CADANT-CMTS-LAYER2CMTS-MIB

File: CADANT-CMTS-LAYER2CMTS-MIB.mib (89810 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
BRIDGE-MIB CADANT-PRODUCTS-MIB CADANT-TC
DOCS-IF3-MIB INET-ADDRESS-MIB IF-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY Integer32
Counter32 Unsigned32 DisplayString
TEXTUAL-CONVENTION RowStatus TimeInterval
TruthValue MacAddress OBJECT-GROUP
BridgeId Timeout cadLayer2
CardId PortId CerCardType
CerCardSubType CadBridgeGroupId CadBridgePortType
PrimaryState SecondaryState DuplexStatus
AdminState MacPortId MacPortIdWithInvalid
PortType AttributeMask IfDirection
InetVersion InterfaceIndex InterfaceIndexOrZero

Defined Types

CadTftpEnforceType  
Cable TFTP Enforce configuration option types. The value `disabled' implies cable TFTP Enforce is inhibited. Any value other than `disabled' indicates some form of TFTP Enforce is active. The value `enabled' implies that if the TFTP Enforce checks fail, the modem will be denied registration. `mark-only ' implies that if the TFTP Enforce checks fail, the modem will be marked as having failed but will be allowed to register. ` lock ' implies that if the TFTP Enforce checks fail, the modem will be marked as having failed and will be allowed to register, but will have its bandwidth limited. ` block ' implies that if the TFTP Enforce checks fail, the modem will be marked as having failed and will be allowed to register, but will have its bandwidth limited and will not be allowed to learn any CPEs.
TEXTUAL-CONVENTION    
  INTEGER disabled(0), enabled(1), mark-only(2), lock(3), block(4)  

CadDynamicSecretType  
Cable Dynamic Secret configuration option types. The value `disabled' implies cable Dynamic Secret is inhibited. Any value other than `disabled' indicates some form of Dynamic Secret is active. The value `enabled' implies that if the Dynamic Secret checks fail, the modem will be denied registration. `mark' implies that if the Dynamic Secret checks fail, the modem will be marked as having failed but will be allowed to register. ` lock ' implies that if the Dynamic Secret checks fail, the modem will be marked as having failed and will be allowed to register, but will have its bandwidth limited. ` block ' implies that if the Dynamic Secret checks fail, the modem will be marked as having failed and will be allowed to register, but will have its bandwidth limited and will not be allowed to learn any CPEs.
TEXTUAL-CONVENTION    
  INTEGER disabled(0), reject(1), mark(2), lock(3), block(4)  

CadBridgeGroupEntry  
SEQUENCE    
  cadBgIndex CadBridgeGroupId
  cadBgName DisplayString
  cadBgRowStatus RowStatus

CadBridgeGroupStatsEntry  
SEQUENCE    
  cadBgLeaderBgpId InterfaceIndexOrZero
  cadBgMacAddress MacAddress

CadBridgePortEntry  
SEQUENCE    
  cadBgpGroupId CadBridgeGroupId
  cadBgpId InterfaceIndex
  cadBgpCardId CardId
  cadBgpCardType CerCardType
  cadBgpPortId PortId
  cadBgpType CadBridgePortType
  cadBgpBundleGroupId InterfaceIndexOrZero
  cadBgpMacAddress MacAddress

CadBridgeGroupPortStatusEntry  
SEQUENCE    
  cadBgpStatGroupId CadBridgeGroupId
  cadBgpStatMacIfIndex InterfaceIndex
  cadBgpStatPhyIfIndex InterfaceIndex
  cadBgpStatPhyCardId CardId
  cadBgpStatPhyPortId PortId

CadDot3adAggEntry  
SEQUENCE    
  cadDot3adAggId INTEGER
  cadDot3adAggIndex InterfaceIndex
  cadDot3adAggMacAddress MacAddress
  cadDot3adAggLacpEnable TruthValue
  cadDot3adAggLacpMode INTEGER
  cadDot3adAggLacpRate INTEGER
  cadDot3adAggMinLinks INTEGER
  cadDot3adAggDescription DisplayString
  cadDot3adAggTrapInh BITS
  cadDot3adAggAdminState AdminState
  cadDot3adAggPrState PrimaryState
  cadDot3adAggSecState SecondaryState
  cadDot3adAggRowStatus RowStatus
  cadDot3adAggSystemID MacAddress

CadMacPortEntry  
SEQUENCE    
  cadMacPortId MacPortId
  cadMacPortAdminState AdminState
  cadMacPortPrState PrimaryState
  cadMacPortSecState SecondaryState
  cadMacPortDplxStatus DuplexStatus
  cadMacPortMacAddress MacAddress
  cadMacPortIfIndex InterfaceIndex
  cadMacPortDescription DisplayString
  cadMacPortTrapInh BITS
  cadMacPortRowStatus RowStatus
  cadMacPortOfdm TruthValue

CadIfMacDomainEntry  
SEQUENCE    
  cadIfMacDomainIfIndex InterfaceIndex
  cadIfMacDomainCapabilities BITS
  cadIfMacDomainSyncInterval Integer32
  cadIfMacDomainUcdInterval Integer32
  cadIfMacDomainMaxServiceIds Integer32
  cadIfMacDomainInvitedRangingAttempts Integer32
  cadIfMacDomainInsertInterval INTEGER
  cadIfMacDomainRangingInterval TimeInterval
  cadIfMacDomainTftpEnforce CadTftpEnforceType
  cadIfMacDomainRangeOpportunityCycle TimeInterval
  cadIfMacDomainDynamicSecret CadDynamicSecretType
  cadIfMacDomainAnnex INTEGER
  cadIfMacDomainMddInterval Unsigned32
  cadIfMacDomainIpProvMode INTEGER
  cadIfMacDomainCmStatusEvCtlEnabled TruthValue
  cadIfMacDomainUsFreqRange INTEGER
  cadIfMacDomainMcastDsidFwdEnabled TruthValue
  cadIfMacDomainDsBondingEnabled TruthValue
  cadIfMacDomainMultTxChModeEnabled TruthValue
  cadIfMacDomainEarlyAuthEncrCtrl INTEGER
  cadIfMacDomainTftpProxyEnabled TruthValue
  cadIfMacDomainSrcAddrVerifEnabled TruthValue
  cadIfMacDomainMulticastEncryption TruthValue
  cadIfMacDomainRcpReportMode INTEGER
  cadIfMacDomainRegRspToOverride Unsigned32
  cadIfMacDomainMultRxChModeEnabled TruthValue
  cadIfMacDomainCmUdcEnabled TruthValue
  cadIfMacDomainSendUdcRulesEnabled TruthValue
  cadIfMacDomainRccDynEnable TruthValue
  cadIfMacDomainDsbgDynEnable TruthValue
  cadIfMacDomainDsbgReseqWaitTime Unsigned32
  cadIfMacDomainDsbgReseqWarnThrshld Unsigned32
  cadIfMacDomainDpId Integer32
  cadIfMacDomainUsbgDynEnable TruthValue
  cadIfMacDomainDownChannelMaxFrequency INTEGER
  cadIfMacDomainDownChannelMinFrequency INTEGER
  cadIfMacDomainUpChannelMaxFrequency INTEGER
  cadIfMacDomainBpi2Mandatory INTEGER
  cadIfMacDomainDSG30Enabled TruthValue
  cadIfMacDomainEnforceRulesEnabled TruthValue
  cadIfMacDomainCmTxPwrExtentionPreRegistrationEnabled TruthValue
  cadIfMacDomainCmTxPwrExtentionPostRegistrationEnabled TruthValue
  cadIfMacDomainT4TimeoutMultiplierEnabled TruthValue
  cadIfMacDomainDynamicRccMultiTunerEnabled TruthValue
  cadIfMacDomainTcsSizeLimit Integer32
  cadIfMacDomainDocsis31Enabled TruthValue
  cadIfMacDomainEnergyMgt1x1Enabled TruthValue
  cadIfMacDomainDsOfdmProfileRecoveryGuardTime Integer32
  cadIfMacDomainGracefulTcsReductionEnabled TruthValue

CadMacChlEntry  
SEQUENCE    
  cadMacChlMacDomainIfIndex InterfaceIndex
  cadMacChlChannelIfIndex InterfaceIndex
  cadMacChlCardNumber CardId
  cadMacChlPortId PortId
  cadMacChlPortType PortType
  cadMacChlCardSubType CerCardSubType
  cadMacChlChannelId Integer32
  cadMacChlRowStatus RowStatus
  cadMacChlIsPriCapableDs TruthValue
  cadMacChlSfProvAttrMask AttributeMask
  cadMacChlDirection IfDirection

CadUpSupervisionCfgEntry  
SEQUENCE    
  cadUpSupervisionCfgUpChannelIfIndex InterfaceIndex
  cadUpSupervisionCfgDownChannelIfIndex InterfaceIndex
  cadUpSupervisionCfgAssign TruthValue
  cadUpSupervisionCfgRowStatus RowStatus

CadUpSupervisionStatusEntry  
SEQUENCE    
  cadUpSupervisionStatusUpChannelIfIndex InterfaceIndex
  cadUpSupervisionStatusDownChannelIfIndex InterfaceIndex
  cadUpSupervisionStatusAssignmentMethod INTEGER

Defined Values

cadLayer2Mib 1.3.6.1.4.1.4998.1.1.20.1
This MIB module contains the following information: 1) The concept of bridge groups and bridge ports 2) The policy governed the assigment of Internet Service Provider's subnet addresses per bridge group 3) Support for per bridge group spanning tree
MODULE-IDENTITY    

cadBridgeGroup 1.3.6.1.4.1.4998.1.1.20.1.1
OBJECT IDENTIFIER    

cadBridgeGroupGeneral 1.3.6.1.4.1.4998.1.1.20.1.1.1
OBJECT IDENTIFIER    

cadBridgeGroupMaxNum 1.3.6.1.4.1.4998.1.1.20.1.1.1.1
The maximum number of bridge groups supported.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cadBridgeGroupTable 1.3.6.1.4.1.4998.1.1.20.1.1.2
A table (and along with other supported tables) contains bridge group information. A bridge group is actually a Port-Vlan concept which consists of one or more E-ports and one or more D-ports. Each D-port includes its associated U-ports and is further subdivided into 3 sub-ports associated with different types of traffic. The CM sub-port carries traffic for the cable-modem itself. The CPEAUTH sub-port carries traffic for an authorized CPE behind a cable-modem. The CPEUNAUTH sub-port carries traffic for an unauthorized CPE behind a cable-modem. Initially, all ports belong to the OAM&P bridge group when a card is first provisioned. Bridge ports can only exist in one bridge group at a time and can be moved between them. Generally, the CPEAUTH sub-port on the D card would be in a bridge group with an E port that had access to the internet and the DHCP servers for the ISP used by the subscriber. The CM sub-port would be in a bridge group with an E port that had access to the DHCP servers and administrative controls for the MSO. The CPEUNAUTH sub-port would be in a bridge group that included access to a sign-on server.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CadBridgeGroupEntry

cadBridgeGroupEntry 1.3.6.1.4.1.4998.1.1.20.1.1.2.1
A conceptual row containing information about different types of CMTS's broadcast domains and their configuration parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  CadBridgeGroupEntry  

cadBgIndex 1.3.6.1.4.1.4998.1.1.20.1.1.2.1.1
CMTS broadcast domain Id. Used as index. It has a value from 1 to the value of bridgeGroupMaxNum
Status: current Access: not-accessible
OBJECT-TYPE    
  CadBridgeGroupId  

cadBgName 1.3.6.1.4.1.4998.1.1.20.1.1.2.1.2
Symbolic Name of the domain.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

cadBgRowStatus 1.3.6.1.4.1.4998.1.1.20.1.1.2.1.11
Control Object for row creation and deletion.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

cadBridgeGroupStatsTable 1.3.6.1.4.1.4998.1.1.20.1.1.10
A table which contains read-only (status) information on bridge groups.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CadBridgeGroupStatsEntry

cadBridgeGroupStatsEntry 1.3.6.1.4.1.4998.1.1.20.1.1.10.1
A conceptual row containing read-only information on bridge groups.
Status: current Access: not-accessible
OBJECT-TYPE    
  CadBridgeGroupStatsEntry  

cadBgLeaderBgpId 1.3.6.1.4.1.4998.1.1.20.1.1.10.1.1
The bridge port that is the leader for this bridge group. If there are no bridge ports in this bridge group or there are multiple bridge ports in this bridge group but none of them make a clear leader, then cadBgLeaderBgpId is zero. Otherwise, it is the cadBgpId of the leader bridge port for this bridge group.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

cadBgMacAddress 1.3.6.1.4.1.4998.1.1.20.1.1.10.1.2
The mac address of the layer 2 entity associated with this bridge group. If there are no layer 2 entities associated with the bridge group, this value will be zero. In the case of a bundle, this will be the mac address of the bundle group leader.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cadBridgePortTable 1.3.6.1.4.1.4998.1.1.20.1.1.11
A table contain broadcast domain Ports Configuration (i.e. E ports, D-ports, M-Ports...etc)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CadBridgePortEntry

cadBridgePortEntry 1.3.6.1.4.1.4998.1.1.20.1.1.11.1
A conceptual row containing port configuration within a bridge group.
Status: current Access: not-accessible
OBJECT-TYPE    
  CadBridgePortEntry  

cadBgpGroupId 1.3.6.1.4.1.4998.1.1.20.1.1.11.1.1
Bridge group index. The same index used in bridgeGroupTable to identify a bridge group.
Status: current Access: read-write
OBJECT-TYPE    
  CadBridgeGroupId  

cadBgpId 1.3.6.1.4.1.4998.1.1.20.1.1.11.1.2
The secondary index of this table identifies a port in a given bridge group.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cadBgpCardId 1.3.6.1.4.1.4998.1.1.20.1.1.11.1.3
The slot number of the card containing this bridge port.
Status: current Access: read-only
OBJECT-TYPE    
  CardId  

cadBgpCardType 1.3.6.1.4.1.4998.1.1.20.1.1.11.1.4
The primary Card Type. Refer to Cadant's Equipment Mib for CerCardType definition.
Status: current Access: read-only
OBJECT-TYPE    
  CerCardType  

cadBgpPortId 1.3.6.1.4.1.4998.1.1.20.1.1.11.1.5
The port number of the physical port containing this bridge port.
Status: current Access: read-only
OBJECT-TYPE    
  PortId  

cadBgpType 1.3.6.1.4.1.4998.1.1.20.1.1.11.1.6
The type of this bridge port.
Status: current Access: not-accessible
OBJECT-TYPE    
  CadBridgePortType  

cadBgpBundleGroupId 1.3.6.1.4.1.4998.1.1.20.1.1.11.1.10
The bridge port which is the bundle leader. If this value is 0, then this port is not part of a bundle group. If this value is equal to its cadBgpId, then this port is the bundle leader for its group. Otherwise, this value must point to a valid bridge port.
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndexOrZero  

cadBgpMacAddress 1.3.6.1.4.1.4998.1.1.20.1.1.11.1.11
The current mac address associated with the bridge port. Initially, this is the address associated with the MAC or Ethernet port, but can change as a result of bundling or sparing operations.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cadBridgeGroupPortStatusTable 1.3.6.1.4.1.4998.1.1.20.1.1.12
A table which contains status information on bridge group members.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CadBridgeGroupPortStatusEntry

cadBridgeGroupPortStatusEntry 1.3.6.1.4.1.4998.1.1.20.1.1.12.1
A conceptual row containing status information on possible bridge group members.
Status: current Access: not-accessible
OBJECT-TYPE    
  CadBridgeGroupPortStatusEntry  

cadBgpStatGroupId 1.3.6.1.4.1.4998.1.1.20.1.1.12.1.1
The bridge group id to which this physical interface belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  CadBridgeGroupId  

cadBgpStatMacIfIndex 1.3.6.1.4.1.4998.1.1.20.1.1.12.1.2
The ifIndex of the layer 2 entity associated with the bridge group.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cadBgpStatPhyIfIndex 1.3.6.1.4.1.4998.1.1.20.1.1.12.1.3
The ifIndex of the physical entity associated with the bridge group. This ifIndex corresponds to an actual physical port on the C4. For NAM ports that are both a layer 2 and physical entity, this value may be the same as as the cadBgmemStatMacIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cadBgpStatPhyCardId 1.3.6.1.4.1.4998.1.1.20.1.1.12.1.4
The cardId of the slot associated with the physical ifindex.
Status: current Access: read-only
OBJECT-TYPE    
  CardId  

cadBgpStatPhyPortId 1.3.6.1.4.1.4998.1.1.20.1.1.12.1.5
The portId of the port associated with the physical ifindex.
Status: current Access: read-only
OBJECT-TYPE    
  PortId  

cadDot3adAggTable 1.3.6.1.4.1.4998.1.1.20.1.1.13
This table extends the dot3adAggTable to control LACP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CadDot3adAggEntry

cadDot3adAggEntry 1.3.6.1.4.1.4998.1.1.20.1.1.13.1
This is an extension of the dot3adAggEntry table that adds a LAG-level LACP enable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CadDot3adAggEntry  

cadDot3adAggId 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.1
The unique identifier allocated to this Aggregator by the CMTS system.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..8  

cadDot3adAggIndex 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.2
The unique ifInex to identify this Aggregator.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

cadDot3adAggMacAddress 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.3
The MAC address of this Aggregator.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cadDot3adAggLacpEnable 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.4
TRUE if LACP is enabled for this LAG, FALSE if it is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cadDot3adAggLacpMode 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.5
The default administrative status of the LACP protocol for ports In this LAG. Controls bit 0 of dot3adAggPortPartnerOperState to zero for passive and is set to one for active.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER active(1), passive(2)  

cadDot3adAggLacpRate 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.6
Specifies the default requested exchange rate of LACP packets for ports In this LAG. Controls bit 1 (LACP_Timeout) in dot3adAggPortActorOperState slow(1): The device requests its peers to send LACP packets at a slow rate to this interface. LACP_Timeout equals 0 (transmission interval of 30 seconds, long timeout of 90 seconds) fast(2) : The device requests its peers to send LACP packets at fast rate to this interface. LACP_Timeout equals 1 (transmission interval of 1 second, short timeout of 3 seconds).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER slow(1), fast(2)  


cadDot3adAggDescription 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.8
The description of the Link Aggregation Group.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

cadDot3adAggTrapInh 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.9
If a bit is set, the corresponding state change trap will not be sent. By default only linkUp and linkDown notifications are enabled.
Status: current Access: read-create
OBJECT-TYPE    
  BITS primary(0), secondary(1), duplex(2), linkUpLinkDown(3)  

cadDot3adAggAdminState 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.10
The administrative state of the Link Aggregation Group.
Status: current Access: read-create
OBJECT-TYPE    
  AdminState  

cadDot3adAggPrState 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.11
The primary state of the Link Aggregation Group.
Status: current Access: read-only
OBJECT-TYPE    
  PrimaryState  

cadDot3adAggSecState 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.12
The secondary state of the Link Aggregation Group.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cadDot3adAggRowStatus 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.13
Control Object for row creation and deletion.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cadDot3adAggSystemID 1.3.6.1.4.1.4998.1.1.20.1.1.13.1.14
Equivalent to the dot3adAggActorSystemID in the dot3adAggTable. A 6-octet read-write MAC address value used as a unique identifier for the System that contains this Aggregator.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cadDot3adParams 1.3.6.1.4.1.4998.1.1.20.1.1.14
OBJECT IDENTIFIER    

cadDot3adSystemPriority 1.3.6.1.4.1.4998.1.1.20.1.1.14.1
A 2-octet value that indicates the priority value associated with the Actor's System ID.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cadAging 1.3.6.1.4.1.4998.1.1.20.1.2
OBJECT IDENTIFIER    

cadAgingCPEAgingInterval 1.3.6.1.4.1.4998.1.1.20.1.2.1
MAC Aging counter granularity.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval 10..10  

cadAgingSFAgingInterval 1.3.6.1.4.1.4998.1.1.20.1.2.2
Service Flow Aging granularity.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval 1..1  

cadAgingStaleMACAgingInterval 1.3.6.1.4.1.4998.1.1.20.1.2.3
Stale MAC Flow Aging time in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..100000000  

cadAgingArpCacheAgingInterval 1.3.6.1.4.1.4998.1.1.20.1.2.4
Arp cache Aging time in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 600..360000  

cadAgingIdleMACAgingInterval 1.3.6.1.4.1.4998.1.1.20.1.2.5
The timeout period in seconds for aging out dynamically learned MAC information.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..1000000  

cadAgingArpCacheSearchingRateLimit 1.3.6.1.4.1.4998.1.1.20.1.2.6
The minimum amount of time between transmitting ARP requests while an ARP cache entry is in the searching state.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..86400000  

cadAgingArpCacheSearchingMaxNumber 1.3.6.1.4.1.4998.1.1.20.1.2.7
The maximum number of ARP requests transmitted while an ARP cache entry is in the searching state. When the number of ARPs indicated by this variable have been transmitted, the next packet that arrives for an ARP cache entry in the searching state will cause that entry to transition to the notPresent state.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cadAgingArpCacheNotPresentRateLimit 1.3.6.1.4.1.4998.1.1.20.1.2.8
The minimum amount of time between transmitting ICMP unreachables while an ARP cache entry is in the notPresent state.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..86400000  

cadAgingArpCacheNotPresentMaxNumber 1.3.6.1.4.1.4998.1.1.20.1.2.9
The maximum number of ICMP unreachables transmitted while an ARP cache entry is in the notPresent state. When the number of ICMPs indicated by this variable have been transmitted, the next packet that arrives for an ARP cache entry in the notPresent state will cause that entry to transition to the searching state, unless cadAgingArpCacheNotPresentMinTime has not been reached yet.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cadAgingArpCacheNotPresentMaxTime 1.3.6.1.4.1.4998.1.1.20.1.2.10
The maximum amount of time an ARP cache entry is in the notPresent state. When the amount of time indicated by this variable has elapsed, the next packet that arrives for an ARP cache entry in the notPresent state will cause that entry to transition to the searching state, unless cadAgingArpCacheNotPresentMinTime has not been reached yet.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..604800  

cadAgingArpCacheNotPresentMinTime 1.3.6.1.4.1.4998.1.1.20.1.2.11
The minimum amount of time an ARP cache entry is in the notPresent state. This variable takes precedence over cadAgingArpCacheNotPresentMaxNumber and cadAgingArpCacheNotPresentMaxTime. However, and ARP entry aged out due to inactivity will be removed regardless of whether the amount of time indicated by cadAgingArpCacheNotPresentMinTime has elapsed or not.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..604800  

cadAgingArpCacheSearchingGlobalMaxRate 1.3.6.1.4.1.4998.1.1.20.1.2.12
The maximum global ARP request transmit rate for all IP's with an ARP cache entry in the searching state. Units are in packets sent per second.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cadAgingArpCacheNotPresentGlobalMaxRate 1.3.6.1.4.1.4998.1.1.20.1.2.13
The maximum global ICMP unreachable transmit rate for all IP's with an ARP cache entry in the notPresent state. Units are in packets sent per second.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cadAgingNDCacheAgingInterval 1.3.6.1.4.1.4998.1.1.20.1.2.14
ND cache Aging time in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 180..360000  

cadAgingNDCacheSearchingRateLimit 1.3.6.1.4.1.4998.1.1.20.1.2.15
The minimum amount of time between transmitting ND requests while an ND cache entry is in the searching state.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..86400000  

cadAgingNDCacheSearchingMaxNumber 1.3.6.1.4.1.4998.1.1.20.1.2.16
The maximum number of ND requests transmitted while an ND cache entry is in the searching state. When the number of NDs indicated by this variable have been transmitted, the next packet that arrives for an ND cache entry in the searching state will cause that entry to transition to the notPresent state.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cadAgingNDCacheNotPresentRateLimit 1.3.6.1.4.1.4998.1.1.20.1.2.17
The minimum amount of time between transmitting ICMP unreachables while an ND cache entry is in the notPresent state.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..86400000  

cadAgingNDCacheNotPresentMaxNumber 1.3.6.1.4.1.4998.1.1.20.1.2.18
The maximum number of ICMP unreachables transmitted while an ND cache entry is in the notPresent state. When the number of ICMPs indicated by this variable have been transmitted, the next packet that arrives for an ND cache entry in the notPresent state will cause that entry to transition to the searching state, unless cadAgingNDCacheNotPresentMinTime has not been reached yet.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cadAgingNDCacheNotPresentMaxTime 1.3.6.1.4.1.4998.1.1.20.1.2.19
The maximum amount of time an ND cache entry is in the notPresent state. When the amount of time indicated by this variable has elapsed, the next packet that arrives for an ND cache entry in the notPresent state will cause that entry to transition to the searching state, unless cadAgingNDCacheNotPresentMinTime has not been reached yet.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..604800  

cadAgingNDCacheNotPresentMinTime 1.3.6.1.4.1.4998.1.1.20.1.2.20
The minimum amount of time an ARP cache entry is in the notPresent state. This variable takes precedence over cadAgingArpCacheNotPresentMaxNumber and cadAgingArpCacheNotPresentMaxTime. However, and ARP entry aged out due to inactivity will be removed regardless of whether the amount of time indicated by cadAgingArpCacheNotPresentMinTime has elapsed or not.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..604800  

cadAgingNDCacheSearchingGlobalMaxRate 1.3.6.1.4.1.4998.1.1.20.1.2.21
The maximum global ND request transmit rate for all IP's with an ND cache entry in the searching state. Units are in packets sent per second.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cadAgingNDCacheNotPresentGlobalMaxRate 1.3.6.1.4.1.4998.1.1.20.1.2.22
The maximum global ICMP unreachable transmit rate for all IP's with an ND cache entry in the notPresent state. Units are in packets sent per second.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cadAgingArpCacheSearchingCableUnicast 1.3.6.1.4.1.4998.1.1.20.1.2.23
The maximum number of unicast ARP requests transmitted while an ARP cache entry is in the searching state where the MAC/IP binding is previously known. After the number of unicast ARPs indicated by this variable have been transmitted, additional ARP requests will be sent as broadcast until the cadAgingArpCacheSearchingMaxNumber limit is reached, at which point the next packet that arrives for an ARP cache entry in the searching state will cause that entry to transition to the notPresent state.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cadAgingArpCacheSearchingCableBroadcast 1.3.6.1.4.1.4998.1.1.20.1.2.24
This variable controls whether broadcast ARP packets can be sent for an IPv4 address where there is no stored previous knowledge about a MAC/IP binding. The total number of broadcast ARPs to send before switching to the not-present state is limited by the cadAgingArpCacheSearchingMaxNumber variable. If cadAgingArpCacheSearchingCableBroadcast is false and there is no stored previous knowledge about a MAC/IP binding, the ARP cache entry will transition immediately to the not-present state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadAgingNDCacheSearchingCableUnicast 1.3.6.1.4.1.4998.1.1.20.1.2.25
The maximum number of unicast NS requests transmitted while an ND cache entry is in the searching state where the MAC/IP binding is previously known. After the number of unicast NSs indicated by this variable have been transmitted, additional NS requests will be sent as multicast until the cadAgingNDCacheSearchingMaxNumber limit is reached, at which point the next packet that arrives for an ND cache entry in the searching state will cause that entry to transition to the notPresent state.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cadAgingNDCacheSearchingCableMulticast 1.3.6.1.4.1.4998.1.1.20.1.2.26
This variable controls whether multicast NS packets can be sent for an IPv6 address where there is no stored previous knowledge about a MAC/IP binding. The total number of multicast NSs to send before switching to the not-present state is limited by the cadAgingNDCacheSearchingMaxNumber variable. If cadAgingNDCacheSearchingCableMulticast is false and there is no stored previous knowledge about a MAC/IP binding, the ND cache entry will transition immediately to the not-present state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

arrisCerIpGroup 1.3.6.1.4.1.4998.1.1.20.1.5
OBJECT IDENTIFIER    

cerIpGratuitousArpPeriod 1.3.6.1.4.1.4998.1.1.20.1.5.1
Configure the global time in seconds between gratuitous ARP transmission.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cadLayer2MibGroup 1.3.6.1.4.1.4998.1.1.20.1.3
OBJECT IDENTIFIER    

cadAgingGroup 1.3.6.1.4.1.4998.1.1.20.1.3.1
This group contains a collection of objects specific to MAC aging.
Status: current Access: read-write
OBJECT-GROUP    

cerIpGroup 1.3.6.1.4.1.4998.1.1.20.1.3.2
A collection of objects providing IP configuration for IEQ.
Status: current Access: read-write
OBJECT-GROUP    

cadMacPortMIBObjects 1.3.6.1.4.1.4998.1.1.20.1.4
OBJECT IDENTIFIER    

cadMacPortTable 1.3.6.1.4.1.4998.1.1.20.1.4.1
MAC port table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CadMacPortEntry

cadMacPortEntry 1.3.6.1.4.1.4998.1.1.20.1.4.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  CadMacPortEntry  

cadMacPortId 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.1
MAC port id which uniquely identifies a MAC port. Mac port Id range from 417 to 448 are reserved for 2D12U CAMs.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacPortId  

cadMacPortAdminState 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.4
The administrative state of the MAC port.
Status: current Access: read-create
OBJECT-TYPE    
  AdminState  

cadMacPortPrState 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.5
The primary state of the MAC port.
Status: current Access: read-only
OBJECT-TYPE    
  PrimaryState  

cadMacPortSecState 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.6
The secondary state of the MAC port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cadMacPortDplxStatus 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.7
The duplex status of the MAC port.
Status: current Access: read-only
OBJECT-TYPE    
  DuplexStatus  

cadMacPortMacAddress 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.8
The MAC address of the MAC port.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cadMacPortIfIndex 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.9
The ifIndex of the MAC port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

cadMacPortDescription 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.10
The description of the MAC port.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

cadMacPortTrapInh 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.11
If a bit is set, the corresponding state change trap will not be sent. By default only linkUp and linkDown notifications are enabled.
Status: current Access: read-create
OBJECT-TYPE    
  BITS primary(0), secondary(1), duplex(2), linkUpLinkDown(3)  

cadMacPortRowStatus 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.12
Control object for row creation and deletion.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cadMacPortOfdm 1.3.6.1.4.1.4998.1.1.20.1.4.1.1.13
If set to true, DOCSIS 3.1 is enabled for this MAC Port.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainTable 1.3.6.1.4.1.4998.1.1.20.1.4.2
The cadIfMacDomainTable maintains configuration information specific to each MAC domain. The table is indexed by the MAC domain ifIndex(from the ifTable or the cadMacPortTable).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CadIfMacDomainEntry

cadIfMacDomainEntry 1.3.6.1.4.1.4998.1.1.20.1.4.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  CadIfMacDomainEntry  

cadIfMacDomainIfIndex 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.1
MAC domain ifIndex
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cadIfMacDomainCapabilities 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.2
Identifies the capabilities of the CMTS MAC implementation at this interface.
Status: current Access: read-only
OBJECT-TYPE    
  BITS atmCells(0), concatentation(1)  

cadIfMacDomainSyncInterval 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.3
Interval between CMTS transmission of successive SYNC messages at this interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..200  

cadIfMacDomainUcdInterval 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.4
Interval between CMTS transmission of successive UCD messages for each upstream at this interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..2000  

cadIfMacDomainMaxServiceIds 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.5
Maximum number of service IDs that may be simultaneously active.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..16383  

cadIfMacDomainInvitedRangingAttempts 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.6
Maximum number of attempts to make on invitations for ranging requests. A value of 0 means the system should attempt to range forever.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1024  

cadIfMacDomainInsertInterval 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.7
Amount of time between each broadcast station maintenance grant.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..200  

cadIfMacDomainRangingInterval 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.8
Amount of time to elapse between each ranging message.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval 500..3500  

cadIfMacDomainRangeOpportunityCycle 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.9
Amount of time to elapse between each ranging cycle.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval 100..500  

cadIfMacDomainTftpEnforce 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.10
Current state of TFTP enforce for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  CadTftpEnforceType  

cadIfMacDomainDynamicSecret 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.11
Current state of Cable Dynamic Secret for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  CadDynamicSecretType  

cadIfMacDomainAnnex 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.13
The value of this object indicates the conformance of the implementation to important regional cable standards. annexA : Annex A from ITU-J83 is used. annexB : Annex B from ITU-J83 is used. annexC : Annex C from ITU-J83 is used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), other(2), annexA(3), annexB(4), annexC(5)  

cadIfMacDomainMddInterval 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.14
This attribute configures the interval for the insertion of MDD messages in each downstream channel of a MAC Domain.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..2000  

cadIfMacDomainIpProvMode 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.16
This attribute configures the CMTS IP provisioning mode for a MAC Domain. When this attribute is set to 'ipv4Only' the CM will acquire a single IPv4 address for the CM management stack. When this attribute is set to 'ipv6Only' the CM will acquire a single IPv6 address for the CM management stack. When this attribute is set to 'alternate' the CM will acquire a single IPv6 address for the CM management stack and, if failures occur, the CM will fall back to provisioning and operation with an IPv4 address. When this attribute is set to 'dualStack' the CM will acquire both an IPv6 and IPv4 address for provisioning and operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ipv4Only(0), ipv6Only(1), alternate(2), dualStack(3)  

cadIfMacDomainCmStatusEvCtlEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.18
If set to 'true', this attribute enables the signaling of the CM-Status Event reporting mechanism.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainUsFreqRange 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.19
This attribute indicates in MDD messages the upstream frequency upper band edge of an upstream Channel. A value 'standard' means Standard Frequency Range and a value 'extended' means Extended Frequency Range.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER standard(0), extended(1)  

cadIfMacDomainMcastDsidFwdEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.20
If set to 'true', this attribute enables the CMTS to use IP Multicast DSID Forwarding (MDF) for the MAC domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainDsBondingEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.21
If set to 'true', this attribute enables Downstream Channel Bonding for the MAC Domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainMultTxChModeEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.22
If set to 'true', this attribute enables Multiple Transmit Channel (MTC) Mode for the MAC Domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainEarlyAuthEncrCtrl 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.23
This attribute enables or disables early authentication and encryption (EAE) signaling for the MAC Domain. It also defines the type of EAE enforcement in the case that EAE is enabled. If set to 'disableEAE', EAE is disabled for the MAC Domain. If set to 'enableEaeRangingBasedEnforcement', 'enableEaeCapabilityBasedEnforcement' or 'enableEaeTotalEnforcement', EAE is enabled for the MAC Domain. The following EAE enforcement methods are defined in the case where EAE signaling is enabled: The option 'enableEaeRangingBasedEnforcement' indicates EAE is enforced on CMs that perform ranging with a B-INIT-RNG-REQ message. The option 'enableEaeCapabilityBasedEnforcement' indicates EAE is enforced on CMs that perform ranging with a B-INIT-RNG-REQ message in which the EAE capability flag is set. The option 'enableEaeTotalEnforcement' indicates EAE is enforced on all CMs regardless of their EAE capabilities.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disableEae(1), enableEaeRangingBasedEnforcement(2), enableEaeCapabilityBasedEnforcement(3), enableEaeTotalEnforcement(4)  

cadIfMacDomainTftpProxyEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.24
If set to 'true', this attribute enables TFTP Proxy functionality for the MAC Domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainSrcAddrVerifEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.25
If set to 'true', this attribute enables Source Address Verification (SAV) functionality for the MAC Domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainMulticastEncryption 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.26
If set to 'true', this attribute enables multicast encryption for all multicast flows on all downstream channels in the MAC domain using the des56 algorithm.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainRcpReportMode 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.27
This attribute controls the reporting of the CM receiver profiles in the registration messages. A value of 0 means that the CM MUST NOT provide verbose reporting of all its Receive Channel Profiles. A value of 1 means that the CM MUST provide verbose reporting of Receive Channel Profiles. both standard profiles and manufacturers profiles.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nonVerbose(0), verbose(1)  

cadIfMacDomainRegRspToOverride 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.28
This attribute provides an ability to override the default value of the T6 timer in the CM. When this attribute is not set to its default value, then the CMTS will place it into the MDD and the CM MUST use this value in place of the default value for the T6 timer.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

cadIfMacDomainMultRxChModeEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.29
If set to true, this attribute enables Downstream Channel Bonding for the MAC Domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainCmUdcEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.30
If set to true, this attribute instructs the CMTS MAC Domain to enable Upstream Drop Classifiers (UDC) for the CMs attempting registration in this MAC Domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainSendUdcRulesEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.31
If set to true and when the CM signals to the CMTS 'Upstream Drop Classifier Group ID encodings, this attribute instructs the CMTS MAC Domain to send the Subscriber Management Filters rules associated with the Upstream Drop Classifier Group ID encodings to the CM in the form of UDCs when the following conditions occurs: 1)The attribute CmUdcEnabled value for this MAC Domain is set to true, and 2)The CM has the UDC capability advertised as supported. If there is no a single Subscriber Management Filter configured in the CMTS for the CM signaled UDC Group ID, the CMTS does not send UDC encodings to the CM. It is vendor specific whether the CMTS maintains enforcement of the CM signaled or default Subscriber Management Filter groups in the upstream direction.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainRccDynEnable 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.32
This object allows user to enable or disable the autonomous creation of dynamic RCCs per mac domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainDsbgDynEnable 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.33
This object allows user to enable or disable the autonomous creation of dynamic bonding groups per mac domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainDsbgReseqWaitTime 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.34
Resequence wait time to se set for dynamic bonding groups per mac domain. If the value 255 indicates that requence wait time is determined by the CMTS.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..180 | 255  

cadIfMacDomainDsbgReseqWarnThrshld 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.35
Resequence warning threshold to se set for dynamic bonding groups per mac domain. If the value 255 indicates that requence warning threshold is determined by the CMTS.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..179 | 255  

cadIfMacDomainDpId 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.36
When a mac domain is created or system reset, DMM assigns a Downstream Pool ID (DPID) for each mac domain. If the value 255 indicates the DPID is invalid.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..15 | 255  

cadIfMacDomainUsbgDynEnable 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.37
This object allows user to enable or disable the autonomous creation of dynamic upstream bonding groups per mac domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainDownChannelMaxFrequency 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.38
This object is used to configure the C4 CMTS to accept maximum downstream frequency limit that conform with the EuroDOCSIS specifications (starndard range 112 MHz to 858 MHz), (extended 85 MHz to 999MHz) or to the DOCSIS specifications (standard 91 to 867 MHz), (extended range 57 MHz to 999 MHz). Changes to downstream frequency and width are verified against this object to ensure the C4 CMTS does not exceed the downstream spectrum limits imposed by this object. Attempting to decrease the downstream frequency spectrum implied by this object will fail if at least a single downstream is configured outside of the range for the new value. It is recommended this object be set during initial system setup.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 858000000 | 867000000 | 999000000  

cadIfMacDomainDownChannelMinFrequency 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.39
This object is used to configure the C4 CMTS to accept minimum downstream frequency limit that conform with the EuroDOCSIS specifications (starndard range 112 MHz to 858 MHz), (extended 85 MHz to 999MHz) or to the DOCSIS specifications (standard 91 to 867 MHz), (extended range 57 MHz to 999 MHz). Changes to downstream frequency and width are verified against this object to ensure the C4 CMTS does not exceed the downstream spectrum limits imposed by this object. Attempting to increase the minimum downstream frequency limit implied by this object will fail if at least a single downstream is configured outside of the range for the new value. It is recommended this object be set during initial system setup.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 57000000 | 85000000 | 91000000 | 112000000  

cadIfMacDomainUpChannelMaxFrequency 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.40
This object is used to configure the C4 CMTS to accept upstream frequency ranges that conform with the EuroDOCSIS specifications (5 MHz to 65 MHz), to the extended range used in Japan (5 MHz to 55 MHz), or to the DOCSIS specifications (5 MHz to 42 MHz), or to the extended upstream range (5 MHz to 85 MHz). Changes to upstream frequency and width are verified against this object to ensure the C4 CMTS does not exceed the upstream spectrum limits imposed by this object. Attempting to narrow the upstream frequency spectrum implied by this object will fail if at least a single upstream is configured outside of the range for the new value. Default value is taken from global setting when the cable-mac is created.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 42000000 | 55000000 | 65000000 | 85000000  

cadIfMacDomainBpi2Mandatory 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.41
This object determines the what minimum level of BPI operation is required in order to allow a cable modem to register.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), bpi(1), bpiPlus(2)  

cadIfMacDomainDSG30Enabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.43
If set to 'true', this attribute enables the CMTS to use DSG3.0 on the MAC domain. If false, then DSG reverts to the pre-DOCSIS3.0 version without DSIDs.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainEnforceRulesEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.44
If set to 'true', then QOS penalties as defined in the cadEnforceRuleTable will be enforced for SFs on CMs in this MAC Domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainCmTxPwrExtentionPreRegistrationEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.45
Indicate if the transmit power extension (before registration) feature is enabled or not onthe CMTS. If set to 'true', the CMTS will populate TLV16 in the MDD message with the value of 1. If set to 'false', the CMTS will populate TLV16 in the MDD message with the the value of 0. The value in this MIB object is ignored if MTCM is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainCmTxPwrExtentionPostRegistrationEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.46
Indicate if the transmit power extension (after registration) feature is enabled or not on the CMTS. If set to 'true', the CMTS will populate TLV5.40 in the REG-RSP-MP message with the same value received in the REG-REQ-MP message (advertised CM capability). If set to 'false', the CMTS will respond with 0 in TLV5.40 of the REG-RSP-MP message. The value in this MIB object is ignored if MTCM is disabled
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainT4TimeoutMultiplierEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.47
If set to true, this attribute instructs the CMTS MAC Domain to enable the T4 Timeout Multiplier for the CMs operating in MTCM in this MAC Domain. The multiplier will be set equal to the number of upstream assigned to the modem at registration time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainDynamicRccMultiTunerEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.48
If set to true, this attribute instructs the CMTS MAC Domain to enable dynamic RCC support for CM RCP's with multiple tuners.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainTcsSizeLimit 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.49
This object is used to potentially limit the number of channels within a CM's TCS. A value of 0 indicates the limit is determined by the CM's capabilities, configuration and operational status. When a non-zero value is specified and is smaller than the number of channels that are capable of residing within the CM's TCS, the number of channels within the CM's TCS will be restricted to the specified value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..8  

cadIfMacDomainDocsis31Enabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.50
If set to true, DOCSIS 3.1 is enabled for this MAC Domain.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainEnergyMgt1x1Enabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.51
This attribute indicates whether the CMTS is configured for 1x1 Energy Management Mode of operation on a per MAC Domain basis. If this attribute is set to 'true', the CMTS is configured for 1x1 Energy Management Mode of operation on this MAC Domain. If this attribute is set to 'false', the Energy Management 1x1 Mode of operation is disabled in the CMTS on this MAC Domain
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadIfMacDomainDsOfdmProfileRecoveryGuardTime 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.52
The amount of time that an impaired OFDM profile will remain impaired before transitioning to good upon being notified that the CM can decode the profile. This provides some hysteresis for a profile to become stable before using the newly decodable profile. If set to a value of 0, then there is no hysteresis (no timer is started) and all profiles may transition to good immediately upon being notified that the CM can decode the profile.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..3600  

cadIfMacDomainGracefulTcsReductionEnabled 1.3.6.1.4.1.4998.1.1.20.1.4.2.1.53
If set to true, the CMTS will instruct the modem to try incrementally lower numbers of bonded channels instead of reverting immediately to single US bonded channel while registering a modem and a power shortfall or DRW violation is encountered. If set to false, the CMTS will instruct the modem to immediately revert to a single US bonded channel while registering a modem and a power shortfall or DRW violation is encountered.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cadMacChlTable 1.3.6.1.4.1.4998.1.1.20.1.4.3
MAC channel table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CadMacChlEntry

cadMacChlEntry 1.3.6.1.4.1.4998.1.1.20.1.4.3.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  CadMacChlEntry  

cadMacChlMacDomainIfIndex 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.1
ifIndex of the MAC domain
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cadMacChlChannelIfIndex 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.2
ifIndex of the upstream or downstream channel
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cadMacChlCardNumber 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.3
card number of downstream or upstream channel
Status: current Access: read-only
OBJECT-TYPE    
  CardId  

cadMacChlPortId 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.4
port Id of downstream or upstream channel
Status: current Access: read-only
OBJECT-TYPE    
  PortId  

cadMacChlPortType 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.5
port type of downstream or upstream channel
Status: current Access: read-only
OBJECT-TYPE    
  PortType  

cadMacChlCardSubType 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.6
card subtype type of downstream or upstream channel
Status: current Access: read-only
OBJECT-TYPE    
  CerCardSubType  

cadMacChlChannelId 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.7
downstream or upstream channel ID. 0 is an invalid channel Id.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

cadMacChlRowStatus 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.8
Control object for row creation and deletion
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cadMacChlIsPriCapableDs 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.9
True if this is downstream channel and it is intended to be used as a primary channel by one or more cable modems. False otherwise. When a row's cadMacChlIsPrimaryCapableDs column is set to true(1) then DOCSIS SYNC message generation is enabled on the downstream channel. The default value of this field is true(1) for all downstream channels and false(2) for all upstream channels.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cadMacChlSfProvAttrMask 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.10
Provisioned attributes of this channel for purposes of channel assignment.
Status: current Access: read-create
OBJECT-TYPE    
  AttributeMask  

cadMacChlDirection 1.3.6.1.4.1.4998.1.1.20.1.4.3.1.11
DOCSIS downstream or upstream direction.
Status: current Access: read-only
OBJECT-TYPE    
  IfDirection  

cadUpSupervisionCfgTable 1.3.6.1.4.1.4998.1.1.20.1.4.4
Upstream supervison configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CadUpSupervisionCfgEntry

cadUpSupervisionCfgEntry 1.3.6.1.4.1.4998.1.1.20.1.4.4.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  CadUpSupervisionCfgEntry  

cadUpSupervisionCfgUpChannelIfIndex 1.3.6.1.4.1.4998.1.1.20.1.4.4.1.1
ifIndex of the upstream logical channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cadUpSupervisionCfgDownChannelIfIndex 1.3.6.1.4.1.4998.1.1.20.1.4.4.1.2
ifIndex of the downstream channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cadUpSupervisionCfgAssign 1.3.6.1.4.1.4998.1.1.20.1.4.4.1.3
Indicates whether supervisory information for the upstream channel with cadIfUpChannelIfIndex is to be carried on the downstream channel with cadIfDownChannelIfIndex.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cadUpSupervisionCfgRowStatus 1.3.6.1.4.1.4998.1.1.20.1.4.4.1.4
Control object for row creation and deletion.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cadUpSupervisionStatusTable 1.3.6.1.4.1.4998.1.1.20.1.4.5
Upstream supervision stataus table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CadUpSupervisionStatusEntry

cadUpSupervisionStatusEntry 1.3.6.1.4.1.4998.1.1.20.1.4.5.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  CadUpSupervisionStatusEntry  

cadUpSupervisionStatusUpChannelIfIndex 1.3.6.1.4.1.4998.1.1.20.1.4.5.1.1
ifIndex of the upstream logical channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cadUpSupervisionStatusDownChannelIfIndex 1.3.6.1.4.1.4998.1.1.20.1.4.5.1.2
ifIndex of the downstream channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

cadUpSupervisionStatusAssignmentMethod 1.3.6.1.4.1.4998.1.1.20.1.4.5.1.3
Origin of the supervisory relationship.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER automatic(1), provisioned(2)