CISCO-DSL-PROVISION-MIB

File: CISCO-DSL-PROVISION-MIB.mib (66865 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	IF-MIB
SNMPv2-CONF	CISCO-SMI

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Integer32
Gauge32	Unsigned32	IpAddress
DisplayString	RowStatus	TruthValue
ifIndex	InterfaceIndexOrZero	MODULE-COMPLIANCE
OBJECT-GROUP	ciscoExperiment

Defined Types

CdslNrpIpAddressEntry
SEQUENCE
	cdslNrpSlotIndex	Integer32
	cdslNrpIpAddress	IpAddress

CdslVirtualTemplateNumberEntry
SEQUENCE
	cdslMaxVirtualTemplates	Unsigned32
	cdslVirtualTemplates	Gauge32

CdslVirtualTemplateEntry
SEQUENCE
	cdslVTIndex	Integer32
	cdslVTIpAddressMethod	INTEGER
	cdslVTIpAddress	IpAddress
	cdslVTIpAddressMask	IpAddress
	cdslVTIpIfIndex	InterfaceIndexOrZero
	cdslVTPeerIpAddressMethod	INTEGER
	cdslVTPeerIpAddrPool	DisplayString
	cdslVTPppAuthChap	Integer32
	cdslVTPppAuthMSChap	Integer32
	cdslVTPppAuthPap	Integer32
	cdslVTPppChapHost	DisplayString
	cdslVTPppChapPassword	DisplayString
	cdslVTPppChapEncrypType	TruthValue
	cdslVTPppChapRefuse	INTEGER
	cdslVTPppChapWaitPeer	TruthValue
	cdslVTPppPapUserName	DisplayString
	cdslVTPppPapPassword	DisplayString
	cdslVTPppPapEncrypType	TruthValue
	cdslVTPppUseTacacs	INTEGER
	cdslVTRowStatus	RowStatus

CdslLocalIpAddrPoolNumberEntry
SEQUENCE
	cdslMaxLocalIpAddrPools	Unsigned32
	cdslLocalIpAddrPools	Gauge32

CdslLocalIpAddrPoolEntry
SEQUENCE
	cdslLocalIpAddrPoolName	DisplayString
	cdslLocalIpAddrPoolFreeAddresses	Unsigned32
	cdslLocalIpAddrPoolInUseAddresses	Unsigned32

CdslLocalIpAddrRangeEntry
SEQUENCE
	cdslLocalIpAddrRangeLowAddr	IpAddress
	cdslLocalIpAddrRangeHighAddr	IpAddress
	cdslLocalIpAddrRangeRowStatus	RowStatus

CdslPppOverAtmPvcNumberEntry
SEQUENCE
	cdslPppOverAtmPvcs	Gauge32

CdslAtmPvcEntry
SEQUENCE
	cdslAtmPvcVpi	Integer32
	cdslAtmPvcVci	Integer32
	cdslAtmPvcName	DisplayString
	cdslAtmPvcSubIfNumber	Integer32
	cdslAtmPvcClass	DisplayString
	cdslAtmPvcQosType	INTEGER
	cdslAtmPvcAbrPCR	Unsigned32
	cdslAtmPvcAbrMCR	Unsigned32
	cdslAtmPvcAbrIORIF	Unsigned32
	cdslAtmPvcAbrIORDF	Unsigned32
	cdslAtmPvcBroadcast	INTEGER
	cdslAtmPvcEncapsulation	INTEGER
	cdslAtmPvcMuxLinkType	INTEGER
	cdslAtmPvcVirtualTemplate	Integer32
	cdslAtmPvcILMIManage	INTEGER
	cdslAtmPvcInarp	Unsigned32
	cdslAtmPvcOamRetryUpCount	Unsigned32
	cdslAtmPvcOamRetryDownCount	Unsigned32
	cdslAtmPvcOamPvcManaged	INTEGER
	cdslAtmPvcOamPvcLF	Unsigned32
	cdslAtmPvcProtocolIpBC	TruthValue
	cdslAtmPvcProtocolIpxBC	TruthValue
	cdslAtmPvcUbrPCR	Unsigned32
	cdslAtmPvcUbrPlusPCR	Unsigned32
	cdslAtmPvcUbrPlusMCR	Unsigned32
	cdslAtmPvcVbrNrtPCR	Unsigned32
	cdslAtmPvcVbrNrtSCR	Unsigned32
	cdslAtmPvcRowStatus	RowStatus

CdslVcClassNumberEntry
SEQUENCE
	cdslMaxVcClasses	Unsigned32
	cdslVcClasses	Gauge32

CdslVcClassEntry
SEQUENCE
	cdslVcClassName	DisplayString
	cdslVcClassType	INTEGER
	cdslVcClassQosType	INTEGER
	cdslVcClassAbrPCR	Integer32
	cdslVcClassAbrMcr	Integer32
	cdslVcClassAbrIORIF	Integer32
	cdslVcClassAbrIORDF	Integer32
	cdslVcClassBroadcast	INTEGER
	cdslVcClassEncapsulation	INTEGER
	cdslVcClassMuxLinkType	INTEGER
	cdslVcClassVirtualTemplate	Integer32
	cdslVcClassIdleTimeout	Integer32
	cdslVcClassIdleMTR	Integer32
	cdslVcClassILMIManage	INTEGER
	cdslVcClassInarp	Integer32
	cdslVcClassOamRetryUpCount	Integer32
	cdslVcClassOamRetryDownCount	Integer32
	cdslVcClassOamPvcManaged	INTEGER
	cdslVcClassOamPvcLF	Integer32
	cdslVcClassOamSvcManaged	INTEGER
	cdslVcClassOamSvcLF	Integer32
	cdslVcClassProtocolIpBC	TruthValue
	cdslVcClassProtocolIpxBC	TruthValue
	cdslVcClassTransmitPriority	Integer32
	cdslVcClassUbrPCR	Integer32
	cdslVcClassUbrInputPCR	Integer32
	cdslVcClassUbrPlusPCR	Integer32
	cdslVcClassUbrPlusMCR	Integer32
	cdslVcClassUbrPlusInputPCR	Integer32
	cdslVcClassUbrPlusInputMCR	Integer32
	cdslVcClassVbrNrtPCR	Integer32
	cdslVcClassVbrNrtSCR	Integer32
	cdslVcClassVbrNrtInputBP	Integer32
	cdslVcClassVbrNrtInputPCR	Integer32
	cdslVcClassVbrNrtInputSCR	Integer32
	cdslVcClassVbrNrtInputMBS	Integer32
	cdslVcClassRowStatus	RowStatus

Defined Values

ciscoDslProvisionMIB		1.3.6.1.4.1.9.10.30
Cisco DSL (Digital Subscriber Line) Provision MIB Module. It is used to create subscriber PPP over ATM sessions and related tasks.
MODULE-IDENTITY

ciscoDslProvMIBObjects		1.3.6.1.4.1.9.10.30.1
OBJECT IDENTIFIER

cdslNrpSlot		1.3.6.1.4.1.9.10.30.1.1
OBJECT IDENTIFIER

cdslVirtualTemplate		1.3.6.1.4.1.9.10.30.1.2
OBJECT IDENTIFIER

cdslLocalIpAddrPool		1.3.6.1.4.1.9.10.30.1.3
OBJECT IDENTIFIER

cdslAtmPvc		1.3.6.1.4.1.9.10.30.1.4
OBJECT IDENTIFIER

cdslVcClass		1.3.6.1.4.1.9.10.30.1.5
OBJECT IDENTIFIER

cdslMaxNrps		1.3.6.1.4.1.9.10.30.1.1.1
Maximum number of the node routing processors (NRP) allowed in the system.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

cdslNrpNumber		1.3.6.1.4.1.9.10.30.1.1.2
The number of NRPs that are present in this system.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32	0..4294967295

cdslNrpIpAddressTable		1.3.6.1.4.1.9.10.30.1.1.3
This table reflects the IP addresses of each NRP in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CdslNrpIpAddressEntry

cdslNrpIpAddressEntry		1.3.6.1.4.1.9.10.30.1.1.3.1
These entries are used to store the IP Addresses of NRP cards that are inserted in the indexed slot. The IP addresses are used to access these cards.
Status: current	Access: not-accessible
OBJECT-TYPE
	CdslNrpIpAddressEntry

cdslNrpSlotIndex		1.3.6.1.4.1.9.10.30.1.1.3.1.1
The object specifies the identifier of a slot containing a NRP.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

cdslNrpIpAddress		1.3.6.1.4.1.9.10.30.1.1.3.1.2
The object specifies the IP addresses associated with the NRP contained in the slot identified by cdslNrpSlotIndex.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

cdslVirtualTemplateNumberTable		1.3.6.1.4.1.9.10.30.1.2.1
This table reflects the number of virtual template that are presently set up in each NRP. A virtual template interface is a logical entity a configuration for a serial-interface but not tied to a physical interface - thatcan be applied dynamically as needed.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CdslVirtualTemplateNumberEntry

cdslVirtualTemplateNumberEntry		1.3.6.1.4.1.9.10.30.1.2.1.1
Entries are read only.
Status: current	Access: not-accessible
OBJECT-TYPE
	CdslVirtualTemplateNumberEntry

cdslMaxVirtualTemplates		1.3.6.1.4.1.9.10.30.1.2.1.1.1
The object specifies the maximum number of virtual templates allowed in one single NRP.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

cdslVirtualTemplates		1.3.6.1.4.1.9.10.30.1.2.1.1.2
This object indicates the number of virtual templates presently set up in each NRP identified by cdslNrpSlotIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32	0..4294967295

cdslVirtualTemplateTable		1.3.6.1.4.1.9.10.30.1.2.2
This table includes the virtual templates in the NRP identified by cNrpSlotIndex. Though a virtual template is often called a virtual template interface, it is not reflected in the ifTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CdslVirtualTemplateEntry

