AI-AP-MIB

File: AI-AP-MIB.mib (147659 bytes)

Imported modules

SNMPv2-TC	SNMPv2-SMI	SNMPv2-CONF
ARUBA-MIB

Imported symbols

TEXTUAL-CONVENTION	MODULE-IDENTITY	OBJECT-TYPE
snmpModules	Integer32	Counter32
Counter64	IpAddress	TimeTicks
NOTIFICATION-TYPE	DisplayString	PhysAddress
TimeInterval	RowStatus	StorageType
TestAndIncr	MacAddress	TruthValue
DateAndTime	OBJECT-GROUP	aiEnterpriseMibModules

Defined Types

ArubaEnableValue
Represents a Flag which is either Enabled or Disabled.
TEXTUAL-CONVENTION
	INTEGER	enabled(1), disabled(2)

ArubaFrameType
Represents the Frame type.
TEXTUAL-CONVENTION
	INTEGER	associateRequest(0), associateResponse(1), reassociateRequest(2), reassociateResponse(3), probeRequest(4), probeResponse(5), beacon(8), atim(9), disassociate(10), auth(11), deauth(12)

ArubaPhyType
Represents the PHY-type of the access point or client. Wired clients will show 'wired' in user MIB entries.
TEXTUAL-CONVENTION
	INTEGER	dot11a(1), dot11b(2), dot11g(3), dot11ag(4), wired(5)

ArubaHTMode
Represents the HT status of the access point or client.
TEXTUAL-CONVENTION
	INTEGER	none(1), ht20(2), ht40(3)

ArubaHTExtChannel
Represents the extension channel offset relative to the current channel.
TEXTUAL-CONVENTION
	INTEGER	none(1), above(2), below(3)

ArubaMonEncryptionType
Represents the encryption type supported by the access point.
TEXTUAL-CONVENTION
	INTEGER	open(0), wep(1), wpa(2), wpa2(3)

ArubaMonEncryptionCipher
Represents the WPA encryption cipher supported by the access point.
TEXTUAL-CONVENTION
	INTEGER	none(0), wep40(1), wep104(2), tkip(3), aesccmp(4), other(5)

ArubaMonAuthAlgorithm
Represents the WPA authentication algorithm supported by the access point.
TEXTUAL-CONVENTION
	INTEGER	none(0), psk(1), dot1x(2), other(3)

ArubaSwitchRole
Represents the role of the controller
TEXTUAL-CONVENTION
	INTEGER	master(1), local(2), backupmaster(3)

ArubaSupportStatus
Represents if a feature is supported or unsupported.
TEXTUAL-CONVENTION
	INTEGER	unsupported(1), supported(2)

ArubaActiveState
Represents if a feature is active or inactive.
TEXTUAL-CONVENTION
	INTEGER	active(1), inactive(2)

ArubaACLDomain
Represents both the source and destination to which an ACL rule will be applied.
TEXTUAL-CONVENTION
	INTEGER	alias(1), any(2), user(3), host(4), network(5)

ArubaACLNetworkServiceType
Represents the network service in an ACL Rule.
TEXTUAL-CONVENTION
	INTEGER	alias(1), any(2), tcp(3), udp(4), protocol(5)

ArubaACLAction
Represents the Actions in an ACL rule.
TEXTUAL-CONVENTION
	INTEGER	deny(1), permit(2), srcNAT(3), dstNAT(4), redirect(5)

ArubaDaysOfWeek
Represents the Actions in an ACL rule.
TEXTUAL-CONVENTION
	INTEGER	sun(1), mon(2), tue(3), wed(4), thu(5), fri(6), sat(7)

ArubaAuthenticationMethods
Authentication Method.
TEXTUAL-CONVENTION
	INTEGER	none(0), web(1), mac(2), vpn(3), dot1x(4), kerberos(5), secureId(7), pubcookie(15), xSec(16), xSecMachine(17), via-vpn(28), other(255)

ArubaSubAuthenticationMethods
Sub Authentication Method (e.g. EAP type).
TEXTUAL-CONVENTION
	INTEGER	authPAP(1), authCHAP(2), authMSCHAP(3), authMSCHAPv2(4), eapTLS(5), eapTTLS(6), eapLEAP(7), eapMD5(8), eapPEAP(9)

ArubaEncryptionType
Encryption Method.
TEXTUAL-CONVENTION
	INTEGER	none(0), static-wep(1), dynamic-wep(2), wpa-psk-tkip(3), wpa-tkip(4), wpa-psk-aes(5), wpa-aes(6), wpa2-psk-tkip(7), wpa2-tkip(8), wpa2-psk-aes(9), wpa2-aes(10), xSec(11), bSec-128(12), bSec-256(13), aes-128-cmac(14), unknown(15)

ArubaUserForwardMode
User Forwarding Mode.
TEXTUAL-CONVENTION
	INTEGER	tunnel-encrypted(0), bridge(1), tunnel-decrypted(2), split-tunnel(3)

ArubaRogueApType
Represents the Rogue AP Type.
TEXTUAL-CONVENTION
	INTEGER	valid(1), interfering(2), unsecure(3), dos(4), unknown(5), knownInterfering(6), suspectedUnsecure(7)

ArubaAPMatchType
Represents the match type of a suspected rogue AP.
TEXTUAL-CONVENTION
	INTEGER	unknown(0), configuredWiredMac(1), ethernetWiredMac(2), apWiredMac(3), externalWiredMac(4), manual(5), baseBSSIDOverride(6), mms(7), ethernetGatewayWiredMac(8), classificationDisabled(9), apBSSID(10), propagatedEthernetWiredMac(11), apRule(12), systemWiredMac(13), systemGatewayMac(14)

ArubaAPMatchMethod
Represents the match method of a suspected rogue AP.
TEXTUAL-CONVENTION
	INTEGER	notApplicable(0), exactMatch(1), plusOneMatch(2), minusOneMatch(3), ouiMatch(4)

ArubaStationType
Represents the station type.
TEXTUAL-CONVENTION
	INTEGER	valid(1), interfering(2), dos(3)

ArubaEncryptionMethods
Represents the Actions in an ACL rule.
TEXTUAL-CONVENTION
	BITS	disabled(0), static-wep(1), dynamic-wep(2), static-wpa(3), dynamic-wpa(4), wpa2-psk-aes(5), wpa2-8021x-aes(6), wpa2PreAuth(7), xsec(8), wpa-psk-aes(9), wpa-aes(10), wpa2-psk-tkip(11), wpa2-8021x-tkip(12)

ArubaHashAlgorithms
Represents the Actions in an ACL rule.
TEXTUAL-CONVENTION
	INTEGER	md5(1), sha(2)

ArubaVlanValidRange
Represents the Valid Vlan Id Range.
TEXTUAL-CONVENTION
	INTEGER	1..4095

ArubaPortMode
Represents the controller port mode.
TEXTUAL-CONVENTION
	INTEGER	access(1), dot1q(2)

ArubaDot1dState
Represents the controller port spanning tree state.
TEXTUAL-CONVENTION
	INTEGER	disabled(1), blocked(2), listening(3), learning(4), forwarding(5)

ArubaPoeState
Represents the POE mode.
TEXTUAL-CONVENTION
	INTEGER	disabled(1), enabled(2), enabledCisco(3), notAvailable(4)

ArubaCardType
Type of the hardware module.
TEXTUAL-CONVENTION
	INTEGER	lc1(1), lc2(2), sc1(3), sc2(4), sw2400(5), sw800(6), sw200(7), m3mk1(8), sw3200(9), sw3400(10), sw3600(11), sw650(12), sw651(13), reserved1(14), reserved2(15), sw620(16)

ArubaESIServerMode
The mode of the ESI server.
TEXTUAL-CONVENTION
	INTEGER	bridged(1), routed(2), nat(3)

ArubaESIServerStatus
The status of the ESI server.
TEXTUAL-CONVENTION
	INTEGER	up(1), down(2)

ArubaIfType
The type of interface referred to by the value of ifIndex.
TEXTUAL-CONVENTION
	INTEGER	port(1), vlan(2), tunnel(3), loopback(4)

ArubaVoipProtocolType
The type of VoIP protocols supported.
TEXTUAL-CONVENTION
	INTEGER	sccp(1), svp(2), vocera(3), sip(4), unknown(10)

ArubaAccessPointMode
The mode of the access point.
TEXTUAL-CONVENTION
	INTEGER	airMonitor(1), accessPoint(2), accessPointAndMonitor(3), meshPortal(4), meshPoint(5), rfprotectSensor(6), spectrumSensor(7)

ArubaAuthServerType
The type of the auth server.
TEXTUAL-CONVENTION
	INTEGER	internaldb(1), radius(2), ldap(3), kerberos(4), tacacs(5)

ArubaAddressType
Address Type.
TEXTUAL-CONVENTION
	INTEGER	srcAddress(1), dstAddress(2), bssid(3)

ArubaBlackListReason
Black List Reason.
TEXTUAL-CONVENTION
	INTEGER	userDefined(1), mitmAttack(2), authFailure(3), pingFlood(4), sessionFlood(5), synFlood(6), sessionBlacklist(7), ipSpoofing(8), esiBlacklist(9), other(100)

ArubaDBType
DataBase Type.
TEXTUAL-CONVENTION
	INTEGER	mssql(1), mysql(2)

ArubaVrrpState
DataBase Type.
TEXTUAL-CONVENTION
	INTEGER	initialize(1), backup(2), master(3)

ArubaOperStateValue
Represents Operational state of an interface.
TEXTUAL-CONVENTION
	INTEGER	up(1), down(2), testing(3)

ArubaAntennaSetting
Represents the status of the external antenna.
TEXTUAL-CONVENTION
	INTEGER	notPresent(1), enabled(2), disabled(3)

ArubaAPStatus
The status of the access point.
TEXTUAL-CONVENTION
	INTEGER	up(1), down(2)

ArubaPortSpeed
Port Speed.
TEXTUAL-CONVENTION
	INTEGER	speed10Mbps(1), speed100Mbps(2), speed1000Mbps(3), speedAuto(4), speed10Gbps(5)

ArubaPortDuplex
Port Duplexity.
TEXTUAL-CONVENTION
	INTEGER	half(1), full(2), auto(3)

ArubaPortType
Port Type.
TEXTUAL-CONVENTION
	INTEGER	fastethernet(1), gigabitethernet(2), xgigabitethernet(3)

ArubaEnet1Mode
Represents the Mode of the Ethernet port on the Access Point
TEXTUAL-CONVENTION
	INTEGER	activeStandby(1), tunnel(2), bridge(3), notApplicable(4), split(5)

ArubaUnprovisionedStatus
Represents whether the AP is provisioned or not.
TEXTUAL-CONVENTION
	INTEGER	yes(1), no(2)

ArubaMonitorMode
Represents whether the AP has any radios dedicated to monitoring.
TEXTUAL-CONVENTION
	INTEGER	unknown(0), all(1), none(2), mixed(3)

ArubaConfigurationState
Configuration Transfer Types.
TEXTUAL-CONVENTION
	INTEGER	success(1), error(2)

ArubaConfigurationChangeType
Configuration Change Types.
TEXTUAL-CONVENTION
	INTEGER	create(1), delete(2), modify(3)

ArubaCallStates
The Call state.
TEXTUAL-CONVENTION
	INTEGER	idle(0), initiated(1), connecting(2), delivered(3), connected(4), offered(5), alerting(6), releasing(7), cancelling(8), challenging(9), transient(10), blockwait(11), succ(12), fail(13), aborted(14), blocked(15)

ArubaVoipProtocol
VoIP protocol used
TEXTUAL-CONVENTION
	INTEGER	sccp(1), svp(2), vocera(3), sip(9), ua(11)

ArubaVoipRegState
VoIP registered state
TEXTUAL-CONVENTION
	INTEGER	unknown(0), registering(1), unregistering(2), challenge(3), registered(4), unregistered(5)

ArubaVoiceCdrDirection
VoIP CDR direction
TEXTUAL-CONVENTION
	INTEGER	og(0), ic(1)

ArubaVoiceCacBit
Voice CAC bit flags
TEXTUAL-CONVENTION
	BITS	cacActiveLoadBalancing(0), cacHighCapThresholdReached(1), cacHandRsrvThresholdReached(2), cacPeakCapacityReached(3)

ArubaMeshRole
Mesh role
TEXTUAL-CONVENTION
	INTEGER	nonmesh(0), point(1), portal(2)

ArubaHTRate
Represents HT rate
TEXTUAL-CONVENTION
	INTEGER	unknown(0), ht6dot5(1), ht13(2), ht13dot5(3), ht15(4), ht19dot5(5), ht26(6), ht27(7), ht30(8), ht39(9), ht40dot5(10), ht45(11), ht52(12), ht54(13), ht58dot5(14), ht60(15), ht65(16), ht78(17), ht81(18), ht90(19), ht104(20), ht108(21), ht117(22), ht120(23), ht121dot5(24), ht130(25), ht135(26), ht150(27), ht162(28), ht180(29), ht216(30), ht240(31), ht243(32), ht270(33), ht300(34)

ArubaUSBStatus
USB device status
TEXTUAL-CONVENTION
	INTEGER	unknown(0), notPresent(1), inactive(2), active(3)

ArubaARMChangeReason
The reason for ARM based change.
TEXTUAL-CONVENTION
	INTEGER	radarDetected(1), radarCleared(2), txHang(3), txHangClear(4), fortyMhzIntol(5), cancel40mhzIntol(6), fortyMhzAlign(7), armInterference(8), armInvalidCh(9), armErrorThresh(10), armNoiseThresh(11), armEmptyCh(12), armRogueCont(13), armDecreasePower(14), armIncreasePower(15), armTurnOffRadio(16), armTurnOnRadio(17)

ArubaAPMasterStatus
AP status as seen by the master controller (used to indicate a status change).
TEXTUAL-CONVENTION
	INTEGER	up(1), down(2), move(3)

ArubaAPUplinkType
AP uplink type
TEXTUAL-CONVENTION
	INTEGER	ethernet(1), usb(2), pppoe(3), wifi(4)

ArubaAPUplinkChangeReason
Used to specify the reason for AP uplink change. linkFailure - The uplink went down vpnFailure - VPN tunnel could not be sustained using the uplink preemption - The uplink was pre-empted by a higher-priority uplink
TEXTUAL-CONVENTION
	INTEGER	linkFailure(1), vpnFailure(2), preemption(3), internetFailover(4)

ArubaPortalServerDownReason
Used to specify the reason for Portal server down. connectFail - Connect Portal server fail
TEXTUAL-CONVENTION
	INTEGER	connectFail(1)

AiWlanSSIDEntry
SEQUENCE
	aiSSIDIndex	Integer32
	aiSSID	DisplayString
	aiSSIDStatus	INTEGER

AiAccessPointEntry
SEQUENCE
	aiAPMACAddress	MacAddress
	aiAPName	DisplayString
	aiAPIPAddress	IpAddress
	aiAPSerialNum	DisplayString
	aiAPModel	OBJECT IDENTIFIER
	aiAPModelName	DisplayString
	aiAPCPUUtilization	Integer32
	aiAPMemoryFree	Integer32
	aiAPUptime	TimeTicks
	aiAPTotalMemory	Integer32
	aiAPStatus	INTEGER

AiRadioEntry
SEQUENCE
	aiRadioAPMACAddress	MacAddress
	aiRadioIndex	Integer32
	aiRadioMACAddress	MacAddress
	aiRadioChannel	Integer32
	aiRadioTransmitPower	Integer32
	aiRadioNoiseFloor	Integer32
	aiRadioUtilization4	Integer32
	aiRadioUtilization64	Integer32
	aiRadioTxTotalFrames	Counter32
	aiRadioTxMgmtFrames	Counter32
	aiRadioTxDataFrames	Counter32
	aiRadioTxDataBytes	Counter32
	aiRadioTxDrops	Counter32
	aiRadioRxTotalFrames	Counter32
	aiRadioRxDataFrames	Counter32
	aiRadioRxDataBytes	Counter32
	aiRadioRxMgmtFrames	Counter32
	aiRadioRxBad	Counter32
	aiRadioPhyEvents	Counter32
	aiRadioStatus	INTEGER

AiWlanEntry
SEQUENCE
	aiWlanAPMACAddress	MacAddress
	aiWlanIndex	Integer32
	aiWlanESSID	DisplayString
	aiWlanMACAddress	MacAddress
	aiWlanTxTotalFrames	Counter32
	aiWlanTxDataFrames	Counter32
	aiWlanTxDataBytes	Counter32
	aiWlanRxTotalFrames	Counter32
	aiWlanRxDataFrames	Counter32
	aiWlanRxDataBytes	Counter32

AiClientEntry
SEQUENCE
	aiClientMACAddress	MacAddress
	aiClientWlanMACAddress	MacAddress
	aiClientIPAddress	IpAddress
	aiClientAPIPAddress	IpAddress
	aiClientName	DisplayString
	aiClientOperatingSystem	DisplayString
	aiClientSNR	Integer32
	aiClientTxDataFrames	Counter32
	aiClientTxDataBytes	Counter32
	aiClientTxRetries	Counter32
	aiClientTxRate	Integer32
	aiClientRxDataFrames	Counter32
	aiClientRxDataBytes	Counter32
	aiClientRxRetries	Counter32
	aiClientRxRate	Integer32
	aiClientUptime	TimeTicks

AiVoiceClientEntry
SEQUENCE
	aiClientMac	MacAddress
	aiClientIP	IpAddress
	aiClientAPMac	MacAddress
	aiClientAPName	DisplayString

Defined Values

aiMIB		1.3.6.1.4.1.14823.2.3.3.1
This MIB is for managing Aruba Instant WLAN
MODULE-IDENTITY

aiInfoGroup		1.3.6.1.4.1.14823.2.3.3.1.1
OBJECT IDENTIFIER

aiStateGroup		1.3.6.1.4.1.14823.2.3.3.1.2
OBJECT IDENTIFIER

aiManagedInfoGroup		1.3.6.1.4.1.14823.2.3.3.1.3
OBJECT IDENTIFIER

aiVirtualControllerKey		1.3.6.1.4.1.14823.2.3.3.1.1.1
Unique Virtual Controller key
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

aiVirtualControllerName		1.3.6.1.4.1.14823.2.3.3.1.1.2
Virtual Controller name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

aiVirtualControllerOrganization		1.3.6.1.4.1.14823.2.3.3.1.1.3
Virtual Controller organization
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

aiVirtualControllerVersion		1.3.6.1.4.1.14823.2.3.3.1.1.4
Software Version
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

aiVirtualControllerIPAddress		1.3.6.1.4.1.14823.2.3.3.1.1.5
Virtual Controller IP Address. If this is not set, returns 0.0.0.0
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

aiMasterIPAddress		1.3.6.1.4.1.14823.2.3.3.1.1.6
IP Address of AP where virtual controller software is active
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

aiWlanSSIDTable		1.3.6.1.4.1.14823.2.3.3.1.1.7
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AiWlanSSIDEntry

aiWlanSSIDEntry		1.3.6.1.4.1.14823.2.3.3.1.1.7.1
Status: current	Access: not-accessible
OBJECT-TYPE
	AiWlanSSIDEntry

aiSSIDIndex		1.3.6.1.4.1.14823.2.3.3.1.1.7.1.1
SSID Index
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiSSID		1.3.6.1.4.1.14823.2.3.3.1.1.7.1.2
SSID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..64)

aiSSIDStatus		1.3.6.1.4.1.14823.2.3.3.1.1.7.1.3
Indicates the whether the SSID is enabled(0) or disabled(1)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enable(0), disable(1)

aiAccessPointTable		1.3.6.1.4.1.14823.2.3.3.1.2.1
This contains all access points connected to the virtual controller. This table is empty on AP where virtual controller is not active
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AiAccessPointEntry

aiAccessPointEntry		1.3.6.1.4.1.14823.2.3.3.1.2.1.1
Status: current	Access: not-accessible
OBJECT-TYPE
	AiAccessPointEntry

aiAPMACAddress		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.1
Access Point MAC Address
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

aiAPName		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.2
Access Point name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..64)

aiAPIPAddress		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.3
Access Point IP Address
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

aiAPSerialNum		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.4
Access Point Serial Number
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..64)

aiAPModel		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.5
Access Point System OID
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

aiAPModelName		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.6
Access Point Model Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

aiAPCPUUtilization		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.7
Access Point CPU Utilization
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiAPMemoryFree		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.8
Amount of memory free in the access point in bytes
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiAPUptime		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.9
Access Point uptime
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

aiAPTotalMemory		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.10
Total amount of memory available in the AP in bytes
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiAPStatus		1.3.6.1.4.1.14823.2.3.3.1.2.1.1.11
Indicates the Access Point Status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

aiRadioTable		1.3.6.1.4.1.14823.2.3.3.1.2.2
This table contains all radios of all access points connected to the virtual controller. This table is indexed by Access Point MAC Address and radio number
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AiRadioEntry

aiRadioEntry		1.3.6.1.4.1.14823.2.3.3.1.2.2.1
Status: current	Access: not-accessible
OBJECT-TYPE
	AiRadioEntry

aiRadioAPMACAddress		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.1
MAC Address of access point where this radio is active
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

aiRadioIndex		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.2
Radio number
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiRadioMACAddress		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.3
Radio MAC Address
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

aiRadioChannel		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.4
Radio channel. First byte contains primary channel and first two bits on second byte contains indicator for secondary channel. If first two bits of second byte is 0, it is a 20MHz channel. If first two bits of second byte is 01, secondary channel is above primary channel, if first two bits of second by is 10, secondary channel is below the primary channel.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiRadioTransmitPower		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.5
Radio transmit power
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiRadioNoiseFloor		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.6
Radio noise floor in dBm
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiRadioUtilization4		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.7
Radio channel utilization 4 second average
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiRadioUtilization64		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.8
Radio channel utilization 64 second average
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiRadioTxTotalFrames		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.9
Total transmitted frames
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioTxMgmtFrames		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.10
Transmitted management frames
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioTxDataFrames		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.11
Transmitted data frames
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioTxDataBytes		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.12
Transmitted data bytes
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioTxDrops		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.13
Total frames dropped during transmission
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioRxTotalFrames		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.14
Total received frames
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioRxDataFrames		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.15
Received data frames
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioRxDataBytes		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.16
Received data bytes
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioRxMgmtFrames		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.17
Received management frames
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioRxBad		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.18
Frames received in error
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioPhyEvents		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.19
Number of phy events that indicates frames not received because of interference
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiRadioStatus		1.3.6.1.4.1.14823.2.3.3.1.2.2.1.20
Radio state of AP - UP/DOWN
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

aiWlanTable		1.3.6.1.4.1.14823.2.3.3.1.2.3
This table contains all BSSIDs active on this virtual controller. This table is indexed by Access Point MAC Address and a WLAN Index
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AiWlanEntry

aiWlanEntry		1.3.6.1.4.1.14823.2.3.3.1.2.3.1
Status: current	Access: not-accessible
OBJECT-TYPE
	AiWlanEntry

aiWlanAPMACAddress		1.3.6.1.4.1.14823.2.3.3.1.2.3.1.1
MAC Address of access point where WLAN is active
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

aiWlanIndex		1.3.6.1.4.1.14823.2.3.3.1.2.3.1.2
Index of WLAN. This is a unique index assigned to the WLAN active on the access point.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiWlanESSID		1.3.6.1.4.1.14823.2.3.3.1.2.3.1.3
ESSID of WLAN
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

aiWlanMACAddress		1.3.6.1.4.1.14823.2.3.3.1.2.3.1.4
BSSID of WLAN
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

aiWlanTxTotalFrames		1.3.6.1.4.1.14823.2.3.3.1.2.3.1.5
Total transmitted frames
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiWlanTxDataFrames		1.3.6.1.4.1.14823.2.3.3.1.2.3.1.6
Transmitted data frames
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiWlanTxDataBytes		1.3.6.1.4.1.14823.2.3.3.1.2.3.1.7
Transmitted data bytes
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiWlanRxTotalFrames		1.3.6.1.4.1.14823.2.3.3.1.2.3.1.8
Total received frames
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiWlanRxDataFrames		1.3.6.1.4.1.14823.2.3.3.1.2.3.1.9
Received data frames
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiWlanRxDataBytes		1.3.6.1.4.1.14823.2.3.3.1.2.3.1.10
Received data bytes
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiClientTable		1.3.6.1.4.1.14823.2.3.3.1.2.4
This table contains information about all clients connected to the virtual controller. When a client roams from one access point to another, all counters in this table are reset to 0. aiClientUptime also get reset on a mobility event
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AiClientEntry

aiClientEntry		1.3.6.1.4.1.14823.2.3.3.1.2.4.1
Status: current	Access: not-accessible
OBJECT-TYPE
	AiClientEntry

aiClientMACAddress		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.1
MAC Address of client
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

aiClientWlanMACAddress		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.2
BSSID of WLAN where client is associated
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

aiClientIPAddress		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.3
Client IP Address
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

aiClientAPIPAddress		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.4
Associated Access Point IP Address
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

aiClientName		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.5
Name of user using the client
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

aiClientOperatingSystem		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.6
Client operating system
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

aiClientSNR		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.7
Signal to noise ratio of client connection to the access point
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiClientTxDataFrames		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.8
Total frames transmitted by the client
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiClientTxDataBytes		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.9
Total bytes transmitted by the client
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiClientTxRetries		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.10
Total number of retry frames transmitted by the client
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiClientTxRate		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.11
Transmit rate of client in mbps
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiClientRxDataFrames		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.12
Total frames received by the client
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiClientRxDataBytes		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.13
Total bytes received by the client
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiClientRxRetries		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.14
Total number of retry frames received by the client
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

aiClientRxRate		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.15
Receive rate of client in mbps
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

aiClientUptime		1.3.6.1.4.1.14823.2.3.3.1.2.4.1.16
Client uptime. On mobility event all counters are reset to 0 and uptime gets reset to 0.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

aiVoiceClientTable		1.3.6.1.4.1.14823.2.3.3.1.2.5
Table of voice clients
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AiVoiceClientEntry

aiVoiceClientEntry		1.3.6.1.4.1.14823.2.3.3.1.2.5.1
Entry of a voice client
Status: current	Access: not-accessible
OBJECT-TYPE
	AiVoiceClientEntry

aiClientMac		1.3.6.1.4.1.14823.2.3.3.1.2.5.1.1
MAC address of voice client
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

aiClientIP		1.3.6.1.4.1.14823.2.3.3.1.2.5.1.2
IP address of voice client
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

aiClientAPMac		1.3.6.1.4.1.14823.2.3.3.1.2.5.1.3
MAC address of AP on which voice client is associated currently
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

aiClientAPName		1.3.6.1.4.1.14823.2.3.3.1.2.5.1.4
Name of AP on which voice client is associated currently
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

aiManagedModeSinceLastSync		1.3.6.1.4.1.14823.2.3.3.1.3.1
Time since last config was applied
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

