CISCO-WAN-BBIF-ATM-CONN-MIB

File: CISCO-WAN-BBIF-ATM-CONN-MIB.mib (36252 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
BASIS-MIB CISCOWAN-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
MODULE-COMPLIANCE OBJECT-GROUP TEXTUAL-CONVENTION
DisplayString bbChanCnfGrp bbChanStateGrp
ciscoWan

Defined Types

IfNsapAddress  
ATM address used by the networking entity. The only address type presently supported is NSAP (20 octets)
TEXTUAL-CONVENTION    
  OCTET STRING Size(20)  

BbChanCnfGrpEntry  
SEQUENCE    
  bbChanCnfNum Integer32
  bbChanRowStatus INTEGER
  bbChanConnType INTEGER
  bbChanServiceType INTEGER
  bbChanConnDesc DisplayString
  bbChanSvcFlag INTEGER
  bbChanSvcConnId Integer32
  bbChanIfNum Integer32
  bbChanVpi Integer32
  bbChanVci Integer32
  bbChanUpcEnable INTEGER
  bbChanUpcPCR Integer32
  bbChanUpcCDVT Integer32
  bbChanUpcSCR Integer32
  bbChanUpcMBS Integer32
  bbChanGcra1Action INTEGER
  bbChanGcra2Action INTEGER
  bbChanUpcSCRPolicing INTEGER
  bbChanEfciThreshold Integer32
  bbChanDiscardOption INTEGER
  bbChanFrmDiscardThreshold Integer32
  bbChanClpHiThreshold Integer32
  bbChanClpLoThreshold Integer32
  bbChanCongstUpdateCode INTEGER
  bbChanMaxCellMemThreshold Integer32
  bbChanIngrPercentUtil Integer32
  bbChanEgrPercentUtil Integer32
  bbChanEgrSrvRate Integer32
  bbChanOvrSubOvrRide INTEGER
  bbChanLocalVpi Integer32
  bbChanLocalVci Integer32
  bbChanLocalNsapAddr IfNsapAddress
  bbChanRemoteVpi Integer32
  bbChanRemoteVci Integer32
  bbChanRemoteNsapAddr IfNsapAddress
  bbChanMaster INTEGER
  bbChanRtePriority Integer32
  bbChanMaxCost Integer32
  bbChanRestrictTrkType INTEGER
  bbChanTestType INTEGER
  bbChanTestState INTEGER
  bbChanTestResult Integer32
  bbChanTestTypeCPESide INTEGER
  bbChanTestStateCPESide INTEGER
  bbConnVpcFlag INTEGER
  bbConnServiceType INTEGER
  bbConnPCR Integer32
  bbConnSCR Integer32
  bbConnPercentUtil Integer32
  bbRemoteConnPCR Integer32
  bbRemoteConnSCR Integer32
  bbRemoteConnPercentUtil Integer32
  bbChanUpcMCR Integer32

BbChanStateGrpEntry  
SEQUENCE    
  bbChanStateNum Integer32
  bbChanState INTEGER
  bbChanEgrXmtState INTEGER
  bbChanIngrRcvState INTEGER

Defined Values

ciscoWanBbifAtmConnMIB 1.3.6.1.4.1.351.150.35
The MIB module to configure the ATM Connections on a broad band interface in PXM1 Service module.
MODULE-IDENTITY    

bbChanCnfGrpTable 1.3.6.1.4.1.351.110.5.2.7.1.1
The Broadband Channel config table is for a channel on logical interface. There will an entry for each of the channel added on the logical partition of the physical line. Following parameters are needed if the connection is from a PXM user port and policing is enabled. These apply to connection on PXM lines confiured as user port only. PCR/CDVT is used for GCRA1 and SCR/MBS is used for GCRA2 UpcEnable UpcPCR UpcCDVT UpcSCRPolicing for CBR conns. UpcPCR0 UpcCDVT0 for non CBR conns. UpcSCR UpcMBS
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BbChanCnfGrpEntry

bbChanCnfGrpEntry 1.3.6.1.4.1.351.110.5.2.7.1.1.1
The config table is for logical channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  BbChanCnfGrpEntry  

bbChanCnfNum 1.3.6.1.4.1.351.110.5.2.7.1.1.1.1
This identifies a channel on the PXM logical interface, used as PXM port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 16..4111  

bbChanRowStatus 1.3.6.1.4.1.351.110.5.2.7.1.1.1.2
This object is used for adding/deleting/modifying entries in the table. add(1) : Adds the entry. delete(2) : Deletes the entry modify(3) : Set this before modifying any entries in the table. Following parameters need to be available before creating the entry: bbChanConnType, bbChanServiceType.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER add(1), delete(2), modify(3)  

