AUTH-MIB

File: AUTH-MIB.mib (91740 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMP-FRAMEWORK-MIB
RFC1155-SMI RFC1213-MIB IF-MIB
IEEE8021-PAE-MIB DLINK-ID-REC-MIB INET-ADDRESS-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
Unsigned32 Counter32 Counter64
TimeTicks TruthValue RowStatus
MacAddress SnmpAdminString IpAddress
DisplayString InterfaceIndex PaeControlledPortStatus
dot1xPaePortNumber dlink-common-mgmt InetAddressType
InetAddress

Defined Types

PortList  
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
TEXTUAL-CONVENTION    
  OCTET STRING  

VlanId  
A 12-bit VLAN ID used in the VLAN Tag header.
TEXTUAL-CONVENTION    
  INTEGER 1..4094  

RadiusServerEntry  
SEQUENCE    
  swRadiusServerIndex INTEGER
  swRadiusServerIpAddr IpAddress
  swRadiusServerKey OCTET STRING
  swRadiusAuthPortNumber Unsigned32
  swRadiusAcctPortNumber Unsigned32
  swRadiusServerStatus RowStatus
  swRadiusServerTimeout Unsigned32
  swRadiusServerRetransmit Unsigned32
  swRadiusServerAddrType InetAddressType
  swRadiusServerAddr InetAddress

RadiusAuthServerEntry  
SEQUENCE    
  swRadiusAuthServerIndex Integer32
  swRadiusAuthServerAddress IpAddress
  swRadiusAuthClientServerPortNumber Unsigned32
  swRadiusAuthClientRoundTripTime Counter32
  swRadiusAuthClientAccessRequests Counter32
  swRadiusAuthClientAccessRetransmissions Counter32
  swRadiusAuthClientAccessAccepts Counter32
  swRadiusAuthClientAccessRejects Counter32
  swRadiusAuthClientAccessChallenges Counter32
  swRadiusAuthClientMalformedAccessResponses Counter32
  swRadiusAuthClientBadAuthenticators Counter32
  swRadiusAuthClientPendingRequests Counter32
  swRadiusAuthClientTimeouts Counter32
  swRadiusAuthClientUnknownTypes Counter32
  swRadiusAuthClientPacketsDropped Counter32

AcctServiceEntry  
SEQUENCE    
  swRadiusAcctServiceIndex INTEGER
  swRadiusAcctServiceMethod INTEGER
  swRadiusAcctServiceMode INTEGER

SwMacAuthStateEntry  
SEQUENCE    
  swPaeMacAddr MacAddress
  swPaePortNumber InterfaceIndex
  swAuthPaeState INTEGER
  swAuthBackendAuthState INTEGER
  swAuthAuthControlledPortStatus PaeControlledPortStatus

SwMacAuthStatsEntry  
SEQUENCE    
  swAuthEapolFramesRx Counter32
  swAuthEapolFramesTx Counter32
  swAuthEapolStartFramesRx Counter32
  swAuthEapolLogoffFramesRx Counter32
  swAuthEapolRespIdFramesRx Counter32
  swAuthEapolRespFramesRx Counter32
  swAuthEapolReqIdFramesTx Counter32
  swAuthEapolReqFramesTx Counter32
  swAuthInvalidEapolFramesRx Counter32
  swAuthEapLengthErrorFramesRx Counter32
  swAuthLastEapolFrameVersion Unsigned32
  swAuthLastEapolFrameSource MacAddress

SwMacAuthDiagEntry  
SEQUENCE    
  swAuthEntersConnecting Counter32
  swAuthEapLogoffsWhileConnecting Counter32
  swAuthEntersAuthenticating Counter32
  swAuthAuthSuccessWhileAuthenticating Counter32
  swAuthAuthTimeoutsWhileAuthenticating Counter32
  swAuthAuthFailWhileAuthenticating Counter32
  swAuthAuthReauthsWhileAuthenticating Counter32
  swAuthAuthEapStartsWhileAuthenticating Counter32
  swAuthAuthEapLogoffWhileAuthenticating Counter32
  swAuthAuthReauthsWhileAuthenticated Counter32
  swAuthAuthEapStartsWhileAuthenticated Counter32
  swAuthAuthEapLogoffWhileAuthenticated Counter32
  swAuthBackendResponses Counter32
  swAuthBackendAccessChallenges Counter32
  swAuthBackendOtherRequestsToSupplicant Counter32
  swAuthBackendNonNakResponsesFromSupplicant Counter32
  swAuthBackendAuthSuccesses Counter32
  swAuthBackendAuthFails Counter32

SwMacAuthSessionStatsEntry  
SEQUENCE    
  swAuthSessionOctetsRx Counter64
  swAuthSessionOctetsTx Counter64
  swAuthSessionFramesRx Counter32
  swAuthSessionFramesTx Counter32
  swAuthSessionId SnmpAdminString
  swAuthSessionAuthenticMethod INTEGER
  swAuthSessionTime TimeTicks
  swAuthSessionTerminateCause INTEGER
  swAuthSessionUserName SnmpAdminString

SwDot1xAuthStateEntry  
SEQUENCE    
  swDot1xAuthPortNumber InterfaceIndex
  swDot1xAuthVID INTEGER
  swDot1xAuthMACAddress MacAddress
  swDot1xAuthenticatorPAEState INTEGER
  swDot1xAuthBackendAuthState INTEGER
  swDot1xAuthAuthControlledStatus INTEGER
  swDot1xAuthAssignVID INTEGER
  swDot1xAuthAssignPriority INTEGER

SwDot1xAuthStatsEntry  
SEQUENCE    
  swDot1xAuthEapolFramesRx Counter32
  swDot1xAuthEapolFramesTx Counter32
  swDot1xAuthEapolStartFramesRx Counter32
  swDot1xAuthEapolLogoffFramesRx Counter32
  swDot1xAuthEapolRespIdFramesRx Counter32
  swDot1xAuthEapolRespFramesRx Counter32
  swDot1xAuthEapolReqIdFramesTx Counter32
  swDot1xAuthEapolReqFramesTx Counter32
  swDot1xAuthInvalidEapolFramesRx Counter32
  swDot1xAuthEapLengthErrorFramesRx Counter32
  swDot1xAuthLastEapolFrameVersion Unsigned32
  swDot1xAuthLastEapolFrameSource MacAddress

SwDot1xAuthDiagEntry  
SEQUENCE    
  swDot1xAuthEntersConnecting Counter32
  swDot1xAuthEapLogoffsWhileConnecting Counter32
  swDot1xAuthEntersAuthenticating Counter32
  swDot1xAuthAuthSuccessWhileAuthenticating Counter32
  swDot1xAuthAuthTimeoutsWhileAuthenticating Counter32
  swDot1xAuthAuthFailWhileAuthenticating Counter32
  swDot1xAuthAuthReauthsWhileAuthenticating Counter32
  swDot1xAuthAuthEapStartsWhileAuthenticating Counter32
  swDot1xAuthAuthEapLogoffWhileAuthenticating Counter32
  swDot1xAuthAuthReauthsWhileAuthenticated Counter32
  swDot1xAuthAuthEapStartsWhileAuthenticated Counter32
  swDot1xAuthAuthEapLogoffWhileAuthenticated Counter32
  swDot1xAuthBackendResponses Counter32
  swDot1xAuthBackendAccessChallenges Counter32
  swDot1xAuthBackendOtherRequestsToSupplicant Counter32
  swDot1xAuthBackendNonNakResponsesFromSupplicant Counter32
  swDot1xAuthBackendAuthSuccesses Counter32
  swDot1xAuthBackendAuthFails Counter32

SwDot1xAuthSessionStatsEntry  
SEQUENCE    
  swDot1xAuthSessionOctetsRx Counter64
  swDot1xAuthSessionOctetsTx Counter64
  swDot1xAuthSessionFramesRx Counter32
  swDot1xAuthSessionFramesTx Counter32
  swDot1xAuthSessionId SnmpAdminString
  swDot1xAuthSessionAuthenticMethod INTEGER
  swDot1xAuthSessionTime TimeTicks
  swDot1xAuthSessionTerminateCause INTEGER
  swDot1xAuthSessionUserName SnmpAdminString

SwAuthenticatedPortCtrlEntry  
SEQUENCE    
  swAuthenticatedPortNumber INTEGER
  swAuthenticatedPortCapabilities INTEGER

SwMacBasedPaePortEntry  
SEQUENCE    
  swMacBasedPaePortNumber InterfaceIndex
  swMacBasedPaeMacAddress MacAddress
  swMacBasedPaePortInitializeOrReauthStatus INTEGER

SwMacBasedPaeEntry  
SEQUENCE    
  swMacBasedPaePort InterfaceIndex
  swMacBasedPaeMac MacAddress
  swMacBasedPaeInitOrReauthStatus INTEGER

SwAuthStateEntry  
SEQUENCE    
  swAuthPortNumber InterfaceIndex
  swAuthMacAddress MacAddress
  swAuthAuthControlledStatus INTEGER
  swAuthAssignVid INTEGER
  swAuthAssignPriority INTEGER
  swAuthenticatorPAEState INTEGER
  swAuthBKdAuthState INTEGER

SwPaeAuthConfigEntry  
SEQUENCE    
  swPaeAuthFwdPdu INTEGER
  swPaeAuthMaxUser INTEGER

SwCompoundAuthPortEntry  
SEQUENCE    
  swCompoundAuthPortIndex INTEGER
  swCompoundAuthPortAuthMode INTEGER
  swCompoundAuthPortMethod INTEGER
  swCompoundAuthPortAuthVLANs DisplayString

SwGuestVlanEntry  
SEQUENCE    
  swGuestVlanId VlanId
  swGuestVlanPorts PortList
  swGuestVlanRowStatus RowStatus

Defined Values

swAuthCtrl 1.3.6.1.4.1.171.12.3
The Structure of Common Management Information for the security functions of the devices.
MODULE-IDENTITY    

swAuthenCtrl 1.3.6.1.4.1.171.12.3.1
OBJECT IDENTIFIER    

swRadiusCtrl 1.3.6.1.4.1.171.12.3.2
OBJECT IDENTIFIER    

swRadiusAuthInfo 1.3.6.1.4.1.171.12.3.3
OBJECT IDENTIFIER    

swRadiusAccountingCtrl 1.3.6.1.4.1.171.12.3.4
OBJECT IDENTIFIER    

swRadiusAccountingInfo 1.3.6.1.4.1.171.12.3.5
OBJECT IDENTIFIER    

swMacAuthBaseStatsInfo 1.3.6.1.4.1.171.12.3.6
OBJECT IDENTIFIER    

swRadiusCommand 1.3.6.1.4.1.171.12.3.7
OBJECT IDENTIFIER    

swAuthenticatedPortInfo 1.3.6.1.4.1.171.12.3.8
OBJECT IDENTIFIER    

swMacBasedPaePortInfo 1.3.6.1.4.1.171.12.3.9
OBJECT IDENTIFIER    

swPaeAuthenticator 1.3.6.1.4.1.171.12.3.10
OBJECT IDENTIFIER    

swCompoundAuthMgmt 1.3.6.1.4.1.171.12.3.11
OBJECT IDENTIFIER    

authProtocol 1.3.6.1.4.1.171.12.3.1.1
The authentication method used to authenticate users.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER authProtocolNone(1), authProtocolLocal(2), authProtocolRadius(3), authProtocolRadiusEap(4), authProtocolRadiusChap(5), authProtocolTacacs(6)  

swAuthMode 1.3.6.1.4.1.171.12.3.1.2
This object indicates the authentication mode of the device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER portBase(1), macBase(2)  

swAuthorizationState 1.3.6.1.4.1.171.12.3.1.3
This object indicates the authorization status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swAuthFailOver 1.3.6.1.4.1.171.12.3.1.4
This object indicates the fail over status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swRadiusDeadTime 1.3.6.1.4.1.171.12.3.2.1
Specifies the number of minutes when a RADIUS server that is not responding to authentication requests, is considered unavailable and will no longer accept further requests for RADIUS authentication.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

swRadiusTimeout 1.3.6.1.4.1.171.12.3.2.2
Specifies the number of seconds the NAS will wait for a reply to a RADIUS request before retransmitting the request.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

swRadiusRetransmitAttempts 1.3.6.1.4.1.171.12.3.2.3
Specifies the number of times the NAS transmits each RADIUS request to the server before giving up.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

swRadiusServerTable 1.3.6.1.4.1.171.12.3.2.4
The RADIUS server table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadiusServerEntry

swRadiusServerEntry 1.3.6.1.4.1.171.12.3.2.4.1
The entries of the RADIUS server table
Status: current Access: not-accessible
OBJECT-TYPE    
  RadiusServerEntry  

swRadiusServerIndex 1.3.6.1.4.1.171.12.3.2.4.1.1
The index of the RADIUS server
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER swRadiusServerIndex-first(1), swRadiusServerIndex-second(2), swRadiusServerIndex-third(3)  

swRadiusServerIpAddr 1.3.6.1.4.1.171.12.3.2.4.1.2
The IP address of the RADIUS server
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

swRadiusServerKey 1.3.6.1.4.1.171.12.3.2.4.1.3
The key of the RADIUS server
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

swRadiusAuthPortNumber 1.3.6.1.4.1.171.12.3.2.4.1.4
The UDP destination port number used for authentication requests to this server.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

swRadiusAcctPortNumber 1.3.6.1.4.1.171.12.3.2.4.1.5
The UDP destination port number used for accounting requests to this server
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

swRadiusServerStatus 1.3.6.1.4.1.171.12.3.2.4.1.6
The status of the RADIUS server
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

swRadiusServerTimeout 1.3.6.1.4.1.171.12.3.2.4.1.7
Specifies the number of seconds the NAS will wait for a reply to a RADIUS request before retransmitting the request.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

swRadiusServerRetransmit 1.3.6.1.4.1.171.12.3.2.4.1.8
Specifies the number of times the NAS transmits RADIUS requests to the server before giving up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

swRadiusServerAddrType 1.3.6.1.4.1.171.12.3.2.4.1.9
The type of RADIUS Server address as specified by object 'swRadiusServerAddr'.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

swRadiusServerAddr 1.3.6.1.4.1.171.12.3.2.4.1.10
The address of the RADIUS Server.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

swRadiusVrfName 1.3.6.1.4.1.171.12.3.2.5
This object is used to add or remove the VRF for 802.1X RADIUS
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..12)  

swRadiusAuthClientIdentifier 1.3.6.1.4.1.171.12.3.3.1
NAS Identifier. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..40)  

swRadiusAuthClientInvalidServerAddresses 1.3.6.1.4.1.171.12.3.3.2
Statistics infomation - The number of RADIUS Access-Response packets received from unknown addresses. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthServerTable 1.3.6.1.4.1.171.12.3.3.3
The authenticate table for the RADIUS server.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadiusAuthServerEntry

swRadiusAuthServerEntry 1.3.6.1.4.1.171.12.3.3.3.1
A list of RADIUS authentication servers. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  RadiusAuthServerEntry  

swRadiusAuthServerIndex 1.3.6.1.4.1.171.12.3.3.3.1.1
The RADIUS Server Index. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

swRadiusAuthServerAddress 1.3.6.1.4.1.171.12.3.3.3.1.2
The RADIUS authentication server address. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

swRadiusAuthClientServerPortNumber 1.3.6.1.4.1.171.12.3.3.3.1.3
The UDP socket port numbers. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

swRadiusAuthClientRoundTripTime 1.3.6.1.4.1.171.12.3.3.3.1.4
The round trip time counter from the RADIUS Authentication Client. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientAccessRequests 1.3.6.1.4.1.171.12.3.3.3.1.5
The number of access requests from a RADIUS Authentication Client. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientAccessRetransmissions 1.3.6.1.4.1.171.12.3.3.3.1.6
The number of retransmissions sent from the RADIUS Authentication Client. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientAccessAccepts 1.3.6.1.4.1.171.12.3.3.3.1.7
The number of authentication access attempts from the RADIUS Authentication Client. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientAccessRejects 1.3.6.1.4.1.171.12.3.3.3.1.8
The counter stating the Client Access Authentication rejections. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientAccessChallenges 1.3.6.1.4.1.171.12.3.3.3.1.9
The counter stating the number of Access challenges from RADIUS authentication attempts. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientMalformedAccessResponses 1.3.6.1.4.1.171.12.3.3.3.1.10
The counter for malformed access responses from RADIUS Authentication Clients. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientBadAuthenticators 1.3.6.1.4.1.171.12.3.3.3.1.11
The counter of bad authenticators from the RADIUS Authentication Client. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientPendingRequests 1.3.6.1.4.1.171.12.3.3.3.1.12
The counter of pending requests from the RADIUS Authentication Client. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientTimeouts 1.3.6.1.4.1.171.12.3.3.3.1.13
The counter of timeouts from a RADIUS Authentication Client. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientUnknownTypes 1.3.6.1.4.1.171.12.3.3.3.1.14
The counter for unknown types from a RADIUS Authentication Client. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAuthClientPacketsDropped 1.3.6.1.4.1.171.12.3.3.3.1.15
The counter of dropped packets from a RADIUS Authentication Client. It was made obsolete by RFC 2618 and RFC 2620.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

swRadiusAcctUpdateInterval 1.3.6.1.4.1.171.12.3.4.1
Time interval after which this RADIUS record should be updated and sent to an accounting server.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

swRadiusAcctSuppressNullUserName 1.3.6.1.4.1.171.12.3.4.2
Indicates whether or not accounting records will be generated for users with null names.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

swRadiusAcctServiceTable 1.3.6.1.4.1.171.12.3.4.3
RADIUS accounting Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcctServiceEntry

swRadiusAcctServiceEntry 1.3.6.1.4.1.171.12.3.4.3.1
The list of accounting services.
Status: current Access: not-accessible
OBJECT-TYPE    
  AcctServiceEntry  

swRadiusAcctServiceIndex 1.3.6.1.4.1.171.12.3.4.3.1.1
The Accounting table index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER acctServiceIndex-network(1), acctServiceIndex-exec(2), acctServiceIndex-system(3)  

swRadiusAcctServiceMethod 1.3.6.1.4.1.171.12.3.4.3.1.2
The accounting service method
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER swRadiusAcctServiceMethodNone(1), swRadiusAcctServiceMethodRadius(2)  

swRadiusAcctServiceMode 1.3.6.1.4.1.171.12.3.4.3.1.3
The accounting service mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER radiusAcctServiceModeNone(1), radiusAcctServiceModeStartStop(2), radiusAcctServiceModeStopOnly(3)  

swMacAuthStateTable 1.3.6.1.4.1.171.12.3.6.1
A table that contains the status objects for the Authenticator PAE associated with each virtual port (MAC address). An entry appears in this table for each virtual port that may authenticate access to itself.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMacAuthStateEntry

swMacAuthStateEntry 1.3.6.1.4.1.171.12.3.6.1.1
The information for an Authenticator PAE.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SwMacAuthStateEntry  

swPaeMacAddr 1.3.6.1.4.1.171.12.3.6.1.1.1
The address associated with this MAC address.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  MacAddress  

swPaePortNumber 1.3.6.1.4.1.171.12.3.6.1.1.2
The PAE Port number associated with this Port.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

swAuthPaeState 1.3.6.1.4.1.171.12.3.6.1.1.3
The current value of the Authenticator PAE state machine.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER initialize(1), disconnected(2), connecting(3), authenticating(4), authenticated(5), aborting(6), held(7), forceAuth(8), forceUnauth(9)  

swAuthBackendAuthState 1.3.6.1.4.1.171.12.3.6.1.1.4
The current state of the Backend Authentication state machine.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER request(1), response(2), success(3), fail(4), timeout(5), idle(6), initialize(7)  

swAuthAuthControlledPortStatus 1.3.6.1.4.1.171.12.3.6.1.1.5
The current value of the controlled Port status parameter for the Port.
Status: obsolete Access: read-only
OBJECT-TYPE    
  PaeControlledPortStatus  

swMacAuthStatsTable 1.3.6.1.4.1.171.12.3.6.2
A table that contains the statistics objects for the Authenticator PAE associated with each MAC address. An entry appears in this table for each MAC address that may authenticate access to itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMacAuthStatsEntry

swMacAuthStatsEntry 1.3.6.1.4.1.171.12.3.6.2.1
The statistics information for an Authenticator PAE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMacAuthStatsEntry  

swAuthEapolFramesRx 1.3.6.1.4.1.171.12.3.6.2.1.1
The number of valid EAPOL frames of any type that have been received by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthEapolFramesTx 1.3.6.1.4.1.171.12.3.6.2.1.2
The number of EAPOL frames of any type that have been transmitted by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthEapolStartFramesRx 1.3.6.1.4.1.171.12.3.6.2.1.3
The number of EAPOL Start frames that have been received by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthEapolLogoffFramesRx 1.3.6.1.4.1.171.12.3.6.2.1.4
The number of EAPOL logoff frames that have been received by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthEapolRespIdFramesRx 1.3.6.1.4.1.171.12.3.6.2.1.5
The number of EAP Resp/Id frames that have been received by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthEapolRespFramesRx 1.3.6.1.4.1.171.12.3.6.2.1.6
The number of valid EAP Response frames, other than Resp/Id frames, that have been received by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthEapolReqIdFramesTx 1.3.6.1.4.1.171.12.3.6.2.1.7
The number of EAP Req/Id frames that have been transmitted by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthEapolReqFramesTx 1.3.6.1.4.1.171.12.3.6.2.1.8
The number of EAP Request frames, other than Rq/Id frames, that have been transmitted by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthInvalidEapolFramesRx 1.3.6.1.4.1.171.12.3.6.2.1.9
The number of EAPOL frames that have been received by this Authenticator for which the frame type is not recognized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthEapLengthErrorFramesRx 1.3.6.1.4.1.171.12.3.6.2.1.10
The number of EAPOL frames that have been received by this Authenticator for which the Packet Body Length field is invalid.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthLastEapolFrameVersion 1.3.6.1.4.1.171.12.3.6.2.1.11
The protocol version number carried in the most recently received EAPOL frame.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

swAuthLastEapolFrameSource 1.3.6.1.4.1.171.12.3.6.2.1.12
The source MAC address carried in the most recently received EAPOL frame.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

swMacAuthDiagTable 1.3.6.1.4.1.171.12.3.6.3
A table that contains the diagnostics objects for the Authenticator PAE associated with each MAC address. An entry appears in this table for each MAC address that may authenticate access to itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMacAuthDiagEntry

swMacAuthDiagEntry 1.3.6.1.4.1.171.12.3.6.3.1
The diagnostics information for an Authenticator PAE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMacAuthDiagEntry  

swAuthEntersConnecting 1.3.6.1.4.1.171.12.3.6.3.1.1
Counts the number of times that the state machine transitions to a CONNECTING state from any other state.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthEapLogoffsWhileConnecting 1.3.6.1.4.1.171.12.3.6.3.1.2
Counts the number of times that the state machine transitions from CONNECTING to DISCONNECTED as a result of receiving an EAPOL-Logoff message.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthEntersAuthenticating 1.3.6.1.4.1.171.12.3.6.3.1.3
Counts the number of times that the state machine transitions from CONNECTING to AUTHENTICATING, as a result of an EAP-Response/Identity message being received from the Supplicant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthAuthSuccessWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.3.1.4
Counts the number of times that the state machine transitions from AUTHENTICATING to AUTHENTICATED, as a result of the Backend Authentication state machine, indicating successful authentication of the Supplicant (authSuccess = TRUE).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthAuthTimeoutsWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.3.1.5
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of the Backend Authentication state machine indicating authentication timeout (authTimeout = TRUE).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthAuthFailWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.3.1.6
Counts the number of times that the state machine transitions from AUTHENTICATING to HELD, as a result of the Backend Authentication state machine indicating authentication failure (authFail = TRUE).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthAuthReauthsWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.3.1.7
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of a reauthentication request (reAuthenticate = TRUE).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthAuthEapStartsWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.3.1.8
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of an EAPOL-Start message being received from the Supplicant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthAuthEapLogoffWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.3.1.9
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of an EAPOL-Logoff message being received from the Supplicant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthAuthReauthsWhileAuthenticated 1.3.6.1.4.1.171.12.3.6.3.1.10
Counts the number of times that the state machine transitions from AUTHENTICATED to CONNECTING, as a result of a reauthentication request (reAuthenticate = TRUE).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthAuthEapStartsWhileAuthenticated 1.3.6.1.4.1.171.12.3.6.3.1.11
Counts the number of times that the state machine transitions from AUTHENTICATED to CONNECTING, as a result of an EAPOL-Start message received from the Supplicant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthAuthEapLogoffWhileAuthenticated 1.3.6.1.4.1.171.12.3.6.3.1.12
Counts the number of times that the state machine transitions from AUTHENTICATED to DISCONNECTED, as a result of an EAPOL-Logoff message received from the Supplicant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthBackendResponses 1.3.6.1.4.1.171.12.3.6.3.1.13
Counts the number of times that the state machine sends an initial Access-Request packet to the Authentication server (i.e., executes sendRespToServer on entry to the RESPONSE state). Indicates that the Authenticator attempted communication with the Authentication Server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthBackendAccessChallenges 1.3.6.1.4.1.171.12.3.6.3.1.14
Counts the number of times that the state machine receives an initial Access-Challenge packet from the Authentication server (i.e., aReq becomes TRUE, causing exit from the RESPONSE state). Indicates that the Authentication Server has communication with the Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthBackendOtherRequestsToSupplicant 1.3.6.1.4.1.171.12.3.6.3.1.15
Counts the number of times that the state machine sends an EAP-Request packet (other than an Identity, Notification, Failure or Success message) to the Supplicant (i.e., executes txReq on entry to the REQUEST state). Indicates that the Authenticator chose an EAP-method.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthBackendNonNakResponsesFromSupplicant 1.3.6.1.4.1.171.12.3.6.3.1.16
Counts the number of times that the state machine receives a response from the Supplicant to an initial EAP-Request, and the response is something other than EAP-NAK (i.e., rxResp becomes TRUE, causing the state machine to transition from REQUEST to RESPONSE, and the response is not an EAP-NAK). Indicates that the Supplicant can respond to the Authenticator's chosen EAP-method.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthBackendAuthSuccesses 1.3.6.1.4.1.171.12.3.6.3.1.17
Counts the number of times that the state machine receives an EAP-Success message from the Authentication Server (i.e., a Success becomes TRUE, causing a transition from RESPONSE to SUCCESS). Indicates that the Supplicant has successfully authenticated to the Authentication Server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthBackendAuthFails 1.3.6.1.4.1.171.12.3.6.3.1.18
Counts the number of times that the state machine receives an EAP-Failure message from the Authentication Server (i.e., a Fail becomes TRUE, causing a transition from RESPONSE to FAIL). Indicates that the Supplicant has not authenticated to the Authentication Server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swMacAuthSessionStatsTable 1.3.6.1.4.1.171.12.3.6.4
A table that contains the session statistics objects for the Authenticator PAE associated with each MAC address. An entry appears in this table for each MAC address that may authenticate access to itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMacAuthSessionStatsEntry

swMacAuthSessionStatsEntry 1.3.6.1.4.1.171.12.3.6.4.1
The session statistics information for an Authenticator PAE. This shows the current values being collected for each session that is still in progress, or the final values for the last valid session on each MAC address where there is no session currently active.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMacAuthSessionStatsEntry  

swAuthSessionOctetsRx 1.3.6.1.4.1.171.12.3.6.4.1.1
The number of octets received in user data frames from this MAC address during the session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

swAuthSessionOctetsTx 1.3.6.1.4.1.171.12.3.6.4.1.2
The number of octets transmitted in user data frames to this MAC address during the session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

swAuthSessionFramesRx 1.3.6.1.4.1.171.12.3.6.4.1.3
The number of user data frames received from this MAC address during the session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthSessionFramesTx 1.3.6.1.4.1.171.12.3.6.4.1.4
The number of user data frames transmitted to this MAC address during the session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swAuthSessionId 1.3.6.1.4.1.171.12.3.6.4.1.5
A unique identifier for the session, in the form of a printable ASCII string of at least three characters.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

swAuthSessionAuthenticMethod 1.3.6.1.4.1.171.12.3.6.4.1.6
The authentication method used to establish the session.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER remoteAuthServer(1), localAuthServer(2)  

swAuthSessionTime 1.3.6.1.4.1.171.12.3.6.4.1.7
The duration of the session in units of hundredth of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

swAuthSessionTerminateCause 1.3.6.1.4.1.171.12.3.6.4.1.8
The reason for the session termination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER supplicantLogoff(1), portFailure(2), supplicantRestart(3), reauthFailed(4), authControlForceUnauth(5), portReInit(6), portAdminDisabled(7), notTerminatedYet(999)  

swAuthSessionUserName 1.3.6.1.4.1.171.12.3.6.4.1.9
The User-Name representing the identity of the Supplicant PAE.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

swDot1xAuthStateTable 1.3.6.1.4.1.171.12.3.6.5
A table that contains the status objects for the Authenticator PAE associated with each host. An entry appears in this table for each host that may authenticate access to itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwDot1xAuthStateEntry

swDot1xAuthStateEntry 1.3.6.1.4.1.171.12.3.6.5.1
The information for an Authenticator PAE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwDot1xAuthStateEntry  

swDot1xAuthPortNumber 1.3.6.1.4.1.171.12.3.6.5.1.1
The Port number associated with this host.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

swDot1xAuthVID 1.3.6.1.4.1.171.12.3.6.5.1.2
The Original VID associated with this host.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swDot1xAuthMACAddress 1.3.6.1.4.1.171.12.3.6.5.1.3
The MAC address associated with this host.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

swDot1xAuthenticatorPAEState 1.3.6.1.4.1.171.12.3.6.5.1.4
The current value of the Authenticator PAE state machine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initialize(1), disconnected(2), connecting(3), authenticating(4), authenticated(5), aborting(6), held(7), forceAuth(8), forceUnauth(9)  

swDot1xAuthBackendAuthState 1.3.6.1.4.1.171.12.3.6.5.1.5
The current state of the Backend Authentication state machine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER request(1), response(2), success(3), fail(4), timeout(5), idle(6), initialize(7)  

swDot1xAuthAuthControlledStatus 1.3.6.1.4.1.171.12.3.6.5.1.6
The authenticate state of the host.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER authenticating(1), authorized(2), unauthorized(3)  

swDot1xAuthAssignVID 1.3.6.1.4.1.171.12.3.6.5.1.7
The VID assigned by the RADIUS server.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swDot1xAuthAssignPriority 1.3.6.1.4.1.171.12.3.6.5.1.8
The priority assigned by the RADIUS server.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swDot1xAuthStatsTable 1.3.6.1.4.1.171.12.3.6.6
A table that contains the statistics objects for the Authenticator PAE associated with each host. An entry appears in this table for each host that may authenticate access to itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwDot1xAuthStatsEntry

swDot1xAuthStatsEntry 1.3.6.1.4.1.171.12.3.6.6.1
The statistics information for an Authenticator PAE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwDot1xAuthStatsEntry  

swDot1xAuthEapolFramesRx 1.3.6.1.4.1.171.12.3.6.6.1.1
The number of valid EAPOL frames of any type that have been received by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthEapolFramesTx 1.3.6.1.4.1.171.12.3.6.6.1.2
The number of EAPOL frames of any type that have been transmitted by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthEapolStartFramesRx 1.3.6.1.4.1.171.12.3.6.6.1.3
The number of EAPOL Start frames that have been received by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthEapolLogoffFramesRx 1.3.6.1.4.1.171.12.3.6.6.1.4
The number of EAPOL Logoff frames that have been received by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthEapolRespIdFramesRx 1.3.6.1.4.1.171.12.3.6.6.1.5
The number of EAP Resp/Id frames that have been received by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthEapolRespFramesRx 1.3.6.1.4.1.171.12.3.6.6.1.6
The number of valid EAP Response frames (other than Resp/Id frames) that have been received by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthEapolReqIdFramesTx 1.3.6.1.4.1.171.12.3.6.6.1.7
The number of EAP Req/Id frames that have been transmitted by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthEapolReqFramesTx 1.3.6.1.4.1.171.12.3.6.6.1.8
The number of EAP Request frames (other than Rq/Id frames) that have been transmitted by this Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthInvalidEapolFramesRx 1.3.6.1.4.1.171.12.3.6.6.1.9
The number of EAPOL frames that have been received by this Authenticator for which the frame type is not recognized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthEapLengthErrorFramesRx 1.3.6.1.4.1.171.12.3.6.6.1.10
The number of EAPOL frames that have been received by this Authenticator for which the Packet Body Length field is invalid.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthLastEapolFrameVersion 1.3.6.1.4.1.171.12.3.6.6.1.11
The protocol version number carried in the most recently received EAPOL frame.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

swDot1xAuthLastEapolFrameSource 1.3.6.1.4.1.171.12.3.6.6.1.12
The source MAC address carried in the most recently received EAPOL frame.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

swDot1xAuthDiagTable 1.3.6.1.4.1.171.12.3.6.7
A table that contains the diagnostics objects for the Authenticator PAE associated with each host. An entry appears in this table for each MAC address that may authenticate access to itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwDot1xAuthDiagEntry

swDot1xAuthDiagEntry 1.3.6.1.4.1.171.12.3.6.7.1
The diagnostics information for an Authenticator PAE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwDot1xAuthDiagEntry  

swDot1xAuthEntersConnecting 1.3.6.1.4.1.171.12.3.6.7.1.1
Counts the number of times that the state machine transitions to a CONNECTING state from any other state.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthEapLogoffsWhileConnecting 1.3.6.1.4.1.171.12.3.6.7.1.2
Counts the number of times that the state machine transitions from CONNECTING to DISCONNECTED as a result of receiving an EAPOL-Logoff message.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthEntersAuthenticating 1.3.6.1.4.1.171.12.3.6.7.1.3
Counts the number of times that the state machine transitions from CONNECTING to AUTHENTICATING, as a result of an EAP-Response/Identity message being received from the Supplicant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthAuthSuccessWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.7.1.4
Counts the number of times that the state machine transitions from AUTHENTICATING to AUTHENTICATED, as a result of the Backend Authentication state machine, indicating successful authentication of the Supplicant (authSuccess = TRUE).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthAuthTimeoutsWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.7.1.5
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of the Backend Authentication state machine indicating an authentication timeout (authTimeout = TRUE).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthAuthFailWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.7.1.6
Counts the number of times that the state machine transitions from AUTHENTICATING to HELD, as a result of the Backend Authentication state machine indicating an authentication failure (authFail = TRUE).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthAuthReauthsWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.7.1.7
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of a reauthentication request (reAuthenticate = TRUE).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthAuthEapStartsWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.7.1.8
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of an EAPOL-Start message being received from the Supplicant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthAuthEapLogoffWhileAuthenticating 1.3.6.1.4.1.171.12.3.6.7.1.9
Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of an EAPOL-Logoff message being received from the Supplicant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthAuthReauthsWhileAuthenticated 1.3.6.1.4.1.171.12.3.6.7.1.10
Counts the number of times that the state machine transitions from AUTHENTICATED to CONNECTING, as a result of a reauthentication request (reAuthenticate = TRUE).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthAuthEapStartsWhileAuthenticated 1.3.6.1.4.1.171.12.3.6.7.1.11
Counts the number of times that the state machine transitions from AUTHENTICATED to CONNECTING, as a result of an EAPOL-Start message being received from the Supplicant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthAuthEapLogoffWhileAuthenticated 1.3.6.1.4.1.171.12.3.6.7.1.12
Counts the number of times that the state machine transitions from AUTHENTICATED to DISCONNECTED, as a result of an EAPOL-Logoff message being received from the Supplicant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthBackendResponses 1.3.6.1.4.1.171.12.3.6.7.1.13
Counts the number of times that the state machine sends an initial Access-Request packet to the Authentication server (i.e., executes sendRespToServer on entry to the RESPONSE state). Indicates that the Authenticator attempted communication with the Authentication Server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthBackendAccessChallenges 1.3.6.1.4.1.171.12.3.6.7.1.14
Counts the number of times that the state machine receives an initial Access-Challenge packet from the Authentication server (i.e., aReq becomes TRUE, causing exit from the RESPONSE state). Indicates that the Authentication Server has communication with the Authenticator.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthBackendOtherRequestsToSupplicant 1.3.6.1.4.1.171.12.3.6.7.1.15
Counts the number of times that the state machine sends an EAP-Request packet (other than an Identity, Notification, Failure or Success message) to the Supplicant (i.e., executes txReq on entry to the REQUEST state). Indicates that the Authenticator chose an EAP-method.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthBackendNonNakResponsesFromSupplicant 1.3.6.1.4.1.171.12.3.6.7.1.16
Counts the number of times that the state machine receives a response from the Supplicant to an initial EAP-Request, and the response is something other than EAP-NAK (i.e., rxResp becomes TRUE, causing the state machine to transition from REQUEST to RESPONSE, and the response is not an EAP-NAK). Indicates that the Supplicant can respond to the Authenticator's chosen EAP-method.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthBackendAuthSuccesses 1.3.6.1.4.1.171.12.3.6.7.1.17
Counts the number of times that the state machine receives an EAP-Success message from the Authentication Server (i.e., a Success becomes TRUE, causing a transition from RESPONSE to SUCCESS). Indicates that the Supplicant has successfully authenticated to the Authentication Server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthBackendAuthFails 1.3.6.1.4.1.171.12.3.6.7.1.18
Counts the number of times that the state machine receives an EAP-Failure message from the Authentication Server (i.e., a Fail becomes TRUE, causing a transition from RESPONSE to FAIL). Indicates that the Supplicant has not authenticated to the Authentication Server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthSessionStatsTable 1.3.6.1.4.1.171.12.3.6.8
A table that contains the session statistics objects for the Authenticator PAE associated with each host. An entry appears in this table for each host that may authenticate access to itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwDot1xAuthSessionStatsEntry

swDot1xAuthSessionStatsEntry 1.3.6.1.4.1.171.12.3.6.8.1
The session statistics information for an Authenticator PAE. This shows the current values being collected for each session that is still in progress, or the final values for the last valid session on each host where there is no session currently active.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwDot1xAuthSessionStatsEntry  

swDot1xAuthSessionOctetsRx 1.3.6.1.4.1.171.12.3.6.8.1.1
The number of octets received in user data frames from this host during the session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

swDot1xAuthSessionOctetsTx 1.3.6.1.4.1.171.12.3.6.8.1.2
The number of octets transmitted in user data frames to this host during the session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

swDot1xAuthSessionFramesRx 1.3.6.1.4.1.171.12.3.6.8.1.3
The number of user data frames received from this host during the session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthSessionFramesTx 1.3.6.1.4.1.171.12.3.6.8.1.4
The number of user data frames transmitted to this host during the session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

swDot1xAuthSessionId 1.3.6.1.4.1.171.12.3.6.8.1.5
A unique identifier for the session, in the form of a printable ASCII string of at least three characters.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

swDot1xAuthSessionAuthenticMethod 1.3.6.1.4.1.171.12.3.6.8.1.6
The authentication method used to establish the session.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER remoteAuthServer(1), localAuthServer(2)  

swDot1xAuthSessionTime 1.3.6.1.4.1.171.12.3.6.8.1.7
The duration of the session in units of hundredth of a second.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

swDot1xAuthSessionTerminateCause 1.3.6.1.4.1.171.12.3.6.8.1.8
The reason for the session termination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER supplicantLogoff(1), portFailure(2), supplicantRestart(3), reauthFailed(4), authControlForceUnauth(5), portReInit(6), portAdminDisabled(7), notTerminatedYet(999)  

swDot1xAuthSessionUserName 1.3.6.1.4.1.171.12.3.6.8.1.9
The User-Name representing the identity of the Supplicant PAE.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

swRadiusForceDownPortNumber 1.3.6.1.4.1.171.12.3.7.1
The port number on which the RADIUS server is forced to terminate the network service.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

swRadiusForceDownMacAddr 1.3.6.1.4.1.171.12.3.7.2
The user's MAC address on which the RADIUS server is forced to terminate the network service.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

swAuthenticatedPortCtrlTable 1.3.6.1.4.1.171.12.3.8.1
A table used to configure the port's 802.1x capability.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwAuthenticatedPortCtrlEntry

swAuthenticatedPortCtrlEntry 1.3.6.1.4.1.171.12.3.8.1.1
The Port number and authenticator control for a Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwAuthenticatedPortCtrlEntry  

swAuthenticatedPortNumber 1.3.6.1.4.1.171.12.3.8.1.1.1
The Authenticated Port number associated with this Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

swAuthenticatedPortCapabilities 1.3.6.1.4.1.171.12.3.8.1.1.2
Indicates the PAE functionality that this Port supports and that it may be managed through this MIB.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), authenticator(2)  

swMacBasedPaePortTable 1.3.6.1.4.1.171.12.3.9.1
A table of system level information for each port supported by the MAC-based Port Access Entity. An entry appears in this table for each port of this system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMacBasedPaePortEntry

swMacBasedPaePortEntry 1.3.6.1.4.1.171.12.3.9.1.1
The port number, protocol version and initialization control for a Port by MAC based mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMacBasedPaePortEntry  

swMacBasedPaePortNumber 1.3.6.1.4.1.171.12.3.9.1.1.1
The port number associated with this Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

swMacBasedPaeMacAddress 1.3.6.1.4.1.171.12.3.9.1.1.2
Specifies the MAC address used to initialize the 802.1X authentication state machine of some or all ports or used to reauthenticate the device connected to the port.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

swMacBasedPaePortInitializeOrReauthStatus 1.3.6.1.4.1.171.12.3.9.1.1.3
This is used to execute MAC-Based Port initialization or reauthentication, so it is necessary to set swMacBasedPaeMacAddress before this action can be initialized. Choosing 'initialize' causes the port to be initialized in MAC-based mode. Choosing 'reauthenticate' causes the port to be reauthenticated in MAC-based mode. The attribute value reverts to 'other' once the initialization or reauthentication has been done.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), initialize(2), reauthenticate(3)  

swMacBasedPaeTable 1.3.6.1.4.1.171.12.3.9.2
A table used to reauthenticate or initialize a host.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMacBasedPaeEntry

swMacBasedPaeEntry 1.3.6.1.4.1.171.12.3.9.2.1
The port number, MAC address and initialization or reauthentication control for a host by MAC based mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMacBasedPaeEntry  

swMacBasedPaePort 1.3.6.1.4.1.171.12.3.9.2.1.1
The port number associated with this Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

swMacBasedPaeMac 1.3.6.1.4.1.171.12.3.9.2.1.2
Specifies the MAC address used to initialize the 802.1X authentication state machine of the host or used to reauthenticate the host on the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

swMacBasedPaeInitOrReauthStatus 1.3.6.1.4.1.171.12.3.9.2.1.3
This is used to execute MAC-based Port initialization or reauthentication. Choosing 'initialize' causes the host to be initialized in MAC-based mode. Choosing 'reauthenticate' causes the host to be reauthenticated in MAC-based mode. The attribute value reverts to 'other' once the initialization or reauthentication has been done.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), initialize(2), reauthenticate(3)  

swPaeAuthSysFwdPdu 1.3.6.1.4.1.171.12.3.10.1
This object indicates the global setting to control the forwarding of the EAPOL PDU.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swPaeAuthSysMaxUser 1.3.6.1.4.1.171.12.3.10.2
This object indicates the global limitation on the maximum number of users that can be learned via 802.1X authentication. The maximum entry range is (0..N), the value N means the maximum number. It is determined by the project itself. Value 0 means no-limit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

swPaeAuthConfigTable 1.3.6.1.4.1.171.12.3.10.3
A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwPaeAuthConfigEntry

swAuthStateTable 1.3.6.1.4.1.171.12.3.10.4
A table that contains the status objects for the Authenticator PAE associated with each host. An entry appears in this table for each host that may authenticate access to itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwAuthStateEntry

swAuthStateEntry 1.3.6.1.4.1.171.12.3.10.4.1
The information for an Authenticator PAE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwAuthStateEntry  

swAuthPortNumber 1.3.6.1.4.1.171.12.3.10.4.1.1
The PAE Port number associated with this Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

swAuthMacAddress 1.3.6.1.4.1.171.12.3.10.4.1.2
The address associated with this MAC address.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

swAuthAuthControlledStatus 1.3.6.1.4.1.171.12.3.10.4.1.3
The authenticate state of the host.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER authenticating(1), authorized(2), unauthorized(3)  

swAuthAssignVid 1.3.6.1.4.1.171.12.3.10.4.1.4
The VID assigned by the RADIUS server.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swAuthAssignPriority 1.3.6.1.4.1.171.12.3.10.4.1.5
The priority assigned by the RADIUS server.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swAuthenticatorPAEState 1.3.6.1.4.1.171.12.3.10.4.1.6
The current value of the Authenticator PAE state machine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initialize(1), disconnected(2), connecting(3), authenticating(4), authenticated(5), aborting(6), held(7), forceAuth(8), forceUnauth(9)  

swAuthBKdAuthState 1.3.6.1.4.1.171.12.3.10.4.1.7
The current state of the Backend Authentication state machine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER request(1), response(2), success(3), fail(4), timeout(5), idle(6), initialize(7)  

swPaeAuthConfigEntry 1.3.6.1.4.1.171.12.3.10.3.1
The configuration information for an Authenticator PAE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwPaeAuthConfigEntry  

swPaeAuthFwdPdu 1.3.6.1.4.1.171.12.3.10.3.1.1
This object indicates the per port setting to control the forwarding of EAPOL PDU.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swPaeAuthMaxUser 1.3.6.1.4.1.171.12.3.10.3.1.2
This object indicates the limitation on the maximum number of users by port. The max entry range is (0..N), the value N means the max number. It is determined by project itself. Value 0 means no-limit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

swCompoundAuthPortTable 1.3.6.1.4.1.171.12.3.11.1
A table that contains compound authentication information for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwCompoundAuthPortEntry

swCompoundAuthPortEntry 1.3.6.1.4.1.171.12.3.11.1.1
The compound authentication configuration information for a port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwCompoundAuthPortEntry  

swCompoundAuthPortIndex 1.3.6.1.4.1.171.12.3.11.1.1.1
The compound authentication port number associated with this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

swCompoundAuthPortAuthMode 1.3.6.1.4.1.171.12.3.11.1.1.2
This object sets the authorization mode. Port-based: If one of the attached hosts passes the authentication, all the hosts on the same port will be granted access to the network. If the user fails the authorization, this port will keep trying the next authentication. Host-based: Every user can be authenticated individually. The client can start authentication on specific authentication VLAN(s).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER hostbased(1), portbased(2)  

swCompoundAuthPortMethod 1.3.6.1.4.1.171.12.3.11.1.1.3
This object sets the method for compound authentication settings. None: The system level setting of individual authentication still takes effect. Thus suppose that the compound authentication method of a port is set to any but MAC-AC is disabled, JWAC and 802.1x enabled, then the user must pass either the JWAC or 802.1x method. The following is the relation of the compound authentication method and the configuration of the individual authentication method. (1) If compound authentication methods is not set to none: The port's authentication method will depend on the compound authentication method. An individual authentication method's setting is ignored. (2) If compound authentication methods is set to none: This port is in single-auth mode. The port's authentication method will depend on the individual authentication method's setting. Any: If any one of the authentication methods (802.1x, MAC-AC, WAC and JWAC) passes, then pass. dot1xImpb: Dot1x will be verified first, and then IMPB will be verified. Both authentication methods need to be passed to make the authentication successful. impbJwac: IMPB will be verified first, and then JWAC will be verified. Both authentication methods need to be passed to make the authentication successful. impbWac: IMPB will be verified first, and then WAC will be verified. Both authentication methods need to be passed to make the authentication successful. macImpb: MAC-AC will be verified first, and then IMPB will be verified. Both authentication methods need to be passed to make the authentication successful. macJwac: MAC-AC will be verified first. If client passed MAC authentication, JWAC will be verified. Both authentication methods need to be passed to make the authentication successful.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), any(2), dot1xImpb(3), impbJwac(4), impbWac(5), macImpb(6), macJwac(7)  

swCompoundAuthPortAuthVLANs 1.3.6.1.4.1.171.12.3.11.1.1.4
This object sets the Authentication VLAN(s). If the authentication VLAN is not specified, It means to not care which VLAN the client comes from, the client will be authenticated if the client's MAC (not care the VLAN) is not authenticated. After the client is authenticated, the client will not be reauthenticated when received from other VLANs. When the port's authorization mode is changed to port based, previously authentication VLAN(s) on this port will be cleared. Note: For the compound VLAN specification, the value should be separated by ',' or '-'. Such as: 1,4,7 or 1,4,7-9 .
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

swGuestVlanTable 1.3.6.1.4.1.171.12.3.11.2
A table containing configuration information for guest VLANs configured into the device by local or network management. All entries are permanent and will be restored after the device reset.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwGuestVlanEntry

swGuestVlanEntry 1.3.6.1.4.1.171.12.3.11.2.1
Information for a guest VLAN configured into the device by local or network management.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwGuestVlanEntry  

swGuestVlanId 1.3.6.1.4.1.171.12.3.11.2.1.1
The VLAN ID referring to this guest VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  VlanId  

swGuestVlanPorts 1.3.6.1.4.1.171.12.3.11.2.1.2
The set of ports which are permanently assigned to the guest VLAN member for this guest VLAN by management. Note: For on-going projects which need to support old-style commands as well, the rules for guest VLAN setting are: (1) Compound authentication mode is not none: You need to specify the guest VLAN by this command or individual authentication method's guest VLAN setting will be ignored. (2) Compound authentication mode is none: This port is in single authentication mode. Individual authentications use their guest VLAN settings configured by their individual guest VLAN commands. The setting of config guest_vlan will be ignored
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swGuestVlanRowStatus 1.3.6.1.4.1.171.12.3.11.2.1.3
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swAuthorizationAttributes 1.3.6.1.4.1.171.12.3.11.3
This object indicates the authorization status. When the authorization for attributes is enabled, whether the authorized attributes (for example VLAN, 802.1p default priority, and ACL) assigned by the RADIUS server or local database will be accepted or not will depend on the individual module setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swAuthServerFailoverState 1.3.6.1.4.1.171.12.3.11.4
This object indicates the authentication server failover state. block: Block the client. local: Use the local DB to authenticate the client. permit: The client is always regarded as authenticated.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER block(1), local(2), permit(3)  

swAuthMACFormatCase 1.3.6.1.4.1.171.12.3.11.5
This object indicates the case format of the authentication MAC address for RADIUS authentication. uppercase: Using uppercase format, the formatted is: AA-BB-CC-DD-EE-FF. lowercase: Using lowercase format, the formatted is: aa-bb-cc-dd-ee-ff.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uppercase(1), lowercase(2)  

swAuthMACFormatDelimiter 1.3.6.1.4.1.171.12.3.11.6
This object indicates the delimiter format of authentication MAC address for RADIUS authentication. none: Not using any delimiter, the format is: AABBCCDDEEFF hyphen: Using '-' as delimiter, the format is: AA-BB-CC-DD-EE-FF colon: Using ':' as delimiter, the format is: AA:BB:CC:DD:EE:FF dot: Using '.' as delimiter, the format is: AA.BB.CC.DD.EE.FF
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), hyphen(2), colon(3), dot(4)  

swAuthMACFormatDelimiterNumber 1.3.6.1.4.1.171.12.3.11.7
This object indicates the delimiter number of authentication MAC address for RADIUS authentication. delimiter-number-1: single delimiter, the format is: AABBCC.DDEEFF delimiter-number-2: double delimiter, the format is: AABB.CCDD.EEFF delimiter-number-5: multiple delimiter, the format is: AA.BB.CC.DD.EE.FF Note: while swAuthMACFormatDelimiter is none(1), the delimiter number will not take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER delimiter-number-1(1), delimiter-number-2(2), delimiter-number-5(3)