BDCOM-IF-THRESHOLD-MIB

File: BDCOM-IF-THRESHOLD-MIB.mib (51604 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
SNMP-FRAMEWORK-MIB	BDCOM-SMI	IF-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Integer32	Unsigned32	TEXTUAL-CONVENTION
RowStatus	TimeStamp	TruthValue
MODULE-COMPLIANCE	OBJECT-GROUP	NOTIFICATION-GROUP
SnmpAdminString	bdMgmt	InterfaceIndex
ifIndex

Defined Types

BdifthTemplateIndex
An arbitrary integer that uniquely identifies a threshold template. The value for each threshold template must remain constant at least from one re-initialization of the agent's network management system to the next re-initialization. The value may change when the agent's network management system is rebooted or re-initialized.
TEXTUAL-CONVENTION
	Unsigned32	1..1000

BdifthTemplateIndexOrZero
A value of either '0' or a valid template index. The distinguished value '0' indicates no template or no unassigned template index values are available.
TEXTUAL-CONVENTION
	Unsigned32	0..1000

BdifthThresholdIndex
An arbitrary integer that uniquely identifies a threshold within a threshold template. The value for each threshold must remain constant when the agent's network management system is rebooted or re-initialized.
TEXTUAL-CONVENTION
	Unsigned32	0..63

BdifthThresholdList
A list of thresholds defined in a given template, in which each bit represents one threshold. The bits in the first octet represent thresholds identified by bdifthThresholdIndex values 0 through 7, inclusive. The bits in the second octet represent thresholds identified by integer values 8 through 15, inclusive, and so forth. The least significant bit of an octet represents the threshold identified by the lowest integer value, and the most significant bit represents the threshold identified by the highest integer value. The figure shown below illustrates the format of a threshold list. Octet 1 Octet 8 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 +-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+ | |...| | +-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | +- Threshold 56 | | | | | | | | | | | | | | +--- Threshold 57 | | | | | | | | | | | | | +----- Threshold 58 | | | | | | | | | | | | +------- Threshold 59 | | | | | | | | | | | +--------- Threshold 60 | | | | | | | | | | +----------- Threshold 61 | | | | | | | | | +------------- Threshold 62 | | | | | | | | +--------------- Threshold 63 | | | | | | | | : | | | | | | | | : | | | | | | | +--------------------- Threshold 0 | | | | | | +----------------------- Threshold 1 | | | | | +------------------------- Threshold 2 | | | | +--------------------------- Threshold 3 | | | +----------------------------- Threshold 4 | | +------------------------------- Threshold 5 | +--------------------------------- Threshold 6 +----------------------------------- Threshold 7 A bit value of '1' indicates that the threshold is being exceeded in current operation (i.e., the threshold is fired). A bit value of '0' indicates that the threshold is not being exceeded in current operation (i.e., the threshold is cleared). A threshold list of length N, where N < 8, represents a threshold list for which thresholds N*8 through 63 have the value of '0'. A special case is a threshold list having a length of '0', which represents a threshold list of all zeros.
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..8)

BdifthThresholdSeverity
The severity of the condition when the threshold is fired. A smaller enumerated integer value indicates that the threshold exceeded condition is more severe. The value 'fail' indicates a hard failure condition where no data can be received, or where the data received has a large number of errors which makes it impossible to recover most of the data. The value 'degrade' indicates a soft failure condition in which data received on this interface is affected, but a significant portion of the data can be recovered. The value 'info' is used to raise attention to a condition that could possibly be an impending problem or to notify the customer of an event that improves operation.
TEXTUAL-CONVENTION
	INTEGER	fail(1), degrade(2), info(3), other(4)

BdifthThresholdSeverityOrZero
A value of either '0' or a valid threshold severity.
TEXTUAL-CONVENTION
	INTEGER	0..4

BdifthTemplateEntry
SEQUENCE
	bdifthTemplateIndex	BdifthTemplateIndex
	bdifthTemplateName	SnmpAdminString
	bdifthTemplateNotifyHoldDownType	INTEGER
	bdifthTemplateNotifyHoldDownTime	Unsigned32
	bdifthTemplateRowStatus	RowStatus

BdifthThresholdEntry
SEQUENCE
	bdifthThresholdIndex	BdifthThresholdIndex
	bdifthThresholdDescr	SnmpAdminString
	bdifthThresholdObject	OBJECT IDENTIFIER
	bdifthThresholdSeverity	BdifthThresholdSeverity
	bdifthThresholdType	INTEGER
	bdifthThresholdDirection	INTEGER
	bdifthThresholdFiredValue	Integer32
	bdifthThresholdClearedValue	Integer32
	bdifthThresholdSampleInterval	Unsigned32
	bdifthThresholdApsSwitchover	TruthValue
	bdifthThresholdRowStatus	RowStatus

BdifthTemplateIfAssignEntry
SEQUENCE
	bdifthTemplateIfAssignInterface	InterfaceIndex
	bdifthTemplateIfAssignOperStatus	INTEGER
	bdifthTemplateIfAssignRowStatus	RowStatus

BdifthIfThresholdFiredEntry
SEQUENCE
	bdifthIfThresholdFiredTemplate	BdifthTemplateIndex
	bdifthIfThresholdsFired	BdifthThresholdList
	bdifthIfLastThresholdFired	BdifthThresholdIndex
	bdifthIfThresholdFiredLstChange	TimeStamp
	bdifthIfThresholdFiredLstSeverity	BdifthThresholdSeverity
	bdifthIfThresholdFiredMaxSeverity	BdifthThresholdSeverity

Defined Values

bdcomIfThresholdMIB		1.3.6.1.4.1.3320.9.218
This MIB module defines the managed objects that support monitoring of thresholds on interfaces. Configuration and monitoring of the thresholds is done through threshold templates that can be assigned to any subset of interfaces on the network element. More than one threshold template can be assigned to a given interface. This MIB module should be used when it is desired to apply a common set of thresholds to a subset of the available interfaces. If a threshold is to be applied to only one interface, then the EVENT-MIB or the RMON-MIB may be used as simpler alternatives. If a threshold is to be applied to all available interfaces, then the EVENT-MIB may be used as a simpler alternative.
MODULE-IDENTITY

bdIfThresholdMIBObjects		1.3.6.1.4.1.3320.9.218.1
OBJECT IDENTIFIER

bdifthTemplateGroup		1.3.6.1.4.1.3320.9.218.1.1
OBJECT IDENTIFIER

bdifthTemplateIfAssignGroup		1.3.6.1.4.1.3320.9.218.1.2
OBJECT IDENTIFIER

bdifthIfThresholdFiredGroup		1.3.6.1.4.1.3320.9.218.1.3
OBJECT IDENTIFIER

bdifthTemplateIndexNext		1.3.6.1.4.1.3320.9.218.1.1.1
This object contains an appropriate value to be used for bdifthTemplateIndex when creating entries in the bdifthTemplateTable. The distinguished value 0 indicates that no unassigned entries are available. To obtain a suggested bdifthTemplateIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. The manager may ignore this object and use alternative mechanisms for choosing an unused value of bdifthTemplateIndex for a new entry. The agent will modify the value to the next unassigned index, when a new entry is created in bdifthTemplateTable with the current value of this object. After deletion of an entry in bdifthTemplateTable the agent will determine through its local policy when its index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	BdifthTemplateIndexOrZero

bdifthTemplateLastChange		1.3.6.1.4.1.3320.9.218.1.1.2
This object specifies the value of sysUpTime at the last time there was either a change to any object in any entry in bdifthTemplateTable, or an entry was created or destroyed in bdifthTemplateTable. If no change to bdifthTemplateTable has occurred since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

bdifthTemplateTable		1.3.6.1.4.1.3320.9.218.1.1.3
This table is used to create threshold templates. Each template includes one or more thresholds (defined in the bdifthThresholdTable), and can be assigned to multiple interfaces. An interface may be associated with more than one template. The assignment of templates to interfaces is done in the bdifthTemplateIfAssignTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BdifthTemplateEntry

bdifthTemplateEntry		1.3.6.1.4.1.3320.9.218.1.1.3.1
An entry describing the general properties of a threshold template. The template is created using the bdifthTemplateRowStatus object. Prior to creating an entry in the table, the manager should obtain a unique value of bdifthTemplateIndex by reading the bdifthTemplateIndexNext object. The values of bdifthTemplateName and bdifthTemplateNotifyHoldDownType must be provided before activating the entry. After creating an entry, thresholds can be defined for the template by creating entries with the same value of bdifthTemplateIndex in the bdifthThresholdTable. The template can then be assigned to one or more interfaces using the bdifthTemplateIfAssignTable. Once an entry has been activated, the value of bdifthTemplateName cannot be modified. In order to use a new value of bdifthTemplateName, a new template must be defined. The values of bdifthTemplateNotifyHoldDownType and bdifthTemplateNotifyHoldDownTime may be modified when the entry is active. See the description clause of bdifthTemplateNotifyHoldDownType for further caveats on modification of that object.
Status: current	Access: not-accessible
OBJECT-TYPE
	BdifthTemplateEntry

bdifthTemplateIndex		1.3.6.1.4.1.3320.9.218.1.1.3.1.1
An arbitrary integer that uniquely identifies a threshold template. The value for each threshold template must remain constant at least from one re-initialization of the agent's network management system to the next re-initialization. The value may change when the agent's network management system is rebooted or re-initialized.
Status: current	Access: not-accessible
OBJECT-TYPE
	BdifthTemplateIndex

bdifthTemplateName		1.3.6.1.4.1.3320.9.218.1.1.3.1.2
This object specifies a unique name associated with the threshold template by the management client, and provides a non-volatile 'handle' for the template. The name must not include whitespace characters. After this value has been written to the startup configuration, the agent must retain the value until a management client deletes it. The level of retention must span reboots and re-initializations of the agent, including those that result in different assignments to the value of bdifthTemplateIndex associated with this template. Once an entry has been activated, this value cannot be modified. In order to use a new value of bdifthTemplateName, a new template must be defined.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

bdifthTemplateNotifyHoldDownType		1.3.6.1.4.1.3320.9.218.1.1.3.1.3
This object specifies the method used to prevent an excess of notifications from being generated when operation fluctuates around a threshold level. The value 'holdDownTimer' indicates that notifications for a given threshold and interface are suppressed for a short amount of time after each notification. The time value is specified in bdifthTemplateNotifyHoldDownTime, which is instantiated only when this object is set to 'holdDownTimer'. After a notification is received for a given threshold and interface, the next notification for that threshold and interface will be generated after at least bdifthTemplateNotifyHoldDownTime amount of time has passed, only when the threshold is next fired or cleared. The value 'fireAndClearThresholds' indicates that hysteresis is used. The management client configures two values for each threshold: one for asserting that the threshold has been exceeded (see bdifthThresholdFiredValue), and a second value for asserting that the threshold is no longer being exceeded (see bdifthThresholdClearedValue, which is instantiated only when this object is set to 'fireAndClearThresholds'). When this entry in bdifthTemplateTable is active, this object may only be modified if there are no active entries in bdifthThresholdTable with the same value of bdifthTemplateIndex.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	other(1), holdDownTimer(2), fireAndClearThresholds(3)

bdifthTemplateNotifyHoldDownTime		1.3.6.1.4.1.3320.9.218.1.1.3.1.4
The minimum amount of time between successive bdifthIfThresholdFired or bdifthIfThresholdCleared notifications for a given interface and template. This object is instantiated only when bdifthTemplateNotifyHoldDownType is set to 'holdDownTimer'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..3600

bdifthTemplateRowStatus		1.3.6.1.4.1.3320.9.218.1.1.3.1.5
This object is used to create and delete threshold templates. The values of bdifthTemplateName and bdifthTemplateNotifyHoldDownType must be provided before activating the entry. An entry can only be deleted when there are no active entries in the bdifthTemplateIfAssignTable with the same value of bdifthTemplateIndex. When an entry is deleted, all associated entries in the bdifthThresholdTable are also deleted. After the entry has been activated, this object cannot be set to any value other than 'destroy'. The row status never changes to 'notInService' after reaching the value 'active'.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

bdifthThresholdLastChange		1.3.6.1.4.1.3320.9.218.1.1.4
This object specifies the value of sysUpTime at the last time there was either a change to any object in any entry in bdifthThresholdTable, or an entry was created or destroyed in bdifthThresholdTable. If no change to bdifthThresholdTable has occurred since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

bdifthThresholdTable		1.3.6.1.4.1.3320.9.218.1.1.5
This table specifies the interface thresholds used in each template.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BdifthThresholdEntry

bdifthThresholdEntry		1.3.6.1.4.1.3320.9.218.1.1.5.1
An entry specifying an interface threshold used in a threshold template. The entry is created using the bdifthThresholdRowStatus object. The values of bdifthThresholdObject, bdifthThresholdSeverity, bdifthThresholdType, and bdifthThresholdFiredValue must be provided before activating the entry. If the value of bdifthTemplateNotifyHoldDownType in the bdifthTemplateEntry with the same value of bdifthTemplateIndex is 'fireAndClearThresholds', then the value of bdifthThresholdClearedValue must also be provided before activating the entry. If the value of bdifthThresholdType is other than 'rateOfIncreaseExponentXIfSpeed', then the value of bdifthThresholdSampleInterval must also be provided before activating the entry. The agent should not allow creation of two entries in the table with the same values of bdifthTemplateIndex, bdifthThresholdObject, bdifthThresholdSeverity, and bdifthThresholdDirection. Once an entry has been activated, the values of bdifthThresholdObject, bdifthThresholdSeverity, bdifthThresholdType, and bdifthThresholdDirection cannot be modified. In order to use new values of these objects, a new threshold must be defined. The values of bdifthThresholdDescr, bdifthThresholdFiredValue, bdifthThresholdClearedValue, bdifthThresholdSampleInterval, and bdifthThresholdApsSwitchover may be modified when the entry is active.
Status: current	Access: not-accessible
OBJECT-TYPE
	BdifthThresholdEntry

bdifthThresholdIndex		1.3.6.1.4.1.3320.9.218.1.1.5.1.1
An arbitrary integer that uniquely identifies a threshold in a threshold template. The value for each threshold must remain constant when the agent's network management system is rebooted or re-initialized.
Status: current	Access: not-accessible
OBJECT-TYPE
	BdifthThresholdIndex

bdifthThresholdDescr		1.3.6.1.4.1.3320.9.218.1.1.5.1.2
A description of the threshold's function and use. The description must not include carriage returns.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..255)

bdifthThresholdObject		1.3.6.1.4.1.3320.9.218.1.1.5.1.3
The object to be compared against the threshold values. The object must be defined in a table indexed only by ifIndex. All of the instance portion of the object identifier is truncated, since the instance(s) to be compared against the threshold are identified using the bdifthTemplateIfAssignTable. If the object has syntax 'Integer32', 'Unsigned32', or 'Gauge32', then bdifthThresholdType should be set to 'absoluteValue'. If the object has syntax 'Counter32' or 'Counter64', then bdifthThresholdType should be set to 'deltaValue' or 'rateOfIncreaseExponentXIfSpeed'.
Status: current	Access: read-create
OBJECT-TYPE
	OBJECT IDENTIFIER

bdifthThresholdSeverity		1.3.6.1.4.1.3320.9.218.1.1.5.1.4
This object specifies the severity associated with the condition when the threshold is exceeded.
Status: current	Access: read-create
OBJECT-TYPE
	BdifthThresholdSeverity

bdifthThresholdType		1.3.6.1.4.1.3320.9.218.1.1.5.1.5
The manner in which to compare bdifthThresholdObject to bdifthThresholdFiredValue and bdifthThresholdClearedValue. The value 'absoluteValue' indicates that the value of bdifthThresholdObject is to be compared directly to bdifthThresholdFiredValue or bdifthThresholdClearedValue. The value 'deltaValue' indicates that the difference between two successive samples of bdifthThresholdObject is to be compared to bdifthThresholdFiredValue or bdifthThresholdClearedValue. The polling interval between successive samples is defined in bdifthThresholdSampleInterval. The value 'rateOfIncreaseExponentXIfSpeed' indicates that the rate of increase of bdifthThresholdObject is to be compared to the negated value of bdifthThresholdFiredValue used as the exponent of 10, times the value of ifSpeed (if the value of ifSpeed is less than the maximum value) or ifHighSpeed (otherwise). For example, a value of bdifthThresholdFiredValue of 5 on a gigabit ethernet interface indicates a threshold of 10^-5 times the interface speed, which is equal to 10,000 per second. When the value of this object is 'rateOfIncreaseExponentXIfSpeed', the polling interval between successive samples is determined automatically by the agent. When the object identified by bdifthThresholdObject is a counter, a threshold type of 'deltaValue' or 'rateOfIncreaseExponentXIfSpeed' should be used. When the object identified by bdifthThresholdObject is not a counter, a threshold type of 'absoluteValue' should be used.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	absoluteValue(1), deltaValue(2), rateOfIncreaseExponentXIfSpeed(3)

bdifthThresholdDirection		1.3.6.1.4.1.3320.9.218.1.1.5.1.6
This object indicates which direction of movement causes the threshold to fire. The value 'rising' indicates that the threshold is fired when the current sampled value is numerically greater than or equal to the value of bdifthThresholdFiredValue, and the threshold was considered to be cleared at the last sampling interval. If the value of the corresponding bdifthTemplateNotifyHoldDownType object is 'fireAndClearThresholds', the threshold is cleared when the current sampled value is less than the value of bdifthThresholdClearedValue, and the threshold was considered to be fired at the last sampling interval. If the value of the corresponding bdifthTemplateNotifyHoldDownType object is other than 'fireAndClearThresholds', the threshold is cleared when the current sampled value is less than the value of bdifthThresholdFiredValue, and the threshold was considered to be fired at the last sampling interval. The value 'falling' indicates that the threshold is fired when the current sampled value is numerically less than or equal to the value of bdifthThresholdFiredValue, and the threshold was considered to be cleared at the last sampling interval. If the value of the corresponding bdifthTemplateNotifyHoldDownType object is 'fireAndClearThresholds', the threshold is cleared when the current sampled value is greater than the value of bdifthThresholdClearedValue, and the threshold was considered to be fired at the last sampling interval. If the value of the corresponding bdifthTemplateNotifyHoldDownType object is other than 'fireAndClearThresholds', the threshold is cleared when the current sampled value is greater than the value of bdifthThresholdFiredValue, and the threshold was considered to be fired at the last sampling interval.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	rising(1), falling(2)

bdifthThresholdFiredValue		1.3.6.1.4.1.3320.9.218.1.1.5.1.7
A threshold value to check against the object identified in bdifthThresholdObject. If the value of bdifthThresholdDirection is 'rising', then the threshold is fired when the current sampled value (absolute, delta, or rate of increase, depending on the value of bdifthThresholdType) of the object identified in bdifthThresholdObject is greater than or equal to this value. If the value of bdifthThresholdDirection is 'falling', then the threshold is fired when the current sampled value (absolute, delta, or rate of increase, depending on the value of bdifthThresholdType) of the object identified in bdifthThresholdObject is less than or equal to this value.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-2147483648..2147483647

bdifthThresholdClearedValue		1.3.6.1.4.1.3320.9.218.1.1.5.1.8
A threshold value to check against the object identified in bdifthThresholdObject. If the value of bdifthThresholdDirection is 'rising', then the threshold is cleared when the current sampled value (absolute, delta, or rate of increase, depending on the value of bdifthThresholdType) of the object identified in bdifthThresholdObject is less than this value. If the value of bdifthThresholdDirection is 'falling', then the threshold is cleared when the current sampled value (absolute, delta, or rate of increase, depending on the value of bdifthThresholdType) of the object identified in bdifthThresholdObject is greater than this value. This object is instantiated only when the value of bdifthTemplateNotifyHoldDownType in the bdifthTemplateEntry with the same value of bdifthTemplateIndex is 'fireAndClearThresholds'.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-2147483648..2147483647

bdifthThresholdSampleInterval		1.3.6.1.4.1.3320.9.218.1.1.5.1.9
The number of milliseconds to wait between samples of the object identified in bdifthThresholdObject. To encourage consistency in sampling, the interval is measured from the beginning of one check to the beginning of the next and the timer is restarted immediately when it expires, not when the check completes. This object is not instantiated when the value of bdifthThresholdType is 'rateOfIncreaseExponentXIfSpeed'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	5..900000

bdifthThresholdApsSwitchover		1.3.6.1.4.1.3320.9.218.1.1.5.1.10
This object indicates whether automatic protection switching (APS) switchover should be triggered, if applicable, when the threshold is fired. The value of this object takes effect when the template identified by bdifthTemplateIndex is assigned to an interface that is part of an APS group. One way to configure an interface in an APS group is using the cApsChanConfigTable in the BDCOM-APS-MIB.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

bdifthThresholdRowStatus		1.3.6.1.4.1.3320.9.218.1.1.5.1.11
This object is used to create and delete thresholds in templates. A new entry can only be created when there is an active entry in the bdifthTemplateTable with the same value of bdifthTemplateIndex. The values of bdifthThresholdObject, bdifthThresholdSeverity, bdifthThresholdType, and bdifthThresholdFiredValue must be provided before activating the entry. If the value of bdifthTemplateNotifyHoldDownType in the bdifthTemplateEntry with the same value of bdifthTemplateIndex is 'fireAndClearThresholds', then the value of bdifthThresholdClearedValue must also be provided before activating the entry. If the value of bdifthThresholdType is other than 'rateOfIncreaseExponentXIfSpeed', then the value of bdifthThresholdSampleInterval must also be provided before activating the entry. When an entry is activated, if there are any entries in bdifthTemplateIfAssignTable with the same value of bdifthTemplateIndex, then the threshold is activated on all interfaces identified in those entries that have instances of the object identified by bdifthThresholdObject. When an entry is destroyed, if there are any entries in bdifthTemplateIfAssignTable with the same value of bdifthTemplateIndex, then the threshold is de-activated on the interfaces identified in those entries. If there are any entries in bdifthIfThresholdFiredTable with bdifthIfThresholdFiredTemplate value equal to this value of bdifthTemplateIndex, then the bit in bdifthIfThresholdsFired corresponding to this threshold is cleared in all such entries. After the entry has been activated, this object cannot be set to any value other than 'destroy'. The row status never changes to 'notInService' after reaching the value 'active'.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

bdifthTemplateIfLastChange		1.3.6.1.4.1.3320.9.218.1.2.1
This object specifies the value of sysUpTime at the last time there was either a change to any object in any entry in bdifthTemplateIfAssignTable, or an entry was created or destroyed in bdifthTemplateIfAssignTable. If no change to bdifthTemplateIfAssignTable has occurred since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

bdifthTemplateIfAssignTable		1.3.6.1.4.1.3320.9.218.1.2.2
This table specifies the assignment of threshold templates to specific interfaces. Each threshold template may be assigned to multiple interfaces. Each interface may have multiple threshold templates assigned to it.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BdifthTemplateIfAssignEntry

bdifthTemplateIfAssignEntry		1.3.6.1.4.1.3320.9.218.1.2.2.1
An entry describing the assignment of a particular threshold template to a particular interface. The entry is created using the bdifthTemplateIfAssignRowStatus object.
Status: current	Access: not-accessible
OBJECT-TYPE
	BdifthTemplateIfAssignEntry

bdifthTemplateIfAssignInterface		1.3.6.1.4.1.3320.9.218.1.2.2.1.1
This object identifies an interface to which the template is assigned.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

bdifthTemplateIfAssignOperStatus		1.3.6.1.4.1.3320.9.218.1.2.2.1.2
This object indicates whether the threshold template identified by bdifthTemplateIndex is operational on the interface identified by bdifthTemplateIfAssignInterface. When the value of this object is 'up', this indicates that the thresholds in this template (identified by bdifthTemplateIndex) are activated on this interface, with the following exception: If a threshold is defined on an object that does not have an instance for this interface, then the threshold is not activated on this interface. If any of the thresholds are being exceeded, then a corresponding entry exists in the bdifthIfThresholdFiredTable. When the value of this object is 'down', this indicates that all thresholds in the template are de-activated on this interface and there is no corresponding entry in the bdifthIfThresholdFiredTable, regardless of whether any of the thresholds in the template are being exceeded on this interface. One reason for a template not to be operational on an interface to which it is assigned is when the interface has two (or more) templates assigned to it that contain thresholds on the same object with the same severity and direction, i.e., thresholds with the same values of bdifthThresholdObject, bdifthThresholdSeverity, and bdifthThresholdDirection. This may occur when a template is assigned to the interface, or when a threshold is added to a template that is already active on the interface. When this occurs, the implementation may operate on both (or all) threshold values, or it may take down one (or more) of the templates on this interface, which is indicated by changing the value of this object from 'up' to 'down'.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

bdifthTemplateIfAssignRowStatus		1.3.6.1.4.1.3320.9.218.1.2.2.1.3
This object is used to create and delete entries in the table, assigning templates to interfaces and removing templates from interfaces, respectively. A new entry can only be created when there is an active entry in the bdifthTemplateTable with the same value of bdifthTemplateIndex. When an entry is activated, the thresholds in this template (identified by bdifthTemplateIndex) are activated on this interface, with the following exception: If a threshold is defined on an object that does not have an instance for this interface, then the threshold is not activated on this interface. When an entry is destroyed, all thresholds in the template are de-activated on this interface and the corresponding entry in the bdifthIfThresholdFiredTable is deleted, if it exists. After the entry has been activated, this object cannot be set to any value other than 'destroy'. The row status never changes to 'notInService' after reaching the value 'active'.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

bdifthThresholdFiredNotifyEnable		1.3.6.1.4.1.3320.9.218.1.3.1
This object specifies the minimum severity threshold governing the generation of bdifthIfThresholdFired and bdifthIfThresholdCleared notifications. For example, if the value of this object is set to 'degrade', then the agent generates these notifications if and only if the severity of the threshold being exceeded is 'degrade' or 'fail'. When the value is other than '0', the generation of bdifthTemplateIfStatusChange notifications is also enabled. The value of '0' disables the generation of all notifications. By default, the value of this object is set to '0'.
Status: current	Access: read-write
OBJECT-TYPE
	BdifthThresholdSeverityOrZero

bdifthThresholdFiredLastChange		1.3.6.1.4.1.3320.9.218.1.3.2
This object specifies the value of sysUpTime at the last time there was either a change to any object in any entry in bdifthIfThresholdFiredTable, or an entry was added or deleted in bdifthIfThresholdFiredTable. If no change to bdifthIfThresholdFiredTable has occurred since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

bdifthIfThresholdFiredTable		1.3.6.1.4.1.3320.9.218.1.3.3
This table indicates the interfaces that currently have threshold fired conditions.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BdifthIfThresholdFiredEntry

bdifthIfThresholdFiredEntry		1.3.6.1.4.1.3320.9.218.1.3.3.1
An entry indicating an interface that currently has one or more threshold fired conditions based on one template.
Status: current	Access: not-accessible
OBJECT-TYPE
	BdifthIfThresholdFiredEntry

bdifthIfThresholdFiredTemplate		1.3.6.1.4.1.3320.9.218.1.3.3.1.1
This object specifies a template for which one or more of the thresholds are fired on this interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	BdifthTemplateIndex

bdifthIfThresholdsFired		1.3.6.1.4.1.3320.9.218.1.3.3.1.2
This object specifies those thresholds that are currently being exceeded on this interface. If a threshold is currently being exceeded (i.e., the threshold is fired) on the interface, then the corresponding bit in the threshold list is set to one. Otherwise, the bit will be set to zero, or the bit will not be present. Only the first N octets are present in the threshold list, such that the highest octet present has at least one bit set to '1'. All higher octets with value '0' are truncated.
Status: current	Access: read-only
OBJECT-TYPE
	BdifthThresholdList

bdifthIfLastThresholdFired		1.3.6.1.4.1.3320.9.218.1.3.3.1.3
This object specifies the last threshold fired or cleared on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	BdifthThresholdIndex

bdifthIfThresholdFiredLstChange		1.3.6.1.4.1.3320.9.218.1.3.3.1.4
This object specifies the value of sysUpTime at the last time a threshold was fired or cleared on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

bdifthIfThresholdFiredLstSeverity		1.3.6.1.4.1.3320.9.218.1.3.3.1.5
This object specifies the severity of the threshold that was last fired or cleared on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	BdifthThresholdSeverity

bdifthIfThresholdFiredMaxSeverity		1.3.6.1.4.1.3320.9.218.1.3.3.1.6
This object specifies the highest severity among the thresholds that are currently being exceeded on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	BdifthThresholdSeverity

bdIfThresholdMIBNotifications		1.3.6.1.4.1.3320.9.218.2
OBJECT IDENTIFIER

bdifthMIBNotificationsPrefix		1.3.6.1.4.1.3320.9.218.2.0
OBJECT IDENTIFIER

bdifthIfThresholdFired		1.3.6.1.4.1.3320.9.218.2.0.1
The agent generates this notification when a threshold defined in a template is asserted on an interface. If a threshold is asserted for a given interface and template, bdifthTemplateNotifyHoldDownTime is set to 'holdDownTimer' for that template, and this notification has recently been sent for the same threshold on the same interface, then this notification may be suppressed.
Status: current	Access: read-only
NOTIFICATION-TYPE

bdifthIfThresholdCleared		1.3.6.1.4.1.3320.9.218.2.0.2
The agent generates this notification when a threshold, that has previously fired, is cleared on an interface. If a threshold is cleared for a given interface and template, bdifthTemplateNotifyHoldDownTime is set to 'holdDownTimer' for that template, and this notification has recently been sent for the same threshold on the same interface, then this notification may be suppressed.
Status: current	Access: read-only
NOTIFICATION-TYPE

bdifthTemplateIfStatusChange		1.3.6.1.4.1.3320.9.218.2.0.3
The agent generates this notification when a template comes up or goes down on an interface to which it is assigned, i.e., when the value of bdifthTemplateIfAssignOperStatus changes. If a template becomes operationally down on an interface upon activation of a new entry in the bdifthTemplateIfAssignTable, the agent generates this notification. The agent need not generate this notification when a new entry in the bdifthTemplateIfAssignTable is activated, if the template becomes operational on the interface. The agent need not generate this notification when an entry in the bdifthTemplateIfAssignTable is destroyed.
Status: current	Access: read-only
NOTIFICATION-TYPE

bdIfThresholdMIBConformance		1.3.6.1.4.1.3320.9.218.3
OBJECT IDENTIFIER

bdIfThresholdMIBCompliances		1.3.6.1.4.1.3320.9.218.3.1
OBJECT IDENTIFIER

bdIfThresholdMIBGroups		1.3.6.1.4.1.3320.9.218.3.2
OBJECT IDENTIFIER

bdIfThresholdMIBCompliance		1.3.6.1.4.1.3320.9.218.3.1.1
The compliance statement for entities that implement the BDCOM Interface Threshold MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

bdIfThresholdTemplateGroup		1.3.6.1.4.1.3320.9.218.3.2.1
A collection of mandatory managed objects for configuration of threshold templates.
Status: current	Access: read-only
OBJECT-GROUP

bdIfThresholdFiredGroup		1.3.6.1.4.1.3320.9.218.3.2.2
A collection of mandatory managed objects for monitoring interfaces where thresholds have been exceeded.
Status: current	Access: read-only
OBJECT-GROUP

bdifthHoldDownTimerGroup		1.3.6.1.4.1.3320.9.218.3.2.3
A collection of managed objects for configuration of a timer-based mechanism for suppression of excess notifications in a short time interval.
Status: current	Access: read-only
OBJECT-GROUP

bdifthHoldDownHysteresisGroup		1.3.6.1.4.1.3320.9.218.3.2.4
A collection of managed objects for configuration of threshold values used to assert that the threshold is no longer being exceeded. These objects are part of the hysteresis mechanism used to prevent excess notifications in a short time interval.
Status: current	Access: read-only
OBJECT-GROUP

bdifthApsGroup		1.3.6.1.4.1.3320.9.218.3.2.5
A collection of managed objects for configuration of APS switchover triggers based on interface thresholds.
Status: current	Access: read-only
OBJECT-GROUP

bdIfThresholdNotifsGroup		1.3.6.1.4.1.3320.9.218.3.2.6
A collection of notifications generated when an interface has a threshold fired or a threshold cleared condition.
Status: current	Access: read-only
NOTIFICATION-GROUP

bdifthTemplateIfNotifsGroup		1.3.6.1.4.1.3320.9.218.3.2.7
A collection of notifications related to the assignment of templates to interfaces.
Status: current	Access: read-only
NOTIFICATION-GROUP

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor