CISCO-WAN-SRM-BERT-MIB

File: CISCO-WAN-SRM-BERT-MIB.mib (31432 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
BASIS-MIB CISCOWAN-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
MODULE-COMPLIANCE OBJECT-GROUP DisplayString
axisDiagnostics ciscoWan

Defined Types

BertDDSSeekResultsTableEntry  
SEQUENCE    
  bertDDSSeekResultsTableIndex Integer32
  bertDDSCode INTEGER

BertSupportedTestsTableEntry  
SEQUENCE    
  bertSupportedTestsTableIndex Integer32
  bertSupportFlag INTEGER
  bertTestMediumMask Integer32
  bertModeMask Integer32
  bertDeviceToLoopMask Integer32
  bertPatternMask Integer32
  bertLoopbackMask Integer32
  bertCardT1E1Type INTEGER

Defined Values

ciscoWanSrmBertMIB 1.3.6.1.4.1.351.150.31
The MIB Module for BERT(Bit Error Rate Testing) using Service Resource Module(SRM). This MIB module is used for BERT on FRSM, AUSM, CESM, VISM modules. This module contains information on results from BERT tests using DDS(Digital Data Service) pattern.
MODULE-IDENTITY    

bert 1.3.6.1.4.1.351.110.6.1
OBJECT IDENTIFIER    

bertControl 1.3.6.1.4.1.351.110.6.1.1
This object controls all the SET operations on this MIB group. acquireBert : Acquire BERT resources. cnfBert : Configure the required BERT test. startBert : The configured test has to be started. modBert : Modify parameters for the ongoing BERT test. delBert : Running BERT test has to be stopped. The above list shows the sequence in which the SET operations on this group need to be done, ideally. Bert can be operated upon only with bertUserId and bertSlotNumber. The default value is 0, means no action.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER acquireBert(1), releaseBert(2), cnfBert(3), startBert(4), modBert(5), delBert(6)  

bertResourceStatus 1.3.6.1.4.1.351.110.6.1.2
All of bert resources can be used by only one user at a time. This gives the status of the resources.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER free(1), inUse(2), cleanupPending(3)  

bertOwner 1.3.6.1.4.1.351.110.6.1.3
This refers to the user who owns the BERT resources. If the user is a CLI user, then this is username. If it is SNMP Manager(For example Cisco Wan Manager), then this would be the IP address. For example, this value can be, 192.9.209.157 within quotes.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bertUserId 1.3.6.1.4.1.351.110.6.1.4
This identifies the user who wants to do a SET operation on this group. This will be compared against bertOwner and access will be given only if it matches. Hence, for every SET request, this object should have a valid value. If the user is a CLI user, then this is username. If it is SNMP Manager, then this would be the IP address. For example, this value can be, 192.9.209.157 within quotes. Required for bert operations.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

bertStatus 1.3.6.1.4.1.351.110.6.1.5
This variable provides the status of BERT in the shelf.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), bertInSync(2), bertOutOfSync(3), searchingDDSCommands(4), farEndInLoop(5), facilityInLoop(6), portFacilityFifoFault(7), portFacilityFifoOutOfSync(8), metallicInLoop(9), bertFailed(10)  

bertSlotNumber 1.3.6.1.4.1.351.110.6.1.6
specifies the physical slot number of the Service Module which is to run BERT For MGX 8220, the range is 5-14. For MGX 8850, the range is 1-6, 9-14, 17-22, 25-30. Required for bert operations.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..30  

bertTestMedium 1.3.6.1.4.1.351.110.6.1.7
specifies whether the bert is to test a port or an entire T1/E1 line. No default value for this, it has to be set if bert is configured.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER port(1), line(2)  

bertPort 1.3.6.1.4.1.351.110.6.1.8
specifies the port number for BERT.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bertLine 1.3.6.1.4.1.351.110.6.1.9
specifies the line number for BERT. If the test medium is port, this represents the line to which the port belongs.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bertMode 1.3.6.1.4.1.351.110.6.1.10
specifies the mode, the BERT module is to be configured for.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER bertPatternTest(1), ddsSeek(2), loopback(3)  

bertDeviceToLoop 1.3.6.1.4.1.351.110.6.1.11
This shows the type of the end device and the type of the loopback used (latching/nonlatching/polynomial).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noLatchOCUwith1(1), noLatchOCUwitout1(2), noLatchCSU(3), noLatchDSU(4), latchDS0Drop(5), latchDS0Line(6), latchOCU(7), latchCSU(8), latchDSU(9), latchHL96(10), v54Polynomial(11), inband(12), esf(13), metallic(14), noDevice(15), smartJackInband(16)  

bertDS0DPIterationCount 1.3.6.1.4.1.351.110.6.1.12
The Iteration Register needs to be programmed in SRM when DSO drop loop option is selected in bertDeviceToLoop. The value to be programmed there is minus one of this object value, since the register is 0 based. DSP-OP devices can be cross connected in the centeral office. By this, the user has capablitiy to put any of the devices in the chain in loopback mode. This is done by repeating the latching activation code in a specific manner. The binary number in the iterataion register determines how many times the first portion of a latching loop activation code needs to be repeated as per user request and according to the Bellcore spec. A value of 0 results in no iteration and will cause the very first device in chain to go into loop back. A value of 1 will result into one iteration and will cause the second device to go into loopback and so on. The range of this count is 1 to 32, and it would translate to a range of 0 to 31 for the iteration register.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..32  

bertPattern 1.3.6.1.4.1.351.110.6.1.13
This variable determines BERT pattern to be transmitted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allZeros(1), allOnes(2), alternateONeZero(3), doubleOneZero(4), fifteenBit(5), twentyBit(6), twentyBitQRSS(7), twentythreeBit(8), oneInEight(9), threeIntwentyfour(10), dds-1(11), dds-2(12), dds-3(13), dds-4(14), dds-5(15), nineBit(16), elevenBit(17)  

bertLoopback 1.3.6.1.4.1.351.110.6.1.14
specifies the type of loopback to be (d)established.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER farEndLoopback(1), facilityLoopback(2), metallicLoopback(3)  

bertLoopbackOperation 1.3.6.1.4.1.351.110.6.1.15
specifies the operation of loopback (up or down).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER loopUp(1), loopDown(2)  

bertDS0Speed 1.3.6.1.4.1.351.110.6.1.16
represents the ds0 speed of the test running.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER speed56k(1), speed64k(2)  

bertTimeSlots 1.3.6.1.4.1.351.110.6.1.17
represents the number of ds0s in the test medium chosen.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bertStartTime 1.3.6.1.4.1.351.110.6.1.18
The syntax is hh:mm:ss The time zone is as configured in the shelf.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(8)  

bertStartDate 1.3.6.1.4.1.351.110.6.1.19
On MGX 8220, the syntax is mm/dd/yy On MGX 8850, the syntax is mm/dd/yyyy.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(10)  

bertBitCount 1.3.6.1.4.1.351.110.6.1.20
This shows the number of bits transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bertBitErrorCount 1.3.6.1.4.1.351.110.6.1.21
This shows the number of bits received in error.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bertErrorInjectCount 1.3.6.1.4.1.351.110.6.1.22
This shows the number of times error was injected.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bertCleanupAction 1.3.6.1.4.1.351.110.6.1.23
When the BERT has to be stopped or aborted (due to card state changes), this object would give the exact action to take. The bert related changes to the shelf, then, can be cleaned up. When its value is a Loopdown, it implies smCleanup plus the corresponding Loopdown.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noAction(1), smCleanup(2), latchDS0DropLoopdown(3), latchDS0LineLoopdown(4), latchOCULoopdown(5), latchCSULoopdown(6), latchDSULoopdown(7), latchHL96Loopdown(8), v54PolynomialLoopdown(9), inbandLoopdown(10), esfLoopdown(11), facilityLoopdown(12), metallicLoopdown(13), smartJackInbandLoopdown(14)  

bertAbortReason 1.3.6.1.4.1.351.110.6.1.24
when the BERT is aborted, this object would give the reason for that.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ascStateChange(1), smStateChange(2), srmStateChange(3), coreCardSwitch(4), smRedundancySwitch(5)  

bertDDSSeekResultsTableFirstIndex 1.3.6.1.4.1.351.110.6.1.25
Denotes the index of the oldest entry in the table. A value of zero means that there are no entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..20  

bertDDSSeekResultsTableLastIndex 1.3.6.1.4.1.351.110.6.1.26
Denotes the index of the latest entry in the table. A value of zero means that there are no entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..20  

bertDDSSeekResultsTable 1.3.6.1.4.1.351.110.6.1.27
This table contains all available DDS patterns detected and latched by an interaface(lines,ports etc) configured to detect DDS patterns.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BertDDSSeekResultsTableEntry

bertDDSSeekResultsTableEntry 1.3.6.1.4.1.351.110.6.1.27.1
An entry in the detected DDS codes table.
Status: current Access: not-accessible
OBJECT-TYPE    
  BertDDSSeekResultsTableEntry  

bertDDSSeekResultsTableIndex 1.3.6.1.4.1.351.110.6.1.27.1.1
Denotes the serial number of the entry in the table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..20  

bertDDSCode 1.3.6.1.4.1.351.110.6.1.27.1.2
Denotes the type of DDS code detected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER abnormalStationCondition(30), block(10), channelLoopback(40), dsuLoopback(44), farEndVoice(90), idle(126), loopbackEnable(86), mjuAlert(114), muxOutOfSync(26), ocuLoopback(42), release(120), test(28), testAlert(108), transitionInProgress(58), unassignedMuxChannel(24), unnamed(50)  

bertSupportedTestsTable 1.3.6.1.4.1.351.110.6.1.28
A list of supported tests for a given SM.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BertSupportedTestsTableEntry

bertSupportedTestsTableEntry 1.3.6.1.4.1.351.110.6.1.28.1
A general supported tests entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  BertSupportedTestsTableEntry  

bertSupportedTestsTableIndex 1.3.6.1.4.1.351.110.6.1.28.1.1
This index is the physical slot number of the Service Module whose entry it represents in the table. For MGX 8220, the range is 5-14. For MGX 8850, the range is 1-6, 9-14, 17-22, 25-30.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..30  

bertSupportFlag 1.3.6.1.4.1.351.110.6.1.28.1.2
'yes' if the table entry correctly represents the supported tests for the SM on the corresponding slot. 'no' if no tests at all are supported.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

bertTestMediumMask 1.3.6.1.4.1.351.110.6.1.28.1.3
Every test medium is represented by a bit of mask. Bits 0-1 are valid in this integer. The meaning of the mask can be understood from the example below: -------------------------- TestMedium | SM | support -------------------------- port | 1 line | 1 -------------------------- (Table contents applicable to FRSM-4T1) bertTestMediumMask = 11 binary The column titles represent the variables bertTestMedium depends on. The mask is represented in column major order.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bertModeMask 1.3.6.1.4.1.351.110.6.1.28.1.4
Every mode is represented by 2 bits of mask. Bits 0-5 are valid in this integer. The meaning of the mask can be understood from the example below: ----------------------------------------------------------- Mode | SM support | Test Medium: | | Multiple | | T1 time slots ----------------------------------------------------------- Pattern test | 1 | 1 DDS seek | 1 | 0 Loopback | 1 | 1 ----------------------------------------------------------- (Table contents applicable to FRSM-4T1) bertModeMask = 101111 binary The column titles represent the variables bertMode depends on. The mask is represented in column major order.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bertDeviceToLoopMask 1.3.6.1.4.1.351.110.6.1.28.1.5
Every class of devices to loop is represented by 6 bits of mask. Bits 0-29 are valid in this integer. The meaning of the mask can be understood from the example below: ----------------------------------------------------------- | | | Test Medium Class of | SM | MODE |________________________________ devices |supp | Loopback|Line |multiple T1 | 64k | 56k | | | | time slots | | ----------------------------------------------------------- noLatch | 1 0 0 0 0 1 latch | 1 1 0 0 1 1 v54 | 1 1 0 1 1 1 inband/esf| 1 1 1 0 0 0 metallic | 1 0 1 0 0 0 ----------------------------------------------------------- (Table contents applicable to FRSM-4T1) bertDeviceToLoopMask = 001110011000100110000111011111 binary The column titles represent the variables bertDeviceToLoop depends on. The mask is represented in column major order. Due to the limitation on the length of the mask, 'noDevice' option is not represented in this mask. But, the mask for it, is assumed to be a row of ones except for a zero on 'MODE Loopback' column.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bertPatternMask 1.3.6.1.4.1.351.110.6.1.28.1.6
Every class of patterns is represented by 2 bits of mask. Bits 0-3 are valid in this integer. The meaning of the mask can be understood from the example below: ---------------------------------------------- Class of | SM | Non latching patterns | support |device to loop ---------------------------------------------- Other patterns | 1 | 0 ---------------------------------------------- Patterns | 1 | 1 power 9 and 11 | | ---------------------------------------------- (Table contents applicable to FRSM-4T1) bertPatternMask = 1011 binary The column titles represent the variables bertPattern depends on. The mask is represented in column major order.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bertLoopbackMask 1.3.6.1.4.1.351.110.6.1.28.1.7
Every loopback is represented by 2 bits of mask. Bits 0-5 are valid in this integer. The meaning of the mask can be understood from the example below: ---------------------------------------------- Loopback | SM | Test Medium | support | Port ---------------------------------------------- Far End Loopback | 1 | 1 Facility Loopback | 1 | 1 Metallic Loopback | 1 | 0 ---------------------------------------------- (Table contents applicable to FRSM-4T1) bertLoopbackMask = 011111 binary The column titles represent the variables bertLoopback depends on. The mask is represented in column major order.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

bertCardT1E1Type 1.3.6.1.4.1.351.110.6.1.28.1.8
Specifies whether a t1 or e1 card.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER t1(1), e1(2)  

ciscoWanSrmBertMIBConformance 1.3.6.1.4.1.351.150.31.2
OBJECT IDENTIFIER    

ciscoWanSrmBertMIBGroups 1.3.6.1.4.1.351.150.31.2.1
OBJECT IDENTIFIER    

ciscoWanSrmBertMIBCompliances 1.3.6.1.4.1.351.150.31.2.2
OBJECT IDENTIFIER    

ciscoWanSrmBertCompliance 1.3.6.1.4.1.351.150.31.2.2.1
The compliance statement for objects related to Bert MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

ciscoWanSrmBertConfGroup 1.3.6.1.4.1.351.150.31.2.1.1
The collection of objects which are used for configuring/running BERT on Service modules using SRM module.
Status: current Access: read-only
OBJECT-GROUP    

ciscoWanSrmBertTestResultsGroup 1.3.6.1.4.1.351.150.31.2.1.2
The collection of objects which are used for finding the results of running BERT tests.
Status: current Access: read-only
OBJECT-GROUP    

ciscoWanSrmBertDDSResultsGroup 1.3.6.1.4.1.351.150.31.2.1.3
The collection of objects which are used for finding the results of running BERT tests using DDS pattern.
Status: current Access: read-only
OBJECT-GROUP