CISCO-ATM-SWITCH-FR-IWF-MIB

File: CISCO-ATM-SWITCH-FR-IWF-MIB.mib (57638 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
CISCO-SMI	CISCO-TC	ATM-MIB
IF-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Integer32
Counter32	TEXTUAL-CONVENTION	RowStatus
TimeStamp	TruthValue	MODULE-COMPLIANCE
OBJECT-GROUP	ciscoMgmt	Unsigned32
AtmTrafficDescrParamIndex	ifIndex	InterfaceIndex

Defined Types

CasfTrafficDescrRow
Identifies an index into the casfTrafficDescrTable. The value 0 signifies that no row has been identified.
TEXTUAL-CONVENTION
	Unsigned32	1..2147483647

DlciValue
A numerical value identifying a Data Link Connection Identifier (DLCI) for a Frame Relay connection. The valid range of values depends on the format of the address field used, as described in ITU Recommendation Q.922. When a 2-octet address field is used, the value ranges from 0 to 1023.
TEXTUAL-CONVENTION
	Integer32	0..4194303

ConnectionKind
The kind of connection, distinguished by the use of call control.
TEXTUAL-CONVENTION
	INTEGER	pvc(1), svcIncoming(2), svcOutgoing(3), spvcInitiator(4), spvcTarget(5)

AtmAddr
An ATM address. The semantics are implied by the length. The address types are: - no address (0 octets) - E.164 (8 octets) - NSAP (20 octets) In addition, when subaddresses are used the AtmAddr may represent the concatenation of address and subaddress. The associated address types are: - E.164, E.164 (16 octets) - E.164, NSAP (28 octets) - NSAP, NSAP (40 octets) Address lengths other than defined in this definition imply address types defined elsewhere. Note: The E.164 address is encoded in BCD format.
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..40)

CasfTrafficDescrEntry
SEQUENCE
	casfTrafficDescrIndex	CasfTrafficDescrRow
	casfTrafficDescrCIR	Unsigned32
	casfTrafficDescrBc	Unsigned32
	casfTrafficDescrBe	Unsigned32
	casfTrafficDescrPIR	Unsigned32
	casfTrafficDescrServCategory	INTEGER
	casfTrafficDescrAtmIndex	AtmTrafficDescrParamIndex
	casfTrafficDescrRowStatus	RowStatus

CasfVcEndptEntry
SEQUENCE
	casfVcEndptDlci	DlciValue
	casfVcEndptRxTrafficDescrRow	CasfTrafficDescrRow
	casfVcEndptTxTrafficDescrRow	CasfTrafficDescrRow
	casfVcEndptRxNegTrafficDescrRow	CasfTrafficDescrRow
	casfVcEndptTxNegTrafficDescrRow	CasfTrafficDescrRow
	casfVcEndptConnKind	ConnectionKind
	casfVcEndptIwfType	INTEGER
	casfVcEndptClpMode	INTEGER
	casfVcEndptDeMode	INTEGER
	casfVcEndptEfciMode	INTEGER
	casfVcEndptUpcMode	INTEGER
	casfVcEndptSpvcRemoteAddr	AtmAddr
	casfVcEndptSpvcRemoteType	INTEGER
	casfVcEndptSpvcRemoteDlci	DlciValue
	casfVcEndptSpvcRemoteVpi	INTEGER
	casfVcEndptSpvcRemoteVci	INTEGER
	casfVcEndptCreationTime	TimeStamp
	casfVcEndptRcvdSigStatus	INTEGER
	casfVcEndptRowStatus	RowStatus
	casfVcSignalStandardCalledIe	TruthValue

CasfFrLmiEntry
SEQUENCE
	casfFrLmiProtocol	INTEGER
	casfFrLmiType	INTEGER
	casfFrLmiUserN391	INTEGER
	casfFrLmiUserN392	INTEGER
	casfFrLmiUserN393	INTEGER
	casfFrLmiUserT391	INTEGER
	casfFrLmiNetN392	INTEGER
	casfFrLmiNetN393	INTEGER
	casfFrLmiNetT392	INTEGER
	casfFrLmiEnquiryIns	Counter32
	casfFrLmiEnquiryOuts	Counter32
	casfFrLmiStatusIns	Counter32
	casfFrLmiStatusOuts	Counter32
	casfFrLmiStatusTimeouts	Counter32
	casfFrLmiStatusEnqTimeouts	Counter32

CasfConfIfEntry
SEQUENCE
	casfConfIfAtmAddress	AtmAddr
	casfConfIfUpcIntent	INTEGER
	casfConfIfBcDefault	Integer32
	casfConfIfCledSpvcDeModeDef	INTEGER
	casfConfIfCledSpvcClpModeDef	INTEGER

CasfVcCountEntry
SEQUENCE
	casfVcCountReceivedFrames	Counter32
	casfVcCountReceivedOctets	Counter32
	casfVcCountReceivedFECNs	Counter32
	casfVcCountReceivedBECNs	Counter32
	casfVcCountReceivedDEs	Counter32
	casfVcCountInDiscards	Counter32
	casfVcCountOutDiscards	Counter32
	casfVcCountSentFrames	Counter32
	casfVcCountSentOctets	Counter32
	casfVcCountSentFECNs	Counter32
	casfVcCountSentBECNs	Counter32
	casfVcCountSentDEs	Counter32
	casfVcCountTaggedFECNs	Counter32
	casfVcCountTaggedBECNs	Counter32
	casfVcCountTaggedDEs	Counter32

CasfVcIwfCountEntry
SEQUENCE
	casfVcIwfCountInUnknownProts	Counter32
	casfVcIwfCountOutUnknownProts	Counter32
	casfVcIwfCountReassemblyTimeouts	Counter32
	casfVcIwfCountLengthErrors	Counter32
	casfVcIwfCountCrcErrors	Counter32
	casfVcIwfCountTotalDiscardFrames	Counter32

CasfFAMapEntry
SEQUENCE
	casfFAMapDlci	DlciValue
	casfFAMapInternalAtmInterface	InterfaceIndex
	casfFAMapInternalAtmVpi	INTEGER
	casfFAMapInternalAtmVci	INTEGER

CasfAFMapEntry
SEQUENCE
	casfAFMapAtmVpi	INTEGER
	casfAFMapAtmVci	INTEGER
	casfAFMapFrIndex	InterfaceIndex
	casfAFMapFrDlci	DlciValue

Defined Values

ciscoAtmSwitchFrIwfMIB		1.3.6.1.4.1.9.9.112
A MIB module for managing Frame Relay to ATM interworking connections, and Frame Relay to Frame Relay switched connections via an ATM switching fabric, on a Cisco ATM switch.
MODULE-IDENTITY

ciscoAtmSwitchFrIwfMIBObjects		1.3.6.1.4.1.9.9.112.1
OBJECT IDENTIFIER

casfFrTraffic		1.3.6.1.4.1.9.9.112.1.1
OBJECT IDENTIFIER

casfFrVC		1.3.6.1.4.1.9.9.112.1.2
OBJECT IDENTIFIER

casfFrInterface		1.3.6.1.4.1.9.9.112.1.3
OBJECT IDENTIFIER

casfFrCounts		1.3.6.1.4.1.9.9.112.1.4
OBJECT IDENTIFIER

casfMapping		1.3.6.1.4.1.9.9.112.1.5
OBJECT IDENTIFIER

casfTrafficDescrTable		1.3.6.1.4.1.9.9.112.1.1.1
This table contains a set of self-consistent Frame Relay traffic parameters. It is intended to be used to create Frame Relay to ATM interworking connections, hence a ATM traffic service category is also included. An entry in this table is associated with an equivalent entry in the ATM traffic descriptor table (atmTrafficDescrParamTable); the mapping is given by the object casfTrafficDescrAtmIndex. The agent will not permit deletion of the associated atmTrafficDescrEntry while the Frame Relay Traffic Descriptor entry exists. When creating an entry in this table, if the value of casfTrafficDescrAtmIndex is specified, the following cases are possible: (a) if no corresponding row exists in atmTrafficDescrParamTable, the agent will create such a row with the given index value. (b) if a corresponding row does exist in atmTrafficDescrParamTable, the agent compares the parameter values in casfTrafficDescrEntry and the corresponding atmTrafficDescrParamEntry. If the two entries are not equivalent, an error is returned, and row creation fails. When creating an entry in this table, if the value of casfTrafficDescrAtmIndex is not specified, the agent will assign a value to this object so that it refers to an equivalent entry in the atmTrafficDescrParamTable. If such an equivalent entry does not already exist, the agent will create one. The agent creates rows in this table for use with signaled connections. These are called 'transient' rows - they disappear when the connection is torn down, and are not saved in non-volatile memory. By convention, transient rows usually use high-numbered index values. Entries can be deleted by setting the row status to destroy(6). The agent denies the request if the row is in use by existing connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CasfTrafficDescrEntry

casfTrafficDescrEntry		1.3.6.1.4.1.9.9.112.1.1.1.1
Describes a traffic descriptor that is used by Frame Relay connections.
Status: current	Access: not-accessible
OBJECT-TYPE
	CasfTrafficDescrEntry

casfTrafficDescrIndex		1.3.6.1.4.1.9.9.112.1.1.1.1.1
Uniquely identifies a row in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	CasfTrafficDescrRow

casfTrafficDescrCIR		1.3.6.1.4.1.9.9.112.1.1.1.1.2
The value of the Committed Information Rate (CIR) parameter.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

casfTrafficDescrBc		1.3.6.1.4.1.9.9.112.1.1.1.1.3
The value of the Committed Burst Size (Bc) parameter.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

casfTrafficDescrBe		1.3.6.1.4.1.9.9.112.1.1.1.1.4
The value of the Excess Burst Size (Be) parameter.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

casfTrafficDescrPIR		1.3.6.1.4.1.9.9.112.1.1.1.1.5
The value of the Peak Information Rate (PIR) parameter.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

casfTrafficDescrServCategory		1.3.6.1.4.1.9.9.112.1.1.1.1.6
The service category, as defined for ATM.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	vbrNrt(1), abr(2), ubr(3), vbrRt(4)

casfTrafficDescrAtmIndex		1.3.6.1.4.1.9.9.112.1.1.1.1.7
The index of the equivalent entry in the atmTrafficDescrParamTable.
Status: current	Access: read-create
OBJECT-TYPE
	AtmTrafficDescrParamIndex

casfTrafficDescrRowStatus		1.3.6.1.4.1.9.9.112.1.1.1.1.8
Used to create, delete and modify this row. None of the columnar values (other than this one) can be modified while the row is active.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

casfVcEndptTable		1.3.6.1.4.1.9.9.112.1.2.1
This table contains information about Frame Relay end-points of FR-ATM interworking connections on the switch. When an entry is created in this table, the agent creates a corresponding entry in the atmVclTable of ATM-MIB, to represent the configuration on the internal ATM port. The mapping between an entry in this table, and the corresponding entry in the atmVclTable is shown in the casfFAMapTable and the casfAFMapTable. Entries can be created or deleted in this table by an NMS using the casfVcEndptRowStatus object. To create a PVC connection end-point, the value of casfVcEndptConnKind must be 'pvc'. To create a soft VC initiator end-point, set the value of casfVcEndptConnKind to 'spvcInitiator', and specify the value of casfVcEndptSpvcRemoteAddr and casfVcEndptSpvcRemoteType. If the value of casfVcEndptSpvcRemoteType is 'frameRelay', you must also specify the value of casfVcEndptSpvcRemoteDlci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote frame relay interface. If the value of casfVcEndptSpvcRemoteType is 'atm', you must specify the values of casfVcEndptSpvcRemoteVpi and casfVcEndptSpvcRemoteVci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote ATM interface. The agent creates an entry in this table when an incoming signaling request causes a soft VC connection to be established with a local frame relay interface as the destination. The value of casfVcEndptConnKind in this case will be 'spvcTarget'. Such entries cannot be modified or deleted by network management. They will be deleted when the connection is removed by signaling.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CasfVcEndptEntry

casfVcEndptEntry		1.3.6.1.4.1.9.9.112.1.2.1.1
Models a bidirectional Frame Relay VC end-point. The ifIndex identifies an ifTable entry for a Frame Relay interface on this device.
Status: current	Access: not-accessible
OBJECT-TYPE
	CasfVcEndptEntry

casfVcEndptDlci		1.3.6.1.4.1.9.9.112.1.2.1.1.1
The value of the Data Link Connection Identifier (DLCI) which identifies this connection end-point.
Status: current	Access: not-accessible
OBJECT-TYPE
	DlciValue

casfVcEndptRxTrafficDescrRow		1.3.6.1.4.1.9.9.112.1.2.1.1.2
Identifies the entry in the casfTrafficDescrTable which applies to the receive direction at this connection end-point. For connections that negotiate traffic parameters through signaling (e.g. ABR connections), this object points to the desired traffic parameters, while the object casfVcEndptRxNegTrafficDescrRow points to the negotiated traffic parameters, for the receive direction.
Status: current	Access: read-create
OBJECT-TYPE
	CasfTrafficDescrRow

casfVcEndptTxTrafficDescrRow		1.3.6.1.4.1.9.9.112.1.2.1.1.3
Identifies the entry in the casfTrafficDescrTable which applies to the transmit direction at this connection end-point. For connections that negotiate traffic parameters through signaling (e.g. ABR connections), this object points to the desired traffic parameters, while the object casfVcEndptTxNegTrafficDescrRow points to the negotiated traffic parameter, for the transmit direction.
Status: current	Access: read-create
OBJECT-TYPE
	CasfTrafficDescrRow

casfVcEndptRxNegTrafficDescrRow		1.3.6.1.4.1.9.9.112.1.2.1.1.4
Identifies the entry in the casfTrafficDescrTable which contains negotiated traffic parameters applied to the receive direction of this connection end-point. This object is not instantiated if this is not the calling side of a soft VC, or if there is no traffic negotiation.
Status: current	Access: read-only
OBJECT-TYPE
	CasfTrafficDescrRow

casfVcEndptTxNegTrafficDescrRow		1.3.6.1.4.1.9.9.112.1.2.1.1.5
Identifies the entry in the casfTrafficDescrTable which contains negotiated traffic parameters applied to the transmit direction of this connection endpoint. This object is not instantiated if this is not the calling side of a soft VC, or if there is no traffic negotiation.
Status: current	Access: read-only
OBJECT-TYPE
	CasfTrafficDescrRow

casfVcEndptConnKind		1.3.6.1.4.1.9.9.112.1.2.1.1.6
The connection kind. The value can be set prior to the row becoming 'active'. To create a pvc connection endpoint, set this value to pvc(1). To create a soft VC connection endpoint, set this value to spvcInitiator(4), and specify the value of casfVcEndptSpvcRemoteAddr. The values svcIncoming(2), svcOutgoing(3), and spvcTarget(5) can not be written.
Status: current	Access: read-create
OBJECT-TYPE
	ConnectionKind

casfVcEndptIwfType		1.3.6.1.4.1.9.9.112.1.2.1.1.7
The type of the interworking function. The value can be set prior to the row becoming 'active'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	network(1), serviceTransparent(2), serviceTranslation(3), rfc1973(4)

casfVcEndptClpMode		1.3.6.1.4.1.9.9.112.1.2.1.1.8
Specifies how to map from Discard Eligibility (DE) bit on the Frame Relay side to Congestion Loss Priority (CLP) bit on the ATM side. For network interworking, clpIfDe(1) corresponds to Mode 1 as defined in FRF.5, section 4.4.1. clpIsZero(2) and clpIsOne(3) correspond to Mode 2 as defined in FRF.5, section 4.4.1. For service interworking, clpIfDe(1) corresponds to Mode 1 as defined in FRF.8, section 4.2.1. clpIsZero(2) and clpIsOne(3) correspond to Mode 2 as defined in FRF.8, section 4.2.1.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	clpIfDe(1), clpIsZero(2), clpIsOne(3)

casfVcEndptDeMode		1.3.6.1.4.1.9.9.112.1.2.1.1.9
Specifies how to map from Congestion Loss Priority (CLP) bit on the ATM side to Discard Eligibility (DE) bit on the Frame Relay side. See the Frame Relay Forum specifications FRF.5 and FRF.8 for definitions of Mode 1 and Mode 2. For network interworking, the valid values are: deIfClpOrFrsscsDe(1) -- Mode 1 of FRF.5 section 4.4.2 deIfFrsscsDe(2) -- Mode 2 of FRF.5 section 4.4.2 For service interworking, the valid values are: deIfClp(3) -- Mode 1 of FRF.8 section 4.2.2 deIsZero(4) and deIsOne(5) -- Mode 2 of FRF.8 section 4.2.2
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	deIfClpOrFrsscsDe(1), deIfFrsscsDe(2), deIfClp(3), deIsZero(4), deIsOne(5)

casfVcEndptEfciMode		1.3.6.1.4.1.9.9.112.1.2.1.1.10
Specifies how to map from FECN field in the Frame Relay PDU to the EFCI field in ATM cells, in case of service interworking. This object does not apply to network interworking. efciIfFecn(1) and efciIsZero(2) correspond to Mode 1 and Mode 2 (as defined in FRF.8, section 4.3.1.1), respectively.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	efciIfFecn(1), efciIsZero(2)

casfVcEndptUpcMode		1.3.6.1.4.1.9.9.112.1.2.1.1.11
Specifies the action taken by Usage Parameter Control (UPC) at the ingress port.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	pass(1), tagDrop(2), tag(3), drop(4)

casfVcEndptSpvcRemoteAddr		1.3.6.1.4.1.9.9.112.1.2.1.1.12
The ATM address of the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4). The agent will return an inconsistentValue error on sets if the value of casfVcEndptConnKind is other than spvcInitiator(4). If the value of casfVcEndptConnKind spvcTarget(5), this object is initialized by the agent. This object is instantiated only if the value of casfVcEndptConnKind is spvcInitiator(4) or spvcTarget(5).
Status: current	Access: read-create
OBJECT-TYPE
	AtmAddr

casfVcEndptSpvcRemoteType		1.3.6.1.4.1.9.9.112.1.2.1.1.13
The type of the remote end of the soft VC. This object is instantiated only if the value of casfVcEndptConnKind is spvcInitiator(4) or spvcTarget(5). The agent will return an inconsistentValue error on sets if the value of casfVcEndptConnKind is other than spvcInitiator(4) or spvcTarget(5).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	other(1), frameRelay(2), atm(3)

casfVcEndptSpvcRemoteDlci		1.3.6.1.4.1.9.9.112.1.2.1.1.14
The DLCI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteType is frameRelay(2). The object is instantiated only if the value of casfVcEndptSpvcRemoteType is frameRelay(2). The agent will return an inconsistentValue error on sets if the value of casfVcEndptSpvcRemoteType is other than frameRelay(2).
Status: current	Access: read-create
OBJECT-TYPE
	DlciValue

casfVcEndptSpvcRemoteVpi		1.3.6.1.4.1.9.9.112.1.2.1.1.15
The VPI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteType is atm(3). The object is instantiated only if the value of casfVcEndptSpvcRemoteType is atm(3). The agent will return an inconsistentValue error on sets if the value of casfVcEndptSpvcRemoteType is other than atm(3).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..255

casfVcEndptSpvcRemoteVci		1.3.6.1.4.1.9.9.112.1.2.1.1.16
The VCI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteType is atm(3). The object is instantiated only if the value of casfVcEndptSpvcRemoteType is atm(3). The agent will return an inconsistentValue error on sets if the value of casfVcEndptSpvcRemoteType is other than atm(3).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

casfVcEndptCreationTime		1.3.6.1.4.1.9.9.112.1.2.1.1.17
The time when this row was created.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

casfVcEndptRcvdSigStatus		1.3.6.1.4.1.9.9.112.1.2.1.1.18
The value of this object identifies the PVC status received via the local in-channel signaling procedures for this PVC end-point. This object is only pertinent for interfaces that perform the bidirectional procedures. For user-to-network network side procedures, the value of this object should be none(4).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	deleted(1), active(2), inactive(3), none(4)

casfVcEndptRowStatus		1.3.6.1.4.1.9.9.112.1.2.1.1.19
Used to create, modify or delete this row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

casfVcSignalStandardCalledIe		1.3.6.1.4.1.9.9.112.1.2.1.1.20
Specifies whether or not to signal the standard (from the ATM-Forum PNNI Soft PVC Addendum) format of the Called Soft PVC IE, as opposed to the proprietary encoding we have used for the network-interworking case to a frame-relay destination.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

casfFrLmiTable		1.3.6.1.4.1.9.9.112.1.3.1
This table contains frame relay Local Management Interface (LMI) parameters and counters. There is one entry for each frame relay interface. Entries come and go in this table as frame relay interfaces are created and deleted in the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CasfFrLmiEntry

casfFrLmiEntry		1.3.6.1.4.1.9.9.112.1.3.1.1
Frame relay LMI objects for a particular frame relay interface, which is identified by the ifIndex value in the INDEX clause.
Status: current	Access: not-accessible
OBJECT-TYPE
	CasfFrLmiEntry

casfFrLmiProtocol		1.3.6.1.4.1.9.9.112.1.3.1.1.1
Identifies the Local In-Channel Signaling Protocol that is used for this frame relay port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), lmi(2), ansiT1617D(3), ansiT1617B(4), ccittQ933A(5)

casfFrLmiType		1.3.6.1.4.1.9.9.112.1.3.1.1.2
Identifies the Local In-Channel Signaling Procedure that is used for this frame relay port. A dte performs only user-side procedures. A dce performs only network-side procedures. An nni performs bidirectional procedures.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dte(1), dce(2), nni(3)

casfFrLmiUserN391		1.3.6.1.4.1.9.9.112.1.3.1.1.3
Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

casfFrLmiUserN392		1.3.6.1.4.1.9.9.112.1.3.1.1.4
The maximum number of unanswered Status Enquiries the device shall accept before declaring the interface down.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

casfFrLmiUserN393		1.3.6.1.4.1.9.9.112.1.3.1.1.5
The number of status polling intervals over which the error threshold is counted. For example, if within N393 number of events the device receives N392 number of errors, the interface is marked as down.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

casfFrLmiUserT391		1.3.6.1.4.1.9.9.112.1.3.1.1.6
The number of seconds between successive status enquiry messages.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..30

casfFrLmiNetN392		1.3.6.1.4.1.9.9.112.1.3.1.1.7
The value of the network-side error threshold for this frame relay port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

casfFrLmiNetN393		1.3.6.1.4.1.9.9.112.1.3.1.1.8
The value of the network-side monitored events count for this frame relay port. If, within N393 number of events, the network-side receives N392 number of errors, the interface is marked as down.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..10

casfFrLmiNetT392		1.3.6.1.4.1.9.9.112.1.3.1.1.9
The value of the network-side polling verification timer for this frame relay port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..30

casfFrLmiEnquiryIns		1.3.6.1.4.1.9.9.112.1.3.1.1.10
Number of Status Enquiry messages received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfFrLmiEnquiryOuts		1.3.6.1.4.1.9.9.112.1.3.1.1.11
Number of Status Enquiry messages sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfFrLmiStatusIns		1.3.6.1.4.1.9.9.112.1.3.1.1.12
Number of Status messages received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfFrLmiStatusOuts		1.3.6.1.4.1.9.9.112.1.3.1.1.13
Number of Status messages sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfFrLmiStatusTimeouts		1.3.6.1.4.1.9.9.112.1.3.1.1.14
Number of times when timeout occurred on waiting for Status message
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfFrLmiStatusEnqTimeouts		1.3.6.1.4.1.9.9.112.1.3.1.1.15
Number of times when timeout occurred on waiting for Status Enquiry message
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfConfIfTable		1.3.6.1.4.1.9.9.112.1.3.2
Contains an entry for each Frame Relay interface that supports FR-ATM interworking connections. An entry contains interworking related parameters for the interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CasfConfIfEntry

casfConfIfEntry		1.3.6.1.4.1.9.9.112.1.3.2.1
Configuration parameters for interworking at a Frame Relay interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	CasfConfIfEntry

casfConfIfAtmAddress		1.3.6.1.4.1.9.9.112.1.3.2.1.1
The ATM Address that identifies this interface. This address can be used to setup soft VC's to this interface over an ATM network.
Status: current	Access: read-only
OBJECT-TYPE
	AtmAddr

casfConfIfUpcIntent		1.3.6.1.4.1.9.9.112.1.3.2.1.2
Specifies the default Usage Parameter Control (UPC) action to use at this interface for connections that do not explicitly specify a UPC action.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pass(1), tagDrop(2), tag(3), drop(4)

casfConfIfBcDefault		1.3.6.1.4.1.9.9.112.1.3.2.1.3
Specifies the default Committed Burst Size (Bc) value to use at this interface for connections that do not explicitly specify the value of Bc.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..32768

casfConfIfCledSpvcDeModeDef		1.3.6.1.4.1.9.9.112.1.3.2.1.4
Specifies the default mapping from Congestion Loss Priority (CLP) bit on the ATM side to Discard Eligibility (DE) bit on the Frame Relay side. This is used when receiving a soft PVC Setup using the standard encoding of the called Soft PVC IE. Otherwise a proprietary encoding provides this information.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	deIfClpOrFrsscsDe(1), deIfFrsscsDe(2)

casfConfIfCledSpvcClpModeDef		1.3.6.1.4.1.9.9.112.1.3.2.1.5
Specifies the default mapping from Discard Eligibility (DE) bit on the Frame Relay side to Congestion Loss Priority (CLP) bit on the ATM side.This is used when receiving a soft PVC Setup using the standard encoding of the called Soft PVC IE. Otherwise a proprietary encoding provides this information.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clpIfDe(1), clpIfIsZero(2), clpIfIsOne(3)

casfVcCountTable		1.3.6.1.4.1.9.9.112.1.4.1
A table containing counters at Frame Relay connection end-points. Entries in this table are created and deleted whenever corresponding entries in the casfVcEndptTable are created and deleted.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CasfVcCountEntry

casfVcCountEntry		1.3.6.1.4.1.9.9.112.1.4.1.1
Counters at a Frame Relay connection end-point, which is identified by the ifIndex of the Frame Relay interface and the DLCI number.
Status: current	Access: not-accessible
OBJECT-TYPE
	CasfVcCountEntry

casfVcCountReceivedFrames		1.3.6.1.4.1.9.9.112.1.4.1.1.1
Number of frames received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountReceivedOctets		1.3.6.1.4.1.9.9.112.1.4.1.1.2
Number of octets received. This counter counts octets from the beginning of the frame relay header field to the end of user data.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountReceivedFECNs		1.3.6.1.4.1.9.9.112.1.4.1.1.3
Number of frames received from the network with the FECN (Forward Explicit Congestion Notification) bit set.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountReceivedBECNs		1.3.6.1.4.1.9.9.112.1.4.1.1.4
Number of frames received from the network with the BECN (Backward Explicit Network Congestion) bit set.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountReceivedDEs		1.3.6.1.4.1.9.9.112.1.4.1.1.5
Number of frames received with the Discard Eligibility (DE) bit set.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountInDiscards		1.3.6.1.4.1.9.9.112.1.4.1.1.6
Number of frames received that were discarded at ingress. Possible reasons are policing, congestion.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountOutDiscards		1.3.6.1.4.1.9.9.112.1.4.1.1.7
Number of frames that were to be transmitted but were discarded. Possible reasons are policing, lack of buffers.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountSentFrames		1.3.6.1.4.1.9.9.112.1.4.1.1.8
Number of frames sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountSentOctets		1.3.6.1.4.1.9.9.112.1.4.1.1.9
Number of octets sent. This counter counts octets from the beginning of the frame relay header field to the end of user data.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountSentFECNs		1.3.6.1.4.1.9.9.112.1.4.1.1.10
Number of frames that were sent with the FECN bit set.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountSentBECNs		1.3.6.1.4.1.9.9.112.1.4.1.1.11
Number of frames sent with the BECN bit set.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountSentDEs		1.3.6.1.4.1.9.9.112.1.4.1.1.12
Number of frames sent with the DE bit set.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountTaggedFECNs		1.3.6.1.4.1.9.9.112.1.4.1.1.13
Number of frames for which the switch set the FECN bit.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountTaggedBECNs		1.3.6.1.4.1.9.9.112.1.4.1.1.14
Number of frames for which the switch set the BECN bit.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcCountTaggedDEs		1.3.6.1.4.1.9.9.112.1.4.1.1.15
Number of frames for which the switch set the DE bit.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcIwfCountTable		1.3.6.1.4.1.9.9.112.1.4.2
This table contains counters at the Frame Relay endpoint of FR-ATM interworking connections. There is an entry in this table corresponding to each entry in casfVcEndptTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CasfVcIwfCountEntry

casfVcIwfCountEntry		1.3.6.1.4.1.9.9.112.1.4.2.1
A set of counters at the Frame Relay endpoint of a FR-ATM interworking connection.
Status: current	Access: not-accessible
OBJECT-TYPE
	CasfVcIwfCountEntry

casfVcIwfCountInUnknownProts		1.3.6.1.4.1.9.9.112.1.4.2.1.1
Frames received with unknown protocol. This event is counted only for connections with service interworking in translation mode. For other types of connections, this count will remain at zero.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcIwfCountOutUnknownProts		1.3.6.1.4.1.9.9.112.1.4.2.1.2
Outbound frames that were not transmitted because they contained an unknown protocol. This event is counted only for connections with service interworking in translation mode. For other types of connections, this count will remain at zero.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcIwfCountReassemblyTimeouts		1.3.6.1.4.1.9.9.112.1.4.2.1.3
The number of frames which could not be completely reassembled due to a reassembly timeout, and were thus discarded before being transmitted on this connection.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcIwfCountLengthErrors		1.3.6.1.4.1.9.9.112.1.4.2.1.4
The number of reassembled frames intended to be transmitted on this connection for which the AAL5 PDU trailer length fields did not match the actual PDU length, and were thus discarded.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcIwfCountCrcErrors		1.3.6.1.4.1.9.9.112.1.4.2.1.5
The number of reassembled frames intended to be transmitted on this connection for which the AAL5 PDU had CRC errors, and were thus discarded.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfVcIwfCountTotalDiscardFrames		1.3.6.1.4.1.9.9.112.1.4.2.1.6
The number of frames intended to be transmitted on this connection that were discarded due to any reason including those described in other objects in this table (e.g., frames that were discarded because insufficient buffer space was available for reassembling the frame).
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

casfFAMapTable		1.3.6.1.4.1.9.9.112.1.5.1
This table provides mapping from a DLCI on a Frame Relay interface to a VPI/VCI on an internal ATM interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CasfFAMapEntry

casfFAMapEntry		1.3.6.1.4.1.9.9.112.1.5.1.1
Given the ifIndex of a frame relay interface, and a DLCI on that interface, this entry provides the ifIndex and VPI/VCI on the corresponding internal atm interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	CasfFAMapEntry

casfFAMapDlci		1.3.6.1.4.1.9.9.112.1.5.1.1.1
The DLCI value.
Status: current	Access: not-accessible
OBJECT-TYPE
	DlciValue

casfFAMapInternalAtmInterface		1.3.6.1.4.1.9.9.112.1.5.1.1.2
The ifIndex of the internal ATM interface to which this DLCI is mapped.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

casfFAMapInternalAtmVpi		1.3.6.1.4.1.9.9.112.1.5.1.1.3
The VPI value to which this DLCI is mapped.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

casfFAMapInternalAtmVci		1.3.6.1.4.1.9.9.112.1.5.1.1.4
The VCI value to which this DLCI is mapped.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

casfAFMapTable		1.3.6.1.4.1.9.9.112.1.5.2
This table provides mapping from an atmVclEntry on an internal ATM internal to a casfVcEndptEntry on a Frame Relay interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CasfAFMapEntry

casfAFMapEntry		1.3.6.1.4.1.9.9.112.1.5.2.1
Given the ifIndex of an internal ATM interface, and VPI/VCI, provides the ifIndex of a Frame Relay interface and DLCI, if such mapping exists. The value of ifType for an internal ATM interface is propVirtual(53). For every such interface on the switch, this table contains an entry for each virtual channel link (VCL) that maps to a frame relay connection. Entries in this table come and go as the corresponding frame relay connections come and go.
Status: current	Access: not-accessible
OBJECT-TYPE
	CasfAFMapEntry

casfAFMapAtmVpi		1.3.6.1.4.1.9.9.112.1.5.2.1.1
The VPI value of the Virtual Channel Link (VCL) on the ATM interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..255

casfAFMapAtmVci		1.3.6.1.4.1.9.9.112.1.5.2.1.2
The VCI value of the Virtual Channel Link (VCL) on the ATM interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

casfAFMapFrIndex		1.3.6.1.4.1.9.9.112.1.5.2.1.3
The ifIndex of the frame relay interface that this VCL maps to.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

casfAFMapFrDlci		1.3.6.1.4.1.9.9.112.1.5.2.1.4
The DLCI on the frame relay interface that this VCL maps to.
Status: current	Access: read-only
OBJECT-TYPE
	DlciValue

ciscoAtmSFrIwfMIBConformance		1.3.6.1.4.1.9.9.112.3
OBJECT IDENTIFIER

ciscoAtmSFrIwfMIBCompliances		1.3.6.1.4.1.9.9.112.3.1
OBJECT IDENTIFIER

ciscoAtmSFrIwfMIBGroups		1.3.6.1.4.1.9.9.112.3.2
OBJECT IDENTIFIER

ciscoAtmSFrIwfMIBCompliance		1.3.6.1.4.1.9.9.112.3.1.1
The compliance statement for entities which implement the Cisco Atm Switch FR IWF MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

ciscoAtmSFrIwfConfConnGroup		1.3.6.1.4.1.9.9.112.3.2.1
A collection of objects which allow configuration of FR-ATM connections on an ATM switch.
Status: current	Access: read-only
OBJECT-GROUP

ciscoAtmSFrIwfLmiGroup		1.3.6.1.4.1.9.9.112.3.2.2
A collection of objects for configuring and monitoring LMI on an FR interface.
Status: current	Access: read-only
OBJECT-GROUP

ciscoAtmSFrIwfConfIfGroup		1.3.6.1.4.1.9.9.112.3.2.3
A collection of objects which allow configuration of interworking related parameters on an FR interface.
Status: current	Access: read-only
OBJECT-GROUP

ciscoAtmSFrIwfVcStatsGroup		1.3.6.1.4.1.9.9.112.3.2.4
A collection of counters at FR VC end-points.
Status: current	Access: read-only
OBJECT-GROUP

ciscoAtmSFrIwfVcIwStatsGroup		1.3.6.1.4.1.9.9.112.3.2.5
A collection of counters related to FR-ATM interworking at FR VC end-points.
Status: current	Access: read-only
OBJECT-GROUP

ciscoAtmSFrIwfMappingGroup		1.3.6.1.4.1.9.9.112.3.2.6
A collection of objects that describe the mapping from a FR connection end-point to an ATM VCL, and vice versa.
Status: current	Access: read-only
OBJECT-GROUP