ASKEY-SYSTEM-MIB

File: ASKEY-SYSTEM-MIB.mib (65908 bytes)

Imported modules

IF-MIB	SNMPv2-SMI	RFC1213-MIB
SNMPv2-TC	INET-ADDRESS-MIB	P-BRIDGE-MIB
ASKEY-DSLAM-MIB	SNMP-FRAMEWORK-MIB	ASKEY-ENTITY-ALARM-MIB

Imported symbols

ifIndex	InterfaceIndex	MODULE-IDENTITY
OBJECT-TYPE	IpAddress	Unsigned32
Counter32	TimeTicks	DisplayString
RowStatus	TEXTUAL-CONVENTION	InetAddress
EnabledStatus	ipDslam	SnmpAdminString
aeAlarmPhysicalIndex

Defined Types

MacAddress
OCTET STRING	Size(6)

IPSectionIndex
A unique value, greater than zero, for denoting an IP section. The IP section represents a range of the IP address from some IP to another IP.
TEXTUAL-CONVENTION
	INTEGER	1..10

VLANList
Each octet within this value specifies a set of eight VLAN IDs, with the first octet specifying VLAN ID 0 through 7, the second octet specifying VLAN ID 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VLAN ID, and the least significant bit represents the highest numbered VLAN ID. Thus, each VLAN ID is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is included in the set of VLANs; the VLAN is not included if its bit has a value of '0'.
TEXTUAL-CONVENTION
	OCTET STRING

SnmpTrapEntry
SEQUENCE
	snmpTrapStation	IpAddress
	snmpTrapCommunity	DisplayString
	snmpTrapSNMPVersion	INTEGER
	snmpTrapRowStatus	RowStatus

SnmpCommunityEntry
SEQUENCE
	snmpCommunityName	DisplayString
	snmpCommunityPermission	INTEGER
	snmpCommunityRowStatus	RowStatus

AskeyDslamFdbEntry
SEQUENCE
	fdbMacIndex	INTEGER
	fdbVpi	INTEGER
	fdbVci	INTEGER
	macAddress	MacAddress
	askeyDslamFdbStatus	INTEGER

AskeyCardInfoEntry
SEQUENCE
	askeyCardPlannedType	INTEGER
	askeyCardType	INTEGER
	askeyCardHWVersion	DisplayString
	askeyCardSWVersion	DisplayString
	askeyCardImage	DisplayString
	askeyCardUptime	INTEGER
	askeyCardRole	INTEGER
	askeyCardSerialNumber	DisplayString
	askeyCardAdminStatus	INTEGER
	askeyCardOperStatus	INTEGER
	lineCardAdminVlanTagPassEnabled	INTEGER
	lineCardOperVlanTagPassEnabled	INTEGER
	lineCardAdminRfc2684Encap	INTEGER
	lineCardOperRfc2684Encap	INTEGER
	lineCardServiceTypeControl	INTEGER
	shdslFirmwareUpgrade	INTEGER
	shdslFirmwareUpgradeState	INTEGER
	taggedModeAdminStatus	INTEGER
	taggedModeOperStatus	INTEGER

LinePortInfoEntry
SEQUENCE
	linePortAdminStatus	INTEGER
	linePortOperStatus	INTEGER
	circuitID	SnmpAdminString
	remoteID	SnmpAdminString

AskeySystemManagementInfoVlanMacLimitEntry
SEQUENCE
	askeySystemManagementInfoVlanID	INTEGER
	askeySystemManagementInfoVlanMacLimit	INTEGER
	askeySystemManagementInfoVlanMacLimitEnabled	INTEGER

AskeyCosQueueMappingEntry
SEQUENCE
	askeyCosQueueMapping8021p	INTEGER
	askeyCosQueueIndex	INTEGER

AskeySystemUserAccountEntry
SEQUENCE
	askeySystemUserAccountUserName	SnmpAdminString
	askeySystemUserAccountPassword	SnmpAdminString
	askeySystemUserAccountGroup	INTEGER
	askeySystemUserAccountRowStatus	RowStatus

UgeAutoNegotionEntry
SEQUENCE
	autoNegotiationState	INTEGER

UgePauseFrameStatisticEntry
SEQUENCE
	rxPausePackets	Unsigned32
	txPausePackets	Unsigned32

SubtendVLANEntry
SEQUENCE
	subtendState	INTEGER
	subtendVLAN	VLANList

UgeVLANEntry
SEQUENCE
	ugeVLAN	VLANList

SecuredHostEntry
SEQUENCE
	securedIPSectorIndex	IPSectionIndex
	securedIPSectorStartIP	IpAddress
	securedIPSectorEndIP	IpAddress
	allowedServiceType	BITS

Defined Values

askeySystemMib		1.3.6.1.4.1.3646.1300.2.1
ASKEY ADSL MIB OID defines and documentation.
MODULE-IDENTITY

ipConfig		1.3.6.1.4.1.3646.1300.2.1.1
OBJECT IDENTIFIER

nodeIP		1.3.6.1.4.1.3646.1300.2.1.1.1
OBJECT IDENTIFIER

nodeIPAddr		1.3.6.1.4.1.3646.1300.2.1.1.1.1
The IP address of node. It applies to the trunk (up-link) port.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

nodeIPNetMask		1.3.6.1.4.1.3646.1300.2.1.1.1.2
The subnet mask associated with the IP address of this node. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

nodeMACAddr		1.3.6.1.4.1.3646.1300.2.1.1.1.3
The MAC address of the trunk (up-link) port.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

gatewayIPAddr		1.3.6.1.4.1.3646.1300.2.1.1.1.4
The gateway IP address of node. It applies to the trunk (up-link) port.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

mgmtIP		1.3.6.1.4.1.3646.1300.2.1.1.2
OBJECT IDENTIFIER

mgmtIPAddr		1.3.6.1.4.1.3646.1300.2.1.1.2.1
The IP address of the management (out-band) port.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

mgmtIPNetMask		1.3.6.1.4.1.3646.1300.2.1.1.2.2
The subnet mask associated with the IP address of the management port. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

mgmtMACAddr		1.3.6.1.4.1.3646.1300.2.1.1.2.3
The MAC address of the manaement (out-band) port.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

nodeTime		1.3.6.1.4.1.3646.1300.2.1.2
OBJECT IDENTIFIER

time		1.3.6.1.4.1.3646.1300.2.1.2.1
The time of the system.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(14..19)

zone		1.3.6.1.4.1.3646.1300.2.1.2.2
The time zone of the system.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	-12..13

snmpTrapMib		1.3.6.1.4.1.3646.1300.2.1.6
OBJECT IDENTIFIER

snmpTrapTable		1.3.6.1.4.1.3646.1300.2.1.6.1
This table contains information for SNMP Trap.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SnmpTrapEntry

snmpTrapEntry		1.3.6.1.4.1.3646.1300.2.1.6.1.1
An entry of parameters in snmpTrap table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpTrapEntry

snmpTrapStation		1.3.6.1.4.1.3646.1300.2.1.6.1.1.1
The IP address of the workstation which the SNMP Trap is sent to.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

snmpTrapCommunity		1.3.6.1.4.1.3646.1300.2.1.6.1.1.2
DURABLE: { 'public','':all } The SNMPv1/v2c community name string. Duplicate community names are not allowed in this table. Note that a null string is not a valid community name. Attempting to set this object to a null string or to a duplicate value results in the agent returning a 'badValue' error for SNMPv1 or 'inconsistentValue' error for SNMPv2c/v3.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..20)

snmpTrapSNMPVersion		1.3.6.1.4.1.3646.1300.2.1.6.1.1.3
This object indicates the version of SNMPv1 or SNMPv2c.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	snmpv1(1), snmpv2c(2)

snmpTrapRowStatus		1.3.6.1.4.1.3646.1300.2.1.6.1.1.4
This object indicates the status of SNMP trap.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

snmpCommunityMib		1.3.6.1.4.1.3646.1300.2.1.7
OBJECT IDENTIFIER

snmpCommunityTable		1.3.6.1.4.1.3646.1300.2.1.7.1
A table of SNMPv1/v2c community string to SNMPv3 view name mappings.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SnmpCommunityEntry

snmpCommunityEntry		1.3.6.1.4.1.3646.1300.2.1.7.1.1
An entry containing objects about SNMP community at this systemp.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpCommunityEntry

snmpCommunityName		1.3.6.1.4.1.3646.1300.2.1.7.1.1.1
The SNMPv1/v2c community name string. Duplicate community names are not allowed in this table. Note that a null string is not a valid community name. Attempting to set this object to a null string or to a duplicate value results in the agent returning a 'badValue' error for SNMPv1 or 'inconsistentValue' error for SNMPv2c/v3.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..20)

snmpCommunityPermission		1.3.6.1.4.1.3646.1300.2.1.7.1.1.2
This object specifies the type of access allowed. 'readOnly(1)' allows GET operations (i.e., GET, GET-NEXT, GET-BULK) and 'readWrite(2)' allows both GET and SET operations.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	readOnly(1), readWrite(2)

snmpCommunityRowStatus		1.3.6.1.4.1.3646.1300.2.1.7.1.1.3
This object indicates the status of this entry. A row in this table can be created using the 'createAndGo(4)' (if all objects without default values are supplied with valid values in a single SNMP PDU) or the 'createAndWait(5)' action states. Until all parameters are valid for a conceptual row, this object is 'notReady(3)'. All parameters must be valid before this object can be set to 'active(1)'. Any object in a conceptual row can be modified independent of the value of this object (that is, can be changed while 'active(1)', notInService(2) or 'notReady(3)').
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

askeyDslamFdbTable		1.3.6.1.4.1.3646.1300.2.1.9
A table that contains information about unicast entries for which the IP-DSLAM has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AskeyDslamFdbEntry

askeyDslamFdbEntry		1.3.6.1.4.1.3646.1300.2.1.9.1
Information about a specific unicast MAC address on a specific line for which the IP-DSLAM has some forwarding and/or filtering information.
Status: current	Access: not-accessible
OBJECT-TYPE
	AskeyDslamFdbEntry

fdbMacIndex		1.3.6.1.4.1.3646.1300.2.1.9.1.1
A simple index into 'askeyDslamFdbTable'.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..8

fdbVpi		1.3.6.1.4.1.3646.1300.2.1.9.1.2
The VPI value of the VCL. The maximum VPI value cannot exceed the value allowable by the atmInterfaceMaxVpiBits.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

fdbVci		1.3.6.1.4.1.3646.1300.2.1.9.1.3
The VCI value of the VCL. The maximum VCI value cannot exceed the value allowable by the atmInterfaceMaxVciBits.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

macAddress		1.3.6.1.4.1.3646.1300.2.1.9.1.4
A unicast MAC address for which the bridge has forwarding and/or filtering information.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

askeyDslamFdbStatus		1.3.6.1.4.1.3646.1300.2.1.9.1.5
The status of this entry. The meanings of the values are: learned_unique(1): the value of the corresponding instance of macAddress was learned, and is being used. It indicates that the macAddress is an unique one and there is no duplicated (spoofed) one detected in the IP-DSLAM. learned_spoofed_active(2) : the value of the corresponding instance of macAddress was learned, and is being used. It indicates that there is an duplicated (spoofed) one detected in theIP-DSLAM. learned_spoofed_inactive(3) : the value of the corresponding instance of macAddress was learned, and is NOT being used. It indicates that there is an duplicated(spoofed) one detected in the IP-DSLAM. mgmt_forbid(4): the value of the corresponding instance of macAddress was set by the operator. It indicates that an Ethernet frame of srcMac='macAddress' is to be dropped by the IP-DSLAM. mgmt_permit(5): the value of the corresponding instance of macAddress was set by the operator. It indicates that an Ethernet frame of srcMac='macAddress' is to be forwarded by the IP-DSLAM. learned_routed(6): the value of the corresponding instance of macAddress was learned, and is being used. It indicates that the macAddress is added by the IP-DSLAM.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	learned-unique(1), learned-spoofed-active(2), learned-spoofed-inactive(3), mgmt-forbid(4), mgmt-permit(5), learned-routed(6)

