AIX1-MIB

File: AIX1-MIB.mib (81226 bytes)

Imported modules

Imported symbols

DisplayString	MODULE-IDENTITY	OBJECT-TYPE
Counter32	Integer32	enterprises

Defined Types

IfIndexType
INTEGER	1..2147483647

ApplAdminEntry
SEQUENCE
	aix1ApplAdminIndex	IfIndexType
	aix1ApplAdminLinkStart	INTEGER
	aix1ApplAdminLinkMode	INTEGER
	aix1ApplAdminResetErrs	INTEGER
	aix1ApplAdminXONXOFFProto	INTEGER
	aix1ApplAdminNMAProto	INTEGER
	aix1ApplAdminOPSINEProto	INTEGER
	aix1ApplAdminTL1Proto	INTEGER
	aix1ApplAdminLinkDescription	DisplayString
	aix1ApplAdminLinkConnectionMode	INTEGER

ApplOperEntry
SEQUENCE
	aix1ApplOperIndex	IfIndexType
	aix1ApplOperLinkMode	INTEGER
	aix1ApplOperXONXOFFProto	INTEGER
	aix1ApplOperNMAProto	INTEGER
	aix1ApplOperOPSINEProto	INTEGER
	aix1ApplOperTL1Proto	INTEGER
	aix1ApplOperLinkDescription	DisplayString
	aix1ApplOperLinkConnectionMode	INTEGER

PktAdminEntry
SEQUENCE
	aix1PktAdminIndex	IfIndexType
	aix1PktAdminConformanceMode	INTEGER
	aix1PktAdminDBit	INTEGER
	aix1PktAdminQBitMBit	INTEGER
	aix1PktAdminUseRejectPkts	INTEGER
	aix1PktAdminSendInitialRestart	INTEGER
	aix1PktAdminStdsBody	INTEGER
	aix1PktAdminFacilChecking	INTEGER
	aix1PktAdminUndefinedFacils	INTEGER
	aix1PktAdminDefMaxPktSize	INTEGER
	aix1PktAdminDefWindowSize	INTEGER
	aix1PktAdminNegMaxPktSize	INTEGER
	aix1PktAdminNegWindowSize	INTEGER
	aix1PktAdminPacketizingTimer	INTEGER
	aix1PktAdminPVCOffset	INTEGER
	aix1PktAdminSVCOffset	INTEGER

PktOperEntry
SEQUENCE
	aix1PktOperIndex	IfIndexType
	aix1PktOperConformanceMode	INTEGER
	aix1PktOperDBit	INTEGER
	aix1PktOperQBitMBit	INTEGER
	aix1PktOperUseRejectPkts	INTEGER
	aix1PktOperSendInitialRestart	INTEGER
	aix1PktOperStdsBody	INTEGER
	aix1PktOperFacilChecking	INTEGER
	aix1PktOperUndefinedFacils	INTEGER
	aix1PktOperDefMaxPktSize	INTEGER
	aix1PktOperDefWindowSize	INTEGER
	aix1PktOperNegMaxPktSize	INTEGER
	aix1PktOperNegWindowSize	INTEGER
	aix1PktOperPacketizingTimer	INTEGER
	aix1PktOperPVCOffset	INTEGER
	aix1PktOperSVCOffset	INTEGER

PktStatEntry
SEQUENCE
	aix1PktStatIndex	IfIndexType
	aix1PktStatInCharsPerSec80s	Counter32
	aix1PktStatOutCharsPerSec80s	Counter32

FrmAdminEntry
SEQUENCE
	aix1FrmAdminIndex	IfIndexType
	aix1FrmAdminIdleRRs	INTEGER
	aix1FrmAdminRandomizeT1	INTEGER

FrmOperEntry
SEQUENCE
	aix1FrmOperIndex	IfIndexType
	aix1FrmOperIdleRRs	INTEGER
	aix1FrmOperRandomizeT1	INTEGER

PhysAdminEntry
SEQUENCE
	aix1PhysAdminIndex	IfIndexType
	aix1PhysAdminInterFrameDelayStatus	INTEGER
	aix1PhysAdminInterFrameDelayInterval	INTEGER
	aix1PhysAdminT1LineBuildOut	INTEGER

PhysOperEntry
SEQUENCE
	aix1PhysOperIndex	IfIndexType
	aix1PhysOperInterFrameDelayStatus	INTEGER
	aix1PhysOperInterFrameDelayInterval	INTEGER
	aix1PhysOperT1LineBuildOut	INTEGER

PhysStatEntry
SEQUENCE
	aix1PhysStatIndex	IfIndexType
	aix1PhysStatTxAborts	Counter32

CircuitEntry
SEQUENCE
	aix1CircuitLinkId	IfIndexType
	aix1CircuitChannelNumber	INTEGER
	aix1CircuitState	INTEGER
	aix1CircuitConType	INTEGER
	aix1CircuitBCNumber	INTEGER
	aix1CircuitUserData	DisplayString
	aix1CircuitRemoteBasePort	INTEGER
	aix1CircuitRemoteVCNumber	INTEGER
	aix1CircuitPktsSent	Counter32
	aix1CircuitPktsRcvd	Counter32
	aix1CircuitOperPVCType	INTEGER
	aix1CircuitOperPVCTimer	INTEGER

VCEntry
SEQUENCE
	aix1VCVCNumber	INTEGER	0..287
	aix1VCState	INTEGER
	aix1VCConType	INTEGER
	aix1VCBCNumber	INTEGER
	aix1VCUserData	DisplayString
	aix1VCRemoteBasePort	INTEGER
	aix1VCRemoteVCNumber	INTEGER
	aix1VCPktsSent	Counter32
	aix1VCPktsRcvd	Counter32
	aix1VCOperPVCType	INTEGER
	aix1VCOperPVCTimer	INTEGER

AdminPVCEntry
SEQUENCE
	aix1AdminPVCLinkId	IfIndexType
	aix1AdminPVCChannelNumber	INTEGER
	aix1AdminPVCType	INTEGER
	aix1AdminPVCTimer	INTEGER

Defined Values

aii		1.3.6.1.4.1.539
OBJECT IDENTIFIER

aiSystemOID		1.3.6.1.4.1.539.2
OBJECT IDENTIFIER

aiX1		1.3.6.1.4.1.539.12
OBJECT IDENTIFIER

aiX1System		1.3.6.1.4.1.539.12.1
OBJECT IDENTIFIER

aiX1Appl		1.3.6.1.4.1.539.12.2
OBJECT IDENTIFIER

aiX1Pkt		1.3.6.1.4.1.539.12.3
OBJECT IDENTIFIER

aiX1Frm		1.3.6.1.4.1.539.12.4
OBJECT IDENTIFIER

aiX1Phys		1.3.6.1.4.1.539.12.5
OBJECT IDENTIFIER

aiX1VC		1.3.6.1.4.1.539.12.6
OBJECT IDENTIFIER

ai192		1.3.6.1.4.1.539.2.192
OBJECT IDENTIFIER

ai192Ver7		1.3.6.1.4.1.539.2.192.7
OBJECT IDENTIFIER

ai192Ver70		1.3.6.1.4.1.539.2.192.7.0
OBJECT IDENTIFIER

ai192Ver708		1.3.6.1.4.1.539.2.192.7.0.8
OBJECT IDENTIFIER

ai192Ver709		1.3.6.1.4.1.539.2.192.7.0.9
OBJECT IDENTIFIER

ai192Ver71		1.3.6.1.4.1.539.2.192.7.1
OBJECT IDENTIFIER

ai192Ver710		1.3.6.1.4.1.539.2.192.7.1.0
OBJECT IDENTIFIER

ai192Ver711		1.3.6.1.4.1.539.2.192.7.1.1
OBJECT IDENTIFIER

ai192Ver72		1.3.6.1.4.1.539.2.192.7.2
OBJECT IDENTIFIER

ai192Ver720		1.3.6.1.4.1.539.2.192.7.2.0
OBJECT IDENTIFIER

ai192Ver721		1.3.6.1.4.1.539.2.192.7.2.1
OBJECT IDENTIFIER

ai192Ver77		1.3.6.1.4.1.539.2.192.7.7
OBJECT IDENTIFIER

ai196		1.3.6.1.4.1.539.2.196
OBJECT IDENTIFIER

ai196Ver7		1.3.6.1.4.1.539.2.196.7
OBJECT IDENTIFIER

ai196Ver70		1.3.6.1.4.1.539.2.196.7.0
OBJECT IDENTIFIER

ai196Ver708		1.3.6.1.4.1.539.2.196.7.0.8
OBJECT IDENTIFIER

ai196Ver709		1.3.6.1.4.1.539.2.196.7.0.9
OBJECT IDENTIFIER

ai196Ver71		1.3.6.1.4.1.539.2.196.7.1
OBJECT IDENTIFIER

ai196Ver710		1.3.6.1.4.1.539.2.196.7.1.0
OBJECT IDENTIFIER

ai196Ver711		1.3.6.1.4.1.539.2.196.7.1.1
OBJECT IDENTIFIER

ai196Ver72		1.3.6.1.4.1.539.2.196.7.2
OBJECT IDENTIFIER

ai196Ver720		1.3.6.1.4.1.539.2.196.7.2.0
OBJECT IDENTIFIER

ai196Ver721		1.3.6.1.4.1.539.2.196.7.2.1
OBJECT IDENTIFIER

ai196Ver77		1.3.6.1.4.1.539.2.196.7.7
OBJECT IDENTIFIER

aix1AdminGbufXoffThreshold		1.3.6.1.4.1.539.12.1.1
The configured XOFF global flow control threshold. If zero and if aix1AdminGbufRecovThreshold is zero, the global flow control mechanism is disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..ffff

aix1AdminGbufRecovThreshold		1.3.6.1.4.1.539.12.1.2
The configured recovery global flow control threshold. If zero and if aix1AdminGbufXoffThreshold is zero, the global flow control mechanism is disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..ffff

aix1AdminRollover		1.3.6.1.4.1.539.12.1.3
This object has been depricated and remains in the MIB for backward compatibility.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ready(1), roll(2)

aix1Bx25AdminCallDown		1.3.6.1.4.1.539.12.1.4
If set to off(2), an active BX.25 link will stay up after all calls are disconnected. If set to on(1), an active BX.25 link will drop and go into DMLOCK (see aix1Bx25AdminDMlock below) when all the link's backplane connections are terminated. This object is meaningful only when aix1ApplOperLinkMode is set to passive(2) on a given packet layer entity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

aix1Bx25AdminDMlock		1.3.6.1.4.1.539.12.1.5
The number of seconds to wait after a BX.25 passive link has gone inactive before allowing an outgoing call to attempt to bring up the link. Any outgoing call attempts will be rejected until the DMLOCK timer expires and the passive link returns to the standby mode. This object is meaningful only when aix1ApplOperLinkMode is set to passive(2) on a given packet layer entity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	25..ffffffff

aix1Bx25AdminLinkUp		1.3.6.1.4.1.539.12.1.6
The number of seconds to wait for a passive link to become active. This object is meaningful only when aix1ApplOperLinkMode is set to passive(2) on a given packet layer entity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	5..ffffffff

aix1StatErrX25InData		1.3.6.1.4.1.539.12.1.7
Number of data bytes from X.25 which were lost due to buffer failures.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrX25OutData		1.3.6.1.4.1.539.12.1.8
Number of data bytes from the FIFO which were discarded due to buffer failures.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrX25OutPkt		1.3.6.1.4.1.539.12.1.9
Number of messages from X.25 to GCOM which were lost due to some kind of resource failure in the GCOM library.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrX25OutChoked		1.3.6.1.4.1.539.12.1.10
Number of times a port has received a flow control stop message from GCOM(or perhaps from X.25), and thus entered the Choked state. This may not be indicative of a serious problem, but may also mean that data has been lost.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrPlogCount		1.3.6.1.4.1.539.12.1.11
Number of times an internal error routine has been called due to unexpected packets received from GCOM ( or X.25).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrGfctlXoffs		1.3.6.1.4.1.539.12.1.12
Number of times the global flow control mechanism attempted to back pressure data flow from the backplane.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrGfctlDiscards		1.3.6.1.4.1.539.12.1.13
Number of times the global flow control mechanism has detected a buffer level so low that it discarded data received from the backplane.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrUwteBadTrans		1.3.6.1.4.1.539.12.1.14
Number of unified window transactions with bad transaction codes received from CLC or a remote SLC. If this counter is non-zero, it indicated the presence of incompatible versions of firmware on the SLC and CLC, or a bug in either the SLC or CLC firmware.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrUwteBadFlds		1.3.6.1.4.1.539.12.1.15
Number of invalid fields received in unified window transactions. If this counter is non-zero, it indicates the presence of incompatible versions or a bug in either the SLC or CLC firmware.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrUwteMissingFlds		1.3.6.1.4.1.539.12.1.16
Number of required fields absent from received unified window transactions. If this counter is non-zero, it indicates the presence of incompatible versions or a bug in either the SLC or CLC firmware.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrLogOutLost		1.3.6.1.4.1.539.12.1.17
Number of outbound log messages discarded to avoid flooding the log. This arises because the SLC is attempting to generate log messages too frequently on a particular TDS or globally. When this occurs, the SLC will discard the log message and increment the counter. This is not a serious error, and typically occurs during periods of intense, repetitive logging activity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrVcMuxErrs		1.3.6.1.4.1.539.12.1.18
Number of serious multiplexing errors which have occurred. Such an error generally involves an impossible value in an internal header or receipt of a message on the wrong internal channel.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatErrEmptyPktsRcv		1.3.6.1.4.1.539.12.1.19
Number of empty data packets received from the network.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatInCharsPerSec80s		1.3.6.1.4.1.539.12.1.20
The average number of data characters (characters in the data field of X.25 data packets) received from the network per second over the last 80 seconds.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1StatOutCharsPerSec80s		1.3.6.1.4.1.539.12.1.21
The average number of data characters (characters in the data field of X.25 data packets) transmitted to the network per second over the last 80 seconds.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1ApplAdminTable		1.3.6.1.4.1.539.12.2.1
The table of administrative elements which apply to an individual X.25 link above the packet layer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ApplAdminEntry

aix1ApplAdminEntry		1.3.6.1.4.1.539.12.2.1.1
The addressing information for one of this X.25 link's administrative objects.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ApplAdminEntry

aix1ApplAdminIndex		1.3.6.1.4.1.539.12.2.1.1.1
The ifIndex value of the packet layer entity associated with these application level objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1ApplAdminLinkStart		1.3.6.1.4.1.539.12.2.1.1.2
Start or stop a link that's enabled by the standard MIB link status objects. If the link is not enabled by the standard MIB objects, a write to this object will have no effect. Stopping a link by writing to this object does not free significant resources, it just stops activity on the link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	started(1), stopped(2)

aix1ApplAdminLinkMode		1.3.6.1.4.1.539.12.2.1.1.3
Determines whether link behaves as a normal X.25 link or a BX.25-style passive link. This is the most recently configured value of this attribute, and may not yet have taken effect. The current operating value is available as aix1ApplOperLinkMode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), passive(2)

aix1ApplAdminResetErrs		1.3.6.1.4.1.539.12.2.1.1.4
Writing the value resetCounters(2) to this object resets the per-link level 1 error counters. No other writes are accepted. They are aix1PhysStatRxCRCErrors, aix1PhysStatRxAborts, aix1PhysStatRxOverruns, aix1PhysStatTxAborts, aix1PhysStatTxUnderruns.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), resetCounters(2)

aix1ApplAdminXONXOFFProto		1.3.6.1.4.1.539.12.2.1.1.5
Determines whether XON/XOFF protocol processing is in effect by default on all virtual circuits on the link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

aix1ApplAdminNMAProto		1.3.6.1.4.1.539.12.2.1.1.6
Determines whether NMA protocol processing is in effect by default on all virtual circuits on the link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

aix1ApplAdminOPSINEProto		1.3.6.1.4.1.539.12.2.1.1.7
Determines whether OPSINE protocol processing is in effect by default on all virtual circuits on the link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

aix1ApplAdminTL1Proto		1.3.6.1.4.1.539.12.2.1.1.8
Determines whether TL1 protocol processing is in effect by default on all virtual circuits on the link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

