AIRESPACE-WIRELESS-MIB

File: AIRESPACE-WIRELESS-MIB.mib (640433 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
AIRESPACE-REF-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Integer32 Counter32 Unsigned32
Counter64 Gauge32 IpAddress
TimeTicks NOTIFICATION-GROUP OBJECT-GROUP
MODULE-COMPLIANCE TEXTUAL-CONVENTION DisplayString
RowStatus MacAddress TruthValue
TimeInterval airespace

Defined Types

WEPKeytype  
This object indicates the WEP Key type.
TEXTUAL-CONVENTION    
  OCTET STRING Size(4..32)  

ProfileState  
This object indicates the profile state.
TEXTUAL-CONVENTION    
  INTEGER fail(0), pass(1)  

BsnTxtSignatureMacInfo  
This textual convention defines the pattern followed by the LWAPP APs to perform signature analysis with the signature and report the results to the Controller. The semantics are described as follows. bsnSignatureMacAll - The Controller would set the 'Mac Info' parameter of the 'Signature Add LWAPP Message' to this value to indicate the LWAPP AP that the signature analysis and pattern matching should be tracked and reported on a per-signature and per-channel basis. bsnSignatureMacIndividual - The Controller would set the 'Mac Info' parameter of the 'Signature Add LWAPP Message' to this value to indicate the LWAPP AP that the signature analysis and pattern matching should be tracked and reported separately for individual MAC addresses, that are the sources of the received 802.11 data and/or management frames. bsnStandardSigMacBoth - The Controller would set the 'Mac Info' parameter of the 'Signature Add LWAPP Message' to this value to indicate the LWAPP AP that the signature analysis and pattern matching should be tracked on a per signature as well as per-MAC address basis.
TEXTUAL-CONVENTION    
  INTEGER bsnSignatureMacAll(0), bsnSignatureMacIndividual(1), bsnSignatureMacBoth(2)  

BsnSignaturePatternOffSetStart  
This object indicates how an offset should be applied while doing signature analysis for QOS and non-QOS data frames. This is introduced since 802.11e QOS frames have an additional 2-byte QOS header which results in the current implementation not being able to find the start of the date frames for signature analysis. The semantics of the values are as follows. sigPattStartFrm - This indicates that the required offset should be applied to the start of the data frame, before performing pattern matching of the signature on the data frame. sigPattStartFrmBody - This value indicates that the required offset should be applied to the start of the frame body, after the header, before performing pattern matching of the signature on the data frame.
TEXTUAL-CONVENTION    
  INTEGER sigPattStartFrm(0), sigPattStartFrmBody(1)  

BsnDot11EssEntry  
SEQUENCE    
  bsnDot11EssIndex Unsigned32
  bsnDot11EssSsid DisplayString
  bsnDot11EssSessionTimeout Unsigned32
  bsnDot11EssMacFiltering INTEGER
  bsnDot11EssAdminStatus INTEGER
  bsnDot11EssSecurityAuthType INTEGER
  bsnDot11EssStaticWEPSecurity INTEGER
  bsnDot11EssStaticWEPEncryptionType INTEGER
  bsnDot11EssStaticWEPDefaultKey WEPKeytype
  bsnDot11EssStaticWEPKeyIndex INTEGER
  bsnDot11EssStaticWEPKeyFormat INTEGER
  bsnDot11Ess8021xSecurity INTEGER
  bsnDot11Ess8021xEncryptionType INTEGER
  bsnDot11EssWPASecurity INTEGER
  bsnDot11EssWPAEncryptionType INTEGER
  bsnDot11EssIpsecSecurity INTEGER
  bsnDot11EssVpnEncrTransform INTEGER
  bsnDot11EssVpnAuthTransform INTEGER
  bsnDot11EssVpnIkeAuthMode INTEGER
  bsnDot11EssVpnSharedKey OCTET STRING
  bsnDot11EssVpnSharedKeySize Unsigned32
  bsnDot11EssVpnIkePhase1Mode INTEGER
  bsnDot11EssVpnIkeLifetime Integer32
  bsnDot11EssVpnIkeDHGroup INTEGER
  bsnDot11EssIpsecPassthruSecurity INTEGER
  bsnDot11EssVpnPassthruGateway IpAddress
  bsnDot11EssWebSecurity INTEGER
  bsnDot11EssRadioPolicy INTEGER
  bsnDot11EssQualityOfService INTEGER
  bsnDot11EssDhcpRequired INTEGER
  bsnDot11EssDhcpServerIpAddress IpAddress
  bsnDot11EssVpnContivityMode INTEGER
  bsnDot11EssVpnQotdServerAddress IpAddress
  bsnDot11EssBlacklistTimeout Integer32
  bsnDot11EssNumberOfMobileStations Counter32
  bsnDot11EssWebPassthru INTEGER
  bsnDot11EssCraniteSecurity INTEGER
  bsnDot11EssBlacklistingCapability INTEGER
  bsnDot11EssInterfaceName DisplayString
  bsnDot11EssAclName DisplayString
  bsnDot11EssAAAOverride INTEGER
  bsnDot11EssWPAAuthKeyMgmtMode INTEGER
  bsnDot11EssWPAAuthPresharedKey OCTET STRING
  bsnDot11EssWepAllowSharedKeyAuth INTEGER
  bsnDot11EssFortressSecurity INTEGER
  bsnDot11EssL2tpSecurity INTEGER
  bsnDot11EssWPAAuthPresharedKeyHex OCTET STRING
  bsnDot11EssBroadcastSsid INTEGER
  bsnDot11EssExternalPolicyValidation INTEGER
  bsnDot11EssRSNSecurity INTEGER
  bsnDot11EssRSNWPACompatibilityMode INTEGER
  bsnDot11EssRSNAllowTKIPClients INTEGER
  bsnDot11EssRSNAuthKeyMgmtMode INTEGER
  bsnDot11EssRSNAuthPresharedKey OCTET STRING
  bsnDot11EssRSNAuthPresharedKeyHex OCTET STRING
  bsnDot11EssIPv6Bridging INTEGER
  bsnDot11EssRowStatus RowStatus
  bsnDot11EssWmePolicySetting INTEGER
  bsnDot11Ess80211ePolicySetting INTEGER
  bsnDot11EssWebPassthroughEmail INTEGER
  bsnDot11Ess7920PhoneSupport INTEGER
  bsnDot11EssRadiusAuthPrimaryServer DisplayString
  bsnDot11EssRadiusAuthSecondaryServer DisplayString
  bsnDot11EssRadiusAuthTertiaryServer DisplayString
  bsnDot11EssRadiusAcctPrimaryServer DisplayString
  bsnDot11EssRadiusAcctSecondaryServer DisplayString
  bsnDot11EssRadiusAcctTertiaryServer DisplayString

BsnDot11QosProfileEntry  
SEQUENCE    
  bsnDot11QosProfileName OCTET STRING
  bsnDot11QosProfileDesc OCTET STRING
  bsnDot11QosAverageDataRate INTEGER
  bsnDot11QosBurstDataRate INTEGER
  bsnDot11QosAvgRealTimeDataRate INTEGER
  bsnDot11QosBurstRealTimeDataRate INTEGER
  bsnDot11QosMaxRFUsagePerAP INTEGER
  bsnDot11QosProfileQueueDepth INTEGER
  bsnDot11WiredQosProtocol INTEGER
  bsnDot11802Dot1PTag INTEGER
  bsnDot11ResetProfileToDefault INTEGER

BsnMobileStationEntry  
SEQUENCE    
  bsnMobileStationMacAddress MacAddress
  bsnMobileStationIpAddress IpAddress
  bsnMobileStationUserName DisplayString
  bsnMobileStationAPMacAddr MacAddress
  bsnMobileStationAPIfSlotId INTEGER
  bsnMobileStationEssIndex INTEGER
  bsnMobileStationSsid DisplayString
  bsnMobileStationAID Unsigned32
  bsnMobileStationStatus INTEGER
  bsnMobileStationReasonCode INTEGER
  bsnMobileStationMobilityStatus INTEGER
  bsnMobileStationAnchorAddress IpAddress
  bsnMobileStationCFPollable INTEGER
  bsnMobileStationCFPollRequest INTEGER
  bsnMobileStationChannelAgilityEnabled INTEGER
  bsnMobileStationPBCCOptionImplemented INTEGER
  bsnMobileStationShortPreambleOptionImplemented INTEGER
  bsnMobileStationSessionTimeout Unsigned32
  bsnMobileStationAuthenticationAlgorithm INTEGER
  bsnMobileStationWepState INTEGER
  bsnMobileStationPortNumber Unsigned32
  bsnMobileStationDeleteAction INTEGER
  bsnMobileStationPolicyManagerState DisplayString
  bsnMobileStationSecurityPolicyStatus INTEGER
  bsnMobileStationProtocol INTEGER
  bsnMobileStationMirrorMode INTEGER
  bsnMobileStationInterface DisplayString
  bsnMobileStationApMode INTEGER
  bsnMobileStationVlanId Integer32
  bsnMobileStationPolicyType INTEGER
  bsnMobileStationEncryptionCypher INTEGER
  bsnMobileStationEapType INTEGER
  bsnMobileStationCcxVersion INTEGER
  bsnMobileStationE2eVersion INTEGER
  bsnMobileStationStatusCode INTEGER

BsnMobileStationByIpEntry  
SEQUENCE    
  bsnMobileStationByIpAddress IpAddress
  bsnMobileStationByIpMacAddress MacAddress

BsnMobileStationByUsernameEntry  
SEQUENCE    
  bsnMobileStationByUserName OCTET STRING
  bsnMobileStationByUserMacAddress MacAddress

BsnMobileStationPerRadioPerVapEntry  
SEQUENCE    
  bsnMobileStationPerRadioPerVapIndex Integer32
  bsnMobileStationMacAddr MacAddress

BsnMobileStationStatsEntry  
SEQUENCE    
  bsnMobileStationRSSI Integer32
  bsnMobileStationBytesReceived Counter64
  bsnMobileStationBytesSent Counter64
  bsnMobileStationPolicyErrors Counter64
  bsnMobileStationPacketsReceived Counter64
  bsnMobileStationPacketsSent Counter64
  bsnMobileStationSnr Integer32

BsnMobileStationExtStatsEntry  
SEQUENCE    
  bsnMobileStationSampleTime Integer32
  bsnMobileStationTxExcessiveRetries Counter64
  bsnMobileStationTxRetries Counter64
  bsnMobileStationTxFiltered Counter64

BsnMobileStationRssiDataEntry  
SEQUENCE    
  bsnMobileStationRssiDataApMacAddress MacAddress
  bsnMobileStationRssiDataApIfSlotId Unsigned32
  bsnMobileStationRssiDataApIfType INTEGER
  bsnMobileStationRssiDataApName DisplayString
  bsnMobileStationRssiData Integer32
  bsnAPIfPhyAntennaIndex Unsigned32
  bsnMobileStationRssiDataLastHeard Counter32

BsnTagEntry  
SEQUENCE    
  bsnTagDot11MacAddress MacAddress
  bsnTagType INTEGER
  bsnTagTimeInterval Unsigned32
  bsnTagBatteryStatus INTEGER
  bsnTagLastReported Unsigned32

BsnTagStatsEntry  
SEQUENCE    
  bsnTagBytesReceived Unsigned32
  bsnTagPacketsReceived Unsigned32

BsnTagRssiDataEntry  
SEQUENCE    
  bsnTagRssiDataApMacAddress MacAddress
  bsnTagRssiDataApIfSlotId Unsigned32
  bsnTagRssiDataApIfType INTEGER
  bsnTagRssiDataApName DisplayString
  bsnTagRssiDataLastHeard Counter32
  bsnTagRssiData Integer32
  bsnTagRssiDataSnr Integer32

BsnWatchListClientEntry  
SEQUENCE    
  bsnWatchListClientKey OCTET STRING
  bsnWatchListClientType INTEGER
  bsnWatchListClientRowStatus RowStatus

BsnRogueAPEntry  
SEQUENCE    
  bsnRogueAPDot11MacAddress MacAddress
  bsnRogueAPTotalDetectingAPs Integer32
  bsnRogueAPFirstReported DisplayString
  bsnRogueAPLastReported DisplayString
  bsnRogueAPContainmentLevel INTEGER
  bsnRogueAPType INTEGER
  bsnRogueAPOnNetwork INTEGER
  bsnRogueAPTotalClients Integer32
  bsnRogueAPRowStatus RowStatus
  bsnRogueAPMaxDetectedRSSI Integer32
  bsnRogueAPSSID DisplayString
  bsnRogueAPDetectingAPRadioType BITS
  bsnRogueAPDetectingAPMacAddress MacAddress
  bsnRogueAPMaxRssiRadioType INTEGER
  bsnRogueAPState INTEGER
  bsnRogueAPClassType INTEGER
  bsnRogueAPChannel Integer32
  bsnRogueAPDetectingAPName OCTET STRING

BsnRogueAPAirespaceAPEntry  
SEQUENCE    
  bsnRogueAPAirespaceAPMacAddress MacAddress
  bsnRogueAPAirespaceAPSlotId Unsigned32
  bsnRogueAPRadioType INTEGER
  bsnRogueAPAirespaceAPName DisplayString
  bsnRogueAPChannelNumber Integer32
  bsnRogueAPSsid DisplayString
  bsnRogueAPAirespaceAPRSSI Integer32
  bsnRogueAPContainmentMode INTEGER
  bsnRogueAPContainmentChannelCount Unsigned32
  bsnRogueAPContainmentChannels DisplayString
  bsnRogueAPAirespaceAPLastHeard Counter32
  bsnRogueAPAirespaceAPWepMode INTEGER
  bsnRogueAPAirespaceAPPreamble INTEGER
  bsnRogueAPAirespaceAPWpaMode INTEGER
  bsnRogueAPAirespaceAPSNR Integer32
  bsnRogueAPChannelWidth INTEGER

BsnRogueClientPerRogueAPEntry  
SEQUENCE    
  bsnRogueAPDot11MacAddr MacAddress
  bsnRogueClientDot11MacAddr MacAddress

BsnRogueClientEntry  
SEQUENCE    
  bsnRogueClientDot11MacAddress MacAddress
  bsnRogueClientTotalDetectingAPs Integer32
  bsnRogueClientFirstReported DisplayString
  bsnRogueClientLastReported DisplayString
  bsnRogueClientBSSID MacAddress
  bsnRogueClientContainmentLevel INTEGER
  bsnRogueClientLastHeard Integer32
  bsnRogueClientState INTEGER

BsnRogueClientAirespaceAPEntry  
SEQUENCE    
  bsnRogueClientAirespaceAPMacAddress MacAddress
  bsnRogueClientAirespaceAPSlotId Unsigned32
  bsnRogueClientRadioType INTEGER
  bsnRogueClientAirespaceAPName DisplayString
  bsnRogueClientChannelNumber Integer32
  bsnRogueClientAirespaceAPRSSI Integer32
  bsnRogueClientAirespaceAPLastHeard DisplayString
  bsnRogueClientAirespaceAPSNR Integer32

BsnThirdPartyAPEntry  
SEQUENCE    
  bsnThirdPartyAPMacAddress MacAddress
  bsnThirdPartyAPInterface Integer32
  bsnThirdPartyAPIpAddress IpAddress
  bsnThirdPartyAP802Dot1XRequired INTEGER
  bsnThirdPartyAPMirrorMode INTEGER
  bsnThirdPartyAPRowStatus RowStatus

BsnAPEntry  
SEQUENCE    
  bsnAPDot3MacAddress MacAddress
  bsnAPNumOfSlots INTEGER
  bsnAPName OCTET STRING
  bsnAPLocation OCTET STRING
  bsnAPMonitorOnlyMode INTEGER
  bsnAPOperationStatus INTEGER
  bsnAPSoftwareVersion DisplayString
  bsnAPBootVersion DisplayString
  bsnAPPrimaryMwarName OCTET STRING
  bsnAPReset INTEGER
  bsnAPStatsTimer INTEGER
  bsnAPPortNumber INTEGER
  bsnAPModel DisplayString
  bsnAPSerialNumber DisplayString
  bsnAPClearConfig INTEGER
  bsnApIpAddress IpAddress
  bsnAPMirrorMode INTEGER
  bsnAPRemoteModeSupport INTEGER
  bsnAPType INTEGER
  bsnAPSecondaryMwarName OCTET STRING
  bsnAPTertiaryMwarName OCTET STRING
  bsnAPIsStaticIP INTEGER
  bsnAPNetmask IpAddress
  bsnAPGateway IpAddress
  bsnAPStaticIPAddress IpAddress
  bsnAPBridgingSupport INTEGER
  bsnAPGroupVlanName OCTET STRING
  bsnAPIOSVersion DisplayString
  bsnAPCertificateType INTEGER
  bsnAPEthernetMacAddress MacAddress
  bsnAPAdminStatus INTEGER

BsnAPIfEntry  
SEQUENCE    
  bsnAPIfSlotId Unsigned32
  bsnAPIfType INTEGER
  bsnAPIfPhyChannelAssignment INTEGER
  bsnAPIfPhyChannelNumber INTEGER
  bsnAPIfPhyTxPowerControl INTEGER
  bsnAPIfPhyTxPowerLevel INTEGER
  bsnAPIfPhyAntennaMode INTEGER
  bsnAPIfPhyAntennaType INTEGER
  bsnAPIfPhyAntennaDiversity INTEGER
  bsnAPIfCellSiteConfigId Unsigned32
  bsnAPIfNumberOfVaps INTEGER
  bsnAPIfOperStatus INTEGER
  bsnAPIfPortNumber INTEGER
  bsnAPIfPhyAntennaOptions INTEGER
  bsnApIfNoOfUsers Counter32
  bsnAPIfWlanOverride INTEGER
  bsnAPIfPacketsSniffingFeature INTEGER
  bsnAPIfSniffChannel INTEGER
  bsnAPIfSniffServerIPAddress IpAddress
  bsnAPIfAntennaGain INTEGER
  bsnAPIfChannelList DisplayString
  bsnAPIfAbsolutePowerList DisplayString
  bsnAPIfRegulatoryDomainSupport INTEGER
  bsnAPIfAdminStatus INTEGER

BsnAPIfWlanOverrideEntry  
SEQUENCE    
  bsnAPIfWlanOverrideId Unsigned32
  bsnAPIfWlanOverrideSsid DisplayString
  bsnAPIfWlanOverrideRowStatus RowStatus

BsnAPIfSmtParamEntry  
SEQUENCE    
  bsnAPIfDot11BeaconPeriod INTEGER
  bsnAPIfDot11MediumOccupancyLimit INTEGER
  bsnAPIfDot11CFPPeriod INTEGER
  bsnAPIfDot11CFPMaxDuration INTEGER
  bsnAPIfDot11OperationalRateSet OCTET STRING
  bsnAPIfDot11DTIMPeriod INTEGER
  bsnAPIfDot11MultiDomainCapabilityImplemented INTEGER
  bsnAPIfDot11MultiDomainCapabilityEnabled INTEGER
  bsnAPIfDot11CountryString OCTET STRING
  bsnAPIfDot11SmtParamsConfigType INTEGER
  bsnAPIfDot11BSSID MacAddress

BsnAPIfMultiDomainCapabilityEntry  
SEQUENCE    
  bsnAPIfDot11MaximumTransmitPowerLevel Integer32
  bsnAPIfDot11FirstChannelNumber Integer32
  bsnAPIfDot11NumberofChannels Integer32

BsnAPIfMacOperationParamEntry  
SEQUENCE    
  bsnAPIfDot11MacRTSThreshold INTEGER
  bsnAPIfDot11MacShortRetryLimit INTEGER
  bsnAPIfDot11MacLongRetryLimit INTEGER
  bsnAPIfDot11MacFragmentationThreshold INTEGER
  bsnAPIfDot11MacMaxTransmitMSDULifetime Unsigned32
  bsnAPIfDot11MacParamsConfigType INTEGER
  bsnAPIfDot11MacMaxReceiveLifetime Unsigned32

BsnAPIfDot11CountersEntry  
SEQUENCE    
  bsnAPIfDot11TransmittedFragmentCount Counter32
  bsnAPIfDot11MulticastTransmittedFrameCount Counter32
  bsnAPIfDot11RetryCount Counter32
  bsnAPIfDot11MultipleRetryCount Counter32
  bsnAPIfDot11FrameDuplicateCount Counter32
  bsnAPIfDot11RTSSuccessCount Counter32
  bsnAPIfDot11RTSFailureCount Counter32
  bsnAPIfDot11ACKFailureCount Counter32
  bsnAPIfDot11ReceivedFragmentCount Counter32
  bsnAPIfDot11MulticastReceivedFrameCount Counter32
  bsnAPIfDot11FCSErrorCount Counter32
  bsnAPIfDot11TransmittedFrameCount Counter32
  bsnAPIfDot11WEPUndecryptableCount Counter32
  bsnAPIfDot11FailedCount Counter32

BsnAPIfDot11PhyTxPowerEntry  
SEQUENCE    
  bsnAPIfDot11NumberSupportedPowerLevels INTEGER
  bsnAPIfDot11TxPowerLevel1 INTEGER
  bsnAPIfDot11TxPowerLevel2 INTEGER
  bsnAPIfDot11TxPowerLevel3 INTEGER
  bsnAPIfDot11TxPowerLevel4 INTEGER
  bsnAPIfDot11TxPowerLevel5 INTEGER
  bsnAPIfDot11TxPowerLevel6 INTEGER
  bsnAPIfDot11TxPowerLevel7 INTEGER
  bsnAPIfDot11TxPowerLevel8 INTEGER

BsnAPIfDot11PhyChannelEntry  
SEQUENCE    
  bsnAPIfDot11CurrentCCAMode INTEGER
  bsnAPIfDot11EDThreshold Integer32
  bsnAPIfDot11TIThreshold Integer32

BsnAPIfProfileThresholdConfigEntry  
SEQUENCE    
  bsnAPIfProfileParamAssignment INTEGER
  bsnAPIfForeignInterferenceThreshold INTEGER
  bsnAPIfForeignNoiseThreshold INTEGER
  bsnAPIfRFUtilizationThreshold INTEGER
  bsnAPIfThroughputThreshold Unsigned32
  bsnAPIfMobilesThreshold INTEGER
  bsnAPIfCoverageThreshold INTEGER
  bsnAPIfMobileMinExceptionLevel INTEGER
  bsnAPIfCoverageExceptionLevel INTEGER

BsnAPIfLoadParametersEntry  
SEQUENCE    
  bsnAPIfLoadRxUtilization INTEGER
  bsnAPIfLoadTxUtilization INTEGER
  bsnAPIfLoadChannelUtilization INTEGER
  bsnAPIfLoadNumOfClients Integer32
  bsnAPIfPoorSNRClients Integer32

BsnAPIfChannelInterferenceInfoEntry  
SEQUENCE    
  bsnAPIfInterferenceChannelNo Integer32
  bsnAPIfInterferencePower Integer32
  bsnAPIfInterferenceUtilization INTEGER

BsnAPIfRadarChannelStatisticsEntry  
SEQUENCE    
  bsnAPIfRadarDetectedChannelNumber Integer32
  bsnAPIfRadarSignalLastHeard Integer32

BsnAPIfChannelNoiseInfoEntry  
SEQUENCE    
  bsnAPIfNoiseChannelNo Integer32
  bsnAPIfDBNoisePower Integer32

BsnAPIfProfileStateEntry  
SEQUENCE    
  bsnAPIfLoadProfileState ProfileState
  bsnAPIfInterferenceProfileState ProfileState
  bsnAPIfNoiseProfileState ProfileState
  bsnAPIfCoverageProfileState ProfileState

BsnAPIfRxNeighborsEntry  
SEQUENCE    
  bsnAPIfRxNeighborMacAddress MacAddress
  bsnAPIfRxNeighborIpAddress IpAddress
  bsnAPIfRxNeighborRSSI Integer32
  bsnAPIfRxNeighborSlot Integer32
  bsnAPIfRxNeighborChannel Integer32
  bsnAPIfRxNeighborChannelWidth INTEGER

BsnMeshNodeEntry  
SEQUENCE    
  bsnMeshNodeRole INTEGER
  bsnMeshNodeGroup OCTET STRING
  bsnMeshNodeBackhaul INTEGER
  bsnMeshNodeBackhaulPAP INTEGER
  bsnMeshNodeBackhaulRAP INTEGER
  bsnMeshNodeDataRate Integer32
  bsnMeshNodeChannel Integer32
  bsnMeshNodeRoutingState INTEGER
  bsnMeshNodeMalformedNeighPackets Counter32
  bsnMeshNodePoorNeighSnr Counter32
  bsnMeshNodeBlacklistPackets Counter32
  bsnMeshNodeInsufficientMemory Counter32
  bsnMeshNodeRxNeighReq Counter32
  bsnMeshNodeRxNeighRsp Counter32
  bsnMeshNodeTxNeighReq Counter32
  bsnMeshNodeTxNeighRsp Counter32
  bsnMeshNodeParentChanges Counter32
  bsnMeshNodeNeighTimeout Counter32
  bsnMeshNodeParentMacAddress MacAddress
  bsnMeshNodeAPType INTEGER
  bsnMeshNodeEthernetBridge INTEGER
  bsnMeshNodeHops Integer32

BsnMeshNeighsEntry  
SEQUENCE    
  bsnMeshNeighMacAddress MacAddress
  bsnMeshNeighType INTEGER
  bsnMeshNeighState INTEGER
  bsnMeshNeighSnr Integer32
  bsnMeshNeighSnrUp Integer32
  bsnMeshNeighSnrDown Integer32
  bsnMeshNeighLinkSnr Integer32
  bsnMeshNeighAdjustedEase Integer32
  bsnMeshNeighUnadjustedEase Integer32
  bsnMeshNeighRapEase Integer32
  bsnMeshNeighTxParent Counter32
  bsnMeshNeighRxParent Counter32
  bsnMeshNeighPoorSnr Counter32
  bsnMeshNeighLastUpdate Integer32
  bsnMeshNeighParentChange Integer32

BsnAPIfStationRSSICoverageInfoEntry  
SEQUENCE    
  bsnAPIfStationRSSICoverageIndex Integer32
  bsnAPIfRSSILevel Integer32
  bsnAPIfStationCountOnRSSI Integer32

BsnAPIfStationSNRCoverageInfoEntry  
SEQUENCE    
  bsnAPIfStationSNRCoverageIndex Integer32
  bsnAPIfSNRLevel Integer32
  bsnAPIfStationCountOnSNR Integer32

BsnAPIfRecommendedRFParametersEntry  
SEQUENCE    
  bsnAPIfRecommendedChannelNumber Integer32
  bsnAPIfRecommendedTxPowerLevel Integer32
  bsnAPIfRecommendedRTSThreshold Integer32
  bsnAPIfRecommendedFragmentationThreshold Integer32

BsnStandardSignatureEntry  
SEQUENCE    
  bsnStandardSignaturePrecedence Unsigned32
  bsnStandardSignatureName DisplayString
  bsnStandardSignatureDescription DisplayString
  bsnStandardSignatureFrameType INTEGER
  bsnStandardSignatureAction INTEGER
  bsnStandardSignatureState INTEGER
  bsnStandardSignatureFrequency Unsigned32
  bsnStandardSignatureQuietTime Unsigned32
  bsnStandardSignatureVersion Unsigned32
  bsnStandardSignatureConfigType INTEGER
  bsnStandardSignatureEnable TruthValue
  bsnStandardSignatureMacInfo BsnTxtSignatureMacInfo
  bsnStandardSignatureMacFreq Unsigned32
  bsnStandardSignatureRowStatus RowStatus
  bsnStandardSignatureInterval Unsigned32

BsnStandardSignaturePatternEntry  
SEQUENCE    
  bsnStandardSignaturePatternIndex Unsigned32
  bsnStandardSignaturePatternOffset Unsigned32
  bsnStandardSignaturePatternString DisplayString
  bsnStandardSignaturePatternMask DisplayString
  bsnStandardSignaturePatternOffSetStart BsnSignaturePatternOffSetStart
  bsnStandardSignaturePatternRowStatus RowStatus

BsnCustomSignatureEntry  
SEQUENCE    
  bsnCustomSignaturePrecedence Unsigned32
  bsnCustomSignatureName DisplayString
  bsnCustomSignatureDescription DisplayString
  bsnCustomSignatureFrameType INTEGER
  bsnCustomSignatureAction INTEGER
  bsnCustomSignatureState INTEGER
  bsnCustomSignatureFrequency Unsigned32
  bsnCustomSignatureQuietTime Unsigned32
  bsnCustomSignatureVersion Unsigned32
  bsnCustomSignatureConfigType INTEGER
  bsnCustomSignatureEnable TruthValue
  bsnCustomSignatureMacInfo BsnTxtSignatureMacInfo
  bsnCustomSignatureMacFreq Unsigned32
  bsnCustomSignatureRowStatus RowStatus
  bsnCustomSignatureInterval Unsigned32

BsnCustomSignaturePatternEntry  
SEQUENCE    
  bsnCustomSignaturePatternIndex Unsigned32
  bsnCustomSignaturePatternOffset Unsigned32
  bsnCustomSignaturePatternString DisplayString
  bsnCustomSignaturePatternMask DisplayString
  bsnCustomSignaturePatternOffSetStart BsnSignaturePatternOffSetStart
  bsnCustomSignaturePatternRowStatus RowStatus

BsnWrasDot11aGroupEntry  
SEQUENCE    
  bsnWrasDot11aPeerMacAddress MacAddress
  bsnWrasDot11aPeerIpAddress IpAddress

BsnWrasDot11bGroupEntry  
SEQUENCE    
  bsnWrasDot11bPeerMacAddress MacAddress
  bsnWrasDot11bPeerIpAddress IpAddress

BsnRadiusAuthServerEntry  
SEQUENCE    
  bsnRadiusAuthServerIndex Integer32
  bsnRadiusAuthServerAddress IpAddress
  bsnRadiusAuthClientServerPortNumber Integer32
  bsnRadiusAuthServerKey OCTET STRING
  bsnRadiusAuthServerStatus INTEGER
  bsnRadiusAuthServerKeyFormat INTEGER
  bsnRadiusAuthServerRFC3576 INTEGER
  bsnRadiusAuthServerIPSec INTEGER
  bsnRadiusAuthServerIPSecAuth INTEGER
  bsnRadiusAuthServerIPSecEncryption INTEGER
  bsnRadiusAuthServerIPSecIKEPhase1 INTEGER
  bsnRadiusAuthServerIPSecIKELifetime Integer32
  bsnRadiusAuthServerIPSecDHGroup INTEGER
  bsnRadiusAuthServerNetworkUserConfig INTEGER
  bsnRadiusAuthServerMgmtUserConfig INTEGER
  bsnRadiusAuthServerRetransmitTimeout INTEGER
  bsnRadiusAuthServerKeyWrapKEKkey OCTET STRING
  bsnRadiusAuthServerKeyWrapMACKkey OCTET STRING
  bsnRadiusAuthServerKeyWrapFormat INTEGER
  bsnRadiusAuthServerRowStatus RowStatus

BsnRadiusAccServerEntry  
SEQUENCE    
  bsnRadiusAccServerIndex Integer32
  bsnRadiusAccServerAddress IpAddress
  bsnRadiusAccClientServerPortNumber Integer32
  bsnRadiusAccServerKey OCTET STRING
  bsnRadiusAccServerStatus INTEGER
  bsnRadiusAccServerKeyFormat INTEGER
  bsnRadiusAccServerIPSec INTEGER
  bsnRadiusAccServerIPSecAuth INTEGER
  bsnRadiusAccServerIPSecEncryption INTEGER
  bsnRadiusAccServerIPSecIKEPhase1 INTEGER
  bsnRadiusAccServerIPSecIKELifetime Integer32
  bsnRadiusAccServerIPSecDHGroup INTEGER
  bsnRadiusAccServerNetworkUserConfig INTEGER
  bsnRadiusAccServerRetransmitTimeout INTEGER
  bsnRadiusAccServerRowStatus RowStatus

BsnRadiusAuthServerStatsEntry  
SEQUENCE    
  bsnRadiusAuthClientRoundTripTime TimeTicks
  bsnRadiusAuthClientAccessRequests Counter32
  bsnRadiusAuthClientAccessRetransmissions Counter32
  bsnRadiusAuthClientAccessAccepts Counter32
  bsnRadiusAuthClientAccessRejects Counter32
  bsnRadiusAuthClientAccessChallenges Counter32
  bsnRadiusAuthClientMalformedAccessResponses Counter32
  bsnRadiusAuthClientBadAuthenticators Counter32
  bsnRadiusAuthClientPendingRequests Gauge32
  bsnRadiusAuthClientTimeouts Counter32
  bsnRadiusAuthClientUnknownTypes Counter32
  bsnRadiusAuthClientPacketsDropped Counter32

BsnRadiusAccServerStatsEntry  
SEQUENCE    
  bsnRadiusAccClientRoundTripTime TimeTicks
  bsnRadiusAccClientRequests Counter32
  bsnRadiusAccClientRetransmissions Counter32
  bsnRadiusAccClientResponses Counter32
  bsnRadiusAccClientMalformedResponses Counter32
  bsnRadiusAccClientBadAuthenticators Counter32
  bsnRadiusAccClientPendingRequests Gauge32
  bsnRadiusAccClientTimeouts Counter32
  bsnRadiusAccClientUnknownTypes Counter32
  bsnRadiusAccClientPacketsDropped Counter32

BsnUsersEntry  
SEQUENCE    
  bsnUserName OCTET STRING
  bsnUserPassword OCTET STRING
  bsnUserEssIndex INTEGER
  bsnUserAccessMode INTEGER
  bsnUserType INTEGER
  bsnUserInterfaceName OCTET STRING
  bsnUserRowStatus RowStatus

BsnMacFilterEntry  
SEQUENCE    
  bsnMacFilterAddress OCTET STRING
  bsnMacFilterWlanId INTEGER
  bsnMacFilterInterfaceName OCTET STRING
  bsnMacFilterDescription OCTET STRING
  bsnMacFilterRowStatus RowStatus

BsnLocalNetUserEntry  
SEQUENCE    
  bsnLocalNetUserName OCTET STRING
  bsnLocalNetUserWlanId INTEGER
  bsnLocalNetUserPassword OCTET STRING
  bsnLocalNetUserDescription OCTET STRING
  bsnLocalNetUserLifetime TimeInterval
  bsnLocalNetUserStartTime TimeTicks
  bsnLocalNetUserRemainingTime TimeInterval
  bsnLocalNetUserRowStatus RowStatus

BsnLocalManagementUserEntry  
SEQUENCE    
  bsnLocalManagementUserName OCTET STRING
  bsnLocalManagementUserPassword OCTET STRING
  bsnLocalManagementUserAccessMode INTEGER
  bsnLocalManagementUserRowStatus RowStatus

BsnAclEntry  
SEQUENCE    
  bsnAclName OCTET STRING
  bsnAclApplyMode INTEGER
  bsnAclRowStatus RowStatus

BsnAclRuleEntry  
SEQUENCE    
  bsnAclRuleIndex Unsigned32
  bsnAclRuleAction INTEGER
  bsnAclRuleDirection INTEGER
  bsnAclRuleSourceIpAddress IpAddress
  bsnAclRuleSourceIpNetmask IpAddress
  bsnAclRuleDestinationIpAddress IpAddress
  bsnAclRuleDestinationIpNetmask IpAddress
  bsnAclRuleProtocol Unsigned32
  bsnAclRuleStartSourcePort Unsigned32
  bsnAclRuleEndSourcePort Unsigned32
  bsnAclRuleStartDestinationPort Unsigned32
  bsnAclRuleEndDestinationPort Unsigned32
  bsnAclRuleDscp Unsigned32
  bsnAclNewRuleIndex Unsigned32
  bsnAclRuleRowStatus RowStatus

BsnBlackListClientEntry  
SEQUENCE    
  bsnBlackListClientMacAddress OCTET STRING
  bsnBlackListClientDescription OCTET STRING
  bsnBlackListClientRowStatus RowStatus

BsnExternalPolicyServerEntry  
SEQUENCE    
  bsnExternalPolicyServerIndex Integer32
  bsnExternalPolicyServerAddress IpAddress
  bsnExternalPolicyServerPortNumber Integer32
  bsnExternalPolicyServerKey OCTET STRING
  bsnExternalPolicyServerAdminStatus INTEGER
  bsnExternalPolicyServerConnectionStatus INTEGER
  bsnExternalPolicyServerRowStatus RowStatus

BsnAPAuthorizationEntry  
SEQUENCE    
  bsnAPAuthMacAddress OCTET STRING
  bsnAPAuthCertificateType INTEGER
  bsnAPAuthHashKey OCTET STRING
  bsnAPAuthRowStatus RowStatus

BsnWrasIpsecCertEntry  
SEQUENCE    
  bsnWrasIpsecCertName DisplayString
  bsnWrasIpsecCertificateUpdate OCTET STRING
  bsnWrasIpsecCertificate OCTET STRING
  bsnWrasIpsecCertPassword OCTET STRING
  bsnWrasIpsecCertStatus RowStatus

BsnPingTestEntry  
SEQUENCE    
  bsnPingTestId Integer32
  bsnPingTestIPAddress IpAddress
  bsnPingTestSendCount Integer32
  bsnPingTestReceivedCount Integer32
  bsnPingTestStatus INTEGER
  bsnPingTestMaxTimeInterval Unsigned32
  bsnPingTestMinTimeInterval Unsigned32
  bsnPingTestAvgTimeInterval Unsigned32
  bsnPingTestRowStatus RowStatus

BsnLinkTestEntry  
SEQUENCE    
  bsnLinkTestId Integer32
  bsnLinkTestMacAddress MacAddress
  bsnLinkTestSendPktCount Integer32
  bsnLinkTestSendPktLength Integer32
  bsnLinkTestReceivedPktCount Integer32
  bsnLinkTestClientRSSI Integer32
  bsnLinkTestLocalSNR Integer32
  bsnLinkTestLocalRSSI Integer32
  bsnLinkTestStatus INTEGER
  bsnLinkTestRowStatus RowStatus

BsnMobilityGroupMembersEntry  
SEQUENCE    
  bsnMobilityGroupMemberMacAddress MacAddress
  bsnMobilityGroupMemberIPAddress IpAddress
  bsnMobilityGroupMemberGroupName DisplayString
  bsnMobilityGroupMemberRowStatus RowStatus

BsnMobilityAnchorsEntry  
SEQUENCE    
  bsnMobilityAnchorWlanSsid DisplayString
  bsnMobilityAnchorSwitchIPAddress IpAddress
  bsnMobilityAnchorRowStatus RowStatus

BsnMobilityGroupDirectoryEntry  
SEQUENCE    
  bsnGroupDirectoryMemberIPAddress IpAddress
  bsnGroupDirectoryMemberMacAddress MacAddress
  bsnGroupDirectoryDicoveryType INTEGER
  bsnMemberCurrentAnchoredClients Counter32
  bsnMemberTotalAnchoredClients Counter32
  bsnMemberCurrentExportedClients Counter32
  bsnMemberTotalExportedClients Counter32
  bsnMemberCurrentImportedClients Counter32
  bsnMemberTotalImportedClients Counter32
  bsnMemberTotalHandoffErrors Counter32
  bsnMemberTotalCommunicationErrors Counter32

BsnAPGroupsVlanEntry  
SEQUENCE    
  bsnAPGroupsVlanName OCTET STRING
  bsnAPGroupsVlanDescription OCTET STRING
  bsnAPGroupsVlanRowStatus RowStatus

BsnAPGroupsVlanMappingEntry  
SEQUENCE    
  bsnAPGroupsVlanMappingSsid DisplayString
  bsnAPGroupsVlanMappingInterfaceName OCTET STRING
  bsnAPGroupsVlanMappingRowStatus RowStatus

Defined Values

bsnWireless 1.3.6.1.4.1.14179.2
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information for 802.11 Access Points, LAN configuration, AAA, Mobility, IpSec, Radio Rescouce Management and 802.11 global parameters. The relationship between controller and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
MODULE-IDENTITY    

bsnEss 1.3.6.1.4.1.14179.2.1
OBJECT IDENTIFIER    

bsnAP 1.3.6.1.4.1.14179.2.2
OBJECT IDENTIFIER    

bsnGlobalDot11 1.3.6.1.4.1.14179.2.3
OBJECT IDENTIFIER    

bsnRrm 1.3.6.1.4.1.14179.2.4
OBJECT IDENTIFIER    

bsnAAA 1.3.6.1.4.1.14179.2.5
OBJECT IDENTIFIER    

bsnTrap 1.3.6.1.4.1.14179.2.6
OBJECT IDENTIFIER    

bsnUtility 1.3.6.1.4.1.14179.2.7
OBJECT IDENTIFIER    

bsnMobility 1.3.6.1.4.1.14179.2.8
OBJECT IDENTIFIER    

bsnIpsec 1.3.6.1.4.1.14179.2.9
OBJECT IDENTIFIER    

bsnWrasGroups 1.3.6.1.4.1.14179.2.50
OBJECT IDENTIFIER    

bsnWrasCompliances 1.3.6.1.4.1.14179.2.51
OBJECT IDENTIFIER    

bsnDot11EssTable 1.3.6.1.4.1.14179.2.1.1
Ess(WLAN) Configuration Table indexed by bsnDot11EssIndex. Maximum of 17 WLANs can be created on Airespace Switch. bsnDot11EssIndex of 17 is reserved for WLAN for Third Party APs(non-Airespace APs).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnDot11EssEntry

bsnDot11EssEntry 1.3.6.1.4.1.14179.2.1.1.1
An entry in bsnDot11EssTable
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnDot11EssEntry  

bsnDot11EssIndex 1.3.6.1.4.1.14179.2.1.1.1.1
Index of the Ess(WLAN) within Airespace Switch. Airespace Switch supports 517 ESS(Wlans) so index will be from 1 to 517. 517 is to be used for ESS(WLAN) created for support of Third Party APs(non-Airespace APs)
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..517  

bsnDot11EssSsid 1.3.6.1.4.1.14179.2.1.1.1.2
SSID assigned to ESS(WLAN)
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..32)  

bsnDot11EssSessionTimeout 1.3.6.1.4.1.14179.2.1.1.1.4
Maximum time of a Mobile Station session. Value of 0 means infinite time(no timeout set).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..86400  

bsnDot11EssMacFiltering 1.3.6.1.4.1.14179.2.1.1.1.5
A type of security policy for Mobile Stations (Clients). Select to filter clients by MAC address. By selecting this Security, you need to create MacFilters in bsnUsersTable or have MacFilters configured on Radius Servers specified in bsnRadiusAuthenticationTable
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssAdminStatus 1.3.6.1.4.1.14179.2.1.1.1.6
Administrative Status of ESS(WLAN). By disabling an ESS the corresponding SSID is no longer broadcasted in AP beacons.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssSecurityAuthType 1.3.6.1.4.1.14179.2.1.1.1.7
Type of 802.11 Authentication.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER authOpen(0), authSharedKey(1), authCiscoLeap(128)  

bsnDot11EssStaticWEPSecurity 1.3.6.1.4.1.14179.2.1.1.1.8
Status of Static WEP Security policy. If enabled, WEP Encryption WEP Default Key, Key Index and Key Format should also be specified.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssStaticWEPEncryptionType 1.3.6.1.4.1.14179.2.1.1.1.9
Type of Static WEP Encryption. Length of key specified in Default Key depends on this attribute.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER wep104(0), wep40(2), wep128(3), notset(4)  

bsnDot11EssStaticWEPDefaultKey 1.3.6.1.4.1.14179.2.1.1.1.10
Static WEP Default Key. For wep104 encryption either 26 bit hex key or 13 bit ascii key should be specified. For wep40 encryption 10 bit hex key or 5 bit ascii key should be specified. For wep128 encryption 32 bit hex key or 16 bit ascii key should be specified.
Status: current Access: read-create
OBJECT-TYPE    
  WEPKeytype  

bsnDot11EssStaticWEPKeyIndex 1.3.6.1.4.1.14179.2.1.1.1.11
According to 802.11 standard 4 keys are supported. So 802.11 Mobile Stations(Client) can have upto 4 keys. This index is for informing Mobile Station which key it should use for Static WEP Authentication
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..4  

bsnDot11EssStaticWEPKeyFormat 1.3.6.1.4.1.14179.2.1.1.1.12
This is not persistant.Reading this attribute will always return default. The format of the key specified in Airespace switch keeps record of the Index.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER hex(1), ascii(2), default(0)  

bsnDot11Ess8021xSecurity 1.3.6.1.4.1.14179.2.1.1.1.13
Status of 802.1X security policy.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11Ess8021xEncryptionType 1.3.6.1.4.1.14179.2.1.1.1.14
Type of 802.1X Encryption. This applies if bsnDot11Ess8021xSecurity is in enabled state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER wep104(0), wep40(2), wep128(3), none(4)  

bsnDot11EssWPASecurity 1.3.6.1.4.1.14179.2.1.1.1.16
Status of WPA security policy. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssWPAEncryptionType 1.3.6.1.4.1.14179.2.1.1.1.17
Type of WPA Encryption. This applies when bsnDot11EssWPASecurity is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER wep104(0), wep40(2), wep128(3), tkipmic(5)  

bsnDot11EssIpsecSecurity 1.3.6.1.4.1.14179.2.1.1.1.18
Status of IpSec (VPN) security policy. Note that this cannot be applied with Web security policy.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssVpnEncrTransform 1.3.6.1.4.1.14179.2.1.1.1.19
The Encryption algorithm employed by this Vpn(IpSec) Encryption. This applies only when bsnDot11EssIpsecSecurity is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tripleDes(0), none(1), des(2), aesCbc(3)  

bsnDot11EssVpnAuthTransform 1.3.6.1.4.1.14179.2.1.1.1.20
The Hash algorithm employed by the Vpn Encrpytion. This applies only when bsnDot11EssIpsecSecurity is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), hmacMd5(2), hmacSha1(0)  

bsnDot11EssVpnIkeAuthMode 1.3.6.1.4.1.14179.2.1.1.1.21
The authentication type of the SA. It could be a certificate or a pre-shared key or xauthEnablePsk. This applies only when bsnDot11EssIpsecSecurity is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER xauthEnablePsk(0), certificate(2), presharedKey(3)  

bsnDot11EssVpnSharedKey 1.3.6.1.4.1.14179.2.1.1.1.22
VPN Shared Key. This applies only when bsnDot11EssVpnSharedKey is in enable state and bsnDot11EssVpnIkeAuthMode is xauthEnablePsk or presharedKey.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..128)  

bsnDot11EssVpnSharedKeySize 1.3.6.1.4.1.14179.2.1.1.1.23
VPN Shared Key size. This applies only when bsnDot11EssVpnSharedKey is in enable state and bsnDot11EssVpnIkeAuthMode is xauthEnablePsk or presharedKey.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..128  

bsnDot11EssVpnIkePhase1Mode 1.3.6.1.4.1.14179.2.1.1.1.24
VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnDot11EssIpsecSecurity is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER agressive(0), main(1)  

bsnDot11EssVpnIkeLifetime 1.3.6.1.4.1.14179.2.1.1.1.25
Vpn IKE's Lifetime. This applies only when bsnDot11EssIpsecSecurity is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1800..345600  

bsnDot11EssVpnIkeDHGroup 1.3.6.1.4.1.14179.2.1.1.1.26
IKE's Diffie-Hellman Group. This applies only when bsnDot11EssIpsecSecurity is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER group2(0), group1(1), group5(4)  

bsnDot11EssIpsecPassthruSecurity 1.3.6.1.4.1.14179.2.1.1.1.27
Status of IpSec Passthru security policy.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssVpnPassthruGateway 1.3.6.1.4.1.14179.2.1.1.1.28
Ip address of VpnPassthru Gateway. This applies only when bsnDot11EssIpsecPassthruSecurity is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnDot11EssWebSecurity 1.3.6.1.4.1.14179.2.1.1.1.29
Status of Web security policy. Note this policy cannot be applied with IpSec security policy.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssRadioPolicy 1.3.6.1.4.1.14179.2.1.1.1.30
Radio Policy for a WLAN. It can either be All where it will be applicable to ALL types of protocols or it can be set to apply to combinations of 802.11a, 802.11b, 802.11g.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER all(0), dot11aOnly(2), dot11bOnly(1), dot11gOnly(3), dot11bgOnly(4), dot11agOnly(5), dot11abOnly(6)  

bsnDot11EssQualityOfService 1.3.6.1.4.1.14179.2.1.1.1.31
Quality of Service for a WLAN.Services such as VoIP should be set to Gold while non-discriminating services such as messaging can be set to Bronze.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER bronze(0), silver(1), gold(2), platinum(3)  

bsnDot11EssDhcpRequired 1.3.6.1.4.1.14179.2.1.1.1.32
DHCP required for all clients on this WLAN
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssDhcpServerIpAddress 1.3.6.1.4.1.14179.2.1.1.1.33
IP Address of the DHCP Server. Make it 0.0.0.0 to disable DHCP Relay. Any value other than 0.0.0.0, it will be assumed that DHCP Relay is turned on.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnDot11EssVpnContivityMode 1.3.6.1.4.1.14179.2.1.1.1.34
Specifies if contivity mode for the IpSec is enabled. If enabled, user needs to specify the Quote of the Day Server's IPAddress in bsnDot11EssVpnQotdServerAddress.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssVpnQotdServerAddress 1.3.6.1.4.1.14179.2.1.1.1.35
IP Address of the Quote of the Day Server.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnDot11EssBlacklistTimeout 1.3.6.1.4.1.14179.2.1.1.1.37
Set the timeout for blacklisted Mobile Stations after which the mobile station will be automatically de-authenticated. Mobile Station are blacklisted by MAC address and their status can be obtained from bsnMobileStationStatus. A timeout setting of 0 indicates no blacklist timeout is set and administrative control (bsnMobileStationDeleteAction ) is required to deauthenticate the station.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

bsnDot11EssNumberOfMobileStations 1.3.6.1.4.1.14179.2.1.1.1.38
No of Mobile Stations currently associated with the WLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnDot11EssWebPassthru 1.3.6.1.4.1.14179.2.1.1.1.39
For switches with version before 2.0: This is applicable only when the Web Security Type is enabled. When this attribute is enabled, it allows a client's NetBIOS packets to go through the switch before web auth is completed. (This is obsolete for Switch versions 2.0 to 2.2). For switch verions 3.0 and above: This is reintroduced as the web policy where the client is connected through the web without authentication that is there is no username/password input required. Moreover, if the bsnDot11EssWebPassthroughEmail is enabled, the user will be asked to enter an email address.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssCraniteSecurity 1.3.6.1.4.1.14179.2.1.1.1.40
Status of Cranite Passthrough Security policy. If enabled, no other security can be enabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssBlacklistingCapability 1.3.6.1.4.1.14179.2.1.1.1.41
This is the flag that can enable or disable the client backlisting feature for a WLAN. If enabled, the clients can be blacklisted by the Switch in case of repetitive auth failure and other reasons like it. If disabled, the clients cannot be blacklisted by the switch. The blacklist timeout value will only be effective if this feature is turned on.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssInterfaceName 1.3.6.1.4.1.14179.2.1.1.1.42
Name of the interface used by this WLAN. By default it is set to be the management interface.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..32)  

bsnDot11EssAclName 1.3.6.1.4.1.14179.2.1.1.1.43
Name of ACL for the WLAN. This is applicable only when Web Authentication is enabled as a security. An empty string value indicates that no ACL has been set (which is a valid option)
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

bsnDot11EssAAAOverride 1.3.6.1.4.1.14179.2.1.1.1.44
Enable or Disable AAA override for the global WLAN parameters.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssWPAAuthKeyMgmtMode 1.3.6.1.4.1.14179.2.1.1.1.45
Enable or Disable WPA Pre-shared Key Mode. If enabled, a preshared key should be set for WPA authentication. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssWPAAuthPresharedKey 1.3.6.1.4.1.14179.2.1.1.1.46
WPA Authentication Preshared Key. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(8..63)  

bsnDot11EssWepAllowSharedKeyAuth 1.3.6.1.4.1.14179.2.1.1.1.48
Enable this flag to allow Shared Key Authentication when Static WEP is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssFortressSecurity 1.3.6.1.4.1.14179.2.1.1.1.47
Status of Fortress Passthrough Security policy. If enabled, no other security can be enabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssL2tpSecurity 1.3.6.1.4.1.14179.2.1.1.1.49
Status of L2TP security policy. Note that this cannot be applied with Web security policy, Cranite or Fortress policy.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssWPAAuthPresharedKeyHex 1.3.6.1.4.1.14179.2.1.1.1.50
WPA Authentication Preshared Key in the hex format. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..40)  

bsnDot11EssBroadcastSsid 1.3.6.1.4.1.14179.2.1.1.1.51
This attribute when enabled allows the switch to broadcast this SSID.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssExternalPolicyValidation 1.3.6.1.4.1.14179.2.1.1.1.52
This attribute specifies if external policy servers will be used for validation. If no servers are configured in bsnExternalPolicyServerTable then it cannot be enabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

bsnDot11EssRSNSecurity 1.3.6.1.4.1.14179.2.1.1.1.53
This attribute specifies status of RSN Security Policy. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssRSNWPACompatibilityMode 1.3.6.1.4.1.14179.2.1.1.1.54
This attribute specifies RSN security's compatibility mode with WPA. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssRSNAllowTKIPClients 1.3.6.1.4.1.14179.2.1.1.1.55
This attribute specifies whether TKIP clients are allowed by RSN Policy. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(0)  

bsnDot11EssRSNAuthKeyMgmtMode 1.3.6.1.4.1.14179.2.1.1.1.56
This attribute specifies whether Preshared key is used or not. If used user should specify a key between 8 and 63 characters in bsnDot11EssRSNAuthPresharedKey attribute. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssRSNAuthPresharedKey 1.3.6.1.4.1.14179.2.1.1.1.57
RSN Authentication Preshared Key. This applies only when bsnDot11EssRSNAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(8..63)  

bsnDot11EssRSNAuthPresharedKeyHex 1.3.6.1.4.1.14179.2.1.1.1.58
RSN Authentication Preshared Key in the hex format. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..40)  

bsnDot11EssIPv6Bridging 1.3.6.1.4.1.14179.2.1.1.1.59
When enabled, IPv6 bridging is applied on the packets.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssRowStatus 1.3.6.1.4.1.14179.2.1.1.1.60
A row status type for the bsnDot11EssEntry
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnDot11EssWmePolicySetting 1.3.6.1.4.1.14179.2.1.1.1.61
When enabled, WME Policy is applied on the packets.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), allowed(1), required(2), invalid(3)  

bsnDot11Ess80211ePolicySetting 1.3.6.1.4.1.14179.2.1.1.1.62
When enabled, 802.11e Policy is applied on the packets.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), allowed(1), required(2), invalid(3)  

bsnDot11EssWebPassthroughEmail 1.3.6.1.4.1.14179.2.1.1.1.63
When enabled, along with the bsnDot11EssWebPassthru attribute, the client is allowed to connect by entering his/her email address on the web connection page. There is no further authentication required.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11Ess7920PhoneSupport 1.3.6.1.4.1.14179.2.1.1.1.64
When client cac limit is enabled, the 7920 Phones with old software where the Call Admission Control (CAC) Limit is Specified on the client will be supported on the WLAN. The support for clientCacLimit (by setting to value 1 or 3) cannot be enabled when the bsnDot11EssWmePolicySetting is set to allowed or required. When ap cac limit is enabled, the 7920 Phones with new software where the Call Admission Control (CAC) Limit is advertised by the AP, will be supported on the WLAN.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), clientCacLimit(1), apCacLimit(2), both(3)  

bsnDot11EssRadiusAuthPrimaryServer 1.3.6.1.4.1.14179.2.1.1.1.95
Primary Radius Authentication Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

bsnDot11EssRadiusAuthSecondaryServer 1.3.6.1.4.1.14179.2.1.1.1.96
Secondary Radius Authentication Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

bsnDot11EssRadiusAuthTertiaryServer 1.3.6.1.4.1.14179.2.1.1.1.97
Tertiary Radius Authentication Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

bsnDot11EssRadiusAcctPrimaryServer 1.3.6.1.4.1.14179.2.1.1.1.98
Primary Radius Accounting Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

bsnDot11EssRadiusAcctSecondaryServer 1.3.6.1.4.1.14179.2.1.1.1.99
Secondary Radius Accounting Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

bsnDot11EssRadiusAcctTertiaryServer 1.3.6.1.4.1.14179.2.1.1.1.100
Tertiary Radius Accounting Server for this wlan.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..21)  

bsnDot11QosProfileTable 1.3.6.1.4.1.14179.2.1.17
QOS Profiles specified in bsnDot11EssTable can be customized in this table. This is a lookup table for auto created profiles
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnDot11QosProfileEntry

bsnDot11QosProfileEntry 1.3.6.1.4.1.14179.2.1.17.1
An entry in bsnDot11QosProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnDot11QosProfileEntry  

bsnDot11QosProfileName 1.3.6.1.4.1.14179.2.1.17.1.1
QOS Profile Name. This will be one of bronze,gold, platinum,silver,uranium.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

bsnDot11QosProfileDesc 1.3.6.1.4.1.14179.2.1.17.1.2
QOS Profile Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..64)  

bsnDot11QosAverageDataRate 1.3.6.1.4.1.14179.2.1.17.1.3
This is one of the per user bandwidth contracts(k). Specifies Average Data Rate per user. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..60000  

bsnDot11QosBurstDataRate 1.3.6.1.4.1.14179.2.1.17.1.4
This is one of the per user bandwidth contracts(k). Specifies Average Burst Data Rate per user. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..60000  

bsnDot11QosAvgRealTimeDataRate 1.3.6.1.4.1.14179.2.1.17.1.5
This is one of the per user bandwidth contracts(k). Specifies Average Real Time Data Rate per user. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..60000  

bsnDot11QosBurstRealTimeDataRate 1.3.6.1.4.1.14179.2.1.17.1.6
This is one of the per user bandwidth contracts(k). Specifies Burst Real Time Data Rate per user. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..60000  

bsnDot11QosMaxRFUsagePerAP 1.3.6.1.4.1.14179.2.1.17.1.7
This is one of the over the Air QOS parameter. Specifies maximum RF Usage per AP in percentage.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

bsnDot11QosProfileQueueDepth 1.3.6.1.4.1.14179.2.1.17.1.8
This is one of the over the Air QOS parameter. Specifies Queue depth for the current profile.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..255  

bsnDot11WiredQosProtocol 1.3.6.1.4.1.14179.2.1.17.1.9
This is one of the over the Air QOS parameter. Specifies Queue depth for the current profile.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), dot1p(1)  

bsnDot11802Dot1PTag 1.3.6.1.4.1.14179.2.1.17.1.10
Specifies the type of wired QOS protocol for the current profile. Value of 0 indicates the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

bsnDot11ResetProfileToDefault 1.3.6.1.4.1.14179.2.1.17.1.40
Set this attribute to reset to restore the factory default value for the profile.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), default(0)  

bsnMobileStationTable 1.3.6.1.4.1.14179.2.1.4
Mobile Station Table indexed by bsnMobileStationMacAddress. (Mobile Station is better referred to as Client in the current releases.)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationEntry

bsnMobileStationEntry 1.3.6.1.4.1.14179.2.1.4.1
An entry in bsnMobileStationTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMobileStationEntry  

bsnMobileStationMacAddress 1.3.6.1.4.1.14179.2.1.4.1.1
802.11 MAC Address of the Mobile Station.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnMobileStationIpAddress 1.3.6.1.4.1.14179.2.1.4.1.2
IP Address of the Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bsnMobileStationUserName 1.3.6.1.4.1.14179.2.1.4.1.3
User Name,if any, of the Mobile Station. This would be non empty in case of Web Authentication and IPSec.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnMobileStationAPMacAddr 1.3.6.1.4.1.14179.2.1.4.1.4
802.11 Mac Address of the AP to which the Mobile Station is associated.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnMobileStationAPIfSlotId 1.3.6.1.4.1.14179.2.1.4.1.5
Slot ID of AP Interface to which the mobile station is associated. The value 15 is used to indicate that the slot Id is invalid.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..15  

bsnMobileStationEssIndex 1.3.6.1.4.1.14179.2.1.4.1.6
Ess Index of the Wlan(SSID) that is being used by Mobile Station to connect to AP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..16  

bsnMobileStationSsid 1.3.6.1.4.1.14179.2.1.4.1.7
The SSID Advertised by Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnMobileStationAID 1.3.6.1.4.1.14179.2.1.4.1.8
AID for the mobile station
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnMobileStationStatus 1.3.6.1.4.1.14179.2.1.4.1.9
Status of the mobile station
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), aaaPending(1), authenticated(2), associated(3), powersave(4), disassociated(5), tobedeleted(6), probing(7), blacklisted(8)  

bsnMobileStationReasonCode 1.3.6.1.4.1.14179.2.1.4.1.10
Reason Code as defined by 802.11 standards
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unspecified(1), previousAuthNotValid(2), deauthenticationLeaving(3), disassociationDueToInactivity(4), disassociationAPBusy(5), class2FrameFromNonAuthStation(6), class2FrameFromNonAssStation(7), disassociationStaHasLeft(8), staReqAssociationWithoutAuth(9), invalidInformationElement(40), groupCipherInvalid(41), unicastCipherInvalid(42), akmpInvalid(43), unsupportedRsnVersion(44), invalidRsnIeCapabilities(45), cipherSuiteRejected(46), missingReasonCode(99)  

bsnMobileStationMobilityStatus 1.3.6.1.4.1.14179.2.1.4.1.11
Mobility Role of the Mobile Station.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unassociated(0), local(1), anchor(2), foreign(3), handoff(4), unknown(5), exportanchor(6), exportforeign(7)  

bsnMobileStationAnchorAddress 1.3.6.1.4.1.14179.2.1.4.1.12
If the Mobility Status of the Mobile Station is Anchor then it will have Peer Ip Address and will have Anchor IP if the Role is Foreign
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bsnMobileStationCFPollable 1.3.6.1.4.1.14179.2.1.4.1.13
When this attribute is true, it shall indicate that the Mobile Station is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the Mobile Station is not able to respond to a CF-Poll with a data frame within a SIFS time.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnMobileStationCFPollRequest 1.3.6.1.4.1.14179.2.1.4.1.14
Specifies whether CFP is requested by Mobile Station or not
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnMobileStationChannelAgilityEnabled 1.3.6.1.4.1.14179.2.1.4.1.15
This attribute indicates that the PHY channel agility functionality is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnMobileStationPBCCOptionImplemented 1.3.6.1.4.1.14179.2.1.4.1.16
This attribute, when true, shall indicate that the PBCC modulation option as defined in subclause 18.4.6.6 is implemented. The default value of this attribute shall be false.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnMobileStationShortPreambleOptionImplemented 1.3.6.1.4.1.14179.2.1.4.1.17
This attribute, when true, shall indicate that the short preamble option as defined in subclause 18.2.2.2 is implemented. The default value of this attribute shall be false.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnMobileStationSessionTimeout 1.3.6.1.4.1.14179.2.1.4.1.18
Session Timeout of Mobile station
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnMobileStationAuthenticationAlgorithm 1.3.6.1.4.1.14179.2.1.4.1.19
Authentication Algorithm of Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER openSystem(0), sharedKey(1), unknown(2), openAndEap(128)  

bsnMobileStationWepState 1.3.6.1.4.1.14179.2.1.4.1.20
WEP State of Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

bsnMobileStationPortNumber 1.3.6.1.4.1.14179.2.1.4.1.21
The Port Number of this Airespace Switch on which the traffic of the Mobile Station is coming through.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnMobileStationDeleteAction 1.3.6.1.4.1.14179.2.1.4.1.22
Action to Deauthenticate the Mobile Station. Set the State to delete.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), delete(1)  

bsnMobileStationPolicyManagerState 1.3.6.1.4.1.14179.2.1.4.1.23
Policy Manager State of the mobile station.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnMobileStationSecurityPolicyStatus 1.3.6.1.4.1.14179.2.1.4.1.24
When this attribute has value completed, it shall indicate that the Mobile Station has completed the security policy checks. Otherwise the checks are yet to be completed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER completed(0), notcompleted(1)  

bsnMobileStationProtocol 1.3.6.1.4.1.14179.2.1.4.1.25
The 802.11 protocol type of the client. The protocol is mobile when this client detail is seen on the anchor i.e it's mobility status is anchor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot11a(1), dot11b(2), dot11g(3), unknown(4), mobile(5), dot11n24(6), dot11n5(7)  

bsnMobileStationMirrorMode 1.3.6.1.4.1.14179.2.1.4.1.26
If enabled, then mirroring for this client will be statically configured irrespective of the AP and the port this client is on.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnMobileStationInterface 1.3.6.1.4.1.14179.2.1.4.1.27
Name of the Interface of the mobile client to the switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

bsnMobileStationApMode 1.3.6.1.4.1.14179.2.1.4.1.28
Mode of the AP to which the Mobile Station is associated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local(0), monitor(1), remote(2), roguedetector(3)  

bsnMobileStationVlanId 1.3.6.1.4.1.14179.2.1.4.1.29
Vlan ID of the Interface to which the client is associated.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4096  

bsnMobileStationPolicyType 1.3.6.1.4.1.14179.2.1.4.1.30
Mode of the AP to which the Mobile Station is associated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot1x(0), wpa1(1), wpa2(2), wpa2vff(3), notavailable(4), unknown(5)  

bsnMobileStationEncryptionCypher 1.3.6.1.4.1.14179.2.1.4.1.31
Mode of the AP to which the Mobile Station is associated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ccmpAes(0), tkipMic(1), wep40(2), wep104(3), wep128(4), none(5), notavailable(6), unknown(7)  

bsnMobileStationEapType 1.3.6.1.4.1.14179.2.1.4.1.32
Mode of the AP to which the Mobile Station is associated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER eapTls(0), ttls(1), peap(2), leap(3), speke(4), eapFast(5), notavailable(6), unknown(7)  

bsnMobileStationCcxVersion 1.3.6.1.4.1.14179.2.1.4.1.33
Represents the Cisco Compatible Extensions (CCX) Version the client is using for communication with the AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(0), ccxv1(1), ccxv2(2), ccxv3(3), ccxv4(4), ccxv5(5)  

bsnMobileStationE2eVersion 1.3.6.1.4.1.14179.2.1.4.1.34
Represents the End-2-End Version the client is using for communication with the AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(0), e2ev1(1), e2ev2(2)  

bsnMobileStationStatusCode 1.3.6.1.4.1.14179.2.1.4.1.42
Status Code of the Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bsnMobileStationByIpTable 1.3.6.1.4.1.14179.2.1.10
Mobile Station Table indexed by bsnMobileStationByIpAddress. NOTE: This is just to facilitate the search of mobile stations based on IP Address. Doing a get without the index doesn't return anything. (Mobile Station is better referred to as Client in the current releases.)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationByIpEntry

bsnMobileStationByIpEntry 1.3.6.1.4.1.14179.2.1.10.1
An entry in bsnMobileStationByIpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMobileStationByIpEntry  

