CISCOSB-Physicaldescription-MIB

File: CISCOSB-Physicaldescription-MIB.mib (44464 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC MAU-MIB
CISCOSB-MIB CISCOSB-HWENVIROMENT ENTITY-SENSOR-MIB
IF-MIB CISCOSB-DEVICEPARAMS-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY TimeTicks
NOTIFICATION-TYPE DisplayString PhysAddress
RowStatus TruthValue JackType
switch001 rndNotifications RlEnvMonState
EntitySensorStatus EntitySensorValue InterfaceIndexOrZero
ifIndex InterfaceIndex rndErrorDesc
rndErrorSeverity

Defined Types

CascadePortState  
INTEGER error(0), init(1), down(2), active(3), standby(4)    

CascadePortSpeed  
INTEGER port-speed-10M(0), port-speed-100M(1), port-speed-1G(2), port-speed-10G(3), port-speed-12G(4), port-speed-2500M(5), port-speed-5G(6), port-speed-13600M(7), port-speed-20G(8), port-speed-40G(9), port-speed-16G(10), port-speed-15G(11), port-speed-75G(12), port-speed-100G(13), unknown(14)    

RlPhdModuleEntry  
SEQUENCE    
  rlPhdModuleStackUnit INTEGER
  rlPhdModuleIndex INTEGER
  rlPhdModuleType INTEGER
  rlPhdModuleStartingPort INTEGER
  rlPhdModuleNumberOfPorts INTEGER
  rlPhdModuleRow INTEGER
  rlPhdModuleColumn INTEGER
  rlPhdModuleRole INTEGER

RlPhdPortsEntry  
SEQUENCE    
  rlPhdPortsIfIndex INTEGER
  rlPhdPortsIfIndexName DisplayString Size(1..20)
  rlPhdPortsMediaType INTEGER
  rlPhdPortsStackUnit INTEGER
  rlPhdPortsModuleNumber INTEGER
  rlPhdPortsRow INTEGER
  rlPhdPortsColumn INTEGER
  rlPhdConnectorType JackType
  rlPhdPortHaul INTEGER

RlPhdStackEntry  
SEQUENCE    
  rlPhdStackUnit INTEGER
  rlPhdStackType INTEGER
  rlPhdStackConnect1 INTEGER
  rlPhdStackConnect2 INTEGER
  rlPhdStackSofrwareVer DisplayString
  rlPhdStackProductID DisplayString
  rlPhdStackMacAddr PhysAddress

RlPhdModuleHotSwapEntry  
SEQUENCE    
  rlPhdModuleHotSwapAdminStatus INTEGER
  rlPhdModuleHotSwapOperStatus INTEGER

RlPhdStackOrderEntry  
SEQUENCE    
  rlPhdStackOrderCurrentUnitPosition INTEGER
  rlPhdStackOrderDesiredUnitPosition INTEGER
  rlPhdStackOrderUnitIndex INTEGER
  rlPhdStackOrderUnitType INTEGER

RlPhdUnitGenParamEntry  
SEQUENCE    
  rlPhdUnitGenParamStackUnit INTEGER
  rlPhdUnitGenParamSoftwareVersion DisplayString
  rlPhdUnitGenParamFirmwareVersion DisplayString
  rlPhdUnitGenParamHardwareVersion DisplayString
  rlPhdUnitGenParamSerialNum DisplayString
  rlPhdUnitGenParamAssetTag DisplayString
  rlPhdUnitGenParamServiceTag DisplayString
  rlPhdUnitGenParamSoftwareDate DisplayString
  rlPhdUnitGenParamFirmwareDate DisplayString
  rlPhdUnitGenParamManufacturer DisplayString
  rlPhdUnitGenParamModelName DisplayString
  rlPhdUnitGenParamMd5ChksumBoot DisplayString
  rlPhdUnitGenParamMd5ChksumImage1 DisplayString
  rlPhdUnitGenParamMd5ChksumImage2 DisplayString
  rlPhdUnitGenParamRegistrationDone TruthValue
  rlPhdUnitGenParamRegistrationSuppressed TruthValue

RlPhdUnitEnvParamEntry  
SEQUENCE    
  rlPhdUnitEnvParamStackUnit INTEGER
  rlPhdUnitEnvParamMainPSStatus RlEnvMonState
  rlPhdUnitEnvParamRedundantPSStatus RlEnvMonState
  rlPhdUnitEnvParamFan1Status RlEnvMonState
  rlPhdUnitEnvParamFan2Status RlEnvMonState
  rlPhdUnitEnvParamFan3Status RlEnvMonState
  rlPhdUnitEnvParamFan4Status RlEnvMonState
  rlPhdUnitEnvParamFan5Status RlEnvMonState
  rlPhdUnitEnvParamTempSensorValue EntitySensorValue
  rlPhdUnitEnvParamTempSensorStatus EntitySensorStatus
  rlPhdUnitEnvParamUpTime TimeTicks
  rlPhdUnitEnvParamMonitorAutoRecoveryEnable TruthValue
  rlPhdUnitEnvParamMonitorTemperatureStatus INTEGER
  rlPhdUnitEnvParamMonitorOperStatus TruthValue

RlPhdPoeEntry  
SEQUENCE    
  rlPhdPoeStackUnit INTEGER
  rlPhdPoePresent INTEGER

RlCascadeEntry  
SEQUENCE    
  rlCascadeNeighborIfIndex InterfaceIndexOrZero
  rlCascadeNeighborUnit INTEGER
  rlCascadeTrunkId INTEGER
  rlCascadeUnitId INTEGER
  rlCascadePortSpeed CascadePortSpeed
  rlCascadePortState CascadePortState

RlCascadeAfterResetEntry  
SEQUENCE    
  rlCascadeIfIndexAfterReset InterfaceIndex
  rlCascadeTrunkIdAfterReset INTEGER
  rlCascadeRowStatus RowStatus

StackPortType  
INTEGER port-type-100M(0), port-type-1G(1), port-type-5G(2), port-type-10G(3)    

ConnectionType  
INTEGER copper(1), combo-copper(2), combo-fiber(3), fiber(4), direct-attached(5)    

RlPhdUnitStackPortEntry  
SEQUENCE    
  rlPhdUnitStackPortName DisplayString
  rlPhdUnitStackPortType StackPortType
  rlPhdUnitStackPortConnectionType ConnectionType
  rlPhdUnitStackPortColumn INTEGER
  rlPhdUnitStackPortRow INTEGER

Defined Values

rlPhysicalDescription 1.3.6.1.4.1.9.6.1.101.53
The private MIB module definition for physical device configuration.
MODULE-IDENTITY    

rlPhdMibVersion 1.3.6.1.4.1.9.6.1.101.53.1
MIB's version, the current version is 3. 1: original version 2: a. new tables rlPhdModuleHotSwapTable rlPhdStackOrderTable b. new scalars rlPhdStackReorder rlPhdNumberOfUnits rlPhdMaxNumberOfUnits 3: a. new field rlPhdModuleRole of rlPhdModuleTable b. new scalars rlPhdForceMasterUnit 4: a. new fields rlPhdModuleConnect1 and rlPhdModuleConnect2 of rlPhdModuleTable. 5: a. Prefix rlPhD were replaced by prefix rlPhd b. fields rlPhdModuleConnect1 and rlPhdModuleConnect2 are moved from rlPhdModuleTable to rlPhdStackTable. c. new fiels rlPhdStackSofrwareVer, rlPhdStackProductID and rlPhdStackMacAddr of rlPhdStackTable. d. new scalars rlPhdStackReloadUnit e. new scalars rlPhdStackOrderTopUnit rlPhdStackOrderBottomUnit rlPhdStackOrderPermutation
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdModuleTable 1.3.6.1.4.1.9.6.1.101.53.2
For each module (board) there is an entry describing it in this module
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlPhdModuleEntry

rlPhdModuleEntry 1.3.6.1.4.1.9.6.1.101.53.2.1
A entry of this table specifies a module (board)
Status: current Access: not-accessible
OBJECT-TYPE    
  RlPhdModuleEntry  

rlPhdModuleStackUnit 1.3.6.1.4.1.9.6.1.101.53.2.1.1
The number of the stack unit
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdModuleIndex 1.3.6.1.4.1.9.6.1.101.53.2.1.2
The number of the module in its stack unit
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdModuleType 1.3.6.1.4.1.9.6.1.101.53.2.1.3
The index for each module type
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdModuleStartingPort 1.3.6.1.4.1.9.6.1.101.53.2.1.4
The minimal number of the port residing on this module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdModuleNumberOfPorts 1.3.6.1.4.1.9.6.1.101.53.2.1.5
The number of ports residing on this module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdModuleRow 1.3.6.1.4.1.9.6.1.101.53.2.1.6
On which row (the uppermost being numbered 1 and the highest row number asigned to the lowest row) this module resides within the chassis of its stack unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdModuleColumn 1.3.6.1.4.1.9.6.1.101.53.2.1.7
On which column (the leftmost being numbered 1 and the highest column number asigned to the rightmost column) this module resides within the chassis of its stack unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdModuleRole 1.3.6.1.4.1.9.6.1.101.53.2.1.8
The module role in the stack.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER standalone(1), master(2), backup(3), slave(4)  

rlPhdPortsTable 1.3.6.1.4.1.9.6.1.101.53.3
Lists the physical or physical-related attributes of ports
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlPhdPortsEntry

rlPhdPortsEntry 1.3.6.1.4.1.9.6.1.101.53.3.1
For each port, a entry describing attributes which are either physical or are derived from the features of the device hardware
Status: current Access: not-accessible
OBJECT-TYPE    
  RlPhdPortsEntry  

rlPhdPortsIfIndex 1.3.6.1.4.1.9.6.1.101.53.3.1.1
The L2 interface number associated with this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdPortsIfIndexName 1.3.6.1.4.1.9.6.1.101.53.3.1.2
The L2 interface number associated with this port, in string format based on the overall hardware architecture of the device (i.e., for monolithic devices just numbers, devices composed of modules (boards, cards) or stackable devices composed of monolithic units in form - , stackable devices in which each unit is composed of modules - -
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..20)  

rlPhdPortsMediaType 1.3.6.1.4.1.9.6.1.101.53.3.1.3
The media type of this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER copper(1), optic-fiber(2), combo(3)  

rlPhdPortsStackUnit 1.3.6.1.4.1.9.6.1.101.53.3.1.4
The number of the slot to which this port belongs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdPortsModuleNumber 1.3.6.1.4.1.9.6.1.101.53.3.1.5
The number of the stack unit to which this port resides in.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdPortsRow 1.3.6.1.4.1.9.6.1.101.53.3.1.6
On which row (the uppermost being numbered 1 and the highest row number asigned to the lowest row) this port resides within its module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdPortsColumn 1.3.6.1.4.1.9.6.1.101.53.3.1.7
On which column (the leftmost being numbered 1 and the highest column number asigned to the rightmost column) this this port resides within its module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdConnectorType 1.3.6.1.4.1.9.6.1.101.53.3.1.8
Type of connector.
Status: current Access: read-only
OBJECT-TYPE    
  JackType  

rlPhdPortHaul 1.3.6.1.4.1.9.6.1.101.53.3.1.9
Distance supported by this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-relevant(1), short(2), long(3)  

rlPhdStackTable 1.3.6.1.4.1.9.6.1.101.53.4
For each stack unit there is an entry describing it in this table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlPhdStackEntry

rlPhdStackEntry 1.3.6.1.4.1.9.6.1.101.53.4.1
A entry of this table specifies a stack unit
Status: current Access: not-accessible
OBJECT-TYPE    
  RlPhdStackEntry  

rlPhdStackUnit 1.3.6.1.4.1.9.6.1.101.53.4.1.1
The stack unit described by this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdStackType 1.3.6.1.4.1.9.6.1.101.53.4.1.2
The type of the stack unit described by this entry: 1 - box 3202 2 - box LG 3 - bcm 4 - prestera
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdStackConnect1 1.3.6.1.4.1.9.6.1.101.53.4.1.3
The unit number connected to the Hyper GLink left side connection - 0 means not connected; other integer indicates the unit number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdStackConnect2 1.3.6.1.4.1.9.6.1.101.53.4.1.4
The unit number connected to the Hyper GLink right side connection - 0 means not connected; other integer indicates the unit number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdStackSofrwareVer 1.3.6.1.4.1.9.6.1.101.53.4.1.5
The Software version of the unit.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..20)  

rlPhdStackProductID 1.3.6.1.4.1.9.6.1.101.53.4.1.6
The Product ID of the unit.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..20)  

rlPhdStackMacAddr 1.3.6.1.4.1.9.6.1.101.53.4.1.7
The physical (MAC) address of the unit.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

rlPhdModuleHotSwapTable 1.3.6.1.4.1.9.6.1.101.53.5
For each module (board) there is an entry describing its Hot Swap status
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlPhdModuleHotSwapEntry

rlPhdModuleHotSwapEntry 1.3.6.1.4.1.9.6.1.101.53.5.1
A entry of this table specifies a module (board) Hot Swap status
Status: current Access: not-accessible
OBJECT-TYPE    
  RlPhdModuleHotSwapEntry  

rlPhdModuleHotSwapAdminStatus 1.3.6.1.4.1.9.6.1.101.53.5.1.1
The desired state of the module. The off(1) state indicates that the module is not used and its rlPhdModuleHotSwapOperStatus is always off(2). The on{1) state indicates that the module may be used and its rlPhdModuleHotSwapOperStatus will be on(1) if it presents and off(2) if it does not present.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

rlPhdModuleHotSwapOperStatus 1.3.6.1.4.1.9.6.1.101.53.5.1.2
The current Hot Swap state of the module. If rlPhdModuleHotSwapAdminStatus is down(2) then rlPhdModuleHotSwapOperStatus should be down(2). If rlPhdModuleHotSwapAdminStatus is changed to up(1) then rlPhdModuleHotSwapOperStatus should change to up(1) if the module presents; it should remain in the down(2) state if and only if the module does not present.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

rlPhdStackOrderTable 1.3.6.1.4.1.9.6.1.101.53.6
This table enables the user to configure the order of the stack units as displayed on his GUI. The order of the entries in this table corresponds to the last configured order. If the stack units order was never configured, the order will be the same as in the rlPhdStackTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlPhdStackOrderEntry

rlPhdStackOrderEntry 1.3.6.1.4.1.9.6.1.101.53.6.1
A entry of this table specifies a stack unit in the position desired by the user
Status: current Access: not-accessible
OBJECT-TYPE    
  RlPhdStackOrderEntry  

rlPhdStackOrderCurrentUnitPosition 1.3.6.1.4.1.9.6.1.101.53.6.1.1
The current stack unit position.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

rlPhdStackOrderDesiredUnitPosition 1.3.6.1.4.1.9.6.1.101.53.6.1.2
The desired stack unit position. Note that setting this MIB object will take effect only after setting the rlPhdStackReorder MIB object below. After setting this MIB object and until a further change of at least one instance of the rlPhdStackOrderDesiredUnitPosition object, the values of the rlPhdStackOrderCurrentUnitPosition objectinstance and the corresponding rlPhdStackOrderDesiredUnitPosition object instance will be the same.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rlPhdStackOrderUnitIndex 1.3.6.1.4.1.9.6.1.101.53.6.1.3
This is the original unit index, i.e. has the same value as rlPhdStackUnit above.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

rlPhdStackOrderUnitType 1.3.6.1.4.1.9.6.1.101.53.6.1.4
The type of the stack unit described by this entry. It has the same value as rlPhdStackType above. This information is duplicated here only for easier retrieval by the device manager.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdStackReorder 1.3.6.1.4.1.9.6.1.101.53.7
Setting this MIB object will cause the settings of the rlPhdStackOrderDesiredUnitPosition MIB object instances to take effect. After setting this MIB object and until a further change of at least one instance of the rlPhdStackOrderDesiredUnitPosition object, the values of the rlPhdStackOrderCurrentUnitPosition objectinstance and the corresponding rlPhdStackOrderDesiredUnitPosition object instance will be the same.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reorder(1)  

rlPhdNumberOfUnits 1.3.6.1.4.1.9.6.1.101.53.8
Shows the current number of units in the stack.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdMaxNumberOfUnits 1.3.6.1.4.1.9.6.1.101.53.9
Shows the maximum number of units in the stack.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdForceMasterUnit 1.3.6.1.4.1.9.6.1.101.53.10
Force unit to be master.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rlPhdStackFixedUnit 1.3.6.1.4.1.9.6.1.101.53.11
Determine which unit will be on bottom/top of list on Show-List command(see .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rlPhdStackFixedUnitLocation 1.3.6.1.4.1.9.6.1.101.53.12
Determine the bottom/top object in the stack table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER bottom(1), top(2)  

rlPhdStackReloadUnit 1.3.6.1.4.1.9.6.1.101.53.13
Reset a specific unit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rlPhdUnitGenParamTable 1.3.6.1.4.1.9.6.1.101.53.14
For each module (board) there is an entry describing it in this module
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlPhdUnitGenParamEntry

rlPhdUnitGenParamEntry 1.3.6.1.4.1.9.6.1.101.53.14.1
A entry of this table specifies a module (board)
Status: current Access: not-accessible
OBJECT-TYPE    
  RlPhdUnitGenParamEntry  

rlPhdUnitGenParamStackUnit 1.3.6.1.4.1.9.6.1.101.53.14.1.1
The index of the stack unit to which this conceptual row corresponds.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdUnitGenParamSoftwareVersion 1.3.6.1.4.1.9.6.1.101.53.14.1.2
Serial number of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamFirmwareVersion 1.3.6.1.4.1.9.6.1.101.53.14.1.3
Serial number of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamHardwareVersion 1.3.6.1.4.1.9.6.1.101.53.14.1.4
Serial number of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamSerialNum 1.3.6.1.4.1.9.6.1.101.53.14.1.5
Serial number of the product.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamAssetTag 1.3.6.1.4.1.9.6.1.101.53.14.1.6
Serial number of the product.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamServiceTag 1.3.6.1.4.1.9.6.1.101.53.14.1.7
Asset tag of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamSoftwareDate 1.3.6.1.4.1.9.6.1.101.53.14.1.8
Date of product's software.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamFirmwareDate 1.3.6.1.4.1.9.6.1.101.53.14.1.9
Date of product's firmware.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamManufacturer 1.3.6.1.4.1.9.6.1.101.53.14.1.10
Product's Manufacturer.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamModelName 1.3.6.1.4.1.9.6.1.101.53.14.1.11
Model Name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamMd5ChksumBoot 1.3.6.1.4.1.9.6.1.101.53.14.1.12
MD5 Checksum for Boot
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamMd5ChksumImage1 1.3.6.1.4.1.9.6.1.101.53.14.1.13
MD5 Checksum for Image 1
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamMd5ChksumImage2 1.3.6.1.4.1.9.6.1.101.53.14.1.14
MD5 Checksum for Image 2
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rlPhdUnitGenParamRegistrationDone 1.3.6.1.4.1.9.6.1.101.53.14.1.15
Registration Done.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

rlPhdUnitGenParamRegistrationSuppressed 1.3.6.1.4.1.9.6.1.101.53.14.1.16
Registration Suppressed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

rlPhdUnitEnvParamTable 1.3.6.1.4.1.9.6.1.101.53.15
For each module (board) there is an entry describing it in this module
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlPhdUnitEnvParamEntry

rlPhdUnitEnvParamEntry 1.3.6.1.4.1.9.6.1.101.53.15.1
A entry of this table specifies a module (board)
Status: current Access: not-accessible
OBJECT-TYPE    
  RlPhdUnitEnvParamEntry  

rlPhdUnitEnvParamStackUnit 1.3.6.1.4.1.9.6.1.101.53.15.1.1
The index of the stack unit to which this conceptual row corresponds. Note that the index will be the same index as the index of a 'chassis' physical entity in the entity MIB of the product.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdUnitEnvParamMainPSStatus 1.3.6.1.4.1.9.6.1.101.53.15.1.2
The mandatory state of the main PS being instrumented.
Status: current Access: read-only
OBJECT-TYPE    
  RlEnvMonState  

rlPhdUnitEnvParamRedundantPSStatus 1.3.6.1.4.1.9.6.1.101.53.15.1.3
The mandatory state of the redundant PS being instrumented.
Status: current Access: read-only
OBJECT-TYPE    
  RlEnvMonState  

rlPhdUnitEnvParamFan1Status 1.3.6.1.4.1.9.6.1.101.53.15.1.4
The mandatory state of the FAN 1 being instrumented.
Status: current Access: read-only
OBJECT-TYPE    
  RlEnvMonState  

rlPhdUnitEnvParamFan2Status 1.3.6.1.4.1.9.6.1.101.53.15.1.5
The mandatory state of the FAN 2 being instrumented.
Status: current Access: read-only
OBJECT-TYPE    
  RlEnvMonState  

rlPhdUnitEnvParamFan3Status 1.3.6.1.4.1.9.6.1.101.53.15.1.6
The mandatory state of the FAN 3 being instrumented.
Status: current Access: read-only
OBJECT-TYPE    
  RlEnvMonState  

rlPhdUnitEnvParamFan4Status 1.3.6.1.4.1.9.6.1.101.53.15.1.7
The mandatory state of the FAN 4 being instrumented.
Status: current Access: read-only
OBJECT-TYPE    
  RlEnvMonState  

rlPhdUnitEnvParamFan5Status 1.3.6.1.4.1.9.6.1.101.53.15.1.8
The mandatory state of the FAN 5 being instrumented.
Status: current Access: read-only
OBJECT-TYPE    
  RlEnvMonState  

rlPhdUnitEnvParamTempSensorValue 1.3.6.1.4.1.9.6.1.101.53.15.1.9
Current value for the Sensor being instrumented.
Status: current Access: read-only
OBJECT-TYPE    
  EntitySensorValue  

rlPhdUnitEnvParamTempSensorStatus 1.3.6.1.4.1.9.6.1.101.53.15.1.10
Status value for the Sensor being instrumented.
Status: current Access: read-only
OBJECT-TYPE    
  EntitySensorStatus  

rlPhdUnitEnvParamUpTime 1.3.6.1.4.1.9.6.1.101.53.15.1.11
Up time of the unit in 100th of second (sec/100).
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

rlPhdUnitEnvParamMonitorAutoRecoveryEnable 1.3.6.1.4.1.9.6.1.101.53.15.1.12
Disable environment automatic recovery option
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

rlPhdUnitEnvParamMonitorTemperatureStatus 1.3.6.1.4.1.9.6.1.101.53.15.1.13
Display environment monitoring chassis temperature status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), overTemperatureThreshold(2), overCriticalTemperatureThreshold(3)  

rlPhdUnitEnvParamMonitorOperStatus 1.3.6.1.4.1.9.6.1.101.53.15.1.14
Display environment automatic recovery current status (active/not active)
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

rlPhdStackOrderTopUnit 1.3.6.1.4.1.9.6.1.101.53.16
This scalar mib holds the Top unit for the stack order command
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rlPhdStackOrderBottomUnit 1.3.6.1.4.1.9.6.1.101.53.17
This scalar mib holds the Bottom unit for the stack order command
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rlPhdStackOrderPermutation 1.3.6.1.4.1.9.6.1.101.53.18
This scalar mib holds stack permutation
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

rlPhdNumberOfPoeUnits 1.3.6.1.4.1.9.6.1.101.53.19
Shows the current number of poe units in the stack.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdPoeTable 1.3.6.1.4.1.9.6.1.101.53.20
For each module (board) there is an entry describing it in this module
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlPhdPoeEntry

rlPhdPoeEntry 1.3.6.1.4.1.9.6.1.101.53.20.1
A entry of this table specifies a module (board)
Status: current Access: not-accessible
OBJECT-TYPE    
  RlPhdPoeEntry  

rlPhdPoeStackUnit 1.3.6.1.4.1.9.6.1.101.53.20.1.1
The stack unit to which this module belongs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdPoePresent 1.3.6.1.4.1.9.6.1.101.53.20.1.2
The present state of the PoE module. The no(1) state indicates that the PoE module is not present. The yes{2) state indicates that the PoE module is present.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

rlPhdPhyLedStackUnit 1.3.6.1.4.1.9.6.1.101.53.21
This scalar mib holds the unit number for the stack light command
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rlPhdPhyLedTimeout 1.3.6.1.4.1.9.6.1.101.53.22
This scalar mib holds the timeout for the stack light command. May be in the range 2..60 sec. (default - 5 sec.), if the timeout = 0 - all units return to normal state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rlCascadeTable 1.3.6.1.4.1.9.6.1.101.53.23
For each cascaded port for stacking unit there is an entry describing it in this table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlCascadeEntry

rlCascadeEntry 1.3.6.1.4.1.9.6.1.101.53.23.1
An entry of this table specifies a cascaded link information in a unit
Status: current Access: not-accessible
OBJECT-TYPE    
  RlCascadeEntry  

rlCascadeNeighborIfIndex 1.3.6.1.4.1.9.6.1.101.53.23.1.1
The ifIndex of a stacking port in the neighbor unit - 0 means not connected; other integer indicates the IfIndex.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

rlCascadeNeighborUnit 1.3.6.1.4.1.9.6.1.101.53.23.1.2
The unit number of the neighbor unit - 0 means not connected; other integer indicates the unit number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlCascadeTrunkId 1.3.6.1.4.1.9.6.1.101.53.23.1.3
The id of the trunk, the stacking port is member, zero if the port is not member of trunk.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlCascadeUnitId 1.3.6.1.4.1.9.6.1.101.53.23.1.4
The unit number matching the current ifIndex
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlCascadePortSpeed 1.3.6.1.4.1.9.6.1.101.53.23.1.5
Port speed
Status: current Access: read-only
OBJECT-TYPE    
  CascadePortSpeed  

rlCascadePortState 1.3.6.1.4.1.9.6.1.101.53.23.1.6
Port state according to cascade LAG state machine
Status: current Access: read-only
OBJECT-TYPE    
  CascadePortState  

rlCascadeAfterResetTable 1.3.6.1.4.1.9.6.1.101.53.24
For each cascaded port for stacking unit there is an entry describing it in this table after reset
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlCascadeAfterResetEntry

rlCascadeAfterResetEntry 1.3.6.1.4.1.9.6.1.101.53.24.1
A entry of this table specifies a cascaded port information in a unit after reset
Status: current Access: not-accessible
OBJECT-TYPE    
  RlCascadeAfterResetEntry  

