CES-BGP-DEFAULTS-MIB

File: CES-BGP-DEFAULTS-MIB.mib (39256 bytes)

Imported modules

SNMPv2-SMI RFC1213-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
IpAddress Integer32 Counter32
Gauge32 mib-2

Defined Types

BgpPeerEntry  
SEQUENCE    
  bgpPeerIdentifier IpAddress
  bgpPeerState INTEGER
  bgpPeerAdminStatus INTEGER
  bgpPeerNegotiatedVersion Integer32
  bgpPeerLocalAddr IpAddress
  bgpPeerLocalPort INTEGER
  bgpPeerRemoteAddr IpAddress
  bgpPeerRemotePort INTEGER
  bgpPeerRemoteAs INTEGER
  bgpPeerInUpdates Counter32
  bgpPeerOutUpdates Counter32
  bgpPeerInTotalMessages Counter32
  bgpPeerOutTotalMessages Counter32
  bgpPeerLastError OCTET STRING
  bgpPeerFsmEstablishedTransitions Counter32
  bgpPeerFsmEstablishedTime Gauge32
  bgpPeerConnectRetryInterval INTEGER
  bgpPeerHoldTime INTEGER
  bgpPeerKeepAlive INTEGER
  bgpPeerHoldTimeConfigured INTEGER
  bgpPeerKeepAliveConfigured INTEGER
  bgpPeerMinASOriginationInterval INTEGER
  bgpPeerMinRouteAdvertisementInterval INTEGER
  bgpPeerInUpdateElapsedTime Gauge32

BgpPathAttrEntry  
SEQUENCE    
  bgpPathAttrPeer IpAddress
  bgpPathAttrDestNetwork IpAddress
  bgpPathAttrOrigin INTEGER
  bgpPathAttrASPath OCTET STRING
  bgpPathAttrNextHop IpAddress
  bgpPathAttrInterASMetric Integer32

Bgp4PathAttrEntry  
SEQUENCE    
  bgp4PathAttrPeer IpAddress
  bgp4PathAttrIpAddrPrefixLen INTEGER
  bgp4PathAttrIpAddrPrefix IpAddress
  bgp4PathAttrOrigin INTEGER
  bgp4PathAttrASPathSegment OCTET STRING
  bgp4PathAttrNextHop IpAddress
  bgp4PathAttrMultiExitDisc INTEGER
  bgp4PathAttrLocalPref INTEGER
  bgp4PathAttrAtomicAggregate INTEGER
  bgp4PathAttrAggregatorAS INTEGER
  bgp4PathAttrAggregatorAddr IpAddress
  bgp4PathAttrCalcLocalPref INTEGER
  bgp4PathAttrBest INTEGER
  bgp4PathAttrUnknown OCTET STRING

Defined Values

bgp 1.3.6.1.2.1.15
The MIB module for BGP-4.
MODULE-IDENTITY    

bgpVersion 1.3.6.1.2.1.15.1
Vector of supported BGP protocol version numbers. Each peer negotiates the version from this vector. Versions are identified via the string of bits contained within this object. The first octet contains bits 0 to 7, the second octet contains bits 8 to 15, and so on, with the most significant bit referring to the lowest bit number in the octet (e.g., the MSB of the first octet refers to bit 0). If a bit, i, is present and set, then the version (i+1) of the BGP is supported.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..255)  

bgpLocalAs 1.3.6.1.2.1.15.2
The local autonomous system number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bgpPeerTable 1.3.6.1.2.1.15.3
BGP peer table. This table contains, one entry per BGP peer, information about the connections with BGP peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BgpPeerEntry

bgpPeerEntry 1.3.6.1.2.1.15.3.1
Entry containing information about the connection with a BGP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  BgpPeerEntry  

bgpPeerIdentifier 1.3.6.1.2.1.15.3.1.1
The BGP Identifier of this entry's BGP peer.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bgpPeerState 1.3.6.1.2.1.15.3.1.2
The BGP peer connection state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER idle(1), connect(2), active(3), opensent(4), openconfirm(5), established(6)  

bgpPeerAdminStatus 1.3.6.1.2.1.15.3.1.3
The desired state of the BGP connection. A transition from 'stop' to 'start' will cause the BGP Start Event to be generated. A transition from 'start' to 'stop' will cause the BGP Stop Event to be generated. This parameter can be used to restart BGP peer connections. Care should be used in providing write access to this object without adequate authentication.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stop(1), start(2)  

bgpPeerNegotiatedVersion 1.3.6.1.2.1.15.3.1.4
The negotiated version of BGP running between the two peers.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bgpPeerLocalAddr 1.3.6.1.2.1.15.3.1.5
The local IP address of this entry's BGP connection.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bgpPeerLocalPort 1.3.6.1.2.1.15.3.1.6
The local port for the TCP connection between the BGP peers.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bgpPeerRemoteAddr 1.3.6.1.2.1.15.3.1.7
The remote IP address of this entry's BGP peer.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bgpPeerRemotePort 1.3.6.1.2.1.15.3.1.8
The remote port for the TCP connection between the BGP peers. Note that the objects bgpPeerLocalAddr, bgpPeerLocalPort, bgpPeerRemoteAddr and bgpPeerRemotePort provide the appropriate reference to the standard MIB TCP connection table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bgpPeerRemoteAs 1.3.6.1.2.1.15.3.1.9
The remote autonomous system number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bgpPeerInUpdates 1.3.6.1.2.1.15.3.1.10
The number of BGP UPDATE messages received on this connection. This object should be initialized to zero (0) when the connection is established.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bgpPeerOutUpdates 1.3.6.1.2.1.15.3.1.11
The number of BGP UPDATE messages transmitted on this connection. This object should be initialized to zero (0) when the connection is established.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bgpPeerInTotalMessages 1.3.6.1.2.1.15.3.1.12
The total number of messages received from the remote peer on this connection. This object should be initialized to zero when the connection is established.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bgpPeerOutTotalMessages 1.3.6.1.2.1.15.3.1.13
The total number of messages transmitted to the remote peer on this connection. This object should be initialized to zero when the connection is established.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bgpPeerLastError 1.3.6.1.2.1.15.3.1.14
The last error code and subcode seen by this peer on this connection. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

bgpPeerFsmEstablishedTransitions 1.3.6.1.2.1.15.3.1.15
The total number of times the BGP FSM transitioned into the established state.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bgpPeerFsmEstablishedTime 1.3.6.1.2.1.15.3.1.16
This timer indicates how long (in seconds) this peer has been in the Established state or how long since this peer was last in the Established state. It is set to zero when a new peer is configured or the router is booted.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

bgpPeerConnectRetryInterval 1.3.6.1.2.1.15.3.1.17
Time interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

bgpPeerHoldTime 1.3.6.1.2.1.15.3.1.18
Time interval in seconds for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker by using the smaller of the value in bgpPeerHoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at lease three seconds if it is not zero (0) in which case the Hold Timer has not been established with the peer, or, the value of bgpPeerHoldTimeConfigured is zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0 | 3..65535  

bgpPeerKeepAlive 1.3.6.1.2.1.15.3.1.19
Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with bgpPeerHoldTime, it has the same proportion as what bgpPeerKeepAliveConfigured has when compared with bgpPeerHoldTimeConfigured. If the value of this object is zero (0), it indicates that the KeepAlive timer has not been established with the peer, or, the value of bgpPeerKeepAliveConfigured is zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0 | 1..21845  

bgpPeerHoldTimeConfigured 1.3.6.1.2.1.15.3.1.20
Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (bgpPeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0 | 3..65535  

bgpPeerKeepAliveConfigured 1.3.6.1.2.1.15.3.1.21
Time interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by bgpPeerKeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of bgpPeerHoldTimeConfigured. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0 | 1..21845  

bgpPeerMinASOriginationInterval 1.3.6.1.2.1.15.3.1.22
Time interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

bgpPeerMinRouteAdvertisementInterval 1.3.6.1.2.1.15.3.1.23
Time interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

bgpPeerInUpdateElapsedTime 1.3.6.1.2.1.15.3.1.24
Elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time bgpPeerInUpdates is incremented, the value of this object is set to zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

bgpIdentifier 1.3.6.1.2.1.15.4
The BGP Identifier of local system.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bgpRcvdPathAttrTable 1.3.6.1.2.1.15.5
The BGP Received Path Attribute Table contains information about paths to destination networks received from all peers running BGP version 3 or less.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BgpPathAttrEntry

bgpPathAttrEntry 1.3.6.1.2.1.15.5.1
Information about a path to a network.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  BgpPathAttrEntry  

bgpPathAttrPeer 1.3.6.1.2.1.15.5.1.1
The IP address of the peer where the path information was learned.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

bgpPathAttrDestNetwork 1.3.6.1.2.1.15.5.1.2
The address of the destination network.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

bgpPathAttrOrigin 1.3.6.1.2.1.15.5.1.3
The ultimate origin of the path information.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER igp(1), egp(2), incomplete(3)  

bgpPathAttrASPath 1.3.6.1.2.1.15.5.1.4
The set of ASs that must be traversed to reach the network. This object is probably best represented as SEQUENCE OF INTEGER. For SMI compatibility, though, it is represented as OCTET STRING. Each AS is represented as a pair of octets according to the following algorithm: first-byte-of-pair = ASNumber / 256; second-byte-of-pair = ASNumber & 255;
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2..255)  

bgpPathAttrNextHop 1.3.6.1.2.1.15.5.1.5
The address of the border router that should be used for the destination network.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

bgpPathAttrInterASMetric 1.3.6.1.2.1.15.5.1.6
The optional inter-AS metric. If this attribute has not been provided for this route, the value for this object is 0.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32  

bgp4PathAttrTable 1.3.6.1.2.1.15.6
The BGP-4 Received Path Attribute Table contains information about paths to destination networks received from all BGP4 peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Bgp4PathAttrEntry

bgp4PathAttrEntry 1.3.6.1.2.1.15.6.1
Information about a path to a network.
Status: current Access: not-accessible
OBJECT-TYPE    
  Bgp4PathAttrEntry  

bgp4PathAttrPeer 1.3.6.1.2.1.15.6.1.1
The IP address of the peer where the path information was learned.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bgp4PathAttrIpAddrPrefixLen 1.3.6.1.2.1.15.6.1.2
Length in bits of the IP address prefix in the Network Layer Reachability Information field.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..32  

bgp4PathAttrIpAddrPrefix 1.3.6.1.2.1.15.6.1.3
An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by bgp4PathAttrIpAddrPrefixLen. Any bits beyond the length specified by bgp4PathAttrIpAddrPrefixLen are zeroed.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bgp4PathAttrOrigin 1.3.6.1.2.1.15.6.1.4
The ultimate origin of the path information.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER igp(1), egp(2), incomplete(3)  

bgp4PathAttrASPathSegment 1.3.6.1.2.1.15.6.1.5
The sequence of AS path segments. Each AS path segment is represented by a triple <type, length, value>. The type is a 1-octet field which has two possible values: 1 AS_SET: unordered set of ASs a route in the UPDATE message has traversed 2 AS_SEQUENCE: ordered set of ASs a route in the UPDATE message has traversed. The length is a 1-octet field containing the number of ASs in the value field. The value field contains one or more AS numbers, each AS is represented in the octet string as a pair of octets according to the following algorithm: first-byte-of-pair = ASNumber / 256; second-byte-of-pair = ASNumber & 255;
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2..255)  

bgp4PathAttrNextHop 1.3.6.1.2.1.15.6.1.6
The address of the border router that should be used for the destination network.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bgp4PathAttrMultiExitDisc 1.3.6.1.2.1.15.6.1.7
This metric is used to discriminate between multiple exit points to an adjacent autonomous system. A value of -1 indicates the absence of this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -1..2147483647  

bgp4PathAttrLocalPref 1.3.6.1.2.1.15.6.1.8
The originating BGP4 speaker's degree of preference for an advertised route. A value of -1 indicates the absence of this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -1..2147483647  

bgp4PathAttrAtomicAggregate 1.3.6.1.2.1.15.6.1.9
Whether or not the local system has selected a less specific route without selecting a more specific route.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER lessSpecificRrouteNotSelected(1), lessSpecificRouteSelected(2)  

bgp4PathAttrAggregatorAS 1.3.6.1.2.1.15.6.1.10
The AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

bgp4PathAttrAggregatorAddr 1.3.6.1.2.1.15.6.1.11
The IP address of the last BGP4 speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

bgp4PathAttrCalcLocalPref 1.3.6.1.2.1.15.6.1.12
The degree of preference calculated by the receiving BGP4 speaker for an advertised route. A value of -1 indicates the absence of this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -1..2147483647  

bgp4PathAttrBest 1.3.6.1.2.1.15.6.1.13
An indication of whether or not this route was chosen as the best BGP4 route.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER false(1), true(2)  

bgp4PathAttrUnknown 1.3.6.1.2.1.15.6.1.14
One or more path attributes not understood by this BGP4 speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if any, are not recorded by this object.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

bgpTraps 1.3.6.1.2.1.15.7
OBJECT IDENTIFIER    

bgpEstablished 1.3.6.1.2.1.15.7.1
The BGP Established event is generated when the BGP FSM enters the ESTABLISHED state.
Status: current Access: read-only
NOTIFICATION-TYPE    

bgpBackwardTransition 1.3.6.1.2.1.15.7.2
The BGPBackwardTransition Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state.
Status: current Access: read-only
NOTIFICATION-TYPE