P2mpSnapshotCtrlEntry |
|
SEQUENCE |
|
|
|
|
p2mpSnapshotDspNum |
Integer32 |
|
|
p2mpSnapshotType |
P2mpSnapshotAttribute |
|
|
p2mpSnapshotDataScale |
CwrFixedPointScale |
|
|
p2mpSnapshotDataPrecision |
CwrFixedPointPrecision |
|
|
p2mpSnapshotOwner |
OwnerString |
|
|
p2mpSnapshotAction |
CwrCollectionAction |
|
|
p2mpSnapshotStatus |
CwrCollectionStatus |
|
|
p2mpSnapshotRowStatus |
RowStatus |
|
p2mpHistCtrlEntry |
1.3.6.1.4.1.9.9.180.1.1.1 |
This represents one entry in the p2mpHistCtrlTable. This table
is indexed by ifIndex, p2mpHistSuMacAddress, and p2mpHistClass.
At the head end:
Histograms can be created on each upstream channel either on a
per channel or per subscriber unit basis.
When histograms are created on a per subscriber unit basis, the
user must specify the subscriber unit's MAC address and the
ifIndex of the MAC layer (propDocsWirelessMaclayer) at the
head end.
When histograms are created on a per channel basis, the user
must set the MAC address to zero(00 00 00 00 00 00). The
channel ID is specified by the ifIndex of the upstream channel.
Hence, when creating histograms on a per channel basis, the
ifIndex must be set to the ifIndex of the upstream channel
(propDocsWirelessUpstream) on which the histogram is to be
created.
At the subscriber end:
Histograms can only be created on the downstream channel. Since
there is only one downstream channel, histograms cannot be
created per channel ID. Hence, when a histogram is created, the
user must set the MAC address (p2mpHistSuMacAdress) to
zero(00 00 00 00 00 00). The ifIndex must be set to the ifIndex
of the downstream channel (propDocsWirelessDownstream). |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
P2mpHistCtrlEntry |
|
|
p2mpHistSummaryEntry |
1.3.6.1.4.1.9.9.180.1.2.1 |
This represents one entry in the p2mpHistSummaryTable.
At the head end:
When viewing the summary of a histogram that was created for a
specific subscriber unit, the user must specify the subscriber
unit's MAC address and the ifIndex of the MAC layer at the
head end.
When viewing the summary of a histogram created for a specific
channel, the user must set the MAC address to zero
(00 00 00 00 00 00). The ifIndex is the upstream channel on
which the histogram was created.
At the subscriber end:
The user sets the MAC address (p2mpHistSuMacAdress) to
zero(00 00 00 00 00 00). The ifIndex is the channel ID of the
downstream channel. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
P2mpHistSummaryEntry |
|
|
p2mpHistDataEntry |
1.3.6.1.4.1.9.9.180.1.3.1 |
This represents one entry in the p2mpHistDataTable.
At the head end:
When viewing the data of a histogram that was created for a
specific subscriber unit, the user must specify the subscriber
unit's MAC address and the ifIndex of the MAC layer at the
head end.
When viewing the data of a histogram created for a specific
channel, the user must set the MAC address to zero
(00 00 00 00 00 00). The ifIndex is the upstream channel on
which the histogram was created.
At the subscriber end:
The user sets the MAC address (p2mpHistSuMacAdress) to
zero(00 00 00 00 00 00). The ifIndex is the channel ID of the
downstream channel. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
P2mpHistDataEntry |
|
|
p2mpTlCtrlEntry |
1.3.6.1.4.1.9.9.180.2.1.1 |
This represents one entry in the p2mpTlCtrlTable. This table
is indexed by ifIndex, p2mpTlSuMacAddress, and p2mpTlClass.
At the head end:
Timelines can be created on each upstream channel either on a
per channel or per subscriber unit basis.
When timelines are created on a per subscriber unit basis, the
user must specify the subscriber unit's MAC address and the
ifIndex of the MAC layer (propDocsWirelessMaclayer) at the
head end.
When timelines are created on a per channel basis, the user
must set the MAC address to zero(00 00 00 00 00 00). The channel
ID is specified by the ifIndex of the upstream channel. Hence,
when creating timelines on a per channel basis, the ifIndex must
be set to the ifIndex of the upstream channel on which the
timeline is to be created
At the subscriber end:
Timelines can only be created on the downstream channel. Since
there is only one downstream channel, timelines cannot be
created per channel ID. Hence, when a timeline is created, the
user must set the MAC address (p2mpTlSuMacAdress) to
zero(00 00 00 00 00 00). The ifIndex must be set to the ifIndex
of the downstream channel (propDocsWirelessDownstream). |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
P2mpTlCtrlEntry |
|
|
p2mpTlPostTrigBufMgmt |
1.3.6.1.4.1.9.9.180.2.1.1.10 |
Once a trigger fires, this object determines which portion of
the collected data to capture for use. If it is:
preTrigger(1) : Then most of the data collected prior to trigger
is captured.
postTrigger(2): Then most of the data collected after the trigger
is captured. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
preTrigger(1), postTrigger(2) |
|
p2mpTlSummaryEntry |
1.3.6.1.4.1.9.9.180.2.2.1 |
This represents one entry in the p2mpTlSummaryTable.
At the head end:
When viewing the summary of a timeline created for a specific
subscriber unit, the user must specify the subscriber unit's
MAC address and the ifIndex of the MAC layer at the head end.
When viewing the summary of a timeline created for a specific
channel, the user must set the MAC address to
zero(00 00 00 00 00 00). The ifIndex is the upstream channel on
which the timeline was created.
At the subscriber end:
The user sets the MAC address (p2mpTlSuMacAdress) to
zero(00 00 00 00 00 00). The ifIndex is the channel ID of the
downstream channel. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
P2mpTlSummaryEntry |
|
|
p2mpTlDataEntry |
1.3.6.1.4.1.9.9.180.2.3.1 |
This represents one entry in the p2mpTlDataTable.
At the head end:
When viewing the data of a timeline created for a specific
subscriber unit, the user must specify the subscriber unit's
MAC address and the ifIndex of the MAC layer at the head end.
When viewing the data of a timeline created for a specific
channel, the user must set the MAC address to
zero(00 00 00 00 00 00). The ifIndex is the upstream channel
on which the timeline was created.
At the subscriber end:
The user sets the MAC address (p2mpTlSuMacAdress) to
zero(00 00 00 00 00 00). The ifIndex is the channel ID of the
downstream channel. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
P2mpTlDataEntry |
|
|
p2mpThresholdEntry |
1.3.6.1.4.1.9.9.180.3.1.1 |
This represents one entry in the p2mpThresholdTable.
At the head end:
Thresholds can be created on each upstream channel either on a
per channel or per subscriber unit basis.
When creating thresholds on a per subscriber unit basis, the
user must specify the subscriber unit's MAC address and the
ifIndex of the MAC layer (propDocsWirelessMaclayer) at the
head end.
When creating thresholds on a per channel basis, the user
must set the MAC address to zero(00 00 00 00 00 00). The channel
ID is specified by the ifIndex of the upstream channel. Hence,
when creating thresholds on a per channel basis, the ifIndex must
be set to the ifIndex of the upstream channel
(propDocsWirelessUpstream) on which the threshold is created.
At the subscriber end:
Thresholds can only be created on the downstream channel. Since
there is only one downstream channel, thresholds cannot be
created per channel ID. Hence, when a thresholds is created, the
users sets the MAC address (p2mpThreshSuMacAdress) to
zero(00 00 00 00 00 00). The ifIndex must be set to the ifIndex
of the downstream channel (propDocsWirelessDownstream). |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
P2mpThresholdEntry |
|
|
p2mpSnapshotCtrlEntry |
1.3.6.1.4.1.9.9.180.4.1.1 |
This represents one entry in the p2mpSnapshotCntrlTable
It is indexed by the ifIndex of the MAC layer
(propDocsWirelessMaclayer) and p2mpSnapshotDspNum. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
P2mpSnapshotCtrlEntry |
|
|
p2mpSnapSummaryEntry |
1.3.6.1.4.1.9.9.180.4.2.1 |
This represents one entry in the p2mpSnapSummaryTable. It is
indexed by the ifIndex of the MAC layer
(propDocsWirelessMaclayer) and p2mpSnapshotDspNum. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
P2mpSnapSummaryEntry |
|
|
p2mpSnapDataEntry |
1.3.6.1.4.1.9.9.180.4.3.1 |
This represents one entry in the P2mpSnapDataTable. It is
indexed by ifIndex of the MAC layer (propDocsWirelessMaclayer),
p2mpSnapshotIndex, and p2mpSnapValueIndex.
The values in this table represent real and complex numbers.
If they are real numbers then p2mpRealPart contains the data and
p2mpImaginaryPart is undefined. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
P2mpSnapDataEntry |
|
|