ASCEND-MIBANSWER-MIB

File: ASCEND-MIBANSWER-MIB.mib (31512 bytes)

Imported modules

ASCEND-MIB RFC1155-SMI RFC-1212

Imported symbols

configuration IpAddress OBJECT-TYPE

Defined Types

DisplayString  
OCTET STRING    

MibanswerProfileEntry  
SEQUENCE    
  answerProfile-Index-o INTEGER
  answerProfile-UseAnswerForAllDefaults INTEGER
  answerProfile-Force56kbps INTEGER
  answerProfile-ProfilesRequired INTEGER
  answerProfile-ClidAuthMode INTEGER
  answerProfile-ClidSelection INTEGER
  answerProfile-CallbackClidPrefix DisplayString
  answerProfile-PppAnswer-Enabled INTEGER
  answerProfile-PppAnswer-ReceiveAuthMode INTEGER
  answerProfile-PppAnswer-BiDirectionalAuth INTEGER
  answerProfile-PppAnswer-SubstituteSendName DisplayString
  answerProfile-PppAnswer-DisconnectOnAuthTimeout INTEGER
  answerProfile-PppAnswer-BridgingGroup INTEGER
  answerProfile-PppAnswer-LinkCompression INTEGER
  answerProfile-PppAnswer-Mru INTEGER
  answerProfile-PppAnswer-Lqm INTEGER
  answerProfile-PppAnswer-LqmMinimumPeriod INTEGER
  answerProfile-PppAnswer-LqmMaximumPeriod INTEGER
  answerProfile-PppAnswer-CbcpEnabled INTEGER
  answerProfile-PppAnswer-IpxHeaderCompression INTEGER
  answerProfile-PppAnswer-Mtu INTEGER
  answerProfile-PppAnswer-AuthForAsyncFramedUsers INTEGER
  answerProfile-PppAnswer-MaxPapAuthRetry INTEGER
  answerProfile-PppAnswer-MaxPppConfigureRetry INTEGER
  answerProfile-PppAnswer-PppRestartTimer INTEGER
  answerProfile-PppAnswer-MaxPppRestartTimer INTEGER
  answerProfile-MpAnswer-Enabled INTEGER
  answerProfile-MpAnswer-MinimumChannels INTEGER
  answerProfile-MpAnswer-MaximumChannels INTEGER
  answerProfile-MpAnswer-BacpEnable INTEGER
  answerProfile-MppAnswer-Enabled INTEGER
  answerProfile-MppAnswer-DynamicAlgorithm INTEGER
  answerProfile-MppAnswer-BandwidthMonitorDirection INTEGER
  answerProfile-MppAnswer-IncrementChannelCount INTEGER
  answerProfile-MppAnswer-DecrementChannelCount INTEGER
  answerProfile-MppAnswer-SecondsHistory INTEGER
  answerProfile-MppAnswer-AddPersistence INTEGER
  answerProfile-MppAnswer-SubPersistence INTEGER
  answerProfile-MppAnswer-TargetUtilization INTEGER
  answerProfile-FrAnswer-Enabled INTEGER
  answerProfile-TcpClearAnswer-Enabled INTEGER
  answerProfile-AraAnswer-Enabled INTEGER
  answerProfile-V120Answer-Enabled INTEGER
  answerProfile-V120Answer-FrameLength INTEGER
  answerProfile-X25Answer-Enabled INTEGER
  answerProfile-X25Answer-X25Profile DisplayString
  answerProfile-X25Answer-X3Profile INTEGER
  answerProfile-X25Answer-MaxCalls INTEGER
  answerProfile-X25Answer-VcTimerEnable INTEGER
  answerProfile-X25Answer-AutoCallX121Address DisplayString
  answerProfile-X25Answer-ReverseCharge INTEGER
  answerProfile-X25Answer-X3CustomProf DisplayString
  answerProfile-EuAnswer-EurawEnabled INTEGER
  answerProfile-EuAnswer-EuuiEnabled INTEGER
  answerProfile-EuAnswer-DceAddr INTEGER
  answerProfile-EuAnswer-DteAddr INTEGER
  answerProfile-EuAnswer-Mru INTEGER
  answerProfile-IpAnswer-Enabled INTEGER
  answerProfile-IpAnswer-VjHeaderPrediction INTEGER
  answerProfile-IpAnswer-AssignAddress INTEGER
  answerProfile-IpAnswer-RoutingMetric INTEGER
  answerProfile-IpAnswer-PrivateRouteProfileRequired INTEGER
  answerProfile-IpAnswer-PoolForAsyncFramedUser INTEGER
  answerProfile-IpxAnswer-Enabled INTEGER
  answerProfile-IpxAnswer-PeerMode INTEGER
  answerProfile-SessionInfo-CallFilter DisplayString
  answerProfile-SessionInfo-DataFilter DisplayString
  answerProfile-SessionInfo-FilterPersistence INTEGER
  answerProfile-SessionInfo-FilterRequired INTEGER
  answerProfile-SessionInfo-IdleTimer INTEGER
  answerProfile-SessionInfo-TsIdleMode INTEGER
  answerProfile-SessionInfo-TsIdleTimer INTEGER
  answerProfile-SessionInfo-MaxCallDuration INTEGER
  answerProfile-X75Answer-Enabled INTEGER
  answerProfile-X75Answer-KFramesOutstanding INTEGER
  answerProfile-X75Answer-N2Retransmissions INTEGER
  answerProfile-X75Answer-T1RetranTimer INTEGER
  answerProfile-X75Answer-FrameLength INTEGER
  answerProfile-FramedOnly INTEGER
  answerProfile-HdlcNrmAnswer-Enabled INTEGER
  answerProfile-Visa2Answer-Enabled INTEGER
  answerProfile-AtmAnswer-SvcEnabled INTEGER
  answerProfile-PriorityAnswer-Enabled INTEGER
  answerProfile-PriorityAnswer-PacketClassification INTEGER
  answerProfile-PriorityAnswer-MaxRtpPacketDelay INTEGER
  answerProfile-PriorityAnswer-MinimumRtpPort INTEGER
  answerProfile-PriorityAnswer-MaximumRtpPort INTEGER
  answerProfile-PriorityAnswer-NoHighPrioPktDuration INTEGER
  answerProfile-Action-o INTEGER

Defined Values

mibanswerProfile 1.3.6.1.4.1.529.23.3
OBJECT IDENTIFIER    

mibanswerProfileTable 1.3.6.1.4.1.529.23.3.1
A list of mibanswerProfile profile entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MibanswerProfileEntry

mibanswerProfileEntry 1.3.6.1.4.1.529.23.3.1.1
A mibanswerProfile entry containing objects that maps to the parameters of mibanswerProfile profile.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MibanswerProfileEntry  

answerProfile-Index-o 1.3.6.1.4.1.529.23.3.1.1.1
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

answerProfile-UseAnswerForAllDefaults 1.3.6.1.4.1.529.23.3.1.1.2
When set to Yes, this profile will provide the default values for fields when building profiles. When set to No the factory profile will be used instead.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-Force56kbps 1.3.6.1.4.1.529.23.3.1.1.3
If yes then inbound 64 kbps calls are connected at 56 kbps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-ProfilesRequired 1.3.6.1.4.1.529.23.3.1.1.4
Unused when incoming authentication is used. When authentication is not used a No value in this field indicates that we will create a temporary profile for a user on incoming calls. A Yes value indicates that we must find an existing profile (by matching the caller's IP address). This provided NO security.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-ClidAuthMode 1.3.6.1.4.1.529.23.3.1.1.5
Specifies how calling line identification (CLID) will be used for incoming call authentication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ignore(1), clidRequire(3), clidPrefer(2), clidFirst(7), clidFallback(4), dnisRequire(5), dnisPref(6), dnisFirst(8), dnisFallback(9)  

answerProfile-ClidSelection 1.3.6.1.4.1.529.23.3.1.1.73
Selection of the CLID. An incoming call can optionally specify several CLIDs. A CLID provided by the PSTN (network provided) is considered secure. A CLID provided by the end user (user provided) is secure only if it has been validated by the PSTN (user provided, network verified and passed). Other forms of user CLIDs are considered unsecure.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER first(1), securePrefer(2), secureRequire(3), userPrefer(4), userRequire(5)  

answerProfile-CallbackClidPrefix 1.3.6.1.4.1.529.23.3.1.1.85
Prefix to prepend to the dial number when callback is performed with the CLID number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

answerProfile-PppAnswer-Enabled 1.3.6.1.4.1.529.23.3.1.1.6
Set to Yes to enable incoming PPP calls. This includes the PPP variants, MP and MPP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-PppAnswer-ReceiveAuthMode 1.3.6.1.4.1.529.23.3.1.1.7
The type of PPP authentication to use for incoming calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noPppAuth(1), papPppAuth(2), chapPppAuth(3), anyPppAuth(4), desPapPppAuth(5), tokenPapPppAuth(6), tokenChapPppAuth(7), cacheTokenPppAuth(8), msChapPppAuth(9), papPreferred(10)  

answerProfile-PppAnswer-BiDirectionalAuth 1.3.6.1.4.1.529.23.3.1.1.79
This parameter enables the authentication to be done in both directions. It can be used only with the CHAP, MS-CHAP or CACHE-TOKEN authentication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), allowed(2), required(3)  

answerProfile-PppAnswer-SubstituteSendName 1.3.6.1.4.1.529.23.3.1.1.80
Name send to the far end, if different from the global system name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

answerProfile-PppAnswer-DisconnectOnAuthTimeout 1.3.6.1.4.1.529.23.3.1.1.8
???.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-PppAnswer-BridgingGroup 1.3.6.1.4.1.529.23.3.1.1.9
The default bridging group. Interfaces with the same bridging group can bridge to each other. Set to 0 to disable bridging.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PppAnswer-LinkCompression 1.3.6.1.4.1.529.23.3.1.1.10
The default type of link compression to use for PPP, MP, and MPP calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), stac(2), stac9(3), msStac(4), mppc(5)  

answerProfile-PppAnswer-Mru 1.3.6.1.4.1.529.23.3.1.1.11
The Maximum Receive Unit, i.e. the largest frame we will accept.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PppAnswer-Lqm 1.3.6.1.4.1.529.23.3.1.1.12
Link Quality Monitoring. Set to Yes to enable the PPP LQM protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-PppAnswer-LqmMinimumPeriod 1.3.6.1.4.1.529.23.3.1.1.13
The minimum period, in 1/100 of a second, that we will accept/send link quality monitoring packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PppAnswer-LqmMaximumPeriod 1.3.6.1.4.1.529.23.3.1.1.14
The maximum period, in 1/100 of a second, that we will accept/send link quality monitoring packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PppAnswer-CbcpEnabled 1.3.6.1.4.1.529.23.3.1.1.70
Enable Microsoft Callback Control Protocol Negotiation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-PppAnswer-IpxHeaderCompression 1.3.6.1.4.1.529.23.3.1.1.74
Use IPX header compression if encapsulation supports it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-PppAnswer-Mtu 1.3.6.1.4.1.529.23.3.1.1.75
The Maximum Transmit Unit, i.e. the largest frame we will send out.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PppAnswer-AuthForAsyncFramedUsers 1.3.6.1.4.1.529.23.3.1.1.81
Determines whether we need to authenticate async framed users.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notRequired(1), required(2)  

answerProfile-PppAnswer-MaxPapAuthRetry 1.3.6.1.4.1.529.23.3.1.1.82
Number of retries allowed, if PAP authentication fails.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PppAnswer-MaxPppConfigureRetry 1.3.6.1.4.1.529.23.3.1.1.92
Number of retries allowed, if LCP/NCP fails
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PppAnswer-PppRestartTimer 1.3.6.1.4.1.529.23.3.1.1.93
Initial LCP/NCP restart timer
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PppAnswer-MaxPppRestartTimer 1.3.6.1.4.1.529.23.3.1.1.94
Maximum LCP/NCP restart timer
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-MpAnswer-Enabled 1.3.6.1.4.1.529.23.3.1.1.15
Set to Yes to enable incoming MP calls. This includes the MP variant, MPP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-MpAnswer-MinimumChannels 1.3.6.1.4.1.529.23.3.1.1.16
The default value for the minimum number of channels in a multi-channel call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-MpAnswer-MaximumChannels 1.3.6.1.4.1.529.23.3.1.1.17
The default value for the maximum number of channels in a multi-channel call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-MpAnswer-BacpEnable 1.3.6.1.4.1.529.23.3.1.1.18
Enable Bandwidth Allocation Control Protocol (BACP).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-MppAnswer-Enabled 1.3.6.1.4.1.529.23.3.1.1.19
Set to Yes to enable incoming MPP calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-MppAnswer-DynamicAlgorithm 1.3.6.1.4.1.529.23.3.1.1.20
The algorithm to use to calculate the average link utilization. Bandwidth changes are performed on the average utilization, not current utilization.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER constant(1), linear(2), quadratic(3)  

answerProfile-MppAnswer-BandwidthMonitorDirection 1.3.6.1.4.1.529.23.3.1.1.21
The direction to monitor link utilization. A unit can monitor transmit, transmit and receive, or turn off monitoring entirely.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER transmit(1), transmitRecv(2), none(3)  

answerProfile-MppAnswer-IncrementChannelCount 1.3.6.1.4.1.529.23.3.1.1.22
Number of channels to increment as a block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-MppAnswer-DecrementChannelCount 1.3.6.1.4.1.529.23.3.1.1.23
Number of channels to decrement as a block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-MppAnswer-SecondsHistory 1.3.6.1.4.1.529.23.3.1.1.24
The number of seconds of history that link utilization is averaged over to make bandwidth changes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-MppAnswer-AddPersistence 1.3.6.1.4.1.529.23.3.1.1.25
The number of seconds of that the average line utilization must exceed the target utilization before bandwidth will be added.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-MppAnswer-SubPersistence 1.3.6.1.4.1.529.23.3.1.1.26
The number of seconds of that the average line utilization must fall below the target utilization before bandwidth will be reduced. Bandwidth will not be reduced if the reduced bandwidth would exceed the target utilization.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-MppAnswer-TargetUtilization 1.3.6.1.4.1.529.23.3.1.1.27
The default value for the target utilization. Bandwidth changes occur when the average utilization exceeds or falls below this value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-FrAnswer-Enabled 1.3.6.1.4.1.529.23.3.1.1.28
Set to yes to enable incoming FR calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-TcpClearAnswer-Enabled 1.3.6.1.4.1.529.23.3.1.1.29
If enabled, incoming calls that match a local profile with a call management type of tcp-raw will automatically be connected via a raw TCP pipe to the host named in the local profile. If disabled, logins that match a tcp-raw profile will be rejected.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-AraAnswer-Enabled 1.3.6.1.4.1.529.23.3.1.1.30
Set to yes to enable incoming ARA calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-V120Answer-Enabled 1.3.6.1.4.1.529.23.3.1.1.31
Set to yes to enable incoming V120 calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-V120Answer-FrameLength 1.3.6.1.4.1.529.23.3.1.1.32
The default frame length to use for incoming V.120 connections.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-X25Answer-Enabled 1.3.6.1.4.1.529.23.3.1.1.33
If enabled, incoming calls that match a local profile with a call management type of x25 will be accepted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-X25Answer-X25Profile 1.3.6.1.4.1.529.23.3.1.1.34
Name of the x25 profile that this profile is associated with.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

answerProfile-X25Answer-X3Profile 1.3.6.1.4.1.529.23.3.1.1.35
X.3 profile parameter index
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER crtProfile(1), infonetProfile(2), defaultProfile(3), scenProfile(4), ccSspProfile(5), ccTspProfile(6), hardcopyProfile(7), hdxProfile(8), sharkProfile(9), posProfile(12), nullProfile(10), customProfile(11)  

answerProfile-X25Answer-MaxCalls 1.3.6.1.4.1.529.23.3.1.1.36
Max number of unsuccessful calls
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-X25Answer-VcTimerEnable 1.3.6.1.4.1.529.23.3.1.1.37
PAD VCE enable flag
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-X25Answer-AutoCallX121Address 1.3.6.1.4.1.529.23.3.1.1.38
X.121 address to auto-call upon session startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

answerProfile-X25Answer-ReverseCharge 1.3.6.1.4.1.529.23.3.1.1.39
Reverse charge request
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-X25Answer-X3CustomProf 1.3.6.1.4.1.529.23.3.1.1.40
Custom profile enter a string for a custom X.3 profile if x3Prof says custom.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

answerProfile-EuAnswer-EurawEnabled 1.3.6.1.4.1.529.23.3.1.1.45
Enable/disable the EUNET raw protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-EuAnswer-EuuiEnabled 1.3.6.1.4.1.529.23.3.1.1.46
Enable/disable the EUNET UI protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-EuAnswer-DceAddr 1.3.6.1.4.1.529.23.3.1.1.47
The address of the DCE side of the link when the EUNET UI protocol is used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-EuAnswer-DteAddr 1.3.6.1.4.1.529.23.3.1.1.48
The address of the DTE side of the link when the EUNET UI protocol is used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-EuAnswer-Mru 1.3.6.1.4.1.529.23.3.1.1.49
The Maximum Receive Unit, i.e. the largest frame we will accept when the EUNET UI protocol is used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-IpAnswer-Enabled 1.3.6.1.4.1.529.23.3.1.1.50
Set to yes to enable IP routing on incoming calls using encapsulation protocols that support IP routing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-IpAnswer-VjHeaderPrediction 1.3.6.1.4.1.529.23.3.1.1.51
Set to yes to enable Van Jacobson IP header prediction to be negotiated on incoming calls using encapsulation protocols that support this feature.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-IpAnswer-AssignAddress 1.3.6.1.4.1.529.23.3.1.1.52
Set to yes if this unit is configured with one or more pools of IP addresses that will be used as a source of addresses to assign to incoming callers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-IpAnswer-RoutingMetric 1.3.6.1.4.1.529.23.3.1.1.53
The default metric assigned to routes created for incoming calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-IpAnswer-PrivateRouteProfileRequired 1.3.6.1.4.1.529.23.3.1.1.76
Parameter to decide default action,if private route table not found. If set to yes, the call will be cleared if the private route profile cannot be found. If set to no, the call will be allowed to complete, even if the private route profile cannot be found.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-IpAnswer-PoolForAsyncFramedUser 1.3.6.1.4.1.529.23.3.1.1.83
Pool number to be used for dial-in asynchronous PPP framed users with out authentication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-IpxAnswer-Enabled 1.3.6.1.4.1.529.23.3.1.1.54
Set to Yes to enable incoming IPX calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-IpxAnswer-PeerMode 1.3.6.1.4.1.529.23.3.1.1.55
Enable/disable full routing between peer or use the pool to assign a network number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER routerPeer(1), dialinPeer(2)  

answerProfile-SessionInfo-CallFilter 1.3.6.1.4.1.529.23.3.1.1.56
The name of the filter used to determine if a packet should cause the idle timer to be reset or, when the answer profile is used for connection profile defaults, if a call should be placed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

answerProfile-SessionInfo-DataFilter 1.3.6.1.4.1.529.23.3.1.1.57
The name of the filter used to determine if packets should be forwarded or dropped.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

answerProfile-SessionInfo-FilterPersistence 1.3.6.1.4.1.529.23.3.1.1.58
Determines if filters should persist between calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-SessionInfo-FilterRequired 1.3.6.1.4.1.529.23.3.1.1.77
If No, the call will be allowed to come up even if the specified filter was not found either locally, in the cache or in RADIUS. If Yes, then the call will be cleared if the specified filter was not found either locally, in the cache or in RADIUS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-SessionInfo-IdleTimer 1.3.6.1.4.1.529.23.3.1.1.59
The number of seconds of no activity before a call will be dropped. The value 0 disables the idle timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-SessionInfo-TsIdleMode 1.3.6.1.4.1.529.23.3.1.1.60
The method used to determine when the terminal server idle session timer is reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noIdle(1), inputOnlyIdle(2), inputOutputIdle(3)  

answerProfile-SessionInfo-TsIdleTimer 1.3.6.1.4.1.529.23.3.1.1.61
The number of seconds of no activity as defined by the idle mode before a session will be terminated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-SessionInfo-MaxCallDuration 1.3.6.1.4.1.529.23.3.1.1.62
The number of minutes of connect time before a call will be dropped. The value 0 disables the connection timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-X75Answer-Enabled 1.3.6.1.4.1.529.23.3.1.1.63
Set to yes to enable incoming X75 calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-X75Answer-KFramesOutstanding 1.3.6.1.4.1.529.23.3.1.1.64
Number of frames outstanding before we require an ack. Defaults to 7.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-X75Answer-N2Retransmissions 1.3.6.1.4.1.529.23.3.1.1.65
Number of retransmissions allowed. Defaults to 10.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-X75Answer-T1RetranTimer 1.3.6.1.4.1.529.23.3.1.1.66
Number of milliseconds between retransmissions. Defaults to 1000.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-X75Answer-FrameLength 1.3.6.1.4.1.529.23.3.1.1.67
Frame length to use for incoming X.75 connections. Defaults to 1024.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-FramedOnly 1.3.6.1.4.1.529.23.3.1.1.68
A profile can be restricted to only doing the framed commands (ppp, mpp, slip, and quit) by setting this to YES
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-HdlcNrmAnswer-Enabled 1.3.6.1.4.1.529.23.3.1.1.71
Set to yes to enable incoming HDLC-NRM calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-Visa2Answer-Enabled 1.3.6.1.4.1.529.23.3.1.1.72
Set to yes to enable incoming VISA2 calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-AtmAnswer-SvcEnabled 1.3.6.1.4.1.529.23.3.1.1.78
Set to yes to enable ATM SVC athentication on incoming calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-PriorityAnswer-Enabled 1.3.6.1.4.1.529.23.3.1.1.95
Enable priority classification.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

answerProfile-PriorityAnswer-PacketClassification 1.3.6.1.4.1.529.23.3.1.1.87
Method used to classify PPP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER qosTag(2), udpPortRange(3)  

answerProfile-PriorityAnswer-MaxRtpPacketDelay 1.3.6.1.4.1.529.23.3.1.1.88
Maximum delay for RTP packets in milli-seconds. Used for calculating the fragment size for the non-rtp traffic using the same link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PriorityAnswer-MinimumRtpPort 1.3.6.1.4.1.529.23.3.1.1.89
Minimum UDP port for prioritization
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PriorityAnswer-MaximumRtpPort 1.3.6.1.4.1.529.23.3.1.1.90
Maximum UDP port for prioritization
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-PriorityAnswer-NoHighPrioPktDuration 1.3.6.1.4.1.529.23.3.1.1.91
The number of seconds of no high priority packets before disabling IP fragmentation of low priority packets. The value 0 disables checking duration of no high priority packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

answerProfile-Action-o 1.3.6.1.4.1.529.23.3.1.1.69
Tok_String
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), createProfile(2), deleteProfile(3)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor