ALCATEL-IND1-INLINE-POWER-MIB
File:
ALCATEL-IND1-INLINE-POWER-MIB.mib (14618 bytes)
Imported modules
Imported symbols
Defined Types
AlaPethPsePortEntry |
|
SEQUENCE |
|
|
|
|
alaPethPsePortPowerMaximum |
INTEGER |
|
|
alaPethPsePortPowerActual |
INTEGER |
|
|
alaPethPsePortPowerStatus |
INTEGER |
|
|
alaPethPsePortPowerClass |
INTEGER |
|
AlaPethMainPseEntry |
|
SEQUENCE |
|
|
|
|
alaPethMainPseAdminStatus |
INTEGER |
|
|
alaPethMainPseMaxPower |
Integer32 |
|
|
alaPethMainPsePriorityDisconnect |
INTEGER |
|
|
alaPethMainPseCapacitorDetect |
INTEGER |
|
|
alaPethMainPsePriority |
INTEGER |
|
|
alaPethMainPseComboPort |
INTEGER |
|
AlaPethMainEntry |
|
SEQUENCE |
|
|
|
|
alaPethMainIndex |
Integer32 |
|
|
alaPethMainPowerRedundancy |
INTEGER |
|
Defined Values
alcatelIND1INLINEPOWERMIB |
1.3.6.1.4.1.6486.801.1.2.1.27.1 |
This module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
Propietary InLinePower Extensions MIB definitions
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special,
or consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2007 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE |
MODULE-IDENTITY |
|
|
|
alaPethMain |
1.3.6.1.4.1.6486.801.1.2.1.27.1.3 |
OBJECT IDENTIFIER |
|
|
|
alaPethPsePortTable |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.1 |
A table of objects that augments the standard pethPsePortTable
entry by adding the alaPethPsePortPowerMaximum object. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AlaPethPsePortEntry |
|
alaPethPsePortEntry |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.1.1 |
A set of objects that display and control the power
characteristics of a power Ethernet PSE port. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AlaPethPsePortEntry |
|
|
alaPethPsePortPowerMaximum |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.1.1.1 |
This object controls maximum amount of power per port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
3000..30000 |
|
alaPethPsePortPowerActual |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.1.1.2 |
This object contains the actual amount of power used by a port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..30000 |
|
alaPethPsePortPowerStatus |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.1.1.3 |
This object contains the power status of a port |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
powerOn(1), powerOff(2) |
|
alaPethPsePortPowerClass |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.1.1.4 |
This object controls class of poe device attached on a port.
class0 - The device can draw PD power from 0.44W to 12.95W and
current less than 5.0 mA.
class1 - The device can draw PD power from 0.44W to 3.84W and
current 10.5 mA.
class2 - The device can draw PD power from 3.84W to 6.49W and
current 12.95 mA.
class3 - The device can draw PD power from 6.49W to 12.95W and
current 28 mA.
class4 - This class is reserved for future use.
class5 - No Powered Device is connected to this POE port, or the
port is powered down. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
class0(0), class1(1), class2(2), class3(3), class4(4), class5(5) |
|
alaPethMainPseTable |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.2 |
This table augments the standard table PethMainPseTable by allowing the
admin status for a group to be set to on/off as well as
showing the values for the max power for that group. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AlaPethMainPseEntry |
|
alaPethMainPseEntry |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.2.1 |
A set of objects that display and control the Main power
of a PSE. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AlaPethMainPseEntry |
|
|
alaPethMainPseAdminStatus |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.2.1.1 |
The object is used to set the status of the main PSE to ON or OFF. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
on(1), off(2) |
|
alaPethMainPseMaxPower |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.2.1.2 |
The maximum amount of power allowed for main PSE. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Integer32 |
36..800 |
|
alaPethMainPsePriorityDisconnect |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.2.1.3 |
The object is used to set the priority disconnect of the
main PSE to Enabled or Disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaPethMainPseCapacitorDetect |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.2.1.4 |
The object is used to enable or disable the PowerDsine
Capacitor detection method. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaPethMainPsePriority |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.2.1.5 |
The object is set the power down priority for the slot |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
critical(1), high(2), low(3) |
|
alaPethMainPseComboPort |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.2.1.6 |
The object is used to set the combo port option of the
main PSE to Enable or Disable. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
alaPethGroups |
1.3.6.1.4.1.6486.801.1.2.1.27.1.2.2 |
OBJECT IDENTIFIER |
|
|
|
alaPethCompliance |
1.3.6.1.4.1.6486.801.1.2.1.27.1.2.1.1 |
Describes the requirements for conformance to the
Alcatel Power Ethernet MIB. |
Status: current |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
alaPethPseCompliance |
1.3.6.1.4.1.6486.801.1.2.1.27.1.2.1.2 |
Describes the requirements for conformance to the PSE |
Status: current |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|
alaPethPsePortGroup |
1.3.6.1.4.1.6486.801.1.2.1.27.1.2.2.1 |
The pethPsePortGroup is mandatory for systems which
implement PSE ports. |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|
alaPethMainPseGroup |
1.3.6.1.4.1.6486.801.1.2.1.27.1.2.2.2 |
Main PSE Objects. |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|
alaPethMainTable |
1.3.6.1.4.1.6486.801.1.2.1.27.1.3.1 |
A table of objects that augments the standard pethPsePortTable
entry by adding the alaPethPsePortPowerMaximum object. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AlaPethMainEntry |
|
alaPethMainEntry |
1.3.6.1.4.1.6486.801.1.2.1.27.1.3.1.1 |
A set of objects that display and control the power
characteristics of a power Ethernet PSE port. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AlaPethMainEntry |
|
|
alaPethMainIndex |
1.3.6.1.4.1.6486.801.1.2.1.27.1.3.1.1.1 |
This variable uniquely identifies the group to which
power Ethernet PSE is connected.Group means (box in the stack,
module in a rack) and the value 1 MUST be used for non-modular
devices |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Integer32 |
1..2147483647 |
|
alaPethMainPowerRedundancy |
1.3.6.1.4.1.6486.801.1.2.1.27.1.3.1.1.2 |
This object controls power supply redundancy. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
pethSourceSlot |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.3.1 |
Slot number of generating entity. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..64 |
|
pethSourcePort |
1.3.6.1.4.1.6486.801.1.2.1.27.1.1.3.2 |
Port number of generating entity. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..48 |
|
pethPwrSupplyConflict |
1.3.6.1.4.1.6486.801.1.3.2.17.0.1 |
Power supply type conflict trap. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
pethPwrSupplyNotSupported |
1.3.6.1.4.1.6486.801.1.3.2.17.0.2 |
Power supply not supported trap. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
pethTrapsGroup |
1.3.6.1.4.1.6486.801.1.2.1.27.1.2.2.3 |
Notifications for PETH MIB |
Status: current |
Access: read-only |
NOTIFICATION-GROUP |
|
|
|
alaPethTrapObjGroup |
1.3.6.1.4.1.6486.801.1.2.1.27.1.2.2.4 |
Collection of Objects used by PETH Notifications. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|