configDataMib		1.3.6.1.4.1.3646.1300.2.1.10
save(1): save the current configuration data to NVRAM(flash) as the main configuration data. restore(2): replace the main configuration data with the backup configuration data.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	save(1), restore(2)

askeyCardInfoTable		1.3.6.1.4.1.3646.1300.2.1.11
This table is information about card/slot on ASKEY IPDSLAM.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AskeyCardInfoEntry

askeyCardInfoEntry		1.3.6.1.4.1.3646.1300.2.1.11.1
An entry about information of the card/slot.
Status: current	Access: not-accessible
OBJECT-TYPE
	AskeyCardInfoEntry

askeyCardPlannedType		1.3.6.1.4.1.3646.1300.2.1.11.1.1
Supposed type of this card.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

askeyCardType		1.3.6.1.4.1.3646.1300.2.1.11.1.2
Current working type of this card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

askeyCardHWVersion		1.3.6.1.4.1.3646.1300.2.1.11.1.3
The Hardware version of this card.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

askeyCardSWVersion		1.3.6.1.4.1.3646.1300.2.1.11.1.4
The Software version of this card.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

askeyCardImage		1.3.6.1.4.1.3646.1300.2.1.11.1.5
Description for the location of the image.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

askeyCardUptime		1.3.6.1.4.1.3646.1300.2.1.11.1.6
The uptime (in seconds) of this card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

askeyCardRole		1.3.6.1.4.1.3646.1300.2.1.11.1.7
This object descibes the card role.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), standby(2)

askeyCardSerialNumber		1.3.6.1.4.1.3646.1300.2.1.11.1.8
The card serial number which is an unique number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..40)

askeyCardAdminStatus		1.3.6.1.4.1.3646.1300.2.1.11.1.9
The operation of this card. Only value is 'reset(1)' will reset this card.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

askeyCardOperStatus		1.3.6.1.4.1.3646.1300.2.1.11.1.10
This object indicates the card's operational status. The notPresent(3) status indicates the card is physically removed (note this may or may not be possible depending on the type of card.) The operational(1) status indicates that the card is enabled (see rptrPortAdminStatus) and working, even though it might be auto-partitioned (see rptrPortAutoPartitionState). If this object has the value operational(1) and cwmAdminStatus is set to disabled(2), it is expected that this object's value will soon change to notOperational(2).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	operational(1), notOperational(2), notPresent(3)

lineCardAdminVlanTagPassEnabled		1.3.6.1.4.1.3646.1300.2.1.11.1.11
Enable(1) or disable VLAN tag pass through function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

lineCardOperVlanTagPassEnabled		1.3.6.1.4.1.3646.1300.2.1.11.1.12
Current status of VLAN tag passes through funtion.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), enabled(1), disabled(2)

lineCardAdminRfc2684Encap		1.3.6.1.4.1.3646.1300.2.1.11.1.13
Setting this object to LLC (1) to encapsulate the packet to LLC style. Setting it to vcMux (2) to encapsulate the packet to VC-MUX style.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(0), llc(1), vcMux(2)

lineCardOperRfc2684Encap		1.3.6.1.4.1.3646.1300.2.1.11.1.14
Current applied rfc2684 encapsulation method.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), llc(1), vcMux(2)

lineCardServiceTypeControl		1.3.6.1.4.1.3646.1300.2.1.11.1.15
Set or get applied control of service type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(0), enabled(1), disabled(2)

shdslFirmwareUpgrade		1.3.6.1.4.1.3646.1300.2.1.11.1.16
Upgrade SHDSL line card firmware.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	upgrade(0)

shdslFirmwareUpgradeState		1.3.6.1.4.1.3646.1300.2.1.11.1.17
SHDSL line card firmware pgrade state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), inital(1), transmission(2), burning(3), finished(4), failedToBurn(5), driverError(6), noFirmwareImage(7), failedToTransmitImage(8)

taggedModeAdminStatus		1.3.6.1.4.1.3646.1300.2.1.11.1.18
Card administrative tagged mode. This entry indicates tagged mode configured on the specific card.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tagged-only(1), untagged-only(2)

taggedModeOperStatus		1.3.6.1.4.1.3646.1300.2.1.11.1.19
Card operational tagged mode. This entry indicates tagged mode running on the specific card. All ports of the tagged type card will drop packets that don't have tagged header. And all ports of untagged type card will drop packets that have tagged header. Do nothing for 'noAction' case.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	tagged-only(1), untagged-only(2)

linePortInfo		1.3.6.1.4.1.3646.1300.2.1.12
OBJECT IDENTIFIER

linePortInfoTable		1.3.6.1.4.1.3646.1300.2.1.12.1
A list of line port information entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LinePortInfoEntry

linePortInfoEntry		1.3.6.1.4.1.3646.1300.2.1.12.1.1
An information entry containing objects for each line port.
Status: current	Access: not-accessible
OBJECT-TYPE
	LinePortInfoEntry

linePortAdminStatus		1.3.6.1.4.1.3646.1300.2.1.12.1.1.1
The desired state of the line port. The enable(1) state ready to pass packets. The disable(2) state stop passing any packets. The testing(3) state indicates that no operational packets can be passed, it is for debug only. Finally, reset(4) state will reset this line port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2), testing(3), reset(4)

linePortOperStatus		1.3.6.1.4.1.3646.1300.2.1.12.1.1.2
This object indicates the line port's operational status. The notPresent(3) status indicates the line port is physically removed (note this may or may not be possible depending on the type of port). The operational(1) status indicates that the port is enabled (see rptrPortAdminStatus) and working, even though it might be auto-partitioned (see rptrPortAutoPartitionState). If this object has the value operational(1) and rptrPortAdminStatus is set to disabled(2), it is expected that this object's value will soon change to notOperational(2).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	operational(1), notOperational(2), notPresent(3)

circuitID		1.3.6.1.4.1.3646.1300.2.1.12.1.1.3
The identity for this circuit. The value is 'shelf.slot.port'.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

remoteID		1.3.6.1.4.1.3646.1300.2.1.12.1.1.4
The string is sent transparently to authorization service.
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString	Size(0..63)

dot1TpMACAging		1.3.6.1.4.1.3646.1300.2.1.13
This object decides MAC enrties aged out or not. aged: MAC entries will be aged out nonaged: MAC entries will never be aged out
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aged(1), nonaged(2)

askeyRebootSystemAction		1.3.6.1.4.1.3646.1300.2.1.14
Reboot the system.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reboot(1)

askeyDslamOam		1.3.6.1.4.1.3646.1300.2.1.15
OBJECT IDENTIFIER

oamF5		1.3.6.1.4.1.3646.1300.2.1.15.1
OBJECT IDENTIFIER

oamF5IfIndex		1.3.6.1.4.1.3646.1300.2.1.15.1.1
The ifIndex of the line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

oamF5Vpi		1.3.6.1.4.1.3646.1300.2.1.15.1.2
The VPI value of the VCL. The maximum VPI value cannot exceed the value allowable by the atmInterfaceMaxVpiBits.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

oamF5Vci		1.3.6.1.4.1.3646.1300.2.1.15.1.3
The VCI value of the VCL. The maximum VCI value cannot exceed the value allowable by the atmInterfaceMaxVciBits.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

oamF5Scope		1.3.6.1.4.1.3646.1300.2.1.15.1.4
The scope of the OAM F5 loopback cell. Set this object will trigger OAM processing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	end-to-end(1), segment-to-segment(2), both-end2end-segment2segment(3)

askeySystemManagementInfo		1.3.6.1.4.1.3646.1300.2.1.16
OBJECT IDENTIFIER

askeyEmsVlanId		1.3.6.1.4.1.3646.1300.2.1.16.1
In-band management VLAN ID.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4094

askeyBootDevice		1.3.6.1.4.1.3646.1300.2.1.16.2
OBJECT IDENTIFIER

askeyNextBootDevice		1.3.6.1.4.1.3646.1300.2.1.16.2.1
Configure the next boot partition.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	opCodeA(1), opCodeB(2)

askeyCurrentBootDevice		1.3.6.1.4.1.3646.1300.2.1.16.2.2
Show current the boot partition.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	network(0), opCodeA(1), opCodeB(2)

askeySystemManagementIgmp		1.3.6.1.4.1.3646.1300.2.1.16.3
Configure the IGMP proxy and IGMP snoop.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enableIgmpsnoop(1), enableIgmpproxy(2), disableIgmp(3)

askeyRedundancy		1.3.6.1.4.1.3646.1300.2.1.16.4
OBJECT IDENTIFIER

askeyRedundancyAutoSyncEnabled		1.3.6.1.4.1.3646.1300.2.1.16.4.1
The Askey IPDSLAM can auto synchronize standby NC configuration with active NC. This object enables or disables such synchronization.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

askeyRedundancyAutoSyncPeriod		1.3.6.1.4.1.3646.1300.2.1.16.4.2
Auto synchronization period. The value unit is in second.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	30..3600

askeyRedundancySync		1.3.6.1.4.1.3646.1300.2.1.16.4.3
Synchronize redundancy immediately.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	syncNow(1)

askeySystemManagementInfoVlan		1.3.6.1.4.1.3646.1300.2.1.16.5
OBJECT IDENTIFIER

askeySystemManagementInfoVlanMacLimitTable		1.3.6.1.4.1.3646.1300.2.1.16.5.1
A table that contains information about the MAC limit per VLAN ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AskeySystemManagementInfoVlanMacLimitEntry

askeySystemManagementInfoVlanMacLimitEntry		1.3.6.1.4.1.3646.1300.2.1.16.5.1.1
Information about the MAC limit per VLAN.
Status: current	Access: not-accessible
OBJECT-TYPE
	AskeySystemManagementInfoVlanMacLimitEntry

askeySystemManagementInfoVlanID		1.3.6.1.4.1.3646.1300.2.1.16.5.1.1.1
The ID of target VLAN which MAC limits.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..4094

askeySystemManagementInfoVlanMacLimit		1.3.6.1.4.1.3646.1300.2.1.16.5.1.1.2
MAC limit on specific VLAN. Default values are 5376 for AM0021 and 1568 for AM0031.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..50000

askeySystemManagementInfoVlanMacLimitEnabled		1.3.6.1.4.1.3646.1300.2.1.16.5.1.1.3
Enable or disable MAC limit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(0), enabled(1), disabled(2)

askeyCosQueue		1.3.6.1.4.1.3646.1300.2.1.18
OBJECT IDENTIFIER

askeyCosQueueMappingTable		1.3.6.1.4.1.3646.1300.2.1.18.1
A table that contains information about COS queues mapping with 802.1p.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AskeyCosQueueMappingEntry

askeyCosQueueMappingEntry		1.3.6.1.4.1.3646.1300.2.1.18.1.1
Information about COS queue mapping.
Status: current	Access: not-accessible
OBJECT-TYPE
	AskeyCosQueueMappingEntry

askeyCosQueueMapping8021p		1.3.6.1.4.1.3646.1300.2.1.18.1.1.1
The identity of the specific 802.1p priority mapping.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..7

askeyCosQueueIndex		1.3.6.1.4.1.3646.1300.2.1.18.1.1.2
The index of COS queue.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..8

askeySystemUserAccountTable		1.3.6.1.4.1.3646.1300.2.1.19
This table contains information of system user account. One entry in this table reflects a user information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AskeySystemUserAccountEntry

askeySystemUserAccountEntry		1.3.6.1.4.1.3646.1300.2.1.19.1
An entry reflects a user information.
Status: current	Access: not-accessible
OBJECT-TYPE
	AskeySystemUserAccountEntry

askeySystemUserAccountUserName		1.3.6.1.4.1.3646.1300.2.1.19.1.1
The name of account user.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..16)

askeySystemUserAccountPassword		1.3.6.1.4.1.3646.1300.2.1.19.1.2
The password of account user.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..16)

askeySystemUserAccountGroup		1.3.6.1.4.1.3646.1300.2.1.19.1.3
The group which account belongs to.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	guest(1), admin(2)

askeySystemUserAccountRowStatus		1.3.6.1.4.1.3646.1300.2.1.19.1.4
This object controls creation/deletion of the associated entry in this table as per the semantics of RowStatus.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

askeyPPPoE		1.3.6.1.4.1.3646.1300.2.1.20
OBJECT IDENTIFIER

suboption		1.3.6.1.4.1.3646.1300.2.1.20.1
Enable or disable PPPoE suboption. The circuit information recorded on 'linePortInfo' table will be transferred to authorization service, for example, a radius server, if this function enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

dnsService		1.3.6.1.4.1.3646.1300.2.1.21
OBJECT IDENTIFIER

dnsServer1IPAddress		1.3.6.1.4.1.3646.1300.2.1.21.1
The IP address of DNS server. This server is used first priority.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dnsServer2IPAddress		1.3.6.1.4.1.3646.1300.2.1.21.2
The IP address of DNS server. This server is used second priority.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dnsServer3IPAddress		1.3.6.1.4.1.3646.1300.2.1.21.3
The IP address of DNS server. This server is used lowest priority.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

timeService		1.3.6.1.4.1.3646.1300.2.1.22
OBJECT IDENTIFIER

protocol		1.3.6.1.4.1.3646.1300.2.1.22.1
The time service is used which protocol.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), sntp(1)

updatePeriod		1.3.6.1.4.1.3646.1300.2.1.22.2
Synchronize time which system update time by time servers. This object unit is in minute.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..1440

timeServer1InetAddress		1.3.6.1.4.1.3646.1300.2.1.22.3
The address of time server1. This server is used first priority.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress	Size(0..63)

timeServer2InetAddress		1.3.6.1.4.1.3646.1300.2.1.22.4
The address of time server2. This server is used second priority.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress	Size(0..63)

timeServer3InetAddress		1.3.6.1.4.1.3646.1300.2.1.22.5
The address of time server3. This server is used lowest priority.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress	Size(0..63)

timeServer1Status		1.3.6.1.4.1.3646.1300.2.1.22.6
server1 current status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSet(0), networkTimeSource(1), backupMode(2), failToResolveDomainName(3), serverNoResponse(4)

timeServer2Status		1.3.6.1.4.1.3646.1300.2.1.22.7
server2 current status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSet(0), networkTimeSource(1), backupMode(2), failToResolveDomainName(3), serverNoResponse(4)

timeServer3Status		1.3.6.1.4.1.3646.1300.2.1.22.8
server3 current status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSet(0), networkTimeSource(1), backupMode(2), failToResolveDomainName(3), serverNoResponse(4)

timeZone		1.3.6.1.4.1.3646.1300.2.1.22.9
The system time zone.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	-12..13

ugeMIBObjects		1.3.6.1.4.1.3646.1300.2.1.23
OBJECT IDENTIFIER

ugeAutoNegotiationTable		1.3.6.1.4.1.3646.1300.2.1.23.2
The table indicates UGE auto negotiation states.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UgeAutoNegotionEntry

ugeAutoNegotionEntry		1.3.6.1.4.1.3646.1300.2.1.23.2.1
An entry indicates UGE auto negotiation states.
Status: current	Access: not-accessible
OBJECT-TYPE
	UgeAutoNegotionEntry

autoNegotiationState		1.3.6.1.4.1.3646.1300.2.1.23.2.1.1
Enable or disable UGE port auto negotiation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

ugePauseFrameStatisticTable		1.3.6.1.4.1.3646.1300.2.1.23.3
The table indicates UGE pause packet statistic.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UgePauseFrameStatisticEntry

ugePauseFrameStatisticEntry		1.3.6.1.4.1.3646.1300.2.1.23.3.1
An entry indicates UGE pause packet statistic.
Status: current	Access: not-accessible
OBJECT-TYPE
	UgePauseFrameStatisticEntry

rxPausePackets		1.3.6.1.4.1.3646.1300.2.1.23.3.1.1
The counter indicates pause packets received from this UGE.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

txPausePackets		1.3.6.1.4.1.3646.1300.2.1.23.3.1.2
The counter indicates pause packets transmitted by this UGE.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

subtendVLANTable		1.3.6.1.4.1.3646.1300.2.1.23.4
The table indicates which VLAN packets can pass through subtending ports.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SubtendVLANEntry

subtendVLANEntry		1.3.6.1.4.1.3646.1300.2.1.23.4.1
An entry for subtendVLANTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SubtendVLANEntry

subtendState		1.3.6.1.4.1.3646.1300.2.1.23.4.1.1
Enable or disable NC VLAN subtend.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

subtendVLAN		1.3.6.1.4.1.3646.1300.2.1.23.4.1.2
Specify what VLAN can pass through by subtending port.
Status: current	Access: read-write
OBJECT-TYPE
	VLANList

ugeVLANTable		1.3.6.1.4.1.3646.1300.2.1.23.5
This table indicates relation between UGEs and packets with specific VLAN tags. Only packets with tag values can been send out from UGEs, otherwise will not.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UgeVLANEntry

ugeVLANEntry		1.3.6.1.4.1.3646.1300.2.1.23.5.1
An entry for ugeVLANTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	UgeVLANEntry

ugeVLAN		1.3.6.1.4.1.3646.1300.2.1.23.5.1.1
Specify what VLAN can pass through by UGE port.
Status: current	Access: read-only
OBJECT-TYPE
	VLANList

securedHosts		1.3.6.1.4.1.3646.1300.2.1.24
OBJECT IDENTIFIER

securedHostAdminStatus		1.3.6.1.4.1.3646.1300.2.1.24.1
Enable or disable secured host function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

securedHostTable		1.3.6.1.4.1.3646.1300.2.1.24.2
This table provides the information of the secured hosts which may access managed system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SecuredHostEntry

securedHostEntry		1.3.6.1.4.1.3646.1300.2.1.24.2.1
An entry to information of the secured hosts which may access managed system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SecuredHostEntry

securedIPSectorIndex		1.3.6.1.4.1.3646.1300.2.1.24.2.1.1
An IP sector index.
Status: current	Access: not-accessible
OBJECT-TYPE
	IPSectionIndex

securedIPSectorStartIP		1.3.6.1.4.1.3646.1300.2.1.24.2.1.2
An IP address expresses IP sector starting.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

securedIPSectorEndIP		1.3.6.1.4.1.3646.1300.2.1.24.2.1.3
An IP address expresses IP sector ending.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

allowedServiceType		1.3.6.1.4.1.3646.1300.2.1.24.2.1.4
Contains indicates whether access mode is enabled or disabled. This is a bit-map of possible settings.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	snmp(0), telnet(1), ftp(2), tftp(3)

netBIOSFilter		1.3.6.1.4.1.3646.1300.2.1.25
OBJECT IDENTIFIER

netBIOSFilterAction		1.3.6.1.4.1.3646.1300.2.1.25.1
Drop or forward NetBIOS/NetBEUI packets.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dropping(1), forwarding(2)