CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB

File: CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB.mib (28108 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
CISCO-SMI SNMP-REPEATER-MIB RFC1213-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
NOTIFICATION-TYPE MODULE-COMPLIANCE OBJECT-GROUP
TEXTUAL-CONVENTION DisplayString ciscoExperiment
rptrGroupIndex rptrPortGroupIndex rptrPortIndex
PhysAddress

Defined Types

HubNumber  
Represents the hub number that the system supports for stacking. The hub number represents the order in which a hub is stacked relative to other members of the stack. Lowest hub number represents the top member of the stack. This is also the number used in the command line interface.
TEXTUAL-CONVENTION    
  Integer32 1..2147483647  

CssGroupEntry  
SEQUENCE    
  cssGroupID HubNumber
  cssGroupType INTEGER
  cssGroupSerialNo DisplayString
  cssGroupBoardRevision Integer32
  cssGroupAgentBootVersion DisplayString
  cssGroupAgentFirmwareVersion DisplayString
  cssGroupAgentStatus INTEGER
  cssGroupAgentPhysAddress PhysAddress
  cssGroupInternalPowerState INTEGER
  cssGroupRedundantPowerState INTEGER
  cssGroupReset INTEGER
  cssGroupConfigDefaultReset INTEGER
  cssGroupIsolatedState INTEGER

CssRepeaterPortEntry  
SEQUENCE    
  cssRepeaterPortName DisplayString
  cssRepeaterPortControllerRevision Integer32
  cssRepeaterPortSpeedAdmin INTEGER
  cssRepeaterPortSpeedStatus INTEGER
  cssRepeaterPortLinkStatus INTEGER

CssSwitchPortEntry  
SEQUENCE    
  cssSwitchPortModuleID Integer32
  cssSwitchPortPortID Integer32
  cssSwitchPortName DisplayString
  cssSwitchPortType INTEGER
  cssSwitchPortControllerRevision Integer32
  cssSwitchPortState INTEGER
  cssSwitchPortDuplexAdmin INTEGER
  cssSwitchPortDuplexStatus INTEGER
  cssSwitchPortSpeedAdmin INTEGER
  cssSwitchPortSpeedStatus INTEGER
  cssSwitchPortLinkStatus INTEGER

Defined Values

ciscoSibuStackableDualSpeedHubMIB 1.3.6.1.4.1.9.10.44
The MIB module that extends the REPEATER-MIB to manage CISCO low end stackable repeater products. For the purpose of this mib, a hub is a repeater group and stack is collection of one or more hubs interconnected via stack bus connectors.
MODULE-IDENTITY    

ciscoSibuStackableDualSpeedHubMIBObjects 1.3.6.1.4.1.9.10.44.1
OBJECT IDENTIFIER    

cssSystem 1.3.6.1.4.1.9.10.44.1.1
OBJECT IDENTIFIER    

cssGroup 1.3.6.1.4.1.9.10.44.1.2
OBJECT IDENTIFIER    

cssRepeaterPort 1.3.6.1.4.1.9.10.44.1.3
OBJECT IDENTIFIER    

cssSwitchPort 1.3.6.1.4.1.9.10.44.1.4
OBJECT IDENTIFIER    

cssSystemLinkTraps 1.3.6.1.4.1.9.10.44.1.1.1
Indicates whether the stack is permitted to generate linkUp/linkDown traps for both repeater port and switch module's port. The stack provides only a single global control of link traps in contrast to per interface control provided by IF-MIB. The value of all instances ifLinkUpDownTrapEnable is set to TRUE (FALSE) if this object is set to enabled (disabled). The object ifLinkUpDownTrapEnable is read-only. A linkUp/linkDown trap is generated whenever a port's link STATUS or administrative status changes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cssGroupTable 1.3.6.1.4.1.9.10.44.1.2.1
A list of member hubs in the stack.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CssGroupEntry

cssGroupEntry 1.3.6.1.4.1.9.10.44.1.2.1.1
Configuration parameters for an individual hub. An entry is created by default for the master unit in the stack. A entry is created (removed) when a hub is connected to (removed from) the stack.
Status: current Access: not-accessible
OBJECT-TYPE    
  CssGroupEntry  

cssGroupID 1.3.6.1.4.1.9.10.44.1.2.1.1.1
The hub identifier of unit in a stack.
Status: current Access: read-only
OBJECT-TYPE    
  HubNumber  

cssGroupType 1.3.6.1.4.1.9.10.44.1.2.1.1.2
The model type of the hub unit
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cisco1538MDS(1), cisco1538UDS(2), wsC412M(3), wsC412(4), wsC424M(5), wsC424(6)  

cssGroupSerialNo 1.3.6.1.4.1.9.10.44.1.2.1.1.4
Serial number of the hardware.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

cssGroupBoardRevision 1.3.6.1.4.1.9.10.44.1.2.1.1.5
Hardware version of the repeater board.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

cssGroupAgentBootVersion 1.3.6.1.4.1.9.10.44.1.2.1.1.6
Returns the version number of the dual-speed hub BOOT software residing in flash. The format is 'V1.2.3'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

cssGroupAgentFirmwareVersion 1.3.6.1.4.1.9.10.44.1.2.1.1.7
Returns the version number of the dual-speed hub firmware residing in flash. The format is 'V1.2.3'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

cssGroupAgentStatus 1.3.6.1.4.1.9.10.44.1.2.1.1.8
Status of this hub agent. Each stack allows only one SNMP primary agent. notPresent(1): The hub does not have an agent. primary(2): The agent of this hub is a primary agent. backup(3) : The agent of this hub is a backup agent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notPresent(1), primary(2), backup(3)  

cssGroupAgentPhysAddress 1.3.6.1.4.1.9.10.44.1.2.1.1.9
MAC address of this hub's agent
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

cssGroupInternalPowerState 1.3.6.1.4.1.9.10.44.1.2.1.1.12
Indicates the state of the internal power supply. off : The internal power supply is off. on : The internal power supply is on.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

cssGroupRedundantPowerState 1.3.6.1.4.1.9.10.44.1.2.1.1.13
Indicates the state of the external/backup power supply. off : the switch is not connected to a redundant power source. healthy : a redundant power source is connected to the switch and the power source is operating correctly. faulty : a redundant power source is connected to the switch but a failure exists in the power system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(1), healthy(2), faulty(3)  

cssGroupReset 1.3.6.1.4.1.9.10.44.1.2.1.1.14
Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). Setting this object to noReset(1) has no effect. The switch always returns the value noReset(1) when this object is read.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noReset(1), reset(2)  

cssGroupConfigDefaultReset 1.3.6.1.4.1.9.10.44.1.2.1.1.15
Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). All configuration parameters will revert to their factory default settings. Setting this object to noReset(1) has no effect. The switch always returns the value noReset(1) when this object is read.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noReset(1), reset(2)  

cssGroupIsolatedState 1.3.6.1.4.1.9.10.44.1.2.1.1.16
Setting this object to isolated(1) causes this hub to be isolated from the back plane bus. Setting this object to attached(2) causes this hub to be attached to the back plane bus.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER isolated(1), attached(2)  

cssRepeaterPortTable 1.3.6.1.4.1.9.10.44.1.3.1
The list of repeater port configurations on each hub unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CssRepeaterPortEntry

cssRepeaterPortEntry 1.3.6.1.4.1.9.10.44.1.3.1.1
Configuration parameters for an individual repeater port on a hub. The value of rptrPortIndex also indicates the physical port number of the port in the hub. An entry is created for each repeater port in a hub when the hub is connected to the stack. The corresponding entries are removed when the hub is removed from the stack.
Status: current Access: not-accessible
OBJECT-TYPE    
  CssRepeaterPortEntry  

cssRepeaterPortName 1.3.6.1.4.1.9.10.44.1.3.1.1.1
A descriptive string of up to 20 characters used by the network administrator to name a port.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

cssRepeaterPortControllerRevision 1.3.6.1.4.1.9.10.44.1.3.1.1.2
Returns the revision number of the port controller.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

cssRepeaterPortSpeedAdmin 1.3.6.1.4.1.9.10.44.1.3.1.1.3
Set to tenMbps(1) to operate in 10Mbps speed mode. Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to negotiate with the other end of the connection. The actual operating speed of the port is given by cssRepeaterPortSpeedStatus.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tenMbps(1), oneHundredMbps(2), autoNegotiate(3)  

cssRepeaterPortSpeedStatus 1.3.6.1.4.1.9.10.44.1.3.1.1.4
The operating speed of the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tenMbps(1), oneHundredMbps(2)  

cssRepeaterPortLinkStatus 1.3.6.1.4.1.9.10.44.1.3.1.1.5
The current port link status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER link(1), noLink(2)  

cssSwitchPortTable 1.3.6.1.4.1.9.10.44.1.4.1
A list of switched ports on extension module on a each hub unit in the stack.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CssSwitchPortEntry

cssSwitchPortEntry 1.3.6.1.4.1.9.10.44.1.4.1.1
Configuration parameters for an individual switch module port. An entry is created for each switch port on a module is inserted into a hub in the stack. The corresponding entries are removed when the module is removed from the hub in the stack, or if the hub is removed from the stack.
Status: current Access: not-accessible
OBJECT-TYPE    
  CssSwitchPortEntry  

cssSwitchPortModuleID 1.3.6.1.4.1.9.10.44.1.4.1.1.1
Unique ID number of a module unit in a hub as used in the command line interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

cssSwitchPortPortID 1.3.6.1.4.1.9.10.44.1.4.1.1.2
The unique ID identifying a port on an extension module on a hub as used in the command line interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

cssSwitchPortName 1.3.6.1.4.1.9.10.44.1.4.1.1.3
A descriptive string of up to 20 characters used by the network administrator to name a switch port.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

cssSwitchPortType 1.3.6.1.4.1.9.10.44.1.4.1.1.4
Type of switch module in this hub.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER wsX4001(1), wsX4002(2)  

cssSwitchPortControllerRevision 1.3.6.1.4.1.9.10.44.1.4.1.1.5
The revision number of the port controller.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

cssSwitchPortState 1.3.6.1.4.1.9.10.44.1.4.1.1.6
Setting this object to enabled(1) enables the port. Setting this object to disabled(2) disables the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cssSwitchPortDuplexAdmin 1.3.6.1.4.1.9.10.44.1.4.1.1.7
Set to fullDuplex(1) to operate in full duplex mode: port will allow simultaneous transmit and receive which can double its bandwidth. Set to halfDuplex(2) to operate in normal mode. Set to autoNegotiate(3) to allow the switch to negotiate the duplex status with the other end of the connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fullDuplex(1), halfDuplex(2), autoNegotiate(3)  

cssSwitchPortDuplexStatus 1.3.6.1.4.1.9.10.44.1.4.1.1.8
The operating duplex mode of the switched port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER fullDuplex(1), halfDuplex(2)  

cssSwitchPortSpeedAdmin 1.3.6.1.4.1.9.10.44.1.4.1.1.9
Set to tenMbps(1) to operate in 10Mbps speed mode. Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to negotiate the operating speed with the other end of the connection. If the value of object cssSwitchPortType is WS-X4002(2), this object will be read-only, because FX module only supports 100Mbps speed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tenMbps(1), oneHundredMbps(2), autoNegotiate(3)  

cssSwitchPortSpeedStatus 1.3.6.1.4.1.9.10.44.1.4.1.1.10
The operating speed of the switched port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER tenMbps(1), oneHundredMbps(2)  

cssSwitchPortLinkStatus 1.3.6.1.4.1.9.10.44.1.4.1.1.11
Indicates the link STATUS of switch port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER link(1), noLink(2)  

ciscoSibuStackableDualSpeedHubNotifications 1.3.6.1.4.1.9.10.44.2
OBJECT IDENTIFIER    

ciscoSibuStackableDualSpeedHubNotificationsPrefix 1.3.6.1.4.1.9.10.44.2.0
OBJECT IDENTIFIER    

ciscoSibuStackableDualSpeedHubRptrPortLinkChange 1.3.6.1.4.1.9.10.44.2.0.1
This trap is generated whenever the value of cssRepeaterPortLinkStatus changes for a repeater port.
Status: current Access: read-only
NOTIFICATION-TYPE    

ciscoSibuStackableDualSpeedHubSwitchPortLinkChange 1.3.6.1.4.1.9.10.44.2.0.2
This trap is generated whenever the value of cssSwitchPortLinkStatus changes for a switch port on an extension module.
Status: current Access: read-only
NOTIFICATION-TYPE    

ciscoSibuStackableDualSpeedHubMIBComformance 1.3.6.1.4.1.9.10.44.3
OBJECT IDENTIFIER    

ciscoSibuStackableDualSpeedHubMIBCompliances 1.3.6.1.4.1.9.10.44.3.1
OBJECT IDENTIFIER    

ciscoSibuStackableDualSpeedHubMIBGroups 1.3.6.1.4.1.9.10.44.3.2
OBJECT IDENTIFIER    

ciscoSibuStackableDualSpeedHubCompliance 1.3.6.1.4.1.9.10.44.3.1.1
The compliance statement for the Cisco Stackable Dual-Speed Hub products.
Status: current Access: read-only
MODULE-COMPLIANCE    

ciscoSibuStackableDualSpeedHubGroup 1.3.6.1.4.1.9.10.44.3.2.1
A collection of group objects for use with the Cisco Stackable Dual-Speed Hub products.
Status: current Access: read-only
OBJECT-GROUP    

ciscoSibuStackableDualSpeedHubRepeaterPortGroup 1.3.6.1.4.1.9.10.44.3.2.2
A collection of repeater port objects for use with the Cisco Stackable Dual-Speed Hub products.
Status: current Access: read-only
OBJECT-GROUP    

ciscoSibuStackableDualSpeedHubSwitchPortGroup 1.3.6.1.4.1.9.10.44.3.2.3
A collection of switch module port objects for use with the Cisco Stackable Dual-Speed Hub products.
Status: current Access: read-only
OBJECT-GROUP