CISCO-NETSYNC-MIB

File: CISCO-NETSYNC-MIB.mib (68256 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Gauge32 Unsigned32 MODULE-COMPLIANCE
NOTIFICATION-GROUP OBJECT-GROUP TruthValue
TEXTUAL-CONVENTION TimeStamp SnmpAdminString
ciscoMgmt

Defined Types

CiscoNetsyncIfType  
Network synchronization clock source Interface type. Netsync interface Interface type ======================== ============== netsyncIfTypeUnknown Unknown netsyncIfTypeInternal Internal netsyncIfTypeEthernet Ethernet netsyncIfTypeSonet SONET netsyncIfTypeTop Timing Over Packet netsyncIfTypeExt External interface netsyncIfTypeController T1/E1 Controller netsyncIfTypeGps GPS netsyncIfTypeAtm ATM For external and GPS interface types, the following syntax is used for specifying an interface: // where slot : slot number of the device where card is present. card : bay number in which card is inserted. port : port number on the card. signal type: hardware signal of the specified //. Examples of signal type are T1 SF and T1 ESF.
TEXTUAL-CONVENTION    
  INTEGER netsyncIfTypeUnknown(1), netsyncIfTypeInternal(2), netsyncIfTypeEthernet(3), netsyncIfTypeSonet(4), netsyncIfTypeTop(5), netsyncIfTypeExt(6), netsyncIfTypeController(7), netsyncIfTypeGps(8), netsyncIfTypeAtm(9)  

CiscoNetsyncNetworkOption  
Network synchronization networking options. Network option Network option type =========================== =================== netsyncNetworkOptionUnknown Unknown network option netsyncNetworkOption1 Option I netsyncNetworkOption2Gen1 Option II Generation 1 netsyncNetworkOption2Gen2 Option II Generation 2 netsyncNetworkOption3 Option III netsyncNetworkOptionInvalid Invalid network option Option I refers to ITU-T Option I synchronization networks. Option II refers to ITU-T Option II synchronization networks designed for North America. Option III refers to ITU-T Option III synchronization networks designed for Japan.
TEXTUAL-CONVENTION    
  INTEGER netsyncNetworkOptionUnknown(1), netsyncNetworkOption1(2), netsyncNetworkOption2Gen1(3), netsyncNetworkOption2Gen2(4), netsyncNetworkOption3(5), netsyncNetworkOptionInvalid(6)  

CiscoNetsyncEECOption  
Network synchronization EEC (Ethernet Equipment Clock) options. The EEC options are for Synchronous Ethernet devices and define the requirements for clocks, e.g. bandwidth, frequency accuracy, holdover and noise generation. Two options are defined: EEC-Option 1: Designed to interwork with network optimized for the 2048 kbit/s hierarchy. EEC-Option 2: Designed to interwork with network optimized for the 1544 kbit/s hierarchy. netsyncEECOptionUnknown Unknown netsyncEECOption1 EEC option 1 netsyncEECOption2 EEC option 2 netsyncEECOptionInvalid Invalid EEC option
TEXTUAL-CONVENTION    
  INTEGER netsyncEECOptionUnknown(1), netsyncEECOption1(2), netsyncEECOption2(3), netsyncEECOptionInvalid(4)  

CiscoNetsyncQLMode  
The clock mode of the network synchronization clock selection process as described in ITU-T standard G.781 section 5.12. G.781 clock selection runs in one of two clock modes: QL (Quality Level) enabled mode and QL disabled mode. netsyncQLModeUnknown - QL mode unknown netsyncQLModeQlDisabled - QL-disabled mode; clock selection is running in QL disabled mode, which primarily considers the source's priority as the clock selection criteria. netsyncQLModeQlEnabled - QL-enabled mode clock selection is running in QL enabled mode, which primarily considers the source's clock quality level and priority as the clock selection criteria.
TEXTUAL-CONVENTION    
  INTEGER netsyncQLModeUnknown(1), netsyncQLModeQlDisabled(2), netsyncQLModeQlEnabled(3)  

CiscoNetsyncClockMode  
Clock operating mode: netsyncClockModeUnknown - system is unable to determine the operating mode. netsyncClockModeFreerun - free-running mode. netsyncClockModeHoldover - holdover mode. netsyncClockModeLocked - a valid clock source is locked.
TEXTUAL-CONVENTION    
  INTEGER netsyncClockModeUnknown(1), netsyncClockModeFreerun(2), netsyncClockModeHoldover(3), netsyncClockModeLocked(4)  

CiscoNetsyncQualityLevel  
Clock source QL (quality level) is defined in ITU-T G.781 section 5.4 to reflect the synchronization quality within a network Option, i.e. I, II, and III. The following clock source quality levels are defined for the synchronization process of Option I: QL-PRC Primary reference clock QL-SSU-A Type I or V slave clock defined in ITU-T G.811 QL-SSU-B Type VI slave clock defined in ITU-T G.812 QL-SEC Synchronous equipment clock QL-DNU Do not use for synchronization QL-INVx Unallocated SSM value, where x represent the value of SSM received QL-FAILED Signal failure state QL-UNC Unconnected to an input QL-NSUPP Not supporting the SSM processing The following clock source quality levels are defined for the synchronization process of Option II: QL-PRS PRS traceable QL-STU Synchronized; traceability unknown QL-ST2 Stratum 2 QL-TNC Transit node clock QL-ST3E Stratum 3E QL-ST3 Stratum 3 QL-SMC SONET clock self timed QL-ST4 Stratum 4 freerun QL-PROV Provisionable by the network operator QL-DUS Do not use for synchronization QL-INVx Unallocated SSM value, where x represent the value of SSM received QL-FAILED Signal failure state QL-UNC Unconnected to an input QL-NSUPP Not supporting the SSM processing The following clock source quality levels are defined for the synchronization process of Option III: QL-UNK Unknown clock source QL-SEC Synchronous equipment clock QL-INVx Unallocated SSM value, where x represent the value of SSM received QL-FAILED Signal failure state QL-UNC Unconnected to an input QL-NSUPP Not supporting the SSM processing
TEXTUAL-CONVENTION    
  INTEGER netsyncQualityLevelNULL(1), netsyncQualityLevelDNU(2), netsyncQualityLevelDUS(3), netsyncQualityLevelFAILED(4), netsyncQualityLevelINV0(5), netsyncQualityLevelINV1(6), netsyncQualityLevelINV2(7), netsyncQualityLevelINV3(8), netsyncQualityLevelINV4(9), netsyncQualityLevelINV5(10), netsyncQualityLevelINV6(11), netsyncQualityLevelINV7(12), netsyncQualityLevelINV8(13), netsyncQualityLevelINV9(14), netsyncQualityLevelINV10(15), netsyncQualityLevelINV11(16), netsyncQualityLevelINV12(17), netsyncQualityLevelINV13(18), netsyncQualityLevelINV14(19), netsyncQualityLevelINV15(20), netsyncQualityLevelNSUPP(21), netsyncQualityLevelPRC(22), netsyncQualityLevelPROV(23), netsyncQualityLevelPRS(24), netsyncQualityLevelSEC(25), netsyncQualityLevelSMC(26), netsyncQualityLevelSSUA(27), netsyncQualityLevelSSUB(28), netsyncQualityLevelST2(29), netsyncQualityLevelST3(30), netsyncQualityLevelST3E(31), netsyncQualityLevelST4(32), netsyncQualityLevelSTU(33), netsyncQualityLevelTNC(34), netsyncQualityLevelUNC(35), netsyncQualityLevelUNK(36)  

CiscoNetsyncSSMCap  
Network synchronization clock source interface SSM (Synchronization Status Message) capability. SSM Capability Capability information ===================== ====================== netsyncSSMCapNone No SSM capability netsyncSSMCapTxRx To transmit and receive SSM netsyncSSMCapTx To transmit SSM only netsyncSSMCapRx To receive SSM only netsyncSSMCapInvalid Capability invalid or unsupported
TEXTUAL-CONVENTION    
  INTEGER netsyncSSMCapNone(1), netsyncSSMCapTxRx(2), netsyncSSMCapTx(3), netsyncSSMCapRx(4), netsyncSSMCapInvalid(5)  

CiscoNetsyncESMCCap  
Network synchronization clock source interface ESMC (Ethernet Synchronization Messaging Channel) capability. ESMC Capability Capability information ====================== ====================== netsyncESMCCapNone No ESMC capability netsyncESMCCapTxRx To transmit and receive ESMC netsyncESMCCapTx To transmit SSM only netsyncESMCCapRx To receive SSM only netsyncESMCCapInvalid Capability invalid or unsupported
TEXTUAL-CONVENTION    
  INTEGER netsyncESMCCapNone(1), netsyncESMCCapTxRx(2), netsyncESMCCapTx(3), netsyncESMCCapRx(4), netsyncESMCCapInvalid(5)  

CiscoNetsyncAlarmInfo  
Input clock source's alarm reasons: netsyncSrcAlarmReasonAIS - Alarm Indication Signal netsyncSrcAlarmReasonOOR - Out of range netsyncSrcAlarmReasonOIR - Online Insertion Removal netsyncSrcAlarmReasonInternal - Internal
TEXTUAL-CONVENTION    
  BITS netsyncSrcAlarmReasonAIS(0), netsyncSrcAlarmReasonOOR(1), netsyncSrcAlarmReasonOIR(2), netsyncSrcAlarmReasonInternal(3)  

CnsClkSelGlobalEntry  
SEQUENCE    
  cnsClkSelGloProcIndex Unsigned32
  cnsClkSelGlobProcessMode CiscoNetsyncQLMode
  cnsClkSelGlobClockMode CiscoNetsyncClockMode
  cnsClkSelGlobNetsyncEnable TruthValue
  cnsClkSelGlobRevertiveMode TruthValue
  cnsClkSelGlobESMCMode TruthValue
  cnsClkSelGlobEECOption CiscoNetsyncEECOption
  cnsClkSelGlobNetworkOption CiscoNetsyncNetworkOption
  cnsClkSelGlobHoldoffTime Unsigned32
  cnsClkSelGlobWtrTime Unsigned32
  cnsClkSelGlobNofSources Unsigned32
  cnsClkSelGlobLastHoldoverSeconds Gauge32
  cnsClkSelGlobCurrHoldoverSeconds Gauge32

CnsSelectedInputSourceEntry  
SEQUENCE    
  cnsSelInpSrcNetsyncIndex Unsigned32
  cnsSelInpSrcName SnmpAdminString
  cnsSelInpSrcIntfType CiscoNetsyncIfType
  cnsSelInpSrcQualityLevel CiscoNetsyncQualityLevel
  cnsSelInpSrcPriority Unsigned32
  cnsSelInpSrcTimestamp TimeStamp
  cnsSelInpSrcFSW TruthValue
  cnsSelInpSrcMSW TruthValue

CnsInputSourceEntry  
SEQUENCE    
  cnsInpSrcNetsyncIndex Unsigned32
  cnsInpSrcName SnmpAdminString
  cnsInpSrcIntfType CiscoNetsyncIfType
  cnsInpSrcPriority Unsigned32
  cnsInpSrcESMCCap CiscoNetsyncESMCCap
  cnsInpSrcSSMCap CiscoNetsyncSSMCap
  cnsInpSrcQualityLevelTxCfg CiscoNetsyncQualityLevel
  cnsInpSrcQualityLevelRxCfg CiscoNetsyncQualityLevel
  cnsInpSrcQualityLevelTx CiscoNetsyncQualityLevel
  cnsInpSrcQualityLevelRx CiscoNetsyncQualityLevel
  cnsInpSrcQualityLevel CiscoNetsyncQualityLevel
  cnsInpSrcHoldoffTime Unsigned32
  cnsInpSrcWtrTime Unsigned32
  cnsInpSrcLockout TruthValue
  cnsInpSrcSignalFailure TruthValue
  cnsInpSrcAlarm TruthValue
  cnsInpSrcAlarmInfo CiscoNetsyncAlarmInfo
  cnsInpSrcFSW TruthValue
  cnsInpSrcMSW TruthValue

CnsExtOutputEntry  
SEQUENCE    
  cnsExtOutListIndex Unsigned32
  cnsExtOutSelNetsyncIndex Unsigned32
  cnsExtOutName SnmpAdminString
  cnsExtOutIntfType CiscoNetsyncIfType
  cnsExtOutQualityLevel CiscoNetsyncQualityLevel
  cnsExtOutPriority Unsigned32
  cnsExtOutFSW TruthValue
  cnsExtOutMSW TruthValue
  cnsExtOutSquelch TruthValue

CnsT4ClockSourceEntry  
SEQUENCE    
  cnsT4ClkSrcNetsyncIndex Unsigned32
  cnsT4ClkSrcName SnmpAdminString
  cnsT4ClkSrcIntfType CiscoNetsyncIfType
  cnsT4ClkSrcPriority Unsigned32
  cnsT4ClkSrcESMCCap CiscoNetsyncESMCCap
  cnsT4ClkSrcSSMCap CiscoNetsyncSSMCap
  cnsT4ClkSrcQualityLevelTxCfg CiscoNetsyncQualityLevel
  cnsT4ClkSrcQualityLevelRxCfg CiscoNetsyncQualityLevel
  cnsT4ClkSrcQualityLevelTx CiscoNetsyncQualityLevel
  cnsT4ClkSrcQualityLevelRx CiscoNetsyncQualityLevel
  cnsT4ClkSrcQualityLevel CiscoNetsyncQualityLevel
  cnsT4ClkSrcHoldoffTime Unsigned32
  cnsT4ClkSrcWtrTime Unsigned32
  cnsT4ClkSrcLockout TruthValue
  cnsT4ClkSrcSignalFailure TruthValue
  cnsT4ClkSrcAlarm TruthValue
  cnsT4ClkSrcAlarmInfo CiscoNetsyncAlarmInfo
  cnsT4ClkSrcFSW TruthValue
  cnsT4ClkSrcMSW TruthValue

Defined Values

ciscoNetsyncMIB 1.3.6.1.4.1.9.9.761
The Synchronous Ethernet (SyncE) MIB is defined for monitoring network synchronization based on ITU-T G.781 clock selection. Synchronous Ethernet (SyncE) is a standard defined for delivering timing to the remote NEs through a Packet Network. SyncE is well defined by ITU-T which included G.8261, G.8262, G.8264 and G.781. It leverages the PHY layer of Ethernet to transmit frequency to the remote sites. Its functionality and accuracy mimics that of the SONET/SDH network because of its physical layer characteristic. In order to allow best clock source traceabiliy, correctly define the timing source and helps preventing timing loop, Synchronization Status Message is required for SyncE. This is similar to SONET/SDH. However, since SONET/SDH use 4 bits from the two S bytes in the SONET/SDH overhead frame for such message, Ethernet relies on a different channel called ESMC (Ethernet Synchronization Messaging Channel) which is based on IEEE 802.3 Organization Specific Slow Protocol. Glossary: AIS: Alarm Indication Signal ATM: Asynchronous Transfer Mode EEC: Ethernet Equipment Clock ESMC: Ethernet Synchronization Messaging Channel QL: Quality Level SASE: Stand Alone Synchronization Equipment SSM: Synchronization Status Messaging
MODULE-IDENTITY    

ciscoNetsyncMIBNotifs 1.3.6.1.4.1.9.9.761.0
OBJECT IDENTIFIER    

ciscoNetsyncMIBObjects 1.3.6.1.4.1.9.9.761.1
OBJECT IDENTIFIER    

ciscoNetsyncMIBConform 1.3.6.1.4.1.9.9.761.2
OBJECT IDENTIFIER    

ciscoNetsyncMIBTables 1.3.6.1.4.1.9.9.761.1.1
OBJECT IDENTIFIER    

cnsClkSelGlobalTable 1.3.6.1.4.1.9.9.761.1.1.1
G.781 clock selection process table. This table contains the global parameters for the G.781 clock selection process.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CnsClkSelGlobalEntry

cnsClkSelGlobalEntry 1.3.6.1.4.1.9.9.761.1.1.1.1
An entry is added to cnsClkSelGlobalTable when G.781 clock selection is enabled in the device configuration. The entry is removed when G.781 clock selection is removed from the configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  CnsClkSelGlobalEntry  

cnsClkSelGloProcIndex 1.3.6.1.4.1.9.9.761.1.1.1.1.1
An index that uniquely represents a clock selection process. This index is assigned arbitrarily by the system and may not be persistent across reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cnsClkSelGlobProcessMode 1.3.6.1.4.1.9.9.761.1.1.1.1.2
This object indicates the QL mode of the network synchronization clock selection process as described in ITU-T standard G.781 section 5.12.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQLMode  

cnsClkSelGlobClockMode 1.3.6.1.4.1.9.9.761.1.1.1.1.3
This object indicates the operating mode of the system clock.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncClockMode  

cnsClkSelGlobNetsyncEnable 1.3.6.1.4.1.9.9.761.1.1.1.1.4
This object indicates whether the G.781 clock selection is enabled or not. 'true' - G.781 clock selection is enabled 'false' - G.781 clock selection is disabled
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsClkSelGlobRevertiveMode 1.3.6.1.4.1.9.9.761.1.1.1.1.5
This object indicates the revertive mode setting in the G.781 clock selection process. The switching of clock sources can be made revertive or non-revertive. In non-revertive mode, an alternate clock source is maintained even after the original clock source has recovered from the failure that caused the switch. In revertive mode, the clock selection process switches back to the original clock source after recovering from the failure.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsClkSelGlobESMCMode 1.3.6.1.4.1.9.9.761.1.1.1.1.6
This object indicates if global ESMC is enabled. With ESMC enabled globally, the system is capable of handling ESMC messages.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsClkSelGlobEECOption 1.3.6.1.4.1.9.9.761.1.1.1.1.7
This object indicates the network synchronization EEC (Ethernet Equipment Clock) option.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncEECOption  

cnsClkSelGlobNetworkOption 1.3.6.1.4.1.9.9.761.1.1.1.1.8
This object indicates the synchronization network option.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncNetworkOption  

cnsClkSelGlobHoldoffTime 1.3.6.1.4.1.9.9.761.1.1.1.1.9
This object indicates the global holdoff time in the G.781 clock selection process.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cnsClkSelGlobWtrTime 1.3.6.1.4.1.9.9.761.1.1.1.1.10
This object indicates the global wait-to-restore time in the G.781 clock selection process.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cnsClkSelGlobNofSources 1.3.6.1.4.1.9.9.761.1.1.1.1.11
This object indicates the number of synchronization sources currently configured for the G.781 clock selection process.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..255  

cnsClkSelGlobLastHoldoverSeconds 1.3.6.1.4.1.9.9.761.1.1.1.1.12
This object indicates the duration of the last holdover period in seconds. If the holdover duration is less than a second, the object will carry the value zero.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cnsClkSelGlobCurrHoldoverSeconds 1.3.6.1.4.1.9.9.761.1.1.1.1.13
This object indicates the duration of the current holdover period. If a system clock is in holdover mode, the object carries the current holdover duration in seconds. If the system clock is not in holdover, the object carries the value 0.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cnsSelectedInputSourceTable 1.3.6.1.4.1.9.9.761.1.1.2
T0 selected clock source table. This table contains the selected clock source for the input T0 clock.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CnsSelectedInputSourceEntry

cnsSelectedInputSourceEntry 1.3.6.1.4.1.9.9.761.1.1.2.1
An entry is created in the table when the G.781 clock selection process has successfully selected a T0 clock source. The entry shall remain during the time the G.781 clock selection process remains enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  CnsSelectedInputSourceEntry  

cnsSelInpSrcNetsyncIndex 1.3.6.1.4.1.9.9.761.1.1.2.1.1
An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cnsSelInpSrcName 1.3.6.1.4.1.9.9.761.1.1.2.1.2
This object indicates the name of the selected T0 clock.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(1..255)  

cnsSelInpSrcIntfType 1.3.6.1.4.1.9.9.761.1.1.2.1.3
This object indicates the type of the selected T0 clock.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncIfType  

cnsSelInpSrcQualityLevel 1.3.6.1.4.1.9.9.761.1.1.2.1.4
This object indicates the selected T0 clock source's effective quality level, which is the derived clock quality based on the three factors: (a) Received quality level. (b) Configured Rx quality level. This factor supersedes (a). (c) System overridden quality level as a result of exceptional events such as signal failure or ESMC failure. This factor supersedes (a) and (b).
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsSelInpSrcPriority 1.3.6.1.4.1.9.9.761.1.1.2.1.5
This object indicates the configured priority of the selected T0 clock. A smaller value represents a higher priority.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..1024  

cnsSelInpSrcTimestamp 1.3.6.1.4.1.9.9.761.1.1.2.1.6
This object indicates the timestamp of the T0 clock source being selected by the G.781 clock selection process.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cnsSelInpSrcFSW 1.3.6.1.4.1.9.9.761.1.1.2.1.7
This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source. The 'true' value indicates the currently selected clock source is a result of the forced switching. The 'false' value indicates the currently selected clock source is not a result of forced switching.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsSelInpSrcMSW 1.3.6.1.4.1.9.9.761.1.1.2.1.8
This object indicates the manual switching flag. The 'true' value indicates the currently selected clock source is a result of the manual switch command. The command allows a user to select a synchronization source assuming it is enabled, not locked out, not in signal fail condition, and has a QL better than DNU in QL-enabled mode. Furthermore, in QL-enabled mode, a manual switch can be performed only to a source which has the highest available QL.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsInputSourceTable 1.3.6.1.4.1.9.9.761.1.1.3
T0 clock source table. This table contains a list of input sources for input T0 clock selection.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CnsInputSourceEntry

cnsInputSourceEntry 1.3.6.1.4.1.9.9.761.1.1.3.1
An entry is created in the table when a user adds a T0 clock source in the configuration. An entry is removed in the table when a user removes a T0 clock source from the configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  CnsInputSourceEntry  

cnsInpSrcNetsyncIndex 1.3.6.1.4.1.9.9.761.1.1.3.1.1
An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cnsInpSrcName 1.3.6.1.4.1.9.9.761.1.1.3.1.2
This object indicates the name of an input clock source configured for the T0 clock selection.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(1..255)  

cnsInpSrcIntfType 1.3.6.1.4.1.9.9.761.1.1.3.1.3
This object indicates the type of an input clock source configured for the T0 clock selection.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncIfType  

cnsInpSrcPriority 1.3.6.1.4.1.9.9.761.1.1.3.1.4
This object indicates the priority of an input clock source configured for the T0 clock selection. A smaller value represents a higher priority.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..1024  

cnsInpSrcESMCCap 1.3.6.1.4.1.9.9.761.1.1.3.1.5
This object indicates the ESMC capability of an input clock source configured for the T0 clock selection. This is applicable only to Synchronous Ethernet input clock source identified by cnsInpSrcIntfType 'netsyncIfTypeEthernet'.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncESMCCap  

cnsInpSrcSSMCap 1.3.6.1.4.1.9.9.761.1.1.3.1.6
This object indicates the SSM capability of an input clock source configured for the T0 clock selection. This is applicable only to any synchronous interface clock source except SyncE interface, which is identified by cnsInpSrcIntfType 'netsyncIfTypeEthernet'.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncSSMCap  

cnsInpSrcQualityLevelTxCfg 1.3.6.1.4.1.9.9.761.1.1.3.1.7
This object indicates the configured transmit clock quality level of an input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsInpSrcQualityLevelRxCfg 1.3.6.1.4.1.9.9.761.1.1.3.1.8
This object indicates the configured receive clock quality level of an input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsInpSrcQualityLevelTx 1.3.6.1.4.1.9.9.761.1.1.3.1.9
This object indicates the most recent clock quality level transmitted on the input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsInpSrcQualityLevelRx 1.3.6.1.4.1.9.9.761.1.1.3.1.10
This object indicates the last clock quality level received on the input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsInpSrcQualityLevel 1.3.6.1.4.1.9.9.761.1.1.3.1.11
This object indicates the current clock quality level of the input clock source. This is the effective quality which is derived from three values: 1) most recent clock quality level received, 2) forced clock quality level (entered via configuration) 3) overridden clock quality level as a result of line protocol down, signal failure, or alarms.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsInpSrcHoldoffTime 1.3.6.1.4.1.9.9.761.1.1.3.1.12
This object indicates the hold-off time value of an input clock source. The hold-off time prevents short activation of signal failure is passed to the selection process. When a signal failure event is reported on a clock source, it waits the duration of the hold-off time before declaring signal failure on the clock source.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cnsInpSrcWtrTime 1.3.6.1.4.1.9.9.761.1.1.3.1.13
This object indicates the wait-to-restore time value of an input clock source. The wait-to-restore time ensures that a previous failed synchronization source is only again considered as available by the selection process if it is fault-free for a certain time. When a signal failure condition is cleared on a clock source, it waits the duration of the wait-to-restore time before clearing the signal failure status on the clock source.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cnsInpSrcLockout 1.3.6.1.4.1.9.9.761.1.1.3.1.14
This object indicates whether or not the lockout command has been applied to a clock source. The 'true' value means the clock source is not considered by the selection process.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsInpSrcSignalFailure 1.3.6.1.4.1.9.9.761.1.1.3.1.15
This object indicates whether or not a signal failure event is currently being reported on the input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsInpSrcAlarm 1.3.6.1.4.1.9.9.761.1.1.3.1.16
This object indicates whether or not an alarm event is currently being reported on the input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsInpSrcAlarmInfo 1.3.6.1.4.1.9.9.761.1.1.3.1.17
This object indicates the alarm reasons of an input clock source if an alarm event is being reported on it.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncAlarmInfo  

cnsInpSrcFSW 1.3.6.1.4.1.9.9.761.1.1.3.1.18
This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source. The 'true' value indicates the currently selected clock source is a result of the forced switching. The 'false' value indicates the currently selected clock source is not a result of forced switching.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsInpSrcMSW 1.3.6.1.4.1.9.9.761.1.1.3.1.19
This object indicates the manual switching flag. The 'true' value indicates the currently selected clock source is a result of the manual switching. The switch allows a user to select a synchronization source assuming it is enabled, not locked out, not in signal fail condition, and has a QL better than DNU in QL-enabled mode. A clock source is enabled when it occupies a row in cnsInputSourceTable. A clock source is not locked out when cnsInpSrcLockout contains the value 'false'. A clock source is not in signal failure condition when cnsInpSrcSignalFailure contains the value 'false'. The QL is identified in cnsInpSrcQualityLevel. In QL-enabled mode, a manual switch can be performed only to a source which has the highest available QL.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsExtOutputTable 1.3.6.1.4.1.9.9.761.1.1.4
T4 external output table. This table contains a list of T4 external outputs. Each T4 external output is associated with clock source(s) to be found in cnsT4ClockSourceTable. The clock selection process considers all the available clock sources and select the T4 clock source based on the G.781 clock selection algorithm.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CnsExtOutputEntry

cnsExtOutputEntry 1.3.6.1.4.1.9.9.761.1.1.4.1
An entry is created in the table when a user adds a T4 external output in the configuration. A T4 external output configured input clock sources are defined in cnsT4ClockSourceTable. An entry is removed from the table when a user removes a T4 external output from the configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  CnsExtOutputEntry  

cnsExtOutListIndex 1.3.6.1.4.1.9.9.761.1.1.4.1.1
An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cnsExtOutSelNetsyncIndex 1.3.6.1.4.1.9.9.761.1.1.4.1.2
An index that uniquely represents the selected input clock source whose information is reported by a row in cnsT4ClockSourceTable. The index lists the value of cnsT4ClkSrcNetsyncIndex, which is the input clock source of the T4 external output selected by the G.781 clock selection process.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cnsExtOutName 1.3.6.1.4.1.9.9.761.1.1.4.1.3
This object indicates the name of a T4 external output.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(1..255)  

cnsExtOutIntfType 1.3.6.1.4.1.9.9.761.1.1.4.1.4
This object indicates the interface type of the T4 external output.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncIfType  

cnsExtOutQualityLevel 1.3.6.1.4.1.9.9.761.1.1.4.1.5
This object indicates the clock quality of the T4 external output.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsExtOutPriority 1.3.6.1.4.1.9.9.761.1.1.4.1.6
This object indicates the priority of the selected clock source for a T4 external output. A smaller value represents a higher priority.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..1024  

cnsExtOutFSW 1.3.6.1.4.1.9.9.761.1.1.4.1.7
This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source, The T4 selected synchronization source is identified by cnsExtOutSelNetsyncIndex, which contains the index to the clock source in cnsT4ClockSourceTable. The 'true' value indicates the currently selected T4 clock source is a result of the forced switching. The 'false' value indicates the currently selected T4 clock source is not a result of forced switching.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsExtOutMSW 1.3.6.1.4.1.9.9.761.1.1.4.1.8
This object indicates the manual switching flag. The 'true' value indicates the currently selected T4 clock source is a result of the manual switch command. The command allows a user to select a synchronization source assuming it is enabled, not locked out, not in signal fail condition, and has a QL better than DNU in QL-enabled mode. A clock source is enabled when it occupies in row in cnsT4ClockSourceTable. A clock source is not locked out when cnsT4ClkSrcLockout contains the value 'false'. A clock source is not in signal failure condition when cnsT4ClkSrcSignalFailure contains the value 'false'. The QL is identified in cnsT4ClkSrcQualityLevel. In QL-enabled mode, a manual switch can be performed only to a source which has the highest available QL.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsExtOutSquelch 1.3.6.1.4.1.9.9.761.1.1.4.1.9
This object indicates whether or not a T4 external output is squelched. Squelching is a sychronization function defined to prevent transmission of a timing signal with a quality that is lower than the quality of the clock in the receiving networks element or SASE. It is also used for the prevention of timing loops.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsT4ClockSourceTable 1.3.6.1.4.1.9.9.761.1.1.5
T4 clock source table. This table contains a list of input sources for a specific T4 external output. An entry shall be added to cnsExtOutputTable first. Then clock sources shall be added in this table for the selection process to select the appropriate T4 clock source.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CnsT4ClockSourceEntry

cnsT4ClockSourceEntry 1.3.6.1.4.1.9.9.761.1.1.5.1
An entry is created in the table when a user adds a clock source to a T4 external output in the configuration. The T4 external output is defined in the T4 external output table. An entry is removed in the table when a user removes a T4 clock source from the configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  CnsT4ClockSourceEntry  

cnsT4ClkSrcNetsyncIndex 1.3.6.1.4.1.9.9.761.1.1.5.1.1
An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across reboots.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cnsT4ClkSrcName 1.3.6.1.4.1.9.9.761.1.1.5.1.2
This object indicates the name of a input clock source configured for the T4 clock selection.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(1..255)  

cnsT4ClkSrcIntfType 1.3.6.1.4.1.9.9.761.1.1.5.1.3
This object indicates the type of an input clock source configured for the T4 clock selection.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncIfType  

cnsT4ClkSrcPriority 1.3.6.1.4.1.9.9.761.1.1.5.1.4
This object indicates the priority of an input clock source configured for the T4 clock selection. A smaller value represents a higher priority.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..1024  

cnsT4ClkSrcESMCCap 1.3.6.1.4.1.9.9.761.1.1.5.1.5
This object indicates the ESMC capability of an input clock source configured for the T4 clock selection. This is applicable only to Synchronous Ethernet input clock source identified by cnsT4ClkSrcIntfType 'netsyncIfTypeEthernet'.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncESMCCap  

cnsT4ClkSrcSSMCap 1.3.6.1.4.1.9.9.761.1.1.5.1.6
This object indicates the SSM capability of an input clock source configured for the T4 clock selection. This is applicable only to any synchronous interface clock source except SyncE interface, which is identified by cnsT4ClkSrcIntfType 'netsyncIfTypeEthernet'.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncSSMCap  

cnsT4ClkSrcQualityLevelTxCfg 1.3.6.1.4.1.9.9.761.1.1.5.1.7
This object indicates the configured transmit clock quality level of a T4 input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsT4ClkSrcQualityLevelRxCfg 1.3.6.1.4.1.9.9.761.1.1.5.1.8
This object indicates the configured receive clock quality level of a T4 input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsT4ClkSrcQualityLevelTx 1.3.6.1.4.1.9.9.761.1.1.5.1.9
This object indicates the most recent clock quality level transmitted on the T4 input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsT4ClkSrcQualityLevelRx 1.3.6.1.4.1.9.9.761.1.1.5.1.10
This object indicates the last clock quality level received on the T4 input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsT4ClkSrcQualityLevel 1.3.6.1.4.1.9.9.761.1.1.5.1.11
This object indicates the current clock quality level of the T4 input clock source. This is the effective quality which is derived from three values: 1) most recent clock quality level received, 2) forced clock quality level (entered via configuration) 3) overridden clock quality level as a result of line protocol down, signal failure, or alarms.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncQualityLevel  

cnsT4ClkSrcHoldoffTime 1.3.6.1.4.1.9.9.761.1.1.5.1.12
This object indicates the hold-off time value of a T4 input clock source. The hold-off time prevents short activation of signal failure is passed to the selection process. When a signal failure event is reported on a clock source, it waits the duration of the hold-off time before declaring signal failure on the clock source.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cnsT4ClkSrcWtrTime 1.3.6.1.4.1.9.9.761.1.1.5.1.13
This object indicates the wait-to-restore time value of a T4 input clock source. The wait-to-restore time ensures that a previous failed synchronization source is only again considered as available by the selection process if it is fault-free for a certain time. When a signal failure condition is cleared on a clock source, it waits the duration of the wait-to-restore time before clearing the signal failure status on the clock source.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cnsT4ClkSrcLockout 1.3.6.1.4.1.9.9.761.1.1.5.1.14
This object indicates whether or not the lockout command has been applied on a T4 clock source. The 'true' value means the clock source is not considered by the selection process.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsT4ClkSrcSignalFailure 1.3.6.1.4.1.9.9.761.1.1.5.1.15
This object indicates whether or not a signal failure event is currently being reported on the T4 input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsT4ClkSrcAlarm 1.3.6.1.4.1.9.9.761.1.1.5.1.16
This object indicates whether or not an alarm event is currently being reported on the T4 input clock source.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsT4ClkSrcAlarmInfo 1.3.6.1.4.1.9.9.761.1.1.5.1.17
This object indicates the alarm reasons of a T4 input clock source if an alarm event is being reported on the clock source.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoNetsyncAlarmInfo  

cnsT4ClkSrcFSW 1.3.6.1.4.1.9.9.761.1.1.5.1.18
This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source. The 'true' value indicates the currently selected T4 clock source is a result of the forced switching. The 'false' value indicates the currently selected T4 clock source is not a result of forced switching.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsT4ClkSrcMSW 1.3.6.1.4.1.9.9.761.1.1.5.1.19
This object indicates the manual switching flag. The 'true' value indicates the currently selected T4 clock source is a result of the manual switching. The switch allows a user to select a synchronization source assuming it is enabled, not locked out, not in signal fail condition, and has a QL better than DNU in QL-enabled mode. A clock source is enabled when it occupies a row in cnsT4ClockSourceTable. A clock source is not locked out when cnsT4ClkSrcLockout contains the value 'false'. A clock source is not in signal failure condition when cnsT4ClkSrcSignalFailure contains the value 'false'. The QL is identified in cnsT4ClkSrcQualityLevel. In QL-enabled mode, a manual switch can be performed only to a source which has the highest available QL.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cnsNotifObjects 1.3.6.1.4.1.9.9.761.1.2
OBJECT IDENTIFIER    

cnsInpSrcFailClear 1.3.6.1.4.1.9.9.761.1.2.1
This object indicates the clear status of a signal failure event. A value of 'true' means a signal failure event reported on a clock source has been cleared. A value of 'false' means a signal event has been reported on a clock source.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TruthValue  

cnsInpSrcAlarmClear 1.3.6.1.4.1.9.9.761.1.2.2
This object indicates the clear status of an alarm event. A value of 'true' means an alarm event reported on a clock source has been cleared. A value of 'false' means an alarm event has been reported on a clock source.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TruthValue  

ciscoNetsyncMIBNotifControl 1.3.6.1.4.1.9.9.761.1.3
OBJECT IDENTIFIER    

cnsMIBEnableStatusNotification 1.3.6.1.4.1.9.9.761.1.3.1
A control object to enable/disable ciscoNetsyncSelectedT0Clock, ciscoNetsyncSelectedT4Clock, ciscoNetsyncInputSignalFailureStatus, ciscoNetsyncInputAlarmStatus notifications at the system level. This object should hold any of the below values. true - The notif is enabled globally for the system false- The notif is disabled globally for the system
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ciscoNetsyncSelectedT0Clock 1.3.6.1.4.1.9.9.761.0.1
T0 clock selection notification. This notification is generated when one of the following conditions is met: - A new clock source is selected by the T0 clock selection. - The clock quality of a T0 selected clock source is changed. - The configured priority of a T0 selected clock source is changed.
Status: current Access: read-write
NOTIFICATION-TYPE    

ciscoNetsyncSelectedT4Clock 1.3.6.1.4.1.9.9.761.0.2
T4 clock selection notification. This notification is generated when one of the following conditions is met: - A new clock source is selected by the T4 clock selection. - The clock quality of a T4 selected clock source is changed. - The configured priority of a T4 selected clock source is changed.
Status: current Access: read-write
NOTIFICATION-TYPE    

ciscoNetsyncInputSignalFailureStatus 1.3.6.1.4.1.9.9.761.0.3
Input clock source signal failure notification. This notification is generated when a signal failure event is reported on an input clock source. One of the conditions a signal failure event could be due to interface shutdown.
Status: current Access: read-write
NOTIFICATION-TYPE    

ciscoNetsyncInputAlarmStatus 1.3.6.1.4.1.9.9.761.0.4
Input clock source alarm notification. This notification is generated when an alarm event is reported on an input clock source.
Status: current Access: read-write
NOTIFICATION-TYPE    

ciscoNetsyncMIBCompliances 1.3.6.1.4.1.9.9.761.2.1
OBJECT IDENTIFIER    

ciscoNetsyncMIBGroups 1.3.6.1.4.1.9.9.761.2.2
OBJECT IDENTIFIER    

ciscoNetsyncMIBCompliance 1.3.6.1.4.1.9.9.761.2.1.1
This is a default module-compliance containing default object groups.
Status: current Access: read-write
MODULE-COMPLIANCE    

cnsClkSelGlobalObjectGroup 1.3.6.1.4.1.9.9.761.2.2.1
This group contains all objects referenced by the G.781 clock selection process table.
Status: current Access: read-write
OBJECT-GROUP    

cnsSelectedInputSourceObjectGroup 1.3.6.1.4.1.9.9.761.2.2.2
This group contains all objects referenced by cnsSelectedInputSourceTable.
Status: current Access: read-write
OBJECT-GROUP    

cnsInputSourceObjectGroup 1.3.6.1.4.1.9.9.761.2.2.3
This group contains all objects referenced by cnsInputSourceTable.
Status: current Access: read-write
OBJECT-GROUP    

cnsExtOutputObjectGroup 1.3.6.1.4.1.9.9.761.2.2.4
This group contains all objects referenced by cnsExtOutputTable.
Status: current Access: read-write
OBJECT-GROUP    

cnsT4ClkSrcObjectGroup 1.3.6.1.4.1.9.9.761.2.2.5
This group contains all objects referenced by cnsT4ClockSourceTable.
Status: current Access: read-write
OBJECT-GROUP    

cnsMIBNotifEnablesGroup 1.3.6.1.4.1.9.9.761.2.2.6
The collection of objects which are used to enable notification.
Status: current Access: read-write
OBJECT-GROUP    

ciscoNetsyncMIBNotificationGroup 1.3.6.1.4.1.9.9.761.2.2.7
The is the netsync notification group.
Status: current Access: read-write
NOTIFICATION-GROUP