rlCascadeIfIndexAfterReset 1.3.6.1.4.1.9.6.1.101.53.24.1.1
The ifIndex of a stacking port after reset.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

rlCascadeTrunkIdAfterReset 1.3.6.1.4.1.9.6.1.101.53.24.1.2
The Id of the trunk, the stacking port will be member after reset, zero if the port is not member of trunk.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rlCascadeRowStatus 1.3.6.1.4.1.9.6.1.101.53.24.1.3
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

rlStackUnitRemoved 1.3.6.1.4.1.9.6.1.101.0.186
Trap indicating that a unit was removed from the stack.
Status: current Access: read-create
NOTIFICATION-TYPE    

rlStackConfigChangedRingChain 1.3.6.1.4.1.9.6.1.101.0.187
Trap indicating that the configuration of the stack has changed. - from ring to chain - from chain to ring.
Status: current Access: read-create
NOTIFICATION-TYPE    

rlStackBackupUnitRemoved 1.3.6.1.4.1.9.6.1.101.0.188
Trap indicating that the backup unit was removed from the stack.
Status: current Access: read-create
NOTIFICATION-TYPE    

rlStackMasterSwitchover 1.3.6.1.4.1.9.6.1.101.0.189
Trap indicating that a new master was elected. The old maste is the backup now.
Status: current Access: read-create
NOTIFICATION-TYPE    

rlStackUnitDifferentSwVersion 1.3.6.1.4.1.9.6.1.101.0.190
Trap indicating that the new unit added to the stack has different software version than the master.
Status: current Access: read-create
NOTIFICATION-TYPE    

rlStackDuplicateUnitNotJoin 1.3.6.1.4.1.9.6.1.101.0.191
Trap indicating that a new unit with duplicated unit id was added to the stack - but it will not join the stack.
Status: current Access: read-create
NOTIFICATION-TYPE    

rlStackLinkChange 1.3.6.1.4.1.9.6.1.101.0.195
Trap indicating that Link has change in one of the Stacking Ports.
Status: current Access: read-create
NOTIFICATION-TYPE    

rlPhdUnitStackPortTable 1.3.6.1.4.1.9.6.1.101.53.25
The table listing information required for stack port. The index for the table is ifindex; the ports that represented in that table are operational stack ports or ports that can be stack ports after reset
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlPhdUnitStackPortEntry

rlPhdUnitStackPortEntry 1.3.6.1.4.1.9.6.1.101.53.25.1
An entry in rlPhdUnitStackPortTable
Status: current Access: not-accessible
OBJECT-TYPE    
  RlPhdUnitStackPortEntry  

rlPhdUnitStackPortName 1.3.6.1.4.1.9.6.1.101.53.25.1.1
Stack port name
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..50)  

rlPhdUnitStackPortType 1.3.6.1.4.1.9.6.1.101.53.25.1.2
Stack port type
Status: current Access: read-only
OBJECT-TYPE    
  StackPortType  

rlPhdUnitStackPortConnectionType 1.3.6.1.4.1.9.6.1.101.53.25.1.3
Operational connection type (copper(1), combo-copper(2), combo-fiber(3), fiber(4), direct-Attached(5))
Status: current Access: read-only
OBJECT-TYPE    
  ConnectionType  

rlPhdUnitStackPortRow 1.3.6.1.4.1.9.6.1.101.53.25.1.4
On which row (the uppermost being numbered 1 and the highest row number assigned to the lowest row) this actual/candidate cascade port resides within the chassis of its stack unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rlPhdUnitStackPortColumn 1.3.6.1.4.1.9.6.1.101.53.25.1.5
On which column (the leftmost being numbered 1 and the highest column number assigned to the rightmost column) this actual/candidate cascade port resides within the chassis of its stack unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER