ALCATEL-IND1-AUTO-FABRIC-MIB
File:
ALCATEL-IND1-AUTO-FABRIC-MIB.mib (18922 bytes)
Imported modules
Imported symbols
Defined Types
AlaAutoFabricPortConfigEntry |
|
SEQUENCE |
|
|
|
|
alaAutoFabricPortConfigIfIndex |
InterfaceIndex |
|
|
alaAutoFabricPortConfigStatus |
INTEGER |
|
|
alaAutoFabricPortLACPProtocolStatus |
INTEGER |
|
|
alaAutoFabricPortSPBProtocolStatus |
INTEGER |
|
|
alaAutoFabricPortMVRPProtocolStatus |
INTEGER |
|
|
alaAutoFabricPortStatus |
INTEGER |
|
Defined Values
alcatelIND1AUTOFABRICMIB |
1.3.6.1.4.1.6486.801.1.2.1.75.1 |
This module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
For the Birds Of Prey Product Line
AUTOFABRIC for automatic detection and configuration of LACP, SPB and MVRP.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2002 Alcatel Internetworking, Incorporated
ALL RIGHTS RESERVED WORLDWIDE |
MODULE-IDENTITY |
|
|
|
alcatelIND1AUTOFABRICMIBObjects |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1 |
Branch For AUTO-FABRIC
Subsystem Managed Objects. |
Status: current |
Access: read-only |
OBJECT-IDENTITY |
|
|
|
alcatelIND1AUTOFABRICMIBGroups |
1.3.6.1.4.1.6486.801.1.2.1.75.1.2.1 |
Branch for AUTOFABRIC Module MIB Subsystem Units of Conformance. |
Status: current |
Access: read-only |
OBJECT-IDENTITY |
|
|
|
alcatelIND1AUTOFABRICMIBCompliances |
1.3.6.1.4.1.6486.801.1.2.1.75.1.2.2 |
Branch for AUTOFABRIC Module MIB Subsystem Compliance Statements. |
Status: current |
Access: read-only |
OBJECT-IDENTITY |
|
|
|
alaAutoFabricGlobalStatus |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.1 |
This variable is used to enable or diable Autofabric on the switch.
The value enable (1) indicates that Autofabric should be enabled on
the switch. The value disable (2) is used to disable Autofabric on
the switch. By default, Autofabric is enabled on the switch. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaAutoFabricGlobalDiscovery |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.2 |
Defines the global discovery window control for Autofabric.
The value restart (2) indicates that Autofabric should restart
global discovery window.
By default, this object contains a zero value. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
default(1), restart(2) |
|
alaAutoFabricGlobalLACPProtocolStatus |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.3 |
This variable is used to enable or diable AutoFabric LACP discovery.
on the switch. The value enable (1) indicates that during discovery
the switch will attempt to create LACP link aggregates. The value
disable (2) indicates that there would be no attempt to create LACP
link aggregates during the discovery phase. By default LACP is enabled
on the switch |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaAutoFabricGlobalSPBProtocolStatus |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.4 |
This variable is used to enable or diable AutoFabric SPB discovery.
on the switch. The value enable (1) indicates that during discovery
the switch will attempt to create SPB adjacencies. The value
disable (2) indicates that there would be no attempt to create SPB
adjacencies during the discovery phase. By default SPB is enabled
on the switch |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaAutoFabricGlobalMVRPProtocolStatus |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.5 |
This variable is used to enable or diable AutoFabric MVRP discovery.
on the switch. The value enable (1) indicates that during discovery
the switch will enable MVRP and attempt to propagate and learn VLANs.
The value disable (2) indicates that MVRP would not be enabled in
discovery phase. By default MVRP is enabled on the switch |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaAutoFabricGlobalConfigSaveTimer |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.6 |
Maximum period of time after which configuration built up by AutoFabric
would get written to the boot.cfg or vcboot.cfg.
The range supported is 60-3600 seconds. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
60..3600 |
|
alaAutoFabricGlobalConfigSaveTimerStatus |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.7 |
This variable is used to enable or diable AutoFabric config save
timer on the switch. The value enable (1) indicates that
after the expiry of the config save timer, all AutoFabric
configurations would get written to the boot.cfg ot the vcboot.cfg
The value disable (2) would disable the config save timer.
By default it is enabled |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaAutoFabricGlobalDiscoveryTimer |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.8 |
This variable is used to specify auto-fabric auto
discovery interval, zero disables it, configurable
Value is from 1 to 3600 minutes. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..3600 |
|
alaAutoFabricRemoveGlobalConfig |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.10 |
This variable is used to remove the auto fabric global configuration when the user chooses to disable auto fabric |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
default(1), removeGlobalConfig(2) |
|
alaAutoFabricPortConfigEntry |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.9.1.1 |
An AutoFabric port configuration entry. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AlaAutoFabricPortConfigEntry |
|
|
alaAutoFabricPortConfigStatus |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.9.1.1.2 |
This variable is used to enable or diable AutoFabric on the interface.
The value enable (1) indicates that AutoFabric should be enabled on
the interface. The value disable (2) is used to disable AutoFabric on
the interface. By default, AutoFabric is enabled on the interface. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaAutoFabricPortLACPProtocolStatus |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.9.1.1.3 |
This variable is used to enable LACP in the AutoFabric discovery
on this port. The value enable (1) indicates during discovery window
this port will attempt to form LACP link aggregates. The value disable (2)
indicates this port will not participate in LACP discovery phase.
By default it is enabled |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaAutoFabricPortSPBProtocolStatus |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.9.1.1.4 |
This variable is used to enable SPB in the AutoFabric discovery
on this port. The value enable (1) indicates during discovery window
this port will attempt to form SPB adjacencies. The value disable (2)
indicates this port will not participate in SPB discovery phase.
By default it is enabled |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaAutoFabricPortMVRPProtocolStatus |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.9.1.1.5 |
This variable is used to enable MVRP in the AutoFabric discovery
on this port. The value enable (1) indicates during discovery window
this port will enable MVRP and attempt to learn and propagate VLANs.
The value disable (2) indicates this port will not participate in MVRP
discovery phase.
By default it is enabled |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaAutoFabricPortStatus |
1.3.6.1.4.1.6486.801.1.2.1.75.1.1.9.1.1.6 |
The state of the Autofabric discovery window on the port. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
disabled(1), pending(2), complete(3) |
|
alaAutoFabricBaseGroup |
1.3.6.1.4.1.6486.801.1.2.1.75.1.2.1.1 |
Collection of objects for management of AutoFabric Base Group. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
alaAutoFabricPortConfigGroup |
1.3.6.1.4.1.6486.801.1.2.1.75.1.2.1.2 |
Collection of objects for management of AutoFabric Port Configuration Table. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|