bbChanConnType 1.3.6.1.4.1.351.110.5.2.7.1.1.1.3
This specifies the connection type vpc(1) : Virtual Path Connection vcc(2) : Virtual Channel Connection This object can not be modified once the connection is created.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER vpc(1), vcc(2)  

bbChanServiceType 1.3.6.1.4.1.351.110.5.2.7.1.1.1.4
This specifies the service type cbr(1) : Constant Bit Rate vbr(2) : Variable Bit Rate abr(3) : Available Bit Rate ubr(4) : Unspecified Bit Rate vbr-rt(5): Variable Bit Rate - Real Time This object can not be modified once the connection is created.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER cbr(1), vbr(2), abr(3), ubr(4), vbr-rt(5)  

bbChanConnDesc 1.3.6.1.4.1.351.110.5.2.7.1.1.1.5
A string that has been defined to give a descriptive name to the connection.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

bbChanSvcFlag 1.3.6.1.4.1.351.110.5.2.7.1.1.1.6
This specifies the connection type svc(1) : SVC connection pvc(2) : PVC connection, used by PAR(Portable Auto Route) spvc(3) : Soft PVC connection, used by PNNI
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER svc(1), pvc(2), spvc(3)  

bbChanSvcConnId 1.3.6.1.4.1.351.110.5.2.7.1.1.1.7
This connection ID is for future use Currently not supported.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bbChanIfNum 1.3.6.1.4.1.351.110.5.2.7.1.1.1.8
Channel's logical Interface from which traffic of the connection will be received.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..32  

bbChanVpi 1.3.6.1.4.1.351.110.5.2.7.1.1.1.9
VPI for the connection.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4095  

bbChanVci 1.3.6.1.4.1.351.110.5.2.7.1.1.1.10
VCI for the connection.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..ffff  

bbChanUpcEnable 1.3.6.1.4.1.351.110.5.2.7.1.1.1.11
enables/disables UPC for Ingress cells.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

bbChanUpcPCR 1.3.6.1.4.1.351.110.5.2.7.1.1.1.12
PCR(0+1), Peak Cell Rate, specifies an upper bound on rate at which traffic can be submitted on an ATM connection. This object applies to the First Leaky Bucket for leaving cells with Cell Loss Priority of 0 or 1. . Units: cells per second. . Applicable connection types: UBR, CBR, VBR, ABR . Default: 50 . Ranges: T3 : 50-96000 E3 : 50-80000 OC3 : 50-353208 OC12: 50-1412832 PCR is used for GCRA1.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 50..1412832  

bbChanUpcCDVT 1.3.6.1.4.1.351.110.5.2.7.1.1.1.13
Compliant Cell Delay Variation. Also known as CDVT(0+1), Cell Delay Variation Tolerance, which specifies the maximum time period for accumulated violations of cell-arrival time parameters. This object applies to the First Leaky bucket for cells with Cell Loss Priority of 0 or 1. . Units: microseconds. . Applicable connection types: UBR, CBR, VBR, ABR . Default: CBR: 10000 Others: 250000
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..5000000  

bbChanUpcSCR 1.3.6.1.4.1.351.110.5.2.7.1.1.1.14
SCR, Sustainable Cell Rate, is an upper bound on the conforming average rate of an ATM connection, over time scales which are long relative to those for which the PCR is defined. Enforcement of this bound by the UPC could allow the network to allocate sufficient resources, but less than thos based on the PCR, and still ensure that the performance objectives (e.g., Cell Loss Ratio) can be achieved. . Units: cell per second. . Applicable connection types: . VBR, ABR . Ranges: T3 : 50-96000 E3 : 50-80000 OC3 : 50-353208 OC12: 50-1412832 . Default: 50
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..1412832  

bbChanUpcMBS 1.3.6.1.4.1.351.110.5.2.7.1.1.1.15
Maximum Burst Size (MBS). Also known as Compliant Burst Size (CBS). . Units: cells . Applicable connection types: . VBR, ABR . Default: 1000 . Range : 1-5000000
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..5000000  

bbChanGcra1Action 1.3.6.1.4.1.351.110.5.2.7.1.1.1.16
GCRA1 Action. 1 = No Action 2 = Tag Untagged cells 3 = Tag untagged cells and discard tagged cells 4 = Discard all (0+1) non-comforming cells.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), tagCells(2), tagAndDiscard(3), discardAllNonComformCells(4)  

bbChanGcra2Action 1.3.6.1.4.1.351.110.5.2.7.1.1.1.17
GCRA2 Action. 1 = No Action 2 = Tag Untagged cells 3 = Tag untagged cells and discard tagged cells 4 = Discard all (0+1) non-comforming cells.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), tagCells(2), tagAndDiscard(3), discardAllNonComformCells(4)  

bbChanUpcSCRPolicing 1.3.6.1.4.1.351.110.5.2.7.1.1.1.18
Selects SCR policing for CLP = 0 or all cells.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clp0(1), clp0and1(2), off(3)  

bbChanEfciThreshold 1.3.6.1.4.1.351.110.5.2.7.1.1.1.19
Threshold above which EFCI bit is to be set. Default Value is 3/4 of max cell count.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..491520  

bbChanDiscardOption 1.3.6.1.4.1.351.110.5.2.7.1.1.1.20
Enable Frame Discard or CLP Hysteresis.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clpHysteresis(1), frameDiscard(2)  

bbChanFrmDiscardThreshold 1.3.6.1.4.1.351.110.5.2.7.1.1.1.21
Ingress Frame Discard Threshold. Valid only when Ingress Frame Discard option is selected.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..491520  

bbChanClpHiThreshold 1.3.6.1.4.1.351.110.5.2.7.1.1.1.22
Ingress CLP High Threshold. Default is 3/4 of max cell count.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..491520  

bbChanClpLoThreshold 1.3.6.1.4.1.351.110.5.2.7.1.1.1.23
Ingress CLP Low Threshold. Valid only when Ingress CLP Hysteresis option is selected. Default Value is 1/2 of max cell count.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..491520  

bbChanCongstUpdateCode 1.3.6.1.4.1.351.110.5.2.7.1.1.1.24
Ingress Channel Congestion Update Code.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dontUpdate(1), setCiBit(2), setEfciBit(3), clearEfciBit(4)  

bbChanMaxCellMemThreshold 1.3.6.1.4.1.351.110.5.2.7.1.1.1.25
Maximum number of cells of that connection in the memory. Assuming Total Cell Memory is 512K cells, this is defaulted to half of total size.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..512000  

bbChanIngrPercentUtil 1.3.6.1.4.1.351.110.5.2.7.1.1.1.26
Percentage Utilization of the IngrService Rate. This is used for connection admission control.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

bbChanEgrPercentUtil 1.3.6.1.4.1.351.110.5.2.7.1.1.1.27
Percentage Utilization of the EgrService Rate. This is used for egress bandwidth calculation and connection admission control.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

bbChanEgrSrvRate 1.3.6.1.4.1.351.110.5.2.7.1.1.1.28
Egress service rate - This is used for egress bandwidth calculation and for connection admission control. The actual value depends on the speed of the logical interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..1412832  

bbChanOvrSubOvrRide 1.3.6.1.4.1.351.110.5.2.7.1.1.1.29
Channel Over Subscrive Override This MIB variable allows one to add a new connection on a port even if it is over subscribed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

bbChanLocalVpi 1.3.6.1.4.1.351.110.5.2.7.1.1.1.30
The VPI value for this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4095  

bbChanLocalVci 1.3.6.1.4.1.351.110.5.2.7.1.1.1.31
The VCI value for this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..ffff  

bbChanLocalNsapAddr 1.3.6.1.4.1.351.110.5.2.7.1.1.1.32
The Near End NSAP Address value for this channel.
Status: current Access: read-write
OBJECT-TYPE    
  IfNsapAddress  

bbChanRemoteVpi 1.3.6.1.4.1.351.110.5.2.7.1.1.1.33
The VPI value for this channel.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4095  

bbChanRemoteVci 1.3.6.1.4.1.351.110.5.2.7.1.1.1.34
The VCI value for this channel.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..ffff  

bbChanRemoteNsapAddr 1.3.6.1.4.1.351.110.5.2.7.1.1.1.35
The Far End NSAP Address value for this channel.
Status: current Access: read-write
OBJECT-TYPE    
  IfNsapAddress  

bbChanMaster 1.3.6.1.4.1.351.110.5.2.7.1.1.1.36
This is used by the PXM switch platform module, to determine if this endpoint ia master or slave.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER master(1), slave(2), unknown(3)  

bbChanRtePriority 1.3.6.1.4.1.351.110.5.2.7.1.1.1.37
This is also known as class of service, it is used by PXM to determine how important this connection is when selecting connections to route.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..15  

bbChanMaxCost 1.3.6.1.4.1.351.110.5.2.7.1.1.1.38
Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

bbChanRestrictTrkType 1.3.6.1.4.1.351.110.5.2.7.1.1.1.39
Restricted trunk type for routind, used by PXM. It specifies that the connection either cannot be routed over satellite trunks or terrestrial trunks, or it can be on any type of trunk.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noRestriction(1), terrestrialTrunk(2), satelliteTrunk(3)  

bbChanTestType 1.3.6.1.4.1.351.110.5.2.7.1.1.1.40
The chanTestType starts testing the continuity or delay of a connection. It sends specific cell patterns toward the network and the terminating end of this connection has to be an AXIS or ASI of a BPX in order for this test to be working. The receiving node would loop back when it receives these cells. The test should be done in about couple of seconds. testcon(1) : The testcon tests the continuity of the connection and testdelay uses the same test except that it measures for delay through the network. To test the delay follow this procedure: a- set chanTestType to testdelay b- read chanTestState till it is Pass or Fail c- Read chanTestResult for the delay if it is Pass * Note that the chanTestType would go back to notest when the test is completed To test the continuity follow this procedure: a- set chanTestType to testcon b- read chanTestState till it is Pass or Fail * Note that the chanTestType would go back to notest when the test is completed You CAN NOT select 2 tests back to back, you have to select one and wait for the result and then start the other one.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER testcon(1), testdelay(2), notest(3)  

bbChanTestState 1.3.6.1.4.1.351.110.5.2.7.1.1.1.41
This object provides the state of the test performed on a connection. When you add a connection then the chanTestState becomes notinprogress and when you select any test, it would go to inprogress state and after it completes the test, it will go to failed or passed state. 1 = Passed 2 = Failed 3 = In Progress 4 = Not In Progress
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER passed(1), failed(2), inprogress(3), notinprogress(4)  

bbChanTestResult 1.3.6.1.4.1.351.110.5.2.7.1.1.1.42
This is round trip delay in milliseconds. When you select testdelay option for the chanTestType, the result of the test that is measured in milliseconds can be read in chanTestResult.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

bbChanTestTypeCPESide 1.3.6.1.4.1.351.110.5.2.7.1.1.1.43
The chanTestType starts testing the segment continuity of a connection. It sends OAM Segment loopback cell towards port side (CPE) The CPE would loop back the cell To test the continuity follow this procedure: a- set chanTestTypeCPEside to testconseg b- read chanTestState till it is Pass or Fail *Note that the chanTestType would go back to notest when the test is completed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER testconseg(1), notest(2)  

bbChanTestStateCPESide 1.3.6.1.4.1.351.110.5.2.7.1.1.1.44
This shows the state of the test When you add a connection then the chanTestState becomes notinprogress and when you select any test, it would go to inprogress state and after it completes the test, it will go to failed or passed state. 1 = Passed 2 = Failed 3 = In Progress 4 = Not In Progress
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER passed(1), failed(2), inprogress(3), notinprogress(4)  

bbConnVpcFlag 1.3.6.1.4.1.351.110.5.2.7.1.1.1.45
This represents the connection type, used for PXM to identify VPC/VCC.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER vpc(1), vcc(2)  

bbConnServiceType 1.3.6.1.4.1.351.110.5.2.7.1.1.1.46
This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 4 ==> Unspecified Bit Rate 6 ==> Available Bit Rate ( standard ) 8 ==> Variable Bit Rate - Real-Time Note that this is used by PXM card, Also to make it compatible with existing AUSM MIB definition, value 3 is not used. foresight ABR is not supported in PXM , i.e Virtual Service Module
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER cbr(1), vbr(2), ubr(4), abrstd(6), vbrrt(8)  

bbConnPCR 1.3.6.1.4.1.351.110.5.2.7.1.1.1.47
Peak cell rate, could be derived from the end point parameter
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bbConnSCR 1.3.6.1.4.1.351.110.5.2.7.1.1.1.48
Sustained cell rate, could be derived from the end point parameter
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bbConnPercentUtil 1.3.6.1.4.1.351.110.5.2.7.1.1.1.49
This is the expected long-term utilization of the channel by this end-point.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

bbRemoteConnPCR 1.3.6.1.4.1.351.110.5.2.7.1.1.1.50
Peak cell rate of the other end, if not set, will be set to the same as local end PCR (bbChanUpcPCR). However, note that if the PCRs for both local and remote end are set to the different value (i.e., asymmetric conn), then this should be set differently from local end PCR.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bbRemoteConnSCR 1.3.6.1.4.1.351.110.5.2.7.1.1.1.51
Sustained cell rate of the other end, if not set, will be set to the same as local end SCR (bbChanUpcSCR). However, note that if the PCRs for both local and remote end are set to the different value (i.e., asymmetric conn), then this should be set differently from local end SCR.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bbRemoteConnPercentUtil 1.3.6.1.4.1.351.110.5.2.7.1.1.1.52
This is the expected long-term utilization of the channel by this end-point. If this is not specified in the connection setup request, it'll be defaulted to 100 percent
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

bbChanUpcMCR 1.3.6.1.4.1.351.110.5.2.7.1.1.1.53
SCR, Sustainable Cell Rate, is an upper bound on the conforming average rate of an ATM connection, over time scales which are long relative to those for which the PCR is defined. Enforcement of this bound by the UPC could allow the network to allocate sufficient resources, but less than thos based on the PCR, and still ensure that the performance objectives (e.g., Cell Loss Ratio) can be achieved. . Units: cell per second. . Applicable connection types: . ABR . Ranges: T3 : 50-96000 E3 : 50-80000 OC3 : 50-353208 OC12: 50-1412832 . Default: 50
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..1412832  

bbChanNumNextAvailable 1.3.6.1.4.1.351.110.5.2.7.1.2
This variable contains the next unused channel number of the possible 4096 . This number can be used in channel config table. ChanNumNextAvailable gets updated whenever this number is used to create a new logical channel. Value 0 for this variable indicates that no more channels are available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 16..4111  

bbChanVpIdNextAvailable 1.3.6.1.4.1.351.110.5.2.7.1.3
This in only valid for a Service Module, will NOT be used in PXM. This variable contains the next unused local VPId of the possible 1 to 4095. This number can be used in channel config table. It gets updated if the number is used to create a new vp connection. The max. no. of VP conn.s is limited to the VPI range configured for this logical interface. Value of 0 for this variable indicates that no more vp connections are available
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..4095  

bbChanStateGrpTable 1.3.6.1.4.1.351.110.5.2.7.2.1
The Broadband Channel state table is for a channel on logical interface. There will an entry for each of the channel added on the logical partition of the physical line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BbChanStateGrpEntry

bbChanStateGrpEntry 1.3.6.1.4.1.351.110.5.2.7.2.1.1
The state table is for logical channel. The available number of channels on the broadband interface (user ports) on the PXM card is restricted to 4K. The PXM card has 2 Queue Engines ( QE0 and QE1). Current calculations allow 31954 GLCNs on QE0, and 31748 GLCNs on QE1.
Status: current Access: not-accessible
OBJECT-TYPE    
  BbChanStateGrpEntry  

bbChanStateNum 1.3.6.1.4.1.351.110.5.2.7.2.1.1.1
Refers to the logical channel number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 16..4111  

bbChanState 1.3.6.1.4.1.351.110.5.2.7.2.1.1.2
This variable indicates the state of the VC (channel).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notconfigured(1), normal(2), alarm(3)  

bbChanEgrXmtState 1.3.6.1.4.1.351.110.5.2.7.2.1.1.3
Indicates the status of port transmit(Egress).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), normal(2), sendingAis(3), sendingFerf(4)  

bbChanIngrRcvState 1.3.6.1.4.1.351.110.5.2.7.2.1.1.4
indicates the status of port receive(Ingress).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), normal(2), receivingAis(3), receivingFerf(4), alarm(5)  

cwbAtmConnMIBConformance 1.3.6.1.4.1.351.150.35.2
OBJECT IDENTIFIER    

cwbAtmConnMIBGroups 1.3.6.1.4.1.351.150.35.2.1
OBJECT IDENTIFIER    

cwbAtmConnMIBCompliances 1.3.6.1.4.1.351.150.35.2.2
OBJECT IDENTIFIER    

cwbAtmConnCompliance 1.3.6.1.4.1.351.150.35.2.2.1
The compliance statement for SNMP entities which support Frame realy connection MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

cwbAtmConnGroup 1.3.6.1.4.1.351.150.35.2.1.1
A collection of objects providing information applicable to an ATM Connection on broad band interfaces.
Status: current Access: read-only
OBJECT-GROUP    

cwbAtmConnStateGroup 1.3.6.1.4.1.351.150.35.2.1.2
A collection of objects related to state of ATM Connections on Broad band interface.
Status: current Access: read-only
OBJECT-GROUP    

cwbAtmConnGeneralGroup 1.3.6.1.4.1.351.150.35.2.1.3
A collection of objects related to next available channeli number and next available VPI value of connections supported.
Status: current Access: read-only
OBJECT-GROUP