BESTPOWER-MIB

File: BESTPOWER-MIB.mib (61924 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

enterprises IpAddress Gauge
DisplayString OBJECT-TYPE TRAP-TYPE

Defined Types

NonNegativeInteger  
INTEGER    

PositiveInteger  
INTEGER    

UpsConfigScheduleEntry  
SEQUENCE    
  upsConfigScheduleIndex INTEGER
  upsConfigScheduleShutdownDay INTEGER
  upsConfigScheduleShutdownTime DisplayString
  upsConfigScheduleRestartDay INTEGER
  upsConfigScheduleRestartTime DisplayString

UpsConfigTrapsReceiversEntry  
SEQUENCE    
  trapsIndex INTEGER
  trapsReceiverAddr IpAddress
  receiverCommunityString DisplayString
  severityLevel INTEGER
  receiverAccept INTEGER

UpsRegisteredShutdownClientsEntry  
SEQUENCE    
  upsRegisteredShutdownClientsIndex PositiveInteger
  upsRegisteredShutdownClientsIPAddress IpAddress

UpsAlarmEntry  
SEQUENCE    
  upsAlarmIndex PositiveInteger
  upsAlarmName INTEGER
  upsAlarmTime DisplayString

Defined Values

bestPower 1.3.6.1.4.1.2947
OBJECT IDENTIFIER    


upsIdent 1.3.6.1.4.1.2947.1.1
OBJECT IDENTIFIER    

upsBattery 1.3.6.1.4.1.2947.1.2
OBJECT IDENTIFIER    

upsInput 1.3.6.1.4.1.2947.1.3
OBJECT IDENTIFIER    

upsOutput 1.3.6.1.4.1.2947.1.4
OBJECT IDENTIFIER    

upsConfig 1.3.6.1.4.1.2947.1.5
OBJECT IDENTIFIER    

upsControl 1.3.6.1.4.1.2947.1.6
OBJECT IDENTIFIER    

upsTest 1.3.6.1.4.1.2947.1.7
OBJECT IDENTIFIER    

upsAlarm 1.3.6.1.4.1.2947.1.8
OBJECT IDENTIFIER    

upsIdentUpsName 1.3.6.1.4.1.2947.1.1.1
An ID string identifying the Family of UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..19)  

upsIdentModel 1.3.6.1.4.1.2947.1.1.2
The UPS model name (example: 'FE500VA').
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..29)  

upsIdentVARating 1.3.6.1.4.1.2947.1.1.3
The capacity rating of the UPS expressed in VoltAmperes(VA).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

upsIdentUpsType 1.3.6.1.4.1.2947.1.1.4
Type of UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER standby(1), online(2), offline(3), lineInteractive(4), hybrid(5)  

upsIdentUpsSerialNumber 1.3.6.1.4.1.2947.1.1.5
A unique identification number provided by the factory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

upsIdentUpsIdentification 1.3.6.1.4.1.2947.1.1.6
A string entered by the administrator to provide a unique name for the UPS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

upsIdentFirmwareRevision 1.3.6.1.4.1.2947.1.1.7
The firmware revision of the UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..19)  

upsIdentDateOfManufacture 1.3.6.1.4.1.2947.1.1.8
The date when the UPS was manufactured in mm/dd/yyyy format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(6..10)  

upsBatteryStatus 1.3.6.1.4.1.2947.1.2.1
The status of the inverter .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inverterOff(1), inverterOn(2)  

upsBatteryTimeOnBattery 1.3.6.1.4.1.2947.1.2.2
The elapsed time in seconds since the UPS has switched to battery power.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsBatteryRuntimeRemaining 1.3.6.1.4.1.2947.1.2.3
The remaining time in minutes that the UPS will be able to run on battery power.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsBatteryVoltage 1.3.6.1.4.1.2947.1.2.4
The UPS battery voltage expressed in 1/10 VDC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsBatteryCurrent 1.3.6.1.4.1.2947.1.2.5
The battery current expressed in 1/10 ADC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsBatteryTemperature 1.3.6.1.4.1.2947.1.2.6
The internal UPS temperature expressed in 1/10 degree C.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsBatteryLastReplaceDate 1.3.6.1.4.1.2947.1.2.7
The date when the UPS system's batteries were last replaced in mm/dd/yyyy format. When the UPS batteries are replaced, this value should be reset by the administrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(6..10)  