aix1ApplAdminLinkDescription		1.3.6.1.4.1.539.12.2.1.1.9
A descriptive string associated with this link. This provides a place for the agent to supply any descriptive information about the use or owner of the link. A zero length value indicates that the agent doesn't have any additional information.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..50)

aix1ApplAdminLinkConnectionMode		1.3.6.1.4.1.539.12.2.1.1.10
Connect or disconnect a link that's enabled by the standard MIB linmk status objects. If the link is not enabled by the standard MIB objects, a write to this object will have no effect. Disconnecting a link by writing to this object does not free any resources, it marks the link as not connected, so that the link will not cause a level 4 (LINKDOWN) alarm to be generated.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	connected(1), disconnected(2), disabled(4)

aix1ApplOperTable		1.3.6.1.4.1.539.12.2.2
The table of operational elements which apply to an individual X.25 link above the packet layer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ApplOperEntry

aix1ApplOperEntry		1.3.6.1.4.1.539.12.2.2.1
The addressing information for one of this X.25 link's operational objects.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ApplOperEntry

aix1ApplOperIndex		1.3.6.1.4.1.539.12.2.2.1.1
The ifIndex value of the packet level associated with these application level objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1ApplOperLinkMode		1.3.6.1.4.1.539.12.2.2.1.2
Determines whether link behaves as a normal X.25 link or a BX.25-style passive link. This is the mandatory operating value of this attribute. The most recently configured value is available as aix1ApplAdminLinkMode.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), passive(2)

aix1ApplOperXONXOFFProto		1.3.6.1.4.1.539.12.2.2.1.3
Determines whether XON/XOFF protocol processing is in effect by default on all virtual circuits on the link.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

aix1ApplOperNMAProto		1.3.6.1.4.1.539.12.2.2.1.4
Determines whether NMA protocol processing is in effect by default on all virtual circuits on the link.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

aix1ApplOperOPSINEProto		1.3.6.1.4.1.539.12.2.2.1.6
Determines whether OPSINE protocol processing is in effect by default on all virtual circuits on the link.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

aix1ApplOperTL1Proto		1.3.6.1.4.1.539.12.2.2.1.7
Determines whether TL1 protocol processing is in effect by default on all virtual circuits on the link.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

aix1ApplOperLinkDescription		1.3.6.1.4.1.539.12.2.2.1.8
A descriptive string associated with this link. This provides a place for the agent to supply any descriptive information about the use or owner of the link. A zero length value indicates that the agent doesn't have any additional information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..50)

aix1ApplOperLinkConnectionMode		1.3.6.1.4.1.539.12.2.2.1.9
Determines whether the link is currently disconnected, connected or has been reconnected after it was disconnected.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	connected(1), disconnected(2), reconnected(3), disabled(4), linkdown(5), linkup(6)

aix1PktAdminTable		1.3.6.1.4.1.539.12.3.1
The table of administrative elements which apply to an individual X.25 link at the packet layer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PktAdminEntry

aix1PktAdminEntry		1.3.6.1.4.1.539.12.3.1.1
The addressing information for one of this X.25 link's packet layer administrative objects.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	PktAdminEntry

aix1PktAdminIndex		1.3.6.1.4.1.539.12.3.1.1.1
The ifIndex value of the packet layer entity associated with these objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1PktAdminConformanceMode		1.3.6.1.4.1.539.12.3.1.1.2
The configured conformance testing mode to which X.25's behavior will adhere. This value may not have taken effect. The value with which the SLC is currently operating is the value of aix1OperConformanceMode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ccitt(1), ddn(2)

aix1PktAdminDBit		1.3.6.1.4.1.539.12.3.1.1.3
Determines whether the packet level will allow the D-bit in call setup packets.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbitNotAllowed(1), dbitAllowed(2)

aix1PktAdminQBitMBit		1.3.6.1.4.1.539.12.3.1.1.4
Determines whether the packet level will check for consistency in the use of Q and M bits, i. e. that the value of the Q-bit is the same in every packet of an M-bit sequence.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noQMCheck(1), qmCheck(2)

aix1PktAdminUseRejectPkts		1.3.6.1.4.1.539.12.3.1.1.5
Enables and disables the use of packet retransmission. If the packet level is acting as a DTE it will send a REJ packet in response to a data packet received out of sequence. If the packet level is acting as a DCE, it will accept a REJ packet and retransmit the requested data packet(s).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noPktRetrans(1), pktRetrans(2)

aix1PktAdminSendInitialRestart		1.3.6.1.4.1.539.12.3.1.1.6
Enables and disables sending of an initial restart request packet when the link comes up.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	initialRestart(1), noInitialRestart(2)

aix1PktAdminStdsBody		1.3.6.1.4.1.539.12.3.1.1.7
Selects between ISO and CCITT packet level specifications.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ccittPktLvl(1), isoPktLvl(2)

aix1PktAdminFacilChecking		1.3.6.1.4.1.539.12.3.1.1.8
Enables and disables packet level checking of the facilities field of call processing packets for validity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	checkFacils(1), noCheckFacils(2)

aix1PktAdminUndefinedFacils		1.3.6.1.4.1.539.12.3.1.1.9
Enables and disables packet level allowing undefined facilities to appear in the facilities field of call processing packets.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noUndefFacils(1), undefFacils(2)

aix1PktAdminDefMaxPktSize		1.3.6.1.4.1.539.12.3.1.1.10
The maximum packet size to use for all calls placed on this packet layer entity. If aix1PktAdminNegPktSize is set to negotiate(2), this will be the proposed value for calls placed on the packet level entitry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	pkt128(128), pkt256(256), pkt512(512), pkt1024(1024)

aix1PktAdminDefWindowSize		1.3.6.1.4.1.539.12.3.1.1.11
The maximum packet level window size to use on this PLE. If aix1PktAdminNegWindowSize is set to negotiate(2), this will be the proposed value for calls placed on the packet layer entity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..127

aix1PktAdminNegMaxPktSize		1.3.6.1.4.1.539.12.3.1.1.12
Determines whether this PLE will originate calls which negotiate packet size.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noNegotiation(1), negotiate(2)

aix1PktAdminNegWindowSize		1.3.6.1.4.1.539.12.3.1.1.13
Determines whether this PLE will originate calls which negotiate window size.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noNegotiation(1), negotiate(2)

aix1PktAdminPacketizingTimer		1.3.6.1.4.1.539.12.3.1.1.14
The interval from the time of receipt of the first character from the TDM backplane to transmission of a block of characters to the X.25 protocol stack for transmission in a data packet to the network. In 100ths of a second. This value is not meaningful on backplane connections on which escape framing, TL1 packetizing, or programmable forwarding characters are active.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

aix1PktAdminPVCOffset		1.3.6.1.4.1.539.12.3.1.1.15
Specifies an offset that gets added to the PVC logical channel range specified by x25AdmnMaxActiveCircuits and x25AdmnNumberPVCs from RFC 1382.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

aix1PktAdminSVCOffset		1.3.6.1.4.1.539.12.3.1.1.16
Specifies an offset that gets added to the SVC logical channel range specified by x25AdmnMaxActiveCircuits and x25AdmnNumberPVCs from RFC 1382.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..4095

aix1PktOperTable		1.3.6.1.4.1.539.12.3.2
The table of operational elements which apply to an individual X.25 link at the packet layer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PktOperEntry

aix1PktOperEntry		1.3.6.1.4.1.539.12.3.2.1
The addressing information for one of this X.25 link's packet layer operational objects.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	PktOperEntry

aix1PktOperIndex		1.3.6.1.4.1.539.12.3.2.1.1
The ifIndex value of the packet level associated with these objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1PktOperConformanceMode		1.3.6.1.4.1.539.12.3.2.1.2
The conformance testing mode to which X.25's behavior will adhere. This is the currently operational value.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ccitt(1), ddn(2)

aix1PktOperDBit		1.3.6.1.4.1.539.12.3.2.1.3
Determines whether the packet level will allow the D-bit in call setup packets.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	dbitNotAllowed(1), dbitAllowed(2)

aix1PktOperQBitMBit		1.3.6.1.4.1.539.12.3.2.1.4
Determines whether the packet level will check for consistency in the use of Q and M bits, i. e. that the value of the Q-bit is the same in every packet of an M-bit sequence.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noQMCheck(1), qmCheck(2)

aix1PktOperUseRejectPkts		1.3.6.1.4.1.539.12.3.2.1.5
Enables and disables the use of packet retransmission. If the packet level is acting as a DTE it will send a REJ packet in response to a data packet received out of sequence. If the packet level is acting as a DCE, it will accept a REJ packet and retransmit the requested data packet(s).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noPktRetrans(1), pktRetrans(2)

aix1PktOperSendInitialRestart		1.3.6.1.4.1.539.12.3.2.1.6
Enables and disables sending of an initial restart request packet when the link comes up.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	initialRestart(1), noInitialRestart(2)

aix1PktOperStdsBody		1.3.6.1.4.1.539.12.3.2.1.7
Selects between ISO and CCITT packet level specifications.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ccittPktLvl(1), isoPktLvl(2)

aix1PktOperFacilChecking		1.3.6.1.4.1.539.12.3.2.1.8
Enables and disables packet level checking of the facilities field of call processing packets for validity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	checkFacils(1), noCheckFacils(2)

aix1PktOperUndefinedFacils		1.3.6.1.4.1.539.12.3.2.1.9
Enables and disables packet level allowing undefined facilities to appear in the facilities field of call processing packets.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noUndefFacils(1), undefFacils(2)

aix1PktOperDefMaxPktSize		1.3.6.1.4.1.539.12.3.2.1.10
The maximum packet size to use for all calls placed on this packet layer entity. If aix1PktOperNegPktSize is set to negotiate(2), this will be the proposed value for calls placed on the packett layer entity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	pkt128(128), pkt256(256), pkt512(512), pkt1024(1024)

aix1PktOperDefWindowSize		1.3.6.1.4.1.539.12.3.2.1.11
The maximum packet level window size to use for all calls placed on this packet layer entity. If aix1PktOperNegWindowSize is set to negotiate(2), this will be the proposed value for calls placed on the packet layer entity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..127

aix1PktOperNegMaxPktSize		1.3.6.1.4.1.539.12.3.2.1.12
Determines whether this packet layer entity will originate calls which negotiate packet size.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noNegotiation(1), negotiate(2)

aix1PktOperNegWindowSize		1.3.6.1.4.1.539.12.3.2.1.13
Determines whether this packet layer entity will originate calls which negotiate window size.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noNegotiation(1), negotiate(2)

aix1PktOperPacketizingTimer		1.3.6.1.4.1.539.12.3.2.1.14
The interval from the time of receipt of the first character from the TDM backplane to transmission of a block of characters to the X.25 protocol stack for transmission in a data packet to the network. In 100ths of a second. This value is not meaningful on backplane connections on which escape framing, TL1 packetizing, or programmable forwarding characters are active.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

aix1PktOperPVCOffset		1.3.6.1.4.1.539.12.3.2.1.15
Specifies an offset that gets added to the PVC logical channel range specified by x25AdmnMaxActiveCircuits and x25AdmnNumberPVCs from RFC 1382.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

aix1PktOperSVCOffset		1.3.6.1.4.1.539.12.3.2.1.16
Specifies an offset that gets added to the SVC logical channel range specified by x25AdmnMaxActiveCircuits and x25AdmnNumberPVCs from RFC 1382.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

aix1PktStatTable		1.3.6.1.4.1.539.12.3.3
The table of statistical elements which apply to an individual X.25 link at the packet layer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PktStatEntry

aix1PktStatEntry		1.3.6.1.4.1.539.12.3.3.1
The addressing information for one of this X.25 link's packet layer statistical objects.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	PktStatEntry

aix1PktStatIndex		1.3.6.1.4.1.539.12.3.3.1.1
The ifIndex value of the packet layer entity associated with these objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1PktStatInCharsPerSec80s		1.3.6.1.4.1.539.12.3.3.1.2
The average number of data characters (characters in the data field of X.25 data packets) received from the network per second over the last 80 seconds by this packet layer entity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1PktStatOutCharsPerSec80s		1.3.6.1.4.1.539.12.3.3.1.3
The average number of data characters (characters in the data field of X.25 data packets) transmitted to the network per second over the last 80 seconds by this packet layer entity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1FrmAdminTable		1.3.6.1.4.1.539.12.4.1
The table of administrative elements which apply to an individual X.25 link at the frame layer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrmAdminEntry

aix1FrmAdminEntry		1.3.6.1.4.1.539.12.4.1.1
The addressing information for one of this X.25 link's frame layer administrative objects.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrmAdminEntry

aix1FrmAdminIndex		1.3.6.1.4.1.539.12.4.1.1.1
The ifIndex value of the frame layer entity associated with these objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1FrmAdminIdleRRs		1.3.6.1.4.1.539.12.4.1.1.2
Enables and disables transmission of idle Receive Ready frames by the frame layer.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	idleRRs(1), noIdleRRs(2)

aix1FrmAdminRandomizeT1		1.3.6.1.4.1.539.12.4.1.1.3
Enables and disables the introduction of random jitter into the frame layer's T1 timer to avoid T1 timer synchronization with the remote frame layer.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	randomT1(1), noRandomT1(2)

aix1FrmOperTable		1.3.6.1.4.1.539.12.4.2
The table of operational elements which apply to an individual X.25 link at the frame layer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrmOperEntry

aix1FrmOperEntry		1.3.6.1.4.1.539.12.4.2.1
The addressing information for one of this X.25 link's frame layer operational objects.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FrmOperEntry

aix1FrmOperIndex		1.3.6.1.4.1.539.12.4.2.1.1
The ifIndex value of the frame level associated with these objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1FrmOperIdleRRs		1.3.6.1.4.1.539.12.4.2.1.2
Enables and disables transmission of idle Receive Ready frames by the frame layer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	idleRRs(1), noIdleRRs(2)

aix1FrmOperRandomizeT1		1.3.6.1.4.1.539.12.4.2.1.3
Enables and disables the introduction of random jitter into the frame layer's T1 timer to avoid T1 timer synchronization with the remote frame layer.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	randomT1(1), noRandomT1(2)

aix1PhysAdminTable		1.3.6.1.4.1.539.12.5.1
The table of administrative elements which apply to an individual X.25 link at the physical layer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PhysAdminEntry

aix1PhysAdminEntry		1.3.6.1.4.1.539.12.5.1.1
The addressing information for one of this X.25 link's physical layer administrative objects.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	PhysAdminEntry

aix1PhysAdminIndex		1.3.6.1.4.1.539.12.5.1.1.1
The ifIndex value of the physical port associated with these objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1PhysAdminInterFrameDelayStatus		1.3.6.1.4.1.539.12.5.1.1.2
Enables and disables a delay period between transmitted frames.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ifdDisabled(1), ifdEnabled(2)

aix1PhysAdminInterFrameDelayInterval		1.3.6.1.4.1.539.12.5.1.1.3
Sets the interframe delay interval. This value is effective only if aix1PhysAdminInterFrameDelayStatus is set to ifdEnabled(2). This value is expressed in microseconds, with 100 microsecond granularity (it's truncated to the nearest 100 microseconds).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..7fffffff

aix1PhysAdminT1LineBuildOut		1.3.6.1.4.1.539.12.5.1.1.4
The T1 line build out value. The specified syntax represents ranges of line length expressed in feet.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	lbo0to133(1), lbo133to266(2), lbo266to399(3), lbo399to533(4), lbo533to655(5)

aix1PhysOperTable		1.3.6.1.4.1.539.12.5.2
The table of operational elements which apply to an individual X.25 link at the physical layer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PhysOperEntry

aix1PhysOperEntry		1.3.6.1.4.1.539.12.5.2.1
The addressing information for one of this X.25 link's physical layer operational objects.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	PhysOperEntry

aix1PhysOperIndex		1.3.6.1.4.1.539.12.5.2.1.1
The ifIndex value of the physical port associated with these objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1PhysOperInterFrameDelayStatus		1.3.6.1.4.1.539.12.5.2.1.2
Enables and disables a delay period between transmitted frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ifdDisabled(1), ifdEnabled(2)

aix1PhysOperInterFrameDelayInterval		1.3.6.1.4.1.539.12.5.2.1.3
Sets the interframe delay interval. This value is effective only if aix1PhysAdminInterFrameDelayStatus is set to ifdEnabled(2). This value is expressed in microseconds, with 100 microsecond granularity (it's truncated to the nearest 100 microseconds).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..7fffffff

aix1PhysOperT1LineBuildOut		1.3.6.1.4.1.539.12.5.2.1.4
The T1 line build out value. The specified syntax represents ranges of line length expressed in feet.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	lbo0to133(1), lbo133to266(2), lbo266to399(3), lbo399to533(4), lbo533to655(5)

aix1PhysStatTable		1.3.6.1.4.1.539.12.5.3
The table of statistical elements which apply to an individual X.25 link at the physical layer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PhysStatEntry

aix1PhysStatEntry		1.3.6.1.4.1.539.12.5.3.1
The addressing information for one of this X.25 link's physical layer statistical objects.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	PhysStatEntry

aix1PhysStatIndex		1.3.6.1.4.1.539.12.5.3.1.1
The ifIndex value of the physical port associated with these objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1PhysStatTxAborts		1.3.6.1.4.1.539.12.5.3.1.2
The number of abort sequences transmitted on the serial interfaces. This is a proprietary object because the RS232-like MIB (RFC 1659) doesn't define a similar object! RFC 1659 defines a counter for receive aborts, but not transmit aborts.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1CircuitTable		1.3.6.1.4.1.539.12.6.1
The table of objects which maps logical channel number and packet level ifIndex number to Virtual Connection(VC) number.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CircuitEntry

aix1CircuitEntry		1.3.6.1.4.1.539.12.6.1.1
The addressing information for the VC Circuit table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CircuitEntry

aix1CircuitLinkId		1.3.6.1.4.1.539.12.6.1.1.1
The ifindex value of the packet layer entity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1CircuitChannelNumber		1.3.6.1.4.1.539.12.6.1.1.2
X.25 logical channel number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

aix1CircuitState		1.3.6.1.4.1.539.12.6.1.1.3
The call processing state of the local Virtual Connection. This is not a standard packet level state. This is the call processing state of the AI version 7 system firmware that mediates between the X.25 protocol stack and AISwitch internal connection mechanisms.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), active(2), csCall(3), csDisco(4), csCancel(5), csReject(6), csCol(7), csUncol(8), npCall(9), npDisco(10), npCancel(11), npReject(12), npCol(13), npUncol(14), trapped(15), csSuspend(16)

aix1CircuitConType		1.3.6.1.4.1.539.12.6.1.1.4
The type of connection currently supported by the VC.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	lmux(1), rmux(2), debug(5), background(6), pvc(11), svc(12)

aix1CircuitBCNumber		1.3.6.1.4.1.539.12.6.1.1.5
The number of the Bus Connection with which this VC is associated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..31

aix1CircuitUserData		1.3.6.1.4.1.539.12.6.1.1.6
The user data that was sent or received in the call request.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

aix1CircuitRemoteBasePort		1.3.6.1.4.1.539.12.6.1.1.7
The baseport of the card to which the SLC is connected across the backplane. This value is meaningful only when this VC is multiplexed to the other SLC. If not, the value returned is -1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	-1..256

aix1CircuitRemoteVCNumber		1.3.6.1.4.1.539.12.6.1.1.8
The Virtual Connection number of the VC on the remote SLC to which this VC is connected. This value is meaningful only on multiplexed VCs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..ffff

aix1CircuitPktsSent		1.3.6.1.4.1.539.12.6.1.1.9
The number of packets sent to the packet level by the AI version 7 system software. This counts all kinds of packets, not just data packets.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1CircuitPktsRcvd		1.3.6.1.4.1.539.12.6.1.1.10
The number of packets received from the packet level by the AI version 7 system software. This counts all kinds of packets, not just data packets.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1CircuitOperPVCType		1.3.6.1.4.1.539.12.6.1.1.11
Defines the relationship between a PVC and the connection-oriented AISwitch TDM backplane. The three types represented are defined as follows: Active: initiates connections across the backplane at an interval defined by the timer. Passive: waits to respond to a connection attempt across the backplane. Uses timer to wait for reset confirm from network. Accepts backplane connection if it receives reset confirmation in time. Connect on Activity: initiates connection across backplane upon the receipt of data from the network. Forwards received data once connection is established. Disconnects backplane connection if a timer interval passes with no data activity in either direction. This object will return the value none(1) if the value of aix1CircuitConType for this VC is not pvc(11). This object reflects the current operational value of this parameter. Note that unlike most operational objects, it is writable. If the value of this object is changed, it modifies the current behavior of the board, but is not saved in nonvolatile memory.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), active(2), connectOnActivity(3), passive(4)

aix1CircuitOperPVCTimer		1.3.6.1.4.1.539.12.6.1.1.12
Defines the timer interval, in seconds used to manage the PVC's relationship with an internal backplane connection. The timer is used for different purposes depending on the value of aix1VCPVCType as described above. This object will return the value 0 if the VC in question is not associated with a PVC. This object reflects the current operational value of this parameter. Note that unlike most operational objects, it is writable. If the value of this object is changed, it modifies the current behavior of the board, but is not saved in nonvolatile memory.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..600

aix1VCTable		1.3.6.1.4.1.539.12.6.2
The table of objects containing information pertaining to Virtual Connections(VC).
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VCEntry

aix1VCEntry		1.3.6.1.4.1.539.12.6.2.1
The addressing information for the VC table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	VCEntry

aix1VCVCNumber		1.3.6.1.4.1.539.12.6.2.1.1
The local Virtual Connection number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..287

aix1VCState		1.3.6.1.4.1.539.12.6.2.1.2
The call processing state of the local Virtual Connection. This is not a standard packet level state. This is the call call processing state of the AI version 7 system firmware that mediates between the X.25 protocol stack and AISwitch internal connection mechanisms.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), active(2), csCall(3), csDisco(4), csCancel(5), csReject(6), csCol(7), csUncol(8), npCall(9), npDisco(10), npCancel(11), npReject(12), npCol(13), npUncol(14), trapped(15), csSuspend(16)

aix1VCConType		1.3.6.1.4.1.539.12.6.2.1.3
The type of connection currently supported by the VC.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	lmux(1), rmux(2), debug(5), background(6), pvc(11), svc(12)

aix1VCBCNumber		1.3.6.1.4.1.539.12.6.2.1.4
The number of the Bus Connection with which this VC is associated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..31

aix1VCUserData		1.3.6.1.4.1.539.12.6.2.1.5
The user data that was sent or received in the call request.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

aix1VCRemoteBasePort		1.3.6.1.4.1.539.12.6.2.1.6
The baseport of the card to which the SLC is connected across the backplane. This value is meaningful only when this VC is multiplexed to the other SLC. If not, the value returned is -1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	-1..256

aix1VCRemoteVCNumber		1.3.6.1.4.1.539.12.6.2.1.7
The Virtual Connection number of the VC on the remote SLC to which this VC is connected. This value is meaningful only on multiplexed VCs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..ffff

aix1VCPktsSent		1.3.6.1.4.1.539.12.6.2.1.8
The number of packets sent to the packet level by the AI version 7 system software. This counts all kinds of packets, not just data packets.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1VCPktsRcvd		1.3.6.1.4.1.539.12.6.2.1.9
The number of packets received from the packet level by the AI version 7 system software. This counts all kinds of packets, not just data packets.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter32

aix1VCOperPVCType		1.3.6.1.4.1.539.12.6.2.1.10
Defines the relationship between a PVC and the connection-oriented AISwitch TDM backplane. The three types represented are defined as follows: Active: initiates connections across the backplane at an interval defined by the timer. Passive: waits to respond to a connection attempt across the backplane. Uses timer to wait for reset confirm from network. Accepts backplane connection if it receives reset confirmation in time. Connect on Activity: initiates connection across backplane upon receipt of data from network. Forwards received data once connection is established. Disconnects backplane connection if a timer interval passes with no data activity in either direction. This object will return the value none(1) if the value of aix1VCConType for this VC is not pvc(11). This object reflects the current operational value of this parameter. Note that unlike most operational objects, it is writable. If the value of this object is changed, it modifies the current behavior of the board, but is not saved in nonvolatile memory.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), active(2), connectOnActivity(3), passive(4)

aix1VCOperPVCTimer		1.3.6.1.4.1.539.12.6.2.1.11
Defines the timer interval, in seconds used to manage the PVC's relationship with an internal backplane connection. The timer is used for different purposes depending on the value of aix1VCPVCType as described above. This object will return the value 0 if the VC in question question is not associated with a PVC. This object reflects the current operational value of this parameter. Note that unlike most operational objects, it is writable. If the value of this object is changed, it modifies the current behavior of the board, but is not saved in nonvolatile memory.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..600

aix1AdminPVCTable		1.3.6.1.4.1.539.12.6.3
The table of objects which control attributes of PVCs configured, but not necessarily in effect.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AdminPVCEntry

aix1AdminPVCEntry		1.3.6.1.4.1.539.12.6.3.1
The addressing information for the PVC Admin table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AdminPVCEntry

aix1AdminPVCLinkId		1.3.6.1.4.1.539.12.6.3.1.1
The ifindex value of the packet layer entity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IfIndexType

aix1AdminPVCChannelNumber		1.3.6.1.4.1.539.12.6.3.1.2
X.25 logical channel number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

aix1AdminPVCType		1.3.6.1.4.1.539.12.6.3.1.3
Defines the relationship between a PVC and the connection-oriented AISwitch TDM backplane. The three types represent are defined as follows: Active: initiates connections across the backplane at an interval defined by the timer. Passive: waits to respond to a connection attempt across the backplane. Uses timer to wait for reset confirm from network. Accepts the backplane connection if it receives reset confirmation in time. Connect on Activity: initiates connection across backplane upon receipt of data from network. Forwards received data once connection is established. Disconnects backplane connection if a timer interval passes with no data activity in either direction. This object will return the value none(1) if aix1AdminPVCChannelNumber doesn't correspond to a channel in the range specified by the combination of x25admnNumberPVCs and aix1PktAdminPVCOffset for the link specified by aix1AdminPVCLinkID. This object is settable, but does not reflect the mandatory operational value of this parameter.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), active(2), connectOnActivity(3), passive(4)

aix1AdminPVCTimer		1.3.6.1.4.1.539.12.6.3.1.4
Defines the timer interval, in seconds used to manage the PVC's relationship with an internal backplane connection. The timer is used for different purposes depending on the value of aix1VCPVCType as described above. This object will return the value 0 if aix1AdminPVCChannelNumber doesn't correspond to a channel in the range specified by the combination of x25admnNumberPVCs and aix1PktAdminPVCOffset for the link specified by aix1AdminPVCLinkID. This object is settable, but does not reflect the mandatory operational value of this parameter.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..600

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor