CAMBIUM-PTP600-MIB

File: CAMBIUM-PTP600-MIB.mib (123716 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Integer32 IpAddress enterprises
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
DisplayString

Defined Types

DfsTableEntry  
SEQUENCE    
  dfsTableIndex INTEGER
  dfsMeans Integer32
  dfsNineNinePointNinePercentiles Integer32
  dfsPeaks Integer32

EthernetPriorityTableEntry  
SEQUENCE    
  ethernetPriorityTableIndex INTEGER
  ethernetPriorityQueueMapping INTEGER

L2CPPriorityTableEntry  
SEQUENCE    
  l2CPPriorityTableIndex INTEGER
  l2CPPriorityQueueMapping INTEGER

IPDSCPPriorityTableEntry  
SEQUENCE    
  iPDSCPPriorityTableIndex INTEGER
  iPDSCPPriorityQueueMapping INTEGER

MPLSTCPriorityTableEntry  
SEQUENCE    
  mPLSTCPriorityTableIndex INTEGER
  mPLSTCPriorityQueueMapping INTEGER

SNMPTrapTableEntry  
SEQUENCE    
  sNMPTrapTableIndex INTEGER
  sNMPTrapIPAddress IpAddress
  sNMPTrapPortNumber INTEGER

SNTPServerTableEntry  
SEQUENCE    
  sNTPServerTableIndex INTEGER
  sNTPServerIPAddress IpAddress
  sNTPServerPortNumber INTEGER
  sNTPServerStatus DisplayString

Defined Values

cambium 1.3.6.1.4.1.17713
MIB for 300Mbps non-line-of-sight (NLOS) wireless ethernet bridge.
MODULE-IDENTITY    

ptp 1.3.6.1.4.1.17713.1
OBJECT IDENTIFIER    

ptmp 1.3.6.1.4.1.17713.2
OBJECT IDENTIFIER    

ptp600 1.3.6.1.4.1.17713.6
OBJECT IDENTIFIER    

dfs 1.3.6.1.4.1.17713.6.3
OBJECT IDENTIFIER    

bridge 1.3.6.1.4.1.17713.6.4
OBJECT IDENTIFIER    

configuration 1.3.6.1.4.1.17713.6.5
OBJECT IDENTIFIER    

ethernet 1.3.6.1.4.1.17713.6.6
OBJECT IDENTIFIER    

telecom 1.3.6.1.4.1.17713.6.7
OBJECT IDENTIFIER    

licence 1.3.6.1.4.1.17713.6.8
OBJECT IDENTIFIER    

management 1.3.6.1.4.1.17713.6.9
OBJECT IDENTIFIER    

phyControl 1.3.6.1.4.1.17713.6.10
OBJECT IDENTIFIER    

phyStatus 1.3.6.1.4.1.17713.6.12
OBJECT IDENTIFIER    

alarms 1.3.6.1.4.1.17713.6.13
OBJECT IDENTIFIER    

smtp 1.3.6.1.4.1.17713.6.15
OBJECT IDENTIFIER    

snmpControl 1.3.6.1.4.1.17713.6.16
OBJECT IDENTIFIER    

sntp 1.3.6.1.4.1.17713.6.17
OBJECT IDENTIFIER    

reset 1.3.6.1.4.1.17713.6.18
OBJECT IDENTIFIER    

versions 1.3.6.1.4.1.17713.6.19
OBJECT IDENTIFIER    

pubStats 1.3.6.1.4.1.17713.6.20
OBJECT IDENTIFIER    

encryption 1.3.6.1.4.1.17713.6.22
OBJECT IDENTIFIER    

tDDControl 1.3.6.1.4.1.17713.6.23
OBJECT IDENTIFIER    

syslogControl 1.3.6.1.4.1.17713.6.24
OBJECT IDENTIFIER    

supplementary 1.3.6.1.4.1.17713.6.96
OBJECT IDENTIFIER    

ptpGroups 1.3.6.1.4.1.17713.6.98
OBJECT IDENTIFIER    

ptpTraps 1.3.6.1.4.1.17713.6.99
OBJECT IDENTIFIER    

ptpTrapPrefix 1.3.6.1.4.1.17713.6.99.0
OBJECT IDENTIFIER    

ptpCompliance 1.3.6.1.4.1.17713.6.97
The compliance statement for the Cambium PTP MIB
Status: current Access: read-write
MODULE-COMPLIANCE    

dfsGroup 1.3.6.1.4.1.17713.6.98.3
The dfs object group.
Status: current Access: read-write
OBJECT-GROUP    

bridgeGroup 1.3.6.1.4.1.17713.6.98.4
The bridge object group.
Status: current Access: read-write
OBJECT-GROUP    

configurationGroup 1.3.6.1.4.1.17713.6.98.5
The configuration object group.
Status: current Access: read-write
OBJECT-GROUP    

ethernetGroup 1.3.6.1.4.1.17713.6.98.6
The ethernet object group.
Status: current Access: read-write
OBJECT-GROUP    

telecomGroup 1.3.6.1.4.1.17713.6.98.7
The telecom object group.
Status: current Access: read-write
OBJECT-GROUP    

licenceGroup 1.3.6.1.4.1.17713.6.98.8
The licence object group.
Status: current Access: read-write
OBJECT-GROUP    

managementGroup 1.3.6.1.4.1.17713.6.98.9
The management object group.
Status: current Access: read-write
OBJECT-GROUP    

phyControlGroup 1.3.6.1.4.1.17713.6.98.10
The phyControl object group.
Status: current Access: read-write
OBJECT-GROUP    

phyStatusGroup 1.3.6.1.4.1.17713.6.98.12
The phyStatus object group.
Status: current Access: read-write
OBJECT-GROUP    

alarmsGroup 1.3.6.1.4.1.17713.6.98.13
The alarms object group.
Status: current Access: read-write
OBJECT-GROUP    

smtpGroup 1.3.6.1.4.1.17713.6.98.15
The smtp object group.
Status: current Access: read-write
OBJECT-GROUP    

snmpControlGroup 1.3.6.1.4.1.17713.6.98.16
The snmpControl object group.
Status: current Access: read-write
OBJECT-GROUP    

sntpGroup 1.3.6.1.4.1.17713.6.98.17
The sntp object group.
Status: current Access: read-write
OBJECT-GROUP    

resetGroup 1.3.6.1.4.1.17713.6.98.18
The reset object group.
Status: current Access: read-write
OBJECT-GROUP    

versionsGroup 1.3.6.1.4.1.17713.6.98.19
The versions object group.
Status: current Access: read-write
OBJECT-GROUP    

pubStatsGroup 1.3.6.1.4.1.17713.6.98.20
The pubStats object group.
Status: current Access: read-write
OBJECT-GROUP    

encryptionGroup 1.3.6.1.4.1.17713.6.98.22
The encryption object group.
Status: current Access: read-write
OBJECT-GROUP    

tDDControlGroup 1.3.6.1.4.1.17713.6.98.23
The tDDControl object group.
Status: current Access: read-write
OBJECT-GROUP    

syslogControlGroup 1.3.6.1.4.1.17713.6.98.24
The syslogControl object group.
Status: current Access: read-write
OBJECT-GROUP    

supplementaryGroup 1.3.6.1.4.1.17713.6.98.96
The supplementary object group.
Status: current Access: read-write
OBJECT-GROUP    

notificationsGroup 1.3.6.1.4.1.17713.6.98.99
The notifications group.
Status: current Access: read-write
NOTIFICATION-GROUP    

dfsTable 1.3.6.1.4.1.17713.6.3.2
A table storing a snapshot of various DFS measurements for each channel
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DfsTableEntry

dfsTableEntry 1.3.6.1.4.1.17713.6.3.2.1
Table DfsTable
Status: current Access: not-accessible
OBJECT-TYPE    
  DfsTableEntry  

ethernetPriorityTable 1.3.6.1.4.1.17713.6.6.15
A priority queue mapping table. This is a list of packet queues indexed by Ethernet priority.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EthernetPriorityTableEntry

ethernetPriorityTableEntry 1.3.6.1.4.1.17713.6.6.15.1
Table EthernetPriorityTable
Status: current Access: not-accessible
OBJECT-TYPE    
  EthernetPriorityTableEntry  

l2CPPriorityTable 1.3.6.1.4.1.17713.6.6.17
A priority queue mapping table. This is a list of packet queues indexed by L2CP priority.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    L2CPPriorityTableEntry

l2CPPriorityTableEntry 1.3.6.1.4.1.17713.6.6.17.1
Table L2CPPriorityTable
Status: current Access: not-accessible
OBJECT-TYPE    
  L2CPPriorityTableEntry  

iPDSCPPriorityTable 1.3.6.1.4.1.17713.6.6.19
A priority queue mapping table. This is a list of packet queues indexed by L3 IP DSCP priority.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IPDSCPPriorityTableEntry

iPDSCPPriorityTableEntry 1.3.6.1.4.1.17713.6.6.19.1
Table IPDSCPPriorityTable
Status: current Access: not-accessible
OBJECT-TYPE    
  IPDSCPPriorityTableEntry  

mPLSTCPriorityTable 1.3.6.1.4.1.17713.6.6.21
A priority queue mapping table. This is a list of priority queues indexed by MPLS TC priority.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MPLSTCPriorityTableEntry

mPLSTCPriorityTableEntry 1.3.6.1.4.1.17713.6.6.21.1
Table MPLSTCPriorityTable
Status: current Access: not-accessible
OBJECT-TYPE    
  MPLSTCPriorityTableEntry  

sNMPTrapTable 1.3.6.1.4.1.17713.6.16.4
SNMP trap configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SNMPTrapTableEntry

sNMPTrapTableEntry 1.3.6.1.4.1.17713.6.16.4.1
Table SNMPTrapTable
Status: current Access: not-accessible
OBJECT-TYPE    
  SNMPTrapTableEntry  

sNTPServerTable 1.3.6.1.4.1.17713.6.17.15
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SNTPServerTableEntry

sNTPServerTableEntry 1.3.6.1.4.1.17713.6.17.15.1
Table SNTPServerTable
Status: current Access: not-accessible
OBJECT-TYPE    
  SNTPServerTableEntry  

dfsTableNumber 1.3.6.1.4.1.17713.6.3.1
Number of entries in the dfsTable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..63  

dfsTableIndex 1.3.6.1.4.1.17713.6.3.2.1.1
used to index values in the dfsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..63  

dfsMeans 1.3.6.1.4.1.17713.6.3.2.1.2
Snapshot of DFS means
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dfsNineNinePointNinePercentiles 1.3.6.1.4.1.17713.6.3.2.1.3
Snapshot of DFS 99.9 percentiles
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dfsPeaks 1.3.6.1.4.1.17713.6.3.2.1.4
Snapshot of DFS peaks
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

localPacketFiltering 1.3.6.1.4.1.17713.6.4.1
When Local Packet Filtering is Enabled, the bridge learns the source MAC addresses of devices transmitting Ethernet packets on the local Ethernet network, and only bridges packets to the remote unit if the destination MAC address has not been learnt as a 'local' device. When Local Packet Filtering is Disabled then the bridge does not learn the source MAC addresses of devices transmitting Ethernet packets on the local Ethernet network, and bridges ALL Ethernet packets received to the remote unit. Local Packet Filtering should be enabled if no external routing hardware is present
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

iPAddress 1.3.6.1.4.1.17713.6.5.1
Internet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is required to activate changes to this attribute.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask 1.3.6.1.4.1.17713.6.5.2
A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance. NB: A system reboot is required to activate changes to this attribute
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

gatewayIPAddress 1.3.6.1.4.1.17713.6.5.3
The IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to other networks. NB: A system reboot is required to activate changes to this attribute
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

targetMACAddress 1.3.6.1.4.1.17713.6.5.4
MAC address of the PTP wireless unit forming the other end of the PTP link
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

masterSlaveMode 1.3.6.1.4.1.17713.6.5.5
The PTP wireless link operates using a master and slave relationship
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER master(0), slave(1)  

maximumTransmitPower 1.3.6.1.4.1.17713.6.5.6
Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -15..27  

antennaGain 1.3.6.1.4.1.17713.6.5.7
Antenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..610  

cableLoss 1.3.6.1.4.1.17713.6.5.8
Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

eIRP 1.3.6.1.4.1.17713.6.5.9
Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ethernetCappedMaxWirelessSpeed 1.3.6.1.4.1.17713.6.5.10
Ethernet frames will be discarded in the ODU if the data rate over the wireless link exceeds the Ethernet link speed at the local or remote Data port. The Ethernet Capped Max Wireless Speed control limits the wireless data rate based on the local and remote Ethernet link speed. Set this control to Enabled if either ODU is connected to an Ethernet link operating at less than 1000 Mbps. NB: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

channelBandwidth 1.3.6.1.4.1.17713.6.5.11
This control sets the bandwidth of the transmit and receive radio channels
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER bw30MHz(0), bw15MHz(1), bw10MHz(2), bw5MHz(3), bw20MHz(4)  

remoteIPAddress 1.3.6.1.4.1.17713.6.5.12
IP Address of the peer wireless unit
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

linkName 1.3.6.1.4.1.17713.6.5.14
Name of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

siteName 1.3.6.1.4.1.17713.6.5.15
This field contains a user-provided description of the site name together with any additional notes
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

accessMethod 1.3.6.1.4.1.17713.6.5.16
ODUs must be configured in pairs before a link can be established. The Access Method attribute determines how the paired ODUs will recognise each other. For the Link Access method, each ODU must be configured with Target MAC Address equal to the MAC Address of the other unit. For the Link Name Access method, both units must be configured with the same Link Name. For the Group Access method, both units must be configured with the same Group ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER linkAccess(0), linkNameAccess(1), groupAccess(2)  

groupID 1.3.6.1.4.1.17713.6.5.17
When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

dataPortAutoNegotiation 1.3.6.1.4.1.17713.6.6.1
This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dataPortAutoNegAdvertisement 1.3.6.1.4.1.17713.6.6.2
This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!
Status: current Access: read-write
OBJECT-TYPE    
  BITS negInvalid(2), neg10MbpsHalfDuplex(3), neg10MbpsFullDuplex(4), neg100MbpsHalfDuplex(5), neg100MbpsFullDuplex(6), neg1000MbpsFullDuplex(7)  

dataPortAutoMdix 1.3.6.1.4.1.17713.6.6.3
This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dataPortStatus 1.3.6.1.4.1.17713.6.6.4
Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(0), copperLinkUp(1), fiberLinkUp(2)  

dataPortSpeedAndDuplex 1.3.6.1.4.1.17713.6.6.5
The current speed and duplex of the Ethernet link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER speed1000MbpsFullDuplex(0), speed100MbpsFullDuplex(1), speed100MbpsHalfDuplex(2), speed10MbpsFullDuplex(3), speed10MbpsHalfDuplex(4), speedUnknown6(5)  

dataPortWirelessDownAlert 1.3.6.1.4.1.17713.6.6.6
When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

useVLANForManagementInterfaces 1.3.6.1.4.1.17713.6.6.7
This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noVLANTagging(0), iEEE8021QTaggedCTagType8100(1), iEEE8021adTaggedSTagorBTagType88a8(2)  

vLANManagementPriority 1.3.6.1.4.1.17713.6.6.8
This VLAN Priority (0-7) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER p0(0), p1(1), p2(2), p3(3), p4(4), p5(5), p6(6), p7(7)  

vLANManagementVID 1.3.6.1.4.1.17713.6.6.11
This VLAN VID (0-4094) will be included in packets generated by the management interfaces. Note the new setting will only take effect after a system reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4094  

managementPortStatus 1.3.6.1.4.1.17713.6.6.12
Current status of the out-of-band management link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(0), copperLinkUp(1)  

managementPortSpeedAndDuplex 1.3.6.1.4.1.17713.6.6.13
The current speed and duplex of the out-of-band management link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER speed100MbpsFullDuplex(1), speed100MbpsHalfDuplex(2), speed10MbpsFullDuplex(3), speed10MbpsHalfDuplex(4), speedUnknown6(5)  

ethernetPriorityTableNumber 1.3.6.1.4.1.17713.6.6.14
Number of entries in the vLANPriorityTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 9  

l2CPPriorityTableNumber 1.3.6.1.4.1.17713.6.6.16
Number of entries in the l2CPPriorityTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 5  

iPDSCPPriorityTableNumber 1.3.6.1.4.1.17713.6.6.18
Number of entries in the iPDSCPPriorityTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 64  

mPLSTCPriorityTableNumber 1.3.6.1.4.1.17713.6.6.20
Number of entries in the mPLSTCPriorityTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 8  

managementMode 1.3.6.1.4.1.17713.6.6.22
Out-of-Band Management (only available on certain hardware models): End-to-end out-of-band mode in which the management agent can be reached from the management port at the local ODU and (assuming that the wireless link is established) the management port at the remote ODU. Out-of-Band Local Management (only available on certain hardware models): Similar to the standard Out-of-Band mode, except that management frames are not forwarded over the wireless link. In-Band Management (default): The management agent can be reached from the data port at the local ODU and (assuming that the wireless link is established) the data port at the remote ODU. In this mode the management port is disabled. In-Band Local Management (only available when 'Use VLAN For Management Interfaces' configures a VLAN tag): Similar to the standard In-Band mode, except that management frames are not forwarded over the wireless link.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER outofBandLocal(0), outofBand(1), inBand(2), inBandLocal(3)  

managementPortWirelessDownAlert 1.3.6.1.4.1.17713.6.6.23
When enabled, this causes the management link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

qOSPriorityScheme 1.3.6.1.4.1.17713.6.6.24
Selects classification based on fields in the Ethernet header (Layer 2) or in the Network header (Layer 3). The unit recognises two network layer protocols: IP and MPLS
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ethernet(0), iPMPLS(1)  

unknownNetworkPriorityQueueMapping 1.3.6.1.4.1.17713.6.6.25
Configures the classification of unknown network protocols to an egress queue at the wireless port. Unknown means something other than IP and MPLS
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)  

dSCPManagementPriority 1.3.6.1.4.1.17713.6.6.26
This Differentiated Services Code Point value will be inserted in the IP Header of all IP Datagrams transmitted by the management interfaces
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..63  

ethernetBridgingStatus 1.3.6.1.4.1.17713.6.6.27
Current status of Ethernet packet bridging over the wireless link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

ethernetPriorityTableIndex 1.3.6.1.4.1.17713.6.6.15.1.1
Ethernet priority flag, used to index values in the ethernetPriorityTable
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER p0(1), p1(2), p2(3), p3(4), p4(5), p5(6), p6(7), p7(8), untagged(9)  

ethernetPriorityQueueMapping 1.3.6.1.4.1.17713.6.6.15.1.2
Configures the classification of this Ethernet priority (also known as IEEE 802.1p value) to an egress queue at the wireless port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)  

l2CPPriorityTableIndex 1.3.6.1.4.1.17713.6.6.17.1.1
L2CP priority flag, used to index values in the l2CPPriorityTable
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER bridge(1), mRP(2), cFM(3), rAPS(4), eAPS(5)  

l2CPPriorityQueueMapping 1.3.6.1.4.1.17713.6.6.17.1.2
Configures the classification of this layer two control protocol (L2CP) to an egress queue at the wireless port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)  

