ATMEDGE-MIB

File: ATMEDGE-MIB.mib (16257 bytes)

Imported modules

RFC-1212 RFC1213-MIB GEN-MIB

Imported symbols

OBJECT-TYPE DisplayString lannet

Defined Types

AtmEdgePortEntry  
SEQUENCE    
  atmEdgePortGroupId INTEGER
  atmEdgePortId INTEGER
  atmEdgePortHealthStatus INTEGER
  atmEdgePortMACAddr OCTET STRING
  atmEdgePortATMAddr OCTET STRING
  atmEdgePortLanType INTEGER
  atmEdgePortILMIStatus INTEGER
  atmEdgePortSignalStatus INTEGER
  atmEdgePortActualUNIVersion INTEGER
  atmEdgePortNetworkPrefix OCTET STRING
  atmEdgePortDormantHealthStatus INTEGER
  atmEdgePortRedundancyStatus INTEGER

AtmEdgeGroupEntry  
SEQUENCE    
  atmEdgeGroupGroupId INTEGER
  atmEdgeGroupWorkState INTEGER
  atmEdgeGroupBITResult INTEGER

AssociationEntry  
SEQUENCE    
  associationSlotIndex INTEGER
  associationPortIndex INTEGER
  associationIndex INTEGER
  associationVlan INTEGER
  associationElan DisplayString
  associationRowStatus INTEGER
  associationIfIndex INTEGER

GenCTIGroupEntry  
SEQUENCE    
  genCTIGroupId INTEGER
  genCTIGroupCellLossAlarm INTEGER
  genCTIGroupRedunAvailable INTEGER
  genCTIGroupRedunFlip INTEGER
  genCTIGroupFiberActive INTEGER
  genCTIGroupVmuxMaster INTEGER

GenCTIPortEntry  
SEQUENCE    
  genCTIPortGroupId INTEGER
  genCTIPortId INTEGER
  genCTIPortSync INTEGER
  genCTIPortRxAlarm INTEGER
  genCTIPortTxAlarm INTEGER

Defined Values

atmEdge 1.3.6.1.4.1.81.26
OBJECT IDENTIFIER    

cti 1.3.6.1.4.1.81.29
OBJECT IDENTIFIER    

atmEdgePort 1.3.6.1.4.1.81.26.1
OBJECT IDENTIFIER    

atmEdgePortTable 1.3.6.1.4.1.81.26.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmEdgePortEntry

atmEdgePortEntry 1.3.6.1.4.1.81.26.1.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AtmEdgePortEntry  

atmEdgePortGroupId 1.3.6.1.4.1.81.26.1.1.1.1
Id of the slot to which the atm port belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

atmEdgePortId 1.3.6.1.4.1.81.26.1.1.1.2
Id of the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

atmEdgePortHealthStatus 1.3.6.1.4.1.81.26.1.1.1.3
Indicates the health state of the port. When this field indicates carrierFailure, it means that there is no carrier: the agent should send a trap of type fault.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), atmError(2), sonetLinkError(3), sonetRemoteLinkError(4), notSupported(255)  

atmEdgePortMACAddr 1.3.6.1.4.1.81.26.1.1.1.4
MAC address of the ATM port. If the port has no MAC address, this value should be zero length octet string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..6)  

atmEdgePortATMAddr 1.3.6.1.4.1.81.26.1.1.1.5
ATM address of the ATM port. If the port has no ATM address, this value should be zero length octet string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..20)  

atmEdgePortLanType 1.3.6.1.4.1.81.26.1.1.1.6
The type of the up link port. This is used do find whether the port wants to receive the association table and from what kind. ethernet - an Ethernet Edge device. token-ring - a Token Ring Edge device. notSupported means that currently the device doesn't currently act as an Edge Devices
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ethernet(1), token-ring(2), notSupported(255)  

atmEdgePortILMIStatus 1.3.6.1.4.1.81.26.1.1.1.7
The current state of the ILMI signalling of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), notsupported(255)  

atmEdgePortSignalStatus 1.3.6.1.4.1.81.26.1.1.1.8
The current state of the ATM signalling for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), notsupported(255)  

atmEdgePortActualUNIVersion 1.3.6.1.4.1.81.26.1.1.1.9
The type of signalling that is currently being used on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), uni-30(2), uni-31(3), uni-40(4), notsupported(255)  

atmEdgePortNetworkPrefix 1.3.6.1.4.1.81.26.1.1.1.10
The prefix of the ATM switch connected to this ATM port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(13)  

atmEdgePortDormantHealthStatus 1.3.6.1.4.1.81.26.1.1.1.11
Indicates the health state of the Dormant port. When this field indicates carrierFailure, it means that there is no carrier: the agent should send a trap of type fault.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), atmError(2), sonetLinkError(3), sonetRemoteLinkError(4), notSupported(255)  

atmEdgePortRedundancyStatus 1.3.6.1.4.1.81.26.1.1.1.12
This item is relevant for ports which includes redundant links. This item indicates which of the links is active. Default value=masterNicActive(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER masterNicActive(1), secondaryNicActive(2), notSupported(255)  

atmEdgeGroup 1.3.6.1.4.1.81.26.2
OBJECT IDENTIFIER    

atmEdgeGroupTable 1.3.6.1.4.1.81.26.2.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmEdgeGroupEntry

atmEdgeGroupEntry 1.3.6.1.4.1.81.26.2.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AtmEdgeGroupEntry  

atmEdgeGroupGroupId 1.3.6.1.4.1.81.26.2.1.1.1
Slot number in which the module is located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atmEdgeGroupWorkState 1.3.6.1.4.1.81.26.2.1.1.2
One of the possible states of the module: this item indicates if the module is runing or booting. The value runAndBoot(3) indicates a serious software problem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER run(1), boot(2), runAndBoot(3), none(4), notSupported(255)  

atmEdgeGroupBITResult 1.3.6.1.4.1.81.26.2.1.1.3
The Bit Indication Test in state faulty indicates a problem. The agent should send a fault trap in this case.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), faulty(2), notSupported(255)  

atmEdgeAssociation 1.3.6.1.4.1.81.26.3
OBJECT IDENTIFIER    

associationTable 1.3.6.1.4.1.81.26.3.1
This table contains all the information concerning the association between VLAN and ELAN names.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AssociationEntry

associationEntry 1.3.6.1.4.1.81.26.3.1.1
An entry in the table, contains information about a VLAN associated to an ELAN on a particular up link port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AssociationEntry  

associationSlotIndex 1.3.6.1.4.1.81.26.3.1.1.1
Index which identifies the Slot inside the chassis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

associationPortIndex 1.3.6.1.4.1.81.26.3.1.1.2
Index which identifies the Port inside the Slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

associationIndex 1.3.6.1.4.1.81.26.3.1.1.3
An arbitrary integer which uniquely identifies an association number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

associationVlan 1.3.6.1.4.1.81.26.3.1.1.4
The VLAN number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

associationElan 1.3.6.1.4.1.81.26.3.1.1.5
The ELAN name. For Ethernet devices the default is default. For Token Ring devices the default is defaultTrn
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

associationRowStatus 1.3.6.1.4.1.81.26.3.1.1.6
The status of the entry, not a standard RowStatus. To create an entry, the console finds the next available entry. It changes the entry to 'notReady', it fills the VLAN number and the ELAN name, and it changes the entry to 'createAndGo'. The device creates the interface and the LEC, when it finishes, it changes the entry to 'active'. To delete an entry, the console changes the entry to 'destroy'. To disable an entry, the console changes the entry to 'notInService'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6)  

associationIfIndex 1.3.6.1.4.1.81.26.3.1.1.7
Creating a row in this table causes the agent to add one row in the interface table. Before setting the row status to active, the agent fills this field with the value of the ifIndex of the new created row.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genCTIGroup 1.3.6.1.4.1.81.29.1
OBJECT IDENTIFIER    

genCTIGroupTable 1.3.6.1.4.1.81.29.1.1
Attributes pertaining to the CTI module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenCTIGroupEntry

genCTIGroupEntry 1.3.6.1.4.1.81.29.1.1.1
An entry in the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenCTIGroupEntry  

genCTIGroupId 1.3.6.1.4.1.81.29.1.1.1.1
Slot number in which the module is located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genCTIGroupCellLossAlarm 1.3.6.1.4.1.81.29.1.1.1.2
Indicates a condition of significant cell loss which results in performance degradation
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), cellLossAlarm(2)  

genCTIGroupRedunAvailable 1.3.6.1.4.1.81.29.1.1.1.3
Indication on the availability of external redundancy unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noRedun(1), redunAvailable(2)  

genCTIGroupRedunFlip 1.3.6.1.4.1.81.29.1.1.1.4
In regular conditions this item is in the noFlip state. Changing the item value to flipFiber will result in flipping to the other link. After this flip is completed the value will return back to the noFlip sate. this item is relevant only when a redundant link is available
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noFlip(1), flipFiber(2)  

genCTIGroupFiberActive 1.3.6.1.4.1.81.29.1.1.1.5
When there is an external fiber redundancy this item shows which of the links is active
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER fiberActiveA(1), fiberActiveB(2)  

genCTIGroupVmuxMaster 1.3.6.1.4.1.81.29.1.1.1.6
On the poit to point voice connection via the FIM port one side is a master and the other side is a slave. This item shows whether the local module is master or slave
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER localMaster(1), localSlave(2)  

genCTIPortTable 1.3.6.1.4.1.81.29.1.2
Table of ports in a CTI module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenCTIPortEntry

genCTIPortEntry 1.3.6.1.4.1.81.29.1.2.1
Entry in the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenCTIPortEntry  

genCTIPortGroupId 1.3.6.1.4.1.81.29.1.2.1.1
Slot number in which the module is located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genCTIPortId 1.3.6.1.4.1.81.29.1.2.1.2
The port index. The numbering scheme for the CTI ports follows: 1 - FIM Voice port 2 - UTP ATM Port 3 - SONET port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genCTIPortSync 1.3.6.1.4.1.81.29.1.2.1.3
Sync status for the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), noSync(2), notSupported(255)  

genCTIPortRxAlarm 1.3.6.1.4.1.81.29.1.2.1.4
Rx Alarm status for the port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), rxAlarm(2), notSupported(255)  

genCTIPortTxAlarm 1.3.6.1.4.1.81.29.1.2.1.5
Tx Alarm status for the port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), txAlarm(2), notSupported(255)