CISCO-INTERFACE-XCVR-MONITOR-MIB

File: CISCO-INTERFACE-XCVR-MONITOR-MIB.mib (10865 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF IF-MIB
SNMPv2-TC CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP
ifName TEXTUAL-CONVENTION ciscoMgmt

Defined Types

CiscoInterfaceXcvrMonitorStatus  
This textual convention defines the status of the monitoring parameter for a given sensor type in transceiver digital diagnostics on an interface. The value of the monitoring parameter for a given sensor lies are bounded within maximum (high) and minimum (low) limits. If the current value is over the high limit, this status is set to 'highSet'. Upon the value of the sensor coming back into the normal range (between high and low values), this status is set to 'highClear'. Similarly, if the current value is below the low limit, this status is set to 'lowSet'. Upon the value the sensor coming back into normal range subsequently, this status is set to 'lowClear'. If the current value is stays within the high and low limits, this status is set to 'normal'. Also, subsequently after the status had been either 'highClear' or 'lowClear', if the value is within the high and low limits, this status is set to 'normal'.
TEXTUAL-CONVENTION    
  INTEGER highSet(1), lowSet(2), highClear(3), lowClear(4), normal(5)  

Defined Values

ciscoInterfaceXcvrMonitorMIB 1.3.6.1.4.1.9.9.706
A MIB module that provides monitoring information about the transceivers plugged into interface on a system.
MODULE-IDENTITY    

ciscoInterfaceXcvrMonMIBNotifs 1.3.6.1.4.1.9.9.706.0
OBJECT IDENTIFIER    

ciscoInterfaceXcvrMonMIBObjects 1.3.6.1.4.1.9.9.706.1
OBJECT IDENTIFIER    

ciscoInterfaceXcvrMonMIBConform 1.3.6.1.4.1.9.9.706.2
OBJECT IDENTIFIER    

cIfXcvrMonDigitalDiagTempAlarm 1.3.6.1.4.1.9.9.706.1.1
The current status of temperature alarm flag on the temperature sensor of the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonDigitalDiagTempWarning 1.3.6.1.4.1.9.9.706.1.2
The current status of temperature warning flag on the temperature sensor of the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonDigitalDiagVoltAlarm 1.3.6.1.4.1.9.9.706.1.3
The current status of voltage alarm flag on the voltage sensor of the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonDigitalDiagVoltWarning 1.3.6.1.4.1.9.9.706.1.4
The current status of voltage warning flag on the voltage sensor of the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonDigitalDiagCurrAlarm 1.3.6.1.4.1.9.9.706.1.5
The current status of current alarm flag on the current sensor of the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonDigitalDiagCurrWarning 1.3.6.1.4.1.9.9.706.1.6
The current status of current warning flag on the current sensor of the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonDigitalDiagRxPwrAlarm 1.3.6.1.4.1.9.9.706.1.7
The current status of Rx power alarm flag on the Rx power sensor of the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonDigitalDiagRxPwrWarning 1.3.6.1.4.1.9.9.706.1.8
The current status of Rx power warning flag on the Rx power sensor of the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonDigitalDiagTxPwrAlarm 1.3.6.1.4.1.9.9.706.1.9
The current status of Tx power alarm flag on the Tx power sensor of the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonDigitalDiagTxPwrWarning 1.3.6.1.4.1.9.9.706.1.10
The current status of Tx power warning flag on the Tx power sensor of the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonDigitalDiagTxFaultAlarm 1.3.6.1.4.1.9.9.706.1.11
The current status of Tx fault count flag on the transceiver in the interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CiscoInterfaceXcvrMonitorStatus  

cIfXcvrMonStatusChangeNotifEnable 1.3.6.1.4.1.9.9.706.1.12
Indicates whether cIfXcvrMonStatusChangeNotif should be generated.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

cIfXcvrMonStatusChangeNotif 1.3.6.1.4.1.9.9.706.0.1
This notification trap indicates the current status of the alarm and warning monitoring parameters for all the sensors based on the digital diagnostic monitoring information. This notification is generated whenever there is a change in the status of atleast one of the monitoring parameters of the sensors on the transceiver in an interface.
Status: current Access: read-write
NOTIFICATION-TYPE    

ciscoInterfaceXcvrMonMIBCompliances 1.3.6.1.4.1.9.9.706.2.1
OBJECT IDENTIFIER    

ciscoInterfaceXcvrMonMIBGroups 1.3.6.1.4.1.9.9.706.2.2
OBJECT IDENTIFIER    

cIfXcvrMonMIBCompliance 1.3.6.1.4.1.9.9.706.2.1.1
This is a default module-compliance containing default object groups.
Status: current Access: read-only
MODULE-COMPLIANCE    

cIfXcvrDigitalDiagMonStatusGroup 1.3.6.1.4.1.9.9.706.2.2.1
A collection of Cisco specific Digital Diagnostics monitoring status information.
Status: current Access: read-only
OBJECT-GROUP    

cIfXcvrMonStatusChangeNotifGroup 1.3.6.1.4.1.9.9.706.2.2.2
A collection of Cisco specific Digital Diagnostics monitoring notifications.
Status: current Access: read-only
NOTIFICATION-GROUP