CISCO-CALL-TRACKER-MIB

File: CISCO-CALL-TRACKER-MIB.mib (60281 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
CISCO-SMI DIAL-CONTROL-MIB

Imported symbols

MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE
IpAddress Gauge32 Integer32
Unsigned32 MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP DisplayString TimeStamp
TruthValue TEXTUAL-CONVENTION ciscoMgmt
AbsoluteCounter32

Defined Types

CctCallId  
Represents a Call Identifier. The call identifier is a monotonically assigned, positive integer which uniquely identifies the call within the system.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

CctServiceType  
Represents possible service types. none - No service associated with call. other - Service active, but none of the following. slip - Serial Line IP ppp - PPP mp - Multilink PPP (RFC 1990) tcpClear - Byte stream over TCP telnet - TELNET exec - terminal server l2f - Virtual Private Data Network service (VPDN) using Layer 2 Forwarding protocol l2tp - Virtual Private Data Network service (VPDN) using Layer 2 Tunneling Protocol
TEXTUAL-CONVENTION    
  INTEGER none(1), other(2), slip(3), ppp(4), mp(5), tcpClear(6), telnet(7), exec(8), l2f(9), l2tp(10)  

CctCallCategory  
Represents possible call categories or types. none - No call category associated with call other - None of the following modem - Modem call isdn-sync - ISDN sync digital call Now mapped to syncData v110 - V110 Call v120 - V120 Call cas-digital - Channel Associated Signaling (CAS) 56k data call mgcpData - MGCP data call Now mapped to syncData syncData - Sync digital data call for any call control lapb-ta - LAPB or LAPB-TA call
TEXTUAL-CONVENTION    
  INTEGER none(1), other(2), modem(3), isdnSync(4), v110(5), v120(6), casDigital(7), mgcpData(8), syncData(9), lapb-ta(10)  

CctCallSigType  
Represents supported signaling types for a call. Unknown - Signaling origin of call type unknown. External - Signaling origin of call type by external agent e.g. MGCP, H.248 Q931 - Signaling origin of call type by Q.931/ISDN Autodetect - Signaling of call type by automatic detection
TEXTUAL-CONVENTION    
  INTEGER unknown(1), external(2), q931(3), autoDetect(4)  

CctActiveEntry  
SEQUENCE    
  cctActiveCallId CctCallId
  cctActiveSetupTime TimeStamp
  cctActiveOrigin INTEGER
  cctActiveConnectionTime TimeStamp
  cctActivePhysicalLayerReadyTime TimeStamp
  cctActiveServiceUpTime TimeStamp
  cctActiveServiceType CctServiceType
  cctActiveUserValidationTime TimeStamp
  cctActiveUserId DisplayString
  cctActiveUserIpAddr IpAddress
  cctActiveUserSubnetMask IpAddress
  cctActiveAccountingSessionId DisplayString
  cctActiveCallCategory CctCallCategory
  cctActiveInitialRxRate Unsigned32
  cctActiveInitialTxRate Unsigned32
  cctActiveResourceSlot Integer32
  cctActiveResourcePort Integer32
  cctActiveEntrySlot Integer32
  cctActiveEntryPort Integer32
  cctActiveEntryDs1 Integer32
  cctActiveEntryChannel Integer32
  cctActiveCalledPartyId DisplayString
  cctActiveCallingPartyId DisplayString
  cctActiveMpBundleId Unsigned32
  cctActiveChargedUnits AbsoluteCounter32
  cctActiveReceiveBytes AbsoluteCounter32
  cctActiveTransmitBytes AbsoluteCounter32
  cctActiveCallSignalingType CctCallSigType

CctHistoryEntry  
SEQUENCE    
  cctHistoryIndex Unsigned32
  cctHistoryCallId CctCallId
  cctHistorySetupTime TimeStamp
  cctHistoryOrigin INTEGER
  cctHistoryConnectionTime TimeStamp
  cctHistoryPhysicalLayerReadyTime TimeStamp
  cctHistoryServiceUpTime TimeStamp
  cctHistoryServiceType CctServiceType
  cctHistoryUserValidationTime TimeStamp
  cctHistoryUserId DisplayString
  cctHistoryUserIpAddr IpAddress
  cctHistoryUserSubnetMask IpAddress
  cctHistoryAccountingSessionId DisplayString
  cctHistoryCallCategory CctCallCategory
  cctHistoryInitialRxRate Unsigned32
  cctHistoryInitialTxRate Unsigned32
  cctHistoryResourceSlot Integer32
  cctHistoryResourcePort Integer32
  cctHistoryEntrySlot Integer32
  cctHistoryEntryPort Integer32
  cctHistoryEntryDs1 Integer32
  cctHistoryEntryChannel Integer32
  cctHistoryCalledPartyId DisplayString
  cctHistoryCallingPartyId DisplayString
  cctHistoryMpBundleId Unsigned32
  cctHistoryChargedUnits Gauge32
  cctHistoryReceiveBytes Gauge32
  cctHistoryTransmitBytes Gauge32
  cctHistoryDisconnectTime TimeStamp
  cctHistoryDisconnectReasonText DisplayString
  cctHistoryCallSignalingType CctCallSigType

Defined Values

ciscoCallTrackerMIB 1.3.6.1.4.1.9.9.163
This MIB module provides information for tracking the progress and status of a data call from the hardware layer through the application or service layer. A data call is a call setup via a signaling protocol (e.g., ISDN D Channel signaling) on the Public Switching Telephony Network to a Network Access Server in order to transfer data, either as a byte stream (e.g., terminal emulation) or in a packet format (e.g., PPP packets) from a data terminal (e.g., Personal Computer) to a data network (e.g., Internet).
MODULE-IDENTITY    

cctMIBObjects 1.3.6.1.4.1.9.9.163.1
OBJECT IDENTIFIER    

cctGeneral 1.3.6.1.4.1.9.9.163.1.1
OBJECT IDENTIFIER    

cctActive 1.3.6.1.4.1.9.9.163.1.2
OBJECT IDENTIFIER    

cctHistory 1.3.6.1.4.1.9.9.163.1.3
OBJECT IDENTIFIER    

cctNotificationConfig 1.3.6.1.4.1.9.9.163.1.4
OBJECT IDENTIFIER    

cctCallIdPrefix 1.3.6.1.4.1.9.9.163.1.1.1
This object may be used in conjunction with objects of type CctCallId to provide call references which are unique across system re-initializations. This value is generated at system re-initialization. It is a 32-bit random number, with very low likely-hood of repeating within the lifetime of the system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cctActiveTableNumberEntries 1.3.6.1.4.1.9.9.163.1.2.1
The number of entries currently in the cctActiveTable.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cctActiveTableHighWaterMark 1.3.6.1.4.1.9.9.163.1.2.2
Maximum number of entries present in cctActiveTable since last system re-initialization. This corresponds to the maximum value reported by cctActiveTableNumberEntries.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cctActiveTable 1.3.6.1.4.1.9.9.163.1.2.3
This table contains entries for active calls in the system. All such calls either originate or terminate at this system. The table is indexed by call ID assigned to the call.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CctActiveEntry

cctActiveEntry 1.3.6.1.4.1.9.9.163.1.2.3.1
The information regarding a single call. Entries are created when a setup request is first received by the system. Entries are removed when a call is terminated or rejected. A corresponding entry is created in the cctHistoryTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CctActiveEntry  

cctActiveCallId 1.3.6.1.4.1.9.9.163.1.2.3.1.1
Represents a Call Identifier. The call identifier is a monotonically increasing unsigned integer which uniquely identifies the call within the system. The Call ID is represented as an unsigned 32-bit integer. After 4,294,967,295 calls, the ID will wrap and the 4,294,967,296th call will receive the next smallest available id starting from 1. Zero is not a valid value.
Status: current Access: not-accessible
OBJECT-TYPE    
  CctCallId  

cctActiveSetupTime 1.3.6.1.4.1.9.9.163.1.2.3.1.2
Value of sysUpTime when the call is first made known to the system.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctActiveOrigin 1.3.6.1.4.1.9.9.163.1.2.3.1.3
This object indicates how the call was created. originate(1) - The call was initiated locally with the system sending the setup request. Dialout answer(2) - The call was initiated remotely and the system received the setup request. Dialin
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER originate(1), answer(2)  

cctActiveConnectionTime 1.3.6.1.4.1.9.9.163.1.2.3.1.4
Value of sysUpTime when the system connected the call.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctActivePhysicalLayerReadyTime 1.3.6.1.4.1.9.9.163.1.2.3.1.5
Value of sysUpTime when the physical layer for the call achieved a steady state and the call is ready for higher protocol layers to begin. In the case of modem calls, the physical layer for the call achieves a steady state when the data rates, modulations, and error correcting protocols have been negotiated between the originating and answering modems. This is primarily intended for calls which connect to a processing resource identified by cctActiveResourceSlot and cctActiveResourcePort. It also applies to digital calls using adaptive rate technologies such as V.110 and V.120.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctActiveServiceUpTime 1.3.6.1.4.1.9.9.163.1.2.3.1.6
Value of sysUpTime when the call service type identified in cctActiveServiceType was established.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctActiveServiceType 1.3.6.1.4.1.9.9.163.1.2.3.1.7
Service associated with the call. This is the highest level of service known to the system for the call. The service represents the encapsulation protocol layer active for the call. In the case of multiple services on a given call, the last service activated will be reported.
Status: current Access: read-only
OBJECT-TYPE    
  CctServiceType  

cctActiveUserValidationTime 1.3.6.1.4.1.9.9.163.1.2.3.1.8
Value of sysUpTime when the user identification associated with this call was validated. See cctActiveUserId for description of user identification.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctActiveUserId 1.3.6.1.4.1.9.9.163.1.2.3.1.9
The User login ID or zero length string if unavailable.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cctActiveUserIpAddr 1.3.6.1.4.1.9.9.163.1.2.3.1.10
The IP address assigned to the cctActiveUserId for this call or 0.0.0.0 if not applicable or unavailable.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

cctActiveUserSubnetMask 1.3.6.1.4.1.9.9.163.1.2.3.1.11
The IP subnet mask assigned to the cctActiveUserId for this call or 0.0.0.0 if not applicable or unavailable.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

cctActiveAccountingSessionId 1.3.6.1.4.1.9.9.163.1.2.3.1.12
Accounting session identification assigned to this call by AAA. The session ID is sent by AAA to RADIUS as the Acct-Session-Id attribute or TACACS+ as the task_id. If no accounting session ID is assigned, the value is a null string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cctActiveCallCategory 1.3.6.1.4.1.9.9.163.1.2.3.1.13
The call category or type
Status: current Access: read-only
OBJECT-TYPE    
  CctCallCategory  

cctActiveInitialRxRate 1.3.6.1.4.1.9.9.163.1.2.3.1.14
Initial receive data rate for this call. If call is a synchronous digital call such as ISDN sync, this value is the data rate of the B-channel. If call is asynchronous, even if using a synchronous transmission medium such as ISDN, the value is determined by the resource providing the asynchronous processing. For modem calls, this value corresponds to the value of cmRXRate from CISCO-MODEM-MGMT-MIB, immediately after the modem has completed initial negotiations. This value does not change, even if the data rate varies during the call. This value will be zero until an initial data rate has been determined.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cctActiveInitialTxRate 1.3.6.1.4.1.9.9.163.1.2.3.1.15
Initial transmit data rate for this call. If call is a synchronous digital call such as ISDN sync, this value is the data rate of the B-channel. If call is asynchronous, even if using a synchronous transmission medium such as ISDN, the value is determined by the resource providing the asynchronous processing. For modem calls, this value corresponds to the value of cmTXRate from CISCO-MODEM-MGMT-MIB, immediately after the modem has completed initial negotiations. This value does not change, even if the data rate varies during the call. This value will be zero until an initial data rate has been determined.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cctActiveResourceSlot 1.3.6.1.4.1.9.9.163.1.2.3.1.16
Identification of the processing resource allocated to the call. In the case of a call requiring a modem resource, this is the value of cmSlotIndex from CISCO-MODEM-MGMT-MIB. This value along with cctActiveResourcePort uniquely identifies a resource port. Value is -1 if call does not utilize such a resource.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..214783647  

cctActiveResourcePort 1.3.6.1.4.1.9.9.163.1.2.3.1.17
Identification of the processing resource allocated to the call. In the case of a call requiring a modem resource, this is the value of cmPortIndex from CISCO-MODEM-MGMT-MIB. This value along with cctActiveResourceSlot uniquely identifies a resource port. Value is -1 if call does not utilize such a resource.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..214783647  

cctActiveEntrySlot 1.3.6.1.4.1.9.9.163.1.2.3.1.18
The device slot containing the port on which the call exists.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..214783647  

cctActiveEntryPort 1.3.6.1.4.1.9.9.163.1.2.3.1.19
The physical port within the device slot on which the call exists.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..214783647  

cctActiveEntryDs1 1.3.6.1.4.1.9.9.163.1.2.3.1.20
The DS1 link containing the call. This may be a DS1 contained within a larger grouping of multiple DS1s within a single physical port. If the physical port is of type DS1, this value is identical to cctActiveEntryPort. If the DS1 is a logical subinterface within the physical port, this value is the number of the DS1 within this slot. Examples: 8 port DS1 card - cctActiveEntryPort and cctActiveEntryDs1 will have identical values. 3 port T3 card - cctActiveEntryPort represents T3 ports. cctActiveEntryEntryDs1 represents logical T1 interfaces. Each T3 contains 28 T1 interfaces. The T1 interfaces are numbered sequentially across the entire T3 card.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..214783647  

cctActiveEntryChannel 1.3.6.1.4.1.9.9.163.1.2.3.1.21
The channel or timeslot within the cctActiveEntryDs1 allocated to the call.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..214783647  

cctActiveCalledPartyId 1.3.6.1.4.1.9.9.163.1.2.3.1.22
The called telephone number for this call. For calls answered by the system, this corresponds to the Dialed Number Identification (DNIS). For calls originated by the system, this is the destination number. If not available this is a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

cctActiveCallingPartyId 1.3.6.1.4.1.9.9.163.1.2.3.1.23
The calling telephone number for this call. For calls answered by the system, this corresponds to the calling identification (CLID). For calls originated by the system, this is the number associated with the device. For the interworking call, this object contains the translated calling party number if there is a translation rule is associated with dial plan for making this outgoing call. If not available this is a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

cctActiveMpBundleId 1.3.6.1.4.1.9.9.163.1.2.3.1.24
Multilink PPP bundle identification for call if cctActiveServiceType has the value 'mp'. If the value of cctActiveServiceType for this call is not 'mp', then the value of this object is not meaningful.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cctActiveChargedUnits 1.3.6.1.4.1.9.9.163.1.2.3.1.25
The number of charged units for this connection. For incoming calls or if charging information is not supplied by the switch, the value of this object will be zero.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cctActiveReceiveBytes 1.3.6.1.4.1.9.9.163.1.2.3.1.26
The number of bytes received on the call. All the 'raw' bytes are counted including any protocol headers which may or may not be present depending on the value of cctActiveServiceType.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cctActiveTransmitBytes 1.3.6.1.4.1.9.9.163.1.2.3.1.27
The number of bytes transmitted on the call. All the 'raw' bytes are counted including any protocol headers which may or may not be present depending on the value of cctActiveServiceType.
Status: current Access: read-only
OBJECT-TYPE    
  AbsoluteCounter32  

cctActiveCallSignalingType 1.3.6.1.4.1.9.9.163.1.2.3.1.28
Signaling type used to setup the call.
Status: current Access: read-only
OBJECT-TYPE    
  CctCallSigType  

cctHistoryTableEntriesLimit 1.3.6.1.4.1.9.9.163.1.3.1
The upper limit on the number of entries that the cctHistoryTable may contain. A value of zero will prevent any history from being retained. This value may not exceed the system specific limit provided in cctHistoryTableMaxEntries.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2147483647  

cctHistoryTableMaxEntries 1.3.6.1.4.1.9.9.163.1.3.2
The maximum allowed table length supported by this system. The value of cctHistoryTableEntriesLimit may not exceed this value.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cctHistoryTableRetainTimer 1.3.6.1.4.1.9.9.163.1.3.3
The maximum amount of time that an entry will be maintained within the cctHistoryTable before being deleted. A value of zero will prevent any history from being retained.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2147483647  

cctHistoryTableNumberEntries 1.3.6.1.4.1.9.9.163.1.3.4
Count of the number of entries currently in the cctHistoryTable.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cctHistoryTableHighWaterMark 1.3.6.1.4.1.9.9.163.1.3.5
Maximum number of entries present in cctHistoryTable since last system re-initialization or the value of cctHistoryTableEntriesLimit has been changed. This corresponds to the maximum value reported by cctHistoryTableNumberEntries. Changing the value of cctHistoryTableEntriesLimit resets this value to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cctHistoryTableNewestIndex 1.3.6.1.4.1.9.9.163.1.3.6
This object provides the index value of the most recent entry currently in the cctHistoryTable. A value of zero indicates there has never been an entry in the table or all entries have expired.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cctHistoryTable 1.3.6.1.4.1.9.9.163.1.3.7
This table provides information on terminated calls.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CctHistoryEntry

cctHistoryEntry 1.3.6.1.4.1.9.9.163.1.3.7.1
The information regarding a single terminated call. An entry of this table is created when the system initiates, detects, or is notified of a call termination. Resources allocated to the call may still be in use by the call when the entry is created. An entry is deleted when it has existed in this table longer than cctHistoryTableRetainTimer minutes. An entry is also removed if the table is full and a new entry needs to be created to accommodate a terminated call. The oldest entry in the table will be deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  CctHistoryEntry  

cctHistoryIndex 1.3.6.1.4.1.9.9.163.1.3.7.1.1
A monotonically increasing integer for the sole purpose of indexing terminated calls. When it reaches the maximum value the agent wraps the value back to 1 and will flush existing entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cctHistoryCallId 1.3.6.1.4.1.9.9.163.1.3.7.1.2
The call identifier for the call. This is the same value assigned to the call in cctActiveCallId when it was in the cctActiveTable. It is possible for two cctHistoryEntry entries to have the same cctHistoryCallId if one very long running call terminates after the cctActiveCallId has wrapped around and is reassigned to a new short lived call.
Status: current Access: read-only
OBJECT-TYPE    
  CctCallId  

cctHistorySetupTime 1.3.6.1.4.1.9.9.163.1.3.7.1.3
Value of sysUpTime when the call was first made known to the system.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctHistoryOrigin 1.3.6.1.4.1.9.9.163.1.3.7.1.4
This object indicates how the call was created. originate(1) - The call was initiated locally with the system sending the setup request. Dialout answer(2) - The call was initiated remotely and the system received the setup request. Dialin
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER originate(1), answer(2)  

cctHistoryConnectionTime 1.3.6.1.4.1.9.9.163.1.3.7.1.5
Value of sysUpTime when the system connected the call.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctHistoryPhysicalLayerReadyTime 1.3.6.1.4.1.9.9.163.1.3.7.1.6
Value of sysUpTime when the physical layer for the call achieved a steady state and the call is ready for higher protocol layers to begin. In the case of modem calls, the physical layer for the call achieves a steady state when the data rates, modulations, and error correcting protocols have been negotiated between the originating and answering modems. This is primarily intended for calls which connect to a processing resource identified by cctHistoryResourceSlot and cctHistoryResourcePort. It also applies to digital calls using adaptive rate technologies such as V.110 and V.120.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctHistoryServiceUpTime 1.3.6.1.4.1.9.9.163.1.3.7.1.7
Value of sysUpTime when the call service type identified in cctHistoryServiceType was established.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctHistoryServiceType 1.3.6.1.4.1.9.9.163.1.3.7.1.8
Service associated with the call. This is the highest level of service known to the system for the call. The service represents the encapsulation protocol layer active for the call. In the case of multiple services on a given call, the last service activated will be reported.
Status: current Access: read-only
OBJECT-TYPE    
  CctServiceType  

cctHistoryUserValidationTime 1.3.6.1.4.1.9.9.163.1.3.7.1.9
Value of sysUpTime when the user identification associated with this call was validated. See cctHistoryUserId for description of user identification.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctHistoryUserId 1.3.6.1.4.1.9.9.163.1.3.7.1.10
The User login ID or zero length string if unavailable. If this contains a non-zero length string, and cctHistoryUserValidationTime is zero, then the user failed validation.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cctHistoryUserIpAddr 1.3.6.1.4.1.9.9.163.1.3.7.1.11
The IP address assigned to the cctHistoryUserId for this call or 0.0.0.0 if not applicable or unavailable.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

cctHistoryUserSubnetMask 1.3.6.1.4.1.9.9.163.1.3.7.1.12
The IP subnet mask assigned to the cctHistoryUserId for this call or 0.0.0.0 if not applicable or unavailable.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

cctHistoryAccountingSessionId 1.3.6.1.4.1.9.9.163.1.3.7.1.13
Accounting session identification assigned to this call by AAA. The session ID is sent by AAA to RADIUS as the Acct-Session-Id attribute or TACACS+ as the task_id. If no accounting session ID is assigned, the value is a null string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cctHistoryCallCategory 1.3.6.1.4.1.9.9.163.1.3.7.1.14
The call category or type
Status: current Access: read-only
OBJECT-TYPE    
  CctCallCategory  

cctHistoryInitialRxRate 1.3.6.1.4.1.9.9.163.1.3.7.1.15
Initial receive data rate for this call. If call is a synchronous digital call such as ISDN sync, this value is the data rate of the B-channel. If call is asynchronous, even if using a synchronous transmission medium such as ISDN, the value is determined by the resource providing the asynchronous processing. For modem calls, this value corresponds to the value of cmRXRate from CISCO-MODEM-MGMT-MIB, immediately after the modem has completed initial negotiations. This value does not change, even if the data rate varies during the call. This value will be zero if the call terminated prior to an initial data rate determination.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cctHistoryInitialTxRate 1.3.6.1.4.1.9.9.163.1.3.7.1.16
Initial transmit data rate for this call. If call is a synchronous digital call such as ISDN sync, this value is the data rate of the B-channel. If call is asynchronous, even if using a synchronous transmission medium such as ISDN, the value is determined by the resource providing the asynchronous processing. For modem calls, this value corresponds to the value of cmTXRate from CISCO-MODEM-MGMT-MIB, immediately after the modem has completed initial negotiations. This value does not change, even if the data rate varies during the call. This value will be zero if the call terminated prior to an initial data rate determination.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cctHistoryResourceSlot 1.3.6.1.4.1.9.9.163.1.3.7.1.17
Identification of processing resource allocated to call. In the case of a call requiring a modem resource, this is the value of cmSlotIndex from CISCO-MODEM-MGMT-MIB. This value along with cctHistoryResourcePort uniquely identifies a resource port. Value is -1 if call does not utilize such a resource.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..214783647  

cctHistoryResourcePort 1.3.6.1.4.1.9.9.163.1.3.7.1.18
Identification of processing resource allocated to call. In the case of a call requiring a modem resource, this is the value of cmPortIndex from CISCO-MODEM-MGMT-MIB. This value along with cctHistoryResourceSlot uniquely identifies a resource port. Value is -1 if call does not utilize such a resource.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..214783647  

cctHistoryEntrySlot 1.3.6.1.4.1.9.9.163.1.3.7.1.19
The device slot containing the port on which the call existed.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..214783647  

cctHistoryEntryPort 1.3.6.1.4.1.9.9.163.1.3.7.1.20
The physical port within the device slot on which the call existed.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..214783647  

cctHistoryEntryDs1 1.3.6.1.4.1.9.9.163.1.3.7.1.22
The DS1 link containing the call. This may be a DS1 contained within a larger grouping of multiple DS1s within a single physical port. If the physical port is of type DS1, this value is identical to cctActiveEntryPort. If the DS1 is a logical subinterface within the physical port, this value is the number of the DS1 within this slot. Examples: 8 port DS1 card - cctActiveEntryPort and cctActiveEntryDs1 will have identical values. 3 port T3 card - cctActiveEntryPort represents T3 ports. cctActiveEntryEntryDs1 represents logical T1 interfaces. Each T3 contains 28 T1 interfaces. The T1 interfaces are numbered sequentially across the entire T3 card.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..214783647  

cctHistoryEntryChannel 1.3.6.1.4.1.9.9.163.1.3.7.1.23
The channel or timeslot within the cctHistoryEntryDs1 which was allocated to the call.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..214783647  

cctHistoryCalledPartyId 1.3.6.1.4.1.9.9.163.1.3.7.1.24
The called telephone number for this call. For calls answered by the system, this corresponds to the Dialed Number Identification (DNIS). For calls originated by the system, this is the destination number. If not available the string length is zero.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

cctHistoryCallingPartyId 1.3.6.1.4.1.9.9.163.1.3.7.1.25
The calling telephone number for this call. For calls answered by the system, this corresponds to the calling identification (CLID). For calls originated by the system, this is the number associated with the device. For the interworking call, this object contains the translated calling party number if there is a translation rule is associated with dial plan for making this outgoing call. If not available this is a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

cctHistoryMpBundleId 1.3.6.1.4.1.9.9.163.1.3.7.1.26
Multilink PPP bundle identification for call if cctHistoryServiceType has the value 'mp'. If the value of cctHistoryServiceType for this call is not 'mp', then the value of this object is not meaningful.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cctHistoryChargedUnits 1.3.6.1.4.1.9.9.163.1.3.7.1.27
The number of charged units for this connection. For incoming calls or if charging information is not supplied by the switch, the value of this object will be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cctHistoryReceiveBytes 1.3.6.1.4.1.9.9.163.1.3.7.1.28
The number of bytes received on the call. All the 'raw' bytes are counted including any protocol headers which may or may not be present depending on the value of cctHistoryServiceType.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cctHistoryTransmitBytes 1.3.6.1.4.1.9.9.163.1.3.7.1.29
The number of bytes transmitted on the call. All the 'raw' bytes are counted including any protocol headers which may or may not be present depending on the value of cctHistoryServiceType.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cctHistoryDisconnectTime 1.3.6.1.4.1.9.9.163.1.3.7.1.30
Value of sysUpTime when call was disconnected. This is when the system initiates, detects, or is notified of call termination. This is the call duration from initial setup request.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cctHistoryDisconnectReasonText 1.3.6.1.4.1.9.9.163.1.3.7.1.31
Text description of the disconnect reason provided. Value is zero-length string if no text is available.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cctHistoryCallSignalingType 1.3.6.1.4.1.9.9.163.1.3.7.1.32
Signaling type used to setup the call.
Status: current Access: read-only
OBJECT-TYPE    
  CctCallSigType  

cctCallSetupTermNotifyEnable 1.3.6.1.4.1.9.9.163.1.4.1
This variable controls generation of cctCallSetupNotification and cctCallTerminateNotification. When this variable is 'true(1)', generation of these notifications is enabled. When this variable is 'false(2)', generation is disabled. The default value is 'false(2)'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cctMIBNotificationPrefix 1.3.6.1.4.1.9.9.163.2
OBJECT IDENTIFIER    

cctMIBNotifications 1.3.6.1.4.1.9.9.163.2.0
OBJECT IDENTIFIER    

cctCallSetupNotification 1.3.6.1.4.1.9.9.163.2.0.1
A Call Tracker Setup notification is generated whenever a new active call entry is created in the cctActiveTable.
Status: current Access: read-write
NOTIFICATION-TYPE    

cctCallTerminateNotification 1.3.6.1.4.1.9.9.163.2.0.2
A Call Tracker Terminate notification is generated whenever a new history call entry is created in the cctHistoryTable.
Status: current Access: read-write
NOTIFICATION-TYPE    

cctMIBConformance 1.3.6.1.4.1.9.9.163.3
OBJECT IDENTIFIER    

cctMIBCompliances 1.3.6.1.4.1.9.9.163.3.1
OBJECT IDENTIFIER    

cctMIBGroups 1.3.6.1.4.1.9.9.163.3.2
OBJECT IDENTIFIER    

cctMIBCompliance 1.3.6.1.4.1.9.9.163.3.1.1
The compliance statement for entities which implement the CISCO CALL TRACKER MIB
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

cctMIBComplianceRev1 1.3.6.1.4.1.9.9.163.3.1.2
The compliance statement for entities which implement the CISCO CALL TRACKER MIB
Status: current Access: read-write
MODULE-COMPLIANCE    

cctGeneralGroup 1.3.6.1.4.1.9.9.163.3.2.1
A collection of objects providing the general information.
Status: current Access: read-write
OBJECT-GROUP    

cctActiveGroup 1.3.6.1.4.1.9.9.163.3.2.2
A collection of objects providing the active call information.
Status: deprecated Access: read-write
OBJECT-GROUP    

cctHistoryGroup 1.3.6.1.4.1.9.9.163.3.2.3
A collection of objects providing the historical call information.
Status: deprecated Access: read-write
OBJECT-GROUP    

cctNotificationConfigGroup 1.3.6.1.4.1.9.9.163.3.2.4
A collection of objects providing the notification configuration.
Status: current Access: read-write
OBJECT-GROUP    

cctNotificationGroup 1.3.6.1.4.1.9.9.163.3.2.5
The collection of notifications used for call status changes.
Status: current Access: read-write
NOTIFICATION-GROUP    

cctActiveGroupRev1 1.3.6.1.4.1.9.9.163.3.2.6
A collection of objects providing the active call information.
Status: current Access: read-write
OBJECT-GROUP    

cctHistoryGroupRev1 1.3.6.1.4.1.9.9.163.3.2.7
A collection of objects providing the historical call information.
Status: current Access: read-write
OBJECT-GROUP