CISCO-MGX82XX-CARD-FEATURE-MIB

File: CISCO-MGX82XX-CARD-FEATURE-MIB.mib (8163 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF BASIS-MIB
CISCOWAN-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
MODULE-COMPLIANCE OBJECT-GROUP cardSpecific
ciscoWan

Defined Values

ciscoMgx82xxCardFeatureMIB 1.3.6.1.4.1.351.150.74
The MIB module which describes the features supported in MGX82XX products. This MIB Module provides the features supported in Controller Cards in MGX8250 and MGX8220. Terminologies used: PXM : Processor Switch Module. This is controller card in MGX8250. ASC : AXIS Shelf Controller. This is controller card in MGX8220. VSI : Virtual Switch Interface, a hardware-independent switch control protocol. This allows a Switch to be controlled by a multiple controllers such as PNNI, MPLS. These control planes can be internal or external to the switch.The VSI interface defines the messages and associated functions which allow communication between the controller and the switch.This interface is expected to support all types of connections (voice,data,frame relay,ATM) for PVCs, SPVCs and SVCs. Controller - Software ( and possibly hardware) which manages topology and network resources and performs VSI Master function. This performs source routing for end-to-end SVCs, including general call acceptance GCAC,setup calls with other controllers. PNNI and MPLS are examples of controllers.
MODULE-IDENTITY    

ascFeatures 1.3.6.1.4.1.351.110.3.5
OBJECT IDENTIFIER    

pxmFeatures 1.3.6.1.4.1.351.110.3.15
OBJECT IDENTIFIER    

coreCardCommands 1.3.6.1.4.1.351.110.3.20
OBJECT IDENTIFIER    

vsiControllersAllowed 1.3.6.1.4.1.351.110.3.15.1
This respesents bit map of the VSI Controllers supported. The bit positions are : BIT 0 - PAR(Portable AutoRoute Controller) BIT 1 - PNNI(Private network to network Interface) BIT 2 - TAG(Tag Switching or MPLS Controller) (e.g. A value of 1 in BIT 0 indicates the presence of PAR ) Remaining bits are set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16777215  

apsCardAttributes 1.3.6.1.4.1.351.110.3.15.2
This respesents bit map of the APS card attributes supported. The bit position supported are: BITs 0, 1 - unused BIT 2 - APS standard protocol configured (1 = TRUE ; 0 = FALSE) BIT 3, 4 ,5 - unused BIT 6 - Card HW supports APS 1+1 on two cards (1 = TRUE ; 0 = FALSE) BIT 7 - Card FW supports APS (1 = TRUE ; 0 = FALSE) Remaining bits are set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

trkCACEnable 1.3.6.1.4.1.351.110.3.15.3
This MIB variable allows to add a new connection on the feeder trunk even if it is over-subscribed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

pxmCardCacMode 1.3.6.1.4.1.351.110.3.15.4
This object identifies the CAC mode set on a card. If this is set to pcrBasedCAC(1) then the CAC calculations will be done based on PCR on the connection. If this set to scrBasedCAC(2) then the CAC calculations are done based on the scr of the connections. This will be applicable only if CAC is enabled (i.e trkCACEnable is set to enable(2)).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pcrBasedCac(1), scrBasedCac(2)  

redundancyAllowed 1.3.6.1.4.1.351.110.3.5.1
This object identifies whether redundancy is allowed in MGX82XX shelf.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER redNotAllowed(1), redAllowed(2)  

switchCoreCard 1.3.6.1.4.1.351.110.3.20.1
This object is used for performing switchover of core card set. The core card set includes Controller Card and Service Redundancy Module(SRM). The possible values are : noAction (1): No operation doswitchcc (2): Perform switchover operation instswitchcc (3): Perform switchover operation fallbackswitchcc(4):
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), doswitchcc(2), instswitchcc(3), fallbackswitchcc(4)  

cmCardFeatureMIBConformance 1.3.6.1.4.1.351.150.74.2
OBJECT IDENTIFIER    

cmCardFeatureMIBGroups 1.3.6.1.4.1.351.150.74.2.1
OBJECT IDENTIFIER    

cmCardFeatureMIBCompliances 1.3.6.1.4.1.351.150.74.2.2
OBJECT IDENTIFIER    

cmCardFeatureCompliance 1.3.6.1.4.1.351.150.74.2.2.1
The compliance statement for objects related to Frame Relay Ports.
Status: current Access: read-write
MODULE-COMPLIANCE    

cmPxmCardFeatureGroup 1.3.6.1.4.1.351.150.74.2.1.1
The collection of objects which are used to represent Processor Module(PXM) Features.
Status: current Access: read-write
OBJECT-GROUP    

cmAscCardFeatureGroup 1.3.6.1.4.1.351.150.74.2.1.2
The collection of objects which are used to represent Axis Shelf Controller(ASC) Features.
Status: current Access: read-write
OBJECT-GROUP    

cmCoreCardFeatureGroup 1.3.6.1.4.1.351.150.74.2.1.3
The collection of objects which are used to represent core card related objects.
Status: current Access: read-write
OBJECT-GROUP