bsnMobileStationByIpAddress 1.3.6.1.4.1.14179.2.1.10.1.1
IP Address of the Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bsnMobileStationByIpMacAddress 1.3.6.1.4.1.14179.2.1.10.1.2
802.11 Mac Address of the Mobile Station.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnMobileStationByUsernameTable 1.3.6.1.4.1.14179.2.1.13
Mobile Station Table indexed by the Mobile Station Username and MAC Address. NOTE: This is just to facilitate the search of mobile stations based on User Name. Doing a get without the username doesn't return anything. (Mobile Station is better referred to as Client in the current releases.)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationByUsernameEntry

bsnMobileStationByUsernameEntry 1.3.6.1.4.1.14179.2.1.13.1
An entry in bsnMobileStationByUsernameTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMobileStationByUsernameEntry  

bsnMobileStationByUserName 1.3.6.1.4.1.14179.2.1.13.1.1
Username of the Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..64)  

bsnMobileStationByUserMacAddress 1.3.6.1.4.1.14179.2.1.13.1.2
802.11 Mac Address of the Mobile Station.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnMobileStationPerRadioPerVapTable 1.3.6.1.4.1.14179.2.1.5
Mobile Station Per Radio Per VAP(WLAN) Table. This table lists all Mobile Stations on a particular Airespace AP Interface for a particular ESS(Wlan). It only lists MAC Addresses. Further details for a Mobile Station can be found from bsnMobileStationTable once the MAC Address is knonwn. (Mobile Station is better referred to as Client in the current releases.)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationPerRadioPerVapEntry

bsnMobileStationPerRadioPerVapEntry 1.3.6.1.4.1.14179.2.1.5.1
An entry in MobileStationPerRadioPerVapTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMobileStationPerRadioPerVapEntry  

bsnMobileStationPerRadioPerVapIndex 1.3.6.1.4.1.14179.2.1.5.1.1
The index of Mobile Station. The index starts from 1 and goes upto the total number of Mobile Stations on Airespace Radio Interface for a specific ESS (Wlan).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMobileStationMacAddr 1.3.6.1.4.1.14179.2.1.5.1.20
The MAC Address of Mobile Station.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnMobileStationStatsTable 1.3.6.1.4.1.14179.2.1.6
Mobile Station Statistics Table. (Mobile Station is better referred to as Client in the current releases.)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationStatsEntry

bsnMobileStationStatsEntry 1.3.6.1.4.1.14179.2.1.6.1
An entry in bsnMobileStationStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMobileStationStatsEntry  

bsnMobileStationRSSI 1.3.6.1.4.1.14179.2.1.6.1.1
Average packet RSSI for the Mobile Station.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMobileStationBytesReceived 1.3.6.1.4.1.14179.2.1.6.1.2
Bytes received from Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bsnMobileStationBytesSent 1.3.6.1.4.1.14179.2.1.6.1.3
Bytes sent to Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bsnMobileStationPolicyErrors 1.3.6.1.4.1.14179.2.1.6.1.4
Number of Policy Errors for Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bsnMobileStationPacketsReceived 1.3.6.1.4.1.14179.2.1.6.1.5
Packets received from Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bsnMobileStationPacketsSent 1.3.6.1.4.1.14179.2.1.6.1.6
Packets sent to Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bsnMobileStationSnr 1.3.6.1.4.1.14179.2.1.6.1.26
Signal to noise Ratio of the Mobile Station.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMobileStationExtStatsTable 1.3.6.1.4.1.14179.2.1.21
This table was supported only by indoor mesh AP -cisco 1000. As this AP is not supported after 4.2.x.x. This table has been marked obsolete. Mobile Station Extended Statistics Table. (Mobile Station is better referred to as Client in the current releases.)
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationExtStatsEntry

bsnMobileStationExtStatsEntry 1.3.6.1.4.1.14179.2.1.21.1
An entry in bsnMobileStationExtStatsTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  BsnMobileStationExtStatsEntry  

bsnMobileStationSampleTime 1.3.6.1.4.1.14179.2.1.21.1.1
Time stats were sampled as seconds since the epoch.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMobileStationTxExcessiveRetries 1.3.6.1.4.1.14179.2.1.21.1.2
Tx packets dropped due to excessive retries.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

bsnMobileStationTxRetries 1.3.6.1.4.1.14179.2.1.21.1.3
Tx packets retransmitted.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

bsnMobileStationTxFiltered 1.3.6.1.4.1.14179.2.1.21.1.20
Tx packets dropped by the built-in Tx filter
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

bsnMobileStationRssiDataTable 1.3.6.1.4.1.14179.2.1.11
Mobile Station RSSI data Table indexed by bsnMobileStationMacAddress, bsnMobileStationRssiDataApMacAddress, bsnMobileStationRssiDataApIfSlotId. (Mobile Station is better referred to as Client in the current releases.)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationRssiDataEntry

bsnMobileStationRssiDataEntry 1.3.6.1.4.1.14179.2.1.11.1
An entry in bsnMobileStationRssiDataTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMobileStationRssiDataEntry  

bsnMobileStationRssiDataApMacAddress 1.3.6.1.4.1.14179.2.1.11.1.1
802.11 Mac Address of the AP on which Mobile Station is associated.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnMobileStationRssiDataApIfSlotId 1.3.6.1.4.1.14179.2.1.11.1.2
SlotId of APIf on which mobile station is associated
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..15  

bsnMobileStationRssiDataApIfType 1.3.6.1.4.1.14179.2.1.11.1.3
The interface type of the radio that sensed the rssi data.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot11bg(1), dot11a(2), unknown(3)  

bsnMobileStationRssiDataApName 1.3.6.1.4.1.14179.2.1.11.1.4
The Name of the AP that sensed the rssi data.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnMobileStationRssiData 1.3.6.1.4.1.14179.2.1.11.1.5
RSSI seen by Airespace AP Interface for the Mobile Station
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfPhyAntennaIndex 1.3.6.1.4.1.14179.2.1.11.1.6
Antenna which recived the probe request from client. The antenna which reported the RSSI value for the client. For now value will be 0 to 1, in future it may change.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnMobileStationRssiDataLastHeard 1.3.6.1.4.1.14179.2.1.11.1.25
No of seconds ago when this RSSI data was recorded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTagTable 1.3.6.1.4.1.14179.2.1.18
RF ID Tag Table indexed by bsnTagDot11MacAddress.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnTagEntry

bsnTagEntry 1.3.6.1.4.1.14179.2.1.18.1
An entry in bsnTagTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnTagEntry  

bsnTagDot11MacAddress 1.3.6.1.4.1.14179.2.1.18.1.1
802.11 MAC Address of the RF ID Tag.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnTagType 1.3.6.1.4.1.14179.2.1.18.1.2
Type of the RF ID Tag.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), type1(2)  

bsnTagTimeInterval 1.3.6.1.4.1.14179.2.1.18.1.3
Time Interval after which the tag transmits data.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnTagBatteryStatus 1.3.6.1.4.1.14179.2.1.18.1.4
Battery Status of the RF ID Tag.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), low(1), normal(2), medium(3)  

bsnTagLastReported 1.3.6.1.4.1.14179.2.1.18.1.23
No of seconds ago when this tag was heard by any AP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnTagStatsTable 1.3.6.1.4.1.14179.2.1.20
RF ID Tag Statistics Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnTagStatsEntry

bsnTagStatsEntry 1.3.6.1.4.1.14179.2.1.20.1
An entry in bsnTagStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnTagStatsEntry  

bsnTagBytesReceived 1.3.6.1.4.1.14179.2.1.20.1.1
Bytes received from an RF ID Tag
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnTagPacketsReceived 1.3.6.1.4.1.14179.2.1.20.1.20
Packets received from an RF ID Tag
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnTagRssiDataTable 1.3.6.1.4.1.14179.2.1.19
RF ID Tag Detecting AP Table indexed by bsnTagDot11MacAddress, bsnTagRssiDataApMacAddress and bsnTagRssiDataApIfSlotId.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnTagRssiDataEntry

bsnTagRssiDataEntry 1.3.6.1.4.1.14179.2.1.19.1
An entry in bsnTagRssiDataTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnTagRssiDataEntry  

bsnTagRssiDataApMacAddress 1.3.6.1.4.1.14179.2.1.19.1.1
802.11 MAC Address of the AP detecting the RF ID Tag.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnTagRssiDataApIfSlotId 1.3.6.1.4.1.14179.2.1.19.1.2
Slot Id of the radio on AP detecting the RF ID Tag.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5  

bsnTagRssiDataApIfType 1.3.6.1.4.1.14179.2.1.19.1.3
Interface Type of the radio on AP detecting the RF ID Tag.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2), uwb(4)  

bsnTagRssiDataApName 1.3.6.1.4.1.14179.2.1.19.1.4
Name of the AP detecting the RF ID Tag.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

bsnTagRssiDataLastHeard 1.3.6.1.4.1.14179.2.1.19.1.5
No of seconds ago when this tag was heard by this detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTagRssiData 1.3.6.1.4.1.14179.2.1.19.1.6
RSSI of the RF ID Tag as seen by the radio on this detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnTagRssiDataSnr 1.3.6.1.4.1.14179.2.1.19.1.26
SNR of the RF ID tag as seen by the radio on this detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnWatchListClientTable 1.3.6.1.4.1.14179.2.1.12
Table of watch listed clients. When clients are added to this table by username or MAC address, ACS collects data for them to show trend reports. The switch generates Client Association and Client Authentication traps for the watch listed clients.The watch list feature can be enbaled or diabled by the bsnWatchListFeatureEnable flag on the switch.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnWatchListClientEntry

bsnWatchListClientEntry 1.3.6.1.4.1.14179.2.1.12.1
An entry in bsnWatchListClientTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  BsnWatchListClientEntry  

bsnWatchListClientKey 1.3.6.1.4.1.14179.2.1.12.1.1
MAC Address or User Name of Client that is to be added to the watch list.
Status: obsolete Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..64)  

bsnWatchListClientType 1.3.6.1.4.1.14179.2.1.12.1.2
The type of the watch list client entry. The entry can be created by Client MAC Address or by Username.
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER byMac(1), byUserName(2)  

bsnWatchListClientRowStatus 1.3.6.1.4.1.14179.2.1.12.1.20
A row status type for the bsnWatchListClientEntry
Status: obsolete Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnRogueAPTable 1.3.6.1.4.1.14179.2.1.7
Rogue Table. This table lists all the Rogue APs detected by Airespace APs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRogueAPEntry

bsnRogueAPEntry 1.3.6.1.4.1.14179.2.1.7.1
An Entry in bsnRogueAPTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnRogueAPEntry  

bsnRogueAPDot11MacAddress 1.3.6.1.4.1.14179.2.1.7.1.1
MAC Address of Rogue Station.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

bsnRogueAPTotalDetectingAPs 1.3.6.1.4.1.14179.2.1.7.1.2
Total number of Airespace APs that detected this rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueAPFirstReported 1.3.6.1.4.1.14179.2.1.7.1.3
Time Stamp when this Rogue was First Detected.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnRogueAPLastReported 1.3.6.1.4.1.14179.2.1.7.1.4
Time Stamp when this Rogue was Last Detected.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnRogueAPContainmentLevel 1.3.6.1.4.1.14179.2.1.7.1.5
If the state of the rogue is contained, this specifies the level of containment. Higher the level, more the number of detecting APs that are used to contain it. The value must be between 1 to 4 for 'contained' state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER unassigned(0), level1(1), level2(2), level3(3), level4(4)  

bsnRogueAPType 1.3.6.1.4.1.14179.2.1.7.1.6
This attribute specifies if the Rogue is of ad-hoc type or is an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ap(0), adhoc(1)  

bsnRogueAPOnNetwork 1.3.6.1.4.1.14179.2.1.7.1.7
This attribute specifies if the Rogue is on Wired Network or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnRogueAPTotalClients 1.3.6.1.4.1.14179.2.1.7.1.8
Total number of Clients detected on this rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueAPRowStatus 1.3.6.1.4.1.14179.2.1.7.1.9
Row Status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnRogueAPMaxDetectedRSSI 1.3.6.1.4.1.14179.2.1.7.1.10
This is the max RSSI value of all the detctecting APs, which have detected this rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueAPSSID 1.3.6.1.4.1.14179.2.1.7.1.11
This is the SSID of the rogue detected by Access Point, which has max RSSI value of all the detectecting APs of this rogue.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

bsnRogueAPDetectingAPRadioType 1.3.6.1.4.1.14179.2.1.7.1.12
Radio type of detecting APs. If the radio type is detected by dot11bg radio or dot11a radio or both.
Status: current Access: read-only
OBJECT-TYPE    
  BITS dot11b(0), dot11a(1), dot11g(2), dot11n24(3), dot11n5(4)  

bsnRogueAPDetectingAPMacAddress 1.3.6.1.4.1.14179.2.1.7.1.13
MAC Address of of detecting AP which received max RSSI
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnRogueAPMaxRssiRadioType 1.3.6.1.4.1.14179.2.1.7.1.14
The radio type of detecting AP which received max RSSI value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2), uwb(4), dot11g(5), dot11n24(6), dot11n5(7)  

bsnRogueAPState 1.3.6.1.4.1.14179.2.1.7.1.24
This attribute is use to specify the state in which the Rogue AP is user can set the Rogue AP in alert, known or acknowledge state. Alert state means Rogue AP can be a potential threat. Trap will be sent out to trap recipients. Known state means its just internal AP which is not on the same Switch. Acknowledge state means an external AP whose existence is acceptable and not a threat (probably some other company's AP). Contained means containement is initiated and ongoing. Threat is usually the state when the rogue is found on wired network. known(4), knownContained(9) and trustedMissing(10) will appear in known rogue list. known rogues can be pre provisioned and known rogues state can be changed to alert(2)
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER initializing(0), pending(1), alert(2), detectedLrad(3), known(4), acknowledge(5), contained(6), threat(7), containedPending(8), knownContained(9), trustedMissing(10)  

bsnRogueAPClassType 1.3.6.1.4.1.14179.2.1.7.1.25
The AP class type of the client detected.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER pending(0), friendly(1), malicious(2), unclassified(3)  

bsnRogueAPChannel 1.3.6.1.4.1.14179.2.1.7.1.26
This is the channel number of the last detecting APs, which has detected this rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueAPDetectingAPName 1.3.6.1.4.1.14179.2.1.7.1.27
AP name of the detecting AP which received max RSSI
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnRogueAPAirespaceAPTable 1.3.6.1.4.1.14179.2.1.8
Rogue Station Table. This table lists all the Airespace AP Interfaces that detected a particular Rogue.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRogueAPAirespaceAPEntry

bsnRogueAPAirespaceAPEntry 1.3.6.1.4.1.14179.2.1.8.1
An entry in bsnRogueAPAirespaceAPEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnRogueAPAirespaceAPEntry  

bsnRogueAPAirespaceAPMacAddress 1.3.6.1.4.1.14179.2.1.8.1.1
MAC Address of Airespace AP Interface that Detected the Rogue.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnRogueAPAirespaceAPSlotId 1.3.6.1.4.1.14179.2.1.8.1.2
The slot ID of the Airespace AP Interface that detected the Rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..2  

bsnRogueAPRadioType 1.3.6.1.4.1.14179.2.1.8.1.3
The Airespace AP Interface type that detected the Rogue.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2), unknown(3), uwb(4), dot11g(5), dot11n24(6), dot11n5(7)  

bsnRogueAPAirespaceAPName 1.3.6.1.4.1.14179.2.1.8.1.4
Name of Airespace AP Interface that detected the Rogue.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnRogueAPChannelNumber 1.3.6.1.4.1.14179.2.1.8.1.5
The advertised Channel Number of the Airespace AP Interface picked up from the Rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueAPSsid 1.3.6.1.4.1.14179.2.1.8.1.6
The SSID Advertised by Rogue Station.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnRogueAPAirespaceAPRSSI 1.3.6.1.4.1.14179.2.1.8.1.7
Rogue RSSI as seen by Airespace AP Interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueAPContainmentMode 1.3.6.1.4.1.14179.2.1.8.1.8
If the rogue is in 'contained' state, this attribute shows the containment mode used by the AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(0), deauthBroadcast(1), cfp(2), max(3), unknown(99)  

bsnRogueAPContainmentChannelCount 1.3.6.1.4.1.14179.2.1.8.1.9
The number of channels used for rogue containment.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnRogueAPContainmentChannels 1.3.6.1.4.1.14179.2.1.8.1.10
This is the comma separated string of channels used for rogue containment.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnRogueAPAirespaceAPLastHeard 1.3.6.1.4.1.14179.2.1.8.1.11
No of seconds ago when this Rogue was last heard by this AP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRogueAPAirespaceAPWepMode 1.3.6.1.4.1.14179.2.1.8.1.12
The WEP mode on this detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bsnRogueAPAirespaceAPPreamble 1.3.6.1.4.1.14179.2.1.8.1.13
The Preamble on this detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER long(0), short(1), notSupported(2)  

bsnRogueAPAirespaceAPWpaMode 1.3.6.1.4.1.14179.2.1.8.1.14
The WPA mode on this detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bsnRogueAPAirespaceAPSNR 1.3.6.1.4.1.14179.2.1.8.1.27
SNR seen by Airespace AP Interface from Rogue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueAPChannelWidth 1.3.6.1.4.1.14179.2.1.8.1.28
This object represents the channel width of the rogue.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER five(1), ten(2), twenty(3), aboveforty(4), belowforty(5)  

bsnRogueClientPerRogueAPTable 1.3.6.1.4.1.14179.2.1.16
Rogue Clients for each rogue. This table lists all Rogue Clients on a particular Rogue.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRogueClientPerRogueAPEntry

bsnRogueClientPerRogueAPEntry 1.3.6.1.4.1.14179.2.1.16.1
An entry in RogueClientPerRogueAPTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnRogueClientPerRogueAPEntry  

bsnRogueAPDot11MacAddr 1.3.6.1.4.1.14179.2.1.16.1.1
The MAC Address of the Rogue AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnRogueClientDot11MacAddr 1.3.6.1.4.1.14179.2.1.16.1.20
MAC Address of the Rogue Client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnRogueClientTable 1.3.6.1.4.1.14179.2.1.14
Rogue Client Table. This table lists all the Rogue Clients detected by Airespace APs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRogueClientEntry

bsnRogueClientEntry 1.3.6.1.4.1.14179.2.1.14.1
An Entry in bsnRogueClientTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnRogueClientEntry  

bsnRogueClientDot11MacAddress 1.3.6.1.4.1.14179.2.1.14.1.1
Mac Address of Rogue Station.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

bsnRogueClientTotalDetectingAPs 1.3.6.1.4.1.14179.2.1.14.1.2
Total number of Airespace APs that detected this rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueClientFirstReported 1.3.6.1.4.1.14179.2.1.14.1.3
Time Stamp when this Rogue was First Detected.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnRogueClientLastReported 1.3.6.1.4.1.14179.2.1.14.1.4
Time Stamp when this Rogue was Last Detected.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnRogueClientBSSID 1.3.6.1.4.1.14179.2.1.14.1.5
This attribute specifies BSSID of the Rogue Client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnRogueClientContainmentLevel 1.3.6.1.4.1.14179.2.1.14.1.6
If the state of the rogue is contained, this specifies the level of containment. Higher the level, more the number of detecting APs that are used to contain it. The value must be between 1 to 4 for 'contained' state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unassigned(0), level1(1), level2(2), level3(3), level4(4)  

bsnRogueClientLastHeard 1.3.6.1.4.1.14179.2.1.14.1.7
Number of seconds ago this rogue client was detected.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueClientState 1.3.6.1.4.1.14179.2.1.14.1.24
This attribute is use to specify the state in which the Rogue AP is. User can set the Rogue Client in alert,known or acknowledge state. Alert state means Rogue Client can be a potential i threat.Trap will be sent out to trap recipients. Known state means its just internal Client which is not on the same Switch. Acknowledge state means an external Client whose existence is acceptable and not a threat (probably some other company's AP). Contained means containement is initiated and ongoing
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER initializing(0), pending(1), alert(2), contained(6), threat(7), containedpending(8)  

bsnRogueClientAirespaceAPTable 1.3.6.1.4.1.14179.2.1.15
Rogue Station Table. This table lists all the Airespace AP Interface that detected a particular Rogue.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRogueClientAirespaceAPEntry

bsnRogueClientAirespaceAPEntry 1.3.6.1.4.1.14179.2.1.15.1
An entry in bsnRogueClientAirespaceAPEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnRogueClientAirespaceAPEntry  

bsnRogueClientAirespaceAPMacAddress 1.3.6.1.4.1.14179.2.1.15.1.1
Mac Address of Airespace AP Interface that Detected the Rogue.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnRogueClientAirespaceAPSlotId 1.3.6.1.4.1.14179.2.1.15.1.2
The slotId of the Airespace AP Interface that detected the Rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..2  

bsnRogueClientRadioType 1.3.6.1.4.1.14179.2.1.15.1.3
The advertised SSID that the Airespace AP Interface picked up from the Rogue.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2), unknown(3)  

bsnRogueClientAirespaceAPName 1.3.6.1.4.1.14179.2.1.15.1.4
Name of Airespace AP Interface that detected the Rogue.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnRogueClientChannelNumber 1.3.6.1.4.1.14179.2.1.15.1.5
The advertised Channel Number of that the Airespace AP Interface picked up from the Rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueClientAirespaceAPRSSI 1.3.6.1.4.1.14179.2.1.15.1.7
RSSI seen by Airespace AP Interface from the Rogue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnRogueClientAirespaceAPLastHeard 1.3.6.1.4.1.14179.2.1.15.1.11
No of seconds ago when this Rogue was last heard by this AP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnRogueClientAirespaceAPSNR 1.3.6.1.4.1.14179.2.1.15.1.27
SNR seen by Airespace AP Interface from Rogue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnThirdPartyAPTable 1.3.6.1.4.1.14179.2.1.9
Third Party Access Point Table. An entry needs to be configured in this table for a third party access point that needs to be supported by the Switch. Note: A third party ESS (Wlan) with ID 17 should be created in bsnDot11EssTable before adding entries here. Please also note that ACS currently supports only Aironet 350, 1200 and Orinoco 2000 Access Points as third party APs.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnThirdPartyAPEntry

bsnThirdPartyAPEntry 1.3.6.1.4.1.14179.2.1.9.1
An entry in bsnThirdPartyAPTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  BsnThirdPartyAPEntry  

bsnThirdPartyAPMacAddress 1.3.6.1.4.1.14179.2.1.9.1.1
MAC Address of Third Party Access Point which is connected directly to this Airespace Switch.
Status: obsolete Access: read-create
OBJECT-TYPE    
  MacAddress  

bsnThirdPartyAPInterface 1.3.6.1.4.1.14179.2.1.9.1.2
Interface(Port Number) to which the Third Party AP is connected.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32  

bsnThirdPartyAPIpAddress 1.3.6.1.4.1.14179.2.1.9.1.3
Static IP address of the 3rd Party AP, 0.0.0.0 indicating x its using DHCP
Status: obsolete Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnThirdPartyAP802Dot1XRequired 1.3.6.1.4.1.14179.2.1.9.1.4
If 802.1X is required for the 3rd Party AP
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnThirdPartyAPMirrorMode 1.3.6.1.4.1.14179.2.1.9.1.5
If enabled, then data from all the foreign AP users and all the foreign APs on this APs port will be mirrored. These clients are dynamically added to the switch's mirrored MAC list.
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnThirdPartyAPRowStatus 1.3.6.1.4.1.14179.2.1.9.1.24
Row Status in the ThirdPartyAPEntry.
Status: obsolete Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnAPTable 1.3.6.1.4.1.14179.2.2.1
Table of Airespace APs managed by this Airespace Switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPEntry

bsnAPEntry 1.3.6.1.4.1.14179.2.2.1.1
An entry in the bsnAPTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPEntry  

bsnAPDot3MacAddress 1.3.6.1.4.1.14179.2.2.1.1.1
The MAC address of an AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnAPNumOfSlots 1.3.6.1.4.1.14179.2.2.1.1.2
Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..24  

bsnAPName 1.3.6.1.4.1.14179.2.2.1.1.3
Name assigned to this AP. If an AP is not configured its factory default name will be ap: eg. ap:af:12:be
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnAPLocation 1.3.6.1.4.1.14179.2.2.1.1.4
User specified location of this AP. While configuring AP, user should specify a location for the AP so that its easy to figure out for some one where the AP is located.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..80)  

bsnAPMonitorOnlyMode 1.3.6.1.4.1.14179.2.2.1.1.5
Monitor Only Mode Setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER local(0), monitor(1), remote(2), roguedetector(3), sniffer(4), bridge(5), seConnect(6)  

bsnAPOperationStatus 1.3.6.1.4.1.14179.2.2.1.1.6
Operation State of the AP. When AP associates with the Airespace Switch its state will be associated. When Airespace AP is disassociated from the Switch, its state will be disassociating. The state is downloading when the AP is downloading its firmware.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER associated(1), disassociating(2), downloading(3)  

bsnAPSoftwareVersion 1.3.6.1.4.1.14179.2.2.1.1.8
Major Minor Software Version of AP
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnAPBootVersion 1.3.6.1.4.1.14179.2.2.1.1.9
Major Minor Boot Version of AP
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnAPPrimaryMwarName 1.3.6.1.4.1.14179.2.2.1.1.10
sysName of the Airespace Switch which is suppose to be the Primary MWAR(switch) of the AP with which AP should associate. This work when AP is not directly connected to Airespace Switch, it tries to find Primary Switch and associates with it. If this attribute is left empty or AP is not able to find the Airespace Switch with this name, then it will associate with Secondary Switch.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

bsnAPReset 1.3.6.1.4.1.14179.2.2.1.1.11
Set this attribute to reset the AP. When it comes up it will try to associate with the Primary Switch if that is set, else it will associate with the Master Switch. Reading this attribute will always return 0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), default(0)  

bsnAPStatsTimer 1.3.6.1.4.1.14179.2.2.1.1.12
Configures the time interval in secs after which bsnAPDot11Counters Stats is sent from AP to Switch. If not configured this value is 0 which means never send the stats.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

bsnAPPortNumber 1.3.6.1.4.1.14179.2.2.1.1.13
Port on the Switch on which this APs traffic is coming through.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bsnAPModel 1.3.6.1.4.1.14179.2.2.1.1.16
AP Model
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnAPSerialNumber 1.3.6.1.4.1.14179.2.2.1.1.17
AP Serial Number.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnAPClearConfig 1.3.6.1.4.1.14179.2.2.1.1.18
Set this attribute to clear AP configuration and reset it to factory defaults. Reading this attribute will always return 0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clear(1), default(0)  

bsnApIpAddress 1.3.6.1.4.1.14179.2.2.1.1.19
IP address of the AP. This will not be available when the switch is operating in the Layer2 mode. In this case, the attribute will return 0 as value.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

bsnAPMirrorMode 1.3.6.1.4.1.14179.2.2.1.1.20
If enabled, then this AP's Client's Data is mirrored and this AP's clients are dynamically added to the switch's mirrored MAC list.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPRemoteModeSupport 1.3.6.1.4.1.14179.2.2.1.1.21
This specifies if the the Remote Mode is supported on this AP or not. If supported user can set bsnAPMonitorOnlyMode to remote. Otherwise not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPType 1.3.6.1.4.1.14179.2.2.1.1.22
This is the model of the AP in enumeration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ap1000(1), ap1030(2), mimo(3), unknown(4), ap1100(5), ap1130(6), ap1240(7), ap1200(8), ap1310(9), ap1500(10), ap1250(11), ap1505(12), ap3201(13), ap1520(14), ap800(15), ap1140(16), ap800agn(17), ap3500i(18), ap3500e(19), ap1260(20)  

bsnAPSecondaryMwarName 1.3.6.1.4.1.14179.2.2.1.1.23
sysName of the Airespace Switch which is suppose to be the Secondary MWAR(switch) of the AP with which AP should associate if Primary Switch(configured through bsnAPPrimaryMwarName) is not available. If primary and secondary switches are not available then AP will associate with the tertiary switch.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

bsnAPTertiaryMwarName 1.3.6.1.4.1.14179.2.2.1.1.24
sysName of the Airespace Switch which is suppose to be the Tertiary MWAR(switch) of the AP with which AP should associate. If primary,secondary and tertiary switch are not available then it will associate with Master Switch.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

bsnAPIsStaticIP 1.3.6.1.4.1.14179.2.2.1.1.25
This flag when disabled implies that AP will use DHCP to get the IP address. However, if it is enabled, then user should enter the IPAddress, Netmask and Gateway.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPNetmask 1.3.6.1.4.1.14179.2.2.1.1.26
The Netmask of the IP address of the AP.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

bsnAPGateway 1.3.6.1.4.1.14179.2.2.1.1.27
The Gateway for the AP.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

bsnAPStaticIPAddress 1.3.6.1.4.1.14179.2.2.1.1.28
The Static IP-Address configuration for the AP. This can only be changed when the LWAPP mode is in Layer-3.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

bsnAPBridgingSupport 1.3.6.1.4.1.14179.2.2.1.1.29
This specifies if this AP is a Bridging AP. Bridging APs can be used in Bridging or Mesh network configurations.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPGroupVlanName 1.3.6.1.4.1.14179.2.2.1.1.30
The AP Group to which this AP has been associated with. If it is empty, then no AP Group overriding has been set.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnAPIOSVersion 1.3.6.1.4.1.14179.2.2.1.1.31
IOS Version of IOS Cisco AP. Zero length string will be returned for other APs
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnAPCertificateType 1.3.6.1.4.1.14179.2.2.1.1.32
Enum values denoting AP Certificate Type. 1 : manufactureinstalled : Manufacture Installed Certificate type (MIC). 2 : selfsigned : Self Signed Certificate type (SSC). 3 : localsignificance : Local Significance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), manufactureinstalled(1), selfsigned(2), localsignificance(3)  

bsnAPEthernetMacAddress 1.3.6.1.4.1.14179.2.2.1.1.33
The Ethernet MAC address of the AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnAPAdminStatus 1.3.6.1.4.1.14179.2.2.1.1.37
Admin State of the AP
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

bsnAPIfTable 1.3.6.1.4.1.14179.2.2.2
Each entry represents an 802.11 interface in an Airespace AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfEntry

bsnAPIfEntry 1.3.6.1.4.1.14179.2.2.2.1
An entry in bsnAPIfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfEntry  

bsnAPIfSlotId 1.3.6.1.4.1.14179.2.2.2.1.1
The slotId of this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..2  

bsnAPIfType 1.3.6.1.4.1.14179.2.2.2.1.2
The type of this interface. dot11b also implies 802.11b/g.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2), uwb(4)  

bsnAPIfPhyChannelAssignment 1.3.6.1.4.1.14179.2.2.2.1.3
If this value is true, then bsnAPDot11CurrentChannel in bsnAPIfDot11PhyDSSSTable is assigned by dynamic algorithm and is read-only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER automatic(1), customized(2)  

bsnAPIfPhyChannelNumber 1.3.6.1.4.1.14179.2.2.2.1.4
Current channel number of the AP Interface. Channel numbers will be from 1 to 14 for 802.11b interface type. Channel numbers will be from 34 to 169 for 802.11a interface type. Allowed channel numbers also depends on the current Country Code set in the Switch. This attribute cannot be set unless bsnAPIfPhyChannelAssignment is set to customized else this attribute gets assigned by dynamic algorithm.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ch1(1), ch2(2), ch3(3), ch4(4), ch5(5), ch6(6), ch7(7), ch8(8), ch9(9), ch10(10), ch11(11), ch12(12), ch13(13), ch14(14), ch20(20), ch21(21), ch22(22), ch23(23), ch24(24), ch25(25), ch26(26), ch34(34), ch36(36), ch38(38), ch40(40), ch42(42), ch44(44), ch46(46), ch48(48), ch52(52), ch56(56), ch60(60), ch64(64), ch100(100), ch104(104), ch108(108), ch112(112), ch116(116), ch120(120), ch124(124), ch128(128), ch132(132), ch136(136), ch140(140), ch149(149), ch153(153), ch157(157), ch161(161), ch165(165), ch169(169)  

bsnAPIfPhyTxPowerControl 1.3.6.1.4.1.14179.2.2.2.1.5
If this value is true, then bsnAPIfPhyTxPowerLevel is assigned by dynamic algorithm and is read-only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER automatic(1), customized(2)  

bsnAPIfPhyTxPowerLevel 1.3.6.1.4.1.14179.2.2.2.1.6
The TxPowerLevel currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA. Valid values are between 1 to 8,depnding on what radio, and this attribute can be set only if bsnAPIfPhyTxPowerControl is set to customized.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..8  

bsnAPIfPhyAntennaMode 1.3.6.1.4.1.14179.2.2.2.1.7
Antenna Mode of the AP Interface. For 802.11a this attribute will always be omni for now. This attribute doesn't apply to interface of type 802.11b.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER sectorA(1), sectorB(2), omni(3), notapplicable(99)  

bsnAPIfPhyAntennaType 1.3.6.1.4.1.14179.2.2.2.1.8
This attribute specified if the Antenna currently used by AP Radio is internal or external. For 802.11a the antenna is always internal. For 802.11b you can set antenna type to be external or internal.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

bsnAPIfPhyAntennaDiversity 1.3.6.1.4.1.14179.2.2.2.1.9
Diversity doesn't apply to AP Radio of type 802.11a. For 802.11b you can set it to connectorA, connectorB or enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER connectorA(0), connectorB(1), enabled(255)  

bsnAPIfCellSiteConfigId 1.3.6.1.4.1.14179.2.2.2.1.10
In a cell site configuration, this would be the cell Id of this AP Interface
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnAPIfNumberOfVaps 1.3.6.1.4.1.14179.2.2.2.1.11
Number of WLANs currently active on this AP Interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

bsnAPIfOperStatus 1.3.6.1.4.1.14179.2.2.2.1.12
Operational status of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), up(2)  

bsnAPIfPortNumber 1.3.6.1.4.1.14179.2.2.2.1.13
Port number on Airespace Switch on which the traffic from this AP interface is received.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bsnAPIfPhyAntennaOptions 1.3.6.1.4.1.14179.2.2.2.1.14
This attribute specifies the Antenna types supported by the AP Radio whether it is internal or external or both. internalAndExternal(0)- internal and external antenna for both 11a and 11b internal(1) - only internal antenna is allowed. siacAp- 11b internal and 11a external external - only external antenna is allowed for 11a and 11b ext11bInt11a - external antenna for 11b and internal antenna for 11a.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER internalAndExternal(0), internal(1), siacAp(2), external(3), ext11bInt11a(4)  

bsnApIfNoOfUsers 1.3.6.1.4.1.14179.2.2.2.1.15
No of Users associated with this radio.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfWlanOverride 1.3.6.1.4.1.14179.2.2.2.1.16
This flag when disabled implies that all WLANs are available from this radio. However, if this is enabled, then only those WLANs that appear in the bsnApIfWlanOverrideTable will be available from this radio.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPIfPacketsSniffingFeature 1.3.6.1.4.1.14179.2.2.2.1.17
This flag when enabled implies that AP will sniff the 802.11a/bg packets. However, if it is enabled, then user should enter the server-ip-address on which Airopeek is running and the 802.11a/bg-channel-number to be sniffed. The above feature will work only when AP is in 'Sniffer' mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPIfSniffChannel 1.3.6.1.4.1.14179.2.2.2.1.18
This the 802.11a/bg-channel-number on which AP will sniff the packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ch0(0), ch1(1), ch2(2), ch3(3), ch4(4), ch5(5), ch6(6), ch7(7), ch8(8), ch9(9), ch10(10), ch11(11), ch12(12), ch13(13), ch14(14), ch20(20), ch21(21), ch22(22), ch23(23), ch24(24), ch25(25), ch26(26), ch34(34), ch36(36), ch38(38), ch40(40), ch42(42), ch44(44), ch46(46), ch48(48), ch52(52), ch56(56), ch60(60), ch64(64), ch100(100), ch104(104), ch108(108), ch112(112), ch116(116), ch120(120), ch124(124), ch128(128), ch132(132), ch136(136), ch140(140), ch149(149), ch153(153), ch157(157), ch161(161), ch165(165), ch169(169)  

bsnAPIfSniffServerIPAddress 1.3.6.1.4.1.14179.2.2.2.1.19
The machine ip address on which Airopeek application is running.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

bsnAPIfAntennaGain 1.3.6.1.4.1.14179.2.2.2.1.20
Represents antenna gain in multiple of 0.5 dBm. An integer value 4 means 4 x 0.5 = 2 dBm of gain
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..40  

bsnAPIfChannelList 1.3.6.1.4.1.14179.2.2.2.1.21
List of comma separated channels supported by this radio.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

bsnAPIfAbsolutePowerList 1.3.6.1.4.1.14179.2.2.2.1.22
List of comma separated absolute power levels supported by this radio.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

bsnAPIfRegulatoryDomainSupport 1.3.6.1.4.1.14179.2.2.2.1.23
If the regulatory domain on radio is supported or notSupported on the controller
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(0), supported(1)  

bsnAPIfAdminStatus 1.3.6.1.4.1.14179.2.2.2.1.34
Admin status of the interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(2), enable(1)  

bsnAPIfWlanOverrideTable 1.3.6.1.4.1.14179.2.2.21
Each entry represents an SSID added to the AP when the attribute bsnAPIfWlanOverride on the radio is enabled. This means only those WLANs on the switch that are added to this table will be available on such a radio.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfWlanOverrideEntry

bsnAPIfWlanOverrideEntry 1.3.6.1.4.1.14179.2.2.21.1
An entry in bsnAPIfWlanOverrideTable
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfWlanOverrideEntry  

bsnAPIfWlanOverrideId 1.3.6.1.4.1.14179.2.2.21.1.1
Index of the WLAN (bsnDot11EssIndex) added to the radio. Airespace Switch supports 16 Airespace WLANs so index will be from 1 to 16.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..16  

bsnAPIfWlanOverrideSsid 1.3.6.1.4.1.14179.2.2.21.1.2
SSID assigned to the override WLAN.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

bsnAPIfWlanOverrideRowStatus 1.3.6.1.4.1.14179.2.2.21.1.15
A row status type for the bsnAPIfWlanOverrideEntry
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnAPIfSmtParamTable 1.3.6.1.4.1.14179.2.2.3
Each entry represents SMT parameters on an 802.11 interface of an Airespace AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfSmtParamEntry

bsnAPIfSmtParamEntry 1.3.6.1.4.1.14179.2.2.3.1
An entry in bsnAPIfSmtParamTable
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfSmtParamEntry  

bsnAPIfDot11BeaconPeriod 1.3.6.1.4.1.14179.2.2.3.1.1
This attribute shall specify the number of TU that a AP Interface shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 20..1000  

bsnAPIfDot11MediumOccupancyLimit 1.3.6.1.4.1.14179.2.2.3.1.2
This attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

bsnAPIfDot11CFPPeriod 1.3.6.1.4.1.14179.2.2.3.1.3
The attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

bsnAPIfDot11CFPMaxDuration 1.3.6.1.4.1.14179.2.2.3.1.4
The attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bsnAPIfDot11OperationalRateSet 1.3.6.1.4.1.14179.2.2.3.1.5
This attribute shall specify the set of data rates at which the AP Interface may transmit data. Each octet contains a value representing a rate. Each rate shall be within the range from 2 to 127, corresponding to data rates in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s, and shall be supported (as indicated in the supported rates table) for receiving data. This value is reported in transmitted Beacon, Probe Request, Probe Response, Association Request, Association Response, Reassociation Request, and Reassociation Response frames, and is used to determine whether a BSS with which the AP Interface desires to synchronize is suitable. It is also used when starting a BSS, as specified in 10.3.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..126)  

bsnAPIfDot11DTIMPeriod 1.3.6.1.4.1.14179.2.2.3.1.6
This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

bsnAPIfDot11MultiDomainCapabilityImplemented 1.3.6.1.4.1.14179.2.2.3.1.7
This attribute, when TRUE, indicates that the AP Interface implementation is capable of supporting multiple regulatory domains. The capability is disabled, otherwise. The default value of this attribute is FALSE.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnAPIfDot11MultiDomainCapabilityEnabled 1.3.6.1.4.1.14179.2.2.3.1.8
This attribute, when TRUE, indicates that the capability of the AP Interface to operate in multiple regulatory domains is enabled. The capability is disabled, otherwise. The default value of this attribute is FALSE.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnAPIfDot11CountryString 1.3.6.1.4.1.14179.2.2.3.1.9
This attribute identifies the country in which the AP Interface is operating. The first two octets of this string is the two character country code as described in document ISO/IEC 3166-1. The third octet shall be one of the following: 1. an ASCII space character, if the regulations under which the AP Interface is operating encompass all environments in the country, 2. an ASCII 'O' character, if the regulations under which the AP Interface is operating are for an Outdoor environment only, or 3. an ASCII 'I' character, if the regulations under which the AP Interface is operating are for an Indoor environment only.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(3)  

bsnAPIfDot11SmtParamsConfigType 1.3.6.1.4.1.14179.2.2.3.1.10
This attribute suggests if the Station parameters for this radio are automatically set or have been customized.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER automatic(0), customized(1)  

bsnAPIfDot11BSSID 1.3.6.1.4.1.14179.2.2.3.1.30
BSSID of this AP config which would be the MAC Address of AP
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnAPIfMultiDomainCapabilityTable 1.3.6.1.4.1.14179.2.2.4
Each entry represents an 803.2 or an 802.11 interface in an Airespace AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfMultiDomainCapabilityEntry

bsnAPIfMultiDomainCapabilityEntry 1.3.6.1.4.1.14179.2.2.4.1
Each entry represents an 803.2 or an 802.11 interface in an Airespace AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfMultiDomainCapabilityEntry  

bsnAPIfDot11MaximumTransmitPowerLevel 1.3.6.1.4.1.14179.2.2.4.1.1
This attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfDot11FirstChannelNumber 1.3.6.1.4.1.14179.2.2.4.1.2
This attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfDot11NumberofChannels 1.3.6.1.4.1.14179.2.2.4.1.20
This attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfMacOperationParamTable 1.3.6.1.4.1.14179.2.2.5
Group contains MAC attributes pertaining to the operation of the MAC. These would be read only attributes as they would be updated by RRM Dynamic Algorithm. If user needs to configure them then they can only be configured globally
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfMacOperationParamEntry

bsnAPIfMacOperationParamEntry 1.3.6.1.4.1.14179.2.2.5.1
An entry in the bsnAPIfMacOperationParamEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfMacOperationParamEntry  

bsnAPIfDot11MacRTSThreshold 1.3.6.1.4.1.14179.2.2.5.1.1
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2347  

bsnAPIfDot11MacShortRetryLimit 1.3.6.1.4.1.14179.2.2.5.1.2
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

bsnAPIfDot11MacLongRetryLimit 1.3.6.1.4.1.14179.2.2.5.1.3
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

bsnAPIfDot11MacFragmentationThreshold 1.3.6.1.4.1.14179.2.2.5.1.4
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 256..2346  

bsnAPIfDot11MacMaxTransmitMSDULifetime 1.3.6.1.4.1.14179.2.2.5.1.5
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnAPIfDot11MacParamsConfigType 1.3.6.1.4.1.14179.2.2.5.1.6
This attribute suggests if the MAC parameters for this radio are automatically set or have been customized.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER automatic(0), customized(1)  

bsnAPIfDot11MacMaxReceiveLifetime 1.3.6.1.4.1.14179.2.2.5.1.25
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnAPIfDot11CountersTable 1.3.6.1.4.1.14179.2.2.6
Group containing attributes that are MAC counters. Each instance represents counters on a AP dot11 interface
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfDot11CountersEntry

bsnAPIfDot11CountersEntry 1.3.6.1.4.1.14179.2.2.6.1
An entry in the dot11CountersEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfDot11CountersEntry  

bsnAPIfDot11TransmittedFragmentCount 1.3.6.1.4.1.14179.2.2.6.1.1
This counter shall be incremented for an acknowledged MPDU with an individual address in the address 1 field or an MPDU with a multicast address in the address 1 field of type Data or Management.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11MulticastTransmittedFrameCount 1.3.6.1.4.1.14179.2.2.6.1.2
This counter shall increment only when the multicast bit is set in the destination MAC address of a successfully transmitted MSDU. When operating as a STA in an ESS, where these frames are directed to the AP, this implies having received an acknowledgment to all associated MPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11RetryCount 1.3.6.1.4.1.14179.2.2.6.1.3
This counter shall increment when an MSDU is successfully transmitted after one or more retransmissions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11MultipleRetryCount 1.3.6.1.4.1.14179.2.2.6.1.4
This counter shall increment when an MSDU is successfully transmitted after more than one retransmission.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11FrameDuplicateCount 1.3.6.1.4.1.14179.2.2.6.1.5
This counter shall increment when a frame is received that the Sequence Control field indicates is a duplicate.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11RTSSuccessCount 1.3.6.1.4.1.14179.2.2.6.1.6
This counter shall increment when a CTS is received in response to an RTS.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11RTSFailureCount 1.3.6.1.4.1.14179.2.2.6.1.7
This counter shall increment when a CTS is not received in response to an RTS.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11ACKFailureCount 1.3.6.1.4.1.14179.2.2.6.1.8
This counter shall increment when an ACK is not received when expected.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11ReceivedFragmentCount 1.3.6.1.4.1.14179.2.2.6.1.9
This counter shall be incremented for each successfully received MPDU of type Data or Management.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11MulticastReceivedFrameCount 1.3.6.1.4.1.14179.2.2.6.1.10
This counter shall increment when a MSDU is received with the multicast bit set in the destination MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11FCSErrorCount 1.3.6.1.4.1.14179.2.2.6.1.11
This counter shall increment when an FCS error is detected in a received MPDU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11TransmittedFrameCount 1.3.6.1.4.1.14179.2.2.6.1.12
This counter shall increment for each successfully transmitted MSDU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11WEPUndecryptableCount 1.3.6.1.4.1.14179.2.2.6.1.13
This counter shall increment when a frame is received with the WEP subfield of the Frame Control field set to one and the WEPOn value for the key mapped to the TA's MAC address indicates that the frame should not have been encrypted or that frame is discarded due to the receiving STA not implementing the privacy option.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11FailedCount 1.3.6.1.4.1.14179.2.2.6.1.33
This counter shall increment when an MSDU is not transmitted successfully due to the number of transmit attempts exceeding either the bsnAPIfDot11ShortRetryLimit or dot11LongRetryLimit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11PhyTxPowerTable 1.3.6.1.4.1.14179.2.2.8
Group of attributes for bsnAPIfDot11PhyTxPowerTable. Implemented as a table indexed on STA ID to allow for multiple instances on an Agent. This table has been deprecated. The level and power can be obtained from bsnAPIfTable(bsnAPIfAbsolutePowerList).
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfDot11PhyTxPowerEntry

bsnAPIfDot11PhyTxPowerEntry 1.3.6.1.4.1.14179.2.2.8.1
An entry in the bsnAPIfDot11PhyTxPower Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  BsnAPIfDot11PhyTxPowerEntry  

bsnAPIfDot11NumberSupportedPowerLevels 1.3.6.1.4.1.14179.2.2.8.1.1
The number of power levels supported by the PMD. This attribute can have a value of 1 to 8.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

bsnAPIfDot11TxPowerLevel1 1.3.6.1.4.1.14179.2.2.8.1.2
The transmit output power for LEVEL1 in mW. This is also the default power level. It is same as the Maximum power level available on an AP interface.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel2 1.3.6.1.4.1.14179.2.2.8.1.3
The transmit output power for LEVEL2 in mW. It is 1/2 of the Maximum power level available on an AP interface.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel3 1.3.6.1.4.1.14179.2.2.8.1.4
The transmit output power for LEVEL3 in mW. It is 1/4th of the Maximum power level available on an AP interface.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel4 1.3.6.1.4.1.14179.2.2.8.1.5
The transmit output power for LEVEL4 in mW. It is 1/8th of the Maximum power level available on an AP interface.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel5 1.3.6.1.4.1.14179.2.2.8.1.6
The transmit output power for LEVEL5 in mW. It is 1/16th of the Maximum power level available on an AP interface.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel6 1.3.6.1.4.1.14179.2.2.8.1.7
The transmit output power for LEVEL6 in mW. It is 1/32th of the Maximum power level available on an AP interface.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel7 1.3.6.1.4.1.14179.2.2.8.1.8
The transmit output power for LEVEL7 in mW. It is 1/64th of the Maximum power level available on an AP interface.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel8 1.3.6.1.4.1.14179.2.2.8.1.28
The transmit output power for LEVEL8 in mW. It is 1/128th of the Maximum power level available on an AP interface.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11PhyChannelTable 1.3.6.1.4.1.14179.2.2.9
Entry of attributes for bsnAPIfDot11PhyChannelEntry. Implemented as a table indexed on bsnAPDot3MacAddress, bsnAPIfSlotId allow for multiple instances on an Agent
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfDot11PhyChannelEntry

bsnAPIfDot11PhyChannelEntry 1.3.6.1.4.1.14179.2.2.9.1
An entry in the bsnAPIfDot11PhyChannelEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfDot11PhyChannelEntry  

bsnAPIfDot11CurrentCCAMode 1.3.6.1.4.1.14179.2.2.9.1.1
The current CCA method in operation.Valid values are: energy detect only (edonly) = 01, carrier sense only (csonly) = 02, carrier sense and energy detect (edandcs)= 04 carrier sense with timer (cswithtimer)= 08 high rate carrier sense and energy detect (hrcsanded)=16.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER edonly(1), csonly(2), edandcs(4), cswithtimer(8), hrcsanded(16)  

bsnAPIfDot11EDThreshold 1.3.6.1.4.1.14179.2.2.9.1.2
The current Energy Detect Threshold being used by the Channel PHY.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfDot11TIThreshold 1.3.6.1.4.1.14179.2.2.9.1.23
The Threshold being used to detect a busy medium (frequency). CCA shall report a busy medium upon detecting the RSSI above this threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfProfileThresholdConfigTable 1.3.6.1.4.1.14179.2.2.12
Table of attributes for various thresholds to be set on each Airespace AP Interface for Load performance profile , interference performance profile and Noise performance profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfProfileThresholdConfigEntry

bsnAPIfProfileThresholdConfigEntry 1.3.6.1.4.1.14179.2.2.12.1
An entry (conceptual row) in the Phy Thresholds Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfProfileThresholdConfigEntry  

bsnAPIfProfileParamAssignment 1.3.6.1.4.1.14179.2.2.12.1.1
If this value is automatic then Profile Parameters in bsnRrmDot11aAPProfile at the global level will be used. If this value is customized then Profile Parameters in bsnAPIfProfileThresholdConfig Table will be used and user can customize them per AP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER automatic(1), customized(2)  

bsnAPIfForeignInterferenceThreshold 1.3.6.1.4.1.14179.2.2.12.1.2
foreign interference threshold between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfForeignNoiseThreshold 1.3.6.1.4.1.14179.2.2.12.1.3
foreign noise threshold between -100 and -50 dBm.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -127..0  

bsnAPIfRFUtilizationThreshold 1.3.6.1.4.1.14179.2.2.12.1.4
RF utlization threshold between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfThroughputThreshold 1.3.6.1.4.1.14179.2.2.12.1.5
Airespace AP data-rate threshold between 1000 and 100000
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..1000000  

bsnAPIfMobilesThreshold 1.3.6.1.4.1.14179.2.2.12.1.6
Airespace AP mobiles threshold between 1 and 75
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..75  

bsnAPIfCoverageThreshold 1.3.6.1.4.1.14179.2.2.12.1.7
Airespace AP coverage threshold between 3 and 50
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 3..50  

bsnAPIfMobileMinExceptionLevel 1.3.6.1.4.1.14179.2.2.12.1.8
Airespace AP mobile minimum exception level between 1 and 1000
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..75  

bsnAPIfCoverageExceptionLevel 1.3.6.1.4.1.14179.2.2.12.1.28
Airespace AP coverage exception level between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfLoadParametersTable 1.3.6.1.4.1.14179.2.2.13
These are RRM performance related read only parameters per Airespace AP
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfLoadParametersEntry

bsnAPIfLoadParametersEntry 1.3.6.1.4.1.14179.2.2.13.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfLoadParametersEntry  

bsnAPIfLoadRxUtilization 1.3.6.1.4.1.14179.2.2.13.1.1
This is the percentage of time the Airespace AP receiver is busy operating on packets. It is a number from 0-100 representing a load from 0 to 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfLoadTxUtilization 1.3.6.1.4.1.14179.2.2.13.1.2
This is the percentage of time the Airespace AP transmitter is busy operating on packets. It is a number from 0-100 representing a load from 0 to 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfLoadChannelUtilization 1.3.6.1.4.1.14179.2.2.13.1.3
Channel Utilization
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfLoadNumOfClients 1.3.6.1.4.1.14179.2.2.13.1.4
This is the number of clients attached to this Airespace AP at the last measurement interval(This comes from APF)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfPoorSNRClients 1.3.6.1.4.1.14179.2.2.13.1.24
This is the number of clients with poor SNR attached to this Airespace AP at the last measurement interval ( This comes from APF ).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfChannelInterferenceInfoTable 1.3.6.1.4.1.14179.2.2.14
This is a table of channel information like interference and noise from other 802.11 networks on each channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfChannelInterferenceInfoEntry

bsnAPIfChannelInterferenceInfoEntry 1.3.6.1.4.1.14179.2.2.14.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfChannelInterferenceInfoEntry  

bsnAPIfInterferenceChannelNo 1.3.6.1.4.1.14179.2.2.14.1.1
Channel Number on AP
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfInterferencePower 1.3.6.1.4.1.14179.2.2.14.1.2
Power of Interference from other 802.11 networks on this channel
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfInterferenceUtilization 1.3.6.1.4.1.14179.2.2.14.1.22
Interference from other 802.11 networks on this channel
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfRadarChannelStatisticsTable 1.3.6.1.4.1.14179.2.2.24
This is a table of channel information on which radar signal were detected. This will give the list of channels and last heard timestamp. Radar signals are detected only on 5Ghz range. So this will be detected for 802.11a interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfRadarChannelStatisticsEntry

bsnAPIfRadarChannelStatisticsEntry 1.3.6.1.4.1.14179.2.2.24.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId, bsnAPIfRadarDetectedCannelNumber.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfRadarChannelStatisticsEntry  

bsnAPIfRadarDetectedChannelNumber 1.3.6.1.4.1.14179.2.2.24.1.1
Channel Number on which radar signals were detected.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfRadarSignalLastHeard 1.3.6.1.4.1.14179.2.2.24.1.2
This tells how many seconds ago radar signal was heard on the channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfChannelNoiseInfoTable 1.3.6.1.4.1.14179.2.2.15
This is a table of channel information like interference and noise from other 802.11 networks on each channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfChannelNoiseInfoEntry

bsnAPIfChannelNoiseInfoEntry 1.3.6.1.4.1.14179.2.2.15.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfChannelNoiseInfoEntry  

bsnAPIfNoiseChannelNo 1.3.6.1.4.1.14179.2.2.15.1.1
Channel Number on AP
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfDBNoisePower 1.3.6.1.4.1.14179.2.2.15.1.21
This is the average noise power in dBm on each channel that is available to Airespace AP
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfProfileStateTable 1.3.6.1.4.1.14179.2.2.16
This is a table of state of interference monitor on each Airespace AP
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfProfileStateEntry

bsnAPIfProfileStateEntry 1.3.6.1.4.1.14179.2.2.16.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfProfileStateEntry  

bsnAPIfLoadProfileState 1.3.6.1.4.1.14179.2.2.16.1.1
This field represents the current state of the LOAD monitor. This is a total measurement of the business of this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the Airespace AP profile. FAIL indicates the Airespace AP is not performing adequately against the LOAD profile.
Status: current Access: read-only
OBJECT-TYPE    
  ProfileState  

bsnAPIfInterferenceProfileState 1.3.6.1.4.1.14179.2.2.16.1.2
This field represents the current state of Interference monitor. This is a total measurement of the interference present at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the Interference profile. FAIL indicates the Airespace AP is not performing adequately against the Interference profile.
Status: current Access: read-only
OBJECT-TYPE    
  ProfileState  

bsnAPIfNoiseProfileState 1.3.6.1.4.1.14179.2.2.16.1.3
This field represents the current state of Noise monitor. This is a total measurement of the noise present at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the noise profile. FAIL indicates the Airespace AP is not performing adequately against the noise profile.
Status: current Access: read-only
OBJECT-TYPE    
  ProfileState  

bsnAPIfCoverageProfileState 1.3.6.1.4.1.14179.2.2.16.1.24
This field represents the current state of coverage monitor. This is a total measurement of the client coverage at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the coverage profile. FAIL indicates the Airespace AP is not performing adequately against the coverage profile.
Status: current Access: read-only
OBJECT-TYPE    
  ProfileState  

bsnAPIfRxNeighborsTable 1.3.6.1.4.1.14179.2.2.17
This is a table of Rx Neighbors for each Airespace AP with their RSSI value.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfRxNeighborsEntry

bsnAPIfRxNeighborsEntry 1.3.6.1.4.1.14179.2.2.17.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress bsnAPIfSlotId, bsnAPIfRxNeighborMacAddress
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfRxNeighborsEntry  

bsnAPIfRxNeighborMacAddress 1.3.6.1.4.1.14179.2.2.17.1.1
MAC Address of Rx Neighbor of the Airespace AP
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnAPIfRxNeighborIpAddress 1.3.6.1.4.1.14179.2.2.17.1.2
IP Address of Rx Neighbor of the Airespace AP
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bsnAPIfRxNeighborRSSI 1.3.6.1.4.1.14179.2.2.17.1.3
RSSI value of the Rx Neighbor
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfRxNeighborSlot 1.3.6.1.4.1.14179.2.2.17.1.24
Slot value of the Rx Neighbor
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfRxNeighborChannel 1.3.6.1.4.1.14179.2.2.17.1.26
This object represents Channel information which neighboring Access point is using.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfRxNeighborChannelWidth 1.3.6.1.4.1.14179.2.2.17.1.27
This object represents Channel bandwidth information which neighboring Access point is using.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER five(1), ten(2), twenty(3), aboveforty(4), belowforty(5)  

bsnMeshNodeTable 1.3.6.1.4.1.14179.2.2.22
This is a table of mesh nodes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMeshNodeEntry

bsnMeshNodeEntry 1.3.6.1.4.1.14179.2.2.22.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMeshNodeEntry  

bsnMeshNodeRole 1.3.6.1.4.1.14179.2.2.22.1.1
the role of this AP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER pap(0), rap(1)  

bsnMeshNodeGroup 1.3.6.1.4.1.14179.2.2.22.1.2
the bridge group name of this AP
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..10)  

bsnMeshNodeBackhaul 1.3.6.1.4.1.14179.2.2.22.1.3
the backhaul radio device for this AP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot11a(0), dot11b(1), dot11g(2)  

bsnMeshNodeBackhaulPAP 1.3.6.1.4.1.14179.2.2.22.1.4
the backhaul
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER auto(0), dot11a(1), dot11b(2), dot11g(3)  

bsnMeshNodeBackhaulRAP 1.3.6.1.4.1.14179.2.2.22.1.5
the backhaul radio device for this AP
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dot11a(0), dot11b(1), dot11g(2)  

bsnMeshNodeDataRate 1.3.6.1.4.1.14179.2.2.22.1.6
this nodes backhaul data rate
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bsnMeshNodeChannel 1.3.6.1.4.1.14179.2.2.22.1.7
this nodes backhaul channel
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMeshNodeRoutingState 1.3.6.1.4.1.14179.2.2.22.1.8
routing state
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER start(1), seek(2), sync(3), auth(4), maint(5)  

bsnMeshNodeMalformedNeighPackets 1.3.6.1.4.1.14179.2.2.22.1.9
the number of malformed neighbor packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNodePoorNeighSnr 1.3.6.1.4.1.14179.2.2.22.1.10
poor neighbor snr
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNodeBlacklistPackets 1.3.6.1.4.1.14179.2.2.22.1.11
the number of blacklist packets received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNodeInsufficientMemory 1.3.6.1.4.1.14179.2.2.22.1.12
occurences of insufficient memory conditions
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNodeRxNeighReq 1.3.6.1.4.1.14179.2.2.22.1.13
Rx neighbor requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNodeRxNeighRsp 1.3.6.1.4.1.14179.2.2.22.1.14
Rx neighbor responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNodeTxNeighReq 1.3.6.1.4.1.14179.2.2.22.1.15
Tx neighbor requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNodeTxNeighRsp 1.3.6.1.4.1.14179.2.2.22.1.16
Tx neighbor responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNodeParentChanges 1.3.6.1.4.1.14179.2.2.22.1.17
number of parent changes
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNodeNeighTimeout 1.3.6.1.4.1.14179.2.2.22.1.18
number of neighbor timeouts
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNodeParentMacAddress 1.3.6.1.4.1.14179.2.2.22.1.19
parents mac addressed
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnMeshNodeAPType 1.3.6.1.4.1.14179.2.2.22.1.20
the type of AP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER indoorBridge(5), outdoorBridge(6)  

bsnMeshNodeEthernetBridge 1.3.6.1.4.1.14179.2.2.22.1.21
enable : Enables ethernet bridging on the AP. disable : Disables ethernet bridging on the AP. Changes are only applicable when AP is in 'Bridge' mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnMeshNodeHops 1.3.6.1.4.1.14179.2.2.22.1.30
number of hops to rap
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMeshNeighsTable 1.3.6.1.4.1.14179.2.2.23
This is a table of mesh neighbors.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMeshNeighsEntry

bsnMeshNeighsEntry 1.3.6.1.4.1.14179.2.2.23.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnMeshNeighNeighMacAddress
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMeshNeighsEntry  

bsnMeshNeighMacAddress 1.3.6.1.4.1.14179.2.2.23.1.1
MAC Address of neighbor
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnMeshNeighType 1.3.6.1.4.1.14179.2.2.23.1.2
neighbor type
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER parent(0), tentparent(1), neigh(2), blacklisted(3), child(4)  

bsnMeshNeighState 1.3.6.1.4.1.14179.2.2.23.1.3
neighbor state
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER updated(0), needupdate(1)  

bsnMeshNeighSnr 1.3.6.1.4.1.14179.2.2.23.1.4
explicitly set SNR
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMeshNeighSnrUp 1.3.6.1.4.1.14179.2.2.23.1.5
snr up
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMeshNeighSnrDown 1.3.6.1.4.1.14179.2.2.23.1.6
snr down
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMeshNeighLinkSnr 1.3.6.1.4.1.14179.2.2.23.1.7
link snr
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMeshNeighAdjustedEase 1.3.6.1.4.1.14179.2.2.23.1.8
hops adjusted ease
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMeshNeighUnadjustedEase 1.3.6.1.4.1.14179.2.2.23.1.9
ease to root AP from this AP
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMeshNeighRapEase 1.3.6.1.4.1.14179.2.2.23.1.10
unadjusted ease received in last hello
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMeshNeighTxParent 1.3.6.1.4.1.14179.2.2.23.1.11
tx packets to this node while a parent
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNeighRxParent 1.3.6.1.4.1.14179.2.2.23.1.12
rx packets from this node while a parent
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNeighPoorSnr 1.3.6.1.4.1.14179.2.2.23.1.13
packets with poor snr received from this node
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMeshNeighLastUpdate 1.3.6.1.4.1.14179.2.2.23.1.14
last received hello from this neighbor
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnMeshNeighParentChange 1.3.6.1.4.1.14179.2.2.23.1.20
when this node last became parent
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfStationRSSICoverageInfoTable 1.3.6.1.4.1.14179.2.2.18
This is a table of channel information like interference and noise from other 802.11 networks on each channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfStationRSSICoverageInfoEntry

bsnAPIfStationRSSICoverageInfoEntry 1.3.6.1.4.1.14179.2.2.18.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfStationRSSICoverageInfoEntry  

bsnAPIfStationRSSICoverageIndex 1.3.6.1.4.1.14179.2.2.18.1.1
RSSI Coverage Index on AP
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfRSSILevel 1.3.6.1.4.1.14179.2.2.18.1.2
RSSI Level
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfStationCountOnRSSI 1.3.6.1.4.1.14179.2.2.18.1.23
Number of stations on this RSSI Level
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfStationSNRCoverageInfoTable 1.3.6.1.4.1.14179.2.2.19
This is a table of Signal to Noise ratio Coverage information on an AP Interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfStationSNRCoverageInfoEntry

bsnAPIfStationSNRCoverageInfoEntry 1.3.6.1.4.1.14179.2.2.19.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfStationSNRCoverageInfoEntry  

bsnAPIfStationSNRCoverageIndex 1.3.6.1.4.1.14179.2.2.19.1.1
SNR Coverage Index on AP
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfSNRLevel 1.3.6.1.4.1.14179.2.2.19.1.2
SNR Level
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfStationCountOnSNR 1.3.6.1.4.1.14179.2.2.19.1.23
Number of stations on this SNR Level
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfRecommendedRFParametersTable 1.3.6.1.4.1.14179.2.2.20
This table list Best Channel,Best TxPowerLevel, Best RTSThreshold,Best FragmentationThreshold etc for this AP Interface as determined by RRM.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfRecommendedRFParametersEntry

bsnAPIfRecommendedRFParametersEntry 1.3.6.1.4.1.14179.2.2.20.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPIfRecommendedRFParametersEntry  

bsnAPIfRecommendedChannelNumber 1.3.6.1.4.1.14179.2.2.20.1.1
Recommended ChannelNumber by RRM for this APIf
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfRecommendedTxPowerLevel 1.3.6.1.4.1.14179.2.2.20.1.2
Recommended TxPowerLevel by RRM for this APIf
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfRecommendedRTSThreshold 1.3.6.1.4.1.14179.2.2.20.1.3
Recommended RTSThreshold by RRM for this APIf
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnAPIfRecommendedFragmentationThreshold 1.3.6.1.4.1.14179.2.2.20.1.24
Recommended Fragmentation Threshold by RRM for this APIf
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11Config 1.3.6.1.4.1.14179.2.3.1
OBJECT IDENTIFIER    

bsnGlobalDot11PrivacyOptionImplemented 1.3.6.1.4.1.14179.2.3.1.1
This attribute, when true, shall indicate that the IEEE 802.11 WEP option is implemented. The default value of this attribute shall be false.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnGlobalDot11AuthenticationResponseTimeOut 1.3.6.1.4.1.14179.2.3.1.2
This attribute shall specify the number of TU that a responding STA should wait for the next frame in the authentication sequence.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 5..60  

bsnGlobalDot11MultiDomainCapabilityImplemented 1.3.6.1.4.1.14179.2.3.1.3
This attribute, when TRUE, indicates that the station implementation is capable of supporting multiple regulatory domains. The capability is disabled, otherwise. The default value of this attribute is FALSE.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11MultiDomainCapabilityEnabled 1.3.6.1.4.1.14179.2.3.1.4
This attribute, when TRUE, indicates that the capability of the station to operate in multiple regulatory domains is enabled. The capability is disabled, otherwise. The default value of this attribute is FALSE.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11CountryIndex 1.3.6.1.4.1.14179.2.3.1.5
This attribute identifies the country in which the station is operating.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER usa(1), canada(2), france(3), japan(4), mexico(5), spain(6), usalegacy(7), korearepublic(8), australia(9), austria(10), belgium(11), denmark(12), finland(13), germany(14), greece(15), ireland(16), italy(17), luxembourg(18), netherlands(19), portugal(20), sweden(21), unitedkingdom(22), none(23), india(24), hongkong(25), switzerland(26), iceland(27), norway(28), singapore(29), thailand(30), taiwan(31), cyprus(33), czechrepublic(34), estonia(35), hungary(36), lithuania(37), latvia(38), malaysia(39), newzealand(40), poland(41), slovenia(42), slovakrepublic(43), southafrica(44), usachan165(45), israel(46), israelOutdoor(47), argentina(48), brazil(49), saudiArabia(51), turkey(52), indonesia(53), china(54), koreaExtended(55), japan2(56), gibraltar(57), liechtenstein(58), malta(59), monaco(60), romania(61), russianfederation(62), chile(63), colombia(64), panama(65), peru(66), venezuela(67), philippines(68)  

bsnGlobalDot11LoadBalancing 1.3.6.1.4.1.14179.2.3.1.6
This attribute specifies if load balancing of clients is enabled on disabled. Global configuration of Load Balancing is now removed. Use cLWlanLoadBalancingEnable to configure it per WLAN.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11RogueTimer 1.3.6.1.4.1.14179.2.3.1.7
This attribute specifies in seconds, the time interval after which a Rogue Entry in Rogue Table will expire if no beacon is heard from a Rogue.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 120..3600  

bsnPrimaryMwarForAPs 1.3.6.1.4.1.14179.2.3.1.8
This attribute specifies if this Switch acts a Master Switch for the Airespace APs. So if an Airespace AP doesn't find its Primary Switch, it will associate with this Switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRtpProtocolPriority 1.3.6.1.4.1.14179.2.3.1.9
Real Time Protocol Priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nopriority(0), highpriority(1)  

bsnSystemCurrentTime 1.3.6.1.4.1.14179.2.3.1.10
This attribute will display the Current System time on the Switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bsnUpdateSystemTime 1.3.6.1.4.1.14179.2.3.1.11
Use this attribute to change the System time on the Switch. Specify the new time in this Format MM/DD/YYYY HH:MM:SS
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

bsnOperatingTemperatureEnvironment 1.3.6.1.4.1.14179.2.3.1.12
Operating Environment of the Airespace Switch. commercial is Commercial (0 to 40 C) and industrial is Industrial (-10 to 70 C)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER commercial(1), industrial(2), unknown(0)  

bsnSensorTemperature 1.3.6.1.4.1.14179.2.3.1.13
Current Internal Temperature of the unit in Centigrade
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnTemperatureAlarmLowLimit 1.3.6.1.4.1.14179.2.3.1.14
Internal Temperature Alarm Low Limit in Centigrade. If the bsnSensorTemperature goes below this limit bsnSensedTemperatureTooLow Alarm will be sent out
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnTemperatureAlarmHighLimit 1.3.6.1.4.1.14179.2.3.1.15
Internal Temperature Alarm High Limit in Centigrade. If the bsnSensorTemperature goes above this limit bsnSensedTemperatureTooHigh Alarm will be sent out
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnVirtualGatewayAddress 1.3.6.1.4.1.14179.2.3.1.16
Virtual Gateway Address of the Switch. This is used by web auth and Ipsec. If the virtual IP Address is changed, the Switch has to be rebooted for the new Address to take effect. This is now replaced by the Virtual Interface in bsnswitching MIB.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

bsnRFMobilityDomainName 1.3.6.1.4.1.14179.2.3.1.17
RF Mobility Group Name to which this Airespace Switch belongs. Airespace Switches on a network form a RF Group as well as a Mobility Group. RF Groups does the channel and power management of AP while Mobility Group does load balancing and hand off for clients.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnClientWatchListFeature 1.3.6.1.4.1.14179.2.3.1.18
This flag should be turned on for the client watch lists to be enabled on the switch. When enabled, the switch generates Client Association and Authentication traps for the watchlisted clients.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRogueLocationDiscoveryProtocol 1.3.6.1.4.1.14179.2.3.1.19
This flag should be turned on to enable the Rogue Location Discovery Protocol feature on the switch. We can either enable this feature for all the APs or only for APs in monitor mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), allAPs(1), monitorAPOnly(2)  

bsnRogueAutoContainFeature 1.3.6.1.4.1.14179.2.3.1.20
This flag should be turned on to allow the switch to contain the rogues automatically if detected on the wired network.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnOverAirProvisionApMode 1.3.6.1.4.1.14179.2.3.1.21
Over the Air Provisioning Mode for APs
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnMaximumNumberOfConcurrentLogins 1.3.6.1.4.1.14179.2.3.1.22
This attribute specifies the maximum number of concurrent logins that the switch will allow for a single user. A value 0 implies that there is no restriction on the number of concurrent logins with a single username.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..8  

bsnAutoContainRoguesAdvertisingSsid 1.3.6.1.4.1.14179.2.3.1.23
This flag should be set to 1 to allow the switch to contain automatically those rogues that are advertising our SSID. If value is 0, only an alarm will be generated when such a rogue is detected.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER alarmOnly(0), contain(1)  

bsnAutoContainAdhocNetworks 1.3.6.1.4.1.14179.2.3.1.24
This flag should be set to 1 to allow the switch to contain automatically the adhoc networks detected by the switch. If value is 0, only an alarm will be generated when such a network is detected.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER alarmOnly(0), contain(1)  

bsnAutoContainTrustedClientsOnRogueAps 1.3.6.1.4.1.14179.2.3.1.25
This flag should be set to 1 to allow the switch to contain automatically those trusted clients that are associated to rogue APs. If value is 0, only an alarm will be generated when such a client is detected.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER alarmOnly(0), contain(1)  

bsnValidateRogueClientsAgainstAAA 1.3.6.1.4.1.14179.2.3.1.26
This flag should be turned on to allow the switch to validate 'valid' mobiles associating with rogue APs. For example, if a client's MAC Address is found in the local MAC filter table, that client can be validated.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnSystemTimezoneDelta 1.3.6.1.4.1.14179.2.3.1.27
The delta (difference) between the local time and the Universal Coordinated Time in hours. For example, it is -8 for the PST and +1 for France. If the delta is -5.30 then this attribute will store -5 and bsnSystemTimezoneDeltaMinutes will store 30. This value i should be between -23 to +23
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bsnSystemTimezoneDeltaMinutes 1.3.6.1.4.1.14179.2.3.1.30
The minutes component of delta (difference) between the local time and the Universal Coordinated Time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bsnSystemTimezoneDaylightSavings 1.3.6.1.4.1.14179.2.3.1.28
This flag specifies if daylight savings are enabled for the current timezone.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAllowAuthorizeApAgainstAAA 1.3.6.1.4.1.14179.2.3.1.29
This flag specifies if LWAPP is allowed to get authorization via RADIUS or local database for an AP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnApFallbackEnabled 1.3.6.1.4.1.14179.2.3.1.31
This flag specifies if the APs should continue LWAPP discoveries to fallback to the primary switch in case they are not already associated with it i.e they are associated with their respective secondary or tertiary switch instead.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAppleTalkEnabled 1.3.6.1.4.1.14179.2.3.1.32
This flag turns on the appletalk bridging in the switch such that the packets from Apple clients that use appletalk format can be processed by the switch. When this flag is off, these packets are dropped.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnTrustedApPolicyConfig 1.3.6.1.4.1.14179.2.3.1.40
OBJECT IDENTIFIER    

bsnPolicyForMisconfiguredAps 1.3.6.1.4.1.14179.2.3.1.40.1
This flag should be turned on to allow the switch to contain misconfigured APs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER alarmOnly(0), contain(1)  

bsnEncryptionPolicyEnforced 1.3.6.1.4.1.14179.2.3.1.40.2
The encryption policy that is enforced on the trusted APs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), open(1), wep(2), wpa(3)  

bsnPreamblePolicyEnforced 1.3.6.1.4.1.14179.2.3.1.40.3
The preamble policy that is enforced on the trusted APs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), short(1), long(2)  

bsnDot11ModePolicyEnforced 1.3.6.1.4.1.14179.2.3.1.40.4
The 802.11 Mode policy that is enforced on the trusted APs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), dcfOnly(1), pcfOnly(2)  

bsnRadioTypePolicyEnforced 1.3.6.1.4.1.14179.2.3.1.40.5
The radio type policy that is enforced on the trusted APs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), aOnly(1), bOnly(2), bgOnly(3)  

bsnValidateSsidForTrustedAp 1.3.6.1.4.1.14179.2.3.1.40.6
If enabled, the SSID of trusted APs will be validated by the switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAlertIfTrustedApMissing 1.3.6.1.4.1.14179.2.3.1.40.7
If enabled, an alert will be generated when a trusted AP is missing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnTrustedApEntryExpirationTimeout 1.3.6.1.4.1.14179.2.3.1.40.8
This attribute specifies in seconds, the time interval after which a Trusted AP Entry will expire if no beacon is heard from that AP.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 120..3600  

bsnClientExclusionPolicyConfig 1.3.6.1.4.1.14179.2.3.1.41
OBJECT IDENTIFIER    

bsnExcessive80211AssocFailures 1.3.6.1.4.1.14179.2.3.1.41.1
This flag specifies if client should be excluded (blacklisted) if repeated 802.11 Association Failures occurs with a client.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnExcessive80211AuthFailures 1.3.6.1.4.1.14179.2.3.1.41.2
This flag specifies if client should be excluded (blacklisted) if repeated 802.11 Authentication Failures occurs with a client.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnExcessive8021xAuthFailures 1.3.6.1.4.1.14179.2.3.1.41.3
This flag specifies if client should be excluded (blacklisted) if repeated 802.1x Authentication Failures occurs with a client.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnExternalPolicyServerFailures 1.3.6.1.4.1.14179.2.3.1.41.4
This flag specifies if client should be excluded (blacklisted) if repeated external policy server failures occurs with a client.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnExcessiveWebAuthFailures 1.3.6.1.4.1.14179.2.3.1.41.5
This flag specifies if client should be excluded (blacklisted) if repeated Web Authentication Failures occurs with a client.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnIPTheftORReuse 1.3.6.1.4.1.14179.2.3.1.41.6
This flag specifies if client should be excluded (blacklisted) if it appears to be reusing an IP Address.(Possible IP Theft)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnSignatureConfig 1.3.6.1.4.1.14179.2.3.1.42
OBJECT IDENTIFIER    

bsnStandardSignatureTable 1.3.6.1.4.1.14179.2.3.1.42.1
The table listing Standard Signatures configured on the switch. The standard signatures are provided with the released product. The standard signatures can be updated via file download to the switch. The table is indexed by the precedence of the signatures.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnStandardSignatureEntry

bsnStandardSignatureEntry 1.3.6.1.4.1.14179.2.3.1.42.1.1
....
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnStandardSignatureEntry  

bsnStandardSignaturePrecedence 1.3.6.1.4.1.14179.2.3.1.42.1.1.1
Precedence of the signature. This specifies the order in which the signature is applied to a packet.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..100  

bsnStandardSignatureName 1.3.6.1.4.1.14179.2.3.1.42.1.1.2
This attribute is used to configure the name on a signature.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

bsnStandardSignatureDescription 1.3.6.1.4.1.14179.2.3.1.42.1.1.3
This attribute is used to configure the description of a signature.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

bsnStandardSignatureFrameType 1.3.6.1.4.1.14179.2.3.1.42.1.1.4
This attribute specifies the type of frame that needs to match a signature.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER management(0), data(1)  

bsnStandardSignatureAction 1.3.6.1.4.1.14179.2.3.1.42.1.1.5
This attribute specifies the action to be taken once a packet is found to match a signature.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), report(1), contain(2), exclude(3)  

bsnStandardSignatureState 1.3.6.1.4.1.14179.2.3.1.42.1.1.6
This attribute specifies the state of a signature. It is used to match packets only if the state is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bsnStandardSignatureFrequency 1.3.6.1.4.1.14179.2.3.1.42.1.1.7
This specifies the frequency of the matching packets after which the specified action is taken.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnStandardSignatureQuietTime 1.3.6.1.4.1.14179.2.3.1.42.1.1.8
This specifies the quiet time in seconds during which no matching packets are found after which the attack is considered stopped.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnStandardSignatureVersion 1.3.6.1.4.1.14179.2.3.1.42.1.1.9
This specifies the signature version.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..128  

bsnStandardSignatureConfigType 1.3.6.1.4.1.14179.2.3.1.42.1.1.10
This attribute specifies the type of Signature configuration. It's protocol when the protocol format is used in the UI to configure this. Pattern is the config type for all signatures in the released signature file and when signatures are configured using pattern format. Note: the signatures will be allowed to be i configured in later releases.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER pattern(0), protocol(1)  

bsnStandardSignatureEnable 1.3.6.1.4.1.14179.2.3.1.42.1.1.11
This object configures the status of a particular standard signature on LWAPP APs, for use in performing signature analysis on the received 802.11 data and/or management frames. A value of 'true' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'enable'. This makes the joined APs perform signature analysis on the received 802.11 data and/or management frames and report the discrepancies observed, if any, to the Controller. A value of 'false' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'disable'. The joined APs doesn't perform the signature analysis on the received 802.11 data and/or management frames for this particular signature, till the signature is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

bsnStandardSignatureMacInfo 1.3.6.1.4.1.14179.2.3.1.42.1.1.12
This object defines the pattern followed by the LWAPP APs to perform signature analysis with this Standard signature and report the results to the Controller.
Status: current Access: read-only
OBJECT-TYPE    
  BsnTxtSignatureMacInfo  

bsnStandardSignatureMacFreq 1.3.6.1.4.1.14179.2.3.1.42.1.1.13
This object specifies the frequency of matching packets from a particular source after which the specified action is taken.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnStandardSignatureRowStatus 1.3.6.1.4.1.14179.2.3.1.42.1.1.20
Row Status for creation/deletion. Signature will allowed to be created, deleted and edited in later releases.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

bsnStandardSignatureInterval 1.3.6.1.4.1.14179.2.3.1.42.1.1.21
Interval of the signature. This specifies the interval when the signature is applied to a packet.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..3600  

bsnStandardSignaturePatternTable 1.3.6.1.4.1.14179.2.3.1.42.2
The table listing the matching patterns specified for a i Standard Signature. These are instrumental in matching the signature with a packet. A maximum of 5 i patterns may be specifed for a signature. These are used for matching in the order of their index.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnStandardSignaturePatternEntry

bsnStandardSignaturePatternEntry 1.3.6.1.4.1.14179.2.3.1.42.2.1
....
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnStandardSignaturePatternEntry  

bsnStandardSignaturePatternIndex 1.3.6.1.4.1.14179.2.3.1.42.2.1.1
Index of the pattern. This specifies the order in which the pattern is checked against the packet contents.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..5  

bsnStandardSignaturePatternOffset 1.3.6.1.4.1.14179.2.3.1.42.2.1.2
Offset from the start of the packet where the AP looks for a match to the pattern.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..128  

bsnStandardSignaturePatternString 1.3.6.1.4.1.14179.2.3.1.42.2.1.3
This is the pattern string that the AP uses to match at the offset. Example: 0x616c7068615f3178
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..62)  

bsnStandardSignaturePatternMask 1.3.6.1.4.1.14179.2.3.1.42.2.1.4
This is the pattern mask. This is the bit mask that the AP uses to mask out the bits in the packet at the given offset. Example: 0xffffffffffffffff
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..62)  

bsnStandardSignaturePatternOffSetStart 1.3.6.1.4.1.14179.2.3.1.42.2.1.5
This object indicates how an offset should be applied while doing signature analysis for QOS and non-QOS data frames with this standard signature.
Status: current Access: read-only
OBJECT-TYPE    
  BsnSignaturePatternOffSetStart  

bsnStandardSignaturePatternRowStatus 1.3.6.1.4.1.14179.2.3.1.42.2.1.15
Row Status for creation/deletion. Signature Pattern will allowed to be created, deleted and edited in later releases.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

bsnCustomSignatureTable 1.3.6.1.4.1.14179.2.3.1.42.3
The table listing Standard Signatures configured on the switch. The standard signatures are provided with the released product. The standard signatures can be updated via file download to the switch. The table is indexed by the precedence of the signatures.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnCustomSignatureEntry

bsnCustomSignatureEntry 1.3.6.1.4.1.14179.2.3.1.42.3.1
....
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnCustomSignatureEntry  

bsnCustomSignaturePrecedence 1.3.6.1.4.1.14179.2.3.1.42.3.1.1
Precedence of the signature. This specifies the order in which the signature is applied to a packet.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..100  

bsnCustomSignatureName 1.3.6.1.4.1.14179.2.3.1.42.3.1.2
This attribute is used to configure the name on a signature.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

bsnCustomSignatureDescription 1.3.6.1.4.1.14179.2.3.1.42.3.1.3
This attribute is used to configure the description of a signature.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

bsnCustomSignatureFrameType 1.3.6.1.4.1.14179.2.3.1.42.3.1.4
This attribute specifies the type of frame that needs to match a signature.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER management(0), data(1)  

bsnCustomSignatureAction 1.3.6.1.4.1.14179.2.3.1.42.3.1.5
This attribute specifies the action to be taken once a packet is found to match a signature.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), report(1), contain(2), exclude(3)  

bsnCustomSignatureState 1.3.6.1.4.1.14179.2.3.1.42.3.1.6
This attribute specifies the state of a signature. It is used to match packets only if the state is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bsnCustomSignatureFrequency 1.3.6.1.4.1.14179.2.3.1.42.3.1.7
This specifies the frequency of the matching packets after which the specified action is taken.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnCustomSignatureQuietTime 1.3.6.1.4.1.14179.2.3.1.42.3.1.8
This specifies the quiet time in seconds during which no matching packets are found after which the attack is considered stopped.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnCustomSignatureVersion 1.3.6.1.4.1.14179.2.3.1.42.3.1.9
This specifies the signature version.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..128  

bsnCustomSignatureConfigType 1.3.6.1.4.1.14179.2.3.1.42.3.1.10
This attribute specifies the type of Signature configuration. It's protocol when the protocol format is used in the UI to configure this. Pattern is the config type for all signatures in the released signature file and when signatures are configured using pattern format. Note: the signatures will be allowed to be configured in later releases.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER pattern(0), protocol(1)  

bsnCustomSignatureEnable 1.3.6.1.4.1.14179.2.3.1.42.3.1.11
This object configures the status of a particular Custom signature on LWAPP APs, for use in performing signature analysis on the received 802.11 data and/or management frames. A value of 'true' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'enable'. This makes the joined APs perform signature analysis on the received 802.11 data and/or management frames and report the discrepancies observed, if any, to the Controller. A value of 'false' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'disable'. The joined APs doesn't perform the signature analysis on the received 802.11 data and/or management frames for this particular signature, till the signature is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

bsnCustomSignatureMacInfo 1.3.6.1.4.1.14179.2.3.1.42.3.1.12
This object defines the pattern followed by the LWAPP APs to perform signature analysis with this Custom signature and report the results to the Controller.
Status: current Access: read-only
OBJECT-TYPE    
  BsnTxtSignatureMacInfo  

bsnCustomSignatureMacFreq 1.3.6.1.4.1.14179.2.3.1.42.3.1.13
This object specifies the frequency of matching packets from a particular source after which the specified action is taken.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnCustomSignatureRowStatus 1.3.6.1.4.1.14179.2.3.1.42.3.1.20
Row Status for creation/deletion. Signature will allowed to be created, deleted and edited in later releases.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

bsnCustomSignatureInterval 1.3.6.1.4.1.14179.2.3.1.42.3.1.21
Interval of the signature. This specifies the interval when the signature is applied to a packet.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..3600  

bsnCustomSignaturePatternTable 1.3.6.1.4.1.14179.2.3.1.42.4
The table listing the matching patterns specified for a Standard Signature. These are instrumental in matching the signature with a packet. A maximum of 5 patterns may be specifed for a signature. These are used for matching in the order of their index.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnCustomSignaturePatternEntry

bsnCustomSignaturePatternEntry 1.3.6.1.4.1.14179.2.3.1.42.4.1
....
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnCustomSignaturePatternEntry  

bsnCustomSignaturePatternIndex 1.3.6.1.4.1.14179.2.3.1.42.4.1.1
Index of the pattern. This specifies the order in which the pattern is checked against the packet contents.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..5  

bsnCustomSignaturePatternOffset 1.3.6.1.4.1.14179.2.3.1.42.4.1.2
Offset from the start of the packet where the AP looks for a match to the pattern.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..128  

bsnCustomSignaturePatternString 1.3.6.1.4.1.14179.2.3.1.42.4.1.3
This is the pattern string that the AP uses to match at the offset. Example: 0x616c7068615f3178
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..62)  

bsnCustomSignaturePatternMask 1.3.6.1.4.1.14179.2.3.1.42.4.1.4
This is the pattern mask. This is the bit mask that the AP uses to mask out the bits in the packet at the given offset. Example: 0xffffffffffffffff
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..62)  

bsnCustomSignaturePatternOffSetStart 1.3.6.1.4.1.14179.2.3.1.42.4.1.5
This object indicates how an offset should be applied while doing signature analysis for QOS and non-QOS data frames with this custom signature.
Status: current Access: read-only
OBJECT-TYPE    
  BsnSignaturePatternOffSetStart  

bsnCustomSignaturePatternRowStatus 1.3.6.1.4.1.14179.2.3.1.42.4.1.15
Row Status for creation/deletion. Signature Pattern will allowed to be created, deleted and edited in later releases.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

bsnSignatureCheckState 1.3.6.1.4.1.14179.2.3.1.42.5
This flag should be enabled to enforce check of all standard and custom signatures. If disabled, there will be no check for signatures, both custom and standard, by the switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRfIdTagConfig 1.3.6.1.4.1.14179.2.3.1.43
OBJECT IDENTIFIER    

bsnRfIdTagStatus 1.3.6.1.4.1.14179.2.3.1.43.1
This flag should be turned on to allow the switch to collect data for tags.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRfIdTagDataTimeout 1.3.6.1.4.1.14179.2.3.1.43.2
This is the number of seconds after which the tag data is deleted by the switch from its database if it didn't hear from the tag again.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 60..7200  

bsnRfIdTagAutoTimeoutStatus 1.3.6.1.4.1.14179.2.3.1.43.3
This flag should be turned on to allow auto deletion of tag data in the switch after expiration of Tag Data Timeout
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPNeighborAuthConfig 1.3.6.1.4.1.14179.2.3.1.44
OBJECT IDENTIFIER    

bsnAPNeighborAuthStatus 1.3.6.1.4.1.14179.2.3.1.44.1
This flag should be turned on to allow the AP-Neighbor Authentication feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPNeighborAuthAlarmThreshold 1.3.6.1.4.1.14179.2.3.1.44.2
Authentication alarm trigger threshold.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

bsnRFNetworkName 1.3.6.1.4.1.14179.2.3.1.45
RF Network Group Name to which this Airespace Switch belongs. Airespace Switches on a network form a RF Network Group as well as a Mobility Group. RF Network Groups does the channel and power management of AP while Mobility Group does load balancing and hand off for clients.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..19)  

bsnFastSSIDChangeFeature 1.3.6.1.4.1.14179.2.3.1.46
Configures Fast SSID changing feature for mobile-stations. When enabled, permits mobile-stations to change SSIDs without having to block and wait for SSID-cleanup on the switch to occur.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnBridgingPolicyConfig 1.3.6.1.4.1.14179.2.3.1.47
OBJECT IDENTIFIER    

bsnBridgingZeroTouchConfig 1.3.6.1.4.1.14179.2.3.1.47.1
If enabled, allows new bridging APs to negotiate with the switch to acquire the shared secret key.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnBridgingSharedSecretKey 1.3.6.1.4.1.14179.2.3.1.47.2
Key that is used to negotiate a secure LWAPP connection between a switch and a bridging or mesh AP.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnGlobalDot11b 1.3.6.1.4.1.14179.2.3.2
OBJECT IDENTIFIER    

bsnGlobalDot11a 1.3.6.1.4.1.14179.2.3.3
OBJECT IDENTIFIER    

bsnGlobalDot11h 1.3.6.1.4.1.14179.2.3.4
OBJECT IDENTIFIER    

bsnGlobalDot11bConfig 1.3.6.1.4.1.14179.2.3.2.1
OBJECT IDENTIFIER    

bsnGlobalDot11bNetworkStatus 1.3.6.1.4.1.14179.2.3.2.1.1
802.11b Network Admin Status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11bBeaconPeriod 1.3.6.1.4.1.14179.2.3.2.1.2
This attribute shall specify the number of TU that a AP Radio shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 20..1000  

bsnGlobalDot11bDynamicChannelAssignment 1.3.6.1.4.1.14179.2.3.2.1.3
Dynamic channel assignment(DCA) has three modes. When the mode is auto, the channel assignment will be periodically updated for all Airespace APs that permit this operation. When the DCA is runOnce, channel assignments are updated based on the UPDATE_CMD received from the management. When the DCA is static, no dynamic channel assignments occurs and value are set to their global default. Default is auto.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER automatic(1), runOnce(2), static(3)  

bsnGlobalDot11bCurrentChannel 1.3.6.1.4.1.14179.2.3.2.1.4
The current operating frequency channel of the DSSS PHY. Valid channel numbers are as defined in 15.4.6.2. This attribute will be read-only if bsnAPIfPhyChannelAutomaticOn is true.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..14  

bsnGlobalDot11bDynamicChannelUpdateInterval 1.3.6.1.4.1.14179.2.3.2.1.5
When Channel dynamic alogirthm is running, this interval (in secs) specifies how often Channel assignement updates are attempted on an Airespace AP. NOTE: hysteresis is built into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11bInputsForDCA 1.3.6.1.4.1.14179.2.3.2.1.6
This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 SIGNAL STRENGTH 1 NOISE 2 FOREIGN INTERFERENCE 4 LOAD 8 DEVICE INTERFERENCE 32 Default value is 63( all bits on).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11bChannelUpdateCmdInvoke 1.3.6.1.4.1.14179.2.3.2.1.7
When set to activate this starts a DCA calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnGlobalDot11bChannelUpdateCmdStatus 1.3.6.1.4.1.14179.2.3.2.1.8
After setting bsnGlobalDot11bChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bDynamicTransmitPowerControl 1.3.6.1.4.1.14179.2.3.2.1.9
Dynamic transmit power (DTP) has three modes. When the mode is auto, the transmit power of each Airespace AP will be periodically updated for all Airespace APs that permit this operation. When the DTP is runOnce,transmit power update will occur based on the UPDATE_CMD received from the management. When the DTP is static, no dynamic transmit power updates occur and their global defaults are used. Default is auto.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER automatic(1), runOnce(2), static(3)  

bsnGlobalDot11bDynamicTxPowerControlInterval 1.3.6.1.4.1.14179.2.3.2.1.10
When Tx PowerControl dynamic alogirthm is running, this interval(in secs) specifies how often TxPower control updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11bCurrentTxPowerLevel 1.3.6.1.4.1.14179.2.3.2.1.11
The TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..5  

bsnGlobalDot11bInputsForDTP 1.3.6.1.4.1.14179.2.3.2.1.12
This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 LOAD 1 SIGNAL STRENGTH 2 FOREIGN INTERFERENCE 4 NOISE 8 Default value is 15( all bits on).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11bPowerUpdateCmdInvoke 1.3.6.1.4.1.14179.2.3.2.1.13
When set to activate this starts a DTP calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnGlobalDot11bPowerUpdateCmdStatus 1.3.6.1.4.1.14179.2.3.2.1.14
After setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bDataRate1Mhz 1.3.6.1.4.1.14179.2.3.2.1.15
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate2Mhz 1.3.6.1.4.1.14179.2.3.2.1.16
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate5AndHalfMhz 1.3.6.1.4.1.14179.2.3.2.1.17
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate11Mhz 1.3.6.1.4.1.14179.2.3.2.1.18
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bShortPreamble 1.3.6.1.4.1.14179.2.3.2.1.19
802.11b Short Preamble.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11bDot11gSupport 1.3.6.1.4.1.14179.2.3.2.1.20
This attribute is enabled to also support 802.11g protocol on the 802.11b network. Enabling 802.11g allows additional data rates: 6, 9, 12, 18, 24, 36, 48, 54 Mbps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11bDataRate6Mhz 1.3.6.1.4.1.14179.2.3.2.1.21
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate9Mhz 1.3.6.1.4.1.14179.2.3.2.1.22
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate12Mhz 1.3.6.1.4.1.14179.2.3.2.1.23
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate18Mhz 1.3.6.1.4.1.14179.2.3.2.1.24
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate24Mhz 1.3.6.1.4.1.14179.2.3.2.1.25
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate36Mhz 1.3.6.1.4.1.14179.2.3.2.1.26
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate48Mhz 1.3.6.1.4.1.14179.2.3.2.1.27
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate54Mhz 1.3.6.1.4.1.14179.2.3.2.1.28
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bPicoCellMode 1.3.6.1.4.1.14179.2.3.2.1.29
Configures the 802.11b pico-cell mode. This cannot be enabled when the Fast Roaming Mode is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnGlobalDot11bFastRoamingMode 1.3.6.1.4.1.14179.2.3.2.1.30
Configures the 802.11b fast-roaming mode. This cannot be enabled when the Pico Cell Mode is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11bFastRoamingVoipMinRate 1.3.6.1.4.1.14179.2.3.2.1.31
Configures the minimum transmission rate allowed for VoIP on any 802.11b radio.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER undefined(0), rate1Mbps(1), rate2Mbps(2), rate5andHalfMbps(3), rate11Mbps(4)  

bsnGlobalDot11bFastRoamingVoipPercentage 1.3.6.1.4.1.14179.2.3.2.1.32
Configures the percentage of effective bandwidth for the minimum rate reserved for VoIP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), twentyfive(2), fifty(3), seventyfive(4), hundred(5)  

bsnGlobalDot11b80211eMaxBandwidth 1.3.6.1.4.1.14179.2.3.2.1.33
This represents the maximum bandwidth allocated to 802.11e clients. It is expressed as percentage of the total bandwidth of 802.11b network. The value of this attribute can vary from 0 to 100.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnGlobalDot11bDTPCSupport 1.3.6.1.4.1.14179.2.3.2.1.34
This attribute may be used to enable the DTPC support on all 802.11b/g radios. DTPC or Dynamic Transmit Power Control support means that the radio's transmit power will be advertised in the beacons and probe responses.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11bPhy 1.3.6.1.4.1.14179.2.3.2.2
OBJECT IDENTIFIER    

bsnGlobalDot11bMediumOccupancyLimit 1.3.6.1.4.1.14179.2.3.2.2.1
This attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

bsnGlobalDot11bCFPPeriod 1.3.6.1.4.1.14179.2.3.2.2.2
The attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

bsnGlobalDot11bCFPMaxDuration 1.3.6.1.4.1.14179.2.3.2.2.3
The attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bsnGlobalDot11bCFPollable 1.3.6.1.4.1.14179.2.3.2.2.5
When this attribute is true, it shall indicate that the STA is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the STA is not able to respond to a CF-Poll with a data frame within a SIFS time.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11bCFPollRequest 1.3.6.1.4.1.14179.2.3.2.2.6
Specifies wheather CFP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11bDTIMPeriod 1.3.6.1.4.1.14179.2.3.2.2.7
This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11bMaximumTransmitPowerLevel 1.3.6.1.4.1.14179.2.3.2.2.8
This attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bFirstChannelNumber 1.3.6.1.4.1.14179.2.3.2.2.9
This attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bNumberofChannels 1.3.6.1.4.1.14179.2.3.2.2.10
This attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bRTSThreshold 1.3.6.1.4.1.14179.2.3.2.2.11
This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the MPDU is of type Data or Management, the MPDU has an individual address in the Address1 field, and the length of the MPDU is greater than this threshold. (For additional details, refer to Table 21 in 9.7.) Setting this attribute to be larger than the maximum MSDU size shall have the effect of turning off the RTS/CTS handshake for frames of Data or Management type transmitted by this STA. Setting this attribute to zero shall have the effect of turning on the RTS/CTS handshake for all frames of Data or Management type transmitted by this STA. The default value of this attribute shall be 2347.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2347  

bsnGlobalDot11bShortRetryLimit 1.3.6.1.4.1.14179.2.3.2.2.12
This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is less than or equal to bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 7.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11bLongRetryLimit 1.3.6.1.4.1.14179.2.3.2.2.13
This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is greater than bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 4.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11bFragmentationThreshold 1.3.6.1.4.1.14179.2.3.2.2.14
This attribute shall specify the current maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. An MSDU or MMPDU shall be fragmented when the resulting frame has individual address in the Address1 field, and the length of the frame is larger than this threshold. The default value for this attribute shall be the lesser of 2346 or the aMPDUMaxLength of the attached PHY and shall never exceed the lesser of 2346 or the aMPDUMaxLength of the attached PHY. The value of this attribute shall never be less than 256.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 256..2346  

bsnGlobalDot11bMaxTransmitMSDULifetime 1.3.6.1.4.1.14179.2.3.2.2.15
The MaxTransmitMSDULifetime shall be the elapsed time in TU, after the initial transmission of an MSDU, after which further attempts to transmit the MSDU shall be terminated. The default value of this attribute shall be 512.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnGlobalDot11bMaxReceiveLifetime 1.3.6.1.4.1.14179.2.3.2.2.16
The MaxReceiveLifetime shall be the elapsed time in TU, after the initial reception of a fragmented MMPDU or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. The default value shall be 512.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnGlobalDot11bEDThreshold 1.3.6.1.4.1.14179.2.3.2.2.17
The current Energy Detect Threshold being used by the DSSS PHY.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bChannelAgilityEnabled 1.3.6.1.4.1.14179.2.3.2.2.18
This attribute indicates that the PHY channel agility functionality is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11bPBCCOptionImplemented 1.3.6.1.4.1.14179.2.3.2.2.19
This attribute, when true, shall indicate that the PBCC modulation option as defined in subclause 18.4.6.6 is implemented. The default value of this attribute shall be false.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11bShortPreambleOptionImplemented 1.3.6.1.4.1.14179.2.3.2.2.20
This attribute, when true, shall indicate that the short preamble option as defined in subclause 18.2.2.2 is implemented. The default value of this attribute shall be false.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11aConfig 1.3.6.1.4.1.14179.2.3.3.1
OBJECT IDENTIFIER    

bsnGlobalDot11aNetworkStatus 1.3.6.1.4.1.14179.2.3.3.1.1
Dot11a Network Status
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aLowBandNetwork 1.3.6.1.4.1.14179.2.3.3.1.2
Dot11a Low Band Network Status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aMediumBandNetwork 1.3.6.1.4.1.14179.2.3.3.1.3
Dot11a Mid Band Network Status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aHighBandNetwork 1.3.6.1.4.1.14179.2.3.3.1.4
Dot11a High Band Network Status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aBeaconPeriod 1.3.6.1.4.1.14179.2.3.3.1.5
This attribute shall specify the number of TU that a AP Radio shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 20..1000  

bsnGlobalDot11aDynamicChannelAssignment 1.3.6.1.4.1.14179.2.3.3.1.6
Dynamic channel assignment(DCA) has three modes. When the mode is auto, the channel assignment will be periodically updated for all Airespace APs that permit this operation. When the DCA is runOnce, channel assignments are updated based on the UPDATE_CMD received from the management. When the DCA is static, no dynamic channel assignments occurs and value are set to their global default. Default is auto.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER automatic(1), runOnce(2), static(3)  

bsnGlobalDot11aCurrentChannel 1.3.6.1.4.1.14179.2.3.3.1.7
The number of the current operating frequency channel of the OFDM PHY.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99  

bsnGlobalDot11aDynamicChannelUpdateInterval 1.3.6.1.4.1.14179.2.3.3.1.8
When Channel dynamic alogirthm is running, this interval(in secs) specifies how often Channel assignement updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11aInputsForDCA 1.3.6.1.4.1.14179.2.3.3.1.9
This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 SIGNAL STRENGTH 1 NOISE 2 FOREIGN INTERFERENCE 4 LOAD 8 DEVICE INTERFERENCE 32 Default value is 63( all bits on).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11aChannelUpdateCmdInvoke 1.3.6.1.4.1.14179.2.3.3.1.10
When set to activate this starts a DCA calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnGlobalDot11aChannelUpdateCmdStatus 1.3.6.1.4.1.14179.2.3.3.1.11
After setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aDynamicTransmitPowerControl 1.3.6.1.4.1.14179.2.3.3.1.12
Dynamic transmit power (DTP) has three modes. When the mode is auto, the transmit power of each Airespace AP will be periodically updated for all Airespace APs that permit this operation. When the DTP is runOnce,transmit power update will occur based on the UPDATE_CMD received from the management. When the DTP is static, no dynamic transmit power updates occur and their global defaults are used. Default is auto.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER automatic(1), runOnce(2), static(3)  

bsnGlobalDot11aCurrentTxPowerLevel 1.3.6.1.4.1.14179.2.3.3.1.13
The TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..5  

bsnGlobalDot11aDynamicTxPowerControlInterval 1.3.6.1.4.1.14179.2.3.3.1.14
When Tx PowerControl dynamic alogirthm is running, this interval(in secs) specifies how often TxPower control updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11aInputsForDTP 1.3.6.1.4.1.14179.2.3.3.1.15
This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 LOAD 1 SIGNAL STRENGTH 2 FOREIGN INTERFERENCE 4 NOISE 8 Default value is 15( all bits on).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11aPowerUpdateCmdInvoke 1.3.6.1.4.1.14179.2.3.3.1.16
When set to activate this starts a DTP calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnGlobalDot11aPowerUpdateCmdStatus 1.3.6.1.4.1.14179.2.3.3.1.17
After setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aDataRate6Mhz 1.3.6.1.4.1.14179.2.3.3.1.19
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate9Mhz 1.3.6.1.4.1.14179.2.3.3.1.20
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate12Mhz 1.3.6.1.4.1.14179.2.3.3.1.21
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate18Mhz 1.3.6.1.4.1.14179.2.3.3.1.22
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate24Mhz 1.3.6.1.4.1.14179.2.3.3.1.23
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate36Mhz 1.3.6.1.4.1.14179.2.3.3.1.24
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate48Mhz 1.3.6.1.4.1.14179.2.3.3.1.25
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate54Mhz 1.3.6.1.4.1.14179.2.3.3.1.26
Specify if this rate is supported or mandatory or disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aPicoCellMode 1.3.6.1.4.1.14179.2.3.3.1.27
Configures the 802.11a pico-cell mode. This cannot be enabled when the Fast Roaming Mode is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnGlobalDot11aFastRoamingMode 1.3.6.1.4.1.14179.2.3.3.1.28
Configures the 802.11a fast-roaming mode. This cannot be enabled when the Pico Cell Mode is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aFastRoamingVoipMinRate 1.3.6.1.4.1.14179.2.3.3.1.29
Configures the minimum transmission rate allowed for VoIP on any 802.11a radio.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER undefined(0), rate1Mbps(1), rate2Mbps(2), rate5andHalfMbps(3), rate11Mbps(4)  

bsnGlobalDot11aFastRoamingVoipPercentage 1.3.6.1.4.1.14179.2.3.3.1.30
Configures the percentage of effective bandwidth for the minimum rate reserved for VoIP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), twentyfive(2), fifty(3), seventyfive(4), hundred(5)  

bsnGlobalDot11a80211eMaxBandwidth 1.3.6.1.4.1.14179.2.3.3.1.31
This represents the maximum bandwidth allocated to 802.11e clients. It is expressed as percentage of the total bandwidth of 802.11a network. The value of this attribute can vary from 0 to 100.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnGlobalDot11aDTPCSupport 1.3.6.1.4.1.14179.2.3.3.1.32
This attribute may be used to enable the DTPC support on all 802.11a radios. DTPC or Dynamic Transmit Power Control support means that the radio's transmit power will be advertised in the beacons and probe responses.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aPhy 1.3.6.1.4.1.14179.2.3.3.2
OBJECT IDENTIFIER    

bsnGlobalDot11aMediumOccupancyLimit 1.3.6.1.4.1.14179.2.3.3.2.1
This attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

bsnGlobalDot11aCFPPeriod 1.3.6.1.4.1.14179.2.3.3.2.2
The attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

bsnGlobalDot11aCFPMaxDuration 1.3.6.1.4.1.14179.2.3.3.2.3
The attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bsnGlobalDot11aCFPollable 1.3.6.1.4.1.14179.2.3.3.2.5
When this attribute is true, it shall indicate that the STA is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the STA is not able to respond to a CF-Poll with a data frame within a SIFS time.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11aCFPollRequest 1.3.6.1.4.1.14179.2.3.3.2.6
Specifies whether CFP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11aDTIMPeriod 1.3.6.1.4.1.14179.2.3.3.2.7
This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11aMaximumTransmitPowerLevel 1.3.6.1.4.1.14179.2.3.3.2.8
This attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aFirstChannelNumber 1.3.6.1.4.1.14179.2.3.3.2.9
This attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aNumberofChannels 1.3.6.1.4.1.14179.2.3.3.2.10
This attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aRTSThreshold 1.3.6.1.4.1.14179.2.3.3.2.11
This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the MPDU is of type Data or Management, the MPDU has an individual address in the Address1 field, and the length of the MPDU is greater than this threshold. (For additional details, refer to Table 21 in 9.7.) Setting this attribute to be larger than the maximum MSDU size shall have the effect of turning off the RTS/CTS handshake for frames of Data or Management type transmitted by this STA. Setting this attribute to zero shall have the effect of turning on the RTS/CTS handshake for all frames of Data or Management type transmitted by this STA. The default value of this attribute shall be 2347.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2347  

bsnGlobalDot11aShortRetryLimit 1.3.6.1.4.1.14179.2.3.3.2.12
This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is less than or equal to bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 7.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11aLongRetryLimit 1.3.6.1.4.1.14179.2.3.3.2.13
This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is greater than bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 4.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11aFragmentationThreshold 1.3.6.1.4.1.14179.2.3.3.2.14
This attribute shall specify the current maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. MSDU or MMPDU shall be fragmented when the resulting frame has an individual address in the Address1 field, and the length of the frame is larger than this threshold. The default value for this attribute shall be the lesser of 2346 or the aMPDUMaxLength of the attached PHY and shall never exceed the lesser of 2346 or the aMPDUMaxLength of the attached PHY. The value of this attribute shall never be less than 256.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 256..2346  

bsnGlobalDot11aMaxTransmitMSDULifetime 1.3.6.1.4.1.14179.2.3.3.2.15
The MaxTransmitMSDULifetime shall be the elapsed time in TU, after the initial transmission of an MSDU, after which further attempts to transmit the MSDU shall be terminated. The default value of this attribute shall be 512.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnGlobalDot11aMaxReceiveLifetime 1.3.6.1.4.1.14179.2.3.3.2.16
The MaxReceiveLifetime shall be the elapsed time in TU, after the initial reception of a fragmented MMPDU or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. The default value shall be 512.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnGlobalDot11aTIThreshold 1.3.6.1.4.1.14179.2.3.3.2.17
The Threshold being used to detect a busy medium (frequency). CCA shall report a busy medium upon detecting the RSSI above this threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aChannelAgilityEnabled 1.3.6.1.4.1.14179.2.3.3.2.18
This attribute indicates that the PHY channel agility functionality is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11hConfig 1.3.6.1.4.1.14179.2.3.4.1
OBJECT IDENTIFIER    

bsnGlobalDot11hPowerConstraint 1.3.6.1.4.1.14179.2.3.4.1.1
Local maximum transmit power for a channel is defined as maximum transmit power level specified for the channel in the Country element minus the local power constraint specified for the channel in the Power Constraint element.The power constraint is coded as an unsigned integer in units of decibels. To disable power constraint set Power Constraint to 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..30  

bsnGlobalDot11hChannelSwitchEnable 1.3.6.1.4.1.14179.2.3.4.1.2
To enable or disable channel switch. When disabling Channel Switch no need to pass mode and count
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11hChannelSwitchMode 1.3.6.1.4.1.14179.2.3.4.1.3
The Channel Switch Mode indicates any restriction on transmission until a channel switch. An Channel mode set to 1 means that the STA in a BSS to which the frame containing the element is addressed shall tranmit no further frames with in the BSS until the scheduled channel switch. A Channel switch mode set to 0 does not impose any requirement on the receiving STA.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRrmDot11a 1.3.6.1.4.1.14179.2.4.1
OBJECT IDENTIFIER    

bsnRrmDot11b 1.3.6.1.4.1.14179.2.4.2
OBJECT IDENTIFIER    

bsnRrmDot11aGroup 1.3.6.1.4.1.14179.2.4.1.1
OBJECT IDENTIFIER    

bsnRrmDot11aGlobalAutomaticGrouping 1.3.6.1.4.1.14179.2.4.1.1.1
Dynamic grouping has two modes: on and off. When the grouping is off, no dynamic grouping occurs. Each Airespace Switch optimizes only its own Airespace APs' parameters. When grouping is on, the Airespace Switches form groups and elect leaders to perform better dynamic parameter optimization.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER automatic(1), off(2)  

bsnRrmDot11aGroupLeaderMacAddr 1.3.6.1.4.1.14179.2.4.1.1.2
This is the MAC address of the group leader for the dot11a group containing this Airespace Switch.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnRrmIsDot11aGroupLeader 1.3.6.1.4.1.14179.2.4.1.1.3
If this Airespace Switch is a Dot11a Group Leader then this attribute will be true else it will be false.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnRrmDot11aGroupLastUpdateTime 1.3.6.1.4.1.14179.2.4.1.1.4
Last time the dot11a grouping was updated on this Airespace Switch. This is valid only if the Airespace Switch is a group leader.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnRrmDot11aGlobalGroupInterval 1.3.6.1.4.1.14179.2.4.1.1.5
When grouping is on, this interval(in secs) represents the period with which the grouping algorithm is run. Grouping algorithm will also run when the group contents changes and the automatic grouping is enabled. A dynamic grouping can be started upon request from the system administrator. Default value is 3600 secs.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnWrasDot11aGroupTable 1.3.6.1.4.1.14179.2.4.1.1.9
This is a table of Airespace Switch addresses that identifies the members of the Dot11a RF group containing this Airespace Switch. Max size is 20 entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnWrasDot11aGroupEntry

bsnWrasDot11aGroupEntry 1.3.6.1.4.1.14179.2.4.1.1.9.1
...
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnWrasDot11aGroupEntry  

bsnWrasDot11aPeerMacAddress 1.3.6.1.4.1.14179.2.4.1.1.9.1.1
The MAC address of the member Switch.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnWrasDot11aPeerIpAddress 1.3.6.1.4.1.14179.2.4.1.1.9.1.21
The IP address of the Airespace Switch.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bsnRrmDot11aAPDefault 1.3.6.1.4.1.14179.2.4.1.6
OBJECT IDENTIFIER    

bsnRrmDot11aForeignInterferenceThreshold 1.3.6.1.4.1.14179.2.4.1.6.1
foreign 802.11A interference threshold between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11aForeignNoiseThreshold 1.3.6.1.4.1.14179.2.4.1.6.2
802.11A foreign noise threshold between -127 and 0 dBm.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -127..0  

bsnRrmDot11aRFUtilizationThreshold 1.3.6.1.4.1.14179.2.4.1.6.3
802.11A RF utlization threshold between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11aThroughputThreshold 1.3.6.1.4.1.14179.2.4.1.6.4
802.11A throughput threshold between 1000 and 100000
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..1000000  

bsnRrmDot11aMobilesThreshold 1.3.6.1.4.1.14179.2.4.1.6.5
802.11A mobiles threshold between 1 and 75
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..75  

bsnRrmDot11aCoverageThreshold 1.3.6.1.4.1.14179.2.4.1.6.6
802.11A coverage threshold between 3 and 50.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 3..50  

bsnRrmDot11aMobileMinExceptionLevel 1.3.6.1.4.1.14179.2.4.1.6.7
802.11A mobile minimum exception level between 1 and 75
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..75  

bsnRrmDot11aCoverageExceptionLevel 1.3.6.1.4.1.14179.2.4.1.6.8
802.11A coverage exception level between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11aSignalMeasurementInterval 1.3.6.1.4.1.14179.2.4.1.6.9
This interval (in secs) specifies how often do we get new signal strength measurements at each Airespace AP. Default is 300 secs
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11aNoiseMeasurementInterval 1.3.6.1.4.1.14179.2.4.1.6.10
This interval( in secs) specifies how often do we get new noise and interference measurements at each Airespace AP. Default is 300 secs
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11aLoadMeasurementInterval 1.3.6.1.4.1.14179.2.4.1.6.11
This interval( in secs) specifies how often do we get new load measurements at each Airespace AP. Default is 300 secs
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11aCoverageMeasurementInterval 1.3.6.1.4.1.14179.2.4.1.6.12
This interval( in secs) specifies how often do we get new coverage measurements at each Airespace AP. Default is 300 secs
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11aChannelMonitorList 1.3.6.1.4.1.14179.2.4.1.6.13
This attribute specifies the channels on which the switch monitors noise, interference and rogues. The first option allows monitoring on all channels while the second one on only those that are supported by the country of operation. the option dca implies that the monitor channel list will include those channels that are used by automatic channel assignment.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), country(2), dca(3)  

bsnRrmDot11aSetFactoryDefault 1.3.6.1.4.1.14179.2.4.1.7
When set to activate all rrm parameters are reset to factory defaults
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnRrmDot11bGroup 1.3.6.1.4.1.14179.2.4.2.1
OBJECT IDENTIFIER    

bsnRrmDot11bGlobalAutomaticGrouping 1.3.6.1.4.1.14179.2.4.2.1.1
Dynamic grouping has two modes: on and off. When the grouping is off, no dynamic grouping occurs. Each Airespace Switch optimizes only its own Airespace APs' parameters. When grouping is on, the Airespace Switchs form groups and elect leaders to perform better dynamic parameter optimization.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER automatic(1), off(2)  

bsnRrmDot11bGroupLeaderMacAddr 1.3.6.1.4.1.14179.2.4.2.1.2
This is the MAC address of the group leader for the dot11b group containing this Airespace Switch.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnRrmIsDot11bGroupLeader 1.3.6.1.4.1.14179.2.4.2.1.3
If this Airespace Switch is a Dot11b Group Leader then this attribute will be true else it will be false.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnRrmDot11bGroupLastUpdateTime 1.3.6.1.4.1.14179.2.4.2.1.4
Last time the dot11b grouping was updated on this Airespace Switch. This is valid only if the Airespace Switch is a group leader.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnRrmDot11bGlobalGroupInterval 1.3.6.1.4.1.14179.2.4.2.1.5
When grouping is on, this interval(in secs) represents the period with which the grouping algorithm is run. Grouping algorithm will also run when the group contents changes and the automatic grouping is enabled. A dynamic grouping can be started upon request from the system administrator. Default value is 3600 secs.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnWrasDot11bGroupTable 1.3.6.1.4.1.14179.2.4.2.1.9
This is a table of Airespace Switch addresses that identifies the members of the Dot11b RF group containing this Airespace Switch. Max size is 20 entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnWrasDot11bGroupEntry

bsnWrasDot11bGroupEntry 1.3.6.1.4.1.14179.2.4.2.1.9.1
...
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnWrasDot11bGroupEntry  

bsnWrasDot11bPeerMacAddress 1.3.6.1.4.1.14179.2.4.2.1.9.1.1
The MAC address of the GIGE interface.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnWrasDot11bPeerIpAddress 1.3.6.1.4.1.14179.2.4.2.1.9.1.21
The IP address of the Airespace Switch.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bsnRrmDot11bAPDefault 1.3.6.1.4.1.14179.2.4.2.6
OBJECT IDENTIFIER    

bsnRrmDot11bForeignInterferenceThreshold 1.3.6.1.4.1.14179.2.4.2.6.1
Foreign 802.11A interference threshold between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11bForeignNoiseThreshold 1.3.6.1.4.1.14179.2.4.2.6.2
802.11A foreign noise threshold between -127 and 0 dBm.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -127..0  

bsnRrmDot11bRFUtilizationThreshold 1.3.6.1.4.1.14179.2.4.2.6.3
802.11A RF utlization threshold between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11bThroughputThreshold 1.3.6.1.4.1.14179.2.4.2.6.4
802.11A Airespace AP data-rate threshold between 1000 and 100000
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..1000000  

bsnRrmDot11bMobilesThreshold 1.3.6.1.4.1.14179.2.4.2.6.5
802.11A Airespace AP mobiles threshold between 1 and 75
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..75  

bsnRrmDot11bCoverageThreshold 1.3.6.1.4.1.14179.2.4.2.6.6
802.11A Airespace AP coverage threshold between 3 and 50.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 3..50  

bsnRrmDot11bMobileMinExceptionLevel 1.3.6.1.4.1.14179.2.4.2.6.7
802.11A Airespace AP mobile minimum exception level between 1 and 75
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..75  

bsnRrmDot11bCoverageExceptionLevel 1.3.6.1.4.1.14179.2.4.2.6.8
802.11A Airespace AP coverage exception level between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11bSignalMeasurementInterval 1.3.6.1.4.1.14179.2.4.2.6.9
This interval( in secs) specifies how often do we get new signal strength measurements at each Airespace AP. Default is 300 secs
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11bNoiseMeasurementInterval 1.3.6.1.4.1.14179.2.4.2.6.10
This interval( in secs) specifies how often do we get new noise and interference measurements at each Airespace AP. Default is 300 secs
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11bLoadMeasurementInterval 1.3.6.1.4.1.14179.2.4.2.6.11
This interval( in secs) specifies how often do we get new load measurements at each Airespace AP. Default is 300 secs
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11bCoverageMeasurementInterval 1.3.6.1.4.1.14179.2.4.2.6.12
This interval( in secs) specifies how often do we get new coverage measurements at each Airespace AP. Default is 300 secs
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 10..3600  

bsnRrmDot11bChannelMonitorList 1.3.6.1.4.1.14179.2.4.2.6.13
This attribute specifies the channels on which the switch monitors noise, interference and rogues. The first option allows monitoring on all channels while the second one on only those that are supported by the country of operation. the option dca implies that the monitor channel list will include those channels that are used by automatic channel assignment.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), country(2), dca(3)  

bsnRrmDot11bSetFactoryDefault 1.3.6.1.4.1.14179.2.4.2.7
When set to activate all rrm parameters are reset to factory defaults
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnRadiusAuthServerTable 1.3.6.1.4.1.14179.2.5.1
The (conceptual) table listing the RADIUS authentication servers with which the client shares a secret.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRadiusAuthServerEntry

bsnRadiusAuthServerEntry 1.3.6.1.4.1.14179.2.5.1.1
An entry (conceptual row) representing a RADIUS authentication server with which the client shares a secret.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnRadiusAuthServerEntry  

bsnRadiusAuthServerIndex 1.3.6.1.4.1.14179.2.5.1.1.1
A number uniquely identifying each RADIUS Authentication server with which this client communicates.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..17  

bsnRadiusAuthServerAddress 1.3.6.1.4.1.14179.2.5.1.1.2
The IP address of the RADIUS authentication server referred to in this table entry.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnRadiusAuthClientServerPortNumber 1.3.6.1.4.1.14179.2.5.1.1.3
The UDP port the client is using to send requests to this server.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

bsnRadiusAuthServerKey 1.3.6.1.4.1.14179.2.5.1.1.4
The authentication and encryption key shared between the Radius client and this Radius Server. When the bsnRadiusAuthServerKeyFormat is hex it can have max length of 128 bytes. If the bsnRadiusAuthServerKeyFormat is Ascii it can have max length of 64 bytes.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

bsnRadiusAuthServerStatus 1.3.6.1.4.1.14179.2.5.1.1.5
Server enable or disable status.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAuthServerKeyFormat 1.3.6.1.4.1.14179.2.5.1.1.6
Format of the server key. When hex, the number of characters in the key should be even.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER hex(1), ascii(2)  

bsnRadiusAuthServerRFC3576 1.3.6.1.4.1.14179.2.5.1.1.7
Support for Dynamic Authorization Extensions to RADIUS.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAuthServerIPSec 1.3.6.1.4.1.14179.2.5.1.1.8
IPSec over RADIUS
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAuthServerIPSecAuth 1.3.6.1.4.1.14179.2.5.1.1.9
The Hash algorithm employed by the IPSec Encrpytion. This applies only when bsnRadiusAuthServerIPSec is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), hmacMd5(1), hmacSha1(2)  

bsnRadiusAuthServerIPSecEncryption 1.3.6.1.4.1.14179.2.5.1.1.10
The Encryption algorithm employed by this IpSec Encryption. This applies only when bsnRadiusAuthServerIPSec is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), des(1), tripleDes(2), aesCbc(3)  

bsnRadiusAuthServerIPSecIKEPhase1 1.3.6.1.4.1.14179.2.5.1.1.11
VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnRadiusAuthServerIPSec is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER main(1), agressive(2)  

bsnRadiusAuthServerIPSecIKELifetime 1.3.6.1.4.1.14179.2.5.1.1.12
IPSec IKE's Lifetime. This applies only when bsnRadiusAuthServerIPSec is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1800..345600  

bsnRadiusAuthServerIPSecDHGroup 1.3.6.1.4.1.14179.2.5.1.1.13
IKE's Diffie-Hellman Group. This applies only when bsnRadiusAuthServerIPSec is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER group1(1), group2(2), group5(5)  

bsnRadiusAuthServerNetworkUserConfig 1.3.6.1.4.1.14179.2.5.1.1.14
When enabled, this entry is considered as network user radius authenticating server entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAuthServerMgmtUserConfig 1.3.6.1.4.1.14179.2.5.1.1.15
When enabled, this entry is considered as management user radius authenticating server entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAuthServerRetransmitTimeout 1.3.6.1.4.1.14179.2.5.1.1.17
Time in seconds after which a radius authentication request will timeout and a retransmission will be taken up by the switch.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 2..30  

bsnRadiusAuthServerKeyWrapKEKkey 1.3.6.1.4.1.14179.2.5.1.1.18
Key-encryption-key (KEK) used as the key for the 128 bit AES Key Wrap algorithm to encrypt the PMK in the key attribute. If the key is present in request, it should be taken as a hint by the server that the sender prefers this method of encryption over others. To maintain security actual keys after configuration are never returned in get request. If keys are configured then '***' is returned. If keys are not configured then empty string is retunred. bsnRadiusAuthServerKeyFormat is used this key. if the format chosen is ascii then it should be 16 bytes in length. if the format chosen is hex then it should be 32 bytes in length.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

bsnRadiusAuthServerKeyWrapMACKkey 1.3.6.1.4.1.14179.2.5.1.1.19
Message-authenticator-code-key ( MACK) - used as the key for the HMAC-SHA-1 algorithm to sign the RADIUS message to prevent spoofing. MACK must be configured when KEK is configured. To maintain security actual keys after configuration are never returned in get request. If keys are configured then '***' is returned. If keys are not configured then empty string is returned. bsnRadiusAuthServerKeyFormat is used this key. if the format chosen is ascii then it should be 20 bytes in length. If the format chosen is hex then it should be 40 bytes in length.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

bsnRadiusAuthServerKeyWrapFormat 1.3.6.1.4.1.14179.2.5.1.1.20
Format for the Key Wrap keys. This object is mandatory for manager to send if the key Wrap keys are being configured. Get on this object will always return hex(1)
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER hex(1), ascii(2)  

bsnRadiusAuthServerRowStatus 1.3.6.1.4.1.14179.2.5.1.1.26
Row Status for creation/deletion
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnRadiusAccServerTable 1.3.6.1.4.1.14179.2.5.2
The (conceptual) table listing the RADIUS accounting servers with which the client shares a secret.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRadiusAccServerEntry

bsnRadiusAccServerEntry 1.3.6.1.4.1.14179.2.5.2.1
An entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnRadiusAccServerEntry  

bsnRadiusAccServerIndex 1.3.6.1.4.1.14179.2.5.2.1.1
A number uniquely identifying each RADIUS Accounting server with which this client communicates.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..17  

bsnRadiusAccServerAddress 1.3.6.1.4.1.14179.2.5.2.1.2
The IP address of the RADIUS accounting server referred to in this table entry.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnRadiusAccClientServerPortNumber 1.3.6.1.4.1.14179.2.5.2.1.3
The UDP port the client is using to send requests to this server.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

bsnRadiusAccServerKey 1.3.6.1.4.1.14179.2.5.2.1.4
The authentication and encryption key shared between the Radius client and this Radius Server. When the bsnRadiusAccServerKeyFormat is hex it can have max length of 128 bytes. If the bsnRadiusAccServerKeyFormat is Ascii it can have max length of 64 bytes.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

bsnRadiusAccServerStatus 1.3.6.1.4.1.14179.2.5.2.1.5
Server enable or disable status.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAccServerKeyFormat 1.3.6.1.4.1.14179.2.5.2.1.6
Format of the server key. When hex, the number of characters in the key should be even.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER hex(1), ascii(2)  

bsnRadiusAccServerIPSec 1.3.6.1.4.1.14179.2.5.2.1.7
IPSec over RADIUS
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAccServerIPSecAuth 1.3.6.1.4.1.14179.2.5.2.1.8
The Hash algorithm employed by the IPSec Encrpytion. This applies only when bsnRadiusAccServerIPSec is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), hmacMd5(1), hmacSha1(2)  

bsnRadiusAccServerIPSecEncryption 1.3.6.1.4.1.14179.2.5.2.1.9
The Encryption algorithm employed by this IpSec Encryption. This applies only when bsnRadiusAccServerIPSec is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), des(1), tripleDes(2), aesCbc(3)  

bsnRadiusAccServerIPSecIKEPhase1 1.3.6.1.4.1.14179.2.5.2.1.10
VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnRadiusAccServerIPSec is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER main(1), agressive(2)  

bsnRadiusAccServerIPSecIKELifetime 1.3.6.1.4.1.14179.2.5.2.1.11
IPSec IKE's Lifetime. This applies only when bsnRadiusAccServerIPSec is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1800..345600  

bsnRadiusAccServerIPSecDHGroup 1.3.6.1.4.1.14179.2.5.2.1.12
IKE's Diffie-Hellman Group. This applies only when bsnRadiusAccServerIPSec is in enable state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER group1(1), group2(2), group5(5)  

bsnRadiusAccServerNetworkUserConfig 1.3.6.1.4.1.14179.2.5.2.1.13
When enabled, this entry is considered as network user radius accounting server entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAccServerRetransmitTimeout 1.3.6.1.4.1.14179.2.5.2.1.14
Time in seconds after which a radius accounting request will timeout and a retransmission will be taken up by the switch.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 2..30  

bsnRadiusAccServerRowStatus 1.3.6.1.4.1.14179.2.5.2.1.26
Row Status for creation/deletion
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnRadiusAuthServerStatsTable 1.3.6.1.4.1.14179.2.5.3
The listing the Statistics of RADIUS authentication servers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRadiusAuthServerStatsEntry

bsnRadiusAuthServerStatsEntry 1.3.6.1.4.1.14179.2.5.3.1
An entry representing statistics a RADIUS authentication server with which the client shares a secret.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnRadiusAuthServerStatsEntry  

bsnRadiusAuthClientRoundTripTime 1.3.6.1.4.1.14179.2.5.3.1.6
The time interval (in hundredths of a second) between the most recent Access-Reply/Access-Challenge and the Access-Request that matched it from this RADIUS authentication server.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

bsnRadiusAuthClientAccessRequests 1.3.6.1.4.1.14179.2.5.3.1.7
The number of RADIUS Access-Request packets sent to this server. This does not include retransmissions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientAccessRetransmissions 1.3.6.1.4.1.14179.2.5.3.1.8
The number of RADIUS Access-Request packets retransmitted to this RADIUS authentication server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientAccessAccepts 1.3.6.1.4.1.14179.2.5.3.1.9
The number of RADIUS Access-Accept packets (valid or invalid) received from this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientAccessRejects 1.3.6.1.4.1.14179.2.5.3.1.10
The number of RADIUS Access-Reject packets (valid or invalid) received from this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientAccessChallenges 1.3.6.1.4.1.14179.2.5.3.1.11
The number of RADIUS Access-Challenge packets (valid or invalid) received from this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientMalformedAccessResponses 1.3.6.1.4.1.14179.2.5.3.1.12
The number of malformed RADIUS Access-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators or Signature attributes or unknown types are not included as malformed access responses.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientBadAuthenticators 1.3.6.1.4.1.14179.2.5.3.1.13
The number of RADIUS Access-Response packets containing invalid authenticators or Signature attributes received from this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientPendingRequests 1.3.6.1.4.1.14179.2.5.3.1.14
The number of RADIUS Access-Request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an Access-Request is sent and decremented due to receipt of an Acess-Accept, Access-Reject or Access-Challenge, a timeout or retransmission.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

bsnRadiusAuthClientTimeouts 1.3.6.1.4.1.14179.2.5.3.1.15
The number of authentication timeouts to this server. After a timeout the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as a Request as well as a timeout.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientUnknownTypes 1.3.6.1.4.1.14179.2.5.3.1.16
The number of RADIUS packets of unknown type which were received from this server on the authentication port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientPacketsDropped 1.3.6.1.4.1.14179.2.5.3.1.36
The number of RADIUS packets of which were received from this server on the authentication port and dropped for some other reason.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAccServerStatsTable 1.3.6.1.4.1.14179.2.5.4
The (conceptual) table listing the RADIUS accounting servers with which the client shares a secret.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRadiusAccServerStatsEntry

bsnRadiusAccServerStatsEntry 1.3.6.1.4.1.14179.2.5.4.1
An entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnRadiusAccServerStatsEntry  

bsnRadiusAccClientRoundTripTime 1.3.6.1.4.1.14179.2.5.4.1.6
The time interval between the most recent Accounting-Response and the Accounting-Request that matched it from this RADIUS accounting server.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

bsnRadiusAccClientRequests 1.3.6.1.4.1.14179.2.5.4.1.7
The number of RADIUS Accounting-Request packets sent. This does not include retransmissions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientRetransmissions 1.3.6.1.4.1.14179.2.5.4.1.8
The number of RADIUS Accounting-Request packets retransmitted to this RADIUS accounting server. Retransmissions include retries where the Identifier and Acct-Delay have been updated, as well as those in which they remain the same.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientResponses 1.3.6.1.4.1.14179.2.5.4.1.9
The number of RADIUS packets received on the accounting port from this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientMalformedResponses 1.3.6.1.4.1.14179.2.5.4.1.10
The number of malformed RADIUS Accounting-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators and unknown types are not included as malformed accounting responses.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientBadAuthenticators 1.3.6.1.4.1.14179.2.5.4.1.11
The number of RADIUS Accounting-Response packets which contained invalid authenticators received from this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientPendingRequests 1.3.6.1.4.1.14179.2.5.4.1.12
The number of RADIUS Accounting-Request packets sent to this server that have not yet timed out or received a response. This variable is incremented when an Accounting-Request is sent and decremented due to receipt of an Accounting-Response, a timeout or a retransmission.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

bsnRadiusAccClientTimeouts 1.3.6.1.4.1.14179.2.5.4.1.13
The number of accounting timeouts to this server. After a timeout the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as an Accounting-Request as well as a timeout.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientUnknownTypes 1.3.6.1.4.1.14179.2.5.4.1.14
The number of RADIUS packets of unknown type which were received from this server on the accounting port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientPacketsDropped 1.3.6.1.4.1.14179.2.5.4.1.34
The number of RADIUS packets which were received from this server on the accounting port and dropped for some other reason.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnUsersTable 1.3.6.1.4.1.14179.2.5.5
The (conceptual) table listing Wlan Users
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnUsersEntry

bsnUsersEntry 1.3.6.1.4.1.14179.2.5.5.1
....
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  BsnUsersEntry  

bsnUserName 1.3.6.1.4.1.14179.2.5.5.1.2
User Name
Status: obsolete Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..24)  

bsnUserPassword 1.3.6.1.4.1.14179.2.5.5.1.3
User Password
Status: obsolete Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..24)  

bsnUserEssIndex 1.3.6.1.4.1.14179.2.5.5.1.4
User WLAN ID. Value 0 implies that this applies to any WLAN ID.
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER 0..517  

bsnUserAccessMode 1.3.6.1.4.1.14179.2.5.5.1.5
User Access Mode.
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER readOnly(1), readWrite(2)  

bsnUserType 1.3.6.1.4.1.14179.2.5.5.1.6
User Type.
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER management(1), wlan(2), macFilter(3)  

bsnUserInterfaceName 1.3.6.1.4.1.14179.2.5.5.1.7
Interface Name.
Status: obsolete Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnUserRowStatus 1.3.6.1.4.1.14179.2.5.5.1.26
Row Status
Status: obsolete Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnMacFilterTable 1.3.6.1.4.1.14179.2.5.9
The table listing MAC Filter entries
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMacFilterEntry

bsnMacFilterEntry 1.3.6.1.4.1.14179.2.5.9.1
....
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMacFilterEntry  

bsnMacFilterAddress 1.3.6.1.4.1.14179.2.5.9.1.1
MAC Address of the entry
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..24)  

bsnMacFilterWlanId 1.3.6.1.4.1.14179.2.5.9.1.2
WLAN ID of the WLAN that the user can connect to. 0 means any WLAN ID.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..517  

bsnMacFilterInterfaceName 1.3.6.1.4.1.14179.2.5.9.1.3
Interface Name.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnMacFilterDescription 1.3.6.1.4.1.14179.2.5.9.1.4
Description of the MAC Filter entry.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnMacFilterRowStatus 1.3.6.1.4.1.14179.2.5.9.1.24
Row Status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnLocalNetUserTable 1.3.6.1.4.1.14179.2.5.10
The table listing Local Net User entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnLocalNetUserEntry

bsnLocalNetUserEntry 1.3.6.1.4.1.14179.2.5.10.1
....
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnLocalNetUserEntry  

bsnLocalNetUserName 1.3.6.1.4.1.14179.2.5.10.1.1
Name of the net user.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..24)  

bsnLocalNetUserWlanId 1.3.6.1.4.1.14179.2.5.10.1.2
WLAN ID of the WLAN that the user can connect to. 0 means any WLAN ID.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..517  

bsnLocalNetUserPassword 1.3.6.1.4.1.14179.2.5.10.1.3
User Password.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..24)  

bsnLocalNetUserDescription 1.3.6.1.4.1.14179.2.5.10.1.4
Description of the Net User entry.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnLocalNetUserLifetime 1.3.6.1.4.1.14179.2.5.10.1.5
This object indicates the lifetime of an user account expressed in hundredths of a second. Lifetime period other than 0 will make it a guest-user. Minimum value for guest user is 60 seconds (6000). Once configured as non-guest user can not be change to guest user and vice-versa. Default value is for a day and max lifetime is 259200000(30 days). WLANIds, which have webauth policy are valid for guest access user.
Status: current Access: read-create
OBJECT-TYPE    
  TimeInterval 0 | 6000..259200000  

bsnLocalNetUserStartTime 1.3.6.1.4.1.14179.2.5.10.1.6
This object indicates the time when the guest user account was created and expressed as the number of seconds elapsed since 1st Jan, 1970.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

bsnLocalNetUserRemainingTime 1.3.6.1.4.1.14179.2.5.10.1.7
This object indicates the remaining session time for the guest user in hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

bsnLocalNetUserRowStatus 1.3.6.1.4.1.14179.2.5.10.1.24
Row Status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnLocalManagementUserTable 1.3.6.1.4.1.14179.2.5.11
The (conceptual) table listing Local Management Users
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnLocalManagementUserEntry

bsnLocalManagementUserEntry 1.3.6.1.4.1.14179.2.5.11.1
....
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnLocalManagementUserEntry  

bsnLocalManagementUserName 1.3.6.1.4.1.14179.2.5.11.1.1
User Name
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..24)  

bsnLocalManagementUserPassword 1.3.6.1.4.1.14179.2.5.11.1.2
User Password
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..24)  

bsnLocalManagementUserAccessMode 1.3.6.1.4.1.14179.2.5.11.1.3
User Access Mode.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER readOnly(1), readWrite(2)  

bsnLocalManagementUserRowStatus 1.3.6.1.4.1.14179.2.5.11.1.23
Row Status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnAclTable 1.3.6.1.4.1.14179.2.5.7
The table listing ACLs (Access Control Lists) on the Switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAclEntry

bsnAclEntry 1.3.6.1.4.1.14179.2.5.7.1
....
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAclEntry  

bsnAclName 1.3.6.1.4.1.14179.2.5.7.1.1
Name of the Access Control List.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

bsnAclApplyMode 1.3.6.1.4.1.14179.2.5.7.1.2
The apply mode of the ACL on the switch. Mode value 'applied' means the ACL has been applied on the switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notapplied(0), applied(1)  

bsnAclRowStatus 1.3.6.1.4.1.14179.2.5.7.1.20
Row Status of the ACL.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnAclRuleTable 1.3.6.1.4.1.14179.2.5.8
The table listing Acl Rules(Access Control List Entries) on the ACL with name bsnAclName.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAclRuleEntry

bsnAclRuleEntry 1.3.6.1.4.1.14179.2.5.8.1
....
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAclRuleEntry  

bsnAclRuleIndex 1.3.6.1.4.1.14179.2.5.8.1.2
Index of the ACL rule. This can be updated to reset the sequence of the rules of an ACL.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..64  

bsnAclRuleAction 1.3.6.1.4.1.14179.2.5.8.1.3
The permission mode of a rule.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER deny(0), permit(1)  

bsnAclRuleDirection 1.3.6.1.4.1.14179.2.5.8.1.4
The direction of the packet to which the rule may be applied.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER inbound(0), outbound(1), any(2)  

bsnAclRuleSourceIpAddress 1.3.6.1.4.1.14179.2.5.8.1.5
Source IP Address of the ACL rule. A value 0 implies any source address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnAclRuleSourceIpNetmask 1.3.6.1.4.1.14179.2.5.8.1.6
Source IP Netmask of the ACL rule. A value 0 implies any source mask.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnAclRuleDestinationIpAddress 1.3.6.1.4.1.14179.2.5.8.1.7
Destination IP Address of the ACL rule. A value 0 implies any destination address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnAclRuleDestinationIpNetmask 1.3.6.1.4.1.14179.2.5.8.1.8
Destination Netmask of the ACL rule. A value 0 implies any destination mask.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnAclRuleProtocol 1.3.6.1.4.1.14179.2.5.8.1.9
Protocol of the packet. It can be either of the pre specified protocols like TCP, UDP, ICMP, ESP, AH, GRE, IP, Ethernet Over IP, OSPF or any number between 0 and 255. A value 256 implies that this rule applies to 'Any' protocol.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..256  

bsnAclRuleStartSourcePort 1.3.6.1.4.1.14179.2.5.8.1.10
Source Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any' source port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnAclRuleEndSourcePort 1.3.6.1.4.1.14179.2.5.8.1.11
Source Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any' source port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnAclRuleStartDestinationPort 1.3.6.1.4.1.14179.2.5.8.1.12
Destination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule aplpies to 'Any' Destination port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnAclRuleEndDestinationPort 1.3.6.1.4.1.14179.2.5.8.1.13
Destination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule aplpies to 'Any' Destination port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnAclRuleDscp 1.3.6.1.4.1.14179.2.5.8.1.14
DSCP value of the rule. A value 256 implies Any
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..256  

bsnAclNewRuleIndex 1.3.6.1.4.1.14179.2.5.8.1.15
New Index of the ACL rule. This attribute should be updated if the requirement is to reset the sequence of the rules of an ACL. A read on this will not yield anything.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..64  

bsnAclRuleRowStatus 1.3.6.1.4.1.14179.2.5.8.1.40
Row Status of the ACL Rule.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnRadiusAuthKeyWrapEnable 1.3.6.1.4.1.14179.2.5.12
When keyWrap is enable then for 801.1X and 802.11i client Authentication, request is sent to those radius servers which has KEK and MACK keys are configured. Radius servers are widely used for user authentications. In 802.11i and 802.1X type authentication, the controller recives Pairwise Master KEy(PMK) from RADIUS sever using vendor specific RADIUS attributes, which uses MPPE RFC3078. Since MPPE uses RC4 algorithm to provide data confidentiality, it is not FIPS approved. For this RADIUS key WRAP attributes, bsnRadiusAuthServerKeyWrap and bsnRadiusAuthServerKeyWrapMACKkey have been added, which are used to securely transfer encryption keys using non-proprietary techniques.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

bsnRadiusAuthCacheCredentialsLocally 1.3.6.1.4.1.14179.2.5.14
Enable or disable caching of credentials locally for RADIUS Auth servers. This is used when a client uses a one time password authentication scheme.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAAAMacDelimiter 1.3.6.1.4.1.14179.2.5.15
The delimiter to be used for mac filtering. It can be colon as in xx:xx:xx:xx:xx:xx or hyphen as in xx-xx-xx-xx-xx-xx or single hyphen as in xxxxxx-xxxxxx or no delimiter as in xxxxxxxxxxxx.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noDelimiter(0), colon(1), hyphen(2), singleHyphen(3)  

bsnAAARadiusCompatibilityMode 1.3.6.1.4.1.14179.2.5.16
The required compatibility mode for MAC filtering. For ciscoACS, the expected MAC delimiter setting is colon and for orinocoRadius, it is singleHyphen.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ciscoACS(0), orinocoRadius(1), other(2)  

bsnAAARadiusCallStationIdType 1.3.6.1.4.1.14179.2.5.17
This attribute configures the call station ID information sent in RADIUS messages. The value undefined cannot be set during the write operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ipAddr(0), macAddr(1), apMacAddress(2)  

bsnAAALocalDatabaseSize 1.3.6.1.4.1.14179.2.5.20
This attribute is the total number of entries permitted in the local users database. This is the combined total of entries for Local Management Users, Local Net Users, Disabled Clients (previously known as blacklistclients and the MAC Filters. If the database size limit is reached, no more entries in any of these user lists are allowed to be created. To continue creating more entries, one should increase the size of the database. This value is applied on reboot and then matches the bsnAACurrentLocalDatabaseSize.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 512..2048  

bsnAAACurrentLocalDatabaseSize 1.3.6.1.4.1.14179.2.5.21
This attribute is the maximum number of entries in the local users database that is effective currently. This is the combined total of entries for Local Management Users, Local Net Users, Disabled Clients (previously known as blacklist clients) and the MAC Filters.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 512..2048  

bsnBlackListClientTable 1.3.6.1.4.1.14179.2.5.6
The table listing Wlan Black Listed Clients
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnBlackListClientEntry

bsnBlackListClientEntry 1.3.6.1.4.1.14179.2.5.6.1
....
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnBlackListClientEntry  

bsnBlackListClientMacAddress 1.3.6.1.4.1.14179.2.5.6.1.1
Black Listed Client MAC Address
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..12)  

bsnBlackListClientDescription 1.3.6.1.4.1.14179.2.5.6.1.2
Black Listed Client Description
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnBlackListClientRowStatus 1.3.6.1.4.1.14179.2.5.6.1.22
Row Status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnExternalPolicyServerTable 1.3.6.1.4.1.14179.2.5.19
The (conceptual) table listing the External Policy servers with which client share a secret.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnExternalPolicyServerEntry

bsnExternalPolicyServerEntry 1.3.6.1.4.1.14179.2.5.19.1
An entry (conceptual row) representing an External policy server with which the client shares a secret.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  BsnExternalPolicyServerEntry  

bsnExternalPolicyServerIndex 1.3.6.1.4.1.14179.2.5.19.1.1
A number uniquely identifying each External Policy server with which this client communicates.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32 0..2  

bsnExternalPolicyServerAddress 1.3.6.1.4.1.14179.2.5.19.1.2
The IP address of the External Policy server referred to in this table entry.
Status: obsolete Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnExternalPolicyServerPortNumber 1.3.6.1.4.1.14179.2.5.19.1.3
The UDP port the client is using to send requests to this server.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

bsnExternalPolicyServerKey 1.3.6.1.4.1.14179.2.5.19.1.4
The authentication and encryption key shared between the client and this External Policy Server.
Status: obsolete Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

bsnExternalPolicyServerAdminStatus 1.3.6.1.4.1.14179.2.5.19.1.5
Server enable or disable status.
Status: obsolete Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnExternalPolicyServerConnectionStatus 1.3.6.1.4.1.14179.2.5.19.1.6
Server enable or disable status.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER disconnected(0), connected(1)  

bsnExternalPolicyServerRowStatus 1.3.6.1.4.1.14179.2.5.19.1.26
Row Status for creation/deletion
Status: obsolete Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnExternalPolicyServerAclName 1.3.6.1.4.1.14179.2.5.18
This attribute configures the ACL Name for External Policy Servers
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

bsnAcceptSelfSignedCertificate 1.3.6.1.4.1.14179.2.3.1.48
This flag specifies if controller will accept Self Signed Certificate from AP as part of authorization.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnSystemClockTime 1.3.6.1.4.1.14179.2.3.1.49
This object represents the current clock time of the controller and expressed as the number of seconds elapsed since 00:00:00 on January 1, 1970, Coordinated Universal Time (UTC).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnAPAuthorizationTable 1.3.6.1.4.1.14179.2.5.22
The table listing AP Authorization entries
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPAuthorizationEntry

bsnAPAuthorizationEntry 1.3.6.1.4.1.14179.2.5.22.1
BsnAPAuthorizationEntry
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPAuthorizationEntry  

bsnAPAuthMacAddress 1.3.6.1.4.1.14179.2.5.22.1.1
MAC Address of the AP entry
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..24)  

bsnAPAuthCertificateType 1.3.6.1.4.1.14179.2.5.22.1.2
Supported certificate types are MIC, SSC (Self-Signed-Certificate) or no certificate.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER unknown(0), mic(1), ssc(2), locMic(3), locSsc(4), none(5)  

bsnAPAuthHashKey 1.3.6.1.4.1.14179.2.5.22.1.3
SHA1 hash key for SSC certificate validation. It has to be 40 hexa-decimal characters. This is considered when certificate type is SSC.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..40)  

bsnAPAuthRowStatus 1.3.6.1.4.1.14179.2.5.22.1.20
Row Status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnWrasIpsecCACertificate 1.3.6.1.4.1.14179.2.9.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..4096)  

bsnWrasIpsecCACertificateUpdate 1.3.6.1.4.1.14179.2.9.2
Note this attribute is for updating the certificate If you try to read it, it will always be ***
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..4096)  

bsnWrasIpsecCertTable 1.3.6.1.4.1.14179.2.9.3
A table of Certificates.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnWrasIpsecCertEntry

bsnWrasIpsecCertEntry 1.3.6.1.4.1.14179.2.9.3.1
Each entry contains a specific certificate.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnWrasIpsecCertEntry  

bsnWrasIpsecCertName 1.3.6.1.4.1.14179.2.9.3.1.1
The name assigned to this set of IKE Certificates.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..80)  

bsnWrasIpsecCertificateUpdate 1.3.6.1.4.1.14179.2.9.3.1.2
If you try to read this it will always be ***
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..4096)  

bsnWrasIpsecCertificate 1.3.6.1.4.1.14179.2.9.3.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..4096)  

bsnWrasIpsecCertPassword 1.3.6.1.4.1.14179.2.9.3.1.4
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..1500)  

bsnWrasIpsecCertStatus 1.3.6.1.4.1.14179.2.9.3.1.24
A row status type for the IKE Cert Entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnTrapControl 1.3.6.1.4.1.14179.2.6.1
OBJECT IDENTIFIER    

bsnTrapVariable 1.3.6.1.4.1.14179.2.6.2
OBJECT IDENTIFIER    

bsnTraps 1.3.6.1.4.1.14179.2.6.3
OBJECT IDENTIFIER    

bsnDot11StationTrapControlMask 1.3.6.1.4.1.14179.2.6.1.1
This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurence. Event corresponding value ----- ----------------- bsnDot11StationDisassociate 1 bsnDot11StationDeauthenticate 2 bsnDot11StationAuthenticateFail 4 bsnDot11StationAssociateFail 8 bsnDot11StationBlacklisted 16 bsnDot11StationAssociate 32 ciscoLwappDot11ClientMovedToRunState 64 By Default all bits are off.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnDot11StationDisassociate 1.3.6.1.4.1.14179.2.6.3.1
The disassociate notification shall be sent when the Station sends a Disassociation frame. The value of the notification shall include the MAC address of the MAC to which the Disassociation frame was sent and the reason for the disassociation
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnDot11StationDeauthenticate 1.3.6.1.4.1.14179.2.6.3.2
The deauthenticate notification shall be sent when the Station sends a Deauthentication frame. The value of the notification shall include the MAC address of the MAC to which the Deauthentication frame was sent and the reason for the deauthentication.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnDot11StationAuthenticateFail 1.3.6.1.4.1.14179.2.6.3.3
The authenticate failure notification shall be sent when the Station sends an Authentication frame with a status code other than 'successful'. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent and the reason for the authentication failure.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnDot11StationAssociateFail 1.3.6.1.4.1.14179.2.6.3.4
The associate failure notification shall be sent when the Station sends an Association frame with a status code other than 'successful'. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent and the reason for the authentication failure.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnDot11StationBlacklisted 1.3.6.1.4.1.14179.2.6.3.52
The station blacklisted notification shall be sent when the client is blacklisted. The reason could be repeated auth or association failures or IP Address theft. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent, the MAC and Slot Id of AP that client was associated to and the reason for black listing.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnDot11StationAssociate 1.3.6.1.4.1.14179.2.6.3.53
The associate notification shall be sent when any of the watchlisted clients(present on at least one watch list) associates with an AP. The value of the notification shall include the MAC address and the Slot ID of the radio to which the station Associated.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPTrapControlMask 1.3.6.1.4.1.14179.2.6.1.2
This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- bsnAPAssociate/Disassociate 1 bsnAPIfUp/Down 4 bsnAPAuthorizationFailureCause 16 By Default all bits are on.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnAPUp 1.3.6.1.4.1.14179.2.6.3.5
When Airespace AP operation status goes up this trap will be sent
Status: obsolete Access: read-write
NOTIFICATION-TYPE    

bsnAPDown 1.3.6.1.4.1.14179.2.6.3.6
When Airespace AP operation status goes down this trap will be sent
Status: obsolete Access: read-write
NOTIFICATION-TYPE    

bsnAPAssociated 1.3.6.1.4.1.14179.2.6.3.7
When Airespace AP Associates to a Airespace Switch, AP associated notification will be sent with dot3 MAC address of Airespace AP.This will help management system to discover Airespace AP and add to system.
Status: deprecated Access: read-write
NOTIFICATION-TYPE    

bsnAPDisassociated 1.3.6.1.4.1.14179.2.6.3.8
When Airespace AP disassociates from Airespace Switch, AP disassociated notification will be sent with dot3 MAC address of Airespace AP management system to remove Airespace AP from this Airespace Switch
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPIfUp 1.3.6.1.4.1.14179.2.6.3.9
When Airespace AP's interface's operation status goes up this trap will be sent
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPIfDown 1.3.6.1.4.1.14179.2.6.3.10
When Airespace AP's interface's operation status goes down this trap will be sent.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPProfileTrapControlMask 1.3.6.1.4.1.14179.2.6.1.3
This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- LoadProfileFail 1 NoiseProfileFail 2 InterferenceProfileFail 4 CoverageProfileFailed 8
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnAPLoadProfileFailed 1.3.6.1.4.1.14179.2.6.3.11
When LOAD Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPNoiseProfileFailed 1.3.6.1.4.1.14179.2.6.3.12
When Noise Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPInterferenceProfileFailed 1.3.6.1.4.1.14179.2.6.3.13
When Interference Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPMacAddrTrapVariable 1.3.6.1.4.1.14179.2.6.2.20
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

bsnAPNameTrapVariable 1.3.6.1.4.1.14179.2.6.2.21
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

bsnAPSlotIdTrapVariable 1.3.6.1.4.1.14179.2.6.2.22
Number of Radio Interfaces on the Airespace AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnAPChannelNumberTrapVariable 1.3.6.1.4.1.14179.2.6.2.23
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnAPCoverageThresholdTrapVariable 1.3.6.1.4.1.14179.2.6.2.24
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnAPCoverageFailedClients 1.3.6.1.4.1.14179.2.6.2.25
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnAPCoverageTotalClients 1.3.6.1.4.1.14179.2.6.2.26
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnClientMacAddr 1.3.6.1.4.1.14179.2.6.2.27
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

bsnClientRssi 1.3.6.1.4.1.14179.2.6.2.28
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnClientSnr 1.3.6.1.4.1.14179.2.6.2.29
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnInterferenceEnergyBeforeChannelUpdate 1.3.6.1.4.1.14179.2.6.2.30
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnInterferenceEnergyAfterChannelUpdate 1.3.6.1.4.1.14179.2.6.2.31
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnAPPortNumberTrapVariable 1.3.6.1.4.1.14179.2.6.2.32
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnAPPreviousChannelNumberTrapVariable 1.3.6.1.4.1.14179.2.6.2.83
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnAPReasonCodeTrapVariable 1.3.6.1.4.1.14179.2.6.2.84
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  BITS noReason(0), signal(1), noise(2), interference(3), load(4), radar(5), deviceAware(6), majorSIAQEvent(7)  

bsnNoiseBeforeChannelUpdate 1.3.6.1.4.1.14179.2.6.2.85
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnNoiseAfterChannelUpdate 1.3.6.1.4.1.14179.2.6.2.86
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnInterferenceBeforeChannelUpdate 1.3.6.1.4.1.14179.2.6.2.87
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnInterferenceAfterChannelUpdate 1.3.6.1.4.1.14179.2.6.2.88
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnAPCoverageProfileFailed 1.3.6.1.4.1.14179.2.6.3.14
When Coverage Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnAPLoadProfileUpdatedToPass 1.3.6.1.4.1.14179.2.6.3.37
When LOAD Profile state changes from FAIL to PASSt this notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnAPNoiseProfileUpdatedToPass 1.3.6.1.4.1.14179.2.6.3.38
When Noise Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnAPInterferenceProfileUpdatedToPass 1.3.6.1.4.1.14179.2.6.3.39
When Interference Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable /disable using bsnRrmProfileTrapControlFlag
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnAPCoverageProfileUpdatedToPass 1.3.6.1.4.1.14179.2.6.3.40
When Coverage Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnAPParamUpdateTrapControlMask 1.3.6.1.4.1.14179.2.6.1.4
Mac Parameters are updated for a Airespace AP interface whenever Dynamic Algorithm are run. This mask describes what update events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- TxPowerChange 1 ChannelChange 2 AntennaChange 4 RTSCTSThresholdChange 8 EDThresholdChange 16 FragmentationThresholdChange 32
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnAPCurrentTxPowerChanged 1.3.6.1.4.1.14179.2.6.3.15
Whenever dynamic algorithms are running and bsnAPIfPhyPowerAutomaticOn is true, Airespace AP Interface's CurrentTxPower might get updated by algorithm. When this occurs notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF along with the currentTxPower for this Airespace AP IF
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPCurrentChannelChanged 1.3.6.1.4.1.14179.2.6.3.16
Whenever dynamic algorithms are running and bsnAPIfPhyChannelAutomaticOn is true, Airespace AP Interface's CurrentChannel might get updated by algorithm. When this occurs notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF along with the currentChannel for this Airespace AP IF
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnRrmDot11aGroupingDone 1.3.6.1.4.1.14179.2.6.3.21
When Grouping is done, this notification will be sent from the previous Group Leader where grouping algorithm was run. It has MAC address of the new Group Leader.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnRrmDot11bGroupingDone 1.3.6.1.4.1.14179.2.6.3.22
When Grouping is done, this notification will be sent from the previous Group Leader where grouping algorithm was run. It has MAC address of the new Group Leader.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnConfigSaveTrapEnable 1.3.6.1.4.1.14179.2.6.1.9
If Rogue AP Detection and Removed Traps need to be sent
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnConfigSaved 1.3.6.1.4.1.14179.2.6.3.23
When configuration is save either from CLI or web interface This trap will be sent to inform NMS to do refresh
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnDot11EssCreated 1.3.6.1.4.1.14179.2.6.3.24
Whenever a new Ess (WLAN) is created, this notification will be sent along with EssIndex
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnDot11EssDeleted 1.3.6.1.4.1.14179.2.6.3.25
Whenever a Ess (WLAN)is deleted, this notification will be sent along with EssIndex
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAuthFailureUserName 1.3.6.1.4.1.14179.2.6.2.1
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnAuthFailureUserType 1.3.6.1.4.1.14179.2.6.2.2
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER mgmtUser(1), wlanUser(2), macFilter(3)  

bsnRADIUSServerTrapEnable 1.3.6.1.4.1.14179.2.6.1.7
if RADIUS Server Traps need to be sent
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAuthenticationFailureTrapEnable 1.3.6.1.4.1.14179.2.6.1.8
If Authentication Failure Traps need to be sent
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsn80211SecurityTrapControlMask 1.3.6.1.4.1.14179.2.6.1.10
This mask is for Security related trap controls. Event corresponding bit ----- ----------------- bsnWepKeyDecryptError 1 bsnSignatureAttackDetected 2 By Default all bits are off.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnWpsTrapControlEnable 1.3.6.1.4.1.14179.2.6.1.11
This control is for WPS(Wireless Intrusion Protection System) related traps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRADIUSServerNotResponding 1.3.6.1.4.1.14179.2.6.3.26
This trap is to indicate that no RADIUS server(s) are responding to authentication requests sent by the RADIUS client within the MWAR device(Switch).
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAuthenticationFailure 1.3.6.1.4.1.14179.2.6.3.27
This trap is to inform that client authentication failure has occured at MWAR(Switch). This could be cli/web user, wlan user, or Mac Authorized user. ServiceType will indicate which type of user it is and userName will be cli/web/wlan userName or MacAddress of Mac Authorized User
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnRemoteIPv4Address 1.3.6.1.4.1.14179.2.6.2.3
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

bsnIpsecErrorCount 1.3.6.1.4.1.14179.2.6.2.4
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnIpsecSPI 1.3.6.1.4.1.14179.2.6.2.5
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnRemoteUdpPort 1.3.6.1.4.1.14179.2.6.2.6
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..65535  

bsnIkeAuthMethod 1.3.6.1.4.1.14179.2.6.2.7
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnIkeTotalInitFailures 1.3.6.1.4.1.14179.2.6.2.8
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnIkeTotalInitNoResponses 1.3.6.1.4.1.14179.2.6.2.9
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnIkeTotalRespFailures 1.3.6.1.4.1.14179.2.6.2.10
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnNotifiesSent 1.3.6.1.4.1.14179.2.6.2.11
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnNotifiesReceived 1.3.6.1.4.1.14179.2.6.2.12
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnSuiteInitFailures 1.3.6.1.4.1.14179.2.6.2.13
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnSuiteRespondFailures 1.3.6.1.4.1.14179.2.6.2.14
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnInitiatorCookie 1.3.6.1.4.1.14179.2.6.2.15
The initiator cookie used in an ISAKMP message, to be associated with a trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(8)  

bsnResponderCookie 1.3.6.1.4.1.14179.2.6.2.16
The responder cookie used in an ISAKMP message, to be associated with a trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(8)  

bsnIsakmpInvalidCookies 1.3.6.1.4.1.14179.2.6.2.17
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnIpsecTrapsMask 1.3.6.1.4.1.14179.2.6.1.5
This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- bsnIpsecEspAuthFailureTrap 1 bsnIpsecEspReplayFailureTrap 2 bsnIpsecEspPolicyFailureTrap 4 bsnIpsecEspInvalidSpiTrap 8 bsnIpsecOtherPolicyFailureTrap 16 bsnIpsecIkeNegFailure 32 bsnIpsecSuiteNegFailure 64 bsnIpsecInvalidCookieTrap 128
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bsnIpsecEspAuthFailureTrap 1.3.6.1.4.1.14179.2.6.3.28
IPsec packets with invalid hashes were found in an inbound ESP SA. The total number of authentication errors accumulated is sent for the specific row of the ipsecSaEspInTable table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnIpsecEspReplayFailureTrap 1.3.6.1.4.1.14179.2.6.3.29
IPsec packets with invalid sequence numbers were found in an inbound ESP SA. The total number of replay errors accumulated is sent for the specific row of the ipsecSaEspInTable table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnIpsecEspInvalidSpiTrap 1.3.6.1.4.1.14179.2.6.3.31
A packet with an unknown SPI was detected from the specified peer with the specified SPI using the specified protocol. The destination address of the received packet is specified by ipsecLocalAddress. The value ifIndex may be 0 if this optional linkage is unsupported. If the object ipsecSecurityProtocol has the value for IPcomp, then the ipsecSPI object is the CPI of the packet. Implementations SHOULD send one trap per peer (within a reasonable time period), rather than sending one trap per packet.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnIpsecIkeNegFailure 1.3.6.1.4.1.14179.2.6.3.33
An attempt to negotiate a phase 1 IKE SA failed. The notification counts are also sent as part of the trap, along with the current value of the total negotiation error counters for ISAKMP.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnIpsecSuiteNegFailure 1.3.6.1.4.1.14179.2.6.3.34
An attempt to negotiate a phase 2 SA suite for the specified selector failed. The current total failure counts are passed as well as the notification type counts for the notify involved in the failure.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnIpsecInvalidCookieTrap 1.3.6.1.4.1.14179.2.6.3.35
ISAKMP packets with invalid cookies were detected from the specified source, intended for the specified destination. The initiator and responder cookies are also sent with the trap. The current count is sent to allow the trap to accurately relfect dropped and throttled traps. Implementations SHOULD send one trap per peer (within a reasonable time period, rather than sending one trap per packet.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnRogueAPTrapEnable 1.3.6.1.4.1.14179.2.6.1.6
If Rogue AP Detection and Removed Traps need to be sent
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRogueAPDetected 1.3.6.1.4.1.14179.2.6.3.36
When a Rogue AP is detected this Trap will be sent out along with APMacAddress on which its detected
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnRogueAPRemoved 1.3.6.1.4.1.14179.2.6.3.41
When a Rogue AP that was detected earlier no longer exists this Trap will be sent out along with APMacAddress on which its detected
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnRogueAPDetectedOnWiredNetwork 1.3.6.1.4.1.14179.2.6.3.59
When a Rogue is detected on the wired network this trap will be sent out. The same trap with bsnRogueAPOnWiredNetwork set to no will clear the previous trap.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnApHasNoRadioCards 1.3.6.1.4.1.14179.2.6.3.60
When an AP has no radio cards present on it, the switch sends this trap.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnDuplicateIpAddressReported 1.3.6.1.4.1.14179.2.6.3.61
This trap is issued when the switch or an AP detects another machine using its IP Address. The first variable has value yes if the duplicate IP is reported by an AP. In that case, the second attribute will carry the AP MAC Address. The third variable is the duplicate IP address in question and the last attribute is the MAC Address of the machine that is found to be using the duplicate IP.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPContainedAsARogue 1.3.6.1.4.1.14179.2.6.3.62
When our AP detects that it is being contained by another AP, this trap is issued. The clear flag is true if the AP is no longer being contained.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnNetworkStateChanged 1.3.6.1.4.1.14179.2.6.3.69
When the 802.11a or b/g network state is changed this trap is issued.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnSignatureAttackDetected 1.3.6.1.4.1.14179.2.6.3.70
This trap is sent out when a signature attack is detected by the switch. The standard and custom signatures are predefined on the switch (see bsnSignatureConfig group). The signatures also defines if its detection should be reported. The trap variables bsnSignatureName and bsnSignatureDescription are retrieved from the detected signature definition. Clear Trap Variable is turned on when the signature attack stops. The signature's quiet time configuration speicifes the time after which the clear trap would be sent. bsnSignatureMacInfo indicates whether the signature is used to track pattern matches for all source MAC addresses together or seperately for individual source MAC addresses. bsnSignatureAttackFrequency will carry the value for a specific MAC address or for all MAC addresses depending on bsnSignatureMacInfo.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPRadioCardTxFailure 1.3.6.1.4.1.14179.2.6.3.71
This trap is sent by the switch when a radio card on an AP stops transmitting.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPRadioCardTxFailureClear 1.3.6.1.4.1.14179.2.6.3.72
This trap is sent by the switch when a radio card on an AP starts transmitting again after a prior failure.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPRadioCardRxFailure 1.3.6.1.4.1.14179.2.6.3.73
This trap is sent by the switch when a radio card on an AP stops receiving.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPRadioCardRxFailureClear 1.3.6.1.4.1.14179.2.6.3.74
This trap is sent by the switch when a radio card on an AP starts receiving again after a prior failure.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPImpersonationDetected 1.3.6.1.4.1.14179.2.6.3.75
This trap is sent by the switch when a radio of an authenticated AP hears from another AP whose MAC Address neither matches that of a rogue's and nor is it an authenticated neighbor of the detecting AP.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnAPRegulatoryDomainMismatch 1.3.6.1.4.1.14179.2.6.3.79
This trap is generated if an AP's regulatory domain doesn't match the country the switch is configured for. Due to the mismatch, the AP will fail to associate with the Switch.
Status: deprecated Access: read-write
NOTIFICATION-TYPE    

bsnTrustedApHasInvalidPreamble 1.3.6.1.4.1.14179.2.6.3.76
Issued when a Trusted Rogue AP is auto contained for using invalid preamble. The second param is for the preamble used and the third param is for preamble required. If the clear variable has value true, then the trap clears the earlier alert.
Status: current Access: read-write
NOTIFICATION-TYPE    

bsnCurrentRadiosCount 1.3.6.1.4.1.14179.2.6.2.18
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnLicenseRadioCount 1.3.6.1.4.1.14179.2.6.2.19
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnMaxRogueCount 1.3.6.1.4.1.14179.2.6.2.33
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

bsnStationMacAddress 1.3.6.1.4.1.14179.2.6.2.34
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

bsnStationAPMacAddr 1.3.6.1.4.1.14179.2.6.2.35
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

bsnStationAPIfSlotId 1.3.6.1.4.1.14179.2.6.2.36
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER 0..15  

bsnStationReasonCode 1.3.6.1.4.1.14179.2.6.2.37
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER unspecified(1), previousAuthNotValid(2), deauthenticationLeaving(3), disassociationDueToInactivity(4), disassociationAPBusy(5), class2FrameFromNonAuthStation(6), class2FrameFromNonAssStation(7), disassociationStaHasLeft(8), staReqAssociationWithoutAuth(9), invalidInformationElement(40), groupCipherInvalid(41), unicastCipherInvalid(42), akmpInvalid(43), unsupportedRsnVersion(44), invalidRsnIeCapabilities(45), cipherSuiteRejected(46), missingReasonCode(99)  

bsnStationBlacklistingReasonCode 1.3.6.1.4.1.14179.2.6.2.38
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER failed80211Auth(1), failedAssociation(2), ipTheft(3), failed8021xAuth(4), failedWebAuth(5)  

bsnStationUserName 1.3.6.1.4.1.14179.2.6.2.39
The user name of a client. This is used for the Client Associated trap. It may be null when not known.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

bsnRogueAPOnWiredNetwork 1.3.6.1.4.1.14179.2.6.2.40
This is the flag used on the bsnRogueAPDetected trap to state if the rogue is found on the wired network. Typically, after a rogue is found, there may be another bsnRogueAPDetected trap that will have the value of this flag 1 if the rogue is detected on the wired network.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnNavDosAttackSourceMacAddr 1.3.6.1.4.1.14179.2.6.2.41
MAC address generating the attack.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

bsnWlanIdTrapVariable 1.3.6.1.4.1.14179.2.6.2.42
WLAN ID used by the client when the WPA MIC error counter measure was activated.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER 1..517  

bsnUserIpAddress 1.3.6.1.4.1.14179.2.6.2.43
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

bsnRogueAdhocMode 1.3.6.1.4.1.14179.2.6.2.44
This is the flag used on the bsnRogueAPDetected trap to state if the rogue found is an Adhoc rogue or it is an AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnClearTrapVariable 1.3.6.1.4.1.14179.2.6.2.45
This is the flag is used to indicate if this is a clear trap for the original alert or not.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER false(0), true(1)  

bsnDuplicateIpTrapVariable 1.3.6.1.4.1.14179.2.6.2.46
This field is used on the bsnDuplicateIpAddressReported trap to contain the IP Address in question when switch or an AP detected a duplicate IP Address on another machine.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

bsnDuplicateIpTrapClear 1.3.6.1.4.1.14179.2.6.2.47
This is the flag used to indicate clear state for the bsnDuplicateIpAddressReported trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER false(0), true(1)  

bsnDuplicateIpReportedByAP 1.3.6.1.4.1.14179.2.6.2.48
This is the flag used on the bsnDuplicateIpAddressReported trap to indicate whether the switch or an AP detected a duplicate IP Address on another machine.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnTrustedApRadioPolicyRequired 1.3.6.1.4.1.14179.2.6.2.49
This is the radio policy required by a trusted Rogue.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER none(0), dot11b(1), dot11a(2), dot11bg(3)  

bsnTrustedApEncryptionUsed 1.3.6.1.4.1.14179.2.6.2.50
This is the encryption type used by a trusted Rogue.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER none(0), open(1), wep(2), wpa(3)  

bsnTrustedApEncryptionRequired 1.3.6.1.4.1.14179.2.6.2.51
This is the encryption type required by a trusted Rogue.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER none(0), open(1), wep(2), wpa(3)  

bsnTrustedApRadioPolicyUsed 1.3.6.1.4.1.14179.2.6.2.52
This is the radio policy used by a trusted Rogue.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER none(0), dot11b(1), dot11a(2), dot11bg(3)  

bsnNetworkType 1.3.6.1.4.1.14179.2.6.2.53
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2)  

bsnNetworkState 1.3.6.1.4.1.14179.2.6.2.54
Tok_String
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnSignatureType 1.3.6.1.4.1.14179.2.6.2.55
Type of Signature whose attack is detected by the switch.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER standard(0), custom(1)  

bsnSignatureName 1.3.6.1.4.1.14179.2.6.2.56
Name of the Signature whose attack is detected by the switch.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..20)  

bsnSignatureDescription 1.3.6.1.4.1.14179.2.6.2.57
Description of the Signature whose attack is detected by the switch.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..100)  

bsnImpersonatedAPMacAddr 1.3.6.1.4.1.14179.2.6.2.58
MAC Address of the AP impersonated by another AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

bsnTrustedApPreambleUsed 1.3.6.1.4.1.14179.2.6.2.59
The Preamble on this detecting AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER none(0), short(1), long(2)  

bsnTrustedApPreambleRequired 1.3.6.1.4.1.14179.2.6.2.60
The Preamble on this detecting AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER none(0), short(1), long(2)  

bsnSignatureAttackPreced 1.3.6.1.4.1.14179.2.6.2.61
The preced in the standard/custom signature list.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER 0..65535  

bsnSignatureAttackFrequency 1.3.6.1.4.1.14179.2.6.2.62
The preced in the standard/custom signature list.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER 0..65535  

bsnSignatureAttackChannel 1.3.6.1.4.1.14179.2.6.2.63
The preced in the standard/custom signature list.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER 0..65535  

bsnSignatureAttackerMacAddress 1.3.6.1.4.1.14179.2.6.2.64
The MAC address of the Attacker's mac-interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

bsnApRegulatoryDomain 1.3.6.1.4.1.14179.2.6.2.68
The regulatory domain configured on an AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER a(0), e(1), i(6), j(9), c(16), n(21), k(32), p(33), s(34), t(35), r(48), notavailable(65535)  

bsnRadiosExceedLicenseCount 1.3.6.1.4.1.14179.2.6.3.42
Whenever the currently associated Radios exceed the License Count This trap will be sent to annoy the Customer
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnSensedTemperatureTooHigh 1.3.6.1.4.1.14179.2.6.3.43
Temperature sensor temp too High - temp is too high on the unit. Immediate action should be taken
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnSensedTemperatureTooLow 1.3.6.1.4.1.14179.2.6.3.44
Temperature sensor temp too Low - temp is too high on the unit. Immediate action should be taken
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnTemperatureSensorFailure 1.3.6.1.4.1.14179.2.6.3.45
Temperature sensor hw failure - temp sensor has failed. Temperature is unknown
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnTemperatureSensorClear 1.3.6.1.4.1.14179.2.6.3.46
Temperature sensor clear -- temp sensor alarm condition is over. sensor is operating within proper temp range
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnPOEControllerFailure 1.3.6.1.4.1.14179.2.6.3.47
POE Controller has failed. Its a very critical trap. User intervention is required.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnMaxRogueCountExceeded 1.3.6.1.4.1.14179.2.6.3.48
The number of rogues has exceeded the maximum Rogues allowed
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnMaxRogueCountClear 1.3.6.1.4.1.14179.2.6.3.49
The number of rogues is within the maximum Rogues allowed
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnApMaxRogueCountExceeded 1.3.6.1.4.1.14179.2.6.3.50
The number of rogues has exceeded the maximum Rogues allowed on the AP
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnApMaxRogueCountClear 1.3.6.1.4.1.14179.2.6.3.51
The number of rogues is within the maximum Rogues allowed on the AP
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnApBigNavDosAttack 1.3.6.1.4.1.14179.2.6.3.55
The AP sent a string of messages with large NAV field. This is most likely a malicious denial of service attack.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnTooManyUnsuccessLoginAttempts 1.3.6.1.4.1.14179.2.6.3.56
The Management User made too many unsuccessful login attempts.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnWepKeyDecryptError 1.3.6.1.4.1.14179.2.6.3.57
Issued when a decrypt error occurrs. The WEP Key configured at the station may be wrong.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnWpaMicErrorCounterActivated 1.3.6.1.4.1.14179.2.6.3.58
Issued when a WPA MIC error occurs and a counter measure is activated at the AP.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnAdhocRogueAutoContained 1.3.6.1.4.1.14179.2.6.3.65
Issued when an Adhoc Rogue is auto contained. If the clear variable has value true, then the trap clears the earlier alert.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnRogueApAutoContained 1.3.6.1.4.1.14179.2.6.3.66
Issued when a Rogue AP is auto contained for advertising our SSID. If the clear variable has value true, then the trap clears the earlier alert.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnTrustedApHasInvalidEncryption 1.3.6.1.4.1.14179.2.6.3.67
Issued when a Trusted Rogue AP is auto contained for using invalid encryption. The second param is for the encryption used and the third param is for encryption required. If the clear variable has value true, then the trap clears the earlier alert.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnTrustedApHasInvalidRadioPolicy 1.3.6.1.4.1.14179.2.6.3.68
Issued when a Trusted Rogue AP is auto contained for using invalid radio policy. The second param is for the radio policy used and the third param is for radio policy required. If the clear variable has value true, then the trap clears the earlier alert.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnTrustedApHasInvalidSsid 1.3.6.1.4.1.14179.2.6.3.63
Issued when a Trusted Rogue AP is auto contained for advertising invalid SSID. If the clear variable has value true, then the trap clears the earlier alert.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnTrustedApIsMissing 1.3.6.1.4.1.14179.2.6.3.64
Issued when a Trusted Rogue AP is missing or has failed. If the clear variable has value true, then the trap clears the earlier alert.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnImpersonatingSourceMacAddr 1.3.6.1.4.1.14179.2.6.2.74
This is the source mac address which is impersonating the AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

bsnSyslog 1.3.6.1.4.1.14179.2.7.1
OBJECT IDENTIFIER    

bsnSyslogEnable 1.3.6.1.4.1.14179.2.7.1.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnSyslogRemoteAddress 1.3.6.1.4.1.14179.2.7.1.2
This would be the IP Address or host name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

bsnPing 1.3.6.1.4.1.14179.2.7.2
OBJECT IDENTIFIER    

bsnPingTestTable 1.3.6.1.4.1.14179.2.7.2.1
PingTest Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnPingTestEntry

bsnPingTestEntry 1.3.6.1.4.1.14179.2.7.2.1.1
An Entry (conceptual row) in the bsnPingTest Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnPingTestEntry  

bsnPingTestId 1.3.6.1.4.1.14179.2.7.2.1.1.1
Test ID
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..24  

bsnPingTestIPAddress 1.3.6.1.4.1.14179.2.7.2.1.1.2
Ip Address to ping
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnPingTestSendCount 1.3.6.1.4.1.14179.2.7.2.1.1.3
Number of bytes sent
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..20  

bsnPingTestReceivedCount 1.3.6.1.4.1.14179.2.7.2.1.1.4
Number of bytes received.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..20  

bsnPingTestStatus 1.3.6.1.4.1.14179.2.7.2.1.1.5
Status of the ping test
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inprogress(1), complete(2)  

bsnPingTestMaxTimeInterval 1.3.6.1.4.1.14179.2.7.2.1.1.6
Maximum time interval in msec.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnPingTestMinTimeInterval 1.3.6.1.4.1.14179.2.7.2.1.1.7
Minimum time interval in msec.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnPingTestAvgTimeInterval 1.3.6.1.4.1.14179.2.7.2.1.1.8
Average time interval in msec.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bsnPingTestRowStatus 1.3.6.1.4.1.14179.2.7.2.1.1.25
Row Status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnLinkTest 1.3.6.1.4.1.14179.2.7.3
OBJECT IDENTIFIER    

bsnLinkTestTable 1.3.6.1.4.1.14179.2.7.3.1
LinkTest Table
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnLinkTestEntry

bsnLinkTestEntry 1.3.6.1.4.1.14179.2.7.3.1.1
An Entry (conceptual row) in the bsnLinkTest Table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  BsnLinkTestEntry  

bsnLinkTestId 1.3.6.1.4.1.14179.2.7.3.1.1.1
Link Test ID
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32 0..24  

bsnLinkTestMacAddress 1.3.6.1.4.1.14179.2.7.3.1.1.2
MAC Address of link to test
Status: deprecated Access: read-create
OBJECT-TYPE    
  MacAddress  

bsnLinkTestSendPktCount 1.3.6.1.4.1.14179.2.7.3.1.1.3
Number of packets sent.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32 1..20  

bsnLinkTestSendPktLength 1.3.6.1.4.1.14179.2.7.3.1.1.4
Length of sent packet
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32 1..2000  

bsnLinkTestReceivedPktCount 1.3.6.1.4.1.14179.2.7.3.1.1.5
Number of received packets.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

bsnLinkTestClientRSSI 1.3.6.1.4.1.14179.2.7.3.1.1.6
Client RSSI value of link.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

bsnLinkTestLocalSNR 1.3.6.1.4.1.14179.2.7.3.1.1.7
Local SNR of the link
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

bsnLinkTestLocalRSSI 1.3.6.1.4.1.14179.2.7.3.1.1.8
Local RSSI of the link.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

bsnLinkTestStatus 1.3.6.1.4.1.14179.2.7.3.1.1.9
Status of the link test.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER inprogress(1), complete(2)  

bsnLinkTestRowStatus 1.3.6.1.4.1.14179.2.7.3.1.1.30
Row Status
Status: deprecated Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnMobilityConfig 1.3.6.1.4.1.14179.2.8.1
OBJECT IDENTIFIER    

bsnMobilityStats 1.3.6.1.4.1.14179.2.8.2
OBJECT IDENTIFIER    

bsnMobilityProtocolPortNum 1.3.6.1.4.1.14179.2.8.1.1
Port Number on which mobility Protocol runs
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bsnMobilityDynamicDiscovery 1.3.6.1.4.1.14179.2.8.1.3
Statically Configured is always enabled if members are defined. To further enable rrm discovery, learned discovery, broadcast discovery, enable/disable this attribute.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnMobilityStatsReset 1.3.6.1.4.1.14179.2.8.1.4
Reset mobility statistics by setting this atribute to resetNow. If you try to read this attribute value will always be 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), resetNow(1)  

bsnMobilityGroupMembersTable 1.3.6.1.4.1.14179.2.8.1.10
MWAR List (statically configured members of the mobility group)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobilityGroupMembersEntry

bsnMobilityGroupMembersEntry 1.3.6.1.4.1.14179.2.8.1.10.1
An Entry (conceptual row) in the bsnMobilityGroupMembers Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMobilityGroupMembersEntry  

bsnMobilityGroupMemberMacAddress 1.3.6.1.4.1.14179.2.8.1.10.1.1
Member switch MAC Address
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

bsnMobilityGroupMemberIPAddress 1.3.6.1.4.1.14179.2.8.1.10.1.2
Member switch IP Address
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnMobilityGroupMemberGroupName 1.3.6.1.4.1.14179.2.8.1.10.1.3
Member's group name. If left empty while adding a new group member, this assumes the default mobility group name of the switch.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

bsnMobilityGroupMemberRowStatus 1.3.6.1.4.1.14179.2.8.1.10.1.22
Row Status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnMobilityAnchorsTable 1.3.6.1.4.1.14179.2.8.1.11
Statically configured mobility anchors
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobilityAnchorsEntry

bsnMobilityAnchorsEntry 1.3.6.1.4.1.14179.2.8.1.11.1
An Entry (conceptual row) in the bsnMobilityAnchorsTable Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMobilityAnchorsEntry  

bsnMobilityAnchorWlanSsid 1.3.6.1.4.1.14179.2.8.1.11.1.1
Local wlan-ssid to connect to Guest/Anchor switch
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..32)  

bsnMobilityAnchorSwitchIPAddress 1.3.6.1.4.1.14179.2.8.1.11.1.2
Guest/Anchor switch IP Address
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

bsnMobilityAnchorRowStatus 1.3.6.1.4.1.14179.2.8.1.11.1.20
Row Status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnTotalHandoffRequests 1.3.6.1.4.1.14179.2.8.2.1
Total handoff requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffs 1.3.6.1.4.1.14179.2.8.2.2
Total handoffs
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnCurrentExportedClients 1.3.6.1.4.1.14179.2.8.2.3
Current exported client count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalExportedClients 1.3.6.1.4.1.14179.2.8.2.4
Total exported client count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnCurrentImportedClients 1.3.6.1.4.1.14179.2.8.2.5
Current Imported client count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalImportedClients 1.3.6.1.4.1.14179.2.8.2.6
Total Imported client count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffErrors 1.3.6.1.4.1.14179.2.8.2.7
Total handoff errors
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalCommunicationErrors 1.3.6.1.4.1.14179.2.8.2.8
Total communication errors
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalReceiveErrors 1.3.6.1.4.1.14179.2.8.2.10
Total receive errors
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalTransmitErrors 1.3.6.1.4.1.14179.2.8.2.11
Total Transmit errors
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalResponsesRetransmitted 1.3.6.1.4.1.14179.2.8.2.12
Total Responses Retransmitted
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffEndRequestsReceived 1.3.6.1.4.1.14179.2.8.2.13
Total Handoff End Requests Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalStateTransitionsDisallowed 1.3.6.1.4.1.14179.2.8.2.14
Total State Transitions Disallowed
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalResourceErrors 1.3.6.1.4.1.14179.2.8.2.15
Total Resource Errors
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRequestsSent 1.3.6.1.4.1.14179.2.8.2.16
Total Handoff Requests Sent
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRepliesReceived 1.3.6.1.4.1.14179.2.8.2.17
Total Handoff Replies Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffAsLocalReceived 1.3.6.1.4.1.14179.2.8.2.18
Total Handoffs As Local Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffAsForeignReceived 1.3.6.1.4.1.14179.2.8.2.19
Total Handoffs As Foreign Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffDeniesReceived 1.3.6.1.4.1.14179.2.8.2.20
Total Handoff Denies Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorRequestsSent 1.3.6.1.4.1.14179.2.8.2.21
Total Anchor Requests Sent
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorDenyReceived 1.3.6.1.4.1.14179.2.8.2.22
Total Anchor Deny Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorGrantReceived 1.3.6.1.4.1.14179.2.8.2.23
Total Anchor Grant Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorTransferReceived 1.3.6.1.4.1.14179.2.8.2.24
Total Anchor Transfer Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRequestsIgnored 1.3.6.1.4.1.14179.2.8.2.25
Total Handoff Requests Ignored
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalPingPongHandoffRequestsDropped 1.3.6.1.4.1.14179.2.8.2.26
Total Ping Pong Handoff Requests Dropped
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRequestsDropped 1.3.6.1.4.1.14179.2.8.2.27
Total Handoff Requests Dropped
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRequestsDenied 1.3.6.1.4.1.14179.2.8.2.28
Total Handoff Requests Denied
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalClientHandoffAsLocal 1.3.6.1.4.1.14179.2.8.2.29
Total Client Handoffs As Local
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalClientHandoffAsForeign 1.3.6.1.4.1.14179.2.8.2.30
Total Client Handoffs As Foreign
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorRequestsReceived 1.3.6.1.4.1.14179.2.8.2.31
Total Anchor Requests Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorRequestsDenied 1.3.6.1.4.1.14179.2.8.2.32
Total Anchor Requests Denied
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorRequestsGranted 1.3.6.1.4.1.14179.2.8.2.33
Total Anchor Requests Granted
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorTransferred 1.3.6.1.4.1.14179.2.8.2.34
Total Anchor Transferred
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRequestsReceived 1.3.6.1.4.1.14179.2.8.2.35
Total Handoff Requests Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMobilityGroupDirectoryTable 1.3.6.1.4.1.14179.2.8.2.9
MWAR List (statically configured members of the mobility group)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobilityGroupDirectoryEntry

bsnMobilityGroupDirectoryEntry 1.3.6.1.4.1.14179.2.8.2.9.1
An Entry (conceptual row) in the bsnMobilityGroupDirectory Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnMobilityGroupDirectoryEntry  

bsnGroupDirectoryMemberIPAddress 1.3.6.1.4.1.14179.2.8.2.9.1.1
Mwar Ip Address
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bsnGroupDirectoryMemberMacAddress 1.3.6.1.4.1.14179.2.8.2.9.1.2
Mwar Mac Address
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

bsnGroupDirectoryDicoveryType 1.3.6.1.4.1.14179.2.8.2.9.1.3
Discovery type of the Group Directory.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER static(1), rrm(2), broadcast(3), learned(4)  

bsnMemberCurrentAnchoredClients 1.3.6.1.4.1.14179.2.8.2.9.1.4
Current anchored client count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMemberTotalAnchoredClients 1.3.6.1.4.1.14179.2.8.2.9.1.5
Total anchored client count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMemberCurrentExportedClients 1.3.6.1.4.1.14179.2.8.2.9.1.6
Current exported client count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMemberTotalExportedClients 1.3.6.1.4.1.14179.2.8.2.9.1.7
Total exported client count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMemberCurrentImportedClients 1.3.6.1.4.1.14179.2.8.2.9.1.8
Current Imported client count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMemberTotalImportedClients 1.3.6.1.4.1.14179.2.8.2.9.1.9
Total Imported client count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMemberTotalHandoffErrors 1.3.6.1.4.1.14179.2.8.2.9.1.10
Total handoff errors
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnMemberTotalCommunicationErrors 1.3.6.1.4.1.14179.2.8.2.9.1.30
Total Communication errors
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bsnAPGroupsVlanConfig 1.3.6.1.4.1.14179.2.10
OBJECT IDENTIFIER    

bsnAPGroupsVlanFeature 1.3.6.1.4.1.14179.2.10.1
When enabled, Site Specific WLAN feature is enforced.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPGroupsVlanTable 1.3.6.1.4.1.14179.2.10.2
Wireless Sites Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPGroupsVlanEntry

bsnAPGroupsVlanEntry 1.3.6.1.4.1.14179.2.10.2.1
An entry in bsnAPGroupsVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BsnAPGroupsVlanEntry  

bsnAPGroupsVlanName 1.3.6.1.4.1.14179.2.10.2.1.1
The string is an unique identifier/name assigned to a site.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

bsnAPGroupsVlanDescription 1.3.6.1.4.1.14179.2.10.2.1.2
Description about the site.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bsnAPGroupsVlanRowStatus 1.3.6.1.4.1.14179.2.10.2.1.20
Row Status for creation/deletion of entries in bsnAPGroupsVlanTable
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnAPGroupsVlanMappingTable 1.3.6.1.4.1.14179.2.10.3
A table for the WLAN-interace-mappings allowed for each configured site. Each site can have a set of WLANs associated with it.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPGroupsVlanMappingEntry

bsnAPGroupsVlanMappingEntry 1.3.6.1.4.1.14179.2.10.3.1
An entry in bsnAPGroupsVlanMappingTable.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  BsnAPGroupsVlanMappingEntry  

bsnAPGroupsVlanMappingSsid 1.3.6.1.4.1.14179.2.10.3.1.1
When an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP. Here 'bsnAPGroupsVlanMappingSsid' is the wlan to be used when a client connects on this AP.
Status: deprecated Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..32)  

bsnAPGroupsVlanMappingInterfaceName 1.3.6.1.4.1.14179.2.10.3.1.2
When an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP. Here 'bsnAPGroupsVlanMappingInterfaceName' is the interface to be used when a client connects to the 'bsnAPGroupsVlanMappingSsid' WLAN on this AP.
Status: deprecated Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

bsnAPGroupsVlanMappingRowStatus 1.3.6.1.4.1.14179.2.10.3.1.20
Row Status for creation/deletion of WLAN-interface-mappings asscoiated with sites.
Status: deprecated Access: read-create
OBJECT-TYPE    
  RowStatus  

bsnAPIPAddressFallback 1.3.6.1.4.1.14179.2.6.3.77
This trap is sent out when an AP, with the configured static ip-address, fails to establish connection with outside world and starts using DHCP as a fallback option.
Status: current Access: read-create
NOTIFICATION-TYPE    

bsnAPFunctionalityDisabled 1.3.6.1.4.1.14179.2.6.3.78
This trap is sent out when AP functionality on the switch is disabled because the License key has expired or has been deleted or doesn't match the switch image.
Status: current Access: read-create
NOTIFICATION-TYPE    

bsnLicenseKeyTrapVariable 1.3.6.1.4.1.14179.2.6.2.65
This is the license key that has been found to be deleted, expired or is mismatched causing AP functionality to be disabled on the switch.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

bsnApFunctionalityDisableReasonCode 1.3.6.1.4.1.14179.2.6.2.66
This is the reason why the AP functionality was disabled on the switch. It could be either expiry or deletion or mismatch found of the license key.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER unknown(0), licenseKeyExpired(1), licenseKeyDeleted(2), licenseKeyFeatureMismatch(3)  

bsnLicenseKeyFeatureSetTrapVariable 1.3.6.1.4.1.14179.2.6.2.67
This is the switch feature set whose license key has expired or is deleted or is mismatched. To enable the AP functionality again, the license key for this feature set should be re-configured.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER wps(1), all(2)  

bsnRxMulticastQueueFull 1.3.6.1.4.1.14179.2.6.3.80
This trap indicates that the CPU's Receive Multicast Queue is Full.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnAPAuthorizationFailureCause 1.3.6.1.4.1.14179.2.6.2.69
This denotes the reason for AP authorization failure. [entrydoesnotexist]: The AP has not been added to Controller's AP Authorization List. [keymismatch]: The key entry in Controller's AP Authorization list does not match the SHA1 key received from the AP. [invalidCert]: Could not verify the self signed Certificate. [entryIsMIC]: AP has Self Signed Certificate where as in Controller AP Authorization list has Manufactured Installed Certificate [aaaEntryDoesNotExist]: RADIUS authorization for the AP failed. [unknown]: Default.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER unknown(0), keymismatch(1), entrydoesnotexist(2), invalidCertifcate(3), entryIsMIC(4), aaaEntryDoesNotExist(5)  

bsnAPIfUpDownCause 1.3.6.1.4.1.14179.2.6.2.70
This denotes the reason for AP If up or down normal - radio Failure - radio failed radioLowPower - AP is not able draw enough power. maxRetransmission - max retransmission of AP Reached. echoTimeout - heartbeat timeout. configAP - admin enable/disable AP configRadio - admin enable/disable config radio configNetwork - admin enable/disable network adminConfigured - admin configuration missedRekey - Missed Rekey detectingInLinePower - Detecting in-line power newDiscovery - New Discovery
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER unknown(0), radioFailure(1), radioLowPower(2), maxRetransmission(3), echoTimeout(4), configAP(5), configRadio(6), configNetwork(7), adminConfigured(8), missedRekey(9), detectingInLinePower(10), newDiscovery(11)  

bsnAPInvalidRadioType 1.3.6.1.4.1.14179.2.6.2.71
Radio types which are not supported by controller.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER unsupportedRadio(0)  

locationNotifyContent 1.3.6.1.4.1.14179.2.6.2.72
This is the content of the notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

bsnSignatureMacInfo 1.3.6.1.4.1.14179.2.6.2.73
This object defines the pattern followed by the LWAPP APs to perform signature analysis with this signature and report the results to the Controller.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  BsnTxtSignatureMacInfo  

bsnRadarChannelDetected 1.3.6.1.4.1.14179.2.6.3.81
This trap is sent when radar signals are detected on the current channel
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnRadarChannelCleared 1.3.6.1.4.1.14179.2.6.3.82
This trap will be generated, if a radar trap has been generated earlier, after the expiry of Non-Occupancy Period.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnAPAuthorizationFailure 1.3.6.1.4.1.14179.2.6.3.83
This trap is sent out in case of authorization failure while attempting to associate the AP to the controller. bsnAPDot3MacAddress represents the mac-address of that AP. bsnAPName is name of AP
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

radioCoreDumpTrap 1.3.6.1.4.1.14179.2.6.3.84
When radio module in AP dumps core, it informs controller and controller generates this trap. The core file can be retrieved on demand.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

invalidRadioTrap 1.3.6.1.4.1.14179.2.6.3.85
This trap will be generated when an AP has joined is using unsupported radio or a radio slot not currently not being used.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

countryChangeTrap 1.3.6.1.4.1.14179.2.6.3.86
This trap will be generated when an operator changes the country of operation. New country code will be sent in trap.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-TYPE    

unsupportedAPTrap 1.3.6.1.4.1.14179.2.6.3.87
This trap will be generated when unsupported AP try to join 40xx/410x or 3500 with 64MB flash.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

heartbeatLossTrap 1.3.6.1.4.1.14179.2.6.3.88
This trap will be generated when controller loses connection with the Supervisor Switch in which it is physically embedded and doesn't hear the heartbeat keepalives from the Supervisor.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

locationNotifyTrap 1.3.6.1.4.1.14179.2.6.3.89
This trap will be generated by the location server for notifications of location events.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

bsnWrasCompliance 1.3.6.1.4.1.14179.2.51.1
The compliance statement for the SNMP entities that implement the bsnWireless module.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

bsnWrasComplianceRev1 1.3.6.1.4.1.14179.2.51.2
The compliance statement for the SNMP entities that implement the bsnWireless module.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

bsnEssGroup 1.3.6.1.4.1.14179.2.50.1
This collection of objects provides information about Airespace Wireless LAN Configuration Attributes These objects are defined under bsnEss object.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

bsnApGroup 1.3.6.1.4.1.14179.2.50.2
This collection of objects provide the information about Airespace APs that are associated with the Switch. These objects are defined under bsnAP object.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

bsnGlobalDot11Group 1.3.6.1.4.1.14179.2.50.3
This collection of objects provide the information about Airespace 802.11 standard attributes applied globally. These objects are defined under bsnGlobalDot11 object.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

bsnRrmGroup 1.3.6.1.4.1.14179.2.50.4
This collection of objects provide the information about Airespace Radio Resource Management Configuration Parameters. These objects are defined under bsnRrm object.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

bsnAAAGroup 1.3.6.1.4.1.14179.2.50.5
This collection of objects provide the information about Airespace Authentication, Authorization, and Accounting Attributes. These objects are defined under bsnAAA object.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

bsnTrapsGroup 1.3.6.1.4.1.14179.2.50.6
This collection of objects provide the information about Airespace Trap Configuration and Trap definition. These objects are defined under bsnTrap.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

bsnUtilityGroup 1.3.6.1.4.1.14179.2.50.7
This collection of objects provide the information about Airespace General Utilities such as ping, syslog. These objects are defined under bsnUtility.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

bsnMobilityGroup 1.3.6.1.4.1.14179.2.50.8
This collection of objects provide the information about Airespace Mobility Group Parameters and ststistics. These are objects defined under bsnMobility.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

bsnIpsecGroup 1.3.6.1.4.1.14179.2.50.9
This collection of objects provide the information about Airespace Global IpSec Group. These objects are defined under bsnIpsec.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

bsnWrasDepGroup 1.3.6.1.4.1.14179.2.50.10
This collection of objects are derprecated in bsnWireless module.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

bsnWrasObsGroup 1.3.6.1.4.1.14179.2.50.11
This collection of objects are obsoleted in bsnWireless module.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

bsnWrasTrap 1.3.6.1.4.1.14179.2.50.12
This collection of objects provides all notification that Switch need to generate to the Management System.
Status: obsolete Access: accessible-for-notify
NOTIFICATION-GROUP    

bsnEssGroupRev1 1.3.6.1.4.1.14179.2.50.13
This collection of objects provides information about Airespace Wireless LAN Configuration Attributes These objects are defined under bsnEss object.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

bsnGlobalDot11GroupRev1 1.3.6.1.4.1.14179.2.50.14
This collection of objects provide the information about Airespace 802.11 standard attributes applied globally. These objects are defined under bsnGlobalDot11 object.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

bsnAAAGroupRev1 1.3.6.1.4.1.14179.2.50.15
This collection of objects provide the information about Airespace Authentication, Authorization, and Accounting Attributes. These objects are defined under bsnAAA object.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

bsnTrapsGroupRev1 1.3.6.1.4.1.14179.2.50.16
This collection of objects provide the information about Airespace Trap Configuration and Trap definition. These objects are defined under bsnTrap.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

bsnWrasTrapRev1 1.3.6.1.4.1.14179.2.50.17
This collection of objects provides all notification that Switch need to generate to the Management System.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

bsnApGroupRev1 1.3.6.1.4.1.14179.2.50.18
This collection of objects provide the information about Airespace APs that are associated with the Switch. These objects are defined under bsnAP object.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

bsnUtilityGroupRev1 1.3.6.1.4.1.14179.2.50.19
This collection of objects provide the information about Airespace General Utilities such as ping, syslog. These objects are defined under bsnUtility.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

bsnWrasObsGroupRev1 1.3.6.1.4.1.14179.2.50.20
This collection of objects are obsoleted in bsnWireless module.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

bsnWrasObsTrap 1.3.6.1.4.1.14179.2.50.21
This collection of objects provides all notification that Switch need to generate to the Management System.
Status: obsolete Access: accessible-for-notify
NOTIFICATION-GROUP