CISCO-IVR-MIB

File: CISCO-IVR-MIB.mib (107459 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
CISCO-SMI SNMP-FRAMEWORK-MIB CISCO-VSAN-MIB
CISCO-ZS-MIB CISCO-ST-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Integer32 Unsigned32 MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP TEXTUAL-CONVENTION
RowStatus TruthValue TimeStamp
ciscoMgmt SnmpAdminString vsanIndex
FcList ZoneQosPriorityLevel VsanIndex
FcNameId DomainId FcAddressId

Defined Types

CIvrZoneMemberType  
Type of IV zone member. pwwnVsan - the member is identified by port WWN (World Wide Name) and VSAN.
TEXTUAL-CONVENTION    
  INTEGER pwwnVsan(1)  

CIvrAutonomousFabricId  
The Autonomous Fabric identifier. This identifies a set of fibre channel devices like hosts, disks, switches which are under single administration. It is up to the administrator to assign these identifiers to the Autonomous Fabrics so that each of the physical fabrics are uniquely identified. If a fabric is not partitioned into Autonomous Fabrics, then value of 1 must be used.
TEXTUAL-CONVENTION    
  Unsigned32 1..65535  

CIvrChecksum  
The checksum computed from the object/group of objects specified in the object description. This is used by manager to check if the object or group of objects is same across devices in the fabric. Note that method use to compute this is implementation specific.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..255)  

CivrZoneSetEntry  
SEQUENCE    
  civrZoneSetIndex Unsigned32
  civrZoneSetName SnmpAdminString
  civrZoneSetZoneList FcList
  civrZoneSetLastChange TimeStamp
  civrZoneSetChecksum CIvrChecksum
  civrZoneSetRowStatus RowStatus

CivrZoneEntry  
SEQUENCE    
  civrZoneIndex Unsigned32
  civrZoneName SnmpAdminString
  civrZoneMemberList FcList
  civrZoneLastChange TimeStamp
  civrZoneRowStatus RowStatus
  civrZoneReadOnly TruthValue
  civrZoneQosPriority ZoneQosPriorityLevel

CivrZoneMemberEntry  
SEQUENCE    
  civrZoneMemberParentIndex Unsigned32
  civrZoneMemberIndex Unsigned32
  civrZoneMemberType CIvrZoneMemberType
  civrZoneMemberID OCTET STRING
  civrZoneMemberAFId CIvrAutonomousFabricId
  civrZoneMemberVsan VsanIndex
  civrZoneMemberRowStatus RowStatus
  civrZoneMemberLunID OCTET STRING

CivrZoneEnforcedZoneEntry  
SEQUENCE    
  civrZoneEnforcedZoneName SnmpAdminString
  civrZoneEnforcedZoneMemberList FcList
  civrZoneEnforcedZoneReadOnly TruthValue
  civrZoneEnforcedZoneQosPriority ZoneQosPriorityLevel

CivrZoneEnforcedZoneMemberEntry  
SEQUENCE    
  civrZoneEnforcedZoneMemberType CIvrZoneMemberType
  civrZoneEnforcedZoneMemberID OCTET STRING
  civrZoneEnforcedZoneMemberAFId CIvrAutonomousFabricId
  civrZoneEnforcedZoneMemberVsan VsanIndex
  civrZoneEnforcedZoneMemberLunID OCTET STRING

CivrZoneSetStatusEntry  
SEQUENCE    
  civrZoneSetStatus INTEGER

CivrTopologyConfigEntry  
SEQUENCE    
  civrTopologyConfigSwitchWwn FcNameId
  civrTopologyConfigAutoFabricId CIvrAutonomousFabricId
  civrTopologyConfigSwitchVsan2k FcList
  civrTopologyConfigSwitchVsan4k FcList
  civrTopologyConfigRowStatus RowStatus

CivrTopologyActiveEntry  
SEQUENCE    
  civrTopologyActiveSwitchWwn FcNameId
  civrTopologyActiveAutoFabricId CIvrAutonomousFabricId
  civrTopologyActiveSwitchVsan2k FcList
  civrTopologyActiveSwitchVsan4k FcList

CivrTopologyAfidConfEntry  
SEQUENCE    
  civrTopologyAfidConfSwitchWwn FcNameId
  civrTopologyAfidConfId CIvrAutonomousFabricId
  civrTopologyAfidConfSwitchVsan2k FcList
  civrTopologyAfidConfSwitchVsan4k FcList
  civrTopologyAfidConfRowStatus RowStatus

CivrTopologyDefaultAfidEntry  
SEQUENCE    
  civrTopologyDefaultAfidSwitchWwn FcNameId
  civrTopologyDefaultAfidId CIvrAutonomousFabricId
  civrTopologyDefaultAfidStatus RowStatus

CivrTopologyIvrSrvGrpEntry  
SEQUENCE    
  civrTopologyIvrSrvGrpName SnmpAdminString
  civrTopologyIvrSrvGrpVsan2k FcList
  civrTopologyIvrSrvGrpVsan4k FcList
  civrTopologyIvrSrvGrpRowStatus RowStatus

CivrEnabledDeviceEntry  
SEQUENCE    
  civrEnabledDeviceVsan VsanIndex
  civrEnabledDeviceAutoFabricId CIvrAutonomousFabricId
  civrEnabledDeviceDomainId DomainId
  civrEnabledDeviceSwitchWwn FcNameId
  civrEnabledDeviceCapability BITS

