CISCO-RHINO-MIB

File: CISCO-RHINO-MIB.mib (67506 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
SNMPv2-CONF RFC1213-MIB CISCO-SMI
CISCO-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Counter32 Gauge32 Integer32
TEXTUAL-CONVENTION TimeStamp DisplayString
TruthValue InterfaceIndex MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP ifIndex
workgroup Unsigned32

Defined Types

PsType  
Power Supply type
TEXTUAL-CONVENTION    
  INTEGER powerone(0), astec(1), minus48VDC(2), empty(3), ac1100W(4), ac1200W(5), dc1200W(6), pem(7), ac1360W(8), dc1360W(9), ac2000W(10), dc2000W(11), acpem(12), ac175W(13)  

OperStatus  
Operational status of a chassis component. fanAlarm(4) is only applicable to the C5500 power supply. A fault(3) supercedes a fanAlarm(4). partialFault(5) & empty(6) are used by the Cisco6400 for the fan status to indicate partial fans failure & fan not present. A fault(3) value indicates total fans failure in the C6400.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), ok(2), fault(3), fanAlarm(4), partialFault(5), empty(6)  

AdminStatus  
Admin status of a chassis component.
TEXTUAL-CONVENTION    
  INTEGER enable(1), disable(2), reset(3)  

Led  
LED status
TEXTUAL-CONVENTION    
  INTEGER off(1), green(2), red(3), yellow(4), blinkgreen(5), blinkyellow(6), blinkred(7), unknown(8)  

PcmciaType  
PCMCIA card type
TEXTUAL-CONVENTION    
  INTEGER unknown(1), empty(2), flash(3), disk(4)  

CiscoLS1010ModuleEntry  
SEQUENCE    
  ciscoLS1010ModuleIndex INTEGER
  ciscoLS1010ModuleType INTEGER
  ciscoLS1010ModuleSerialNumber Integer32
  ciscoLS1010ModuleHwVersion Integer32
  ciscoLS1010ModuleSwVersion Integer32
  ciscoLS1010ModuleDescr DisplayString
  ciscoLS1010ModuleNumSubModules INTEGER
  ciscoLS1010ModuleAdminStatus AdminStatus
  ciscoLS1010ModuleOperStatus OperStatus
  ciscoLS1010ModuleHwVersionMinor Unsigned32
  ciscoLS1010ModuleSerialNumberString DisplayString

CiscoLS1010SubModuleEntry  
SEQUENCE    
  ciscoLS1010SubModuleIndex INTEGER
  ciscoLS1010SubModuleType INTEGER
  ciscoLS1010SubModuleSerialNumber Integer32
  ciscoLS1010SubModuleHwVersion Integer32
  ciscoLS1010SubModuleSwVersion Integer32
  ciscoLS1010SubModuleDescr DisplayString
  ciscoLS1010SubModuleNumPorts INTEGER
  ciscoLS1010SubModuleAdminStatus INTEGER
  ciscoLS1010SubModuleHwVersionMinor Integer32
  ciscoLS1010SubModuleOperStatus OperStatus
  ciscoLS1010SubModuleSerialNumberString DisplayString

CiscoLS1010PortEntry  
SEQUENCE    
  ciscoLS1010PortIndex INTEGER
  ciscoLS1010PortIfIndex InterfaceIndex

ClsEnetPortEntry  
SEQUENCE    
  clsEnetPortDuplex INTEGER
  clsEnetPortAdminSpeed INTEGER
  clsEnetPortType INTEGER
  clsEnetPortLinkStatus INTEGER

ClsPortLedEntry  
SEQUENCE    
  clsPortLedIndex INTEGER
  clsPortLedType INTEGER
  clsPortLedStatus INTEGER

CiscoAtmSwitchInvalidCellHeaderEntry  
SEQUENCE    
  ciscoAtmSwitchInvalidCellHeaderIndex INTEGER
  ciscoAtmSwitchInvalidCellHeader OCTET STRING

Defined Values

ciscoLS1010ChassisMIB 1.3.6.1.4.1.9.5.11
-Added enum sixPortDS3 for ciscoLS1010SubModuleType. -Added enum nodeSwitchProcessor2ndGeneration for ciscoLS1010ModuleType. -Added enum ac175W for psType. -Added Group object for Notification objects.
MODULE-IDENTITY    

ciscoLS1010ChassisMIBObjects 1.3.6.1.4.1.9.5.11.1
OBJECT IDENTIFIER    

ciscoLS1010ChassisGroup 1.3.6.1.4.1.9.5.11.1.1
OBJECT IDENTIFIER    

ciscoLS1010ModuleGroup 1.3.6.1.4.1.9.5.11.1.2
OBJECT IDENTIFIER    

ciscoLS1010SubModuleGroup 1.3.6.1.4.1.9.5.11.1.3
OBJECT IDENTIFIER    

ciscoLS1010PortGroup 1.3.6.1.4.1.9.5.11.1.4
OBJECT IDENTIFIER    

ciscoLS1010CpuSwitchGroup 1.3.6.1.4.1.9.5.11.1.5
OBJECT IDENTIFIER    

clsEnetPortGroup 1.3.6.1.4.1.9.5.11.1.6
OBJECT IDENTIFIER    

clsPortLedGroup 1.3.6.1.4.1.9.5.11.1.7
OBJECT IDENTIFIER    

ciscoLS1010ChassisSysType 1.3.6.1.4.1.9.5.11.1.1.1
The chassis system type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), ls1010(2), c8510(3), cisco6400(4), c8540(5), tgx8750(6), wsx6302(7), c2948g(8), c4908g(9)  

ciscoLS1010ChassisBkplType 1.3.6.1.4.1.9.5.11.1.1.2
The chassis backplane type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), atm(2), c5500(3), cisco6400(4), c8510(5), c8540(6), tgx8750(7), cat6000(8), c2948g(9), c4908g(10)  

ciscoLS1010ChassisPs0Type 1.3.6.1.4.1.9.5.11.1.1.3
Type of power supply number 1.
Status: current Access: read-only
OBJECT-TYPE    
  PsType  

ciscoLS1010ChassisPs0AdminStatus 1.3.6.1.4.1.9.5.11.1.1.4
Enable or disable power supply 1.
Status: current Access: read-write
OBJECT-TYPE    
  AdminStatus  

ciscoLS1010ChassisPs0Status 1.3.6.1.4.1.9.5.11.1.1.5
Status of power supply number 1.
Status: current Access: read-only
OBJECT-TYPE    
  OperStatus  

ciscoLS1010ChassisPs0Led 1.3.6.1.4.1.9.5.11.1.1.6
LED Status of power supply number 1.
Status: current Access: read-only
OBJECT-TYPE    
  Led  

ciscoLS1010ChassisPs1Type 1.3.6.1.4.1.9.5.11.1.1.7
Type of power supply number 2.
Status: current Access: read-only
OBJECT-TYPE    
  PsType  

ciscoLS1010ChassisPs1AdminStatus 1.3.6.1.4.1.9.5.11.1.1.8
Enable or disable power supply 2.
Status: current Access: read-write
OBJECT-TYPE    
  AdminStatus  

ciscoLS1010ChassisPs1Status 1.3.6.1.4.1.9.5.11.1.1.9
Status of power supply number 2.
Status: current Access: read-only
OBJECT-TYPE    
  OperStatus  

ciscoLS1010ChassisPs1Led 1.3.6.1.4.1.9.5.11.1.1.10
LED Status of power supply number 2.
Status: current Access: read-only
OBJECT-TYPE    
  Led  

ciscoLS1010ChassisFanStatus 1.3.6.1.4.1.9.5.11.1.1.11
Status of the chassis fan.
Status: current Access: read-only
OBJECT-TYPE    
  OperStatus  

ciscoLS1010ChassisFanLed 1.3.6.1.4.1.9.5.11.1.1.12
LED Status of fan.
Status: current Access: read-only
OBJECT-TYPE    
  Led  

ciscoLS1010ChassisCardStatusLed 1.3.6.1.4.1.9.5.11.1.1.13
LED Status of CPU card.
Status: current Access: read-only
OBJECT-TYPE    
  Led  

ciscoLS1010ChassisEnetLinkLed 1.3.6.1.4.1.9.5.11.1.1.14
Ethernet link status LED of CPU card.
Status: current Access: read-only
OBJECT-TYPE    
  Led  

ciscoLS1010Chassis12VoltStatus 1.3.6.1.4.1.9.5.11.1.1.15
The chassis 12V status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), outOfTolerance(2), unknown(3)  

ciscoLS1010ChassisTempStatus 1.3.6.1.4.1.9.5.11.1.1.16
The chassis temperature status. The values of minorWarning(3), majorWarning(4) and criticalWarning(5) will be primarily used by C6400 to indicate the core temperature. C6400 will never report overTemperature(2) status. In C6400 there are two temperature sensors: core and inlet. C6400 use this object to represent the core temperature and the other object ciscoLS1010ChassisInletTempStatus to represent the inlet temperature.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), overTemperature(2), minorWarning(3), majorWarning(4), criticalWarning(5)  

ciscoLS1010ChassisPcmciaSlot0Type 1.3.6.1.4.1.9.5.11.1.1.17
Type of PCMCIA slot 0 type.
Status: current Access: read-only
OBJECT-TYPE    
  PcmciaType  

ciscoLS1010ChassisPcmciaSlot1Type 1.3.6.1.4.1.9.5.11.1.1.18
Type of PCMCIA slot 1 type.
Status: current Access: read-only
OBJECT-TYPE    
  PcmciaType  

ciscoLS1010ChassisNumSlots 1.3.6.1.4.1.9.5.11.1.1.19
The number of slots in the chassis for plug-in modules.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

ciscoLS1010ChassisLastChange 1.3.6.1.4.1.9.5.11.1.1.20
The last time chassis physical content get changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

ciscoLS1010ChassisFailureAction 1.3.6.1.4.1.9.5.11.1.1.21
The action to take when there is any chassis failure, which includes either power supply, voltage, temperature and fan failure.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nothing(1), sendTrap(2), shutdown(3), sendTrapAndShutdown(4)  

ciscoLS1010ChassisChangeAction 1.3.6.1.4.1.9.5.11.1.1.22
The action to take when there is any chassis change, which includes either power supply, fan and boards.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nothing(1), sendTrap(2)  

ciscoLS1010ChassisClockingMode 1.3.6.1.4.1.9.5.11.1.1.23
The clocking mode of the ls1010 system. By default, the mode is non-revertive, which means that the clock will stick to the current priority, even though higher priority clock is available.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER revertive(1), nonRevertive(2)  

ciscols1010SystemClockSourceStatus 1.3.6.1.4.1.9.5.11.1.1.24
The network clock source status of 'system' source: 'notSelected' indicates 'system' not selected as the network clock source. 'selected' indicates ASP freerunning(system) is selected as network clock source.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSelected(1), selected(2)  

ciscols1010SystemClockSourcePriority 1.3.6.1.4.1.9.5.11.1.1.25
The highest priority at which 'system' is configured as a network clock source.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER priority1(1), priority2(2), priority3(3), priority4(4), priority5(5)  

ciscoLS1010ChassisInletTempStatus 1.3.6.1.4.1.9.5.11.1.1.26
C6400 has two temperature sensors: core and inlet. C6400 use this object to represent the inlet temperature and use the object ciscoLS1010ChassisTempStatus to represent the core temperature.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), overTemperature(2), minorWarning(3), majorWarning(4), criticalWarning(5), unknown(6)  

ciscoLS1010ModuleTable 1.3.6.1.4.1.9.5.11.1.2.1
A list of module entries. The number of entries is given by the value of ciscoLS1010ChassisNumSlots.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CiscoLS1010ModuleEntry

ciscoLS1010ModuleEntry 1.3.6.1.4.1.9.5.11.1.2.1.1
Entry containing information about one module in a slot of the chassis.
Status: current Access: not-accessible
OBJECT-TYPE    
  CiscoLS1010ModuleEntry  

ciscoLS1010ModuleIndex 1.3.6.1.4.1.9.5.11.1.2.1.1.1
A unique value for each module.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..15  

ciscoLS1010ModuleType 1.3.6.1.4.1.9.5.11.1.2.1.1.2
The type of module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), carrier(2), cpuSwitchAndFeature(3), cpuSwitchAndFeaturePFQ(4), superCarrier(5), cpuRoute(6), switch10GAndFC(7), switch10GNoFC(8), atmFabricIntegration(9), dualSlot(10), cmpmCarrier(11), tsCarrier(12), nodeSwitchProcessor2ndGeneration(13)  

ciscoLS1010ModuleSerialNumber 1.3.6.1.4.1.9.5.11.1.2.1.1.3
The serial number of the module. Deprecated in favor of object ciscoLS1010ModuleSerialNumberString. This object returns 0 for modules using an alphanumeric numbering scheme.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

ciscoLS1010ModuleHwVersion 1.3.6.1.4.1.9.5.11.1.2.1.1.4
The hardware version of the module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ciscoLS1010ModuleSwVersion 1.3.6.1.4.1.9.5.11.1.2.1.1.5
The software version number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ciscoLS1010ModuleDescr 1.3.6.1.4.1.9.5.11.1.2.1.1.6
A descriptive string used by the agent to describe the module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

ciscoLS1010ModuleNumSubModules 1.3.6.1.4.1.9.5.11.1.2.1.1.7
The max number of sub-modules supported by this module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

ciscoLS1010ModuleAdminStatus 1.3.6.1.4.1.9.5.11.1.2.1.1.8
This object, when read, always returns a value of ok(1). Setting this object to one of the acceptable values gives the following results: reset: reset the module's control logic enable: enable the module disable: disable the module Setting this object to any other values results in an error.
Status: current Access: read-write
OBJECT-TYPE    
  AdminStatus  

ciscoLS1010ModuleOperStatus 1.3.6.1.4.1.9.5.11.1.2.1.1.9
Operational status of the module.
Status: current Access: read-only
OBJECT-TYPE    
  OperStatus  

ciscoLS1010ModuleHwVersionMinor 1.3.6.1.4.1.9.5.11.1.2.1.1.10
The minor hardware version of the module.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ciscoLS1010ModuleSerialNumberString 1.3.6.1.4.1.9.5.11.1.2.1.1.11
The serial number of the module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

ciscoLS1010SubModuleTable 1.3.6.1.4.1.9.5.11.1.3.1
A list of sub-module entries. The number of entries is given by the value of ciscoLS1010SlotNumSubModules.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CiscoLS1010SubModuleEntry

ciscoLS1010SubModuleEntry 1.3.6.1.4.1.9.5.11.1.3.1.1
Entry containing information about one sub-module in a sub-slot of the module.
Status: current Access: not-accessible
OBJECT-TYPE    
  CiscoLS1010SubModuleEntry  

ciscoLS1010SubModuleIndex 1.3.6.1.4.1.9.5.11.1.3.1.1.1
A unique value for each sub-module within the module. This value is determined by sub-slot number where the sub-module is inserted.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..15  

ciscoLS1010SubModuleType 1.3.6.1.4.1.9.5.11.1.3.1.1.2
The type of sub-module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), oc3Utp5(2), oc3SingleModeFiber(3), oc3MultiModeFiber(4), oc12SingleModeFiber(5), oc12MultiModeFiber(6), ds3(7), e3(8), cpuSwitch(9), featureFpga(10), featureAsic(11), t1(12), e1(13), e1bnc(14), oc3Mixed(15), cbrt1(16), cbr120e1(17), cbr75e1(18), quadDs3(19), quadE3(20), dualDs3(21), dualE3(22), oc12Mixed(23), atm25(24), featurePVC(25), routerProcessorAlpha(26), dualOC3SingleModeIRFiber(27), dualOC3MultiModeIRFiber(28), routerProcessorBeta(29), fratm1CT3(30), fratm4CE1(31), oc3SingleModeLRFiber(35), oc12SingleModeLRFiber(36), sixPortDS3(37), feUTP8p16k(40), feUTP8p64k(41), feMMF8p16k(42), feMMF8p64k(43), feUTP16p16k(44), feUTP16p64k(45), feMMF16p16k(46), feMMF16p64k(47), geF1p16k(48), geF1p64k(49), geF2p16k(50), geF2p64k(51), feBridge4p(52), feUTP8p16kFullDup(53), feUTP8p64kFullDup(54), routeProc(55), switch10GProc(56), featureNetClock(57), featureABR(58), geF8p64k(59), featureLite(60), s16pOC3MM(61), s16pOC3SM(62), s4pOC12MM(63), s4pOC12SM(64), atmIma8pT1(65), atmIma8pE1(66), atm25m4p(67), s1pOC48cSM(68), s1pOC48cSMLR(69), atmFIMBridge(70), atmFIMoc12MM(71), arm1p64k(80), arm2p64k(81), xpif1pGE16k(82), xpif1pGE64k(83), xpif1pGE256k(84), xpifAtm1pOC12SMIR64k(85), xpifAtm1pOC12SMIR256k(86), xpifAtm1pOC12MM64k(87), xpifAtm1pOC12MM256k(88), xpifAtm1pOC3SMIR64k(89), xpifAtm1pOC3SMIR256k(90), xpifAtm1pOC3MM64k(91), xpifAtm1pOC3MM256k(92), xpifPos1pOC12SMIR64k(93), xpifPos1pOC12SMIR256k(94), xpifPos1pOC12SMLR64k(95), xpifPos1pOC12SMLR256k(96), xpifArm2p256k(97), aclDaughter(98)  

ciscoLS1010SubModuleSerialNumber 1.3.6.1.4.1.9.5.11.1.3.1.1.3
The serial number of the sub-module. Deprecated in favor of object ciscoLS1010SubModuleSerialNumberString. This object returns 0 for submodules using an alphanumeric numbering scheme.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

ciscoLS1010SubModuleHwVersion 1.3.6.1.4.1.9.5.11.1.3.1.1.4
The major hardware version of the sub-module. Together with ciscoLS1010SubModuleHwVersionMinor, this completely specifies the hardware version of the sub-module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ciscoLS1010SubModuleSwVersion 1.3.6.1.4.1.9.5.11.1.3.1.1.5
The software version number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ciscoLS1010SubModuleDescr 1.3.6.1.4.1.9.5.11.1.3.1.1.6
A descriptive string used by the agent to describe the module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

ciscoLS1010SubModuleNumPorts 1.3.6.1.4.1.9.5.11.1.3.1.1.7
The maximum number of ports supported by this sub-module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

ciscoLS1010SubModuleAdminStatus 1.3.6.1.4.1.9.5.11.1.3.1.1.8
This object can be read/written as reset or ok.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), ok(2)  

ciscoLS1010SubModuleHwVersionMinor 1.3.6.1.4.1.9.5.11.1.3.1.1.9
The minor hardware version of the sub-module. Together with ciscoLS1010SubModuleHwVersion, this completely specifies the hardware version of the sub-module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ciscoLS1010SubModuleOperStatus 1.3.6.1.4.1.9.5.11.1.3.1.1.10
Operational status of the submodule.
Status: current Access: read-only
OBJECT-TYPE    
  OperStatus  

ciscoLS1010SubModuleSerialNumberString 1.3.6.1.4.1.9.5.11.1.3.1.1.11
The serial number of the sub-module.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

ciscoLS1010PortTable 1.3.6.1.4.1.9.5.11.1.4.1
A list of port entries. The number of entries is determined by the number of modules in the chassis, the number of sub-module in the module and the number of ports on each sub-module.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CiscoLS1010PortEntry

ciscoLS1010PortEntry 1.3.6.1.4.1.9.5.11.1.4.1.1
Entry containing information for a particular port on a sub-module.
Status: current Access: not-accessible
OBJECT-TYPE    
  CiscoLS1010PortEntry  

ciscoLS1010PortIndex 1.3.6.1.4.1.9.5.11.1.4.1.1.1
An index value that uniquely identifies this port within a sub-module. The value is determined by the location of the port on the sub-module. Valid entries are 1 to the value of subModuleNumPorts for this sub-module.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..255  

ciscoLS1010PortIfIndex 1.3.6.1.4.1.9.5.11.1.4.1.1.2
The ifIndex value assigned to this port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

clsEnetPortTable 1.3.6.1.4.1.9.5.11.1.6.1
A list of ethernet port entries. This table is mainly to support ethernet port only.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClsEnetPortEntry

clsEnetPortEntry 1.3.6.1.4.1.9.5.11.1.6.1.1
Entry contains information of a particular ethernet port.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClsEnetPortEntry  

clsEnetPortDuplex 1.3.6.1.4.1.9.5.11.1.6.1.1.1
Indicates whether the port is operating in half-duplex, full-duplex, or auto mode. If the port could not agree with the far end on port duplex, the port will be in auto(2) mode. Unknown(1) indicates either the port does not support duplex mode, or the duplex mode is none of the defined.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), auto(2), half(3), full(4)  

clsEnetPortAdminSpeed 1.3.6.1.4.1.9.5.11.1.6.1.1.2
Indicates the desired speed of the port in bits per second. The current operational speed of the port is determined by ifSpeed. If the port could not agree with the far end on port speed, the port will be in auto(2) mode, which will force the port to transmit in speed whichever is lower. Unknown(1) indicates either the port does not support admin speed, or the admin speed is none of the defined.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), auto(2), e10Mbps(3), e100Mbps(4), e1000Mbps(5)  

clsEnetPortType 1.3.6.1.4.1.9.5.11.1.6.1.1.3
The type of physical layer medium-dependent interface on the port. unknown(1) indicates that the port type is none of those defined. empty(6) indicates that the port is not present.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), e100BaseTX(2), e100BaseFX(3), e1000BaseLX(4), e1000BaseSX(5), empty(6)  

clsEnetPortLinkStatus 1.3.6.1.4.1.9.5.11.1.6.1.1.4
This object indicates how the link status of the port came up. autoNegotiate(2) -- the port will try to negotiate the link with the partner port. If successful, the link will come up, otherwise the link will remain down. forceUp(3) -- the port will force the link up irrespective of its partner port. This will bring up the link in full duplex only. Default is autoNegotiate(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), autoNegotiate(2), forceUp(3)  

clsPortLedTable 1.3.6.1.4.1.9.5.11.1.7.1
A list of LED entries associated with a port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClsPortLedEntry

clsPortLedEntry 1.3.6.1.4.1.9.5.11.1.7.1.1
Entry contains information of a particular LED associated with a particular port which is identified by ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClsPortLedEntry  

clsPortLedIndex 1.3.6.1.4.1.9.5.11.1.7.1.1.1
An index that uniquely identifies this LED among all the LEDs associated with the port identified by ifIndex. This value is related to the physical location of the LED, and is in ascending order from top to bottom, left to right.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..255  

clsPortLedType 1.3.6.1.4.1.9.5.11.1.7.1.1.2
Indicates the type or label of the LED.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ledTx(1), ledRx(2), ledLink(3), led100Mbps(4), ledRxLoss(5), ledRxFullOut(6), ledRxSync(7), ledFullDuplex(8), ledOptDetect(9)  

clsPortLedStatus 1.3.6.1.4.1.9.5.11.1.7.1.1.3
Indicates the status of the LED. Unknown(1) indicates either the LED status is not supported or the status is none of the defined.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), on(2), off(3)  

ciscoAtmCpuAdminStatus 1.3.6.1.4.1.9.5.11.1.5.1
Reset will reload the CPU board.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), ok(2)  

ciscoAtmSwitchTotalBuffer 1.3.6.1.4.1.9.5.11.1.5.2
The total cell buffer count in switch's shared memory.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ciscoAtmSwitchFreeBuffer 1.3.6.1.4.1.9.5.11.1.5.3
The free cell buffer count in switch's shared memory.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

ciscoAtmSwitchDiscardCells 1.3.6.1.4.1.9.5.11.1.5.4
The total discarded cells of the switch.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ciscoAtmSwitchInvalidCells 1.3.6.1.4.1.9.5.11.1.5.5
The total invalid cells of the switch.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ciscoAtmSwitchInvalidCellHeaderTable 1.3.6.1.4.1.9.5.11.1.5.6
A list of invalid cell header entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CiscoAtmSwitchInvalidCellHeaderEntry

ciscoAtmSwitchInvalidCellHeaderEntry 1.3.6.1.4.1.9.5.11.1.5.6.1
a entry of invalid cell header.
Status: current Access: not-accessible
OBJECT-TYPE    
  CiscoAtmSwitchInvalidCellHeaderEntry  

ciscoAtmSwitchInvalidCellHeaderIndex 1.3.6.1.4.1.9.5.11.1.5.6.1.1
A sequence number that identifies a invalid cell header entry in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..64  

ciscoAtmSwitchInvalidCellHeader 1.3.6.1.4.1.9.5.11.1.5.6.1.2
The most recently received invalid cells header. octet 0 is port number (0-32), octet 1 bit 7-5 is PTI, octet 1 bit 4 is CLP, octet 1 bit 3-0 is GFC, octet 2 is VPI, octet 3 is high byte of VCI octet 4 is low byte of VCI.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(5)  

ciscoAtmCpuTerminateOamFlow 1.3.6.1.4.1.9.5.11.1.5.7
Terminate all the incoming OAM cells to the CPU port.
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

ciscoAtmInterceptEndToEndOamFlow 1.3.6.1.4.1.9.5.11.1.5.8
Indicates whether incoming end-to-end OAM flow cells are sent to the switch CPU. If the value is 'true', all incoming end-to-end OAM flow cells, including those on transit connections, are sent to the switch CPU. This value may be modified at any time. The modified value will apply to all existing connections. Note that if the value is 'false', the switch can not use the ATM PING application for end-to-end loopback on transit connections, since the end-to-end OAM cells on such connections will not be seen by the switch CPU.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ciscoLS1010ChassisMIBNotificationPrefix 1.3.6.1.4.1.9.5.11.2
OBJECT IDENTIFIER    

ciscoLS1010ChassisMIBNotifications 1.3.6.1.4.1.9.5.11.2.0
OBJECT IDENTIFIER    

ciscoLS1010ChassisFailureNotification 1.3.6.1.4.1.9.5.11.2.0.1
Agent detects a change in the status of ps0, ps1, fan, 12V line, and/or chassis temperature. This notification will be generated when the status changes from no-fault to fault, and also when the status changes from fault to no-fault.
Status: current Access: read-write
NOTIFICATION-TYPE    

ciscoLS1010ChassisChangeNotification 1.3.6.1.4.1.9.5.11.2.0.2
Agent detects any hot-swap component change or changes in the chassis.
Status: current Access: read-write
NOTIFICATION-TYPE    

ciscoLS1010ChassisMIBConformance 1.3.6.1.4.1.9.5.11.3
OBJECT IDENTIFIER    

ciscoLS1010ChassisMIBCompliances 1.3.6.1.4.1.9.5.11.3.1
OBJECT IDENTIFIER    

ciscoLS1010ChassisMIBGroups 1.3.6.1.4.1.9.5.11.3.2
OBJECT IDENTIFIER    

ciscoLS1010ChassisMIBCompliance 1.3.6.1.4.1.9.5.11.3.1.1
The compliance statement for entities which implement the Cisco LS1010 Chassis MIB. This statement was obsoleted by ciscoLS1010ChassisMIBComplianceRev1.
Status: obsolete Access: read-write
MODULE-COMPLIANCE    

ciscoLS1010ChassisMIBComplianceRev1 1.3.6.1.4.1.9.5.11.3.1.2
The compliance statement for entities which implement the Cisco LS1010 Chassis MIB. This statement was obsoleted by ciscoLS1010ChassisMIBComplianceRev2.
Status: obsolete Access: read-write
MODULE-COMPLIANCE    

ciscoLS1010ChassisMIBComplianceRev2 1.3.6.1.4.1.9.5.11.3.1.3
The compliance statement for entities which implement the Cisco LS1010 Chassis MIB
Status: obsolete Access: read-write
MODULE-COMPLIANCE    

ciscoLS1010ChassisMIBComplianceRev3 1.3.6.1.4.1.9.5.11.3.1.4
The compliance statement for entities which implement the Cisco LS1010 Chassis MIB.
Status: obsolete Access: read-write
MODULE-COMPLIANCE    

ciscoLS1010ChassisMIBComplianceRev4 1.3.6.1.4.1.9.5.11.3.1.5
The compliance statement for entities which implement the Cisco LS1010 Chassis MIB.
Status: obsolete Access: read-write
MODULE-COMPLIANCE    

ciscoLS1010ChassisMIBComplianceRev5 1.3.6.1.4.1.9.5.11.3.1.6
The compliance statement for the Cisco 6400 product.
Status: obsolete Access: read-write
MODULE-COMPLIANCE    

ciscoLS1010ChassisMIBComplianceRev6 1.3.6.1.4.1.9.5.11.3.1.7
The compliance statement for this MIB.
Status: current Access: read-write
MODULE-COMPLIANCE    

ciscoLS1010ChassisMIBGroup 1.3.6.1.4.1.9.5.11.3.2.1
A collection of objects providing rhino chassis information
Status: obsolete Access: read-write
OBJECT-GROUP    

ciscoLS1010ChassisMIBObsoleteGroup 1.3.6.1.4.1.9.5.11.3.2.2
A collection of objects providing rhino chassis information which are obsolete.
Status: obsolete Access: read-write
OBJECT-GROUP    

ciscoLS1010ChassisMIBRev1Group 1.3.6.1.4.1.9.5.11.3.2.3
A collection of objects useful for reporting the hardware version of sub-modules in the chassis.
Status: current Access: read-write
OBJECT-GROUP    

ciscoLS1010ChassisMIBClockingGroup 1.3.6.1.4.1.9.5.11.3.2.4
A collection of objects useful for managing clocking.
Status: current Access: read-write
OBJECT-GROUP    

ciscoLS1010ChassisMIBGroup1 1.3.6.1.4.1.9.5.11.3.2.5
A collection of objects for managing the LS1010 chassis.
Status: obsolete Access: read-write
OBJECT-GROUP    

clsEnetPortGroup1 1.3.6.1.4.1.9.5.11.3.2.6
A collection of objects for managing ethernet ports.
Status: current Access: read-write
OBJECT-GROUP    

clsPortLedGroup1 1.3.6.1.4.1.9.5.11.3.2.7
A collection of objects for showing port LEDs.
Status: current Access: read-write
OBJECT-GROUP    

clsOperStatusGroup 1.3.6.1.4.1.9.5.11.3.2.8
A collection of objects for displaying operational status of modules and sub-modules in the chassis.
Status: current Access: read-write
OBJECT-GROUP    

clsInletTempGroup 1.3.6.1.4.1.9.5.11.3.2.9
A collection of objects for reporting inlet temperature.
Status: current Access: read-write
OBJECT-GROUP    

ciscoLS1010ChassisMIBGroup2 1.3.6.1.4.1.9.5.11.3.2.10
A collection of objects for managing the LS1010 chassis.
Status: current Access: read-write
OBJECT-GROUP    

ciscoLS1010ChassisMIBDeprecatedGroup 1.3.6.1.4.1.9.5.11.3.2.11
A collection of objects providing rhino chassis information which are obsolete.
Status: deprecated Access: read-write
OBJECT-GROUP    

ciscoLS1010ChassisMIBNotificationGroup 1.3.6.1.4.1.9.5.11.3.2.12
A collection of notifications supported by LS1010 chassis.
Status: current Access: read-write
NOTIFICATION-GROUP