while configuring/modifying SPVC parameters
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmSpvcDeletedNotify		3.1.1751.2.18.8.3.77
Info : Notification that TE SPVC configuration has been deleted. Return values - interfaceIndex - remote NSAP address
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmSpvcModifiedNotify		3.1.1751.2.18.8.3.78
Info : Notification that a SPVC endpoint has been modified - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmSpvcModifyFailNotify		3.1.1751.2.18.8.3.79
Info : Notification that an attempt to modify a TE SPVC endpoint has failed - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualUNIIntfCreatedNotify		3.1.1751.2.18.8.3.80
Response to creation of Virtual UNI
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualUNIIntfCreateFailNotify		3.1.1751.2.18.8.3.81
Info : Notification that an attempt to create an interface has failed. interfaceFailureReasonCode gives details.
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualUNIIntfModifiedNotify		3.1.1751.2.18.8.3.82
Notification of a failure to modify a Virtual UNI interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualUNIIntfDeleteNotify		3.1.1751.2.18.8.3.83
Response to deletion of Virtual UNI
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualUNIIntfModifyFailNotify		3.1.1751.2.18.8.3.84
Response to Modify Fail of Virtual UNI, Overload interfaceFailureReasonCode
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualUNIIntfOutOfServiceNotify		3.1.1751.2.18.8.3.85
Notification of virtualUNI Out Of Service
Status: current	Access: read-write
NOTIFICATION-TYPE

virtualUNIIntfInServiceNotify		3.1.1751.2.18.8.3.86
Notification of virtualUNI in Service
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303IgCreatedNotify		3.1.1751.2.18.8.3.87
Response to creation of GR303IG
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303IgCreateFailNotify		3.1.1751.2.18.8.3.88
Info : Notification that an attempt to create a gr303 interface group has failed. interfaceFailureReasonCode gives details.
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303IgModifiedNotify		3.1.1751.2.18.8.3.89
Response to modification of GR303IG
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303IgDeleteNotify		3.1.1751.2.18.8.3.90
Response to deletion of GR303IG
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303IgModifyFailNotify		3.1.1751.2.18.8.3.91
Response to Modify Fail of GR303IG, Overload interfaceFailureReasonCode
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303IgOutOfServiceNotify		3.1.1751.2.18.8.3.92
Notification of GR303IG Out Of Service
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303IgInServiceNotify		3.1.1751.2.18.8.3.93
Notification of GR303IG in Service
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303IgIntfAddedNotify		3.1.1751.2.18.8.3.94
Response to addition of DS1 interface into GR303IG
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303IgIntfAddFailNotify		3.1.1751.2.18.8.3.95
Info : Notification that an attempt to add an interface has failed. interfaceFailureReasonCode gives details.
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303IgIntfDeleteNotify		3.1.1751.2.18.8.3.96
Response to deletion of DS1 interface from GR303IG
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303TMCChanDownNotify		3.1.1751.2.18.8.3.97
Info : This trap indicates that TMC (LAPD) on the GR303 interface has gone down.
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303EOCChanDownNotify		3.1.1751.2.18.8.3.98
Info : This trap indicates that EOC (LAPD) on the GR303 interface has gone down.
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303TMCChanUpNotify		3.1.1751.2.18.8.3.99
Info : This trap indicates that TMC(LAPD) is functional on the specified GR303 interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303EOCChanUpNotify		3.1.1751.2.18.8.3.100
Info : This trap indicates that EOC(LAPD) is functional on the specified GR303 interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303PPSStateChangeNotify		3.1.1751.2.18.8.3.101
This indicates a change in the states of primary and secondary TMC/EOC (lapd)
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303PPSSwitchoverNotify		3.1.1751.2.18.8.3.102
This notification is the result of PPS switching command which will indicate the reason code, initiator and states
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303PPSCommandFailNotify		3.1.1751.2.18.8.3.103
This is the notification of failure of PPS switching command
Status: current	Access: read-write
NOTIFICATION-TYPE

interfaceBandwidthChangeNotify		3.1.1751.2.18.8.3.104
Info : Notification that a interface has undergone reduction in bandwidth. Critical depending on Failure Reason Code.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvpConfiguredNotify		3.1.1751.2.18.8.3.105
Info : Notification that an ATM SPVP has been configured at the ATM SPVC endpoint. Return values - interfaceIndex - A-side vpi value - remote NSAP Address
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvpConfigFailNotify		3.1.1751.2.18.8.3.106
Info : Notification that an attempt to configure an ATM SPVP at the ATM SPVC endpoint has failed. Return values - interfaceIndex - A-side vpi value - remote NSAP Address - spvcConfigFailureCode: An identified reason for failure while configuring/modifying SPVC parameters.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvpDeletedNotify		3.1.1751.2.18.8.3.107
Info : Notification that an ATM SPVP configuration has been deleted. Return values - interfaceIndex - A-side vpi value - remote NSAP Address
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvpModifiedNotify		3.1.1751.2.18.8.3.108
Info : Notification that an ATM SPVP configuration has been modified - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvpModifyFailNotify		3.1.1751.2.18.8.3.109
Info : Notification that an attempt to modify a ATM SPVP configuration has failed - this trap has been obsoleted 07/01/2001.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingLocalIWFConfiguredNotify		3.1.1751.2.18.8.3.110
Info: Local IWF Configured return value: atmTrunkingIWFIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingLocalIWFConfigFailNotify		3.1.1751.2.18.8.3.111
Info: Local IWF Configured return value: atmTrunkingIWFIdentifier atmTrunkingConfigFailureCode
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingLocalIWFModifiedNotify		3.1.1751.2.18.8.3.112
Info: configuration of Local IWF modified return value: atmTrunkingIWFIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingLocalIWFModifyFailNotify		3.1.1751.2.18.8.3.113
Info: Modification of Local IWF has failed return value: atmTrunkingIWFIdentifier atmTrunkingConfigFailureCode
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingLocalIWFDeletedNotify		3.1.1751.2.18.8.3.114
Info: configuration of Local IWF deleted return value: atmTrunkingIWFIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingLocalIWFDeleteFailNotify		3.1.1751.2.18.8.3.115
Info: configuration of Local IWF can not be deleted return value: atmTrunkingIWFIdentifier atmTrunkingConfigFailureCode
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingRemoteIWFConfiguredNotify		3.1.1751.2.18.8.3.116
Info : Notification that an ATM TRUNKING Remote IWF has been configured with return values - atmTrunkingRmtIWFIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingRemoteIWFConfigFailNotify		3.1.1751.2.18.8.3.117
Info : Notification that an ATM TRUNKING Remote IWF configuration has failed with return value : - atmTrunkingRmtIWFIdentifier - atmTrunkingConfigFailureCode
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingRemoteIWFDeletedNotify		3.1.1751.2.18.8.3.118
Info : Notification that an ATM TRUNKING Remote IWF has been deleted with return values - atmTrunkingRmtIWFIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingRemoteIWFModifiedNotify		3.1.1751.2.18.8.3.119
Info : Notification that an ATM TRUNKING Remote IWF has been modified with return values - atmTrunkingRmtIWFIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingRemoteIWFModifyFailNotify		3.1.1751.2.18.8.3.120
Info : Notification that an ATM TRUNKING Remote IWF has been configured with return values - atmTrunkingRmtIWFIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingSigVccConfiguredNotify		3.1.1751.2.18.8.3.121
Info : Notification that an ATM TRUNKING Signalling VCC has been configured between Local IWF and with return values - atmTrunkingSigVccRmtIWFIdentifier - atmTrunkingSigVccIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingSigVccConfigFailNotify		3.1.1751.2.18.8.3.122
Info : Notification that an ATM TRUNKING Signalling VCC configuration has failed with return value: - atmTrunkingSigVccRmtIWFIdentifier - atmTrunkingSigVccIdentifier - atmTrunkingConfigFailureCode
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingSigVccDeletedNotify		3.1.1751.2.18.8.3.123
Info : Notification that an ATM TRUNKING Signalling VCC has been deleted with return values - atmTrunkingSigVccRmtIWFIdentifier - atmTrunkingSigVccIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingBrVccConfiguredNotify		3.1.1751.2.18.8.3.124
Info : Notification that an ATM TRUNKING Bearer VCC has been configured between Local IWF and with return values - atmTrunkingBrVccRmtIWFIdentifier - atmTrunkingBrVccIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingBrVccConfigFailNotify		3.1.1751.2.18.8.3.125
Info : Notification that an ATM TRUNKING Bearer VCC configuration has failed with return value: - atmTrunkingBrVccRmtIWFIdentifier - atmTrunkingBrVccIdentifier - atmTrunkingConfigFailureCode
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingBrVccDeletedNotify		3.1.1751.2.18.8.3.126
Info : Notification that an ATM TRUNKING Bearer VCC has been deleted with return values - atmTrunkingBrVccRmtIWFIdentifier - atmTrunkingBrVccIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmPvcVccReqFailNotify		3.1.1751.2.18.8.4.1
Response : The PVC VCC connection request between two atm interfaces failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmPvcVpcReqFailNotify		3.1.1751.2.18.8.4.2
Response : The PVC VPC connection request between two atm interfaces failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

ipAtmAppPvcVccReqFailNotify		3.1.1751.2.18.8.4.3
Response : The PVC VCC connection request between in-band management and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmAtmPvcVccReqFailNotify		3.1.1751.2.18.8.4.4
Response : The PVC VCC connection request between a circuit emulation interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmPvcVccReqFailNotify		3.1.1751.2.18.8.4.5
Response : The PVC VCC connection request between a variable-bit rate interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmPvcVccReqFailNotify		3.1.1751.2.18.8.4.6
Response : The PVC VCC connection request between a frame-relay interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

frFrPvcReqFailNotify		3.1.1751.2.18.8.4.7
Response : The PVC connection request between two frame-relay interfaces has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmCirEmPvcReqFailNotify		3.1.1751.2.18.8.4.8
Response : The PVC connection request between two circuit emulation interfaces has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrVbrPvcReqFailNotify		3.1.1751.2.18.8.4.9
Response : The PVC connection request between two variable-bit rate interfaces has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmPvcVccSetupNotify		3.1.1751.2.18.8.4.10
Response : The PVC VCC connection between two atm interfaces has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmPvcVpcSetupNotify		3.1.1751.2.18.8.4.11
Response : The PVC VPC connection between two atm interfaces has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

ipAtmAppPvcVccSetupNotify		3.1.1751.2.18.8.4.12
Response : The PVC VCC connection between in-band management and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmAtmPvcVccSetupNotify		3.1.1751.2.18.8.4.13
Response : The PVC VCC connection between a circuit emulation interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmPvcVccSetupNotify		3.1.1751.2.18.8.4.14
Response : The PVC VCC connection between a variable-bit rate interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmPvcVccSetupNotify		3.1.1751.2.18.8.4.15
Response : The PVC VCC connection between a frame-relay interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

frFrPvcSetupNotify		3.1.1751.2.18.8.4.16
Response : The PVC connection between two frame-relay interfaces has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmCirEmPvcSetupNotify		3.1.1751.2.18.8.4.17
Response : The PVC connection between two circuit-emulation interfaces has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrVbrPvcSetupNotify		3.1.1751.2.18.8.4.18
Response : The PVC connection between two variable-bit rate interfaces has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmPvcVccTearDownNotify		3.1.1751.2.18.8.4.19
Response : The PVC VCC connection between two atm interfaces has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmPvcVpcTearDownNotify		3.1.1751.2.18.8.4.20
Response : The PVC VPC connection between two atm interfaces has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

ipAtmAppPvcVccTearDownNotify		3.1.1751.2.18.8.4.21
Response : The PVC VCC connection between in-band management and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmAtmPvcVccTearDownNotify		3.1.1751.2.18.8.4.22
Response : The PVC VCC connection between a circuit-emulation interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmPvcVccTearDownNotify		3.1.1751.2.18.8.4.23
Response : The PVC VCC connection between a variable-bit rate interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmPvcVccTearDownNotify		3.1.1751.2.18.8.4.24
Response : The PVC VCC connection between a frame-relay interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

frFrPvcTearDownNotify		3.1.1751.2.18.8.4.25
Response : The PVC connection between two frame-relay interfaces has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmCirEmPvcTearDownNotify		3.1.1751.2.18.8.4.26
Response : The PVC connection between two circuit-emulation interfaces has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrVbrPvcTearDownNotify		3.1.1751.2.18.8.4.27
Response : The PVC connection between two variable-bit rate interfaces has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeBridgePvcReqFailNotify		3.1.1751.2.18.8.4.28
Response : The PVC connection request between two bridge interfaces has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeBridgePvcSetupNotify		3.1.1751.2.18.8.4.29
Response : The PVC connection between two bridge interfaces has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeBridgePvcTearDownNotify		3.1.1751.2.18.8.4.30
Response : The PVC connection between two bridge interfaces has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeAtmPvcVccReqFailNotify		3.1.1751.2.18.8.4.31
Response : The PVC VCC connection request between a bridge interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeAtmPvcVccSetupNotify		3.1.1751.2.18.8.4.32
Response : The PVC VCC connection between a bridge interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeAtmPvcVccTearDownNotify		3.1.1751.2.18.8.4.33
Response : The PVC VCC connection between a bridge interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

cellTestReqFailNotify		3.1.1751.2.18.8.4.34
Response : The PVC connection request has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

lmiDlciStatusNotify		3.1.1751.2.18.8.4.35
Response : Indicates the end-to-end status of the PVC of which this DLCI is a segment of.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmAtmBkPvcVccReqFailNotify		3.1.1751.2.18.8.4.36
Response : The DHPVC VCC backup connection request between a circuit emulation interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmAtmBkPvcVccSetupNotify		3.1.1751.2.18.8.4.37
Response : The DHPVC VCC backup connection between a circuit emulation interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmAtmBkPvcVccTearDownNotify		3.1.1751.2.18.8.4.38
Response : The DHPVC VCC backup connection between a circuit-emulation interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmBkPvcVccReqFailNotify		3.1.1751.2.18.8.4.39
Response : The DHPVC VCC backup connection request between a variable-bit rate interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmBkPvcVccSetupNotify		3.1.1751.2.18.8.4.40
Response : The DHPVC VCC backup connection between a variable-bit rate interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmBkPvcVccTearDownNotify		3.1.1751.2.18.8.4.41
Response : The DHPVC VCC backup connection between a variable-bit rate interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmBkPvcVccReqFailNotify		3.1.1751.2.18.8.4.42
Response : The DHPVC VCC backup connection request between an atm interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmBkPvcVccSetupNotify		3.1.1751.2.18.8.4.43
Response : The DHPVC VCC backup connection between an atm interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmBkPvcVccTearDownNotify		3.1.1751.2.18.8.4.44
Response : The DHPVC VCC backup connection between an atm interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmBkPvcVccReqFailNotify		3.1.1751.2.18.8.4.45
Response : The DHPVC VCC backup connection request between a frame relay interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmBkPvcVccSetupNotify		3.1.1751.2.18.8.4.46
Response : The DHPVC VCC backup connection between a frame relay interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmBkPvcVccTearDownNotify		3.1.1751.2.18.8.4.47
Response : The DHPVC VCC backup connection between a frame relay interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmBkPvcVpcReqFailNotify		3.1.1751.2.18.8.4.48
Response : The DHPVC VPC backup connection request between an atm interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmBkPvcVpcSetupNotify		3.1.1751.2.18.8.4.49
Response : The DHPVC VPC backup connection between an atm interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmBkPvcVpcTearDownNotify		3.1.1751.2.18.8.4.50
Response : The DHPVC VPC backup connection between an atm interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeAtmBkPvcVccReqFailNotify		3.1.1751.2.18.8.4.51
Response : The DHPVC VCC backup connection request between a bridge interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeAtmBkPvcVccSetupNotify		3.1.1751.2.18.8.4.52
Response : The DHPVC VCC backup connection between a bridge interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

bridgeAtmBkPvcVccTearDownNotify		3.1.1751.2.18.8.4.53
Response : The DHPVC VCC backup connection between a bridge interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

ipAtmBkAppPvcVccReqFailNotify		3.1.1751.2.18.8.4.54
Response : The DHPVC VCC backup connection request between an in-band management interface and an atm interface has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

ipAtmBkAppPvcVccSetupNotify		3.1.1751.2.18.8.4.55
Response : The DHPVC VCC backup connection between an in-band management interface and an atm interface has been created.
Status: current	Access: read-write
NOTIFICATION-TYPE

ipAtmBkAppPvcVccTearDownNotify		3.1.1751.2.18.8.4.56
Response : The DHPVC VCC backup connection between an in-band management interface and an atm interface has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmAtmSpvcVccSetUpNotify		3.1.1751.2.18.8.4.57
Response : Notification that a SPVC connection between CE and ATM endpoints has been made successfully. Return values - A-side interfaceIndex B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmSpvcVccSetUpNotify		3.1.1751.2.18.8.4.58
Response : Notification that a SPVC connection between TE and ATM endpoints has been made successfully. Return values - A-side interfaceIndex B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

atmSpvcVccSetUpNotify		3.1.1751.2.18.8.4.59
Response : Notification that a SPVC connection between ATM and ATM endpoints has been made successfully. Return values - A-side interfaceIndex A-side vpi/vci B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

cirEmAtmSpvcVccTearDownNotify		3.1.1751.2.18.8.4.60
Response : Notification that a SPVC connection between CE and ATM endpoints has been deleted. Return values - A-side interfaceIndex B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmSpvcVccTearDownNotify		3.1.1751.2.18.8.4.61
Response : Notification that a SPVC connection between TE and ATM endpoints has been deleted. Return values - A-side interfaceIndex B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

atmSpvcVccTearDownNotify		3.1.1751.2.18.8.4.62
Response : Notification that a SPVC connection between ATM and ATM endpoints has been deleted. Return values - A-side interfaceIndex A-side vpi/vci B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

oamTestReqFailNotify		3.1.1751.2.18.8.4.63
Response : OAM loopback test request has failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

oamActDeactResultNotify		3.1.1751.2.18.8.4.64
Response : the final status of oam Activation-Deactivation request.
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmSpvcVccSetUpNotify		3.1.1751.2.18.8.4.65
Response : Notification that a SPVC connection between FR and ATM endpoints has been made successfully. Return values - A-side interfaceIndex A-side dlci B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

frAtmSpvcVccTearDownNotify		3.1.1751.2.18.8.4.66
Response : Notification that a SPVC connection between FR and ATM endpoints has been deleted. Return values - A-side interfaceIndex A-side dlci B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvcVccSetUpNotify		3.1.1751.2.18.8.4.67
Response : Notification that a SPVC connection between ATM and ATM endpoints has been made successfully. Return values - A-side interfaceIndex A-side vpi/vci Remote NSAP address B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvcVccTearDownNotify		3.1.1751.2.18.8.4.68
Response : Notification that a SPVC connection between ATM and ATM endpoints has been deleted. Return values - A-side interfaceIndex A-side vpi/vci Remote NSAP address B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

cirAtmSpvcVccSetUpNotify		3.1.1751.2.18.8.4.69
Response : Notification that a SPVC connection between CE and ATM endpoints has been made successfully. Return values - A-side interfaceIndex Remote NSAP address B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

cirAtmSpvcVccTearDownNotify		3.1.1751.2.18.8.4.70
Response : Notification that a SPVC connection between CE and ATM endpoints has been deleted. Return values - A-side interfaceIndex Remote NSAP address B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmSpvcSetUpNotify		3.1.1751.2.18.8.4.71
Response : Notification that a SPVC connection between TE and ATM endpoints has been made successfully. Return values - A-side interfaceIndex Remote NSAP address B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

vbrAtmSpvcTearDownNotify		3.1.1751.2.18.8.4.72
Response : Notification that a SPVC connection between TE and ATM endpoints has been deleted. Return values - A-side interfaceIndex Remote NSAP address B-side interfaceIndex B-side vpi/vci
Status: current	Access: read-write
NOTIFICATION-TYPE

aal2TrunkConfigSetupNotify		3.1.1751.2.18.8.4.73
Response : The PVC VCC connection for aal2 trunk
Status: current	Access: read-write
NOTIFICATION-TYPE

aal2TrunkConfigTearDownNotify		3.1.1751.2.18.8.4.74
Response : The PVC VCC AAL2 Trunk has been deleted
Status: current	Access: read-write
NOTIFICATION-TYPE

aal2TrunkConfigReqFailNotify		3.1.1751.2.18.8.4.75
Response : The PVC VCC aal2 trunk could not be setup
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303Aal2PvcConfigReqFailNotify		3.1.1751.2.18.8.4.76
Response : The GR303 PVC VCC on aal2 trunk could not be setup
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303Aal2PvcSetUpNotify		3.1.1751.2.18.8.4.77
Response : Notification that a monitor connection between Gr303 call ref and ATM AAL2 CID has been made successfully.
Status: current	Access: read-write
NOTIFICATION-TYPE

gr303Aal2PvcTearDownNotify		3.1.1751.2.18.8.4.78
Response : Notification that a monitor connection between Gr303 call ref and ATM AAL2 CID has been deleted
Status: current	Access: read-write
NOTIFICATION-TYPE

dhpvcChangeNotify		3.1.1751.2.18.8.4.79
This will indicate the changes in a dual home pvc. This will have 2 indications. One is when there is a switchover which indicate the last state and the new one (eg Prim To Bkup) Secondly there will also be an indication when there is a state change which will indicate the new state only (eg Primary is Active and in No Fail Condition and Backup is Passive and in Fail Condition). In case of state change the traffic path is not changed but it indicates the state of the passive path.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvcVpcSetUpNotify		3.1.1751.2.18.8.4.80
Response : Notification that a SPVP connection between ATM and ATM endpoints has been made successfully.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmAtmSpvcVpcTearDownNotify		3.1.1751.2.18.8.4.81
Response : Notification that a SPVP connection between ATM and ATM endpoints has been deleted.
Status: current	Access: read-write
NOTIFICATION-TYPE

iptResultNotify		3.1.1751.2.18.8.4.82
Response : the final status of interface protection request.
Status: current	Access: read-write
NOTIFICATION-TYPE

pgtResultNotify		3.1.1751.2.18.8.4.83
Response : the final status of interface protection group request.
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingSigVccSetUpNotify		3.1.1751.2.18.8.4.84
Response : Notification that a ATM Trunking Signalling VCC has been setup successfully. Return values - atmTrunkingSigVccRmtIWFIdentifier atmTrunkingSigVccIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingSigVccTearDownNotify		3.1.1751.2.18.8.4.85
Response : Notification that a ATM Trunking Signalling VCC has been torn down successfully. Return values - atmTrunkingSigVccRmtIWFIdentifier atmTrunkingSigVccIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingBrVccSetUpNotify		3.1.1751.2.18.8.4.86
Response : Notification that a ATM Trunking Bearer VCC has been setup successfully. Return values - atmTrunkingBrVccRmtIWFIdentifier atmTrunkingBrVccIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE

atmTrunkingBrVccTearDownNotify		3.1.1751.2.18.8.4.87
Response : Notification that a ATM Trunking Bearer VCC has been torn down successfully. Return values - atmTrunkingBrVccRmtIWFIdentifier atmTrunkingBrVccIdentifier
Status: current	Access: read-write
NOTIFICATION-TYPE