aiTrapsGroup		1.3.6.1.4.1.14823.2.3.3.1.200
OBJECT IDENTIFIER

aiTrapObjectsGroup		1.3.6.1.4.1.14823.2.3.3.1.200.1
OBJECT IDENTIFIER

aiTrapDefinitionsGroup		1.3.6.1.4.1.14823.2.3.3.1.200.2
OBJECT IDENTIFIER

wlsxTrapAPMacAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.1
This object is used in the traps to indicate the wired MAC address of an access point, for which the trap is being raised.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapAPIpAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.2
This object is used in the traps to indicate the IP address of an access point, for which the trap is being raised.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapAPBSSID		1.3.6.1.4.1.14823.2.3.3.1.200.1.3
This object is used in the traps to indicate the BSSID of the access point, for which the trap is being raised.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapEssid		1.3.6.1.4.1.14823.2.3.3.1.200.1.4
This object is used in the traps to indicate the SSID of the access point, for which the trap is being raised.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapTargetAPBSSID		1.3.6.1.4.1.14823.2.3.3.1.200.1.5
This object is used in the traps to indicate the BSSID of the access point, for which we are raising the trap. If an Air Monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapTargetAPSSID		1.3.6.1.4.1.14823.2.3.3.1.200.1.6
This object is used in the traps to indicate the SSID of the access point, for which the trap is being raised. If an Air Monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapTargetAPChannel		1.3.6.1.4.1.14823.2.3.3.1.200.1.7
This object is used in the traps to indicate the channel of the access point, for which the trap is being raised. If an wlsxr monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapNodeMac		1.3.6.1.4.1.14823.2.3.3.1.200.1.8
This object is used in the traps to indicate the MAC address of a node.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapSourceMac		1.3.6.1.4.1.14823.2.3.3.1.200.1.9
This object is used in the traps to indicate the MAC address of the source.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxReceiverMac		1.3.6.1.4.1.14823.2.3.3.1.200.1.10
This object is used in the traps to indicate the MAC address of the receiver.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapTransmitterMac		1.3.6.1.4.1.14823.2.3.3.1.200.1.11
This object is used in the traps to indicate the MAC address of the transmitter.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapReceiverMac		1.3.6.1.4.1.14823.2.3.3.1.200.1.12
This object is used in the traps to indicate the MAC address of the receiver.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapSnr		1.3.6.1.4.1.14823.2.3.3.1.200.1.13
This object is used in the traps to indicate the Signal to Noise ratio.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapSignatureName		1.3.6.1.4.1.14823.2.3.3.1.200.1.14
This object is used in the traps to indicate the Signature Name.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapFrameType		1.3.6.1.4.1.14823.2.3.3.1.200.1.15
This object is used in the traps to indicate the Frame Type
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaFrameType

wlsxTrapAddressType		1.3.6.1.4.1.14823.2.3.3.1.200.1.16
This object is used in the traps to indicate the Address type.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaAddressType

wlsxTrapAPLocation		1.3.6.1.4.1.14823.2.3.3.1.200.1.17
This object is used in the traps to indicate the Location of the AP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapAPChannel		1.3.6.1.4.1.14823.2.3.3.1.200.1.18
This object is used in the traps to indicate the Current Channel.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapAPTxPower		1.3.6.1.4.1.14823.2.3.3.1.200.1.19
This object is used in the traps to indicate the AP Transmit Power.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapMatchedMac		1.3.6.1.4.1.14823.2.3.3.1.200.1.20
This object is used in the traps to indicate the MAC address
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapMatchedIp		1.3.6.1.4.1.14823.2.3.3.1.200.1.21
This object is used in the traps to indicate the IP address
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapRogueIfoURL		1.3.6.1.4.1.14823.2.3.3.1.200.1.22
This object is used to point to the WEBUI Rogue AP information URL.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapVlanId		1.3.6.1.4.1.14823.2.3.3.1.200.1.23
This object is used in the traps to indicate the VLAN Id.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapAdminStatus		1.3.6.1.4.1.14823.2.3.3.1.200.1.24
This object is used in the traps to indicate the admin status of VLAN.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaEnableValue

wlsxTrapOperStatus		1.3.6.1.4.1.14823.2.3.3.1.200.1.25
This object is used in the traps to indicate the admin status of VLAN.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaOperStateValue

wlsxTrapAuthServerName		1.3.6.1.4.1.14823.2.3.3.1.200.1.26
This object is used in the traps to indicate the Authentication Server used for Authentication.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapAuthServerTimeout		1.3.6.1.4.1.14823.2.3.3.1.200.1.27
This object is used in the traps to indicate the Authentication Server Timeout.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapCardSlot		1.3.6.1.4.1.14823.2.3.3.1.200.1.28
This object is used in the traps to indicate the Slot in which this card is present.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapTemperatureValue		1.3.6.1.4.1.14823.2.3.3.1.200.1.29
This object is used in the traps to indicate the Temperature Value.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapProcessName		1.3.6.1.4.1.14823.2.3.3.1.200.1.30
This object is used in the traps to indicate the Process name.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapFanNumber		1.3.6.1.4.1.14823.2.3.3.1.200.1.31
This object is used in the traps to indicate the Fan Number.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapVoltageType		1.3.6.1.4.1.14823.2.3.3.1.200.1.32
This object is used in the traps to indicate the type of Voltage.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapVoltageValue		1.3.6.1.4.1.14823.2.3.3.1.200.1.33
This object is used in the traps to indicate the voltage value in Float.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapStationBlackListReason		1.3.6.1.4.1.14823.2.3.3.1.200.1.34
The Reason for which a station is black listed.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaBlackListReason

wlsxTrapSpoofedIpAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.35
This object is used in a trap to identify a spoofed IP address.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapSpoofedOldPhyAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.36
This object is used in a trap to identify an old MAC address.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapSpoofedNewPhyAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.37
This object is used in a trap to identify a New MAC address.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapDBName		1.3.6.1.4.1.14823.2.3.3.1.200.1.38
This object is used in a trap to identify name of the database.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapDBUserName		1.3.6.1.4.1.14823.2.3.3.1.200.1.39
This object is used in a trap to identify name of the database user.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapDBIpAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.40
This object is used in a trap to identify the IpAddress of the Database.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapDBType		1.3.6.1.4.1.14823.2.3.3.1.200.1.41
This object is used in a trap to identify the port of the user.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaDBType

wlsxTrapVrrpID		1.3.6.1.4.1.14823.2.3.3.1.200.1.42
This object contains the Virtual Router Identifier.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapVrrpMasterIp		1.3.6.1.4.1.14823.2.3.3.1.200.1.43
This object contains the Master IP address.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapVrrpOperState		1.3.6.1.4.1.14823.2.3.3.1.200.1.44
This object represents the VRRP Operational state.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaVrrpState

wlsxTrapESIServerGrpName		1.3.6.1.4.1.14823.2.3.3.1.200.1.45
This object represents the External Services Interface (ESI) Server Group name
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapESIServerName		1.3.6.1.4.1.14823.2.3.3.1.200.1.46
This object represents the External Services Interface (ESI) Server Name
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapESIServerIpAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.47
This object represents the External Services Interface (ESI) Server IP address
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapLicenseDaysRemaining		1.3.6.1.4.1.14823.2.3.3.1.200.1.48
This object represents number of the days remaining prior to a license expiry.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapSwitchIp		1.3.6.1.4.1.14823.2.3.3.1.200.1.49
This object represents the controller IP address.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapSwitchRole		1.3.6.1.4.1.14823.2.3.3.1.200.1.50
This object represents the Role of the controller.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaSwitchRole

wlsxTrapUserIpAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.51
This object represents IP address of the User.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapUserPhyAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.52
This object represents MAC address of the User.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapUserName		1.3.6.1.4.1.14823.2.3.3.1.200.1.53
This object represents the user name.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapUserRole		1.3.6.1.4.1.14823.2.3.3.1.200.1.54
This object represents the Authentication method of the user.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapUserAuthenticationMethod		1.3.6.1.4.1.14823.2.3.3.1.200.1.55
This object represents the Authentication method of the user.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaAuthenticationMethods

wlsxTrapAPRadioNumber		1.3.6.1.4.1.14823.2.3.3.1.200.1.56
This object represents the radio number.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapRogueInfoURL		1.3.6.1.4.1.14823.2.3.3.1.200.1.57
This object is used to point to the WEBGUI Rogue AP information URL.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapInterferingAPInfoURL		1.3.6.1.4.1.14823.2.3.3.1.200.1.58
This object is used to point to the WEBGUI Rogue interfering AP information URL.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapPortNumber		1.3.6.1.4.1.14823.2.3.3.1.200.1.59
This object is used in the traps to indicate the port number.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapTime		1.3.6.1.4.1.14823.2.3.3.1.200.1.60
This object is used in all the enterprise traps to indicate the the time when the trap is generated on the controller.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DateAndTime

wlsxTrapHostIp		1.3.6.1.4.1.14823.2.3.3.1.200.1.61
This object represents the Trap host.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapHostPort		1.3.6.1.4.1.14823.2.3.3.1.200.1.62
This object represents the Trap host port.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapConfigurationId		1.3.6.1.4.1.14823.2.3.3.1.200.1.63
This object represents the ID of the configuration, to be used in traps.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapCTSURL		1.3.6.1.4.1.14823.2.3.3.1.200.1.64
This object represents the URL from which the transfer should happen.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapCTSTransferType		1.3.6.1.4.1.14823.2.3.3.1.200.1.65
This object represents the transfer type, upload or download.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapConfigurationState		1.3.6.1.4.1.14823.2.3.3.1.200.1.66
This object represents state of the configuration transfer.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaConfigurationState

wlsxTrapUpdateFailureReason		1.3.6.1.4.1.14823.2.3.3.1.200.1.67
This object represents the reason for the update failure.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapUpdateFailedObj		1.3.6.1.4.1.14823.2.3.3.1.200.1.68
This variable represents the AMAPI object which is the reason for the the update failure.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapTableEntryChangeType		1.3.6.1.4.1.14823.2.3.3.1.200.1.69
This object represents type of the configuration change.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaConfigurationChangeType

wlsxTrapGlobalConfigObj		1.3.6.1.4.1.14823.2.3.3.1.200.1.70
This variable represents the AMAPI object corresponding to the global configuration change.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapTableGenNumber		1.3.6.1.4.1.14823.2.3.3.1.200.1.71
This object represents generation number of a table. Used in the MMS, to keep track of the table content changes.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapLicenseId		1.3.6.1.4.1.14823.2.3.3.1.200.1.72
This object is used in the traps to indicate the license ID.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapConfidenceLevel		1.3.6.1.4.1.14823.2.3.3.1.200.1.73
This object is used in the traps to indicate the Confidence Level as a percentage
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapMissingLicenses		1.3.6.1.4.1.14823.2.3.3.1.200.1.74
This variable indicates any licenses that are not present during a configuration update
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxVoiceCurrentNumCdr		1.3.6.1.4.1.14823.2.3.3.1.200.1.75
This object represents the number of CDRs in buffer.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapTunnelId		1.3.6.1.4.1.14823.2.3.3.1.200.1.76
This Object represents the tunnel ID.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapTunnelStatus		1.3.6.1.4.1.14823.2.3.3.1.200.1.77
This Object represents the tunnel Status.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapTunnelUpReason		1.3.6.1.4.1.14823.2.3.3.1.200.1.78
This Object represents the tunnel up reason.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapTunnelDownReason		1.3.6.1.4.1.14823.2.3.3.1.200.1.79
This Object represents the tunnel down reason.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapApSerialNumber		1.3.6.1.4.1.14823.2.3.3.1.200.1.80
This object represents the AP Serial Number.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapTimeStr		1.3.6.1.4.1.14823.2.3.3.1.200.1.81
This object represents the Time in String format.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapMasterIp		1.3.6.1.4.1.14823.2.3.3.1.200.1.82
This object represents the master IP address.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapLocalIp		1.3.6.1.4.1.14823.2.3.3.1.200.1.83
This object represents the Local IP address.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapMasterName		1.3.6.1.4.1.14823.2.3.3.1.200.1.84
This object represents the master controller name.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapLocalName		1.3.6.1.4.1.14823.2.3.3.1.200.1.85
This object represents the local controller name.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapPrimaryControllerIp		1.3.6.1.4.1.14823.2.3.3.1.200.1.86
This object represents the IP address of the AP's primary controller.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapBackupControllerIp		1.3.6.1.4.1.14823.2.3.3.1.200.1.87
This object represents the IP address of the AP's backup controller.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapSpoofedFrameType		1.3.6.1.4.1.14823.2.3.3.1.200.1.88
This object is used in the traps to indicate the Spoofed Frame Type
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapAssociationType		1.3.6.1.4.1.14823.2.3.3.1.200.1.89
This object is used in the traps to indicate the type of association
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapDeviceIpAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.90
This object represents the IP address of a device seen by an AP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapDeviceMac		1.3.6.1.4.1.14823.2.3.3.1.200.1.91
This object represents the MAC address of a device seen by an AP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapVcIpAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.92
This object represents the Ip Address of a Voice client.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapVcMacAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.93
This object represents the MAC address of a Voice client.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

wlsxTrapAPName		1.3.6.1.4.1.14823.2.3.3.1.200.1.94
This object is used in the traps to indicate the Name of the AP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapApMode		1.3.6.1.4.1.14823.2.3.3.1.200.1.95
This Object represents the AP Mode.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapAPPrevChannel		1.3.6.1.4.1.14823.2.3.3.1.200.1.96
This object is used in the traps to indicate the Previous Channel.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapAPPrevChannelSec		1.3.6.1.4.1.14823.2.3.3.1.200.1.97
This object is used in the traps to indicate the Previous Secondary Channel.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaHTExtChannel

wlsxTrapAPPrevTxPower		1.3.6.1.4.1.14823.2.3.3.1.200.1.98
This object is used in the traps to indicate previous AP Transmit Power.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapAPCurMode		1.3.6.1.4.1.14823.2.3.3.1.200.1.99
This Object represents the APs Current Mode.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaAccessPointMode

wlsxTrapAPPrevMode		1.3.6.1.4.1.14823.2.3.3.1.200.1.100
This Object represents the APs Previous Mode.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaAccessPointMode

wlsxTrapAPARMChangeReason		1.3.6.1.4.1.14823.2.3.3.1.200.1.101
This Object represents the APs Previous Mode.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaARMChangeReason

wlsxTrapAPChannelSec		1.3.6.1.4.1.14823.2.3.3.1.200.1.102
This object is used in the traps to indicate the Current Secondary Channel.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaHTExtChannel

wlsxTrapUserAttributeChangeType		1.3.6.1.4.1.14823.2.3.3.1.200.1.103
This object represents type of the configuration change.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaConfigurationChangeType

wlsxTrapApControllerIp		1.3.6.1.4.1.14823.2.3.3.1.200.1.104
IP address of the controller to which the AP is (or was most recently) registered.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapApMasterStatus		1.3.6.1.4.1.14823.2.3.3.1.200.1.105
Status of the AP as seen by the master when the status changes.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaAPMasterStatus

wlsxTrapCaName		1.3.6.1.4.1.14823.2.3.3.1.200.1.106
This object is used in the traps to indicate the name of the trustpoint.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapCrlName		1.3.6.1.4.1.14823.2.3.3.1.200.1.107
This object is used in the traps to indicate the name of the crl.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapCount		1.3.6.1.4.1.14823.2.3.3.1.200.1.108
This object represents the number of occurrence of this trap.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

wlsxTrapAPPreviousUplinkType		1.3.6.1.4.1.14823.2.3.3.1.200.1.130
This object specifies the up link type for an AP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaAPUplinkType

wlsxTrapAPPreviousUplinkActiveTime		1.3.6.1.4.1.14823.2.3.3.1.200.1.131
This object specifies the up link type for an AP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TimeTicks

wlsxTrapAPActiveUplinkType		1.3.6.1.4.1.14823.2.3.3.1.200.1.132
This object specifies the up link type for an AP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaAPUplinkType

wlsxTrapAPUplinkChangeReason		1.3.6.1.4.1.14823.2.3.3.1.200.1.133
This object specifies the up link change reason.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaAPUplinkChangeReason

wlsxTrapAPManagedModeConfigFailure		1.3.6.1.4.1.14823.2.3.3.1.200.1.138
This object indicates the error for the failure of config apply on IAP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapAuthServerAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.139
This object is used in the traps to indicate the Authentication Server IP used for Authentication.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	IpAddress

wlsxTrapPortalServerName		1.3.6.1.4.1.14823.2.3.3.1.200.1.140
This object is used in the traps to indicate the Captive Portal Server used for Authentication.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapPortalServerAddress		1.3.6.1.4.1.14823.2.3.3.1.200.1.141
This object is used in the traps to indicate the Captive Portal Server IP or host name used for Authentication.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..64)

wlsxTrapPortalServerDownReason		1.3.6.1.4.1.14823.2.3.3.1.200.1.142
This object specifies the captive portal server down reason.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	ArubaPortalServerDownReason

wlsxNodeRateAnomaly		1.3.6.1.4.1.14823.2.3.3.1.200.2.1003
This trap indicates that a node is exceeding the threshold set for the frame type.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNUserEntryCreated		1.3.6.1.4.1.14823.2.3.3.1.200.2.1014
This trap indicates that a new user was created.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNUserEntryDeleted		1.3.6.1.4.1.14823.2.3.3.1.200.2.1015
This trap indicates that a user was deleted.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNUserEntryAuthenticated		1.3.6.1.4.1.14823.2.3.3.1.200.2.1016
This trap indicates that a user is Authenticated.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNUserEntryDeAuthenticated		1.3.6.1.4.1.14823.2.3.3.1.200.2.1017
This trap indicates that a user is Deauthenticated.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNUserAuthenticationFailed		1.3.6.1.4.1.14823.2.3.3.1.200.2.1018
This trap indicates that a user authentication has failed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAuthServerReqTimedOut		1.3.6.1.4.1.14823.2.3.3.1.200.2.1019
This trap indicates that the authentication server request timed out.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAuthServerTimedOut		1.3.6.1.4.1.14823.2.3.3.1.200.2.1020
This trap indicates that the authentication server timed out.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAuthServerIsUp		1.3.6.1.4.1.14823.2.3.3.1.200.2.1021
This trap indicates that an authentication server is up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAccessPointIsUp		1.3.6.1.4.1.14823.2.3.3.1.200.2.1040
A Trap which indicates that an access point up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAccessPointIsDown		1.3.6.1.4.1.14823.2.3.3.1.200.2.1041
A Trap which indicates that an access point down.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNChannelChanged		1.3.6.1.4.1.14823.2.3.3.1.200.2.1043
This trap indicates that an access point at Location wlsxTrapAPLocation has changed the channel.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNStationAddedToBlackList		1.3.6.1.4.1.14823.2.3.3.1.200.2.1044
This trap indicates that the station is black listed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNStationRemovedFromBlackList		1.3.6.1.4.1.14823.2.3.3.1.200.2.1045
This trap indicates that the station is removed from the black list.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNRadioAttributesChanged		1.3.6.1.4.1.14823.2.3.3.1.200.2.1049
A Trap which indicates changes in the Radio attributes of an access point.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxUnsecureAPDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1053
This trap indicates that an unauthorized access point is connected to the wired network. The access point is declared Rogue because it was matched to a MAC address.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxUnsecureAPResolved		1.3.6.1.4.1.14823.2.3.3.1.200.2.1054
This trap indicates that a previously detected access point, classified as Rogue, is no longer present in the network.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxStaImpersonation		1.3.6.1.4.1.14823.2.3.3.1.200.2.1055
This trap indicates that an AM detected Station Impersonation.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxReservedChannelViolation		1.3.6.1.4.1.14823.2.3.3.1.200.2.1056
This trap indicates that an AM detected an access point which is violating the Reserved Channel configuration.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxValidSSIDViolation		1.3.6.1.4.1.14823.2.3.3.1.200.2.1057
This trap indicates that an AP has detected an access point is violating Valid SSID configuration by using an SSID that is reserved for use by a valid AP only.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxChannelMisconfiguration		1.3.6.1.4.1.14823.2.3.3.1.200.2.1058
This trap indicates that an AP detected an access point that has a channel misconfiguration because it is using a channel that is not valid.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxOUIMisconfiguration		1.3.6.1.4.1.14823.2.3.3.1.200.2.1059
This trap indicates that an AP detected an access point that has an OUI misconfiguration because it is using an OUI that is not valid.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSSIDMisconfiguration		1.3.6.1.4.1.14823.2.3.3.1.200.2.1060
This trap indicates that an AP detected an access point that has an SSID misconfiguration because it is using an SSID that is not valid.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxShortPreableMisconfiguration		1.3.6.1.4.1.14823.2.3.3.1.200.2.1061
This trap indicates that an access point has bad Short preamble configuration.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxWPAMisconfiguration		1.3.6.1.4.1.14823.2.3.3.1.200.2.1062
This trap indicates that an AP detected an access point that is misconfigured because it is not using WPA.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAdhocNetworkDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1063
This trap indicates that an AM has detected an Ad hoc network.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAdhocNetworkRemoved		1.3.6.1.4.1.14823.2.3.3.1.200.2.1064
This trap indicates that a previously detected Ad hoc Network is no longer present in the network.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxStaPolicyViolation		1.3.6.1.4.1.14823.2.3.3.1.200.2.1065
This trap indicates that Protection was enforced because a valid station's association to a non-valid access point violated Valid Station policy. For more info check: http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0019
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxRepeatWEPIVViolation		1.3.6.1.4.1.14823.2.3.3.1.200.2.1066
This trap indicates that an AP detected that a valid access point is using the same WEP initialization vector in consecutive packets.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxWeakWEPIVViolation		1.3.6.1.4.1.14823.2.3.3.1.200.2.1067
This trap indicates that an AP detected that a valid access point is using a Weak WEP initialization vector. For more info check: http://www.wve.org/entries/show/WVE-2005-0021
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxChannelInterferenceDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1068
This trap indicates that an AP has detected channel interference.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxChannelInterferenceCleared		1.3.6.1.4.1.14823.2.3.3.1.200.2.1069
This trap indicates that a previously detected channel interference is no longer present.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPInterferenceDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1070
This trap indicates that an AP has detected interference for an access point.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPInterferenceCleared		1.3.6.1.4.1.14823.2.3.3.1.200.2.1071
This trap indicates that the previously detected interference for an access point is no longer present.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxStaInterferenceDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1072
This trap indicates that an AP has detected interference for a station.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxStaInterferenceCleared		1.3.6.1.4.1.14823.2.3.3.1.200.2.1073
This trap indicates that the previously detected interference for a station is no longer present.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxFrameRetryRateExceeded		1.3.6.1.4.1.14823.2.3.3.1.200.2.1074
This trap indicates that an AP detected that an access point has exceeded the configured upper threshold for Frame Retry Rate.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxFrameReceiveErrorRateExceeded		1.3.6.1.4.1.14823.2.3.3.1.200.2.1075
This trap indicates that an AP detected that an access point has exceeded the configured upper threshold for Frame Receive Error Rate.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxFrameFragmentationRateExceeded		1.3.6.1.4.1.14823.2.3.3.1.200.2.1076
This trap indicates that an AP detected that an access point exceeded the configured upper threshold for Frame Fragmentation Rate.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxFrameBandWidthRateExceeded		1.3.6.1.4.1.14823.2.3.3.1.200.2.1077
This trap indicates that an AP detected that a station or access point has exceeded the configured upper threshold for Bandwidth rate.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxFrameLowSpeedRateExceeded		1.3.6.1.4.1.14823.2.3.3.1.200.2.1078
This trap indicates that an AP detected that a station has exceeded the configured upper threshold for Low speed rate.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxFrameNonUnicastRateExceeded		1.3.6.1.4.1.14823.2.3.3.1.200.2.1079
This trap indicates that an AP detected that a station has exceeded the configured upper threshold for Non Unicast traffic rate.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxLoadbalancingEnabled		1.3.6.1.4.1.14823.2.3.3.1.200.2.1080
This trap indicates that an AM is reporting that an AP has enabled Load balancing.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxLoadbalancingDisabled		1.3.6.1.4.1.14823.2.3.3.1.200.2.1081
This trap indicates that an AM is reporting that an AP has enabled Load balancing.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxChannelFrameRetryRateExceeded		1.3.6.1.4.1.14823.2.3.3.1.200.2.1082
This trap indicates that an AP has detected that the configured upper threshold for Frame Retry Rate was exceeded on a channel.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxChannelFrameFragmentationRateExceeded		1.3.6.1.4.1.14823.2.3.3.1.200.2.1083
This trap indicates that an AP has detected that the configured upper threshold for Frame Fragmentation Rate was exceeded on a channel.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxChannelFrameErrorRateExceeded		1.3.6.1.4.1.14823.2.3.3.1.200.2.1084
This trap indicates that an AP has detected that the configured upper threshold for Frame Receive Error Rate was exceeded on a channel.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignatureMatchAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1085
This trap indicates that an AP detected a signature match in a frame from an access point.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignatureMatchSta		1.3.6.1.4.1.14823.2.3.3.1.200.2.1086
This trap indicates that an AP detected a signature match in a frame from a Station.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxChannelRateAnomaly		1.3.6.1.4.1.14823.2.3.3.1.200.2.1087
This trap indicates that an AP detected frames on a channel which exceed the configured IDS rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0052 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNodeRateAnomalyAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1088
This trap indicates that an AP detected frames transmitted or received by an access point, which exceed the configured IDS rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0052 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNodeRateAnomalySta		1.3.6.1.4.1.14823.2.3.3.1.200.2.1089
This trap indicates that an AP detected frames transmitted or received by a node, which exceed the configured IDS rate threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxEAPRateAnomaly		1.3.6.1.4.1.14823.2.3.3.1.200.2.1090
This trap indicates that the rate of EAP Handshake packets received by an AP has exceeded the configured IDS EAP Handshake rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0049
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignalAnomaly		1.3.6.1.4.1.14823.2.3.3.1.200.2.1091
This trap indicates that an AM detected a Signal Anomaly.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSequenceNumberAnomalyAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1092
This trap indicates that an AM received packets from an AP which exceeds the acceptable sequence number difference. The acceptable sequence number difference is an IDS configuration object. For more info check: http://www.wve.org/entries/show/WVE-2005-0061 http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSequenceNumberAnomalySta		1.3.6.1.4.1.14823.2.3.3.1.200.2.1093
This trap indicates that an AM received packets from a Node which exceeds the acceptable sequence number difference. The acceptable sequence number difference is an IDS configuration object. For more info check: http://www.wve.org/entries/show/WVE-2005-0061 http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxDisconnectStationAttack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1094
This trap indicates that an AM detected a station Disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxApFloodAttack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1095
This trap indicates that the number of potential fake APs detected by an AP has exceeded the configured IDS threshold. This is the total number of fake APs observed across all bands. For more info check: http://www.wve.org/entries/show/WVE-2005-0056
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAdhocNetwork		1.3.6.1.4.1.14823.2.3.3.1.200.2.1096
This trap indicates that an AM detected an Ad hoc Network. An Station is connected to an ad hoc AP.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxWirelessBridge		1.3.6.1.4.1.14823.2.3.3.1.200.2.1097
This trap indicates that an AP detected a Wireless Bridge when a WDS frame was seen between the transmitter and receiver addresses.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxInvalidMacOUIAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1098
This trap indicates that an AP detected an invalid MAC OUI in the BSSID of a frame. An invalid MAC OUI suggests that the frame may be spoofed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxInvalidMacOUISta		1.3.6.1.4.1.14823.2.3.3.1.200.2.1099
This trap indicates that an AP detected an invalid MAC OUI in the SRC or DST address of a frame. An invalid MAC OUI suggests that the frame may be spoofed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxWEPMisconfiguration		1.3.6.1.4.1.14823.2.3.3.1.200.2.1100
This trap indicates that an AP detected an access point that is misconfigured because it does not have Privacy enabled.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxStaRepeatWEPIVViolation		1.3.6.1.4.1.14823.2.3.3.1.200.2.1101
This trap indicates that an AP detected that a valid station is using the same WEP initialization vector in consecutive packets.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxStaWeakWEPIVViolation		1.3.6.1.4.1.14823.2.3.3.1.200.2.1102
This trap indicates that an AP detected that a valid station is using a Weak WEP initialization vector.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxStaAssociatedToUnsecureAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1103
This trap indicates that an AM detected a client associated with a Rogue access point.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxStaUnAssociatedFromUnsecureAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1104
This trap indicates that a previously detected rogue access point association is no longer present.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAdhocNetworkBridgeDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1105
This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxInterferingApDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1106
This trap indicates that an AP detected an access point classified as Interfering. The access point is declared Interfering because it is neither authorized or classified as Rogue.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxColdStart		1.3.6.1.4.1.14823.2.3.3.1.200.2.1111
An enterprise version of cold start trap, which contains the controller time stamp.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxWarmStart		1.3.6.1.4.1.14823.2.3.3.1.200.2.1112
An enterprise version of warm start trap, which contains the controller time stamp.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPImpersonation		1.3.6.1.4.1.14823.2.3.3.1.200.2.1113
This trap indicates that an AP detected AP Impersonation because the number of beacons seen has exceeded the expected number by the configured percentage threshold. The expected number is calculated based on the Beacon Interval Field in the Beacon frame.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAuthServerIsDown		1.3.6.1.4.1.14823.2.3.3.1.200.2.1115
This trap indicates that an authentication server is down.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxWindowsBridgeDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1129
This trap indicates that an AM has detected a station that is bridging from a wireless network to a wired network
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignAPNetstumbler		1.3.6.1.4.1.14823.2.3.3.1.200.2.1134
This trap indicates that an AP detected a signature match for Netstumbler from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0025
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignStaNetstumbler		1.3.6.1.4.1.14823.2.3.3.1.200.2.1135
This trap indicates that an AP detected a signature match for Netstumbler from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0025
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignAPAsleap		1.3.6.1.4.1.14823.2.3.3.1.200.2.1136
This trap indicates that an AP detected a signature match for ASLEAP from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0027
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignStaAsleap		1.3.6.1.4.1.14823.2.3.3.1.200.2.1137
This trap indicates that an AP detected a signature match for ASLEAP from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0027
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignAPAirjack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1138
This trap indicates that an AP detected a signature match for AirJack from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0018
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignStaAirjack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1139
This trap indicates that an AP detected a signature match for AirJack from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0018
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignAPNullProbeResp		1.3.6.1.4.1.14823.2.3.3.1.200.2.1140
This trap indicates that an AP detected a signature match for Null-Probe-Response from an access point. For more info check: http://www.wve.org/entries/show/WVE-2006-0064
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignStaNullProbeResp		1.3.6.1.4.1.14823.2.3.3.1.200.2.1141
This trap indicates that an AP detected a signature match for Null-Probe-Response from a Station. For more info check: http://www.wve.org/entries/show/WVE-2006-0064
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignAPDeauthBcast		1.3.6.1.4.1.14823.2.3.3.1.200.2.1142
This trap indicates that an AP detected a signature match for Deauth-Broadcast from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSignStaDeauthBcast		1.3.6.1.4.1.14823.2.3.3.1.200.2.1143
This trap indicates that an AP detected a signature match for Deauth-Broadcast from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxWindowsBridgeDetectedAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1144
This trap indicates that an AP is detecting an access point that is bridging from a wireless network to a wired network.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxWindowsBridgeDetectedSta		1.3.6.1.4.1.14823.2.3.3.1.200.2.1145
This trap indicates that an AP is detecting a station that is bridging from a wireless network to a wired network.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAdhocNetworkBridgeDetectedAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1146
This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAdhocNetworkBridgeDetectedSta		1.3.6.1.4.1.14823.2.3.3.1.200.2.1147
This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxDisconnectStationAttackAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1148
This trap indicates that an AM detected a station disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxDisconnectStationAttackSta		1.3.6.1.4.1.14823.2.3.3.1.200.2.1149
This trap indicates that an AM detected a station Disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSuspectUnsecureAPDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1150
This trap indicates that an access point, classified as Suspected Rogue, has been detected by a Controller. The AP is suspected to be rogue, with the supplied confidence level, because it was matched to the wired MAC address.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxSuspectUnsecureAPResolved		1.3.6.1.4.1.14823.2.3.3.1.200.2.1151
This trap indicates that a previously detected access point, classified Suspected Rogue, is either no longer present in the network or has changed its state.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxHtGreenfieldSupported		1.3.6.1.4.1.14823.2.3.3.1.200.2.1157
This trap indicates that an AP detected an access point that supports HT Greenfield mode. For more info check: http://www.wve.org/entries/show/WVE-2008-0005
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxHT40MHzIntoleranceAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1158
This trap indicates that an AP is detecting an access point with the HT 40MHz intolerance setting. For more info check: http://www.wve.org/entries/show/WVE-2008-0004
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxHT40MHzIntoleranceSta		1.3.6.1.4.1.14823.2.3.3.1.200.2.1159
This trap indicates that the system is detecting an HT 40MHz Intolerance setting from a Station. For more info check: http://www.wve.org/entries/show/WVE-2008-0004
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAuthServerAllInService		1.3.6.1.4.1.14823.2.3.3.1.200.2.1160
This trap indicates that all authentication servers is a server group are brought back in service.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAdhocNetwork		1.3.6.1.4.1.14823.2.3.3.1.200.2.1161
This trap indicates that an AP detected an ad hoc network where a station is connected to an ad hoc access point.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAdhocNetworkBridgeDetectedAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1162
This trap indicates that an AP detected an ad hoc network that is bridging to a wired network.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAdhocNetworkBridgeDetectedSta		1.3.6.1.4.1.14823.2.3.3.1.200.2.1163
This trap indicates that an AP detected an ad hoc network that is bridging to a wired network.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxClientFloodAttack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1170
This trap indicates that the number of potential fake clients detected by an AP has exceeded the configured IDS threshold. This is the total number of fake clients observed across all bands. For more info check: http://www.wve.org/entries/show/WVE-2005-0056
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxValidClientNotUsingEncryption		1.3.6.1.4.1.14823.2.3.3.1.200.2.1171
This trap indicates that an AP detected an unencrypted data frame between a valid client and an access point.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAdhocUsingValidSSID		1.3.6.1.4.1.14823.2.3.3.1.200.2.1172
This trap indicates that an AP detected an ad hoc network using a valid/protected SSID. For more info check: http://www.wve.org/entries/show/WVE-2005-0008
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPSpoofingDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1173
This trap indicates that an AP detected that one of its virtual APs is being spoofed using MAC spoofing. For more info check: http://www.wve.org/entries/show/WVE-2005-0019
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxClientAssociatingOnWrongChannel		1.3.6.1.4.1.14823.2.3.3.1.200.2.1174
This trap indicates that an AP detected a client trying to associate to one of its BSSIDs on the wrong channel. This can be a sign that the BSSID is being spoofed in order to fool the client into thinking the AP is operating on another channel.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNDisconnectStationAttack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1175
This trap indicates that an AP has determined that a client is under Disconnect Attack because the rate of Assoc/Reassoc Response packets received by that client exceeds the configured threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNStaUnAssociatedFromUnsecureAP		1.3.6.1.4.1.14823.2.3.3.1.200.2.1176
This trap indicates that an AP that had previously detected a client association to a Rogue access point is no longer detecting that association.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxOmertaAttack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1177
This trap indicates that an AP detected an Omerta attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0053
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxTKIPReplayAttack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1178
This trap indicates that an AP detected a TKIP replay attack. If successful this could be the precursor to more advanced attacks. For more info check: http://www.wve.org/entries/show/WVE-2008-0013
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxChopChopAttack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1179
This trap indicates that an AP detected a ChopChop attack. For more info check: http://www.wve.org/entries/show/WVE-2006-0038
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxFataJackAttack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1180
This trap indicates that an AP detected a FATA-Jack attack. For more info check: http://www.wve.org/entries/show/WVE-2006-0057
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxInvalidAddressCombination		1.3.6.1.4.1.14823.2.3.3.1.200.2.1181
This trap indicates that an AP detected an invalid source and destination combination. For more info check: http://www.wve.org/entries/show/WVE-2008-0011
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxValidClientMisassociation		1.3.6.1.4.1.14823.2.3.3.1.200.2.1182
This trap indicates that an AP detected a misassociation between a valid client and an unsafe AP.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxMalformedHTIEDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1183
This trap indicates that an AP detected a malformed HT Information Element. This can be the result of a misbehaving wireless driver or it may be an indication of a new wireless attack.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxMalformedAssocReqDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1184
This trap indicates that an AP detected a malformed association request with a NULL SSID. For more info check: http://www.wve.org/entries/show/WVE-2008-0010
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxOverflowIEDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1185
This trap indicates that an AP detected a management frame with a malformed information element. The declared length of the element is larger than the entire frame containing the element. This may be used to corrupt or crash wireless drivers. For more info check: http://www.wve.org/entries/show/WVE-2008-0008
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxOverflowEAPOLKeyDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1186
This trap indicates that an AP detected a key in an EAPOL Key message with a specified length greater than the length of the entire message. For more info check: http://www.wve.org/entries/show/WVE-2008-0009
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxMalformedFrameLargeDurationDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1187
This trap indicates that an AP detected an unusually large duration in a wireless frame. This may be an attempt to block other devices from transmitting. For more info check: http://www.wve.org/entries/show/WVE-2005-0051
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxMalformedFrameWrongChannelDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1188
This trap indicates that an AP detected a beacon on one channel advertising another channel. This could be an attempt to lure clients away from a valid AP. For more info check: http://www.wve.org/entries/show/WVE-2006-0050
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxMalformedAuthFrame		1.3.6.1.4.1.14823.2.3.3.1.200.2.1189
This trap indicates that an AP detected an authentication frame with either a bad algorithm (similar to Fata-Jack) or a bad transaction. For more info check: http://www.wve.org/entries/show/WVE-2006-0057
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxCTSRateAnomaly		1.3.6.1.4.1.14823.2.3.3.1.200.2.1190
This trap indicates that the rate of CTS packets received by an AP exceeds the configured IDS threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxRTSRateAnomaly		1.3.6.1.4.1.14823.2.3.3.1.200.2.1191
This trap indicates that the rate of RTS packets received by an AP exceeds the configured IDS threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNRogueAPDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1192
This trap indicates that an unauthorized access point is connected to the wired network. The access point is classified as Rogue by the system.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNRogueAPResolved		1.3.6.1.4.1.14823.2.3.3.1.200.2.1193
This trap indicates that a previously detected access point, classified as Rogue, is either no longer present in the network or it changed its state.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNeighborAPDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1194
This trap indicates that an access point has been classified as a Neighbor by the system.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNInterferingAPDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1195
This trap indicates that an access point has been classified as Interfering by the system. The access point is declared Interfering because it is not authorized, nor has it been classified as a Rogue.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNSuspectRogueAPDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1196
This trap indicates that an access point, classified as Suspected Rogue, is detected by the system. The AP is suspected to be rogue with the supplied confidence level.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNSuspectRogueAPResolved		1.3.6.1.4.1.14823.2.3.3.1.200.2.1197
This trap indicates that a previously detected access point, classified as Suspected Rogue, is either no longer present in the network or has changed its state.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxBlockAckAttackDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1198
This trap indicates that an attempt has been made to deny service to the source address by spoofing a block ACK add request that sets a sequence number window outside the currently used window. For more info check: http://www.wve.org/entries/show/WVE-2008-0006
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxHotspotterAttackDetected		1.3.6.1.4.1.14823.2.3.3.1.200.2.1199
This trap indicates that a new AP has appeared immediately following a client probe request. This is indicative of the Hotspotter tool or similar that attempts to trap clients with a fake hotspot or other wireless network. For more info check: http://www.wve.org/entries/show/WVE-2005-0054
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNSignatureMatch		1.3.6.1.4.1.14823.2.3.3.1.200.2.1200
This trap indicates that an AP detected a signature match in a frame.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNSignatureMatchNetstumbler		1.3.6.1.4.1.14823.2.3.3.1.200.2.1201
This trap indicates that an AP detected a signature match for Netstumbler in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0025
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNSignatureMatchAsleap		1.3.6.1.4.1.14823.2.3.3.1.200.2.1202
This trap indicates that an AP detected a signature match for ASLEAP in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0027
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNSignatureMatchAirjack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1203
This trap indicates that an AP detected a signature match for Airjack in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0018
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNSignatureMatchNullProbeResp		1.3.6.1.4.1.14823.2.3.3.1.200.2.1204
This trap indicates that an AP detected a signature match for Null-Probe-Response in a frame. For more info check: http://www.wve.org/entries/show/WVE-2006-0064
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNSignatureMatchDeauthBcast		1.3.6.1.4.1.14823.2.3.3.1.200.2.1205
This trap indicates that an AP detected a signature match for Deauth-Broadcast in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNSignatureMatchDisassocBcast		1.3.6.1.4.1.14823.2.3.3.1.200.2.1206
This trap indicates that an AP detected a signature match for Disassoc-Broadcast in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0046
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNSignatureMatchWellenreiter		1.3.6.1.4.1.14823.2.3.3.1.200.2.1207
This trap indicates that an AP detected a signature match for Wellenreiter in a frame. For more info check: http://www.wve.org/entries/show/WVE-2006-0058
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPDeauthContainment		1.3.6.1.4.1.14823.2.3.3.1.200.2.1208
This trap indicates that an AP has attempted to contain an access point by disconnecting its client.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxClientDeauthContainment		1.3.6.1.4.1.14823.2.3.3.1.200.2.1209
This trap indicates that an AP has attempted to contain a client by disconnecting it from the AP that it is associated with.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPWiredContainment		1.3.6.1.4.1.14823.2.3.3.1.200.2.1210
This trap indicates that an AP has attempted to contain an access point by disrupting traffic to its client on the wired interface.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxClientWiredContainment		1.3.6.1.4.1.14823.2.3.3.1.200.2.1211
This trap indicates that an AP has attempted to contain a client by disrupting traffic to it on the wired interface.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPTaggedWiredContainment		1.3.6.1.4.1.14823.2.3.3.1.200.2.1212
This trap indicates that an AP has attempted to contain an access point by disrupting traffic to its client on the wired interface.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxClientTaggedWiredContainment		1.3.6.1.4.1.14823.2.3.3.1.200.2.1213
This trap indicates that an AP has attempted to contain a client by disrupting traffic to it on the wired interface.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxTarpitContainment		1.3.6.1.4.1.14823.2.3.3.1.200.2.1214
This trap indicates that an AP has attempted to contain an access point by moving a client that is attempting to associate to it to a tarpit.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPChannelChange		1.3.6.1.4.1.14823.2.3.3.1.200.2.1216
This trap indicates that an AP changed its channel.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPPowerChange		1.3.6.1.4.1.14823.2.3.3.1.200.2.1217
This trap indicates that an AP changed its transmit power level.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPModeChange		1.3.6.1.4.1.14823.2.3.3.1.200.2.1218
This trap indicates that an AP changed its mode from AP to APMonitor or vice versa.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxUserEntryAttributesChanged		1.3.6.1.4.1.14823.2.3.3.1.200.2.1219
This trap indicates that the user entry attributes have changed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxPowerSaveDosAttack		1.3.6.1.4.1.14823.2.3.3.1.200.2.1220
This trap indicates that an AP detected a Power Save DoS attack.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAPMasterStatusChange		1.3.6.1.4.1.14823.2.3.3.1.200.2.1221
This trap indicates that the status of the AP as seen by the master controller has changed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAdhocUsingValidSSID		1.3.6.1.4.1.14823.2.3.3.1.200.2.1222
This trap indicates that an AP detected an ad hoc network node using a valid/protected SSID. For more info check: http://www.wve.org/entries/show/WVE-2005-0008
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxMgmtUserAuthenticationFailed		1.3.6.1.4.1.14823.2.3.3.1.200.2.1224
This trap indicates that a management user authentication has failed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPActiveUplinkChanged		1.3.6.1.4.1.14823.2.3.3.1.200.2.1252
When the active uplink of an AP changes, a notification is sent to the Management Entity with the new uplink type
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxAPManagedModeConfigFailureTrap		1.3.6.1.4.1.14823.2.3.3.1.200.2.1255
Indicated failure in applying config.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxNAuthServerAcctTimedOut		1.3.6.1.4.1.14823.2.3.3.1.200.2.1256
This trap indicates that the authentication server accounting timed out.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxPortalServerDown		1.3.6.1.4.1.14823.2.3.3.1.200.2.1259
This trap indicates that the portal server is down.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxPortalServerUp		1.3.6.1.4.1.14823.2.3.3.1.200.2.1260
This trap indicates that the portal server is up.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

wlsxIAPVoiceClientLocationUpdate		1.3.6.1.4.1.14823.2.3.3.1.200.2.1262
The trap represents a IAP voice client location update.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE