CISCO-LWAPP-EXT-MIB

File: CISCO-LWAPP-EXT-MIB.mib (53878 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
CISCO-SMI INET-ADDRESS-MIB SNMP-FRAMEWORK-MIB
IF-MIB CISCO-LWAPP-AP-MIB CISCO-LWAPP-WLAN-MIB
CISCO-LWAPP-DOT11-MIB CISCO-LWAPP-DOT11-CLIENT-MIB CISCO-LWAPP-RF-MIB
AIRESPACE-WIRELESS-MIB IANAifType-MIB CISCO-LWAPP-SYS-MIB
CISCO-LWAPP-TC-MIB

Imported symbols

MacAddress Counter64 TimeTicks
Gauge32 Integer32 MODULE-IDENTITY
OBJECT-TYPE Unsigned32 Counter32
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
DisplayString TruthValue RowStatus
ciscoMgmt InetAddressType InetAddress
SnmpAdminString ifIndex cLApSysMacAddress
cLApDot11IfSlotId cLApIfSmtDot11Bssid cLApLastRebootReason
cLApDataEncryptionStatus cLApName cLApEthernetIfSlotId
cLApDot11RadioCurrentChannel cLApRSSI cLApDot11RadioMACAddress
cLApDot11RadioChannelNumber cLWlanIndex cLWlanSsid
cldHtDot11nBand cldcClientMacAddress cldcApMacAddress
cldcClientSSID cLRFProfileName bsnDot11EssSecurityAuthType
IANAifType clsPortDot1dBasePort CLDot11Channel

Defined Types

CLSwitch  
This textual convention contains the state of a switch.
TEXTUAL-CONVENTION    
  INTEGER off(0), on(1)  

CLExtApDisassocReason  
This textual convention defines the possible reasons for an AP's disassociate to a controller. The semantics are as follows: unknown - The reason for the AP disassociated to controller is unknown. missedEchoFromAp - The reason is controller does not receive the echo packets from AP. wtpRest - The reason for AP not being able to associate is wtp rest. msgTimerExpiry - the reason is the message timer expiry. heartBeatExpiry - the reason is the heart beat expiry.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), missedEchoFromAp(2), wtpReset(3), msgTimerExpiry(4), heartBeatExpiry(5)  

ClExtPortModeConfigEntry  
SEQUENCE    
  clExtPortOperStatus INTEGER

ClExtIfEntry  
SEQUENCE    
  clExtIfSpeed Gauge32
  clExtIfSinceLastChange TimeTicks

ClExtApEntry  
SEQUENCE    
  clExtApRealTimeStatsModeEnabled CLSwitch
  clExtApMonitorMode INTEGER
  clExtApSysManufacture SnmpAdminString
  clExtApSysSoftwareName SnmpAdminString
  clExtApSysSoftwareVersion SnmpAdminString
  clExtApSysSoftwareVendor SnmpAdminString
  clExtApQosMinBandwidth Integer32
  clExtApTotalPhyInterfaceCount Unsigned32
  clExtApName SnmpAdminString

ClExtApDot11IfEntry  
SEQUENCE    
  clExtAp11nChannelBandwidth INTEGER
  clExtApDot11IfIANAType IANAifType
  clExtApIfPhyChannelAssignment CLSwitch
  clExtApDot11RadioStatsRxByteCount Counter64
  clExtApDot11RadioStatsTxByteCount Counter64
  clExtApDot11WirelessModeSupported INTEGER
  clExtApDot11IfAdminStatus INTEGER
  clExtApDot11IfOperStatus INTEGER
  cLExtAPDot11IfRTSThreshold Integer32

ClExtApDot11RadioStatsEntry  
SEQUENCE    
  clExtApDot11RadioStatsRetryFrameCount Counter64
  clExtApDot11RadioStatsRetryPacketCount Counter64
  clExtApDot11RadioStatsRxErrorPacketCount Counter32

ClExtApEthernetIfEntry  
SEQUENCE    
  clExtApEthernetIfOperStatus INTEGER
  clExtApEthernetIfRxBcastPkts Counter32
  clExtApEthernetIfRxMcastPkts Counter32
  clExtApEthernetIfTxBcastPkts Counter32
  clExtApEthernetIfTxMcastPkts Counter32

CLApOperationInfoEntry  
SEQUENCE    
  cLApOperationSysMacAddress MacAddress
  cLApOperationStatus INTEGER

ClExtWlanConfigEntry  
SEQUENCE    
  clExtWlanAdminStatus TruthValue
  clExtWlanBroadcastSsidEnable TruthValue
  clExtWlanLoadBalancingMode INTEGER
  clExtWlanSecurityAuthType INTEGER
  clExtWlanP2PBlocking TruthValue
  clExtWlanDot11Auth INTEGER
  clExtWlanSecurity INTEGER
  clExtWlanAuthenMode INTEGER
  clExtWlanSecurityCiphers INTEGER
  clExtWepCipherKeyIndex INTEGER
  clExtWepCipherKeyValue OCTET STRING
  clExtWepCipherKeyCharType INTEGER

ClExtClientEntry  
SEQUENCE    
  clExtClientProtocol INTEGER
  clExtClientPowerSaveMode INTEGER
  clExtClientUpTime TimeTicks
  clExtClientAuthFailReason DisplayString
  clExtClientRxThroughput Unsigned32
  clExtClientTxThroughput Unsigned32

ClExtHtMacOperationsEntry  
SEQUENCE    
  clExtHtDot11nAmpduEnable CLSwitch
  clExtHtDot11nGuardIntervalEnable CLSwitch

ClExtRFProfileEntry  
SEQUENCE    
  clExtRFProfileWirelessMode Unsigned32

ClExtAbnormalOfflineClientOnSecurityTypeEntry  
SEQUENCE    
  clExtSecurityType INTEGER
  clExtAbnormalOfflineClientCount Counter32

Defined Values

ciscoLwappExtMIB 1.3.6.1.4.1.9.9.9998
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information about the Web Ext Server on the controller. Particularly this mib covers the portal server for the wireless controllers. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications.
MODULE-IDENTITY    

ciscoLwappExtMIBNotifs 1.3.6.1.4.1.9.9.9998.0
OBJECT IDENTIFIER    

ciscoLwappExtMIBObjects 1.3.6.1.4.1.9.9.9998.1
OBJECT IDENTIFIER    

ciscoLwappExtMIBConform 1.3.6.1.4.1.9.9.9998.2
OBJECT IDENTIFIER    

ciscoLwappExtMIBNotifObjects 1.3.6.1.4.1.9.9.9998.3
OBJECT IDENTIFIER    

ciscoLwappExtConfig 1.3.6.1.4.1.9.9.9998.1.1
OBJECT IDENTIFIER    

ciscoLwappExtStats 1.3.6.1.4.1.9.9.9998.1.2
OBJECT IDENTIFIER    

clExtSys 1.3.6.1.4.1.9.9.9998.1.1.1
OBJECT IDENTIFIER    

clExtNMHeartBeatEnable 1.3.6.1.4.1.9.9.9998.1.1.1.1
This object specifies whether heart beat trap to network manager is enabled or disabled. If the value is on the Network Manager Heart Beat feature is Enabled otherwise Disabled.
Status: current Access: read-write
OBJECT-TYPE    
  CLSwitch  

clExtAgentResetSystem 1.3.6.1.4.1.9.9.9998.1.1.1.2
reset the switch
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

clExtAgentClearConfig 1.3.6.1.4.1.9.9.9998.1.1.1.3
Clear configuration to factory defaults
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(2)  

clExtSystemCurrentTime 1.3.6.1.4.1.9.9.9998.1.1.1.4
Use this attribute to change the System time on the Switch. Specify the new time in this Format yyyy-mm-dd hh24:mi:ss. For example, 2013-05-01 18:00:00.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

clExtPortModeConfigTable 1.3.6.1.4.1.9.9.9998.1.1.1.5
This table contains the entries for physical port related status
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtPortModeConfigEntry

clExtPortModeConfigEntry 1.3.6.1.4.1.9.9.9998.1.1.1.5.1
This entry contains the Switch's physical port phyical mode related attribues
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtPortModeConfigEntry  

clExtPortOperStatus 1.3.6.1.4.1.9.9.9998.1.1.1.5.1.1
The switch's Port Operation Status.This is the current actual status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3), admindown(4)  

clExtSysMaxNewConnectionPerSecond 1.3.6.1.4.1.9.9.9998.1.1.1.6
This object specifies maximum number of new client count connect to the controller per-second, it's a performance data and associated with the platform
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

clExtIf 1.3.6.1.4.1.9.9.9998.1.1.2
OBJECT IDENTIFIER    

clExtIfTable 1.3.6.1.4.1.9.9.9998.1.1.2.1
A list of interface entries. The number of entries is given by the value of ifNumber.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtIfEntry

clExtIfEntry 1.3.6.1.4.1.9.9.9998.1.1.2.1.1
An entry containing management information applicable to a particular interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtIfEntry  

clExtIfSpeed 1.3.6.1.4.1.9.9.9998.1.1.2.1.1.1
An estimate of the interface's current bandwidth in million bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295 bps) and ifHighSpeed must be used to report the interface's speed. For a sub-layer which has no concept of bandwidth, this object should be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

clExtIfSinceLastChange 1.3.6.1.4.1.9.9.9998.1.1.2.1.1.2
The value of time duration since the time the interface entered its current operational state. If the current time is prior to the last updating of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

clExtAp 1.3.6.1.4.1.9.9.9998.1.1.3
OBJECT IDENTIFIER    

clExtApTable 1.3.6.1.4.1.9.9.9998.1.1.3.1
This table represents the information about the 802.11 LWAPP Access Points that have joined the controller. LWAPP APs exchange configuration messages with the controller and get the required configuration for their 802.11 related operations, after they join the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtApEntry

clExtApEntry 1.3.6.1.4.1.9.9.9998.1.1.3.1.1
Each entry in this table provides information about one 802.11 LWAPP Access Point that has joined the controller. Entries are removed when the APs lose their association with the controller due to loss of communication.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtApEntry  

clExtApRealTimeStatsModeEnabled 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.1
This object specifies whether currently stats mode is 'realtime'. There are two stats-mode, realtime and normal, that specifies the stats-timer range to be 10-180 sec and 2-5 sec each. Set to on if current mode is realtime.
Status: current Access: read-write
OBJECT-TYPE    
  CLSwitch  

clExtApMonitorMode 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.2
This object specifies the monitor mode of AP. monitor : no client can connect. normal : no monitor function at all. semimonitor : AP can monitor it's working radio while clients connected. The mapping between clExtApMonitorMode and CISCO existing function is as the belows: clExtApMonitorMode Cisco Exist Value LOCAL AP MODE: LOCAL + ROGUE DETECTION : disable MONITOR AP MODE: MONITOR SEMIMONITOR AP MODE: LOCAL + ROGUE DETECTION : enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(0), monitor(1), semimonitor(2)  

clExtApSysManufacture 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.3
This object specifies the AP manufacture.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

clExtApSysSoftwareName 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.4
This object specifies the AP software name.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

clExtApSysSoftwareVersion 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.5
This object specifies the AP software version.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

clExtApSysSoftwareVendor 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.6
This object specifies the AP software vendor.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

clExtApQosMinBandwidth 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.7
This object specifies the minimum bandwidth for QOS on the AP. It is measured by Mbps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

clExtApTotalPhyInterfaceCount 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.8
This object specifies the total wired physical interface count for the Access Points that have joined the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clExtApName 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.9
This object represents the administrative name assigned to the AP by the user. If an AP is not configured, its factory default name will be ap: eg. ap:af:12:be.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

clExtApDot11IfTable 1.3.6.1.4.1.9.9.9998.1.1.3.2
This table represents the information about the basic functional parameters corresponding to the dot11 interfaces of the APs that have joined the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtApDot11IfEntry

clExtApDot11IfEntry 1.3.6.1.4.1.9.9.9998.1.1.3.2.1
An entry in this table represents the 802.11 functional parameters of the dot11 interface of an AP that has joined the controller. Entries are added when the APs associate to this controller and deleted when they lose their association.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtApDot11IfEntry  

clExtAp11nChannelBandwidth 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.1
This object indicates the channel bandwidth for this AP. This applies to 802.11n networks only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forty(1), twenty(2)  

clExtApDot11IfIANAType 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.2
This object represents the type of this interface. The value of the type is defined by IANA.
Status: current Access: read-only
OBJECT-TYPE    
  IANAifType  

clExtApIfPhyChannelAssignment 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.3
If this value is on, then bsnAPDot11CurrentChannel in bsnAPIfDot11PhyDSSSTable is assigned by dynamic algorithm and is read-only.
Status: current Access: read-write
OBJECT-TYPE    
  CLSwitch  

clExtApDot11RadioStatsRxByteCount 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.4
This object represents the total bytes of packets received on the radio.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

clExtApDot11RadioStatsTxByteCount 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.5
This object represents the total bytes of packets transmitted on the radio.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

clExtApDot11WirelessModeSupported 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.6
This object represents wireless mode supported. bit 0 - dot11a bit 1 - dot11b bit 2 - dot11g bit 3 - dot11an bit 4 - dot11gn AP can support wireless multi-mode, the value can follow the example: gn an g b a -------------------- 0 0 1 1 0 value:6, means b/g
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..31  

clExtApDot11IfAdminStatus 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.7
This object represents the AP's interface administrational status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

clExtApDot11IfOperStatus 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.8
This object represents the AP's wireless interface current operational status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3), admindown(4)  

cLExtAPDot11IfRTSThreshold 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.9
This object represents RTS threshold value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

clExtApDot11RadioStatsTable 1.3.6.1.4.1.9.9.9998.1.1.3.3
This table represents the statistics information about the radios of the APs that have joined the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtApDot11RadioStatsEntry

clExtApDot11RadioStatsEntry 1.3.6.1.4.1.9.9.9998.1.1.3.3.1
An entry in this table represents a statistics of the radio of an AP that has joined the conttroller. Entries are added when the APs associate to this controller and deleted when they lose their association.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtApDot11RadioStatsEntry  

clExtApDot11RadioStatsRetryFrameCount 1.3.6.1.4.1.9.9.9998.1.1.3.3.1.1
This object represents the total number of downstream retry frames on the radio.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

clExtApDot11RadioStatsRetryPacketCount 1.3.6.1.4.1.9.9.9998.1.1.3.3.1.2
This object represents the total number of downstream retry packets on the radio.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

clExtApDot11RadioStatsRxErrorPacketCount 1.3.6.1.4.1.9.9.9998.1.1.3.3.1.3
This object represents the total number of received error packets on the radio .
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

clExtApEthernetIfTable 1.3.6.1.4.1.9.9.9998.1.1.3.4
This table represents the information about the basic functional parameters corresponding to the Ethernet interfaces of the APs that have joined the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtApEthernetIfEntry

clExtApEthernetIfEntry 1.3.6.1.4.1.9.9.9998.1.1.3.4.1
An entry in this table represents the functional parameters of the Ethernet interface of an AP that has joined the controller. Entries are added when the APs associate to this controller and deleted when they lose their association.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtApEthernetIfEntry  

clExtApEthernetIfOperStatus 1.3.6.1.4.1.9.9.9998.1.1.3.4.1.1
This object represents the operational state of the physical Ethernet interface on the AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3), admindown(4)  

clExtApEthernetIfRxBcastPkts 1.3.6.1.4.1.9.9.9998.1.1.3.4.1.2
This object represents total number of broadcast packets received on the interface
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

clExtApEthernetIfRxMcastPkts 1.3.6.1.4.1.9.9.9998.1.1.3.4.1.3
This object represents total number of multicast packets received on the interface
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

clExtApEthernetIfTxBcastPkts 1.3.6.1.4.1.9.9.9998.1.1.3.4.1.4
This object represents total number of broadcast packets transmitted on the interface
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

clExtApEthernetIfTxMcastPkts 1.3.6.1.4.1.9.9.9998.1.1.3.4.1.5
This object represents total number of multicast packets transmitted on the interface
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLApOperationInfoTable 1.3.6.1.4.1.9.9.9998.1.1.3.5
This table represents the operation information for each AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLApOperationInfoEntry

cLApOperationInfoEntry 1.3.6.1.4.1.9.9.9998.1.1.3.5.1
Each entry in this table provides operation information for each AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLApOperationInfoEntry  

cLApOperationSysMacAddress 1.3.6.1.4.1.9.9.9998.1.1.3.5.1.1
This object specifies the AP mac address.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

cLApOperationStatus 1.3.6.1.4.1.9.9.9998.1.1.3.5.1.2
This object represents operation status of each ap.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disassociated(0), associated(1)  

clExtWlan 1.3.6.1.4.1.9.9.9998.1.1.4
OBJECT IDENTIFIER    

clExtWlanConfigTable 1.3.6.1.4.1.9.9.9998.1.1.4.1
This table represents the WLAN configuration sent by the controller to the LWAPP APs for their operation. LWAPP APs exchange configuration messages with the controller and get the required configuration for their 802.11 related operations. As part of these messages, the WLAN configuration is pushed by the controller to the LWAPP APs. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLWlanRowStatus object.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtWlanConfigEntry

clExtWlanConfigEntry 1.3.6.1.4.1.9.9.9998.1.1.4.1.1
Each entry in this table represents the WLAN configuration sent by the controller to LWAPP APs for use during their operations. entries can be added/deleted by explicit management actions by NMS or by user console
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtWlanConfigEntry  

clExtWlanAdminStatus 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.1
Administrative Status of ESS(WLAN). By disabling an ESS the corresponding SSID is no longer broadcasted in AP beacons.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

clExtWlanBroadcastSsidEnable 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.2
This attribute when enabled allows the switch to broadcast this SSID and when disabled doesn't allow that.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

clExtWlanLoadBalancingMode 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.3
This object indicates the load balancing mode enabled on the controller for this WLAN . A value of 'none' indicates Load Balance is turned off for this Wlan. A value of 'clientCount' indicates load balance is based on AP client count scheme. And a value of 'uplinkUsage' indicates load balance is based on AP uplink usage scheme.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), uplinkUsage(1), clientCount(2)  

clExtWlanP2PBlocking 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.4
This object represents per WLAN peer-to-peer blocking behavior on controller. Peer-to-peer blocking means traffic between two clients on same VLAN will not be bridged. false : Peer-to-peer blocking is disabled and traffic is bridged locally within the controller. true : The packet will be discarded or be forwarded on the upstream VLAN. If it is forwarded on the upstream VLAN, the device 'north' of the controller can then make the decision about decision about what to do with the packet.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

clExtWlanSecurityAuthType 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.5
This object represents per WLAN type of 802.11 Authentication. authOpen : The WLAN uses open authentication method authSharedKey : The WLAN uses shared authentication method authCiscoLeap : The WLAN uses CISCO LEAP authentication method
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER authOpen(0), authSharedKey(1), authCiscoLeap(128)  

clExtWlanDot11Auth 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.6
This object allows the user to configure 802.11 Authentication.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER opensystem(0), sharekey(1)  

clExtWlanSecurity 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.7
This object allows the user to configure the security type in frame.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), wpa(1), wpa2(2), wapi(3)  

clExtWlanAuthenMode 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.8
This object allows the user to configure the authentication mode.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), psk(1), radius(2), wapi-cer(3)  

clExtWlanSecurityCiphers 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.9
This object allows the user to configure encryption mode.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), wep40(1), wep104(2), tkip(3), aesccmp(4), wpi-sms4(5)  

clExtWepCipherKeyIndex 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.10
This object represents the key index of WEP. According to 802.11 standard 4 keys are supported. So 802.11 Mobile Stations(Client) can have upto 4 keys. This index is for informing Mobile Station which key it should use for Static WEP Authentication.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

clExtWepCipherKeyValue 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.11
This object represents the key value of WEP. For wep104 encryption either 26 bit hex key or 13 bit ascii key should be specified. For wep40 encryption 10 bit hex key or 5 bit ascii key should be specified.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(5..26)  

clExtWepCipherKeyCharType 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.12
This object represents the key type of WEP. Length of key specified in Key depends on this attribute.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(1), hex(2), ascii(3)  

clExtDot11Client 1.3.6.1.4.1.9.9.9998.1.1.5
OBJECT IDENTIFIER    

clExtClientTable 1.3.6.1.4.1.9.9.9998.1.1.5.1
This table represents the 802.11 wireless clients that are associated with the APs that have joined this controller. An entry is created automatically by the controller when the client gets associated to the AP. An existing entry gets deleted when the association gets dropped. Each client added to this table is uniquely identified by the client's MAC address.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtClientEntry

clExtClientEntry 1.3.6.1.4.1.9.9.9998.1.1.5.1.1
Each entry represents a conceptual row in this table and provides the information about the clients associated to the APs that have joined the controller. An entry is identified the client's MAC address.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtClientEntry  

clExtClientProtocol 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.1
The 802.11 protocol type of the client. 'dot11a' - The client is using 802.11a standard to connect to the access point (AP) 'dot11b' - The client is using 802.11b standard to connect to the access point (AP) 'dot11g' - The client is using 802.11g standard to connect to the access point (AP) 'dot11n5' - The client is using 802.11n standard with 5 GHz frequency to connect to the access point (AP). 'dot11n24' - The client is using 802.11n standard with 2.4 GHz frequency to connect to the access point (AP)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot11a(1), dot11b(2), dot11g(4), dot11n5(8), dot11n24(16)  

clExtClientPowerSaveMode 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.2
This object indicates the power management mode of the client. The possible two modes are: active(0) - this client is not in power-save mode and it is actively sending or receiving data. powersave(1) - this client is in power-save mode and it wakes up once a while to check for pending data.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(0), powersave(1)  

clExtClientUpTime 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.3
This object indicates the duration for which the client has been associated with this device.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

clExtClientAuthFailReason 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.5
This object specifies the reason of the client authentication failure.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

clExtClientRxThroughput 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.6
This object indicates the receiving throughput which expressing a instantaneous throughput of the bytes received by the client over last time slot.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clExtClientTxThroughput 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.7
This object indicates the transmitting throughput which expressing a instantaneous throughput of the bytes transmitted by the client over last time slot.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

clExtDot11 1.3.6.1.4.1.9.9.9998.1.1.6
OBJECT IDENTIFIER    

clExtHtMacOperationsTable 1.3.6.1.4.1.9.9.9998.1.1.6.1
This table represents the operational parameters at the MAC layer for the 802.11n networks managed through the controller. An agent adds an entry to this table for every 802.11n band on startup.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtHtMacOperationsEntry

clExtHtMacOperationsEntry 1.3.6.1.4.1.9.9.9998.1.1.6.1.1
Each entry represents the operational parameters at the MAC layer for 802.11n networks.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtHtMacOperationsEntry  

clExtHtDot11nAmpduEnable 1.3.6.1.4.1.9.9.9998.1.1.6.1.1.1
This object is used to indicate the support for 802.11n A-MPDU on this band. A value of 'on' indicates that A-MPDU is enabled for this band. A value of 'off' indicates that A-MPDU is disabled for this band.
Status: current Access: read-write
OBJECT-TYPE    
  CLSwitch  

clExtHtDot11nGuardIntervalEnable 1.3.6.1.4.1.9.9.9998.1.1.6.1.1.2
This object is used to indicate the support for 802.11n guard interval on this band. A value of 'on' indicates that guard interval is enabled for this band. A value of 'off' indicates that guard interval is disabled for this band.
Status: current Access: read-write
OBJECT-TYPE    
  CLSwitch  

clExtRF 1.3.6.1.4.1.9.9.9998.1.1.7
OBJECT IDENTIFIER    

clExtRFProfileTable 1.3.6.1.4.1.9.9.9998.1.1.7.1
This table lists the configuration for each RF profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtRFProfileEntry

clExtRFProfileEntry 1.3.6.1.4.1.9.9.9998.1.1.7.1.1
An entry containing the configuration attributes that affect the operation of 802.11 RF domain. Entries can be added/deleted by explicit management action from NMS/EMS or through user console.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtRFProfileEntry  

clExtRFProfileWirelessMode 1.3.6.1.4.1.9.9.9998.1.1.7.1.1.1
This object represents wireless mode configuration. bit 0 - dot11a bit 1 - dot11b bit 2 - dot11g bit 3 - dot11an bit 4 - dot11gn AP can support wireless multi-mode, the value can follow the example: gn an g b a -------------------- 0 0 1 1 0 value:6, means b/g
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..31  

clExtSecurity 1.3.6.1.4.1.9.9.9998.1.1.8
OBJECT IDENTIFIER    

clExtAbnormalOfflineClientOnSecurityTypeTable 1.3.6.1.4.1.9.9.9998.1.1.8.1
This table lists the abnormal offline clients for the required security type.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClExtAbnormalOfflineClientOnSecurityTypeEntry

clExtAbnormalOfflineClientOnSecurityTypeEntry 1.3.6.1.4.1.9.9.9998.1.1.8.1.1
Each entry in this table represents the abnormal offline counter based on security type.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClExtAbnormalOfflineClientOnSecurityTypeEntry  

clExtSecurityType 1.3.6.1.4.1.9.9.9998.1.1.8.1.1.1
This object represents the client security type. open : The client uses open authentication method wepPsk : The client uses WEP/PSK authentication method peapSim : The client uses PEAP/SIM authentication method webAuth : The client uses WebAuth authentication method
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER open(1), wepPsk(2), peapSim(3), webAuth(4)  

clExtAbnormalOfflineClientCount 1.3.6.1.4.1.9.9.9998.1.1.8.1.1.2
This object represents the current abnormal offline clients based on security type on the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLExtApDisassocReason 1.3.6.1.4.1.9.9.9998.3.1
This object specifies the failure reasons when the AP disassociate with a controller.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CLExtApDisassocReason  

cLExtDot11ClientAssocFailReason 1.3.6.1.4.1.9.9.9998.3.2
This object specifies the reason of the station association failure.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

cLExtApDetectedMacAddress 1.3.6.1.4.1.9.9.9998.3.3
This object represents the radio MAC address common to the dot11 interfaces of the detected AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

cLExtApDetectedChannel 1.3.6.1.4.1.9.9.9998.3.4
This object represents the detected channel number.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CLDot11Channel  

cLExtApDectedSsid 1.3.6.1.4.1.9.9.9998.3.5
This object represents the SSID used by the rogue AP to intrude the network.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString  

ciscoLwappApAssociatedNotify 1.3.6.1.4.1.9.9.9998.0.1
This notification is generated whenever an AP joins the controller successfully. This notification contains information about the last reboot reason, Data Encryption status and the MAC address of the AP.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappApDisassociated 1.3.6.1.4.1.9.9.9998.0.2
This notification is generated whenever an AP disassociate the controller successfully. This notification contains information about the last associate fail reason and MAC address of the AP.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappExtDot11ClientAuthenticationFailTrap 1.3.6.1.4.1.9.9.9998.0.3
This notification is generated whenever client Authentication failure is detected.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappExtDot11ClientAssocFailTrap 1.3.6.1.4.1.9.9.9998.0.4
This notification is generated whenever station associtation failure is detacted.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappExtAdjChannelOverRssiDetected 1.3.6.1.4.1.9.9.9998.0.5
This notification is generated whenever an AP is detected at the Adjacent channels
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappExtAdjChannelOverRssiRemoved 1.3.6.1.4.1.9.9.9998.0.6
This notification is generated whenever an AP is detected at the Adjacent channels and then subsequently if its been removed from the network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappExtCurrentChannelOverRssiDetected 1.3.6.1.4.1.9.9.9998.0.7
This notification is generated whenever an AP is detected at the Current channels
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappExtCurrentChannelOverRssiRemoved 1.3.6.1.4.1.9.9.9998.0.8
This notification is generated whenever an AP is detected at the Current channels and then subsequently if its been removed from the network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappExtClientOverRssiDetected 1.3.6.1.4.1.9.9.9998.0.9
This notification is generated when a client's rssi exceeds threshold configured add to network. The details of AP and Clients is sent in the notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappExtClientOverRssiRemoved 1.3.6.1.4.1.9.9.9998.0.10
This notification is generated when a client's rssi exceeds threshold configured removed from network. The details of AP and Clients is sent in the notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE