CISCO-ATM-CELL-LAYER-MIB

File: CISCO-ATM-CELL-LAYER-MIB.mib (64673 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
IF-MIB	CISCO-SMI

Imported symbols

MODULE-IDENTITY	Counter32	Counter64
Integer32	OBJECT-TYPE	Gauge32
Unsigned32	MODULE-COMPLIANCE	OBJECT-GROUP
TruthValue	ifIndex	ciscoMgmt

Defined Types

CaclConfigEntry
SEQUENCE
	caclNullCellHeader	OCTET STRING
	caclNullCellPayload	Unsigned32
	caclHecCosetEnable	TruthValue
	caclPayloadScramblingEnable	TruthValue
	caclTimeElapsed	INTEGER
	caclValidIntervals	INTEGER
	caclInvalidIntervals	INTEGER

CaclStatsEntry
SEQUENCE
	caclInRcvCLP0Cells	Counter32
	caclInRcvCLP1Cells	Counter32
	caclInValidOAMCells	Counter32
	caclInErrOAMCells	Counter32
	caclInGfcCells	Counter32
	caclInVpiVciErrCells	Counter32
	caclInLastUnknVpi	Integer32
	caclInLastUnknVci	Integer32
	caclInXmtCLP0Cells	Counter32
	caclInXmtCLP1Cells	Counter32
	caclInValidRMCells	Counter32
	caclInRcvIdleCells	Counter32
	caclInHecErrDiscCells	Counter32
	caclInHecErrCorrectedCells	Counter32
	caclInUpcCLP0DiscCells	Counter32
	caclInUpcTotalDiscCells	Counter32
	caclInUpcTotalNonCompCells	Counter32
	caclOutXmtCLP0Cells	Counter32
	caclOutXmtCLP1Cells	Counter32
	caclOutValidOAMCells	Counter32
	caclOutErrOAMCells	Counter32
	caclOutVpiVciErrCells	Counter32
	caclOutRcvCLP0Cells	Counter32
	caclOutRcvCLP1Cells	Counter32
	caclOutRcvValidRMCells	Counter32
	caclOutRcvIdleCells	Counter32
	caclHInRcvCLP0Cells	Counter64
	caclHInRcvCLP1Cells	Counter64
	caclHOutXmtCLP0Cells	Counter64
	caclHOutXmtCLP1Cells	Counter64
	caclHighInRcvCLP0Cells	Counter32
	caclHighInRcvCLP1Cells	Counter32
	caclHighInValidOAMCells	Counter32
	caclHighInVpiVciErrCells	Counter32
	caclHighInXmtCLP0Cells	Counter32
	caclHighInXmtCLP1Cells	Counter32
	caclHighInHecErrDiscCells	Counter32
	caclHighInHecErrCorrectedCells	Counter32
	caclHighOutXmtCLP0Cells	Counter32
	caclHighOutXmtCLP1Cells	Counter32
	caclHighOutValidOAMCells	Counter32
	caclHighOutRcvCLP0Cells	Counter32
	caclHighOutRcvCLP1Cells	Counter32

CaclIntervalStatsEntry
SEQUENCE
	caclIntervalNumber	INTEGER
	caclIntervalInRcvCLP0Cells	Gauge32
	caclIntervalInRcvCLP1Cells	Gauge32
	caclIntervalInValidOAMCells	Gauge32
	caclIntervalInErrOAMCells	Gauge32
	caclIntervalInGfcCells	Gauge32
	caclIntervalInVpiVciErrCells	Gauge32
	caclIntervalInLastUnknVpi	Integer32
	caclIntervalInLastUnknVci	Integer32
	caclIntervalInXmtCLP0Cells	Gauge32
	caclIntervalInXmtCLP1Cells	Gauge32
	caclIntervalInValidRMCells	Gauge32
	caclIntervalInRcvIdleCells	Gauge32
	caclIntervalInHecErrDiscCells	Gauge32
	caclIntervalInHecErrCorrCells	Gauge32
	caclIntervalInUpcCLP0DiscCells	Gauge32
	caclIntervalInUpcTotalDiscCells	Gauge32
	caclIntervalInUpcTotNonCmpCells	Gauge32
	caclIntervalOutXmtCLP0Cells	Gauge32
	caclIntervalOutXmtCLP1Cells	Gauge32
	caclIntervalOutValidOAMCells	Gauge32
	caclIntervalOutErrOAMCells	Gauge32
	caclIntervalOutVpiVciErrCells	Gauge32
	caclIntervalOutRcvCLP0Cells	Gauge32
	caclIntervalOutRcvCLP1Cells	Gauge32
	caclIntervalOutRcvValidRMCells	Gauge32
	caclIntervalOutRcvIdleCells	Gauge32
	caclHighIntervalInRcvCLP0Cells	Gauge32
	caclHighIntervalInRcvCLP1Cells	Gauge32
	caclHighIntervalInVpiVciErrCells	Gauge32
	caclHighIntervalInXmtCLP0Cells	Gauge32
	caclHighIntervalInXmtCLP1Cells	Gauge32
	caclHighIntervalInHecErrDiscCells	Gauge32
	caclHighIntervalInHecErrCorrCells	Gauge32
	caclHighIntervalOutXmtCLP0Cells	Gauge32
	caclHighIntervalOutXmtCLP1Cells	Gauge32
	caclHighIntervalOutVpiVciErrCells	Gauge32
	caclHighIntervalOutRcvCLP0Cells	Gauge32
	caclHighIntervalOutRcvCLP1Cells	Gauge32

CaclXStatsEntry
SEQUENCE
	caclHCInValidOAMCells	Counter64
	caclHCInVpiVciErrCells	Counter64
	caclHCInXmtCLP0Cells	Counter64
	caclHCInXmtCLP1Cells	Counter64
	caclHCInHecErrDiscCells	Counter64
	caclHCInHecErrCorrectedCells	Counter64
	caclHCOutValidOAMCells	Counter64
	caclHCOutRcvCLP0Cells	Counter64
	caclHCOutRcvCLP1Cells	Counter64

CaclXIntervalStatsEntry
SEQUENCE
	caclHCIntervalInRcvCLP0Cells	Counter64
	caclHCIntervalInRcvCLP1Cells	Counter64
	caclHCIntervalInVpiVciErrCells	Counter64
	caclHCIntervalInXmtCLP0Cells	Counter64
	caclHCIntervalInXmtCLP1Cells	Counter64
	caclHCIntervalInHecErrDiscCells	Counter64
	caclHCIntervalInHecErrCorrCells	Counter64
	caclHCIntervalOutXmtCLP0Cells	Counter64
	caclHCIntervalOutXmtCLP1Cells	Counter64
	caclHCIntervalOutVpiVciErrCells	Counter64
	caclHCIntervalOutRcvCLP0Cells	Counter64
	caclHCIntervalOutRcvCLP1Cells	Counter64

Defined Values

ciscoAtmCellLayerMIB		1.3.6.1.4.1.9.9.133
The MIB module to describe ATM cell layer objects and statistics of a physical line.
MODULE-IDENTITY

ciscoAtmCellLayerMIBObjects		1.3.6.1.4.1.9.9.133.1
OBJECT IDENTIFIER

caclConfig		1.3.6.1.4.1.9.9.133.1.1
OBJECT IDENTIFIER

caclStats		1.3.6.1.4.1.9.9.133.1.2
OBJECT IDENTIFIER

caclConfigTable		1.3.6.1.4.1.9.9.133.1.1.1
The Atm cell layer configuration table. An entry in this table is automatically created for each entry in the ifTable which has an ifType of atm(37), and which is layered on top of a SONET,DS3 or DS1 interface on the ATM switch.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CaclConfigEntry

caclConfigEntry		1.3.6.1.4.1.9.9.133.1.1.1.1
An entry in the caclConfigTable. The table is indexed by the ifIndex of the atm(37) interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	CaclConfigEntry

caclNullCellHeader		1.3.6.1.4.1.9.9.133.1.1.1.1.1
The first four bytes of the ATM header to be used for Null cells. Generally, idle cells are inserted into a cell stream as a mechanism for rate adaptation between the ATM data link layer and the physical layer. The header fields: Generic flow control,Payload type and Cell Loss Priority can be specified in the value of this object. It applies to both transmitted as well as received cells.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

caclNullCellPayload		1.3.6.1.4.1.9.9.133.1.1.1.1.2
Null cell Payload definition. The idle cell information field can be specified in this object. It applies to both transmitted as well as received cells. The default value is 0x6A.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..255

caclHecCosetEnable		1.3.6.1.4.1.9.9.133.1.1.1.1.3
If enabled, the algorithm of Coset Polynomial Addition is applied to do header error check calculations. It applies to transmitted as well as received cells.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

caclPayloadScramblingEnable		1.3.6.1.4.1.9.9.133.1.1.1.1.4
An indication of whether Payload Scrambling is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

caclTimeElapsed		1.3.6.1.4.1.9.9.133.1.1.1.1.5
The number of seconds that have elapsed since the beginning of the near end current error- measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..899

caclValidIntervals		1.3.6.1.4.1.9.9.133.1.1.1.1.6
The number of previous near end intervals for which data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..96

caclInvalidIntervals		1.3.6.1.4.1.9.9.133.1.1.1.1.7
The number of near end intervals in the range from 0 to caclValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..96

caclStatsTable		1.3.6.1.4.1.9.9.133.1.2.1
The ATM Cell layer stats table is for the cell layer over a physical line. There is an entry for each SONET, DS3 or DS1 line. The table maintains objects that apply to ATM end-systems, as well as objects that apply only to ATM switches. In all the following descriptions of objects, CLP-0 means Cell Loss Priority = 0, and CLP-1 means Cell Loss Priority = 1. ATM cells with CLP=0 have a higher priority in regard to cell loss than ATM cells with CLP=1. Therefore, during resource congestions, CLP=1 cells are dropped before any CLP=0 cell is dropped. Ingress direction means coming from network to the switch. Egress direction means going from switch to the network.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CaclStatsEntry

caclStatsEntry		1.3.6.1.4.1.9.9.133.1.2.1.1
An entry for the ATM Cell layer statistics for a physical line. These are realtime statistics which are collected per cell layer over a physical line. Entries are created automatically for each line. The table is indexed by the ifIndex value of the atm(37) interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	CaclStatsEntry

caclInRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.1
The number of cells received on the interface with CLP0 bit set.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.2
The number of cells received on the interface with CLP1 bit set.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInValidOAMCells		1.3.6.1.4.1.9.9.133.1.2.1.1.3
The number of valid Operation and Maintainance(OAM) cells received on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInErrOAMCells		1.3.6.1.4.1.9.9.133.1.2.1.1.4
The number of errored OAM cells received on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInGfcCells		1.3.6.1.4.1.9.9.133.1.2.1.1.5
The number of non-zero GFC cells received on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInVpiVciErrCells		1.3.6.1.4.1.9.9.133.1.2.1.1.6
The number of cells received from the interface with unknown Vpi/Vci values.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInLastUnknVpi		1.3.6.1.4.1.9.9.133.1.2.1.1.7
The last unknown Vpi value. This object is valid only if 'caclInVpiVciErrCells' is non-zero.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4095

caclInLastUnknVci		1.3.6.1.4.1.9.9.133.1.2.1.1.8
The last unknown Vci value. This object is valid only if 'caclInVpiVciErrCells' is non-zero.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

caclInXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.9
The number of CLP0 cells received from the interface and transmitted to the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.10
The number of CLP1 cells received from the interface and transmitted to the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInValidRMCells		1.3.6.1.4.1.9.9.133.1.2.1.1.11
The number of Valid RM cells received from the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInRcvIdleCells		1.3.6.1.4.1.9.9.133.1.2.1.1.12
The number of idle cells received from the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInHecErrDiscCells		1.3.6.1.4.1.9.9.133.1.2.1.1.13
Header Error Check (HEC) calculation is used to provide error detection and correction from the ATM cell header. This object is the number of received cells which were discarded because they had HEC errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInHecErrCorrectedCells		1.3.6.1.4.1.9.9.133.1.2.1.1.14
The number of received cells which had HEC errors that were corrected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInUpcCLP0DiscCells		1.3.6.1.4.1.9.9.133.1.2.1.1.15
In order to allocate resources fairly among different users, networks police traffic at resource access points. The traffic enforcement or policing taken at a UNI is called Usage Parameter Control (UPC). This is the counter associated with the number of CLP0 cells discarded due to policing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInUpcTotalDiscCells		1.3.6.1.4.1.9.9.133.1.2.1.1.16
The total number of cells(CLP0+1) discarded due to policing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclInUpcTotalNonCompCells		1.3.6.1.4.1.9.9.133.1.2.1.1.17
The number of non-compliant cells (cells that are not compliant to a specific traffic profile) discarded due to policing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclOutXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.18
The number of CLP0 cells transmitted to interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclOutXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.19
The number of CLP1 cells transmitted to interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclOutValidOAMCells		1.3.6.1.4.1.9.9.133.1.2.1.1.20
The number of Operartion and Maintainance(OAM) cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclOutErrOAMCells		1.3.6.1.4.1.9.9.133.1.2.1.1.21
The number of errored OAM cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclOutVpiVciErrCells		1.3.6.1.4.1.9.9.133.1.2.1.1.22
The number of cells with unknown vpi vci value in received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclOutRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.23
The number of CLP0 cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclOutRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.24
The number of CLP1 cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclOutRcvValidRMCells		1.3.6.1.4.1.9.9.133.1.2.1.1.25
The number of Valid RM cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclOutRcvIdleCells		1.3.6.1.4.1.9.9.133.1.2.1.1.26
The number of idle cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHInRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.27
The 64-bit version of caclInRcvCLP0Cells.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHInRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.28
The 64-bit version of caclnRcvCLP1Cells.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHOutXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.29
The 64-bit version of caclOutXmtCLP0Cells.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHOutXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.30
The 64-bit version of caclOutXmtCLP1Cells.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHighInRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.31
The upper 32 bit of the number of cells received on the interface with CLP0 bit set.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighInRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.32
The upper 32 bit of the number of cells received on the interface with CLP1 bit set.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighInValidOAMCells		1.3.6.1.4.1.9.9.133.1.2.1.1.33
The upper 32 bit of the number of valid Operation and Maintainance(OAM) cells received on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighInVpiVciErrCells		1.3.6.1.4.1.9.9.133.1.2.1.1.34
The upper 32 bit of the number of cells received from the interface with unknown Vpi/Vci values.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighInXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.35
The upper 32 bit of the number of CLP0 cells received from the interface and transmitted to the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighInXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.36
The upper 32 bit of the number of CLP1 cells received from the interface and transmitted to the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighInHecErrDiscCells		1.3.6.1.4.1.9.9.133.1.2.1.1.37
Header Error Check (HEC) calculation is used to provide error detection and correction from the ATM cell header. This object is the upper 32 bit of the number of received cells which were discarded because they had HEC errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighInHecErrCorrectedCells		1.3.6.1.4.1.9.9.133.1.2.1.1.38
The upper 32 bit of the number of received cells which had HEC errors that were corrected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighOutXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.39
The upper 32 bit of the number of CLP0 cells transmitted to interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighOutXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.40
The upper 32 bit of the number of CLP1 cells transmitted to interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighOutValidOAMCells		1.3.6.1.4.1.9.9.133.1.2.1.1.41
The upper 32 bit of the number of Operartion and Maintainance(OAM) cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighOutRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.42
The upper 32 bit of the number of CLP0 cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclHighOutRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.1.1.43
The upper 32 bit of the number of CLP1 cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

caclIntervalStatsTable		1.3.6.1.4.1.9.9.133.1.2.2
The ATM Cell layer interval stats table. This table contains statistics for the current (incomplete) interval and upto 96 previous (completed) 15-minute intervals.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CaclIntervalStatsEntry

caclIntervalStatsEntry		1.3.6.1.4.1.9.9.133.1.2.2.1
An entry for the ATM Cell layer interval statistics for a physical line. Entries are created automatically for each line. The table is indexed by the ifIndex and interval number. Interval number 0 is the current interval being collected.
Status: current	Access: not-accessible
OBJECT-TYPE
	CaclIntervalStatsEntry

caclIntervalNumber		1.3.6.1.4.1.9.9.133.1.2.2.1.1
A number between 0 and 96, where 1 is the most recently completed 15 minute interval and 96 is the 15 minutes interval completed 23 hours and 45 minutes prior to interval 1. 0 means the current interval being collected.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..96

caclIntervalInRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.2
The number of cells received on the interface with CLP0 bit set during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.3
The number of cells received on the interface with CLP1 bit set during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInValidOAMCells		1.3.6.1.4.1.9.9.133.1.2.2.1.4
The number of valid Operation and Maintainance(OAM) cells received on the interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInErrOAMCells		1.3.6.1.4.1.9.9.133.1.2.2.1.5
The number of errored OAM cells received on the interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInGfcCells		1.3.6.1.4.1.9.9.133.1.2.2.1.6
The number of non-zero GFC cells received on the interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInVpiVciErrCells		1.3.6.1.4.1.9.9.133.1.2.2.1.7
The number of cells received from the interface with unknown Vpi/Vci values during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInLastUnknVpi		1.3.6.1.4.1.9.9.133.1.2.2.1.8
The last unknown Vpi value during 15 minute interval. This object is valid only if the value of 'caclIntervalInVpiVciErrCells' for the same interval is non-zero.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4095

caclIntervalInLastUnknVci		1.3.6.1.4.1.9.9.133.1.2.2.1.9
The last unknown Vci value during 15 minute interval. This object is valid only if the value of 'caclIntervalInVpiVciErrCells' for the same interval is non-zero.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

caclIntervalInXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.10
The number of CLP0 cells received from the interface and transmitted to the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.11
The number of CLP1 cells received from the interface and transmitted to the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInValidRMCells		1.3.6.1.4.1.9.9.133.1.2.2.1.12
The number of Valid RM cells received from the interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInRcvIdleCells		1.3.6.1.4.1.9.9.133.1.2.2.1.13
The number of idle cells received from the interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInHecErrDiscCells		1.3.6.1.4.1.9.9.133.1.2.2.1.14
This object is the number of received cells which were discarded because they had HEC errors during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInHecErrCorrCells		1.3.6.1.4.1.9.9.133.1.2.2.1.15
The number of received cells which had HEC errors that were corrected during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInUpcCLP0DiscCells		1.3.6.1.4.1.9.9.133.1.2.2.1.16
This is the counter associated with the number of CLP0 cells discarded due to policing during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInUpcTotalDiscCells		1.3.6.1.4.1.9.9.133.1.2.2.1.17
The total number of cells(CLP0+1) discarded due to policing during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalInUpcTotNonCmpCells		1.3.6.1.4.1.9.9.133.1.2.2.1.18
The number of non-compliant cells (cells that are not compliant to a specific traffic profile) discarded due to policing during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalOutXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.19
The number of CLP0 cells transmitted to interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalOutXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.20
The number of CLP1 cells transmitted to interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalOutValidOAMCells		1.3.6.1.4.1.9.9.133.1.2.2.1.21
The number of Operartion and Maintainance(OAM) cells received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalOutErrOAMCells		1.3.6.1.4.1.9.9.133.1.2.2.1.22
The number of errored OAM cells received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalOutVpiVciErrCells		1.3.6.1.4.1.9.9.133.1.2.2.1.23
The number of cells with unknown vpi vci value in received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalOutRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.24
The number of CLP0 cells received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalOutRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.25
The number of CLP1 cells received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalOutRcvValidRMCells		1.3.6.1.4.1.9.9.133.1.2.2.1.26
The number of Valid RM cells received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclIntervalOutRcvIdleCells		1.3.6.1.4.1.9.9.133.1.2.2.1.27
The number of idle cells received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalInRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.28
The Upper 32 bit of the number of cells received on the interface with CLP0 bit set during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalInRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.29
The Upper 32 bit of the number of cells received on the interface with CLP1 bit set during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalInVpiVciErrCells		1.3.6.1.4.1.9.9.133.1.2.2.1.30
The Upper 32 bit of the number of cells received from the interface with unknown Vpi/Vci values during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalInXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.31
The Upper 32 bit of the number of CLP0 cells received from the interface and transmitted to the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalInXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.32
The Upper 32 bit of the number of CLP1 cells received from the interface and transmitted to the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalInHecErrDiscCells		1.3.6.1.4.1.9.9.133.1.2.2.1.33
This object is the Upper 32 bit of the number of received cells which were discarded because they had HEC errors during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalInHecErrCorrCells		1.3.6.1.4.1.9.9.133.1.2.2.1.34
The number of received cells which had HEC errors that were corrected during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalOutXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.35
The number of CLP0 cells transmitted to interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalOutXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.36
The number of CLP1 cells transmitted to interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalOutVpiVciErrCells		1.3.6.1.4.1.9.9.133.1.2.2.1.37
The number of cells with unknown vpi vci value in received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalOutRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.38
The number of CLP0 cells received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclHighIntervalOutRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.2.1.39
The number of CLP1 cells received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

caclXStatsTable		1.3.6.1.4.1.9.9.133.1.2.3
The ATM Cell layer stats table is for the cell layer over a physical line. There is an entry for each SONET, DS3 or DS1 line. The table maintains objects that apply to ATM end-systems, as well as objects that apply only to ATM switches. In all the following descriptions of objects, CLP-0 means Cell Loss Priority = 0, and CLP-1 means Cell Loss Priority = 1. ATM cells with CLP=0 have a higher priority in regard to cell loss than ATM cells with CLP=1. Therefore, during resource congestions, CLP=1 cells are dropped before any CLP=0 cell is dropped. Ingress direction means coming from network to the switch. Egress direction means going from switch to the network.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CaclXStatsEntry

caclXStatsEntry		1.3.6.1.4.1.9.9.133.1.2.3.1
An entry for the ATM Cell layer statistics for a physical line. These are realtime statistics which are collected per cell layer over a physical line. Entries are created automatically for each line. The table is indexed by the ifIndex value of the atm(37) interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	CaclXStatsEntry

caclHCInValidOAMCells		1.3.6.1.4.1.9.9.133.1.2.3.1.1
The 64 bit version of the number of valid Operation and Maintainance(OAM) cells received on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCInVpiVciErrCells		1.3.6.1.4.1.9.9.133.1.2.3.1.2
The 64 bit version of the number of cells received from the interface with unknown Vpi/Vci values.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCInXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.3.1.3
The 64 bit version of the number of CLP0 cells received from the interface and transmitted to the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCInXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.3.1.4
The 64 bit version of the number of CLP1 cells received from the interface and transmitted to the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCInHecErrDiscCells		1.3.6.1.4.1.9.9.133.1.2.3.1.5
Header Error Check (HEC) calculation is used to provide error detection and correction from the ATM cell header. This object is 64 bit version of the the number of received cells which were discarded because they had HEC errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCInHecErrCorrectedCells		1.3.6.1.4.1.9.9.133.1.2.3.1.6
The 64 bit version of thenumber of received cells which had HEC errors that were corrected.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCOutValidOAMCells		1.3.6.1.4.1.9.9.133.1.2.3.1.7
The 64 bit version of the number of Operartion and Maintainance(OAM) cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCOutRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.3.1.8
The 64 bit version of the number of CLP0 cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCOutRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.3.1.9
The 64 bit version of the number of CLP1 cells received by the interface from the switch fabric.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclXIntervalStatsTable		1.3.6.1.4.1.9.9.133.1.2.4
The ATM Cell layer interval stats table. This table contains statistics for the current (incomplete) interval and upto 96 previous (completed) 15-minute intervals.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CaclXIntervalStatsEntry

caclXIntervalStatsEntry		1.3.6.1.4.1.9.9.133.1.2.4.1
An entry for the ATM Cell layer interval statistics for a physical line. Entries are created automatically for each line. The table is indexed by the ifIndex and interval number. Interval number 0 is the current interval being collected.
Status: current	Access: not-accessible
OBJECT-TYPE
	CaclXIntervalStatsEntry

caclHCIntervalInRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.4.1.1
The 64 bit version of the number of cells received on the interface with CLP0 bit set during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalInRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.4.1.2
The 64 bit version of the number of cells received on the interface with CLP1 bit set during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalInVpiVciErrCells		1.3.6.1.4.1.9.9.133.1.2.4.1.3
The 64 bit version of the number of cells received from the interface with unknown Vpi/Vci values during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalInXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.4.1.4
The 64 bit version of the number of CLP0 cells received from the interface and transmitted to the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalInXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.4.1.5
The 64 bit version of the number of CLP1 cells received from the interface and transmitted to the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalInHecErrDiscCells		1.3.6.1.4.1.9.9.133.1.2.4.1.6
This object is the 64 bit version of the number of received cells which were discarded because they had HEC errors during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalInHecErrCorrCells		1.3.6.1.4.1.9.9.133.1.2.4.1.7
The 64 bit version of the number of received cells which had HEC errors that were corrected during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalOutXmtCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.4.1.8
The 64 bit version of the number of CLP0 cells transmitted to interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalOutXmtCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.4.1.9
The 64 bit version of the number of CLP1 cells transmitted to interface during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalOutVpiVciErrCells		1.3.6.1.4.1.9.9.133.1.2.4.1.10
The 64 bit version of the number of cells with unknown vpi vci value in received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalOutRcvCLP0Cells		1.3.6.1.4.1.9.9.133.1.2.4.1.11
The 64 bit version of the number of CLP0 cells received by the interfacefrom the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclHCIntervalOutRcvCLP1Cells		1.3.6.1.4.1.9.9.133.1.2.4.1.12
The 64 bit version of the number of CLP1 cells received by the interface from the switch fabric during 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

caclMIBConformance		1.3.6.1.4.1.9.9.133.1.3
OBJECT IDENTIFIER

caclMIBCompliances		1.3.6.1.4.1.9.9.133.1.3.1
OBJECT IDENTIFIER

caclMIBGroups		1.3.6.1.4.1.9.9.133.1.3.2
OBJECT IDENTIFIER

caclMIBCompliance		1.3.6.1.4.1.9.9.133.1.3.1.1
The Compliance statement for the Cisco ATM Cell layer MIB.
Status: deprecated	Access: read-only
MODULE-COMPLIANCE

caclMIBCompliance1		1.3.6.1.4.1.9.9.133.1.3.1.2
The Compliance statement for the Cisco ATM Cell layer MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

caclMIBGroup		1.3.6.1.4.1.9.9.133.1.3.2.1
A collection of objects which provide ATM cell layer configuration parmeters.
Status: current	Access: read-only
OBJECT-GROUP

caclATMSwitchStatsMIBGroup		1.3.6.1.4.1.9.9.133.1.3.2.2
A collection of objects which provide statistics for ATM switch interfaces.
Status: deprecated	Access: read-only
OBJECT-GROUP

caclATMEndSyatemStatsMIBGroup		1.3.6.1.4.1.9.9.133.1.3.2.3
A collection of objects which provide statistics for ATM end-system interfaces.
Status: deprecated	Access: read-only
OBJECT-GROUP

caclHighSpeedATMMIBGroup		1.3.6.1.4.1.9.9.133.1.3.2.4
These statistics apply to ATM interfaces with speed of OC12 or higher.
Status: deprecated	Access: read-only
OBJECT-GROUP

caclIntervalStatsMIBGroup		1.3.6.1.4.1.9.9.133.1.3.2.5
A collection of interval statistics.
Status: deprecated	Access: read-only
OBJECT-GROUP

caclATMSwitchStatsMIBGroup1		1.3.6.1.4.1.9.9.133.1.3.2.6
A collection of objects which provide statistics for ATM switch interfaces.
Status: current	Access: read-only
OBJECT-GROUP

caclATMStatsMIBGroup		1.3.6.1.4.1.9.9.133.1.3.2.7
A collection of objects which provide statistics for ATM switch and ATM end-system interfaces.
Status: current	Access: read-only
OBJECT-GROUP

caclHighSpeedATMMIBGroup1		1.3.6.1.4.1.9.9.133.1.3.2.8
These statistics apply to ATM interfaces with speed of OC12 or higher.
Status: current	Access: read-only
OBJECT-GROUP

caclIntervalStatsMIBGroup1		1.3.6.1.4.1.9.9.133.1.3.2.9
A collection of interval statistics.
Status: current	Access: read-only
OBJECT-GROUP

caclHCIntervalStatsMIBGroup		1.3.6.1.4.1.9.9.133.1.3.2.10
A collection of interval statistics.
Status: current	Access: read-only
OBJECT-GROUP