CISCO-VISM-TRAPS-MIB
File:
CISCO-VISM-TRAPS-MIB.mib (81160 bytes)
Imported modules
Imported symbols
Defined Values
| trapVismIpAddressChanged |
50700 |
| Sent when the card's IP address is changed.
vismIpAddress contains the new IP address. |
| TRAP-TYPE |
|
|
|
| trapVismChanActive |
50709 |
| Sent when a channel becomes active.
genericLineNum is always set to 0 on the VISM card
since it is not applicable to VISM.
vismCnfChanNum specifies the channel number and
vismChanPortNum specifies the port number where the channel
is configured. |
| TRAP-TYPE |
|
|
|
| trapVismChanDeleted |
50710 |
| Sent when a channel is deleted.
genericLineNum is always set to 0 on the VISM card
since it is not applicable to VISM.
vismCnfChanNum specifies the channel number and
vismChanPortNum specifies the port number where the channel
is configured. |
| TRAP-TYPE |
|
|
|
| trapVismPortAdded |
50711 |
| Indicates that a port with port number vismPortNum
was added with type vismPortType. |
| TRAP-TYPE |
|
|
|
| trapVismPortActive |
50712 |
| Indicates port with port number vismPortNum went active.
The type of port is specified in vismPortType. |
| TRAP-TYPE |
|
|
|
| trapVismPortFailed |
50713 |
| Indicates port with port number vismPortNum failed.
The new state of the port is specified in vismPortState. |
| TRAP-TYPE |
|
|
|
| trapProtectedChanActive |
50714 |
| Sent when the channel on port number
vismChanPortNum with a channel number
vismCnfChanNum transitions to active as
specified by vismChanActivityState . |
| TRAP-TYPE |
|
|
|
| trapProtectedChanStandby |
50715 |
| Sent when the channel on port number
vismChanPortNum with a channel number
vismCnfChanNum transitions to standby as
specified by vismChanActivityState. |
| TRAP-TYPE |
|
|
|
| trapProtectedChanFailed |
50716 |
| Sent when the channel on port number
vismChanPortNum with a channel number
vismCnfChanNum transitions to failed as
specified by vismChanActivityState. |
| TRAP-TYPE |
|
|
|
| trapProtectedChanLocked |
50717 |
| Sent when the channel on port number
vismChanPortNum with a channel number
vismCnfChanNum transitions to locked as
specified by vismChanLockingState. |
| TRAP-TYPE |
|
|
|
| trapProtectedChanUnlocked |
50718 |
| Sent when the channel on port number
vismChanPortNum with a channel number
vismCnfChanNum transitions to unlocked as
specified by vismChanLockingState. |
| TRAP-TYPE |
|
|
|
| trapVismCasVariantAdded |
50739 |
| Indicates that an entry has been added to vismCasVariantTable.
vismCasVariantName is user defined and associated with
vismCasFileName. vismCasFileName can be chosen from
predefined filenames describing a CAS protocol.
vismCasVariantState specifies whether the CAS variant is
configured or not configured.
|
| TRAP-TYPE |
|
|
|
| trapVismCasVariantDeleted |
50740 |
| Indicates that an entry with a name vismCasVariantName
has been deleted from vismCasVariantTable. |
| TRAP-TYPE |
|
|
|
| trapVismScalarChange |
50745 |
| Sent when a scalar object/objects changes.
The bit map indicates the group to which the
changed object/objects belong. For a single set
operation, a single trap will be sent per group,
regardless of how many objects got changed in
in that group. |
| TRAP-TYPE |
|
|
|
| trapVismTableChange |
50746 |
| Sent when a table config has changed.
The bit map tells which table got changed.
and vismTrapIntIndex1 shows the index of the
table entry which got changed. If there are
2 index values, the 2nd index will be contained
in vismTrapIntIndex2. If the table has a string
index, the index value will be contained in
vismTrapStrIndex1. |
| TRAP-TYPE |
|
|
|
| trapVismCodecTemplateChanged |
50743 |
| Indicates that the VISM Codec template has been changed.
vismAppliedTemplate is the new template number. |
| TRAP-TYPE |
|
|
|
| trapVismModeChanged |
50744 |
| Indicates that the mode has been changed on the card.
vismMode specifies the new mode of the card. |
| TRAP-TYPE |
|
|
|
| trapVismAal2CidAdded |
50747 |
| Indicates that a CID vismAal2CidNum
has been added to an LCN vismAal2CidLcn
thereby creating an entry in the
vismAal2CidCnfTable. |
| TRAP-TYPE |
|
|
|
| trapVismAal2CidDeleted |
50748 |
| Indicates that a CID vismAal2CidNum has been deleted
from an LCN vismAal2CidLcn thereby deleting the
corresponding entry from the table vismAal2CidCnfTable. |
| TRAP-TYPE |
|
|
|
| trapVismHdlcChanAdded |
50752 |
| Indicates that an entry with HDLC channel number
vismHdlcChanNum has been added to the table
vismHdlcChanTable. |
| TRAP-TYPE |
|
|
|
| trapVismHdlcChanDeleted |
50753 |
| Indicates that an entry with HDLC channel number
vismHdlcChanNum has been deleted from the table
vismHdlcChanTable. |
| TRAP-TYPE |
|
|
|
| trapVismPortDeleted |
50754 |
| Indicates port with port number vismPortNum
has been deleted. |
| TRAP-TYPE |
|
|
|
| trapVismChanAdded |
50755 |
| Sent when a VISM Channel is added, genericLineNum
is always set to 0 since it is not applicable
to VISM. |
| TRAP-TYPE |
|
|
|
| trapVismChanFailed |
50756 |
| Sent when a VISM Channel fails, genericLineNum
is always set to 0 since it is not applicable
to VISM. |
| TRAP-TYPE |
|
|
|
| trapVismConUp |
50758 |
| Sent when a PVC is brought up from down.
The previous vismChanRowStatus of this
channel must be outOfService. |
| TRAP-TYPE |
|
|
|
| trapVismAal2Muxing |
50760 |
| Sent when aal2 muxing type is changed.
vismAal2SubcellMuxing will represent whether subcell
muxing is enabled or disabled. |
| TRAP-TYPE |
|
|
|
| trapVismCidState |
50785 |
| Sent when there is a state change on vismAal2CidNum
in the LCN specified by vismAal2CidLcn to a new state
specified in vismAal2CidState with the reason
vismAal2CidFailReason. For example, if a PVC alarm is
generated on the remote end for vismAal2CidLcn, all
vismAal2CidNum within this LCN with transition to a
failed state as specified in vismAal2CidState. |
| TRAP-TYPE |
|
|
|
| trapVismFeatureChanged |
50790 |
| By changing the mode of the card you can change the
usable feature set on the card.
This trap is sent when the vismFeatureBitMap has been
changed on the card. |
| TRAP-TYPE |
|
|
|
| mgAdministrativeStateLocked |
50719 |
| Triggered when mgAdministrativeState transitions to locked.
The transition may be from unlocked to locked or from
'gracefulOutOfService' to locked. |
| TRAP-TYPE |
|
|
|
| mgcAssociated |
50722 |
| Triggered when mgAssociationState transitions to associated.
The transition may be from unassociated to associated or from
associatedCommLoss to associated.
The value of vismTrapIntIndex1 gives the value of mgcNumber. |
| TRAP-TYPE |
|
|
|
| mgcUnassociated |
50723 |
| Triggered when mgAssociationState transitions to Unassociated.
The transition may be from associated to Unassociated or from
associatedCommLoss to Unassociated.
The value of vismTrapIntIndex1 gives the value of mgcNumber. |
| TRAP-TYPE |
|
|
|
| mgcAssociatedCommLoss |
50724 |
| Triggered when mgAssociationState transitions from
associated to associatedCommLoss.
The value of vismTrapIntIndex1 gives the value of
mgcNumber. |
| TRAP-TYPE |
|
|
|
| mgcCommStateActive |
50725 |
| Triggered when mgcResolutionCommState transitions
from inactive to active. Indicates that an IP
address of an MGC has become active.
The value of vismTrapIntIndex1 gives the value of
mgcResolutionIndex. |
| TRAP-TYPE |
|
|
|
| mgcCommStateInactive |
50726 |
| Triggered when mgcResolutionCommState transitions from active
to inactive. Indicates that an IP address of an MGC has
become inactive. The value of vismTrapIntIndex1 gives
the value of mgcResolutionIndex. |
| TRAP-TYPE |
|
|
|
| mgEndpointCreated |
50727 |
| Triggered by creation of an endpoint.
The value of vismTrapIntIndex1 gives the value of
mgEndpointNumber. |
| TRAP-TYPE |
|
|
|
| mgEndpointDeleted |
50728 |
| Triggered by deletion of an endpoint.
The value of vismTrapIntIndex1 gives the value of
mgEndpointNumber. |
| TRAP-TYPE |
|
|
|
| mgEndpointActive |
50729 |
| Triggered when mgEndpointState transitions from
failed/degraded to active.
The value of vismTrapIntIndex1 gives the value of
mgEndpointNumber. |
| TRAP-TYPE |
|
|
|
| mgEndpointFailed |
50730 |
| Triggered when mgEndpointState transitions from
active to failed/degraded.
The value of vismTrapIntIndex1 gives the value of
mgEndpointNumber. |
| TRAP-TYPE |
|
|
|
| mgcAdded |
50731 |
| Indicates that an entry is added to mgcTable.
The value of vismTrapIntIndex1 gives the
value of mgcNumber. |
| TRAP-TYPE |
|
|
|
| mgcDeleted |
50732 |
| Indicates that an entry is deleted from mgcTable.
The value of vismTrapIntIndex1 gives the value
of mgcNumber. |
| TRAP-TYPE |
|
|
|
| mgcProtocolAdded |
50733 |
| Indicates that an entry is added to mgcProtocolTable.
The value of vismTrapIntIndex1 gives the value of mgcNumber.
The value of vismTrapIntIndex2 gives the value of
mgProtocolNumber. |
| TRAP-TYPE |
|
|
|
| mgcProtocolDeleted |
50734 |
| Indicates that an entry is deleted from mgcProtocolTable.
The value of vismTrapIntIndex1 gives the value of mgcNumber.
The value of vismTrapIntIndex2 gives the value of
mgProtocolNumber. |
| TRAP-TYPE |
|
|
|
| mgcResolutionAdded |
50735 |
| Indicates that an entry is added to mgcResolutionTable.
The value of vismTrapIntIndex1 gives the value of
mgcResolutionIndex. |
| TRAP-TYPE |
|
|
|
| mgcResolutionDeleted |
50736 |
| Indicates that an entry is deleted from mgcResolutionTable.
The value of vismTrapIntIndex1 gives the value of
mgcResolutionIndex. |
| TRAP-TYPE |
|
|
|
| peerHeartbeatLost |
50737 |
| This notification indicates that the system failed to receive
a heartbeat from a specific peer. The notification is sent
when srcpPeerTimeSinceHeartbeat crosses the
srcpPeerHeartbeatInterval threshold.
The value of vismTrapIntIndex1 gives the value of srcpPeerId. |
| TRAP-TYPE |
|
|
|
| peerHeartbeatDetected |
50738 |
| This notification indicates that the system detected
a heartbeat from a specific peer after it had been lost.
The notification is sent when srcpPeerTimeSinceHeartbeat
which had exceeded the threshold, resets to 0 due to
receipt of a heartbeat.
The value of vismTrapIntIndex1 gives the value of srcpPeerId. |
| TRAP-TYPE |
|
|
|
| trapLapdAdded |
50761 |
| Indicates that an entry has been added to
vismLapdTable with an index vismLapdIndex. |
| TRAP-TYPE |
|
|
|
| trapLapdDeleted |
50762 |
| Indicates that the entry with index vismLapdIndex
has been deleted from vismLapdTable. |
| TRAP-TYPE |
|
|
|
| trapSessionSetAdded |
50763 |
| Indicates that an entry has been added to
vismSessionSetTable. |
| TRAP-TYPE |
|
|
|
| trapSessionGrpAdded |
50765 |
| Indicates that an entry has been added to
vismSessionGrpTable. |
| TRAP-TYPE |
|
|
|
| trapRudpSessionAdded |
50767 |
| Indicates that an entry has been added to
vismRudpSessionCnfTable. |
| TRAP-TYPE |
|
|
|
| trapRudpSessionOos |
50769 |
| When a session loses communication with the MGC
the state changes to 'Out Of Service' and sends
out this trap. The severity of this trap should
be minor severity. |
| TRAP-TYPE |
|
|
|
| trapRudpSessionIs |
50770 |
| When a session state changes to 'In Service'
this trap is sent out.
The severity should be informational. |
| TRAP-TYPE |
|
|
|
| trapRudpSessionPrimaryIs |
50771 |
| This trap is sent out when the session state
is changed to 'Primary In Service'.
The severity should be informational. |
| TRAP-TYPE |
|
|
|
| trapRudpSessionActive |
50772 |
| When a 'Primary In Service' session in a group
receives active message from the MGC this trap
will be sent out.
The severity should be informational. |
| TRAP-TYPE |
|
|
|
| trapSessionGrpOos |
50773 |
| When all the sessions in the group have changed to
'Out Of Service' state, the state of this group is
changed to 'Out Of Service' and this trap will be
sent out.
The severity should be 'minor', no alarm. |
| TRAP-TYPE |
|
|
|
| trapSessionGrpIs |
50774 |
| When the state of this group is changed to 'In Service'
this trap will be sent out.
The severity should be informational. |
| TRAP-TYPE |
|
|
|
| trapSessionSetOos |
50775 |
| When the session set state is changed to
'Out Of Service' this trap will be sent out.
The severity should be 'minor', no alarm. |
| TRAP-TYPE |
|
|
|
| trapSessionSetActiveIs |
50776 |
| When the session set state is changed to
'Active In Service' state this trap will be
sent out.
The severity should be informational. |
| TRAP-TYPE |
|
|
|
| trapSessionSetStandbyIs |
50777 |
| When the session set state is changed to
'Standby In Service' state this trap will
be sent out.
The severity should be informational. |
| TRAP-TYPE |
|
|
|
| trapSessionSetFullIs |
50778 |
| When the session set state is changed from
other state to 'Full In Service' state this
trap will be sent out.
The severity should be informational. |
| TRAP-TYPE |
|
|
|
| trapLapdDlcAdded |
50779 |
| Indicates that an entry has been added to
vismLapdDlcTable. |
| TRAP-TYPE |
|
|
|
| trapLapdDlcDeleted |
50780 |
| Indicates that an entry has been deleted from
vismLapdDlcTable. |
| TRAP-TYPE |
|
|
|
| trapLapdDlcUp |
50781 |
| Indicates that the linking state between TDM and DLC on a
specific D-channel changes to up. |
| TRAP-TYPE |
|
|
|
| trapLapdDlcDown |
50782 |
| Indicates that the linking state between TDM and DLC on a
specific D-channel changes to down. |
| TRAP-TYPE |
|
|
|
| persistentXgcpEventCreated |
50786 |
| Indicates that an entry is added to persistantXgcpEvents
table. The value of vismTrapIntIndex1 gives the value of
persistentXgcpEventNum. persistentXgcpEventName gives the
name associated with that event num. |
| TRAP-TYPE |
|
|
|
| persistentXgcpEventDeleted |
50787 |
| Indicates that an entry is deleted from persistantXgcpEvents
table. The value of vismTrapIntIndex1 gives the value of
persistantXgcpEventNum.
The varbind persistantXgcpEventName gives the name associated
with that event num. |
| TRAP-TYPE |
|
|
|
| mgDomainNameAdded |
50791 |
| Indicates that an entry is added to mgDomainNameTable. |
| TRAP-TYPE |
|
|
|
| mgDomainNameDeleted |
50789 |
| Indicates that an entry is deleted from mgDomainNameTable.
vismTrapIntIndex1 specifies the mgDomainNameIndex. |
| TRAP-TYPE |
|
|
|
| vismTonePlanAdded |
50798 |
| Indicates that an entry is added to vismTonePlanTable.
The value of vismTrapIntIndex1 gives the value of
tonePlanIndex. |
| TRAP-TYPE |
|
|
|
| vismTonePlanDeleted |
50799 |
| Indicates that an entry is deleted from vismTonePlanTable.
The value of vismTrapIntIndex1 gives the value of
tonePlanIndex. |
| TRAP-TYPE |
|
|
|
| vismRtpConnAdded |
50650 |
| Indicates that an entry has been added to vismRtpConnGrpTable
with vismRtpLcn.
The value of vismTrapIntIndex1 gives the vismRtpConnNum. |
| TRAP-TYPE |
|
|
|
| vismRtpConnDeleted |
50651 |
| Indicates that an entry with Lcn vismRtpLcn has been
deleted from vismRtpConnGrpTable. The value of
vismTrapIntIndex1 gives the vismRtpConnNum. |
| TRAP-TYPE |
|
|
|
| vismRtpConnStateChg |
50652 |
| Indicates that the alarm state of the entry in
vismRtpConnGrpTable with LCN vismRtpLcn changed.
The value of vismTrapIntIndex1 gives the vismRtpConnNum. |
| TRAP-TYPE |
|
|
|
| vismLapdTrStateIs |
50653 |
| Indicates that the LAPD Trunk state has changed to
'In Service'. The value of vismTrapIntIndex1 gives the
value of vismLapdTrunkNum. |
| TRAP-TYPE |
|
|
|
| vismLapdTrStateOos |
50654 |
| Indicates that the LAPD Trunk state has changed to
'Out Of Service'. The value of vismTrapIntIndex1 gives
the value of vismLapdTrunkNum. |
| TRAP-TYPE |
|
|
|
| vismLapdTrunkAdded |
50655 |
| Indicates that a new entry has been added to the
vismLapdTrunkGrpTable. The value of vismTrapIntIndex1
gives the value of vismLapdTrunkNum. |
| TRAP-TYPE |
|
|
|
| vismLapdTrunkDeleted |
50656 |
| Indicates that an existing entry has been deleted from
the vismLapdTrunkGrpTable. The value of vismTrapIntIndex1
gives the value of vismLapdTrunkNum. |
| TRAP-TYPE |
|
|
|
| mgcRedundancyGrpAdded |
50657 |
| Indicates that an entry has been added in the
mgcRedundancyGrptable.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum and vismTrapIntIndex2 gives the
value of mgcNumber. |
| TRAP-TYPE |
|
|
|
| mgcRedundancyGrpDeleted |
50658 |
| Indicates that an entry has been deleted from the
mgcRedudancyGrpTable.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum and vismTrapIntIndex2 gives the
value of mgcNumber. |
| TRAP-TYPE |
|
|
|
| mgcRedundancyGrpCommOk |
50659 |
| Triggered when the communication state of the
MGC redundancy group transitions to 'commOk' state.
The transition will be from 'commLoss' to 'commOk'
when communication between the gateway and the
call agent is established.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum. |
| TRAP-TYPE |
|
|
|
| mgcRedundancyGrpCommLoss |
50660 |
| Triggered when the communication state of the
MGC redundancy group transitions to 'commLoss'.
The transition will be from 'commOk' to 'commLoss'
when the callagent does not respond to gateway
initiated messages.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum. |
| TRAP-TYPE |
|
|
|
| mgcActiveInGrp |
50665 |
| Triggered when the MGC in an MGC Redundancy Group transitions
from inactive to active state. Indicates the active MGC in an
MGC Redundancy group.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum. The value of vismTrapIntIndex2 gives the
value of mgcNumber. |
| TRAP-TYPE |
|
|
|
| mgcInactiveInGrp |
50666 |
| Triggered when the MGC in an MGC Redundancy Group transitions
from active to inactive state.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum. The value of vismTrapIntIndex2 gives the
value of mgcNumber. |
| TRAP-TYPE |
|
|
|
| mgcRedundancyGrpProtocolAdded |
50661 |
| Indicates that an entry is added to the
mgcRedundancyGrpProtocolTable.
The value of vismTrapIntIndex1 gives the
value of mgcRedundancyGrpNum.
The value of vismTrapIntIndex2 gives the
value of mgProtocolNumber. |
| TRAP-TYPE |
|
|
|
| mgcRedundancyGrpProtocolDeleted |
50662 |
| Indicates that an entry is deleted from the
mgcRedundancyGrpProtocolTable.
The value of vismTrapIntIndex1 gives the
value of mgcRedundancyGrpNum.
The value of vismTrapIntIndex2 gives the
value of mgProtocolNumber. |
| TRAP-TYPE |
|
|
|
| peerGrpHeartbeatLost |
50663 |
| This notification indicates that the system failed to receive
a heartbeat from a specific peer group.
The notification is sent when srcpPeerGrpTimeSinceHeartbeat
crosses the srcpPeerGrpHeartbeatInterval threshold.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum. |
| TRAP-TYPE |
|
|
|
| peerGrpHeartbeatDetected |
50664 |
| This notification indicates that the system detected a
heartbeat from a specific peer group after it had been lost.
The notification is sent when srcpPeerGrpTimeSinceHeartbeat
which had exceeded the threshold, resets to 0 due to
receipt of a heartbeat. The value of vismTrapIntIndex1
gives the value of mgcRedundancyGrpNum. |
| TRAP-TYPE |
|
|
|
| mgcRedundancyGrpParamEntryAdded |
50668 |
| Indicates that an entry has been added in the
mgcRedundancyGrpParamTable.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum.
The entries in the mgcRedundancyGrpParamTable are
implicitly added when the first entry for that
mgcRedundancyGrpNum is added into the
mgcRedundancyGrpTable by the user. |
| TRAP-TYPE |
|
|
|
| mgcRedundancyGrpParamEntryDeleted |
50669 |
| Indicates that an entry has been deleted from the
mgcRedundancyGrpParamTable.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum.
The entries in the mgcRedundancyGrpParamTable are
implicitly deleted when the last entry for that
mgcRedundancyGrpNum is removed from the
mgcRedundancyGrpTable by the user. |
| TRAP-TYPE |
|
|
|
| srcpPeerGrpParamEntryAdded |
50670 |
| Indicates that an entry has been added to the
srcpPeerGrpParamTable.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum.
The entries in the srcpPeerGrpParamTable are
implicitly created when SRCP protocol is added for
the MGC Redundancy Group. |
| TRAP-TYPE |
|
|
|
| srcpPeerGrpParamEntryDeleted |
50671 |
| Indicates that an entry has been deleted from the
srcpPeerGrpParamTable.
The value of vismTrapIntIndex1 gives the value of
mgcRedundancyGrpNum.
The entries in the srcpPeerGrpParamTable are
implicitly deleted when the SRCP protocol configured
for the Mgc Redundancy Group is deleted. |
| TRAP-TYPE |
|
|
|
| cwAnnFileAddStarted |
50674 |
| Indicates that an attempt was made to add an
entry to the cwAnnounceTable.
This trap will not be generated at card reset
time when all of previously configured permanent
files are downloaded to bring the card up to date.
The value of vismTrapIntIndex1 gives the value
of cwAnnounceIndex. |
| TRAP-TYPE |
|
|
|
| cwAnnFileLoadComplete |
50675 |
| Indicates that an attempt to add an entry to the
cwAnnounceTable has been successfully completed.
The value of vismTrapIntIndex1 gives the value of
cwAnnounceIndex. |
| TRAP-TYPE |
|
|
|
| cwAnnFileLoadFailed |
50676 |
| Indicates that an attempt to add an entry to the
cwAnnounceTable has failed.
The value of vismTrapIntIndex1 gives the value of
cwAnnounceIndex. |
| TRAP-TYPE |
|
|
|
| cwAnnFileDeleted |
50677 |
| Indicates that an entry is deleted from
cwAnnounceTable.
The value of vismTrapIntIndex1 gives the value
of cwAnnounceIndex. |
| TRAP-TYPE |
|
|
|
| newFlow |
50672 |
| The newFlow trap indicates that the
originating system has installed a new flow in
its classifier, or (when reservation
authorization is in view) is prepared to
install such a flow in the classifier and is
requesting authorization. The objects included
with the notification may be used to read
further information using the Integrated
Services and RSVP MIBs. Authorization or non-
authorization may be enacted by a write to the
variable intSrvFlowStatus. |
| TRAP-TYPE |
|
|
|
| lostFlow |
50673 |
| The lostFlow trap indicates that the
originating system has removed a flow from its
classifier. |
| TRAP-TYPE |
|
|
|
| dspRASEndpointFailed |
50678 |
| Triggered by DSP channel failure associated
with an endpoint.
The value of vismTrapIntIndex1 gives the value
of mgEndpointNumber. |
| TRAP-TYPE |
|
|
|
| dspRASEndpointActive |
50679 |
| Triggered by DSP channel associated with an endpoint
after a channel failure corrected by the DSP.
The value of vismTrapIntIndex1 gives the value of
mgEndpointNumber. |
| TRAP-TYPE |
|
|
|
| vismConfigToneDetectAdded |
50683 |
| Indicates that an entry is added to
vismConfigToneDetectTable. The value of
vismTrapIntIndex1 gives the value of
vismConfigToneDetectNum. |
| TRAP-TYPE |
|
|
|
| vismConfigToneDetectDeleted |
50684 |
| Indicates that an entry is deleted from
vismConfigToneDetectTable. The value of
vismTrapIntIndex1 gives the value of
vismConfigToneDetectNum. |
| TRAP-TYPE |
|
|
|
| trapCidAdministrativeStateChange |
50784 |
| Indicates that the CID or bearer connection has
either changed state from CidInService to
CidCommandedOutOfService or vice versa. |
| TRAP-TYPE |
|
|
|
| vismCasTransTblAdded |
50685 |
| Indicates that an entry is added to the
cvcmABCDBitTemplateConfigTable.
vismTrapIntIndex1 will contain the
cvcmCasTemplateIndex and vismTrapIntIndex2
will contain the cvcmABCDPatternIndex.
cvcmCasTemplateName will indicate
the name of the CAS template added.
|
| TRAP-TYPE |
|
|
|
| vismCasTranTblDeleted |
50686 |
| Indicates that an entry is deleted from the
cvcmABCDBitTemplateConfigTable.
vismTrapIntIndex1 will contain the
cvcmCasTemplateIndex and vismTrapIntIndex2
will contain the cvcmABCDPatternIndex.
cvcmCasTemplateName will indicate
the name of the CAS template deleted.
|
| TRAP-TYPE |
|
|
|