cdslVirtualTemplateEntry		1.3.6.1.4.1.9.10.30.1.2.2.1
User may create a new entry or delete an existing entry. Entries may be created without explicitly setting cdslVTRowStatus. While the row status is 'active', objects having read-create access can be changed.
Status: current	Access: not-accessible
OBJECT-TYPE
	CdslVirtualTemplateEntry

cdslVTIndex		1.3.6.1.4.1.9.10.30.1.2.2.1.1
This object represents an arbitrary index used to identify the virtual template entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

cdslVTIpAddressMethod		1.3.6.1.4.1.9.10.30.1.2.2.1.2
This object indicates how an IP address is obtained to be associated with this virtual template. The actual parameters of these methods are indicated by the objects defined after. none -- means no IP address associated. ipAddress -- means an explicit IP address and mask. interfaceIp -- uses the IP address of an interface if it has one. negotiate -- obtains IP address from a pre-configured DHCP server. In the set operation, only the parameter corresponding to this object is considered. All other parameters are ignored and forgotten.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), ipAddress(1), interfaceIp(2), negotiate(3)

cdslVTIpAddress		1.3.6.1.4.1.9.10.30.1.2.2.1.3
This object specifies the IP address associated with this virtual template entry. This object is only valid when cdslVTIpAddressMethod is 'ipAddress'. To set the value correctly, this object shall be set in the same packet as cdslVTIpAddressMethod.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

cdslVTIpAddressMask		1.3.6.1.4.1.9.10.30.1.2.2.1.4
This object specifies the IP address mask. This object is only valid when cdslVTIpAddressMethod is 'ipAddress'. To set the value correctly, this object shall be set in the same packet as cdslVTIpAddressMethod.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

cdslVTIpIfIndex		1.3.6.1.4.1.9.10.30.1.2.2.1.5
This object specifies the ifIndex of the interface, whose IP address will be used for the virtual template entry. Any interface with an IP address in the routing processor can be selected. This object is only valid when cdslVTIpAddressMethod is 'interfaceIp'. To set the value correctly, this object shall be set in the same packet as cdslVTIpAddressMethod.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

cdslVTPeerIpAddressMethod		1.3.6.1.4.1.9.10.30.1.2.2.1.6
This object indicates how an IP address is obtained when a peer requesting one. The actual parameters of these methods are indicated by the objects defined after. none -- means no IP address associated. negotiate -- obtains IP address from a pre-configured DHCP server. ipAddressPool -- obtains IP address from an ip address pool specified by cdslVTPeerIpAddrPool to be defined. In the set operation, only the parameter corresponding to the value of this object is considered. All other parameters are ignored and forgotten.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), negotiate(1), ipAddressPool(2)

cdslVTPeerIpAddrPool		1.3.6.1.4.1.9.10.30.1.2.2.1.7
This object is used to specify peer default local IP address pool name. This object is only valid when cdslVTPeerIpAddressMethod is 'ipAddressPool'. To set the value correctly, this object shall be set in the same packet as cdslVTPeerIpAddressMethod. If set this object to a pool name that does not correspond to any entry in the cdslLocalIpAddrPoolTable, then the global IP address mechanism shall be applied. So to use the global IP address mechanism, one should set this object to a non-existent cdslLocalIpAddrPoolName or an empty string.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

cdslVTPppAuthChap		1.3.6.1.4.1.9.10.30.1.2.2.1.8
This object is used to specify to use Challenge Handshake Authentication Protocol (CHAP) authentication method and the order it is used. The value zero indicates that CHAP is not used. See the description of object cdslVTPppAuthPap for the meaning of non-zero value.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cdslVTPppAuthMSChap		1.3.6.1.4.1.9.10.30.1.2.2.1.9
This object is used to specify the use of Microsoft's CHAP (MSCHAP) authentication method and the order it is used. The value zero indicates that MSCHAP is not used. See the description of object cdslVTPppAuthPap for the meaning of non-zero value.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cdslVTPppAuthPap		1.3.6.1.4.1.9.10.30.1.2.2.1.10
This object is used to specify whether to use Password Authentication Protocol (PAP) authentication method and the order it is used. This object is one of multiple objects used to specify authentication methods. The other authentication method objects are cdslVTPppAuthChap and cdslVTPppAuthMSChap. A non-zero value for any of these authentication method objects indicates that its associated authentication method is to be employed. The value of these objects indicates the order in which their respective methods should be applied to the process of authenticating users. The lowest non-zero valued authentication method object is used first. If it fails, the second lowest is applied. If all methods fail, the user is rejected. If multiple objects are set to the same value, then the order of the corresponding methods will be adjusted in the order of CHAP, MSCHAP and PAP. Each time one of these auth method value is set, all the auth method object values will be re-assigned to reflect the order change and the values will be in an incremental order started from one. So the return value(s) of a snmpget request for these objects may be different from what they are set. However the order is preserved.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

cdslVTPppChapHost		1.3.6.1.4.1.9.10.30.1.2.2.1.11
This object is used to specify the PPP CHAP host name.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

cdslVTPppChapPassword		1.3.6.1.4.1.9.10.30.1.2.2.1.12
This object is used to specify the PPP CHAP password.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..25)

cdslVTPppChapEncrypType		1.3.6.1.4.1.9.10.30.1.2.2.1.13
This object is used to specify whether to encrypt the PPP CHAP password. Only effective when cdslVTPppChapPassword is non-empty.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cdslVTPppChapRefuse		1.3.6.1.4.1.9.10.30.1.2.2.1.14
The object is used to refuse CHAP authentication from peers requesting it. To disable this function set the value to no. RefuseCallinOnly indicating the system to refuse to answer CHAP authentication challenges received from the peer, but will still require the peer to answer any CHAP challenges this system sends.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(1), refuse(2), refuseCallinOnly(3)

cdslVTPppChapWaitPeer		1.3.6.1.4.1.9.10.30.1.2.2.1.15
This object is used to specify that the system will not authenticate to a peer requesting CHAP authentication until after the peer has authenticated to this system. To disable this function, set this object to 'false'. That is the system will handle the peer authentication requesting even if a peer has not authenticate itself yet.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cdslVTPppPapUserName		1.3.6.1.4.1.9.10.30.1.2.2.1.16
This object is used to specify the PPP PAP user name that will be sent to a peer device. Please refer to the description of cdslVTPppPassword to see the interaction.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

cdslVTPppPapPassword		1.3.6.1.4.1.9.10.30.1.2.2.1.17
This object is used to specify the PPP PAP authentication password. The system only utilizes the user name and password when both cdslVTPppUserName and cdslVTPppPassword are non-empty strings. To enforce this the following mechanism is applied. When both are empty strings, set any single one into non-empty string would automatically set the other into the same string. When set any into empty string, the other object would be set to empty string too automatically.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

cdslVTPppPapEncrypType		1.3.6.1.4.1.9.10.30.1.2.2.1.18
This object is used to specify whether to encrypt the PAP password. Only effective when cdslVTPppPapPassword is non-empty.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cdslVTPppUseTacacs		1.3.6.1.4.1.9.10.30.1.2.2.1.19
This object is used to specify whether to enable TACACS for PPP authentication. SingleLine means yes and plus to accept username and password in the username field that is in single line.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(1), yes(2), singleLine(3)

cdslVTRowStatus		1.3.6.1.4.1.9.10.30.1.2.2.1.20
This object is used to create a new row or modify or delete an existing row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

cdslLocalIpAddrPoolNumberTable		1.3.6.1.4.1.9.10.30.1.3.1
This table indicates the number of IP address pools that are presently set up in each NRP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CdslLocalIpAddrPoolNumberEntry

cdslLocalIpAddrPoolNumberEntry		1.3.6.1.4.1.9.10.30.1.3.1.1
Entries are read only.
Status: current	Access: not-accessible
OBJECT-TYPE
	CdslLocalIpAddrPoolNumberEntry

cdslMaxLocalIpAddrPools		1.3.6.1.4.1.9.10.30.1.3.1.1.1
Maximum number of local IP address pools allowed in a NRP.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

cdslLocalIpAddrPools		1.3.6.1.4.1.9.10.30.1.3.1.1.2
The number of local IP address pools presently set up.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32	0..4294967295

cdslLocalIpAddrPoolTable		1.3.6.1.4.1.9.10.30.1.3.2
This table defines the IP local address pool. An IP address pool may have a single entry in the table. The ranges of a pool are represented in the cdslLocalIPAddrRangeTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CdslLocalIpAddrPoolEntry

cdslLocalIpAddrPoolEntry		1.3.6.1.4.1.9.10.30.1.3.2.1
This list contains IP pool entry. The entry is read-only. The creation or the deletion of an entry will be a by-product of the entry in the cdslLocalIPAddrRangeTable. When an entry is created and activated in that table, an entry in this table will come into existance if it is not already so. When an entry is deleted in that table, if there is no other entry existing in that table with the same cdslNrpSlotIndex and cdslLocalIpAddrPoolName, the netry in this table with the same indices will diappear from the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	CdslLocalIpAddrPoolEntry

cdslLocalIpAddrPoolName		1.3.6.1.4.1.9.10.30.1.3.2.1.1
A unique and non-empty string for the pool. The name can not be modified once created.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..32)

cdslLocalIpAddrPoolFreeAddresses		1.3.6.1.4.1.9.10.30.1.3.2.1.2
The number of IP addresses still available for use in the pool. Please notice that the number is for the whole pool, not for the individual range.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

cdslLocalIpAddrPoolInUseAddresses		1.3.6.1.4.1.9.10.30.1.3.2.1.3
The number of addresses currently in use in the pool. Please notice that the number is for the whole pool, not for the individual range.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

cdslLocalIpAddrRangeTable		1.3.6.1.4.1.9.10.30.1.3.3
This table defines the IP local address pool ranges. An IP address pool may have a single entry or multiple entries in the table, since an IP address pool can have multiple dis-continuous ranges. Each range will have a separate entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CdslLocalIpAddrRangeEntry

cdslLocalIpAddrRangeEntry		1.3.6.1.4.1.9.10.30.1.3.3.1
This list contains IP pool range entry. User may create a new entry or delete an existing entry. When creating an entry, after its activation, an entry in the cdslLocalIpAddrPoolTable will exist if it is not already so. When destroying an entry, if the range is the only range in the pool, the range entry will be destroyed and the pool entry will disappear from the cdslLocalIpAddrPoolTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	CdslLocalIpAddrRangeEntry

cdslLocalIpAddrRangeLowAddr		1.3.6.1.4.1.9.10.30.1.3.3.1.1
The low range of this IP address pool range. This must be lower than the pool's high range.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

cdslLocalIpAddrRangeHighAddr		1.3.6.1.4.1.9.10.30.1.3.3.1.2
The high range of this IP address pool range. This must be higher than the pool's low range.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

cdslLocalIpAddrRangeRowStatus		1.3.6.1.4.1.9.10.30.1.3.3.1.3
This object is used to create a new row or delete an existing row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

cdslPppOverAtmPvcNumberTable		1.3.6.1.4.1.9.10.30.1.4.1
This table reflects the number of PVCs of PPP encapsulation presently set up in each NRP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CdslPppOverAtmPvcNumberEntry

cdslPppOverAtmPvcNumberEntry		1.3.6.1.4.1.9.10.30.1.4.1.1
Each entry represents the responding NRP.
Status: current	Access: not-accessible
OBJECT-TYPE
	CdslPppOverAtmPvcNumberEntry

cdslPppOverAtmPvcs		1.3.6.1.4.1.9.10.30.1.4.1.1.1
The number of atm pvcs that are presently set up with PPP encapsulation. The number of all atm PVCs and the maximum number of PVCs are provided by AToM Mib.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32	0..4294967295

cdslAtmPvcTable		1.3.6.1.4.1.9.10.30.1.4.2
This table includes configuration parameters for ATM PVCs with PPP encapsulation. The vc-mode ATM PVC management approach is used as the PVC creating method, which greatly simplifies configuration by using of vc-class. The PVCs which were created using atm pvc cli commands can only be read or deleted from snmp. In case of reading, only the values of vpi, vci, sub-interface number, encapsulation, virtual template number and row status are meaningful. When trying to set any object of these PVCs, a GEN_ERROR returns except for the row status object. To indicate a PVC is created with old pvc syntax, the value of cdslAtmPvcClass will be set into '!'.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CdslAtmPvcEntry

cdslAtmPvcEntry		1.3.6.1.4.1.9.10.30.1.4.2.1
The IfIndex by which the table is indexed, is the ATM interface index in which the PVC is created. The only object that is allowed to change the value while the row status is 'active' is cdslAtmPvcClass. Please refer to the description of cdslAtmPvcRowStatus for more information.
Status: current	Access: not-accessible
OBJECT-TYPE
	CdslAtmPvcEntry

cdslAtmPvcVpi		1.3.6.1.4.1.9.10.30.1.4.2.1.1
The virtual path identifier of the PVC. Please note that it is routing processor's VPI number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..65535

cdslAtmPvcVci		1.3.6.1.4.1.9.10.30.1.4.2.1.2
The virtual channel identifier of the PVC. Please note that it is routing processor's VCI number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..65535

cdslAtmPvcName		1.3.6.1.4.1.9.10.30.1.4.2.1.3
This object can be used to identify the PVC. Unique name for each PVC is desired if assigned.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

cdslAtmPvcSubIfNumber		1.3.6.1.4.1.9.10.30.1.4.2.1.4
This object indicates the ios sub-interface number if this PVC belongs to an atm sub-interface. Once the pvc exists, the value can not be modified. If the PVC is created under the ATM interface level and not a subinterface level, the object shall be zero.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

cdslAtmPvcClass		1.3.6.1.4.1.9.10.30.1.4.2.1.5
This object indicates the vc-class to inherit when the named vc-class exists. If the object is to set into an empty string, the default value 'default-vc-class' will be used. If the 'default-vc-class' class does exist, it will be created and the encapsulation is set to aal5ciscoppp and the virtual template number is set to the largest virtual template number allowed. If the specified virtual template does not exist, it will be created with no specific configuration. If the specified vc-class does not exist, a new vc-class will be created in the same way as the default-vc-class is. If the specified vc-class exists and its encapsulation is not 'aal5mux' or 'aal5ciscoppp', an error will be returned.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

cdslAtmPvcQosType		1.3.6.1.4.1.9.10.30.1.4.2.1.6
Quality of Service type of this PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ubrDefault(0), cbr(1), ubr(2), ubrPlus(3), vbrRt(4), vbrNrt(5), abr(6), max(7)

cdslAtmPvcAbrPCR		1.3.6.1.4.1.9.10.30.1.4.2.1.7
Availabe bit rate (Abr) peak cell rate(PCR) of this PVC.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

cdslAtmPvcAbrMCR		1.3.6.1.4.1.9.10.30.1.4.2.1.8
Abr Minimum Guaranteed Cell Rate(MCR) of this PVC.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..1

cdslAtmPvcAbrIORIF		1.3.6.1.4.1.9.10.30.1.4.2.1.9
Abr inverse of rate increase factor (1/rif) of this PVC.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

cdslAtmPvcAbrIORDF		1.3.6.1.4.1.9.10.30.1.4.2.1.10
Abr inverse of rate decrease factor (1/rdf) of this PVC.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

cdslAtmPvcBroadcast		1.3.6.1.4.1.9.10.30.1.4.2.1.11
This object indicates whether to allow broadcast or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	false(0), true(1), unknown(2)

cdslAtmPvcEncapsulation		1.3.6.1.4.1.9.10.30.1.4.2.1.12
This object indicates encapsulation method of this PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	default(0), aal5snap(1), aal5mux(2), aal5nlpid(3), aal34smds(4), aal5ilmi(5), aal5qsaal(6), aal5ciscoppp(7)

cdslAtmPvcMuxLinkType		1.3.6.1.4.1.9.10.30.1.4.2.1.13
This object can be used to This object is used to specify the link type if the encapsulation is aal5mux. 1 -- ip and 2 -- ppp.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ip(1), ppp(2)

cdslAtmPvcVirtualTemplate		1.3.6.1.4.1.9.10.30.1.4.2.1.14
The virtual template number configured for the PVC.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

cdslAtmPvcILMIManage		1.3.6.1.4.1.9.10.30.1.4.2.1.15
This object indicates whether to ilmi manage or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	false(0), true(1), unknown(2)

cdslAtmPvcInarp		1.3.6.1.4.1.9.10.30.1.4.2.1.16
This object indicates the InARP Frequency in minutes (Only meaningful in aal5snap encapsulation).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..60

cdslAtmPvcOamRetryUpCount		1.3.6.1.4.1.9.10.30.1.4.2.1.17
This object indicates the OAM retry count before declaring a VC is up.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..600

cdslAtmPvcOamRetryDownCount		1.3.6.1.4.1.9.10.30.1.4.2.1.18
This object indicates the OAM retry count before declaring a VC is down.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..600

cdslAtmPvcOamPvcManaged		1.3.6.1.4.1.9.10.30.1.4.2.1.19
This object indicates whether to enable VC management on OAM in this PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	false(0), true(1), unknown(2)

cdslAtmPvcOamPvcLF		1.3.6.1.4.1.9.10.30.1.4.2.1.20
This object indicates the OAM loopback frequency(seconds) for this PVC.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..600

cdslAtmPvcProtocolIpBC		1.3.6.1.4.1.9.10.30.1.4.2.1.21
Pseudo-broadcast on the protocol IP inarp connections or not (Only meaningful in aal5snap encapsulation).
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

cdslAtmPvcProtocolIpxBC		1.3.6.1.4.1.9.10.30.1.4.2.1.22
This object indicates whether to allow Pseudo-broadcast on the protocol IPX inarp connections or not (Only meaningful in aal5snap encapsulation).
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

cdslAtmPvcUbrPCR		1.3.6.1.4.1.9.10.30.1.4.2.1.23
This object indicates the Ubr Peak Cell Rate.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..155000

cdslAtmPvcUbrPlusPCR		1.3.6.1.4.1.9.10.30.1.4.2.1.24
This object indicates the Ubr+ Peak Cell Rate.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..155000

cdslAtmPvcUbrPlusMCR		1.3.6.1.4.1.9.10.30.1.4.2.1.25
This object indicates the Ubr+ Minimum Guaranteed Cell Rate.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..1

cdslAtmPvcVbrNrtPCR		1.3.6.1.4.1.9.10.30.1.4.2.1.26
This object indicates the Vbr-Nrt Peak Cell Rate.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..155000

cdslAtmPvcVbrNrtSCR		1.3.6.1.4.1.9.10.30.1.4.2.1.27
This object indicates the Vbr-Nrt Sustainable Cell Rate.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..1

cdslAtmPvcRowStatus		1.3.6.1.4.1.9.10.30.1.4.2.1.28
This object is used to create a new row or modify or delete an existing row in this table. When the row is created, but the minimun set of parameters is not all set, the status is 'notReady'. There is no PVC corresponding to it. The minimum set of parameters required to activate an entry is cdslAtmPvcSubIfNumber.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

cdslVcClassNumberTable		1.3.6.1.4.1.9.10.30.1.5.1
This table reflects the number of VC classes that are presently set up in each NRP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CdslVcClassNumberEntry

cdslVcClassNumberEntry		1.3.6.1.4.1.9.10.30.1.5.1.1
Entries are read only.
Status: current	Access: not-accessible
OBJECT-TYPE
	CdslVcClassNumberEntry

cdslMaxVcClasses		1.3.6.1.4.1.9.10.30.1.5.1.1.1
This object indicates the maximum number of VC classes allowed.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

cdslVcClasses		1.3.6.1.4.1.9.10.30.1.5.1.1.2
This object indicates the number of VC classes presently set in each NRP identified by cdslNrpSlotIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32	0..4294967295

cdslVcClassTable		1.3.6.1.4.1.9.10.30.1.5.2
The entries in this table are vc-classes with at least one parameter configured. In other words, empty classes (with name only) will not be present in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CdslVcClassEntry

cdslVcClassEntry		1.3.6.1.4.1.9.10.30.1.5.2.1
The VC Class entry is read-create. Each entry represents a VC class.
Status: current	Access: not-accessible
OBJECT-TYPE
	CdslVcClassEntry

cdslVcClassName		1.3.6.1.4.1.9.10.30.1.5.2.1.1
This object is used to identify the vc class.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..32)

cdslVcClassType		1.3.6.1.4.1.9.10.30.1.5.2.1.2
This object indicates the type of the vc class. Atm is for Asynchronous transfer mode and funi for frame user network interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	atm(1), funi(2)

cdslVcClassQosType		1.3.6.1.4.1.9.10.30.1.5.2.1.3
This object specifies the QOS type of the vc class.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ubrDefault(0), cbr(1), ubr(2), ubrPlus(3), vbrRt(4), vbrNrt(5), abr(6), max(7)

cdslVcClassAbrPCR		1.3.6.1.4.1.9.10.30.1.5.2.1.4
This object specifies Abr Peak Cell Rate.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	56..155000

cdslVcClassAbrMcr		1.3.6.1.4.1.9.10.30.1.5.2.1.5
This object specifies Minimum Guaranteed Cell Rate. It shall be smaller than cdslVcClassAbrPCR.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..155000

cdslVcClassAbrIORIF		1.3.6.1.4.1.9.10.30.1.5.2.1.6
This object specifies Abr inverse of rate increase factor (1/rif) to the power of two. Note that the actual value in the system is the power of two of this object. That is, for example, a value 5 of this object means 2**5 = 32 in the system for AbrIORIF. Range (0..15) to the power of two is the range (1..32768).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..15

cdslVcClassAbrIORDF		1.3.6.1.4.1.9.10.30.1.5.2.1.7
Abr inverse of rate decrease factor (1/rdf) to the power of two. Note that the actual value is the power of two of this object. For example, value 5 of this object means 2**5 = 32. Range (0..15) to the power of two is the range (1..32768).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..15

cdslVcClassBroadcast		1.3.6.1.4.1.9.10.30.1.5.2.1.8
This object indicates whether to allow broadcast or not. When set the value, do not use unknown.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	false(0), true(1), unknown(2)

cdslVcClassEncapsulation		1.3.6.1.4.1.9.10.30.1.5.2.1.9
This object specifies encapsulation method.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	default(0), aal5snap(1), aal5mux(2), aal5nlpid(3), aal34smds(4), aal5ilmi(5), aal5qsaal(6), aal5ciscoppp(7)

cdslVcClassMuxLinkType		1.3.6.1.4.1.9.10.30.1.5.2.1.10
This object is used to specify the link type if the encapsulation is aal5mux. 1 for IP and 2 for PPP.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ip(1), ppp(2)

cdslVcClassVirtualTemplate		1.3.6.1.4.1.9.10.30.1.5.2.1.11
The virtual template number. Value zero means not configured.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

cdslVcClassIdleTimeout		1.3.6.1.4.1.9.10.30.1.5.2.1.12
This object specifies idle timeout.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2000000

cdslVcClassIdleMTR		1.3.6.1.4.1.9.10.30.1.5.2.1.13
This object specifies the minimum traffic rate to keep the connection.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..155000

cdslVcClassILMIManage		1.3.6.1.4.1.9.10.30.1.5.2.1.14
This object specifies whether to allow ilmi manage or not. When set the value, do not use unknown.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	false(0), true(1), unknown(2)

cdslVcClassInarp		1.3.6.1.4.1.9.10.30.1.5.2.1.15
This object specifies InARP Frequency in minutes.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..60

cdslVcClassOamRetryUpCount		1.3.6.1.4.1.9.10.30.1.5.2.1.16
OAM retry count before declaring a VC is up
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..600

cdslVcClassOamRetryDownCount		1.3.6.1.4.1.9.10.30.1.5.2.1.17
OAM retry count before declaring a VC is down
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..600

cdslVcClassOamPvcManaged		1.3.6.1.4.1.9.10.30.1.5.2.1.18
This object specifies whether to enable VC management on OAM in a PVC. When set the value, do not use unknown.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	false(0), true(1), unknown(2)

cdslVcClassOamPvcLF		1.3.6.1.4.1.9.10.30.1.5.2.1.19
This object specifies the OAM loopback frequency.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..600

cdslVcClassOamSvcManaged		1.3.6.1.4.1.9.10.30.1.5.2.1.20
This object specifies whether to enable VC management on OAM on SVC SVC. When set the value, do not use unknown.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	false(0), true(1), unknown(2)

cdslVcClassOamSvcLF		1.3.6.1.4.1.9.10.30.1.5.2.1.21
This object specifies the OAM loopback frequency for SVC
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..600

cdslVcClassProtocolIpBC		1.3.6.1.4.1.9.10.30.1.5.2.1.22
This object specifies whether to allow the pseudo-broadcast on the protocol IP inarp connections or not.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cdslVcClassProtocolIpxBC		1.3.6.1.4.1.9.10.30.1.5.2.1.23
This object specifies whether to allow the pseudo-broadcast on the protocol IPX inarp connections or not.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

cdslVcClassTransmitPriority		1.3.6.1.4.1.9.10.30.1.5.2.1.24
This object specifies the transmit priority.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

cdslVcClassUbrPCR		1.3.6.1.4.1.9.10.30.1.5.2.1.25
This object specifies the Ubr Peak Cell Rate.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..155000

cdslVcClassUbrInputPCR		1.3.6.1.4.1.9.10.30.1.5.2.1.26
This object specifies the Ubr Input Peak Cell Rate.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..155000

cdslVcClassUbrPlusPCR		1.3.6.1.4.1.9.10.30.1.5.2.1.27
This object specifies the Ubr+ Peak Cell Rate.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..155000

cdslVcClassUbrPlusMCR		1.3.6.1.4.1.9.10.30.1.5.2.1.28
This object specifies the Ubr+ Minimum Guaranteed Cell Rate. It shall be smaller than cdslVcClassUbrPlusPCR.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..155000

cdslVcClassUbrPlusInputPCR		1.3.6.1.4.1.9.10.30.1.5.2.1.29
This object specifies the Ubr+ Input Peak Cell Rate.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..155000

cdslVcClassUbrPlusInputMCR		1.3.6.1.4.1.9.10.30.1.5.2.1.30
This object specifies the Ubr+ Input Minimum Cell Rate. It shall be smaller than cdslVcClassUbrPlusInputPCR.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..155000

cdslVcClassVbrNrtPCR		1.3.6.1.4.1.9.10.30.1.5.2.1.31
This object specifies the Vbr-Nrt Peak Cell Rate.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..155000

cdslVcClassVbrNrtSCR		1.3.6.1.4.1.9.10.30.1.5.2.1.32
This object specifies the Vbr-Nrt Sustainable Cell Rate. It shall be smaller than cdslVcClassVbrNrtPCR.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..1

cdslVcClassVbrNrtInputBP		1.3.6.1.4.1.9.10.30.1.5.2.1.33
This object specifies the Vbr-Nrt Input Burst Parameter: rounded on AIP to the nearest 32, used as is on NPM.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65536

cdslVcClassVbrNrtInputPCR		1.3.6.1.4.1.9.10.30.1.5.2.1.34
This object specifies the Vbr-Nrt Input Peak Cell Rate.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..155000

cdslVcClassVbrNrtInputSCR		1.3.6.1.4.1.9.10.30.1.5.2.1.35
This object specifies the Vbr-Nrt Input Sustainable Cell Rate. It shall be smaller than cdslVcClassVbrNrtInputPCR.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..1

cdslVcClassVbrNrtInputMBS		1.3.6.1.4.1.9.10.30.1.5.2.1.36
This object specifies the Input Maximum Burst Size.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65536

cdslVcClassRowStatus		1.3.6.1.4.1.9.10.30.1.5.2.1.37
This object is used to create a new row or modify or delete an existing row in this table. The return value of this object is always 'active', if the row exists. To delete the row, set the value to 'destroy'. When creating a new row, 'createAndGo' is the default value and method even if 'createAndWait' is specified. The row and the VC class will be created. When deleting a vc class, if there is still reference to it, it is made invisibile. Otherwise, it is removed physically.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

ciscoDslProvMIBNotificationPrefix		1.3.6.1.4.1.9.10.30.2
OBJECT IDENTIFIER

ciscoDslProvMIBConformance		1.3.6.1.4.1.9.10.30.3
OBJECT IDENTIFIER

ciscoDslProvMIBCompliances		1.3.6.1.4.1.9.10.30.3.1
OBJECT IDENTIFIER

ciscoDslProvMIBGroups		1.3.6.1.4.1.9.10.30.3.2
OBJECT IDENTIFIER

ciscoDslProvMIBBasicCompliance		1.3.6.1.4.1.9.10.30.3.1.1
The compliance statement for entities which implement the Cisco DSL Provision Management MIB.
Status: current	Access: read-create
MODULE-COMPLIANCE

ciscoNrpSlotGroup		1.3.6.1.4.1.9.10.30.3.2.1
The DSL Provision NRP Slot Group.
Status: current	Access: read-create
OBJECT-GROUP

ciscoVirtualTemplateGroup		1.3.6.1.4.1.9.10.30.3.2.2
The DSL Provision Virtual Template Interface Group.
Status: current	Access: read-create
OBJECT-GROUP

ciscoIpPoolGroup		1.3.6.1.4.1.9.10.30.3.2.3
The DSL Provision IP Pool Group.
Status: current	Access: read-create
OBJECT-GROUP

ciscoDslPVCGroup		1.3.6.1.4.1.9.10.30.3.2.4
The DSL Provision PVC Group.
Status: current	Access: read-create
OBJECT-GROUP

ciscoVcClassGroup		1.3.6.1.4.1.9.10.30.3.2.5
The DSL Provision VC Class Group.
Status: current	Access: read-create
OBJECT-GROUP