AT-DS3-MIB
File:
AT-DS3-MIB.mib (4494 bytes)
Imported modules
Imported symbols
Defined Types
Ds3TrapEntry |
|
SEQUENCE |
|
|
|
|
ds3TcaTrapEnable |
INTEGER |
|
|
ds3TrapError |
INTEGER |
|
|
ds3TrapLoc |
INTEGER |
|
|
ds3TrapInterval |
INTEGER |
|
Defined Values
ds3 |
1.3.6.1.4.1.207.8.4.4.4.109 |
This MIB file contains definitions of managed objects for the
DS3 module. |
MODULE-IDENTITY |
|
|
|
ds3TrapTable |
1.3.6.1.4.1.207.8.4.4.4.109.1 |
The ATR enterprise DS3 trap table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
Ds3TrapEntry |
|
ds3TrapEntry |
1.3.6.1.4.1.207.8.4.4.4.109.1.1 |
An entry in the ATR enterprise DS3 trap table. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Ds3TrapEntry |
|
|
ds3TcaTrapEnable |
1.3.6.1.4.1.207.8.4.4.4.109.1.1.1 |
Indicates whether the threshold crossing alert traps
should be generated for this interface. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enabled(1), disabled(2) |
|
ds3TrapError |
1.3.6.1.4.1.207.8.4.4.4.109.1.1.2 |
This variable shows which kind of parameter or primitive caused
the trap. This variable is really just a placeholder for the
object sent in the DS3 TRAP, but can be read independently if
required. The variable will hold the value at the latest trap.
A value of ds3NoError shows no trap has occured |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
ds3NoError(1), ds3PES(2), ds3PSES(3), ds3SEFs(4), ds3UAS(5), ds3LCVs(6), ds3PCVs(7), ds3LESs(8), ds3CCVs(9), ds3CESs(10), ds3CSESs(11) |
|
ds3TrapLoc |
1.3.6.1.4.1.207.8.4.4.4.109.1.1.3 |
This variable shows whether the trap was caused by a problem at the local or
remote end. This variable is really just a placeholder for the
object sent in the DS3 TRAP, but can be read independently if
required. The variable will hold the value at the latest trap.
A value of ds3NoLoc shows no trap had occured. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
ds3NoLoc(1), ds3Near(2), ds3Far(3) |
|
ds3TrapInterval |
1.3.6.1.4.1.207.8.4.4.4.109.1.1.4 |
This variable shows whether the counter which has crossed the
threshold is a twenty four hour or fifteen minute counter.
This variable is really just a placeholder for the
object sent in the DS3 TRAP, but can be read independently if
required. The variable will hold the value at the latest trap.
A value of ds3NoInt shows no trap has occured. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
ds3NoInt(1), ds3Fifteen(2), ds3Twentyfour(3) |
|
ds3Traps |
1.3.6.1.4.1.207.8.4.4.4.109.0 |
OBJECT IDENTIFIER |
|
|
|
tcaTrap |
1.3.6.1.4.1.207.8.4.4.4.109.0.1 |
A DS3 trap is generated when a threshold crossing alert
occurs. This happens when an error count exceeds a pre
determined value. The values are counted over 15 minute and
24 hour periods. Once a trap has occured in a given period
it may not occur again within the same period. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|