ALCATEL-IND1-PIM-MIB

File: ALCATEL-IND1-PIM-MIB.mib (27563 bytes)

Imported modules

SNMPv2-SMI INET-ADDRESS-MIB PIM-STD-MIB
SNMPv2-TC SNMPv2-CONF ALCATEL-IND1-BASE

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
IpAddress Integer32 TimeTicks
Unsigned32 Counter32 InetAddressType
InetAddress InetAddressPrefixLength pimInterfaceEntry
RowStatus TruthValue MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP routingIND1Pim

Defined Types

AlaPimdmDenseGroupEntry  
SEQUENCE    
  alaPimdmDenseGroupAddressType InetAddressType
  alaPimdmDenseGroupGrpAddress InetAddress
  alaPimdmDenseGroupGrpPrefixLength InetAddressPrefixLength
  alaPimdmDenseGroupOverrideDynamic TruthValue
  alaPimdmDenseGroupPrecedence Unsigned32
  alaPimdmDenseGroupRowStatus RowStatus

AlaPimInterfaceAugEntry  
SEQUENCE    
  alaPimInterfaceBfdStatus INTEGER

Defined Values

alcatelIND1PIMMIB 1.3.6.1.4.1.6486.801.1.2.1.10.6.1
This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): This proprietary MIB contains management information for the configuration of PIM-SM and PIM-DM global configuration parameters. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
MODULE-IDENTITY    

alcatelIND1PIMMIBObjects 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1
OBJECT IDENTIFIER    

alaPimsmGlobalConfig 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1
OBJECT IDENTIFIER    

alaPimdmGlobalConfig 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2
OBJECT IDENTIFIER    

alaPimGlobalConfig 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3
OBJECT IDENTIFIER    

alaPimsmAdminStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.1
Administratively enables/disables the PIM-SM protocol on this router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmMaxRPs 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.2
The maximum number of C-RPs allowed in the PIM-SM domain.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..100  

alaPimsmProbeTime 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.3
When NULL Registers are used, this is the time between sending a NULL Register and the Register- Suppression-Timer expiring unless it is restarted by receiving a Register-Stop.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..300  

alaPimsmOldRegisterMessageSupport 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.4
Specifies the application of the checksum function on received Register messages in the PIM-SM domain. When set to full(2), the checksum for a register message is computed for the entire packet (i.e. includes data). When set to header(1), the checksum is done only on the first 8 bytes of the packet. This variable is provided for interoperability reasons and may be required for Compatibility with older implementations of PIM-SM v2. This parameter must be set the same throughout the PIM-SM domain.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER header(1), full(2)  

alaPimsmAdminSPTConfig 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.5
Administratively enables/disables SPT Switchover upon receiving the first data packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmRPThreshold 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.6
Sets the RP threshold value (in bps) to be used in determining when to switch to native forwarding at the RP. The value of 0 disables the RP Threshold functionality.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..2147483647  

alaPimsmV6AdminStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.7
Administratively enables/disables the PIM-SM IPv6 protocol on this router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmV6SPTConfig 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.8
Administratively enables/disables PIM IPv6 SPT Switchover upon receiving the first data packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmV6RPSwitchover 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.9
Administratively enables/disables whether PIM IPv6 will attempt to switch to native forwarding at the RP upon receiving the first register-encapsulated packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmBidirStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.10
Administratively enables/disables the PIM BIDIR protocol on this router.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmBidirPeriodicInterval 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.11
This is the interval at which the DF for each RPA will periodically announce its status in a Winner message. A value of 0 indicates that periodic messages will not be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..2000  

alaPimsmBidirDFAbort 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.12
Administratively enables/disables whether the DF election will be automatically aborted if a PIM hello is received from a PIM neighbor without the bidirectional capable option. By default, the DF election will still occur among those PIM routers that support BIDIR. By enabling this option, if a BIDIR- capable router receives a PIM hello from a non-BIDIR-capable router, the DF election is aborted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmNonBidirHelloPeriod 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.13
The minimum time that must elapse between alaPimNonBidirHello notifications originated by this router. The default value of 65535 represents an 'infinite' time, in which case, no alaPimNonBidirHello notifications are ever sent. The non-zero minimum allowed value provides resilience against propagation of denial-of-service attacks from the control plane to the network management plane.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 10..65535  

alaPimsmNonBidirHelloMsgsRcvd 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.14
The number of PIM Hello messages that have been received by a BIDIR-capable device that do not have the Bidirectional Capable option. This counter is incremented if BIDIR mode is enabled on this router and a PIM Hello message is received from a PIM neighbor that does not include the Bidirectional Capable option. By default, the reception of these messages will not effect the BIDIR DF election. The alaPimsmBidirDFAbort object may be used to change the default behavior and have the DF election aborted whenever a BIDIR-capable router receives a PIM hello from a non-BIDIR-capable router.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaPimsmNonBidirHelloAddressType 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.15
The address type stored in alaPimsmNonBidirHelloOrigin. If no Non Bidir Hello messages have been received, this object is set to unknown(0).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

alaPimsmNonBidirHelloOrigin 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.16
The source address of the last Non Bidir Hello message received by this device.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4|8|16|20)  

alaPimsmV6BidirStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.17
Administratively enables/disables the PIM IPv6 BIDIR protocol on this router.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimdmAdminStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.1
Administratively enables/disables the PIM-DM protocol on this router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimdmStateRefreshTimeToLive 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.2
The TTL to be used by this router's originated State Refresh messages if the data packet's TTL is not recorded.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

alaPimdmStateRefreshLimitInterval 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.3
This router will not forward successive State Refresh messages received at less than this interval.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

alaPimdmV6AdminStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.4
Administratively enables/disables the PIM-DM IPv6 protocol on this router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimdmDenseGroupTable 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5
This table is used to manage configuration of dense groups. If the group prefixes configured for two or more rows in this table overlap, the row with the greatest value of alaPimdmDenseGroupGrpPrefixLength is used for the overlapping range.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlaPimdmDenseGroupEntry

alaPimdmDenseGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1
An entry (conceptual row) in the alaPimdmDenseGroupTable. This entry is preserved on agent restart.
Status: current Access: not-accessible
OBJECT-TYPE    
  AlaPimdmDenseGroupEntry  

alaPimdmDenseGroupAddressType 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.1
The address type of this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

alaPimdmDenseGroupGrpAddress 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.2
The multicast group address that, when combined with alaPimdmDenseGroupGrpPrefixLength, gives the group prefix for this entry. The InetAddressType is given by the alaPimdmDenseGroupAddressType object. This address object is only significant up to alaPimdmDenseGroupGrpPrefixLength bits. The remainder of the address bits are zero. This is especially important for this index field, which is part of the index of this entry. Any non-zero bits would signify an entirely different entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4|8|16|20)  

alaPimdmDenseGroupGrpPrefixLength 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.3
The multicast group prefix length that, when combined with alaPimdmDenseGroupGrpAddress, gives the group prefix for this entry. The InetAddressType is given by the alaPimdmDenseGroupAddressType object. If alaPimdmDenseGroupAddressType is 'ipv4' or 'ipv4z', this object must be in the range 4..32. If alaPimdmDenseGroupGrpAddressType is 'ipv6' or 'ipv6z', this object must be in the range 8..128.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressPrefixLength 4..128  

alaPimdmDenseGroupOverrideDynamic 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.4
Whether this dense group configuration will override other group mappings in this group prefix. If this object is TRUE, then it will override: - RP information learned dynamically for groups in this group prefix. - RP information configured in alaPimdmDenseGroupTable with alaPimdmDenseGroupOverrideDynamic set to FALSE. See pimGroupMappingTable for details.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

alaPimdmDenseGroupPrecedence 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.5
The value for pimGroupMappingPrecedence to be used for this static RP configuration. This allows fine control over which configuration is overridden by this static configuration. If alaPimdmDenseGroupOverrideDynamic is set to TRUE, all dynamic RP configuration is overridden by this static configuration, whatever the value of this object. The absolute values of this object have a significance only on the local router and do not need to be coordinated with other routers. A setting of this object may have different effects when applied to other routers. Do not use this object unless fine control of static RP behavior on the local router is required.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

alaPimdmDenseGroupRowStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.6
The status of this row, by which rows in this table can be created and destroyed. All writeable objects in this entry can be modified when the status of this entry is active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaPimBfdStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.1
Administratively enables/disables PIM with the BFD protocol on this router.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimBfdAllInterfaceStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.2
Administratively enables/disables BFD for all PIM interfaces on this router.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimMoFRRStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.3
Administratively enables/disables MoFRR (Multicast only Fast Re-Route) on this router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimMoFRRAllRouteStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.4
By default, MoFRR is only applied to multicast routes that have local clients. Enabling alaPimMoFRRAllRouteStatus will enable MoFRR on all routes whether there are local clients or not. alaPimMoFRRStatus must be enabled for this to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimInterfaceAugTable 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5
Expansion for pimInterfaceTable
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlaPimInterfaceAugEntry

alaPimInterfaceAugEntry 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5.1
An entry of alaPimInterfaceAugTable
Status: current Access: not-accessible
OBJECT-TYPE    
  AlaPimInterfaceAugEntry  

alaPimInterfaceBfdStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5.1.1
Enables/Disables BFD for particular interfaces of PIM.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimMbrAllSourcesStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.6
Administratively enables/disables PIM to notify DVMRP about the routes to all multicast sources learned instead of just the directly connected subnets so that these routes can be advertised in the DVMRP domain via standard DVMRP mechanisms. This object is only applicable if the router is operating as a Multicast Border Router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimMbrOperStatus 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.7
Whether MBR is currently enabled/disabled for PIM.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimNotifications 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.0
OBJECT IDENTIFIER    

alaPimNonBidirHello 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.0.1
An alaPimNonBidirHello notification signifies that a bidir-capable router has received a PIM hello from a non-bidir-capable router. This notification is generated whenever the counter alaPimsmNonBidirHelloMsgsRcvd is incremented, subject to the rate limit specified by alaPimsmNonBidirHelloNotificationPeriod.
Status: current Access: read-only
NOTIFICATION-TYPE    

alcatelIND1PIMMIBConformance 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2
OBJECT IDENTIFIER    

alcatelIND1PIMMIBCompliances 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.1
OBJECT IDENTIFIER    

alcatelIND1PIMMIBGroups 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2
OBJECT IDENTIFIER    

alaPimsmCompliance 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.1.1
The compliance statement for routers running PIM Sparse Mode and implementing the ALCATEL-IND1-PIM MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

alaPimdmCompliance 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.1.2
The compliance statement for routers running PIM Dense Mode and implementing the ALCATEL-IND1-PIM MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

alaPimsmConfigMIBGroup 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2.1
A collection of objects to support management of global configuration parameters of PIM Sparse Mode routers.
Status: current Access: read-only
OBJECT-GROUP    

alaPimdmConfigMIBGroup 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2.2
A collection of objects to support management of global configuration parameters of PIM Dense Mode routers.
Status: current Access: read-only
OBJECT-GROUP    

alaPimConfigMIBGroup 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2.3
A collection of objects to support management of global configuration parameters of PIM routers.
Status: current Access: read-only
OBJECT-GROUP    

alaPimOptionalGroup 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2.4
PIM objects to stop the tools from complaining
Status: current Access: read-only
OBJECT-GROUP    

alaPimNotificationGroup 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2.5
PIM Notification objects
Status: current Access: read-only
NOTIFICATION-GROUP