CISCO-WAN-SRCP-MIB

File: CISCO-WAN-SRCP-MIB.mib (29249 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
CISCOWAN-SMI CISCO-WAN-MGC-REDUN-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
Counter32 IpAddress DisplayString
MODULE-COMPLIANCE OBJECT-GROUP ciscoWan
mgcRedundancyGrpNum

Defined Types

SrcpPeerEntry  
SEQUENCE    
  srcpPeerId Integer32
  srcpPeerName DisplayString
  srcpPeerPortNumber Integer32
  srcpPeerHeartbeatInterval Integer32
  srcpPeerTimeSinceHeartbeat Integer32
  srcpPeerMaxPduSize Integer32

SrcpPeerGrpParamEntry  
SEQUENCE    
  srcpPeerGrpHeartbeatInterval Integer32
  srcpPeerGrpTimeSinceHeartbeat Integer32
  srcpPeerGrpMaxPduSize Integer32

SrcpPeerStatsEntry  
SEQUENCE    
  srcpStatsPeerIpAddress IpAddress
  srcpStatsPeerName DisplayString
  packetsDiscardedCnts Counter32
  augwCnts Counter32
  augwFailCnts Counter32
  aulnCnts Counter32
  aulnFailCnts Counter32
  ntfyCnts Counter32
  ntfyFailCnts Counter32
  rqntCnts Counter32
  rqntFailCnts Counter32

Defined Values

ciscoWanSrcpMIB 1.3.6.1.4.1.351.150.11
The MIB module for managing SRCP(Simple Resource Coordination Protocol) implementations. SRCP is a resource coordination protocol used between a MGC(Media Gateway Controller) and a MG(Media Gateway). SRCP MIB is applicable to both controllers (SRCP clients) and gateways (SRCP servers). MGMIB: This is the short name used for CISCO-WAN-MG-MIB in this MIB.
MODULE-IDENTITY    

srcpObjects 1.3.6.1.4.1.351.150.11.1
OBJECT IDENTIFIER    

srcpAdminObjects 1.3.6.1.4.1.351.150.11.1.1
OBJECT IDENTIFIER    

srcpStatsObjects 1.3.6.1.4.1.351.150.11.1.2
OBJECT IDENTIFIER    

srcpAdminRetyObjects 1.3.6.1.4.1.351.150.11.1.3
OBJECT IDENTIFIER    

srcpVersion 1.3.6.1.4.1.351.150.11.1.1.1
The name of the SRCP protocol version for exmaple SRCP 1.0.2. If MGMIB is supported, this name corresponds to mgProtocolName (defined in CISCO-WAN-MG-MIB MIB) in an entry to mgSupportedProtocolTable.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..64)  

srcpPortNumber 1.3.6.1.4.1.351.150.11.1.1.2
This object is used to configure the UDP port used for SRCP on the system (local UDP port). It is configurable only if the system is in a locked or disabled state (i.e If MGMIB Is supported, mgAdministrativeState(defined in CISCO-WAN-MG-MIB MIB) should be 'locked' before the UDP port can be configured).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1025..65535  

srcpPeerTable 1.3.6.1.4.1.351.150.11.1.1.3
This is a table which is used to provision peer-specific SRCP configuration and administration information. Each table entry corresponds to an SRCP peer as identified by its domain name(srcpPeerName).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SrcpPeerEntry

srcpPeerEntry 1.3.6.1.4.1.351.150.11.1.1.3.1
Represents an individual table entry in srcpPeerTable. Each row corresponds to an SRCP peer and is identified by its domain name (srcpPeerName). Entries in this table are implicitly created by the agent. If the agent supports MGMIB, this occurs as follows: An entry shall be created when an entry is created in the mgcRedundancyGrpProtocolTable(defined in CISCO-WAN-MGC-REDUN-MIB MIB) and when mgProtocolNumber (defined in CISCO-WAN-MG-MIB MIB) refers to SRCP as supported protocol. An entry will be made for all MGC(Media Gateway Controller) in that MGC Redundancy Group. Accordingly, an entry shall be deleted if the corresponding entry in the mgcRedundancyGrpProtocolTable is deleted. If the agent does not support MGMIB, entry creation might occur when the first SRCP communication with an IP address/domain name occurs. if MGC Redundacy feature is supported the following objects: srcpPeerHeartbeatInterval, srcpPeerTimeSinceHeartbeat rcpPeerMaxPduSize are not meaningful here. These objects are defined per MGC Redundancy Group rather than per MGC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SrcpPeerEntry  

srcpPeerId 1.3.6.1.4.1.351.150.11.1.1.3.1.1
This object identifies the SRCP peer and serves as index to this table. If MGMIB is supported, this is the same as the mgcNumber(defined in CISCO-WAN-MG-MIB MIB) from the mgcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

srcpPeerName 1.3.6.1.4.1.351.150.11.1.1.3.1.2
This object identifies the name of the SRCP peer. If MGMIB is supported, this is the same as the mgcName from the mgcTable.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..64)  

srcpPeerPortNumber 1.3.6.1.4.1.351.150.11.1.1.3.1.3
This object is used to configure the UDP port of the SRCP peer.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1025..65535  

srcpPeerHeartbeatInterval 1.3.6.1.4.1.351.150.11.1.1.3.1.4
This object is used to configure the length of the heartbeat interval, in milliseconds. The heartbeat interval indicate when the GW(Gateway) is expected to receive a heartbeat from a specific peer or MGC group. If value is 0, heartbeat for this peer is not monitored. The heartbeat interval less than 100 is not allowed (except 0). If MGC Redundancy is supported, this object is not effective. Instead, the user should use srcpPeerGrpHeartbeatInterval.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

srcpPeerTimeSinceHeartbeat 1.3.6.1.4.1.351.150.11.1.1.3.1.5
The time since the last heartbeat was received, in milliseconds. This represents the difference between the current time and the last time an SRCP command was received. A value of 0 shall be returned if the heartbeat is not monitored. Even if the heartbeat is monitored, a value of 0 shall be returned if any of the following is true: i) The system is locked or disabled (as indicated by mgAdministrativeState). ii) The srcpPeer is unassociated as indicated by mgcAssociationState(defined in CISCO-WAN-MG-MIB MIB). If MGC Redundancy is supported, this object is not effective. Instead, the user should use srcpPeerGrpTimeSinceHeartbeat.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

srcpPeerMaxPduSize 1.3.6.1.4.1.351.150.11.1.1.3.1.6
This object is used to configure the maximum UDP PDU(Protocol Data Unit) size, in octets, that may be used for SRCP communications with the peer. This value may not be configurable for all agents. If MGC Redundancy is supported, this object is not effective. Instead, the user should use srcpPeerGrpMaxPduSize.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32 4095..65535  

srcpPeerGrpParamTable 1.3.6.1.4.1.351.150.11.1.1.4
This table is used to provision SRCP parameters for an MGC Redundancy group. MGCs can be configured as part of MGC Redundancy groups. This feature allows for redundant call agents. Each table entry corresponds to an SRCP peer entry that is identified by the MGC Redundancy group number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SrcpPeerGrpParamEntry

srcpPeerGrpParamEntry 1.3.6.1.4.1.351.150.11.1.1.4.1
Represents an individual table entry in the srcpPeerGrpParamTable. Each row corresponds to an MGC Redundancy Group and is identified by the MGC Redundancy Group Number. Entries are implicitly created when the SRCP protocol is added for an MGC Redundancy Group. The entry will be removed if the SRCP protocol is removed for an MGC Redundancy Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SrcpPeerGrpParamEntry  

srcpPeerGrpHeartbeatInterval 1.3.6.1.4.1.351.150.11.1.1.4.1.1
This object is used to configure the length of the heartbeat interval, in milliseconds. If 0, heartbeat for this peer Group is not monitored. The heartbeat interval less than 100 is not allowed (except 0).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

srcpPeerGrpTimeSinceHeartbeat 1.3.6.1.4.1.351.150.11.1.1.4.1.2
The time since the last heartbeat was received, in milliseconds. This represents the difference between the current time and the last time an SRCP command was received. A value of 0 shall be returned if the heartbeat is not monitored. Even if the heartbeat is monitored, a value of 0 shall be returned if any of the following is true: i) The system is locked or disabled (as indicated by mgAdministrativeState). ii) The stateChangeNtfy flag is disabled for the srcpPeer Group (as indicated by mgcRedundancyGrpStateChangeNtfy of CISCO-WAN-MGC-REDUN-MIB).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

srcpPeerGrpMaxPduSize 1.3.6.1.4.1.351.150.11.1.1.4.1.3
This object is used to configure the maximum UDP PDU size, in octets, that may be used for SRCP communications with the peer. This value may not be configurable for all agents.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4095..65535  

srcpRequestTimeOut 1.3.6.1.4.1.351.150.11.1.3.1
This object specifies the minimum timeout value. This value along with srcpRequestMaxTimeout and srcpRequestRetries is used to determine the exponential retry interval for retransmitting unacknowledged SRCP messages. It is the responsibility of the requesting entity to provide suitable timeouts for all outstanding commands, and to retry commands when timeouts exceeded. The default value of this object is 500 milliseconds. When the value of this object changes srcpAdminObjects group changed trap will be sent as specify by vismConfigChangeTypeBitMap in CISCO-VISM-MODULE-MIB.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10000  

srcpRequestRetries 1.3.6.1.4.1.351.150.11.1.3.2
This object specifies the number of retries for a SRCP request that exceeds timeout. It is the responsibility of the requesting entity to provide suitable timeouts for all outstanding commands, and to retry when times out. The default value of this object is 3. When the value of this object changes srcpAdminObjects group changed trap will be sent as specify by vismConfigChangeTypeBitMap in CISCO-VISM-MODULE-MIB.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10  

srcpRequestMaxTimeout 1.3.6.1.4.1.351.150.11.1.3.3
This object specifies the maximum timeout value. This timer value is used along with srcpRequestTimeOut and srcpRequestRetries to determine the exponential retry interval for retransmitting unacknowledged SRCP messages. The value of this timer has to be greater than or equal to srcpRequestTimeOut. The default value of this object is 500 milliseconds. When the value of this object changes srcpAdminObjects group changed trap will be sent as specify by vismConfigChangeTypeBitMap in CISCO-VISM-MODULE-MIB.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10000  

srcpPeerStatsTable 1.3.6.1.4.1.351.150.11.1.2.1
This table contains SRCP statistics information since reset. SRCP statistics are kept in this table, with each table entry containing the statistics of SRCP messages that communicated with a peer at a specific IP address of the peer. It differs from the SRCP peer table which maintains information on a per call agent basis as identified by their domain names.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SrcpPeerStatsEntry

srcpPeerStatsEntry 1.3.6.1.4.1.351.150.11.1.2.1.1
The row of the srcpPeerStatsTable contains information about SRCP message statistics per IP address of the MGC. An entry is implicitly created and deleted by the agent. There can be two cases: 1. Case of Internal address resolution : In this case IP addresses of all SRCP peers are resolved internally. If the agent supports the MGMIB, the following referential integrity rules apply: When an entry is added to mgcResolutionTable defined in CISCO-WAN-MG-MIB with a specific IP address, an entry is created in this srcpPeerStatsTable for that IP address. When an entry is deleted from mgcResolutionTable, the row with the corresponding IP address in this table will be deleted. 2. Case of External address resolution : If there is at least one Call agent whose IP address is resolved externally, an entry is created whenever SRCP communication occurs with a new IP address. Table entries are never deleted, but must be nonpersistent in agent implementations, i.e. must be purged in case of a system shutdown/restart.
Status: current Access: not-accessible
OBJECT-TYPE    
  SrcpPeerStatsEntry  

srcpStatsPeerIpAddress 1.3.6.1.4.1.351.150.11.1.2.1.1.1
This object specifies the IP address of the SRCP peer and serves as index to the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

srcpStatsPeerName 1.3.6.1.4.1.351.150.11.1.2.1.1.2
Denotes the name of the SRCP peer. This is the same as the mgcName from the mgcTable. It is provided here as a read-only parameter as a convinience feature.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..64)  

packetsDiscardedCnts 1.3.6.1.4.1.351.150.11.1.2.1.1.3
The number of packets that were received and discarded. The packets may get discarded because of indecipherable PDUs like bad protocol version, bad command verb etc, or because of unknown transaction IDs (in case of SRCP clients).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

augwCnts 1.3.6.1.4.1.351.150.11.1.2.1.1.4
The total number of AUGW(Audit Gateway) commands received from the peer on this IP address.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

aulnCnts 1.3.6.1.4.1.351.150.11.1.2.1.1.5
The total number of AULN(Audit Line) commands received from or sent to the peer on this IP address.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rqntCnts 1.3.6.1.4.1.351.150.11.1.2.1.1.6
The total number of RQNT(Notification Request) commands received from or sent to the peer on this IP address.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ntfyCnts 1.3.6.1.4.1.351.150.11.1.2.1.1.7
The total number of NTFY(Notify) commands received from or sent to the peer on this IP address.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

augwFailCnts 1.3.6.1.4.1.351.150.11.1.2.1.1.8
For MG : The total number of AUGW commands received that were responded to with a failure return code. For MGC : The total number of AUGW commands sent which were timed out without a response or for which a response with failure return code was received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

aulnFailCnts 1.3.6.1.4.1.351.150.11.1.2.1.1.9
Media gateway : The total number of AULN commands received that were responded to with a failure return code. Media gateway controller : The total number of AULN commands sent which were timed out without a response or For which a response with failure return code was received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rqntFailCnts 1.3.6.1.4.1.351.150.11.1.2.1.1.10
Media gateway : The total number of RQNT commands received that were responded to with a failure return code. Media gateway controller : The total number of RQNT commands sent which were timed out without a response or for which a response with failure return code was received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ntfyFailCnts 1.3.6.1.4.1.351.150.11.1.2.1.1.11
Media gateway : The total number of NTFY commands sent which were timed out without a response or for which a response with failure return code was received. Media gateway controller: The total number of NTFY commands received that were responded to with a failure return code.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

srcpMIBConformance 1.3.6.1.4.1.351.150.11.3
OBJECT IDENTIFIER    

srcpMIBCompliances 1.3.6.1.4.1.351.150.11.3.1
OBJECT IDENTIFIER    

srcpMIBGroups 1.3.6.1.4.1.351.150.11.3.2
OBJECT IDENTIFIER    

srcpMIBCompliance 1.3.6.1.4.1.351.150.11.3.1.1
The compliance statement for the SNMPv2 entities which implement SRCP MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

srcpMIBComplaince2 1.3.6.1.4.1.351.150.11.3.1.2
The compliance statement for the SNMPv2 entities which implement SRCP MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

srcpMIBComplaince3 1.3.6.1.4.1.351.150.11.3.1.3
The compliance statement for the SNMPv2 entities which implement SRCP MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

srcpConfigurationGroup 1.3.6.1.4.1.351.150.11.3.2.1
This group contains objects related to configuration of SRCP. Min Access of read only is permissible for system providing only a fixed SRCP port.
Status: deprecated Access: read-only
OBJECT-GROUP    

srcpStatisticsGroup 1.3.6.1.4.1.351.150.11.3.2.2
This group contains the statistics per SRCP peer.
Status: deprecated Access: read-only
OBJECT-GROUP    

srcpConfigurationGroup2 1.3.6.1.4.1.351.150.11.3.2.3
This group contains objects related to configuration of SRCP. Min Access of read only is permissible for system providing only a fixed SRCP port.
Status: deprecated Access: read-only
OBJECT-GROUP    

srcpConfigurationGroup3 1.3.6.1.4.1.351.150.11.3.2.5
This group contains objects related to configuration of SRCP. Min Access of read only is permissible for system providing only a fixed SRCP port.
Status: current Access: read-only
OBJECT-GROUP    

srcpStatisticsGroup2 1.3.6.1.4.1.351.150.11.3.2.4
This group contains the statistics per SRCP peer.
Status: current Access: read-only
OBJECT-GROUP