Defined Values

ciscoIvrMIB 1.3.6.1.4.1.9.9.371
The MIB module for the management of Inter-VSAN routing within the framework of Cisco's Inter-VSAN Routing (IVR) Architecture. IVR allows traffic between VSANs. VSANs are logically separated Storage Area Networks (SANs) where traffic does not cross VSAN boundaries. Certain SAN applications need restricted communication between initiators and targets which are in different VSANs. This MIB enables the users to manage IVR. The VSANs logically separate a single physical fabric into multiple logical fabrics. Each of these physical fabrics are called Autonmous Fabrics. In addition to Inter-VSAN communication, IVR also enables communication between Autonomous Fabrics. Acronyms The following acronyms are used in this document: Lun: Logical Unit Number IV: Inter-VSAN IVR: Inter-VSAN Routing PWWN: Port World Wide Name AFID: Autonomous Fabric id
MODULE-IDENTITY    

ciscoIvrMIBNotifications 1.3.6.1.4.1.9.9.371.0
OBJECT IDENTIFIER    

ciscoIvrMIBObjects 1.3.6.1.4.1.9.9.371.1
OBJECT IDENTIFIER    

ciscoIvrMIBConformance 1.3.6.1.4.1.9.9.371.2
OBJECT IDENTIFIER    

cimIvrConfiguration 1.3.6.1.4.1.9.9.371.1.1
OBJECT IDENTIFIER    

cimIvrStats 1.3.6.1.4.1.9.9.371.1.2
OBJECT IDENTIFIER    

cimIvrGeneric 1.3.6.1.4.1.9.9.371.1.1.1
OBJECT IDENTIFIER    

cimIvrZoneset 1.3.6.1.4.1.9.9.371.1.1.2
OBJECT IDENTIFIER    

cimIvrZone 1.3.6.1.4.1.9.9.371.1.1.3
OBJECT IDENTIFIER    

cimIvrZoneMember 1.3.6.1.4.1.9.9.371.1.1.4
OBJECT IDENTIFIER    

cimIvrTopology 1.3.6.1.4.1.9.9.371.1.1.5
OBJECT IDENTIFIER    

cimIvrVirtualDomains 1.3.6.1.4.1.9.9.371.1.1.6
OBJECT IDENTIFIER    

civrFcidNatMode 1.3.6.1.4.1.9.9.371.1.1.1.1
Enable FCID and VSAN identifier translation cross VSAN boundaries. If the value is 'true', the VSAN identifier as well as the entire FCID of the end-devices would be modified as frames cross VSAN boundaries.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

civrVsanTopologyAutoDisc 1.3.6.1.4.1.9.9.371.1.1.1.2
Enable automatic VSAN topology discovery. If this value is 'true', automatic VSAN topology discovery is turned on. IVR processes would communicate with each other to provide a global view of the physical topology to all the IVR enabled switches. VSAN topology is configured through civrTopologyAfidConfTable and civrTopologyDefaultAfidTable when automatic VSAN topology discovery is turned on. If this value is 'false', automatic VSAN topology discovery is turned off. VSAN topology is manually configured by using civrTopologyConfigTable.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

civrZoneSetNumber 1.3.6.1.4.1.9.9.371.1.1.2.1
The number of entries currently present in the civrZoneSetTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..8388608  

civrZoneSetTable 1.3.6.1.4.1.9.9.371.1.1.2.2
A table containing information on each Inter-VSAN (IV) zonesets which are configured locally. It comprises the zonesets in the full IV zone database. There could be multiple IV zonesets configured. But only one zoneset is allowed to be active at a time. An IV zoneset is a collection of IV zones.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrZoneSetEntry

civrZoneSetEntry 1.3.6.1.4.1.9.9.371.1.1.2.2.1
An entry (conceptual row) in the civrZoneSetTable. The sequence of operations to be performed in order to create a zoneset is as follows: - create zone entries in the civrZoneTable. - create an entry in this table and set the civrZoneSetZoneList bitmap object to contain the required IV zones. - Note that it is perfectly valid to create an empty zoneset.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrZoneSetEntry  

civrZoneSetIndex 1.3.6.1.4.1.9.9.371.1.1.2.2.1.1
The index of a zoneset. This object uniquely identifies an IV zoneset. This object could have the same value as civrZoneSetTableNextIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..2048  

civrZoneSetName 1.3.6.1.4.1.9.9.371.1.1.2.2.1.2
The name of this zoneset. The civrZoneSetName should be unique on this device. This object cannot be modified while the corresponding value of civrZoneSetRowStatus is equal to 'active'. This object MUST be set before or concurrently with setting the corresponding instance of civrZoneSetRowStatus to 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..64)  

civrZoneSetZoneList 1.3.6.1.4.1.9.9.371.1.1.2.2.1.3
The set of IV zones which form this zoneset. The IV zones are identified by civrZoneIndex object in the civrZoneTable. If a particular bit has a value of '1', then the corresponding zone is a part of this zoneset. All other zones have '0' in their positions or not present in the string. Note that an IV zone can be part of multiple IV zonesets.
Status: current Access: read-create
OBJECT-TYPE    
  FcList  

civrZoneSetLastChange 1.3.6.1.4.1.9.9.371.1.1.2.2.1.4
The value of sysUpTime at the time of the last change to this IV zoneset entry. If the entry has not been modified since the last re-initialization of the local network management system, then this object will contain a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

civrZoneSetChecksum 1.3.6.1.4.1.9.9.371.1.1.2.2.1.5
The checksum of content of this zoneset.
Status: current Access: read-only
OBJECT-TYPE    
  CIvrChecksum  

civrZoneSetRowStatus 1.3.6.1.4.1.9.9.371.1.1.2.2.1.6
The status of this conceptual row. This object can not be set to 'active' unless the corresponding value of civrZoneSetName is unique.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

civrZoneSetActivate 1.3.6.1.4.1.9.9.371.1.1.2.3
Setting this object to a value is a request for a particular IV zoneset to be activated on this device. i.e., for the current configuration of that zoneset to be cloned with the clone becoming the active zoneset. Setting this object to a value (say, N) identifies the IV zoneset to be cloned as the zoneset identified by civrZoneSetIndex object having the same value N. Even though there could be multiple IV zonesets on this device, only one can be active at a time. If a IV zoneset is already active and a second IV zone set is activated, then the first IV zoneset is automatically deactivated and the second IV zoneset is activated. The IV zoneset activation is done only in 'activate VSANs' on the local device. The 'activate VSANs' is the intersection of topology VSANs on the local device (civrTopologyActiveSwitchVsan2k and civrTopologyActiveSwitchVsan4k), members VSANs (union of all the VSANs of the members in the zoneset being activated) and local VSANs (vsanTable from CISCO-VSAN-MIB). If the activation was successful then, civrZoneEnforcedZoneSetName contains the name of zoneset corresponding to the civrZoneSetIndex that was set. The value of this object when read is always 0.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2048  

civrZoneSetActvatDeactvatResult 1.3.6.1.4.1.9.9.371.1.1.2.4
This object indicates the outcome of the most recent activation/deactivation. activateSuccess - activation success activateFailureNoMembers - activation failure because of no members in the zoneset activateFailureZoneOneorLessMem - activation failure as the zoneset being activated contained one or less member. activateFailureNoTopology - activation failure because of no IVR topology activateFailureNoPerVsanSucc - activation failed in all 'activate VSANs' activateFailureNoZoneset - activation failure because of no zoneset activateFailureNoVsans - activation failure because of no 'activate VSANs' activateFailureFabricUnstable - activation failure because fabric unstable deactivateSuccess - deactivation success deactivateFailureNoActiveZs - no active zoneseset deactivateFailureNoPerVsanSucc - deactivation failed in all 'activate VSANs' deactivateFailureFabricUnstable - deactivation failed because fabric is unstable activating - activation in progress deactivating - deactivation in progress idle - idle deactivateSuccessFcNatShutup13 - deactivation success, shutup 1.3 switch in NAT mode activateFailureFabric - none of the switches connected to the fabric is able to activate this zoneset deactivateFailureFabric - none of the switches connected to the fabric is able to deactivate this zoneset activatePartialSuccessFabric - activation succeeds on some of the switches connected to this fabric deactivatePartialSuccessFabric - deactivation succeeds on some of the switches connected to this fabric deviceCleanupInProgress - device cleanup is in progress during deactivation activatingReadyToAdv - switches connected to this fabric are ready to advertise device changes activatingAdvertising - switches connected to this fabric are advertising device change information When the value of this object is either 'activating', or 'deactivating', the values of of civrZoneSetActivate and civrZoneSetDeActivate respectively cannot be modified.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER activateSuccess(1), activateFailureNoMembers(2), activateFailureZoneOneorLessMem(3), activateFailureNoTopology(4), activateFailureNoPerVsanSucc(5), activateFailureNoZoneset(6), activateFailureNoVsans(7), activateFailureFabricUnstable(8), deactivateSuccess(9), deactivateFailureNoActiveZs(10), deactivateFailureNoPerVsanSucc(11), deactivateFailureFabricUnstable(12), activating(13), deactivating(14), idle(15), deactivateSuccessFcNatShutup13(16), activateFailureFabric(17), deactivateFailureFabric(18), activatePartialSuccessFabric(19), deactivatePartialSuccessFabric(20), deviceCleanupInProgress(21), activatingReadyToAdv(22), activatingAdvertising(23)  

civrZoneSetDeActivate 1.3.6.1.4.1.9.9.371.1.1.2.5
Setting this object to 'deactivate' is a request to deactivate the currently active IV zoneset. deactivate - deactivate IV zoneset noop - no operation No action is taken if this object is set to 'noop'. The value of this object when read is always 'noop'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER deactivate(1), noop(2)  

civrZonesetDbChecksum 1.3.6.1.4.1.9.9.371.1.1.2.6
The checksum of the full IV zone database.
Status: current Access: read-only
OBJECT-TYPE    
  CIvrChecksum  

civrActiveZonesetChecksum 1.3.6.1.4.1.9.9.371.1.1.2.7
The checksum of the enforced (active) IV zoneset.
Status: current Access: read-only
OBJECT-TYPE    
  CIvrChecksum  

civrZoneNumber 1.3.6.1.4.1.9.9.371.1.1.3.1
The number of entries currently present in the civrZoneTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

civrZoneTable 1.3.6.1.4.1.9.9.371.1.1.3.2
This table gives information on all the IV zones and lists all their members. IV zones is group of IV members (FC devices like hosts, disks) in different VSANs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrZoneEntry

civrZoneEntry 1.3.6.1.4.1.9.9.371.1.1.3.2.1
An entry (conceptual row) in the civrZoneTable. These are the zones in the full IV zone database. The sequence of operations to be performed in order to create a IV Zone is as follows: - create an entry in this table. - create IV zone members in the civrZoneMemberTable that belong to this IV zone.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrZoneEntry  

civrZoneIndex 1.3.6.1.4.1.9.9.371.1.1.3.2.1.1
The index of an IV Zone. This object could have the same value as civrZoneTableNextIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..2048  

civrZoneName 1.3.6.1.4.1.9.9.371.1.1.3.2.1.2
The name of this zone. The zoneName should be unique this device. This object can not be modified while the corresponding value of civrZoneRowStatus is 'active'. This object MUST be set before or concurrently with setting the corresponding instance of civrZoneRowStatus to 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..58)  

civrZoneMemberList 1.3.6.1.4.1.9.9.371.1.1.3.2.1.3
The set of IV Zone members that form this IV zone. The IV zone members are identified by civrZoneMemberIndex object in the civrZoneMemberTable. If a particular bit has a value of '1', then the corresponding zone member is a part of this zone. All other zone members have '0' in their positions or not present in the string. This object is read-only; changes to its value are made by the agent as and when associated entries are created/deleted in the civrZoneMemberTable. The default value is the zero length string.
Status: current Access: read-only
OBJECT-TYPE    
  FcList  

civrZoneLastChange 1.3.6.1.4.1.9.9.371.1.1.3.2.1.5
The value of sysUpTime at the time of the last change to this IV zone entry. If the entry has not been modified since the last re-initialization of the local network management system, then this object will contain a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

civrZoneRowStatus 1.3.6.1.4.1.9.9.371.1.1.3.2.1.6
The status of this conceptual row. This object can not be set to 'active' unless the corresponding value of zoneName is unique on this device.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

civrZoneReadOnly 1.3.6.1.4.1.9.9.371.1.1.3.2.1.7
This object indicates if only SCSI read operations are allowed on members of this IV zone which are SCSI targets. If this object is set to 'true', then only SCSI read operations are permitted. So, this IV zone becomes a read-only IV zone. If this object is set to 'false', then both SCSI read and write operations are permitted in this IV zone.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

civrZoneQosPriority 1.3.6.1.4.1.9.9.371.1.1.3.2.1.8
This object specifies if qos attribute for this IV zone is enabled. If this object is set to a value other than 'none', then qos attribute for this IV zone is enabled. If this object is set to 'none', then qos attribute for this IV zone is disabled. If this attribute is enabled for this IV zone, then only traffic with the configured priority level will be allowed between the members of this IV zone.
Status: current Access: read-create
OBJECT-TYPE    
  ZoneQosPriorityLevel  

civrZoneMemberNumber 1.3.6.1.4.1.9.9.371.1.1.4.1
The number of entries currently present in the civrZoneMemberTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16777216  

civrZoneMemberTable 1.3.6.1.4.1.9.9.371.1.1.4.2
This table contains all members of all the IV Zones in the civrZoneTable and information about those members. These are the members part of full IV zone database.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrZoneMemberEntry

civrZoneMemberEntry 1.3.6.1.4.1.9.9.371.1.1.4.2.1
An entry (conceptual row) in the civrZoneMemberTable. Each entry represents the relationship between a member and (one of) its 'parent(s)', i.e., an IV zone to which the member belongs to.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrZoneMemberEntry  

civrZoneMemberParentIndex 1.3.6.1.4.1.9.9.371.1.1.4.2.1.1
This object contains the value of the index of the IV zone to which this member belongs to.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..2048  

civrZoneMemberIndex 1.3.6.1.4.1.9.9.371.1.1.4.2.1.2
The index of this IV zone member on this IV zone.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..2048  

civrZoneMemberType 1.3.6.1.4.1.9.9.371.1.1.4.2.1.3
The type of IV Zone member. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  CIvrZoneMemberType  

civrZoneMemberID 1.3.6.1.4.1.9.9.371.1.1.4.2.1.4
This object represents the IV zone member ID. If civrZoneMemberType is 'pwwnVsan', this object contains port WWN. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

civrZoneMemberAFId 1.3.6.1.4.1.9.9.371.1.1.4.2.1.5
The Autonomous Fabric identifier of this IV zone member. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  CIvrAutonomousFabricId  

civrZoneMemberVsan 1.3.6.1.4.1.9.9.371.1.1.4.2.1.6
The VSAN of this IV zone member. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  VsanIndex  

civrZoneMemberRowStatus 1.3.6.1.4.1.9.9.371.1.1.4.2.1.7
The status of this conceptual row. civrMemberType, civrZoneMemberID and civrZoneMemberVsan objects MUST be set before or concurrently with setting the corresponding instance of civrZoneMemberRowStatus to 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

civrZoneMemberLunID 1.3.6.1.4.1.9.9.371.1.1.4.2.1.8
This object specifies the Lun ID if IV Lun zoning is configured. If this object is the zero-length string, then IV Lun zoning is not configured. This object cannot be modified while the corresponding value of zoneMemberRowStatus object is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0|8)  

civrZoneEnforcedZoneSetName 1.3.6.1.4.1.9.9.371.1.1.2.8
The name of the enforced IV zoneset.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(1..64)  

civrZoneEnforcedZoneSetZoneList 1.3.6.1.4.1.9.9.371.1.1.2.9
The set of IV zones which form this IV zoneset. This object was copied from the civrZoneSetZoneList object in the civrZoneSetTable at the time when the currently active zoneset was activated.
Status: current Access: read-only
OBJECT-TYPE    
  FcList  

civrZoneEnforcedZoneSetActvtTime 1.3.6.1.4.1.9.9.371.1.1.2.10
The sysUpTime at which enforced zoneset was most recently activated. If this entry has been activated prior to the last re-initialization of the local network management system, then this object will contain a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

civrZoneCopyZoneSetEnforcdToFull 1.3.6.1.4.1.9.9.371.1.1.2.11
This object copies the enforced IV zoneset (active IV zoneset) into the full IV zone database Setting this object to 'copy' will trigger the copy of the enforced IV zoneset to the full IV zone database. If there is no enforced IV zoneset, the copy will result in an error. No action is taken if this object is set to 'noOp'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER copy(1), noOp(2)  

civrZoneClearFullZoneDb 1.3.6.1.4.1.9.9.371.1.1.2.12
This object clears the full IVR zone database. Setting this object to 'clear' will clear the full IV zone database. No action is taken if this object is set to 'noOp'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clear(1), noOp(2)  

civrZonesetActivateForce 1.3.6.1.4.1.9.9.371.1.1.2.13
The force option for IV zoneset activation. Following things are done if this object is 'true': - If there is no regular active zoneset in a VSAN (no entry present zoneEnforcedZoneSetTable from CISCO-ZS-MIB for that VSAN), then a regular active zoneset will be created and the IV zones will be added to the active zoneset. - if the default zone behaviour (as indicated by object zoneDefaultZoneBehaviour from CISCO-ZS-MIB) is 'permit', then the IV zones will be added to the regular active zoneset. If the value of this object is 'false', the IV zones are added to the regular active zoneset only in the case of default zone behaviour is 'deny'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

civrZoneSetTableNextIndex 1.3.6.1.4.1.9.9.371.1.1.2.14
This object specifies the next available index for object civrZoneSetIndex which can be used for creating an entry in civrZoneSetTable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

civrZoneEnforcedZoneNumber 1.3.6.1.4.1.9.9.371.1.1.3.3
The number of entries currently present in the civrZoneEnforcedZoneTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..8388608  

civrZoneEnforcedZoneTable 1.3.6.1.4.1.9.9.371.1.1.3.4
This table contains all the IV zones that are present in the active IV zoneset.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrZoneEnforcedZoneEntry

civrZoneEnforcedZoneEntry 1.3.6.1.4.1.9.9.371.1.1.3.4.1
An entry (conceptual row) in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrZoneEnforcedZoneEntry  

civrZoneEnforcedZoneName 1.3.6.1.4.1.9.9.371.1.1.3.4.1.1
The name of this zone.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(1..58)  

civrZoneEnforcedZoneMemberList 1.3.6.1.4.1.9.9.371.1.1.3.4.1.2
The set of members that form this IV zone. This object was copied from the civrZoneMemberList object in the civrZoneTable at the time when the currently active zoneset was activated.
Status: current Access: read-only
OBJECT-TYPE    
  FcList  

civrZoneEnforcedZoneReadOnly 1.3.6.1.4.1.9.9.371.1.1.3.4.1.3
This object indicates whether this is a read-only IV zone. This object was copied from the civrZoneReadOnly object in the civrZoneTable at the time when the currently active zoneset was activated.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

civrZoneEnforcedZoneQosPriority 1.3.6.1.4.1.9.9.371.1.1.3.4.1.4
This object indicates whether this is a qos enabled IV zone. This object was copied from the civrZoneQosPriority object in the civrZoneTable at the time when the currently active zoneset was activated.
Status: current Access: read-only
OBJECT-TYPE    
  ZoneQosPriorityLevel  

civrZoneTableNextIndex 1.3.6.1.4.1.9.9.371.1.1.3.5
This object specifies the next available index for object civrZoneIndex which can be used for creating an entry in civrZoneTable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

civrZoneEnforcedZoneMemberNumber 1.3.6.1.4.1.9.9.371.1.1.4.3
The number of entries currently present in the civrZoneEnforcedZoneMemberTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16777216  

civrZoneEnforcedZoneMemberTable 1.3.6.1.4.1.9.9.371.1.1.4.4
This table contains all members that are part of a IV zone and are part of the active IV zone set.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrZoneEnforcedZoneMemberEntry

civrZoneEnforcedZoneMemberEntry 1.3.6.1.4.1.9.9.371.1.1.4.4.1
An entry (conceptual row) in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrZoneEnforcedZoneMemberEntry  

civrZoneEnforcedZoneMemberType 1.3.6.1.4.1.9.9.371.1.1.4.4.1.2
The type of IV zone member. This object was copied from the civrZoneMemberType object in the civrZoneMemberTable at the time when the currently active zoneset was activated.
Status: current Access: read-only
OBJECT-TYPE    
  CIvrZoneMemberType  

civrZoneEnforcedZoneMemberID 1.3.6.1.4.1.9.9.371.1.1.4.4.1.3
This object represents this member's address. This object was copied from the civrZoneMemberID object in the civrZoneMemberTable at the time when the currently active zoneset was activated.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

civrZoneEnforcedZoneMemberAFId 1.3.6.1.4.1.9.9.371.1.1.4.4.1.4
The Autonomous Fabric identifier of the member. This object was copied from the civrZoneMemberAFId object in the civrZoneMemberTable at the time when the currently active zoneset was activated.
Status: current Access: read-only
OBJECT-TYPE    
  CIvrAutonomousFabricId  

civrZoneEnforcedZoneMemberVsan 1.3.6.1.4.1.9.9.371.1.1.4.4.1.5
The VSAN of the member. This object was copied from the civrZoneMemberVsan object in the civrZoneMemberTable at the time when the currently active zoneset was activated.
Status: current Access: read-only
OBJECT-TYPE    
  VsanIndex  

civrZoneEnforcedZoneMemberLunID 1.3.6.1.4.1.9.9.371.1.1.4.4.1.6
This object specifies the Lun ID if IV Lun zoning is configured. This object was copied from the civrZoneMemberLunID object in the civrZoneMemberTable at the time when the currently active zoneset was activated.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0|8)  

civrZoneSetStatusTable 1.3.6.1.4.1.9.9.371.1.2.1
A table containing status of the current active IV Zoneset on each local VSANs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrZoneSetStatusEntry

civrZoneSetStatusEntry 1.3.6.1.4.1.9.9.371.1.2.1.1
An entry (conceptual row) in the civrZoneSetStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrZoneSetStatusEntry  

civrZoneSetStatus 1.3.6.1.4.1.9.9.371.1.2.1.1.1
Status of the active IV Zoneset on this VSAN. idle - idle active - active deactive - deactive defaultZoneDeny - activation failed because of default zone behaviour is deny and there is no regular active zoneset. activationFailed - activation failed (check zoneSetFailCause in CISCO-ZS-MIB for this VSAN) deactivationFailed - deactivation failed (check zoneSetFailCause in CISCO-ZS-MIB for this VSAN) activationNotInitiated - activation not initiated activationFailedFabricChgFailed - activation failed because of fabric change failed deactivationNotInitiated - deactivation not initiated deactivationFailedFabChgFailed - deactivation failed because of fabric changing activating - activation in progress activatingWaitForLowestSwwn - activation in progress; waiting for the lowest switch WWN switch to add IV zoneset to the regular active zoneset. activatingFabricChanging - activation in progress; fabric is changing deactivating - deactivation in progress deactivatingWaitForLowestSwwn - deactivation in progress; waiting for the lowest switch WWN switch to delete IV zoneset from the regular active zoneset. deactivatingFabricChanging - deactivation in progress; fabric is changing defaultZonePermit - activation failed because of default zone behaviour is permit defaultZonePermitNoForce - activation failed because of default zone behaviour is permit with no force option defaultZonePermitActZsNoForce - activation failed because of default zone behaviour is permit and with regular activate zoneset and no force option denyNoActiveZoneset - activation failed because there is no active zoneset activationFailedLowestWwnWait - activation failed waiting for switch with lowest wwn to activate this zoneset deactivationFailedLowestWwnWait - deactivation failed waiting for switch with lowest wwn to deactivate this zoneset .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER idle(1), active(2), deactive(3), defaultZoneDeny(4), activationFailed(5), deactivationFailed(6), activationNotInitiated(7), activationFailedFabricChgFailed(8), deactivationNotInitiated(9), deactivationFailedFabChgFailed(10), activating(11), activatingWaitForLowestSwwn(12), activatingFabricChanging(13), deactivating(14), deactivatingWaitForLowestSwwn(15), deactivatingFabricChanging(16), defaultZonePermit(17), defaultZonePermitNoForce(18), defaultZonePermitActZsNoForce(19), denyNoActiveZoneset(20), activationFailedLowestWwnWait(21), deactivationFailedLowestWwnWait(22)  

civrTopologyConfiguredChecksum 1.3.6.1.4.1.9.9.371.1.1.5.1
The checksum of the configured IVR topology.
Status: current Access: read-only
OBJECT-TYPE    
  CIvrChecksum  

civrTopologyConfigTable 1.3.6.1.4.1.9.9.371.1.1.5.2
This table contains the configured IVR topology. The topology is specified in terms of one or more Autonomous Fabrics made of switches and the VSANs to/from which the switches provide connectivity. The configured topology is not applied until it is made active using using object civrTopologyActivate.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrTopologyConfigEntry

civrTopologyConfigEntry 1.3.6.1.4.1.9.9.371.1.1.5.2.1
An entry (conceptual row) in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrTopologyConfigEntry  

civrTopologyConfigSwitchWwn 1.3.6.1.4.1.9.9.371.1.1.5.2.1.1
The configured switch WWN of this device.
Status: current Access: not-accessible
OBJECT-TYPE    
  FcNameId  

civrTopologyConfigAutoFabricId 1.3.6.1.4.1.9.9.371.1.1.5.2.1.2
The configured Autonomous Fabric id of this device.
Status: current Access: not-accessible
OBJECT-TYPE    
  CIvrAutonomousFabricId  

civrTopologyConfigSwitchVsan2k 1.3.6.1.4.1.9.9.371.1.1.5.2.1.3
The list of configured VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyConfigSwitchVsan4k are zero-length string, then the IVR topology contains only the default VSAN.
Status: current Access: read-create
OBJECT-TYPE    
  FcList  

civrTopologyConfigSwitchVsan4k 1.3.6.1.4.1.9.9.371.1.1.5.2.1.4
The list of configured VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2047 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list. If the values of both this object and corresponding instance of civrTopologyConfigSwitchVsan2k are zero-length string, then the IVR topology contains only the default VSAN.
Status: current Access: read-create
OBJECT-TYPE    
  FcList  

civrTopologyConfigRowStatus 1.3.6.1.4.1.9.9.371.1.1.5.2.1.5
Status of this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

civrTopologyActivate 1.3.6.1.4.1.9.9.371.1.1.5.3
Setting this object to 'activate' is a request for the configured IVR topology to be activated on this device. i.e., for the current configuration of IVR topology to be cloned, with the clone becoming the active IVR topology (civrTopologyActiveTable). The value of this object when read is always 'noOp'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER activate(1), noOp(2)  

civrTopologyActivateTime 1.3.6.1.4.1.9.9.371.1.1.5.4
The sysUpTime at which the IVR topology was most recently activated. If the IVR topology has not been activated prior to the last re-initialization of the local network management system, then this object will contain a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

civrTopologyCopyActiveToConfig 1.3.6.1.4.1.9.9.371.1.1.5.5
This object copies the active IVR topology table to configured IVR topology table. If there is no active IVR topology, the copy will result in an error. No action is taken if this object is set to 'noOp'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER copy(1), noOp(2)  

civrTopologyClearConfigured 1.3.6.1.4.1.9.9.371.1.1.5.6
This object clears the configured IVR topology table. No action is taken if this object is set to 'noOp'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clear(1), noOp(2)  

civrTopologyActiveChecksum 1.3.6.1.4.1.9.9.371.1.1.5.7
The checksum of the active IVR topology.
Status: current Access: read-only
OBJECT-TYPE    
  CIvrChecksum  

civrTopologyActiveTable 1.3.6.1.4.1.9.9.371.1.1.5.8
This table contains the IVR topology. The topology is specified in terms of one or more Autonomous Fabrics made of switches and the VSANs to/from which the switches provide connectivity.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrTopologyActiveEntry

civrTopologyActiveEntry 1.3.6.1.4.1.9.9.371.1.1.5.8.1
An entry (conceptual row) in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrTopologyActiveEntry  

civrTopologyActiveSwitchWwn 1.3.6.1.4.1.9.9.371.1.1.5.8.1.1
The switch WWN of this device.
Status: current Access: not-accessible
OBJECT-TYPE    
  FcNameId  

civrTopologyActiveAutoFabricId 1.3.6.1.4.1.9.9.371.1.1.5.8.1.2
The Autonomous Fabric id of this device.
Status: current Access: not-accessible
OBJECT-TYPE    
  CIvrAutonomousFabricId  

civrTopologyActiveSwitchVsan2k 1.3.6.1.4.1.9.9.371.1.1.5.8.1.3
The list of VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyActiveSwitchVsan4k are zero-length string, then the IVR topology contains only the default VSAN.
Status: current Access: read-only
OBJECT-TYPE    
  FcList  

civrTopologyActiveSwitchVsan4k 1.3.6.1.4.1.9.9.371.1.1.5.8.1.4
The list of VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2047 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list. If the values of both this object and corresponding instance of civrTopologyActiveSwitchVsan2k are zero-length string, then the IVR topology contains only the default VSAN.
Status: current Access: read-only
OBJECT-TYPE    
  FcList  

civrTopologyActive 1.3.6.1.4.1.9.9.371.1.1.5.9
This object indicates of IVR topology is active or not. If 'true', the IVR topology is active. And if it is 'false', the IVR topology is not active.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

civrTopologyAfidConfigChecksum 1.3.6.1.4.1.9.9.371.1.1.5.10
The checksum of the Autonomous Fabric id (AFID) configurations.
Status: current Access: read-only
OBJECT-TYPE    
  CIvrChecksum  

civrTopologyAfidConfTable 1.3.6.1.4.1.9.9.371.1.1.5.11
This table contains the Autonomous Fabric id (AFID) configurations when automatic VSAN topology discovery is activated. An entry (conceptual row) in this table represents an AFID and its VSANs on a switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrTopologyAfidConfEntry

civrTopologyAfidConfEntry 1.3.6.1.4.1.9.9.371.1.1.5.11.1
An entry (conceptual row) in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrTopologyAfidConfEntry  

civrTopologyAfidConfSwitchWwn 1.3.6.1.4.1.9.9.371.1.1.5.11.1.1
The switch WWN of this device.
Status: current Access: not-accessible
OBJECT-TYPE    
  FcNameId  

civrTopologyAfidConfId 1.3.6.1.4.1.9.9.371.1.1.5.11.1.2
The configured Autonomous Fabric id of this device.
Status: current Access: not-accessible
OBJECT-TYPE    
  CIvrAutonomousFabricId  

civrTopologyAfidConfSwitchVsan2k 1.3.6.1.4.1.9.9.371.1.1.5.11.1.3
The list of VSANs that are part of AFID (Autonomous Fabric ID) specified by civrTopologyConfigAutoFabricId on switch specified by civrTopologyConfigSwitchWwn. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this AFID on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyAfidConfSwitchVsan4k are zero-length string, then the AFID configured on this device contains only the default VSAN.
Status: current Access: read-create
OBJECT-TYPE    
  FcList  

civrTopologyAfidConfSwitchVsan4k 1.3.6.1.4.1.9.9.371.1.1.5.11.1.4
The list of VSANs that are part of AFID (Autonomous Fabric ID) specified by civrTopologyConfigAutoFabricId on switch specified by civrTopologyConfigSwitchWwn. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2048 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this AFID on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyAfidConfSwitchVsan2k are zero-length string, then the AFID configured on this device contains only the default VSAN.
Status: current Access: read-create
OBJECT-TYPE    
  FcList  

civrTopologyAfidConfRowStatus 1.3.6.1.4.1.9.9.371.1.1.5.11.1.5
Status of this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

civrTopologyDefaultAfidChecksum 1.3.6.1.4.1.9.9.371.1.1.5.12
The checksum of the configured default AFIDs.
Status: current Access: read-only
OBJECT-TYPE    
  CIvrChecksum  

civrTopologyDefaultAfidTable 1.3.6.1.4.1.9.9.371.1.1.5.13
This table contains the default Autonomous Fabric id (AFID) configurations when automatic VSAN topology discovery is activated. An entry (conceptual row) in this table represents the default AFID for a switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrTopologyDefaultAfidEntry

civrTopologyDefaultAfidEntry 1.3.6.1.4.1.9.9.371.1.1.5.13.1
An entry (conceptual row) in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrTopologyDefaultAfidEntry  

civrTopologyDefaultAfidSwitchWwn 1.3.6.1.4.1.9.9.371.1.1.5.13.1.1
The switch WWN of this device.
Status: current Access: not-accessible
OBJECT-TYPE    
  FcNameId  

civrTopologyDefaultAfidId 1.3.6.1.4.1.9.9.371.1.1.5.13.1.2
The configured Default Autonomous Fabric id of this switch.
Status: current Access: read-create
OBJECT-TYPE    
  CIvrAutonomousFabricId  

civrTopologyDefaultAfidStatus 1.3.6.1.4.1.9.9.371.1.1.5.13.1.3
Status of this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

civrTopologyIvrSrvGrpTable 1.3.6.1.4.1.9.9.371.1.1.5.14
This table contains configurations of Inter-VSAN Routing (IVR) Service Group. An Inter VSAN Routing Service Group defines a logical boundary for Inter-VSAN Routing. Inter-VSAN Routing is restricted among VSANs within their own Inter-VSAN Routing Service Group only.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrTopologyIvrSrvGrpEntry

civrTopologyIvrSrvGrpEntry 1.3.6.1.4.1.9.9.371.1.1.5.14.1
An entry (conceptual row) in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrTopologyIvrSrvGrpEntry  

civrTopologyIvrSrvGrpName 1.3.6.1.4.1.9.9.371.1.1.5.14.1.1
This object contains the name of the IVR Service Group corresponding to this conceptual row.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..80)  

civrTopologyIvrSrvGrpVsan2k 1.3.6.1.4.1.9.9.371.1.1.5.14.1.2
The list of VSANs that are part of this IVR Service Group specified by civrTopologyIvrSrvGrpName. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this IVR Service Group if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list.
Status: current Access: read-create
OBJECT-TYPE    
  FcList  

civrTopologyIvrSrvGrpVsan4k 1.3.6.1.4.1.9.9.371.1.1.5.14.1.3
The list of VSANs that are part of this IVR Service Group specified by civrTopologyIvrSrvGrpName. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2048 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this IVR Service Group if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list.
Status: current Access: read-create
OBJECT-TYPE    
  FcList  

civrTopologyIvrSrvGrpRowStatus 1.3.6.1.4.1.9.9.371.1.1.5.14.1.4
Status of this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

civrTopologyClearAfidConfig 1.3.6.1.4.1.9.9.371.1.1.5.15
This object clears the AFID configuration table, civrTopologyAfidConfTable, if this object is set to 'clear'. No action is taken if this object is set to 'noOp'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clear(1), noOp(2)  

civrAddIvrVirtualDomainsVsans2k 1.3.6.1.4.1.9.9.371.1.1.6.1
This object lists VSANs in which the virtual domains in a VSAN are added to the domain list (dmDatabaseTable in CISCO-DM-MIB) in that VSAN. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the add virtual domain VSAN list on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and civrAddIvrVirtualDomainsVsans4k are zero-length string, then the Virtual Domains are not added to any VSANs.
Status: current Access: read-write
OBJECT-TYPE    
  FcList  

civrAddIvrVirtualDomainsVsans4k 1.3.6.1.4.1.9.9.371.1.1.6.2
This object lists VSANs in which the virtual domains in a VSAN are added to the domain list (dmDatabaseTable in CISCO-DM-MIB) in that VSAN. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2048 through 2055, the second octet specifying VSANs 2056 through 2063, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the add virtual domain VSAN list on device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list. If the values of both this object and civrAddIvrVirtualDomainsVsans2k are zero-length string, then the Virtual Domains are not added to any VSANs.
Status: current Access: read-write
OBJECT-TYPE    
  FcList  

civrEnabledDeviceTable 1.3.6.1.4.1.9.9.371.1.2.2
This table contains the all IVR enabled devices known to the local device on each of the local VSANs. Note that the devices are learned using an internal protocol. So if a device in this table is not reachable, anymore from the local switch, then it is removed from this table. Also, if a new device is learned, it is added to this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CivrEnabledDeviceEntry

civrEnabledDeviceEntry 1.3.6.1.4.1.9.9.371.1.2.2.1
An entry (conceptual row) in this table. Each entry represents a device in a particular VSAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  CivrEnabledDeviceEntry  

civrEnabledDeviceVsan 1.3.6.1.4.1.9.9.371.1.2.2.1.1
The VSAN corresponding to this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  VsanIndex  

civrEnabledDeviceAutoFabricId 1.3.6.1.4.1.9.9.371.1.2.2.1.2
The Autonomous Fabric id corresponding to this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  CIvrAutonomousFabricId  

civrEnabledDeviceDomainId 1.3.6.1.4.1.9.9.371.1.2.2.1.3
The domain ID of this device corresponding this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  DomainId  

civrEnabledDeviceSwitchWwn 1.3.6.1.4.1.9.9.371.1.2.2.1.4
The switch WWN of this device.
Status: current Access: read-only
OBJECT-TYPE    
  FcNameId  

civrEnabledDeviceCapability 1.3.6.1.4.1.9.9.371.1.2.2.1.5
The switch WWN of this device.
Status: current Access: read-only
OBJECT-TYPE    
  BITS version1(0)  

civrZoneMemberFabricId 1.3.6.1.4.1.9.9.371.1.2.3
The fabric address of the IV zone member which is not able to participate in inter-VSAN communication because of conflicting domainIDs.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  FcAddressId  

civDomainIdConflictVsan 1.3.6.1.4.1.9.9.371.1.2.4
The VSAN in which the domainID conflict occurred.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  VsanIndex  

civrZoneSetActDeactPartialSucss 1.3.6.1.4.1.9.9.371.1.2.5
This object indicates if the IV zoneset activation/deactivation was partially success.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TruthValue  

civrAfidMisConfigVsan 1.3.6.1.4.1.9.9.371.1.2.6
The VSAN in which the AFID mis-configuration occurred.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  VsanIndex  

civrAfidMisConfigLocalAfid 1.3.6.1.4.1.9.9.371.1.2.7
The local AFID value in which the AFID mis-configuration occurred.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIvrAutonomousFabricId  

civrAfidMisConfigRemoteAfid 1.3.6.1.4.1.9.9.371.1.2.8
The remote AFID value in which the AFID mis-configuration occurred.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CIvrAutonomousFabricId  

civrAfidMisConfigLocalSWwn 1.3.6.1.4.1.9.9.371.1.2.9
The local switch WWN in which the AFID mis-configuration occurred.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  FcNameId  

civrAfidMisConfigRemoteSWwn 1.3.6.1.4.1.9.9.371.1.2.10
The remote switch WWN in which the AFID mis-configuration occurred.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  FcNameId  

civrTopologyMisConfigReason 1.3.6.1.4.1.9.9.371.1.2.11
The reason for a topology mis-configuration.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER unknown(1), afidMismatch(2)  

civrZoneActivationDoneNotify 1.3.6.1.4.1.9.9.371.0.1
This notification is generated on completion of an IV zoneset activation. civrZoneSetActDeactPartialSucss is valid only if the activation was successful.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

civrZoneDeactivationDoneNotify 1.3.6.1.4.1.9.9.371.0.2
This notification is generated on completion of an IV zoneset deactivation. civrZoneSetActDeactPartialSucss is valid only if the deactivation was successful.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

civrDomainConflictNotify 1.3.6.1.4.1.9.9.371.0.3
This notification is sent when domainID conflict occurs in a VSAN. The domainIDs in all the VSANs (dmDatabaseTable in CISCO-DM-MIB) which are configured to be carrying inter-VSAN trafic (civrTopologyConfigTable) must be unique. If not, there could be domainID conflicts.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

civrAfidConfigNotify 1.3.6.1.4.1.9.9.371.0.4
This notification is sent when an IVR AFID mis-configuration occurs.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

civrZoneServerMIBCompliances 1.3.6.1.4.1.9.9.371.2.1
OBJECT IDENTIFIER    

civrZoneServerMIBGroups 1.3.6.1.4.1.9.9.371.2.2
OBJECT IDENTIFIER    

civrZoneServerMIBCompliance 1.3.6.1.4.1.9.9.371.2.1.1
The compliance statement for entities which implement the Zone Server.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

civrZoneServerMIBComplianceRev1 1.3.6.1.4.1.9.9.371.2.1.2
The compliance statement for entities which implement the Zone Server.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

civrZoneServerMIBComplianceRev2 1.3.6.1.4.1.9.9.371.2.1.3
The compliance statement for entities which implement the Zone Server.
Status: current Access: read-only
MODULE-COMPLIANCE    

civrZoneConfigurationGroup 1.3.6.1.4.1.9.9.371.2.2.1
A collection of objects for displaying and configuring IvrZone Membership.
Status: current Access: read-only
OBJECT-GROUP    

civrTopologyGroup 1.3.6.1.4.1.9.9.371.2.2.2
A collection of objects for IVR topology.
Status: current Access: read-only
OBJECT-GROUP    

civrStatsGroup 1.3.6.1.4.1.9.9.371.2.2.3
A collection of objects for IVR status/statistics.
Status: current Access: read-only
OBJECT-GROUP    

civrNotificationGroup 1.3.6.1.4.1.9.9.371.2.2.4
A collection of notification(s) for monitoring IVR related events.
Status: current Access: read-only
NOTIFICATION-GROUP    

civrVirtualDomainsGroup 1.3.6.1.4.1.9.9.371.2.2.5
A collection of objects for IVR status/statistics.
Status: current Access: read-only
OBJECT-GROUP    

civrGenericGroup 1.3.6.1.4.1.9.9.371.2.2.6
A collection of objects for IVR generic configurations.
Status: current Access: read-only
OBJECT-GROUP    

civrTopologyGroupRev2 1.3.6.1.4.1.9.9.371.2.2.7
A collection of objects for IVR topology.
Status: current Access: read-only
OBJECT-GROUP    

civrZoneConfigurationGroupRev2 1.3.6.1.4.1.9.9.371.2.2.8
A collection of objects to support SCSI read only, Qos and Lun zoning in IVR Zone Membership configurations.
Status: current Access: read-only
OBJECT-GROUP    

civrNotificationGroupRev2 1.3.6.1.4.1.9.9.371.2.2.9
A collection of notification(s) for monitoring IVR related events.
Status: current Access: read-only
NOTIFICATION-GROUP