iPDSCPPriorityTableIndex 1.3.6.1.4.1.17713.6.6.19.1.1
IP DSCP priority flag, used to index values in the iPDSCPPriorityTable
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..64  

iPDSCPPriorityQueueMapping 1.3.6.1.4.1.17713.6.6.19.1.2
Configures the classification of this IP differentiated services code point (DSCP) value to an egress queue at the wireless port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)  

mPLSTCPriorityTableIndex 1.3.6.1.4.1.17713.6.6.21.1.1
MPLS TC priority flag, used to index values in the mPLSTCPriorityTable
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..8  

mPLSTCPriorityQueueMapping 1.3.6.1.4.1.17713.6.6.21.1.2
Configures the classification of this MPLS traffic class (the field formerly known as EXP) to an egress queue at the wireless port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)  

telecomsInterface 1.3.6.1.4.1.17713.6.7.1
The line interface type. If this is set to 'None' then the telecoms interfaces are disabled, and the telecom group attributes will be ignored.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), e1(1), t1(2)  

telecomsChannelAStatus 1.3.6.1.4.1.17713.6.7.2
Current status of telecoms channel A. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), noSignalLocal(1), noSignalRemote(2), noSignalLocalandRemote(3), up(4), remoteTiming(5), noSignalLocalandRemoteTiming(6)  

telecomsChannelBStatus 1.3.6.1.4.1.17713.6.7.3
Current status of telecoms channel B. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), noSignalLocal(1), noSignalRemote(2), noSignalLocalandRemote(3), up(4), remoteTiming(5), noSignalLocalandRemoteTiming(6)  

channelALineCode 1.3.6.1.4.1.17713.6.7.4
The line code setting of the telecoms interface. This must match the setting of the device connected to this interface
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER aMI(0), b8ZSHDB3(1)  

channelBLineCode 1.3.6.1.4.1.17713.6.7.5
The line code setting of the telecoms interface. This must match the setting of the device connected to this interface
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER aMI(0), b8ZSHDB3(1)  

channelACableLength 1.3.6.1.4.1.17713.6.7.6
The length of the cable connected to the telecoms interface, measured in feet
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER feet133(0), feet266(1), feet399(2), feet533(3), feet655(4)  

channelBCableLength 1.3.6.1.4.1.17713.6.7.7
The length of the cable connected to the telecoms interface, measured in feet
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER feet133(0), feet266(1), feet399(2), feet533(3), feet655(4)  

channelALoopback 1.3.6.1.4.1.17713.6.7.8
The loopback status of telecoms channel A. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), copper(1), wireless(2)  

channelBLoopback 1.3.6.1.4.1.17713.6.7.9
The loopback status of telecoms channel B. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), copper(1), wireless(2)  

telecomsChannelSelection 1.3.6.1.4.1.17713.6.7.10
Indicates which telecoms channels have been enabled. If only Channel A has been enabled, then the Channel B attributes will be ignored.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER channelAOnly(0), channelsAandB(1)  

regionCode 1.3.6.1.4.1.17713.6.8.1
The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted license key. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER regionCodeInvalid(0), regionCode1(1), regionCode2(2), regionCode3(3), regionCode4(4), regionCode5(5), regionCode6(6), regionCode7(7), regionCode8(8), regionCode9(9), regionCode10(10), regionCode11(11), regionCode12(12), regionCode13(13), regionCode14(14), regionCode15(15), regionCode16(16), regionCode17(17), regionCode18(18), regionCode19(19), regionCode20(20), regionCode21(21), regionCode22(22), regionCode23(23), regionCode24(24), regionCode25(25), regionCode26(26), regionCode27(27), regionCode28(28), regionCode29(29), regionCode30(30), regionCode31(31)  

productVariant 1.3.6.1.4.1.17713.6.8.2
The product variant
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER pTPxx400Full(0), pTPxx400Deprecated1(1), pTPxx400Deprecated2(2), pTPxx400Lite(3), spare1(4), pTPxx300(5), spare2(6), spare3(7), pTPxx500FullDeprecated(8), pTPxx500LiteDeprecated(9), pTPxx500(10), pTPxx600Lite(11), pTPxx600Full(12), spare5(13), spare6(14), pTP800(15)  

productName 1.3.6.1.4.1.17713.6.8.3
Name of the product variant
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

ethernetFiberSupport 1.3.6.1.4.1.17713.6.8.4
Ethernet fiber support availability on this wireless unit
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frequencyVariant 1.3.6.1.4.1.17713.6.8.5
Frequency variant of the wireless unit
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER freq5800MHz(0), freq5400MHz(1), freq4900MHz(2), freq2500MHz(3), freq5800MHz2(4), freq5400MHz2(5), freq4500MHz(6), freq5900MHz(7), freq5200MHz(8), freq5100MHz(9), freq4800MHz(10)  

bandwidthVariant 1.3.6.1.4.1.17713.6.8.6
Bandwidth variant of the wireless unit
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER bw30MHz(0), bw15MHz(1), bw10MHz(2), bw5MHz(3), bw20MHz(4)  

constantPowerSpectralDensity 1.3.6.1.4.1.17713.6.8.7
Constant power spectral density mode control
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER constant(0), fullPower(1)  

sNMPv3Enable 1.3.6.1.4.1.17713.6.8.9
SNMPv3 availability control
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

hAZLOCConfiguration 1.3.6.1.4.1.17713.6.8.10
The HAZLOC/ATEX Configuration of this unit. The Gas Group is configured by the license key.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonHAZLOCUnit(0), gasGroupA(1), gasGroupB(2), gasGroupC(3), gasGroupD(4)  

securityLevel 1.3.6.1.4.1.17713.6.8.11
The maximum configurable security level
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(0), fIPS(1), uCAPL(2)  

targetRange 1.3.6.1.4.1.17713.6.9.1
Initial target range used in installation +/-1, expressed in tenths of a kilometer. When Auto-Ranging this must be set to 0
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2000  

rangingMode 1.3.6.1.4.1.17713.6.9.2
Type of ranging to use during installation, either Auto-Ranging or use a selectable Target Range
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER auto0to40km(0), auto0to100km(1), auto0to200km(2), targetRange(3)  

installStatus 1.3.6.1.4.1.17713.6.9.3
A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), wrongPeer(1)  

installArmState 1.3.6.1.4.1.17713.6.9.4
Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disarmed(0), armed(1)  

tFTPServerIPAddress 1.3.6.1.4.1.17713.6.9.5
IP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

tFTPServerPortNumber 1.3.6.1.4.1.17713.6.9.6
The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

tFTPSoftwareUpgradeFileName 1.3.6.1.4.1.17713.6.9.7
Filename of the Software Upgrade to be loaded from the TFTP Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

tFTPStartSoftwareUpgrade 1.3.6.1.4.1.17713.6.9.8
Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished. Continuing with the software upgrade will cause spectrum management (iDFS) channel metrics collection to stop. The wireless unit will no longer search for the optimal operational radio channel. The performance of this wireless link may deterioate over time. If operating in a region where RADAR detection is mandatory you must complete the software upgrade and reboot the unit. Channel metrics collection will only be restarted after the wireless unit has been rebooted
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

tFTPSoftwareUpgradeStatus 1.3.6.1.4.1.17713.6.9.9
The current status of the TFTP Software upgrade process
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), uploadinprogress(1), uploadsuccessfulprogrammingFLASH(2), upgradesuccessfulreboottorunthenewsoftwareimage(3), upgradefailed(4)  

tFTPSoftwareUpgradeStatusText 1.3.6.1.4.1.17713.6.9.10
Descriptive text describing the status of the TFTP Software upgrade process, including any error details
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

tFTPSoftwareUpgradeStatusAdditionalText 1.3.6.1.4.1.17713.6.9.11
Any additional text describing the status of the TFTP Software upgrade process, including any error details
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

hTTPAccessEnabled 1.3.6.1.4.1.17713.6.9.12
This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

telnetAccessEnabled 1.3.6.1.4.1.17713.6.9.13
This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

hTTPPortNumber 1.3.6.1.4.1.17713.6.9.14
This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

hTTPSPortNumber 1.3.6.1.4.1.17713.6.9.15
This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the License Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

telnetPortNumber 1.3.6.1.4.1.17713.6.9.16
This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

hTTPSAccessEnabled 1.3.6.1.4.1.17713.6.9.17
This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

linkSymmetry 1.3.6.1.4.1.17713.6.10.1
Link Symmetry: in fixed symmetric mode the master spends an equal amount of time transmitting and receiving; in fixed asymmetric modes the master transmit and receive times have a fixed ratio; in adaptive mode the transmit and receive periods adjust with applied load.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER symmetryAdaptive(0), symmetry2to1(1), symmetry1to1(2), symmetry1to2(3)  

linkModeOptimisation 1.3.6.1.4.1.17713.6.10.2
Optimises the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimise transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimise transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER iPTraffic(0), tDMTraffic(1)  

userConfiguredMaxModulationMode 1.3.6.1.4.1.17713.6.10.3
The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER modBpsk63percent(0), modQpsk63percent(1), modQpsk87percent(2), mod16qam63percent(3), mod16qam87percent(4), mod64qam75percent(5), mod64qam92percent(6), mod256qam81percent(7)  

remoteMaximumTransmitPower 1.3.6.1.4.1.17713.6.10.4
Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -15..27  

txColorCode 1.3.6.1.4.1.17713.6.10.5
Transmit Color Code. This attribute need only be considered when the unit is installed in a network of PTP600 units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Rx Color Code parameter at the far end of the link.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER a(0), b(1), c(2), d(3), e(4)  

rxColorCode 1.3.6.1.4.1.17713.6.10.6
Receive Color Code. This attribute need only be considered when the unit is installed in a network of PTP600 units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Tx Color Code parameter at the far end of the link.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER a(0), b(1), c(2), d(3), e(4)  

automaticTxPowerControl 1.3.6.1.4.1.17713.6.10.8
When enabled, the transmit power of the local end is automatically adjusted to maintain a configurable target receive signal level at the remote end of the link. When set to Enable with initial estimate, the Slave estimates the optional transmit power before it responds to the Master.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), enabledwithinitialestimate(2)  

remoteRxTargetPower 1.3.6.1.4.1.17713.6.10.9
This is the target receive level for the end of the link which is remote from the end being configured. When Automatic Power Control is enabled, the transmit power of the local end is automatically adjusted in order to maintain the receive signal level at the remote end within a range centered on this value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -600..-400  

receivePower 1.3.6.1.4.1.17713.6.12.1
Receive power expressed in tenths of a dBm
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vectorError 1.3.6.1.4.1.17713.6.12.2
The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dB
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

transmitPower 1.3.6.1.4.1.17713.6.12.3
Transmit power expressed in tenths of a dBm
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

range 1.3.6.1.4.1.17713.6.12.4
Distance between the two peer wireless units expressed in tenths of a kilometer
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkLoss 1.3.6.1.4.1.17713.6.12.5
The wireless link loss expressed in tenths of a dB
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -500..500  

receiveChannel 1.3.6.1.4.1.17713.6.12.6
Current active receive channel
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..63  

transmitChannel 1.3.6.1.4.1.17713.6.12.7
Current active transmit channel
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..63  

receiveModulationMode 1.3.6.1.4.1.17713.6.12.8
Current active receive modulation mode
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER modAcquisition(0), modBpsk63percent(1), modQpsk63percentSingle(2), modTransient1(3), modQpsk87percentSingle(4), modTransient2(5), mod16qam63percentSingleA(6), modTransient3(7), mod16qam87percentSingle(8), modTransient4(9), mod64qam75percentSingle(10), modTransient5(11), mod64qam92percentSingle(12), modTransient6(13), mod256qam81percentSingle(14), mod16qam63percentSingleB(15), mod16qam63percentDual(16), modTransient7(17), mod16qam87percentDual(18), modTransient8(19), mod64qam75percentDual(20), modTransient9(21), mod64qam92percentDual(22), modTransient10(23), mod256qam81percentDual(24)  

transmitModulationMode 1.3.6.1.4.1.17713.6.12.9
Current active transmit modulation mode
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER modAcquisition(0), modBpsk63percent(1), modQpsk63percentSingle(2), modTransient1(3), modQpsk87percentSingle(4), modTransient2(5), mod16qam63percentSingleA(6), modTransient3(7), mod16qam87percentSingle(8), modTransient4(9), mod64qam75percentSingle(10), modTransient5(11), mod64qam92percentSingle(12), modTransient6(13), mod256qam81percentSingle(14), mod16qam63percentSingleB(15), mod16qam63percentDual(16), modTransient7(17), mod16qam87percentDual(18), modTransient8(19), mod64qam75percentDual(20), modTransient9(21), mod64qam92percentDual(22), modTransient10(23), mod256qam81percentDual(24)  

receiveFreqMHz 1.3.6.1.4.1.17713.6.12.11
Current receive frequency expressed in integer MHz
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..5925  

transmitFreqMHz 1.3.6.1.4.1.17713.6.12.12
Current transmit frequency expressed in integer MHz
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..5925  

signalStrengthRatio 1.3.6.1.4.1.17713.6.12.13
Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dB
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

receiveFreqKHz 1.3.6.1.4.1.17713.6.12.14
Current receive frequency expressed as KHz
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..5925000  

transmitFreqKHz 1.3.6.1.4.1.17713.6.12.15
Current transmit frequency expressed as KHz
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..5925000  

searchState 1.3.6.1.4.1.17713.6.12.16
Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER registering(0), searching(1), acquiring(2)  

rawReceivePower 1.3.6.1.4.1.17713.6.12.17
Raw receive power expressed in tenths of a dBm
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

unitOutOfCalibration 1.3.6.1.4.1.17713.6.13.1
The unit is out of calibration
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER calibrated(0), outOfCalibration(1), outOfCalibrationPAsShutdown(2)  

encryptionEnabledMismatch 1.3.6.1.4.1.17713.6.13.3
Encryption has been enabled on one end of the wireless link but not the other
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), encryptionEnabledMismatch(1)  

incompatibleRegionCodes 1.3.6.1.4.1.17713.6.13.4
The master and slave units have incompatible region codes. NB: Both units must have compatible license keys
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), incompatibleLicenceKeys(1)  

noWirelessChannelAvailable 1.3.6.1.4.1.17713.6.13.5
Spectrum Management was unable to locate a suitable wireless channel to operate on
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), noWirelessChannelAvailable(1)  

wirelessLinkDisabledWarning 1.3.6.1.4.1.17713.6.13.6
The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), disabledBySNMPifAdminStatus(1)  

dataPortDisabledWarning 1.3.6.1.4.1.17713.6.13.7
The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), disabledBySNMPifAdminStatus(1)  

dataPortFiberStatus 1.3.6.1.4.1.17713.6.13.8
If the fiber link is not OK, there are three possible causes: Either the fiber link has been installed but disabled (because the license key does not include fiber support), the link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), or the link could not be established and LOS is detected (i.e. no optical carrier is detected). NB: a change of status may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), installedFiberNotLicensed(1), fiberLinkNotEstablishedButLOSNotDetected(2), fiberLinkNotEstablishedAndLOSDetected(3)  

dataPortConfigurationMismatch 1.3.6.1.4.1.17713.6.13.9
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(0), mismatchDetected(1)  

incompatibleMasterAndSlave 1.3.6.1.4.1.17713.6.13.10
A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), incompatibleProductVariants(1), differentSoftwareVersionsRunning(2)  

tDDSynchronizationStatus 1.3.6.1.4.1.17713.6.13.11
An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), holdover(1), holdoverNotConnected(2), acquiringLock(3), noTimingReference(4), timingSystemNotConnected(5), initialising(6), clusterTimingMaster(7), tDDSyncNotActive(8)  

managementPortDisabledWarning 1.3.6.1.4.1.17713.6.13.12
The SNMP ifAdminStatus of the out-of-band management interface has disabled Ethernet traffic
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), disabledBySNMPifAdminStatus(1)  

tDDSynchronizationAlarm 1.3.6.1.4.1.17713.6.13.13
Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), notSynchronized(1), timingSystemFailure(2)  

linkModeOptimizationMismatch 1.3.6.1.4.1.17713.6.13.14
The remote node of this link has been configured with a different link mode optimization
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), linkModeOptimizationMismatch(1)  

managementPortConfigurationMismatch 1.3.6.1.4.1.17713.6.13.15
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(0), mismatchDetected(1)  

secureModeAlarm 1.3.6.1.4.1.17713.6.13.16
The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER secureModeIsActive(0), secureModeIsNotConfigured(1), secureModeIsConfiguredButNotActive(2), secureModeIsNotSupported(3)  

ethernetBridgingStatusAlarm 1.3.6.1.4.1.17713.6.13.17
Ethernet traffic bridging is disabled because the wireless link is not operating at the configured Lowest Ethernet Modulation Mode
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ethernetBridgingEnabled(0), ethernetBridgingDisabled(1)  

sMTPEmailAlert 1.3.6.1.4.1.17713.6.15.1
Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

sMTPServerIPAddress 1.3.6.1.4.1.17713.6.15.2
IP address of the SMTP server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sMTPServerPortNumber 1.3.6.1.4.1.17713.6.15.3
Port number of the SMTP server
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

sMTPSourceEmailAddress 1.3.6.1.4.1.17713.6.15.4
The 'from' email address used when constructing the automatically generated e-mail message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

sMTPDestinationEmailAddress 1.3.6.1.4.1.17713.6.15.5
The 'to' email address used when constructing the automatically generated e-mail message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

sMTPEnabledMessages 1.3.6.1.4.1.17713.6.15.6
This controls which SMTP messages the unit will send
Status: current Access: read-write
OBJECT-TYPE    
  BITS telecomsChannelUpDown(1), managementPortUpDown(2), dataPortUpDown(3), enabledDiagnosticAlarms(4), dFSImpulseInterference(5), dFSChannelChange(6), wirelessLinkUpDown(7)  

sNMPPortNumber 1.3.6.1.4.1.17713.6.16.1
The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

sNMPCommunityString 1.3.6.1.4.1.17713.6.16.2
The SNMP community string. NB: A system reboot is required to activate changes to this attribute
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

sNMPTrapTableNumber 1.3.6.1.4.1.17713.6.16.3
Number of entries in the sNMPTrapTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 2  

sNMPTrapVersion 1.3.6.1.4.1.17713.6.16.5
The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER v1(0), v2c(1)  

sNMPEnabledTraps 1.3.6.1.4.1.17713.6.16.6
This controls which SNMP Traps the unit will send
Status: current Access: read-write
OBJECT-TYPE    
  BITS managementPortUpDown(0), dataPortUpDown(1), authenticationFailure(2), enabledDiagnosticAlarms(3), dFSImpulseInterference(4), dFSChannelChange(5), wirelessLinkUpDown(6), coldStart(7), telecomsChannelUpDown(15)  

enabledDiagnosticAlarms 1.3.6.1.4.1.17713.6.16.7
Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributes
Status: current Access: read-write
OBJECT-TYPE    
  BITS incompatibleMasterAndSlave(0), incompatibleRegionCodes(1), unknown6(2), unknown5(3), unitOutOfCalibration(4), installArmState(5), installStatus(6), regionCode(7), telecomsChannelAStatus(8), dataPortFiberStatus(9), dataPortStatus(10), dataPortDisabledWarning(11), wirelessLinkDisabledWarning(12), sNTPSyncronisationFailed(13), noWirelessChannelAvailable(14), dataPortConfigurationMismatch(15), syslogDisabledWarning(16), linkModeOptimizationMismatch(17), managementPortStatus(18), managementPortDisabledWarning(19), tDDSynchronizationAlarm(20), telecomsChannelBLoopback(21), telecomsChannelALoopback(22), telecomsChannelBStatus(23), ethernetBridgingStatus(26), secureMode(27), syslogClientDisabledWarning(28), managementPortConfigurationMismatch(29), syslogLocalWrapped(30), syslogLocalNearlyFull(31)  

sNMPTrapTableIndex 1.3.6.1.4.1.17713.6.16.4.1.1
SNMP trap value, used to index the SNMPTrapTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..2  

sNMPTrapIPAddress 1.3.6.1.4.1.17713.6.16.4.1.2
The IP address to which all SNMP Traps are sent. An IP Address of 0.0.0.0 disables all TRAP generation. NB: A system reboot is required to activate changes to this attribute.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sNMPTrapPortNumber 1.3.6.1.4.1.17713.6.16.4.1.3
Destination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver. NB: A system reboot is required to activate changes to this attribute.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

sNTPState 1.3.6.1.4.1.17713.6.17.1
SNTP control state
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

sNTPPollInterval 1.3.6.1.4.1.17713.6.17.4
The SNTP server polling interval
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 60..43200  

sNTPSync 1.3.6.1.4.1.17713.6.17.5
If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noSync(0), inSync(1)  

sNTPLastSync 1.3.6.1.4.1.17713.6.17.6
Last SNTP sync time
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

systemClock 1.3.6.1.4.1.17713.6.17.7
System clock presented as local time
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

timeZone 1.3.6.1.4.1.17713.6.17.8
Time zone offsets from Greenwich Mean Time (GMT)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER gmtMinus1200(0), gmtMinus1130(1), gmtMinus1100(2), gmtMinus1030(3), gmtMinus1000(4), gmtMinus0930(5), gmtMinus0900(6), gmtMinus0830(7), gmtMinus0800(8), gmtMinus0730(9), gmtMinus0700(10), gmtMinus0630(11), gmtMinus0600(12), gmtMinus0530(13), gmtMinus0500(14), gmtMinus0430(15), gmtMinus0400(16), gmtMinus0330(17), gmtMinus0300(18), gmtMinus0230(19), gmtMinus0200(20), gmtMinus0130(21), gmtMinus0100(22), gmtMinus0030(23), gmtZero(24), gmtPlus0030(25), gmtPlus0100(26), gmtPlus0130(27), gmtPlus0200(28), gmtPlus0230(29), gmtPlus0300(30), gmtPlus0330(31), gmtPlus0400(32), gmtPlus0430(33), gmtPlus0500(34), gmtPlus0530(35), gmtPlus0600(36), gmtPlus0630(37), gmtPlus0700(38), gmtPlus0730(39), gmtPlus0800(40), gmtPlus0830(41), gmtPlus0900(42), gmtPlus0930(43), gmtPlus1000(44), gmtPlus1030(45), gmtPlus1100(46), gmtPlus1130(47), gmtPlus1200(48), gmtPlus1230(49), gmtPlus1300(50)  

daylightSaving 1.3.6.1.4.1.17713.6.17.9
Daylight Saving Time
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

sNTPPrimaryServer 1.3.6.1.4.1.17713.6.17.10
Specifies the primary SNTP server, determining the order in which the servers are tried.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER server1(0), server2(1)  

sNTPPrimaryServerDeadTime 1.3.6.1.4.1.17713.6.17.11
Time (in seconds) to wait before retrying communications with an unresponsive primary SNTP server. Setting the value to 0 disables the timer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

sNTPServerRetries 1.3.6.1.4.1.17713.6.17.12
Number of times the PTP will retry after an SNTP server fails to respond.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..10  

sNTPServerTimeout 1.3.6.1.4.1.17713.6.17.13
Time (in seconds) the PTP will wait for a response from an SNTP server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

sNTPServerTableNumber 1.3.6.1.4.1.17713.6.17.14
Number of entries in the SNTPServerTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 2  

sNTPServerTableIndex 1.3.6.1.4.1.17713.6.17.15.1.1
Index range for the SNTPServerTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..2  

sNTPServerIPAddress 1.3.6.1.4.1.17713.6.17.15.1.2
The IP address of a valid SNTP server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sNTPServerPortNumber 1.3.6.1.4.1.17713.6.17.15.1.3
The IP port number of the SNTP server. Defaults to port 123.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

sNTPServerStatus 1.3.6.1.4.1.17713.6.17.15.1.4
Status message reflecting the state of communications with the SNTP server
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

systemReset 1.3.6.1.4.1.17713.6.18.1
Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER running(0), consoleReboot(1)  

softwareVersion 1.3.6.1.4.1.17713.6.19.1
Current software version
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

hardwareVersion 1.3.6.1.4.1.17713.6.19.2
Hardware platform version
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

secondarySoftwareVersion 1.3.6.1.4.1.17713.6.19.3
Secondary software version, used when the primary software image is invalid or erased
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

bootVersion 1.3.6.1.4.1.17713.6.19.4
Boot code software version
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

receiveDataRate 1.3.6.1.4.1.17713.6.20.1
Average data rate over the last one second interval (kbps)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

transmitDataRate 1.3.6.1.4.1.17713.6.20.2
Average data rate over the last one second interval (kbps)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

aggregateDataRate 1.3.6.1.4.1.17713.6.20.3
Average data rate over the last one second interval (kbps)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wirelessLinkAvailability 1.3.6.1.4.1.17713.6.20.4
Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000000  

wirelessLinkStatus 1.3.6.1.4.1.17713.6.20.5
Current status of the wireless link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(0), registering(1), searching(2), acquiring(3), radarCAC(4), initialising(5)  

byteErrorRatio 1.3.6.1.4.1.17713.6.20.6
Reciprocal of the byte error ratio calculated since the last reset of the system counters
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

receiveModulationModeDetail 1.3.6.1.4.1.17713.6.20.7
The reason for the current receive modulation mode
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER runningAtMaximumReceiveMode(0), runningAtUserConfiguredMaxModulationMode(1), restrictedBecauseInstallationIsArmed(2), restrictedBecauseOfByteErrorsOnTheWirelessLink(3), restrictedBecauseTheLinkParametersAreUpdating(4), restrictedBecauseDFSchannelChangeIsInProgress(5), restrictedDueToTheLowEthernetLinkSpeed(6), runningAtMaximumReceiveModeForChannelBandwidth(7), limitedByTheWirelessConditions(8)  

ethernetBridgingAvailability 1.3.6.1.4.1.17713.6.20.8
Link availability bridging Ethernet traffic calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000000  

encryptionAlgorithm 1.3.6.1.4.1.17713.6.22.1
The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctly
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), aESRijndael(1), aES256bitRijndael(2)  

tDDSynchronizationMode 1.3.6.1.4.1.17713.6.23.1
TDD Synchronization Mode selection
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

syslogClient 1.3.6.1.4.1.17713.6.24.1
Enable or disable the syslog client
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

syslogState 1.3.6.1.4.1.17713.6.24.2
The syslog service has been enabled or disabled
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

longitude 1.3.6.1.4.1.17713.6.96.1
The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..19)  

latitude 1.3.6.1.4.1.17713.6.96.2
The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..19)  

altitude 1.3.6.1.4.1.17713.6.96.3
The altitude of the unit, measured in metres. This object is set by the SNMP manager and has no internal function.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

dfsChannelChangeTrap 1.3.6.1.4.1.17713.6.99.0.1
DFS channel change event
Status: current Access: read-write
NOTIFICATION-TYPE    

dfsImpulsiveInterferenceTrap 1.3.6.1.4.1.17713.6.99.0.2
DFS impulsive interference detected event
Status: current Access: read-write
NOTIFICATION-TYPE    

dataPortStatusTrap 1.3.6.1.4.1.17713.6.99.0.3
Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

telecomsChannelAStatusTrap 1.3.6.1.4.1.17713.6.99.0.4
Current status of telecoms channel A. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

telecomsChannelBStatusTrap 1.3.6.1.4.1.17713.6.99.0.5
Current status of telecoms channel B. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

channelALoopbackTrap 1.3.6.1.4.1.17713.6.99.0.6
The loopback status of telecoms channel A. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

channelBLoopbackTrap 1.3.6.1.4.1.17713.6.99.0.7
The loopback status of telecoms channel B. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

regionCodeTrap 1.3.6.1.4.1.17713.6.99.0.8
The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted license key. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

installStatusTrap 1.3.6.1.4.1.17713.6.99.0.9
A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

installArmStateTrap 1.3.6.1.4.1.17713.6.99.0.10
Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

unitOutOfCalibrationTrap 1.3.6.1.4.1.17713.6.99.0.11
The unit is out of calibration
Status: current Access: read-write
NOTIFICATION-TYPE    

encryptionEnabledMismatchTrap 1.3.6.1.4.1.17713.6.99.0.13
Encryption has been enabled on one end of the wireless link but not the other
Status: current Access: read-write
NOTIFICATION-TYPE    

incompatibleRegionCodesTrap 1.3.6.1.4.1.17713.6.99.0.14
The master and slave units have incompatible region codes. NB: Both units must have compatible license keys
Status: current Access: read-write
NOTIFICATION-TYPE    

noWirelessChannelAvailableTrap 1.3.6.1.4.1.17713.6.99.0.15
Spectrum Management was unable to locate a suitable wireless channel to operate on
Status: current Access: read-write
NOTIFICATION-TYPE    

wirelessLinkDisabledWarningTrap 1.3.6.1.4.1.17713.6.99.0.16
The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic
Status: current Access: read-write
NOTIFICATION-TYPE    

dataPortDisabledWarningTrap 1.3.6.1.4.1.17713.6.99.0.17
The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic
Status: current Access: read-write
NOTIFICATION-TYPE    

dataPortFiberStatusTrap 1.3.6.1.4.1.17713.6.99.0.18
If the fiber link is not OK, there are three possible causes: Either the fiber link has been installed but disabled (because the license key does not include fiber support), the link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), or the link could not be established and LOS is detected (i.e. no optical carrier is detected). NB: a change of status may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

dataPortConfigurationMismatchTrap 1.3.6.1.4.1.17713.6.99.0.19
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch
Status: current Access: read-write
NOTIFICATION-TYPE    

incompatibleMasterAndSlaveTrap 1.3.6.1.4.1.17713.6.99.0.20
A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

sNTPSyncTrap 1.3.6.1.4.1.17713.6.99.0.21
If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP
Status: current Access: read-write
NOTIFICATION-TYPE    

tDDSynchronizationAlarmTrap 1.3.6.1.4.1.17713.6.99.0.22
Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.
Status: current Access: read-write
NOTIFICATION-TYPE    

managementPortStatusTrap 1.3.6.1.4.1.17713.6.99.0.23
Current status of the out-of-band management link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

managementPortDisabledWarningTrap 1.3.6.1.4.1.17713.6.99.0.24
The SNMP ifAdminStatus of the out-of-band management interface has disabled Ethernet traffic
Status: current Access: read-write
NOTIFICATION-TYPE    

linkModeOptimizationMismatchTrap 1.3.6.1.4.1.17713.6.99.0.25
The remote node of this link has been configured with a different link mode optimization
Status: current Access: read-write
NOTIFICATION-TYPE    

managementPortConfigurationMismatchTrap 1.3.6.1.4.1.17713.6.99.0.28
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.
Status: current Access: read-write
NOTIFICATION-TYPE    

syslogStateTrap 1.3.6.1.4.1.17713.6.99.0.30
The syslog service has been enabled or disabled
Status: current Access: read-write
NOTIFICATION-TYPE    

syslogLocalNearlyFullTrap 1.3.6.1.4.1.17713.6.99.0.31
The syslog local log is nearly full (90%)
Status: current Access: read-write
NOTIFICATION-TYPE    

syslogLocalWrappedTrap 1.3.6.1.4.1.17713.6.99.0.32
The syslog local log has wrapped
Status: current Access: read-write
NOTIFICATION-TYPE    

syslogClientTrap 1.3.6.1.4.1.17713.6.99.0.33
Enable or disable the syslog client
Status: current Access: read-write
NOTIFICATION-TYPE    

secureModeAlarmTrap 1.3.6.1.4.1.17713.6.99.0.34
The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image.
Status: current Access: read-write
NOTIFICATION-TYPE    

ethernetBridgingStatusAlarmTrap 1.3.6.1.4.1.17713.6.99.0.35
Ethernet traffic bridging is disabled because the wireless link is not operating at the configured Lowest Ethernet Modulation Mode
Status: current Access: read-write
NOTIFICATION-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor