ASCEND-MIBXAUTH-MIB

File: ASCEND-MIBXAUTH-MIB.mib (52811 bytes)

Imported modules

ASCEND-MIB

RFC1155-SMI

RFC-1212

Imported symbols

configuration

IpAddress

OBJECT-TYPE

Defined Types

DisplayString
OCTET STRING

MibexternalAuthProfileEntry
SEQUENCE
	externalAuthProfile-Index-o	INTEGER
	externalAuthProfile-AuthType	INTEGER
	externalAuthProfile-AcctType	INTEGER
	externalAuthProfile-RadServEnable	INTEGER
	externalAuthProfile-RadAuthClient-AuthHost1	DisplayString
	externalAuthProfile-RadAuthClient-AuthHost2	DisplayString
	externalAuthProfile-RadAuthClient-AuthHost3	DisplayString
	externalAuthProfile-RadAuthClient-AuthPort	INTEGER
	externalAuthProfile-RadAuthClient-AuthSrcPort	INTEGER
	externalAuthProfile-RadAuthClient-AuthKey	DisplayString
	externalAuthProfile-RadAuthClient-AuthPool	INTEGER
	externalAuthProfile-RadAuthClient-AuthTimeout	INTEGER
	externalAuthProfile-RadAuthClient-AuthRspRequired	INTEGER
	externalAuthProfile-RadAuthClient-AuthIdFailReturnBusy	INTEGER
	externalAuthProfile-RadAuthClient-AuthIdTimeoutReturnBusy	INTEGER
	externalAuthProfile-RadAuthClient-AuthSessInterval	INTEGER
	externalAuthProfile-RadAuthClient-AuthTSSecure	INTEGER
	externalAuthProfile-RadAuthClient-AuthSend67	INTEGER
	externalAuthProfile-RadAuthClient-AuthFrmAdrStart	INTEGER
	externalAuthProfile-RadAuthClient-AuthBootHost	IpAddress
	externalAuthProfile-RadAuthClient-AuthBootHost2	IpAddress
	externalAuthProfile-RadAuthClient-AuthBootPort	INTEGER
	externalAuthProfile-RadAuthClient-AuthResetTime	INTEGER
	externalAuthProfile-RadAuthClient-AuthIdMaxRetryTime	INTEGER
	externalAuthProfile-RadAuthClient-AuthRadiusCompat	INTEGER
	externalAuthProfile-RadAuthClient-AuthKeepUserName	INTEGER
	externalAuthProfile-RadAuthClient-AuthRealmDelimiters	DisplayString
	externalAuthProfile-RadAuthClient-IdAuthPrefix	DisplayString
	externalAuthProfile-RadAuthClient-AllowAuthConfigRqsts	INTEGER
	externalAuthProfile-RadAuthClient-AuthReqDelimCount	INTEGER
	externalAuthProfile-RadAuthClient-AuthReqStripSide	INTEGER
	externalAuthProfile-RadAuthClient-AuthNetworkRouteServer	INTEGER
	externalAuthProfile-RadAuthClient-IdAuthPrefixX25	DisplayString
	externalAuthProfile-RadAuthClient-AllowUnencryptedTunnelPassword	INTEGER
	externalAuthProfile-RadAuthClient-AuthCliUserDnis	DisplayString
	externalAuthProfile-RadAuthClient-AllowNasPortTypeInCliUserAuth	INTEGER
	externalAuthProfile-RadAcctClient-AcctHost1	DisplayString
	externalAuthProfile-RadAcctClient-AcctHost2	DisplayString
	externalAuthProfile-RadAcctClient-AcctHost3	DisplayString
	externalAuthProfile-RadAcctClient-AcctPort	INTEGER
	externalAuthProfile-RadAcctClient-AcctSrcPort	INTEGER
	externalAuthProfile-RadAcctClient-AcctKey	DisplayString
	externalAuthProfile-RadAcctClient-AcctTimeout	INTEGER
	externalAuthProfile-RadAcctClient-AcctSessInterval	INTEGER
	externalAuthProfile-RadAcctClient-AcctIdBase	INTEGER
	externalAuthProfile-RadAcctClient-AcctResetTime	INTEGER
	externalAuthProfile-RadAcctClient-AcctCheckpoint	INTEGER
	externalAuthProfile-RadAcctClient-AcctCheckpointTimer	INTEGER
	externalAuthProfile-RadAcctClient-AcctStopOnly	INTEGER
	externalAuthProfile-RadAcctClient-AcctLimitRetry	INTEGER
	externalAuthProfile-RadAcctClient-AcctDropStopOnAuthFail	INTEGER
	externalAuthProfile-RadAcctClient-AcctRadiusCompat	INTEGER
	externalAuthProfile-RadAcctClient-TunnelAccounting	INTEGER
	externalAuthProfile-RadAcctClient-VoipAccounting	INTEGER
	externalAuthProfile-RadAcctClient-AcctOnSwitchover	INTEGER
	externalAuthProfile-RadAuthServer-AuthPort	INTEGER
	externalAuthProfile-RadAuthServer-AuthSessionKey	INTEGER
	externalAuthProfile-RadAuthServer-AuthAttributeType	INTEGER
	externalAuthProfile-RadAuthServer-AuthRadiusCompat	INTEGER
	externalAuthProfile-TacAuthClient-AuthServer1	IpAddress
	externalAuthProfile-TacAuthClient-AuthServer2	IpAddress
	externalAuthProfile-TacAuthClient-AuthServer3	IpAddress
	externalAuthProfile-TacAuthClient-AuthPort	INTEGER
	externalAuthProfile-TacAuthClient-AuthSrcPort	INTEGER
	externalAuthProfile-TacAuthClient-AuthKey	DisplayString
	externalAuthProfile-TacAuthClient-AuthTimeout	INTEGER
	externalAuthProfile-TacplusAuthClient-AuthServer1	IpAddress
	externalAuthProfile-TacplusAuthClient-AuthServer2	IpAddress
	externalAuthProfile-TacplusAuthClient-AuthServer3	IpAddress
	externalAuthProfile-TacplusAuthClient-AuthPort	INTEGER
	externalAuthProfile-TacplusAuthClient-AuthSrcPort	INTEGER
	externalAuthProfile-TacplusAuthClient-AuthKey	DisplayString
	externalAuthProfile-TacplusAuthClient-AuthTimeoutTime	INTEGER
	externalAuthProfile-TacplusAuthClient-AuthRetries	INTEGER
	externalAuthProfile-TacplusAcctClient-AcctServer1	IpAddress
	externalAuthProfile-TacplusAcctClient-AcctServer2	IpAddress
	externalAuthProfile-TacplusAcctClient-AcctServer3	IpAddress
	externalAuthProfile-TacplusAcctClient-AcctPort	INTEGER
	externalAuthProfile-TacplusAcctClient-AcctSrcPort	INTEGER
	externalAuthProfile-TacplusAcctClient-AcctKey	DisplayString
	externalAuthProfile-SecureidAuthClient-AuthServer1	IpAddress
	externalAuthProfile-SecureidAuthClient-AuthServer2	IpAddress
	externalAuthProfile-SecureidAuthClient-AuthServer3	IpAddress
	externalAuthProfile-SecureidAuthClient-AuthPort	INTEGER
	externalAuthProfile-SecureidAuthClient-AuthTimeout	INTEGER
	externalAuthProfile-SecureidAuthClient-AuthRetrycount	INTEGER
	externalAuthProfile-SecureidAuthClient-AuthDes	INTEGER
	externalAuthProfile-SecureidAuthClient-AuthNodeSecret	DisplayString
	externalAuthProfile-PasswordProfile-Clid	DisplayString
	externalAuthProfile-PasswordProfile-Dnis	DisplayString
	externalAuthProfile-PasswordProfile-Banner	DisplayString
	externalAuthProfile-PasswordProfile-InitBanner	DisplayString
	externalAuthProfile-PasswordProfile-Pool	DisplayString
	externalAuthProfile-PasswordProfile-Frdl	DisplayString
	externalAuthProfile-PasswordProfile-Dialout	DisplayString
	externalAuthProfile-PasswordProfile-DialoutRoutes	DisplayString
	externalAuthProfile-PasswordProfile-DialoutIpxRoutes	DisplayString
	externalAuthProfile-PasswordProfile-DialoutAtalkRoutes	DisplayString
	externalAuthProfile-PasswordProfile-SourceAuth	DisplayString
	externalAuthProfile-LocalProfilesFirst	INTEGER
	externalAuthProfile-Noattr6UseTermsrv	INTEGER
	externalAuthProfile-Clid	DisplayString
	externalAuthProfile-Dnis	DisplayString
	externalAuthProfile-CliUserAuth	INTEGER
	externalAuthProfile-Action-o	INTEGER

MibexternalAuthProfile-RadAuthServer-AuthKeyEntry
SEQUENCE
	externalAuthProfile-RadAuthServer-AuthKey-Index-o	INTEGER
	externalAuthProfile-RadAuthServer-AuthKey-Index1-o	INTEGER
	externalAuthProfile-RadAuthServer-AuthKey	DisplayString

MibexternalAuthProfile-RadAuthServer-AuthNetmaskEntry
SEQUENCE
	externalAuthProfile-RadAuthServer-AuthNetmask-Index-o	INTEGER
	externalAuthProfile-RadAuthServer-AuthNetmask-Index1-o	INTEGER
	externalAuthProfile-RadAuthServer-AuthNetmask	IpAddress

MibexternalAuthProfile-RadAuthServer-AuthClientEntry
SEQUENCE
	externalAuthProfile-RadAuthServer-AuthClient-Index-o	INTEGER
	externalAuthProfile-RadAuthServer-AuthClient-Index1-o	INTEGER
	externalAuthProfile-RadAuthServer-AuthClient	IpAddress

MibradStatProfileEntry
SEQUENCE
	radStatProfile-Index-o	INTEGER
	radStatProfile-CurrentAuthServer	INTEGER
	radStatProfile-CurrentAcctServer	INTEGER
	radStatProfile-Action-o	INTEGER

MibradAcctCallLogProfileEntry
SEQUENCE
	radAcctCallLogProfile-Index-o	INTEGER
	radAcctCallLogProfile-CallLogEnable	INTEGER
	radAcctCallLogProfile-CallLogHost1	IpAddress
	radAcctCallLogProfile-CallLogHost2	IpAddress
	radAcctCallLogProfile-CallLogHost3	IpAddress
	radAcctCallLogProfile-CallLogPort	INTEGER
	radAcctCallLogProfile-CallLogKey	DisplayString
	radAcctCallLogProfile-CallLogTimeout	INTEGER
	radAcctCallLogProfile-CallLogIdBase	INTEGER
	radAcctCallLogProfile-CallLogResetTime	INTEGER
	radAcctCallLogProfile-CallLogStopOnly	INTEGER
	radAcctCallLogProfile-CallLogLimitRetry	INTEGER
	radAcctCallLogProfile-CallLogServerIndex	INTEGER
	radAcctCallLogProfile-CallLogRadiusCompat	INTEGER
	radAcctCallLogProfile-CallLogMultiPacket	INTEGER
	radAcctCallLogProfile-CallLogStreamPeriod	INTEGER
	radAcctCallLogProfile-CallLogConnectionPacketsEnable	INTEGER
	radAcctCallLogProfile-CallLogCsmModemDiag	INTEGER
	radAcctCallLogProfile-VoipCallLogging	INTEGER
	radAcctCallLogProfile-CallLogSwitchover	INTEGER
	radAcctCallLogProfile-Action-o	INTEGER

Defined Values

mibexternalAuthProfile		1.3.6.1.4.1.529.23.142
OBJECT IDENTIFIER

mibradStatProfile		1.3.6.1.4.1.529.23.141
OBJECT IDENTIFIER

mibradAcctCallLogProfile		1.3.6.1.4.1.529.23.143
OBJECT IDENTIFIER

mibexternalAuthProfileTable		1.3.6.1.4.1.529.23.142.1
A list of mibexternalAuthProfile profile entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MibexternalAuthProfileEntry

mibexternalAuthProfileEntry		1.3.6.1.4.1.529.23.142.1.1
A mibexternalAuthProfile entry containing objects that maps to the parameters of mibexternalAuthProfile profile.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MibexternalAuthProfileEntry

externalAuthProfile-Index-o		1.3.6.1.4.1.529.23.142.1.1.1
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

externalAuthProfile-AuthType		1.3.6.1.4.1.529.23.142.1.1.2
The type of authentication to perform.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), tACACS(2), rADIUS(3), rADIUS-LOGOUT(4), sECURID(5), tACACSPLUS(6), dEFENDER(7)

externalAuthProfile-AcctType		1.3.6.1.4.1.529.23.142.1.1.3
The type of accounting to perform.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), radius(2), tacacsplus(3)

externalAuthProfile-RadServEnable		1.3.6.1.4.1.529.23.142.1.1.4
Whether or not the on-board RADIUS server is enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-AuthHost1		1.3.6.1.4.1.529.23.142.1.1.104
The IP address/hostname of the first RADIUS authentication server
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAuthClient-AuthHost2		1.3.6.1.4.1.529.23.142.1.1.105
The IP address/hostname of the second RADIUS authentication server
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAuthClient-AuthHost3		1.3.6.1.4.1.529.23.142.1.1.106
The IP address/hostname of the third RADIUS authentication server
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAuthClient-AuthPort		1.3.6.1.4.1.529.23.142.1.1.8
The UDP destination port to use for RADIUS authentication.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthClient-AuthSrcPort		1.3.6.1.4.1.529.23.142.1.1.9
The UDP source port to use for RADIUS authentication. If zero, the source port is selected from the non-privileged port range (1024-2000).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthClient-AuthKey		1.3.6.1.4.1.529.23.142.1.1.10
The RADIUS authentication access key shared with the RADIUS server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAuthClient-AuthPool		1.3.6.1.4.1.529.23.142.1.1.11
If TRUE an IP address is allocated from the default pool and passed to the RADIUS server during RADIUS authentication. This address may be assigned to the dial-in user for the duration of the connection.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-AuthTimeout		1.3.6.1.4.1.529.23.142.1.1.12
Number of seconds between retries to the authentication host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthClient-AuthRspRequired		1.3.6.1.4.1.529.23.142.1.1.13
When set to Yes, entry is allowed only if the authentication server responds with an authentication of the login information. When set to No, entry is also allowed if there is no response from the authentication server. This field is used only for CLID or DNIS authentication.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-AuthIdFailReturnBusy		1.3.6.1.4.1.529.23.142.1.1.14
Return busy instead of normal call clearing when id authentication fails.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-AuthIdTimeoutReturnBusy		1.3.6.1.4.1.529.23.142.1.1.15
Return busy instead of normal call clearing when external id authentication fails.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-AuthSessInterval		1.3.6.1.4.1.529.23.142.1.1.16
Send the number-of-sessions-per-Class Attribute to the authentication server every auth-sess-interval seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthClient-AuthTSSecure		1.3.6.1.4.1.529.23.142.1.1.17
Allow access to terminal server when RADIUS Login-Host is not specify when authTSsecure is set no
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-AuthSend67		1.3.6.1.4.1.529.23.142.1.1.18
If Yes, default attributes 6,7 of Radius and send them in the authentication request.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-AuthFrmAdrStart		1.3.6.1.4.1.529.23.142.1.1.19
Set Yes to send a second Radius accounting start record when the Framed-Address is assigned. Default No for backward compatibility.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-AuthBootHost		1.3.6.1.4.1.529.23.142.1.1.20
The IP address of the authentication boot host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-RadAuthClient-AuthBootHost2		1.3.6.1.4.1.529.23.142.1.1.21
The IP address of the secondary authentication boot host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-RadAuthClient-AuthBootPort		1.3.6.1.4.1.529.23.142.1.1.22
The UDP port to use for RADIUS authentication.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthClient-AuthResetTime		1.3.6.1.4.1.529.23.142.1.1.23
The time to reset to the primary server after it has failed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthClient-AuthIdMaxRetryTime		1.3.6.1.4.1.529.23.142.1.1.24
Maximum time limit to spend retrying RADIUS servers when in id authentication, a value of 0 sets the limit to the internal default value.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthClient-AuthRadiusCompat		1.3.6.1.4.1.529.23.142.1.1.25
Authentication RADIUS compatibility mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	oldAscend(1), vendorSpecific(2), n-16BitVendorSpecific(3)

externalAuthProfile-RadAuthClient-AuthKeepUserName		1.3.6.1.4.1.529.23.142.1.1.26
Action if the Access-Accept packet from Radius server contains a User-Name attribute.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	changeName(1), keepName(2), keepRealmName(3)

externalAuthProfile-RadAuthClient-AuthRealmDelimiters		1.3.6.1.4.1.529.23.142.1.1.27
Characters that delimit a realm and user name (used only if auth-keep-user-name=keep-realm-name or radius-delim_count>0)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAuthClient-IdAuthPrefix		1.3.6.1.4.1.529.23.142.1.1.28
A short text string prepended to the username portion of a CLID or DNIS authentication request.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAuthClient-AllowAuthConfigRqsts		1.3.6.1.4.1.529.23.142.1.1.29
Set Yes to send External Config Requests. Default is set to Yes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-AuthReqDelimCount		1.3.6.1.4.1.529.23.142.1.1.30
Number of delimiters to strip from a username in Radius Auth request.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthClient-AuthReqStripSide		1.3.6.1.4.1.529.23.142.1.1.31
Side to strip chars from a username in a Radius Auth request if delim-count is > 0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), left(2), right(3)

externalAuthProfile-RadAuthClient-AuthNetworkRouteServer		1.3.6.1.4.1.529.23.142.1.1.98
Determines whether Radius server supports multiple profiles with the same user-name. Otherwise destination IP address is appended to user-name.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-IdAuthPrefixX25		1.3.6.1.4.1.529.23.142.1.1.99
A short text string prepended to the username portion of a DNIS authentication request for X25 calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAuthClient-AllowUnencryptedTunnelPassword		1.3.6.1.4.1.529.23.142.1.1.101
When set to 'YES', unencrypted as well as encrypted Tunnel-Password, from RADIUS, is accepted. When set to 'NO' only encrypted Tunnel-Password, from RADIUS, is accepted. But as per RFC 2868 the Tunnel-Password MUST be encrypted by RADIUS before sending out.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthClient-AuthCliUserDnis		1.3.6.1.4.1.529.23.142.1.1.102
Pseudo DNIS number for CLI users. If set, this number is sent to RADIUS as DNIS. If not set, DNIS is not sent to RADIUS.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAuthClient-AllowNasPortTypeInCliUserAuth		1.3.6.1.4.1.529.23.142.1.1.103
When set to 'NO', NAS_Port_Type attribute is NOT sent in the RADIUS authentication request packet while authenticating CLI users. Default is set to Yes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAcctClient-AcctHost1		1.3.6.1.4.1.529.23.142.1.1.107
The IP address/hostname of the first RADIUS accounting server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAcctClient-AcctHost2		1.3.6.1.4.1.529.23.142.1.1.108
The IP address/hostname of the second RADIUS accounting server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAcctClient-AcctHost3		1.3.6.1.4.1.529.23.142.1.1.109
The IP address/hostname of the third RADIUS accounting server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAcctClient-AcctPort		1.3.6.1.4.1.529.23.142.1.1.35
The UDP destination port to use for RADIUS accounting.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAcctClient-AcctSrcPort		1.3.6.1.4.1.529.23.142.1.1.36
The UDP source port to use for RADIUS accounting. If zero, the source port is selected from the non-privileged port range (1024-2000).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAcctClient-AcctKey		1.3.6.1.4.1.529.23.142.1.1.37
The RADIUS accounting access key shared with the RADIUS server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-RadAcctClient-AcctTimeout		1.3.6.1.4.1.529.23.142.1.1.38
Number of seconds to wait for a response to previous accounting request.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAcctClient-AcctSessInterval		1.3.6.1.4.1.529.23.142.1.1.39
Send the number-of-sessions-per-Class Attribute to the accounting server every acct-sess-interval seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAcctClient-AcctIdBase		1.3.6.1.4.1.529.23.142.1.1.40
The base value to use in reporting Account ID.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	acctBase10(1), acctBase16(2)

externalAuthProfile-RadAcctClient-AcctResetTime		1.3.6.1.4.1.529.23.142.1.1.41
The elapsed time to reset to the primary server, after failing to reach the primary server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAcctClient-AcctCheckpoint		1.3.6.1.4.1.529.23.142.1.1.42
Interval at which to send checkpoint packets to the daemon in minutes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAcctClient-AcctCheckpointTimer		1.3.6.1.4.1.529.23.142.1.1.43
Sets the scope of the checkpoint timer to individual sessions or all-sessions.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	perSession(1), allSessions(2)

externalAuthProfile-RadAcctClient-AcctStopOnly		1.3.6.1.4.1.529.23.142.1.1.44
Send to RADIUS Accounting Stop packets that have username=0. These are caused by connections that are dropped before authentication is done.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAcctClient-AcctLimitRetry		1.3.6.1.4.1.529.23.142.1.1.45
Number of retries before removing RADIUS Acct packet. 0 means leave on retry list until maximum retry entries are exceeded.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAcctClient-AcctDropStopOnAuthFail		1.3.6.1.4.1.529.23.142.1.1.46
If Yes, do not send RADIUS Accounting Stop/Checkpoint packets for users that failed authentication.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAcctClient-AcctRadiusCompat		1.3.6.1.4.1.529.23.142.1.1.47
Accounting RADIUS compatibility mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	oldAscend(1), vendorSpecific(2), n-16BitVendorSpecific(3)

externalAuthProfile-RadAcctClient-TunnelAccounting		1.3.6.1.4.1.529.23.142.1.1.48
Perform RFC2867 Radius Tunnel Accounting ( L2F, L2TP ).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAcctClient-VoipAccounting		1.3.6.1.4.1.529.23.142.1.1.110
To Enable/Disable radius accounting for VOIP calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAcctClient-AcctOnSwitchover		1.3.6.1.4.1.529.23.142.1.1.111
Determines whether Accounting-on packet with event Ascend-Controller-Switchover should be sent or not during switchover when syncing is enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthServer-AuthPort		1.3.6.1.4.1.529.23.142.1.1.49
The UDP port to use for the on-board RADIUS server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthServer-AuthSessionKey		1.3.6.1.4.1.529.23.142.1.1.50
Enables Session key assignments.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-RadAuthServer-AuthAttributeType		1.3.6.1.4.1.529.23.142.1.1.51
The type of attributes required for session matching.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	radServAttrAny(1), radServAttrKey(2), radServAttrAll(3)

externalAuthProfile-RadAuthServer-AuthRadiusCompat		1.3.6.1.4.1.529.23.142.1.1.52
RADIUS server RADIUS compatibility mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	oldAscend(1), vendorSpecific(2), n-16BitVendorSpecific(3)

externalAuthProfile-TacAuthClient-AuthServer1		1.3.6.1.4.1.529.23.142.1.1.53
The IP address of the first TACACS authentication server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-TacAuthClient-AuthServer2		1.3.6.1.4.1.529.23.142.1.1.54
The IP address of the second TACACS authentication server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-TacAuthClient-AuthServer3		1.3.6.1.4.1.529.23.142.1.1.55
The IP address of the third TACACS authentication server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-TacAuthClient-AuthPort		1.3.6.1.4.1.529.23.142.1.1.56
The UDP port to use for TACACS authentication.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-TacAuthClient-AuthSrcPort		1.3.6.1.4.1.529.23.142.1.1.57
The UDP source port to use for TACACS authentication. If zero, the source port is selected from the non-privileged port range (1024-2000).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-TacAuthClient-AuthKey		1.3.6.1.4.1.529.23.142.1.1.58
The RADIUS authentication access key shared with the RADIUS server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-TacAuthClient-AuthTimeout		1.3.6.1.4.1.529.23.142.1.1.59
Number of seconds between retries to the authentication host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-TacplusAuthClient-AuthServer1		1.3.6.1.4.1.529.23.142.1.1.60
The IP address of the first TACACS+ authentication server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-TacplusAuthClient-AuthServer2		1.3.6.1.4.1.529.23.142.1.1.61
The IP address of the second TACACS+ authentication server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-TacplusAuthClient-AuthServer3		1.3.6.1.4.1.529.23.142.1.1.62
The IP address of the third TACACS+ authentication server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-TacplusAuthClient-AuthPort		1.3.6.1.4.1.529.23.142.1.1.63
The TCP destination port to use for TACACS+ authentication.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-TacplusAuthClient-AuthSrcPort		1.3.6.1.4.1.529.23.142.1.1.64
The TCP source port to use for TACACS+ authentication. If zero, the source port is selected from the non-privileged port range (1024-2000).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-TacplusAuthClient-AuthKey		1.3.6.1.4.1.529.23.142.1.1.65
The Tacacs+ authentication access key shared with the TACACS+ server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-TacplusAuthClient-AuthTimeoutTime		1.3.6.1.4.1.529.23.142.1.1.66
The time to reset to the primary server after it has failed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-TacplusAuthClient-AuthRetries		1.3.6.1.4.1.529.23.142.1.1.67
The number of times to retry the auth hosts before giving up.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-TacplusAcctClient-AcctServer1		1.3.6.1.4.1.529.23.142.1.1.68
The IP address of the first TACACS+ accounting server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-TacplusAcctClient-AcctServer2		1.3.6.1.4.1.529.23.142.1.1.69
The IP address of the second TACACS+ accounting server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-TacplusAcctClient-AcctServer3		1.3.6.1.4.1.529.23.142.1.1.70
The IP address of the third TACACS+ accounting server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-TacplusAcctClient-AcctPort		1.3.6.1.4.1.529.23.142.1.1.71
The TCP destination port to use for TACACS+ accounting.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-TacplusAcctClient-AcctSrcPort		1.3.6.1.4.1.529.23.142.1.1.72
The TCP source port to use for TACACS+ accounting. If zero, the source port is selected from the non-privileged port range (1024-2000).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-TacplusAcctClient-AcctKey		1.3.6.1.4.1.529.23.142.1.1.73
The TACACS+ accounting access key shared with the TACACS+ server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-SecureidAuthClient-AuthServer1		1.3.6.1.4.1.529.23.142.1.1.74
The IP address of the first authentication server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-SecureidAuthClient-AuthServer2		1.3.6.1.4.1.529.23.142.1.1.75
The IP address of the second authentication server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-SecureidAuthClient-AuthServer3		1.3.6.1.4.1.529.23.142.1.1.76
The IP address of the third authentication server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

externalAuthProfile-SecureidAuthClient-AuthPort		1.3.6.1.4.1.529.23.142.1.1.77
The UDP destination port to use for authentication.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-SecureidAuthClient-AuthTimeout		1.3.6.1.4.1.529.23.142.1.1.78
Number of seconds between retries to the authentication host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-SecureidAuthClient-AuthRetrycount		1.3.6.1.4.1.529.23.142.1.1.79
Number of times to retry an authentication attempt.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

externalAuthProfile-SecureidAuthClient-AuthDes		1.3.6.1.4.1.529.23.142.1.1.80
Use DES encryption instead of native encryption.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-SecureidAuthClient-AuthNodeSecret		1.3.6.1.4.1.529.23.142.1.1.81
node secret assigned to this router, hexadecimal notation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-PasswordProfile-Clid		1.3.6.1.4.1.529.23.142.1.1.82
This is the password for the CLID pseudo user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-PasswordProfile-Dnis		1.3.6.1.4.1.529.23.142.1.1.83
This is the password for the DNIS pseudo user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-PasswordProfile-InitBanner		1.3.6.1.4.1.529.23.142.1.1.85
Authenticate DNIS using this password.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-PasswordProfile-Pool		1.3.6.1.4.1.529.23.142.1.1.86
This is the password for the POOLs pseudo user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-PasswordProfile-Frdl		1.3.6.1.4.1.529.23.142.1.1.87
This is the password for the Frame Relay pseudo user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-PasswordProfile-Dialout		1.3.6.1.4.1.529.23.142.1.1.88
This is the password for the Dialout pseudo user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-PasswordProfile-DialoutRoutes		1.3.6.1.4.1.529.23.142.1.1.89
This is the password for the Dialout Routes pseudo user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-PasswordProfile-DialoutIpxRoutes		1.3.6.1.4.1.529.23.142.1.1.90
This is the password for the Dialout IPX pseudo user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-PasswordProfile-DialoutAtalkRoutes		1.3.6.1.4.1.529.23.142.1.1.91
This is the password for the Dialout Appletalk pseudo user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-PasswordProfile-SourceAuth		1.3.6.1.4.1.529.23.142.1.1.92
This is the password for the Source Auth pseudo user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-LocalProfilesFirst		1.3.6.1.4.1.529.23.142.1.1.93
Authenticate using local profiles first.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	lpfNo(1), lpfYes(2), lpfRno(3)

externalAuthProfile-Noattr6UseTermsrv		1.3.6.1.4.1.529.23.142.1.1.94
Using terminal server if attribute 6 is missing from RADIUS authentication.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

externalAuthProfile-Clid		1.3.6.1.4.1.529.23.142.1.1.95
Authenticate CLID using this password.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-Dnis		1.3.6.1.4.1.529.23.142.1.1.96
Authenticate DNIS using this password.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

externalAuthProfile-CliUserAuth		1.3.6.1.4.1.529.23.142.1.1.100
Authenticate the user Locally or Externally in the sequence specified by this filed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	localOnly(1), localThenExternal(2), externalOnly(3), externalThenLocal(4), externalThenLocalIfTimeout(5)

externalAuthProfile-Action-o		1.3.6.1.4.1.529.23.142.1.1.97
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noAction(1), createProfile(2), deleteProfile(3)

mibexternalAuthProfile-RadAuthServer-AuthKeyTable		1.3.6.1.4.1.529.23.142.2
A list of mibexternalAuthProfile__rad_auth_server__auth_key profile entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MibexternalAuthProfile-RadAuthServer-AuthKeyEntry

mibexternalAuthProfile-RadAuthServer-AuthKeyEntry		1.3.6.1.4.1.529.23.142.2.1
A mibexternalAuthProfile__rad_auth_server__auth_key entry containing objects that maps to the parameters of mibexternalAuthProfile__rad_auth_server__auth_key profile.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MibexternalAuthProfile-RadAuthServer-AuthKeyEntry

externalAuthProfile-RadAuthServer-AuthKey-Index-o		1.3.6.1.4.1.529.23.142.2.1.1
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthServer-AuthKey-Index1-o		1.3.6.1.4.1.529.23.142.2.1.2
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthServer-AuthKey		1.3.6.1.4.1.529.23.142.2.1.3
The on-board RADIUS server key, shared with the RADIUS clients.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

mibexternalAuthProfile-RadAuthServer-AuthNetmaskTable		1.3.6.1.4.1.529.23.142.3
A list of mibexternalAuthProfile__rad_auth_server__auth_netmask profile entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MibexternalAuthProfile-RadAuthServer-AuthNetmaskEntry

mibexternalAuthProfile-RadAuthServer-AuthNetmaskEntry		1.3.6.1.4.1.529.23.142.3.1
A mibexternalAuthProfile__rad_auth_server__auth_netmask entry containing objects that maps to the parameters of mibexternalAuthProfile__rad_auth_server__auth_netmask profile.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MibexternalAuthProfile-RadAuthServer-AuthNetmaskEntry

externalAuthProfile-RadAuthServer-AuthNetmask-Index-o		1.3.6.1.4.1.529.23.142.3.1.1
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthServer-AuthNetmask-Index1-o		1.3.6.1.4.1.529.23.142.3.1.2
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthServer-AuthNetmask		1.3.6.1.4.1.529.23.142.3.1.3
The IP netmask of the RADIUS clients.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

mibexternalAuthProfile-RadAuthServer-AuthClientTable		1.3.6.1.4.1.529.23.142.4
A list of mibexternalAuthProfile__rad_auth_server__auth_client profile entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MibexternalAuthProfile-RadAuthServer-AuthClientEntry

mibexternalAuthProfile-RadAuthServer-AuthClientEntry		1.3.6.1.4.1.529.23.142.4.1
A mibexternalAuthProfile__rad_auth_server__auth_client entry containing objects that maps to the parameters of mibexternalAuthProfile__rad_auth_server__auth_client profile.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MibexternalAuthProfile-RadAuthServer-AuthClientEntry

externalAuthProfile-RadAuthServer-AuthClient-Index-o		1.3.6.1.4.1.529.23.142.4.1.1
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthServer-AuthClient-Index1-o		1.3.6.1.4.1.529.23.142.4.1.2
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

externalAuthProfile-RadAuthServer-AuthClient		1.3.6.1.4.1.529.23.142.4.1.3
The IP address of the RADIUS clients.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

mibradStatProfileTable		1.3.6.1.4.1.529.23.141.1
A list of mibradStatProfile profile entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MibradStatProfileEntry

mibradStatProfileEntry		1.3.6.1.4.1.529.23.141.1.1
A mibradStatProfile entry containing objects that maps to the parameters of mibradStatProfile profile.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MibradStatProfileEntry

radStatProfile-Index-o		1.3.6.1.4.1.529.23.141.1.1.1
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

radStatProfile-CurrentAuthServer		1.3.6.1.4.1.529.23.141.1.1.2
The index of the current RADIUS authentication server.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

radStatProfile-CurrentAcctServer		1.3.6.1.4.1.529.23.141.1.1.3
The index of the current RADIUS accounting server.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

radStatProfile-Action-o		1.3.6.1.4.1.529.23.141.1.1.4
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noAction(1), createProfile(2), deleteProfile(3)

mibradAcctCallLogProfileTable		1.3.6.1.4.1.529.23.143.1
A list of mibradAcctCallLogProfile profile entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MibradAcctCallLogProfileEntry

mibradAcctCallLogProfileEntry		1.3.6.1.4.1.529.23.143.1.1
A mibradAcctCallLogProfile entry containing objects that maps to the parameters of mibradAcctCallLogProfile profile.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MibradAcctCallLogProfileEntry

radAcctCallLogProfile-Index-o		1.3.6.1.4.1.529.23.143.1.1.1
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

radAcctCallLogProfile-CallLogEnable		1.3.6.1.4.1.529.23.143.1.1.2
Enable call log support.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

radAcctCallLogProfile-CallLogHost1		1.3.6.1.4.1.529.23.143.1.1.3
The IP address of the first (RADIUS_ACCT) call log host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

radAcctCallLogProfile-CallLogHost2		1.3.6.1.4.1.529.23.143.1.1.4
The IP address of the second (RADIUS_ACCT) call log host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

radAcctCallLogProfile-CallLogHost3		1.3.6.1.4.1.529.23.143.1.1.5
The IP address of the third (RADIUS_ACCT) call log host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

radAcctCallLogProfile-CallLogPort		1.3.6.1.4.1.529.23.143.1.1.6
The UDP port to use for (RADIUS_ACCT) call log accounting.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

radAcctCallLogProfile-CallLogKey		1.3.6.1.4.1.529.23.143.1.1.7
The (RADIUS_ACCT) call log accounting key.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

radAcctCallLogProfile-CallLogTimeout		1.3.6.1.4.1.529.23.143.1.1.8
Number of seconds to wait for a response to previous call log accounting request.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

radAcctCallLogProfile-CallLogIdBase		1.3.6.1.4.1.529.23.143.1.1.9
The Base to use in reporting Account ID.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	acctBase10(1), acctBase16(2)

radAcctCallLogProfile-CallLogResetTime		1.3.6.1.4.1.529.23.143.1.1.10
The timer to reset to the primary server(host-1) after current host is changed to host-2 or host-3. Value is in seconds. If value is 0, no timer is run.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

radAcctCallLogProfile-CallLogStopOnly		1.3.6.1.4.1.529.23.143.1.1.11
Send call log Stop packets that have username=0. These are caused by connections that are dropped before authentication is done.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

radAcctCallLogProfile-CallLogLimitRetry		1.3.6.1.4.1.529.23.143.1.1.12
Number of retries before removing call log packet. 0 means leave on retry list until maximum retry entries are exceeded.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

radAcctCallLogProfile-CallLogServerIndex		1.3.6.1.4.1.529.23.143.1.1.14
The currently active call Logging server Index. The default factory setting is host-1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	host1(1), host2(2), host3(3)

radAcctCallLogProfile-CallLogRadiusCompat		1.3.6.1.4.1.529.23.143.1.1.13
Call Logging RADIUS compatibility mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	vendorSpecific(1), n-16BitVendorSpecific(2)

radAcctCallLogProfile-CallLogMultiPacket		1.3.6.1.4.1.529.23.143.1.1.15
Call Logging MultiPacket Enable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

radAcctCallLogProfile-CallLogStreamPeriod		1.3.6.1.4.1.529.23.143.1.1.16
Number of minutes between snapshots for stream pkts.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

radAcctCallLogProfile-CallLogConnectionPacketsEnable		1.3.6.1.4.1.529.23.143.1.1.17
Enable/Disable call logging START/STOP pkts when connection comes up or goes down. This is opposed to line statistics call logging which is always enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

radAcctCallLogProfile-CallLogCsmModemDiag		1.3.6.1.4.1.529.23.143.1.1.18
Enable CSM Modem diagnostics in Call Logging
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

radAcctCallLogProfile-VoipCallLogging		1.3.6.1.4.1.529.23.143.1.1.20
To Enable/Disable call logging for VOIP calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

radAcctCallLogProfile-CallLogSwitchover		1.3.6.1.4.1.529.23.143.1.1.21
Determines whether Accounting-on packet with event Ascend-Control-Module-Switchover should be sent or not during switchover when syncing is enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

radAcctCallLogProfile-Action-o		1.3.6.1.4.1.529.23.143.1.1.19
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noAction(1), createProfile(2), deleteProfile(3)

externalAuthProfile-PasswordProfile-Banner		1.3.6.1.4.1.529.23.142.1.1.84
This is the password for the Banner pseudo user.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString