BREEZECOM-MIB

Imported modules

Imported symbols

enterprises	IpAddress	OBJECT-TYPE
Counter	DisplayString	TRAP-TYPE

Defined Types

MacAddress
OCTET STRING	Size(6)

TrapHostsEntry
SEQUENCE
	trapHostsIndex	INTEGER
	trapIPaddress	IpAddress
	trapCommunity	DisplayString

KnownAPsEntry
SEQUENCE
	knownAPsIndex	INTEGER
	knownAPsValue	MacAddress
	knownAPsQuality	INTEGER
	knownAPsAvrgRssi	INTEGER
	knownAPsStatus	INTEGER
	knownAPsLoadStations	INTEGER
	knownAPsGoodBeacons	INTEGER
	knownAPsTotalBeacons	INTEGER
	knownAPsAvrgDbm	DisplayString	Size(10)

AdbEntry
SEQUENCE
	stAddress	MacAddress
	stType	INTEGER
	stCFMode	INTEGER
	stMaxRate	INTEGER
	stCurTxRate	INTEGER
	stRssi	INTEGER
	stPMMode	INTEGER
	stTxFragments	Counter
	stTxRetry	Counter
	stTxRetryPercent	Counter
	stTxFragments1M	Counter
	stReTxFragments1M	Counter
	stTxFragments2M	Counter
	stReTxFragments2M	Counter
	stTxFragments3M	Counter
	stReTxFragments3M	Counter
	stTxDroppedPackets	Counter
	stRxFragments	Counter
	stWlanStatus	INTEGER
	stResetCounters	INTEGER
	stDbm	DisplayString	Size(30)

FreqStatisticsEntry
SEQUENCE
	freqStatisticsIndex	INTEGER
	freqNo	INTEGER
	freqTotalReceived	Counter

PowreStationsEntry
SEQUENCE
	powerSaveIndex	INTEGER
	powerSaveStationID	INTEGER
	powerSaveBuffered	INTEGER
	powerSaveAged	INTEGER
	powerSaveSent	INTEGER
	powerSaveQueueFull	INTEGER

Defined Values

breezecom		1.3.6.1.4.1.710
OBJECT IDENTIFIER

breezecomPrvRev		1.3.6.1.4.1.710.3
OBJECT IDENTIFIER

breezecomOID		1.3.6.1.4.1.710.4
OBJECT IDENTIFIER

breezecomAP10		1.3.6.1.4.1.710.4.1
OBJECT IDENTIFIER

breezecomWB10		1.3.6.1.4.1.710.4.2
OBJECT IDENTIFIER

breezecomSA10		1.3.6.1.4.1.710.4.3
OBJECT IDENTIFIER

breezecomSA40		1.3.6.1.4.1.710.4.4
OBJECT IDENTIFIER

brznetmib		1.3.6.1.4.1.710.3.2
OBJECT IDENTIFIER

brzSys		1.3.6.1.4.1.710.3.2.1
OBJECT IDENTIFIER

sysCmd		1.3.6.1.4.1.710.3.2.1.1
OBJECT IDENTIFIER

sysReset		1.3.6.1.4.1.710.3.2.1.1.1
Setting the value of this attribute to ON is interpreted as a reset command for the system.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

sysSetDefaults		1.3.6.1.4.1.710.3.2.1.1.2
Setting the value of this attribute to ON will cause the system to set the NVRAM parameters to the factory default values. These values will become active after the next system reset
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

sysResetCounters		1.3.6.1.4.1.710.3.2.1.1.3
Setting the value of this attribute to ON will cause the system to clear the performance counters.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

sysTrapEnable		1.3.6.1.4.1.710.3.2.1.1.4
Setting the value of this attribute to OFF will disable the system from sending TRAPs.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

sysTrapCounter		1.3.6.1.4.1.710.3.2.1.1.5
This attribute counts the total number of traps generated by the device, since initialization.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

sysCarrierSense		1.3.6.1.4.1.710.3.2.1.1.6
This attribute defines the carrier sense absolute threshold
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

sysDeltaCarrierSense		1.3.6.1.4.1.710.3.2.1.1.7
This attribute defines the carrier sense differential threshold
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

sysPartialDefaults		1.3.6.1.4.1.710.3.2.1.1.8
Setting the value of this attribute to ON will cause the system to set the partial NVRAM parameters to the factory default values. These values will become active after the next system reset
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

sysRunFromNonActiveCode		1.3.6.1.4.1.710.3.2.1.1.9
This attribute make you run from non active code. Automatic switch is done if the non active code is valid. To activate set to On. If the switch succeed no response will be sent to the SNMP browser.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), on(1)

accessRights		1.3.6.1.4.1.710.3.2.1.1.10
OBJECT IDENTIFIER

sysNoiseFloor		1.3.6.1.4.1.710.3.2.1.1.11
This attribute defines the low RSSI threshold in DBM units. Allowed range is from -120 to -50 dbm.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

sysExternalAmplifier		1.3.6.1.4.1.710.3.2.1.1.12
This attribute is set to 1 when external amplifier is connected to the device and set to 0 when device is connected to anntena.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(0)

sysDisplayAccessRights		1.3.6.1.4.1.710.3.2.1.1.10.1
This attribute Display the access rights of that station.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	user(0), installer(1), authorized-technician(2)

sysChangeRightsToUSER		1.3.6.1.4.1.710.3.2.1.1.10.2
This attribute let you change the access rights of that station to USER.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	unchanged(0), change(1)

sysChangeRightsToINSTALLER		1.3.6.1.4.1.710.3.2.1.1.10.3
This attribute let you change the access rights of that station to INSTALLER. Type the Installer password for the desired access right.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(15)

sysChangeRightsToTECHNICIAN		1.3.6.1.4.1.710.3.2.1.1.10.4
This attribute let you change the access rights of that station to AUTHORIZED TECHNICIAN. Type the Technician password for the desired access right.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(20)

sysChangeInstallerPassword		1.3.6.1.4.1.710.3.2.1.1.10.5
This attribute let you change the Installer Password of that station. Type the new password, maximum 8 characters.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(9)

sysParams		1.3.6.1.4.1.710.3.2.1.2
OBJECT IDENTIFIER

brzHWMacAddress		1.3.6.1.4.1.710.3.2.1.2.1
The Hardware MAC address of the device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

brzApplTunneling		1.3.6.1.4.1.710.3.2.1.2.2
This attribute specifies the device tunneling mode, as follows: ipx - The device will enable IPX tunneling only. apple-talk - The device will enable AppleTalk tunneling only. none - The device will disable tunneling. both - The device will enable only IPX and AppleTalk tunneling.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ipx(0), both(1), none(2), apple-talk(3)

brzPositiveBrg		1.3.6.1.4.1.710.3.2.1.2.3
This attribute specifies the Wired to Wireless LAN bridging mode at the AP, as follows: reject-unknown - The AP forwards to the Wireless LAN only frames that are destined to associated stations. forward-unknown - The AP forwards to the Wireless LAN frames destined to associated AND unknown addresses. This value should be used only for Wireless Bridge installations. intelligent - If connected to a wireless bridge, the AP automatically activates the Forward-Unknown option. na - A not applicable value, for non-AP devices.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	reject-unknown(1), forward-unknown(2), intelligent(3), na(255)

brzIpFilter		1.3.6.1.4.1.710.3.2.1.2.4
Setting the value of this attribute to ON will cause the system to filter all non-IP traffic to the Wireless LAN. This should be used on environments where only IP (and ARP) traffic is permitted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), na(255)

brzTranslationMode		1.3.6.1.4.1.710.3.2.1.2.5
When this attribute is set to ON, data frames are being translated for the Wireless LAN transmission. If it is set to OFF, tunneling of data frames apply. All devices within the same Wireless LAN network, must have the same Translation Mode assigned.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

brzWIXSupport		1.3.6.1.4.1.710.3.2.1.2.6
This attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resulting with balanced Basic Service Sets (cells). This option may be set only at some of the stations in the network.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

brzWlanNetID		1.3.6.1.4.1.710.3.2.1.2.7
This attribute identifies the Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allowed to associate to APs with different Net IDs.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(31)

brzAuthenticationType		1.3.6.1.4.1.710.3.2.1.2.8
This attribute indicates the authentication algorithm used during the authentication sequence. The value of this attribute is one of the following: 1 - Open System, 2 - Shared Key, 20 - Special Authentication Algorithm (#0), 21 - Special Authentication Algorithm (#1), 22 - Special Authentication Algorithm (#2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

brzWlanRTNetID		1.3.6.1.4.1.710.3.2.1.2.9
This attribute identifies the run-time Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allowed to associate to APs with different Net IDs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(31)

brzApRedundancySupport		1.3.6.1.4.1.710.3.2.1.2.10
Setting the value of this attribute to ON will cause the Access-Point to discontinue sending beacons to the Wireless LAN after no multicast or unicast frames for the cell arrive from the Ethernet during a period of 100 seconds. This option is available ONLY on AP (na value assigned in non-AP devices).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), na(255)

brzWlanRelayUnicast		1.3.6.1.4.1.710.3.2.1.2.11
This attribute enables the relaying of unicast frames on the WLAN within the BSS. Setting this attribute to OFF means that unicast frames received from the WLAN by the AP can only be passed to the Distribution System. Applicable only in AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), na(255)

brzWlanRelayBroadcast		1.3.6.1.4.1.710.3.2.1.2.12
This attribute enables the relaying of broadcast frames on the WLAN within the BSS. Setting this attribute to OFF means that broadcast frames received from the WLAN by the AP can only be passed to the Distribution System. Applicable only in AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), na(255)

brzApRedundancyLimit		1.3.6.1.4.1.710.3.2.1.2.13
This attribute sets the time until an Access-Point discontinues sending beacons to the Wireless LAN when no multicast or unicast frames for the cell arrive from the Ethernet. This option is available ONLY on AP (na value assigned in non-AP devices).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	na(255)

brzStaNumForLargeCW		1.3.6.1.4.1.710.3.2.1.2.14
This attribute sets the minimum number of stations in this cell that will cause this unit to use large CW, else this unit will use the default CW. (The value is in the range of 1-120)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzPowerMngMode		1.3.6.1.4.1.710.3.2.1.2.15
This attribute describes the current power management mode of the station. The allowed values are ACTIVE (for normal mode of operation), and POWER SAVE. An STA will always return an ACTIVE value.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

brzACKDelayed		1.3.6.1.4.1.710.3.2.1.2.16
This attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resulting with balanced Basic Service Sets (cells). This option may be set only at some of the stations in the network.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

brzDTIMPperiod		1.3.6.1.4.1.710.3.2.1.2.17
This attribute defines the rate of DTIM frames. The value is expressed in Beacon Intervals. This attribute is applicable only in AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzPowerMngBitTestMode		1.3.6.1.4.1.710.3.2.1.2.18
This attribute describes the current power management bit test mode of the AP. The allowed values are DISABLED (for normal mode of operation), and ENABLED.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

brzBeaconInterval		1.3.6.1.4.1.710.3.2.1.2.19
This attribute defines the rate of Beacon frames. The value is expressed in Dwells. This attribute is applicable only in AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzPowerSaveSupport		1.3.6.1.4.1.710.3.2.1.2.20
This attribute defines the power save support. 0 - Power Save support disabled 1 - Power Save support enabled 2 - Enable Power Save support with PM bit test This attribute is applicable only in AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1), enabled-with-pm-bit(2)

brzWlanAssocAge		1.3.6.1.4.1.710.3.2.1.2.21
This attribute defines the Association Aging Period.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzEnableVoice		1.3.6.1.4.1.710.3.2.1.2.22
This attribute Enables voice priority over other transmissions. This attribute is applicable only in AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

brzNonActiveCodeState		1.3.6.1.4.1.710.3.2.1.2.26
This attribute displays the current non active code state. WARNING: Activate this attribute will cause substantial degradation in station throughput, also answer is delayed!!!
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(25)

brzDisplayNonActiveCodeVersion		1.3.6.1.4.1.710.3.2.1.2.27
This attribute displays the active code version and the non active code version.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(80)

brzIntelligentBridgingPeriod		1.3.6.1.4.1.710.3.2.1.2.28
This attribute defines the Intelligent Bridging Period in seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

ipParams		1.3.6.1.4.1.710.3.2.2
OBJECT IDENTIFIER

trapHostsTable		1.3.6.1.4.1.710.3.2.2.1
A list of trap-hosts entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TrapHostsEntry

trapHostsEntry		1.3.6.1.4.1.710.3.2.2.1.1
A trap-receiving host entry, containing trap-host objects for a particular host.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TrapHostsEntry

trapHostsIndex		1.3.6.1.4.1.710.3.2.2.1.1.1
A unique value for each trap-host. Its value ranges between 1 and 3
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

trapIPaddress		1.3.6.1.4.1.710.3.2.2.1.1.2
The IP address of the host to be sent all traps
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

trapCommunity		1.3.6.1.4.1.710.3.2.2.1.1.3
The community of the host to be sent all traps
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

ipAddr		1.3.6.1.4.1.710.3.2.2.2
The IP address of this device, used to access the device through any of its LAN Ports (Ethernet or WLAN).
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

maskIP		1.3.6.1.4.1.710.3.2.2.3
The IP Network mask used by the IP entity when accessing devices through any of its LAN Ports (Ethernet or WLAN).
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

readCommunity		1.3.6.1.4.1.710.3.2.2.4
The device read community. If updated, it will be used after the next reset.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

writeCommunity		1.3.6.1.4.1.710.3.2.2.5
The device write community. If updated, it will be used after the next reset.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

gatewayIPaddr		1.3.6.1.4.1.710.3.2.2.6
Gateway default IP address.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

brzIPStack		1.3.6.1.4.1.710.3.2.2.7
This attribute defines whether to use IP stack or not.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(0)

brzWlan		1.3.6.1.4.1.710.3.2.3
OBJECT IDENTIFIER

brzWlanParams		1.3.6.1.4.1.710.3.2.3.1
OBJECT IDENTIFIER

brzMaxRate		1.3.6.1.4.1.710.3.2.3.1.1
This attribute indicates the rate (in Mbits per second) at which data will be transmitted across the medium. The default value of this attribute shall be 3.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..3

brzMobilLvl		1.3.6.1.4.1.710.3.2.3.1.2
This attribute indicates the expected mobility level of the system. The default value of this attribute is stationary.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	low(1), medium(2), high(3)

brzAvrgRssi		1.3.6.1.4.1.710.3.2.3.1.3
A value representing the average Signal Strength for packets received from the current AP. This attribute is applicable only for a station (An AP will always return a value of 255).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	na(255)

brzWlanProtocol		1.3.6.1.4.1.710.3.2.3.1.4
This attribute specifies the MAC/PHY protocol, utilized by this system. This attribute is not write accessible for regular users.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzWlanTrapThreashold		1.3.6.1.4.1.710.3.2.3.1.5
This attribute specifies a threshold value, for sending the WlanStatusTRAP. When the Wireless LAN quality drops below (or goes above) this value, a trap will be issued.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzWlanQuality		1.3.6.1.4.1.710.3.2.3.1.6
A measure for quality (and noise level) of the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	excellent(1), good(2), medium(3), bad(4), unknown(10)

knownAPsTable		1.3.6.1.4.1.710.3.2.3.1.7
A table of identities of the most recently known Access Points, and their signal quality.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		KnownAPsEntry

knownAPsEntry		1.3.6.1.4.1.710.3.2.3.1.7.1
An entry in the Known APs table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	KnownAPsEntry

knownAPsIndex		1.3.6.1.4.1.710.3.2.3.1.7.1.1
A unique value, representing the index of the AP in the Known APs table
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

knownAPsValue		1.3.6.1.4.1.710.3.2.3.1.7.1.2
This attributes specifies the address of a recently known AP. The default value of this attribute shall be null (an empty entry).
Status: mandatory	Access: read-write
OBJECT-TYPE
	MacAddress

knownAPsQuality		1.3.6.1.4.1.710.3.2.3.1.7.1.3
This attribute specifies the current reception quality of frames, transmitted by that AP. At a station, a GOOD value indicates that the station can join that AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	poor(1), good(2), unknown(10)

knownAPsAvrgRssi		1.3.6.1.4.1.710.3.2.3.1.7.1.4
A value representing the average Signal Strength for packets received from that AP in RSSI units.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

knownAPsStatus		1.3.6.1.4.1.710.3.2.3.1.7.1.5
The validity of the current entry, either invalid or valid.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	valid(1), invalid(2)

knownAPsLoadStations		1.3.6.1.4.1.710.3.2.3.1.7.1.6
A value representing the number of stations associated to that AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

knownAPsGoodBeacons		1.3.6.1.4.1.710.3.2.3.1.7.1.7
A value representing the number of beacons received with Strength more then join level from that AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

knownAPsTotalBeacons		1.3.6.1.4.1.710.3.2.3.1.7.1.8
A value representing the total number of beacons (good and bad) received from that AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

knownAPsAvrgDbm		1.3.6.1.4.1.710.3.2.3.1.7.1.9
A value representing the average Signal Strength for packets received from that AP in DBN units.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(10)

brzLastBeacon		1.3.6.1.4.1.710.3.2.3.1.8
A value representing last dwell to receive beacon from that AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

brzBadBeacons		1.3.6.1.4.1.710.3.2.3.1.9
A value representing the number of beacons received with Strength less then join level from that AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

brzLoadStations		1.3.6.1.4.1.710.3.2.3.1.10
A value representing the number of stations associated to that AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

brzAvrgDBm		1.3.6.1.4.1.710.3.2.3.1.11
A value representing the average Signal Strength for packets received from the current AP. This attribute is applicable only for a station (An AP will always return a value of -255).
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(10)

brzAP		1.3.6.1.4.1.710.3.2.3.2
OBJECT IDENTIFIER

bssInfo		1.3.6.1.4.1.710.3.2.3.2.1
OBJECT IDENTIFIER

bssNumOfStations		1.3.6.1.4.1.710.3.2.3.2.1.1
This attribute specifies the number of devices, that are currently associated with this AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bssNumOfStationsPeak		1.3.6.1.4.1.710.3.2.3.2.1.2
This attribute contains the maximum value that bssNumOfStations has reached.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bssCollectPerStationInfo		1.3.6.1.4.1.710.3.2.3.2.1.3
When this attribute is set to ON, the AP accumulates Wireless Link statistics per each station. This option is available only for the AP. At stations it is always assigned with na (Not Applicable) value. WARNING: Setting this attribute to ON can cause substantial degradation in cell throughput!!!
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2), na(255)

bssNumOfBeaconSent		1.3.6.1.4.1.710.3.2.3.2.1.4
This attribute contains the total beacons sent counter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bssNumOfBeaconLost		1.3.6.1.4.1.710.3.2.3.2.1.5
This attribute contains the total beacons lost counter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bssNumOfStationsAuthenticated		1.3.6.1.4.1.710.3.2.3.2.1.6
This attribute specifies the number of devices, that are currently Authenticated with this AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bssNumOfStationsAuthenticatedPeak		1.3.6.1.4.1.710.3.2.3.2.1.7
This attribute contains the maximum value that bssNumOfStationsAuthenticated has reached.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bssApAdb		1.3.6.1.4.1.710.3.2.3.2.2
OBJECT IDENTIFIER

adbTable		1.3.6.1.4.1.710.3.2.3.2.2.1
A table of the stations associated.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AdbEntry

adbEntry		1.3.6.1.4.1.710.3.2.3.2.2.1.1
An entry in ADB table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AdbEntry

stAddress		1.3.6.1.4.1.710.3.2.3.2.2.1.1.1
The MAC Address of the station represented by this entry in the Association Data Base
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

stCFMode		1.3.6.1.4.1.710.3.2.3.2.2.1.1.4
This attribute is set to ON if the station is in the Contention Free Polling list of the AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

stMaxRate		1.3.6.1.4.1.710.3.2.3.2.2.1.1.5
This attribute indicates the maximum rate (in Mbits per second) at which that station transmits data across the Wireless medium.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

stCurTxRate		1.3.6.1.4.1.710.3.2.3.2.2.1.1.6
The rate currently used by the AP to transmit packets to this station
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

stRssi		1.3.6.1.4.1.710.3.2.3.2.2.1.1.7
A value representing the average Signal Strength for packets received from that station in RSSI units. This attribute is being updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

stPMMode		1.3.6.1.4.1.710.3.2.3.2.2.1.1.8
The current Power Management mode of this station Power saving mode enables WLAN units (such as laptops or hand-held devices) to conserve battery power. To enable this feature, first enable power saving for the AP, and then enable power saving in the SA-PCR Card.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), power-saved(2)

stTxFragments		1.3.6.1.4.1.710.3.2.3.2.2.1.1.9
This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stTxFragments1M		1.3.6.1.4.1.710.3.2.3.2.2.1.1.10
This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 1Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stTxFragments2M		1.3.6.1.4.1.710.3.2.3.2.2.1.1.11
This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stTxFragments3M		1.3.6.1.4.1.710.3.2.3.2.2.1.1.12
This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 3Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stTxRetry		1.3.6.1.4.1.710.3.2.3.2.2.1.1.13
This attribute counts the total number of retransmissions to that station, over the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stTxDroppedPackets		1.3.6.1.4.1.710.3.2.3.2.2.1.1.14
This attribute counts the number of transmit frames (data or management) to this station, that were dropped because of too many retransmissions. It is updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stRxFragments		1.3.6.1.4.1.710.3.2.3.2.2.1.1.15
This attribute counts the total number of fragments (data and management) that have been received successfully from that station, through the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stWlanStatus		1.3.6.1.4.1.710.3.2.3.2.2.1.1.16
This attribute specifies the current reception quality of frames, transmitted by that station.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	poor(1), good(2), unknown(10)

stResetCounters		1.3.6.1.4.1.710.3.2.3.2.2.1.1.17
Setting the value of this attribute to ON, will clear the station counters at the AP (clear the counters in that adbEntry). Warning: Setting the value of this attribute to ON may cause momentary degradation in performance
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), off(2)

stType		1.3.6.1.4.1.710.3.2.3.2.2.1.1.18
This attribute identifies the device type of the station.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	sa-10(1), wb-10(2), sa-40(3), sa-pc(4), breeze-new(5), unknown(6)

stTxRetryPercent		1.3.6.1.4.1.710.3.2.3.2.2.1.1.19
This attribute calculate the retransmitted percentage, that was retransmitted to that station over the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stReTxFragments1M		1.3.6.1.4.1.710.3.2.3.2.2.1.1.20
This attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 1Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stReTxFragments2M		1.3.6.1.4.1.710.3.2.3.2.2.1.1.21
This attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stReTxFragments3M		1.3.6.1.4.1.710.3.2.3.2.2.1.1.22
This attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

stDbm		1.3.6.1.4.1.710.3.2.3.2.2.1.1.23
A value representing the average Signal Strength for packets received from that station in DBM units. This attribute is being updated only if sysCollectPerStationInfo is set to ON.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(10)

brzSTA		1.3.6.1.4.1.710.3.2.3.3
OBJECT IDENTIFIER

brzCurrentAPMacAddress		1.3.6.1.4.1.710.3.2.3.3.1
Hardware MAC address of the AP currently associated with. Available ONLY in station.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

brzLastAPMacAddress		1.3.6.1.4.1.710.3.2.3.3.2
The Hardware MAC address of the last AP that the station was associated with. Available ONLY in stations.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

brzPreferredAPMacAddress		1.3.6.1.4.1.710.3.2.3.3.3
The Hardware MAC address of the preferred AP, to which the station should associate when ever possible. Null value here indicates no preferences. Available ONLY in stations.
Status: mandatory	Access: read-write
OBJECT-TYPE
	MacAddress

brzRoamToAPMacAddress		1.3.6.1.4.1.710.3.2.3.3.4
Setting this attribute to a specific AP MAC address, will cause the station to roam immediately to that AP, if possible. Available ONLY for stations.
Status: mandatory	Access: read-write
OBJECT-TYPE
	MacAddress

brzCFMode		1.3.6.1.4.1.710.3.2.3.3.5
This attribute is set to ON if the station required Contention Free services from the AP (hence it is in the AP's Contention Free list). This option is available ONLY on stations. A Not Applicable value is returned for all APs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2), na(255)

brzTx1MBitRate		1.3.6.1.4.1.710.3.2.3.3.6
Total transmitted frames in 1 MBit rate.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTx2MBitRate		1.3.6.1.4.1.710.3.2.3.3.7
Total transmitted frames in 2 MBit rate.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTx3MBitRate		1.3.6.1.4.1.710.3.2.3.3.8
Total transmitted frames in 3 MBit rate.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTotalRetx		1.3.6.1.4.1.710.3.2.3.3.9
Total Retransmitted frames including all rates.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

brzRoamParams		1.3.6.1.4.1.710.3.2.3.4
OBJECT IDENTIFIER

brzRoamDecisionWin		1.3.6.1.4.1.710.3.2.3.4.1
This parameter defines a minimum number of RSSI samples which is required to make a decision about the current WLAN channel quality. A new RSSI sample arrives with each incoming frame. Available ONLY in stations.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzRoamDecisionNumerator		1.3.6.1.4.1.710.3.2.3.4.2
This parameter defines a maximum number of RSSI samples that is allowed to be below brzRoamDecisionRSSIThreshold, among a number equal to brzRoamDecisionWin of the last arrived samples. If a number of bad samples (i.e. below brzRoamDecisionRSSIThreshold) exceeds one, which is defined by this parameter, the channel is considered as bad. Available ONLY in stations.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzRoamDecisionRSSIThreshold		1.3.6.1.4.1.710.3.2.3.4.3
If an RSSI sample is bellow the value which is defined by this parameter the sample is considered as bad. Available ONLY in stations.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzJoinDecisionRSSIThreshold		1.3.6.1.4.1.710.3.2.3.4.4
A station will join a new AP only if the AP transmits with an RSSI quality above the value which is defined by this parameter. Available ONLY in stations. In AP's, this is the threshold for sending Bad WLAN Conditions traps. If a station associated with the AP is heard at an RSII level below this threshold, a Bad WLAN Conditions trap is sent by the AP.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzNeighboringBeacons		1.3.6.1.4.1.710.3.2.3.4.5
This parameters defines once in how many dwell times the AP will send a neighboring beacon. Available ONLY in AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzNumberOfProbeResponses		1.3.6.1.4.1.710.3.2.3.4.6
If a number of good RSSI samples coming from a neighbor is greater than or equal to this parameter the neighbor might be selected for joining.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzNumberOfBeaconsForDisconnect		1.3.6.1.4.1.710.3.2.3.4.7
This parameter defines a maximum number of consecutive not arrived Beacons that is allowed before a disconnect decision. Available ONLY in stations.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzMaxNumberOfScanning		1.3.6.1.4.1.710.3.2.3.4.8
This parameter defines a maximum number of scanning Attempts to perform before system reset. Zero is value for non reset. Available ONLY in stations.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzNeighboringBeaconRate		1.3.6.1.4.1.710.3.2.3.4.9
This parameter defines the Neighboring Beacon Rate in dwells. Zero is value for non Neighboring Beacons. Available ONLY in AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

brzCnt		1.3.6.1.4.1.710.3.2.4
OBJECT IDENTIFIER

brzDSCnt		1.3.6.1.4.1.710.3.2.4.1
OBJECT IDENTIFIER

brzRxFromDS		1.3.6.1.4.1.710.3.2.4.1.1
This attribute counts the total number of frames that have been received successfully from the Wired Distribution system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRxBadFromDS		1.3.6.1.4.1.710.3.2.4.1.2
This attribute counts the number errored frames, received from the Wired Distribution system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRxOctetsFromDS		1.3.6.1.4.1.710.3.2.4.1.3
This attribute counts the total number of octets that have been received successfully from the Wired Distribution system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTxToDS		1.3.6.1.4.1.710.3.2.4.1.4
This attribute counts the total number of frames that have been transmitted to the Wired Distribution system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzMissedFrames		1.3.6.1.4.1.710.3.2.4.1.5
This attribute counts the total number of missed frames that have missed the transmission to the Ethernet LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTxOctetsToDS		1.3.6.1.4.1.710.3.2.4.1.6
This attribute counts the total number of octets that have been transmitted successfully to the Wired Distribution system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRxOctetsForwardToWlan		1.3.6.1.4.1.710.3.2.4.1.7
This attribute counts the total number of octets that have been transmitted successfully to the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRxForwardToWlan		1.3.6.1.4.1.710.3.2.4.1.8
This attribute counts the total number of packets that have been transmitted successfully to the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzWlanCnt		1.3.6.1.4.1.710.3.2.4.2
OBJECT IDENTIFIER

brzTxWlanCnt		1.3.6.1.4.1.710.3.2.4.2.1
OBJECT IDENTIFIER

brzTxPacketsToWlan		1.3.6.1.4.1.710.3.2.4.2.1.1
This attribute counts the total number of frames (data and management) that have been transmitted to the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTxMSDUToWlan		1.3.6.1.4.1.710.3.2.4.2.1.2
This attribute counts the total number of frames (data frames) that have been transmitted to the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzDiscarded		1.3.6.1.4.1.710.3.2.4.2.1.3
This attribute counts the number of data frames, that were internally discarded in the system, instead of being transmitted over the Wireless LAN. High values of this counter indicate either very high traffic volume, or a noisy environment that prevents Wireless transmissions.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTxFragToWlan		1.3.6.1.4.1.710.3.2.4.2.1.4
This attribute counts the total number of fragments (data and management) that have been transmitted to the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRetryOnWlan		1.3.6.1.4.1.710.3.2.4.2.1.5
This attribute counts the total number of retransmitted fragments, on the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzFailedCountOnWlan		1.3.6.1.4.1.710.3.2.4.2.1.6
This attribute counts the number of frames that were dropped (not transmitted), due to the number of retransmits attempts exceeding the RetryMax value.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRetryOnWlanPercent		1.3.6.1.4.1.710.3.2.4.2.1.7
This attribute calculates the percentage of number frames (to the data and management) that have been transmitted successfully Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRetryTxDataToWlan		1.3.6.1.4.1.710.3.2.4.2.1.8
This attribute counts the total number of data frames that have been retransmitted to the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRetryTxDataToWlanPercent		1.3.6.1.4.1.710.3.2.4.2.1.9
This attribute calculates the percentage of data frames that have been transmitted successfully to the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTotalTxPacketsToWlan		1.3.6.1.4.1.710.3.2.4.2.1.10
This attribute counts the total number frames (data and management) that have been transmitted to the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTxErrTransmitions		1.3.6.1.4.1.710.3.2.4.2.1.15
OBJECT IDENTIFIER

brzTxErrorAckTimeOut		1.3.6.1.4.1.710.3.2.4.2.1.15.1
This attribute counts the total number of acknowledge timeouts on the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTxErrorAckCRC		1.3.6.1.4.1.710.3.2.4.2.1.15.2
This attribute counts the total number of acknowledge CRC Errors on the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTxErrorNoTimeUntilHop		1.3.6.1.4.1.710.3.2.4.2.1.15.3
This attribute counts the total number of timeouts caused of on time until end of hop on the Wireless Cell.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTxErrorUnderRunAndCTS		1.3.6.1.4.1.710.3.2.4.2.1.15.4
This attribute counts the total number of errors caused by HW problems (Under Run).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTxErrorAbort		1.3.6.1.4.1.710.3.2.4.2.1.15.5
This attribute counts the total number of errors caused by frame abortion from Boori.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzTxErrorFrameReceived		1.3.6.1.4.1.710.3.2.4.2.1.15.6
This attribute counts the total number of errors caused by frame failure on the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRxWlanCnt		1.3.6.1.4.1.710.3.2.4.2.2
OBJECT IDENTIFIER

brzRxPacketsFromWlan		1.3.6.1.4.1.710.3.2.4.2.2.1
This attribute counts the total number of frames (data and management) that have been received successfully from the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRxMSDUFromWlan		1.3.6.1.4.1.710.3.2.4.2.2.2
This attribute counts the total number of MSDUs (data frames) that have been received successfully from the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRxFragFromWlan		1.3.6.1.4.1.710.3.2.4.2.2.3
This attribute counts the number of fragments (data and management), that have been received successfully from the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRxBadFragFromWlan		1.3.6.1.4.1.710.3.2.4.2.2.4
This counter is incremented when an error is detected in a fragment, received from the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRxDuplicateFragFromWlan		1.3.6.1.4.1.710.3.2.4.2.2.5
This counter is incremented when a duplicated fragment is received from the Wireless LAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

freqStatisticsTable		1.3.6.1.4.1.710.3.2.4.2.2.6
A table for the traffic statistics of each frequency.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FreqStatisticsEntry

freqStatisticsEntry		1.3.6.1.4.1.710.3.2.4.2.2.6.1
An entry in the Frequencies Statistics table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	FreqStatisticsEntry

freqStatisticsIndex		1.3.6.1.4.1.710.3.2.4.2.2.6.1.1
A unique value, representing the index of the frequency in the hopping sequence table
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

freqNo		1.3.6.1.4.1.710.3.2.4.2.2.6.1.2
This attributes specifies the channel number of the frequency, for which this entry accumulates the statistics.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

freqTotalReceived		1.3.6.1.4.1.710.3.2.4.2.2.6.1.3
This attribute counts the total number of frames (data and management) that have been received successfully from the Wireless LAN, in that specific frequency.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzRoamCnt		1.3.6.1.4.1.710.3.2.4.3
OBJECT IDENTIFIER

brzNumOfReassocRequests		1.3.6.1.4.1.710.3.2.4.3.1
For an AP: The number of Associations and ReAssociations requests, received since the last reset of the AP. This counter is useful for getting information about mobility activity on the BSS. For a Station: The number of Associations and ReAssociation requests issued by the station since the last reset.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzMngCnt		1.3.6.1.4.1.710.3.2.4.4
OBJECT IDENTIFIER

brzMngAP		1.3.6.1.4.1.710.3.2.4.4.1
OBJECT IDENTIFIER

probeResponseSent		1.3.6.1.4.1.710.3.2.4.4.1.1
For an AP: Number of Probe response that sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

probeResponseLost		1.3.6.1.4.1.710.3.2.4.4.1.2
For an AP: Number of Probe response that got lost.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

probeResponseSentRetx		1.3.6.1.4.1.710.3.2.4.4.1.3
For an AP: Number of retransmitted Probe response frames that sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

probeRequestRecive		1.3.6.1.4.1.710.3.2.4.4.1.4
For an AP: Number of Probe request frames that has received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

assocResponseSent		1.3.6.1.4.1.710.3.2.4.4.1.5
For an AP: Number of Association response frames that sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

assocResponseLost		1.3.6.1.4.1.710.3.2.4.4.1.6
For an AP: Number of Association response frames that got lost.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

assocResponseSentRetx		1.3.6.1.4.1.710.3.2.4.4.1.7
For an AP: Number of retransmitted Association response frames that sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

assocRequestRecive		1.3.6.1.4.1.710.3.2.4.4.1.8
For an AP: Number of Association request frames that has received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

reAssocRequestRecive		1.3.6.1.4.1.710.3.2.4.4.1.9
For an AP: Number of ReAssociation request frames that has received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzMngSAWB		1.3.6.1.4.1.710.3.2.4.4.2
OBJECT IDENTIFIER

probRequestSent		1.3.6.1.4.1.710.3.2.4.4.2.1
For WB or SA: Number of Probe request frames that sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

probResponceRecive		1.3.6.1.4.1.710.3.2.4.4.2.2
For WB or SA: Number of received Probe response frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

authRequestSent		1.3.6.1.4.1.710.3.2.4.4.2.3
For WB or SA: Number of Authentication request frames that sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

authRequestSentRetx		1.3.6.1.4.1.710.3.2.4.4.2.4
For WB or SA: Number of Retransmitted Authentication request frames that sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

authResponceRecive		1.3.6.1.4.1.710.3.2.4.4.2.5
For WB or SA: Number of received Authentication response frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

assocRequestSent		1.3.6.1.4.1.710.3.2.4.4.2.6
For WB or SA: Number of Association request frames that sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

assocRequestSentRetx		1.3.6.1.4.1.710.3.2.4.4.2.7
For WB or SA: Number of Retransmitted Association request frames that sent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

assocResponceRecive		1.3.6.1.4.1.710.3.2.4.4.2.8
For WB or SA: Number of received Association response frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

brzPSCnt		1.3.6.1.4.1.710.3.2.4.5
OBJECT IDENTIFIER

pSFreeEntries		1.3.6.1.4.1.710.3.2.4.5.1
For an AP: Number of station free entries.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

pSInternallydiscarded		1.3.6.1.4.1.710.3.2.4.5.2
For an AP: Number of Internally Discarded frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

pSstations		1.3.6.1.4.1.710.3.2.4.5.3
For an AP: Number of power saved station connected to this AP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

pSPowerSavingAged		1.3.6.1.4.1.710.3.2.4.5.4
For an AP: Number of frames that were not transmitted due to the end of aging time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

powreStationsTable		1.3.6.1.4.1.710.3.2.4.5.5
A list of trap-hosts entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PowreStationsEntry

powreStationsEntry		1.3.6.1.4.1.710.3.2.4.5.5.1
A trap-receiving host entry, containing trap-host objects for a particular host.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	PowreStationsEntry

powerSaveIndex		1.3.6.1.4.1.710.3.2.4.5.5.1.1
A unique value, representing the index of the frequency in the hopping sequence table
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

powerSaveStationID		1.3.6.1.4.1.710.3.2.4.5.5.1.2
The identifier numerator of the Station in the AP. Note : ID zero is Broadcast.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

powerSaveBuffered		1.3.6.1.4.1.710.3.2.4.5.5.1.3
This attributes specifies how many messages are waiting to that Station in the AP buffers
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

powerSaveAged		1.3.6.1.4.1.710.3.2.4.5.5.1.4
This attributes specifies how many Stations were deleted after long time of waiting
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

powerSaveSent		1.3.6.1.4.1.710.3.2.4.5.5.1.5
This attributes specifies how many messages were sent to that station
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

powerSaveQueueFull		1.3.6.1.4.1.710.3.2.4.5.5.1.6
This attributes specifies how many messages were discarded because the queue to that station was full
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

brzTraps		1.3.6.1.4.1.710.3.2.5
OBJECT IDENTIFIER

brzTrapAPMacAddr		1.3.6.1.4.1.710.3.2.5.1
The MAC address of an AP
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

brzTrapSTAMacAddr		1.3.6.1.4.1.710.3.2.5.2
The MAC address of a station device
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

brzTrapMacAddress		1.3.6.1.4.1.710.3.2.5.3
A STA or AP MAC address
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

brzTrapRssiQuality		1.3.6.1.4.1.710.3.2.5.4
The RSSI level of the signal received from the Access Point
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

brzTrapLastRssiQuality		1.3.6.1.4.1.710.3.2.5.5
The RSSI level of the signal received from the previous Access Point
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

brzTrapIndex		1.3.6.1.4.1.710.3.2.5.6
Index number for future trap implementation
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

brzTrapText		1.3.6.1.4.1.710.3.2.5.7
Textual string for future trap implementation
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

brzTrapToggle		1.3.6.1.4.1.710.3.2.5.8
A general ON/OFF toggle value, for the traps.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

brzTrapSTAType		1.3.6.1.4.1.710.3.2.5.9
This attribute identifies the device type of the station.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	sa10(1), wb10(2), sa40(3), sa-pc(4), breeze-new(5), unknown(6)

brzAProamingIn		1
A trap indicating that a station has roamed into this AP. It contains the MAC address of the associated station and the device type of that station.
TRAP-TYPE

brzAPassociated		2
An AP trap indicating that a new station was associated with this AP. It contains the MAC address of the associated station.
TRAP-TYPE

brzAPdisassociated		3
An AP trap indicating that the station dis-associated itself from the AP. The trap contains the MAC address of the disassociated station.
TRAP-TYPE

brzAPaging		4
An AP trap indicating that the station association was aged out, and removed from that AP. The trap contains the MAC address of the aging station
TRAP-TYPE

brzAProamedOut		5
An AP trap indicating that a given station has roamed out from this AP. The trap contains the MAC address of the roamed out station
TRAP-TYPE

brzAPWlanStatusap		7
An AP trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent.
TRAP-TYPE

brzWlanStatusOfStation		8
An AP trap, indicating a change in the quality of the Wireless connection, with a specific (associated) station. An ON value indicates a specially bad connection, and an OFF value is sent if the quality improves, exceeding a predetermined threshold value. The brzTrapMacAddress contains the MAC address of the applicable station.
TRAP-TYPE

brzGeneralAP		9
An AP general purpose trap, for future trap implementation.
TRAP-TYPE

brzWBassociated		6
A WB trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros).
TRAP-TYPE

brzWBWlanStatus		7
A WB trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent.
TRAP-TYPE

brzGeneralWB		9
A WB general purpose trap, for future trap implementation.
TRAP-TYPE

brzSTAassociated		6
A station trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros).
TRAP-TYPE

brzSTAWlanStatus		7
A STA trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent.
TRAP-TYPE

brzGeneralSTA		9
A STA general purpose trap, for future trap implementation.
TRAP-TYPE

brzSA40associated		6
A SA-40 trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros).
TRAP-TYPE

brzSA40WlanStatus		7
SA-40 trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent.
TRAP-TYPE

brzGeneralSA40		9
SA-40 general purpose trap, for future trap implementation.
TRAP-TYPE

brzdot11		1.3.6.1.4.1.710.3.2.6
OBJECT IDENTIFIER

dot11smt		1.3.6.1.4.1.710.3.2.6.1
OBJECT IDENTIFIER

dot11DefaultWEPKeys		1.3.6.1.4.1.710.3.2.6.1.3
OBJECT IDENTIFIER

dot11DefaultWEPKey1		1.3.6.1.4.1.710.3.2.6.1.3.1
This attribute indicates the WEP secret key value corresponding to KeyID 1. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

dot11DefaultWEPKey2		1.3.6.1.4.1.710.3.2.6.1.3.2
This attribute indicates the WEP secret key value corresponding to KeyID 2. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

dot11DefaultWEPKey3		1.3.6.1.4.1.710.3.2.6.1.3.3
This attribute indicates the WEP secret key value corresponding to KeyID 3. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

dot11DefaultWEPKey4		1.3.6.1.4.1.710.3.2.6.1.3.4
This attribute indicates the WEP secret key value corresponding to KeyID 4. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

dot11PrivacyGrp		1.3.6.1.4.1.710.3.2.6.1.6
OBJECT IDENTIFIER

dot11Preauthentication		1.3.6.1.4.1.710.3.2.6.1.6.1
This attribute, when true, enables Preauthentication algorithm.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

dot11PrivacyOptionImplemented		1.3.6.1.4.1.710.3.2.6.1.6.2
This attribute, when true, shall indicate that the 802.11 WEP option is implemented.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	true(1), false(2)

dot11PrivacyInvoke		1.3.6.1.4.1.710.3.2.6.1.6.3
This attribute indicates if a special mechanism is invoked, to protect the Wireless LAN transmissions. The value is one of the following: 1 - Standard WEP, 2 - No Encryption, 20 - Special Encryption (#0), 21 - Special Encryption (#1), 22 - Special Encryption (#2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dot11WEPDefaultKeyID		1.3.6.1.4.1.710.3.2.6.1.6.4
This attribute shall indicate the use of the first, second, third or fourth DefaultWEPKey when set to values of one, two, three or four.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11mac		1.3.6.1.4.1.710.3.2.6.2
OBJECT IDENTIFIER

dot11OperationGrp		1.3.6.1.4.1.710.3.2.6.2.1
OBJECT IDENTIFIER

dot11MaxMulticastRate		1.3.6.1.4.1.710.3.2.6.2.1.1
This attribute indicates the basic rate for multicast frames.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11DwellTime		1.3.6.1.4.1.710.3.2.6.2.1.2
This attribute indicates the dwell time in Kilo-microsecond Allowed Values for version 5.x.x and higher are between 19..390. For older versions values are between 1 - 3. This attribute is available only in AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11RTSThreshold		1.3.6.1.4.1.710.3.2.6.2.1.3
This attribute indicates the number of bytes in an MPDU (frame), above which an RTS/CTS handshake will be performed. Setting this attribute to be larger than the maximum frame size, will prevent the RTS/CTS handshake for frames transmitted by this station.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11ShortRetryLimit		1.3.6.1.4.1.710.3.2.6.2.1.4
This attribute indicates the number of retransmission attempts made, before a failure condition is indicated. Values between 0..20 .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11DwellRetryLimit		1.3.6.1.4.1.710.3.2.6.2.1.5
This attribute indicates the number of retransmission attempts made in several Dwells, before a failure condition is indicated. Values between 0..9 .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11FragmentationThreshold		1.3.6.1.4.1.710.3.2.6.2.1.6
This attribute specifies the current maximum size, in octets, of the MPDU that will be delivered to the PHY. A frame will be broken into fragments if its size exceeds the value of this attribute, after adding MAC header and tailors. The value is one of the following: 1 - 560 octets, 2 - 800 octets, 3 - 1518 octets.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11ShortRetryLimitForVoice		1.3.6.1.4.1.710.3.2.6.2.1.7
This attribute indicates the number of retransmission for voice attempts made, before a failure condition is indicated. Values between 0..9 . This option is only for AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11DwellRetryLimitForVoice		1.3.6.1.4.1.710.3.2.6.2.1.8
This attribute indicates the number of retransmission for voice attempts made in several Dwells, before a failure condition is indicated. Values between 0..5 . This option is only for AP's.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11res		1.3.6.1.4.1.710.3.2.6.3
OBJECT IDENTIFIER

dot11resAttribute		1.3.6.1.4.1.710.3.2.6.3.8
OBJECT IDENTIFIER

dot11ResourceInfo		1.3.6.1.4.1.710.3.2.6.3.8.2
OBJECT IDENTIFIER

dot11CurrentStationStatus		1.3.6.1.4.1.710.3.2.6.3.8.2.1
This attribute identifies the current Station Wlan status. This attribute is not available in AP's.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(30)

dot11TotalNumberOfAssocSinceLastReset		1.3.6.1.4.1.710.3.2.6.3.8.2.2
This attribute identifies how many time the device Associated since startup.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

dot11manufacturerName		1.3.6.1.4.1.710.3.2.6.3.8.2.3
This attribute identifies the manufacturer of the resource.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(20)

dot11manufacturerProductName		1.3.6.1.4.1.710.3.2.6.3.8.2.4
This attribute identifies the manufacturer product name of the resource.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(30)

dot11manufacturerProductVersion		1.3.6.1.4.1.710.3.2.6.3.8.2.5
This attribute identifies the manufacturer's product version of the resource.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(20)

dot11phy		1.3.6.1.4.1.710.3.2.6.4
OBJECT IDENTIFIER

dot11PhyOperationGrp		1.3.6.1.4.1.710.3.2.6.4.1
OBJECT IDENTIFIER

dot11CurrentRegDomain		1.3.6.1.4.1.710.3.2.6.4.1.3
This attribute specifies the regularity domain, for the radio operation of this device. This integer contains an 8 bit value, as defined below: 00h - EthAirNet, 10h - USA, 20h - Canada, 30h - Europe, 31h - Spain, 32h - France, 37h - Europe Double Deviation, 38h - Netherlands, 40h - Japan, 41h - Korea, 48h - Israel, 49h - Australia, 60h - Proprietary.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ethairnet(0), usa(16), canada(32), europe(48), spain(49), france(50), europe-dd(55), netherlands(56), japan(64), korea(65), israel(72), australia(73), proprietary(96)

dot11PhyAntennaGrp		1.3.6.1.4.1.710.3.2.6.4.3
OBJECT IDENTIFIER

dot11CurrentTxAntenna		1.3.6.1.4.1.710.3.2.6.4.3.2
This attribute specifies the current antenna being used to transmit. The value is one of the following: 0 - Intelligent antennas selection, 1 - Transmitting only with antenna 1, 2 - Transmitting always with antenna 2.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11PhyTxPwrGrp		1.3.6.1.4.1.710.3.2.6.4.4
OBJECT IDENTIFIER

dot11CurrentTxPwrLvl		1.3.6.1.4.1.710.3.2.6.4.4.11
This attribute specifies the power level, currently being used to transmit data. The value is one of the following: 0 - Low, or 1 - High.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	low(0), high(1)

dot11PhyFHSSGrp		1.3.6.1.4.1.710.3.2.6.4.5
OBJECT IDENTIFIER

dot11CurrentDwellTime		1.3.6.1.4.1.710.3.2.6.4.5.5
This attribute specifies the current time, in Kilo-microseconds, that the radio operates on a single channel. The value is from 19 - 390. The same Dwell Time value should be assigned to all the devices within the same Wireless LAN network.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11CurrentSet		1.3.6.1.4.1.710.3.2.6.4.5.6
This attribute represents the current set of patterns that the device is using to determine the hop sequence. The range of values is 1 to 3, and the default is 1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11CurrentPattern		1.3.6.1.4.1.710.3.2.6.4.5.7
This attribute represents the current pattern that the device is using to determine the hop sequence.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11MultySupport		1.3.6.1.4.1.710.3.2.6.5
OBJECT IDENTIFIER

dot11MultyRateSupport		1.3.6.1.4.1.710.3.2.6.5.1
This attribute indicates the multi cast rate support.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

dot11MultyRateDecisionWindow		1.3.6.1.4.1.710.3.2.6.5.2
This attribute indicates the multi cast rate decision window size.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dot11Maintenance		1.3.6.1.4.1.710.3.2.6.6
OBJECT IDENTIFIER

dot11WaitforAssociationAddress		1.3.6.1.4.1.710.3.2.6.6.1
This attribute indicates the station mac-address. 0 - Use mine 1 - Wait for update via Ethernet Available only for Stations.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	use-mine(0), get-from-ethernet(1)

dot11JapanCallSign		1.3.6.1.4.1.710.3.2.6.6.2
This attribute indicates the Japan call sign string. Available only for Japan Standard.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(17)