CISCO-IDSL-LINE-MIB

File: CISCO-IDSL-LINE-MIB.mib (77758 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
CISCO-SMI IF-MIB PerfHist-TC-MIB
SNMP-FRAMEWORK-MIB ADSL-LINE-MIB

Imported symbols

Integer32 Counter32 Gauge32
MODULE-IDENTITY OBJECT-TYPE TruthValue
VariablePointer TEXTUAL-CONVENTION MODULE-COMPLIANCE
OBJECT-GROUP ciscoMgmt ifIndex
InterfaceIndex PerfCurrentCount PerfIntervalCount
SnmpAdminString AdslLineProfileName adslLineConfProfileName

Defined Types

IdslPerfTimeElapsed  
The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
TEXTUAL-CONVENTION    
  Gauge32  

IdslPerfCurrDayCount  
A counter associated with interval performance measurements in a current 1-day (24 hour) measurement interval. The value of this counter starts at zero at the beginning of an interval and increases when associated events occur, until the end of the 1-day interval. At that time, the agent stores the value of the counter in the previous 1-day history interval, if available, and resets the value of the counter to zero. In the case where the agent has no valid data available for this interval, the corresponding object instance is not available. In this case, the agent will respond with the appropriate error indicating that the instance does not exist; that is, 'noSuchName' in response to a SNMPv1 get request, and 'noSuchInstance' in response to a SNMPv2 get request.
TEXTUAL-CONVENTION    
  Gauge32  

IdslPerfPrevDayCount  
A counter associated with interval performance measurements during the most previous 1-day (24 hour) measurement interval. The value of this counter is equal to the current day counter at the end of its most recent interval. In the case where the agent has no valid data available for this interval, the corresponding object instance is not available. In this case, the agent will respond with the appropriate error indicating that the instance does not exist; that is, 'noSuchName' in response to a SNMPv1 get request, and 'noSuchInstance' in response to a SNMPv2 get request.
TEXTUAL-CONVENTION    
  Gauge32  

CIdslLineEntry  
SEQUENCE    
  cIdslLineSpecific VariablePointer
  cIdslLineConfProfile AdslLineProfileName
  cIdslLineAlarmConfProfile AdslLineProfileName

CIdslItucPhysEntry  
SEQUENCE    
  cIdslItucInvSerialNumber SnmpAdminString
  cIdslItucInvVendorId SnmpAdminString
  cIdslItucInvVersionNumber SnmpAdminString
  cIdslItucStatus INTEGER

CIdslItucPerfDataEntry  
SEQUENCE    
  cIdslItucPerfCVs Counter32
  cIdslItucPerfESs Counter32
  cIdslItucPerfSESs Counter32
  cIdslItucPerfHdlcCVs Counter32
  cIdslItucPerfHdlcAborts Counter32
  cIdslItucPerfHdlcAligns Counter32
  cIdslItucPerfHdlcShorts Counter32
  cIdslItucPerfHdlcLongs Counter32
  cIdslItucPerfValidIntervals INTEGER
  cIdslItucPerfInvalidIntervals INTEGER
  cIdslItucPerfCurr15MinElapsed IdslPerfTimeElapsed
  cIdslItucPerfCurr15MinCVs PerfCurrentCount
  cIdslItucPerfCurr15MinESs PerfCurrentCount
  cIdslItucPerfCurr15MinSESs PerfCurrentCount
  cIdslItucPerfCurr15MinHdlcCVs PerfCurrentCount
  cIdslItucPerfCurr15MinHdlcAborts PerfCurrentCount
  cIdslItucPerfCurr15MinHdlcAligns PerfCurrentCount
  cIdslItucPerfCurr15MinHdlcShorts PerfCurrentCount
  cIdslItucPerfCurr15MinHdlcLongs PerfCurrentCount
  cIdslItucPerfCurr1DayElapsed IdslPerfTimeElapsed
  cIdslItucPerfCurr1DayCVs IdslPerfCurrDayCount
  cIdslItucPerfCurr1DayESs IdslPerfCurrDayCount
  cIdslItucPerfCurr1DaySESs IdslPerfCurrDayCount
  cIdslItucPerfCurr1DayHdlcCVs IdslPerfCurrDayCount
  cIdslItucPerfCurr1DayHdlcAborts IdslPerfCurrDayCount
  cIdslItucPerfCurr1DayHdlcAligns IdslPerfCurrDayCount
  cIdslItucPerfCurr1DayHdlcShorts IdslPerfCurrDayCount
  cIdslItucPerfCurr1DayHdlcLongs IdslPerfCurrDayCount
  cIdslItucPerfPrev1DayMoniSecs INTEGER
  cIdslItucPerfPrev1DayCVs IdslPerfPrevDayCount
  cIdslItucPerfPrev1DayESs IdslPerfPrevDayCount
  cIdslItucPerfPrev1DaySESs IdslPerfPrevDayCount
  cIdslItucPerfPrev1DayHdlcCVs IdslPerfPrevDayCount
  cIdslItucPerfPrev1DayHdlcAborts IdslPerfPrevDayCount
  cIdslItucPerfPrev1DayHdlcAligns IdslPerfPrevDayCount
  cIdslItucPerfPrev1DayHdlcShorts IdslPerfPrevDayCount
  cIdslItucPerfPrev1DayHdlcLongs IdslPerfPrevDayCount

CIdslIturPerfDataEntry  
SEQUENCE    
  cIdslIturPerfCVs Counter32
  cIdslIturPerfESs Counter32
  cIdslIturPerfSESs Counter32
  cIdslIturPerfValidIntervals INTEGER
  cIdslIturPerfInvalidIntervals INTEGER
  cIdslIturPerfCurr15MinElapsed IdslPerfTimeElapsed
  cIdslIturPerfCurr15MinCVs PerfCurrentCount
  cIdslIturPerfCurr15MinESs PerfCurrentCount
  cIdslIturPerfCurr15MinSESs PerfCurrentCount
  cIdslIturPerfCurr1DayElapsed IdslPerfTimeElapsed
  cIdslIturPerfCurr1DayCVs IdslPerfCurrDayCount
  cIdslIturPerfCurr1DayESs IdslPerfCurrDayCount
  cIdslIturPerfCurr1DaySESs IdslPerfCurrDayCount
  cIdslIturPerfPrev1DayMoniSecs INTEGER
  cIdslIturPerfPrev1DayCVs IdslPerfPrevDayCount
  cIdslIturPerfPrev1DayESs IdslPerfPrevDayCount
  cIdslIturPerfPrev1DaySESs IdslPerfPrevDayCount

CIdslItucIntervalEntry  
SEQUENCE    
  cIdslItucIntervalNumber INTEGER
  cIdslItucIntervalValidData TruthValue
  cIdslItucIntervalCVs PerfIntervalCount
  cIdslItucIntervalESs PerfIntervalCount
  cIdslItucIntervalSESs PerfIntervalCount
  cIdslItucIntervalHdlcCVs PerfIntervalCount
  cIdslItucIntervalHdlcAborts PerfIntervalCount
  cIdslItucIntervalHdlcAligns PerfIntervalCount
  cIdslItucIntervalHdlcShorts PerfIntervalCount
  cIdslItucIntervalHdlcLongs PerfIntervalCount

CIdslIturIntervalEntry  
SEQUENCE    
  cIdslIturIntervalNumber INTEGER
  cIdslIturIntervalValidData TruthValue
  cIdslIturIntervalCVs PerfIntervalCount
  cIdslIturIntervalESs PerfIntervalCount
  cIdslIturIntervalSESs PerfIntervalCount

CIdslLineConfProfileEntry  
SEQUENCE    
  cIdslLineConfRate INTEGER
  cIdslLineConfProtocol INTEGER
  cIdslLineConfLmiProtocol INTEGER
  cIdslLineConfLmiNetN392 INTEGER
  cIdslLineConfLmiNetN393 INTEGER
  cIdslLineConfLmiNetT392 INTEGER
  cIdslLineConfUpcIntent INTEGER
  cIdslLineConfBcDefault Integer32

CIdslPppoaPerfDataEntry  
SEQUENCE    
  cIdslPppoaPerfRTOs Counter32
  cIdslPppoaPerfCVs Counter32
  cIdslPppoaPerfShorts Counter32
  cIdslPppoaPerfLongs Counter32
  cIdslPppoaPerfDiscards Counter32
  cIdslPppoaPerfValidIntervals INTEGER
  cIdslPppoaPerfInvalidIntervals INTEGER
  cIdslPppoaPerfCurr15MinElapsed IdslPerfTimeElapsed
  cIdslPppoaPerfCurr15MinRTOs PerfCurrentCount
  cIdslPppoaPerfCurr15MinCVs PerfCurrentCount
  cIdslPppoaPerfCurr15MinShorts PerfCurrentCount
  cIdslPppoaPerfCurr15MinLongs PerfCurrentCount
  cIdslPppoaPerfCurr15MinDiscards PerfCurrentCount
  cIdslPppoaPerfCurr1DayElapsed IdslPerfTimeElapsed
  cIdslPppoaPerfCurr1DayRTOs IdslPerfCurrDayCount
  cIdslPppoaPerfCurr1DayCVs IdslPerfCurrDayCount
  cIdslPppoaPerfCurr1DayShorts IdslPerfCurrDayCount
  cIdslPppoaPerfCurr1DayLongs IdslPerfCurrDayCount
  cIdslPppoaPerfCurr1DayDiscards IdslPerfCurrDayCount
  cIdslPppoaPerfPrev1DayMoniSecs INTEGER
  cIdslPppoaPerfPrev1DayRTOs IdslPerfPrevDayCount
  cIdslPppoaPerfPrev1DayCVs IdslPerfPrevDayCount
  cIdslPppoaPerfPrev1DayShorts IdslPerfPrevDayCount
  cIdslPppoaPerfPrev1DayLongs IdslPerfPrevDayCount
  cIdslPppoaPerfPrev1DayDiscards IdslPerfPrevDayCount

CIdslPppoaIntervalEntry  
SEQUENCE    
  cIdslPppoaIntervalNumber INTEGER
  cIdslPppoaIntervalValidData TruthValue
  cIdslPppoaIntervalRTOs PerfIntervalCount
  cIdslPppoaIntervalCVs PerfIntervalCount
  cIdslPppoaIntervalShorts PerfIntervalCount
  cIdslPppoaIntervalLongs PerfIntervalCount
  cIdslPppoaIntervalDiscards PerfIntervalCount

CIdslPppoaMapEntry  
SEQUENCE    
  cIdslPppoaMapIfIndex InterfaceIndex
  cIdslPppoaMapVpi INTEGER
  cIdslPppoaMapVci INTEGER

Defined Values

ciscoIdslLineMIB 1.3.6.1.4.1.9.9.154
This MIB module describes IDSL (ISDN Digital Line Subscriber) line interfaces. The structure of this module resembles that of the ADSL-LINE-MIB (RFC-2662). Observe that the tables in this module do not necessarily extend the tables defined by the ADSL-LINE-MIB. Currently, only those tables that contain configuration information extend the profile tables defined by the ADSL-LINE-MIB. This allows the management client to define xDSL configuration profiles that apply across all xDSL modems, independent of the technology being utilized by the modem. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** ADSL - Asymmetric Digital Subscriber Line. ATM - Asynchronous Transfer Mode. BRITE - Basic Rate Interface Terminal Extender. CV - Coding Violation. DLC - Data Link Connection. DSL - Digital Subscriber Line. ES - Error Second. IDSL - IDSN Digital Subscriber Loop. ITU-C - IDSL Transceiver Unit, Central Office end. ITU-R - IDSL Transceiver Unit, Remote terminal end. LMI - Link Management Interface. LOF - Loss Of Frame. LOS - Loss Of Signal. NT - Network Terminator. PPP - Point-to-Point Protocol. PPPoA - PPP over ATM. SES - Severely Errored Second. *** DEFINITIONS *** CODING VIOLATION A coding violation occurs when the incoming signal exhibits a CRC anomaly. DOWNSTREAM The flow of data in the direction from the ITU-C to ITU-R. ERRORED SECOND A second with one or more coding violations. LINE RATE The total data rate supported by a line. Observe that the payload rate is equal the line rate for the earliest implementations of IDSL. However, the payload rate maybe less than the line rate for future implementations. SEVERELY ERRORED SECOND A second with 3 or more coding violations. UPSTREAM The flow of data in the direction from the ATU-R to ATU-C.
MODULE-IDENTITY    

ciscoIdslLineMIBObjects 1.3.6.1.4.1.9.9.154.1
OBJECT IDENTIFIER    

cIdslLineTable 1.3.6.1.4.1.9.9.154.1.1
This table contains the common attributes describing both ends of IDSL lines supported by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIdslLineEntry

cIdslLineEntry 1.3.6.1.4.1.9.9.154.1.1.1
A set of common attributes describing both ends of an IDSL line supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154).
Status: current Access: not-accessible
OBJECT-TYPE    
  CIdslLineEntry  

cIdslLineSpecific 1.3.6.1.4.1.9.9.154.1.1.1.1
This object specifies an object identifier of an instance of an object in the MIB. The implementation determines the application of this object. For example, an implementation may use this object to provide a reference to the port-class physical entity (see the ENTITY-MIB for further details) corresponding to the IDSL line.
Status: current Access: read-only
OBJECT-TYPE    
  VariablePointer  

cIdslLineConfProfile 1.3.6.1.4.1.9.9.154.1.1.1.2
This object specifies the row in the adslLineConfProfileTable (see the ADSL-LINE-MIB for further details), which applies for this IDSL line interface. In the case the implementation utilizes 'dynamic mode' (see the ADSL-LINE-MIB for further details), then the value of this object defaults to the name of a configuration profile designated by the implementation as the default configuration profile. In the case the implementation utilizes 'static mode', then the the value of this object is read-only.
Status: current Access: read-write
OBJECT-TYPE    
  AdslLineProfileName  

cIdslLineAlarmConfProfile 1.3.6.1.4.1.9.9.154.1.1.1.3
This object specifies the row in the adslLineAlarmConfProfileTable (see the ADSL-LINE-MIB for further details), which applies for this IDSL line interface. In the case the implementation utilizes 'dynamic mode' (see the ADSL-LINE-MIB for further details), then the value of this object defaults to the name of an alarm configuration profile designated by the implementation as the default alarm configuration profile. In the case the implementation utilizes 'static mode', then the the value of this object is read-only.
Status: current Access: read-write
OBJECT-TYPE    
  AdslLineProfileName  

cIdslItucPhysTable 1.3.6.1.4.1.9.9.154.1.2
This table contains physical-layer parameters for ITU-C class devices supported by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIdslItucPhysEntry

cIdslItucPhysEntry 1.3.6.1.4.1.9.9.154.1.2.1
A set of physical-layer parameters for an ITU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154).
Status: current Access: not-accessible
OBJECT-TYPE    
  CIdslItucPhysEntry  

cIdslItucInvSerialNumber 1.3.6.1.4.1.9.9.154.1.2.1.1
This object specifies the vendor specific string that identifies the vendor ITU-C.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cIdslItucInvVendorId 1.3.6.1.4.1.9.9.154.1.2.1.2
This object specifies the vendor identifier assigned according to ANSI T1.220.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cIdslItucInvVersionNumber 1.3.6.1.4.1.9.9.154.1.2.1.3
This object specifies the vendor specific version number of the ITU-C.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cIdslItucStatus 1.3.6.1.4.1.9.9.154.1.2.1.4
This object specifies the state of the ITU-C transceiver: - loopDown The IDSL link is down, as a result of a near-end has detected a LOS, a LOF, has not exchanged an ACT bit with the downstream BRITE/NT1, or similar fault/condition. - dslSync The IDSL link has achieved physical layer activation with the first downstream entity (iether a BRITE or the NT1). - loopUp The IDSL link has exchanged the ACT bit with the NT1, but LMI signalling is not yet active. This is the normal operating state for PPP operation. - loopUpLmiActive The IDSL link has exchnaged the ACT bit with the NT1 and the LMI signalling is active. This is the normal operating state for frame relay operation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER loopDown(1), dslSync(2), loopUp(3), loopUpLmiActive(4)  

cIdslItucPerfDataTable 1.3.6.1.4.1.9.9.154.1.6
This table contains physical-layer statistics for ITU-C class devices supported by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIdslItucPerfDataEntry

cIdslItucPerfDataEntry 1.3.6.1.4.1.9.9.154.1.6.1
A set of physical-layer statistics for an ITU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154).
Status: current Access: not-accessible
OBJECT-TYPE    
  CIdslItucPerfDataEntry  

cIdslItucPerfCVs 1.3.6.1.4.1.9.9.154.1.6.1.1
This object specifies the number of coding violations experienced by the ITU-C since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslItucPerfESs 1.3.6.1.4.1.9.9.154.1.6.1.2
This object specifies the number of errored seconds experienced by the ITU-C since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslItucPerfSESs 1.3.6.1.4.1.9.9.154.1.6.1.3
This object specifies the number of severely errored seconds experienced by the ITU-C since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslItucPerfHdlcCVs 1.3.6.1.4.1.9.9.154.1.6.1.4
This object specifies the number of HDLC coding violations experienced by the ITU-C since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslItucPerfHdlcAborts 1.3.6.1.4.1.9.9.154.1.6.1.5
This object specifies the number of HDLC aborts experienced by the ITU-C since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslItucPerfHdlcAligns 1.3.6.1.4.1.9.9.154.1.6.1.6
This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslItucPerfHdlcShorts 1.3.6.1.4.1.9.9.154.1.6.1.7
This object specifies the number of short HDLC frames received by the ITU-C since agent reset. A short HDLC frame contains less than 5 octets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslItucPerfHdlcLongs 1.3.6.1.4.1.9.9.154.1.6.1.8
This object specifies the number of long HDLC frames received by the ITU-C since agent reset. A long HDLC frame contains more than 1500 octets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslItucPerfValidIntervals 1.3.6.1.4.1.9.9.154.1.6.1.9
The number of previous near-end performance data 15-minute intervals for which data was collected. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15-minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

cIdslItucPerfInvalidIntervals 1.3.6.1.4.1.9.9.154.1.6.1.10
The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

cIdslItucPerfCurr15MinElapsed 1.3.6.1.4.1.9.9.154.1.6.1.11
The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfTimeElapsed  

cIdslItucPerfCurr15MinCVs 1.3.6.1.4.1.9.9.154.1.6.1.12
This object specifies the number of coding violations experienced by the ITU-C in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslItucPerfCurr15MinESs 1.3.6.1.4.1.9.9.154.1.6.1.13
This object specifies the number of errored seconds experienced by the ITU-C in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslItucPerfCurr15MinSESs 1.3.6.1.4.1.9.9.154.1.6.1.14
This object specifies the number of severely errored seconds experienced by the ITU-C in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslItucPerfCurr15MinHdlcCVs 1.3.6.1.4.1.9.9.154.1.6.1.15
This object specifies the number of HDLC coding violations experienced by the ITU-C in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslItucPerfCurr15MinHdlcAborts 1.3.6.1.4.1.9.9.154.1.6.1.16
This object specifies the number of HDLC aborts experienced by the ITU-C in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslItucPerfCurr15MinHdlcAligns 1.3.6.1.4.1.9.9.154.1.6.1.17
This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslItucPerfCurr15MinHdlcShorts 1.3.6.1.4.1.9.9.154.1.6.1.18
This object specifies the number of short HDLC frames received by the ITU-C since agent in the current 15-minute interval. A short HDLC frame contains less than 5 octets.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslItucPerfCurr15MinHdlcLongs 1.3.6.1.4.1.9.9.154.1.6.1.19
This object specifies the number of long HDLC frames received by the ITU-C since agent in the current 15-minute interval. A long HDLC frame contains more than 1500 octets.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslItucPerfCurr1DayElapsed 1.3.6.1.4.1.9.9.154.1.6.1.20
The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfTimeElapsed  

cIdslItucPerfCurr1DayCVs 1.3.6.1.4.1.9.9.154.1.6.1.21
This object specifies the number of coding violations experienced by the ITU-C in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslItucPerfCurr1DayESs 1.3.6.1.4.1.9.9.154.1.6.1.22
This object specifies the number of errored seconds experienced by the ITU-C in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslItucPerfCurr1DaySESs 1.3.6.1.4.1.9.9.154.1.6.1.23
This object specifies the number of severely errored seconds experienced by the ITU-C in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslItucPerfCurr1DayHdlcCVs 1.3.6.1.4.1.9.9.154.1.6.1.24
This object specifies the number of HDLC coding violations experienced by the ITU-C in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslItucPerfCurr1DayHdlcAborts 1.3.6.1.4.1.9.9.154.1.6.1.25
This object specifies the number of HDLC aborts experienced by the ITU-C in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslItucPerfCurr1DayHdlcAligns 1.3.6.1.4.1.9.9.154.1.6.1.26
This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslItucPerfCurr1DayHdlcShorts 1.3.6.1.4.1.9.9.154.1.6.1.27
This object specifies the number of short HDLC frames received by the ITU-C since agent in the current 1-day interval. A short HDLC frame contains less than 5 octets.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslItucPerfCurr1DayHdlcLongs 1.3.6.1.4.1.9.9.154.1.6.1.28
This object specifies the number of long HDLC frames received by the ITU-C since agent in the current 1-day interval. A long HDLC frame contains more than 1500 octets.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslItucPerfPrev1DayMoniSecs 1.3.6.1.4.1.9.9.154.1.6.1.29
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..86400  

cIdslItucPerfPrev1DayCVs 1.3.6.1.4.1.9.9.154.1.6.1.30
This object specifies the number of coding violations experienced by the ITU-C in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslItucPerfPrev1DayESs 1.3.6.1.4.1.9.9.154.1.6.1.31
This object specifies the number of errored seconds experienced by the ITU-C in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslItucPerfPrev1DaySESs 1.3.6.1.4.1.9.9.154.1.6.1.32
This object specifies the number of severely errored seconds experienced by the ITU-C in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslItucPerfPrev1DayHdlcCVs 1.3.6.1.4.1.9.9.154.1.6.1.33
This object specifies the number of HDLC coding violations experienced by the ITU-C in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslItucPerfPrev1DayHdlcAborts 1.3.6.1.4.1.9.9.154.1.6.1.34
This object specifies the number of HDLC aborts experienced by the ITU-C in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslItucPerfPrev1DayHdlcAligns 1.3.6.1.4.1.9.9.154.1.6.1.35
This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslItucPerfPrev1DayHdlcShorts 1.3.6.1.4.1.9.9.154.1.6.1.36
This object specifies the number of long HDLC frames received by the ITU-C since agent in the previous 1-day interval. A long HDLC frame contains more than 1500 octets.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslItucPerfPrev1DayHdlcLongs 1.3.6.1.4.1.9.9.154.1.6.1.37
This object specifies the number of long HDLC frames received by the ITU-C since agent in the previous 1-day interval. A long HDLC frame contains more than 1500 octets.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslIturPerfDataTable 1.3.6.1.4.1.9.9.154.1.7
This table contains physical-layer statistics for ITU-R class devices supported by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIdslIturPerfDataEntry

cIdslIturPerfDataEntry 1.3.6.1.4.1.9.9.154.1.7.1
A set of physical-layer statistics for an ITU-R class device supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154).
Status: current Access: not-accessible
OBJECT-TYPE    
  CIdslIturPerfDataEntry  

cIdslIturPerfCVs 1.3.6.1.4.1.9.9.154.1.7.1.1
This object specifies the number of coding violations experienced by the ITU-R since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslIturPerfESs 1.3.6.1.4.1.9.9.154.1.7.1.2
This object specifies the number of errored seconds experienced by the ITU-R since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslIturPerfSESs 1.3.6.1.4.1.9.9.154.1.7.1.3
This object specifies the number of severely errored seconds experienced by the ITU-R since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslIturPerfValidIntervals 1.3.6.1.4.1.9.9.154.1.7.1.4
The number of previous near-end performance data 15-minute intervals for which data was collected. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15-minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

cIdslIturPerfInvalidIntervals 1.3.6.1.4.1.9.9.154.1.7.1.5
The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

cIdslIturPerfCurr15MinElapsed 1.3.6.1.4.1.9.9.154.1.7.1.6
The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfTimeElapsed  

cIdslIturPerfCurr15MinCVs 1.3.6.1.4.1.9.9.154.1.7.1.7
This object specifies the number of coding violations experienced by the ITU-R in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslIturPerfCurr15MinESs 1.3.6.1.4.1.9.9.154.1.7.1.8
This object specifies the number of errored seconds experienced by the ITU-R in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslIturPerfCurr15MinSESs 1.3.6.1.4.1.9.9.154.1.7.1.9
This object specifies the number of severely errored seconds experienced by the ITU-R in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslIturPerfCurr1DayElapsed 1.3.6.1.4.1.9.9.154.1.7.1.10
The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfTimeElapsed  

cIdslIturPerfCurr1DayCVs 1.3.6.1.4.1.9.9.154.1.7.1.11
This object specifies the number of coding violations experienced by the ITU-R in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslIturPerfCurr1DayESs 1.3.6.1.4.1.9.9.154.1.7.1.12
This object specifies the number of errored seconds experienced by the ITU-R in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslIturPerfCurr1DaySESs 1.3.6.1.4.1.9.9.154.1.7.1.13
This object specifies the number of severely errored seconds experienced by the ITU-R in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslIturPerfPrev1DayMoniSecs 1.3.6.1.4.1.9.9.154.1.7.1.14
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..86400  

cIdslIturPerfPrev1DayCVs 1.3.6.1.4.1.9.9.154.1.7.1.15
This object specifies the number of coding violations experienced by the ITU-R in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslIturPerfPrev1DayESs 1.3.6.1.4.1.9.9.154.1.7.1.16
This object specifies the number of errored seconds experienced by the ITU-R in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslIturPerfPrev1DaySESs 1.3.6.1.4.1.9.9.154.1.7.1.17
This object specifies the number of severely errored seconds experienced by the ITU-R in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslItucIntervalTable 1.3.6.1.4.1.9.9.154.1.8
This table contains physical-layer statistics intervals for ITU-C class devices supported by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIdslItucIntervalEntry

cIdslItucIntervalEntry 1.3.6.1.4.1.9.9.154.1.8.1
A 15-miute interval of physical-layer statistics for a ITU-C class device supported by the system. There exists up to 96 entries for each ifEntry with an ifType of idsl(154).
Status: current Access: not-accessible
OBJECT-TYPE    
  CIdslItucIntervalEntry  

cIdslItucIntervalNumber 1.3.6.1.4.1.9.9.154.1.8.1.1
The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval collected 24 hours ago. Intervals 2..96 are optional.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

cIdslItucIntervalValidData 1.3.6.1.4.1.9.9.154.1.8.1.2
This object specifies whether the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cIdslItucIntervalCVs 1.3.6.1.4.1.9.9.154.1.8.1.3
This object specifies the number of coding violations experienced by the ITU-C in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslItucIntervalESs 1.3.6.1.4.1.9.9.154.1.8.1.4
This object specifies the number of errored seconds experienced by the ITU-C in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslItucIntervalSESs 1.3.6.1.4.1.9.9.154.1.8.1.5
This object specifies the number of severely errored seconds experienced by the ITU-C in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslItucIntervalHdlcCVs 1.3.6.1.4.1.9.9.154.1.8.1.6
This object specifies the number of HDLC coding violations experienced by the ITU-C in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslItucIntervalHdlcAborts 1.3.6.1.4.1.9.9.154.1.8.1.7
This object specifies the number of HDLC aborts experienced by the ITU-C in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslItucIntervalHdlcAligns 1.3.6.1.4.1.9.9.154.1.8.1.8
This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslItucIntervalHdlcShorts 1.3.6.1.4.1.9.9.154.1.8.1.9
This object specifies the number of short HDLC frames received by the ITU-C since agent in the interval. A short HDLC frame contains less than 5 octets.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslItucIntervalHdlcLongs 1.3.6.1.4.1.9.9.154.1.8.1.10
This object specifies the number of long HDLC frames received by the ITU-C since agent in the interval. A long HDLC frame contains more than 1500 octets.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslIturIntervalTable 1.3.6.1.4.1.9.9.154.1.9
This table contains physical-layer statistics intervals for ITU-R class devices supported by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIdslIturIntervalEntry

cIdslIturIntervalEntry 1.3.6.1.4.1.9.9.154.1.9.1
A 15-miute interval of physical-layer statistics for a ITU-R class device supported by the system. There exists up to 96 entries for each ifEntry with an ifType of idsl(154).
Status: current Access: not-accessible
OBJECT-TYPE    
  CIdslIturIntervalEntry  

cIdslIturIntervalNumber 1.3.6.1.4.1.9.9.154.1.9.1.1
The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval collected 24 hours ago. Intervals 2..96 are optional.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

cIdslIturIntervalValidData 1.3.6.1.4.1.9.9.154.1.9.1.2
This object specifies whether the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cIdslIturIntervalCVs 1.3.6.1.4.1.9.9.154.1.9.1.3
This object specifies the number of coding violations experienced by the ITU-R in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslIturIntervalESs 1.3.6.1.4.1.9.9.154.1.9.1.4
This object specifies the number of errored seconds experienced by the ITU-R in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslIturIntervalSESs 1.3.6.1.4.1.9.9.154.1.9.1.5
This object specifies the number of severely errored seconds experienced by the ITU-R in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslLineConfProfileTable 1.3.6.1.4.1.9.9.154.1.14
This table extends the adslLineConfProfileTable and contains IDSL line configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIdslLineConfProfileEntry

cIdslLineConfProfileEntry 1.3.6.1.4.1.9.9.154.1.14.1
A configuration profile containing enterprise-specific IDSL line configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  CIdslLineConfProfileEntry  

cIdslLineConfRate 1.3.6.1.4.1.9.9.154.1.14.1.1
This object specifies the desired line rate.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER rate144k(1), rate144kIdl(2), rate128k(3), rate64k(4), rate56k(5)  

cIdslLineConfProtocol 1.3.6.1.4.1.9.9.154.1.14.1.2
This object specifies the layer 2 protocol to be employed by the line, and more specifically the encapsulation type: - frf Specifies the frame relay layer 2 protocol defined by FRF.8. Observe that the encapsulation can be selected per virtual circuit. - pppMuxCisco Specifies the PPP using Cisco proprietary virtual circuit multiplexed encapsulation. - pppMuxIetf Specifies the PPP using virtual circuit multiplexed encapsulation defined by RFC-2364. - pppLlcIetf Specifies the PPP using the LLC (Link Layer Control) encapsulation defined by RFC-2364.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER frf(1), pppMuxCisco(2), pppMuxIetf(3), pppLlcIetf(4)  

cIdslLineConfLmiProtocol 1.3.6.1.4.1.9.9.154.1.14.1.3
This object identifies the local inband signaling protocol.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noLmiConfigured(1), lmiRev1(2), ansiT1617D(3), ansiT1617B(4), itut933A(5), ansiT1617D1994(6)  

cIdslLineConfLmiNetN392 1.3.6.1.4.1.9.9.154.1.14.1.4
This object specifies the interval between successive status enquiry messages.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..10  

cIdslLineConfLmiNetN393 1.3.6.1.4.1.9.9.154.1.14.1.5
This object specifies the value of the network-side error threshold.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..10  

cIdslLineConfLmiNetT392 1.3.6.1.4.1.9.9.154.1.14.1.6
This object specifies the value of the network-side polling verification timer.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 5..30  

cIdslLineConfUpcIntent 1.3.6.1.4.1.9.9.154.1.14.1.7
This object specifies the default UPC (Usage Parameter Control) action for connections that do not explicitly specify a UPC action.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER pass(1), tagDrop(2), tag(3), drop(4)  

cIdslLineConfBcDefault 1.3.6.1.4.1.9.9.154.1.14.1.8
This object specifies the default BC (Committed Burst Size) for connections that do not explicitly specify a BC.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cIdslPppoaPerfDataTable 1.3.6.1.4.1.9.9.154.1.16
This table contains PPPoA statistics for those ITU-C class devices configured for PPP operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIdslPppoaPerfDataEntry

cIdslPppoaPerfDataEntry 1.3.6.1.4.1.9.9.154.1.16.1
A set of PPPoA statistics for an ITU-C class device configured for PPP operation. There exists an entry for each ifEntry that meet the following criteria: 1) The ifEntry has an ifType of idsl(154); 2) The profile associated with the ITU-C class device specifies a value of 'ppp' for the cIdslLineProtocol object.
Status: current Access: not-accessible
OBJECT-TYPE    
  CIdslPppoaPerfDataEntry  

cIdslPppoaPerfRTOs 1.3.6.1.4.1.9.9.154.1.16.1.1
This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslPppoaPerfCVs 1.3.6.1.4.1.9.9.154.1.16.1.2
This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslPppoaPerfShorts 1.3.6.1.4.1.9.9.154.1.16.1.3
This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslPppoaPerfLongs 1.3.6.1.4.1.9.9.154.1.16.1.4
This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslPppoaPerfDiscards 1.3.6.1.4.1.9.9.154.1.16.1.5
This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cIdslPppoaPerfValidIntervals 1.3.6.1.4.1.9.9.154.1.16.1.6
The number of previous near-end performance data 15-minute intervals for which data was collected. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15-minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

cIdslPppoaPerfInvalidIntervals 1.3.6.1.4.1.9.9.154.1.16.1.7
The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

cIdslPppoaPerfCurr15MinElapsed 1.3.6.1.4.1.9.9.154.1.16.1.8
The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfTimeElapsed  

cIdslPppoaPerfCurr15MinRTOs 1.3.6.1.4.1.9.9.154.1.16.1.9
This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslPppoaPerfCurr15MinCVs 1.3.6.1.4.1.9.9.154.1.16.1.10
This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslPppoaPerfCurr15MinShorts 1.3.6.1.4.1.9.9.154.1.16.1.11
This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslPppoaPerfCurr15MinLongs 1.3.6.1.4.1.9.9.154.1.16.1.12
This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslPppoaPerfCurr15MinDiscards 1.3.6.1.4.1.9.9.154.1.16.1.13
This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

cIdslPppoaPerfCurr1DayElapsed 1.3.6.1.4.1.9.9.154.1.16.1.14
The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfTimeElapsed  

cIdslPppoaPerfCurr1DayRTOs 1.3.6.1.4.1.9.9.154.1.16.1.15
This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslPppoaPerfCurr1DayCVs 1.3.6.1.4.1.9.9.154.1.16.1.16
This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslPppoaPerfCurr1DayShorts 1.3.6.1.4.1.9.9.154.1.16.1.17
This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslPppoaPerfCurr1DayLongs 1.3.6.1.4.1.9.9.154.1.16.1.18
This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslPppoaPerfCurr1DayDiscards 1.3.6.1.4.1.9.9.154.1.16.1.19
This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the current 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfCurrDayCount  

cIdslPppoaPerfPrev1DayMoniSecs 1.3.6.1.4.1.9.9.154.1.16.1.20
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..86400  

cIdslPppoaPerfPrev1DayRTOs 1.3.6.1.4.1.9.9.154.1.16.1.21
This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslPppoaPerfPrev1DayCVs 1.3.6.1.4.1.9.9.154.1.16.1.22
This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslPppoaPerfPrev1DayShorts 1.3.6.1.4.1.9.9.154.1.16.1.23
This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslPppoaPerfPrev1DayLongs 1.3.6.1.4.1.9.9.154.1.16.1.24
This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslPppoaPerfPrev1DayDiscards 1.3.6.1.4.1.9.9.154.1.16.1.25
This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the previous 1-day interval.
Status: current Access: read-only
OBJECT-TYPE    
  IdslPerfPrevDayCount  

cIdslPppoaIntervalTable 1.3.6.1.4.1.9.9.154.1.17
This table contains PPPoA statistics intervals for those ITU-C class devices configured for PPP operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIdslPppoaIntervalEntry

cIdslPppoaIntervalEntry 1.3.6.1.4.1.9.9.154.1.17.1
A 15-minute interval of PPPoA statistics intervals for a ITU-C class device configured for PPP operation. There exists up to 96 entries for each ifEntry that meets the following criteria: 1) The ifEntry has an ifType of idsl(154); 2) The profile associated with the ITU-C class device specifies a value of 'ppp' for the cIdslLineProtocol object.
Status: current Access: not-accessible
OBJECT-TYPE    
  CIdslPppoaIntervalEntry  

cIdslPppoaIntervalNumber 1.3.6.1.4.1.9.9.154.1.17.1.1
The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval collected 24 hours ago. Intervals 2..96 are optional.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

cIdslPppoaIntervalValidData 1.3.6.1.4.1.9.9.154.1.17.1.2
This object specifies whether the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cIdslPppoaIntervalRTOs 1.3.6.1.4.1.9.9.154.1.17.1.3
This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslPppoaIntervalCVs 1.3.6.1.4.1.9.9.154.1.17.1.4
This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslPppoaIntervalShorts 1.3.6.1.4.1.9.9.154.1.17.1.5
This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslPppoaIntervalLongs 1.3.6.1.4.1.9.9.154.1.17.1.6
This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslPppoaIntervalDiscards 1.3.6.1.4.1.9.9.154.1.17.1.7
This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

cIdslPppoaMapTable 1.3.6.1.4.1.9.9.154.1.18
This table defines the mapping between PPP sessions and ATM VC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CIdslPppoaMapEntry

cIdslPppoaMapEntry 1.3.6.1.4.1.9.9.154.1.18.1
A mapping between a PPP session and an ATM VC. There exists an entry for each ifEntry that meet the following criteria: 1) The ifEntry has an ifType of idsl(154); 2) The profile associated with the ITU-C class device specifies a value of 'ppp' for the cIdslLineProtocol object.
Status: current Access: not-accessible
OBJECT-TYPE    
  CIdslPppoaMapEntry  

cIdslPppoaMapIfIndex 1.3.6.1.4.1.9.9.154.1.18.1.1
The ifIndex associated with the pseudo-ATM interface onto which the IDSL interface is being mapped.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

cIdslPppoaMapVpi 1.3.6.1.4.1.9.9.154.1.18.1.2
The VPI (Virtual Path Identifier) associated with the ATM VCL onto which the PPP session is being mapped.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4095  

cIdslPppoaMapVci 1.3.6.1.4.1.9.9.154.1.18.1.3
The VCI (Virtual Circuit Identifier) associated with the ATM VCL onto which the PPP session is being mapped.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

ciscoIdslLineMIBNotificationsPrefix 1.3.6.1.4.1.9.9.154.2
OBJECT IDENTIFIER    

ciscoIdslLineMIBNotifications 1.3.6.1.4.1.9.9.154.2.0
OBJECT IDENTIFIER    

ciscoIdslLineMIBConformance 1.3.6.1.4.1.9.9.154.3
OBJECT IDENTIFIER    

ciscoIdslLineMIBCompliances 1.3.6.1.4.1.9.9.154.3.1
OBJECT IDENTIFIER    

ciscoIdslLineMIBGroups 1.3.6.1.4.1.9.9.154.3.2
OBJECT IDENTIFIER    

ciscoIdslLineMIBCompliance 1.3.6.1.4.1.9.9.154.3.1.1
The compliance statement for entities that implement the CISCO-IDSL-LINE-MIB. Implementation of this MIB is mandatory for any platform that supports one or more IDSL line interfaces.
Status: current Access: read-write
MODULE-COMPLIANCE    

cIdslBasicGroup 1.3.6.1.4.1.9.9.154.3.2.1
A collection of managed objects defining the basic operation of an IDSL line.
Status: current Access: read-write
OBJECT-GROUP    

cIdslPM15MinIntervalGroup 1.3.6.1.4.1.9.9.154.3.2.2
A collection of managed objects defining performance data collection capability using 15-minute intervals.
Status: current Access: read-write
OBJECT-GROUP