CALIX-E7-SELT-LINE-MIB

File: CALIX-E7-SELT-LINE-MIB.mib (11303 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
SNMP-FRAMEWORK-MIB IF-MIB CALIX-PRODUCT-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Gauge32 Integer32 NOTIFICATION-TYPE
transmission Unsigned32 TruthValue
VariablePointer MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP SnmpAdminString ifIndex
e7 e7Modules

Defined Types

E7XdslSeltLineEntry  
SEQUENCE    
  e7XdslUsMargin INTEGER
  e7XdslDsMargin INTEGER
  e7XdslUsNumTones INTEGER
  e7XdslDsNumTones INTEGER
  e7XdslUsRate Unsigned32
  e7XdslDsRate Unsigned32
  e7XdslBestFitIdx INTEGER
  e7XdslLoopType INTEGER
  e7XdslLoopLength INTEGER
  e7XdslFitError INTEGER
  e7XdslSeltLineCmndConfLdsfFailReason INTEGER
  e7XdslSeltLineCmndConfLdsf INTEGER

E7SeltReportStatusEntry  
SEQUENCE    
  e7SeltBestFitIdx INTEGER
  e7SeltReportValid INTEGER
  e7SeltRoundTripDelay OCTET STRING
  e7SeltRoundTripError OCTET STRING
  e7SeltAttn300KHz OCTET STRING
  e7SeltAttn180KHz OCTET STRING
  e7SeltAttn1MHz OCTET STRING
  e7SeltAttnEndOfRange OCTET STRING
  e7SeltFitError OCTET STRING
  e7SeltTerminationPhase OCTET STRING
  e7SeltTransferFunction OCTET STRING
  e7SeltRangeStart INTEGER
  e7SeltRangeStop INTEGER

Defined Values

e7SeltTestDiags 1.3.6.1.4.1.6321.1.2.2.9
This MIB Module is for E7 xDSL SELT diagnostics.
MODULE-IDENTITY    

e7XdslSeltLineTable 1.3.6.1.4.1.6321.1.2.2.9.1
The table xdslSeltLineTable contains configuration, command and status parameters of the xDSL line. Several objects in this table MUST be maintained in a persistent manner.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    E7XdslSeltLineEntry

e7XdslSeltLineEntry 1.3.6.1.4.1.6321.1.2.2.9.1.1
The index of this table is an interface index where the interface has an ifType of xdslSelt(9).
Status: current Access: not-accessible
OBJECT-TYPE    
  E7XdslSeltLineEntry  

e7XdslUsMargin 1.3.6.1.4.1.6321.1.2.2.9.1.1.1
Selt US Margin.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7XdslDsMargin 1.3.6.1.4.1.6321.1.2.2.9.1.1.2
Selt DS Margin.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7XdslUsNumTones 1.3.6.1.4.1.6321.1.2.2.9.1.1.3
Selt US Number of Tones.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7XdslDsNumTones 1.3.6.1.4.1.6321.1.2.2.9.1.1.4
Selt DS Number of Tones.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7XdslUsRate 1.3.6.1.4.1.6321.1.2.2.9.1.1.5
Selt US capacity estimate rate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7XdslDsRate 1.3.6.1.4.1.6321.1.2.2.9.1.1.6
Selt DS capacity estimate rate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7XdslBestFitIdx 1.3.6.1.4.1.6321.1.2.2.9.1.1.7
Best fit/match reflection report index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7XdslLoopType 1.3.6.1.4.1.6321.1.2.2.9.1.1.8
Loop Type 0 = Awg 24, 1 = Awg 26.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7XdslLoopLength 1.3.6.1.4.1.6321.1.2.2.9.1.1.9
Loop Length Estimate in meters.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7XdslFitError 1.3.6.1.4.1.6321.1.2.2.9.1.1.10
Best Fit Error
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7XdslSeltLineCmndConfLdsfFailReason 1.3.6.1.4.1.6321.1.2.2.9.1.1.11
The status of the recent occasion the Loop diagnostics mode forced (LDSF) was issued for the associated line. Possible values are: none(1) - The default value in case LDSF was never requested for the associated line. success(2) - The recent command completed successfully. inProgress(3) - The Loop Diagnostics process is in progress. cannotRun(4) - The NE cannot initiate the command, due to a non-specific reason. aborted(5) - The Loop Diagnostics process aborted. failed(6) - The Loop Diagnostics process failed. tableFull(7) - The NE cannot initiate the command, due to reaching the maximum number of rows in the results table. noResources(8) - The NE cannot initiate the command, due to lack of internal memory resources.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), success(2), inProgress(3), cannotRun(4), aborted(5), failed(6)  

e7XdslSeltLineCmndConfLdsf 1.3.6.1.4.1.6321.1.2.2.9.1.1.12
Loop diagnostics mode forced (LDSF) for Selt Test. Defines whether the line should be forced into the Selt loop diagnostics mode by the near-end ATU on this line.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inhibit(0), force(1)  

e7SeltReportStatusTable 1.3.6.1.4.1.6321.1.2.2.9.2
The table SeltReportStatusTable contains status parameters for SELT test reflection report. The parameters in this table MUST be updated after a loop diagnostic procedure completion
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    E7SeltReportStatusEntry

e7SeltReportStatusEntry 1.3.6.1.4.1.6321.1.2.2.9.2.1
The table SeltReportStatusEntry contains status parameters of the SELT test reflection report. The index of this table is an interface index.
Status: current Access: not-accessible
OBJECT-TYPE    
  E7SeltReportStatusEntry  

e7SeltBestFitIdx 1.3.6.1.4.1.6321.1.2.2.9.2.1.1
SELT test best fit index. The valid values are 0, 1, 2.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2  

e7SeltReportValid 1.3.6.1.4.1.6321.1.2.2.9.2.1.2
SELT test report valid state values. 1 = valid and 0 = not-valid
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7SeltRoundTripDelay 1.3.6.1.4.1.6321.1.2.2.9.2.1.3
SELT test round trip delay.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

e7SeltRoundTripError 1.3.6.1.4.1.6321.1.2.2.9.2.1.4
SELT test round trip error.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

e7SeltAttn300KHz 1.3.6.1.4.1.6321.1.2.2.9.2.1.5
SELT test attenuation signal 300Khz.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

e7SeltAttn180KHz 1.3.6.1.4.1.6321.1.2.2.9.2.1.6
SELT test attenuation signal 180Khz.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

e7SeltAttn1MHz 1.3.6.1.4.1.6321.1.2.2.9.2.1.7
SELT test attenuation signal 1 MHz.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

e7SeltAttnEndOfRange 1.3.6.1.4.1.6321.1.2.2.9.2.1.8
SELT test attenuation end of range.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

e7SeltFitError 1.3.6.1.4.1.6321.1.2.2.9.2.1.9
SELT test fit error.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

e7SeltTerminationPhase 1.3.6.1.4.1.6321.1.2.2.9.2.1.10
SELT test termination phase.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

e7SeltTransferFunction 1.3.6.1.4.1.6321.1.2.2.9.2.1.11
SELT test transfer function.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

e7SeltRangeStart 1.3.6.1.4.1.6321.1.2.2.9.2.1.12
SELT test range start.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e7SeltRangeStop 1.3.6.1.4.1.6321.1.2.2.9.2.1.13
SELT test range stop.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER