CIE1000-LLDP-MIB

File: CIE1000-LLDP-MIB.mib (89623 bytes)

Imported modules

SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
CISCO-IE1000-MIB CIE1000-TC

Imported symbols

NOTIFICATION-GROUP MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-TYPE MODULE-IDENTITY OBJECT-TYPE
TEXTUAL-CONVENTION cie1000SwitchMgmt CIE1000DisplayString
CIE1000Integer64 CIE1000InterfaceIndex CIE1000RowEditorState
CIE1000Unsigned16 CIE1000Unsigned64 CIE1000Unsigned8
Integer32 Unsigned32 TruthValue

Defined Types

CIE1000lldpAdminState  
This enumerations the admin state.
TEXTUAL-CONVENTION    
  INTEGER disabled(0), txAndRx(1), txOnly(2), rxOnly(3)  

CIE1000lldpmedAltitudeType  
This enumerations the altitude type.
TEXTUAL-CONVENTION    
  INTEGER meters(1), floors(2)  

CIE1000lldpmedCivicAddressType  
This enumerations the civic address type.
TEXTUAL-CONVENTION    
  INTEGER state(1), county(2), city(3), district(4), block(5), street(6), leadingStreetDirection(16), trailingStreetSuffix(17), streetSuffix(18), houseNo(19), houseNoSuffix(20), landmark(21), additionalInfo(22), name(23), zipCode(24), building(25), apartment(26), floor(27), roomNumber(28), placeType(29), postalCommunityName(30), poBox(31), additionalCode(32)  

CIE1000lldpmedDatumType  
This enumerations the datum (geodetic system).
TEXTUAL-CONVENTION    
  INTEGER wgs84(1), nad83navd88(2), nad83mllw(3)  

CIE1000lldpmedDeviceType  
This enumerations the device type that the device shall operate as.
TEXTUAL-CONVENTION    
  INTEGER connectivity(0), endpoint(1)  

CIE1000lldpmedRemoteDeviceType  
This enumerations the remote neighbor's device type.
TEXTUAL-CONVENTION    
  INTEGER notDefined(0), endpointClassI(1), endpointClassII(2), endpointClassIII(3), networkConnectivity(4), reserved(5)  

CIE1000lldpmedRemoteNetworkPolicyApplicationType  
This enumerations the remote neighbor's network policy's application type.
TEXTUAL-CONVENTION    
  INTEGER voice(1), voiceSignaling(2), guestVoice(3), guestVoiceSignaling(4), softphoneVoice(5), videoConferencing(6), streamingVideo(7), videoSignaling(8)  

CIE1000LldpConfigEntry  
SEQUENCE    
  cie1000LldpConfigIfIndex CIE1000InterfaceIndex
  cie1000LldpConfigAdminState CIE1000lldpAdminState
  cie1000LldpConfigCdpAware TruthValue
  cie1000LldpConfigOptionalTlvs CIE1000Unsigned8
  cie1000LldpConfigSnmpNotificationEna TruthValue

CIE1000LldpConfigMedEntry  
SEQUENCE    
  cie1000LldpConfigMedIfIndex CIE1000InterfaceIndex
  cie1000LldpConfigMedOptionalTlvs CIE1000Unsigned8
  cie1000LldpConfigMedDeviceType CIE1000lldpmedDeviceType

CIE1000LldpConfigMedPolicyEntry  
SEQUENCE    
  cie1000LldpConfigMedPolicyLldpmedPolicy Integer32
  cie1000LldpConfigMedPolicyApplicationType CIE1000lldpmedRemoteNetworkPolicyApplicationType
  cie1000LldpConfigMedPolicyTagged TruthValue
  cie1000LldpConfigMedPolicyVlanId CIE1000Unsigned16
  cie1000LldpConfigMedPolicyL2Priority CIE1000Unsigned8
  cie1000LldpConfigMedPolicyDscp CIE1000Unsigned8
  cie1000LldpConfigMedPolicyAction CIE1000RowEditorState

CIE1000LldpConfigMedPolicyListEntry  
SEQUENCE    
  cie1000LldpConfigMedPolicyListIfIndex CIE1000InterfaceIndex
  cie1000LldpConfigMedPolicyListLldpmedPolicy Integer32
  cie1000LldpConfigMedPolicyListLldpmedPoliciesList TruthValue

CIE1000LldpConfigMedLocationInfEntry  
SEQUENCE    
  cie1000LldpConfigMedLocationInfLldpmedIndex CIE1000lldpmedCivicAddressType
  cie1000LldpConfigMedLocationInfCivicAddress CIE1000DisplayString

CIE1000LldpStatusStatisticsEntry  
SEQUENCE    
  cie1000LldpStatusStatisticsIfIndex CIE1000InterfaceIndex
  cie1000LldpStatusStatisticsTxTotal Unsigned32
  cie1000LldpStatusStatisticsRxTotal Unsigned32
  cie1000LldpStatusStatisticsRxError Unsigned32
  cie1000LldpStatusStatisticsRxDiscarded Unsigned32
  cie1000LldpStatusStatisticsTLVsDiscarded Unsigned32
  cie1000LldpStatusStatisticsTLVsUnrecognized Unsigned32
  cie1000LldpStatusStatisticsTLVsOrgDiscarded Unsigned32
  cie1000LldpStatusStatisticsAgeOuts Unsigned32

CIE1000LldpStatusNeighborsInfEntry  
SEQUENCE    
  cie1000LldpStatusNeighborsInfIfIndex CIE1000InterfaceIndex
  cie1000LldpStatusNeighborsInfLldpmedIndex Integer32
  cie1000LldpStatusNeighborsInfChassisId CIE1000DisplayString
  cie1000LldpStatusNeighborsInfPortId CIE1000DisplayString
  cie1000LldpStatusNeighborsInfPortDescription CIE1000DisplayString
  cie1000LldpStatusNeighborsInfSystemName CIE1000DisplayString
  cie1000LldpStatusNeighborsInfSystemDescription CIE1000DisplayString
  cie1000LldpStatusNeighborsInfSystemCapabilities CIE1000Unsigned16
  cie1000LldpStatusNeighborsInfSystemCapabilitiesEnable CIE1000Unsigned16

CIE1000LldpStatusNeighborsMgmtInfEntry  
SEQUENCE    
  cie1000LldpStatusNeighborsMgmtInfIfIndex CIE1000InterfaceIndex
  cie1000LldpStatusNeighborsMgmtInfLldpmedIndex Integer32
  cie1000LldpStatusNeighborsMgmtInfLldpManagement Integer32
  cie1000LldpStatusNeighborsMgmtInfSystemMgmAddressSubtype CIE1000Unsigned8
  cie1000LldpStatusNeighborsMgmtInfSystemMgmtAddress CIE1000DisplayString
  cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterfaceSubtype Integer32
  cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterface Integer32
  cie1000LldpStatusNeighborsMgmtInfSystemMgmtOid OBJECT IDENTIFIER

CIE1000LldpStatusMedRemoteDeviceInfoEntry  
SEQUENCE    
  cie1000LldpStatusMedRemoteDeviceInfoIfIndex CIE1000InterfaceIndex
  cie1000LldpStatusMedRemoteDeviceInfoLldpmedIndex Integer32
  cie1000LldpStatusMedRemoteDeviceInfoCapabilities CIE1000Unsigned16
  cie1000LldpStatusMedRemoteDeviceInfoCapabilitiesEnabled CIE1000Unsigned16
  cie1000LldpStatusMedRemoteDeviceInfoLatitude CIE1000Integer64
  cie1000LldpStatusMedRemoteDeviceInfoLongitude CIE1000Integer64
  cie1000LldpStatusMedRemoteDeviceInfoAltitudeType CIE1000lldpmedAltitudeType
  cie1000LldpStatusMedRemoteDeviceInfoAltitude Integer32
  cie1000LldpStatusMedRemoteDeviceInfoDatum CIE1000lldpmedDatumType
  cie1000LldpStatusMedRemoteDeviceInfoElinaddr CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceInfoDeviceType CIE1000lldpmedRemoteDeviceType
  cie1000LldpStatusMedRemoteDeviceInfoHwRev CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceInfoFwRev CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceInfoSwRev CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceInfoSerialNo CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceInfoManufacturerName CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceInfoModelName CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceInfoAssetId CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSys CIE1000Unsigned16
  cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSys CIE1000Unsigned16
  cie1000LldpStatusMedRemoteDeviceInfoEeeFbTwSys CIE1000Unsigned16
  cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSysEcho CIE1000Unsigned16
  cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSysEcho CIE1000Unsigned16

CIE1000LldpStatusMedRemoteDeviceLocInfoEntry  
SEQUENCE    
  cie1000LldpStatusMedRemoteDeviceLocInfoIfIndex CIE1000InterfaceIndex
  cie1000LldpStatusMedRemoteDeviceLocInfoLldpmedIndex Integer32
  cie1000LldpStatusMedRemoteDeviceLocInfoState CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoCounty CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoCity CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoDistrict CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoBlock CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoStreet CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoLeadingStreetDirection CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoTrailingStreetSuffix CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoStreetSuffix CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoHouseNo CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoHouseNoSuffix CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoLandmark CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalInfo CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoName CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoZipCode CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoBuilding CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoApartment CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoFloor CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoRoomNumber CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoPlaceType CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoPostalCommunityName CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoPoBox CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalCode CIE1000DisplayString
  cie1000LldpStatusMedRemoteDeviceLocInfoCountryCode CIE1000DisplayString

CIE1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry  
SEQUENCE    
  cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoIfIndex CIE1000InterfaceIndex
  cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedIndex Integer32
  cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedPolicy Integer32
  cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoApplicationType CIE1000lldpmedRemoteNetworkPolicyApplicationType
  cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoUnknownPolicy TruthValue
  cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTagged TruthValue
  cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoVlanId CIE1000Unsigned16
  cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoL2Priority CIE1000Unsigned8
  cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoDscp CIE1000Unsigned8

CIE1000LldpControlStatisticsClearEntry  
SEQUENCE    
  cie1000LldpControlStatisticsClearIfIndex CIE1000InterfaceIndex
  cie1000LldpControlStatisticsClearStatisticsClear TruthValue

Defined Values

cie1000LldpMib 1.3.6.1.4.1.9.9.832.1.34
This is a private version of the LLDP MIB
MODULE-IDENTITY    

cie1000LldpMibObjects 1.3.6.1.4.1.9.9.832.1.34.1
OBJECT IDENTIFIER    

cie1000LldpConfig 1.3.6.1.4.1.9.9.832.1.34.1.2
OBJECT IDENTIFIER    

cie1000LldpConfigGlobal 1.3.6.1.4.1.9.9.832.1.34.1.2.1
OBJECT IDENTIFIER    

cie1000LldpConfigGlobalReInitDelay 1.3.6.1.4.1.9.9.832.1.34.1.2.1.1
Set the LLDP tx reinitialization delay in seconds. Valid range 1-10. When a port is disabled, LLDP is disabled or the switch is rebooted, a LLDP shutdown frame is transmitted to the neighboring units, signaling that the LLDP information isn't valid anymore. Tx reinitialization delay controls the amount of seconds between the shutdown frame and a new LLDP initialization.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpConfigGlobalMsgTxHold 1.3.6.1.4.1.9.9.832.1.34.1.2.1.2
Set the LLDP tx hold times . Valid range 2-10. Each LLDP frame contains information about how long time the information in the LLDP frame shall be considered valid. The LLDP information valid period is set to tx hold times multiplied by tx interval seconds.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpConfigGlobalMsgTxInterval 1.3.6.1.4.1.9.9.832.1.34.1.2.1.3
Set the LLDP tx interval in seconds. The switch periodically transmits LLDP frames to its neighbors for having the network discovery information up-to-date. The interval between each LLDP frame is determined by the tx Interval value. Valid range 5-32768 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpConfigGlobalTxDelay 1.3.6.1.4.1.9.9.832.1.34.1.2.1.4
Set the LLDP tx delay in seconds. Valid range 1-8192. If some configuration is changed (e.g. the IP address) a new LLDP frame is transmitted, but the time between the LLDP frames will always be at least the value of tx delay seconds. Note: tx Delay cannot be larger than 1/4 of the tx interval.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpConfigTable 1.3.6.1.4.1.9.9.832.1.34.1.2.2
This is a table to configure LLDP configurations for a specific interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpConfigEntry

cie1000LldpConfigEntry 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1
Each interface has a set of control parameters
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpConfigEntry  

cie1000LldpConfigIfIndex 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.1
Logical interface number index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000LldpConfigAdminState 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.3
Sets the LLDP admin state for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000lldpAdminState  

cie1000LldpConfigCdpAware 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.4
Enables/disables CDP awareness for the interface. CDP is Cisco's equivalent to LLDP. The CDP operation is restricted to decoding incoming CDP frames (The switch doesn't transmit CDP frames). CDP frames are only decoded if LLDP on the port is enabled. Only CDP TLVs that can be mapped to a corresponding field in the LLDP neighbors' table are decoded. All other TLVs are discarded (Unrecognized CDP TLVs and discarded CDP frames are not shown in the LLDP statistics.). CDP TLVs are mapped onto LLDP neighbors' table as shown below. CDP TLV 'Device ID' is mapped to the LLDP 'Chassis ID' field. CDP TLV 'Address' is mapped to the LLDP 'Management Address' field. The CDP address TLV can contain multiple addresses, but only the first address is shown in the LLDP neighbors table. CDP TLV 'Port ID' is mapped to the LLDP 'Port ID' field. CDP TLV 'Version and Platform' is mapped to the LLDP 'System Description' field. Both the CDP and LLDP support 'system capabilities', but the CDP capabilities cover capabilities that are not part of the LLDP. These capabilities are shown as 'others' in the LLDP neighbors' table. If all ports have CDP awareness disabled the switch forwards CDP frames received from neighbor devices. If at least one port has CDP awareness enabled all CDP frames are terminated by the switch. Note: When CDP awareness on a port is disabled the CDP information isn't removed immediately, but gets removed when the hold time is exceeded.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cie1000LldpConfigOptionalTlvs 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.5
Enables/Disables the LLDP optional TLVs. Bit mask, where setting the bit to 1 means enable transmission of the corresponding TLV. Bit 0 represents Port Description TLV. Bit 1 represents System Name TLV. Bit 2 represents System Description. Bit 3 represents System Capabilities TLV. Bit 4 represents Management Address TLV.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned8  

cie1000LldpConfigSnmpNotificationEna 1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.6
Enable/disable of SNMP Trap notification.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cie1000LldpConfigMed 1.3.6.1.4.1.9.9.832.1.34.1.2.3
OBJECT IDENTIFIER    

cie1000LldpConfigMedTable 1.3.6.1.4.1.9.9.832.1.34.1.2.3.1
This is a table to configure LLDP MEDIA configurations for a specific interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpConfigMedEntry

cie1000LldpConfigMedEntry 1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1
Each interface has a set of control parameters
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpConfigMedEntry  

cie1000LldpConfigMedIfIndex 1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1.1
Logical interface number index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000LldpConfigMedOptionalTlvs 1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1.3
Enables/Disables the LLDP optional TLVs. Bit mask, where setting the bit to 1 means enable transmission of the corresponding optional TLV. Bit 0 represents the capabilities TLV. Bit 1 represents the network Policy TLV. Bit 2 represents the location TLV. Bit 3 represents the PoE TLV.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned8  

cie1000LldpConfigMedDeviceType 1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1.4
Setting device type to configure the mode the device shall operate as.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000lldpmedDeviceType  

cie1000LldpConfigMedPolicyTable 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2
This is a table to configure LLDP MED Policies for the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpConfigMedPolicyEntry

cie1000LldpConfigMedPolicyEntry 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1
Network Policy Discovery enables the efficient discovery and diagnosis of mismatch issues with the VLAN configuration, along with the associated Layer 2 and Layer 3 attributes, which apply for a set of specific protocol applications on that port. Improper network policy configurations are a very significant issue in VoIP environments that frequently result in voice quality degradation or loss of service. Policies are only intended for use with applications that have specific 'real-time' network policy requirements, such as interactive voice and/or video services.
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpConfigMedPolicyEntry  

cie1000LldpConfigMedPolicyLldpmedPolicy 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.1
Policy index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..31  

cie1000LldpConfigMedPolicyApplicationType 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.3
The LLDP policy application type.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000lldpmedRemoteNetworkPolicyApplicationType  

cie1000LldpConfigMedPolicyTagged 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.4
The LLDP policy tagged flag. Defines if LLDP policy uses tagged VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cie1000LldpConfigMedPolicyVlanId 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.5
The LLDP policy VLAN ID. Only valid when policy 'Tagged' is TRUE
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned16 1..4095  

cie1000LldpConfigMedPolicyL2Priority 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.6
The LLDP policy L2 priority.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned8 0..7  

cie1000LldpConfigMedPolicyDscp 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.7
The LLDP policy DSCP.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned8 0..63  

cie1000LldpConfigMedPolicyAction 1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.100
Action
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000RowEditorState  

cie1000LldpConfigMedPolicyListTable 1.3.6.1.4.1.9.9.832.1.34.1.2.3.3
Each interface can be mapped to multiple policies. Set to TRUE in order to enable the corresponding policy to be transmitted at the interface. It is a requirement that the policy is defined.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpConfigMedPolicyListEntry

cie1000LldpConfigMedPolicyListEntry 1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1
Each location information has a control parameter
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpConfigMedPolicyListEntry  

cie1000LldpConfigMedPolicyListIfIndex 1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1.1
Logical interface number index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000LldpConfigMedPolicyListLldpmedPolicy 1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1.3
Policy index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..31  

cie1000LldpConfigMedPolicyListLldpmedPoliciesList 1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1.4
Set to TRUE assign the corresponding policy index to the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cie1000LldpConfigMedGlobal 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4
OBJECT IDENTIFIER    

cie1000LldpConfigMedGlobalFastRepeatCount 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.1
Number of times to repeat LLDP frame transmission at fast start Rapid startup and Emergency Call Service Location Identification Discovery of endpoints is a critically important aspect of VoIP systems in general. In addition, it is best to advertise only those pieces of information which are specifically relevant to particular endpoint types (for example only advertise the voice network policy to permitted voice-capable devices), both in order to conserve the limited LLDPU space and to reduce security and system integrity issues that can come with inappropriate knowledge of the network policy. With this in mind LLDP-MED defines an LLDP-MED Fast Start interaction between the protocol and the application layers on top of the protocol, in order to achieve these related properties. Initially, a Network Connectivity Device will only transmit LLDP TLVs in an LLDPDU. Only after an LLDP-MED Endpoint Device is detected, will an LLDP-MED capable Network Connectivity Device start to advertise LLDP-MED TLVs in outgoing LLDPDUs on the associated port. The LLDP-MED application will temporarily speed up the transmission of the LLDPDU to start within a second, when a new LLDP-MED neighbor has been detected in order share LLDP-MED information as fast as possible to new neighbors. Because there is a risk of an LLDP frame being lost during transmission between neighbors, it is recommended to repeat the fast start transmission multiple times to increase the possibility of the neighbors receiving the LLDP frame. With fast start repeat count it is possible to specify the number of times the fast start transmission would be repeated. The recommended value is 4 times, given that 4 LLDP frames with a 1 second interval will be transmitted, when an LLDP frame with new information is received. It should be noted that LLDP-MED and the LLDP-MED Fast Start mechanism is only intended to run on links between LLDP-MED Network Connectivity Devices and Endpoint Devices, and as such does not apply to links between LAN infrastructure elements, including Network Connectivity Devices, or other types of links.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned8 1..10  

cie1000LldpConfigMedGlobalLatitude 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.2
Latitude degrees in 2s-complement as specified in RFC 3825. Positive numbers are north of the equator and negative numbers are south of the equator.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Integer64  

cie1000LldpConfigMedGlobalLongitude 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.3
Longitude degrees in 2s-complement as specified in RFC 3825. Positive values are East of the prime meridian and negative numbers are West of the prime meridian.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Integer64  

cie1000LldpConfigMedGlobalAltitudeType 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.4
Setting altitude type Possible to select between two altitude types (floors or meters). Meters are representing meters of altitude defined by the vertical datum specified. Floors are representing altitude in a form more relevant in buildings which have different floor-to-floor dimensions. An altitude = 0.0 is meaningful even outside a building, and represents ground level at the given latitude and longitude. Inside a building, 0.0 represents the floor level associated with ground level at the main entrance.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000lldpmedAltitudeType  

cie1000LldpConfigMedGlobalAltitude 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.5
Altitude value in 2s-complement as specified in RFC 3825
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cie1000LldpConfigMedGlobalElinAddr 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.6
Emergency Call Service ELIN identifier data format is defined to carry the ELIN identifier as used during emergency call setup to a traditional CAMA or ISDN trunk-based PSAP. This format consists of a numerical digit string, corresponding to the ELIN to be used for emergency calling. Maximum number of octets are 25.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000DisplayString Size(0..25)  

cie1000LldpConfigMedGlobalDatum 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.7
Setting datum to configure the datum (geodetic system) to use. The Map Datum is used for the coordinates given in these options: WGS84: (Geographical 3D) - World Geodesic System 1984, CRS Code 4327, Prime Meridian Name: Greenwich. NAD83/NAVD88: North American Datum 1983, CRS Code 4269, Prime Meridian Name: Greenwich;The associated vertical datum is the North American Vertical Datum of 1988 (NAVD88).This datum pair is to be used when referencing locations on land, not near tidal water(which would use Datum = NAD83/MLLW). NAD83/MLLW: North American Datum 1983, CRS Code 4269, Prime Meridian Name: Greenwich; The associated vertical datum is Mean Lower Low Water (MLLW). This datum pair is to be used when referencing locations on water/sea/ocean.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000lldpmedDatumType  

cie1000LldpConfigMedGlobalCountryCode 1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.8
The two-letter ISO 3166 country code in capital ASCII letters - Example: DK, DE or US.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000DisplayString Size(0..2)  

cie1000LldpConfigMedLocationInfTable 1.3.6.1.4.1.9.9.832.1.34.1.2.3.5
The civic address location information. Each civic address can contain up to 250 characters, but the total amount of characters for the combined civic address locations must not exceed 250 bytes. Note: If an civic address location is non-empty it uses the amount of characters plus addition two characters. This is described in TIA1057, Section 10.2.4.3.2.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpConfigMedLocationInfEntry

cie1000LldpConfigMedLocationInfEntry 1.3.6.1.4.1.9.9.832.1.34.1.2.3.5.1
Each civic address type as defined in TIA1057, Section 3.4 in Annex B
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpConfigMedLocationInfEntry  

cie1000LldpConfigMedLocationInfLldpmedIndex 1.3.6.1.4.1.9.9.832.1.34.1.2.3.5.1.2
Civic address type. 1 - State/National subdivisions 2 - County, parish, gun (JP), district (IN) 3 - City, township 4 - City division, borough, city district, ward, chou (JP) 5 - Neighborhood, block 6 - Street 16 - Leading street direction 17 - Trailing street direction 18 - Street suffix 19 - House number 20 - House number suffix 21 - Landmark or vanity address 22 - Additional location information 23 - Name 24 - Postal/zip code 25 - Building 26 - Unit 27 - Floor 28 - Room 29 - Place type 30 - Postal 31 - Post office 32 - Additional code
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000lldpmedCivicAddressType  

cie1000LldpConfigMedLocationInfCivicAddress 1.3.6.1.4.1.9.9.832.1.34.1.2.3.5.1.3
Civic address
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpConfigMedPolicyRowEditor 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6
OBJECT IDENTIFIER    

cie1000LldpConfigMedPolicyRowEditorLldpmedPolicy 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.1
Policy index.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..31  

cie1000LldpConfigMedPolicyRowEditorApplicationType 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.3
The LLDP policy application type.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000lldpmedRemoteNetworkPolicyApplicationType  

cie1000LldpConfigMedPolicyRowEditorTagged 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.4
The LLDP policy tagged flag. Defines if LLDP policy uses tagged VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cie1000LldpConfigMedPolicyRowEditorVlanId 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.5
The LLDP policy VLAN ID. Only valid when policy 'Tagged' is TRUE
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned16 1..4095  

cie1000LldpConfigMedPolicyRowEditorL2Priority 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.6
The LLDP policy L2 priority.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned8 0..7  

cie1000LldpConfigMedPolicyRowEditorDscp 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.7
The LLDP policy DSCP.
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000Unsigned8 0..63  

cie1000LldpConfigMedPolicyRowEditorAction 1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.100
Action
Status: current Access: read-write
OBJECT-TYPE    
  CIE1000RowEditorState  

cie1000LldpStatus 1.3.6.1.4.1.9.9.832.1.34.1.3
OBJECT IDENTIFIER    

cie1000LldpStatusStatistics 1.3.6.1.4.1.9.9.832.1.34.1.3.1
OBJECT IDENTIFIER    

cie1000LldpStatusStatisticsGlobalCounters 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1
OBJECT IDENTIFIER    

cie1000LldpStatusStatisticsGlobalCountersTableInserts 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.1
Shows the number of new entries added since switch reboot.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsGlobalCountersTableDeletes 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.2
Shows the number of new entries deleted since switch reboot.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsGlobalCountersTableDrops 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.3
Shows the number of LLDP frames dropped due to the entry table being full.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsGlobalCountersTableAgeOuts 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.4
Shows the number of entries deleted due to Time-To-Live expiring.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsGlobalCountersLastChangeTime 1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.5
Shows the time when the last entry was last deleted or added. It also shows the time elapsed since the last change was detected.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned64  

cie1000LldpStatusStatisticsTable 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2
This table represents the LLDP interface counters
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpStatusStatisticsEntry

cie1000LldpStatusStatisticsEntry 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1
Each port interface has a set of statistics counters
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpStatusStatisticsEntry  

cie1000LldpStatusStatisticsIfIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.1
Logical interface number index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000LldpStatusStatisticsTxTotal 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.2
Shows the number of LLDP frames transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsRxTotal 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.3
Shows the number of LLDP frames received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsRxError 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.4
Shows the number of received LLDP frames containing some kind of error.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsRxDiscarded 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.5
Show the number of LLDP frames discarded. If a LLDP frame is received at an interface, and the switch's internal table has run full, the LLDP frame is counted and discarded. This situation is known as 'Too Many Neighbors' in the LLDP standard. LLDP frames require a new entry in the table when the Chassis ID or Remote Port ID is not already contained within the table. Entries are removed from the table when a given interface's link is down, an LLDP shutdown frame is received, or when the entry ages out.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsTLVsDiscarded 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.6
Shows the number of TLVs discarded. Each LLDP frame can contain multiple pieces of information, known as TLVs (TLV is short for 'Type Length Value'). If a TLV is malformed, it is counted and discarded.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsTLVsUnrecognized 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.7
Shows the number of well-formed TLVs, but with an unknown type value.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsTLVsOrgDiscarded 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.8
Shows the number of well-formed TLVs, but with an organizationally TLV which is not supported.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusStatisticsAgeOuts 1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.9
Show the number of age-outs. Each frame contains information about how long time the LLDP information is valid (age-out time). If no new LLDP frame is received within the age out time, the information is removed, and the counter is incremented.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cie1000LldpStatusNeighborsInfTable 1.3.6.1.4.1.9.9.832.1.34.1.3.2
This is a table to show the LLDP neighbors information for a specific interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpStatusNeighborsInfEntry

cie1000LldpStatusNeighborsInfEntry 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1
Each interface has a set of neighbors information
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpStatusNeighborsInfEntry  

cie1000LldpStatusNeighborsInfIfIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.1
Logical interface number index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000LldpStatusNeighborsInfLldpmedIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.2
Neighbor information table entry index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..192  

cie1000LldpStatusNeighborsInfChassisId 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.4
Shows the LLDP neighbor's chassis Id.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..254)  

cie1000LldpStatusNeighborsInfPortId 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.5
Shows the LLDP neighbor's port id.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..254)  

cie1000LldpStatusNeighborsInfPortDescription 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.6
Shows the LLDP neighbor's port description.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..254)  

cie1000LldpStatusNeighborsInfSystemName 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.7
Shows the LLDP neighbor's system name.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..254)  

cie1000LldpStatusNeighborsInfSystemDescription 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.8
Shows the LLDP neighbor's system description.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..254)  

cie1000LldpStatusNeighborsInfSystemCapabilities 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.9
Shows the LLDP neighbor's system capabilities as bit mask. If the bit is set, it means that the functionality is supported by the neighbor system. Bit 0 represents Other. Bit 1 represents Repeater. Bit 2 represents Bridge. Bit 3 represents WLAN Access Point. Bit 4 represents Router. Bit 5 represents Telephone. Bit 6 represents DOCSIS cable device. Bit 7 represents Station Only. Bit 8 represents Reserved.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpStatusNeighborsInfSystemCapabilitiesEnable 1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.10
Shows the LLDP neighbor's system capabilities which is enabled. If the bit is set, it means that the functionality is currently enabled at the neighbor system. Bit 0 represents Other. Bit 1 represents Repeater. Bit 2 represents Bridge. Bit 3 represents WLAN Access Point. Bit 4 represents Router. Bit 5 represents Telephone. Bit 6 represents DOCSIS cable device. Bit 7 represents Station Only. Bit 8 represents Reserved.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpStatusNeighborsMgmtInfTable 1.3.6.1.4.1.9.9.832.1.34.1.3.3
This is a table to show the LLDP neighbors information for a specific interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpStatusNeighborsMgmtInfEntry

cie1000LldpStatusNeighborsMgmtInfEntry 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1
Each interface has a set of neighbors information
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpStatusNeighborsMgmtInfEntry  

cie1000LldpStatusNeighborsMgmtInfIfIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.1
Logical interface number index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000LldpStatusNeighborsMgmtInfLldpmedIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.2
Neighbor information table entry index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..192  

cie1000LldpStatusNeighborsMgmtInfLldpManagement 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.4
Neighbor management information table entry index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..1  

cie1000LldpStatusNeighborsMgmtInfSystemMgmAddressSubtype 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.5
LLDP neighbor's management address subtype , section 9.5.9.3 IEEE802.1AB-2005.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned8  

cie1000LldpStatusNeighborsMgmtInfSystemMgmtAddress 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.6
LLDP neighbor's management address string, section 9.5.9.4 IEEE802.1AB-2005.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..31)  

cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterfaceSubtype 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.7
Interface numbering subtype, section 9.5.9.5 IEEE802.1AB-2005.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterface 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.8
Interface number, section 9.5.9.6 IEEE802.1AB-2005.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cie1000LldpStatusNeighborsMgmtInfSystemMgmtOid 1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.9
Object identifier, section 9.5.9.8 IEEE802.1AB-2005.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

cie1000LldpStatusMed 1.3.6.1.4.1.9.9.832.1.34.1.3.4
OBJECT IDENTIFIER    

cie1000LldpStatusMedRemoteDeviceInfoTable 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1
This is a table to show the LLDP neighbors information for a specific interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpStatusMedRemoteDeviceInfoEntry

cie1000LldpStatusMedRemoteDeviceInfoEntry 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1
Each interface has a set of neighbors information
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpStatusMedRemoteDeviceInfoEntry  

cie1000LldpStatusMedRemoteDeviceInfoIfIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.1
Logical interface number index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000LldpStatusMedRemoteDeviceInfoLldpmedIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.2
Neighbor information table entry index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..192  

cie1000LldpStatusMedRemoteDeviceInfoCapabilities 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.4
LLDP neighbor's capabilities bit mask. Bit 0 represents LLDP-MED capabilities. Bit 1 represents Network Policy. Bit 2 represents Location Identification. Bit 3 represents Extended Power via MDI - PSE. Bit 4 represents Extended Power via MDI - PD Bit 5 represents Inventory
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpStatusMedRemoteDeviceInfoCapabilitiesEnabled 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.5
LLDP neighbor's capabilities bit mask for the capabilities which are currently enabled. Bit 0 represents LLDP-MED capabilities. Bit 1 represents Network Policy. Bit 2 represents Location Identification. Bit 3 represents Extended Power via MDI - PSE. Bit 4 represents Extended Power via MDI - PD Bit 5 represents Inventory
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpStatusMedRemoteDeviceInfoLatitude 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.6
Latitude degrees in 2s-complement as specified in RFC 3825. Positive numbers are north of the equator and negative numbers are south of the equator.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Integer64  

cie1000LldpStatusMedRemoteDeviceInfoLongitude 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.7
Longitude degrees in 2s-complement as specified in RFC 3825. Positive values are East of the prime meridian and negative numbers are West of the prime meridian.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Integer64  

cie1000LldpStatusMedRemoteDeviceInfoAltitudeType 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.8
Altitude type as either floors or meters. Meters are representing meters of altitude defined by the vertical datum specified. Floors are representing altitude in a form more relevant in buildings which have different floor-to-floor dimensions. An altitude = 0.0 is meaningful even outside a building, and represents ground level at the given latitude and longitude. Inside a building, 0.0 represents the floor level associated with ground level at the main entrance.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000lldpmedAltitudeType  

cie1000LldpStatusMedRemoteDeviceInfoAltitude 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.9
Altitude value in 2s-complement as specified in RFC 3825
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cie1000LldpStatusMedRemoteDeviceInfoDatum 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.10
Datum (geodetic system) . The Map Datum is used for the coordinates given in these options: WGS84: (Geographical 3D) - World Geodesic System 1984, CRS Code 4327, Prime Meridian Name: Greenwich. NAD83/NAVD88: North American Datum 1983, CRS Code 4269, Prime Meridian Name: Greenwich; The associated vertical datum is the North American Vertical Datum of 1988 (NAVD88). This datum pair is to be used when referencing locations on land, not near tidal water(which would use Datum = NAD83/MLLW). NAD83/MLLW: North American Datum 1983, CRS Code 4269, Prime Meridian Name: Greenwich; The associated vertical datum is Mean Lower Low Water (MLLW). This datum pair is to be used when referencing locations on water/sea/ocean.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000lldpmedDatumType  

cie1000LldpStatusMedRemoteDeviceInfoElinaddr 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.11
Emergency Call Service ELIN identifier data format is defined to carry the ELIN identifier as used during emergency call setup to a traditional CAMA or ISDN trunk-based PSAP. This format consists of a numerical digit string, corresponding to the ELIN to be used for emergency calling. Maximum number of octets are 25.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..25)  

cie1000LldpStatusMedRemoteDeviceInfoDeviceType 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.12
Shows the LLDP neighbor's device type.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000lldpmedRemoteDeviceType  

cie1000LldpStatusMedRemoteDeviceInfoHwRev 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.13
Shows the LLDP neighbor's hardware revision.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..31)  

cie1000LldpStatusMedRemoteDeviceInfoFwRev 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.14
Shows the LLDP neighbor's firmware revision.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..31)  

cie1000LldpStatusMedRemoteDeviceInfoSwRev 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.15
Shows the LLDP neighbor's software revision.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..31)  

cie1000LldpStatusMedRemoteDeviceInfoSerialNo 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.16
Shows the LLDP neighbor's serial number.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..31)  

cie1000LldpStatusMedRemoteDeviceInfoManufacturerName 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.17
Shows the LLDP neighbor's manufacturer name.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..31)  

cie1000LldpStatusMedRemoteDeviceInfoModelName 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.18
Shows the LLDP neighbor's model name.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..31)  

cie1000LldpStatusMedRemoteDeviceInfoAssetId 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.19
Shows the LLDP neighbor's asset id.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..31)  

cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSys 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.20
Shows the LLDP neighbor's Receive tw_sys_rx . Tw_sys_rx is defined as the time (expressed in microseconds) that the transmitting link partner will wait before it starts transmitting data after leaving the Low Power Idle (LPI) mode. Section 79.3.5.2, IEEE802.3az.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSys 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.21
Shows the LLDP neighbor's Transmit Tw_sys_tx . Tw_sys_tx is defined as the time (expressed in microseconds) that the receiving link partner is requesting the transmitting link partner to wait before starting the transmission data following the Low Power Idle (LPI) mode. Section 79.3.5.1, IEEE802.3az.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpStatusMedRemoteDeviceInfoEeeFbTwSys 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.22
Shows the LLDP neighbor's Fallback tw_sys_tx. A receiving link partner may inform the transmitter of an alternate desired Tw_sys_tx. Since a receiving link partner is likely to have discrete levels for savings, this provides the transmitter with additional information that it may use for a more efficient allocation. Section 79.3.5.3, IEEE802.3az.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSysEcho 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.23
Shows the LLDP neighbor's echo transmit Tw. The respective echo values shall be defined as the local link partners reflection (echo) of the remote link partners respective values. When a local link partner receives its echoed values from the remote link partner it can determine whether or not the remote link partner has received, registered, and processed its most recent values. Section 79.3.5.4, IEEE802.3az.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSysEcho 1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.24
Shows the LLDP neighbor's echo receive Tw. The respective echo values shall be defined as the local link partners reflection (echo) of the remote link partners respective values. When a local link partner receives its echoed values from the remote link partner it can determine whether or not the remote link partner has received, registered, and processed its most recent values. Section 79.3.5.4, IEEE802.3az.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned16  

cie1000LldpStatusMedRemoteDeviceLocInfoTable 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2
This is a table to show the LLDP-MED remote device (neighbor) civic location information for a specific interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpStatusMedRemoteDeviceLocInfoEntry

cie1000LldpStatusMedRemoteDeviceLocInfoEntry 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1
Each interface has a set of neighbors information
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpStatusMedRemoteDeviceLocInfoEntry  

cie1000LldpStatusMedRemoteDeviceLocInfoIfIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.1
Logical interface number index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000LldpStatusMedRemoteDeviceLocInfoLldpmedIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.2
Neighbor information table entry index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..192  

cie1000LldpStatusMedRemoteDeviceLocInfoState 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.5
National subdivision
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoCounty 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.6
County
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoCity 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.7
City
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoDistrict 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.8
City district
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoBlock 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.9
Block (Neighborhood)
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoStreet 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.10
Street
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoLeadingStreetDirection 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.11
Street Direction
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoTrailingStreetSuffix 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.12
Trailing Street Suffix
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoStreetSuffix 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.13
Street Suffix
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoHouseNo 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.14
House No.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoHouseNoSuffix 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.15
House No. Suffix
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoLandmark 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.16
Landmark
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalInfo 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.17
Additional Location Info
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoName 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.18
Name
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoZipCode 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.19
Zip code
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoBuilding 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.20
Building
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoApartment 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.21
Apartment/unit
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoFloor 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.22
Floor
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoRoomNumber 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.23
Room Number
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoPlaceType 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.24
Place type
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoPostalCommunityName 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.25
Postal Community Name
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoPoBox 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.26
Post Office Box
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalCode 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.27
Additional Code
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..250)  

cie1000LldpStatusMedRemoteDeviceLocInfoCountryCode 1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.28
The two-letter ISO 3166 country code in capital ASCII letters - Example: DK, DE or US.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000DisplayString Size(0..2)  

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTable 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3
This is a table to show the LLDP-MED remote device (neighbor) network policies information for a specific interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1
Each interface has a set of neighbors information
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry  

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoIfIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.1
Logical interface number index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedIndex 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.2
Neighbor information table entry index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..192  

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedPolicy 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.3
Policy index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..31  

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoApplicationType 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.5
The LLDP policy application type.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000lldpmedRemoteNetworkPolicyApplicationType  

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoUnknownPolicy 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.6
Policy indicates that an Endpoint Device wants to explicitly advertise that the policy is required by the device. Can be either Defined or Unknown Unknown: The network policy for the specified application type is currently unknown. Defined: The network policy is defined (known).
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTagged 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.7
Defines if LLDP policy uses tagged VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoVlanId 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.8
The policy VLAN ID. Only valid when policy 'Tagged' is TRUE
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned16 1..4095  

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoL2Priority 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.9
Shows the LLDP neighbor's policy L2 priority.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned8 0..7  

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoDscp 1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.10
LLDP policy DSCP.
Status: current Access: read-only
OBJECT-TYPE    
  CIE1000Unsigned8 0..63  

cie1000LldpControl 1.3.6.1.4.1.9.9.832.1.34.1.4
OBJECT IDENTIFIER    

cie1000LldpControlStatisticsClear 1.3.6.1.4.1.9.9.832.1.34.1.4.1
OBJECT IDENTIFIER    

cie1000LldpControlStatisticsClearTable 1.3.6.1.4.1.9.9.832.1.34.1.4.1.1
This is a table to clear LLDP statistics for a specific interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000LldpControlStatisticsClearEntry

cie1000LldpControlStatisticsClearEntry 1.3.6.1.4.1.9.9.832.1.34.1.4.1.1.1
Each interface has a set of statistics counters
Status: current Access: not-accessible
OBJECT-TYPE    
  CIE1000LldpControlStatisticsClearEntry  

cie1000LldpControlStatisticsClearIfIndex 1.3.6.1.4.1.9.9.832.1.34.1.4.1.1.1.1
Logical interface number index.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000LldpControlStatisticsClearStatisticsClear 1.3.6.1.4.1.9.9.832.1.34.1.4.1.1.1.2
Set to TRUE to clear the LLDP statistics of an interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cie1000LldpControlStatisticsClearGlobal 1.3.6.1.4.1.9.9.832.1.34.1.4.1.2
OBJECT IDENTIFIER    

cie1000LldpControlStatisticsClearGlobalClear 1.3.6.1.4.1.9.9.832.1.34.1.4.1.2.1
Set to TRUE to clear the LLDP global statistics.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cie1000LldpMibConformance 1.3.6.1.4.1.9.9.832.1.34.2
OBJECT IDENTIFIER    

cie1000LldpMibCompliances 1.3.6.1.4.1.9.9.832.1.34.2.1
OBJECT IDENTIFIER    

cie1000LldpMibGroups 1.3.6.1.4.1.9.9.832.1.34.2.2
OBJECT IDENTIFIER    

cie1000LldpConfigGlobalInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.1
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpConfigInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.2
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpConfigMedInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.3
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpConfigMedPolicyInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.4
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpConfigMedPolicyListInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.5
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpConfigMedGlobalInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.6
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpConfigMedLocationInfInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.7
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpConfigMedPolicyRowEditorInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.8
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpStatusStatisticsGlobalCountersInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.9
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpStatusStatisticsTableInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.10
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpStatusNeighborsInfInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.11
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpStatusNeighborsMgmtInfInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.12
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpStatusMedRemoteDeviceInfoInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.13
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpStatusMedRemoteDeviceLocInfoInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.14
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.15
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpControlStatisticsClearTableInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.16
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpControlStatisticsClearGlobalInfoGroup 1.3.6.1.4.1.9.9.832.1.34.2.2.17
A collection of objects.
Status: current Access: read-write
OBJECT-GROUP    

cie1000LldpMibCompliance 1.3.6.1.4.1.9.9.832.1.34.2.1.1
The compliance statement for the implementation.
Status: current Access: read-write
MODULE-COMPLIANCE