upsInputPhase 1.3.6.1.4.1.2947.1.3.1
The AC input phase.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputFrequency 1.3.6.1.4.1.2947.1.3.2
The utility line frequency in 1/10 Hz.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputVoltage 1.3.6.1.4.1.2947.1.3.3
The utility line voltage in 1/10 VAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputCurrent 1.3.6.1.4.1.2947.1.3.4
The utility line current in 1/10 Ampere AC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputPower 1.3.6.1.4.1.2947.1.3.5
The utility line power in 1/10 Watts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputPhase2 1.3.6.1.4.1.2947.1.3.6
OBJECT IDENTIFIER    

upsInputP2 1.3.6.1.4.1.2947.1.3.6.1
The AC input phase.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputFrequency2 1.3.6.1.4.1.2947.1.3.6.2
The utility line frequency in 1/10 Hz.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputVoltage2 1.3.6.1.4.1.2947.1.3.6.3
The utility line voltage in 1/10 VAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputCurrent2 1.3.6.1.4.1.2947.1.3.6.4
The utility line current in 1/10 Ampere AC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputPower2 1.3.6.1.4.1.2947.1.3.6.5
The utility line power in 1/10 Watts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputPhase3 1.3.6.1.4.1.2947.1.3.7
OBJECT IDENTIFIER    

upsInputP3 1.3.6.1.4.1.2947.1.3.7.1
The AC input phase.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputFrequency3 1.3.6.1.4.1.2947.1.3.7.2
The utility line frequency in 1/10 Hz.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputVoltage3 1.3.6.1.4.1.2947.1.3.7.3
The utility line voltage in 1/10 VAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputCurrent3 1.3.6.1.4.1.2947.1.3.7.4
The utility line current in 1/10 Ampere AC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsInputPower3 1.3.6.1.4.1.2947.1.3.7.5
The utility line power in 1/10 Watts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputStatus 1.3.6.1.4.1.2947.1.4.1
The current state of the UPS. If the UPS is unable to determine its state, this variable is set to unknown(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), onLine(2), onBattery(3), onBypass(4)  

upsOutputPhase 1.3.6.1.4.1.2947.1.4.2
The output phase.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputFrequency 1.3.6.1.4.1.2947.1.4.3
The output frequency of the UPS expressed in 1/10 Hz.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputVoltage 1.3.6.1.4.1.2947.1.4.4
The output voltage of the UPS expressed in 1/10 VAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputCurrent 1.3.6.1.4.1.2947.1.4.5
The output current of the UPS expressed in 1/10 AC Amperes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputTruePower 1.3.6.1.4.1.2947.1.4.6
The true output power of the UPS expressed in 1/10 Watts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputApparentPower 1.3.6.1.4.1.2947.1.4.7
The apparent output power of the UPS expressed in 1/10 VoltAmperes(VA).
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputPowerFactor 1.3.6.1.4.1.2947.1.4.8
The output powerfactor of the UPS expressed in +/- 1/10 units deviating from 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputPercentLoad 1.3.6.1.4.1.2947.1.4.9
The percentage of the total UPS power capacity being used expressed in % of 100.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputPhase2 1.3.6.1.4.1.2947.1.4.10
OBJECT IDENTIFIER    

upsOutputP2 1.3.6.1.4.1.2947.1.4.10.1
The output phase.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputFrequency2 1.3.6.1.4.1.2947.1.4.10.2
The output frequency of the UPS expressed in 1/10 Hz.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputVoltage2 1.3.6.1.4.1.2947.1.4.10.3
The output voltage of the UPS expressed in 1/10 VAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputCurrent2 1.3.6.1.4.1.2947.1.4.10.4
The output current of the UPS expressed in 1/10 AC Amperes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputTruePower2 1.3.6.1.4.1.2947.1.4.10.5
The true output power of the UPS expressed in 1/10 Watts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputApparentPower2 1.3.6.1.4.1.2947.1.4.10.6
The apparent output power of the UPS expressed in 1/10 VoltAmperes(VA).
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputPowerFactor2 1.3.6.1.4.1.2947.1.4.10.7
The output powerfactor of the UPS expressed in +\- 1/10 units deviating from 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputPhase3 1.3.6.1.4.1.2947.1.4.11
OBJECT IDENTIFIER    

upsOutputP3 1.3.6.1.4.1.2947.1.4.11.1
The output phase.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputFrequency3 1.3.6.1.4.1.2947.1.4.11.2
The output frequency of the UPS expressed in 1/10 Hz.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputVoltage3 1.3.6.1.4.1.2947.1.4.11.3
The output voltage of the UPS expressed in 1/10 VAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputCurrent3 1.3.6.1.4.1.2947.1.4.11.4
The output current of the UPS expressed in 1/10 AC Amperes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputTruePower3 1.3.6.1.4.1.2947.1.4.11.5
The true output power of the UPS expressed in 1/10 Watts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputApparentPower3 1.3.6.1.4.1.2947.1.4.11.6
The apparent output power of the UPS expressed in 1/10 VoltAmperes = (VA).
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputPowerFactor3 1.3.6.1.4.1.2947.1.4.11.7
The output powerfactor of the UPS expressed in +/- 1/10 units deviating from 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsConfigLowRuntimeSetpoint 1.3.6.1.4.1.2947.1.5.1
This setpoint controls when the UPS will initiate a Low Runtime Alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

upsConfigDelayBeforeRestart 1.3.6.1.4.1.2947.1.5.2
The delay in seconds after utility line power returns before the UPS will turn on. This value is used in conjunction with TurnUPSOff, RebootUPS, and the Scheduled Shutdown objects.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

upsConfigDelayBeforeShutdown 1.3.6.1.4.1.2947.1.5.3
The delay in seconds that the UPS waits before executing an off command upon request of an external device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

upsConfigTest 1.3.6.1.4.1.2947.1.5.4
OBJECT IDENTIFIER    

upsConfigTestLevel 1.3.6.1.4.1.2947.1.5.4.1
This is the level of the System Test.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), logic(2), inverter(3), battery(4)  

upsConfigDaysBetweenTests 1.3.6.1.4.1.2947.1.5.4.3
The number of days between Tests.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..366  

upsConfigBatteryTestDuration 1.3.6.1.4.1.2947.1.5.4.4
The number of seconds the UPS must run on battery power during a battery test.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..9999  

upsConfigScheduleTable 1.3.6.1.4.1.2947.1.5.5
The table to schedule shutting down the ups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UpsConfigScheduleEntry

upsConfigScheduleEntry 1.3.6.1.4.1.2947.1.5.5.1
The entries for each day.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  UpsConfigScheduleEntry  

upsConfigScheduleIndex 1.3.6.1.4.1.2947.1.5.5.1.1
The index of scheduled events.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsConfigScheduleShutdownDay 1.3.6.1.4.1.2947.1.5.5.1.2
The weekday on which the UPS should shut down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7), none(8)  

upsConfigScheduleShutdownTime 1.3.6.1.4.1.2947.1.5.5.1.3
The time that the process of shutting down the UPS will be initiated
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

upsConfigScheduleRestartDay 1.3.6.1.4.1.2947.1.5.5.1.4
The weekday on which the UPS should restart
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7), none(8)  

upsConfigScheduleRestartTime 1.3.6.1.4.1.2947.1.5.5.1.5
The time the UPS will restart in hh:mm:ss format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  


bestLinkHistoryLogFrequency 1.3.6.1.4.1.2947.1.5.8.1
The frequency of updating the history log in minutes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

bestLinkRefreshFrequency 1.3.6.1.4.1.2947.1.5.8.2
The frequency of saving configuration,history and event log data in non-volatile memory. If the value is set to 0, then saving data is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

bestLinkNetId 1.3.6.1.4.1.2947.1.5.8.3
The IP address of the device. Setting this parameter causes BestLink to reboot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

bestLinkGateway 1.3.6.1.4.1.2947.1.5.8.4
The gateway address for the network BestLink is connected to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

bestLinkNetMask 1.3.6.1.4.1.2947.1.5.8.5
The net mask of the device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

bestLinkSysDate 1.3.6.1.4.1.2947.1.5.8.6
The system date of the device. The date is in mm/dd/yyyy format. The range of system date is from 1/1/1980 to 12/31/2037.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(6..10)  

bestLinkSysTime 1.3.6.1.4.1.2947.1.5.8.7
The system time of the device. The time is in hh:mm:ss format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(5..8)  

bestLinkTftpFileName 1.3.6.1.4.1.2947.1.5.8.8
The tftp file name that contains the software upgrade image.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..59)  

bestLinkTftpHost 1.3.6.1.4.1.2947.1.5.8.9
The tftp host IP address from where to get the image.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

bestLinkFlashEEPROM 1.3.6.1.4.1.2947.1.5.8.10
Saves the history log, eventlog, and configuration data to non-volatile memory.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bestLinkPrimaryTimeServer 1.3.6.1.4.1.2947.1.5.8.11
The primary time server is responsible for sending the correct time to the UPS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

bestLinkSecondaryTimeServer 1.3.6.1.4.1.2947.1.5.8.12
The secondary time server responsible for sending the correct time to the UPS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

bestLinkSoftwareVersion 1.3.6.1.4.1.2947.1.5.8.13
The version of BestLink software.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

upsConfigTrapsReceivers 1.3.6.1.4.1.2947.1.5.9
OBJECT IDENTIFIER    

upsConfigTrapsReceiversTable 1.3.6.1.4.1.2947.1.5.9.1
A list of managers to send traps to.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UpsConfigTrapsReceiversEntry

upsConfigTrapsReceiversEntry 1.3.6.1.4.1.2947.1.5.9.1.1
The managers to send traps to.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  UpsConfigTrapsReceiversEntry  

trapsIndex 1.3.6.1.4.1.2947.1.5.9.1.1.1
The index to a trap receiver entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

trapsReceiverAddr 1.3.6.1.4.1.2947.1.5.9.1.1.2
The IP address of the manager to send a trap to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

receiverCommunityString 1.3.6.1.4.1.2947.1.5.9.1.1.3
The community name to use in the trap when sent to the manager.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..19)  

severityLevel 1.3.6.1.4.1.2947.1.5.9.1.1.4
The severity threshold of traps to send to the manager. Traps are labeled by severity as informational(1), warning(2), severe(3). Only traps of equal or greater severity than this value are sent to the manager.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER information(1), warning(2), severe(3)  

receiverAccept 1.3.6.1.4.1.2947.1.5.9.1.1.5
An entry will become active if yes, otherwise it will be disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

upsConfigRegisteredShutdownClients 1.3.6.1.4.1.2947.1.5.10
OBJECT IDENTIFIER    

upsRegisteredShutdownClientsTable 1.3.6.1.4.1.2947.1.5.10.1
A list of registered shutdown client table entries. The table contains zero, one, or many rows at any moment, depending upon the number of Netwatch clients registered with BestLink
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UpsRegisteredShutdownClientsEntry

upsRegisteredShutdownClientsEntry 1.3.6.1.4.1.2947.1.5.10.1.1
An entry containing information applicable to a particular registered shutdown client.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  UpsRegisteredShutdownClientsEntry  

upsRegisteredShutdownClientsIndex 1.3.6.1.4.1.2947.1.5.10.1.1.1
An index of alarm entries in the RegisteredShutdownClientsTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PositiveInteger  

upsRegisteredShutdownClientsIPAddress 1.3.6.1.4.1.2947.1.5.10.1.1.2
The IP Address of the registered shutdown client
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

upsRegisteredShutdownClientsTotalNumberOf 1.3.6.1.4.1.2947.1.5.10.2
The total number of registered shutdown clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsControlTurnOffUPS 1.3.6.1.4.1.2947.1.6.1
Setting this variable to UpsOff(2) causes the UPS to shut off. When the UPS is in the off state, the UPS will remain off until the ON/OFF switch is manually toggled. Setting this variable to cancelUpsOff(1) allows for a method to cancel the upsOff(2) command to the UPS that is still pending, or will make an attempt to restart a UPS that has been shutdown, provided that BestLink is powered by some other means. Setting this variable to rebootUps(3) causes the UPS to shut off and turn back on. Setting this variable to cancelrebootUps(4) allows for a method to cancel the rebootUps(3) command to the UPS that is still pending, or will make an attempt to restart a UPS that has been shutdown, provided that BestLink is powered by some other means.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER cancelUpsOff(1), upsOff(2), rebootUps(3), cancelrebootUps(7)  

upsControlActivateUpsScheduling 1.3.6.1.4.1.2947.1.6.4
Setting this variable to On(2) causes the UPS to activate the scheduling parameters that have been previously configured within the upsConfigDailyShutdownScheduleTable and the upsConfigWeeklyShutdownScheduleTable. Setting this variable to Off(1) suspends all currently configured schedules.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), on(2)  

upsManualTests 1.3.6.1.4.1.2947.1.7.1
Setting this variable to any value other than (1) causes the UPS to perform a manual test or abort a particular test in progress.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noTestInitiated(1), initiateManualBeeperTest(2), initiateManualSystemTest(3), initiateManualInverterTest(4), initiateManualBatteryTest(5), abortManualBeeperTest(6), abortManualSystemTest(7), abortManualInverterTest(8), abortManualBatteryTest(9)  

upsAlarmsPresent 1.3.6.1.4.1.2947.1.8.1
The present number of active alarm conditions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

upsLastKnownAlarm 1.3.6.1.4.1.2947.1.8.2
A unique identifier for an alarm condition. This value must remain constant. Value 'noAlarm(37)' will be returned if no Alarm has occured till the point of GET operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER onBattery(1), lowRuntime(2), nearLowBattery(3), lowBattery(4), highBattery(5), checkBattery(6), replaceBattery(7), checkInverter(8), batteriesDisconnected(9), outputOverload(10), lowAcOut(11), circuitBreakerWarning(12), circuitBreakerShdn(13), bypassOn(14), autoBypass(15), siteWiringFault(16), checkFan(17), highAmbTemp(18), highHSTemp(19), highXFMRTemp(20), highPFMTemp(21), probeMissing(22), checkPowerSupply(23), tapRegulator(24), relayFailure(25), checkFuse(26), checkMOV(27), memoryError(28), callService(29), upsFailed(30), userTest(31), testInProgress(32), diagnosticTestFailed(33), ePO(34), upsOff(35), communicationsLost(36), noAlarm(37)  

upsAlarmTable 1.3.6.1.4.1.2947.1.8.3
A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmIndex equal to 1, and increments the value of upsAlarmIndex each time a new row is created.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UpsAlarmEntry

upsAlarmEntry 1.3.6.1.4.1.2947.1.8.3.1
An entry containing information applicable to a particular alarm.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  UpsAlarmEntry  

upsAlarmIndex 1.3.6.1.4.1.2947.1.8.3.1.1
An index of alarm entries in the alarm log.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PositiveInteger  

upsAlarmName 1.3.6.1.4.1.2947.1.8.3.1.2
A unique identifier for an alarm condition. This value must remain constant.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER onBattery(1), lowRuntime(2), nearLowBattery(3), lowBattery(4), highBattery(5), checkBattery(6), replaceBattery(7), checkInverter(8), batteriesDisconnected(9), outputOverload(10), lowAcOut(11), circuitBreakerWarning(12), circuitBreakerShdn(13), bypassOn(14), autoBypass(15), siteWiringFault(16), checkFan(17), highAmbTemp(18), highHSTemp(19), highXFMRTemp(20), highPFMTemp(21), probeMissing(22), checkPowerSupply(23), tapRegulator(24), relayFailure(25), checkFuse(26), checkMOV(27), memoryError(28), callService(29), upsFailed(30), userTest(31), testInProgress(32), diagnosticTestFailed(33), ePO(34), upsOff(35), communicationsLost(36)  

upsAlarmTime 1.3.6.1.4.1.2947.1.8.3.1.3
The time that the alarm occurred in hh:mm:ss format.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

upsWellKnownAlarms 1.3.6.1.4.1.2947.1.8.4
OBJECT IDENTIFIER    

upsAlarmOnBattery 1.3.6.1.4.1.2947.1.8.4.1
The UPS is drawing power from the batteries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmLowRuntime 1.3.6.1.4.1.2947.1.8.4.2
The remaining battery runtime is less than or equal to the upsConfigLowRuntimeSetpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmNearLowBattery 1.3.6.1.4.1.2947.1.8.4.3
The battery voltage on the UPS has reached a value where the inverter will not be able to function very much longer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmLowBattery 1.3.6.1.4.1.2947.1.8.4.4
The battery voltage on the UPS has reached a value where the inverter has stopped providing output power to the connected load equipment. The UPS has shutdown to protect the batteries from complete discharge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmHighBattery 1.3.6.1.4.1.2947.1.8.4.5
The battery charger voltage on the UPS has reached a value that is too high for safe battery maintenance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmCheckBattery 1.3.6.1.4.1.2947.1.8.4.6
The periodic battery test has failed. A manual test of the batteries needs to be performed to determine which battery\batteries need replaced.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmReplaceBattery 1.3.6.1.4.1.2947.1.8.4.7
One or more batteries have been determined to require replacement. Compatibility: Fortress II
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmCheckInverter 1.3.6.1.4.1.2947.1.8.4.8
The inverter has failed the automatic system test.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmBatteriesDisconnected 1.3.6.1.4.1.2947.1.8.4.9
The UPS has detected that the DC voltage needed to start up is too low or missing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmOutputOverload 1.3.6.1.4.1.2947.1.8.4.10
The output load exceeds the UPS output capacity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmLowAcOut 1.3.6.1.4.1.2947.1.8.4.11
The output load has exceeded the UPS output capacity, and the UPS has shut down.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmCircuitBreakerWarning 1.3.6.1.4.1.2947.1.8.4.12
To much load equipment has been connected to the UPS and has has caused excess current draw from the output.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmCircuitBreakerShdn 1.3.6.1.4.1.2947.1.8.4.13
The UPS has shut down due to an extended excess of current draw from the output.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmBypassOn 1.3.6.1.4.1.2947.1.8.4.14
The Bypass is presently engaged on the UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmAutoBypass 1.3.6.1.4.1.2947.1.8.4.15
The UPS has gone into the Auto Bypass mode to redirect power around the UPS circuitry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmSiteWiringFault 1.3.6.1.4.1.2947.1.8.4.16
The UPS has found a problem in your wall outlet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmCheckFan 1.3.6.1.4.1.2947.1.8.4.17
The fan on the UPS has stopped
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmHighAmbTemp 1.3.6.1.4.1.2947.1.8.4.18
The internal temperature inside the UPS is too hot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmHighHSTemp 1.3.6.1.4.1.2947.1.8.4.19
The Inverter heatsink assembly inside the UPS is to hot .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmHighXFMRTemp 1.3.6.1.4.1.2947.1.8.4.20
The temperature of the main transformer inside the UPS is too hot .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmHighPFMTemp 1.3.6.1.4.1.2947.1.8.4.21
The temperature of the PFM module inside the UPS is too hot .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmProbeMissing 1.3.6.1.4.1.2947.1.8.4.22
One or all of the sense probes has been disconnected on the UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmCheckPowerSupply 1.3.6.1.4.1.2947.1.8.4.23
The internal DC supply voltages are attenuated or missing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmTapRegulator 1.3.6.1.4.1.2947.1.8.4.24
The UPS detected a possible failure in the tap changer (open or welded relay, etc.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmRelayFailure 1.3.6.1.4.1.2947.1.8.4.25
There is a hardware problem inside the UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmCheckFuse 1.3.6.1.4.1.2947.1.8.4.26
The failure of one or more fuses has been detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmCheckMOV 1.3.6.1.4.1.2947.1.8.4.27
One or more MOVs have failed due to a voltage surge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmMemoryError 1.3.6.1.4.1.2947.1.8.4.28
The UPS has lost the programmed settings in the memory of the logic board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmCallService 1.3.6.1.4.1.2947.1.8.4.29
A hardware malfunction has occurred inside the UPS. Please consult a factory authorized service representative for assistance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmupsFailed 1.3.6.1.4.1.2947.1.8.4.30
A general fault in the UPS has been detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmUserTest 1.3.6.1.4.1.2947.1.8.4.31
A user test of the alarm beeper is in progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmTestInProgress 1.3.6.1.4.1.2947.1.8.4.32
A test is in progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmDiagnosticTestFailed 1.3.6.1.4.1.2947.1.8.4.33
The result of the last diagnostic test indicates a failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmEPO 1.3.6.1.4.1.2947.1.8.4.34
The Emergency Power OFF feature has been activiated at the RS-232 port on the UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmUpsOff 1.3.6.1.4.1.2947.1.8.4.35
The output of the UPS is in the off state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmCommunicationsLost 1.3.6.1.4.1.2947.1.8.4.36
A problem has been encountered in the communications between the agent and the UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsTrapPowerFail 1
WARNING: Utility power not available.
TRAP-TYPE    

upsTrapPowerRestored 2
INFORMATION: Utility power has been restored.
TRAP-TYPE    

upsTrapUPSOnBattery 3
WARNING: The UPS has switched to battery backup power.
TRAP-TYPE    

upsTrapUPSNotOnBattery 4
INFORMATION: The UPS is not on battery power.
TRAP-TYPE    

upsTrapLowRuntime 5
SEVERE: The runtime remaining on battery power is very short, and the UPS will soon shut down.
TRAP-TYPE    

upsTrapUPSCanRunOnBattery 6
INFORMATION: The UPS has returned from a low runtime condition.
TRAP-TYPE    

upsTrapNearLowBattery 7
SEVERE: The UPS batteries are low and will soon be exhausted. If utility power is not restored the UPS will put itself to 'sleep' and immediately cut power to the load.
TRAP-TYPE    

upsTrapHighBattery 8
WARNING: The battery charger voltage on the UPS has reached a value that is too high for safe battery maintenance.
TRAP-TYPE    

upsTrapBatteryOK 9
INFORMATION: The UPS has returned from a near low or high battery condition.
TRAP-TYPE    

upsTrapLowBattery 10
SEVERE: The UPS will run for approximately 2 minutes more and then put itself to sleep to prevent a complete discharge of the batteries.
TRAP-TYPE    

upsTrapCheckBattery 11
SEVERE: The UPS has failed a scheduled or manual battery test.
TRAP-TYPE    

upsTrapReplaceBattery 12
SEVERE: One or more UPS batteries need to be replaced.
TRAP-TYPE    

upsTrapCheckInverter 13
SEVERE: The UPS has failed a scheduled or manual inverter test.
TRAP-TYPE    

upsTrapBatteriesDisconnected 14
WARNING: The UPS battery voltage is either too low or missing to start up.
TRAP-TYPE    

upsTrapOutputOverload 15
WARNING: The output load exceeds the UPS output capacity.
TRAP-TYPE    

upsTrapUPSNoLongerOverloaded 16
INFORMATION: The UPS has returned from an output overload condition.
TRAP-TYPE    

upsTrapLowAcOut 17
SEVERE: The output load has exceeded the UPS output capacity, and the UPS has shut down.
TRAP-TYPE    

upsTrapCircuitBreakerWarning 18
SEVERE: To much load equipment has been connected to the UPS and has has caused excess current draw from the output.
TRAP-TYPE    

upsTrapCircuitBreakerOK 19
INFORMATION: The UPS has returned from a circuit breaker warning condition.
TRAP-TYPE    

upsTrapCircuitBreakerShdn 20
SEVERE: The UPS has shut down due to an extended excess of current draw from the output.
TRAP-TYPE    

upsTrapBypassOn 21
SEVERE: The Bypass is presently engaged on the UPS.
TRAP-TYPE    

upsTrapUPSOnline 22
INFORMATION: The UPS has returned from an on bypass condition.
TRAP-TYPE    

upsTrapSiteWiringFault 23
SEVERE: The UPS has found a problem in your wall outlet.
TRAP-TYPE    

upsTrapCheckFan 24
SEVERE: The fan on the UPS has stopped .
TRAP-TYPE    

upsTrapHighUPSTemp 25
SEVERE: The internal temperature inside the UPS is too hot.
TRAP-TYPE    

upsTrapTempOK 26
INFORMATION: The UPS has returned from a high ambient temp condition.
TRAP-TYPE    

upsTrapHighHSTemp 27
SEVERE: The Inverter heatsink assembly inside the UPS is too hot .
TRAP-TYPE    

upsTrapHSTempOK 28
INFORMATION: The UPS has returned from a high heatsink temp condition.
TRAP-TYPE    

upsTrapHighXFMRTemp 29
SEVERE: The temperature of the main transformer inside the UPS is too hot .
TRAP-TYPE    

upsTrapHighPFMTemp 30
SEVERE: The temperature of the PFM module inside the UPS is too hot.
TRAP-TYPE    

upsTrapProbeMissing 31
SEVERE: One or all of the temperature probes has been disconnected on the UPS.
TRAP-TYPE    

upsTrapProbeReconnected 32
INFORMATION: The UPS has returned from a probe missing condition.
TRAP-TYPE    

upsTrapCheckPowerSupply 33
SEVERE: The internal DC supply voltages are attenuated or missing.
TRAP-TYPE    

upsTrapTapRegulatorFault 34
SEVERE: The UPS detected a possible failure in the tap changer (open or welded relay, etc.)
TRAP-TYPE    

upsTrapRelayFailure 35
SEVERE: There is a hardware problem inside the UPS.
TRAP-TYPE    

upsTrapCheckFuse 36
SEVERE: The failure of one or more fuses has been detected.
TRAP-TYPE    

upsTrapCheckMOV 37
SEVERE: One or more MOVs have failed due to a voltage surge.
TRAP-TYPE    

upsTrapMemoryError 38
SEVERE: The UPS has lost the programmed settings in the memory of the logic board.
TRAP-TYPE    

upsTrapCallService 39
SEVERE: A hardware malfunction has occurred inside the UPS. Please consult a factory authorized service representative for assistance.
TRAP-TYPE    

upsTrapManualAlarmBeeperTestInitiated 40
INFORMATION: A manual test of the alarm beeper is being performed on the UPS.
TRAP-TYPE    

upsTrapManualAlarmBeeperTestAborted 41
INFORMATION: The test of UPS has completed.
TRAP-TYPE    

upsTrapScheduledTestInProgress 42
INFORMATION: A test is in progress.
TRAP-TYPE    

upsTrapScheduledTestFailed 43
SEVERE: The last test performed failed.
TRAP-TYPE    

upsTrapCommunicationLost 44
SEVERE: Communication to the UPS has been lost. Steps to reestablish communication are in progress.
TRAP-TYPE    

upsTrapCommunicationRestored 45
INFORMATION: Communication with the UPS has been restored.
TRAP-TYPE    

upsTrapUPSGoingDown 46
WARNING: The ups has been given shutdown command by the management station.
TRAP-TYPE    

upsTrapUPSTurnedOff 47
INFORMATION: The ups has been turned off by the management station.
TRAP-TYPE    

upsTrapUPSSleeping 48
INFORMATION: The UPS has entered in 'sleep' mode. Power to the load has been cut off.
TRAP-TYPE    

upsTrapUPSWokeUp 49
INFORMATION: The UPS woke up from 'sleep' mode. Power to the load has been restored.
TRAP-TYPE    

upsTrapUPSRebooted 50
INFORMATION: The UPS is rebooted.
TRAP-TYPE    

upsTrapEmergencyPowerOFF 51
SEVERE: The Emergency Power OFF feature has been activiated at the RS-232 port on the UPS.
TRAP-TYPE    

upsTrapHistLogWarn 52
WARNING: The ups history log buffer is almost full.
TRAP-TYPE    

upsTrapEventLogWarn 53
WARNING: The ups event log buffer is almost full.
TRAP-TYPE    

upsTrapUPSFail 54
SEVERE: A critical fault has been detected inside the UPS. Power to the load has been shut off.
TRAP-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor