CISCO-ATM-IF-PHYS-MIB

File: CISCO-ATM-IF-PHYS-MIB.mib (23294 bytes)

Imported modules

SNMPv2-SMI	RFC1213-MIB	CISCO-SMI
SNMPv2-CONF

Imported symbols

MODULE-IDENTITY	Counter32	OBJECT-TYPE
ifIndex	ciscoMgmt	MODULE-COMPLIANCE
OBJECT-GROUP

Defined Types

CiscoAtmIfPhysEntry
SEQUENCE
	ciscoAtmIfPhysStatus	INTEGER
	ciscoAtmIfPhysSectionParityErrors	Counter32
	ciscoAtmIfPhysLineParityErrors	Counter32
	ciscoAtmIfPhysPathParityErrors	Counter32
	ciscoAtmIfPhysLcvErrors	Counter32
	ciscoAtmIfPhysCBitParityErrors	Counter32
	ciscoAtmIfPhysPBitParityErrors	Counter32
	ciscoAtmIfPhysPlcpBipViolations	Counter32
	ciscoAtmIfPhysLineFebeErrors	Counter32
	ciscoAtmIfPhysPathFebeErrors	Counter32
	ciscoAtmIfPhysCellPayloadScrambling	INTEGER
	ciscoAtmIfPhysStsStreamScrambling	INTEGER
	ciscoAtmIfPhysFramingMode	INTEGER
	ciscoAtmIfPhysLoopbackConfig	INTEGER
	ciscoAtmIfPhysLineBuildOut	INTEGER
	ciscoAtmIfPhysTransmitClockSource	INTEGER
	ciscoAtmIfPhysClockSourcePriority	INTEGER
	ciscoAtmIfPhysClockSourceStatus	INTEGER
	ciscoAtmIfPhysDS1BitErrors	Counter32
	ciscoAtmIfPhysE1CrcErrors	Counter32
	ciscoAtmIfPhysLineCode	INTEGER

Defined Values

ciscoAtmIfPhysMIB		1.3.6.1.4.1.9.9.45
A minimal set of managed objects for tracking the status of DS3/E3/DS1/E1 and SONET interfaces.
MODULE-IDENTITY

ciscoAtmIfPhysMIBObjects		1.3.6.1.4.1.9.9.45.1
OBJECT IDENTIFIER

ciscoAtmIfPhysTable		1.3.6.1.4.1.9.9.45.1.1
A table containing basic status and statistics for the physical layer of ATM interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CiscoAtmIfPhysEntry

ciscoAtmIfPhysEntry		1.3.6.1.4.1.9.9.45.1.1.1
Basic status and statistics for the physical layer of an ATM interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	CiscoAtmIfPhysEntry

ciscoAtmIfPhysStatus		1.3.6.1.4.1.9.9.45.1.1.1.1
The status of the physical interface. The value of this object is only valid when the interface's ifAdminStatus has the value 'up'. Note that some of the enumerated values are specific to a particular physical layer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), los(2), lof(3), loc(4), ais(5), yellowLine(6), yellowPath(7), lop(8), idle(9), yellowAlarm(10), plcpLOF(11), plcpYellow(12), maFERF(13), pathAis(14), ocd(15)

ciscoAtmIfPhysSectionParityErrors		1.3.6.1.4.1.9.9.45.1.1.1.2
The number of B1 (BIP) errors on the physical interface. This object is only present for SONET interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysLineParityErrors		1.3.6.1.4.1.9.9.45.1.1.1.3
The number of B2 (BIP) errors on the physical interface. This object is only present for SONET interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysPathParityErrors		1.3.6.1.4.1.9.9.45.1.1.1.4
The number of B3 (BIP) errors on the physical interface. This object is only present for SONET interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysLcvErrors		1.3.6.1.4.1.9.9.45.1.1.1.5
The number of Line Code Violation errors on the physical interface. This object is only present for DS3/E3/DS1/E1 interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysCBitParityErrors		1.3.6.1.4.1.9.9.45.1.1.1.6
The number of C-bit parity violations on the physical interface. This object is only present for DS3 interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysPBitParityErrors		1.3.6.1.4.1.9.9.45.1.1.1.7
The number of P-bit parity violations or E3 G.832 BIP-8 errors on the physical interface. This object is present only for DS3/E3 interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysPlcpBipViolations		1.3.6.1.4.1.9.9.45.1.1.1.8
The number of PLCP BIP violations on the physical interface. This object is only present for DS3/E3/DS1/E1 interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysLineFebeErrors		1.3.6.1.4.1.9.9.45.1.1.1.9
The number of Z2 (Line FEBE) errors on the physical interface. This object is only present for SONET interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysPathFebeErrors		1.3.6.1.4.1.9.9.45.1.1.1.10
The number of G1 (Path FEBE) errors on the physical interface. This object is only present for SONET interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysCellPayloadScrambling		1.3.6.1.4.1.9.9.45.1.1.1.11
The status of whether cell payload scrambling is enabled or disabled on the physical interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2)

ciscoAtmIfPhysStsStreamScrambling		1.3.6.1.4.1.9.9.45.1.1.1.12
The status of whether STS-stream scrambling is enabled or disabled on the physical interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2)

ciscoAtmIfPhysFramingMode		1.3.6.1.4.1.9.9.45.1.1.1.13
The framing format present on the physical interface. 'sonet' indicates sts-3c or sts-12c format and applies only to OC-3 and OC-12 type interfaces, respectively. 'sdh' indicates stm1 or stm4 format and applies only to OC-3 and OC-12 type interfaces, respectively. 'ds3m23adm' indicates M23 ADM mode and applies only to DS3 type interfaces. 'ds3m23plcp' indicates M23 PLCP mode and applies only to DS3 type interfaces. 'ds3cbitadm' indicates C-BIT ADM mode and applies only to DS3 type interfaces. 'ds3cbitplcp' indicates C-BIT PLCP mode and applies only to DS3 type interfaces. 'e3g832adm' indicates G.832 ADM mode and applies only to E3 type interfaces. 'e3g751adm' indicates G.751 ADM mode and applies only to E3 type interfaces. 'e3g751plcp' indicates G.751 PLCP mode and applies only to E3 type interfaces. 'ds1sfadm' indicates DS1 SF ADM mode and applies only to DS1 type interfaces. 'ds1esfadm' indicates DS1 ESF ADM mode and applies only to DS1 type interfaces. 'ds1sfplcp' indicates DS1 SF PLCP mode and applies only to DS1 type interfaces. 'ds1esfplcp' indicates DS1 ESF PLCP mode and applies only to DS1 type interfaces. 'e1adm' indicates E1 ADM mode and applies only to E1 type interfaces. 'e1plcp' indicates E1 PLCP mode and applies only to E1 type interfaces. 'e1crcadm' indicates E1 CRC-4 ADM mode and applies only to E1 type interfaces. 'e1crcplcp' indicates E1 CRC-4 PLCP mode and applies only to E1 type interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sonet(1), sdh(2), ds3m23adm(3), ds3m23plcp(4), ds3cbitadm(5), ds3cbitplcp(6), e3g832adm(7), e3g751adm(8), e3g751plcp(9), ds1sfadm(10), ds1esfadm(11), ds1sfplcp(12), ds1esfplcp(13), e1adm(14), e1plcp(15), e1crcadm(16), e1crcplcp(17)

ciscoAtmIfPhysLoopbackConfig		1.3.6.1.4.1.9.9.45.1.1.1.14
The loopback configured on the physical interface: 'noLoop' indicates no loopback is present. 'diagnosticLoop' indicates transmit data stream is looped to the receive direction. 'lineLoop' indicates receive data stream is looped to the transmit direction. 'otherLoop' indicates loopbacks that are not defined here.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noLoop(1), diagnosticLoop(2), lineLoop(3), otherLoop(4)

ciscoAtmIfPhysLineBuildOut		1.3.6.1.4.1.9.9.45.1.1.1.15
The line buildout configured on the transmit signal: 'e3AllCables' applies to all cables of E3 physical interfaces. 'ds3CablesUnder225' applies to cables under 225 feet of DS3 physical interfaces. 'ds3CablesOver225' applies to cables over 225 feet of DS3 physical interfaces. 'ds1Cables0To110' applies to cables 0 to 110 feet of DS1 physical interfaces. 'ds1Cables110To220' applies to cables 110 to 220 feet of DS1 physical interfaces. 'ds1Cables220To330' applies to cables 220 to 330 feet of DS1 physical interfaces. 'ds1Cables330To440' applies to cables 330 to 440 feet of DS1 physical interfaces. 'ds1Cables440To550' applies to cables 440 to 550 feet of DS1 physical interfaces. 'ds1Cables550To660' applies to cables 550 to 660 feet of DS1 physical interfaces. 'ds1CablesOver600' applies to cables over 600 feet of DS1 physical interfaces. 'e1AllCables' applies to all cables of E1 physical interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	e3AllCables(1), ds3CablesUnder225(2), ds3CablesOver225(3), ds1Cables0To110(4), ds1Cables110To220(5), ds1Cables220To330(6), ds1Cables330To440(7), ds1Cables440To550(8), ds1Cables550To660(9), ds1CablesOver600(10), e1AllCables(11)

ciscoAtmIfPhysTransmitClockSource		1.3.6.1.4.1.9.9.45.1.1.1.16
The source of the tranmit clock: 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'freeRunning' indicates that a local clock source is used. 'networkDerived' indicates that recovered receive clock from another interface is used as the transmit clock source.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTiming(1), freeRunning(2), networkDerived(3)

ciscoAtmIfPhysClockSourcePriority		1.3.6.1.4.1.9.9.45.1.1.1.17
The priority of this interface if configured as a network clock source. 'notConfigured' indicates this is not configured as a network clock source.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notConfigured(1), priority1(2), priority2(3), priority3(4), priority4(5)

ciscoAtmIfPhysClockSourceStatus		1.3.6.1.4.1.9.9.45.1.1.1.18
The network clock source status of this interface: 'notSelected' indicates this is not selected as the network clock source. 'selected' indicates this is selected as the network clock source.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSelected(1), selected(2)

ciscoAtmIfPhysDS1BitErrors		1.3.6.1.4.1.9.9.45.1.1.1.19
The number of bit errors (CRC-6 error in ESF mode and framing bit error in SF mode) on the physical interface. This object is only present for DS1 interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysE1CrcErrors		1.3.6.1.4.1.9.9.45.1.1.1.20
The number of CRC errors (in CRC-4 mode) on the physical interface. This object is only present for E1 interfaces.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmIfPhysLineCode		1.3.6.1.4.1.9.9.45.1.1.1.21
The line coding present on the physical interface This object is only present for DS1/E1 interfaces. 'ami' indicates alternate mark inversion (AMI) line code on the DS1/E1 interface. 'b8zs' indicates B8ZS line code on the physical interface and applies only to DS1 interfaces. 'hdb3' indicates HDB3 line code on the physical interface and applies only to E1 interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ami(1), b8zs(2), hdb3(3)

ciscoAtmIfPhysMIBConformance		1.3.6.1.4.1.9.9.45.3
OBJECT IDENTIFIER

ciscoAtmIfPhysMIBCompliances		1.3.6.1.4.1.9.9.45.3.1
OBJECT IDENTIFIER

ciscoAtmIfPhysMIBGroups		1.3.6.1.4.1.9.9.45.3.2
OBJECT IDENTIFIER

ciscoAtmIfPhysMIBCompliance		1.3.6.1.4.1.9.9.45.3.1.1
The compliance statement for entities which implement the Cisco ATM Interface Physical MIB.
Status: obsolete	Access: read-write
MODULE-COMPLIANCE

ciscoAtmIfPhysMIBCompliance2		1.3.6.1.4.1.9.9.45.3.1.2
The compliance statement for entities which implement the Cisco ATM Interface Physical MIB.
Status: obsolete	Access: read-write
MODULE-COMPLIANCE

ciscoAtmIfPhysMIBCompliance3		1.3.6.1.4.1.9.9.45.3.1.3
The compliance statement for entities which implement the Cisco ATM Interface Physical MIB.
Status: current	Access: read-write
MODULE-COMPLIANCE

ciscoAtmIfPhysMIBCommonGroup		1.3.6.1.4.1.9.9.45.3.2.1
A collection of objects common to all ATM physical layer interfaces.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmIfPhysMIBSonetGroup		1.3.6.1.4.1.9.9.45.3.2.2
A collection of objects for ATM SONET interfaces.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmIfPhysMIBDs3E3Group		1.3.6.1.4.1.9.9.45.3.2.3
A collection of objects for ATM DS3/E3 interfaces.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmIfPhysMIBCommonGroup2		1.3.6.1.4.1.9.9.45.3.2.4
Additional collection of objects common to all ATM physical layer interfaces.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmIfPhysMIBSonetGroup2		1.3.6.1.4.1.9.9.45.3.2.5
Additional collection of objects for ATM SONET interfaces.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmIfPhysMIBDs3Group		1.3.6.1.4.1.9.9.45.3.2.6
Collection of objects for ATM DS3 interfaces.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmIfPhysMIBDs1E1Group		1.3.6.1.4.1.9.9.45.3.2.7
A collection of objects for ATM DS1/E1 interfaces.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmIfPhysMIBDs1Group		1.3.6.1.4.1.9.9.45.3.2.8
A collection of objects for ATM DS1 interfaces.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmIfPhysMIBE1Group		1.3.6.1.4.1.9.9.45.3.2.9
A collection of objects for ATM E1 interfaces.
Status: current	Access: read-write
OBJECT-GROUP