APEX-MIB

File: APEX-MIB.mib (939819 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC BCS-IDENT-MIB
BCS-TRAPS-MIB

Imported symbols

MODULE-IDENTITY IpAddress TimeTicks
OBJECT-TYPE NOTIFICATION-TYPE Counter32
Unsigned32 Integer32 DisplayString
giproducts trapIdentifier trapSequenceId
trapNetworkElemModelNumber trapNetworkElemSerialNum trapPerceivedSeverity
trapNetworkElemOperState trapNetworkElemAlarmStatus trapNetworkElemAdminState
trapNetworkElemAvailStatus trapText trapNETrapLastTrapTimeStamp
trapChangedObjectId trapAdditionalInfoInteger1 trapAdditionalInfoInteger2
trapAdditionalInfoInteger3 trapChangedValueDisplayString trapChangedValueOID
trapChangedValueIpAddress trapChangedValueInteger

Defined Types

EnableDisableTYPE  
INTEGER disabled(1), enabled(2)    

ActiveTYPE  
INTEGER notApplicable(0), notActive(1), active(2)    

ApplyDataToDeviceTYPE  
INTEGER applyNotInProgress(1), apply(2), applyNotInProgressValidData(3), applyNotInProgressInvalidData(4)    

ResetStatisticsTYPE  
INTEGER resetNotInProgress(1), reset(2)    

ClearAlarmTYPE  
INTEGER clearAlarmNotInProgress(1), clearAlarm(2)    

RateComparisonTYPE  
INTEGER dataRate(1), transportStreamRate(2)    

InputTsStateTYPE  
INTEGER closed(0), openedInUse(1), openedBackup(2), openedTransToBackup(3), openedTransToInUse(4)    

EthernetInterfaceTYPE  
INTEGER enet1(1), enet2(2)    

ApexPsStatusEntry  
SEQUENCE    
  apexPsStatusPsNum Integer32
  apexPsStatusInstalled INTEGER
  apexPsStatusOutputVoltage Integer32
  apexPsStatusOutputCurrent Integer32
  apexPsStatusFanSpeed Unsigned32
  apexPsStatusFanStatus INTEGER
  apexPsStatusTemperatureStatus INTEGER
  apexPsStatusInputPowerStatus INTEGER
  apexPsStatusOutputPowerStatus INTEGER
  apexPsStatusErrorStatus INTEGER
  apexPsStatusFaultCondition INTEGER
  apexPsStatusDiagnosticData1 Integer32
  apexPsStatusDiagnosticData2 Integer32
  apexPsStatusCommError INTEGER

ApexPsStatusVersionsEntry  
SEQUENCE    
  apexPsStatusVersionsPsNum Integer32
  apexPsStatusVersionsModel DisplayString
  apexPsStatusVersionsSerialNumber DisplayString

ApexFastEnetRoutingEntry  
SEQUENCE    
  apexFastEnetRoutingIndex Integer32
  apexFastEnetRoutingDestinIp IpAddress
  apexFastEnetRoutingGatewayIp IpAddress
  apexFastEnetRoutingSubnetMask IpAddress

ApexFastEnetInsertRateEntry  
SEQUENCE    
  apexFastEnetInsertRateOutputTsNum Integer32
  apexFastEnetInsertRate Integer32

ApexFastEnetStatusPacketsEntry  
SEQUENCE    
  apexFastEnetPacketsPortNum Integer32
  apexFastEnetPacketsNumPkts Unsigned32
  apexFastEnetPacketsTotPkts Unsigned32
  apexFastEnetPacketsNumDiscarded Unsigned32
  apexFastEnetPacketsTotDiscarded Unsigned32

ApexFastEnetInsertPacketsEntry  
SEQUENCE    
  apexFastEnetInsPacketsOutputTsNum Integer32
  apexFastEnetInsPacketsNumPkts Unsigned32
  apexFastEnetInsPacketsTotPkts Unsigned32
  apexFastEnetInsPacketsNumDiscarded Unsigned32
  apexFastEnetInsPacketsTotDiscarded Unsigned32

ApexGbeConfigEntry  
SEQUENCE    
  apexGbeConfigInterfaceNum Integer32
  apexGbeConfigEnable EnableDisableTYPE
  apexGbeConfigIpAddr IpAddress
  apexGbeConfigIpSubnetMask IpAddress
  apexGbeConfigAutoNegotiate EnableDisableTYPE

ApexGbeConfigFrameBufferEntry  
SEQUENCE    
  apexGbeConfigFrameBufferProcessorNum Integer32
  apexGbeConfigFrameBufferMaxInDataRate Unsigned32
  apexGbeConfigFrameBufferAlarmThreshold Integer32

ApexGbeConfigInputDataTsEntry  
SEQUENCE    
  apexGbeConfigInputDataTsIndex Integer32
  apexGbeConfigInputDataTsEnable EnableDisableTYPE
  apexGbeConfigInputDataTsInterface Integer32
  apexGbeConfigInputDataTsUdp Integer32
  apexGbeConfigInputDataTsMulticastIp IpAddress
  apexGbeConfigInputDataTsSourceIp IpAddress

ApexGbeConfigInputDataTsApplyEntry  
SEQUENCE    
  apexGbeConfigInputDataTsApplyIndex Integer32
  apexGbeConfigInputDataTsApplyChange ApplyDataToDeviceTYPE

ApexGbeConfigInterfaceRedundancyEntry  
SEQUENCE    
  apexGbeConfIfRedundIndex Integer32
  apexGbeConfIfRedundEnable EnableDisableTYPE
  apexGbeConfIfRedundForceFailover INTEGER
  apexGbeConfIfRedundSuspendFailover EnableDisableTYPE

ApexGbeConfigInterfaceRedundancyApplyEntry  
SEQUENCE    
  apexGbeConfIfRedundApplyIndex Integer32
  apexGbeConfIfRedundApplyChange ApplyDataToDeviceTYPE

ApexGbeStatusEntry  
SEQUENCE    
  apexGbeStatusGbeInterfaceNum Integer32
  apexGbeStatusMacAddr DisplayString
  apexGbeStatusLinkActive ActiveTYPE
  apexGbeStatusIgmpVersion INTEGER
  apexGbeStatusLossOfPhysicalInput INTEGER

ApexGbeInputTsAssignedEntry  
SEQUENCE    
  apexGbeInputTsAssignedGbeInterfaceNum Integer32
  apexGbeInputTsAssignedCount Counter32

ApexGbeOpenInputUdpPortEntry  
SEQUENCE    
  apexGbeOpenInputUdpPortGbeInterfaceNum Integer32
  apexGbeOpenInputUdpPortCount Counter32

ApexGbeStatusRoutedPacketEntry  
SEQUENCE    
  apexGbeStatusRoutedPacketOutputTsNum Integer32
  apexGbeStatusTotRoutedPackets Counter32
  apexGbeStatusNumRoutedPackets Counter32

ApexGbeStatusFrameCounterEntry  
SEQUENCE    
  apexGbeFrameCounterGbeInterfaceNum Integer32
  apexGbeFrameCounterReset ResetStatisticsTYPE
  apexGbeTotalRxSinglecastFrames Counter32
  apexGbeTotalRxMulticastFrames Counter32
  apexGbeTotalRxBroadcastFrames Counter32
  apexGbeTotalRxErrorFrames Counter32
  apexGbeTotalRxFrames Counter32
  apexGbeRxSinglecastFrames Counter32
  apexGbeRxMulticastFrames Counter32
  apexGbeRxBroadcastFrames Counter32
  apexGbeRxErrorFrames Counter32
  apexGbeRxFrames Counter32
  apexGbeTotalTxGoodFrames Counter32
  apexGbeTotalTxErrorFrames Counter32
  apexGbeTxGoodFrames Counter32
  apexGbeTxErrorFrames Counter32
  apexGbeRxDocsisFrames Counter32
  apexGbeRxMpegDocsisFrames Counter32
  apexGbeTotalRxDocsisFrames Counter32
  apexGbeIpFragmentedPkts Counter32
  apexGbeTotalIpFragmentedPkts Counter32

ApexGbeFrameBufferStatsEntry  
SEQUENCE    
  apexGbeFrameBufferProcessorNum Integer32
  apexGbeFrameBufferResetLevelLimit Integer32
  apexGbeFrameBufferCurrMsLevel Integer32
  apexGbeFrameBufferCurrPercentFull Integer32
  apexGbeFrameBufferUnderflowLevel Integer32
  apexGbeFrameBufferOverflowLevel Integer32
  apexGbeFrameBufferAlarmStatus INTEGER

ApexGbeFrameBufferHourlyEntry  
SEQUENCE    
  apexGbeFrameBufferHourlyProcessorNum Integer32
  apexGbeFrameBufferHourlyIndex Integer32
  apexGbeFrameBufferHourlyInInterface Integer32
  apexGbeFrameBufferHourlyInUdp Integer32
  apexGbeFrameBufferHourlyInMulticastIp IpAddress
  apexGbeFrameBufferHourlyInSourceIp IpAddress
  apexGbeFrameBufferHourlyMaxMsLevel Integer32
  apexGbeFrameBufferHourlyMaxPercentFull Integer32
  apexGbeFrameBufferHourlyGpsTime Integer32
  apexGbeFrameBufferHourlyOverflows Integer32
  apexGbeFrameBufferHourlyResets Integer32

ApexGbeStatusInputTsEntry  
SEQUENCE    
  apexGbeStatInTsInputTsNum Integer32
  apexGbeStatInTsSamplingPeriod Integer32
  apexGbeStatInTsPriCurDataCount Counter32
  apexGbeStatInTsPriAvgDataCount Counter32
  apexGbeStatInTsPriMinDataCount Counter32
  apexGbeStatInTsPriPeakDataCount Counter32
  apexGbeStatInTsPriCurStreamCount Counter32
  apexGbeStatInTsPriAvgStreamCount Counter32
  apexGbeStatInTsPriMinStreamCount Counter32
  apexGbeStatInTsPriPeakStreamCount Counter32
  apexGbeStatInTsSecCurDataCount Counter32
  apexGbeStatInTsSecAvgDataCount Counter32
  apexGbeStatInTsSecMinDataCount Counter32
  apexGbeStatInTsSecPeakDataCount Counter32
  apexGbeStatInTsSecCurStreamCount Counter32
  apexGbeStatInTsSecAvgStreamCount Counter32
  apexGbeStatInTsSecMinStreamCount Counter32
  apexGbeStatInTsSecPeakStreamCount Counter32

ApexGbeStatusInputTsErrorEntry  
SEQUENCE    
  apexGbeStatInTsErrorInputTsNum Integer32
  apexGbeStatInTsPriErrorSummary INTEGER
  apexGbeStatInTsPriLowBitRateError INTEGER
  apexGbeStatInTsPriHighBitRateError INTEGER
  apexGbeStatInTsMptsRedundPriError INTEGER
  apexGbeStatInTsMptsRedundFailError INTEGER
  apexGbeStatInTsSecErrorSummary INTEGER
  apexGbeStatInTsSecLowBitRateError INTEGER
  apexGbeStatInTsSecHighBitRateError INTEGER
  apexGbeStatInTsPriLossInputError INTEGER
  apexGbeStatInTsSecLossInputError INTEGER

ApexGbeStatusInterfaceRedundEntry  
SEQUENCE    
  apexGbeStatusInterfaceRedundIndex Integer32
  apexGbeStatusInterfaceRedundActiveIf Integer32
  apexGbeStatusInterfaceRedundInvalidApplyText DisplayString
  apexGbeStatusInterfaceRedundFaultCondition INTEGER

ApexGbeSfpStatusEntry  
SEQUENCE    
  apexGbeSfpStatusGbeIfNum Integer32
  apexGbeSfpStatusVendorId DisplayString
  apexGbeSfpStatusDiagInfo DisplayString

ApexQamConfigApplyEntry  
SEQUENCE    
  apexQamConfigApplyRfPortNum Integer32
  apexQamConfigApplyChange ApplyDataToDeviceTYPE

ApexQamRfConfigEntry  
SEQUENCE    
  apexQamRfConfigRfPortNum Integer32
  apexQamRfConfigNumChannelsEnabled Integer32
  apexQamRfConfigModulationMode INTEGER
  apexQamRfConfigSymbolRate Integer32
  apexQamRfConfigSpectrumInvert INTEGER
  apexQamRfConfigTuningMode INTEGER
  apexQamRfConfigEiaFrequencyPlan INTEGER
  apexQamRfConfigEiaChanNumChannelA Integer32
  apexQamRfConfigRfCenterFreqChannelA Integer32
  apexQamRfConfigRfChanSpacing Integer32
  apexQamRfConfigRfLevelAttenuation Integer32
  apexQamRfConfigRfLevelLowThreshold Integer32
  apexQamRfConfigRfLevelHighThreshold Integer32
  apexQamRfConfigMute INTEGER
  apexQamRfConfigInterleaverDepth1 INTEGER
  apexQamRfConfigInterleaverDepth2 INTEGER

ApexQamChannelConfigEntry  
SEQUENCE    
  apexQamChanConfigChannelNum Integer32
  apexQamChanConfigInterleaverSelect INTEGER
  apexQamChanConfigTestMode INTEGER

ApexQamChannelConfigApplyEntry  
SEQUENCE    
  apexQamChannelConfigApplyChannelNum Integer32
  apexQamChannelConfigApplyChange ApplyDataToDeviceTYPE

ApexQamModuleStatusEntry  
SEQUENCE    
  apexQamModuleStatQamModuleNum Integer32
  apexQamModuleStatInstalled INTEGER
  apexQamModuleStatFanSpeed Unsigned32
  apexQamModuleStatFanFault INTEGER
  apexQamModuleStatTemperature Integer32
  apexQamModuleStatTemperatureFault INTEGER
  apexQamModuleStatError INTEGER
  apexQamModuleStatFaultCondition INTEGER
  apexQamModuleStatFaultSumm INTEGER
  apexQamModuleStatPowerFault INTEGER
  apexQamModuleStatBoardTemperature Integer32
  apexQamModuleStatBoardTemperatureFault INTEGER
  apexQamModuleStat5VdcSupply Integer32
  apexQamModuleStat5VdcFault INTEGER
  apexQamModuleStat3dot3VdcSupply Integer32
  apexQamModuleStat3dot3VdcFault INTEGER
  apexQamModuleStatCommError INTEGER
  apexQamModuleStatCodeInitError INTEGER

ApexQamModuleSerialNumEntry  
SEQUENCE    
  apexQamModuleSerialNumQamModuleNum Integer32
  apexQamModuleSerialNumber DisplayString

ApexQamQrmRevisionEntry  
SEQUENCE    
  apexQamQrmRevRfPortNum Integer32
  apexQamQrmRevBoardId DisplayString
  apexQamQrmRevAppFw DisplayString
  apexQamQrmRevBootLoaderFw DisplayString
  apexQamQrmRevFpga DisplayString
  apexQamQrmRevHw DisplayString
  apexQamQrmRevSerialNumber DisplayString
  apexQamQrmRevFpga2 DisplayString

ApexQamRfPortStatusEntry  
SEQUENCE    
  apexQamRfPortStatRfPortNum Integer32
  apexQamRfPortStatInfoRate Unsigned32
  apexQamRfPortStatNumChannelsActive Integer32
  apexQamRfPortStatOutputLevel Integer32
  apexQamRfPortStatOutputLevelFault INTEGER
  apexQamRfPortStatTemperature Integer32
  apexQamRfPortStatTemperatureFault INTEGER
  apexQamRfPortStat5VdcSupply Integer32
  apexQamRfPortStat5VdcFault INTEGER
  apexQamRfPortStat3dot3VdcSupply Integer32
  apexQamRfPortStat3dot3VdcFault INTEGER
  apexQamRfPortStatFreqPllLock INTEGER
  apexQamRfPortStatRefClockPresent INTEGER
  apexQamRfPortStatRefClockLock INTEGER
  apexQamRfPortStatDataClockPresent INTEGER
  apexQamRfPortStatDataSyncFault INTEGER
  apexQamRfPortStatCommError INTEGER
  apexQamRfPortStatError INTEGER
  apexQamRfPortStatFaultCondition INTEGER
  apexQamRfPortStatChanFaultSumm INTEGER
  apexQamRfPortStatCodeInitError INTEGER

ApexQamChannelStatusEntry  
SEQUENCE    
  apexQamChanStatChannelNum Integer32
  apexQamChanStatActive ActiveTYPE
  apexQamChanStatRfFreq Integer32
  apexQamChanStatEiaChanNum Integer32
  apexQamChanStatDataPresent INTEGER
  apexQamChanStatError INTEGER
  apexQamChanStatFaultCondition INTEGER

ApexQamRfPortMuteStatusEntry  
SEQUENCE    
  apexQamRfPortMuteStatusRfPortNum Integer32
  apexQamRfPortMuteStatus INTEGER

ApexQamQrmRevisionStatusEntry  
SEQUENCE    
  apexQamQrmRevStatQrmNum Integer32
  apexQamQrmRevStatBoardId INTEGER
  apexQamQrmRevStatAppFw INTEGER
  apexQamQrmRevStatBootLoaderFw INTEGER
  apexQamQrmRevStatFpga INTEGER
  apexQamQrmRevStatHw INTEGER
  apexQamQrmRevStatQrmSupported INTEGER
  apexQamQrmRevStatFpga2 INTEGER

ApexQamRfPortChannelInfoEntry  
SEQUENCE    
  apexQamRfPortChannelInfoRfPortNum Integer32
  apexQamRfPortChannelInfoChanA Integer32
  apexQamRfPortChannelInfoChanCount Integer32

ApexQamChannelIdEntry  
SEQUENCE    
  apexQamChannelIdChannelNum Integer32
  apexQamChannelIdSlotNum Integer32
  apexQamChannelIdRfPortNum Integer32
  apexQamChannelIdModuleRfPortNum Integer32
  apexQamChannelIdChannelLetter DisplayString
  apexQamChannelIdChannelDescription DisplayString

ApexQrmDownloadConfigEntry  
SEQUENCE    
  apexQrmDownloadConfigQrmNum Integer32
  apexQrmDownloadConfigRequest INTEGER

ApexQrmDownloadStatusEntry  
SEQUENCE    
  apexQrmDownloadStatusRfPortNum Integer32
  apexQrmDownloadStatusDescription DisplayString
  apexQrmDownloadProgress Integer32
  apexQrmDownloadSupported INTEGER
  apexQrmDownloadRequired INTEGER
  apexQrmDownloadFileSet INTEGER

ApexQrmFileRevisionEntry  
SEQUENCE    
  apexQrmFileRevFileSetNum Integer32
  apexQrmFileRevFirmware DisplayString
  apexQrmFileRevCalibration DisplayString
  apexQrmFileRevFpga DisplayString
  apexQrmFileRevFpga2 DisplayString
  apexQrmFileRevDateTime DisplayString

ApexSesContConfEntry  
SEQUENCE    
  apexSesContConfOutputTsNum Integer32
  apexSesContConfGbePrimaryInterface Integer32
  apexSesContConfGbeSecondaryInterface Integer32

ApexRpcRfPortEntry  
SEQUENCE    
  apexRpcRfPortNum Integer32
  apexRpcRfPortName DisplayString
  apexRpcRfPortServiceGroup Unsigned32

ApexRpcRfChannelEntry  
SEQUENCE    
  apexRpcRfChannelNum Integer32
  apexRpcRfChannelName DisplayString

ApexRpcSessionStatEntry  
SEQUENCE    
  apexRpcSessionStatIndex Integer32
  apexRpcSessionStatInputTsIndex Integer32
  apexRpcSessionStatInputProgramNum Integer32
  apexRpcSessionStatSourceIpAddr3 IpAddress
  apexRpcSessionStatOutputQamChannel Integer32
  apexRpcSessionStatOutputProgramNum Integer32
  apexRpcSessionStatProgramBandwidth Integer32
  apexRpcSessionStatSessionType INTEGER
  apexRpcSessionStatSessionIdWord1 Unsigned32
  apexRpcSessionStatSessionIdWord2 Unsigned32
  apexRpcSessionStatSessionIdWord3 Unsigned32
  apexRpcSessionStatManagerIpAddr IpAddress

ApexRpcQamStatEntry  
SEQUENCE    
  apexRpcQamStatQamChannelNum Integer32
  apexRpcQamStatNumSdvSessions Integer32
  apexRpcQamStatNumVodBcSessions Integer32
  apexRpcQamStatSdvGroupBandwidth Unsigned32

ApexRtspConfControllerApplyEntry  
SEQUENCE    
  apexRtspConfControllerApplyNum Integer32
  apexRtspConfControllerApplyChange ApplyDataToDeviceTYPE

ApexRtspConfControllerEntry  
SEQUENCE    
  apexRtspConfControllerNum Integer32
  apexRtspConfControllerIp IpAddress
  apexRtspConfControllerPort Integer32
  apexRtspConfControllerHoldTime Integer32
  apexRtspConfControllerBandwidthDelta Integer32

ApexRtspConfControlNamesEntry  
SEQUENCE    
  apexRtspConfControlNamesNum Integer32
  apexRtspConfControlNamesStreamingZone DisplayString
  apexRtspConfControlNamesDeviceName DisplayString

ApexRtspConfQamChannelApplyEntry  
SEQUENCE    
  apexRtspConfQamChannelApplyNum Integer32
  apexRtspConfQamChannelApplyChange ApplyDataToDeviceTYPE

ApexRtspConfQamChannelEntry  
SEQUENCE    
  apexRtspConfQamChannelNum Integer32
  apexRtspConfQamChannelGroupName DisplayString

ApexRtspConfGbeEdgeGroupEntry  
SEQUENCE    
  apexRtspConfGbeEdgeGroupNum Integer32
  apexRtspConfGbeEdgeGroupName DisplayString

ApexRtspConfMhaEntry  
SEQUENCE    
  apexRtspConfMhaNum Integer32
  apexRtspConfMhaAddressDomain Integer32
  apexRtspConfMhaPort Integer32

ApexRtspSessionStatEntry  
SEQUENCE    
  apexRtspSessionStatIndex Integer32
  apexRtspSessionStatInputTsIndex Integer32
  apexRtspSessionStatInputProgramNum Integer32
  apexRtspSessionStatOutputQamChannel Integer32
  apexRtspSessionStatOutputProgramNum Integer32
  apexRtspSessionStatProgramBandwidth Integer32
  apexRtspSessionStatManagerIpAddr IpAddress

ApexRtspSessionIdEntry  
SEQUENCE    
  apexRtspSessionIdIndex Integer32
  apexRtspSessionId DisplayString

ApexRtspQamStatEntry  
SEQUENCE    
  apexRtspQamStatQamChannelNum Integer32
  apexRtspQamStatNumSessions Integer32
  apexRtspQamStatAllocatedBandwidth Unsigned32

ApexRtspStatControllerEntry  
SEQUENCE    
  apexRtspStatControllerNum Integer32
  apexRtspStatControllerDiscovery INTEGER
  apexRtspStatControllerConnection INTEGER
  apexRtspStatControllerCommFault INTEGER

ApexRtspStatQamChannelEntry  
SEQUENCE    
  apexRtspStatQamChannelNum Integer32
  apexRtspStatQamChannelName DisplayString

ApexRtspStatQamMptsModeEntry  
SEQUENCE    
  apexRtspStatQamMptsModeQamChannelNum Integer32
  apexRtspStatQamMptsModeQamChannelMode INTEGER

ApexManualRouteApplyEntry  
SEQUENCE    
  apexManualRouteApplyIndex Integer32
  apexManualRouteApplyChange ApplyDataToDeviceTYPE

ApexManualRouteEntry  
SEQUENCE    
  apexManualRouteIndex Integer32
  apexManualRouteEnable EnableDisableTYPE
  apexManualRouteInputType INTEGER
  apexManualRouteInputInterface Integer32
  apexManualRouteInputUdp Integer32
  apexManualRouteInputMulticastIp IpAddress
  apexManualRouteInputSourceIp IpAddress
  apexManualRouteInputProgNum Integer32
  apexManualRouteInputPreEncryptCheck EnableDisableTYPE
  apexManualRouteOutputTsNum Integer32
  apexManualRouteOutputProgNum Integer32
  apexManualRouteOutputEncryptMode INTEGER
  apexManualRouteOutputCopyProtectSource INTEGER
  apexManualRouteSourceId Integer32
  apexManualRouteProviderId Integer32

ApexManRtePassThroughApplyEntry  
SEQUENCE    
  apexManRtePassThroughApplyOutputTsNum Integer32
  apexManRtePassThroughApplyChange ApplyDataToDeviceTYPE

ApexManRtePassThroughEntry  
SEQUENCE    
  apexManRtePassThroughOutputTsNum Integer32
  apexManRtePassThroughEnable EnableDisableTYPE
  apexManRtePassThroughInputType INTEGER
  apexManRtePassThroughInputInterface Integer32
  apexManRtePassThroughInputUdp Integer32
  apexManRtePassThroughInputMulticastIp IpAddress
  apexManRtePassThroughInputSourceIp IpAddress

ApexManRteGbeInRedApplyEntry  
SEQUENCE    
  apexManRteGbeInRedApplyIndex Integer32
  apexManRteGbeInRedApplyChange ApplyDataToDeviceTYPE

ApexManRteGbeInRedEntry  
SEQUENCE    
  apexManRteGbeInRedIndex Integer32
  apexManRteGbeInRedPriInterface Integer32
  apexManRteGbeInRedPriUdp Integer32
  apexManRteGbeInRedPriMulticastIp IpAddress
  apexManRteGbeInRedPriSourceIp IpAddress
  apexManRteGbeInRedPriLowAlarmBitRate Integer32
  apexManRteGbeInRedPriHighAlarmBitRate Integer32
  apexManRteGbeInRedRateCompareType RateComparisonTYPE
  apexManRteGbeInRedEnable EnableDisableTYPE
  apexManRteGbeInRedThreshold Integer32
  apexManRteGbeInRedSuspend INTEGER
  apexManRteGbeInRedSecInterface Integer32
  apexManRteGbeInRedSecUdp Integer32
  apexManRteGbeInRedSecMulticastIp IpAddress
  apexManRteGbeInRedSecSourceIp IpAddress
  apexManRteGbeInRedSecLowAlarmBitRate Integer32
  apexManRteGbeInRedSecHighAlarmBitRate Integer32
  apexManRteGbeInRedSecRedundMcJoin INTEGER

ApexManRteGbeInRedForceSwitchEntry  
SEQUENCE    
  apexManRteGbeInRedForceSwitchIndex Integer32
  apexManRteGbeInRedForceSwitch INTEGER

ApexManRteGbeInRedStatusMapEntry  
SEQUENCE    
  apexManRteGbeInRedStatusMapIndex Integer32
  apexManRteGbeInRedStatusMapInputTsStatRow Integer32

ApexPidMapApplyEntry  
SEQUENCE    
  apexPidMapApplyIndex Integer32
  apexPidMapApplyChange ApplyDataToDeviceTYPE

ApexPidMapEntry  
SEQUENCE    
  apexPidMapIndex Integer32
  apexPidMapEnable EnableDisableTYPE
  apexPidMapInputType INTEGER
  apexPidMapInputInterface Integer32
  apexPidMapInputUdp Integer32
  apexPidMapInputMulticastIp IpAddress
  apexPidMapInputSourceIp IpAddress
  apexPidMapInputPid Integer32
  apexPidMapOutputTsNum Integer32
  apexPidMapOutputPid Integer32

ApexInsertPacketStatisticsEntry  
SEQUENCE    
  apexInsertPacketStatOutputTsNum Integer32
  apexInsertPacketStatTotPkts Integer32
  apexInsertPacketStatNumPkts Integer32

ApexInputTsStatEntry  
SEQUENCE    
  apexInputTsStatIndex Integer32
  apexInputTsStatStreamInUse INTEGER
  apexInputTsStatInputType INTEGER
  apexInputTsStatRoutingType INTEGER
  apexInputTsStatPriState InputTsStateTYPE
  apexInputTsStatPriInputInterface Integer32
  apexInputTsStatPriInputUdp Integer32
  apexInputTsStatPriInputMulticastIp IpAddress
  apexInputTsStatPriInputSourceIp IpAddress
  apexInputTsStatSecState InputTsStateTYPE
  apexInputTsStatSecInputInterface Integer32
  apexInputTsStatSecInputUdp Integer32
  apexInputTsStatSecInputMulticastIp IpAddress
  apexInputTsStatSecInputSourceIp IpAddress
  apexInputTsStatRateCompareType RateComparisonTYPE

ApexOutputTsUtilizationMonitorEntry  
SEQUENCE    
  apexOutputTsUtilMonOutputTsNum Integer32
  apexOutputTsUtilMonResetTotDropPacket ResetStatisticsTYPE

ApexOutputTsConfApplyEntry  
SEQUENCE    
  apexOutputTsConfApplyIndex Integer32
  apexOutputTsConfApplyChange ApplyDataToDeviceTYPE

ApexOutputTsConfigEntry  
SEQUENCE    
  apexOutputTsConfOutputTsNum Integer32
  apexOutputTsConfPidRemappingMode INTEGER
  apexOutputTsConfOperatingMode INTEGER
  apexOutputTsConfOutPatTsId Integer32
  apexOutputTsConfPsipEnable EnableDisableTYPE
  apexOutputTsConfEncryptionType INTEGER
  apexOutputTsConfSimulcryptMode INTEGER
  apexOutputTsConfPcrLess EnableDisableTYPE

ApexOutputTsUtilizationEntry  
SEQUENCE    
  apexOutputTsUtilizOutpuTsNum Integer32
  apexOutputTsUtilizDataFlag INTEGER
  apexOutputTsUtilizNumSamples Unsigned32
  apexOutputTsUtilizThreshold INTEGER
  apexOutputTsUtilizTime Unsigned32
  apexOutputTsUtilizCurPercent Integer32
  apexOutputTsUtilizAvgPercent Integer32
  apexOutputTsUtilizMinPercent Integer32
  apexOutputTsUtilizPeakPercent Integer32
  apexOutputTsUtilizCurRate Unsigned32
  apexOutputTsUtilizAvgRate Unsigned32
  apexOutputTsUtilizMinRate Unsigned32
  apexOutputTsUtilizPeakRate Unsigned32
  apexOutputTsUtilizOverflow INTEGER
  apexOutputTsUtilizCurDropPackets Unsigned32
  apexOutputTsUtilizPeakDropPackets Unsigned32
  apexOutputTsUtilizRollingDropPackets Unsigned32
  apexOutputTsUtilizTotalDropPackets Unsigned32
  apexOutputTsUtilizThresholdAlarm INTEGER
  apexOutputTsUtilizOverflowAlarm INTEGER

ApexOutputTsStatusEntry  
SEQUENCE    
  apexOutputTsStatusOutputTsNum Integer32
  apexOutputTsStatusProgramsPerTs Integer32
  apexOutputTsStatusServicesMapped Integer32
  apexOutputTsStatusAncillaryPidsMapped Integer32
  apexOutputTsStatusInputStreamsMapped Integer32
  apexOutputTsStatusFault INTEGER
  apexOutputTsStatusServicesInError Integer32
  apexOutputTsStatusDepiSessionsMapped Integer32
  apexOutputTsStatusMessageGenerationNum Integer32
  apexOutputTsStatusScgsProvisioned Integer32
  apexOutputTsStatusServicesMuxed Integer32

ApexPsiStatusEntry  
SEQUENCE    
  apexPsiStatusTableType INTEGER
  apexPsiStatusIndex Integer32
  apexPsiStatusPid Integer32
  apexPsiStatusMessageType Integer32
  apexPsiStatusProgramNumber Integer32
  apexPsiStatusSegment Integer32
  apexPsiStatusPart Integer32
  apexPsiStatusBody DisplayString
  apexPsiStatusGpsTime Integer32

ApexOutputProgramEntry  
SEQUENCE    
  apexOutputProgramIndex Integer32
  apexOutputProgramInputTsIndex Integer32
  apexOutputProgramInputProgNum Integer32
  apexOutputProgramOutputProgNum Integer32
  apexOutputProgramRoutingStatus DisplayString
  apexOutputProgramInputPreEncrypted INTEGER
  apexOutputProgramOutputTsNum Integer32
  apexOutputProgramError INTEGER
  apexOutputProgramEncryptionMode INTEGER
  apexOutputProgramEncryptionStatus DisplayString
  apexOutputProgramEcmServiceId Integer32
  apexOutputProgramCciLevel INTEGER
  apexOutputProgramApsLevel INTEGER
  apexOutputProgramCitSetting INTEGER
  apexOutputProgramNumberTiers Integer32
  apexOutputProgramTierData DisplayString
  apexOutputProgramSourceId Integer32
  apexOutputProgramProviderId Integer32
  apexOutputProgramProgramType INTEGER
  apexOutputProgramDtaEncryptionMode INTEGER

ApexAcpStatusEntry  
SEQUENCE    
  apexAcpStatusIndex Integer32
  apexAcpUnitAddress DisplayString
  apexAcpHealthByte Integer32
  apexAcpEvenCsn Integer32
  apexAcpOddCsn Integer32
  apexAcpUnitAttribute Integer32

ApexUdpMapApplyEntry  
SEQUENCE    
  apexUdpMapApplyOutputTsNum Integer32
  apexUdpMapApplyChange ApplyDataToDeviceTYPE

ApexUdpMapEntry  
SEQUENCE    
  apexUdpMapOutputTsNum Integer32
  apexUdpMapInputInterface Integer32
  apexUdpMapStartProgNum Integer32
  apexUdpMapNumberProgs Integer32

ApexUdpMapMulticastEntry  
SEQUENCE    
  apexUdpMapMulticastIndex Integer32
  apexUdpMapMulticastEnable EnableDisableTYPE
  apexUdpMapMulticastInterface Integer32
  apexUdpMapMulticastUdp Integer32
  apexUdpMapMulticastMcastIp IpAddress
  apexUdpMapMulticastSourceIp IpAddress

ApexUdpMapMulticastApplyEntry  
SEQUENCE    
  apexUdpMapMulticastApplyIndex Integer32
  apexUdpMapMulticastApplyChange ApplyDataToDeviceTYPE

ApexUdpMapStatusEntry  
SEQUENCE    
  apexUdpMapStatusOutputTsNum Integer32
  apexUdpMapInvalidApplyText DisplayString

ApexRdsEmmStatusEntry  
SEQUENCE    
  apexRdsEmmStatusIndex Integer32
  apexRdsEmmStatusCsn Integer32
  apexRdsEmmStatusState INTEGER
  apexRdsEmmStatusGpsTime Integer32
  apexRdsEmmStatusServerError Unsigned32
  apexRdsEmmStatusUnitAddress DisplayString

ApexRdsSourceLookupEntry  
SEQUENCE    
  apexRdsSourceLookupIndex Integer32
  apexRdsSourceLookupDescription DisplayString
  apexRdsSourceLookupSourceId Integer32
  apexRdsSourceLookupProviderId Integer32

ApexRdsEventEntry  
SEQUENCE    
  apexRdsEventProgramIndex Integer32
  apexRdsEventEventIndex Integer32
  apexRdsEventEpochNumber Integer32
  apexRdsEventEpochStart Integer32
  apexRdsEventEpochEnd Integer32
  apexRdsEventInterstitialDuration Integer32
  apexRdsEventPreviewDuration Integer32
  apexRdsEventPurchaseDuration Integer32
  apexRdsEventNumberTiers Integer32
  apexRdsEventTierData DisplayString
  apexRdsEventProgramCost Integer32
  apexRdsEventRatingRegion Integer32
  apexRdsEventRatingData DisplayString
  apexRdsEventRatingText DisplayString
  apexRdsEventControlByte DisplayString
  apexRdsEventPrkmWkemAvailable INTEGER
  apexRdsEventCcmAvailable INTEGER

ApexEncryptionMcDiagEntry  
SEQUENCE    
  apexEncryptionMcDiagDeviceIndex Integer32
  apexEncryptionCwCountsPerSecond Unsigned32

ApexEasOutputEntry  
SEQUENCE    
  apexEasOutputStreamNum Integer32
  apexEasOutputEnable EnableDisableTYPE

ApexEasServerApplyEntry  
SEQUENCE    
  apexEasServerApplyNum Integer32
  apexEasServerApplyChange ApplyDataToDeviceTYPE

ApexEasServerEntry  
SEQUENCE    
  apexEasServerNum Integer32
  apexEasServerPhysInType INTEGER
  apexEasServerPhysInPort Integer32
  apexEasServerRcvUdpPort Integer32
  apexEasServerMulticastIpAddress IpAddress
  apexEasServerSourceIpAddress IpAddress

ApexDtaConfigApplyEntry  
SEQUENCE    
  apexDtaConfigApplyIndex Integer32
  apexDtaConfigApplyChange ApplyDataToDeviceTYPE

ApexDtaRfPortConfigEntry  
SEQUENCE    
  apexDtaRfPortConfigIndex Integer32
  apexDtaRfPortConfigNetPidMulticastIP IpAddress
  apexDtaRfPortConfigNetPidSourceIP IpAddress
  apexDtaRfPortConfigNetPidUdpPort Integer32
  apexDtaRfPortConfigNetPidInterface EthernetInterfaceTYPE
  apexDtaRfPortConfigNetPidNum Integer32

ApexDtaOtsConfigEntry  
SEQUENCE    
  apexDtaOtsConfigIndex Integer32
  apexDtaOtsConfigEnable EnableDisableTYPE

ApexDepiControlConfigApplyEntry  
SEQUENCE    
  apexDepiControlConfigApplyIndex Integer32
  apexDepiControlConfigApplyChange ApplyDataToDeviceTYPE

ApexDepiControlConfigEntry  
SEQUENCE    
  apexDepiControlConfigIndex Integer32
  apexDepiControlConfigEnable EnableDisableTYPE
  apexDepiControlConfigInterfaceNumber Integer32
  apexDepiControlConfigSrcIpAddr IpAddress
  apexDepiControlConfigOverUdp INTEGER
  apexDepiControlConfigType INTEGER

ApexDepiControlStatusEntry  
SEQUENCE    
  apexDepiControlStatusIndex Integer32
  apexDepiControlStatusLocalUdp Integer32
  apexDepiControlStatusRemoteUdp Integer32
  apexDepiControlStatusConnectionStatus INTEGER
  apexDepiControlStatusUnknownCtl Unsigned32
  apexDepiControlStatusMalformedCtl Unsigned32
  apexDepiControlStatusUnknownAvp Unsigned32
  apexDepiControlStatusMalformedAvp Unsigned32
  apexDepiControlStatusInvalidVendorId Unsigned32
  apexDepiControlStatusHbitSet Unsigned32
  apexDepiControlStatusTotalSessions Unsigned32
  apexDepiControlStatusCurrentSessions Unsigned32
  apexDepiControlStatusRejectedSessions Unsigned32

ApexDepiSessionConfigApplyEntry  
SEQUENCE    
  apexDepiSessionConfigApplyOutputTsNum Integer32
  apexDepiSessionConfigApplyChange ApplyDataToDeviceTYPE

ApexDepiSessionConfigEntry  
SEQUENCE    
  apexDepiSessionConfigOutputTsNum Integer32
  apexDepiSessionConfigEnable EnableDisableTYPE
  apexDepiSessionConfigControlId Integer32
  apexDepiSessionConfigDocsisTsid Integer32
  apexDepiSessionConfigUdpPort Integer32
  apexDepiSessionConfigSyncCorrection EnableDisableTYPE

ApexDepiSessionStatusEntry  
SEQUENCE    
  apexDepiSessionStatusIndex Integer32
  apexDepiSessionStatusControlId Integer32
  apexDepiSessionStatusOutputQAMChannel Integer32
  apexDepiSessionStatusLocalUdp Integer32
  apexDepiSessionStatusRemoteUdp Integer32
  apexDepiSessionStatusStatus INTEGER
  apexDepiSessionStatusPerHopBehavior Integer32
  apexDepiSessionStatusUnknownCtl Unsigned32
  apexDepiSessionStatusMalformedCtl Unsigned32
  apexDepiSessionStatusUnknownAvp Unsigned32
  apexDepiSessionStatusMalformedAvp Unsigned32
  apexDepiSessionStatusInvalidVendorId Unsigned32
  apexDepiSessionStatusHbitSet Unsigned32
  apexDepiSessionStatusInSLIMsgs Unsigned32
  apexDepiSessionStatusOutSLIMsgs Unsigned32
  apexDepiSessionStatusIngressDlmMsgs Unsigned32
  apexDepiSessionStatusEgressDlmMsgs Unsigned32
  apexDepiSessionStatusLatencyStart Unsigned32
  apexDepiSessionStatusLatencyEnd Unsigned32
  apexDepiSessionStatusInDataPackets Unsigned32
  apexDepiSessionStatusInSequenceDiscards Unsigned32
  apexDepiSessionStatusInDataPacketDiscards Unsigned32
  apexDepiSessionStatusSessionID Unsigned32

ApexPsipStatusInputEntry  
SEQUENCE    
  apexPsipStatusInputIndex Integer32
  apexPsipStatusInputPid Integer32
  apexPsipStatusInputMessageType Integer32
  apexPsipStatusInputSourceId Integer32
  apexPsipStatusInputSegment Integer32
  apexPsipStatusInputPart Integer32
  apexPsipStatusInputBody DisplayString
  apexPsipStatusInputGpsTime Integer32
  apexPsipStatusInputInfo DisplayString

ApexPsipStatusOutputEntry  
SEQUENCE    
  apexPsipStatusOutputIndex Integer32
  apexPsipStatusOutputPid Integer32
  apexPsipStatusOutputMessageType Integer32
  apexPsipStatusOutputSourceId Integer32
  apexPsipStatusOutputSegment Integer32
  apexPsipStatusOutputPart Integer32
  apexPsipStatusOutputBody DisplayString
  apexPsipStatusOutputGpsTime Integer32

ApexPsipStatusServiceEntry  
SEQUENCE    
  apexPsipStatusServiceIndex Integer32
  apexPsipStatusServiceNum Integer32
  apexPsipStatusServiceOutputTs Integer32
  apexPsipStatusServiceState DisplayString
  apexPsipStatusServiceSourceId Integer32

ApexHwEventEntry  
SEQUENCE    
  apexHwEventIndex Integer32
  apexHwEventTimeLogged Integer32
  apexHwEventAlarmCode Integer32
  apexHwEventAlarmSeverity INTEGER
  apexHwEventData Integer32
  apexHwEventDescription DisplayString

ApexInvalidInitDataEntry  
SEQUENCE    
  apexInvalidInitDataIndex Integer32
  apexInvalidInitDataTimeLogged Integer32
  apexInvalidInitDataDescription DisplayString

ApexOutputTsEventEntry  
SEQUENCE    
  apexOutputTsEventIndex Integer32
  apexOutputTsEventTimeLogged Integer32
  apexOutputTsEventAlarmCode Integer32
  apexOutputTsEventAlarmSeverity INTEGER
  apexOutputTsEventOutputTsNum Integer32
  apexOutputTsEventCurRate Integer32
  apexOutputTsEventAvgRate Integer32
  apexOutputTsEventMinRate Integer32
  apexOutputTsEventPeakRate Integer32
  apexOutputTsEventCurDropPackets Integer32
  apexOutputTsEventPeakDropPackets Integer32
  apexOutputTsEventRollingDropPackets Integer32
  apexOutputTsEventTotalDropPackets Integer32
  apexOutputTsEventDescription DisplayString

ApexGbeInputTsEventEntry  
SEQUENCE    
  apexGbeInputTsEventIndex Integer32
  apexGbeInputTsEventTimeLogged Integer32
  apexGbeInputTsEventAlarmCode Integer32
  apexGbeInputTsEventAlarmSeverity INTEGER
  apexGbeInputTsEventRedundantConfig INTEGER
  apexGbeInputTsEventGbeInterface Integer32
  apexGbeInputTsEventUdpPort Integer32
  apexGbeInputTsEventMulticastIp IpAddress
  apexGbeInputTsEventSourceIp IpAddress
  apexGbeInputTsEventInputTsState InputTsStateTYPE
  apexGbeInputTsEventRateCompareType RateComparisonTYPE
  apexGbeInputTsEventSamplingPeriod Integer32
  apexGbeInputTsEventPriCurStreamCount Counter32
  apexGbeInputTsEventPriCurDataCount Counter32
  apexGbeInputTsEventSecCurStreamCount Counter32
  apexGbeInputTsEventSecCurDataCount Counter32
  apexGbeInputTsEventDescription DisplayString

ApexRtspEventEntry  
SEQUENCE    
  apexRtspEventIndex Integer32
  apexRtspEventTimeLogged Integer32
  apexRtspEventControllerIp IpAddress
  apexRtspEventSessionCount Integer32
  apexRtspEventSourceDescription DisplayString
  apexRtspEventDescription DisplayString

ApexMappingErrorEntry  
SEQUENCE    
  apexMappingErrorIndex Integer32
  apexMappingErrorTimeLogged Integer32
  apexMappingErrorCode Integer32
  apexMappingErrorMappingType INTEGER
  apexMappingErrorInputType INTEGER
  apexMappingErrorInputInterface Integer32
  apexMappingErrorUdpPort Integer32
  apexMappingErrorMulticastIp IpAddress
  apexMappingErrorSourceIp IpAddress
  apexMappingErrorInputProgramPid Integer32
  apexMappingErrorOutputProgramPid Integer32
  apexMappingErrorOutputOpMode INTEGER
  apexMappingErrorOutputTsNum Integer32
  apexMappingErrorSecInputInterface Integer32
  apexMappingErrorSecUdpPort Integer32
  apexMappingErrorSecMulticastIp IpAddress
  apexMappingErrorSecSourceIp IpAddress

ApexChassisRedundancyEventEntry  
SEQUENCE    
  apexChassisRedundancyEventIndex Integer32
  apexChassisRedundancyEventTimeLogged Integer32
  apexChassisRedundancyEventDescription DisplayString

Defined Values

apex 1.3.6.1.4.1.1166.1.31
The MIB module for the APEX.
MODULE-IDENTITY    

apexSys 1.3.6.1.4.1.1166.1.31.1
OBJECT IDENTIFIER    

apexSysConfig 1.3.6.1.4.1.1166.1.31.1.1
OBJECT IDENTIFIER    

apexSysConfigGeneral 1.3.6.1.4.1.1166.1.31.1.1.1
OBJECT IDENTIFIER    

apexSysConfigMcEmmInsertion 1.3.6.1.4.1.1166.1.31.1.1.2
OBJECT IDENTIFIER    

apexSysStatus 1.3.6.1.4.1.1166.1.31.1.2
OBJECT IDENTIFIER    

apexSysStatusGeneral 1.3.6.1.4.1.1166.1.31.1.2.1
OBJECT IDENTIFIER    

apexSysStatusVersions 1.3.6.1.4.1.1166.1.31.1.2.2
OBJECT IDENTIFIER    

apexTime 1.3.6.1.4.1.1166.1.31.2
OBJECT IDENTIFIER    

apexTimeConfig 1.3.6.1.4.1.1166.1.31.2.1
OBJECT IDENTIFIER    

apexTimeConfigGeneral 1.3.6.1.4.1.1166.1.31.2.1.1
OBJECT IDENTIFIER    

apexTimeStatus 1.3.6.1.4.1.1166.1.31.2.2
OBJECT IDENTIFIER    

apexTimeStatusGeneral 1.3.6.1.4.1.1166.1.31.2.2.1
OBJECT IDENTIFIER    

apexTemperature 1.3.6.1.4.1.1166.1.31.3
OBJECT IDENTIFIER    

apexTemperatureConfig 1.3.6.1.4.1.1166.1.31.3.1
OBJECT IDENTIFIER    

apexTemperatureConfigGeneral 1.3.6.1.4.1.1166.1.31.3.1.1
OBJECT IDENTIFIER    

apexTemperatureStatus 1.3.6.1.4.1.1166.1.31.3.2
OBJECT IDENTIFIER    

apexTemperatureStatusGeneral 1.3.6.1.4.1.1166.1.31.3.2.1
OBJECT IDENTIFIER    

apexMainBoardTemperature 1.3.6.1.4.1.1166.1.31.3.2.2
OBJECT IDENTIFIER    

apexMainBoardTemperatureFault 1.3.6.1.4.1.1166.1.31.3.2.3
OBJECT IDENTIFIER    

apexPowerSupply 1.3.6.1.4.1.1166.1.31.4
OBJECT IDENTIFIER    

apexPsConfig 1.3.6.1.4.1.1166.1.31.4.1
OBJECT IDENTIFIER    

apexPsConfigGeneral 1.3.6.1.4.1.1166.1.31.4.1.1
OBJECT IDENTIFIER    

apexPsStatus 1.3.6.1.4.1.1166.1.31.4.2
OBJECT IDENTIFIER    

apexPsStatusGeneral 1.3.6.1.4.1.1166.1.31.4.2.1
OBJECT IDENTIFIER    

apexAsi 1.3.6.1.4.1.1166.1.31.5
OBJECT IDENTIFIER    

apexAsiConfig 1.3.6.1.4.1.1166.1.31.5.1
OBJECT IDENTIFIER    

apexAsiMonitorPortConfig 1.3.6.1.4.1.1166.1.31.5.1.2
OBJECT IDENTIFIER    

apexFastEnet 1.3.6.1.4.1.1166.1.31.6
OBJECT IDENTIFIER    

apexFastEnetConfig 1.3.6.1.4.1.1166.1.31.6.1
OBJECT IDENTIFIER    

apexFastEnetConfigGeneral 1.3.6.1.4.1.1166.1.31.6.1.1
OBJECT IDENTIFIER    

apexFastEnetStatus 1.3.6.1.4.1.1166.1.31.6.2
OBJECT IDENTIFIER    

apexFastEnetStatusGeneral 1.3.6.1.4.1.1166.1.31.6.2.1
OBJECT IDENTIFIER    

apexOamp 1.3.6.1.4.1.1166.1.31.6.3
OBJECT IDENTIFIER    

apexOampConfig 1.3.6.1.4.1.1166.1.31.6.3.1
OBJECT IDENTIFIER    

apexOampConfigGeneral 1.3.6.1.4.1.1166.1.31.6.3.1.1
OBJECT IDENTIFIER    

apexOampStatus 1.3.6.1.4.1.1166.1.31.6.3.2
OBJECT IDENTIFIER    

apexOampStatusGeneral 1.3.6.1.4.1.1166.1.31.6.3.2.1
OBJECT IDENTIFIER    

apexDataIp 1.3.6.1.4.1.1166.1.31.6.4
OBJECT IDENTIFIER    

apexDataIpConfig 1.3.6.1.4.1.1166.1.31.6.4.1
OBJECT IDENTIFIER    

apexDataIpConfigGeneral 1.3.6.1.4.1.1166.1.31.6.4.1.1
OBJECT IDENTIFIER    

apexDataIpStatus 1.3.6.1.4.1.1166.1.31.6.4.2
OBJECT IDENTIFIER    

apexDataIpStatusGeneral 1.3.6.1.4.1.1166.1.31.6.4.2.1
OBJECT IDENTIFIER    

apexGbe 1.3.6.1.4.1.1166.1.31.7
OBJECT IDENTIFIER    

apexGbeConfig 1.3.6.1.4.1.1166.1.31.7.1
OBJECT IDENTIFIER    

apexGbeConfigGeneral 1.3.6.1.4.1.1166.1.31.7.1.1
OBJECT IDENTIFIER    

apexGbeConfigInputRedundancy 1.3.6.1.4.1.1166.1.31.7.1.4
OBJECT IDENTIFIER    

apexGbeConfigInputRedundancyGeneral 1.3.6.1.4.1.1166.1.31.7.1.4.1
OBJECT IDENTIFIER    

apexGbeConfigInterfaceRedundancy 1.3.6.1.4.1.1166.1.31.7.1.7
OBJECT IDENTIFIER    

apexGbeConfigInterfaceRedundancyGeneral 1.3.6.1.4.1.1166.1.31.7.1.7.1
OBJECT IDENTIFIER    

apexGbeStatus 1.3.6.1.4.1.1166.1.31.7.2
OBJECT IDENTIFIER    

apexGbeStatusGeneral 1.3.6.1.4.1.1166.1.31.7.2.1
OBJECT IDENTIFIER    

apexGbeStatusFrameCounter 1.3.6.1.4.1.1166.1.31.7.2.6
OBJECT IDENTIFIER    

apexGbeStatusFrameCounterGeneral 1.3.6.1.4.1.1166.1.31.7.2.6.1
OBJECT IDENTIFIER    

apexGbeFrameBufferStats 1.3.6.1.4.1.1166.1.31.7.2.7
OBJECT IDENTIFIER    

apexGbeFrameBufferStatsGeneral 1.3.6.1.4.1.1166.1.31.7.2.7.1
OBJECT IDENTIFIER    

apexGbeStatusInputTransportStream 1.3.6.1.4.1.1166.1.31.7.2.8
OBJECT IDENTIFIER    

apexGbeStatusInputTsGeneral 1.3.6.1.4.1.1166.1.31.7.2.8.1
OBJECT IDENTIFIER    

apexGbeStatusInterfaceRedund 1.3.6.1.4.1.1166.1.31.7.2.9
OBJECT IDENTIFIER    

apexGbeSfp 1.3.6.1.4.1.1166.1.31.7.3
OBJECT IDENTIFIER    

apexGbeSfpConfig 1.3.6.1.4.1.1166.1.31.7.3.1
OBJECT IDENTIFIER    

apexGbeSfpConfigGeneral 1.3.6.1.4.1.1166.1.31.7.3.1.1
OBJECT IDENTIFIER    

apexGbeSfpStatus 1.3.6.1.4.1.1166.1.31.7.3.2
OBJECT IDENTIFIER    

apexGbeSfpStatusGeneral 1.3.6.1.4.1.1166.1.31.7.3.2.1
OBJECT IDENTIFIER    

apexQam 1.3.6.1.4.1.1166.1.31.8
OBJECT IDENTIFIER    

apexQamConfig 1.3.6.1.4.1.1166.1.31.8.1
OBJECT IDENTIFIER    

apexQamConfigGeneral 1.3.6.1.4.1.1166.1.31.8.1.1
OBJECT IDENTIFIER    

apexQamModuleUpgrade 1.3.6.1.4.1.1166.1.31.8.1.2
OBJECT IDENTIFIER    

apexQamRfRedundancyConfig 1.3.6.1.4.1.1166.1.31.8.1.6
OBJECT IDENTIFIER    

apexQamRfRedundancyConfigGeneral 1.3.6.1.4.1.1166.1.31.8.1.6.1
OBJECT IDENTIFIER    

apexQamStatus 1.3.6.1.4.1.1166.1.31.8.2
OBJECT IDENTIFIER    

apexQamStatusGeneral 1.3.6.1.4.1.1166.1.31.8.2.1
OBJECT IDENTIFIER    

apexQamRfRedundancyStatus 1.3.6.1.4.1.1166.1.31.8.2.7
OBJECT IDENTIFIER    

apexQamRfRedundancyStatusGeneral 1.3.6.1.4.1.1166.1.31.8.2.7.1
OBJECT IDENTIFIER    

apexQrmDownload 1.3.6.1.4.1.1166.1.31.8.3
OBJECT IDENTIFIER    

apexQrmDownloadConfig 1.3.6.1.4.1.1166.1.31.8.3.1
OBJECT IDENTIFIER    

apexQrmDownloadConfigGeneral 1.3.6.1.4.1.1166.1.31.8.3.1.1
OBJECT IDENTIFIER    

apexQrmDownloadStatus 1.3.6.1.4.1.1166.1.31.8.3.2
OBJECT IDENTIFIER    

apexQrmDownloadStatusGeneral 1.3.6.1.4.1.1166.1.31.8.3.2.1
OBJECT IDENTIFIER    

apexSessionControl 1.3.6.1.4.1.1166.1.31.9
OBJECT IDENTIFIER    

apexSessionControlConfig 1.3.6.1.4.1.1166.1.31.9.1
OBJECT IDENTIFIER    

apexSessionControlConfigGeneral 1.3.6.1.4.1.1166.1.31.9.1.1
OBJECT IDENTIFIER    

apexSessionControlStatus 1.3.6.1.4.1.1166.1.31.9.2
OBJECT IDENTIFIER    

apexSessionControlStatusGeneral 1.3.6.1.4.1.1166.1.31.9.2.1
OBJECT IDENTIFIER    

apexRpc 1.3.6.1.4.1.1166.1.31.9.3
OBJECT IDENTIFIER    

apexRpcConfig 1.3.6.1.4.1.1166.1.31.9.3.1
OBJECT IDENTIFIER    

apexRpcConfigGeneral 1.3.6.1.4.1.1166.1.31.9.3.1.1
OBJECT IDENTIFIER    

apexRpcStatus 1.3.6.1.4.1.1166.1.31.9.3.2
OBJECT IDENTIFIER    

apexRpcStatusGeneral 1.3.6.1.4.1.1166.1.31.9.3.2.1
OBJECT IDENTIFIER    

apexRtsp 1.3.6.1.4.1.1166.1.31.9.4
OBJECT IDENTIFIER    

apexRtspConfig 1.3.6.1.4.1.1166.1.31.9.4.1
OBJECT IDENTIFIER    

apexRtspConfigGeneral 1.3.6.1.4.1.1166.1.31.9.4.1.1
OBJECT IDENTIFIER    

apexRtspConfMhaGeneral 1.3.6.1.4.1.1166.1.31.9.4.1.9
OBJECT IDENTIFIER    

apexRtspConfMhaSbe 1.3.6.1.4.1.1166.1.31.9.4.1.10
OBJECT IDENTIFIER    

apexRtspStatus 1.3.6.1.4.1.1166.1.31.9.4.2
OBJECT IDENTIFIER    

apexRtspStatusGeneral 1.3.6.1.4.1.1166.1.31.9.4.2.1
OBJECT IDENTIFIER    

apexManualRouting 1.3.6.1.4.1.1166.1.31.10
OBJECT IDENTIFIER    

apexManualRoutingConfig 1.3.6.1.4.1.1166.1.31.10.1
OBJECT IDENTIFIER    

apexManualRoutingConfigGeneral 1.3.6.1.4.1.1166.1.31.10.1.1
OBJECT IDENTIFIER    

apexManualRouteGbeInputRedundConfig 1.3.6.1.4.1.1166.1.31.10.1.6
OBJECT IDENTIFIER    

apexManRteGbeInRedConfigGeneral 1.3.6.1.4.1.1166.1.31.10.1.6.1
OBJECT IDENTIFIER    

apexManualRoutingStatus 1.3.6.1.4.1.1166.1.31.10.2
OBJECT IDENTIFIER    

apexManualRoutingStatusGeneral 1.3.6.1.4.1.1166.1.31.10.2.1
OBJECT IDENTIFIER    

apexManualRouteGbeInputRedundStatus 1.3.6.1.4.1.1166.1.31.10.2.2
OBJECT IDENTIFIER    

apexManRteGbeInRedStatusGeneral 1.3.6.1.4.1.1166.1.31.10.2.2.1
OBJECT IDENTIFIER    

apexAncillaryPidMapping 1.3.6.1.4.1.1166.1.31.11
OBJECT IDENTIFIER    

apexPidMapConfig 1.3.6.1.4.1.1166.1.31.11.1
OBJECT IDENTIFIER    

apexPidMapStatus 1.3.6.1.4.1.1166.1.31.11.2
OBJECT IDENTIFIER    

apexPidMapStatusGeneral 1.3.6.1.4.1.1166.1.31.11.2.1
OBJECT IDENTIFIER    

apexInsertion 1.3.6.1.4.1.1166.1.31.12
OBJECT IDENTIFIER    

apexInsertionConfig 1.3.6.1.4.1.1166.1.31.12.1
OBJECT IDENTIFIER    

apexInsertionConfigGeneral 1.3.6.1.4.1.1166.1.31.12.1.1
OBJECT IDENTIFIER    

apexInsertionStatus 1.3.6.1.4.1.1166.1.31.12.2
OBJECT IDENTIFIER    

apexInsertionStatusGeneral 1.3.6.1.4.1.1166.1.31.12.2.1
OBJECT IDENTIFIER    

apexInputTransport 1.3.6.1.4.1.1166.1.31.13
OBJECT IDENTIFIER    

apexInputTsConfig 1.3.6.1.4.1.1166.1.31.13.1
OBJECT IDENTIFIER    

apexInputTsConfigGeneral 1.3.6.1.4.1.1166.1.31.13.1.1
OBJECT IDENTIFIER    

apexInputTsStatus 1.3.6.1.4.1.1166.1.31.13.2
OBJECT IDENTIFIER    

apexInputTsStatusGeneral 1.3.6.1.4.1.1166.1.31.13.2.1
OBJECT IDENTIFIER    

apexOutputTransport 1.3.6.1.4.1.1166.1.31.14
OBJECT IDENTIFIER    

apexOutputTsConfig 1.3.6.1.4.1.1166.1.31.14.1
OBJECT IDENTIFIER    

apexOutputTsConfigGeneral 1.3.6.1.4.1.1166.1.31.14.1.1
OBJECT IDENTIFIER    

apexOutputTsUtilizationMonitoring 1.3.6.1.4.1.1166.1.31.14.1.4
OBJECT IDENTIFIER    

apexOutputTsUtilizationMonitorGeneral 1.3.6.1.4.1.1166.1.31.14.1.4.1
OBJECT IDENTIFIER    

apexOutputTsStatus 1.3.6.1.4.1.1166.1.31.14.2
OBJECT IDENTIFIER    

apexOutputTsStatusGeneral 1.3.6.1.4.1.1166.1.31.14.2.1
OBJECT IDENTIFIER    

apexOutputTsUtilization 1.3.6.1.4.1.1166.1.31.14.2.2
OBJECT IDENTIFIER    

apexOutputTsUtilizationGeneral 1.3.6.1.4.1.1166.1.31.14.2.2.1
OBJECT IDENTIFIER    

apexPsi 1.3.6.1.4.1.1166.1.31.15
OBJECT IDENTIFIER    

apexPsiConfig 1.3.6.1.4.1.1166.1.31.15.1
OBJECT IDENTIFIER    

apexPsiConfigGeneral 1.3.6.1.4.1.1166.1.31.15.1.1
OBJECT IDENTIFIER    

apexPsiStatus 1.3.6.1.4.1.1166.1.31.15.2
OBJECT IDENTIFIER    

apexPsiStatusGeneral 1.3.6.1.4.1.1166.1.31.15.2.1
OBJECT IDENTIFIER    

apexOutputProgram 1.3.6.1.4.1.1166.1.31.16
OBJECT IDENTIFIER    

apexOutputProgramConfig 1.3.6.1.4.1.1166.1.31.16.1
OBJECT IDENTIFIER    

apexOutputProgramConfigGeneral 1.3.6.1.4.1.1166.1.31.16.1.1
OBJECT IDENTIFIER    

apexOutputProgramStatus 1.3.6.1.4.1.1166.1.31.16.2
OBJECT IDENTIFIER    

apexOutputProgramStatusGeneral 1.3.6.1.4.1.1166.1.31.16.2.1
OBJECT IDENTIFIER    

apexAcp 1.3.6.1.4.1.1166.1.31.17
OBJECT IDENTIFIER    

apexAcpConfig 1.3.6.1.4.1.1166.1.31.17.1
OBJECT IDENTIFIER    

apexAcpConfigGeneral 1.3.6.1.4.1.1166.1.31.17.1.1
OBJECT IDENTIFIER    

apexAcpStatus 1.3.6.1.4.1.1166.1.31.17.2
OBJECT IDENTIFIER    

apexAcpStatusGeneral 1.3.6.1.4.1.1166.1.31.17.2.1
OBJECT IDENTIFIER    

apexUdpPortMapping 1.3.6.1.4.1.1166.1.31.18
OBJECT IDENTIFIER    

apexUdpMapConfig 1.3.6.1.4.1.1166.1.31.18.1
OBJECT IDENTIFIER    

apexUdpMapConfigGeneral 1.3.6.1.4.1.1166.1.31.18.1.1
OBJECT IDENTIFIER    

apexUdpMapStatus 1.3.6.1.4.1.1166.1.31.18.2
OBJECT IDENTIFIER    

apexUdpMapStatusGeneral 1.3.6.1.4.1.1166.1.31.18.2.1
OBJECT IDENTIFIER    

apexRds 1.3.6.1.4.1.1166.1.31.19
OBJECT IDENTIFIER    

apexRdsConfig 1.3.6.1.4.1.1166.1.31.19.1
OBJECT IDENTIFIER    

apexRdsConfigGeneral 1.3.6.1.4.1.1166.1.31.19.1.1
OBJECT IDENTIFIER    

apexRdsStatus 1.3.6.1.4.1.1166.1.31.19.2
OBJECT IDENTIFIER    

apexRdsStatusGeneral 1.3.6.1.4.1.1166.1.31.19.2.1
OBJECT IDENTIFIER    

apexEncryption 1.3.6.1.4.1.1166.1.31.20
OBJECT IDENTIFIER    

apexEncryptionConfig 1.3.6.1.4.1.1166.1.31.20.1
OBJECT IDENTIFIER    

apexEncryptionConfigGeneral 1.3.6.1.4.1.1166.1.31.20.1.1
OBJECT IDENTIFIER    

apexCteConfig 1.3.6.1.4.1.1166.1.31.20.1.2
OBJECT IDENTIFIER    

apexEncryptionStatus 1.3.6.1.4.1.1166.1.31.20.2
OBJECT IDENTIFIER    

apexEncryptionStatusGeneral 1.3.6.1.4.1.1166.1.31.20.2.1
OBJECT IDENTIFIER    

apexEncryptionCwgStatus 1.3.6.1.4.1.1166.1.31.20.2.1.2
OBJECT IDENTIFIER    

apexEas 1.3.6.1.4.1.1166.1.31.21
OBJECT IDENTIFIER    

apexEasConfig 1.3.6.1.4.1.1166.1.31.21.1
OBJECT IDENTIFIER    

apexEasConfigGeneral 1.3.6.1.4.1.1166.1.31.21.1.1
OBJECT IDENTIFIER    

apexEasStatus 1.3.6.1.4.1.1166.1.31.21.2
OBJECT IDENTIFIER    

apexEasStatusGeneral 1.3.6.1.4.1.1166.1.31.21.2.1
OBJECT IDENTIFIER    

apexChassisRedundancy 1.3.6.1.4.1.1166.1.31.22
OBJECT IDENTIFIER    

apexChassisRedundancyConfig 1.3.6.1.4.1.1166.1.31.22.1
OBJECT IDENTIFIER    

apexChassisRedundancyConfigGeneral 1.3.6.1.4.1.1166.1.31.22.1.1
OBJECT IDENTIFIER    

apexChassisRedundancyStatus 1.3.6.1.4.1.1166.1.31.22.2
OBJECT IDENTIFIER    

apexChassisRedundancyStatusGeneral 1.3.6.1.4.1.1166.1.31.22.2.1
OBJECT IDENTIFIER    

apexDta 1.3.6.1.4.1.1166.1.31.23
OBJECT IDENTIFIER    

apexDtaConfig 1.3.6.1.4.1.1166.1.31.23.1
OBJECT IDENTIFIER    

apexDtaGeneralConfig 1.3.6.1.4.1.1166.1.31.23.1.1
OBJECT IDENTIFIER    

apexDepi 1.3.6.1.4.1.1166.1.31.24
OBJECT IDENTIFIER    

apexDepiConfig 1.3.6.1.4.1.1166.1.31.24.1
OBJECT IDENTIFIER    

apexDepiConfigGeneral 1.3.6.1.4.1.1166.1.31.24.1.1
OBJECT IDENTIFIER    

apexDepiStatus 1.3.6.1.4.1.1166.1.31.24.2
OBJECT IDENTIFIER    

apexDepiStatusGeneral 1.3.6.1.4.1.1166.1.31.24.2.1
OBJECT IDENTIFIER    

apexDepiControl 1.3.6.1.4.1.1166.1.31.24.3
OBJECT IDENTIFIER    

apexDepiControlConfig 1.3.6.1.4.1.1166.1.31.24.3.1
OBJECT IDENTIFIER    

apexDepiControlConfigGeneral 1.3.6.1.4.1.1166.1.31.24.3.1.1
OBJECT IDENTIFIER    

apexDepiControlStatus 1.3.6.1.4.1.1166.1.31.24.3.2
OBJECT IDENTIFIER    

apexDepiControlStatusGeneral 1.3.6.1.4.1.1166.1.31.24.3.2.1
OBJECT IDENTIFIER    

apexDepiSession 1.3.6.1.4.1.1166.1.31.24.4
OBJECT IDENTIFIER    

apexDepiSessionConfig 1.3.6.1.4.1.1166.1.31.24.4.1
OBJECT IDENTIFIER    

apexDepiSessionStatus 1.3.6.1.4.1.1166.1.31.24.4.2
OBJECT IDENTIFIER    

apexDepiSessionStatusGeneral 1.3.6.1.4.1.1166.1.31.24.4.2.1
OBJECT IDENTIFIER    

apexPsip 1.3.6.1.4.1.1166.1.31.25
OBJECT IDENTIFIER    

apexPsipConfig 1.3.6.1.4.1.1166.1.31.25.1
OBJECT IDENTIFIER    

apexPsipConfigGeneral 1.3.6.1.4.1.1166.1.31.25.1.1
OBJECT IDENTIFIER    

apexPsipConfigTime 1.3.6.1.4.1.1166.1.31.25.1.2
OBJECT IDENTIFIER    

apexPsipStatus 1.3.6.1.4.1.1166.1.31.25.2
OBJECT IDENTIFIER    

apexPsipStatusGeneral 1.3.6.1.4.1.1166.1.31.25.2.1
OBJECT IDENTIFIER    

apexPreencryption 1.3.6.1.4.1.1166.1.31.26
OBJECT IDENTIFIER    

apexPreencryptionConfig 1.3.6.1.4.1.1166.1.31.26.1
OBJECT IDENTIFIER    

apexPreencryptionConfigGeneral 1.3.6.1.4.1.1166.1.31.26.1.1
OBJECT IDENTIFIER    

apexAlarms 1.3.6.1.4.1.1166.1.31.100
OBJECT IDENTIFIER    

apexEvents 1.3.6.1.4.1.1166.1.31.101
OBJECT IDENTIFIER    

apexConfigAlarms 1.3.6.1.4.1.1166.1.31.102
OBJECT IDENTIFIER    

apexConfAlarmEnable 1.3.6.1.4.1.1166.1.31.102.1
OBJECT IDENTIFIER    

apexConfAlarmClear 1.3.6.1.4.1.1166.1.31.102.2
OBJECT IDENTIFIER    

apexLogs 1.3.6.1.4.1.1166.1.31.200
OBJECT IDENTIFIER    

apexTraps 1.3.6.1.4.1.1166.1.31.0
OBJECT IDENTIFIER    

apexDebug 1.3.6.1.4.1.1166.1.31.5000
OBJECT IDENTIFIER    

apexSaveConfig 1.3.6.1.4.1.1166.1.31.1.1.1.1
Writing this object will commit the current configuration to Flash. While a read returns the value savingConfigToFlash, the flash is being saved; the save may not have been initiated by an SNMP set. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER saveNotInProgress(1), startSaveToFlash(2), savingConfigToFlash(3)  

apexProductName 1.3.6.1.4.1.1166.1.31.1.1.1.2
This is the Product Name of the APEX loaded at initialization from the config.ini file. Specific configurations of the APEX have specific purposes and are identified by their product name. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2, default=yes) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexBootMethod 1.3.6.1.4.1.1166.1.31.1.1.1.3
This parameter is used to set the boot method for the APEX. Selection of noDhcpOrBootp means the APEX will not use DHCP or BOOTP - this will result in about a 10 second savings in boot time. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noDhcpOrBootp(1), bootpOnly(3)  

apexAutoRebootEnable 1.3.6.1.4.1.1166.1.31.1.1.1.4
Setting to 'enabled' allows the APEX to automatically reboot when specific APEX hardware errors occur. Setting this to Enabled will cause the APEX to automatically reboot upon specific HW faults, such as a GigE processor crash, or upon a Host processor watchdog event. When disabled, HW faults and watchdog events will not cause an automatic reboot. This is useful when it is necessary to debug the event (to allow time to gather status prior to manually rebooting). Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexMcEmmInsertionMode 1.3.6.1.4.1.1166.1.31.1.1.2.1
Specify the mode in which MediaCipher EMMs are inserted, out of band or full in band. Once written, the change to this parameter will only take immediate effect after apexMcEmmInsertionApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexMcEmmInsertionApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER outOfBand(1), fullInBand(2)  

apexMcEmmInsertionPid1Enable 1.3.6.1.4.1.1166.1.31.1.1.2.2
Enable/disable first EMM PID to include in the CAT for MediaCipher Full In Band mode. Default value is enabled. Once written, the change to this parameter will only take immediate effect after apexMcEmmInsertionApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexMcEmmInsertionApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexMcEmmInsertionPid1 1.3.6.1.4.1.1166.1.31.1.1.2.3
First EMM PID to include in the CAT for MediaCipher Full In Band mode. Allowed values: from 0x1C00 to 0x1FFE. Default value is 0x1C02. Once written, the change to this parameter will only take immediate effect after apexMcEmmInsertionApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexMcEmmInsertionApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 7168..8190  

apexMcEmmInsertionPid2Enable 1.3.6.1.4.1.1166.1.31.1.1.2.4
Enable/disable first EMM PID to include in the CAT for MediaCipher Full In Band mode. Default value is disabled. Once written, the change to this parameter will only take immediate effect after apexMcEmmInsertionApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexMcEmmInsertionApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexMcEmmInsertionPid2 1.3.6.1.4.1.1166.1.31.1.1.2.5
Second EMM PID to include in the CAT for MediaCipher Full In Band mode. Allowed values: from 0x1C00 to 0x1FFE. Default value is 0x1C03. Once written, the change to this parameter will only take immediate effect after apexMcEmmInsertionApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexMcEmmInsertionApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 7168..8190  

apexMcEmmInsertionApplyChange 1.3.6.1.4.1.1166.1.31.1.1.2.6
The Apply for the MediaCipher EMM Insertion group. This parameter MUST be set to 'apply' in order for any of the data in the MC EMM Insertion group to take effect in the device. This parameter MUST be set LAST after all other data in the MC Emm Insertion group has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexBootReason 1.3.6.1.4.1.1166.1.31.1.2.1.1
Indicates reason for APEX boot: 'powerCycle' - Power-up or power cycled. 'operatorReboot' - Operator commanded reboot (refer to manual). 'hwFault' - Automatic reboot occurred as per apexAutoRebootEnable. 'wdFault' - Automatic Watchdog reboot as per apexAutoRebootEnable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER powerCycle(0), operatorReboot(1), hwFault(2), wdFault(3)  

apexMaxServiceMappings 1.3.6.1.4.1.1166.1.31.1.2.1.2
Maximum number of service mappings supported by the APEX.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexHostProcessorBootCodeVersion 1.3.6.1.4.1.1166.1.31.1.2.2.1
APEX Host Processor Boot Code Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexMuxFpgaVersion 1.3.6.1.4.1.1166.1.31.1.2.2.2
APEX MUX FPGA Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexMuxFpgaEncryption 1.3.6.1.4.1.1166.1.31.1.2.2.3
APEX MUX FPGA Encryption type currently loaded.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noEncryption(0), des(1), csa(2), aes(3)  

apexMainBoardVersion 1.3.6.1.4.1.1166.1.31.1.2.2.4
APEX Main Board Version. This is the revision of the apexMainBoardType.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexHostApplicationDate 1.3.6.1.4.1.1166.1.31.1.2.2.5
APEX Host Processor Application Creation Date.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexProductType 1.3.6.1.4.1.1166.1.31.1.2.2.6
APEX Product Type. The corresponding product name text setting can be found in identUnitModel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(0), apex1000(1)  

apexMainBoardType 1.3.6.1.4.1.1166.1.31.1.2.2.7
APEX Main Board Type. The revision is found in apexMainBoardVersion.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGlueFpgaVersion 1.3.6.1.4.1.1166.1.31.1.2.2.8
APEX Glue FPGA Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexGlueCpldVersion 1.3.6.1.4.1.1166.1.31.1.2.2.9
APEX Glue CPLD Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexDtiFpgaVersion 1.3.6.1.4.1.1166.1.31.1.2.2.10
APEX DTI FPGA Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexMpc2FpgaVersion 1.3.6.1.4.1.1166.1.31.1.2.2.11
APEX MPC2 FPGA Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexDpmVersion 1.3.6.1.4.1.1166.1.31.1.2.2.12
APEX DPM Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexTimeSource 1.3.6.1.4.1.1166.1.31.2.1.1.1
The source for system time. The time source can be configured to come from an SNTP time source, or be generated internally. When configured as internal: - The APEX will internally keep time starting at GPS time 0. A user can set the time to a valid GPS time in this mode. - The system time and UTC offset in internal mode are not updated and therefore are not valid. When configured to receive time via SNTP the SntpServerSpecified object and SntpServiceIP objects can be used to optionally define the SNTP server. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER sntp(1), internal(2)  

apexSntpUtcOffset 1.3.6.1.4.1.1166.1.31.2.1.1.2
The value of this object is the Universal Time Coordinated (UTC) offset from GPS time. Subtract this from GPS time to convert from GPS to UTC. Units are seconds. When time source is SNTP, this object can be set to specify the UTC offset that the APEX will use in calculating GPS time. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1000  

apexSntpServerSpecified 1.3.6.1.4.1.1166.1.31.2.1.1.3
When the TimeSource is SNTP, this object specifies whether the APEX will only accept time for a single SNTP server or from any server that broadcasts time. When notSpecified, the APEX will accept time from any SNTP server. When specified, the APEX will poll for time from the address of the SNTP server specified by the SntpServerIP address object. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSpecified(1), specified(2)  

apexSntpServerIpAddr 1.3.6.1.4.1.1166.1.31.2.1.1.4
This contains the IP address of the specified SNTP server. If apexTimeSource is SNTP and apexSntpServerSpecified is set to specified, then the apex will poll for time from this IP address. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexUserSuppliedTime 1.3.6.1.4.1.1166.1.31.2.1.1.5
The value of this object is the GPS Time the APEX is given via user entry. The time is reported in GPS seconds. This time is ONLY used when the APEX is set to Internal time mode. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

apexSystemTime 1.3.6.1.4.1.1166.1.31.2.2.1.1
The value of this object is the current System Time of the APEX. The system time is reported in GPS seconds. To determine the APEXs system time in UTC the apexSntpUtcOffset object must also be read and used in the calculation.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOperationalTime 1.3.6.1.4.1.1166.1.31.2.2.1.8
The Operational Time is the time in seconds since the APEX completed the boot sequence. It is the time that the APEX has been operational.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMainBoardTempFrontIntake 1.3.6.1.4.1.1166.1.31.3.2.2.1
Ambient temperature at the intake vent at the front of the unit. Measured in whole number degrees Celsius.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMainBoardTempMuxFpga 1.3.6.1.4.1.1166.1.31.3.2.2.2
Ambient temperature at the MUX FPGAs. Measured in whole number degrees Celsius.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMainBoardTempAcpModule 1.3.6.1.4.1.1166.1.31.3.2.2.3
Ambient temperature at the ACP Module location. This reading is valid for all models whether an ACP Module is standard on the model. Measured in whole number degrees Celsius.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMainBoardTempHostProcessor 1.3.6.1.4.1.1166.1.31.3.2.2.4
Ambient temperature at the Host Processor. Measured in whole number degrees Celsius.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMainBoardTempFrontIntakeFault 1.3.6.1.4.1.1166.1.31.3.2.3.1
Fault status of ambient temperature at the intake vent at the front of the unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), overTemp(2)  

apexMainBoardTempMuxFpgaFault 1.3.6.1.4.1.1166.1.31.3.2.3.2
Fault status of ambient temperature at the MUX FPGAs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), overTemp(2)  

apexMainBoardTempAcpModuleFault 1.3.6.1.4.1.1166.1.31.3.2.3.3
Fault status of ambient temperature at the ACP Module location.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), overTemp(2)  

apexMainBoardTempHostProcessorFault 1.3.6.1.4.1.1166.1.31.3.2.3.4
Fault status of ambient temperature at the Host Processor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), overTemp(2)  

apexPsStatusTable 1.3.6.1.4.1.1166.1.31.4.2.2
This is a table of status parameters for the two Power Supplies.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexPsStatusEntry

apexPsStatusEntry 1.3.6.1.4.1.1166.1.31.4.2.2.1
Power Supply Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexPsStatusEntry  

apexPsStatusPsNum 1.3.6.1.4.1.1166.1.31.4.2.2.1.1
PS Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

apexPsStatusInstalled 1.3.6.1.4.1.1166.1.31.4.2.2.1.2
This parameter indicates installed status of the PS.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notInstalled(1), installedAcInput(2), installedDcInput(3), fanModuleInstalled(4), unsupported(5)  

apexPsStatusOutputVoltage 1.3.6.1.4.1.1166.1.31.4.2.2.1.3
PS measured output voltage in milli-Volts.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexPsStatusOutputCurrent 1.3.6.1.4.1.1166.1.31.4.2.2.1.4
PS measured output current in milli-Amps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexPsStatusFanSpeed 1.3.6.1.4.1.1166.1.31.4.2.2.1.5
The fan speed in RPM an installed Power Supply or Fan Module. Zero if not installed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexPsStatusFanStatus 1.3.6.1.4.1.1166.1.31.4.2.2.1.6
PS Fan Status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexPsStatusTemperatureStatus 1.3.6.1.4.1.1166.1.31.4.2.2.1.7
Indicates whether the power supply is in protection mode due to an over temperature condition. The PS is shut down while in 'overTemp' and will recover when the temperature returns to normal operating range. A power cycle is not required for recovery. Note that Output Power Status will be 'error' when Temperature status is 'overTemp'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexPsStatusInputPowerStatus 1.3.6.1.4.1.1166.1.31.4.2.2.1.8
Indicates whether AC Input is within specification. Note that Output Power Status will be 'error' when Input Power status is 'error'
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexPsStatusOutputPowerStatus 1.3.6.1.4.1.1166.1.31.4.2.2.1.9
Indicates whether the +12V and +3.3V output power are within specification. If the output power error occurs with an Input Power error, apply input power to recover. If the output power error occurs with an Over Temperature error, a power cycle is not required for recovery. Otherwise, a power cycle is required for recovery. If the problem persists after the power cycle, the PS must be replaced for recovery.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexPsStatusErrorStatus 1.3.6.1.4.1.1166.1.31.4.2.2.1.10
Summary of errors reported on a power supply basis. The reported error will be the most severe.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), psNotInstalled(2), psUnsupported(3), inputPower(4), fanFault(5), overTemp(6), outputPower(7), commLost(8)  

apexPsStatusFaultCondition 1.3.6.1.4.1.1166.1.31.4.2.2.1.11
Current fault condition of the power supply errors.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexPsStatusDiagnosticData1 1.3.6.1.4.1.1166.1.31.4.2.2.1.12
Diagnostic data word 1 (HP) - Contents for Motorola diagnostic purposes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexPsStatusDiagnosticData2 1.3.6.1.4.1.1166.1.31.4.2.2.1.13
Diagnostic data word 2 (PS) - Contents for Motorola diagnostic purposes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexPsStatusCommError 1.3.6.1.4.1.1166.1.31.4.2.2.1.14
Communication with the Power Supply has failed and status cannot be determined. Only applies when valid PS installed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexPsStatusVersionsTable 1.3.6.1.4.1.1166.1.31.4.2.3
This is a table of version status parameters for the two Power Supplies.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexPsStatusVersionsEntry

apexPsStatusVersionsEntry 1.3.6.1.4.1.1166.1.31.4.2.3.1
Power Supply Version Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexPsStatusVersionsEntry  

apexPsStatusVersionsPsNum 1.3.6.1.4.1.1166.1.31.4.2.3.1.1
PS Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

apexPsStatusVersionsModel 1.3.6.1.4.1.1166.1.31.4.2.3.1.2
PS Model.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..17)  

apexPsStatusVersionsSerialNumber 1.3.6.1.4.1.1166.1.31.4.2.3.1.3
PS serial number.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexAsiMonitorPortOutputTsNum 1.3.6.1.4.1.1166.1.31.5.1.2.1
The number of the output transport stream to route to the ASI Monitor Port. Zero indicates that no stream is to be routed to the ASI Monitor port. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..48  

apexAsiMonitorPortEncryption 1.3.6.1.4.1.1166.1.31.5.1.2.2
Selects pre or post encryption for the ASI monitor port. This parameter is only applicable to APEXs with encryption capability. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER preEncryption(1), postEncryption(2)  

apexFastEnetDefaultGateway 1.3.6.1.4.1.1166.1.31.6.1.1.1
This is the IP address of the default gateway for the Fast Ethernet interfaces. This should be zero or a valid Class A, B, or C IP address. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexFastEnetRoutingApplyChange 1.3.6.1.4.1.1166.1.31.6.1.1.3
The Apply for the Fast Ethernet Static Routing Table. This parameter MUST be set to 'apply' in order for any of the data in the apexFastEnetRoutingTable to take effect. This parameter MUST be set LAST after all other data in the apexFastEnetRoutingTable has been configured. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexFastEnetRoutingTable 1.3.6.1.4.1.1166.1.31.6.1.2
This table is the configuration Static Routing table for the Fast Ethernet Interface. @Commit(param=apexFastEnetRoutingApplyChange, value=2) @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexFastEnetRoutingEntry

apexFastEnetRoutingEntry 1.3.6.1.4.1.1166.1.31.6.1.2.1
Fast Ethernet Interface Configuration Static Routing Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexFastEnetRoutingEntry  

apexFastEnetRoutingIndex 1.3.6.1.4.1.1166.1.31.6.1.2.1.1
The index of the Routing table entry. Currently limited to 16.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

apexFastEnetRoutingDestinIp 1.3.6.1.4.1.1166.1.31.6.1.2.1.2
The Fast Ethernet Routing Destination IP address. Once written, the change to this parameter will only take immediate effect after apexFastEnetRoutingApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexFastEnetRoutingGatewayIp 1.3.6.1.4.1.1166.1.31.6.1.2.1.3
The Fast Ethernet Routing Gateway IP address. Once written, the change to this parameter will only take immediate effect after apexFastEnetRoutingApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexFastEnetRoutingSubnetMask 1.3.6.1.4.1.1166.1.31.6.1.2.1.4
The Fast Ethernet Routing Subnet Mask. Once written, the change to this parameter will only take immediate effect after apexFastEnetRoutingApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexFastEnetInsertRateTable 1.3.6.1.4.1.1166.1.31.6.1.1.2
This is a table of configuration parameters for Output Transport Rate of Fast Ethernet MPEG data Insertion.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexFastEnetInsertRateEntry

apexFastEnetInsertRateEntry 1.3.6.1.4.1.1166.1.31.6.1.1.2.1
Output Transport Rate of Fast Ethernet MPEG Insertion Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexFastEnetInsertRateEntry  

apexFastEnetInsertRateOutputTsNum 1.3.6.1.4.1.1166.1.31.6.1.1.2.1.1
Output Transport Stream Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexFastEnetInsertRate 1.3.6.1.4.1.1166.1.31.6.1.1.2.1.2
Insertion Rate for the transport stream for Fast Ethernet MPEG data. Maximum MPEG data rate to insert data received via Fast Ethernet interfaces. Range is 0 Kbps to 2500 Kbps for each transport stream. Total for all transport streams must not exceed 10000 Kbps. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(min=0, max=2500) @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apexFastEnetMaxInputUdpPorts 1.3.6.1.4.1.1166.1.31.6.2.1.1
Maximum number of Fast Ethernet input UDP ports that can be opened on this APEX.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexFastEnetStatusPacketsTable 1.3.6.1.4.1.1166.1.31.6.2.2
Table of Fast Ethernet Insert Packet Statistics for each Fast Ethernet interface. Indexed by FE interface port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexFastEnetStatusPacketsEntry

apexFastEnetStatusPacketsEntry 1.3.6.1.4.1.1166.1.31.6.2.2.1
A row in the FE Insert Packets table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexFastEnetStatusPacketsEntry  

apexFastEnetPacketsPortNum 1.3.6.1.4.1.1166.1.31.6.2.2.1.1
Fast Ethernet interface port Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

apexFastEnetPacketsNumPkts 1.3.6.1.4.1.1166.1.31.6.2.2.1.2
Number of MPEG packets inserted during the last monitoring period (currently 5 seconds) on this FE interface port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexFastEnetPacketsTotPkts 1.3.6.1.4.1.1166.1.31.6.2.2.1.3
Total number of MPEG packets inserted on this FE interface port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexFastEnetPacketsNumDiscarded 1.3.6.1.4.1.1166.1.31.6.2.2.1.4
Number of MPEG packets discarded during the last monitoring period (currently 5 seconds) on this FE interface port. This may be due to a buffer overflow or incorrect configuration of the FE output stream insertion rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexFastEnetPacketsTotDiscarded 1.3.6.1.4.1.1166.1.31.6.2.2.1.5
Total number of FE MPEG packets discarded on this Output Transport Stream. Discarded packets on an FE interface port are those packets discarded due to an overflow condition.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexFastEnetInsertPacketsTable 1.3.6.1.4.1.1166.1.31.6.2.3
Table of Output Transport Stream FE Insert Packet Statistics. Indexed by Output Transport Stream number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexFastEnetInsertPacketsEntry

apexFastEnetInsertPacketsEntry 1.3.6.1.4.1.1166.1.31.6.2.3.1
A row in the Output Transport Stream FE Insert Packets table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexFastEnetInsertPacketsEntry  

apexFastEnetInsPacketsOutputTsNum 1.3.6.1.4.1.1166.1.31.6.2.3.1.1
Output Transport Stream Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexFastEnetInsPacketsNumPkts 1.3.6.1.4.1.1166.1.31.6.2.3.1.2
Number of MPEG packets inserted during the last monitoring period (currently 5 seconds) on this Output Transport Stream.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexFastEnetInsPacketsTotPkts 1.3.6.1.4.1.1166.1.31.6.2.3.1.3
Total number of MPEG packets inserted on this Output Transport Stream.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexFastEnetInsPacketsNumDiscarded 1.3.6.1.4.1.1166.1.31.6.2.3.1.4
Number of MPEG packets discarded during the last monitoring period (currently 5 seconds) on this Output Transport Stream. This may be due to a buffer overflow or incorrect configuration of the FE output stream insertion rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexFastEnetInsPacketsTotDiscarded 1.3.6.1.4.1.1166.1.31.6.2.3.1.5
Total number of FE MPEG packets discarded on this Output Transport Stream. Discarded packets on an output stream are those packets discarded due to an overflow condition.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOampIpAddr 1.3.6.1.4.1.1166.1.31.6.3.1.1.1
This is the IP address of the OAMP IP (Enet1) interface of the APEX. This IP address is set via a BootP when connected to a Bootp server. When not connected to a BootP server, the IP address may directly be changed by setting this parameter. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexOampSubnetMask 1.3.6.1.4.1.1166.1.31.6.3.1.1.2
This is subnet mask of the OAMP IP (Enet1) interface of the APEX. The subnet mask is normally via a BootP when connected to a BootP server. When not connected to a Bootp Server, the Subnet Mask may directly be changed by setting this parameter. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexOampAutoNegotiate 1.3.6.1.4.1.1166.1.31.6.3.1.1.3
OAMP IP (Enet1) Ethernet Auto-Negotiation setting. 'disabled' is not supported. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexOampMacAddr 1.3.6.1.4.1.1166.1.31.6.3.2.1.1
This is the MAC address of the APEX OAMP IP (Enet1) Interface. It is set at the factory and cannot be changed. The string length is 17 characters in the format 'hh:hh:hh:hh:hh:hh' where 'hh' is a hexadecimal number.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..17)  

apexOampSpeed 1.3.6.1.4.1.1166.1.31.6.3.2.1.2
OAMP IP (Enet1) Ethernet speed (10Mbps or 100Mbps). This is determined by the results of the auto-negotiation process. If auto-negotiation fails, the default speed is 100Mbps.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), interfaceSpeed10Mbps(1), interfaceSpeed100Mbps(2)  

apexOampDuplexMode 1.3.6.1.4.1.1166.1.31.6.3.2.1.3
OAMP IP (Enet1) Ethernet Duplex Mode (full or half) This is determined by the results of the auto-negotiation process. If auto-negotiation fails, the default mode is Full.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), halfDuplex(1), fullDuplex(2)  

apexOampInputTsAssignedCount 1.3.6.1.4.1.1166.1.31.6.3.2.1.4
Number of input transport streams assigned to the OAMP IP interface (Enet1).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOampLinkActive 1.3.6.1.4.1.1166.1.31.6.3.2.1.5
This indicates if the OAMP (ENET1) link is active.
Status: current Access: read-only
OBJECT-TYPE    
  ActiveTYPE  

apexDataIpAddr 1.3.6.1.4.1.1166.1.31.6.4.1.1.1
This is the IP address of the Data IP (Enet2) interface of this APEX. The data IP address may directly be changed by setting this parameter. The Data IP address must be configured such that the Data IP interface and the OAMP interface are on different networks. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexDataIpSubnetMask 1.3.6.1.4.1.1166.1.31.6.4.1.1.2
This is subnet mask of the Data IP (Enet2) interface of this APEX. The data IP Subnet Mask may directly be changed by setting this parameter. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexDataIpAutoNegotiate 1.3.6.1.4.1.1166.1.31.6.4.1.1.3
Data IP (Enet2) Ethernet Auto-Negotiation setting. 'disabled' is not supported. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexDataIpMacAddr 1.3.6.1.4.1.1166.1.31.6.4.2.1.1
This is the MAC address of the APEX Data IP (Enet2) Interface. It is set at the factory and cannot be changed. The string length is 17 characters in the format 'hh:hh:hh:hh:hh:hh' where 'hh' is a hexadecimal number.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..17)  

apexDataIpSpeed 1.3.6.1.4.1.1166.1.31.6.4.2.1.2
Data IP (Enet2) Ethernet speed (10Mbps or 100Mbps). This is determined by the results of the auto-negotiation process. If auto-negotiation fails, the default speed is 100Mbps. This status item is only valid when the Data IP port is enabled and properly configured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), interfaceSpeed10Mbps(1), interfaceSpeed100Mbps(2)  

apexDataIpDuplexMode 1.3.6.1.4.1.1166.1.31.6.4.2.1.3
Data IP (Enet2) Ethernet Duplex Mode (full or half) This is determined by the results of the auto-negotiation process. If auto-negotiation fails, the default mode is Full. This status item is only valid when the Data IP port is enabled and properly configured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), halfDuplex(1), fullDuplex(2)  

apexDataIpInputTsAssignedCount 1.3.6.1.4.1.1166.1.31.6.4.2.1.4
Number of input transport streams assigned to the Data IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDataIpAddrInUse 1.3.6.1.4.1.1166.1.31.6.4.2.1.5
Indicates the IP Address currently being used by the Data IP port (Enet2). This parameter will be either apexDataIpAddr or an APEX selected IP address. Refer to apexDataIpInUseReason for more information.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexDataIpSubnetMaskInUse 1.3.6.1.4.1.1166.1.31.6.4.2.1.6
Indicates the Subnet Mask currently being used by the Data IP port (Enet2). This parameter will be either apexDataIpSubnetMask or an APEX selected mask. Refer to apexDataIpInUseReason for more information.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexDataIpInUseReason 1.3.6.1.4.1.1166.1.31.6.4.2.1.7
Reason for apexDataIpAddrInUse and apexDataIpSubnetMaskInUse Data IP (Enet2) parameters. 'notApplicable' - Enet2 not configured by user or for REM connection. 'userConfig' - APEX is not overriding user configured parameters. 'directRemConnection' - The DATA IP port (Enet2) is in use for QAM RF Redundancy so the APEX has overridden the user configured parameters.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), userConfig(1), directRemConnection(2)  

apexDataIpLinkActive 1.3.6.1.4.1.1166.1.31.6.4.2.1.8
This indicates if the DataIP (ENET2) link is active.
Status: current Access: read-only
OBJECT-TYPE    
  ActiveTYPE  

apexGbeDefaultGateway1 1.3.6.1.4.1.1166.1.31.7.1.1.1
This is the IP address of the default gateway for Gigabit Ethernet interfaces 1 and 2. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexGbeDefaultGateway2 1.3.6.1.4.1.1166.1.31.7.1.1.2
This is the IP address of the default gateway for Gigabit Ethernet interfaces 3 and 4. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexGbeJitterAbsorption 1.3.6.1.4.1.1166.1.31.7.1.1.3
This object is obsolete. Jitter Absorption setting in range of 0 to 200 milliseconds in increments of 5 ms. A change to this parameter will cause the Gigabit Ethernet processor to reset all of its internal Ethernet frame buffers. This will result in a momentary loss of data causing a minor glitch on all output streams. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(step=5) @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32 0..200  

apexGbeGarpPeriodicity 1.3.6.1.4.1.1166.1.31.7.1.1.4
Gratuitous ARP period in range of 20 to 300 seconds. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 20..300  

apexGbeConfigTableApplyChange 1.3.6.1.4.1.1166.1.31.7.1.1.5
The Apply for the Gigabit Ethernet Configuration Table. This parameter MUST be set to 'apply' in order for any of the data in the apexGbeConfigTable to take effect. This parameter MUST be set LAST after all other data in the apexGbeConfigTable has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexGbeNominalBufferLevel 1.3.6.1.4.1.1166.1.31.7.1.1.6
Gigabit Ethernet Nominal Buffer Level. Range of 50 to 475 milliseconds in increments of 5 ms. A change to this parameter will cause the Gigabit Ethernet processor to reset all of its internal Ethernet frame buffers. This will result in a momentary loss of data causing a minor glitch on all output streams. The buffer level is the normal standard starting level for an input stream buffer. It is highly recommended that this level not be changed from its default setting. The buffer level needs to be set at an appropriate amount to allow for network jitter, clock skew between the APEX and input source, and for maximum time between PCRs (100ms). In addition, the level must not be set too high as the buffer needs to be able to grow as packets are received and PCR processing is applied. This buffer level is the initial level the APEX will attempt to maintain at all times. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 50..475  

apexGbeInputDataTsSmoothingPeriod 1.3.6.1.4.1.1166.1.31.7.1.1.7
Input Data stream smoothing period. Amount of time in milliseconds over which the GigE will smooth out input streams that do not contain PCRs. This allows the GigE to play out the input streams with the packets equally spaced out over this period. This helps to reduce network jitter and bursts of data to the output. The smoothing period is used in conjunction with the data stream buffer depth to perform this smoothing algorithm. The smoothing period must be equal to or less than the data stream buffer depth. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 250..650  

apexGbeInputDataTsBufferDepth 1.3.6.1.4.1.1166.1.31.7.1.1.8
GBE Input Data stream buffer depth. Amount of time in milliseconds that the GigE will buffer input streams that do not contain PCRs. This allows the GigE to buffer these streams to remove network jitter and then play them out with the packets equally spaced out. The buffer depth must be equal to or greater than the data stream smoothing period. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 250..650  

apexGbeConfigInputDataTsApplyText 1.3.6.1.4.1.1166.1.31.7.1.1.9
When apexGbeConfigInputDataTsApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexGbeConfInputUnicastTimeout 1.3.6.1.4.1.1166.1.31.7.1.1.10
Loss of input stream timeout value (in milliseconds) for unicast inputs. This determines the amount of time a unicast input stream is missing before the APEX will declare the input stream lost. Loss of input is used for determining all SDV failover conditions. It is also used for Manual Routing failover conditions when using hot/warm transport stream redundancy. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(step=200) @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 600..6000  

apexGbeConfInputMulticastTimeout 1.3.6.1.4.1.1166.1.31.7.1.1.11
Loss of input stream timeout value (in milliseconds) for multicast inputs. This determines the amount of time a unicast input stream is missing before the APEX will declare the input stream lost. Loss of input is used for determining all SDV failover conditions. It is also used for Manual Routing failover conditions when using hot/warm transport stream redundancy. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(step=200) @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 600..6000  

apexGbeConfLossOfInputTsType 1.3.6.1.4.1.1166.1.31.7.1.1.12
Loss of input stream type. Determines if detection of loss of an input stream is based on data rate or stream rate. Data rate includes only non-null MPEG packets (such as video and audio packets). Stream rate includes all packets, including null packets. The loss of an input stream uses the timeout value for the specific input (unicast or multicast) and the input type. If no packets are received within the specified timeout value, taking into account the loss of input type checking, then the input stream is determined to be missing. Data rate should be used for detecting loss of input when the input stream is normally null filled. When a user requires notification of a loss of input stream when there is no content streamed, data rate should be selected. Stream rate should be used for detecting loss of input stream when the user requires to be notified when there is no input stream at all being received. Loss of input is used for determining all SDV failover conditions. It is also used for Manual Routing failover conditions when using hot/warm transport stream redundancy. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  RateComparisonTYPE  

apexGbeConfigTable 1.3.6.1.4.1.1166.1.31.7.1.2
This is a table of configuration parameters for the Gigabit Ethernet Interfaces. Once written, the change to this table will only take immediate effect after apexGbeConfigTableApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexGbeConfigTableApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeConfigEntry

apexGbeConfigEntry 1.3.6.1.4.1.1166.1.31.7.1.2.1
Gigabit Ethernet Interface Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeConfigEntry  

apexGbeConfigInterfaceNum 1.3.6.1.4.1.1166.1.31.7.1.2.1.1
Gigabit Ethernet Interface Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexGbeConfigEnable 1.3.6.1.4.1.1166.1.31.7.1.2.1.2
This parameter enables the Gigabit Ethernet Interface.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexGbeConfigIpAddr 1.3.6.1.4.1.1166.1.31.7.1.2.1.3
This is the IP address of this Gigabit Ethernet interface. It is recommended that each Gigabit Ethernet interface be on a different subnet. Each must be given a unique IP address. 0.0.0.0 indicates the interface is not in use.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexGbeConfigIpSubnetMask 1.3.6.1.4.1.1166.1.31.7.1.2.1.4
This is subnet mask of this Gigabit Ethernet interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexGbeConfigAutoNegotiate 1.3.6.1.4.1.1166.1.31.7.1.2.1.5
Auto negotiation enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexGbeConfigFrameBufferTable 1.3.6.1.4.1.1166.1.31.7.1.3
This is a table of configuration parameters related to Gigabit Ethernet Frame Buffer statistics gathering. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeConfigFrameBufferEntry

apexGbeConfigFrameBufferEntry 1.3.6.1.4.1.1166.1.31.7.1.3.1
Gigabit Ethernet Frame Buffer Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeConfigFrameBufferEntry  

apexGbeConfigFrameBufferProcessorNum 1.3.6.1.4.1.1166.1.31.7.1.3.1.1
Gigabit Ethernet Processor Number. Proc 1 = GBE Interfaces 1 and 2 Proc 2 = GBE Interfaces 3 and 4
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

apexGbeConfigFrameBufferMaxInDataRate 1.3.6.1.4.1.1166.1.31.7.1.3.1.2
Maximum Gigabit Ethernet MPEG input data rate in bps. This is the total amount of MPEG data expected to be received by Gigabit Ethernet frame interfaces on the processor. This data rate is used to determine the frame buffer reset limit. The expected data rate should always be set equal to or greater than the actual input data rate. The value of apexGbeJitterAbsorption can limit the valid range of this data rate. It is highly recommended that the user consult with Motorola prior to changing the expected data rate.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1000000..2000000000  

apexGbeConfigFrameBufferAlarmThreshold 1.3.6.1.4.1.1166.1.31.7.1.3.1.3
User defined threshold representing a percentage of frame buffer depth. The frame buffer level is monitored by the APEX and the maximum level is based on the actual input data rate. The threshold percentage is used to determine when to issue a Gigabit Ethernet Frame Buffer Fullness alarm (apexAlarmGbeBufferFullness).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..100  

apexGbeConfInRedundMonitorPeriod 1.3.6.1.4.1.1166.1.31.7.1.4.1.1
This is the time in seconds over which Redundant Gigabit Ethernet Input Transport Stream Pairs will be monitored. Range is 1 to 30 seconds. Primary to Secondary Fail Over - The monitored data rate of the Primary must be below the Secondary by apexManRteGbeInRedThreshold (for Manual Routing) percent for apexGbeConfInRedundMonitorPeriod before fail over to Secondary will occur. Fail over to Secondary will not occur if fail over is suspended for the Primary. Secondary to Primary Switch Back - The monitored data rate of the Primary must have returned above apexManRteGbeInRedThreshold (for Manual Routing) percent below the Secondary for apexGbeConfInRedundMonitorPeriod before switch back to Primary will occur. Switch back to Primary will not occur if fail over is suspended for the Secondary. Once the Primary is restored, switch back to Primary will be delayed by apexGbeConfInRedundSwitchTime when apexGbeConfInRedundAutoSwitchBack is 'enabled'. Note that if apexGbeConfInRedundAutoSwitchBack is 'disabled' switch back will not occur. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..30  

apexGbeConfInRedundSwitchTime 1.3.6.1.4.1.1166.1.31.7.1.4.1.2
This is the time in seconds to wait before switching back to the Primary of a Redundant Gigabit Ethernet Input TS pair after the Primary is healthy. Range is 0 to 3600. This time is in addition to apexGbeConfInRedundMonitorPeriod. Switch back to Primary will not occur if fail over is suspended for the Secondary. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..3600  

apexGbeConfInRedundAutoSwitchBack 1.3.6.1.4.1.1166.1.31.7.1.4.1.3
This is the enable/disable of automatic switch back from Secondary to Primary for Gigabit Ethernet redundancy. When 'enabled', switch back to the Primary will automatically occur when the Primary is restored. When 'disabled', the user must force back to the Primary using apexGbeConfInRedundForceToPrimary or apexManRteGbeInRedForceSwitch. This parameter applies to all configured redundant pairs. Auto switch back to the primary will not occur if the user forced a failover to the secondary. Auto switch back only occurs after a non-forced failover event. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexGbeConfInRedundForceToSecondary 1.3.6.1.4.1.1166.1.31.7.1.4.1.4
The Gigabit Ethernet Redundant Pair force switch any pair that is currently on the Primary to the Secondary. This will have no effect if the corresponding row setting of apexManRteGbeInRedEnable is 'disabled'. This will only have an effect when the Primary is the In-Use Input TS of a Redundant Pair (apexInputTsStatPriState or apexInputTsStatSecState is 'openedInUse'). Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER switchNotInProgress(1), forceSwitch(2)  

apexGbeConfInRedundForceToPrimary 1.3.6.1.4.1.1166.1.31.7.1.4.1.5
The Gigabit Ethernet Redundant Pair force switch any pair that is currently on the Secondary to the Primary. This will have no effect if the corresponding row setting of apexManRteGbeInRedEnable is 'disabled'. This will only have an effect when the Secondary is the In-Use Input TS of a Redundant Pair (apexInputTsStatPriState or apexInputTsStatSecState is 'openedInUse'). Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER switchNotInProgress(1), forceSwitch(2)  

apexGbeConfInRedundManualRouteRedundType 1.3.6.1.4.1.1166.1.31.7.1.4.1.6
The redundancy type for output streams in Manual Routing operating mode. - hotWarm indicates only 1 input stream, primary or secondary, is open at any one time. For multicast streams, primary will be joined initially. The secondary is joined after a failover (the primary will be dropped prior to joining the secondary). When falling back to the primary, the secondary is dropped (closed), then the primary is joined (opened). - hotHot indicates both the primary and secondary streams are opened at the same time. For multicast streams, both streams are joined immediately. Changes to the redundancy type cannot be made while there are active routes. All routes must be deleted prior to changing the redundancy type. Once written, a save must be performed via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER hotWarm(1), hotHot(2)  

apexGbeConfigInputDataTsTable 1.3.6.1.4.1.1166.1.31.7.1.5
Table of data for GBE input data stream identification. Each entry in this table identifies a Gigabit Ethernet input stream that is a data stream only. Data streams are streams without PCR. These streams require special processing to avoid overflowing the output. There are 128 rows in this table. Once written, the change to this table will only take immediate effect after apexGbeConfigInputDataTsApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexGbeConfigInputDataTsApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeConfigInputDataTsEntry

apexGbeConfigInputDataTsEntry 1.3.6.1.4.1.1166.1.31.7.1.5.1
GBE Input Data Stream Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeConfigInputDataTsEntry  

apexGbeConfigInputDataTsIndex 1.3.6.1.4.1.1166.1.31.7.1.5.1.1
Index of GBE Input Data Stream Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexGbeConfigInputDataTsEnable 1.3.6.1.4.1.1166.1.31.7.1.5.1.2
Indicates whether this GBE Input Data Stream entry is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexGbeConfigInputDataTsInterface 1.3.6.1.4.1.1166.1.31.7.1.5.1.3
Number of the input interface (Port number). Range: '0' = Not Applicable GBE = 1-4
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4  

apexGbeConfigInputDataTsUdp 1.3.6.1.4.1.1166.1.31.7.1.5.1.4
GBE Input UDP Port. Range: 0-65535
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexGbeConfigInputDataTsMulticastIp 1.3.6.1.4.1.1166.1.31.7.1.5.1.5
The Multicast receive IP address. An IP address of 0.0.0.0 indicates singlecast only. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexGbeConfigInputDataTsSourceIp 1.3.6.1.4.1.1166.1.31.7.1.5.1.6
This is the IP address of the source device. This field is only used when a multicast IP address is also specified.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexGbeConfigInputDataTsApplyTable 1.3.6.1.4.1.1166.1.31.7.1.6
Table of Apply Change for the GBE Input Data Stream Table. A row in this table corresponds to the same row index in the GBE Input Data Stream table (apexGbeConfigInputDataTsTable).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeConfigInputDataTsApplyEntry

apexGbeConfigInputDataTsApplyEntry 1.3.6.1.4.1.1166.1.31.7.1.6.1
GBE Input Data Stream Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeConfigInputDataTsApplyEntry  

apexGbeConfigInputDataTsApplyIndex 1.3.6.1.4.1.1166.1.31.7.1.6.1.1
The index of the GBE Input Data Stream Apply Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexGbeConfigInputDataTsApplyChange 1.3.6.1.4.1.1166.1.31.7.1.6.1.2
The Apply for the row of data in the GBE Input Data Stream Table. A row in this table corresponds to the same row index in the GBE Input Data Stream table. This parameter MUST be set to 'apply' in order for any of the data in the GBE Input Data Stream Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the GBE Input Data Stream Table row has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexGbeConfIfRedundAutoSwitchBackEnable 1.3.6.1.4.1.1166.1.31.7.1.7.1.1
Enables the ability for the secondary interface to switch back when link is re-detected on the primary interface. Auto switch back to the primary interface will not occur if the user forced a failover to the secondary. Auto switch back only occurs after a non-forced failover. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexGbeConfIfRedundAutoSwitchBackPeriod 1.3.6.1.4.1.1166.1.31.7.1.7.1.2
Timer for determining that the primary interface is OK for auto- switchback. The primary interface must have link for the configured amount of time. Valid time is 1-30 seconds. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..30  

apexGbeConfigInterfaceRedundancyTable 1.3.6.1.4.1.1166.1.31.7.1.7.2
This is a table of configuration parameters for GbE Interface Redundancy.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeConfigInterfaceRedundancyEntry

apexGbeConfigInterfaceRedundancyEntry 1.3.6.1.4.1.1166.1.31.7.1.7.2.1
GbE Interface Redundancy Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeConfigInterfaceRedundancyEntry  

apexGbeConfIfRedundIndex 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.1
GbE Interface Pair number. Value of 1 is GbE1 and GbE2 pair. Value of 2 is GbE3 and GbE4 pair.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

apexGbeConfIfRedundEnable 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.2
Enables GbE Interface Redundancy for ports pair. Failover is based on link status. If the primary GbE fails, the secondary GbE will become active and will start receiving content. There is no data rate comparison, as only one interface in the redundancy pair is active. The secondary GbE cannot be in use prior to enabling redundancy. TS redundancy may not be used at the same time as interface redundancy. Interface redundancy is not applicable when chassis redundancy is enabled. Once written, the change to this table will only take immediate effect after apexGbeConfIfRedundApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexGbeConfIfRedundApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexGbeConfIfRedundForceFailover 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.3
When set to failover(2), this results in the APEX switching to the interface that is currently not in use. If the primary GbE is in use and this is set to failover(2) mappings will be then routed to the secondary GbE. If the secondary GbE is in use and this is set to failover(2) mappings will then be routed back to the primary GbE. Once written, the change to this table will take immediate @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER failoverNotInProgress(1), failover(2)  

apexGbeConfIfRedundSuspendFailover 1.3.6.1.4.1.1166.1.31.7.1.7.2.1.4
Enables and disables suspending of Interface failover. Prevents failovers to or from backup. Force failover (apexGbeConfIfRedundForceFailover) overrides this setting. Once written, the change to this table will only take immediate effect after apexGbeConfIfRedundApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexGbeConfIfRedundApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexGbeConfigInterfaceRedundancyApplyTable 1.3.6.1.4.1.1166.1.31.7.1.7.3
Table of Apply Change for the GBE Interface Redundancy Configuration Table. A row in this table corresponds to the same row index in the GBE Config Interface Redundancy table (apexGbeConfigInterfaceRedundancyTable).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeConfigInterfaceRedundancyApplyEntry

apexGbeConfigInterfaceRedundancyApplyEntry 1.3.6.1.4.1.1166.1.31.7.1.7.3.1
GBE Config Interface Redundancy Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeConfigInterfaceRedundancyApplyEntry  

apexGbeConfIfRedundApplyIndex 1.3.6.1.4.1.1166.1.31.7.1.7.3.1.1
The index of the GBE Config Interface Redundancy Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

apexGbeConfIfRedundApplyChange 1.3.6.1.4.1.1166.1.31.7.1.7.3.1.2
The Apply for the row of data in the GBE Config Interface Redundancy Table. A row in this table corresponds to the same row index in the GBE Config Interface Redundancy table. This parameter MUST be set to 'apply' in order for any of the data in the GBE Input Data Stream Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the GBE Input Data Stream Table row has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexGbeBootCodeVersion 1.3.6.1.4.1.1166.1.31.7.2.1.1
APEX Gigabit Ethernet Processor Boot Code Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexGbeApplicationCodeVersion 1.3.6.1.4.1.1166.1.31.7.2.1.2
APEX Gigabit Ethernet Processor Application Code Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexGbeMaxInputTs 1.3.6.1.4.1.1166.1.31.7.2.1.3
Maximum number of Gigabit Ethernet input transport streams that can be opened on this APEX. This is the maximum across all installed GigE interfaces. One GigE interface can use all Input TS.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeRoutedPacketUpdateInterval 1.3.6.1.4.1.1166.1.31.7.2.1.4
Time in seconds between Gigabit Ethernet Routed Packet Count updates. The count during this time is defined as one sample. This time applies to packet counts contained in apexGbeStatusRoutedPacketTable. To compute rate from packet count for the last update interval: Rate(bps) = (Packet_Count * 188 bytes/packet * 8 bits/byte) / Update_Interval This value is set by the APEX at startup and is constant.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeStatusTable 1.3.6.1.4.1.1166.1.31.7.2.2
This is a table of status parameters for the Gigabit Ethernet Interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeStatusEntry

apexGbeStatusEntry 1.3.6.1.4.1.1166.1.31.7.2.2.1
Gigabit Ethernet Interface Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeStatusEntry  

apexGbeStatusGbeInterfaceNum 1.3.6.1.4.1.1166.1.31.7.2.2.1.1
Gigabit Ethernet Interface Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexGbeStatusMacAddr 1.3.6.1.4.1.1166.1.31.7.2.2.1.2
This is the MAC address of the Gigabit Ethernet Interface. It is set at the factory and cannot be changed. The string length is 17 characters in the format 'hh:hh:hh:hh:hh:hh' where 'hh' is a hexadecimal number.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..17)  

apexGbeStatusLinkActive 1.3.6.1.4.1.1166.1.31.7.2.2.1.3
This indicates if the Gigabit Ethernet optical link is active.
Status: current Access: read-only
OBJECT-TYPE    
  ActiveTYPE  

apexGbeStatusIgmpVersion 1.3.6.1.4.1.1166.1.31.7.2.2.1.4
This indicates the IGMP Version being used on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), igmpV1(1), igmpV2(2), igmpV3(3)  

apexGbeStatusLossOfPhysicalInput 1.3.6.1.4.1.1166.1.31.7.2.2.1.5
The current severity of apexAlarmGbeLossOfPhysicalInput for this interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexGbeInputTsAssignedTable 1.3.6.1.4.1.1166.1.31.7.2.3
Table of Gigabit Ethernet Input TS Assigned data.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeInputTsAssignedEntry

apexGbeInputTsAssignedEntry 1.3.6.1.4.1.1166.1.31.7.2.3.1
Gigabit Ethernet Interface Input TS Assigned Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeInputTsAssignedEntry  

apexGbeInputTsAssignedGbeInterfaceNum 1.3.6.1.4.1.1166.1.31.7.2.3.1.1
The index of the Gigabit Ethernet Input TS Assigned Table. Represents the Gigabit Ethernet interface number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexGbeInputTsAssignedCount 1.3.6.1.4.1.1166.1.31.7.2.3.1.2
Number of input transport streams assigned to the GigE interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeOpenInputUdpPortTable 1.3.6.1.4.1.1166.1.31.7.2.4
Table of Gigabit Ethernet Input Open UDP Port data.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeOpenInputUdpPortEntry

apexGbeOpenInputUdpPortEntry 1.3.6.1.4.1.1166.1.31.7.2.4.1
Gigabit Ethernet Interface Input Open UDP Port Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeOpenInputUdpPortEntry  

apexGbeOpenInputUdpPortGbeInterfaceNum 1.3.6.1.4.1.1166.1.31.7.2.4.1.1
The index of the Gigabit Ethernet Input Open UDP Port Table. Represents the Gigabit Ethernet interface number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexGbeOpenInputUdpPortCount 1.3.6.1.4.1.1166.1.31.7.2.4.1.2
Number of open Input UDP Ports on the GigE interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatusRoutedPacketTable 1.3.6.1.4.1.1166.1.31.7.2.5
This table contains Gigabit Ethernet MPEG packet counts for each Output Transport Stream of this APEX. Update interval is apexGbeRoutedPacketUpdateInterval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeStatusRoutedPacketEntry

apexGbeStatusRoutedPacketEntry 1.3.6.1.4.1.1166.1.31.7.2.5.1
Gigabit Ethernet Interface Status Routed Packet Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeStatusRoutedPacketEntry  

apexGbeStatusRoutedPacketOutputTsNum 1.3.6.1.4.1.1166.1.31.7.2.5.1.1
The index of the Gigabit Ethernet Routed Packet Status Table. Represents Output Transport Stream number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexGbeStatusTotRoutedPackets 1.3.6.1.4.1.1166.1.31.7.2.5.1.2
Total number of Gigabit Ethernet MPEG packets routed to this Output Transport Stream.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatusNumRoutedPackets 1.3.6.1.4.1.1166.1.31.7.2.5.1.3
Number of Gigabit Ethernet MPEG packets routed to this Output Transport Stream during the last monitoring period (apexGbeRoutedPacketUpdateInterval).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatusFrameCounterTableResetAll 1.3.6.1.4.1.1166.1.31.7.2.6.1.1
Reset Ethernet Frame Counter Totals for all GigE interfaces: - apexGbeTotalRxSinglecastFrames - apexGbeTotalRxMulticastFrames - apexGbeTotalRxBroadcastFrames - apexGbeTotalRxErrorFrames - apexGbeTotalRxFrames - apexGbeTotalTxGoodFrames - apexGbeTotalTxErrorFrames Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ResetStatisticsTYPE  

apexGbeFrameCounterUpdateInterval 1.3.6.1.4.1.1166.1.31.7.2.6.1.2
Time in seconds between Gigabit Ethernet Frame Counter updates. The count during this time is defined as one sample. This time applies to packet counts contained in apexGbeStatusFrameCounterTable. To compute rate from frame count for the last update interval: Rate(bps) = (Frame_Count * 7 packets/frame 188 bytes/packet * 8 bits/byte) / Update_Interval This value is set by the APEX at startup and is constant.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeStatusFrameCounterTable 1.3.6.1.4.1.1166.1.31.7.2.6.2
Table of Gigabit Ethernet Frame Counter Statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeStatusFrameCounterEntry

apexGbeStatusFrameCounterEntry 1.3.6.1.4.1.1166.1.31.7.2.6.2.1
Gigabit Ethernet Interface Frame Counter Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeStatusFrameCounterEntry  

apexGbeFrameCounterGbeInterfaceNum 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.1
The index of the Gigabit Ethernet Frame Counter Table. Represents the Gigabit Ethernet interface number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexGbeFrameCounterReset 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.2
Reset Ethernet Frame Counter Statistics totals for a single GigE interface: - apexGbeTotalRxSinglecastFrames - apexGbeTotalRxMulticastFrames - apexGbeTotalRxBroadcastFrames - apexGbeTotalRxErrorFrames - apexGbeTotalRxFrames - apexGbeTotalTxGoodFrames - apexGbeTotalTxErrorFrames Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ResetStatisticsTYPE  

apexGbeTotalRxSinglecastFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.3
Total number of singlecast Ethernet frames received since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeTotalRxMulticastFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.4
Total number of multicast Ethernet frames received since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeTotalRxBroadcastFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.5
Total number of broadcast Ethernet frames received since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeTotalRxErrorFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.6
Total number of bad Ethernet frames received since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeTotalRxFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.7
Total number of Ethernet frames received since last reset. This is the sum of apexGbeTotalRxSinglecastFrames, apexGbeTotalRxMulticastFrames, apexGbeTotalRxBroadcastFrames, and apexGbeTotalRxErrorFrames. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeRxSinglecastFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.8
Number of singlecast Ethernet frames received during last status checking interval. Status checking interval is apexGbeFrameCounterUpdateInterval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeRxMulticastFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.9
Number of multicast Ethernet frames received during last status checking interval. Status checking interval is apexGbeFrameCounterUpdateInterval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeRxBroadcastFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.10
Number of broadcast Ethernet frames received during last status checking interval. Status checking interval is apexGbeFrameCounterUpdateInterval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeRxErrorFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.11
Number of bad Ethernet frames received during last status checking interval. Status checking interval is apexGbeFrameCounterUpdateInterval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeRxFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.12
Number of Ethernet frames received during last status checking interval. This is the sum of apexGbeRxSinglecastFrames, apexGbeRxMulticastFrames, apexGbeRxBroadcastFrames, and apexGbeRxErrorFrames. Status checking interval is five seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeTotalTxGoodFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.13
Total number of good Ethernet frames (singlecast, multicast, and broadcast) transmitted since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeTotalTxErrorFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.14
Total number of bad Ethernet frames transmitted since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeTxGoodFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.15
Number of good Ethernet frames (singlecast, multicast, and broadcast) transmitted during last status checking interval. Status checking interval is five seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeTxErrorFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.16
Number of bad Ethernet frames transmitted during last status checking interval. Status checking interval is five seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeRxDocsisFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.17
Number of good Ethernet frames containing DOCSIS (singlecast, multicast, and broadcast) received during last status checking interval. Status checking interval is five seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeTotalRxDocsisFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.18
Total number of good Ethernet frames containing DOCSIS(singlecast, multicast, and broadcast) received since last reset. Reset using apexGbeStatusFrameCounterTableResetAll or apexGbeFrameCounterReset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeRxMpegDocsisFrames 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.19
Number of MPEG packets generated from DOCSIS data (singlecast, multicast, and broadcast) received during last status checking interval. Status checking interval is five seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeIpFragmentedPkts 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.20
Number of IP fragmented packets received during last status checking interval. Status checking interval is five seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeTotalIpFragmentedPkts 1.3.6.1.4.1.1166.1.31.7.2.6.2.1.21
Total number of IP fragmented packets received during last status checking interval. Status checking interval is five seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeFrameBufferStatsTable 1.3.6.1.4.1.1166.1.31.7.2.7.2
Table of Gigabit Ethernet Frame Buffer Statistics for each GBE processor.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeFrameBufferStatsEntry

apexGbeFrameBufferStatsEntry 1.3.6.1.4.1.1166.1.31.7.2.7.2.1
Gigabit Ethernet Frame Buffer Statistics Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeFrameBufferStatsEntry  

apexGbeFrameBufferProcessorNum 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.1
Index of the Gigabit Ethernet Buffer Statistics Table. Gigabit Ethernet Processor Number. Proc 1 = GBE Interfaces 1 and 2 Proc 2 = GBE Interfaces 3 and 4
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

apexGbeFrameBufferResetLevelLimit 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.2
The point at which the GigE frame buffer will be reset, in milliseconds. This value is equal to (maximum buffer depth - 5). The maximum buffer depth is calculated based on the expected input data rate (apexGbeConfigFrameBufferMaxInDataRate).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeFrameBufferCurrMsLevel 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.3
Current highest Gigabit Ethernet Frame Buffer level in milliseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeFrameBufferCurrPercentFull 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.4
Current highest Gigabit Ethernet Frame Buffer fullness as a percentage of the buffer depth available for a given aggregate rate. This percentage is calculated using the current buffer level (apexGbeFrameBufferCurrMsLevel) and the actual input data rate.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeFrameBufferUnderflowLevel 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.5
The point at which the GigE frame buffer will underflow, in milliseconds. This value is calculated based on the sum of the number of received frames per second for all interfaces.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeFrameBufferOverflowLevel 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.6
The point at which the GigE frame buffer will overflow, in milliseconds. This value is calculated based on the sum of the number of received frames per second for all interfaces.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeFrameBufferAlarmStatus 1.3.6.1.4.1.1166.1.31.7.2.7.2.1.7
The current highest severity of apexAlarmGbeBufferFullness for the GBE Processor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexGbeFrameBufferHourlyTable 1.3.6.1.4.1.1166.1.31.7.2.7.3
Table of Gigabit Ethernet Frame Buffer Statistics. There can be up to 24 entries in the table for each GBE Processor. Each entry represents one hour. The newest entry is placed at the beginning of the table and, if necessary, the oldest entry is pushed off the end of the table. The table will not be full until 24 hours have passed.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeFrameBufferHourlyEntry

apexGbeFrameBufferHourlyEntry 1.3.6.1.4.1.1166.1.31.7.2.7.3.1
Gigabit Ethernet Interface Frame Buffer Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeFrameBufferHourlyEntry  

apexGbeFrameBufferHourlyProcessorNum 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.1
First index of the Gigabit Ethernet Buffer Status Table. Gigabit Ethernet Processor Number. Proc 1 = GBE Interfaces 1 and 2 Proc 2 = GBE Interfaces 3 and 4
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

apexGbeFrameBufferHourlyIndex 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.2
Second index of the Gigabit Ethernet Buffer Status Table. Each index represents one hour. There can be up to 24 entries in the table. The most recent entry is always at the beginning of the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..24  

apexGbeFrameBufferHourlyInInterface 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.3
Number of the input interface for the Gigabit Ethernet interface that experienced the highest buffer level for the hour.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

apexGbeFrameBufferHourlyInUdp 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.4
Input UDP Port for the Gigabit Ethernet interface that experienced the highest buffer level for the hour.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

apexGbeFrameBufferHourlyInMulticastIp 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.5
Input Multicast IP address for the Gigabit Ethernet interface that experienced the highest buffer level for the hour.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexGbeFrameBufferHourlyInSourceIp 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.6
Input IGMP v3 Source IP for the Gigabit Ethernet interface that experienced the highest buffer level for the hour.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexGbeFrameBufferHourlyMaxMsLevel 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.7
The maximum Gigabit Ethernet frame buffer level (in milliseconds) recorded for the hour.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeFrameBufferHourlyMaxPercentFull 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.8
The maximum Gigabit Ethernet frame buffer level percentage recorded for the hour.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeFrameBufferHourlyGpsTime 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.9
The GPS time when the maximum Gigabit Ethernet frame buffer level was reached.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeFrameBufferHourlyOverflows 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.10
The number of overflows recorded on Gigabit Ethernet interface for the hour.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeFrameBufferHourlyResets 1.3.6.1.4.1.1166.1.31.7.2.7.3.1.11
The number of resets reported by the GigE processor during the hour.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeStatusInputTsUpdateInterval 1.3.6.1.4.1.1166.1.31.7.2.8.1.1
Time in seconds between Gigabit Ethernet Input Transport Stream Packet Count updates. The count during this time is defined as one sample. This time applies to packet counts contained in apexGbeStatusInputTsTable. To compute rate from packet count for the last update interval: Rate(bps) = (Packet_Count * 188 bytes/packet * 8 bits/byte) / Update_Interval This value is set by the APEX at startup and is constant.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeStatusInputTsTable 1.3.6.1.4.1.1166.1.31.7.2.8.2
Table of Gigabit Ethernet Input Transport Stream status. A row in this table corresponds to the same index row in apexInputTsStatTable and apexGbeStatusInputTsErrorTable. Packet Counts are updated every apexGbeStatusInputTsUpdateInterval. The count during a apexGbeStatusInputTsUpdateInterval is a sample. The samples are accumulated into a set of rolling statistics that cover a maximum of a 15 minute sampling time period. The sampling period is the amount of time over which the data in the corresponding row has been collected. When the sampling period reaches 15 minutes, old data is removed from the accumulated statistics and new data is rolled in. In this way, the average, minimum, and peak rates for the sampling period are maintained.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeStatusInputTsEntry

apexGbeStatusInputTsEntry 1.3.6.1.4.1.1166.1.31.7.2.8.2.1
Gigabit Ethernet Input Transport Stream Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeStatusInputTsEntry  

apexGbeStatInTsInputTsNum 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.1
The Gigabit Ethernet Input Transport Stream Status table index. A row in this table corresponds to the same index row in apexInputTsStatTable and apexGbeStatusInputTsErrorTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexGbeStatInTsSamplingPeriod 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.2
The total time, in seconds, over which the packet counts statistics in this row have been collected. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..900  

apexGbeStatInTsPriCurDataCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.3
The Data Packet Count of the most recent sample for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsPriAvgDataCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.4
The Average Data Packet Count per sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsPriMinDataCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.5
The Minimum Data Packet Count sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsPriPeakDataCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.6
The Peak Data Packet Count sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsPriCurStreamCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.7
The Transport Stream Packet Count of the most recent sample for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsPriAvgStreamCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.8
The Average Transport Stream Packet Count per sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsPriMinStreamCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.9
The Minimum Transport Stream Packet Count sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsPriPeakStreamCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.10
The Peak Transport Stream Packet Count sample during apexGbeStatInTsSamplingPeriod for the primary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsSecCurDataCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.11
The Data Packet Count of the most recent sample for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsSecAvgDataCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.12
The Average Data Packet Count per sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsSecMinDataCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.13
The Minimum Data Packet Count sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsSecPeakDataCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.14
The Peak Data Packet Count sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsSecCurStreamCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.15
The Transport Stream Packet Count of the most recent sample for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsSecAvgStreamCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.16
The Average Transport Stream Packet Count per sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsSecMinStreamCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.17
The Minimum Transport Stream Packet Count sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatInTsSecPeakStreamCount 1.3.6.1.4.1.1166.1.31.7.2.8.2.1.18
The Peak Transport Stream Packet Count sample during apexGbeStatInTsSamplingPeriod for the secondary. Refer to the description of apexGbeStatusInputTsTable for an explanation of packet counting. Refer to the description of apexGbeStatusInputTsUpdateInterval for an explanation of update interval and computing rates.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeStatusInputTsErrorTable 1.3.6.1.4.1.1166.1.31.7.2.8.3
Table of Gigabit Ethernet Input Transport Stream Error status. A row in this table corresponds to the same index row in apexInputTsStatTable and apexGbeStatusInputTsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeStatusInputTsErrorEntry

apexGbeStatusInputTsErrorEntry 1.3.6.1.4.1.1166.1.31.7.2.8.3.1
Gigabit Ethernet Input Transport Stream Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeStatusInputTsErrorEntry  

apexGbeStatInTsErrorInputTsNum 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.1
The Gigabit Ethernet Input Transport Stream Error Status table index. A row in this table corresponds to the same index row in apexInputTsStatTable and apexGbeStatusInputTsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexGbeStatInTsPriErrorSummary 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.2
The current highest error of the following errors for the primary input transport stream: apexGbeStatInTsPriLowBitRateError apexGbeStatInTsPriHighBitRateError apexGbeStatInTsMptsRedundPriError apexGbeStatInTsMptsRedundFailError apexGbeStatInTsPriLossInputError
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexGbeStatInTsPriLowBitRateError 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.3
The current low bit rate state for the primary input stream. Ok indicates no errors or not checking low bit rate. Error indicates primary input stream is below the low bit rate specified.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexGbeStatInTsPriHighBitRateError 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.4
The current high bit rate state for the primary input stream. Ok indicates no errors or not checking high bit rate. Error indicates primary input stream is above the high bit rate specified.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexGbeStatInTsMptsRedundPriError 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.5
The current redundant threshold state for the primary input stream. Ok indicates no errors or input stream is not part of a redundant pair. Error indicates primary input stream is below the threshold level specified.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexGbeStatInTsMptsRedundFailError 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.6
The current fail over state for a redundancy pair. Ok indicates no errors or input stream is not part of a redundant pair. Error indicates primary input stream is no longer in use and the APEX has fallen over to use the secondary input stream.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexGbeStatInTsSecErrorSummary 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.7
The current highest error state of the following for the secondary input transport stream: apexGbeStatInTsSecLowBitRateError apexGbeStatInTsSecHighBitRateError apexGbeStatInTsSecLossInputError
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexGbeStatInTsSecLowBitRateError 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.8
The current low bit rate state for the secondary input stream. Ok indicates no errors or not checking low bit rate. Error indicates secondary input stream is below the low bit rate specified.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexGbeStatInTsSecHighBitRateError 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.9
The current high bit rate state for the secondary input stream. Ok indicates no errors or not checking high bit rate. Error indicates secondary input stream is above the high bit rate specified.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexGbeStatInTsPriLossInputError 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.10
The current loss of input stream state for the primary input stream. Ok indicates no errors or not checking for loss of input stream. Error indicates primary input stream is missing.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexGbeStatInTsSecLossInputError 1.3.6.1.4.1.1166.1.31.7.2.8.3.1.11
The current loss of input stream state for the secondary input stream. Ok indicates no errors or not checking for loss of input stream. Error indicates secondary input stream is missing.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexGbeStatusInterfaceRedundTable 1.3.6.1.4.1.1166.1.31.7.2.9.1
This is a table of status parameters for GbE Interface Redundancy.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeStatusInterfaceRedundEntry

apexGbeStatusInterfaceRedundEntry 1.3.6.1.4.1.1166.1.31.7.2.9.1.1
GbE Interface Redundancy Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeStatusInterfaceRedundEntry  

apexGbeStatusInterfaceRedundIndex 1.3.6.1.4.1.1166.1.31.7.2.9.1.1.1
GbE Interface Pair number. Value of 1 is GbE1 and GbE2 pair. Value of 2 is GbE3 and GbE4 pair.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

apexGbeStatusInterfaceRedundActiveIf 1.3.6.1.4.1.1166.1.31.7.2.9.1.1.2
The current active interface for the redundant pair. This is only applicable if GbE Interface Redundancy is enabled for the pair. If GbE Interface Redundancy is not enabled it will be set to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

apexGbeStatusInterfaceRedundInvalidApplyText 1.3.6.1.4.1.1166.1.31.7.2.9.1.1.3
When apexGbeConfIfRedundApplyChange is set to applyNotInProgressInvalidData this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of an entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexGbeStatusInterfaceRedundFaultCondition 1.3.6.1.4.1.1166.1.31.7.2.9.1.1.4
Current fault condition of the GbE Interface pair. Reflects apexAlarmGbeInterfaceRedundFailOver for this redundant pair.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexGbeSfpUpdateStatus 1.3.6.1.4.1.1166.1.31.7.3.1.1.1
When set to 'update' the APEX will update the apexGbeSfpStatusTable by performing an one-time read of SFP memory. APEX sets back to 'updateNotInProgress' when complete. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(0), updateNotInProgress(1), update(2)  

apexGbeSfpStatusTable 1.3.6.1.4.1.1166.1.31.7.3.2.2
Table of SFP status parameters. Indexed by Gigabit Ethernet Interface Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeSfpStatusEntry

apexGbeSfpStatusEntry 1.3.6.1.4.1.1166.1.31.7.3.2.2.1
SFP status table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeSfpStatusEntry  

apexGbeSfpStatusGbeIfNum 1.3.6.1.4.1.1166.1.31.7.3.2.2.1.1
Gigabit Ethernet Interface Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexGbeSfpStatusVendorId 1.3.6.1.4.1.1166.1.31.7.3.2.2.1.2
ASCII format of bytes 0-127 from SFP-MSA ID Memory Map address A0h. Zero-length indicates that no SFP module is installed.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexGbeSfpStatusDiagInfo 1.3.6.1.4.1.1166.1.31.7.3.2.2.1.3
ASCII format of bytes 96-127 from SFP Diagnostic Memory address A2h. Zero-length indicates that diagnostic information is not available.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

apexQamConfigTransmissionMode 1.3.6.1.4.1.1166.1.31.8.1.1.1
This is the QAM Transmission Mode as defined in: Series J: Transmission of Television, Sound Programme and other Multimedia Signals, ITU-T J.83. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER annexB-ATSC-DCII(1), annexA-DVB(2), annexC-Asia-Pacific(3)  

apexQamModuleUpgradeSlot 1.3.6.1.4.1.1166.1.31.8.1.2.1
This is the QAM slot number of the QAM Module that is being upgraded from a 2x4 channel module to a 2x8 channel module. Zero indicates no slot selected. Once written, the change to this table will only take immediate effect after apexQamModuleUpgradeApplyChange is set to 'apply'. @Config(config=no, reboot=no) @Commit(param=apexQamModuleUpgradeApplyChange, value=2)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..3  

apexQamModuleUpgradeCode 1.3.6.1.4.1.1166.1.31.8.1.2.2
This is the encrypted upgrade code for the QAM Module that is being upgraded from a 2x4 channel module to a 2x8 channel module. The Upgrade Code is specific to a QAM Module and can only be used for the QAM Module with the serial number for which the Upgrade Code was created. Once written, the change to this parameter will only take immediate effect after the corresponding apexQamModuleUpgradeApplyChange is set to 'apply'. This parameter is cleared by the APEX after the apply is complete. @Config(config=no, reboot=no) @Commit(param=apexQamModuleUpgradeApplyChange, value=2)
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..48)  

apexQamModuleUpgradeApplyChange 1.3.6.1.4.1.1166.1.31.8.1.2.3
This is the Apply for QAM Module Upgrade Slot and Code. This parameter MUST be set to 'apply' in order for apexQamModuleUpgradeSlot and apexQamModuleUpgradeCode to take effect. This parameter MUST be set LAST after apexQamModuleUpgradeSlot and apexQamModuleUpgradeCode has been configured. The APEX will set this to applyNotInProgressInvalidData if the Upgrade Code is incorrect and the QAM Module is not upgraded. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexQamConfigApplyTable 1.3.6.1.4.1.1166.1.31.8.1.3
Table of Apply Change for the data for apexQamRfConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamConfigApplyEntry

apexQamConfigApplyEntry 1.3.6.1.4.1.1166.1.31.8.1.3.1
QAM Configuration Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamConfigApplyEntry  

apexQamConfigApplyRfPortNum 1.3.6.1.4.1.1166.1.31.8.1.3.1.1
The QAM RF Port number. Port 1,2,7,8 is Slot 1 Port 3,4,9,10 is Slot 2 Port 5,6,11,12 is Slot 3
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

apexQamConfigApplyChange 1.3.6.1.4.1.1166.1.31.8.1.3.1.2
The Apply for a row of data in apexQamRfConfigTable. A row in this table corresponds to the same row index in the apexQamRfConfigTable. This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the APEX. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexQamRfConfigTable 1.3.6.1.4.1.1166.1.31.8.1.4
Table of configuration items configurable on a QAM RF Port basis. There can be up to 12 RF Ports on an APEX1000 depending on how the 3 QAM slots are populated. There can be 2 or 4 RF Ports in each QAM slot. The 2 RF Ports in a 2x8(2x4) QAM module (1,2) in a QAM slot are mapped to table rows as follows: Slot Rows (RF port) 1 1,2 2 3,4 3 5,6 If a QAM Module in a slot only has 2 RF ports, the first three rows in this table for that slot are to be used. For example, if there is a 2x4 or 2x8 module in slot 3, port 5 and 6 are to be used for configuring the RF Ports of the module. The 4 RF Ports in a 4x4 QAM module (1,2,7,8) in a QAM slot are mapped to table rows as follows: Slot Rows (RF port) 1 1,2,7,8 2 3,4,9,10 3 5,6,11,12 All entries/rows in this table are used for the 4x4 QAM Module with any exceptions noted in the descriptions for the table entries. All entries in this table have the same ranges for the 4x4 QAM Module with any exceptions noted in the descriptions for the table entries. Refer to the description of apexQamChannelConfigTable for information on QAM Channel to RF Port mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules. Once written, the change to this table will only take immediate effect after apexQamConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamRfConfigEntry

apexQamRfConfigEntry 1.3.6.1.4.1.1166.1.31.8.1.4.1
QAM RF Port Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamRfConfigEntry  

apexQamRfConfigRfPortNum 1.3.6.1.4.1.1166.1.31.8.1.4.1.1
The QAM RF Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

apexQamRfConfigNumChannelsEnabled 1.3.6.1.4.1.1166.1.31.8.1.4.1.2
The number of QAM Channels enabled on the RF Port. APEX will not allow enabling of more channels than the installed QAM Module will support. Note that when this parameter is changed and applied there will be an interruption in service on all active channels on this RF Port. When QAM Transmission Mode is 'annexA-DVB', enabled channels is also limited by the Channel Spacing such that the total bandwidth of the RF must not exceed 48 MHz.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..8  

apexQamRfConfigModulationMode 1.3.6.1.4.1.1166.1.31.8.1.4.1.3
The QAM Modulation mode for the QAM RF Port. This is the QAM Modulation mode of all QAM Channels enabled on the RF Port. For 4x4 QAM Modules: This parameter applies on an RF pair basis, 1-2 and 7-8. APEX1000 will use only odd table indices. Even index of pair will be ignored and set to value for odd index of pair.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER qam64(1), qam256(2)  

apexQamRfConfigSymbolRate 1.3.6.1.4.1.1166.1.31.8.1.4.1.4
The Symbol Rate Setting of the QAM Channels enabled on the RF Port. It is in symbols per second (sps). When QAM Transmission Mode is 'annexA-DVB' the range is 800,000 sps to 6,980,000 sps in 1000 sps steps. When QAM Transmission Mode is 'annexC-Asia-Pacific' the range is 800,000 sps to 5,310,000 sps in 1000 sps steps. The APEX will correct values not on a 1000 sps boundary so the user or management system does not need to enforce the step size. When QAM Transmission Mode is 'annexB-ATSC-DCII' this parameter is not configurable and is set by the APEX based on QAM Modulation Mode. For 4x4 QAM Modules: This parameter applies on an RF pair basis, 1-2 and 7-8. APEX1000 will use only odd table indices. Even index of pair will be ignored and set to value for odd index of pair. @Range(step=1000)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 800000..6980000  

apexQamRfConfigSpectrumInvert 1.3.6.1.4.1.1166.1.31.8.1.4.1.5
The Spectrum Inversion Setting of the QAM Channels enabled on the RF Port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), invert(2)  

apexQamRfConfigTuningMode 1.3.6.1.4.1.1166.1.31.8.1.4.1.6
The tuning mode of the QAM Channels enabled on the RF Port. 'frequency' - The APEX tunes based on frequency as configured in RF Center Frequency for QAM Channel A and channel spacing as configured in RF Channel Spacing to determine the frequency of the B - H channels. 'channel' - The APEX tunes based on channel as configured in Channel Number for QAM Channel A using the selected Frequency Plan. The APEX will set the B - H channels to the next sequential channels. Applies only when QAM Transmission Mode is 'annexB-ATSC-DCII'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER frequency(1), channel(2)  

apexQamRfConfigEiaFrequencyPlan 1.3.6.1.4.1.1166.1.31.8.1.4.1.7
This is the frequency plan to use for tuning of the QAM Channels enabled on the RF Port. Frequency plans are as per CEA Standard: Cable Television Channel Identification Plan (CEA-542-B). This parameter is valid only when QAM Transmission Mode is 'annexB-ATSC-DCII'. 'std' - Standard (STD) North American frequency plan. 'hrc' - Harmonic Related Carrier (HRC) frequency plan. 'irc' - Incremental Related Carrier (IRC) frequency plan.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER std(1), hrc(2), irc(3)  

apexQamRfConfigEiaChanNumChannelA 1.3.6.1.4.1.1166.1.31.8.1.4.1.8
The Channel Number for QAM Channel A. Range is 0 to 158, with valid channels being 1 to 158 and 0 indicating 'not applicable'. This parameter is valid only when QAM Transmission Mode is 'annexB-ATSC-DCII'. This parameter is configurable only when Tuning Mode is 'channel'. When Tuning Mode is 'channel', this is the Channel Number used to determine the output frequency of QAM Channel A using the selected Frequency Plan. When Tuning Mode is 'frequency', this value is determined by the APEX using the selected Frequency Plan. If there is no channel number for the frequency, the value is set to zero. This parameter is not configurable for Transmission Modes of 'annexA-DVB' or 'annexC-Asia-Pacific' and the value is set to zero by the APEX. Channel 1 is not defined in CEA Standard: Cable Television Channel Identification Plan (CEA-542-B) for the Standard (STD) North American frequency plan. Channel 1 cannot be selected when apexQamRfConfigEiaFrequencyPlan is 'std'. Channel 2 as defined in defined in CEA Standard: Cable Television Channel Identification Plan (CEA-542-B) for the Harmonic Related Carrier (HRC) frequency plan is below the APEX 57 MHz minimum frequency. Channel 2 cannot be selected when apexQamRfConfigEiaFrequencyPlan is 'hrc'. For 4x4 QAM Modules: Channels with frequencies below 69 MHz may not be available. This limitation is dependent upon the HW version installed and number of channels enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..158  

apexQamRfConfigRfCenterFreqChannelA 1.3.6.1.4.1.1166.1.31.8.1.4.1.9
The RF Center Frequency for QAM Channel A. When QAM Transmission Mode is 'annexA-DVB' the range is 85,000,000 Hz to 999,000,000 Hz in 250,000 Hz steps. For 2x4/2x8 QAM Modules: When QAM Transmission Mode is 'annexB-ATSC-DCII' or 'annexC-Asia-Pacific' the range is 57,000,000 Hz to 999,000,000 Hz in 250,000 Hz steps. For 4x4 QAM Modules: When QAM Transmission Mode is 'annexB-ATSC-DCII' or 'annexC-Asia-Pacific' the range may be limited to 69,000,000 Hz to 999,000,000 Hz in 250,000 Hz steps. This limitation is dependent upon the HW version installed and number of channels enabled. The APEX will correct values not on a 250 kHz boundary so the user or management system does not need to enforce the step size. This parameter is configurable ONLY when Tuning Mode is 'frequency'. When Tuning Mode is 'channel', the value is set by the APEX using the selected Frequency Plan. @Range(step=250000)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 57000000..999000000  

apexQamRfConfigRfChanSpacing 1.3.6.1.4.1.1166.1.31.8.1.4.1.10
The Channel spacing for the QAM Channels enabled on the RF Port. This value must be in Hz in the range 1,000,000 Hz to 8,000,000 Hz in 500,000 Hz steps. The APEX will correct values not on a 500,000 Hz boundary so the user or management system does not need to enforce the step size. For 2x4/2x8 QAM Modules: When Transmission Mode is 'annexA-DVB' this value is configurable. Note that number of channels enabled can be affected by changing channel spacing. The total bandwidth of the RF must not exceed 48 MHz. For 2x4/2x8 QAM Modules: When Transmission Mode is 'annexB-ATSC-DCII' or 'annexC-Asia-Pacific' this value is fixed and is set by the APEX. For 4x4 QAM Modules: This value is fixed and is set by the APEX. @Range(step=500000)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1000000..8000000  

apexQamRfConfigRfLevelAttenuation 1.3.6.1.4.1.1166.1.31.8.1.4.1.11
The RF level attenuation setting of each enabled channel on the RF Port. Range is -300 to 800 representing -3 to 8 dB attenuation in 0.01 dB steps. (See 'Note' below.) Positive values are the amount below the nominal RF output level for the number of channels enabled on the RF Port. Negative values are the amount above the nominal. Number Nominal dBmV dBmV Channels dBmV W/-300 W/800 1 60 63 52 2 56 59 48 4 52 55 44 6 50 53 42 8 49 52 41 Note: Early APEX only supported attenuation. Gain was added later, hence the negative attenuation values for this parameter. For clarity, the APEX Element Manager display indicates 'RF Level Adjust', with a user selectable range of -8.00 to +3.00 dB, rather than 'Attenuation'. The APEX EM then sets this MIB parameter appropriately.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -300..800  

apexQamRfConfigRfLevelLowThreshold 1.3.6.1.4.1.1166.1.31.8.1.4.1.12
The threshold delta relative to the configured RF level that will indicate an RF Low condition. The measured output must drop this amount for RF Low condition. Range is 0 to 100 representing 0 to 10 dB in 0.1 dB steps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

apexQamRfConfigRfLevelHighThreshold 1.3.6.1.4.1.1166.1.31.8.1.4.1.13
The threshold delta relative to the configured RF level that will indicate an RF High condition. The measured output must rise this amount for RF High condition. Range is 0 to 100 representing 0 to 10 dB in 0.1 dB steps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

apexQamRfConfigMute 1.3.6.1.4.1.1166.1.31.8.1.4.1.14
Mute the RF Port. This will mute all QAM channels enabled on the RF Port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unmute(1), mute(2)  

apexQamRfConfigInterleaverDepth1 1.3.6.1.4.1.1166.1.31.8.1.4.1.15
The first of two Interleaver settings that can be assigned to the QAM Channels of this RF Port. Configurable only for Transmission Mode 'annexB-ATSC-DCII'. Values 1 to 12 used only for Transmission Mode 'annexB-ATSC-DCII'. Value 13 (i12-j17) used only for Transmission Modes 'annexA-DVB' and 'annexC-Asia-Pacific' and is set by the APEX.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER i64-j2(1), i32-j4(2), i16-j8(3), i8-j16(4), i128-j1(5), i128-j2(6), i128-j3(7), i128-j4(8), i128-j5(9), i128-j6(10), i128-j7(11), i128-j8(12), i12-j17(13)  

apexQamRfConfigInterleaverDepth2 1.3.6.1.4.1.1166.1.31.8.1.4.1.16
The second of two Interleaver settings that can be assigned to the QAM Channels of this RF Port. Configurable only for Transmission Mode 'annexB-ATSC-DCII'. Values 1 to 12 used only for Transmission Mode 'annexB-ATSC-DCII'. Value 13 (i12-j17) used only for Transmission Modes 'annexA-DVB' and 'annexC-Asia-Pacific' and is set by the APEX.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER i64-j2(1), i32-j4(2), i16-j8(3), i8-j16(4), i128-j1(5), i128-j2(6), i128-j3(7), i128-j4(8), i128-j5(9), i128-j6(10), i128-j7(11), i128-j8(12), i12-j17(13)  

apexQamChannelConfigTable 1.3.6.1.4.1.1166.1.31.8.1.5
Table of configuration items configurable on a QAM Channel basis. There are 48 Output Transport Streams (OTS) on an APEX1000. There can be up to 48 QAM Channels on an APEX1000 depending on how the 3 QAM slots are populated. There is a one-to-one mapping between QAM Channels and Output Transport Streams. QAM Channel (OTS) ranges are mapped to QAM slots as follows: Slot Channels 1 1..15 2 15..32 3 33..48 There can be either 4 or 8 QAM channels (OTS) on each RF Port. The slot and RF Port to QAM Channel (OTS) mappings for each QAM Module type are shown below. For a 2x4 or 2x8 QAM Module, QAM Channels (OTS) are mapped to RF Ports in a QAM Slot and table rows as follows: QAM Channel RF Port and OTS Slot/Port Table Row Table Rows 1/1 1 1..8 1/2 2 9..16 2/1 5 17..24 2/2 6 25..32 3/1 9 33..40 3/2 10 41..48 If a 2x4 QAM Module is in a slot, only the first four rows in this table for the slot/port are to be used. For example, if there is a 2x4 module in slot 3, rows 8..12 are to be used for configuring the QAM Channels of RF Port 1 on the module. For a 4x4 QAM Module, QAM Channels (OTS) are mapped to RF Ports in a QAM Slot and table rows as follows: QAM Channel RF Port and OTS Slot/Port Table Row Table Rows 1/1 1 1..4 1/2 2 5..8 1/3 7 9..12 1/4 8 13..16 2/1 3 17..20 2/2 4 21..24 2/3 9 25..28 2/4 10 29..32 3/1 5 33..36 3/2 6 37..40 3/3 11 41..44 3/4 12 45..48 Note that the QAM Channels on an RF Port are designated with the letters 'A'..'H' on the APEX Element Manager. Refer to the description of apexQamChannelConfigTable for information on QAM Channel to RF Port mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules. Once written, the change to this table will only take immediate effect after apexQamConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamChannelConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamChannelConfigEntry

apexQamChannelConfigEntry 1.3.6.1.4.1.1166.1.31.8.1.5.1
QAM Channel Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamChannelConfigEntry  

apexQamChanConfigChannelNum 1.3.6.1.4.1.1166.1.31.8.1.5.1.1
The QAM RF Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexQamChanConfigInterleaverSelect 1.3.6.1.4.1.1166.1.31.8.1.5.1.2
The interleaver selection for this Channel. Will use either apexQamRfConfigInterleaverDepth1 or apexQamRfConfigInterleaverDepth2.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER interleaverDepth1(1), interleaverDepth2(2)  

apexQamChanConfigTestMode 1.3.6.1.4.1.1166.1.31.8.1.5.1.3
Test mode setting for the QAM Channel. Setting to other than 'off' will cause a service interruption.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), cwtest(2), prbs23m(3), prbs23(5), mpegNull(6), suppress(9), prbs60(10), prbs63(11), prbs65(12), prbs68(13), prbs71(14), prbs73(15), prbs79(16), prbs81(17)  

apexQamRfRedundConfigApplyChange 1.3.6.1.4.1.1166.1.31.8.1.6.1.1
The Apply for QAM RF Redundancy Configuration parameters. This parameter MUST be set to 'apply' in order for the data to take effect. This parameter MUST be set LAST after all QAM RF Redundancy parameters affected by this parameter have been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexQamRfRedundConfigEnable 1.3.6.1.4.1.1166.1.31.8.1.6.1.2
Enables RF redundancy mode, allowing the APEX to failover to backup RF port and communicate with the REM1000. Allows for failover/ switching without requiring a REM1000 connection. Cannot be 'enabled' if the backup port (RF Port 6) is not present (there is no QAM Module in QAM slot 3). Cannot be 'enabled' if there are any mappings to any QAM Channel on the backup port. RF Port 6, QAM Channels 6A to 6H (Output Transport Streams 41 to 48). Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexQamRfRedundConfigRemConnection 1.3.6.1.4.1.1166.1.31.8.1.6.1.3
Configures how the APEX is connected to the REM1000. 'none' - Not connecting to REM1000. 'direct' - Connected to REM1000 dedicated IP interface through APEX Data IP (Enet2). Broadcast connection is always used in this case. Cannot be set to 'direct' if the QAM RF Redundancy UDP Port is in use on the Data IP Port (Enet2). QAM RF Redundancy UDP Port value is found in apexQamRfRedundStatusUdpPort. 'common' - Connected to REM1000 OAM&P interface through APEX OAM&P IP (Enet 1). Requires user to configure REM1000 IP address in apexQamRfRedundConfigRemCommonIpAddr. Cannot be set to 'common' if the QAM RF Redundancy UDP Port is in use on the OAM&P IP (Enet 1). QAM RF Redundancy UDP Port value is found in apexQamRfRedundStatusUdpPort. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), direct(1), common(2)  

apexQamRfRedundConfigApexId 1.3.6.1.4.1.1166.1.31.8.1.6.1.4
Identifies which set of RF inputs on the REM1000 are associated with this APEX. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..2  

apexQamRfRedundConfigRemCommonIpAddr 1.3.6.1.4.1.1166.1.31.8.1.6.1.5
Target REM1000 IP address. Must be singlecast address. Only used when apexQamRfRedundConfigRemConnection is set to 'common'. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexQamRfRedundConfigAutoSwitchBack 1.3.6.1.4.1.1166.1.31.8.1.6.1.6
This is the enable/disable of automatic switch back to the previous RF port from backup for QAM RF redundancy. When 'enabled', switch back to the previous RF port will automatically occur when the RF port comes back online. When 'disabled', the user must force back to the previous RF port using apexQamRfRedundConfigForceSwitch. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexQamRfRedundConfigSuspendFailover 1.3.6.1.4.1.1166.1.31.8.1.6.1.7
Enables and disables suspending of RF failover. Prevents failovers to or from backup. Force failover (apexQamRfRedundConfigForceSwitch) overrides this setting. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexQamRfRedundConfigForceSwitch 1.3.6.1.4.1.1166.1.31.8.1.6.1.8
Force a switch of an RF Port to or from the backup. Selects which RF Port to switch from. Overrides Suspend Failover (apexQamRfRedundConfigSuspendFailover). Parameter is ignored when: - apexQamRfRedundConfigEnable is 'disabled'. - backup is active and other than 'forceFromBackup' is selected. - backup is not active and 'forceFromBackup' is selected. 'forceFromBackup' will force back to the failed primary indicated in apexQamRfRedundStatusFailedPort. APEX sets back to 'switchNotInProgress' when complete. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER switchNotInProgress(0), forceFrom1(1), forceFrom2(2), forceFrom3(3), forceFrom4(4), forceFrom5(5), forceFromBackup(6)  

apexQamRfRedundConfigRemDirectIpOctet1 1.3.6.1.4.1.1166.1.31.8.1.6.1.9
Target REM1000 IP address first octet. Only used when apexQamRfRedundConfigRemConnection is set to 'direct'. The remainder of the IP address will be filled in by the APEX. The IP address used will be reflected in apexDataIpAddrInUse. Once written, the change to this parameter will only take immediate effect after apexQamRfRedundConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexQamRfRedundConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..126  

apexQamChannelConfigApplyTable 1.3.6.1.4.1.1166.1.31.8.1.7
Table of Apply Change for the data for apexQamChannelConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamChannelConfigApplyEntry

apexQamChannelConfigApplyEntry 1.3.6.1.4.1.1166.1.31.8.1.7.1
QAM Channel Configuration Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamChannelConfigApplyEntry  

apexQamChannelConfigApplyChannelNum 1.3.6.1.4.1.1166.1.31.8.1.7.1.1
The QAM Channel number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexQamChannelConfigApplyChange 1.3.6.1.4.1.1166.1.31.8.1.7.1.2
The Apply for a row of data in apexQamChannelConfigTable. A row in this table corresponds to the same row index in the apexQamChannelConfigTable. This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the APEX. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexQamStatusTransmissionMode 1.3.6.1.4.1.1166.1.31.8.2.1.1
This is the QAM Transmission Mode that is currently in use. QAM Transmission Mode is defined in: Series J: Transmission of Television, Sound Programme and other Multimedia Signals, ITU-T J.83.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER annexB-ATSC-DCII(1), annexA-DVB(2), annexC-Asia-Pacific(3)  

apexQamModuleInstalledCount 1.3.6.1.4.1.1166.1.31.8.2.1.2
Number of hot swappable QAM Modules currently installed.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexFanModuleInstalledCount 1.3.6.1.4.1.1166.1.31.8.2.1.3
Number of Fan-Only Modules currently installed in QAM Module slots.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamChannelsActiveCount 1.3.6.1.4.1.1166.1.31.8.2.1.4
Number of QAM Channels that are present (QAM Module installed) and enabled for use.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamModuleStatusTable 1.3.6.1.4.1.1166.1.31.8.2.2
Table of QAM Module Status. Refer to the descriptions of apexQamRfConfigTable and apexQamChannelConfigTable for information on QAM slot, RF Port mapping, and QAM Channel mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamModuleStatusEntry

apexQamModuleStatusEntry 1.3.6.1.4.1.1166.1.31.8.2.2.1
QAM Module Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamModuleStatusEntry  

apexQamModuleStatQamModuleNum 1.3.6.1.4.1.1166.1.31.8.2.2.1.1
QAM Module slot number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..3  

apexQamModuleStatInstalled 1.3.6.1.4.1.1166.1.31.8.2.2.1.2
Indicates if a module is installed and what type. notApplicable - When APEX does not boot properly. notInstalled - No QAM or Fan Module detected in slot. Reported in apexAlarmQamModuleFault. qam2x4Channel - A 2x4 Channel QAM Module installed. qam2x8Channel - A 2x8 Channel QAM Module installed. fanModule - A Fan Module installed. unsupported - Unknown module installed. Reported in apexAlarmQamModuleFault. removed - A QAM Module removed when there are active QAM channels. Reported in apexAlarmQamModuleFault. qamDiscovery - A QAM Module is present and type is being determined. qam4x4Channel - A 4x4 Channel QAM Module is installed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notInstalled(1), qam2x4Channel(2), qam2x8Channel(3), fanModule(4), unsupported(5), removed(6), qamDiscovery(7), qam4x4Channel(8)  

apexQamModuleStatFanSpeed 1.3.6.1.4.1.1166.1.31.8.2.2.1.3
The fan speed in RPM for installed QAM or Fan Module. Zero if not installed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexQamModuleStatFanFault 1.3.6.1.4.1.1166.1.31.8.2.2.1.4
Fan Fault. This fault is reported in apexAlarmFanFault not apexAlarmQamModuleFault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexQamModuleStatTemperature 1.3.6.1.4.1.1166.1.31.8.2.2.1.5
Temperature at sensor near the fan of the QAM Module or Fan Module in degrees Celsius.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamModuleStatTemperatureFault 1.3.6.1.4.1.1166.1.31.8.2.2.1.6
Temperature fault. This fault is reported in apexAlarmTemperatureFault not apexAlarmQamModuleFault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), overTemp(2)  

apexQamModuleStatError 1.3.6.1.4.1.1166.1.31.8.2.2.1.7
Summary of errors reported on an QAM Module basis. These errors are reported in apexAlarmQamModuleFault. ok - No errors. removed - Reflects apexQamModuleStatInstalled. unsupported - Reflects apexQamModuleStatInstalled. notInstalled - Reflects apexQamModuleStatInstalled. powerFault - Reflects apexQamModuleStatPowerFault. offline - Indicates the QAM Module and the RF Ports on it are being brought to operational mode after module is inserted or the module has recovered from a power fault. dc5VoltError - 5 Vdc error, see also apexQamModuleStat5VdcSupply and apexQamModuleStat5VdcFault. dc3-3VoltError - 3.3 Vdc error, see also apexQamModuleStat3dot3VdcSupply and apexQamModuleStat3dot3VdcFault. commLost - Communication Lost, see also apexQamModuleStatCommError. codeVersions - Incorrect Code Versions on module, see also apexQamModuleStatCodeInitError, apexQamQrmRevisionTable, and apexQamQrmRevisionStatusTable. codeDownload - Code Download In Progress, see also apexQrmDownloadStatusTable. codeDownloadError - Code Download Error, see also apexQrmDownloadStatusTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), removed(2), unsupported(3), notInstalled(4), powerFault(5), offline(6), dc5VoltError(7), dc3-3VoltError(8), commLost(9), codeVersions(10), codeDownload(11), codeDownloadError(12)  

apexQamModuleStatFaultCondition 1.3.6.1.4.1.1166.1.31.8.2.2.1.8
Current fault condition of the QAM Module errors. Reflects apexAlarmQamModuleFault for this QAM Module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexQamModuleStatFaultSumm 1.3.6.1.4.1.1166.1.31.8.2.2.1.9
Roll-up of QAM RF Port and QAM Channel fault conditions for this QAM Module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexQamModuleStatPowerFault 1.3.6.1.4.1.1166.1.31.8.2.2.1.10
Power fault. notApplicable - No module installed. ok - Power good. lowVoltageMainboard - Low voltage detected on Mainboard side of connector. lowVoltageQamModule - Low voltage detected on QAM Module side of connector. overCurrent - Over current detected on QAM Module. This fault is reported in apexAlarmQamModuleFault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), lowVoltageMainboard(2), lowVoltageQamModule(3), overCurrent(4)  

apexQamModuleStatBoardTemperature 1.3.6.1.4.1.1166.1.31.8.2.2.1.11
Temperature of the 4x4 QAM module board ('plate' temp) in degrees Celsius. Used only for 4x4 QAM Modules.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamModuleStatBoardTemperatureFault 1.3.6.1.4.1.1166.1.31.8.2.2.1.12
Board temperature fault of the 4x4 QAM module board ('plate' temp). Used only for 4x4 QAM Modules. This fault is reported in apexAlarmTemperatureFault not apexAlarmQamModuleFault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), overTemp(2)  

apexQamModuleStat5VdcSupply 1.3.6.1.4.1.1166.1.31.8.2.2.1.13
Measured level of the +5 VDC supply input of the 4x4 QAM module board. Used only for 4x4 QAM Modules. Range is 0 to 1000 representing 0 to 10 Volts in 0.01 Volt steps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1000  

apexQamModuleStat5VdcFault 1.3.6.1.4.1.1166.1.31.8.2.2.1.14
The +5 VDC supply fault of the 4x4 QAM module board. Used only for 4x4 QAM Modules. Indicates there is a problem with the direct 5 VDC supply or any internal module supply derived from the 5 VDC supply. Indicates voltage problem that can impair module function.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), low(2), high(3)  

apexQamModuleStat3dot3VdcSupply 1.3.6.1.4.1.1166.1.31.8.2.2.1.15
Measured level of the +3.3 VDC supply input of the 4x4 QAM module board. Used only for 4x4 QAM Modules. Range is 0 to 1000 representing 0 to 10 Volts in 0.01 Volt steps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1000  

apexQamModuleStat3dot3VdcFault 1.3.6.1.4.1.1166.1.31.8.2.2.1.16
The +3.3 VDC supply fault of the 4x4 QAM module board. Used only for 4x4 QAM Modules. Indicates there is a problem with the direct 3.3 VDC supply or any internal module supply derived from the 3.3 VDC supply. Indicates voltage problem that can impair module function.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), low(2), high(3)  

apexQamModuleStatCommError 1.3.6.1.4.1.1166.1.31.8.2.2.1.17
Communication with the 4x4 QAM Module has failed. Used only for 4x4 QAM Modules.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), inComm(1), commLost(2)  

apexQamModuleStatCodeInitError 1.3.6.1.4.1.1166.1.31.8.2.2.1.18
Code initialization error of the 4x4 QAM Module. Used only for 4x4 QAM Modules. Indicates a code, firmware, or FPGA startup issue. The module failed to load the FW/FPGA files to the devices or valid FW/FPGA files could not be found in the module. Code download is required to restore the module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexQamModuleSerialNumTable 1.3.6.1.4.1.1166.1.31.8.2.3
Table of QAM Module Serial Numbers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamModuleSerialNumEntry

apexQamModuleSerialNumEntry 1.3.6.1.4.1.1166.1.31.8.2.3.1
QAM Module Serial Number Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamModuleSerialNumEntry  

apexQamModuleSerialNumQamModuleNum 1.3.6.1.4.1.1166.1.31.8.2.3.1.1
QAM Module slot number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..3  

apexQamModuleSerialNumber 1.3.6.1.4.1.1166.1.31.8.2.3.1.2
The serial number of an installed QAM Module. Zero if not installed.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

apexQamQrmRevisionTable 1.3.6.1.4.1.1166.1.31.8.2.4
Table of QAM Module hardware and software revisions. There are 2 QRM modules on each 2x4/2x8 QAM Module. QRMs in QAM Module slots are mapped to table rows as follows: Slot/QRM Table Row 1/1 1 1/2 2 2/1 3 2/2 4 3/1 5 3/2 6 4x4 QAM Modules do not use QRM boards. There is only one board. These will be found in the odd indexed rows of this table. The even indexed rows of the table are not used for 4x4 QAM Modules. 4x4 QAM Modules in QAM Module slots are mapped to table rows as follows: Slot Table Row 1 1 2 3 3 5
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamQrmRevisionEntry

apexQamQrmRevisionEntry 1.3.6.1.4.1.1166.1.31.8.2.4.1
QAM Module Revision Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamQrmRevisionEntry  

apexQamQrmRevRfPortNum 1.3.6.1.4.1.1166.1.31.8.2.4.1.1
QAM Module Revision Table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..6  

apexQamQrmRevBoardId 1.3.6.1.4.1.1166.1.31.8.2.4.1.2
Model ID of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Hex XXYY.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexQamQrmRevAppFw 1.3.6.1.4.1.1166.1.31.8.2.4.1.3
Application firmware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Hex XXYY where XX is major version and YY is minor version. 'FFFF' indicates no valid application code is present.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexQamQrmRevBootLoaderFw 1.3.6.1.4.1.1166.1.31.8.2.4.1.4
Boot loader firmware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Hex XXYY where XX is major version and YY is minor version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexQamQrmRevFpga 1.3.6.1.4.1.1166.1.31.8.2.4.1.5
FPGA version of the 2x4/2x8 QAM Module's QRM board or FPGA1 version of the 4x4 QAM Module. Hex XXYY where XX is major version and YY is minor version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexQamQrmRevHw 1.3.6.1.4.1.1166.1.31.8.2.4.1.6
Hardware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Hex XXYY where XX is major version and YY is minor version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexQamQrmRevSerialNumber 1.3.6.1.4.1.1166.1.31.8.2.4.1.7
The serial number of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Modules. Zero if not installed.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

apexQamQrmRevFpga2 1.3.6.1.4.1.1166.1.31.8.2.4.1.8
FPGA2 version of the 4x4 QAM Module. Used only for 4x4 QAM Modules. Hex XXYY where XX is major version and YY is minor version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexQamRfPortStatusTable 1.3.6.1.4.1.1166.1.31.8.2.5
Table of QAM RF Port Status. Refer to the descriptions of apexQamRfConfigTable and apexQamChannelConfigTable for information on QAM slot, RF Port mapping, and QAM Channel mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamRfPortStatusEntry

apexQamRfPortStatusEntry 1.3.6.1.4.1.1166.1.31.8.2.5.1
QAM RF Port Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamRfPortStatusEntry  

apexQamRfPortStatRfPortNum 1.3.6.1.4.1.1166.1.31.8.2.5.1.1
RF Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

apexQamRfPortStatInfoRate 1.3.6.1.4.1.1166.1.31.8.2.5.1.2
The information rate of the QAM channels on this RF Port in bits per second.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexQamRfPortStatNumChannelsActive 1.3.6.1.4.1.1166.1.31.8.2.5.1.3
Number of QAM Channels that are present (QAM Module installed) and enabled for use on this RF Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..8  

apexQamRfPortStatOutputLevel 1.3.6.1.4.1.1166.1.31.8.2.5.1.4
Measured per channel RF Output Level. Range is 0 to 8000 representing 0 to 80 dBmV in 0.01 dBmV steps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..8000  

apexQamRfPortStatOutputLevelFault 1.3.6.1.4.1.1166.1.31.8.2.5.1.5
RF Output Level fault. Indicates if the user configured apexQamRfConfigRfLevelLowThreshold or apexQamRfConfigRfLevelHighThreshold has been reached.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), low(2), high(3)  

apexQamRfPortStatTemperature 1.3.6.1.4.1.1166.1.31.8.2.5.1.6
Temperature of the 2x4/2x8 QAM Module's QRM board ('plate' temp) in degrees Celsius. Used only for 2x4/2x8 QAM Modules.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamRfPortStatTemperatureFault 1.3.6.1.4.1.1166.1.31.8.2.5.1.7
Temperature fault of the 2x4/2x8 QAM Module's QRM board ('plate' temp). Used only for 2x4/2x8 QAM Modules. This fault is reported in apexAlarmTemperatureFault not apexAlarmQamRfPortFault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), overTemp(2)  

apexQamRfPortStat5VdcSupply 1.3.6.1.4.1.1166.1.31.8.2.5.1.8
Measured level of the +5 VDC supply input of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Modules. Range is 0 to 1000 representing 0 to 10 Volts in 0.01 Volt steps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1000  

apexQamRfPortStat5VdcFault 1.3.6.1.4.1.1166.1.31.8.2.5.1.9
The +5 VDC supply fault of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Modules. Indicates voltage problem that can impair QRM function.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), low(2), high(3)  

apexQamRfPortStat3dot3VdcSupply 1.3.6.1.4.1.1166.1.31.8.2.5.1.10
Measured level of the +3.3 VDC supply input of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Modules. Range is 0 to 1000 representing 0 to 10 Volts in 0.01 Volt steps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1000  

apexQamRfPortStat3dot3VdcFault 1.3.6.1.4.1.1166.1.31.8.2.5.1.11
The +3.3 VDC supply fault of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Modules. Indicates voltage problem that can impair QRM function.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), low(2), high(3)  

apexQamRfPortStatFreqPllLock 1.3.6.1.4.1.1166.1.31.8.2.5.1.12
Frequency tuning PLL lock status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), locked(1), notLocked(2)  

apexQamRfPortStatRefClockPresent 1.3.6.1.4.1.1166.1.31.8.2.5.1.13
External reference clock present indication.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), present(1), notPresent(2)  

apexQamRfPortStatRefClockLock 1.3.6.1.4.1.1166.1.31.8.2.5.1.14
Board not phase-locked to the External reference clock.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), locked(1), notLocked(2)  

apexQamRfPortStatDataClockPresent 1.3.6.1.4.1.1166.1.31.8.2.5.1.15
Data clock present indication.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), present(1), notPresent(2)  

apexQamRfPortStatDataSyncFault 1.3.6.1.4.1.1166.1.31.8.2.5.1.16
One or more of the QAM Channel data interfaces is not synchronized.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), inSync(1), syncLost(2)  

apexQamRfPortStatCommError 1.3.6.1.4.1.1166.1.31.8.2.5.1.17
Communication with the 2x4/2x8 QAM Module's QRM board has failed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), inComm(1), commLost(2)  

apexQamRfPortStatError 1.3.6.1.4.1.1166.1.31.8.2.5.1.18
Error status on an RF Port basis. These errors are reported in apexAlarmQamRfPortFault. 'major' for: 'outputRfLevel', 'dc5VoltError', 'dc3-3VoltError'. 'critical' for: 'freqPllNotLocked', 'extClkNotPresent', 'extClkNotLocked', 'dataClkNotPresent', 'dataSyncLost', 'commLost', 'codeVersions', 'codeDownload', 'codeDownloadError', 'unsupportedQrm', or 'configFailed'. outputRfLevel - RF Output Level error, see also apexQamRfPortStatOutputLevel and apexQamRfPortStatOutputLevelFault. dc5VoltError - 5 Vdc error, see also apexQamRfPortStat5VdcSupply and apexQamRfPortStat5VdcFault. dc3-3VoltError - 3.3 Vdc error, see also apexQamRfPortStat3dot3VdcSupply and apexQamRfPortStat3dot3VdcFault. freqPllNotLocked - Frequency PLL not locked, see also apexQamRfPortStatFreqPllLock. extClkNotPresent - External Reference Clock Not Present, see also apexQamRfPortStatRefClockPresent. extClkNotLocked - Not Locked to External Reference Clock, see also apexQamRfPortStatRefClockLock. dataClkNotPresent - Data Clock Not Present, see also apexQamRfPortStatDataClockPresent. dataSyncLost - Data Synchronization Lost, see also apexQamRfPortStatDataSyncFault. commLost - Communication Lost, see also apexQamRfPortStatCommError. unsupportedQrm - QRM Revision Not Supported, see also apexQamQrmRevisionTable and apexQamQrmRevisionStatusTable. configFailed - RF Port Configuration Failed. codeVersions - Incorrect Code Versions on QRM, see also apexQamRfPortStatCodeInitError, apexQamQrmRevisionTable, and apexQamQrmRevisionStatusTable. codeDownload - Code Download In Progress, see also apexQrmDownloadStatusTable. codeDownloadError - Code Download Error, see also apexQrmDownloadStatusTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), outputRfLevel(2), dc5VoltError(3), dc3-3VoltError(4), freqPllNotLocked(5), extClkNotPresent(6), extClkNotLocked(7), dataClkNotPresent(8), dataSyncLost(9), commLost(10), unsupportedQrm(11), configFailed(12), codeVersions(13), codeDownload(14), codeDownloadError(15)  

apexQamRfPortStatFaultCondition 1.3.6.1.4.1.1166.1.31.8.2.5.1.19
Current fault condition of the RF Port errors. Reflects apexAlarmQamRfPortFault for this RF Port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexQamRfPortStatChanFaultSumm 1.3.6.1.4.1.1166.1.31.8.2.5.1.20
Roll-up of Channel fault conditions for this RF Port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexQamRfPortStatCodeInitError 1.3.6.1.4.1.1166.1.31.8.2.5.1.21
Code initialization error of the 2x4/2x8 QAM Module's QRM board. Indicates a code, firmware, or FPGA startup issue. 'fpgaInitError' - FPGA not loaded. Caused by incompatible code images or corrupted FPGA image on the QRM. 'calDataError' - Working copy of calibration data was corrupted and needs to be restored by code download process. Caused by interruption of previous code download process.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), fpgaInitError(2), calDataError(3)  

apexQamChannelStatusTable 1.3.6.1.4.1.1166.1.31.8.2.6
Table of QAM Channel Status. Refer to the descriptions of apexQamRfConfigTable and apexQamChannelConfigTable for information on QAM slot, RF Port mapping, and QAM Channel mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamChannelStatusEntry

apexQamChannelStatusEntry 1.3.6.1.4.1.1166.1.31.8.2.6.1
QAM Channel Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamChannelStatusEntry  

apexQamChanStatChannelNum 1.3.6.1.4.1.1166.1.31.8.2.6.1.1
QAM Channel number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexQamChanStatActive 1.3.6.1.4.1.1166.1.31.8.2.6.1.2
'active' indicates that mappings can be made to the channel. This means that either: 1) The channel is present (apexQamModuleStatInstalled 'qam2x4Channel' or 'qam2x8Channel') and enabled for use (apexQamRfConfigNumChannelsEnabled); 2) Or, the channel is on the backup RF port when QAM RF Redundancy is enabled (apexQamRfRedundConfigEnable).
Status: current Access: read-only
OBJECT-TYPE    
  ActiveTYPE  

apexQamChanStatRfFreq 1.3.6.1.4.1.1166.1.31.8.2.6.1.3
The center frequency for the QAM Channel in Hz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamChanStatEiaChanNum 1.3.6.1.4.1.1166.1.31.8.2.6.1.4
The EIA Channel number for the QAM Channel. Will be zero if there is no EIA Channel number corresponding to the frequency in use.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamChanStatDataPresent 1.3.6.1.4.1.1166.1.31.8.2.6.1.5
Indication of MPEG data activity on the interface for this QAM channel. This includes MPEG null packets.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), data(1), noData(2)  

apexQamChanStatError 1.3.6.1.4.1.1166.1.31.8.2.6.1.6
Summary of errors reported on a QAM channel. This is enumerated and the reported error will be the most severe.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), noData(2)  

apexQamChanStatFaultCondition 1.3.6.1.4.1.1166.1.31.8.2.6.1.7
Current fault condition of the QAM channel errors. Reflects apexAlarmQamChannelFault for this QAM Channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexQamRfRedundStatusBackupPort 1.3.6.1.4.1.1166.1.31.8.2.7.1.1
State of configured backup port. 'disabled' - QAM RF Redundancy is disabled. 'standby' - QAM RF Redundancy is enabled but backup is inactive. No failure has occurred. 'active' - Failover has occurred and backup is active. Refer to apexQamRfRedundStatusFailedPort for port being backed up. 'failed' - Backup port has failed. APEX cannot provide RF redundancy. 'removed' - QAM Module with Backup port has been removed. APEX cannot provide RF redundancy.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), standby(1), active(2), failed(3), removed(4)  

apexQamRfRedundStatusFailedPort 1.3.6.1.4.1.1166.1.31.8.2.7.1.2
Indicates which port (1 to 5) has failed over to the backup port. Zero indicates backup port is not active.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamRfRedundStatusMismatch 1.3.6.1.4.1.1166.1.31.8.2.7.1.3
Indicates whether there is a potential for channels being lost when failing to the backup or when switching back to a primary due to a mixture of 2x4 and 2x8 QAM Modules. Indicates whether RF redundancy is unavailable due to a 4x4 QAM Module installed. A 2x4 QAM Module is capable of supporting a maximum of 4 channels per RF port. A 2x8 QAM Module is capable of supporting a maximum of 8 channels per RF port. The number of channels enabled (apexQamRfConfigNumChannelsEnabled) is not considered. 'notApplicable' - QAM RF Redundancy is disabled. 'noMismatch' - Indicates no channels would be lost because there is no mismatch. 'backup2x4' - Indicates a loss of channels could occur on failover to the backup because the backup RF Port is in a 2x4 module and at least one primary RF Port is in a 2x8 module. 'primary2x4' - Indicates a loss of channels could occur on switch- back from the backup to the primary because the backup RF Port is in a 2x8 module and the primary RF Port is in a 2x4 module. This would occur if the failed 2x8 primary is replaced with a 2x4. 'any4x4' - Indicates a 4x4 QAM Module is installed in any slot and RF Redundancy is not available. Failover and/or switchback are suspended until the 4x4 is replaced.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), noMismatch(1), backup2x4(2), primary2x4(3), any4x4(4)  

apexQamRfRedundStatusUdpPort 1.3.6.1.4.1.1166.1.31.8.2.7.1.4
UDP Port that is used for QAM RF Redundancy communication between the APEX and REM. When apexQamRfRedundConfigRemConnection is: 'direct' - APEX sends/receives broadcast on this UDP Port. 'common' - APEX sends/receives singlecast on this UDP Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamRfRedundStatusRemConnection 1.3.6.1.4.1.1166.1.31.8.2.7.1.5
State of communication with REM. 'notApplicable' - QAM RF Redundancy is not enabled and/or the connection to the REM is not enabled. 'notConnected' - Initial condition. APEX has not sent a switch_port() message yet. 'connected' - received ack() message from REM for current switch_port() message. 'connectionLost' - REM has not replied to last 3 heartbeat switch_port() messages.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notConnected(1), connected(2), connectionLost(3)  

apexQamRfRedundStatusRemError 1.3.6.1.4.1.1166.1.31.8.2.7.1.6
Status of REM1000 taken from error_code field in REM1000 ack() response (defined in REM1000 Message Stream Protocol). Valid only when apexQamRfRedundConfigRemConnection is other than 'none'. Values as defined in REM1000 MSP: 0x00 - No Errors. No problems switching, parsing switch_port() message, or with HW. 0x01 - Invalid apex_id value in prior switch_port() message. 0x02 - Invalid msg_type value in prior switch_port() message. 0x03 - Invalid port value in prior switch_port() message. 0x04 - Error switching after receiving valid switch_port() message. 0x05 - Minor HW error. REM can still switch. 0x81 - Apex_id Conflict. Switch_port() messages with the same apex_id have been received from multiple APEXs. Switch reset to pass- through configuration. 0x85 - Major HW error. REM failure. Switch reset to pass-through configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamRfRedundStatusRemSwitch 1.3.6.1.4.1.1166.1.31.8.2.7.1.7
Status of the REM1000 switches indicated through ack() response from REM1000 (e.g. pass-through or switching port 'x'). Valid only when apexQamRfRedundConfigRemConnection is other than 'none'. Zero indicates REM is in passing inputs 1 to 5 straight through to outputs 1 to 5. Values of 1 to 5 indicate REM backup input port is switched to output port 1 to 5 and other ports are passed through.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexQamRfRedundStatusInvalidApplyText 1.3.6.1.4.1.1166.1.31.8.2.7.1.8
When apexQamRfRedundConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexQamRfPortMuteStatusTable 1.3.6.1.4.1.1166.1.31.8.2.8
Table of QAM RF Port Mute Status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamRfPortMuteStatusEntry

apexQamRfPortMuteStatusEntry 1.3.6.1.4.1.1166.1.31.8.2.8.1
QAM RF Port Mute Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamRfPortMuteStatusEntry  

apexQamRfPortMuteStatusRfPortNum 1.3.6.1.4.1.1166.1.31.8.2.8.1.1
RF Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

apexQamRfPortMuteStatus 1.3.6.1.4.1.1166.1.31.8.2.8.1.2
Indicates whether the QAM channels on the RF port are muted or unmuted.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unmuted(1), muted(2)  

apexQamQrmRevisionStatusTable 1.3.6.1.4.1.1166.1.31.8.2.9
Table of status of QRM hardware and software revisions. Indications of whether they are supported, current, etc.. There are 2 QRM modules on each 2x4/2x8 QAM Module. QRMs in QAM Module slots are mapped to table rows as follows: Slot/QRM Table Row 1/1 1 1/2 2 2/1 3 2/2 4 3/1 5 3/2 6 4x4 QAM Modules do not use QRM boards. There is only one board. These will be found in the odd indexed rows of this table. The even indexed rows of the table are not used for 4x4 QAM Modules. 4x4 QAM Modules in QAM Module slots are mapped to table rows as follows: Slot Table Row 1 1 2 3 3 5
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamQrmRevisionStatusEntry

apexQamQrmRevisionStatusEntry 1.3.6.1.4.1.1166.1.31.8.2.9.1
QRM Revision Status Table Entry
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamQrmRevisionStatusEntry  

apexQamQrmRevStatQrmNum 1.3.6.1.4.1.1166.1.31.8.2.9.1.1
QRM Revision Status Table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..6  

apexQamQrmRevStatBoardId 1.3.6.1.4.1.1166.1.31.8.2.9.1.2
Status of the Model ID of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQamQrmRevisionTable for the revisions of each QRM.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notSupported(1), supported(2)  

apexQamQrmRevStatAppFw 1.3.6.1.4.1.1166.1.31.8.2.9.1.3
Status of Application firmware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQamQrmRevisionTable for the revisions of each 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQrmFileRevisionTable for the revisions of files in the APEX release resident on the device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notSupported(1), belowRelease(2), atRelease(3), aboveRelease(4)  

apexQamQrmRevStatBootLoaderFw 1.3.6.1.4.1.1166.1.31.8.2.9.1.4
Status of Boot loader firmware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQamQrmRevisionTable for the revisions of each 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notSupported(1), supported(2)  

apexQamQrmRevStatFpga 1.3.6.1.4.1.1166.1.31.8.2.9.1.5
Status of FPGA version of the 2x4/2x8 QAM Module's QRM board or FPGA1 version of the 4x4 QAM Module. Refer to apexQamQrmRevisionTable for the revisions of each 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQrmFileRevisionTable for the revisions of files in the APEX release resident on the device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notSupported(1), belowRelease(2), atRelease(3), aboveRelease(4)  

apexQamQrmRevStatHw 1.3.6.1.4.1.1166.1.31.8.2.9.1.6
Status of Hardware version of the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board. Refer to apexQamQrmRevisionTable for the revisions of each 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notSupported(1), supported(2)  

apexQamQrmRevStatQrmSupported 1.3.6.1.4.1.1166.1.31.8.2.9.1.7
Indicates if the 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board is supported. Summary of above status. If any 4x4 QAM Module or the 2x4/2x8 QAM Module's QRM board revision status is 'notSupported' this parameter will indicate 'notSupported' and apexQamRfPortStatError will report 'unsupportedQrm'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notSupported(1), supported(2)  

apexQamQrmRevStatFpga2 1.3.6.1.4.1.1166.1.31.8.2.9.1.8
Status of FPGA2 version of the 4x4 QAM Module. Refer to apexQamQrmRevisionTable for the revisions of each 4x4 QAM Module. Refer to apexQrmFileRevisionTable for the revisions of files in the APEX release resident on the device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notSupported(1), belowRelease(2), atRelease(3), aboveRelease(4)  

apexQamRfPortChannelInfoTable 1.3.6.1.4.1.1166.1.31.8.2.10
Table of QAM Channel information for each QAM RF Port. Refer to the descriptions of apexQamRfConfigTable and apexQamChannelConfigTable for information on QAM slot, RF Port mapping, and QAM Channel mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamRfPortChannelInfoEntry

apexQamRfPortChannelInfoEntry 1.3.6.1.4.1.1166.1.31.8.2.10.1
QAM RF Port Channel Information Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamRfPortChannelInfoEntry  

apexQamRfPortChannelInfoRfPortNum 1.3.6.1.4.1.1166.1.31.8.2.10.1.1
RF Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

apexQamRfPortChannelInfoChanA 1.3.6.1.4.1.1166.1.31.8.2.10.1.2
QAM Channel number (Output Transport number) of QAM Channel 'A' on this RF port. This may be used to access data in tables indexed by QAM Number or Output Transport Stream. Used in combination with apexQamRfPortChannelInfoChanCount, data for all QAM Channels on this RF Port may be accessed. '0' - Indicates RF Port is not present.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 1 | 5 | 9 | 13 | 17 | 21 | 25 | 29 | 33 | 37 | 41 | 45  

apexQamRfPortChannelInfoChanCount 1.3.6.1.4.1.1166.1.31.8.2.10.1.3
The number of QAM Channels on the RF port. '0' - Indicates RF Port is not present. '4' - RF Port has 4 QAM Channels, 'A'-'D'. '8' - RF Port has 8 QAM Channels, 'A'-'H'.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 4 | 8  

apexQamChannelIdTable 1.3.6.1.4.1.1166.1.31.8.2.11
Table of QAM Channel Identification data. Identifies the physical location of the QAM Channel (Output Transport Stream) in the APEX chassis. Refer to the descriptions of apexQamRfConfigTable and apexQamChannelConfigTable for information on QAM slot, RF Port mapping, and QAM Channel mapping. Tables apexQamRfPortChannelInfoTable and apexQamChannelIdTable can be used to assist in referencing between QAM slots, RF Ports, and QAM Channels (Output Transport Streams) for the installed modules.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQamChannelIdEntry

apexQamChannelIdEntry 1.3.6.1.4.1.1166.1.31.8.2.11.1
QAM Channel Identification Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQamChannelIdEntry  

apexQamChannelIdChannelNum 1.3.6.1.4.1.1166.1.31.8.2.11.1.1
QAM Channel number (Output Transport number).
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexQamChannelIdSlotNum 1.3.6.1.4.1.1166.1.31.8.2.11.1.2
QAM Slot number of the channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..3  

apexQamChannelIdRfPortNum 1.3.6.1.4.1.1166.1.31.8.2.11.1.3
RF Port number of the channel. This may be used to access data in tables indexed by RF Port Number. '0' - Indicates QAM Channel is not present.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..12  

apexQamChannelIdModuleRfPortNum 1.3.6.1.4.1.1166.1.31.8.2.11.1.4
Module RF Port number of the channel. Corresponds to RF Port numbering on the back of physical QAM Module. '0' - Indicates QAM Channel is not present.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

apexQamChannelIdChannelLetter 1.3.6.1.4.1.1166.1.31.8.2.11.1.5
The letter symbol ('A'..'H') for the channel. String will be empty if QAM Channel not present.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..1)  

apexQamChannelIdChannelDescription 1.3.6.1.4.1.1166.1.31.8.2.11.1.6
Text description for the QAM Channel (Output Transport Stream). Format is as follows where brackets and bracketed descriptions are replaced by a number/letter as appropriate: [QAM Channel / TS Num]:Slot[QAM Slot Num]-[Module Rf Port Num][Channel Letter] Examples: TS 9, in QAM Slot 1, on RF Port 2: '09:Slot1-2A' TS 17, in QAM Slot 2, on RF Port 1: '17:Slot2-1A' TS 48, in QAM Slot 3, on RF Port 2: '48:Slot3-2H' TS 48, in QAM Slot 3, on RF Port 4: '48:Slot3-4D' This may be used for display purposes on a management system. String will be empty or contain '[QAM Channel / TS Num]:Inactive' if apexQamChanStatActive is not set to 'active', i.e. if QAM Channel is not present and/or not enabled.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..11)  

apexQrmDownloadConfigTable 1.3.6.1.4.1.1166.1.31.8.3.1.2
Table of QAM Module Code Download Configuration. There are 2 QRM modules on each 2x4/2x8 QAM Module. QRMs in QAM Module slots are mapped to table rows as follows: Slot/QRM Table Row 1/1 1 1/2 2 2/1 3 2/2 4 3/1 5 3/2 6 4x4 QAM Modules do not use QRM boards. There is only one board. These will be found in the odd indexed rows of this table. The even indexed rows of the table are not used for 4x4 QAM Modules. 4x4 QAM Modules in QAM Module slots are mapped to table rows as follows: Slot Table Row 1 1 2 3 3 5
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQrmDownloadConfigEntry

apexQrmDownloadConfigEntry 1.3.6.1.4.1.1166.1.31.8.3.1.2.1
QAM Code Download Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQrmDownloadConfigEntry  

apexQrmDownloadConfigQrmNum 1.3.6.1.4.1.1166.1.31.8.3.1.2.1.1
QAM Code Download Configuration Table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..6  

apexQrmDownloadConfigRequest 1.3.6.1.4.1.1166.1.31.8.3.1.2.1.2
User initiated manual 4x4 QAM Module or 2x4/2x8 QAM Module QRM board Code Download request. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER requestNotInProgress(0), requestDownload(1)  

apexQrmDownloadStatusTable 1.3.6.1.4.1.1166.1.31.8.3.2.2
Table of QAM Module Code Download Status. Refer to apexQrmDownloadConfigTable description for table indexing information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQrmDownloadStatusEntry

apexQrmDownloadStatusEntry 1.3.6.1.4.1.1166.1.31.8.3.2.2.1
QRM Code Download Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQrmDownloadStatusEntry  

apexQrmDownloadStatusRfPortNum 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.1
QAM Code Download Status Table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..6  

apexQrmDownloadStatusDescription 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.2
Text description of the current state of 4x4 QAM Module or 2x4/2x8 QAM Module QRM board Code Download.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexQrmDownloadProgress 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.3
Completion percentage of Code Download. '-1' indicates failure.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..100  

apexQrmDownloadSupported 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.4
Indicates if the module HW and SW will support Code Download. 'notSupported' if the module is unsupported or the code download might downgrade the code resident on the module. Refer to apexQamQrmRevisionTable, apexQamQrmRevisionStatusTable, and apexQrmDownloadFileSet for additional status. The user cannot initiate a manual download (apexQrmDownloadConfigRequest) when download 'notSupported'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notSupported(1), supported(2)  

apexQrmDownloadRequired 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.5
Indicates if the module requires Code Download. Code download is needed if the versions are not up to date with the resident APEX FW Release. Refer to apexQamQrmRevisionTable, apexQamQrmRevisionStatusTable, and apexQrmDownloadFileSet for additional status. The user can initiate a manual download (apexQrmDownloadConfigRequest) when download 'notRequired'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notRequired(1), required(2)  

apexQrmDownloadFileSet 1.3.6.1.4.1.1166.1.31.8.3.2.2.1.6
Indicates which file set will be used for this module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), fileSet1(1), fileSet2(2), fileSet3(3)  

apexQrmFileRevisionTable 1.3.6.1.4.1.1166.1.31.8.3.2.3
Table of revisions of QAM Module files released with the resident APEX FW Release. Refer to identSoftwareVersion in BCS-IDENT-MIB for the release number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexQrmFileRevisionEntry

apexQrmFileRevisionEntry 1.3.6.1.4.1.1166.1.31.8.3.2.3.1
QRM File Revision Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexQrmFileRevisionEntry  

apexQrmFileRevFileSetNum 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.1
QAM file set number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..3  

apexQrmFileRevFirmware 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.2
Revision of the Application firmware file of the 2x4/2x8 QAM Module's QRM board or revision of the Application firmware portion of the 4x4 QAM Module Code File. Hex XXYY where XX is major version and YY is minor version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexQrmFileRevCalibration 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.3
Revision of the Calibration data file of the 2x4/2x8 QAM Module's QRM board. Used only for 2x4/2x8 QAM Module QRM board file sets. Hex XXYY where XX is major version and YY is minor version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexQrmFileRevFpga 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.4
Revision of FPGA firmware file of the 2x4/2x8 QAM Module's QRM board or revision of the FPGA1 firmware portion of the 4x4 QAM Module Code File. Hex XXYY where XX is major version and YY is minor version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexQrmFileRevFpga2 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.5
Revision of FPGA2 firmware portion of the 4x4 QAM Module Code File. Used only for 4x4 QAM Module file sets. Hex XXYY where XX is major version and YY is minor version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

apexQrmFileRevDateTime 1.3.6.1.4.1.1166.1.31.8.3.2.3.1.6
Date and time the 4x4 QAM Module code file was created. Used only for 4x4 QAM Module file sets. Format: 'MM/DD/YYYY HH:MM' Where HH is a 24 hour clock.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

apexSesContConfProtocol 1.3.6.1.4.1.1166.1.31.9.1.1.1
The communication protocol for output streams in Session Control operating mode. This determines the type of protocol the APEX will use to communicate with an Edge Resource Manager/Switch Digital Video Manager. This parameter cannot be changed when there are any active Session Control mappings. All Session Control mappings must be removed prior to changing this protocol. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), rpc(1), rtsp(2), mha-ermi(3)  

apexSesContConfTableApplyChange 1.3.6.1.4.1.1166.1.31.9.1.1.2
The Apply for the apexSesContConfTable. This parameter MUST be set to 'apply' in order for any of the data in the apexSesContConfTable to take effect. This parameter MUST be set LAST after all other data in the apexSesContConfTable has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexSesContConfRateCompareType 1.3.6.1.4.1.1166.1.31.9.1.1.3
This is the rate to use for comparing input streams. It is either Information rate or Stream rate. This applies to monitoring for Bit Rate alarming and monitoring of Redundant Pairs. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  RateComparisonTYPE  

apexSesContConfRedundThreshold 1.3.6.1.4.1.1166.1.31.9.1.1.4
This object is obsolete. Session Control Redundancy Threshold. This is the percent used to determine Fail Over from Primary to Secondary, and Switch Back from Secondary to Primary. If a value of zero is specified, Fail Over or Switch Back will not occur. Range is 0 to 100%. Primary Fail Over to Secondary: FailOver = (PrimaryRate) < (Threshold * SecondaryRate) The Primary must remain below the threshold for apexGbeConfInRedundMonitorPeriod. Secondary Switch Back to Primary: SwitchBack = (PrimaryRate) >= (Threshold * SecondaryRate) The Primary must remain at or above the threshold for apexGbeConfInRedundMonitorPeriod seconds. The APEX will delay Switch Back an additional apexGbeConfInRedundSwitchTime seconds. Switch Back will not occur when apexGbeConfInRedundAutoSwitchBack is 'disabled'. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

apexSesContConfInputPreEncryptCheck 1.3.6.1.4.1.1166.1.31.9.1.1.5
Session Control Pre-Encryption Checking. Indicates if the APEX is to check if the input service is pre-encrypted or clear. Pre-encrypted is determined by examining the input PMT for a CA ECM descriptor (any CA ECM descriptor). If pre-encrypted, setting this flag will cause the APEX to pass through ECM PID for this service. For input services that have a GI CA ECM descriptor, the APEX will also pass through the PIT message (extract and re-insert the PIT). The output PMT for pre-encrypted services will contain a CA ECM descriptor (referencing the ECM PID). When PID Remapping is enabled, pre-encryption for a service is only valid when the input ECM PID is on a different PID than the associated PMT PID. If this flag is set to pre-encryption and the input service is not pre-encrypted, then the setting of this flag has no affect on the output service. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexSesContConfRedundType 1.3.6.1.4.1.1166.1.31.9.1.1.6
The redundancy type for output streams in Session Control operating mode. - hotWarm indicates only 1 input stream, primary or secondary, is open at any one time. For multicast streams, primary will be joined initially. The secondary is joined after a failover (the primary will be dropped prior to joining the secondary). - hotHot indicates both the primary and secondary streams are opened at the same time. For multicast streams, both streams are joined immediately. Changes to the redundancy type cannot be made while there are active routes or sessions. All routes and sessions must be deleted prior to changing the redundancy type. Once written, a save must be performed via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER hotWarm(1), hotHot(2)  

apexSesContConfFollowDtcp 1.3.6.1.4.1.1166.1.31.9.1.1.7
Determines how the copy protection settings (CCI, APS, and CIT) within the PRK will be set. All outputs in Session Control (SDV) mode will use this setting for following input DTCP. Disabled - Use ERM Configuration settings if encryption blob provided. Use CTE settings when in CTE encryption mode and no ERM encryption blob provided. Enabled - Follow input DTCP Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexSesContConfTable 1.3.6.1.4.1.1166.1.31.9.1.2
This is a table of Session Control configuration parameters for each output transport stream. This table defines the primary and secondary Gigabit Ethernet interfaces for each output stream in Session Control operating mode. The primary and secondary interfaces cannot be changed for an output stream when there are active Session Control mappings. All Session Control mappings on an output stream must be removed prior to changing the primary or secondary interface settings. Once written, the change to this table will only take immediate effect after apexSesContConfTableApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexSesContConfTableApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexSesContConfEntry

apexSesContConfEntry 1.3.6.1.4.1.1166.1.31.9.1.2.1
Session Control Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexSesContConfEntry  

apexSesContConfOutputTsNum 1.3.6.1.4.1.1166.1.31.9.1.2.1.1
Output transport stream number (index).
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexSesContConfGbePrimaryInterface 1.3.6.1.4.1.1166.1.31.9.1.2.1.2
The primary Gbe interface for Session Control. Zero indicates not available. This parameter cannot be changed for any output stream if there is at least 1 active session control mapping. Not configurable for RTSP.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4  

apexSesContConfGbeSecondaryInterface 1.3.6.1.4.1.1166.1.31.9.1.2.1.3
The secondary Gbe interface for RPC SDV. Zero indicates not available. This parameter cannot be changed for any output stream if there is at least 1 active session control mapping. Secondary selection is restricted based on Primary as follows: - Primary 1 or 2: Secondary must be 1 or 2 - Primary 3 or 4: Secondary must be 3 or 4 Not configurable for RTSP.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4  

apexSesContStatProtocol 1.3.6.1.4.1.1166.1.31.9.2.1.1
The communication protocol in use for output streams in Session Control operating mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), rpc(1), rtsp(2), mha-ermi(3)  

apexRpcDataCarouselProgram 1.3.6.1.4.1.1166.1.31.9.3.1.1.1
Indicates which Input Program Number to use for the Data Carousel. The data carousel in SDV mode (RPC or RTSP) is on a fixed PMT PID along with a fixed component PID. In order to maintain these PID values, the APEX will check for a specific input service number defined by this parameter. This service mapping is assumed to be the Data Carousel mapping. The APEX will maintain the PMT PID value along with the component PID value. To facilitate this mapping, the Data Carousel input/output program number is configurable. - Data Carousel Service Number Default: 0xF38F (62351) The PMT PID and component PID will be determined by the APEX by analyzing the PAT and PMT based on the program number configured. A program number of zero (0) indicates that there is no data carousel. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexRpcReportAllSessions 1.3.6.1.4.1.1166.1.31.9.3.1.1.2
Session reporting mode. Indicates what sessions will be reported when the APEX is requested to report sessions to a manager. When 'enabled', the APEX will report all sessions. When 'disabled', the APEX will report only the sessions for the requesting manager. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexRpcDeviceName 1.3.6.1.4.1.1166.1.31.9.3.1.1.3
The device name of this APEX. This variable is only used to generate an XML configuration file via the EM. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

apexRpcDeviceType 1.3.6.1.4.1.1166.1.31.9.3.1.1.4
The device type string reported in XML configuration file. This variable is only used to generate an XML configuration file via the EM. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

apexRpcControlInterface 1.3.6.1.4.1.1166.1.31.9.3.1.1.5
The Enet interface that will be used to set the IP address attribute in the generated XML file. This variable is only used to generate an XML configuration file via the EM. Once written, the change to this parameter will only take immediate effect after apexRpcApplyChange is changed to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRpcApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EthernetInterfaceTYPE  

apexRpcNumShellSessions 1.3.6.1.4.1.1166.1.31.9.3.1.1.6
The number of shell sessions to be created on each channel marked for session control mode. This variable is only used to generate an XML configuration file via the EM. Once written, the change to this parameter will only take immediate effect after apexRpcApplyChange is changed to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRpcApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..32  

apexRpcAvgBandwidthEnable 1.3.6.1.4.1.1166.1.31.9.3.1.1.7
When enabled the APEX populates the sessionRate in the QuerySessionInfo Response message with groupRate divided by the number of sessionIds in the group. The value reported makes no distinction between bound and unbound sessions. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexRpcApplyChange 1.3.6.1.4.1.1166.1.31.9.3.1.1.8
The Apply for RPC Settings. This applies to apexRpcControlInterface, apexRpcNumShellSessions, apexRpcRfPortServiceGroup. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexRpcRfPortTable 1.3.6.1.4.1.1166.1.31.9.3.1.2
Table of Configuration data for RPC Session RF Ports. This variable is only used to generate an XML configuration file via the EM.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRpcRfPortEntry

apexRpcRfPortEntry 1.3.6.1.4.1.1166.1.31.9.3.1.2.1
RPC RF Port Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRpcRfPortEntry  

apexRpcRfPortNum 1.3.6.1.4.1.1166.1.31.9.3.1.2.1.1
The RF Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

apexRpcRfPortName 1.3.6.1.4.1.1166.1.31.9.3.1.2.1.2
The RF Port name. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

apexRpcRfPortServiceGroup 1.3.6.1.4.1.1166.1.31.9.3.1.2.1.3
The RF Port service group. Once written, the change to this parameter will only take immediate effect after apexRpcApplyChange is changed to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRpcApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..4294967295  

apexRpcRfChannelTable 1.3.6.1.4.1.1166.1.31.9.3.1.3
Table of Configuration data for RPC Session RF Channels. This variable is only used to generate an XML configuration file via the EM. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRpcRfChannelEntry

apexRpcRfChannelEntry 1.3.6.1.4.1.1166.1.31.9.3.1.3.1
RPC RF Channel Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRpcRfChannelEntry  

apexRpcRfChannelNum 1.3.6.1.4.1.1166.1.31.9.3.1.3.1.1
The RF Channel number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexRpcRfChannelName 1.3.6.1.4.1.1166.1.31.9.3.1.3.1.2
The name of this RF Channel.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

apexRpcSessionStatTable 1.3.6.1.4.1.1166.1.31.9.3.2.2
Table of RPC Switched Digital Video Session status. This table contains 1 row up to the maximum number of service mappings supported.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRpcSessionStatEntry

apexRpcSessionStatEntry 1.3.6.1.4.1.1166.1.31.9.3.2.2.1
RPC Switched Digital Video Session Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRpcSessionStatEntry  

apexRpcSessionStatIndex 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.1
The RPC Switched Digital Video Session Status table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexRpcSessionStatInputTsIndex 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.2
The index into the apexInputTsStatTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRpcSessionStatInputProgramNum 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.3
The Gigabit Ethernet Input Program Number. A value of zero (0) indicates that the input is an SPTS and the first program listed in the input PAT will be mapped by the APEX.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRpcSessionStatSourceIpAddr3 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.4
The Gigabit Ethernet IGMP v3 Source IP Address 3. This IP address is currently unsupported by the APEX.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexRpcSessionStatOutputQamChannel 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.5
The Output QAM Channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRpcSessionStatOutputProgramNum 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.6
The Output Program Number (1 - 65535).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRpcSessionStatProgramBandwidth 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.7
The Expected Program Bandwidth (bps). This is the bandwidth of the program as defined in the service mapping. A value of 0 indicates that the program BW is unknown.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRpcSessionStatSessionType 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.8
The Type of session (SDV binding or VOD/Broadcast session). 1 = Switched Digital Video (SDV) 2 = VOD or Broadcast
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noSession(0), sdv(1), vodOrBroadcast(2)  

apexRpcSessionStatSessionIdWord1 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.9
The Session ID Word 1. Session IDs are 10 byte character arrays. Session IDs are be stored as 3 4-byte words (3 ulongs) in this MIB. First 2 Bytes are always 0, next 10 contain the session ID. Session ID is broken up as follows: Word 1: 00:01 = 0x0000 (unused) Word 1: 02:03 = 1st 2 bytes of session ID (1st 2 bytes of MAC address) Word 2: 00:03 = Next 4 bytes (these 4 plus 1st 2 are the MAC address of manager) Word 3: 00:03 = Last 4 bytes (unique number assigned by manager)
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexRpcSessionStatSessionIdWord2 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.10
The Session ID Word 2. Session IDs are 10 byte character arrays. Session IDs are be stored as 3 4-byte words (3 Unsigned32) in this MIB. First 2 Bytes are always 0, next 10 contain the session ID. Session ID is broken up as follows: Word 1: 00:01 = 0x0000 (unused) Word 1: 02:03 = 1st bytes of session ID (1st 2 bytes of MAC address) Word 2: 00:03 = Next 4 bytes (these 4 plus 1st 2 are the MAC address of manager) Word 3: 00:03 = Last 4 bytes (unique number assigned by manager)
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexRpcSessionStatSessionIdWord3 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.11
The Session ID Word 3. Session IDs are 10 byte character arrays. Session IDs are be stored as 3 4-byte words (3 Unsigned32) in this MIB. First 2 Bytes are always 0, next 10 contain the session ID. Session ID is broken up as follows: Word 1: 00:01 = 0x0000 (unused) Word 1: 02:03 = 1st bytes of session ID (1st 2 bytes of MAC address) Word 2: 00:03 = Next 4 bytes (these 4 plus 1st 2 are the MAC address of manager) Word 3: 00:03 = Last 4 bytes (unique number assigned by manager)
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexRpcSessionStatManagerIpAddr 1.3.6.1.4.1.1166.1.31.9.3.2.2.1.12
The IP address of the RPC SDV, VOD, or Broadcast manager sending session commands.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexRpcQamStatTable 1.3.6.1.4.1.1166.1.31.9.3.2.3
Table of RPC Switched Digital Video QAM status. This table is indexed by output stream number and 48 rows.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRpcQamStatEntry

apexRpcQamStatEntry 1.3.6.1.4.1.1166.1.31.9.3.2.3.1
RPC Switched Digital Video QAM Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRpcQamStatEntry  

apexRpcQamStatQamChannelNum 1.3.6.1.4.1.1166.1.31.9.3.2.3.1.1
The RPC Switched Digital Video QAM Status table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexRpcQamStatNumSdvSessions 1.3.6.1.4.1.1166.1.31.9.3.2.3.1.2
The Number of reserved SDV sessions on this QAM Channel. This is the number of SDV sessions that have been reserved by the manager. Each SDV session requires that a manager reserve a QAM. This is the count of SDV sessions reserved (not the actual number of active SDV sessions).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRpcQamStatNumVodBcSessions 1.3.6.1.4.1.1166.1.31.9.3.2.3.1.3
The Number of VOD/Broadcast sessions on this QAM Channel. This is the number of VOD/Broadcast sessions active on a QAM Channel. Since VOD and Broadcast sessions are not required to be reserved for an output, this is the count of active VOD and Broadcast sessions on a specific QAM.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRpcQamStatSdvGroupBandwidth 1.3.6.1.4.1.1166.1.31.9.3.2.3.1.4
The Group BW for SDV sessions (not used for VOD/Broadcast sessions). This is the total amount of BW allocated for all SDV sessions on a channel. The total SDV BW for a channel is defined by the session manager. The manager reserves this BW for future SDV sessions. This is not the BW of current active SDV sessions, but the total BW reserved by the manager for SDV sessions.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexRtspReportGbeInterfaces 1.3.6.1.4.1.1166.1.31.9.4.1.1.1
This selects which pair of GBE interfaces are to be reported to the RTSP controller (ERM) via VREP. The pairedPortAssignment selection allows for both pairs of GBE interfaces to be reported to the ERM. This allows for all 4 GBE interfaces to be used by the ERM for session mappings. This effectively splits the APEX into 2x24 QAM devices where the first GBE interface pair (1&2) are assigned to the first 24 output QAM streams (output TS 1 - 24) and the second GBE pair (3&4) are assigned to the second 24 output QAM streams (output TS 25-48). Selecting reportGbe1and2 or reportGbe3and4 limits the ERM to 2 GBE interfaces only. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), reportGbe1and2(1), reportGbe3and4(2), pairedPortAssignment(3)  

apexRtspConfControllerApplyTable 1.3.6.1.4.1.1166.1.31.9.4.1.2
Table of Apply Change for the data for apexRtspConfControllerTable. A row of this table corresponds to a row in apexRtspConfControllerTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspConfControllerApplyEntry

apexRtspConfControllerApplyEntry 1.3.6.1.4.1.1166.1.31.9.4.1.2.1
RTSP Controller Configuration Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspConfControllerApplyEntry  

apexRtspConfControllerApplyNum 1.3.6.1.4.1.1166.1.31.9.4.1.2.1.1
The RTSP Session Controller number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexRtspConfControllerApplyChange 1.3.6.1.4.1.1166.1.31.9.4.1.2.1.2
The Apply for a row of data in apexRtspConfControllerTable and apexRtspConfControlNamesTable. A row in this table corresponds to the same row index in the apexRtspConfControllerTable and apexRtspConfControlNamesTable. This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the APEX. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexRtspConfControllerTable 1.3.6.1.4.1.1166.1.31.9.4.1.3
Table of RTSP configuration items configurable on a Controller basis. Once written, the change to this table will only take immediate effect after apexRtspConfControllerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfControllerApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspConfControllerEntry

apexRtspConfControllerEntry 1.3.6.1.4.1.1166.1.31.9.4.1.3.1
RTSP Controller Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspConfControllerEntry  

apexRtspConfControllerNum 1.3.6.1.4.1.1166.1.31.9.4.1.3.1.1
The Controller Number. APEX currently supports only one controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexRtspConfControllerIp 1.3.6.1.4.1.1166.1.31.9.4.1.3.1.2
The IP Address of the RTSP session controller.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexRtspConfControllerPort 1.3.6.1.4.1.1166.1.31.9.4.1.3.1.3
Port for the RTSP session controller.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1024..65535  

apexRtspConfControllerHoldTime 1.3.6.1.4.1.1166.1.31.9.4.1.3.1.4
The session hold time in seconds. If the APEX does not receive a keep session alive message from the controller in this time the APEX will close the session. The APEX will transmit keep session alive messages at one-third of this time. Zero indicates that the APEX should not send keep session alive messages.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 9..300  

apexRtspConfControllerBandwidthDelta 1.3.6.1.4.1.1166.1.31.9.4.1.3.1.5
The Bandwidth Delta, in kilobits per second (kbps), for sending an Update Message. Whenever a QAM Channel's output utilization changes by more than the bandwidth delta, the APEX will send a update message providing the current BW being utilized. Zero indicates that the APEX should not send update messages based on bandwidth changes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 50..100000  

apexRtspConfControlNamesTable 1.3.6.1.4.1.1166.1.31.9.4.1.4
Table of RTSP configuration items configurable on a Controller basis. Contains the control names. This table is a row-for-row index match to the apexRtspConfControllerTable. Once written, the change to this table will only take immediate effect after apexRtspConfControllerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfControllerApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspConfControlNamesEntry

apexRtspConfControlNamesEntry 1.3.6.1.4.1.1166.1.31.9.4.1.4.1
RTSP Controller Names Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspConfControlNamesEntry  

apexRtspConfControlNamesNum 1.3.6.1.4.1.1166.1.31.9.4.1.4.1.1
The Controller Number. APEX currently supports only one controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexRtspConfControlNamesStreamingZone 1.3.6.1.4.1.1166.1.31.9.4.1.4.1.2
The streaming zone that the APEX is a member of.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

apexRtspConfControlNamesDeviceName 1.3.6.1.4.1.1166.1.31.9.4.1.4.1.3
The device name of this APEX.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

apexRtspConfQamChannelApplyTable 1.3.6.1.4.1.1166.1.31.9.4.1.5
Table of Apply Change for the data for apexRtspConfQamChannelTable. A row of this table corresponds to a row in apexRtspConfQamChannelTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspConfQamChannelApplyEntry

apexRtspConfQamChannelApplyEntry 1.3.6.1.4.1.1166.1.31.9.4.1.5.1
RTSP QAM Configuration Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspConfQamChannelApplyEntry  

apexRtspConfQamChannelApplyNum 1.3.6.1.4.1.1166.1.31.9.4.1.5.1.1
The QAM Channel number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexRtspConfQamChannelApplyChange 1.3.6.1.4.1.1166.1.31.9.4.1.5.1.2
The Apply for a row of data in apexRtspConfQamChannelTable. A row in this table corresponds to the same row index in the apexRtspConfQamChannelTable. This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the APEX. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexRtspConfQamChannelTable 1.3.6.1.4.1.1166.1.31.9.4.1.6
Table of Configuration data for RTSP Session QAM Channels. Once written, the change to this table will only take immediate effect after apexRtspConfQamChannelApplyChange to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfQamChannelApplyChange , value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspConfQamChannelEntry

apexRtspConfQamChannelEntry 1.3.6.1.4.1.1166.1.31.9.4.1.6.1
RTSP QAM Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspConfQamChannelEntry  

apexRtspConfQamChannelNum 1.3.6.1.4.1.1166.1.31.9.4.1.6.1.1
The QAM Channel number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexRtspConfQamChannelGroupName 1.3.6.1.4.1.1166.1.31.9.4.1.6.1.2
The QAM Group Name that this QAM Channel is a member of.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

apexRtspConfGbeEdgeGroupTable 1.3.6.1.4.1.1166.1.31.9.4.1.7
Table of Configuration data for RTSP Session GigE Interfaces. Once written, the change to this table will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspConfGbeEdgeGroupEntry

apexRtspConfGbeEdgeGroupEntry 1.3.6.1.4.1.1166.1.31.9.4.1.7.1
RTSP GigE Edge Group Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspConfGbeEdgeGroupEntry  

apexRtspConfGbeEdgeGroupNum 1.3.6.1.4.1.1166.1.31.9.4.1.7.1.1
The GigE Edge Group Interface number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexRtspConfGbeEdgeGroupName 1.3.6.1.4.1.1166.1.31.9.4.1.7.1.2
The Name of this GigE Interface.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

apexRtspConfMhaTable 1.3.6.1.4.1.1166.1.31.9.4.1.8
Table of MHA RTSP configuration items configurable on a Controller basis. Once written, the change to this table will only take immediate effect after apexRtspConfControllerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfControllerApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspConfMhaEntry

apexRtspConfMhaEntry 1.3.6.1.4.1.1166.1.31.9.4.1.8.1
MHA RTSP Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspConfMhaEntry  

apexRtspConfMhaNum 1.3.6.1.4.1.1166.1.31.9.4.1.8.1.1
The MHA Controller Number. APEX currently supports only one controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexRtspConfMhaAddressDomain 1.3.6.1.4.1.1166.1.31.9.4.1.8.1.2
Address Domain of the sender used in ERRP. Address Domain of the ERM and APEX must match in order to establish an ERRP connection. Zero is used as the global address domain, which is interpreted to mean that any advertised address can be reached from any address domain.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

apexRtspConfMhaPort 1.3.6.1.4.1.1166.1.31.9.4.1.8.1.3
Port for the MHA session controller.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1024..65535  

apexRtspConfMhaUdpMapEnable 1.3.6.1.4.1.1166.1.31.9.4.1.9.1
Indicates if the UDP Map is populated in the Update message sent by the APEX to the ERM when in MHA mode. When 'enabled', the APEX will report UDP ports available. When 'disabled', the APEX will include the UDP Map field but will not populate it with data. Once written, the change to this table will only take immediate effect after apexRtspConfControllerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfControllerApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexRtspConfMhaSbeEncryptionMode 1.3.6.1.4.1.1166.1.31.9.4.1.10.1
This parameter is used to set the Session based Encryption Mode. It applies to all session based encryption sessions. - 'full' - The APEX will use Full encryption. - 'fwk' - The APEX will use Fixed Working Key (FWK) encryption. - 'fpk' - The APEX will use Fixed Program Key (FPK) encryption. The APEX will not attempt to get EMMs. Once written, the change to this parameter will only take immediate effect after apexRtspConfMhaSbeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfMhaSbeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER full(1), fwk(2), fpk(3)  

apexRtspConfMhaSbeCciLevel 1.3.6.1.4.1.1166.1.31.9.4.1.10.2
Copy Control Information (CCI) Level setting for session based PRK messages if CCI is not defined in the XML encryption blob. - notDefined - CCI is not defined, settop box applications can configure CCI - copyFreely - program can be copied - copyOnce - program can be copied once - copyNever - program can never be copied - noMoreCopies - Once written, the change to this parameter will only take immediate effect after apexRtspConfMhaSbeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfMhaSbeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notDefined(1), copyFreely(2), copyOnce(3), copyNever(4), noMoreCopies(5)  

apexRtspConfMhaSbeApsLevel 1.3.6.1.4.1.1166.1.31.9.4.1.10.3
Analog Protection System (APS) Level setting for session based PRK messages if APS is not defined in the XML encryption blob. Defines what copy protection encoding will be applied to the analog composite output by the settop box. - notDefined - analog protection is not defined, settop box applications can configure APS - off - no analog protection - splitBurstOff - AGC on, split burst off - splitBurst2Line - AGC on, 2 line split burst on - splitBurst4Line - AGC on, 4 line split burst on Once written, the change to this parameter will only take immediate effect after apexRtspConfMhaSbeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfMhaSbeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notDefined(1), off(2), splitBurstOff(3), splitBurst2Line(4), splitBurst4Line(5)  

apexRtspConfMhaSbeCitSetting 1.3.6.1.4.1.1166.1.31.9.4.1.10.4
Copy protection Constraint Image Trigger setting. This is only applicable when the session is being encrypted and the CIT setting was not contained in the XML encryption blob. Once written, the change to this parameter will only take immediate effect after apexRtspConfMhaSbeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexRtspConfMhaSbeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(sdv.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

apexRtspConfMhaSbeApplyChange 1.3.6.1.4.1.1166.1.31.9.4.1.10.5
The Apply for the MHA session based encryption settings. This parameter MUST be set to 'apply' in order for any of the data in MHA SBE to take effect in the APEX. This parameter MUST be set LAST after all other data in the MHA SBE has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexRtspSessionStatTable 1.3.6.1.4.1.1166.1.31.9.4.2.2
Table of RTSP Session status. This table contains 768 rows.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspSessionStatEntry

apexRtspSessionStatEntry 1.3.6.1.4.1.1166.1.31.9.4.2.2.1
RTSP Session Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspSessionStatEntry  

apexRtspSessionStatIndex 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.1
The RTSP Session Status table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexRtspSessionStatInputTsIndex 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.2
The index into the apexInputTsStatTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRtspSessionStatInputProgramNum 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.3
The Gigabit Ethernet Input Program Number. A value of zero (0) indicates that the input is an SPTS and the first program listed in the input PAT will be mapped by the APEX.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRtspSessionStatOutputQamChannel 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.4
The Output QAM Channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRtspSessionStatOutputProgramNum 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.5
The Output Program Number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRtspSessionStatProgramBandwidth 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.6
The Expected Program Bandwidth (bps). This is the bandwidth of the program as defined in the service mapping. A value of 0 indicates that the program BW is unknown.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRtspSessionStatManagerIpAddr 1.3.6.1.4.1.1166.1.31.9.4.2.2.1.7
The IP address of the manager sending session commands.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexRtspSessionIdTable 1.3.6.1.4.1.1166.1.31.9.4.2.3
Table of RTSP Session Ids. This table contains 768 rows and is a row-for-row index match to apexRtspSessionStatTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspSessionIdEntry

apexRtspSessionIdEntry 1.3.6.1.4.1.1166.1.31.9.4.2.3.1
RTSP Session ID Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspSessionIdEntry  

apexRtspSessionIdIndex 1.3.6.1.4.1.1166.1.31.9.4.2.3.1.1
The RTSP Session ID table index. This is a row-for-row match to the RTSP Session Status table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexRtspSessionId 1.3.6.1.4.1.1166.1.31.9.4.2.3.1.2
The Session ID.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

apexRtspQamStatTable 1.3.6.1.4.1.1166.1.31.9.4.2.4
Table of RTSP Session QAM status. This table is indexed by QAM channel number and contains 48 rows.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspQamStatEntry

apexRtspQamStatEntry 1.3.6.1.4.1.1166.1.31.9.4.2.4.1
RTSP Session QAM status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspQamStatEntry  

apexRtspQamStatQamChannelNum 1.3.6.1.4.1.1166.1.31.9.4.2.4.1.1
The RTSP Session Control Video QAM Status table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexRtspQamStatNumSessions 1.3.6.1.4.1.1166.1.31.9.4.2.4.1.2
The Number of active sessions on this QAM Channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRtspQamStatAllocatedBandwidth 1.3.6.1.4.1.1166.1.31.9.4.2.4.1.3
This is the total amount of BW allocated for all sessions on a channel.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexRtspStatControllerTable 1.3.6.1.4.1.1166.1.31.9.4.2.5
Table of RTSP status items configurable on a Controller basis.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspStatControllerEntry

apexRtspStatControllerEntry 1.3.6.1.4.1.1166.1.31.9.4.2.5.1
RTSP Controller Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspStatControllerEntry  

apexRtspStatControllerNum 1.3.6.1.4.1.1166.1.31.9.4.2.5.1.1
The Controller Number. APEX currently supports only one controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

apexRtspStatControllerDiscovery 1.3.6.1.4.1.1166.1.31.9.4.2.5.1.2
Status of Controller to APEX discovery.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notDiscovered(1), discovered(2), discoveredConnectionLost(3), discoveredAnotB(4), discoveredBnotA(5)  

apexRtspStatControllerConnection 1.3.6.1.4.1.1166.1.31.9.4.2.5.1.3
Status of the connection between the APEX and the Controller. 'notConnected' causes apexAlarmRtspControllerCommFault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notConnected(1), connected(2), connectedPort554(3), connectedPort2048(4)  

apexRtspStatControllerCommFault 1.3.6.1.4.1.1166.1.31.9.4.2.5.1.4
Current fault condition of apexRtspStatControllerConnection. This is the apexAlarmRtspControllerCommFault level for this controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexRtspStatQamChannelTable 1.3.6.1.4.1.1166.1.31.9.4.2.6
Table of Status data for RTSP Session QAM Channels.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspStatQamChannelEntry

apexRtspStatQamChannelEntry 1.3.6.1.4.1.1166.1.31.9.4.2.6.1
RTSP QAM Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspStatQamChannelEntry  

apexRtspStatQamChannelNum 1.3.6.1.4.1.1166.1.31.9.4.2.6.1.1
The QAM Channel number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexRtspStatQamChannelName 1.3.6.1.4.1.1166.1.31.9.4.2.6.1.2
The Name of this QAM Channel.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

apexRtspStatQamMptsModeTable 1.3.6.1.4.1.1166.1.31.9.4.2.7
Table of MPTS Mode Status data for RTSP Session QAM Channels.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspStatQamMptsModeEntry

apexRtspStatQamMptsModeEntry 1.3.6.1.4.1.1166.1.31.9.4.2.7.1
RTSP QAM MPTS Mode Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspStatQamMptsModeEntry  

apexRtspStatQamMptsModeQamChannelNum 1.3.6.1.4.1.1166.1.31.9.4.2.7.1.1
The QAM Channel number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexRtspStatQamMptsModeQamChannelMode 1.3.6.1.4.1.1166.1.31.9.4.2.7.1.2
The MPTS mode of this QAM Channel. The first session established on the QAM channel defines the MPTS mode. Each new session must have the same mode as long as one session is still active.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), passthrough(1), multiplexing(2)  

apexManualRouteRmdClear 1.3.6.1.4.1.1166.1.31.10.1.1.1
Clear all RMD information from DRAM and flash. Note that apexManualRouteEnable must be set to disabled for all rows before RMD information will be cleared by this parameter. If RMD information was cleared, the APEX will set this parameter to applyNotInProgressValidData. If RMD information was not cleared, the APEX will set this parameter to applyNotInProgressInvalidData. Once written, the change to this parameter will take effect immediately. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexManualRouteApplyTable 1.3.6.1.4.1.1166.1.31.10.1.2
Table of Apply Change for the data for Manual Route Table. A row in this table corresponds to the same row index in the Manual Route table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexManualRouteApplyEntry

apexManualRouteApplyEntry 1.3.6.1.4.1.1166.1.31.10.1.2.1
Manual Route Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexManualRouteApplyEntry  

apexManualRouteApplyIndex 1.3.6.1.4.1.1166.1.31.10.1.2.1.1
The index of the Manual Route Apply Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexManualRouteApplyChange 1.3.6.1.4.1.1166.1.31.10.1.2.1.2
The Apply for the row of data in the Manual Route Table. A row in this table corresponds to the same row index in the Manual Route table. This parameter MUST be set to 'apply' in order for any of the data in the Manual Route Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the Manual Route Table row has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexManualRouteTable 1.3.6.1.4.1.1166.1.31.10.1.3
Table of data for Manual Routes. Once written, the change to a row this table will only take immediate effect after the appropriate apexManualRouteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexManualRouteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexManualRouteEntry

apexManualRouteEntry 1.3.6.1.4.1.1166.1.31.10.1.3.1
Manual Route Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexManualRouteEntry  

apexManualRouteIndex 1.3.6.1.4.1.1166.1.31.10.1.3.1.1
The index of the Manual Route Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexManualRouteEnable 1.3.6.1.4.1.1166.1.31.10.1.3.1.2
Indicates that this Manual Route is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexManualRouteInputType 1.3.6.1.4.1.1166.1.31.10.1.3.1.3
Input Type of input from which to obtain data.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER gbe(1), fastEnet(2)  

apexManualRouteInputInterface 1.3.6.1.4.1.1166.1.31.10.1.3.1.4
Number of the input interface, of type configured by Input Type, from which to obtain data. Range: '0' = Not Applicable GBE = 1-4 FastEnet = 1-2
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4  

apexManualRouteInputUdp 1.3.6.1.4.1.1166.1.31.10.1.3.1.5
Input UDP Port from which to obtain data. Range: GBE = 0-65535 FastEnet = 1024-65535
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexManualRouteInputMulticastIp 1.3.6.1.4.1.1166.1.31.10.1.3.1.6
Input Multicast IP address from which to obtain data. An IP address of 0.0.0.0 indicates table entry not in use. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexManualRouteInputSourceIp 1.3.6.1.4.1.1166.1.31.10.1.3.1.7
Input IGMP v3 Source IP from which to obtain data. If the router supports IGMP v3 the GBE will only receive data from this source IP. If Source IP is not specified or the router does not support IGMP v3 the GBE will receive data from any source device. Source IP address must be a valid singlecast address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexManualRouteInputProgNum 1.3.6.1.4.1.1166.1.31.10.1.3.1.8
Input MPEG Program Number to multiplex. A value of 0 can be used as a wild card. This will cause the APEX to map the first program listed in the input PAT to the specified output (regardless of input program number). Input program number zero should only be used when mapping Single Program Transport Streams (SPTS).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexManualRouteInputPreEncryptCheck 1.3.6.1.4.1.1166.1.31.10.1.3.1.9
Manual Routing Pre-Encryption Checking. Indicates if the APEX is to check if the input service is pre-encrypted or clear. Pre-encrypted is determined by examining the input PMT for a CA ECM descriptor (any CA ECM descriptor). If pre-encrypted, setting this flag will cause the APEX to pass through ECM PID for this service. For input services that have a GI CA ECM descriptor, the APEX will also pass through the PIT message (extract and re-insert the PIT). The output PMT for pre-encrypted services will contain a CA ECM descriptor (referencing the ECM PID). When PID Remapping is enabled, pre-encryption for a service is only valid when the input ECM PID is on a different PID than the associated PMT PID. If this flag is set to pre-encryption and the input service is not pre-encrypted, then the setting of this flag has no affect on the output service.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexManualRouteOutputTsNum 1.3.6.1.4.1.1166.1.31.10.1.3.1.10
Output Transport Stream Number of the output on which to place data. Zero = NotApplicable and is only valid if the apexManualRouteTable entry is not being used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..48  

apexManualRouteOutputProgNum 1.3.6.1.4.1.1166.1.31.10.1.3.1.11
Output Program number to use for the program. Zero = NotApplicable and is only valid if the apexManualRouteTable entry is not being used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexManualRouteOutputEncryptMode 1.3.6.1.4.1.1166.1.31.10.1.3.1.12
Encryption Mode. Not supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clear(1)  

apexManualRouteOutputCopyProtectSource 1.3.6.1.4.1.1166.1.31.10.1.3.1.13
Copy Protection Source. Not supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER followInputDtcp(1), configuredSource(2)  

apexManualRouteSourceId 1.3.6.1.4.1.1166.1.31.10.1.3.1.14
Broadcast Encryption Source ID. Only applies to programs if the input type is Gbe and the output encryption mode is Broadcast Encryption. (apexOutputTsConfEncryptionType set to 'broadcastEncryption')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexManualRouteProviderId 1.3.6.1.4.1.1166.1.31.10.1.3.1.15
Broadcast Encryption Provider ID. Only applies to programs if the input type is Gbe and the output encryption mode is Broadcast Encryption. (apexOutputTsConfEncryptionType set to 'broadcastEncryption')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexManRtePassThroughApplyTable 1.3.6.1.4.1.1166.1.31.10.1.4
Table of Apply Change for the data for Manual Route Pass Through Table. A row in this table corresponds to the same row index in the Manual Route Pass Through table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexManRtePassThroughApplyEntry

apexManRtePassThroughApplyEntry 1.3.6.1.4.1.1166.1.31.10.1.4.1
Manual Route Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexManRtePassThroughApplyEntry  

apexManRtePassThroughApplyOutputTsNum 1.3.6.1.4.1.1166.1.31.10.1.4.1.1
The index of the Manual Route Pass Through Apply Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexManRtePassThroughApplyChange 1.3.6.1.4.1.1166.1.31.10.1.4.1.2
The Apply for the row of data in the Manual Route Pass Through Table. A row in this table corresponds to the same row index in the Manual Route Pass Through table. This parameter MUST be set to 'apply' in order for any of the data in the Manual Route Pass Through Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the Manual Route Pass Through Table row has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexManRtePassThroughTable 1.3.6.1.4.1.1166.1.31.10.1.5
Table of data for Manual Route Pass Through. This table is used to pass through an entire input stream to an output stream. Once written, the change to a row this table will only take immediate effect after the appropriate apexManRtePassThroughApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexManRtePassThroughApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexManRtePassThroughEntry

apexManRtePassThroughEntry 1.3.6.1.4.1.1166.1.31.10.1.5.1
Manual Route Pass Through Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexManRtePassThroughEntry  

apexManRtePassThroughOutputTsNum 1.3.6.1.4.1.1166.1.31.10.1.5.1.1
The index of the Manual Route Pass Through Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexManRtePassThroughEnable 1.3.6.1.4.1.1166.1.31.10.1.5.1.2
Indicates that this Manual Route Pass Through is enabled or disabled. An input stream can only be passed through to an output stream when there are no active service or PID mappings to the output stream.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexManRtePassThroughInputType 1.3.6.1.4.1.1166.1.31.10.1.5.1.3
Input Type of input from which to obtain data.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER gbe(1), fastEnet(2)  

apexManRtePassThroughInputInterface 1.3.6.1.4.1.1166.1.31.10.1.5.1.4
Number of the input interface, of type configured by Input Type, from which to obtain data. Range: '0' = Not Applicable GBE = 1-4 FastEnet = 1-2
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4  

apexManRtePassThroughInputUdp 1.3.6.1.4.1.1166.1.31.10.1.5.1.5
Input UDP Port from which to obtain data. Range: GBE = 0-65535 FastEnet = 1024-65535
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexManRtePassThroughInputMulticastIp 1.3.6.1.4.1.1166.1.31.10.1.5.1.6
Input Multicast IP address from which to obtain data. An IP address of 0.0.0.0 indicates table entry not in use. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexManRtePassThroughInputSourceIp 1.3.6.1.4.1.1166.1.31.10.1.5.1.7
Input IGMP v3 Source IP address from which to obtain data. If the router supports IGMP v3 the GBE will only receive data from this source IP. If Source IP is not specified or the router does not support IGMP v3 the GBE will receive data from any source device. Source IP address must be a valid singlecast address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexManRteGbeInRedApplyTable 1.3.6.1.4.1.1166.1.31.10.1.6.2
Table of Apply Change for the data for Manual Route Table. A row in this table corresponds to the same row index in the Manual Route table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexManRteGbeInRedApplyEntry

apexManRteGbeInRedApplyEntry 1.3.6.1.4.1.1166.1.31.10.1.6.2.1
Manual Routing Gbe Input Ts Configuration Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexManRteGbeInRedApplyEntry  

apexManRteGbeInRedApplyIndex 1.3.6.1.4.1.1166.1.31.10.1.6.2.1.1
The index of the Manual Routing Gbe Input Ts Configuration Apply Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexManRteGbeInRedApplyChange 1.3.6.1.4.1.1166.1.31.10.1.6.2.1.2
The Apply for the row of data in the Manual Routing Gbe Input Ts Configuration Table. A row in this table corresponds to the same row index in the Manual Routing Gbe Input Ts Configuration table. This parameter MUST be set to 'apply' in order for any of the data in the Manual Routing Gbe Input Ts Configuration Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the Manual Routing Gbe Input Ts Configuration Table row has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexManRteGbeInRedTable 1.3.6.1.4.1.1166.1.31.10.1.6.3
This table is the Manual Routing Gigabit Ethernet Input Transport Stream Configuration Table. This table contains 768 rows. For Force Switching a Redundancy pair for an Input TS configured in this table, refer to the same row index in apexManRteGbeInRedForceSwitchTable. Once written, the change to this table will only take immediate effect after apexManRteGbeInRedApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexManRteGbeInRedApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(gige_red.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexManRteGbeInRedEntry

apexManRteGbeInRedEntry 1.3.6.1.4.1.1166.1.31.10.1.6.3.1
Manual Routing Gigabit Ethernet Input Transport Stream Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexManRteGbeInRedEntry  

apexManRteGbeInRedIndex 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.1
The Manual Routing Gbe Input Ts Configuration table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexManRteGbeInRedPriInterface 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.2
The primary Gigabit Ethernet Interface. Zero indicates this row of the table is not in use.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4  

apexManRteGbeInRedPriUdp 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.3
The primary Gigabit Ethernet Input UDP Port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexManRteGbeInRedPriMulticastIp 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.4
The primary Multicast receive IP address. An IP address of 0.0.0.0 indicates table entry not in use. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexManRteGbeInRedPriSourceIp 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.5
This is the IP address of the source device for the primary interface. If the router supports IGMP v3 the GBE will only receive data from this source IP. If Source IP is not specified or the router does not support IGMP v3 the GBE will receive data from any source device. Source IP address must be a valid singlecast address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexManRteGbeInRedPriLowAlarmBitRate 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.6
This is the bit rate, in bits per second, below which the APEX will issue the apexAlarmGbeInputStreamLowBitRate alarm for the primary interface. The APEX will compare either the current Information rate or Stream rate as configured in apexManRteGbeInRedRateCompareType. Setting to zero disables the bit rate alarming. The APEX updates the bit rate statistics every five seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apexManRteGbeInRedPriHighAlarmBitRate 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.7
This is the bit rate, in bits per second, above which the APEX will issue the apexAlarmGbeInputStreamHighBitRate alarm for the primary interface. The APEX will compare either the current Information rate or Stream rate as configured in apexManRteGbeInRedRateCompareType. Setting to zero disables the bit rate alarming. The APEX updates the bit rate statistics every five seconds. Not supported.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apexManRteGbeInRedRateCompareType 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.8
This is the rate to use for comparing input streams. It is either Information rate or Stream rate. This applies to monitoring for Bit Rate alarming and monitoring of Redundant Pairs.
Status: current Access: read-write
OBJECT-TYPE    
  RateComparisonTYPE  

apexManRteGbeInRedEnable 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.9
This entry is used to enable Redundancy.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexManRteGbeInRedThreshold 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.10
Manual Routing Gigabit Ethernet Redundancy Threshold. This is the percent used to determine Fail Over from Primary to Secondary, and Switch Back from Secondary to Primary. If a value of zero is specified, Fail Over or Switch Back will not occur. Range is 0 to 100%. Primary Fail Over to Secondary: FailOver = (PrimaryRate) < (Threshold * SecondaryRate) The Primary must remain below the threshold for apexGbeConfInRedundMonitorPeriod. Fail Over will not occur when apexManRteGbeInRedSuspend is set to 'suspended'. Secondary Switch Back to Primary: SwitchBack = (PrimaryRate) >= (Threshold * SecondaryRate) The Primary must remain at or above the threshold for apexGbeConfInRedundMonitorPeriod seconds. The APEX will delay Switch Back an additional apexGbeConfInRedundSwitchTime seconds. Switch Back will not occur when apexManRteGbeInRedSuspend is set to 'suspended' or apexGbeConfInRedundAutoSwitchBack is 'disabled'.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

apexManRteGbeInRedSuspend 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.11
This suspends Redundant Pair switching when set to 'suspended'. This has no effect when redundancy is disabled. Forced switching of Redundant Pairs is not prevented when this is set to 'suspended'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSuspended(1), suspended(2)  

apexManRteGbeInRedSecInterface 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.12
The secondary Gigabit Ethernet Interface for redundancy. Zero is invalid when redundancy is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4  

apexManRteGbeInRedSecUdp 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.13
The secondary Gigabit Ethernet Input UDP Port for redundancy.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexManRteGbeInRedSecMulticastIp 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.14
The secondary Multicast receive IP address for redundancy. An IP address of 0.0.0.0 indicates singlecast only. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexManRteGbeInRedSecSourceIp 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.15
This is the IP address of the source device for the secondary interface. If the router supports IGMP v3 the GBE will only receive data from this source IP. If Source IP is not specified or the router does not support IGMP v3 the GBE will receive data from any source device. Source IP address must be a valid singlecast address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexManRteGbeInRedSecLowAlarmBitRate 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.16
This is the bit rate, in bits per second, below which the APEX will issue the apexAlarmGbeInputStreamLowBitRate alarm for the secondary interface. The APEX will compare either the current Information rate or Stream rate as configured in apexManRteGbeInRedRateCompareType. Setting to zero disables the bit rate alarming. The APEX updates the bit rate statistics every five seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apexManRteGbeInRedSecHighAlarmBitRate 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.17
This is the bit rate, in bits per second, above which the APEX will issue the apexAlarmGbeInputStreamHighBitRate alarm for the secondary interface. The APEX will compare either the current Information rate or Stream rate as configured in apexManRteGbeInRedRateCompareType. Setting to zero disables the bit rate alarming. The APEX updates the bit rate statistics every five seconds. Not supported.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apexManRteGbeInRedSecRedundMcJoin 1.3.6.1.4.1.1166.1.31.10.1.6.3.1.18
This is not currently supported and is reserved for future use.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noJoinOnOpen(1), joinOnOpen(2)  

apexManRteGbeInRedForceSwitchTable 1.3.6.1.4.1.1166.1.31.10.1.6.4
This table is the Manual Routing Gigabit Ethernet Input Transport Stream Redundancy Configuration Table. This table contains 768 rows. A row in this table corresponds to the same index in the apexManRteGbeInRedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexManRteGbeInRedForceSwitchEntry

apexManRteGbeInRedForceSwitchEntry 1.3.6.1.4.1.1166.1.31.10.1.6.4.1
Gigabit Ethernet Input Stream Redundancy Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexManRteGbeInRedForceSwitchEntry  

apexManRteGbeInRedForceSwitchIndex 1.3.6.1.4.1.1166.1.31.10.1.6.4.1.1
The Manual Routing Gbe Input Ts Redundancy Configuration table index. A row in this table corresponds to the same index in the apexManRteGbeInRedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexManRteGbeInRedForceSwitch 1.3.6.1.4.1.1166.1.31.10.1.6.4.1.2
The Gigabit Ethernet Redundant Pair force switch. This will have no effect if the corresponding row setting of apexManRteGbeInRedEnable is 'disabled'. The corresponding row setting apexManRteGbeInRedSuspend is ignored when 'forceSwitch' is set. The switch will occur even if apexManRteGbeInRedSuspend is 'suspended'. When forced to the Secondary of the pair, the APEX will stay on the Secondary until the user forces back to the Primary. The APEX will not automatically switch back to the Primary when the Primary is restored above the failover threshold. The APEX will not allow a force to the Primary unless the Primary is above the failover threshold. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER switchNotInProgress(1), forceSwitch(2)  

apexManualRouteInvalidApplyText 1.3.6.1.4.1.1166.1.31.10.2.1.1
When apexManualRouteApplyChange is set to applyNotInProgressInvalidData this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a table entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexManRtePassThroughInvalidApplyText 1.3.6.1.4.1.1166.1.31.10.2.1.2
When apexManRtePassThroughApplyChange is set to applyNotInProgressInvalidData this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a table entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexManRteGbeInRedInvalidApplyText 1.3.6.1.4.1.1166.1.31.10.2.1.3
When apexManRteGbeInRedTableApplyChange is set to applyNotInProgressInvalidData this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a table entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexManRteGbeInRedStatusMapTable 1.3.6.1.4.1.1166.1.31.10.2.2.2
This table provides the mapping between the indexes in Manual Routing Gigabit Ethernet Input Transport Stream Redundancy Configuration and Input TS Status. This table contains 768 rows. The index in this table corresponds to the same index in the apexManRteGbeInRedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexManRteGbeInRedStatusMapEntry

apexManRteGbeInRedStatusMapEntry 1.3.6.1.4.1.1166.1.31.10.2.2.2.1
Gigabit Ethernet Input Stream Redundancy Configuration and Status Mapping Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexManRteGbeInRedStatusMapEntry  

apexManRteGbeInRedStatusMapIndex 1.3.6.1.4.1.1166.1.31.10.2.2.2.1.1
The Manual Routing Gbe Input Ts Redundancy Configuration and status mapping table index. A index in this table corresponds to the same index in the apexManRteGbeInRedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexManRteGbeInRedStatusMapInputTsStatRow 1.3.6.1.4.1.1166.1.31.10.2.2.2.1.2
The Manual Routing Gbe Input TS Status index. This provides the mapping between the entries in apexManRteGbeInRedTable and apexInputTsStatTable. The range of the index is 0 - 784, where 0 indicates no direct association between configuration and status and the 1-784 is the actual Input Stream status row (relative 1). @Config(config=no, reboot=no)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..784  

apexPidMapApplyTable 1.3.6.1.4.1.1166.1.31.11.1.2
Table of Apply Change for the data for PID Map Table. A row in this table corresponds to the same row index in the PID Map table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexPidMapApplyEntry

apexPidMapApplyEntry 1.3.6.1.4.1.1166.1.31.11.1.2.1
PID Map Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexPidMapApplyEntry  

apexPidMapApplyIndex 1.3.6.1.4.1.1166.1.31.11.1.2.1.1
The index of the PID Map Apply Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..480  

apexPidMapApplyChange 1.3.6.1.4.1.1166.1.31.11.1.2.1.2
The Apply for the row of data in the PID Map Table. A row in this table corresponds to the same row index in the PID Map table. This parameter MUST be set to 'apply' in order for any of the data in the PID Map Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the PID Map Table row has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexPidMapTable 1.3.6.1.4.1.1166.1.31.11.1.1
Table of data for Ancillary Pid Mapping. There are 480 rows in this table (APEX supports up to 480 ancillary PID mappings). Once written, the change to this table will only take immediate effect after apexPidMapApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexPidMapApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexPidMapEntry

apexPidMapEntry 1.3.6.1.4.1.1166.1.31.11.1.1.1
Pid Mapping Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexPidMapEntry  

apexPidMapIndex 1.3.6.1.4.1.1166.1.31.11.1.1.1.1
Index of Pid Mapping Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..480  

apexPidMapEnable 1.3.6.1.4.1.1166.1.31.11.1.1.1.2
Indicates whether this PID Mapping is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexPidMapInputType 1.3.6.1.4.1.1166.1.31.11.1.1.1.3
Input Type of input from which to obtain data.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER gbe(1), fastEnet(2)  

apexPidMapInputInterface 1.3.6.1.4.1.1166.1.31.11.1.1.1.4
Number of the input, of type configured by Input Type, from which to obtain data. Range: '0' = Not Applicable GBE = 1-4 FastEnet = 1-2
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4  

apexPidMapInputUdp 1.3.6.1.4.1.1166.1.31.11.1.1.1.5
Input UDP Port from which to obtain data. Range: GBE = 0-65535 FastEnet = 1024-65535
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexPidMapInputMulticastIp 1.3.6.1.4.1.1166.1.31.11.1.1.1.6
The Multicast receive IP address on which to receive data. An IP address of 0.0.0.0 indicates singlecast only. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexPidMapInputSourceIp 1.3.6.1.4.1.1166.1.31.11.1.1.1.7
This is the IP address of the source device. If the router supports IGMP v3 the GBE will only receive data from this source IP. If Source IP is not specified or the router does not support IGMP v3 the GBE will receive data from any source device. Source IP address must be a valid singlecast address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexPidMapInputPid 1.3.6.1.4.1.1166.1.31.11.1.1.1.8
Input MPEG PID to multiplex. When PID Remapping for an output is enabled, the input PID value and output PID value can be different. When PID Remapping for an output is disabled, the input and output PIDs must be the same. Input PID 0 (PAT PID) cannot be mapped by the user.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..8191  

apexPidMapOutputTsNum 1.3.6.1.4.1.1166.1.31.11.1.1.1.9
Output Transport Stream Number of the output on which to place data. Zero is only valid if the apexPidMapTable entry is not being used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..48  

apexPidMapOutputPid 1.3.6.1.4.1.1166.1.31.11.1.1.1.10
Output PID to use for the data. This output PID value must match the input PID value when PID Remapping for the output stream is disabled. Zero is only valid if the apexPidMapTable entry is not being used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..8191  

apexPidMapMaxPidMappings 1.3.6.1.4.1.1166.1.31.11.2.1.1
Maximum number of Ancillary PID mappings supported.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexPidMapInvalidApplyText 1.3.6.1.4.1.1166.1.31.11.2.1.3
When apexPidMapApplyChange is set to applyNotInProgressInvalidData this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a table entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexInsertionMode 1.3.6.1.4.1.1166.1.31.12.1.1.1
This parameter is used to set the insertion mode for the APEX. The APEX may be configured to insert messages as efficiently as possible (efficient) or restrict insertion to a single section starting per packet (singleSection). Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER efficient(1), singleSection(2)  

apexInsertPacketStatisticsTable 1.3.6.1.4.1.1166.1.31.12.2.2
Table of Output Transport Stream Insert Packet Statistics. Indexed by Output Transport Stream number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexInsertPacketStatisticsEntry

apexInsertPacketStatisticsEntry 1.3.6.1.4.1.1166.1.31.12.2.2.1
A row in the Output Transport Stream Insert Packet Statistics table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexInsertPacketStatisticsEntry  

apexInsertPacketStatOutputTsNum 1.3.6.1.4.1.1166.1.31.12.2.2.1.1
Output Transport Stream Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexInsertPacketStatTotPkts 1.3.6.1.4.1.1166.1.31.12.2.2.1.2
Total number of packets inserted.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexInsertPacketStatNumPkts 1.3.6.1.4.1.1166.1.31.12.2.2.1.3
Number of packets inserted during the last monitoring period (currently 5 seconds).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexInputTsStatTable 1.3.6.1.4.1.1166.1.31.13.2.2
Table of Input Transport Stream Status data. For each input stream in use, an entry in this row will be utilized. This table will indicate the input stream in use by type, interface, UDP, multicast IP, and Source IP address. This table will also indicate if the input stream is a Primary or Secondary input stream. Table of 768 GigE entries plus 16 Host entries (784 total input entries). List of GigE and Host Ethernet input streams currently in use. Each row contains an entry for Primary and Secondary information along with the 1 currently in use.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexInputTsStatEntry

apexInputTsStatEntry 1.3.6.1.4.1.1166.1.31.13.2.2.1
Input Transport Stream Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexInputTsStatEntry  

apexInputTsStatIndex 1.3.6.1.4.1.1166.1.31.13.2.2.1.1
Index of Input Transport Stream Status Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..784  

apexInputTsStatStreamInUse 1.3.6.1.4.1.1166.1.31.13.2.2.1.2
Indicates whether the primary or secondary is in use. Zero indicates this row is not in use.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), primary(1), secondary(2)  

apexInputTsStatInputType 1.3.6.1.4.1.1166.1.31.13.2.2.1.3
Input Type of both primary and secondary inputs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), gbe(1), fastEnet(2)  

apexInputTsStatRoutingType 1.3.6.1.4.1.1166.1.31.13.2.2.1.4
Routing Type of both primary and secondary inputs. 'session' - applies to SDV session routes (RPC, RTSP). 'manual' - applies to all manual routes (Manual Routing, PID Mapping, and stream pass through). 'udpMapping - applies to UDP Port Mapping routes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), session(1), manual(2), udpMapping(3)  

apexInputTsStatPriState 1.3.6.1.4.1.1166.1.31.13.2.2.1.5
The current state of the primary Gigabit Ethernet Input TS configured in apexManRteGbeInRedTable. States are: closed (0) - Input TS is closed or table row is not in use. openedInUse (1) - Input TS is opened and in use. openedBackup (2) - Input TS is opened as backup only. openedTransToBackup (3) - Input TS is opened, transitioning to backup state. openedTransToInUse (4) - Input TS is opened, transitioning to in use state. The states of 'openedBackup', 'openedTransToBackup', and 'openedTransToBackup' apply only to Redundant Pairs. The state of 'openedBackup' applies to the Input TS of the pair that is not currently in use. The state of 'openedTransToBackup' applies to the Input TS of the pair that is currently in use but is transitioning to be the backup, as when a Fail Over or Switch Back is occurring. The state of 'openedTransToInUse' applies to the Input TS of the pair that is currently the backup use but is transitioning to be the in use, as when a Fail Over or Switch Back is occurring.
Status: current Access: read-only
OBJECT-TYPE    
  InputTsStateTYPE  

apexInputTsStatPriInputInterface 1.3.6.1.4.1.1166.1.31.13.2.2.1.6
Number of the primary input interface of type Input Type.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexInputTsStatPriInputUdp 1.3.6.1.4.1.1166.1.31.13.2.2.1.7
Input UDP Port for primary input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexInputTsStatPriInputMulticastIp 1.3.6.1.4.1.1166.1.31.13.2.2.1.8
The Multicast receive IP address for primary input.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexInputTsStatPriInputSourceIp 1.3.6.1.4.1.1166.1.31.13.2.2.1.9
This is the IGMP v3 Source IP address of the source device for the primary input.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexInputTsStatSecState 1.3.6.1.4.1.1166.1.31.13.2.2.1.10
The current state of the secondary Gigabit Ethernet Input TS configured in apexManRteGbeInRedTable. States are: closed (0) - Input TS is closed or table row is not in use. openedInUse (1) - Input TS is opened and in use. openedBackup (2) - Input TS is opened as backup only. openedTransToBackup (3) - Input TS is opened, transitioning to backup state. openedTransToInUse (4) - Input TS is opened, transitioning to in use state. The states of 'openedBackup', 'openedTransToBackup', and 'openedTransToBackup' apply only to Redundant Pairs. The state of 'openedBackup' applies to the Input TS of the pair that is not currently in use. The state of 'openedTransToBackup' applies to the Input TS of the pair that is currently in use but is transitioning to be the backup, as when a Fail Over or Switch Back is occurring. The state of 'openedTransToInUse' applies to the Input TS of the pair that is currently the backup use but is transitioning to be the in use, as when a Fail Over or Switch Back is occurring.
Status: current Access: read-only
OBJECT-TYPE    
  InputTsStateTYPE  

apexInputTsStatSecInputInterface 1.3.6.1.4.1.1166.1.31.13.2.2.1.11
Number of the secondary input interface of type Input Type.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexInputTsStatSecInputUdp 1.3.6.1.4.1.1166.1.31.13.2.2.1.12
Input UDP Port for secondary input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexInputTsStatSecInputMulticastIp 1.3.6.1.4.1.1166.1.31.13.2.2.1.13
The Multicast receive IP address for secondary input.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexInputTsStatSecInputSourceIp 1.3.6.1.4.1.1166.1.31.13.2.2.1.14
This is the IGMP v3 Source IP address of the source device for the secondary input.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexInputTsStatRateCompareType 1.3.6.1.4.1.1166.1.31.13.2.2.1.15
This is the rate in use for comparing input streams. It is either Information rate or Stream rate. This applies to monitoring for Bit Rate alarming and monitoring of Redundant Pairs.
Status: current Access: read-only
OBJECT-TYPE    
  RateComparisonTYPE  

apexOutputTsUtilMonAlarmThreshold 1.3.6.1.4.1.1166.1.31.14.1.4.1.1
The threshold, in percent, used to produce the apexAlarmOutputUtilizationFault alarm 'minor' while monitoring Output Transport Stream Bandwidth Utilization. An alarm of 'minor' will occur when this threshold is met or exceeded for apexOutputTsUtilMonSetAlarmDelay. The alarm will clear after remaining below this threshold for apexOutputTsUtilMonClearAlarmDelay. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

apexOutputTsUtilMonSetAlarmDelay 1.3.6.1.4.1.1166.1.31.14.1.4.1.2
This is the time in seconds that the Output Transport Stream must be at or exceeding apexOutputTsUtilMonAlarmThreshold before setting the apexAlarmOutputUtilizationFault alarm. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..900  

apexOutputTsUtilMonClearAlarmDelay 1.3.6.1.4.1.1166.1.31.14.1.4.1.3
This is the time in seconds that the Output Transport Stream must be below apexOutputTsUtilMonAlarmThreshold before clearing the apexAlarmOutputUtilizationFault alarm. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..900  

apexOutputTsUtilizationMonitorTable 1.3.6.1.4.1.1166.1.31.14.1.4.2
This is a table of configuration parameters for Rate Monitoring of the Output Transport Stream Bandwidth Utilization. Utilization information is accessed via apexOutputTsUtilizationTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexOutputTsUtilizationMonitorEntry

apexOutputTsUtilizationMonitorEntry 1.3.6.1.4.1.1166.1.31.14.1.4.2.1
Output Transport Rate Monitoring Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexOutputTsUtilizationMonitorEntry  

apexOutputTsUtilMonOutputTsNum 1.3.6.1.4.1.1166.1.31.14.1.4.2.1.1
Output Transport Stream Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexOutputTsUtilMonResetTotDropPacket 1.3.6.1.4.1.1166.1.31.14.1.4.2.1.2
Output Ts Reset total dropped packets. Setting to 'reset' resets same apexOutputTsUtilizTotalDropPackets index row in apexOutputTsUtilizationTable. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ResetStatisticsTYPE  

apexOutputTsConfApplyTable 1.3.6.1.4.1.1166.1.31.14.1.5
Table of Apply Change for Output Ts Config Table. This apply is only used for apexOutputTsConfOperatingMode, apexOutputTsConfEncryptionType, and apexOutputTsConfSimulcryptMode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexOutputTsConfApplyEntry

apexOutputTsConfApplyEntry 1.3.6.1.4.1.1166.1.31.14.1.5.1
Output Transport Stream Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexOutputTsConfApplyEntry  

apexOutputTsConfApplyIndex 1.3.6.1.4.1.1166.1.31.14.1.5.1.1
Index of Output Transport Stream Apply Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexOutputTsConfApplyChange 1.3.6.1.4.1.1166.1.31.14.1.5.1.2
The apply for Output Ts Config Table. This apply is only used for apexOutputTsConfOperatingMode, apexOutputTsConfEncryptionType, and apexOutputTsConfSimulcryptMode. A row in this table corresponds to the same row index in the Output Ts Config table. This parameter MUST be set to 'apply' in order for the items listed above to take effect in the APEX. This parameter MUST be set LAST after the relevant data in the Output Ts Config row has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexOutputTsConfigTable 1.3.6.1.4.1.1166.1.31.14.1.6
This is a table of configuration parameters for Output Transport Streams. Once written, a change to apexOutputTsConfEncryptionType, apexOutputTsConfOperatingMode, or apexOutputTsConfSimulcryptMode will only take immediate effect after the appropriate apexOutputTsConfApplyChange is set to 'apply'. All other changes to this table will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexOutputTsConfigEntry

apexOutputTsConfigEntry 1.3.6.1.4.1.1166.1.31.14.1.6.1
Output Transport Stream Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexOutputTsConfigEntry  

apexOutputTsConfOutputTsNum 1.3.6.1.4.1.1166.1.31.14.1.6.1.1
Output Transport Stream Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexOutputTsConfPidRemappingMode 1.3.6.1.4.1.1166.1.31.14.1.6.1.2
The PID Remapping mode setting. When 'disabled', the output PIDs for all services and ancillary PIDs are the same as the input PID values. This scheme can only be used when either mapping an entire MPTS to a QAM output or when SPTS are mapped and the user has already ensured that all of the PIDs across all inputs mapped to the same output stream are unique. When 'remapWithoutReuse', the APEX will determine the output PIDs from a predetermined range of PIDs for services and ancillary PIDs. The APEX will use a scheme to limit the reuse of service PIDs for each service mapping. This scheme MUST be used for outputs in Session Control mode and in normally in UDP Port Mapping mode (exception noted below). When receiving SPTS inputs, in order to ensure there are no PID conflicts, this scheme should be selected. When 'remapProgramBased', the APEX will determine the output PIDs from a predetermined range of PIDs for services and ancillary PIDs. The APEX uses a scheme to select the PMT PID based on the program number. The PMT PID is calculated as follows: (Program Number + 1) * 16. The component PIDs are sequential after the PMT PID. This scheme only allows for a total of 15 component PIDs per program. Output program numbers are also limited (1-256). This scheme is intended to be used when in UDP Port Mapping mode at specific sites. When 'unrestricted', the APEX will allocate output PIDs as long as they are needed using the whole available PIDs range, unlike other pid-remapping modes where PID values are internally pre-allocated for different uses (PMT, components, ECM, ...). This scheme is only recommended for cases when the user need a special pre-assigned EMM pid that can't be configured in the other pid-remapping modes. PID Remapping mode changes can only occur when the output is not in use (no service, PID, or stream mapping active to the output).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), remapWithoutReuse(2), remapProgramBased(3), remapProgramBased2(4), unrestricted(5)  

apexOutputTsConfOperatingMode 1.3.6.1.4.1.1166.1.31.14.1.6.1.3
This parameter is used to set the operating mode of the output. Operating mode changes can only occur when the output is not in use (no service, PID, or stream mapping active to the output). Session Control - User must select either RTSP or RPC to communicate with external resource manager. All service mappings on output are controlled by the external manager. - Only valid when Encryption Type is set to CTE or None - Only valid when Simulcrypt Mode is set to None - PID Remapping mode should be Enabled (Without Reuse) Manual Routing - User manually maps each service - Encryption Type can be any valid setting (none, CTE, or Broadcast) - Simulcrypt Mode must be None or External EIS UDP Port Mapping - Standard UDP Port Mapping for use with VOD servers. Uses specific algorithm based on UDP Port to determine output program mappings. - Encryption Type must be None or CTE (broadcast not supported) - Simulcrypt Mode must be None or External EIS Operating mode changes can only occur when the output is not in use (no service, PID, or stream mapping active to the output). @Commit(param=apexOutputTsConfApplyChange, value=2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notInUse(0), sessionControl(1), manualRouting(2), udpMapping(3), depi(4)  

apexOutputTsConfOutPatTsId 1.3.6.1.4.1.1166.1.31.14.1.6.1.4
Output Transport Stream ID to use for the output PAT in this Output Transport Stream. Changes to the output PAT TS ID can be made at any time and will cause the output PAT to automatically be updated to reflect the new TS ID setting.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexOutputTsConfPsipEnable 1.3.6.1.4.1.1166.1.31.14.1.6.1.5
This parameter indicates that PSIP is enabled for the Output Transport Stream.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexOutputTsConfEncryptionType 1.3.6.1.4.1.1166.1.31.14.1.6.1.6
This parameter is used to set the encryption type of the output. 'noEncryption' - All services are output in the clear 'cte' - Services on output use Common Tier Encryption. CTE parameters determine encryption mode, copy protection, and tiers. All services in CTE mode use the exact same configuration settings. - Valid for all operating modes - Simulcrypt Mode must be set to None 'broadcastEncryption' - Services on output use Broadcast Encryption. Requires connection to RDS (DAC) to get EMMs and Rights Meta Data (tiers, encryption mode, and copy protection settings) for each individual service. - Only valid when Operating Mode is Manual Routing. - Simulcrypt Mode must be set to None @Commit(param=apexOutputTsConfApplyChange, value=2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noEncryption(0), cte(1), broadcastEncryption(2)  

apexOutputTsConfSimulcryptMode 1.3.6.1.4.1.1166.1.31.14.1.6.1.7
This parameter is used to set the Simulcrypt mode of the output. The actual behavior is disable/enable (none/externalEIS). It can be set to externalEIS if the Encryption Algorithm is set to 'dvb-csa-simulcrypt and the Operating Mode is set to 'ManualRouting' or 'udpMapping'. It only can be none if there are no SCGs provisioned on that output TS. 'none' - Used for normal Mediacypher only encryption (CTE or Broadcast Encryption). 'externalEIS' - Used to indicate an external EIS can control the encryption of all services on the output. - Only valid when: - Operating Mode is set to 'ManualRouting' or 'udpMapping' - Encryption Algorithm is set to 'dvb-csa-simulcrypt' 'internalEIS' - Not supported at this time and is invalid to select. @Commit(param=apexOutputTsConfApplyChange, value=2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), externalEIS(1), internalEIS(2)  

apexOutputTsConfPcrLess 1.3.6.1.4.1.1166.1.31.14.1.6.1.8
This parameter indicates that PCR-less is enabled for the Output Transport Stream.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexOutputTsStatusInvalidApplyText 1.3.6.1.4.1.1166.1.31.14.2.1.1
When apexOutputTsConfApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexOutputTsUtilizationSamplePeriod 1.3.6.1.4.1.1166.1.31.14.2.2.1.1
Sample Period for Output Transport Stream Bandwidth Utilization Rate Monitoring. This parameter indicates the length of time in milliseconds the stream is monitored during a single sample. This can be used with apexOutputTsUtilizNumSamples to determine the amount of time or percent of time the stream was monitored during a fifteen minute sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsUtilizationTable 1.3.6.1.4.1.1166.1.31.14.2.2.2
This is a table of status parameters containing bandwidth utilization for Output Transport Streams. The sampling interval is up to fifteen minutes. There is a rolling average as well as last sample, peak, and minimum information. There is overflow information and dropped packet counts. This table is indexed by Output Transport Stream Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexOutputTsUtilizationEntry

apexOutputTsUtilizationEntry 1.3.6.1.4.1.1166.1.31.14.2.2.2.1
Output Transport Stream Bandwidth Utilization Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexOutputTsUtilizationEntry  

apexOutputTsUtilizOutpuTsNum 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.1
Output Transport Stream Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexOutputTsUtilizDataFlag 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.2
Flag to indicate whether the Output Transport Stream was monitored a full fifteen minute sampling interval and a complete set of samples was obtained. 'samplingComplete' - indicates sampling complete with good samples. 'samplingIncomplete' - indicates incomplete sampling due to APEX startup or OTS rate changed during the period.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), samplingComplete(1), samplingIncomplete(2)  

apexOutputTsUtilizNumSamples 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.3
Number of samples included in the data. This can be used with apexOutputTsUtilizationSamplePeriod to determine the amount of time or percent of time the stream was monitored during the sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOutputTsUtilizThreshold 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.4
Indicates whether there is a utilization error has occurred. The error occurs when Output Utilization Alarm Threshold has been reached for Output Utilization Set Alarm Delay seconds and will clear after the output is below the Output Utilization Alarm Threshold for Output Utilization Clear Alarm Delay. This field is also cleared when the QAM output is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), noError(1), alarmThresholdReached(2)  

apexOutputTsUtilizTime 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.5
Time in GPS seconds (apexSystemTime) that this table row was saved. When GPS time is not available to the apex (apexSystemTime=0) a clock maintained inside the APEX will be used. This clock starts at GPS time zero when the apex is booted. The APEX will use real GPS time if and when GPS time becomes available to the APEX.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOutputTsUtilizCurPercent 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.6
Percent utilization of most recently taken sample.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

apexOutputTsUtilizAvgPercent 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.7
Average percent utilization over the rolling sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

apexOutputTsUtilizMinPercent 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.8
Minimum percent utilization for a sample during the rolling sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

apexOutputTsUtilizPeakPercent 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.9
Peak percent utilization for a sample during the rolling sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

apexOutputTsUtilizCurRate 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.10
Utilization of most recently taken sample in bits per second (bps).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOutputTsUtilizAvgRate 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.11
Average utilization for the rolling sampling interval in bits per second (bps).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOutputTsUtilizMinRate 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.12
Minimum utilization for a sample during this sampling interval in bits per second (bps).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOutputTsUtilizPeakRate 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.13
Peak utilization for a sample during the rolling sampling interval in bits per second (bps).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOutputTsUtilizOverflow 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.14
Indicates whether an overflow error has occurred. This field will clear if the output has no overflows. This field is also cleared when the QAM output is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), noError(1), overflow(2)  

apexOutputTsUtilizCurDropPackets 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.15
MPEG packets dropped during the most recently taken sample.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOutputTsUtilizPeakDropPackets 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.16
Peak MPEG packets dropped for a sample during the rolling sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOutputTsUtilizRollingDropPackets 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.17
Total MPEG packets dropped during the rolling sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOutputTsUtilizTotalDropPackets 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.18
Total MPEG packets dropped on the QAM Output. Can be reset using apexOutputTsUtilMonResetTotDropPacket.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexOutputTsUtilizThresholdAlarm 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.19
Current fault condition of apexOutputTsUtilizThreshold. This is the apexAlarmOutputUtilizationFault level for this output.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexOutputTsUtilizOverflowAlarm 1.3.6.1.4.1.1166.1.31.14.2.2.2.1.20
Current fault condition of apexOutputTsUtilizOverflow. This is the apexAlarmOutputOverflow level for this output.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexOutputTsStatusTable 1.3.6.1.4.1.1166.1.31.14.2.5
Table of Output Transport Status. Indexed by Output Transport Stream number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexOutputTsStatusEntry

apexOutputTsStatusEntry 1.3.6.1.4.1.1166.1.31.14.2.5.1
A row in the Output Transport Stream Status table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexOutputTsStatusEntry  

apexOutputTsStatusOutputTsNum 1.3.6.1.4.1.1166.1.31.14.2.5.1.1
Output Transport Stream Number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexOutputTsStatusProgramsPerTs 1.3.6.1.4.1.1166.1.31.14.2.5.1.2
Number of Output Programs supported on this Output Transport Stream.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsStatusServicesMapped 1.3.6.1.4.1.1166.1.31.14.2.5.1.3
Number of services currently mapped to the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsStatusAncillaryPidsMapped 1.3.6.1.4.1.1166.1.31.14.2.5.1.4
Number of ancillary PIDs currently mapped to the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsStatusInputStreamsMapped 1.3.6.1.4.1.1166.1.31.14.2.5.1.5
Number of input streams currently mapped to the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsStatusFault 1.3.6.1.4.1.1166.1.31.14.2.5.1.6
Highest current fault condition associated with this Output Transport Stream. The following Alarms are included: - apexAlarmOutputOverflow - apexAlarmOutputUtilizationFault - apexAlarmQamModuleFault - apexAlarmQamRfPortFault - apexAlarmQamChannelFault
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexOutputTsStatusServicesInError 1.3.6.1.4.1.1166.1.31.14.2.5.1.7
Number of services in error mapped to the output stream.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsStatusDepiSessionsMapped 1.3.6.1.4.1.1166.1.31.14.2.5.1.8
Number of DEPI sessions currently mapped to the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsStatusMessageGenerationNum 1.3.6.1.4.1.1166.1.31.14.2.5.1.9
Number of messages generated (DVB tables) currently in the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsStatusScgsProvisioned 1.3.6.1.4.1.1166.1.31.14.2.5.1.10
Number of SCGs provisioned currently in the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsStatusServicesMuxed 1.3.6.1.4.1.1166.1.31.14.2.5.1.11
Number of services successfully multiplexed.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexPsiDetectionEnabled 1.3.6.1.4.1.1166.1.31.15.1.1.1
The loss of input PSI detection enabled or disabled setting. When enabled, the APEX will check for missing input PSI (PATs and PMTs) based on the PSI detection timeout value. When an input PSI message is determined to be missing, the APEX will assume the input service or services are no longer being streamed and unmap the service(s). This checking only occurs after an initial PSI message has been extracted. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexPsiDetectionTimeout 1.3.6.1.4.1.1166.1.31.15.1.1.2
The loss of input PSI detection timeout value. When PSI detection is enabled, this is the number of seconds the APEX will use to determine if an input PSI message is missing. Each PSI message previously extracted will be checked to determine that it is still being received based on this setting. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..21600  

apexPsiRangeStart 1.3.6.1.4.1.1166.1.31.15.1.1.3
Minimum PSI version number. Used to limit the APEX to use a specific range of PSI numbers. Set this to 0 to allow the APEX to use the full range of PSI version numbers (requires apexPsiRangeStop to be set to 31). Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..15  

apexPsiRangeStop 1.3.6.1.4.1.1166.1.31.15.1.1.4
Maximum PSI version number. Used to limit the APEX to use a specific range of PSI numbers. Set this to 31 to allow the APEX to use the full range of PSI version numbers (requires apexPsiRangeStart to be set to 0). Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..31  

apexPatVersionIncrement 1.3.6.1.4.1.1166.1.31.15.1.1.5
Increment of PAT version upon reboot. Used to force the APEX to use a different PAT version number upon rebooting. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..15  

apexPmtVersionIncrement 1.3.6.1.4.1.1166.1.31.15.1.1.6
Increment of PMT version upon reboot. Used to force the APEX to use a different PMT version number upon rebooting. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..15  

apexEcmEmmFirstPid 1.3.6.1.4.1.1166.1.31.15.1.1.7
First ECM-EMM PID when PID Remapping is disabled on an output stream. This PID along with the apexEcmEmmNumberPids defines a range of PIDs that the APEX will use for all ECMs and EMMs. These configuration settings allow a user to select a range that other service and ancillary PIDs will not use. This allows the APEX to use PIDs for ECMs and EMMs without having PID collisions. PID collisions will cause the APEX to select another ECM or EMM PID causing momentary glitches of the output video and audio. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..8191  

apexEcmEmmNumberPids 1.3.6.1.4.1.1166.1.31.15.1.1.8
Number of ECM-EMM PIDs to use when PID Remapping is disabled on an output stream. Refer to the apexEcmEmmFirstPid parameter for a complete description. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apexProgramBasedPmtOffset 1.3.6.1.4.1.1166.1.31.15.1.1.9
Program Based PID Remapping PMT PID offset. Determines the first PMT PID to use when Program Based algorithm selected. PMT PID is calculated as: (Program Number + Offset) * 16 Program Numbers can range from 1 - 255, allowing for PMTs to start at 0x0020 or 0x0030 up to 0x1000 and 0x1010. Changes to offset will NOT require a reboot, but if there are any service mappings already in use on an output in Program Based mode, then the change will NOT take effect and the user will have to remove all mappings on outputs in Program Based mode. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1 | 2  

apexPsiStatusTable 1.3.6.1.4.1.1166.1.31.15.2.2
The following table contains a list of messages that are either being extracted from the input side or being inserted to the output side of the apex. On the input side all extracted messages that are being used by the APEX are displayed. On the output side, only PATs, PMTs, and CATs are displayed. These messages were either given to the apex when it is in external mode or created by the apex when it is in internal mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexPsiStatusEntry

apexPsiStatusEntry 1.3.6.1.4.1.1166.1.31.15.2.2.1
PSI Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexPsiStatusEntry  

apexPsiStatusTableType 1.3.6.1.4.1.1166.1.31.15.2.2.1.1
Indicates whether this message is extracted from an input or being inserted on an output.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER inputPsiTable(1), outputPsiTable(2)  

apexPsiStatusIndex 1.3.6.1.4.1.1166.1.31.15.2.2.1.2
Indicates the input index or output number for which this message applies. For input, this is the index into the apexInputTsStatTable (1..784). For output, this is the Output Transport Stream number (1..48).
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..784  

apexPsiStatusPid 1.3.6.1.4.1.1166.1.31.15.2.2.1.3
Indicates the PID that this message is contained in.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..8191  

apexPsiStatusMessageType 1.3.6.1.4.1.1166.1.31.15.2.2.1.4
Indicates the MPEG message type of this message.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

apexPsiStatusProgramNumber 1.3.6.1.4.1.1166.1.31.15.2.2.1.5
Indicates the Program Number which this message is part of. When a message is not specifically related to a program, this value is 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

apexPsiStatusSegment 1.3.6.1.4.1.1166.1.31.15.2.2.1.6
Indicates the segment number of this message. Useful for PAT messages. Otherwise this is 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..256  

apexPsiStatusPart 1.3.6.1.4.1.1166.1.31.15.2.2.1.7
Since a message can be 1024 bytes long the message may divided into parts. Each part of the message is indexed using this index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

apexPsiStatusBody 1.3.6.1.4.1.1166.1.31.15.2.2.1.8
Raw ASCII hex of the PSI message.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexPsiStatusGpsTime 1.3.6.1.4.1.1166.1.31.15.2.2.1.9
The GPS time when the PSI was added to the table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputProgramTable 1.3.6.1.4.1.1166.1.31.16.2.2
This table shows the input program to output program mapping status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexOutputProgramEntry

apexOutputProgramEntry 1.3.6.1.4.1.1166.1.31.16.2.2.1
Output Program Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexOutputProgramEntry  

apexOutputProgramIndex 1.3.6.1.4.1.1166.1.31.16.2.2.1.1
Output Program Table Index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexOutputProgramInputTsIndex 1.3.6.1.4.1.1166.1.31.16.2.2.1.2
The index into the apexInputTsStatTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputProgramInputProgNum 1.3.6.1.4.1.1166.1.31.16.2.2.1.3
Input MPEG Program Number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputProgramOutputProgNum 1.3.6.1.4.1.1166.1.31.16.2.2.1.4
Output MPEG Program Number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputProgramRoutingStatus 1.3.6.1.4.1.1166.1.31.16.2.2.1.5
Current Program Routing Status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

apexOutputProgramInputPreEncrypted 1.3.6.1.4.1.1166.1.31.16.2.2.1.6
Indicates whether the program was pre-encrypted. Pre-encryption status is determined by the presence or absence of a CA ECM descriptor within the input PMT.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), clear(1), preEncrypted(2)  

apexOutputProgramOutputTsNum 1.3.6.1.4.1.1166.1.31.16.2.2.1.7
Output Transport Stream Number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..48  

apexOutputProgramError 1.3.6.1.4.1.1166.1.31.16.2.2.1.8
Indicates if the program is in error.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexOutputProgramEncryptionMode 1.3.6.1.4.1.1166.1.31.16.2.2.1.9
Currently configured encryption mode for the program. none - indicates the program is not being encrypted for CTE or Broadcast encryption. unencrypted - Applies to Broadcast services only. Unencrypted services are treated the same as clear services (no encryption). preEncrypted - Applies to Broadcast services only. Input program pre-encryption checking is applied. Output program is not encrypted by the APEX, regardless if input encrypted or not. unencryptedWithCci - True unencrypted mode where packets are not scrambled, but ECMs are inserted and ECM CA reference is added to output PMT (PRK contains Copy Protection information).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), full(1), fwk(2), fpk(3), clear(4), unencrypted(5), preEncrypted(6), unencryptedWithCci(7)  

apexOutputProgramEncryptionStatus 1.3.6.1.4.1.1166.1.31.16.2.2.1.10
Current Program Encryption Status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

apexOutputProgramEcmServiceId 1.3.6.1.4.1.1166.1.31.16.2.2.1.11
The ECM service ID used when this program is encrypted. This is the service ID used in all ECM messages for this program.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputProgramCciLevel 1.3.6.1.4.1.1166.1.31.16.2.2.1.12
Copy protection CCI Level. This is only applicable when the program is being encrypted.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notDefined(1), copyFreely(2), copyOnce(3), copyNever(4), noMoreCopies(5)  

apexOutputProgramApsLevel 1.3.6.1.4.1.1166.1.31.16.2.2.1.13
Copy protection Analog Protection Services Level. This is only applicable when the program is being encrypted.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), notDefined(1), off(2), splitBurstOff(3), splitBurst2Line(4), splitBurst4Line(5)  

apexOutputProgramCitSetting 1.3.6.1.4.1.1166.1.31.16.2.2.1.14
Copy protection Constraint Image Trigger setting. This is only applicable when the program is being encrypted.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), disabled(1), enabled(2)  

apexOutputProgramNumberTiers 1.3.6.1.4.1.1166.1.31.16.2.2.1.15
The number of program tiers. This is only applicable when the program is being encrypted.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputProgramTierData 1.3.6.1.4.1.1166.1.31.16.2.2.1.16
Current Program Tier Data. Tier information is in hexadecimal format. Up to 7 tiers of information are provided for each program. Tier information for each program consists of 8 bytes of information. First 4 bytes are the program tier value in hexadecimal. Next 4 bytes are the tier type in hexadecimal format. This is only applicable when the program is being encrypted.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexOutputProgramSourceId 1.3.6.1.4.1.1166.1.31.16.2.2.1.17
Broadcast Encryption Source ID. Only applies to programs when the input type is Gbe and the output encryption mode is Broadcast Encryption. (apexOutputTsConfEncryptionType set to 'broadcastEncryption')
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

apexOutputProgramProviderId 1.3.6.1.4.1.1166.1.31.16.2.2.1.18
Broadcast Encryption Provider ID. Only applies to programs when the input type is Gbe and the output encryption mode is Broadcast Encryption. (apexOutputTsConfEncryptionType set to 'broadcastEncryption')
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

apexOutputProgramProgramType 1.3.6.1.4.1.1166.1.31.16.2.2.1.19
Indicates how programs are to be built by the encryptor. 1 - programsDerived (default) - programs are derived where the encryptor builds the programs internally for the specified service. The program related ECM messages and program name/info messages are derived from the service RMD data and internal schedules. This program type is typically used for subscription services. 2 - programInfoProvided - the encryptor should build the programs based on the program information provided by the controller via the element of the ServiceProgramReply payload. The service RMD data is still used to generate the program related ECM messages. 3 - programEcmProvided - the encryptor should use pre-built ECM program messages as provided by the controller via the element of the ServiceProgramReply payload. For this program type, the controller provides the schedules; however, the encryptor must default much of the program info message since not detailed program information is provided. DTA content protection encryption makes use of the 'programEcmProvided' program type since the ECM messages cannot be derived by the encryptor. 4 - programInfoAndEcmProvided - the encryptor should build the programs based on both the program information and pre-built ECM messages provided by the controller via the and elements of the ServiceProgramReply payload.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER programsDerived(1), programInfoProvided(2), programEcmProvided(3), programInfoAndEcmProvided(4)  

apexOutputProgramDtaEncryptionMode 1.3.6.1.4.1.1166.1.31.16.2.2.1.20
This parameter identifies whether a service in Full Encryption is in Modified Privacy Mode (DTA) and whether the DTA service has CCM messages. This parameter is applicable only when apexOutputProgramEncryptionMode is 'full'. In other encryption modes this value is ignored. notApplicable - Non DTA Service and/or No DTA CA descriptor found dtaWithCcm - DTA, Full Encryption, Modified Privacy Mode, CCM present dtaWithoutCcm - DTA, Full Encryption, Modified Privacy Mode, CCM absent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), dtaWithCcm(1), dtaWithoutCcm(2)  

apexAcpStatusTable 1.3.6.1.4.1.1166.1.31.17.2.2
This table shows the status of the Control Word Generating ACPs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexAcpStatusEntry

apexAcpStatusEntry 1.3.6.1.4.1.1166.1.31.17.2.2.1
Output Program Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexAcpStatusEntry  

apexAcpStatusIndex 1.3.6.1.4.1.1166.1.31.17.2.2.1.1
Acp Status Index. Index for one of six control word generating ACPs.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..6  

apexAcpUnitAddress 1.3.6.1.4.1.1166.1.31.17.2.2.1.2
The unit address of the ACP in ASCII Hex. The Unit address is a 5 byte value.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..11)  

apexAcpHealthByte 1.3.6.1.4.1.1166.1.31.17.2.2.1.3
The health byte of the ACP. Indicates whether the ACP has intact fuses. The health should read 255 (hex 0xFF) for all APEX ACPs. Otherwise, the ACP will not properly function.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexAcpEvenCsn 1.3.6.1.4.1.1166.1.31.17.2.2.1.4
The Even Category Sequence Number of the ACP. Should match the even CSN assigned by DAC, if not may indicate a communications problem.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexAcpOddCsn 1.3.6.1.4.1.1166.1.31.17.2.2.1.5
The Odd Category Sequence Number of the ACP. Should match the odd CSN assigned by DAC, if not may indicate a communications problem.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexAcpUnitAttribute 1.3.6.1.4.1.1166.1.31.17.2.2.1.6
Unit attribute byte is made available to verify that the MC2.1 was properly unit created during factory production.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexUdpMapPreEncryptCheck 1.3.6.1.4.1.1166.1.31.18.1.1.1
UDP Mapping pre-encryption checking. Indicates if the APEX is to check if input services are pre-encrypted or clear. Pre-encrypted is determined by examining the input PMT for a CA ECM descriptor (any CA ECM descriptor). If pre-encrypted, setting this flag will cause the APEX to pass through ECM PID for the service. For input services that have a GI CA ECM descriptor, the APEX will also pass through the PIT message (extract and re-insert the PIT). The output PMT for pre-encrypted services will contain a CA ECM descriptor (referencing the ECM PID). When PID Remapping is enabled, pre-encryption for a service is only valid when the input ECM PID is on a different PID than the associated PMT PID. If this flag is set to pre-encryption and the input service is not pre-encrypted, then the setting of this flag has no affect on the output service. Once written, the change to this parameter will take immediate effect and all mappings will be removed. Mappings will not be re-added until apexUdpMapApplyChange is set to 'apply' for all transport streams. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexUdpMapModeBits 1.3.6.1.4.1.1166.1.31.18.1.1.2
Value that will be placed in the two MSBs of each the calculated UDP port number (bits 14 and 15). Once written, the change to this parameter will take immediate effect and all mappings will be removed. Mappings will not be re-added until apexUdpMapApplyChange is set to 'apply' for all transport streams. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..3  

apexUdpMapTsOffset 1.3.6.1.4.1.1166.1.31.18.1.1.3
Used as part of the Standardized UDP Port calculation. Transport Stream index can be relative 0 or relative 1. Once written, the change to this parameter will take immediate effect and all mappings will be removed. Mappings will not be re-added until apexUdpMapApplyChange is set to 'apply' for all transport streams. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1  

apexUdpMapFollowDtcp 1.3.6.1.4.1.1166.1.31.18.1.1.4
Determines how the copy protection settings (CCI, APS, and CIT) within the PRK will be set. All outputs in UDP Port Mapping mode will use this setting for following input DTCP. Disabled - Use CTE configured settings if output in CTE encryption mode Enabled - Follow input DTCP Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexUdpMapApplyTable 1.3.6.1.4.1.1166.1.31.18.1.2
Table of Apply Change for the data for UDP Map Table. A row in this table corresponds to the same row index in the UDP Map table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexUdpMapApplyEntry

apexUdpMapApplyEntry 1.3.6.1.4.1.1166.1.31.18.1.2.1
UDP Map Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexUdpMapApplyEntry  

apexUdpMapApplyOutputTsNum 1.3.6.1.4.1.1166.1.31.18.1.2.1.1
The index of the Udp Map Apply Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexUdpMapApplyChange 1.3.6.1.4.1.1166.1.31.18.1.2.1.2
The Apply for the row of data in the Udp Map Table. A row in this table corresponds to the same row index in the Udp Map table. This parameter MUST be set to 'apply' in order for any of the data in the Udp Map Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the Udp Map Table row has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexUdpMapTable 1.3.6.1.4.1.1166.1.31.18.1.3
Table of data for Udp Mapping. There are 48 rows in this table. Each row corresponds to one QAM channel. Once written, the change to this table will only take immediate effect after apexUdpMapApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexUdpMapApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexUdpMapEntry

apexUdpMapEntry 1.3.6.1.4.1.1166.1.31.18.1.3.1
Udp Mapping Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexUdpMapEntry  

apexUdpMapOutputTsNum 1.3.6.1.4.1.1166.1.31.18.1.3.1.1
Index of Udp Mapping Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexUdpMapInputInterface 1.3.6.1.4.1.1166.1.31.18.1.3.1.2
Input GBE port. Range: '1 - 4' = GBE port number
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..4  

apexUdpMapStartProgNum 1.3.6.1.4.1.1166.1.31.18.1.3.1.3
Indicates the first program number in a sequential range of programs that are to be routed to the same output transport stream.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

apexUdpMapNumberProgs 1.3.6.1.4.1.1166.1.31.18.1.3.1.4
Indicates the number of programs that are to be mapped to the output transport stream. One UDP port is opened for each program mapped to the output transport stream.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..200  

apexUdpMapMulticastTable 1.3.6.1.4.1.1166.1.31.18.1.4
Table of data for UDP Map Multicast. Each entry in this table identifies a Gigabit Ethernet input stream that is used for multicast UDP Port Mapping. Once written, the change to this table will only take immediate effect after apexUdpMapMulticastApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexUdpMapMulticastApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(bcmr.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexUdpMapMulticastEntry

apexUdpMapMulticastEntry 1.3.6.1.4.1.1166.1.31.18.1.4.1
UDP Map Multicast Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexUdpMapMulticastEntry  

apexUdpMapMulticastIndex 1.3.6.1.4.1.1166.1.31.18.1.4.1.1
Index of UDP Map Multicast Stream Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..256  

apexUdpMapMulticastEnable 1.3.6.1.4.1.1166.1.31.18.1.4.1.2
Indicates whether this UDP Map Multicast entry is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexUdpMapMulticastInterface 1.3.6.1.4.1.1166.1.31.18.1.4.1.3
Number of the input interface (Port number). Range: '0' = Not Applicable GBE = 1-4
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4  

apexUdpMapMulticastUdp 1.3.6.1.4.1.1166.1.31.18.1.4.1.4
GBE Input UDP Port. Range: 0-65535
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexUdpMapMulticastMcastIp 1.3.6.1.4.1.1166.1.31.18.1.4.1.5
The Multicast receive IP address. An IP address of 0.0.0.0 indicates singlecast only. Multicast IP addresses 224.0.0.0 to 224.0.0.255 are reserved.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexUdpMapMulticastSourceIp 1.3.6.1.4.1.1166.1.31.18.1.4.1.6
This is the IP address of the source device. This field is only used when a multicast IP address is also specified.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexUdpMapMulticastApplyTable 1.3.6.1.4.1.1166.1.31.18.1.5
Table of Apply Change for the UDP Map Multicast Table. A row in this table corresponds to the same row index in the UDP Map Multicast Table (apexUdpMapMulticastTable).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexUdpMapMulticastApplyEntry

apexUdpMapMulticastApplyEntry 1.3.6.1.4.1.1166.1.31.18.1.5.1
UDP Map Multicast Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexUdpMapMulticastApplyEntry  

apexUdpMapMulticastApplyIndex 1.3.6.1.4.1.1166.1.31.18.1.5.1.1
The index of the UDP Map Multicast Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..256  

apexUdpMapMulticastApplyChange 1.3.6.1.4.1.1166.1.31.18.1.5.1.2
The Apply for the row of data in the UDP Map Multicast Table. A row in this table corresponds to the same row index in the UDP Map Multicast Table. This parameter MUST be set to 'apply' in order for any of the data in the UDP Map Multicast Table row to take effect in the APEX. This parameter MUST be set LAST after all other data in the UDP Map Multicast Table row has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexUdpMapMulticastInvalidApplyText 1.3.6.1.4.1.1166.1.31.18.2.1.1
When apexUdpMapMulticastApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexUdpMapStatusTable 1.3.6.1.4.1.1166.1.31.18.2.2
Table of status data for Udp Mapping. There are 48 rows in this table. Each row corresponds to one QAM channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexUdpMapStatusEntry

apexUdpMapStatusEntry 1.3.6.1.4.1.1166.1.31.18.2.2.1
Udp Mapping Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexUdpMapStatusEntry  

apexUdpMapStatusOutputTsNum 1.3.6.1.4.1.1166.1.31.18.2.2.1.1
Index of Udp Mapping Status Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexUdpMapInvalidApplyText 1.3.6.1.4.1.1166.1.31.18.2.2.1.2
When apexUdpMapApplyChange is set to applyNotInProgressInvalidData, this entry may contain a text description of what was wrong with the data.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexRdsIpAddr 1.3.6.1.4.1.1166.1.31.19.1.1.1
Rights Data Server IP address. Class A, B, or C IP address of the RDS. Changing this parameter will cause the APEX to perform an EMM rollover sequence. This parameter is not changed by apexRdsSetDefault. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexRdsTcpPort 1.3.6.1.4.1.1166.1.31.19.1.1.2
Rights Data Server TCP port. Changing this parameter will cause the APEX to perform an EMM rollover sequence. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexRdsProgramEpochDuration 1.3.6.1.4.1.1166.1.31.19.1.1.3
The Program Epoch Duration in minutes. Changes are not applied until the end of the current epoch. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..1440  

apexRdsCetPollInterval 1.3.6.1.4.1.1166.1.31.19.1.1.4
Interval that the APEX will use to poll for CSN/State information. After receiving the CSN/State information, the APEX will determine if it needs to retrieve new EMMs. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 15..1440  

apexRdsCetRefresh 1.3.6.1.4.1.1166.1.31.19.1.1.5
Setting to 'refresh' forces the APEX to retrieve new EMMs (APEX performs an EMM rollover sequence). Once written, the change to this parameter will take effect immediately. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER refreshNotInProgress(1), refresh(2)  

apexRdsRmdPollInterval 1.3.6.1.4.1.1166.1.31.19.1.1.6
Interval that the APEX will use to poll for RMD information. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 15..1440  

apexRdsRmdRefresh 1.3.6.1.4.1.1166.1.31.19.1.1.7
Setting to 'refresh' forces the APEX to retrieve new RMD data from RDS server. Once written, the change to this parameter will take effect immediately. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER refreshNotInProgress(1), refresh(2)  

apexRdsPollRandomization 1.3.6.1.4.1.1166.1.31.19.1.1.8
RDS Polling Randomization Time. Maximum time in minutes to delay polling at startup in order to avoid having many APEXs polling the RDS simultaneously. The actual delay time will be randomly calculated by the APEX and will be no greater than this value. A value of zero means no delay and the APEX will poll immediately at startup. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10  

apexRdsSetDefault 1.3.6.1.4.1.1166.1.31.19.1.1.9
This parameter sets apexRdsCetPollInterval, apexRdsPollRandomization, apexRdsTcpPort, apexRdsRmdPollInterval, apexRdsProgramEpochDuration and apexRdsInitialEcmRetryInterval to default values. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'.. @Config(config=no, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSettingToDefault(1), setToDefault(2)  

apexRdsErrorCountReset 1.3.6.1.4.1.1166.1.31.19.1.1.10
Resets RDS Communication error counts. Once written, the change to this parameter will take effect immediately. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ResetStatisticsTYPE  

apexRdsConfigApplyChange 1.3.6.1.4.1.1166.1.31.19.1.1.11
The Apply for RDS configuration items. This parameter MUST be set to 'apply' in order for any of the following to take effect: apexRdsIpAddr apexRdsTcpPort apexRdsPollRandomization apexRdsCetPollInterval apexRdsRmdPollInterval apexRdsProgramEpochDuration apexRdsConfigRds2Enable apexRdsConfigServerUrl This parameter MUST be set LAST after all associated parameters has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexRdsConfigRds2Enable 1.3.6.1.4.1.1166.1.31.19.1.1.12
Indicates whether RDS-2 Interface is enabled or disabled. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexRdsConfigServerUrl 1.3.6.1.4.1.1166.1.31.19.1.1.13
Rights Data Server Uniform Resource Locator (RDS-2 Server URL). This is introduced to support RDS 2 Interface since APEX 2.5 release. The syntax of this parameter shall be: [http://][:]/ Note: 1. The 'http://' protocol part is default and optional, 2. 'RDS-2 Server IP' is Class A, B, or C IP address, 3. 'TCP Port' is optional, if not present, default to 80, 4. 'Server Root Directory Path' is not optional e.g. http://192.168.30.107:1020/rds/controller 192.168.30.107:1020/rds/controller 192.168.30.107/rds/controller (default port is 80) The apex host will validate this parameter upon applying change, and set the following three status parameter accordingly: - apexRdsStatusServerIp - apexRdsStatusServerPort - apexRdsStatusServerRootDirPath - apexRdsStatusValidation This parameter is not changed by apexRdsSetDefault. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..254)  

apexRdsInitialEcmRetryInterval 1.3.6.1.4.1.1166.1.31.19.1.1.14
This parameter is used to configure RDS2 server ECM retry time. This value defines when the next retry will be performed by the host. Units are seconds. Once written, the change to this parameter will only take immediate effect after apexRdsConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexRdsConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..30  

apexRdsConnectionStatus 1.3.6.1.4.1.1166.1.31.19.2.1.1
Rights Data Server connection status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notConnectedInHoldoff(1), notConnectedNoRdsIpAddress(2), csnAquisitionSuccessful(3), emmAquisitionSuccessful(4), serviceListAquisitionSuccessful(5), rmdAquisitionSuccessful(6), csnAquisitionFailed(7), emmAquisitionFailed(8), serviceListAquisitionFailed(9), rmdAquisitionFailed(10)  

apexRdsCurrentCsn 1.3.6.1.4.1.1166.1.31.19.2.1.2
This is the current CSN that the APEX is using for encrypting all programs.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

apexRdsCetNextPollTime 1.3.6.1.4.1.1166.1.31.19.2.1.3
Time in seconds until the next CET polling period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsRmdNextPollTime 1.3.6.1.4.1.1166.1.31.19.2.1.4
Time in seconds until the next RMD polling period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsEmmStatusTableSize 1.3.6.1.4.1.1166.1.31.19.2.1.5
EMM Status Table Size. This is the maximum number of rows in the EMM Status Table and is the limit on apexRdsEmmStatusIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsProgramMessagesReceived 1.3.6.1.4.1.1166.1.31.19.2.1.6
Number of successful ServiceEncrypt messages received in the last 15 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexRdsProgramMessagesFailed 1.3.6.1.4.1.1166.1.31.19.2.1.7
Number of failed ServiceEncrypt messages received in the last 15 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexRdsCommErrorCount 1.3.6.1.4.1.1166.1.31.19.2.1.8
Count of total server communication errors. This parameter is set to 0 when the APEX boots up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexRdsCommStatus 1.3.6.1.4.1.1166.1.31.19.2.1.9
Status of communication with RDS.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ok(1), error(2)  

apexRdsFlashWriteCount 1.3.6.1.4.1.1166.1.31.19.2.1.10
Running count of the number of flash memory erasures/writes.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexRdsMcast16 1.3.6.1.4.1.1166.1.31.19.2.1.11
Multicast-16 bit address used for build PRK messages. The multicast-16 bit address is from the EMMs received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexRdsStatusServerIp 1.3.6.1.4.1.1166.1.31.19.2.1.12
Effective Rights Data Server IP address. Derived from RDS Server URL. This is set to 0.0.0.0 when validation on RDS Server URL fails. See apexRdsConfigServerUrl.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexRdsStatusServerPort 1.3.6.1.4.1.1166.1.31.19.2.1.13
Effective Rights Data Server TCP port. Derived from RDS Server URL. This is set to 0 when validation on RDS Server URL fails. See apexRdsConfigServerUrl.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

apexRdsStatusServerRootDirPath 1.3.6.1.4.1.1166.1.31.19.2.1.14
Effective Rights Data Server Root Directory Path. Derived from RDS Server URL. This is set to Null String when validation on RDS Server URL fails. See apexRdsConfigServerUrl.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..254)  

apexRdsStatusValidation 1.3.6.1.4.1.1166.1.31.19.2.1.15
Indicates whether the current RDS Server URL parameter is valid. urlValid (1) - RDS-2 URL is valid, missingIpOrPath (2) - RDS-2 IP or Root Path is missing, emptyRootPath (3) - RDS-2 Root Path cannot be empty, invalidTcpPort (4) - RDS-2 TCP Port ranges from 1~65535, default to 80, invalidIpClass (5) - RDS-2 IP shall be class A/B/C. See apexRdsConfigServerUrl.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), urlValid(1), missingIpOrPath(2), emptyRootPath(3), invalidTcpPort(4), invalidIpClass(5)  

apexRdsEmmStatusTable 1.3.6.1.4.1.1166.1.31.19.2.2
Table of the most recent RDS responses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRdsEmmStatusEntry

apexRdsEmmStatusEntry 1.3.6.1.4.1.1166.1.31.19.2.2.1
RDS EMM Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRdsEmmStatusEntry  

apexRdsEmmStatusIndex 1.3.6.1.4.1.1166.1.31.19.2.2.1.1
Index of EMM Status Table. Size of table can be found in apexRdsEmmStatusTableSize.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

apexRdsEmmStatusCsn 1.3.6.1.4.1.1166.1.31.19.2.2.1.2
Category Sequence Number (CSN).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

apexRdsEmmStatusState 1.3.6.1.4.1.1166.1.31.19.2.2.1.3
Category Epoch Transition (CET) State.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER transitionComplete(1), transitionStart(2), startOfNewEpoch(3)  

apexRdsEmmStatusGpsTime 1.3.6.1.4.1.1166.1.31.19.2.2.1.4
This is the time in GPS seconds that this row was written.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsEmmStatusServerError 1.3.6.1.4.1.1166.1.31.19.2.2.1.5
This is the error code reported to the APEX by the RDS. Zero indicates no error.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexRdsEmmStatusUnitAddress 1.3.6.1.4.1.1166.1.31.19.2.2.1.6
This is the ACP address of the ACP associated with the error reported in apexRdsEmmStatusServerError. If no address is contained in this entry, the error applies to all ACPs or to the entire APEX. The address is made up of decimal digits formatted as ###-#####-#####-###.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(20)  

apexRdsSourceLookupTable 1.3.6.1.4.1.1166.1.31.19.2.3
This table provides a list of Source IDs and Provider IDs along with an associated string. This table of information is provided by the RDS to make it easier for a user to figure out the Source ID and Provider ID for a particular service.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRdsSourceLookupEntry

apexRdsSourceLookupEntry 1.3.6.1.4.1.1166.1.31.19.2.3.1
Source Lookup Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRdsSourceLookupEntry  

apexRdsSourceLookupIndex 1.3.6.1.4.1.1166.1.31.19.2.3.1.1
Source Lookup Table Index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

apexRdsSourceLookupDescription 1.3.6.1.4.1.1166.1.31.19.2.3.1.2
Text Description of the service provided by the Rights Data Server.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexRdsSourceLookupSourceId 1.3.6.1.4.1.1166.1.31.19.2.3.1.3
Source Id of the service.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsSourceLookupProviderId 1.3.6.1.4.1.1166.1.31.19.2.3.1.4
Provider Id of the service.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsEventTable 1.3.6.1.4.1.1166.1.31.19.2.4
Table of Rds2 Events. The first index (apexRdsEventProgramIndex) matches to the same row index in the apexManualRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRdsEventEntry

apexRdsEventEntry 1.3.6.1.4.1.1166.1.31.19.2.4.1
Rds2 Events Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRdsEventEntry  

apexRdsEventProgramIndex 1.3.6.1.4.1.1166.1.31.19.2.4.1.1
apexRdsEventProgramIndex is the last 10 bits of apexOutputProgramEcmServiceId from apexOutputProgramTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexRdsEventEventIndex 1.3.6.1.4.1.1166.1.31.19.2.4.1.2
Rds Event Index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexRdsEventEpochNumber 1.3.6.1.4.1.1166.1.31.19.2.4.1.3
Uniquely identifies a program epoch for the specified service.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

apexRdsEventEpochStart 1.3.6.1.4.1.1166.1.31.19.2.4.1.4
Start time in GPS seconds of the returned program epoch for the specified service.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsEventEpochEnd 1.3.6.1.4.1.1166.1.31.19.2.4.1.5
End time in GPS seconds of the returned program epoch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsEventInterstitialDuration 1.3.6.1.4.1.1166.1.31.19.2.4.1.6
The interstitial duration provides the time duration in seconds between the start of the program epoch and the start of the actual program or event.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

apexRdsEventPreviewDuration 1.3.6.1.4.1.1166.1.31.19.2.4.1.7
The preview window provides the time duration in seconds between the start of the program epoch and the start of the pay portion of the program.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

apexRdsEventPurchaseDuration 1.3.6.1.4.1.1166.1.31.19.2.4.1.8
The purchase window provides the time duration in seconds between the start of the program epoch that IPPV purchases are allowed.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

apexRdsEventNumberTiers 1.3.6.1.4.1.1166.1.31.19.2.4.1.9
A program can be associated with at most 7 tiers.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsEventTierData 1.3.6.1.4.1.1166.1.31.19.2.4.1.10
Program Tier Data in Hexadecimal format (28 bytes). Up to 7 tiers of information are provided for each program. Tier information for each program consists of 4 bytes. First 3 bytes are the Tier Value, next 1 bytes are the Tier Type.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexRdsEventProgramCost 1.3.6.1.4.1.1166.1.31.19.2.4.1.11
Represents the cost, in program units, of the program epoch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsEventRatingRegion 1.3.6.1.4.1.1166.1.31.19.2.4.1.12
Identifies the Program Rating Region. The US region attribute is 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRdsEventRatingData 1.3.6.1.4.1.1166.1.31.19.2.4.1.13
Program Rating Data in Hexadecimal format (3 bytes). Contains 6 rating dimensions where each rating dimension is a 4-bit integer that represents a different rating control for the region. A US region defines 4 rating dimensions: MPAA rating, violence content rating, language content rating and sexual content rating.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexRdsEventRatingText 1.3.6.1.4.1.1166.1.31.19.2.4.1.14
Program Rating optionally contains a Rating Text.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexRdsEventControlByte 1.3.6.1.4.1.1166.1.31.19.2.4.1.15
The program control byte used in the PRKM (1 Hexadecimal byte).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexRdsEventPrkmWkemAvailable 1.3.6.1.4.1.1166.1.31.19.2.4.1.16
The flag indicates that PRKM, WKEM (odd and even) is available for the associated epoch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER available(1), notAvailable(2)  

apexRdsEventCcmAvailable 1.3.6.1.4.1.1166.1.31.19.2.4.1.17
The flag indicates that CCM (odd and even) is available for the associated epoch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER available(1), notAvailable(2)  

apexEncryptionConfAlgorithm 1.3.6.1.4.1.1166.1.31.20.1.1.1
Configured encryption algorithm. This value determines which MUX FPGA image will be loaded. dvb-csa-simulcrypt must be selected to allow for configuration of Simulcrypt. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=yes) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER des-dcii(1), des-scte-52(2), dvb-csa(3), dvb-csa-simulcrypt(4)  

apexSimulcryptExternalEisSetting 1.3.6.1.4.1.1166.1.31.20.1.1.2
Default simulcrypt External EIS encryption setting. This determines if services are sent out in the clear or are encrypted when Simulcrypt mode is set to External EIS and the services have not yet been provisioned. This allows a user to have services scrambled but unviewable prior to services being provisioned (to prevent services from being viewable). This parameter is only applicable for output streams that are in Simulcrypt External EIS mode. When this setting is changed, it only affects new service mappings. Services that are already mapped will not be modified. Once written, a save must be performed via the apexSaveConfig parameter and the APEX must be rebooted for the change to take effect. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clear(0), encrypt(1)  

apexSimulcryptEmEnable 1.3.6.1.4.1.1166.1.31.20.1.1.3
Simulcrypt EM Enable. If set to 'enabled' the EM will display the Simulcrypt specific screens. User will be allowed to view Simulcrypt status and perform configuration changes via the EM. This parameter only enables and disables the ability to use the EM Simulcrypt screens. It does not enable or disable Simulcrypt as there is a specific Simulcrypt mode per output stream. Once written, the change to this parameter will only take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexCteEncryptionMode 1.3.6.1.4.1.1166.1.31.20.1.2.1
This parameter is used to set the Encryption Mode. It applies to all services on all QAMs in CTE mode. - 'full' - The APEX will use Full encryption. The APEX will only be able to encrypt programs in Full encryption mode if the APEX is able to communicate with an RDS. - 'fwk' - The APEX will use Fixed Working Key (FWK) encryption. - 'fpk' - The APEX will use Fixed Program Key (FPK) encryption. The APEX will not attempt to get EMMs. - 'clear' - The APEX performs no encryption of output programs. If the APEX is unable to encrypt programs in the configured mode, then those programs will not be mapped. Once written, the change to this parameter will only take immediate effect after apexCteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexCteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER full(1), fwk(2), fpk(3), clear(4)  

apexCteCciLevel 1.3.6.1.4.1.1166.1.31.20.1.2.2
Copy Control Information (CCI) Level setting for PRK messages. - notDefined - CCI is not defined, settop box applications can configure CCI - copyFreely - program can be copied - copyOnce - program can be copied once - copyNever - program can never be copied - noMoreCopies - Once written, the change to this parameter will only take immediate effect after apexCteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexCteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notDefined(1), copyFreely(2), copyOnce(3), copyNever(4), noMoreCopies(5)  

apexCteApsLevel 1.3.6.1.4.1.1166.1.31.20.1.2.3
Analog Protection System (APS) Level setting for PRK messages. Defines what copy protection encoding will be applied to the analog composite output by the settop box. - notDefined - analog protection is not defined, settop box applications can configure APS - off - no analog protection - splitBurstOff - AGC on, split burst off - splitBurst2Line - AGC on, 2 line split burst on - splitBurst4Line - AGC on, 4 line split burst on The APEX will set Tier Type based on apexCteApsLevel. The APEX will set tier type to subscription with right to tape when apexCteApsLevel is 'off' or 'notDefined'. The APEX will set tier type to subscription without right to tape when apexCteApsLevel is 'splitBurstOff', 'splitBurst2Line', or 'splitBurst4Line'. Once written, the change to this parameter will only take immediate effect after apexCteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexCteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notDefined(1), off(2), splitBurstOff(3), splitBurst2Line(4), splitBurst4Line(5)  

apexCteCitEnable 1.3.6.1.4.1.1166.1.31.20.1.2.4
Constrained Image Trigger (CIT) setting. If set to 'enabled' the settop box is notified not to allow a high quality digital output unless the receiving device also adheres to CIT processing. If the apexCteApsLevel is set to 'notDefined', the setting of the CIT value has no affect (CIT and APS are only used when APS is set to a defined value). Once written, the change to this parameter will only take immediate effect after apexCteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexCteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexCteCommonTier 1.3.6.1.4.1.1166.1.31.20.1.2.5
EncryptionCommon Tier. Identifies the tier number for which access is granted. Range is 0 to 16777215. 65535 is reserved and cannot be used. The APEX will set Tier Type based on apexCteApsLevel setting. Refer to the apexCteApsLevel description for more details. Once written, the change to this parameter will only take immediate effect after apexCteApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexCteApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..16777215  

apexCteApplyChange 1.3.6.1.4.1.1166.1.31.20.1.2.6
The Apply for CTE configuration items. This parameter MUST be set to 'apply' in order for any of the following to take effect: apexCteEncryptionMode apexCteCciLevel apexCteApsLevel apexCteCitEnable apexCteCommonTier This parameter MUST be set LAST after all associated parameters has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexEncryptionStatAlgorithm 1.3.6.1.4.1.1166.1.31.20.2.1.1
Current encryption algorithm. This value determines which MUX FPGA image will be loaded.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER des-dcii(1), des-scte-52(2), dvb-csa(3), dvb-csa-simulcrypt(4)  

apexEncryptionCwgPerSecond 1.3.6.1.4.1.1166.1.31.20.2.1.2.1
Average control words per second generated integrated over the last minute.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionMux1CollisionCount 1.3.6.1.4.1.1166.1.31.20.2.1.2.2
Triton collision counter for MUX FPGA #1.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionMux2CollisionCount 1.3.6.1.4.1.1166.1.31.20.2.1.2.3
Triton collision counter for MUX FPGA #2.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionMux1RolloverCount 1.3.6.1.4.1.1166.1.31.20.2.1.2.4
Counts rollovers of triton message circular buffer for MUX FPGA #1.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionMux2RolloverCount 1.3.6.1.4.1.1166.1.31.20.2.1.2.5
Counts rollovers of triton message circular buffer for MUX FPGA #2.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionEmmRequestsSent 1.3.6.1.4.1.1166.1.31.20.2.1.2.6
Counts number of triton EMM reports sent to 6 MC2.1 devices.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionEmmGoodRepliesRecvd 1.3.6.1.4.1.1166.1.31.20.2.1.2.7
Counts number of triton EMM replies marked good received from mc2.1 devices.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionEmmBadRepliesRecvd 1.3.6.1.4.1.1166.1.31.20.2.1.2.8
Counts number of triton EMM replies marked bad received from mc2.1 devices.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionEmmGoodDeliveryTimeMs 1.3.6.1.4.1.1166.1.31.20.2.1.2.9
Amount of time expressed in milliseconds taken to deliver entire set of EMMs for most recent successful attempt. Note it takes MC2.1 a significant amount of time to process an EMM. They are delivered in batches of 6 (1 per MC2.1) the firmware then waits for all 6 EMM replies before continuing with the next batch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionEmmMaxDeliveryTimeMs 1.3.6.1.4.1.1166.1.31.20.2.1.2.10
Maximum amount of time expressed in milliseconds taken to deliver an entire set of EMMs since the Apex unit was last rebooted.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionEmmMinDeliveryTimeMs 1.3.6.1.4.1.1166.1.31.20.2.1.2.11
Minimum amount of time expressed in milliseconds taken to deliver an entire set of EMMs since the Apex unit was last rebooted.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexEncryptionMcDiagTable 1.3.6.1.4.1.1166.1.31.20.2.1.2.12
Diagnostic table that breaks out individual mc21 performance parameters. Indexed 1-6 for the 6 MC2.1 devices in an APEX ACP Module.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexEncryptionMcDiagEntry

apexEncryptionMcDiagEntry 1.3.6.1.4.1.1166.1.31.20.2.1.2.12.1
A row in the mc2.1 diagnostic table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexEncryptionMcDiagEntry  

apexEncryptionMcDiagDeviceIndex 1.3.6.1.4.1.1166.1.31.20.2.1.2.12.1.1
Index represents 1 of 6 MC2.1 devices installed on ACP Module.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..6  

apexEncryptionCwCountsPerSecond 1.3.6.1.4.1.1166.1.31.20.2.1.2.12.1.2
Number of CW successfully generated on this MC2.1 per second, integrated over the last minute.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexEasApplyChange 1.3.6.1.4.1.1166.1.31.21.1.1.1
This object is obsolete. The Apply for any entries in the apexEasConfigGeneral group. This parameter MUST be set to 'apply' in order for any of the data in the apexEasConfigGeneral group to take effect. This parameter MUST be set LAST after all other data in the group has been configured. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: obsolete Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexEasPhysInType 1.3.6.1.4.1.1166.1.31.21.1.1.2
This object is obsolete. Input Type of input from which to extract EAS messages. When set to 0, no EAS is received (disables EAS extraction). Once written, the change to this parameter will only take immediate effect after apexEasApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexEasApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(0), gbe(1), fastEnet(2)  

apexEasPhysInPort 1.3.6.1.4.1.1166.1.31.21.1.1.3
This object is obsolete. Number of the input, of type configured by apexEasPhysInType, from which to extract EAS messages. Once written, the change to this parameter will only take immediate effect after apexEasApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(min=0) @Config(config=yes, reboot=no) @Commit(param=apexEasApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

apexEasRcvUdpPort 1.3.6.1.4.1.1166.1.31.21.1.1.4
This object is obsolete. This parameter indicates the UDP port on which to receive EAS messages. Range is 1024 to 65535 when apexEasPhysInType is 'fastEnet'. Range is 0 to 65535 when apexEasPhysInType is 'gbe'. Once written, the change to this parameter will only take immediate effect after apexEasApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexEasApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexEasMulticastIpAddress 1.3.6.1.4.1.1166.1.31.21.1.1.5
This object is obsolete. This parameter indicates the Multicast IP Receive address on which to receive EAS messages. If 0.0.0.0, then EAS messages will be received via singlecast only. Once written, the change to this parameter will only take immediate effect after apexEasApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexEasApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

apexEasSourceIpAddress 1.3.6.1.4.1.1166.1.31.21.1.1.6
This object is obsolete. This parameter indicates the Source IP Receive address on which to receive EAS messages. This is only for IGMP v3 networks. If 0.0.0.0, then source IP is not used. Once written, the change to this parameter will only take immediate effect after apexEasApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexEasApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

apexEasOutputTable 1.3.6.1.4.1.1166.1.31.21.1.2
Table of parameters for configuring EAS Output. Table is indexed by Output Transport Stream Number. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexEasOutputEntry

apexEasOutputEntry 1.3.6.1.4.1.1166.1.31.21.1.2.1
A row in the EAS output table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexEasOutputEntry  

apexEasOutputStreamNum 1.3.6.1.4.1.1166.1.31.21.1.2.1.1
The output transport stream number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexEasOutputEnable 1.3.6.1.4.1.1166.1.31.21.1.2.1.2
The enable setting for EAS output on this Output Transport Stream. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEasServerApplyTable 1.3.6.1.4.1.1166.1.31.21.1.3
Apply table for the apexEasServerTable. Table is indexed by RF Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexEasServerApplyEntry

apexEasServerApplyEntry 1.3.6.1.4.1.1166.1.31.21.1.3.1
EAS Server Configuration Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexEasServerApplyEntry  

apexEasServerApplyNum 1.3.6.1.4.1.1166.1.31.21.1.3.1.1
The EAS Server number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

apexEasServerApplyChange 1.3.6.1.4.1.1166.1.31.21.1.3.1.2
The Apply for a row in the apexEasServerTable. This parameter MUST be set to 'apply' in order for any of the data in the apexEasServerTable table to take effect. This parameter MUST be set LAST after all other data in the table has been configured. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexEasServerTable 1.3.6.1.4.1.1166.1.31.21.1.4
Table of parameters for configuring EAS Servers. Table is indexed by RF Port number. @Config(config=yes, reboot=no) @Commit(param=apexEasServerApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexEasServerEntry

apexEasServerEntry 1.3.6.1.4.1.1166.1.31.21.1.4.1
A row in the EAS server table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexEasServerEntry  

apexEasServerNum 1.3.6.1.4.1.1166.1.31.21.1.4.1.1
The EAS Server number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

apexEasServerPhysInType 1.3.6.1.4.1.1166.1.31.21.1.4.1.2
Input Type of input from which to extract EAS messages. When set to 0, no EAS is received (disables EAS extraction). Once written, the change to this parameter will only take immediate effect after apexEasServerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(0), gbe(1), fastEnet(2)  

apexEasServerPhysInPort 1.3.6.1.4.1.1166.1.31.21.1.4.1.3
Number of the input, of type configured by apexEasServerPhysInType, from which to extract EAS messages. Once written, the change to this parameter will only take immediate effect after apexEasServerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Range(min=0)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

apexEasServerRcvUdpPort 1.3.6.1.4.1.1166.1.31.21.1.4.1.4
This parameter indicates the UDP port on which to receive EAS messages. Range is 1024 to 65535 when apexEasServerPhysInType is 'fastEnet'. Range is 0 to 65535 when apexEasServerPhysInType is 'gbe'. Once written, the change to this parameter will only take immediate effect after apexEasServerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexEasServerMulticastIpAddress 1.3.6.1.4.1.1166.1.31.21.1.4.1.5
This parameter indicates the Multicast IP Receive address on which to receive EAS messages. If 0.0.0.0, then EAS messages will be received via singlecast only. Once written, the change to this parameter will only take immediate effect after apexEasServerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexEasServerSourceIpAddress 1.3.6.1.4.1.1166.1.31.21.1.4.1.6
This parameter indicates the Source IP Receive address on which to receive EAS messages. This is only for IGMP v3 networks. If 0.0.0.0, then source IP is not used. Once written, the change to this parameter will only take immediate effect after apexEasServerApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexEasNumRcvMsgs 1.3.6.1.4.1.1166.1.31.21.2.1.1
Total number of EAS messages received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexEasNumInvalRcvMsgs 1.3.6.1.4.1.1166.1.31.21.2.1.2
Total number of Invalid EAS messages received (invalid CRC). These messages are discarded.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexChassisRedundancyConfigEnable 1.3.6.1.4.1.1166.1.31.22.1.1.1
This is to enable/disable APEX chassis redundancy. When set to disabled(1), APEX is not allowed to failover. When set to enabled(2), APEX can failover on its redundant APEX. Once written, the change to this parameter will only take immediate effect after apexChassisRedundancyConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyMode 1.3.6.1.4.1.1166.1.31.22.1.1.2
Configures the desired role of APEX. Primary has active output ports, secondary is inactive with output ports muted. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

apexChassisRedundancyMulticastRedundancyMode 1.3.6.1.4.1.1166.1.31.22.1.1.3
This is used to process route mappings by the standby APEX. When set to hot(0) on standby APEX, all the routes processed by the active APEX will also be processed by standby APEX. When set to warm(1) on standby APEX, all the routes processed by the active APEX will be muted by standby APEX. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER hot(1), warm(2)  

apexChassisRedundancyUdpPort 1.3.6.1.4.1.1166.1.31.22.1.1.4
This UDP port number value is used as: (1) The port number on which to receive heartbeat messages from the redundant APEX (2) The port number to which heartbeat messages are sent to the redundant APEX. Valid range of UDP port numbers are 1024 to 65535. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1024..65535  

apexChassisRedundancyRedundantApexIp 1.3.6.1.4.1.1166.1.31.22.1.1.5
Unicast IP address of redundant APEX. This IP address is used to send heartbeat messages to the redundant IP. This IP address should match with the ENET1 or ENET2 IP address of the redundant APEX. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexChassisRedundancySuspend 1.3.6.1.4.1.1166.1.31.22.1.1.6
When set to enabled(2), this results in APEX unit failover and become active if it is in standby or suspend state. If the condition above is not met, setting the value to enabled(2) has no effect. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyForceFailOver 1.3.6.1.4.1.1166.1.31.22.1.1.7
When set to failover(2), this results in the APEX unit failing over if it is in active state and the redundant APEX is in standby state. If the condition above is not met, setting the value to failvoer(2) has no effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER failoverNotInProgress(1), failover(2)  

apexChassisRedundancyFailOverGigE12LinkLoss 1.3.6.1.4.1.1166.1.31.22.1.1.8
Configures if both GigE 1&2 link loss is cause for a failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyFailOverGigE34LinkLoss 1.3.6.1.4.1.1166.1.31.22.1.1.9
Configures if both GigE 3&4 experience link loss is cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyFailOverEnet1LinkLoss 1.3.6.1.4.1.1166.1.31.22.1.1.10
Configures if ENET1 link loss is cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyFailOverEnet2LinkLoss 1.3.6.1.4.1.1166.1.31.22.1.1.11
Configures if ENET2 link loss is cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyFailOverTemperatureFault 1.3.6.1.4.1.1166.1.31.22.1.1.12
Configures if the temperature fault is a cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyFailOverQamModuleFault 1.3.6.1.4.1.1166.1.31.22.1.1.13
Configures if a QAM module fault is a cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyFailOverQamRfPortFault 1.3.6.1.4.1.1166.1.31.22.1.1.14
Configures if a QAM RF port fault is a cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyFailOverQamChannelFault 1.3.6.1.4.1.1166.1.31.22.1.1.15
Configures if a QAM channel fault is a cause for failover. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyConfigApplyChange 1.3.6.1.4.1.1166.1.31.22.1.1.16
The Apply for Chassis Redundancy Configuration parameters. This parameter MUST be set to 'apply' in order for the data to take effect. This parameter MUST be set LAST after all Chassis Redundancy parameters affected by this parameter have been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexChassisRedundancyPrimaryStandbyOverride 1.3.6.1.4.1.1166.1.31.22.1.1.17
This parameter is set to ENABLED while configuring the apex as primary apex. If this parameter is set, the apex will goto ACTIVE state irrespective of secondary status. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyRedundantApexSecIp 1.3.6.1.4.1.1166.1.31.22.1.1.18
Unicast IP address of redundant APEX heartbeat backup interface. This IP address is used to send backup heartbeat messages to the redundant IP. This IP address should match with the ENET1 or ENET2 IP address of the redundant APEX. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexChassisRedundancyRedundantHBEnable 1.3.6.1.4.1.1166.1.31.22.1.1.19
This parameter is set to ENABLED to configure backup heartbeat interface IP. Heartbeat message in the Backup heartbeat interface is used if the Primary heartbeat inteface fails. @Config(config=yes, reboot=no) @Commit(param=apexChassisRedundancyConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexChassisRedundancyPrimaryApexStatus 1.3.6.1.4.1.1166.1.31.22.2.1.1
This parameter is applicable for an APEX where chassis redundancy is enabled. The APEX configured as primary will report the following values: active(1): Primary RF outputs are active. standby(2): Primary RF outputs are muted. Waiting to become active. fault(3): Primary has experienced a fault. suspend(4): Primary is suspended. The APEX configured as secondary will report the following values. These are based on its knowledge about the primary APEX from heartbeat messages. unknown(0): State of primary is not known (heartbeat not received). active(1): Primary RF outputs are active. standby(2): Primary RF outputs are muted. Waiting to become active. fault(3): Primary has experienced a fault. suspend(4): Primary is suspended.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), active(1), standby(2), fault(3), suspend(4)  

apexChassisRedundancySecondaryApexStatus 1.3.6.1.4.1.1166.1.31.22.2.1.2
This parameter is applicable for an APEX where chassis redundancy is enabled. The APEX configured as primary will report the following values: These are based on its knowledge about the secondary APEX from heartbeat messages. unknown(0): State of secondary is not known (heartbeat not received). active(1): Secondary RF outputs are active. standby(2): Secondary RF outputs are muted. Waiting to become active. fault(3): Secondary has experienced a fault. suspend(4): Secondary is suspended. The APEX configured as secondary will report the following values: active(1): Secondary RF outputs are active. standby(2): Secondary RF outputs are muted. Waiting to become active. fault(3): Secondary has experienced a fault. suspend(4): Secondary is suspended.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), active(1), standby(2), fault(3), suspend(4)  

apexChassisRedundancyState 1.3.6.1.4.1.1166.1.31.22.2.1.3
This parameter is applicable for an APEX where chassis redundancy is enabled. This parameter will report the chassis redundancy availability status. These are based on its knowledge about the secondary APEX from heartbeat messages. The APEX configured as primary will report the following values: unknown(0): State of redundancy is not known (heartbeat not received). available(1): Primary is active and secondary is in standby, configurations are synchronized and no critical faults on either of the APEX. protected(2): Primary is fault and secondary is in active. unavailable(3): Configuration not synchronized or primary has not received heartbeat message from secondary. synchronizing(4): Synchronizing configuration between active and standby APEX's. The APEX configured as secondary will report the following values: unknown(0): State of redundancy is not known (heartbeat not received). available(1): Secondary is active and primary is in standby, configurations are synchronized and no critical faults on either of the APEX. protected(2): Secondary is in active and primary is fault state. unavailable(3): Configuration not synchronized or secondary is in fault state or secondary has not received heartbeat message from primary. synchronizing(4): Synchronizing configuration between active and standby APEX's.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), available(1), protected(2), unavailable(3), synchronizing(4)  

apexChassisRedundancyCommunicationStatus 1.3.6.1.4.1.1166.1.31.22.2.1.4
This parameter is applicable for an APEX where chassis redundancy is enabled. This parameter will report the chassis redundancy communication status. These are based on its knowledge about the secondary APEX from heartbeat messages. The APEX configured as primary will report the following values: disconnected(0): No heartbeat messages are received from secondary or communication timed out. connected(1): Heartbeat messages are received from secondary and communication has not timed out. The APEX configured as secondary will report the following values: disconnected(0): No heartbeat messages are received from primary or communication timed out. connected(1): Heartbeat messages are received from primary and communication has not timed out.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disconnected(0), connected(1)  

apexChassisRedundancyConfigurationStatus 1.3.6.1.4.1.1166.1.31.22.2.1.5
This parameter is applicable for an APEX where chassis redundancy is enabled. This parameter will report the chassis redundancy configuration status. These are based on its knowledge about the secondary APEX from heartbeat messages. The APEX configured as primary will report the following values: unknown(0): Secondary configuration is not known or secondary is not connected. synchronized(1): Secondary has same configuration as primary (except for QAM outputs). outofsync(2): Secondary configuration is not in sync with primary. The APEX configured as secondary will report the following values: unknown(0): Primary configuration is not known or primary is not connected. synchronized(1): Primary has same configuration as secondary (except for QAM outputs). outofsync(2): Primary configuration is not in sync with secondary.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), synchronized(1), outofsync(2)  

apexChassisRedundancyStatusInvalidApplyText 1.3.6.1.4.1.1166.1.31.22.2.1.6
When apexChassisRedundancyConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexChassisRedundancyGeneralConfigSyncStatusText 1.3.6.1.4.1.1166.1.31.22.2.1.7
GigE Config Sync Error info
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexChassisRedundancyGigEMismatchStatus 1.3.6.1.4.1.1166.1.31.22.2.1.8
This parameter indicates whether the GigE configuration of the apexes in Chassis Redundancy pair match. Both the APEXs will report the following values: These are based on its knowledge about the secondary APEX GigE configuration from heartbeat messages. unknown (0): GigE configuration of pair APEX is not known (heartbeat not received). match (1): GigE configuration of APEXs in redundancy pair match. mismatch (2): GigE configuration of APEXs in redundancy pair do not match.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), match(1), mismatch(2)  

apexChassisRedundancyQamMismatchStatus 1.3.6.1.4.1.1166.1.31.22.2.1.9
This parameter indicates whether the QAM configuration of the apexes in Chassis Redundancy pair match. Both the APEXs will report the following values: These are based on its knowledge about the secondary APEX QAM configuration from heartbeat messages. unknown (0): QAM configuration of pair APEX is not known (heartbeat not received). match (1): QAM configuration of APEXs in redundancy pair match. mismatch (2): QAM configuration of APEXs in redundancy pair do not match.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), match(1), mismatch(2)  

apexChassisRedundancyFirmwareMismatchStatus 1.3.6.1.4.1.1166.1.31.22.2.1.10
This parameter indicates whether the Firmware version of the apexes in Chassis Redundancy pair match. Both the APEXs will report the following values: These are based on its knowledge about the secondary APEX Firmware version from heartbeat messages. unknown (0): Firmware version of pair APEX is not known (heartbeat not received). match (1): Firmware version of APEXs in redundancy pair match. mismatch (2): Firmware version of APEXs in redundancy pair do not match.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), match(1), mismatch(2)  

apexChassisRedundancyGigE12LinkStatus 1.3.6.1.4.1.1166.1.31.22.2.1.11
This parameter indicates the combined alarm status of the GigE 1 and GigE 2. Indicates the lower of the gigE input interface alarm conditions. ok (1): No alarm on either of GigE1 and GigE2. warning (3): Warning alarm on both GigE1 or GigE2 minor (4): minor alarm on both GigE1 or GigE2 major (5): Major alarm on both GigE1 or GigE2 critical (6): critical alarm on both GigE1 and GigE2.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexChassisRedundancyGigE34LinkStatus 1.3.6.1.4.1.1166.1.31.22.2.1.12
This parameter indicates the combined alarm status of the GigE3 and GigE4. Indicates the lower of the gigE input interface alarm conditions. ok (1): No alarm on either of GigE3 and GigE4. warning (3): Warning alarm on both GigE3 or GigE4 minor (4): minor alarm on both GigE3 or GigE4 major (5): Major alarm on both GigE3 or GigE4 critical (6): critical alarm on both GigE3 and GigE4.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexChassisRedundancyCurrHBIntfIPStatus 1.3.6.1.4.1.1166.1.31.22.2.1.13
This parameter indicates the heartbeat interface used for receiving heartbeat from the redundant APEX.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexDtaGeneralConfigCatSourceType 1.3.6.1.4.1.1166.1.31.23.1.1.1
When set to internal(0), APEX generates CAT and inserts EMM pid received from DAC. When set to external(1), APEX will not generate CAT, it will receive both CAT and EMM pids from DAC and inserts EMM pid into CAT. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

apexDtaGeneralConfigCatEmmPidMulticastIP 1.3.6.1.4.1.1166.1.31.23.1.1.2
Multicast IPv4 address on which CAT/EMM PID stream is available. An IP Address of 0.0.0.0 indicates unicast stream. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexDtaGeneralConfigCatEmmPidSourceIP 1.3.6.1.4.1.1166.1.31.23.1.1.3
Source IP address to receive CAT/EMM PID stream. This is used only if apexQamRfConfigDtaNetworkPidMulticastIP is set to a multicast address. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexDtaGeneralConfigCatEmmPidUdpPort 1.3.6.1.4.1.1166.1.31.23.1.1.4
UDP port to receive CAT/EMM PID stream. The range of valid UDP port numbers are 1024 to 65535. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1024..65535  

apexDtaGeneralConfigCatEmmPidInterface 1.3.6.1.4.1.1166.1.31.23.1.1.5
Fast Ethernet Interface to receive CAT/EMM PID stream. One of ENET1 and ENET2 interfaces are used to receive CAT/EMM PID streams. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EthernetInterfaceTYPE  

apexDtaGeneralConfigEmmPidNum 1.3.6.1.4.1.1166.1.31.23.1.1.6
EMM PID to insert on DTA enabled OTS. The range of valid PID numbers are 0x1C00 to 0x1FFE. @Config(config=yes, reboot=no) @Commit(param=apexDtaGeneralConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 7168..8190  

apexDtaGeneralConfigApplyChange 1.3.6.1.4.1.1166.1.31.23.1.1.7
The Apply for DTA Configuration parameters. This parameter MUST be set to 'apply' in order for the DTA Cat Config data to take effect. This parameter MUST be set LAST after all DTA Config parameters affected by this parameter have been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexDtaGeneralConfigInvalidApplyText 1.3.6.1.4.1.1166.1.31.23.1.1.8
When apexDtaGeneralConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with DTA CAT/EMM PID Config data or NET PID Config data.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexDtaConfigApplyTable 1.3.6.1.4.1.1166.1.31.23.1.2
Apply table for the configuration tables apexDtaRfPortConfigTable and apexDtaOtsConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexDtaConfigApplyEntry

apexDtaConfigApplyEntry 1.3.6.1.4.1.1166.1.31.23.1.2.1
DTA RF Port Configuration Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexDtaConfigApplyEntry  

apexDtaConfigApplyIndex 1.3.6.1.4.1.1166.1.31.23.1.2.1.1
Defines the size of apexDtaRfPortConfigTable. DTA NET PID can be configured for each RF port. This shall be the number of maximum number of QAM RF port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

apexDtaConfigApplyChange 1.3.6.1.4.1.1166.1.31.23.1.2.1.2
The Apply for a row of data in apexDtaRfPortConfigTable. The Apply for eight rows of data in apexDtaOtsConfigTable. A row in this table corresponds to the same row index in the apexDtaRfPortConfigTable. A row in this table corresponds to eight rows in the apexDtaOtsConfigTable when QAM module is type of either 2x4 or 2x8 as follows: Apply Table DTA OTS/QAM Config Table ----------- ----------------- 1 1-8 2 9-16 3 17-24 4 25-32 5 33-40 6 41-48 A row in this table corresponds to four rows in the apexDtaOtsConfigTable when QAM module is type of 4x4 as follows: Apply Table DTA OTS/QAM Config Table ----------- ----------------- 1 1-4 2 5-8 3 17-20 4 21-24 5 33-36 6 37-40 7 9-12 8 13-16 9 25-28 10 29-32 11 41-44 12 45-48 This parameter MUST be set to 'apply' in order for any of the data in the rows to take effect in the APEX. This parameter MUST be set LAST after all other data in the configuration table rows has been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexDtaRfPortConfigTable 1.3.6.1.4.1.1166.1.31.23.1.3
Table of DTA configuration items configurable on a RF Port basis. Once written, the change to this table will only take immediate effect after apexDtaConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexDtaConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexDtaRfPortConfigEntry

apexDtaRfPortConfigEntry 1.3.6.1.4.1.1166.1.31.23.1.3.1
DTA RF port configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexDtaRfPortConfigEntry  

apexDtaRfPortConfigIndex 1.3.6.1.4.1.1166.1.31.23.1.3.1.1
The QAM RF Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

apexDtaRfPortConfigNetPidMulticastIP 1.3.6.1.4.1.1166.1.31.23.1.3.1.2
Multicast IPv4 address on which Network PID stream is available. An IP Address of 0.0.0.0 indicates unicast stream.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexDtaRfPortConfigNetPidSourceIP 1.3.6.1.4.1.1166.1.31.23.1.3.1.3
Source IP address to receive Network PID stream. This is used only if apexDtaRfPortConfigNetPidMulticastIP is set to a multicast address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexDtaRfPortConfigNetPidUdpPort 1.3.6.1.4.1.1166.1.31.23.1.3.1.4
UDP port number to receive Network PID stream. The range of valid port numbers are 1024 to 65535.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1024..65535  

apexDtaRfPortConfigNetPidInterface 1.3.6.1.4.1.1166.1.31.23.1.3.1.5
Fast Ethernet Interface to receive Network PID stream. Network PID stream can be received either ENET1 or ENET2.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetInterfaceTYPE  

apexDtaRfPortConfigNetPidNum 1.3.6.1.4.1.1166.1.31.23.1.3.1.6
Network PID to insert on DTA enabled OTS. The range of valid PID numbers are 0x1C00 to 0x1FFE.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 7168..8190  

apexDtaOtsConfigTable 1.3.6.1.4.1.1166.1.31.23.1.4
Table of DTA configuration items for output transport streams (OTS). Once written, the change to this table will only take immediate effect after apexDtaConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexDtaConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexDtaOtsConfigEntry

apexDtaOtsConfigEntry 1.3.6.1.4.1.1166.1.31.23.1.4.1
DTA OTS enable configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexDtaOtsConfigEntry  

apexDtaOtsConfigIndex 1.3.6.1.4.1.1166.1.31.23.1.4.1.1
The Output Transport Stream(OTS) number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexDtaOtsConfigEnable 1.3.6.1.4.1.1166.1.31.23.1.4.1.2
This is to enable/disable of inserting DTA messages on OTS. When set to disabled(1), DTA messages are not allowed to insert on OTS. When set to enabled(2), DTA messages are allowed to insert on OTS.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexDepiConfigHostname 1.3.6.1.4.1.1166.1.31.24.1.1.1
Host name defined as the FQDM of the APEX-EQAM device. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2, default=yes) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

apexDepiStatusGeneralDtiPort1LinkActive 1.3.6.1.4.1.1166.1.31.24.2.1.1
This indicates if the DTI Ethernet link is active.
Status: current Access: read-only
OBJECT-TYPE    
  ActiveTYPE  

apexDepiStatusGeneralDtiPort2LinkActive 1.3.6.1.4.1.1166.1.31.24.2.1.2
This indicates if the second DTI Ethernet link is active.
Status: current Access: read-only
OBJECT-TYPE    
  ActiveTYPE  

apexDepiStatusGeneralDtiClientStatusMode 1.3.6.1.4.1.1166.1.31.24.2.1.3
The DTI Client MUST support and report these operational modes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER warmup(1), free-run(2), fast(3), normal(4), bridging(5), holdover(6)  

apexDepiStatusGeneralDtiClientPhaseError 1.3.6.1.4.1.1166.1.31.24.2.1.4
24-bit Phase Error in units of 149.8 MHz sample clock cycles. The lower eight bits of the 24-bit field MUST be padded with zeros and MUST NOT be used by the DTI server. The value MUST be a signed 2's complement number. If the DTI client supports more bits of resolution, the DTI client MUST round the reported value to the nearest integer sample clock cycle.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiStatusGeneralDtiCurrentTimestamp 1.3.6.1.4.1.1166.1.31.24.2.1.5
DOCSIS 32-bit timestamp (DTS).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiStatusGeneralDtiPort1CableAdvanceValue 1.3.6.1.4.1.1166.1.31.24.2.1.6
24-bit Cable Advance value is derived by dividing the cable delay by 2.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiStatusGeneralDtiPort2CableAdvanceValue 1.3.6.1.4.1.1166.1.31.24.2.1.7
24-bit Cable Advance value is derived by dividing the cable delay by 2.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiControlConfigGeneralKeepaliveTimeout 1.3.6.1.4.1.1166.1.31.24.3.1.1.1
Timeout in seconds to wait while no control or data messages are received within the connection before sending a DEPI:HELLO message. Default is 60 seconds. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..600  

apexDepiControlConfigApplyTable 1.3.6.1.4.1.1166.1.31.24.3.1.2
Table of Apply Change for the data for apexDepiControlConfigTable. Entries in the apexDepiControlConfigTable cannot be modified while DEPI Control Connections and DEPI Sessions currently exist.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexDepiControlConfigApplyEntry

apexDepiControlConfigApplyEntry 1.3.6.1.4.1.1166.1.31.24.3.1.2.1
DEPI Control Configuration Apply Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexDepiControlConfigApplyEntry  

apexDepiControlConfigApplyIndex 1.3.6.1.4.1.1166.1.31.24.3.1.2.1.1
The index of the Depi Control Config Apply Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..10  

apexDepiControlConfigApplyChange 1.3.6.1.4.1.1166.1.31.24.3.1.2.1.2
The Apply for any entries in the apexDepiControlConfigTable. Entries in the apexDepiControlConfigTable cannot be modified while DEPI Control Connections and DEPI Sessions currently exist. This parameter MUST be set to 'apply' in order for any of the data in the apexDepiControlConfigTable to take effect. This parameter MUST be set LAST after all other data in the group has been configured. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexDepiControlConfigTable 1.3.6.1.4.1.1166.1.31.24.3.1.3
This table provides a list of DEPI Control Connections initiated by M-CMTS Cores. A maximum of 10 connections is accepted. Entries in the apexDepiControlConfigTable cannot be modified while DEPI Control Connections and DEPI Sessions currently exist. @Config(config=yes, reboot=no) @Commit(param=apexDepiControlConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexDepiControlConfigEntry

apexDepiControlConfigEntry 1.3.6.1.4.1.1166.1.31.24.3.1.3.1
DEPI Control Configuration Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexDepiControlConfigEntry  

apexDepiControlConfigIndex 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.1
The index of the Depi Control Config Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..10  

apexDepiControlConfigEnable 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.2
The enable setting for DEPI Control Connection. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexDepiControlConfigInterfaceNumber 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.3
Represents the Gigabit Ethernet interface number. Range: '0' = Not Applicable GBE = 1-4
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4  

apexDepiControlConfigSrcIpAddr 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.4
This parameter indicates the M-CMTS Core IP address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

apexDepiControlConfigOverUdp 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.5
This parameter indicates whether the DEPI Control Connection and Sessions will be accepted over the UDP protocol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER over-IP(1), over-UDP(2)  

apexDepiControlConfigType 1.3.6.1.4.1.1166.1.31.24.3.1.3.1.6
This parameter indicates whether DEPI Sessions are established dynamically using the DEPI control protocol or statically. Not supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

apexDepiControlStatusGeneralTotalConnections 1.3.6.1.4.1.1166.1.31.24.3.2.1.1
The number of DEPI Control Connections established since reboot.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiControlStatusGeneralCurrentConnections 1.3.6.1.4.1.1166.1.31.24.3.2.1.2
The current number of DEPI Control Connections currently connected.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..10  

apexDepiControlStatusGeneralRejectedConnections 1.3.6.1.4.1.1166.1.31.24.3.2.1.3
The number of control connection requests rejected for any reason.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiControlStatusGeneralUnknownConnectionMessages 1.3.6.1.4.1.1166.1.31.24.3.2.1.4
The number of DEPI control messages ignored not related to any existing control connection i.e. unrecognized connection identifier.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiControlStatusGeneralUnknownSessionMessages 1.3.6.1.4.1.1166.1.31.24.3.2.1.5
The number of DEPI messages ignored not related to any existing session i.e. unrecognized session identifier.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiControlStatusGeneralInvalidApplyText 1.3.6.1.4.1.1166.1.31.24.3.2.1.6
When apexDepiControlConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexDepiControlStatusTable 1.3.6.1.4.1.1166.1.31.24.3.2.2
Table of read-only status information pertaining to the DEPI Control Connections.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexDepiControlStatusEntry

apexDepiControlStatusEntry 1.3.6.1.4.1.1166.1.31.24.3.2.2.1
DEPI Control Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexDepiControlStatusEntry  

apexDepiControlStatusIndex 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.1
DEPI Session ID
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..10  

apexDepiControlStatusLocalUdp 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.2
The EQAM UDP port used in DEPI session messages from M-CMTS core. Only valid for DEPI connections using L2TPv3/UDP/IP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiControlStatusRemoteUdp 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.3
The M-CMTS UDP port used in DEPI session messages from M-CMTS core. Only valid for DEPI connections using L2TPv3/UDP/IP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiControlStatusConnectionStatus 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.4
M-CMTS core to the EQAM control connection status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER terminated(1), failed(2), waiting(3), established(4)  

apexDepiControlStatusUnknownCtl 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.5
Number of unrecognized DEPI messages not marked as mandatory received on this control connection.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiControlStatusMalformedCtl 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.6
Number of malformed DEPI messages received on this control connection.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiControlStatusUnknownAvp 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.7
Number of messages received on this control connection with an unsupported AVP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiControlStatusMalformedAvp 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.8
Number of messages received on this control connection with malformed AVP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiControlStatusInvalidVendorId 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.9
Number of messages with an unsupported Vendor ID received on this control connection. The supported vendor IDs are 0 or 4491.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiControlStatusHbitSet 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.10
Number of messages received on this control connection with H-bit set to 1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiControlStatusTotalSessions 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.11
Total number of sessions established on this control connection since EQAM reboot. Only valid for dynamically established connections.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiControlStatusCurrentSessions 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.12
Number of session currently established on this control connection. Only valid for dynamically established connections.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiControlStatusRejectedSessions 1.3.6.1.4.1.1166.1.31.24.3.2.2.1.13
Number of session setup related (ICQR/ICCN) messages rejected on this control connection.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionConfigApplyTable 1.3.6.1.4.1.1166.1.31.24.4.1.1
Table of Apply Change for the data for apexDepiSessionConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexDepiSessionConfigApplyEntry

apexDepiSessionConfigApplyEntry 1.3.6.1.4.1.1166.1.31.24.4.1.1.1
DEPI Session Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexDepiSessionConfigApplyEntry  

apexDepiSessionConfigApplyOutputTsNum 1.3.6.1.4.1.1166.1.31.24.4.1.1.1.1
The index of the Depi Session Config Apply Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexDepiSessionConfigApplyChange 1.3.6.1.4.1.1166.1.31.24.4.1.1.1.2
The Apply for any entries in the apexDepiSessionConfigTable. This parameter MUST be set to 'apply' in order for any of the data in the apexDepiSessionConfigTable to take effect. This parameter MUST be set LAST after all other data in the table entry has been configured. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexDepiSessionConfigTable 1.3.6.1.4.1.1166.1.31.24.4.1.2
Table of data for DEPI Session Mapping. There are 48 rows in this table mapping QAM output TS to DEPI Session. Once written, the change to this table will only take immediate effect after apexDepiSessionConfigApplyChange is set to 'apply'. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via apexSaveConfig. @Config(config=yes, reboot=no) @Commit(param=apexDepiSessionConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexDepiSessionConfigEntry

apexDepiSessionConfigEntry 1.3.6.1.4.1.1166.1.31.24.4.1.2.1
DEPI Session Config Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexDepiSessionConfigEntry  

apexDepiSessionConfigOutputTsNum 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.1
The QAM output transport stream number which to associate the DEPI Session.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexDepiSessionConfigEnable 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.2
The enable setting for DEPI Session. Once written, the change to this parameter will take immediate effect. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter.
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexDepiSessionConfigControlId 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.3
DOCSIS Control ID assignment. Value of 0 indicates transport stream to be used for Video only.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10  

apexDepiSessionConfigDocsisTsid 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.4
The system wide unique M-CMTS TSID mapped to the QAM. This TSID is specified by the remote ID from the ICRQ message.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

apexDepiSessionConfigUdpPort 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.5
UDP port number defining the DEPI Session (if UDP is enabled.) The range of valid port numbers is 1 to 65535.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

apexDepiSessionConfigSyncCorrection 1.3.6.1.4.1.1166.1.31.24.4.1.2.1.6
Enable or disable updating the timestamp in the SYNC messages. This is only valid for static connections. (For dynamically established sessions, M-CMTS core enables or disables the SYNC correction during session establishment)
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexDepiSessionStatusGeneralInvalidApplyText 1.3.6.1.4.1.1166.1.31.24.4.2.1.1
When apexDepiSessionConfigApplyChange is set to 'applyNotInProgressInvalidData' this entry may contain a text description of what was wrong with the data. This entry contains the description for the most recent apply of a related entry that was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

apexDepiSessionStatusTable 1.3.6.1.4.1.1166.1.31.24.4.2.2
Table of read-only status information pertaining to the DEPI Sessions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexDepiSessionStatusEntry

apexDepiSessionStatusEntry 1.3.6.1.4.1.1166.1.31.24.4.2.2.1
DEPI Session Status Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexDepiSessionStatusEntry  

apexDepiSessionStatusIndex 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.1
DEPI Session ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexDepiSessionStatusControlId 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.2
The DEPI Control ID this session belongs to.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiSessionStatusOutputQAMChannel 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.3
The QAM Channel number this session is mapped to.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiSessionStatusLocalUdp 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.4
The local UDP port used by the APEX to communicate the DEPI Session messages to the M-CMTS Core
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiSessionStatusRemoteUdp 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.5
The remote UDP port used by the M-CMTS Core to communicate the DEPI Session messages to the Apex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiSessionStatusStatus 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.6
M-CMTS core to the EQAM control connection status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER terminated(1), failed(2), waiting(3), established(4)  

apexDepiSessionStatusPerHopBehavior 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.7
Per Hop Behavior value for this session.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexDepiSessionStatusUnknownCtl 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.8
Number of unrecognized DEPI messages not marked as mandatory received on this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusMalformedCtl 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.9
Number of malformed DEPI messages received on this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusUnknownAvp 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.10
Number of messages received on this session with an unsupported AVP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusMalformedAvp 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.11
Number of messages received on this session with malformed AVP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusInvalidVendorId 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.12
Number of messages with an unsupported Vendor ID received on this session. The supported vendor IDs are 0 or 4491.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusHbitSet 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.13
Number of messages received on this session with H-bit set to 1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusInSLIMsgs 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.14
Number of SLI messages received on this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusOutSLIMsgs 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.15
Number of SLI messages sent on this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusIngressDlmMsgs 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.16
Number of DLM messages received on this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusEgressDlmMsgs 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.17
Number of DLM messages sent on this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusLatencyStart 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.18
Last latency related timestamp start value received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusLatencyEnd 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.19
Last latency related timestamp end value received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusInDataPackets 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.20
Number of data packets received on this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusInSequenceDiscards 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.21
Number of data packets received on this session that are discarded due to sequencing error.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusInDataPacketDiscards 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.22
Number of data packets received on this session that are discarded for reasons other than sequencing errors.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexDepiSessionStatusSessionID 1.3.6.1.4.1.1166.1.31.24.4.2.2.1.23
Remote DEPI Session ID, used by the Remote End to identify the DEPI Session and locally to bind the Session to a QAM Channel.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexPsipConfigApplyChange 1.3.6.1.4.1.1166.1.31.25.1.1.1
The Apply for parameters in apexPsipConfigGeneral. This parameter MUST be set to 'apply' in order for other apexPsipConfigGeneral parameters to take effect. This parameter MUST be set LAST after other apexPsipConfigGeneral parameters have been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexPsipConfigMgtMsgInsertionPeriod 1.3.6.1.4.1.1166.1.31.25.1.1.2
Specify insertion rate (ms) for MGT PSIP table. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 150..1000  

apexPsipConfigSttMsgInsertionPeriod 1.3.6.1.4.1.1166.1.31.25.1.1.3
Specify insertion rate (ms) for STT PSIP table. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..5000  

apexPsipConfigCvctMsgInsertionPeriod 1.3.6.1.4.1.1166.1.31.25.1.1.4
Specify insertion rate (ms) for CVCT PSIP table. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 400..1000  

apexPsipConfigRrtMsgInsertionPeriod 1.3.6.1.4.1.1166.1.31.25.1.1.5
Specify insertion rate (ms) for RRT PSIP table. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 30000..60000  

apexPsipConfigEit0InsertionPeriod 1.3.6.1.4.1.1166.1.31.25.1.1.6
EIT insertion rate (ms) of EIT-0. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 500..60000  

apexPsipConfigEit1InsertionPeriod 1.3.6.1.4.1.1166.1.31.25.1.1.7
EIT insertion rate (ms) of EIT-1. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 500..60000  

apexPsipConfigEit2InsertionPeriod 1.3.6.1.4.1.1166.1.31.25.1.1.8
EIT insertion rate (ms) of EIT-2. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 500..60000  

apexPsipConfigEit3InsertionPeriod 1.3.6.1.4.1.1166.1.31.25.1.1.9
EIT insertion rate (ms) of EIT-3. Once written, the change to this parameter will only take immediate effect after apexPsipConfigApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 500..60000  

apexPsipConfigTimeApplyChange 1.3.6.1.4.1.1166.1.31.25.1.2.1
The Apply for parameters in apexPsipConfigTime group. This parameter MUST be set to 'apply' in order for other apexPsipConfigTime parameters to take effect. This parameter MUST be set LAST after other apexPsipConfigTime parameters have been configured. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ApplyDataToDeviceTYPE  

apexPsipConfigTimeDsMonthIn 1.3.6.1.4.1.1166.1.31.25.1.2.2
Configurable month for entering DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..12  

apexPsipConfigTimeDsDayIn 1.3.6.1.4.1.1166.1.31.25.1.2.3
Configurable day for entering DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..31  

apexPsipConfigTimeDsHourIn 1.3.6.1.4.1.1166.1.31.25.1.2.4
Configurable hour for entering DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..18  

apexPsipConfigTimeDsMonthOut 1.3.6.1.4.1.1166.1.31.25.1.2.5
Configurable month for exiting DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..12  

apexPsipConfigTimeDsDayOut 1.3.6.1.4.1.1166.1.31.25.1.2.6
Configurable day for exiting DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..31  

apexPsipConfigTimeDsHourOut 1.3.6.1.4.1.1166.1.31.25.1.2.7
Configurable hour for exiting DST. Once written, the change to this parameter will only take immediate effect after apexPsipConfigTimeApplyChange is set to 'apply'. In order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Commit(param=apexPsipConfigTimeApplyChange, value=2) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..18  

apexPsipStatusInputTable 1.3.6.1.4.1.1166.1.31.25.2.2
The following table contains a list of messages that are being extracted from the input side.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexPsipStatusInputEntry

apexPsipStatusInputEntry 1.3.6.1.4.1.1166.1.31.25.2.2.1
PSIP Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexPsipStatusInputEntry  

apexPsipStatusInputIndex 1.3.6.1.4.1.1166.1.31.25.2.2.1.1
Indicates the input index for which this message applies.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..784  

apexPsipStatusInputPid 1.3.6.1.4.1.1166.1.31.25.2.2.1.2
Indicates the PID that this message is contained in.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..8191  

apexPsipStatusInputMessageType 1.3.6.1.4.1.1166.1.31.25.2.2.1.3
Indicates the PSIP message type. 199 - MGT 200 - TVCT 201 - CVCT 203 - EIT 202 - RRT 205 - STT
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

apexPsipStatusInputSourceId 1.3.6.1.4.1.1166.1.31.25.2.2.1.4
Indicates the Source Id of EIT tables. When a message is not specifically related to a program, this value is 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

apexPsipStatusInputSegment 1.3.6.1.4.1.1166.1.31.25.2.2.1.5
Indicates the segment number of this message. Otherwise this is 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..256  

apexPsipStatusInputPart 1.3.6.1.4.1.1166.1.31.25.2.2.1.6
Since a message can be 4096 bytes long the message may divided into parts. Each part of the message is indexed using this index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

apexPsipStatusInputBody 1.3.6.1.4.1.1166.1.31.25.2.2.1.7
Raw ASCII hex of the PSIP message.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexPsipStatusInputGpsTime 1.3.6.1.4.1.1166.1.31.25.2.2.1.8
The GPS time when the PSIP message was added to the table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexPsipStatusInputInfo 1.3.6.1.4.1.1166.1.31.25.2.2.1.9
Comma-separated string showing Input Interface, UDP port, Multicast IP, and Source IP for this PSIP message.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexPsipStatusOutputTable 1.3.6.1.4.1.1166.1.31.25.2.3
The following table contains a list of messages that are being inserted to the output side of the apex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexPsipStatusOutputEntry

apexPsipStatusOutputEntry 1.3.6.1.4.1.1166.1.31.25.2.3.1
PSIP Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexPsipStatusOutputEntry  

apexPsipStatusOutputIndex 1.3.6.1.4.1.1166.1.31.25.2.3.1.1
Indicates the Output index for which this message applies. This is the Output Transport Stream number (1..48).
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..48  

apexPsipStatusOutputPid 1.3.6.1.4.1.1166.1.31.25.2.3.1.2
Indicates the PID that this message is contained in.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..8191  

apexPsipStatusOutputMessageType 1.3.6.1.4.1.1166.1.31.25.2.3.1.3
Indicates the PSIP message type. 199 - MGT 200 - TVCT 201 - CVCT 203 - EIT 202 - RRT 205 - STT
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

apexPsipStatusOutputSourceId 1.3.6.1.4.1.1166.1.31.25.2.3.1.4
Indicates the Source Id of EIT tables. When a message is not specifically related to a program, this value is 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

apexPsipStatusOutputSegment 1.3.6.1.4.1.1166.1.31.25.2.3.1.5
Indicates the segment number of this message. Otherwise this is 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..256  

apexPsipStatusOutputPart 1.3.6.1.4.1.1166.1.31.25.2.3.1.6
Since a message can be 4096 bytes long the message may divided into parts. Each part of the message is indexed using this index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

apexPsipStatusOutputBody 1.3.6.1.4.1.1166.1.31.25.2.3.1.7
Raw ASCII hex of the PSIP message.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexPsipStatusOutputGpsTime 1.3.6.1.4.1.1166.1.31.25.2.3.1.8
The GPS time when the PSIP message was added to the table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexPsipStatusServiceTable 1.3.6.1.4.1.1166.1.31.25.2.4
The following table shows the PSIP status per service. For each service, the service number, the Output Transport Stream number, its PSIP state and its source id are shown in the current entry. This table is indexed the same as apexOutputProgramTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexPsipStatusServiceEntry

apexPsipStatusServiceEntry 1.3.6.1.4.1.1166.1.31.25.2.4.1
PSIP Status Table Entry per service.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexPsipStatusServiceEntry  

apexPsipStatusServiceIndex 1.3.6.1.4.1.1166.1.31.25.2.4.1.1
Output Program Table Index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..768  

apexPsipStatusServiceNum 1.3.6.1.4.1.1166.1.31.25.2.4.1.2
Current Output Service Number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexPsipStatusServiceOutputTs 1.3.6.1.4.1.1166.1.31.25.2.4.1.3
Current Output Transport Stream of this service.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..48  

apexPsipStatusServiceState 1.3.6.1.4.1.1166.1.31.25.2.4.1.4
Current program PSIP state.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

apexPsipStatusServiceSourceId 1.3.6.1.4.1.1166.1.31.25.2.4.1.5
Current PSIP Program Source Id.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

apexSupportPreencryptedSimulcrypt 1.3.6.1.4.1.1166.1.31.26.1.1.1
Allows to configure the APEX to support services pre-encrypted with Simulcrypt. All the CA descriptors present in the input PMT will be copied to the output PMT, modifying the ECM PID references if needed. Default value is enabled. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexAlarmHardwareFault 1.3.6.1.4.1.1166.1.31.100.8000
Indicates that a Hardware related error occurred. Examples include missing or uncommunicative HW, failures in initialization of HW, and failures to configure HW. These can occur at startup or when the system is operational. Types of HW Faults include: Application File(s) Download failure; SPI Interface Initialization failure; PCI Interface Initialization failure; GigE Configuration failure; MUX Configuration failure; QAM Module Communication failure; Unsupported/Incorrect HW/FW Version (QAM, etc.); Fatal Host Firmware Exception. 'critical' indicates a fatal error occurred that prevents the APEX from performing operational requirements. 'warning' indicates an error that does not prevent the APEX from performing operational requirements.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmInvalidInitData 1.3.6.1.4.1.1166.1.31.100.8001
Set when invalid Initialization data (ini files) is encountered.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmTemperatureFault 1.3.6.1.4.1.1166.1.31.100.8002
'critical' indicates one or more temperature sensors is reporting a high temperature condition.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmFanFault 1.3.6.1.4.1.1166.1.31.100.8003
'major' indicates one or more fans has reduced RPM readings.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmPowerFault 1.3.6.1.4.1.1166.1.31.100.8004
Power Supply Fault Alarm. 'warning' indicates power supply not compatible (apexPsStatusInstalled). 'major' indicates power supply or fan only module) removed (apexPsStatusInstalled). 'major' indicates power supply input power fault (apexPsStatusInputPowerStatus), output power fault (apexPsStatusOutputPowerStatus), or comm fault (apexPsStatusCommError). 'critical' indicates power supply over temperature fault (apexPsStatusTemperatureStatus).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmGbeLossOfPhysicalInput 1.3.6.1.4.1.1166.1.31.100.8020
Loss of Physical Gigabit Ethernet Input Alarm. 'critical' indicates that one or more physical interfaces that are configured as enabled to receive input have a failure (apexGbeStatusLossOfPhysicalInput). Physical input interfaces can be disabled to prevent this alarm when no input is connected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmGbeBufferFullness 1.3.6.1.4.1.1166.1.31.100.8021
Gigabit Ethernet Frame Buffer Fullness Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Frame buffers are about to or have overflowed. The overflow level is based on the actual input data rate. 'major' when the frame buffer crosses a user specified threshold (apexGbeConfigFrameBufferAlarmThreshold). Cleared when the buffer level drops below the threshold. 'critical' when the frame buffer is completely full and frames are being dropped. Cleared when the overflow condition stops. A Major alarm, depending on the threshold setting, indicates that the APEX is getting close to overflowing it's internal Gigabit Ethernet frame buffers. A Critical alarm indicates that the frame buffer levels have overflowed. This will cause loss of packets and may result in tiling and other output anomalies.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmGbeInputStreamLowBitRate 1.3.6.1.4.1.1166.1.31.100.8022
Gigabit Ethernet Input Stream Low Bit Rate Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Input Streams as configured in apexManRteGbeInRedTable have a low bit rate condition. For alarm status of each stream refer to entries apexGbeStatInTsPriLowBitRateAlarm and apexGbeStatInTsSecLowBitRateAlarm. 'major' when one or more stream bit rates are below their apexManRteGbeInRedPriLowAlarmBitRate or apexManRteGbeInRedSecLowAlarmBitRate. Clears when all streams have been restored to at or above their configured apexManRteGbeInRedPriLowAlarmBitRate or apexManRteGbeInRedSecLowAlarmBitRate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmGbeInputStreamHighBitRate 1.3.6.1.4.1.1166.1.31.100.8023
Gigabit Ethernet Input Stream High Bit Rate Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Input Streams as configured in apexManRteGbeInRedTable or via a Session Controller have a high bit rate condition. For alarm status of each stream refer to entry apexGbeStatInTsPriHighBitRateAlarm and apexGbeStatInTsSecHighBitRateAlarm. 'major' when one or more stream bit rates are above their apexManRteGbeInRedPriHighAlarmBitRate or apexManRteGbeInRedSecHighAlarmBitRate. Clears when all streams have been restored to at or below their configured apexManRteGbeInRedPriHighAlarmBitRate or apexManRteGbeInRedSecHighAlarmBitRate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmGbeMptsRedundPrimaryThreshold 1.3.6.1.4.1.1166.1.31.100.8024
Gigabit Ethernet Input MPTS Redundant Primary Stream Below Threshold Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Input Streams configured in apexManRteGbeInRedTable as being the Primary stream of a Redundant Pair are below the configured threshold. For alarm status of each stream refer to entry apexGbeStatInTsMptsRedundPriAlarm. 'major' when one or more stream bit rates are below their threshold as specified in apexManRteGbeInRedThreshold. Clears when all streams have been restored to at or above their configured apexManRteGbeInRedThreshold.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmGbeMptsRedundFailOver 1.3.6.1.4.1.1166.1.31.100.8025
Gigabit Ethernet Input MPTS Redundant Fail Over Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Input Streams configured in apexManRteGbeInRedTable as being the Primary stream of a Redundant Pair have Failed Over to the Secondary stream. For alarm status of each stream refer to entry apexGbeStatInTsMptsRedundFailAlarm. 'major' when one or more Redundant Primary streams have failed over to the Secondary. Clears when all Primary streams have been restored and the APEX has switched back to the Primary from the Secondary.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmServiceInError 1.3.6.1.4.1.1166.1.31.100.8026
Alarm Service In Error. 'major' indicates that one or more services is in error (unable to fully continue processing). However, this is only for very specific errors where the error could be caused by either the input stream being invalid or another command along with the input stream is causing the error. For example, if mapping an input service to an output and that PMT is not referenced in the PAT, or the number of PIDs in the PMT is greater than the number of PIDs supported, then the command is in error. This error condition would be cleared if a new PAT is received referencing the PMT or in the other case, if a new PMT is received referencing a valid number of PIDs. Refer to apexOutputProgramRoutingStatus for more information. This alarm occurs on the first error. It is not issued for additional errors. It is cleared when all errors are cleared.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmGbeLossOfInputStream 1.3.6.1.4.1.1166.1.31.100.8027
Loss of Gbe Input Stream Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet Input Streams is missing. A missing input stream is determined based on user configured data or stream rate and detection timeout value. This alarm is only applicable when the input streams are configured to be monitored for loss of input stream. This alarm occurs on the first error. It is not issued for additional errors. It is cleared when all errors are cleared.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmGigeToHostCommFault 1.3.6.1.4.1.1166.1.31.100.8028
Loss of Communications from Gige to Host Alarm. This alarm is used to inform the user when the Host processor is no longer receiving periodic status messages from the Gige processor. This alarm occurs on the first error. It is not issued for additional errors. It is cleared when the condition is resolved.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmGbeInterfaceRedundFailOver 1.3.6.1.4.1.1166.1.31.100.8029
Gigabit Ethernet Interface Redundant Fail Over Alarm. This alarm is used to inform the user when one or more Gigabit Ethernet interfaces have Failed Over to the Secondary interface. The APEX determines an interface as failed when link has been lost. 'major' when one or more Primary interfaces have failed over to the Secondary. Clears when all Primary interfaces have been restored and the APEX has switched back to the Primary from the Secondary.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmOutputUtilizationFault 1.3.6.1.4.1.1166.1.31.100.8040
Output Transport Stream Utilization Threshold Alarm. 'minor' when apexOutputTsUtilMonAlarmThreshold is met or exceeded for apexOutputTsUtilMonSetAlarmDelay for an OTS. The alarm will clear after the OTS remains below apexOutputTsUtilMonAlarmThreshold for apexOutputTsUtilMonClearAlarmDelay.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmOutputOverflow 1.3.6.1.4.1.1166.1.31.100.8041
Output Transport Stream Overflow Alarm. 'critical' when apexOutputTsUtilizOverflow occurs for an OTS. The alarm will clear when OTS no longer in overflow.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmQamModuleFault 1.3.6.1.4.1.1166.1.31.100.8042
QAM Port Fault Alarm. 'major' when apexQamModuleStatError occurs when all QAM channels on the QAM Module have apexQamChanStatActive of not 'active'. 'critical' when apexQamModuleStatError occurs when all QAM channels on the QAM Module have apexQamChanStatActive of 'active'. The alarm will clear after all faults clear on the QAM Module. The current alarm status on a QAM Module basis can be found in apexQamModuleStatFaultCondition.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmQamRfPortFault 1.3.6.1.4.1.1166.1.31.100.8043
QAM RF Port Fault Alarm. 'major' when power voltage or output RF level error occurs on the RF Port. 'critical' when clock, PLL, or data sync error occurs on the RF Port. The alarm will clear after all faults clear for the RF Port. The current alarm status on an RF port basis can be found in apexQamRfPortStatFaultCondition.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmQamChannelFault 1.3.6.1.4.1.1166.1.31.100.8044
QAM Channel Fault Alarm. 'critical' when any or all of the QAM Channel errors enumerated in apexQamChanStatError occur on a QAM channel. The alarm will clear after all faults clear on the QAM channel. The current alarm status on a QAM channel basis can be found in apexQamChanStatFaultCondition.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmQamRfRedundFailOver 1.3.6.1.4.1.1166.1.31.100.8045
QAM RF Redundancy Fail Over Alarm. 'major' when the backup QAM RF Port status is 'active' (apexQamRfRedundStatusBackupPort). This occurs when a primary QAM RF Port has failed over to the backup RF Port or the user has forced a primary to the backup. The alarm will clear when the backup QAM RF Port status returns to 'standby'. The alarm is relevant only when apexQamRfRedundConfigEnable is 'enabled'. The current QAM RF Port that is active on the backup port can be found in apexQamRfRedundStatusFailedPort.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmQamRfRedundMismatch 1.3.6.1.4.1.1166.1.31.100.8046
QAM RF Redundancy Mismatch Alarm. 'warning' when channels could be lost on QAM RF Fail Over to backup or on Switch Back to primary. Refer to apexQamRfRedundStatusMismatch for more information. The alarm will clear when mismatch condition clears. The alarm is relevant only when apexQamRfRedundConfigEnable is 'enabled'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmRtspControllerCommFault 1.3.6.1.4.1.1166.1.31.100.8050
RTSP Controller Communication Fault. 'major' when the RTSP Controller is experiencing a communication fault. The alarm will clear when connection is restored the RTSP controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmRdsCommFault 1.3.6.1.4.1.1166.1.31.100.8060
RDS Communication Fault. 'major' when experiencing an RDS communication fault. The alarm will clear when RDS connection is restored.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmRemCommFault 1.3.6.1.4.1.1166.1.31.100.8070
REM Communication Fault. 'major' when experiencing an REM communication fault. The alarm will clear when REM connection is restored. Refer to apexQamRfRedundStatusRemConnection for more information. The alarm is relevant only when apexQamRfRedundConfigEnable is 'enabled' and apexQamRfRedundConfigRemConnection is not 'none'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmRemFault 1.3.6.1.4.1.1166.1.31.100.8071
REM Fault. 'warning' when REM is reporting a 0x05 error code. 'major' when error received from REM (other than 0x05) or REM is reporting incorrect switch configuration. The alarm will clear when REM errors clear. Refer to apexQamRfRedundStatusRemError and apexQamRfRedundStatusRemSwitch for more information. The alarm is relevant only when apexQamRfRedundConfigEnable is 'enabled' and apexQamRfRedundConfigRemConnection is not 'none'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmDepiControlConnectionFault 1.3.6.1.4.1.1166.1.31.100.8080
DEPI Control connection setup Fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmDepiSessionSetupFault 1.3.6.1.4.1.1166.1.31.100.8081
DEPI Session Setup Fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmDtiSyncLossFault 1.3.6.1.4.1.1166.1.31.100.8082
EQAM lost SYNC with the DTI Server.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmChassisRedundancyPrimaryFailover 1.3.6.1.4.1.1166.1.31.100.8090
Generated when the primary active APEX fails over to the secondary standby unit. Trap tells if failover is operator induced, or automatic because of a fault. Major if automatic due to some fault Warning if force-failover. Cleared when redundancy is disabled or when the primary becomes active and the secondary is standby.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmChassisRedundancySecondaryFailover 1.3.6.1.4.1.1166.1.31.100.8091
Generated when the secondary active APEX fails over to the primary standby unit. Trap tells if failover is operator induced, or automatic because of a fault. Major if automatic due to some fault Warning if force-failover. Cleared when redundancy is disabled or when the secondary becomes active and the primary is standby.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmChassisRedundancyAvailabilityFault 1.3.6.1.4.1.1166.1.31.100.8092
Generated when redundancy status is unavailable (except for link loss) configuration not synchronized secondary in fault state Cleared when redundancy status is available or redundancy disabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmChassisRedundancyLinkFault 1.3.6.1.4.1.1166.1.31.100.8093
Generated when ENET2 link is lost Cleared when ENET 2 link is present or redundancy disabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexAlarmChassisRedundancyConfigurationFault 1.3.6.1.4.1.1166.1.31.100.8094
Generated when primary APEX receives heartbeat from another primary. Critical if APEX was in active state (sourcing broadcast content) Major if APEX was in standby state (broadcast ports muted). Cleared when primary APEX receives heartbeat from a secondary, configuration is changed to secondary, or redundancy is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexEventEmUserLoginFailed 1.3.6.1.4.1.1166.1.31.101.8100
Event to indicate APEX EM User login failed 5 times.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexEventQamModuleUpgraded 1.3.6.1.4.1.1166.1.31.101.8101
Event to indicate a QAM Module has been upgraded from 2x4 to 2x8 channel capability.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexEventChassisRedunPrimaryForceFailover 1.3.6.1.4.1.1166.1.31.101.8110
Generated when the operator forces a failover from the primary, back to the secondary APEX.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexEventChassisRedunSecondaryForceFailover 1.3.6.1.4.1.1166.1.31.101.8111
Generated when the operator forces a failover from the secondary, back to the primary APEX.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexEventChassisRedunFirmwareVersionMismatch 1.3.6.1.4.1.1166.1.31.101.8112
Generated when the primary and secondary APEX firmware versions are mismatched.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexEventChassisRedunQAMVersionMismatch 1.3.6.1.4.1.1166.1.31.101.8113
Generated when the primary and secondary APEX QAM versions are mismatched.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

apexEnableInvalidInitData 1.3.6.1.4.1.1166.1.31.102.1.8001
This setting enables or disables apexAlarmInvalidInitData. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableGbeLossOfPhysicalInput 1.3.6.1.4.1.1166.1.31.102.1.8020
This setting enables or disables apexAlarmGbeLossOfPhysicalInput. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableGbeBufferFullness 1.3.6.1.4.1.1166.1.31.102.1.8021
This setting enables or disables apexAlarmGbeBufferFullness. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableGbeInputStreamLowBitRate 1.3.6.1.4.1.1166.1.31.102.1.8022
This setting enables or disables apexAlarmGbeInputStreamLowBitRate. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableGbeInputStreamHighBitRate 1.3.6.1.4.1.1166.1.31.102.1.8023
This setting enables or disables apexAlarmGbeInputStreamHighBitRate. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableGbeMptsRedundPrimaryThreshold 1.3.6.1.4.1.1166.1.31.102.1.8024
This setting enables or disables apexAlarmGbeMptsRedundPrimaryThreshold. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableGbeMptsRedundFailOver 1.3.6.1.4.1.1166.1.31.102.1.8025
This setting enables or disables apexAlarmGbeMptsRedundFailOver. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableServiceInError 1.3.6.1.4.1.1166.1.31.102.1.8026
This setting enables or disables apexAlarmServiceInError. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableGbeLossOfInputTsFault 1.3.6.1.4.1.1166.1.31.102.1.8027
This setting enables or disables apexAlarmGbeLossOfInputStream. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableGbeInterfaceRedundFailOver 1.3.6.1.4.1.1166.1.31.102.1.8029
This setting enables or disables apexAlarmGbeInterfaceRedundFailOver. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableOutputUtilizationFault 1.3.6.1.4.1.1166.1.31.102.1.8040
This setting enables or disables apexAlarmOutputUtilizationFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableOutputOverflow 1.3.6.1.4.1.1166.1.31.102.1.8041
This setting enables or disables apexAlarmOutputOverflow. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableQamModuleFault 1.3.6.1.4.1.1166.1.31.102.1.8042
This setting enables or disables apexAlarmQamModuleFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableQamRfPortFault 1.3.6.1.4.1.1166.1.31.102.1.8043
This setting enables or disables apexAlarmQamRfPortFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableQamChannelFault 1.3.6.1.4.1.1166.1.31.102.1.8044
This setting enables or disables apexAlarmQamChannelFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableQamRfRedundFailOver 1.3.6.1.4.1.1166.1.31.102.1.8045
This setting enables or disables apexAlarmQamRfRedundFailOver. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableQamRfRedundMismatch 1.3.6.1.4.1.1166.1.31.102.1.8046
This setting enables or disables apexAlarmQamRfRedundMismatch. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableRtspControllerCommFault 1.3.6.1.4.1.1166.1.31.102.1.8050
This setting enables or disables apexAlarmRtspControllerCommFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableRdsCommAlarmFault 1.3.6.1.4.1.1166.1.31.102.1.8060
This setting enables or disables apexAlarmRdsCommFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableRemCommFault 1.3.6.1.4.1.1166.1.31.102.1.8070
This setting enables or disables apexAlarmRemCommFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableRemFault 1.3.6.1.4.1.1166.1.31.102.1.8071
This setting enables or disables apexAlarmRemFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableDepiControlConnectionFault 1.3.6.1.4.1.1166.1.31.102.1.8080
This setting enables or disables apexAlarmDepiControlConnectionFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableDepiSessionSetupFault 1.3.6.1.4.1.1166.1.31.102.1.8081
This setting enables or disables apexAlarmDepiSessionSetupFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableDtiSyncLossFault 1.3.6.1.4.1.1166.1.31.102.1.8082
This setting enables or disables apexAlarmDtiSyncLossFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableChassisRedundancyPrimaryFailover 1.3.6.1.4.1.1166.1.31.102.1.8090
This setting enables or disables apexEnableChassisRedundancyPrimaryFailover. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableChassisRedundancySecondaryFailover 1.3.6.1.4.1.1166.1.31.102.1.8091
This setting enables or disables apexEnableChassisRedundancySecondaryFailover. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableChassisRedundancyAvailabilityFault 1.3.6.1.4.1.1166.1.31.102.1.8092
This setting enables or disables apexEnableChassisRedundancyAvailabilityFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableChassisRedundancyLinkFault 1.3.6.1.4.1.1166.1.31.102.1.8093
This setting enables or disables apexEnableChassisRedundancyLinkFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexEnableChassisRedundancyConfigurationFault 1.3.6.1.4.1.1166.1.31.102.1.8094
This setting enables or disables apexEnableChassisRedundancyConfigurationFault. When set to 'enabled' the alarm will operate as described. When set to 'disabled' the alarm will not be reported or wrapped into unitAlarmStatus and the alarm condition will remain 'ok'. If the alarm condition is not 'ok' when it is 'disabled', the alarm will be cleared. Once written, the change to this parameter will take immediate effect. However, in order for the change to persist through subsequent reboots or power cycles, the change must be saved via the apexSaveConfig parameter. @Config(config=yes, reboot=no) @Save(apexSaveConfig, value=2) @File(config.ini, type='ini')
Status: current Access: read-write
OBJECT-TYPE    
  EnableDisableTYPE  

apexClearInvalidInitData 1.3.6.1.4.1.1166.1.31.102.2.8001
Setting to 'clearAlarm' clears the apexAlarmInvalidInitData. The APEX will set this parameter back to 'clearAlarmNotInProgress' after clearing the alarm. Once written, the change to this parameter will take immediate effect. @Config(config=no, reboot=no)
Status: current Access: read-write
OBJECT-TYPE    
  ClearAlarmTYPE  

apexHwEventTable 1.3.6.1.4.1.1166.1.31.200.1
Table of Hardware Events that have occurred. Maximum of 100 events will be recorded.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexHwEventEntry

apexHwEventEntry 1.3.6.1.4.1.1166.1.31.200.1.1
Hardware Event Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexHwEventEntry  

apexHwEventIndex 1.3.6.1.4.1.1166.1.31.200.1.1.1
Index to HW Event table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7fffffff  

apexHwEventTimeLogged 1.3.6.1.4.1.1166.1.31.200.1.1.2
Time in GPS seconds (apexSystemTime) that this event was logged.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexHwEventAlarmCode 1.3.6.1.4.1.1166.1.31.200.1.1.3
Last number of alarm OID. Can be one of the following: 0 Indicates event is informational and may or may not cause an alarm. 8000 apexAlarmHardwareFault 8002 apexAlarmTemperatureFault 8003 apexAlarmFanFault 8004 apexAlarmPowerFault 8042 apexAlarmQamModuleFault 8043 apexAlarmQamRfPortFault 8044 apexAlarmQamChannelFault 8045 apexAlarmQamRfRedundFailOver 8046 apexAlarmQamRfRedundMismatch 8070 apexAlarmRemCommFault 8071 apexAlarmRemFault More details about the error can be found in apexHwEventDescription.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexHwEventAlarmSeverity 1.3.6.1.4.1.1166.1.31.200.1.1.4
Alarm severity level of this event.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexHwEventData 1.3.6.1.4.1.1166.1.31.200.1.1.5
Additional integer data. When apexHwEventAlarmCode is non-zero, this will be the same as Additional Data 1 as in the trap for the alarm. When apexHwEventAlarmCode is zero, this may contain additional data helpful in debug.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexHwEventDescription 1.3.6.1.4.1.1166.1.31.200.1.1.6
Text description of the event.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexInvalidInitDataTable 1.3.6.1.4.1.1166.1.31.200.2
Table of Invalid Initialization Data Errors. Maximum of 100 errors will be recorded.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexInvalidInitDataEntry

apexInvalidInitDataEntry 1.3.6.1.4.1.1166.1.31.200.2.1
Invalid Initialization Data Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexInvalidInitDataEntry  

apexInvalidInitDataIndex 1.3.6.1.4.1.1166.1.31.200.2.1.1
Index to Invalid Initialization Data table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7fffffff  

apexInvalidInitDataTimeLogged 1.3.6.1.4.1.1166.1.31.200.2.1.2
Time in GPS seconds (apexSystemTime) that this event was logged.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexInvalidInitDataDescription 1.3.6.1.4.1.1166.1.31.200.2.1.3
Text string describing the data error.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexOutputTsEventTable 1.3.6.1.4.1.1166.1.31.200.3
Table of Output Stream events that have occurred. Maximum of 200 events will be recorded.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexOutputTsEventEntry

apexOutputTsEventEntry 1.3.6.1.4.1.1166.1.31.200.3.1
Output Stream Error Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexOutputTsEventEntry  

apexOutputTsEventIndex 1.3.6.1.4.1.1166.1.31.200.3.1.1
Index to Output Stream Error table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7fffffff  

apexOutputTsEventTimeLogged 1.3.6.1.4.1.1166.1.31.200.3.1.2
Time in GPS seconds (apexSystemTime) that this event was logged.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsEventAlarmCode 1.3.6.1.4.1.1166.1.31.200.3.1.3
Last number of alarm OID. Can be one of the following: 0 Indicates event is informational and may or may not cause an alarm. 8040 apexAlarmOutputUtilizationFault 8041 apexAlarmOutputOverflow More details about the error can be found in apexOutputTsEventDescription.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsEventAlarmSeverity 1.3.6.1.4.1.1166.1.31.200.3.1.4
Alarm severity level of this event.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexOutputTsEventOutputTsNum 1.3.6.1.4.1.1166.1.31.200.3.1.5
The number of the output transport stream for this event.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..48  

apexOutputTsEventCurRate 1.3.6.1.4.1.1166.1.31.200.3.1.6
Value of apexOutputTsUtilizCurRate when event occurred.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsEventAvgRate 1.3.6.1.4.1.1166.1.31.200.3.1.7
Value of apexOutputTsUtilizAvgRate when event occurred.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsEventMinRate 1.3.6.1.4.1.1166.1.31.200.3.1.8
Value of apexOutputTsUtilizMinRate when event occurred.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsEventPeakRate 1.3.6.1.4.1.1166.1.31.200.3.1.9
Value of apexOutputTsUtilizPeakRate when event occurred.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsEventCurDropPackets 1.3.6.1.4.1.1166.1.31.200.3.1.10
Value of apexOutputTsUtilizCurDropPackets when event occurred.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsEventPeakDropPackets 1.3.6.1.4.1.1166.1.31.200.3.1.11
Value of apexOutputTsUtilizPeakDropPackets when event occurred.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsEventRollingDropPackets 1.3.6.1.4.1.1166.1.31.200.3.1.12
Value of apexOutputTsUtilizRollingDropPackets when event occurred.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsEventTotalDropPackets 1.3.6.1.4.1.1166.1.31.200.3.1.13
Value of apexOutputTsUtilizTotalDropPackets when event occurred.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexOutputTsEventDescription 1.3.6.1.4.1.1166.1.31.200.3.1.14
Text description of the event. Maximum length is 128 characters.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexGbeInputTsEventTable 1.3.6.1.4.1.1166.1.31.200.4
Table of Gigabit Ethernet Input Transport Stream Events that have occurred. Maximum of 100 events will be recorded.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexGbeInputTsEventEntry

apexGbeInputTsEventEntry 1.3.6.1.4.1.1166.1.31.200.4.1
Gigabit Ethernet Input Transport Stream Event Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexGbeInputTsEventEntry  

apexGbeInputTsEventIndex 1.3.6.1.4.1.1166.1.31.200.4.1.1
Index to Gigabit Ethernet Input Transport Stream Event table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7fffffff  

apexGbeInputTsEventTimeLogged 1.3.6.1.4.1.1166.1.31.200.4.1.2
Time in GPS seconds (apexSystemTime) that this event was logged.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeInputTsEventAlarmCode 1.3.6.1.4.1.1166.1.31.200.4.1.3
Last number of alarm OID. Can be one of the following: 0 Indicates event is informational and may or may not cause an alarm. 8022 apexAlarmGbeInputStreamLowBitRate 8023 apexAlarmGbeInputStreamHighBitRate 8024 apexAlarmGbeMptsRedundPrimaryThreshold 8025 apexAlarmGbeMptsRedundFailOver More details about the error may be found in apexGbeInputTsEventDescription.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeInputTsEventAlarmSeverity 1.3.6.1.4.1.1166.1.31.200.4.1.4
Alarm severity level of this event.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), indeterminate(2), warning(3), minor(4), major(5), critical(6)  

apexGbeInputTsEventRedundantConfig 1.3.6.1.4.1.1166.1.31.200.4.1.5
Indicates whether this input transport stream was configured as a primary or secondary at the time of the event.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), primary(1), secondary(2)  

apexGbeInputTsEventGbeInterface 1.3.6.1.4.1.1166.1.31.200.4.1.6
Value of apexInputTsStatPriInputInterface or apexInputTsStatSecInputInterface at the time of the event.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeInputTsEventUdpPort 1.3.6.1.4.1.1166.1.31.200.4.1.7
Value of apexInputTsStatPriInputUdp or apexInputTsStatSecInputUdp at the time of the event.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeInputTsEventMulticastIp 1.3.6.1.4.1.1166.1.31.200.4.1.8
Value of apexInputTsStatPriInputMulticastIp or apexInputTsStatSecInputMulticastIp at the time of the event.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexGbeInputTsEventSourceIp 1.3.6.1.4.1.1166.1.31.200.4.1.9
Value of apexInputTsStatPriInputSourceIp or apexInputTsStatSecInputSourceIp at the time of the event.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexGbeInputTsEventInputTsState 1.3.6.1.4.1.1166.1.31.200.4.1.10
Value of apexInputTsStatPriState or apexInputTsStatSecState at the time of the event. For threshold or fail over events, the state reported is always the Primary input stream state.
Status: current Access: read-only
OBJECT-TYPE    
  InputTsStateTYPE  

apexGbeInputTsEventRateCompareType 1.3.6.1.4.1.1166.1.31.200.4.1.11
Comparison type at time of event (stream or data).
Status: current Access: read-only
OBJECT-TYPE    
  RateComparisonTYPE  

apexGbeInputTsEventSamplingPeriod 1.3.6.1.4.1.1166.1.31.200.4.1.12
Sample period in seconds of the stream and data counts reported. Using the sample period and the stream or data counts, the actual input rate at the time of the event can be computed.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexGbeInputTsEventPriCurStreamCount 1.3.6.1.4.1.1166.1.31.200.4.1.13
Current Primary input stream Packet Count at the time of the event. This is the number of packets received, including Nulls, during the sample period defined in apexGbeInputTsEventSamplingPeriod.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeInputTsEventPriCurDataCount 1.3.6.1.4.1.1166.1.31.200.4.1.14
Current Primary input data Packet Count at the time of the event. This is the number of data packets received (non-Nulls), during the sample period defined in apexGbeInputTsEventSamplingPeriod.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeInputTsEventSecCurStreamCount 1.3.6.1.4.1.1166.1.31.200.4.1.15
Current Secondary input stream Packet Count at the time of the event. This is the number of packets received, including Nulls, during the sample period defined in apexGbeInputTsEventSamplingPeriod.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeInputTsEventSecCurDataCount 1.3.6.1.4.1.1166.1.31.200.4.1.16
Current Secondary input data Packet Count at the time of the event. This is the number of data packets received (non-Nulls), during the sample period defined in apexGbeInputTsEventSamplingPeriod.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

apexGbeInputTsEventDescription 1.3.6.1.4.1.1166.1.31.200.4.1.17
Text description of the event. Maximum length is 128 characters.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexRtspEventTable 1.3.6.1.4.1.1166.1.31.200.5
Table of RTSP Events that have occurred. Maximum of 100 events will be recorded.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexRtspEventEntry

apexRtspEventEntry 1.3.6.1.4.1.1166.1.31.200.5.1
RTSP Event Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexRtspEventEntry  

apexRtspEventIndex 1.3.6.1.4.1.1166.1.31.200.5.1.1
Index to RTSP Event table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7fffffff  

apexRtspEventTimeLogged 1.3.6.1.4.1.1166.1.31.200.5.1.2
Time in GPS seconds (apexSystemTime) that this event was logged.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRtspEventControllerIp 1.3.6.1.4.1.1166.1.31.200.5.1.3
IP address of the RTSP Controller associated with this event. Value will be zero if the event is not associated with a specific controller. Refer to apexRtspEventSourceDescription for the source of the event.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexRtspEventSessionCount 1.3.6.1.4.1.1166.1.31.200.5.1.4
Number of active sessions for the RTSP Controller associated with this event. Value will be total count of all sessions for all controllers if the event is not associated with a specific controller. Refer to apexRtspEventSourceDescription for the source of the event.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexRtspEventSourceDescription 1.3.6.1.4.1.1166.1.31.200.5.1.5
Text description of the source of the event. May indicate a controller identifier or an APEX application process.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexRtspEventDescription 1.3.6.1.4.1.1166.1.31.200.5.1.6
Text description of the event.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

apexMappingErrorTable 1.3.6.1.4.1.1166.1.31.200.6
Table of program, ancillary PID, and stream pass through mapping errors that have occurred. Maximum of 100 error events will be recorded.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexMappingErrorEntry

apexMappingErrorEntry 1.3.6.1.4.1.1166.1.31.200.6.1
Program, PID, Stream Pass Through Error Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexMappingErrorEntry  

apexMappingErrorIndex 1.3.6.1.4.1.1166.1.31.200.6.1.1
Index to Program, PID, Stream Pass Through, DEPI Control, DEPI Session Error table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7fffffff  

apexMappingErrorTimeLogged 1.3.6.1.4.1.1166.1.31.200.6.1.2
Time in GPS seconds (apexSystemTime) that this error was logged.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMappingErrorCode 1.3.6.1.4.1.1166.1.31.200.6.1.3
Error code for this mapping error. 0 indicates no error.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMappingErrorMappingType 1.3.6.1.4.1.1166.1.31.200.6.1.4
Type of mapping (program, ancillary PID, or stream pass through).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), program(1), ancillaryPid(2), streamPassthru(3), depiControl(4), depiSession(5)  

apexMappingErrorInputType 1.3.6.1.4.1.1166.1.31.200.6.1.5
Input Type. Indicates if mapping is from Gigabit Ethernet or Fast Ethernet.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), gbe(1), fastEnet(2)  

apexMappingErrorInputInterface 1.3.6.1.4.1.1166.1.31.200.6.1.6
Interface port number of the primary input interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMappingErrorUdpPort 1.3.6.1.4.1.1166.1.31.200.6.1.7
Input UDP Port for primary input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMappingErrorMulticastIp 1.3.6.1.4.1.1166.1.31.200.6.1.8
The Multicast receive IP address for primary input.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexMappingErrorSourceIp 1.3.6.1.4.1.1166.1.31.200.6.1.9
This is the IGMP v3 Source IP address of the source device for the primary input.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexMappingErrorInputProgramPid 1.3.6.1.4.1.1166.1.31.200.6.1.10
For program mappings, this is the input program number of the program being mapped. For ancillary PID mappings, this is the input PID number being mapped. For stream pass through mappings, this field is not used and is set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMappingErrorOutputProgramPid 1.3.6.1.4.1.1166.1.31.200.6.1.11
For program mappings, this is the output program number of the program being mapped. For ancillary PID mappings, this is the output PID number being mapped. For stream pass through mappings, this field is not used and is set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMappingErrorOutputOpMode 1.3.6.1.4.1.1166.1.31.200.6.1.12
Operating mode of the output transport stream for this mapping.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notInUse(0), sessionControl(1), manualRouting(2)  

apexMappingErrorOutputTsNum 1.3.6.1.4.1.1166.1.31.200.6.1.13
The number of the output transport stream for this mapping error.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..48  

apexMappingErrorSecInputInterface 1.3.6.1.4.1.1166.1.31.200.6.1.14
Interface port number of the secondary input interface. An interface number of 0 indicates no secondary input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMappingErrorSecUdpPort 1.3.6.1.4.1.1166.1.31.200.6.1.15
Input UDP Port for secondary input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexMappingErrorSecMulticastIp 1.3.6.1.4.1.1166.1.31.200.6.1.16
The Multicast receive IP address for secondary input.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexMappingErrorSecSourceIp 1.3.6.1.4.1.1166.1.31.200.6.1.17
This is the IGMP v3 Source IP address of the source device for the secondary input.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

apexChassisRedundancyEventTable 1.3.6.1.4.1.1166.1.31.200.7
Table of Chassis Redundancy Events. Maximum of 300 events will be recorded.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApexChassisRedundancyEventEntry

apexChassisRedundancyEventEntry 1.3.6.1.4.1.1166.1.31.200.7.1
Chassis Redundancy Event Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ApexChassisRedundancyEventEntry  

apexChassisRedundancyEventIndex 1.3.6.1.4.1.1166.1.31.200.7.1.1
Index for Chassis Redundancy Event table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7fffffff  

apexChassisRedundancyEventTimeLogged 1.3.6.1.4.1.1166.1.31.200.7.1.2
Time in GPS seconds (apexSystemTime) that this event was logged.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

apexChassisRedundancyEventDescription 1.3.6.1.4.1.1166.1.31.200.7.1.3
Text string describing the event.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

trapConfigurationChangeInteger 1.3.6.1.4.1.1166.1.31.0.3
This trap is issued if configuration of a single variable with integer type was changed (via ANY interface). TrapChangedValueInteger variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate'
Status: current Access: read-only
NOTIFICATION-TYPE    

trapConfigurationChangeDisplayString 1.3.6.1.4.1.1166.1.31.0.4
This trap is issued if configuration of a single variable with DisplayString type was changed (via ANY interface). TrapChangedValueDisplayString variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate'
Status: current Access: read-only
NOTIFICATION-TYPE    

trapConfigurationChangeOID 1.3.6.1.4.1.1166.1.31.0.5
This trap is issued if configuration of a single variable with OID type was changed (via ANY interface). TrapChangedValueOID variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate'
Status: current Access: read-only
NOTIFICATION-TYPE    

trapConfigurationChangeIpAddress 1.3.6.1.4.1.1166.1.31.0.6
This trap is issued if configuration of a single variable with IpAddress type was changed (via ANY interface). TrapChangedValueIpAddress variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate'
Status: current Access: read-only
NOTIFICATION-TYPE    

trapConditionNotInList 1.3.6.1.4.1.1166.1.31.0.20
This trap is issued if a condition is being cleared and it is not in the condition list. trapAdditionalInfoInteger1 : Task and Function ID (task and function generates the error condition) trapAdditionalInfoInteger2 : Condition number trapAdditionalInfoInteger3 : Condition severity
Status: current Access: read-only
NOTIFICATION-TYPE    

trapConditionAlreadyInList 1.3.6.1.4.1.1166.1.31.0.21
This trap is issued if a condition is being set and it is already in the condition list. trapAdditionalInfoInteger1 : Task and Function ID (task and function generates the error condition) trapAdditionalInfoInteger2 : Condition number trapAdditionalInfoInteger3 : Condition severity
Status: current Access: read-only
NOTIFICATION-TYPE    

trapConditionListFull 1.3.6.1.4.1.1166.1.31.0.22
This trap is issued if a condition is being set and the condition list is full. trapAdditionalInfoInteger1 : Task and Function ID (task and function generates the error condition) trapAdditionalInfoInteger2 : Condition number trapAdditionalInfoInteger3 : Condition severity
Status: current Access: read-only
NOTIFICATION-TYPE    

trapInvalidCaseInSwitch 1.3.6.1.4.1.1166.1.31.0.23
This trap is issued when in a switch statement the default case is reached. The trapAdditionalInfoInteger1 will contain the task and Function ID. The trapAdditionalInfoInteger2 will contain value of the switch. The trapAdditionalInfoInteger3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapCannotCreateSemaphore 1.3.6.1.4.1.1166.1.31.0.24
This trap is issued when a semaphore cannot be created. The trapAdditionalInfoInteger1 will contain the task and Function ID, the trapAdditionalInfoInteger2 and trapAdditionalInfoInteger3 will not be used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapCannotOpenSocket 1.3.6.1.4.1.1166.1.31.0.25
This trap is issued when a socket cannot be opened. The trapAdditionalInfoInteger1 will contain the task and Function ID. The trapAdditionalInfoInteger2 will contain the errno returned by the call to socket(). The trapAdditionalInfoInteger3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapUnknownMessageReceived 1.3.6.1.4.1.1166.1.31.0.26
This trap is issued when an unknown message is received. The trapAdditionalInfoInteger1 will contain the task and Function ID. The trapAdditionalInfoInteger2 will contain the message ID and the trapAdditionalInfoInteger3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapInvalidMessageReceived 1.3.6.1.4.1.1166.1.31.0.27
This trap is issued when an invalid message is received. The trapAdditionalInfoInteger1 will contain the task and Function ID. The trapAdditionalInfoInteger2 will contain the message ID and the trapAdditionalInfoInteger3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapHardwareFault 1.3.6.1.4.1.1166.1.31.0.8000
See corresponding alarm apexAlarmHardwareFault. Additional Info 1 carries HW Error Code (refer to HW Event Log for details). Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapInvalidInitData 1.3.6.1.4.1.1166.1.31.0.8001
See corresponding alarm apexAlarmInvalidInitData. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapTemperatureFault 1.3.6.1.4.1.1166.1.31.0.8002
See corresponding alarm apexAlarmTemperatureFault. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapFanFault 1.3.6.1.4.1.1166.1.31.0.8003
See corresponding alarm apexAlarmFanFault. This trap is sent on summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapPowerFault 1.3.6.1.4.1.1166.1.31.0.8004
See corresponding alarm apexAlarmPowerFault. Additional Info 1 carries the apexPsStatusTable index (1 to 2). Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapGbeLossOfPhysicalInput 1.3.6.1.4.1.1166.1.31.0.8020
See corresponding alarm apexAlarmGbeLossOfPhysicalInput. Additional Info 1 carries the Gigabit Ethernet Interface Number (1 to 4). Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapGbeBufferFullness 1.3.6.1.4.1.1166.1.31.0.8021
See corresponding alarm apexAlarmGbeBufferFullness. Additional Info 1 carries the Gigabit Ethernet Processor Number (1 to 2). Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapGbeInputStreamLowBitRate 1.3.6.1.4.1.1166.1.31.0.8022
See corresponding alarm apexAlarmGbeInputStreamLowBitRate. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapGbeInputStreamHighBitRate 1.3.6.1.4.1.1166.1.31.0.8023
See corresponding alarm apexAlarmGbeInputStreamHighBitRate. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapGbeMptsRedundPrimaryThreshold 1.3.6.1.4.1.1166.1.31.0.8024
See corresponding alarm apexAlarmGbeMptsRedundPrimaryThreshold. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapGbeMptsRedundFailOver 1.3.6.1.4.1.1166.1.31.0.8025
See corresponding alarm apexAlarmGbeMptsRedundFailOver. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapServiceInError 1.3.6.1.4.1.1166.1.31.0.8026
See corresponding alarm apexAlarmServiceInError. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapGbeLossOfInputStream 1.3.6.1.4.1.1166.1.31.0.8027
See corresponding alarm apexAlarmGbeLossOfInputStream. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapGigeToHostCommFault 1.3.6.1.4.1.1166.1.31.0.8028
See corresponding alarm apexAlarmGigeToHostCommFault. This trap is sent on a summary basis. Additional Info 1 is not used. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapGbeInterfaceRedundFailOver 1.3.6.1.4.1.1166.1.31.0.8029
See corresponding alarm apexAlarmGbeInterfaceRedundFailOver. This trap is sent on a GbE Redundant Pair basis. Additional Info 1 contains the GbE interface number that lost link. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapOutputUtilizationFault 1.3.6.1.4.1.1166.1.31.0.8040
See corresponding alarm apexAlarmOutputUtilizationFault. This trap is sent on an Output Transport Stream basis. Additional Info 1 carries the Output Transport Stream number (1 to 48). Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapOutputOverflow 1.3.6.1.4.1.1166.1.31.0.8041
See corresponding alarm apexAlarmOutputOverflow. This trap is sent on an Output Transport Stream basis. Additional Info 1 carries the Output Transport Stream number (1 to 48). Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapQamModuleFault 1.3.6.1.4.1.1166.1.31.0.8042
See corresponding alarm apexAlarmQamModuleFault. This trap is sent on a QAM Module basis. Additional Info 1 carries the QAM Module number (1 to 3). Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapQamRfPortFault 1.3.6.1.4.1.1166.1.31.0.8043
See corresponding alarm apexAlarmQamRfPortFault. This trap is sent on a QAM RF Port basis. Additional Info 1 carries the QAM RF Port number: RF Port 1 = QAM Module 1, RF 1 RF Port 2 = QAM Module 1, RF 2 RF Port 3 = QAM Module 2, RF 1 RF Port 4 = QAM Module 2, RF 2 RF Port 5 = QAM Module 3, RF 1 RF Port 6 = QAM Module 3, RF 2 Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapQamChannelFault 1.3.6.1.4.1.1166.1.31.0.8044
See corresponding alarm apexAlarmQamChannelFault. This trap is sent on a QAM Channel basis. Additional Info 1 carries the QAM Channel number. 1 to 8 = QAM Module 1, RF 1, QAM Channel A to H 9 to 16 = QAM Module 1, RF 2, QAM Channel A to H 17 to 24 = QAM Module 2, RF 1, QAM Channel A to H 25 to 32 = QAM Module 2, RF 2, QAM Channel A to H 33 to 40 = QAM Module 3, RF 1, QAM Channel A to H 41 to 48 = QAM Module 3, RF 2, QAM Channel A to H Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapQamRfRedundFailOver 1.3.6.1.4.1.1166.1.31.0.8045
See corresponding alarm apexAlarmQamRfRedundFailOver. This trap is sent on a Primary QAM RF Port basis. Additional Info 1 carries the Primary QAM RF Port number. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapQamRfRedundMismatch 1.3.6.1.4.1.1166.1.31.0.8046
See corresponding alarm apexAlarmQamRfRedundMismatch. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapRtspControllerCommFault 1.3.6.1.4.1.1166.1.31.0.8050
See corresponding alarm apexAlarmRtspControllerCommFault. This trap is sent on a controller basis. Additional Info 1 carries the controller number. Additional Info 2 is not used. Additional Info 3 is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapRdsCommFault 1.3.6.1.4.1.1166.1.31.0.8060
See corresponding alarm apexAlarmRdsCommFault. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapRemCommFault 1.3.6.1.4.1.1166.1.31.0.8070
See corresponding alarm apexAlarmRemCommFault. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapRemFault 1.3.6.1.4.1.1166.1.31.0.8071
See corresponding alarm apexAlarmRemFault. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapDepiControlConnectionFault 1.3.6.1.4.1.1166.1.31.0.8080
See corresponding alarm apexAlarmDepiControlConnectionFault. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapDepiSessionSetupFault 1.3.6.1.4.1.1166.1.31.0.8081
See corresponding alarm apexAlarmDepiSessionSetupFault. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapDtiSyncLossFault 1.3.6.1.4.1.1166.1.31.0.8082
See corresponding alarm apexAlarmDtiSyncLossFault. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapChassisRedundancyPrimaryFailover 1.3.6.1.4.1.1166.1.31.0.8090
See corresponding alarm apexAlarmChassisRedundancyPrimaryFailover. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapChassisRedundancySecondaryFailover 1.3.6.1.4.1.1166.1.31.0.8091
See corresponding alarm apexAlarmChassisRedundancySecondaryFailover. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapChassisRedundancyAvailabilityFault 1.3.6.1.4.1.1166.1.31.0.8092
See corresponding alarm apexAlarmChassisRedundancyAvailabilityFault. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapChassisRedundancyLinkFault 1.3.6.1.4.1.1166.1.31.0.8093
See corresponding alarm apexAlarmChassisRedundancyLinkFault. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapChassisRedundancyConfigurationFault 1.3.6.1.4.1.1166.1.31.0.8094
See corresponding alarm apexAlarmChassisRedundancyConfigurationFault. This trap is sent on a summary basis. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapEmUserLoginFailed 1.3.6.1.4.1.1166.1.31.0.8100
See corresponding event apexEventEmUserLoginFailed. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapQamModuleUpgraded 1.3.6.1.4.1.1166.1.31.0.8101
See corresponding event apexEventQamModuleUpgraded. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapChassisRedundancyPrimaryForceFailover 1.3.6.1.4.1.1166.1.31.0.8110
See corresponding event apexEventChassisRedunPrimaryForceFailover. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapChassisRedundancySecondaryForceFailover 1.3.6.1.4.1.1166.1.31.0.8111
See corresponding event apexEventChassisRedunSecondaryForceFailover. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapChassisRedundancyFirmwareVersionMismatch 1.3.6.1.4.1.1166.1.31.0.8112
See corresponding event apexEventChassisRedunFirmwareVersionMismatch. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE    

trapChassisRedundancyQAMVersionMismatch 1.3.6.1.4.1.1166.1.31.0.8113
See corresponding event apexEventChassisRedunQAMVersionMismatch. Additional Info is not used.
Status: current Access: read-only
NOTIFICATION-TYPE