CISCO-ENTITY-QFP-MIB

File: CISCO-ENTITY-QFP-MIB.mib (47189 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
ENTITY-MIB HCNUM-TC CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Gauge32
NOTIFICATION-TYPE Counter32 Counter64
Unsigned32 Integer32 MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP TEXTUAL-CONVENTION
DateAndTime TruthValue entPhysicalIndex
CounterBasedGauge64 ciscoMgmt

Defined Types

CiscoQfpPacketRate  
An estimate of throughput in units of packets per second. The CiscoQfpPacketRate type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value of Counter64. The Counter64 syntax is used for encoding rules.
TEXTUAL-CONVENTION    
  Counter64  

CiscoQfpBitRate  
An estimate of throughput in units of bits per second. The CiscoQfpBitRate type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value of Counter64. The Counter64 syntax is used for encoding rules.
TEXTUAL-CONVENTION    
  Counter64  

CiscoQfpTimeInterval  
An enumerated integer-value describing the available interval values for which the periodic statistics are to be collected. fiveSeconds (1) - Interval to collect last 5 seconds statistics oneMinute(2) - Interval to collect last 1 minute statistics fiveMinutes(3) - Interval to collect last 5 minutes statistics sixtyMinutes(4) - Interval to collect last 60 minutes statistics
TEXTUAL-CONVENTION    
  INTEGER fiveSeconds(1), oneMinute(2), fiveMinutes(3), sixtyMinutes(4)  

CiscoQfpMemoryResource  
An enumerated integer-value describing various memory resources used by the QFP. dram (1) - Dynamic Random Access Memory (DRAM) memory resource
TEXTUAL-CONVENTION    
  INTEGER dram(1)  

CeqfpSystemEntry  
SEQUENCE    
  ceqfpSystemTrafficDirection INTEGER
  ceqfpSystemState INTEGER
  ceqfpNumberSystemLoads Counter32
  ceqfpSystemLastLoadTime DateAndTime

CeqfpUtilizationEntry  
SEQUENCE    
  ceqfpUtilTimeInterval CiscoQfpTimeInterval
  ceqfpUtilInputPriorityPktRate CiscoQfpPacketRate
  ceqfpUtilInputPriorityBitRate CiscoQfpBitRate
  ceqfpUtilInputNonPriorityPktRate CiscoQfpPacketRate
  ceqfpUtilInputNonPriorityBitRate CiscoQfpBitRate
  ceqfpUtilInputTotalPktRate CiscoQfpPacketRate
  ceqfpUtilInputTotalBitRate CiscoQfpBitRate
  ceqfpUtilOutputPriorityPktRate CiscoQfpPacketRate
  ceqfpUtilOutputPriorityBitRate CiscoQfpBitRate
  ceqfpUtilOutputNonPriorityPktRate CiscoQfpPacketRate
  ceqfpUtilOutputNonPriorityBitRate CiscoQfpBitRate
  ceqfpUtilOutputTotalPktRate CiscoQfpPacketRate
  ceqfpUtilOutputTotalBitRate CiscoQfpBitRate
  ceqfpUtilProcessingLoad Gauge32

CeqfpMemoryResourceEntry  
SEQUENCE    
  ceqfpMemoryResType CiscoQfpMemoryResource
  ceqfpMemoryResTotal Gauge32
  ceqfpMemoryResInUse Gauge32
  ceqfpMemoryResFree Gauge32
  ceqfpMemoryResLowFreeWatermark Gauge32
  ceqfpMemoryResRisingThreshold Unsigned32
  ceqfpMemoryResFallingThreshold Unsigned32
  ceqfpMemoryResTotalOvrflw Gauge32
  ceqfpMemoryHCResTotal CounterBasedGauge64
  ceqfpMemoryResInUseOvrflw Gauge32
  ceqfpMemoryHCResInUse CounterBasedGauge64
  ceqfpMemoryResFreeOvrflw Gauge32
  ceqfpMemoryHCResFree CounterBasedGauge64
  ceqfpMemoryResLowFreeWatermarkOvrflw Gauge32
  ceqfpMemoryHCResLowFreeWatermark CounterBasedGauge64

CeqfpThroughputEntry  
SEQUENCE    
  ceqfpThroughputLicensedBW Counter64
  ceqfpThroughputLevel INTEGER
  ceqfpThroughputInterval Integer32
  ceqfpThroughputThreshold Integer32
  ceqfpThroughputAvgRate Counter64

Defined Values

ciscoEntityQfpMIB 1.3.6.1.4.1.9.9.715
This MIB module defines managed objects that facilitate the management of Quantum Flow Processors (QFP), which are listed in the ENTITY-MIB (RFC 4133) entPhysicalTable as an entPhysicalClass of 'cpu'. The Quantum Flow Processors (QFP) technology is an architecture family developed by Cisco, which has fully integrated and programmable networking chip set that controls different functions of a system such as packet forwarding. This module contains objects to monitor various QFP statistics such as system, utilization, memory, etc. The utilization statistics can be used for future capacity planning. The calculation of this statistics may vary by devices which host QFPs, hence the user must refer to the specific device document of interest for the exact method of calculation. The utilization statistics have the following terminology. o Input - Communication channel where packets arrive on the QFP. o Output - Communication channel where packets leave the QFP. o Priority - A classification applied to packets indicating they should be treated with greater urgency. o Non-Priority - A classification applied to packets indicating they should be treated with lesser urgency. o Processing Load - The percentage of time over some interval that the QFP has spent forwarding packets, relative to the total time spent both forwarding packets and being idle.
MODULE-IDENTITY    

ciscoEntityQfpMIBNotifs 1.3.6.1.4.1.9.9.715.0
OBJECT IDENTIFIER    

ciscoEntityQfpMIBObjects 1.3.6.1.4.1.9.9.715.1
OBJECT IDENTIFIER    

ciscoEntityQfpMIBConform 1.3.6.1.4.1.9.9.715.2
OBJECT IDENTIFIER    

ciscoEntityQfp 1.3.6.1.4.1.9.9.715.1.1
OBJECT IDENTIFIER    

ciscoEntityQfpNotif 1.3.6.1.4.1.9.9.715.1.2
OBJECT IDENTIFIER    

ceqfpSystemTable 1.3.6.1.4.1.9.9.715.1.1.1
This table maintains the QFP system information for each QFP physical entity. An agent creates a conceptual row to this table corresponding to a QFP physical entity upon detection of a physical entity supporting the QFP system information. An agent destroys a conceptual row from this table corresponding to a QFP physical entity upon removal of the QFP host physical entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CeqfpSystemEntry

ceqfpSystemEntry 1.3.6.1.4.1.9.9.715.1.1.1.1
A conceptual row in the ceqfpSystemTable. There is an entry in this table for each QFP entity, as defined by a value of entPhysicalIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  CeqfpSystemEntry  

ceqfpSystemTrafficDirection 1.3.6.1.4.1.9.9.715.1.1.1.1.1
This object represents the traffic direction that this QFP is assigned to process. The enumerated values are described below. none (1) - The QFP is not assigned to processes any traffic yet ingress (2) - The QFP processes inbound traffic egress (3) - The QFP processes outbound traffic both (4) - The QFP processes both inbound and outbound traffic
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), ingress(2), egress(3), both(4)  

ceqfpSystemState 1.3.6.1.4.1.9.9.715.1.1.1.1.2
This object represents the current QFP state. The enumerated values are described below. unknown (1) - The state of the QFP is unknown reset (2) - The QFP is reset init (3) - The QFP is being initialized active (4) - The QFP is active in a system with redundant QFP activeSolo (5) - The QFP is active and there is no redundant QFP in the system standby (6) - The QFP is standby in a redundant system. hotStandby (7) - The QFP is standby and synchronized with active, so that a switchover in this state will preserve state of the active. Stateful datapath features are synchronized between the active QFP and standby QFP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), reset(2), init(3), active(4), activeSolo(5), standby(6), hotStandby(7)  

ceqfpNumberSystemLoads 1.3.6.1.4.1.9.9.715.1.1.1.1.3
This object represents the number of times the QFP is loaded, since the QFP host is up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ceqfpSystemLastLoadTime 1.3.6.1.4.1.9.9.715.1.1.1.1.4
This object represents the QFP last load time.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

ceqfpFiveSecondUtilAlgo 1.3.6.1.4.1.9.9.715.1.1.2
This objects represents the method used to calculate 5 Second interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSample (2) - The value is calculated based on the last 5 second sampling period of utilization data.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), fiveSecSample(2)  

ceqfpOneMinuteUtilAlgo 1.3.6.1.4.1.9.9.715.1.1.3
This objects represents the method used to calculate 1 Minute interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSMA (2) - The value is calculated using Simple Moving Average of last 12 five seconds utilization data.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), fiveSecSMA(2)  

ceqfpFiveMinutesUtilAlgo 1.3.6.1.4.1.9.9.715.1.1.4
This objects represents the method used to calculate 5 Minutes interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSMA (2) - The value is calculated using Simple Moving Average of last 60 five seconds utilization data.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), fiveSecSMA(2)  

ceqfpSixtyMinutesUtilAlgo 1.3.6.1.4.1.9.9.715.1.1.5
This objects represents the method used to calculate 60 Minutes interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSMA (1) - The value is calculated using Simple Moving Average of last 720 five seconds utilization data.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), fiveSecSMA(2)  

ceqfpUtilizationTable 1.3.6.1.4.1.9.9.715.1.1.6
This table maintains the utilization statistics collected by each QFP physical entity at various time interval such as last 5 seconds, 1 minute, etc. An agent creates a conceptual row to this table corresponding to a QFP physical entity for a time interval upon detection of a physical entity supporting the utilization statistics for a time interval. The agent destroys a conceptual row from this table corresponding to a QFP physical entity for a time interval upon removal of the QFP host physical entity or it does not receive the utilization statistics update for a certain time period. The time period to wait before deleting an entry from this table would be the discretion of the supporting device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CeqfpUtilizationEntry

ceqfpUtilizationEntry 1.3.6.1.4.1.9.9.715.1.1.6.1
A conceptual row in the ceqfpUtilizationTable. There is an entry in this table for each QFP entity by a value of entPhysicalIndex and the supported time interval by a value of ceqfpUtilTimeInterval. The method of utilization data calculation for each interval period can be identified through the respective interval scalar objects. For example the utilizaiton data calculation method for 'fiveSecond' interval can be identified by ceqfpFiveSecondUtilAlgo.
Status: current Access: not-accessible
OBJECT-TYPE    
  CeqfpUtilizationEntry  

ceqfpUtilTimeInterval 1.3.6.1.4.1.9.9.715.1.1.6.1.1
This object identifies the time interval for which the utilization statistics being collected. The interval values can be 5 second, 1 minute, etc. as specified in the CiscoQfpTimeInterval.
Status: current Access: not-accessible
OBJECT-TYPE    
  CiscoQfpTimeInterval  

ceqfpUtilInputPriorityPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.2
This object represents the QFP input channel priority packet rate during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilInputPriorityBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.3
This object represents the QFP input channel priority bit rate during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilInputNonPriorityPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.4
This object represents the QFP input channel non-priority packet rate during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilInputNonPriorityBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.5
This object represents the QFP input channel non-priority bit rate during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilInputTotalPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.6
This object represents the QFP input channel total packet rate during this interval, which includes both priority and non-priority input packet rate.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilInputTotalBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.7
This object represents the QFP input channel total bit rate during this interval, which includes both priority and non-priority input bit rate.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilOutputPriorityPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.8
This object represents the QFP output channel priority packet rate during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilOutputPriorityBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.9
This object represents the QFP output channel priority bit rate during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilOutputNonPriorityPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.10
This object represents the QFP output channel non-priority packet rate during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilOutputNonPriorityBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.11
This object represents the QFP output channel non-priority bit rate during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilOutputTotalPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.12
This object represents the QFP output channel total packet rate during this interval, which includes both priority and non-priority output packet rate.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilOutputTotalBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.13
This object represents the QFP output channel total bit rate during this interval, which includes both priority and non-priority bit rate.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilProcessingLoad 1.3.6.1.4.1.9.9.715.1.1.6.1.14
This object represents the QFP processing load during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

ceqfpMemoryResourceTable 1.3.6.1.4.1.9.9.715.1.1.7
This table maintains the memory resources statistics for each QFP physical entity. An agent creates a conceptual row to this table corresponding to a QFP physical entity and its supported memory resource type upon detection of a physical entity supporting the memory resource statistics for a memory resource type. An agent destroys a conceptual row from this table corresponding to a QFP physical entity and its supported memory resource type upon removal of the QFP host physical entity or it does not receive memory resource statistics update for a certain time period. The time period to wait before deleting an entry from this table would be the discretion of the supporting device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CeqfpMemoryResourceEntry

ceqfpMemoryResourceEntry 1.3.6.1.4.1.9.9.715.1.1.7.1
A conceptual row in the ceqfpMemoryResourceTable. There is an entry in this table for each QFP entity by a value of entPhysicalIndex and the supported memory resource type by a value of ceqfpMemoryResType.
Status: current Access: not-accessible
OBJECT-TYPE    
  CeqfpMemoryResourceEntry  

ceqfpMemoryResType 1.3.6.1.4.1.9.9.715.1.1.7.1.1
This object indicates the type of the memory resource used by the QFP. This object is one of the indices to uniquely identify the QFP memory resource type.
Status: current Access: not-accessible
OBJECT-TYPE    
  CiscoQfpMemoryResource  

ceqfpMemoryResTotal 1.3.6.1.4.1.9.9.715.1.1.7.1.2
This object represents total memory available on this memory resource.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryResInUse 1.3.6.1.4.1.9.9.715.1.1.7.1.3
This object represents the memory which is currently under use on this memory resource.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryResFree 1.3.6.1.4.1.9.9.715.1.1.7.1.4
This object represents the memory which is currently free on this memory resource.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryResLowFreeWatermark 1.3.6.1.4.1.9.9.715.1.1.7.1.5
This object represents lowest free water mark on this memory resource.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryResRisingThreshold 1.3.6.1.4.1.9.9.715.1.1.7.1.6
This object represents the rising threshold value for this memory resource. A value of zero means that the rising threshold is not supported for this memory resource. The value of this object can not be set to lower than or equal to ceqfpMemoryResFallingThreshold. A rising (ceqfpMemoryResRisingThreshNotif) notification will be generated, whenever the memory resource usage (ceqfpMemoryHCResInUse) is equal to or greater than this value. After a rising notification is generated, another such notification will not be generated until the ceqfpMemoryResInUse falls below this value and reaches the ceqfpMemoryResFallingThreshold.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

ceqfpMemoryResFallingThreshold 1.3.6.1.4.1.9.9.715.1.1.7.1.7
This object represents the falling threshold value for this memory resource. A value of zero means that the falling threshold is not supported for this memory resource. The value of this object can not be set to higher than or equal to ceqfpMemoryResRisingThreshold. A falling (ceqfpMemoryResRisingThreshNotif) notification will be generated, whenever the memory resource usage (ceqfpMemoryHCResInUse) is equal to or lesser than this value. After a falling notification is generated, another such notification will not be generated until the ceqfpMemoryResInUse rises above this value and reaches the ceqfpMemoryResRisingThreshold.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

ceqfpMemoryResTotalOvrflw 1.3.6.1.4.1.9.9.715.1.1.7.1.8
This object represents the upper 32-bit of ceqfpMemoryResTotal. This object needs to be supported only when the value of ceqfpMemoryResTotal exceeds 32-bit, otherwise this object value would be set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryHCResTotal 1.3.6.1.4.1.9.9.715.1.1.7.1.9
This object is a 64-bit version of ceqfpMemoryResTotal.
Status: current Access: read-only
OBJECT-TYPE    
  CounterBasedGauge64  

ceqfpMemoryResInUseOvrflw 1.3.6.1.4.1.9.9.715.1.1.7.1.10
This object represents the upper 32-bit of ceqfpMemoryResInUse. This object needs to be supported only when the value of ceqfpMemoryResInUse exceeds 32-bit, otherwise this object value would be set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryHCResInUse 1.3.6.1.4.1.9.9.715.1.1.7.1.11
This object is a 64-bit version of ceqfpMemoryInRes.
Status: current Access: read-only
OBJECT-TYPE    
  CounterBasedGauge64  

ceqfpMemoryResFreeOvrflw 1.3.6.1.4.1.9.9.715.1.1.7.1.12
This object represents the upper 32-bit of ceqfpMemoryResFree. This object needs to be supported only when the value of ceqfpMemoryResFree exceeds 32-bit, otherwise this object value would be set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryHCResFree 1.3.6.1.4.1.9.9.715.1.1.7.1.13
This object is a 64-bit version of ceqfpMemoryResFree.
Status: current Access: read-only
OBJECT-TYPE    
  CounterBasedGauge64  

ceqfpMemoryResLowFreeWatermarkOvrflw 1.3.6.1.4.1.9.9.715.1.1.7.1.14
This object represents the upper 32-bit of ceqfpMemoryResLowFreeWatermark. This object needs to be supported only when the value of ceqfpMemoryResLowFreeWatermark exceeds 32-bit, otherwise this object value would be set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryHCResLowFreeWatermark 1.3.6.1.4.1.9.9.715.1.1.7.1.15
This object is a 64-bit version of ceqfpMemoryResLowFreeWatermark.
Status: current Access: read-only
OBJECT-TYPE    
  CounterBasedGauge64  

ceqfpThroughputTable 1.3.6.1.4.1.9.9.715.1.1.8
This table maintains the throughput information for each QFP physical entity. An agent creates a conceptual row to this table corresponding to a QFP physical entity upon detection of a physical entity supporting the QFP throughput information. An agent destroys a conceptual row from this table corresponding to a QFP physical entity upon removal of the QFP host physical entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CeqfpThroughputEntry

ceqfpThroughputEntry 1.3.6.1.4.1.9.9.715.1.1.8.1
A conceptual row in the ceqfpThroughputTable. There is an entry in this table for each QFP entity, as defined by a value of entPhysicalIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  CeqfpThroughputEntry  

ceqfpThroughputLicensedBW 1.3.6.1.4.1.9.9.715.1.1.8.1.1
This object represents the bandwidth for installed throughput license.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

ceqfpThroughputLevel 1.3.6.1.4.1.9.9.715.1.1.8.1.2
This object represents the current throughput level for installed throughput license. normal (1) - Throughput usage is normal warning (2) - Throughput usage has crossed the configured threshold limit exceed (3) - Throughput usage has exceeded the total licensed bandwidth
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), warning(2), exceed(3)  

ceqfpThroughputInterval 1.3.6.1.4.1.9.9.715.1.1.8.1.3
The object represents the configured time interval at which the ceqfpThroughputLevel is checked.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..86400  

ceqfpThroughputThreshold 1.3.6.1.4.1.9.9.715.1.1.8.1.4
The object represents the configured throughput threshold.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 75..95  

ceqfpThroughputAvgRate 1.3.6.1.4.1.9.9.715.1.1.8.1.5
The object represents the average throughput rate in the interval ceqfpThroughputInterval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

ceqfpMemoryResThreshNotifEnabled 1.3.6.1.4.1.9.9.715.1.2.1
This object controls memory resource rising and falling threshold notification. When this object contains a value 'true', then generation of memory resource threshold notification is enabled. If this object contains a value 'false', then generation of memory resource threshold notification is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ceqfpMemoryResCurrentRisingThresh 1.3.6.1.4.1.9.9.715.1.2.2
This object represents the current rising threshold value, which triggers the rising threshold notification (ceqfpMemoryResRisingThreshNotif).
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32 1..100  

ceqfpMemoryResCurrentFallingThresh 1.3.6.1.4.1.9.9.715.1.2.3
This object represents the current falling threshold value, which triggers the falling threshold notification (ceqfpMemoryResFallingThreshNotif).
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

ceqfpThroughputNotifEnabled 1.3.6.1.4.1.9.9.715.1.2.4
This object controls throughput rate notification. When this object contains a value 'true', then generation of ceqfpThroughputNotif is enabled. If this object contains a value 'false', then generation of ceqfpThroughputNotif is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ciscoEntityQfpMIBCompliances 1.3.6.1.4.1.9.9.715.2.1
OBJECT IDENTIFIER    

ceqfpMemoryResRisingThreshNotif 1.3.6.1.4.1.9.9.715.0.1
A notification indicating that the QFP memory usage is rising the threshold on this memory resource. This notification will be sent, whenever the QFP memory usage (ceqfpMemoryResInUse) is equal to or above the rising threshold (ceqfpMemoryResRisingThreshold). An agent may throttle the generation of consecutive ceqfpMemoryResRisingThreshNotif notification so that there is at least a five second (suggested default) gap between notification of this type.
Status: current Access: read-write
NOTIFICATION-TYPE    

ceqfpMemoryResFallingThreshNotif 1.3.6.1.4.1.9.9.715.0.2
A notification indicating that the QFP memory usage is equal to or below the falling threshold on this memory resource. This notification will be sent, whenever the QFP memory usage (ceqfpMemoryResInUse) is equal to or below the falling threshold (ceqfpMemoryResFallingThreshold). An agent may throttle the generation of consecutive ceqfpMemoryResFallingThreshNotif notification so that there is at least a five second (suggested default) gap between notification of this type.
Status: current Access: read-write
NOTIFICATION-TYPE    

ceqfpThroughputNotif 1.3.6.1.4.1.9.9.715.0.3
A notification indicating that the average throughput rate for the configured interval has exceeded the threshold or reached maximum bandwidth allowed. This notification will be sent, whenever the ceqfpThroughputLevel object has the value warning(2) or exceed(3). The condition for trap generation will be checked in every ceqfpThroughputInterval. ceqfpThroughputNotif with ceqfpThrougputLevel as warning(2) indicates that average throughput rate has crossed the configured threshold. ceqfpThroughputNotif with ceqfpThrougputLevel as exceed(3) indicates that average throughput rate has reached maximum licensed bandwidth.
Status: current Access: read-write
NOTIFICATION-TYPE    

ciscoEntityQfpMIBGroups 1.3.6.1.4.1.9.9.715.2.2
OBJECT IDENTIFIER    

ciscoEntityQfpMIBComplianceRev1 1.3.6.1.4.1.9.9.715.2.1.1
The compliance statement for CISCO-ENTITY-QFP-MIB
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

ciscoEntityQfpMIBComplianceRev2 1.3.6.1.4.1.9.9.715.2.1.2
The compliance statement for CISCO-ENTITY-QFP-MIB. This compliance module deprecates ciscoEntityQfpMIBComplianceRev1.
Status: current Access: read-only
MODULE-COMPLIANCE    

ciscoEntityQfpSystemGroup 1.3.6.1.4.1.9.9.715.2.2.1
This group contains collection of QFP system information.
Status: current Access: read-only
OBJECT-GROUP    

ciscoEntityQfpUtilizationAlgoGroup 1.3.6.1.4.1.9.9.715.2.2.2
This group contains collection of QFP utilization algorithm objects.
Status: current Access: read-only
OBJECT-GROUP    

ciscoEntityQfpUtilizationGroup 1.3.6.1.4.1.9.9.715.2.2.3
This group contains collection of QFP utilization information.
Status: current Access: read-only
OBJECT-GROUP    

ciscoEntityQfpMemoryResourceGroup 1.3.6.1.4.1.9.9.715.2.2.4
This group contains collection of QFP memory resource information.
Status: current Access: read-only
OBJECT-GROUP    

ciscoEntityQfpNotifGroup 1.3.6.1.4.1.9.9.715.2.2.5
This group contains collection of QFP notifications.
Status: current Access: read-only
NOTIFICATION-GROUP    

ciscoEntityQfpMemoryResNotifGroup 1.3.6.1.4.1.9.9.715.2.2.6
This group contains memory resource notification control objects.
Status: current Access: read-only
OBJECT-GROUP    

ciscoEntityQfpMemoryResourceOvrflwGroup 1.3.6.1.4.1.9.9.715.2.2.7
This group contains collection of upper 32-bit QFP memory resource information.
Status: current Access: read-only
OBJECT-GROUP    

ciscoEntityQfpMemoryHCResourceGroup 1.3.6.1.4.1.9.9.715.2.2.8
This group contains collection of high capacity(HC) objects of QFP memory resource information.
Status: current Access: read-only
OBJECT-GROUP    

ceqfpThroughputGroup 1.3.6.1.4.1.9.9.715.2.2.9
This group contains collection of throughput rate information.
Status: current Access: read-only
OBJECT-GROUP