ALCATEL-IND1-E-SERVICE-MIB

File: ALCATEL-IND1-E-SERVICE-MIB.mib (58308 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	ALCATEL-IND1-BASE
SNMPv2-TC	IF-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-IDENTITY	OBJECT-TYPE
Integer32	Counter64	OBJECT-GROUP
MODULE-COMPLIANCE	softentIND1eService	RowStatus
TEXTUAL-CONVENTION	DisplayString	MacAddress
InterfaceIndex

Defined Types

AlaEServiceUNIProfileProtocolTreatment
The behavior of the bridge in regards to the given protocols packets received on the UNI. Tunnel (1) enables the packets to be tunneled across the provider network. Discard (2) causes the packets to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling.
TEXTUAL-CONVENTION
	INTEGER	tunnel(1), drop(2), peer(3), macTunnel(4)

AlaEServiceSapProfileEntry
SEQUENCE
	alaEServiceSapProfileID	DisplayString
	alaEServiceSapProfileCVLANTreatment	INTEGER
	alaEServiceSapProfileReplacementCVLAN	INTEGER
	alaEServiceSapProfilePriorityMapMode	INTEGER
	alaEServiceSapProfileFixedPriority	INTEGER
	alaEServiceSapProfileIngressBW	Integer32
	alaEServiceSapProfileBandwidthShare	INTEGER
	alaEServiceSapProfileRowStatus	RowStatus
	alaEServiceSapProfileEgressBW	Integer32
	alaEServiceSapProfileCIR	Integer32
	alaEServiceSapProfileCBS	Integer32
	alaEServiceSapProfilePIR	Integer32
	alaEServiceSapProfilePBS	Integer32

AlaEServiceUNIProfileEntry
SEQUENCE
	alaEServiceUNIProfileID	DisplayString
	alaEServiceUNIProfileStpBpduTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfile8021xTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfile8021ABTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfile8023adTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileGvrpTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileAmapTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileRowStatus	RowStatus
	alaEServiceUNIProfileMvrpTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileTunnelMac	MacAddress
	alaEServiceUNIProfileLacpMarkerTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileOamTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileCiscoPagpTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileCiscoUdldTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileCiscoCdpTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileCiscoVtpTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileCiscoDtpTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileCiscoPvstTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileCiscoVlanTreatment	AlaEServiceUNIProfileProtocolTreatment
	alaEServiceUNIProfileCiscoUplinkTreatment	AlaEServiceUNIProfileProtocolTreatment

AlaEServiceEntry
SEQUENCE
	alaEServiceID	DisplayString
	alaEServiceSVLAN	INTEGER
	alaEServiceVlanType	INTEGER
	alaEServiceRowStatus	RowStatus
	alaEServiceStatGreenCount	Counter64
	alaEServiceStatYellowCount	Counter64
	alaEServiceStatRedCount	Counter64

AlaEServiceSapEntry
SEQUENCE
	alaEServiceSapID	Integer32
	alaEServiceSapServiceID	DisplayString
	alaEServiceSapProfile	DisplayString
	alaEServiceSapRowStatus	RowStatus

AlaEServiceSapCvlanEntry
SEQUENCE
	alaEServiceSapCvlanSapID	Integer32
	alaEServiceSapCvlanCvlan	INTEGER
	alaEServiceSapCvlanMapType	INTEGER
	alaEServiceSapCvlanRowStatus	RowStatus

AlaEServicePortEntry
SEQUENCE
	alaEServicePortID	InterfaceIndex
	alaEServicePortType	INTEGER
	alaEServicePortVendorTpid	Integer32
	alaEServicePortLegacyStpBpdu	INTEGER
	alaEServicePortLegacyGvrpPdu	INTEGER
	alaEServicePortUniProfile	DisplayString
	alaEServicePortTransBridging	INTEGER
	alaEServicePortLegacyMvrpPdu	INTEGER

AlaEServiceSapUniEntry
SEQUENCE
	alaEServiceSapUniSap	Integer32
	alaEServiceSapUniUni	InterfaceIndex
	alaEServiceSapUniRowStatus	RowStatus

AlaEServiceNniSvlanEntry
SEQUENCE
	alaEServiceNniSvlanNni	InterfaceIndex
	alaEServiceNniSvlanSvlan	INTEGER
	alaEServiceNniSvlanRowStatus	RowStatus
	alaEServiceNniSvlanVpaType	INTEGER

AlaEServiceSapCvlanPortStatEntry
SEQUENCE
	alaEServiceSapCvlanPortStatSapID	Integer32
	alaEServiceSapCvlanPortStatCvlanID	INTEGER
	alaEServiceSapCvlanPortStatPortID	InterfaceIndex
	alaEServiceSapCvlanPortStatGreenCount	Counter64
	alaEServiceSapCvlanPortStatYellowCount	Counter64
	alaEServiceSapCvlanPortStatRedCount	Counter64

Defined Values

alcatelIND1EServiceMIB		1.3.6.1.4.1.6486.801.1.2.1.50.1
The parameters for configuration of the E-Service feature. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2006 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
MODULE-IDENTITY

alcatelIND1eServiceMIBObjects		1.3.6.1.4.1.6486.801.1.2.1.50.1.1
Branch For E-Service Managed Objects.
Status: current	Access: read-only
OBJECT-IDENTITY

alcatelIND1EServiceMIBConformance		1.3.6.1.4.1.6486.801.1.2.1.50.1.2
Branch For E-Service Conformance Information.
Status: current	Access: read-only
OBJECT-IDENTITY

alcatelIND1EServiceMIBGroups		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1
Branch For E-Service Units Of Conformance.
Status: current	Access: read-only
OBJECT-IDENTITY

alcatelIND1EServiceMIBCompliances		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.2
Branch For E-Service Compliance Statements.
Status: current	Access: read-only
OBJECT-IDENTITY

alaEService		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1
OBJECT IDENTIFIER

alaEServiceInfo		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.1
OBJECT IDENTIFIER

alaEServiceMode		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.1.1
The current mode configured for Vlan Stacking and Layer 2 tunnel configuration. legacyMode (1) indicates that the commands from AlcatelIND1VLANStacking.mib are to be used. eServiceMode (2) indicates the commands from this MIB are to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	legacyMode(1), eServiceMode(2)

alaEServiceStatReset		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.1.2
Defines the global clear statistics control for ethernet-service counters. default(0) - default value for this object, reset(1) - indicates that all ethernet-service counters should be cleared.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	default(0), reset(1)

alaEServiceSapProfileTable		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2
A table that contains service profiles containing performance and control attributes. An entry in this table is created when a new service profile is defined.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaEServiceSapProfileEntry

alaEServiceSapProfileEntry		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1
A E-Service Service Profile entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaEServiceSapProfileEntry

alaEServiceSapProfileID		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.1
A label given to uniquely identify this profile. Must be at least one character long.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..31)

alaEServiceSapProfileCVLANTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.2
The type of VLAN stacking operation to be performed on a customer frame entering this service. Stack Svlan (1) indicates that the SVLAN is to be pre-pended on the frame before any existing 802.1Q tag. Translate (2) means to replace the existing 802.1Q tag with the SVLAN. Change CVLAN (3) indicates that the customer tag is to remain on the frame but its value is to be changed to the supplied value.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	stackSVLAN(1), translate(2), changeCVLAN(3)

alaEServiceSapProfileReplacementCVLAN		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.3
The CVLAN ID to use when using the Change CVLAN treatment mode.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..4094

alaEServiceSapProfilePriorityMapMode		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.4
This object describes the source of the value for the priority field of the SVLAN 802.1Q tag when pre-pended to the customer data frame. If set to notAssigned(0), SAP priority limit parameter will not be effective, QoS priority settings needs to be configured. mapInnerPtoOuterP (1) uses the priority field of the incoming frame when tagged to fill in the priority field of the SVLAN tag. mapInnerDscpToOuterP (2) uses the frames priority bits in its IP DSCP field to fill in the priority field of the SVLAN tag. FixedP (3) uses the supplied FixedPriorityValue to fill in the SVLAN tag priority bits.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notAssigned(0), mapInnerPtoOuterP(1), mapInnerDscpToOuterP(2), fixedP(3)

alaEServiceSapProfileFixedPriority		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.5
This object describes the value of the priority field of the 802.1Q SVLAN tag pre-pended to customer data frames when the fixed priority mapping mode is selected.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..7

alaEServiceSapProfileIngressBW		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.6
This object describes this limit of ingress bandwidth for the traffic to which this profile is applied. If 0, no bandwidth limit is applied. This number represents traffic in units of 1,000,000 bits per second. Note that all CVLAN that belong to this SAP will share this aggregated limit.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

alaEServiceSapProfileBandwidthShare		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.7
This object describes the use of the bandwidth limit in how it is applied across multiple ports of the SAP. If set to notApplicable(0), the SAP is not used. If set to Shared (1), all the ports that are part of the SAP will use aggregated bandwidth, sharing some part of the bandwidth limit. If set to notShared (2), each port will use its own bandwidth meter for this SAP. This value is not used if ingressBandwidth is 0. If set to notAssigned(3), SAP bandwidth limit parameter will not be effective, QoS bandwith settings needs to be configured.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(0), shared(1), notShared(2), notAssigned(3)

alaEServiceSapProfileRowStatus		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.8
The status of this table entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaEServiceSapProfileEgressBW		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.9
This object describes this limit of egress bandwidth for each UNI of the SAP to which this profile is applied. If 0, no bandwidth limit is applied. This number represents traffic in units of Megabits per second. Note that all CVLAN that belong to this SAP will share this aggregated limit.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

alaEServiceSapProfileCIR		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.10
Committed Information Rate - bandwidth values in bits per second.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

alaEServiceSapProfileCBS		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.11
Committed Burst Size - bucket size in byte.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

alaEServiceSapProfilePIR		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.12
Peak Information Rate - bandwidth values in bits per second.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

alaEServiceSapProfilePBS		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.2.1.13
Peak Burst Size - bucket size in byte.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

alaEServiceUNIProfileTable		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3
A table that contains service profiles containing performance and control attributes. An entry in this table is created when a new service profile is defined.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaEServiceUNIProfileEntry

alaEServiceUNIProfileEntry		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1
A E-Service Service Profile entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaEServiceUNIProfileEntry

alaEServiceUNIProfileID		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.1
A label given to uniquely identify this profile. Must be at least one character long.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..31)

alaEServiceUNIProfileStpBpduTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.2
This object describes the behavior of the bridge in regards to the spanning tree protocol BPDU received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling.
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfile8021xTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.3
This object describes the behavior of the bridge in regards to the IEEE 802.1x PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling.
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfile8021ABTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.4
This object describes the behavior of the bridge in regards to the IEEE 802.1AB PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling.
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfile8023adTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.5
This object describes the behavior of the bridge in regards to the IEEE 802.1ad PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling.
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileGvrpTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.6
This object describes the behavior of the bridge in regards to the GVRP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling.
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileAmapTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.7
This object describes the behavior of the bridge in regards to the Alcatel propietary AMAP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currenly mac-tunnel is not supported
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileRowStatus		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.8
The status of this table entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaEServiceUNIProfileMvrpTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.9
This object describes the behavior of the bridge in regards to the MVRP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Currently peer is not supported for MVRP
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileTunnelMac		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.10
This object specifies the tunnel mac used to tunnel L2 protocol to NNI ports
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

alaEServiceUNIProfileLacpMarkerTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.11
This object describes the behavior of the bridge in regards to the LACP MARKER PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling.
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileOamTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.12
This object describes the behavior of the bridge in regards to the OAM PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling.
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileCiscoPagpTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.13
This object describes the behavior of the bridge in regards to the PAGP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer is not supported
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileCiscoUdldTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.14
This object describes the behavior of the bridge in regards to the UDLD PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling.
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileCiscoCdpTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.15
This object describes the behavior of the bridge in regards to the CDC PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer is not supported
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileCiscoVtpTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.16
This object describes the behavior of the bridge in regards to the VTP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer is not supported
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileCiscoDtpTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.17
This object describes the behavior of the bridge in regards to the DTP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer not supported
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileCiscoPvstTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.18
This object describes the behavior of the bridge in regards to the PVST PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer not supported
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileCiscoVlanTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.19
This object describes the behavior of the bridge in regards to the VLAN PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer not supported
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceUNIProfileCiscoUplinkTreatment		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.3.1.20
This object describes the behavior of the bridge in regards to the UPLINK PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel(4) enables mac-tunnelling. Currently peer not supported.
Status: current	Access: read-create
OBJECT-TYPE
	AlaEServiceUNIProfileProtocolTreatment

alaEServiceTable		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.4
A table that contains the services and their assigned SVLAN for the E-Service feature.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaEServiceEntry

alaEServiceEntry		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.4.1
The svlan/ipmvlan-port association.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaEServiceEntry

alaEServiceID		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.4.1.1
A label given to uniquely identify this Service. Must be at least one character long.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..32)

alaEServiceSVLAN		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.4.1.2
The SVLAN number of the SVLAN chosen to the be transport for this service.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..4094

alaEServiceVlanType		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.4.1.3
The type of the vlan this service is going to attach to. When creating the service, the type should match the vlanId specified in the request.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	unknown(0), svlan(1), ipmvlan(2)

alaEServiceRowStatus		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.4.1.4
The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a service. When creating or deleting the service, the user needs to provide both the svlan and the vlantype objects.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaEServiceStatGreenCount		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.4.1.5
Counter for the number of packets/bytes being Green compliant (i.e. in case of srTCM and trTCM, packet is CIR/CBS compliant).
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

alaEServiceStatYellowCount		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.4.1.6
Counter for the number of packets/bytes being Yellow compliant (i.e. in case of srTCM and trTCM, packet is PIR/PBS compliant).
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

alaEServiceStatRedCount		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.4.1.7
Counter for the number of packets/bytes being Red compliant (i.e. in case of srTCM and trTCM, packet is neither CIR/CBS nor PIR/PBS compliant).
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

alaEServiceSapTable		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.5
A table that contains the Service Access Points (Sap) listed by ID. This table is used to create, delete, and modify the SAP's profile
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaEServiceSapEntry

alaEServiceSapEntry		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.5.1
The list of SAP.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaEServiceSapEntry

alaEServiceSapID		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.5.1.1
A Number given to uniquely identify the SAP.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

alaEServiceSapServiceID		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.5.1.2
A label given to uniquely identify the Service this SAP is for. Must be at least one character long.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..32)

alaEServiceSapProfile		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.5.1.3
The string identifying the SAP Profile this sap is to use. If specified, must match an existing SAP Profile.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..32)

alaEServiceSapRowStatus		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.5.1.4
The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a sap. When creating the sap, the user needs to provide the service name in the same set request.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaEServiceSapCvlanTable		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.6
A table that contains the Service Access Points (Sap) where the CVLANs are bound to their service.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaEServiceSapCvlanEntry

alaEServiceSapCvlanEntry		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.6.1
The CVLAN to Sap binding.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaEServiceSapCvlanEntry

alaEServiceSapCvlanSapID		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.6.1.1
A Number given to uniquely identify this SAP.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

alaEServiceSapCvlanCvlan		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.6.1.2
This object is the CVLAN ID that this binding is targeted at. The CVLAN ID may be 0, which indicates an all or untagged only mapping type.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4094

alaEServiceSapCvlanMapType		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.6.1.3
This object is the mapping type that defines what CVLANs are mapped into this service. Multiple mappings can be defined for CVLAN to service, however only one all (2) or untaggedOnly (3) mapping entry can be created per UNI. A mapping type of Single (1) denotes a specific CVLAN value to bind to the service. A mapping type of All (2) denotes that all customer frames that do not map to any other SAP, will be mapped into this service. A mapping type of Untagged (3) denotes that only the untagged frames will be mapped into this service.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	single(1), all(2), untaggedOnly(3)

alaEServiceSapCvlanRowStatus		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.6.1.4
The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a SAP.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaEServicePortTable		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.7
A table that contains the ports used by the EService feature. Both UNI and NNI are listed here.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaEServicePortEntry

alaEServicePortEntry		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.7.1
The list of ports being used by EService.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaEServicePortEntry

alaEServicePortID		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.7.1.1
The IfIndex of this UNI or NNI Port.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

alaEServicePortType		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.7.1.2
The type of port for Vlan Stacking operation. uni (1) represents a customer facing port on which traffic may enter the E-Service. nni (2) respresents a provider network port over which the E-Service may be connected.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	uni(1), nni(3)

alaEServicePortVendorTpid		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.7.1.3
he TPID for this port if type is NNI. It is used for the incoming data traffic parsing and it is substituted to the 802.1Q standard Tpid for the outgoing data traffic. This is used for compatibility with other vendor equipment. The default value is the standard value 0x8100.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

alaEServicePortLegacyStpBpdu		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.7.1.4
The legacy STP BPDU treatment for this port if NNI. It defines the type of processing applied to STP legacy BPDUs on network ports. Legacy BPDU refer to conventional/customer BPDUs with MAC address 01:80:c2:00:00:00 and its processing on network ports can be enabled/disabled by this object.By default the value is disabled i.e provider MAC BPDU with MAC address 01:80:c2:00:00:08 would be processed at network ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(0), enable(1), disable(2)

alaEServicePortLegacyGvrpPdu		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.7.1.5
The legacy GVRP PDU treatment for this port if NNI. It defines the type of processing applied to GVRP PDUs on network ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(0), enable(1), disable(2)

alaEServicePortUniProfile		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.7.1.6
The label of an existing UNI profile that which contains various properties to be applied to this port if UNI.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..31)

alaEServicePortTransBridging		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.7.1.7
The Transparent Bridging status for the nni Port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

alaEServicePortLegacyMvrpPdu		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.7.1.8
The legacy MVRP PDU treatment for this port if NNI. It defines the type of processing applied to MVRP PDUs on network ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(0), enable(1), disable(2)

alaEServiceSapUniTable		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.8
A table that contains the UNI that are bound to each SAP for classifying traffic into each EService. Not that writing to this table may create a new UNI.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaEServiceSapUniEntry

alaEServiceSapUniEntry		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.8.1
The list of SAP-UNI bindings being used by EService.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaEServiceSapUniEntry

alaEServiceSapUniSap		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.8.1.1
The SAP ID that is configured onto this port.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

alaEServiceSapUniUni		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.8.1.2
The IfIndex of this UNI Port.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

alaEServiceSapUniRowStatus		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.8.1.3
The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a binding
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaEServiceNniSvlanTable		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.9
A table that contains the SVLANs bound to each NNI for use by the EService feature.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaEServiceNniSvlanEntry

alaEServiceNniSvlanEntry		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.9.1
The list of NNI-SVLAN bindings being used by EService.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaEServiceNniSvlanEntry

alaEServiceNniSvlanNni		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.9.1.1
The IfIndex of this NNI Port.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

alaEServiceNniSvlanSvlan		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.9.1.2
The SVLAN bound to this port. SVLAN cannot be 1.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	2..4094

alaEServiceNniSvlanRowStatus		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.9.1.3
The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a binding
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaEServiceNniSvlanVpaType		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.9.1.4
The object is used to specify whether the VPA state is to be controlled by an ERP or a STP. By default VPA state is controlled by STP.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	stp(1), erp(2)

alaEServiceSapCvlanPortStatTable		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.10
A statistics table that contains the counters per SAP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaEServiceSapCvlanPortStatEntry

alaEServiceSapCvlanPortStatEntry		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.10.1
A E-Service Statistics Entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaEServiceSapCvlanPortStatEntry

alaEServiceSapCvlanPortStatSapID		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.10.1.1
A Number given to uniquely identify the SAP.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

alaEServiceSapCvlanPortStatCvlanID		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.10.1.2
This object is the CVLAN ID that this binding is targeted at. The CVLAN ID may be 0, which indicates an all or untagged only mapping type.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..4094

alaEServiceSapCvlanPortStatPortID		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.10.1.3
The IfIndex of this UNI Port.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

alaEServiceSapCvlanPortStatGreenCount		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.10.1.4
Counter for the number of packets/bytes being Green compliant (i.e. in case of srTCM and trTCM, packet is CIR/CBS compliant) per UNI port, per CVLAN. This object is applicable only when ingress bandwidth is not shared across SAP ports and CVLANs.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

alaEServiceSapCvlanPortStatYellowCount		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.10.1.5
Counter for the number of packets/bytes being Yellow compliant (i.e. in case of srTCM and trTCM, packet is PIR/PBS compliant) per UNI port, per CVLAN. This object is applicable only when ingress bandwidth is not shared across SAP ports and CVLANs.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

alaEServiceSapCvlanPortStatRedCount		1.3.6.1.4.1.6486.801.1.2.1.50.1.1.1.10.1.6
Counter for the number of packets/bytes being Red compliant (i.e. in case of srTCM and trTCM, packet is neither CIR/CBS nor PIR/PBS compliant) per UNI port, per CVLAN. This object is applicable only when ingress bandwidth is not shared across SAP ports and CVLANs.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

alcatelIND1EServiceMIBCompliance		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.2.1
Compliance statement for E-Service.
Status: current	Access: read-only
MODULE-COMPLIANCE

alaEServiceSapProfileGroup		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1.1
Collection of objects for management of E-Service Sap Profiles.
Status: current	Access: read-only
OBJECT-GROUP

alaEServiceUNIProfileGroup		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1.2
Collection of objects for management of EService UNI Profiles.
Status: current	Access: read-only
OBJECT-GROUP

alaEServiceGroup		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1.3
Collection of objects for management of E-Services.
Status: current	Access: read-only
OBJECT-GROUP

alaEServiceSapGroup		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1.4
Collection of objects for management of E-Service SAPs.
Status: current	Access: read-only
OBJECT-GROUP

alaEServiceSapCvlanGroup		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1.5
Collection of objects for management of E-Service SAP CVLAN bindings.
Status: current	Access: read-only
OBJECT-GROUP

alaEServicePortGroup		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1.6
Collection of objects for management of E-Service Ports.
Status: current	Access: read-only
OBJECT-GROUP

alaEServiceSapUniGroup		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1.7
Collection of objects for management of E-Service SAP to UNI Binding.
Status: current	Access: read-only
OBJECT-GROUP

alaEServiceNniSvlanGroup		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1.8
Collection of objects for management of E-Service SVLAN to NNI Binding.
Status: current	Access: read-only
OBJECT-GROUP

alaEServiceSapCvlanPortStatGroup		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1.9
Collection of objects for srTCM and trTCM Counters.
Status: current	Access: read-only
OBJECT-GROUP

alaEServiceInfoGroup		1.3.6.1.4.1.6486.801.1.2.1.50.1.2.1.10
Collection of E-Service Global Objects.
Status: current	Access: read-only
OBJECT-GROUP