COM21-HCXOC3-MIB

File: COM21-HCXOC3-MIB.mib (50186 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	COM21-HCX-MIB
COM21-HCXALM-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Integer32	IpAddress	Gauge32
TimeTicks	DisplayString	MacAddress
com21	com21Hcx	com21Traps
hcxAlmSeverity	hcxEventLogTime

Defined Types

PrimServiceState
INTEGER	is(1), oos(2)

Com21RowStatus
INTEGER	active(1), create(2), destroy(3), deactive(4)

HcxOc3UnitEntry
SEQUENCE
	hcxOc3UnitShelfId	INTEGER
	hcxOc3UnitSlotId	Integer32
	hcxOc3HardwareVersion	DisplayString
	hcxOc3BootVersion	DisplayString
	hcxOc3UnitPrimServState	PrimServiceState
	hcxOc3UnitSecServState	DisplayString
	hcxOc3RestartAction	INTEGER
	hcxOc3TestStatusLed	INTEGER
	hcxOc3FaultStatusLed	INTEGER
	hcxOc3SerialNumber	DisplayString
	hcxOc3SyncClkConfigure	INTEGER

HcxOc3PortEntry
SEQUENCE
	hcxOc3PortShelfId	INTEGER
	hcxOc3PortSlotId	Integer32
	hcxOc3PortId	INTEGER
	hcxOc3PortPrimServState	PrimServiceState
	hcxOc3PortSecServState	DisplayString
	hcxOc3MaxBandwidth	INTEGER
	hcxOc3AggrDnStrmCbrRate	Integer32
	hcxOc3AggrDnStrmPcrRate	Integer32
	hcxOc3AggrUpStrmCbrRate	Integer32
	hcxOc3AggrUpStrmMinRate	Integer32
	hcxOc3AggrUpStrmMaxRate	Integer32
	hcxOc3AgeTime	Integer32
	hcxOc3PortConfigState	INTEGER
	hcxOc3PortRestartAction	INTEGER
	hcxOc3PortDiagTestAction	INTEGER
	hcxOc3PortDiagTestResult	INTEGER
	hcxOc3PortLOSLed	INTEGER
	hcxOc3AggrActDnStrmCbrRate	Integer32
	hcxOc3AggrActDnStrmPcrRate	Integer32
	hcxOc3AggrActUpStrmCbrRate	Integer32
	hcxOc3AggrActUpStrmMinRate	Integer32
	hcxOc3AggrActUpStrmMaxRate	Integer32
	hcxOc3PortIpAddr	IpAddress
	hcxOc3PortIpMask	IpAddress
	hcxOc3PortMacAddr	MacAddress
	hcxOc3Port1483EncapEnbl	INTEGER
	hcxOc3PortSectionLOS	INTEGER
	hcxOc3PortSectionLOF	INTEGER
	hcxOc3PortLineAIS	INTEGER
	hcxOc3PortLineRDI	INTEGER
	hcxOc3PortPathRDI	INTEGER
	hcxOc3PortAggrVoiceRate	Integer32
	hcxOc3PortAggrActVoiceRate	Integer32
	hcxOc3PortLOFLed	INTEGER

HcxOc3VccEntry
SEQUENCE
	hcxOc3VccShelfId	Integer32
	hcxOc3VccSlotId	Integer32
	hcxOc3VccPortId	Integer32
	hcxOc3VccVpi	Integer32
	hcxOc3VccVci	Integer32
	hcxOc3VccType	INTEGER

HcxOc3StatsEntry
SEQUENCE
	hcxOc3StatsShelfId	Integer32
	hcxOc3StatsSlotId	Integer32
	hcxOc3StatsPortId	Integer32
	hcxOc3StatsCurrSectionBIPErr	Integer32
	hcxOc3StatsCurrLineBIPErr	Integer32
	hcxOc3StatsCurrPathBIPErr	Integer32
	hcxOc3StatsCurrLineFEndBlockErr	Integer32
	hcxOc3StatsCurrPathFEndBlockErr	Integer32
	hcxOc3StatsPrevSectionBIPErr	Integer32
	hcxOc3StatsPrevLineBIPErr	Integer32
	hcxOc3StatsPrevPathBIPErr	Integer32
	hcxOc3StatsPrevLineFEndBlockErr	Integer32
	hcxOc3StatsPrevPathFEndBlockErr	Integer32
	hcxOc3StatsClear	INTEGER

Defined Values

com21HcxOc3		1.3.6.1.4.1.1141.2.90
This is the Com21 ComController Oc3 MIB module. COM21 Part# 005-0025-00
MODULE-IDENTITY

com21HcxOc3UnitGroup		1.3.6.1.4.1.1141.2.91
OBJECT IDENTIFIER

com21HcxOc3PortGroup		1.3.6.1.4.1.1141.2.92
OBJECT IDENTIFIER

com21HcxOc3VccGroup		1.3.6.1.4.1.1141.2.93
OBJECT IDENTIFIER

com21HcxOc3StatsGroup		1.3.6.1.4.1.1141.2.94
OBJECT IDENTIFIER

com21HcxOc3UnitTable		1.3.6.1.4.1.1141.2.91.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HcxOc3UnitEntry

com21HcxOc3UnitEntry		1.3.6.1.4.1.1141.2.91.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	HcxOc3UnitEntry

hcxOc3UnitShelfId		1.3.6.1.4.1.1141.2.91.1.1.1
contains the associated shelf id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1

hcxOc3UnitSlotId		1.3.6.1.4.1.1141.2.91.1.1.2
contains associated slot id.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3HardwareVersion		1.3.6.1.4.1.1141.2.91.1.1.3
contains the hardware version of the Oc3 card. Will contain empty string if card has not been inserted in the slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

hcxOc3BootVersion		1.3.6.1.4.1.1141.2.91.1.1.4
contains the version of the Oc3 card boot ROM. Will contain empty string if card has not been inserted in the slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

hcxOc3UnitPrimServState		1.3.6.1.4.1.1141.2.91.1.1.5
contains primary service state of the Oc3 Unit.
Status: current	Access: read-only
OBJECT-TYPE
	PrimServiceState

hcxOc3UnitPrimStateChange		1.3.6.1.4.1.1141.4.150
This trap is generated whenever a change in the the hcxOc3UnitPrimServState occurs. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3UnitSecServState		1.3.6.1.4.1.1141.2.91.1.1.6
contains a string defining the secondary service states of the Oc3 Unit. The substrings supported by the Oc3 Unit shall be: UNEQ - unequipped.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

hcxOc3UnitSecStateChange		1.3.6.1.4.1.1141.4.151
This trap is generated whenever a change in the the hcxOc3UnitSecServState occurs. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3RestartAction		1.3.6.1.4.1.1141.2.91.1.1.7
The Oc3 Unit Restart Action is an active-value. The setting of this attribute to restart(2) causes the Oc3 card to reset and download a new image.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nil(1), restart(2)

hcxOc3TestStatusLed		1.3.6.1.4.1.1141.2.91.1.1.8
The Oc3 Test Status LED is a read-only attribute which describes the condition of the Oc3 Test Status light emitting diode located on the Oc3 board. A value of on(1) indicates that a service effecting test is in progress and that the LED is illuminated. Will be off if no card present.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxOc3TestStatusLedChange		1.3.6.1.4.1.1141.4.152
generated whenever there is a change in test LED status. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3FaultStatusLed		1.3.6.1.4.1.1141.2.91.1.1.9
The Oc3 Fault Status LED is a read-only attribute which describes the condition of the Oc3 Fault Status light emitting diode located on the Oc3 board. A value of on(1) indicates that an fault condition has been detected (for which a trap will have been issued) and the LED is illuminated. Will be off if no card present.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxOc3FaultStatusLedChange		1.3.6.1.4.1.1141.4.153
generated whenever there is a change in the Fault LED status. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3SerialNumber		1.3.6.1.4.1.1141.2.91.1.1.10
contains the serial number of the Oc3 card. Will contain empty string if card has not been inserted in the slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

hcxOc3SyncClkConfigure		1.3.6.1.4.1.1141.2.91.1.1.11
This attribute allows to configure the Oc3 card as the primary or secondary source for network clock. This attribute is valid only if networkClk is selected in hcxSyncClkConfigure attribute. Only 1 Oc3 Card can be configured as the priSrc and 1 Oc3 Card can be configured as secSrc in the HCX system Default: disable
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), priSrc(2), secSrc(3)

com21HcxOc3PortTable		1.3.6.1.4.1.1141.2.92.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HcxOc3PortEntry

com21HcxOc3PortEntry		1.3.6.1.4.1.1141.2.92.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	HcxOc3PortEntry

hcxOc3PortShelfId		1.3.6.1.4.1.1141.2.92.1.1.1
contains shelf in which this Oc3 port is located.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1

hcxOc3PortSlotId		1.3.6.1.4.1.1141.2.92.1.1.2
contains slot in which this Oc3 port is located.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3PortId		1.3.6.1.4.1.1141.2.92.1.1.3
contains port Id Oc3 port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1

hcxOc3PortPrimServState		1.3.6.1.4.1.1141.2.92.1.1.4
contains primary service state of the Oc3 Unit. This state shall be effected by the hcxOc3PortState attribute.
Status: current	Access: read-only
OBJECT-TYPE
	PrimServiceState

hcxOc3PortPrimStateChange		1.3.6.1.4.1.1141.4.154
This trap is generated whenever a change in the the hcxOc3PortPrimServState occurs. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortSecServState		1.3.6.1.4.1.1141.2.92.1.1.5
contains a string defining the secondary service states of the Oc3 Unit. The substrings supported by the Oc3 Unit shall be: MT - offline, set by hcxOc3, FAULT - hardware failure, TEST - test, UNEQ - unequipped.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

hcxOc3PortSecStateChange		1.3.6.1.4.1.1141.4.155
This trap is generated whenever a change in the the hcxOc3PortSecServState occurs. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3MaxBandwidth		1.3.6.1.4.1.1141.2.92.1.1.6
This attribute defines the maximum output payload bandwidth associated with the Oc3 port. Defined in thousands of bps. From 0 to 22222. This value shall be checked by the CC which shall ensure that the aggregate of the hcxOc3MaxBandwidth and hcxEtherMaxBandwidth attributes for each of the Oc3 and Ethernet ports does not exceed the system maximum. If Voice Channels are configured on this Port, and if Voice channels are active, Ondemand Data bandwidth will get squeezed if Voice Channels are active. Default: 7000
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..22222

hcxOc3AggrDnStrmCbrRate		1.3.6.1.4.1.1141.2.92.1.1.7
This attribute specifies the aggregate of all ComPort downstream CBR rates configured on the Oc3 port This includes both acquired and unacquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3AggrDnStrmPcrRate		1.3.6.1.4.1.1141.2.92.1.1.8
This attribute specifies the aggregate of all ComPort downstream PCR rates configured on the Oc3 port This includes both acquired and unacquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3AggrUpStrmCbrRate		1.3.6.1.4.1.1141.2.92.1.1.9
This attribute specifies the aggregate of all ComPort upstream CBR rates configured on the Oc3 port This includes both acquired and unacquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3AggrUpStrmMinRate		1.3.6.1.4.1.1141.2.92.1.1.10
This attribute specifies the aggregate of all ComPort upstream minimum PCR rates on the Oc3 port This includes both acquired and unacquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3AggrUpStrmMaxRate		1.3.6.1.4.1.1141.2.92.1.1.11
This attribute specifies the aggregate of all ComPort upstream maximum cell rates on the Oc3 port This includes both acquired and unacquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3AgeTime		1.3.6.1.4.1.1141.2.92.1.1.12
This attribute defines, in seconds, the aging time for non-accessed entries in the Bridge mapping table. The default shall be 300secs. If this set to 0, then aging is disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hcxOc3PortConfigState		1.3.6.1.4.1.1141.2.92.1.1.13
The Oc3 Port State is an active-value. The Oc3 port will default to offline, in which case no traffic shall be passed. Default offline.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	offline(2000), online(2001), test(2002)

hcxOc3PortRestartAction		1.3.6.1.4.1.1141.2.92.1.1.14
The Oc3 Port Restart Action is an active-value. The setting of this attribute to restart(2) causes the Oc3 port to reset and download a new image.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nil(1), restart(2)

hcxOc3PortDiagTestAction		1.3.6.1.4.1.1141.2.92.1.1.15
This attribute is used to invoke the internal Oc3 card diagnostic test. In order to activate this test, the card must be placed in the test state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nil(1), execute(2)

hcxOc3PortDiagTestComplete		1.3.6.1.4.1.1141.4.156
This notification is generated whenever the Oc3 port internal diagnostic tests are completed. Event only, no clear. Only severity allowed is WARNING.
Status: current	Access: read-write
NOTIFICATION-TYPE

hcxOc3PortDiagTestResult		1.3.6.1.4.1.1141.2.92.1.1.16
This attribute contains the result of the last Oc3 port diagnostic test.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inprogress(1), success(2), failure(3), invalidState(4)

hcxOc3OperationFailure		1.3.6.1.4.1.1141.4.157
This notification is generated by the CC whenever an Oc3 port fails to respond correctly to a request. This failure could indicate either a resource problem or software failure. Note that if an Oc3 card failures to respond completely to a CC request, then a hcxInsertChange trap shall be generated. This is an event without a corresponding clear. Only severity allowed is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortLOSLed		1.3.6.1.4.1.1141.2.92.1.1.17
The OC3 Loss Of Signal LED indicates whether a Loss of Signal is present on the WAN side of the OC3 port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxOc3PortLOSLedChange		1.3.6.1.4.1.1141.4.158
generated whenever there is a change in the LOS LED status. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3AggrActDnStrmCbrRate		1.3.6.1.4.1.1141.2.92.1.1.18
This attribute specifies the aggregate of all ComPort downstream CBR rates active on the Oc3 port (VLAN). This includes only acquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3AggrActDnStrmPcrRate		1.3.6.1.4.1.1141.2.92.1.1.19
This attribute specifies the aggregate of all ComPort downstream PCR rates active on the Oc3 port (VLAN). This includes only acquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3AggrActUpStrmCbrRate		1.3.6.1.4.1.1141.2.92.1.1.20
This attribute specifies the aggregate of all ComPort upstream CBR rates active on the Oc3 port (VLAN). This includes only acquired ComPorts. Defined in bits per second.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3AggrActUpStrmMinRate		1.3.6.1.4.1.1141.2.92.1.1.21
This attribute specifies the aggregate of all ComPort upstream minimum PCR rates active on the Oc3 port (VLAN). This includes only acquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3AggrActUpStrmMaxRate		1.3.6.1.4.1.1141.2.92.1.1.22
This attribute specifies the aggregate of all ComPort upstream maximum cell rates active on the Oc3 port (VLAN). This includes only acquired ComPorts. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3PortIpAddr		1.3.6.1.4.1.1141.2.92.1.1.23
IP Address associated with this ethernet port. This is a future item for telephone return support.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

hcxOc3PortIpMask		1.3.6.1.4.1.1141.2.92.1.1.24
IP mask associated with port. Default is ff.ff.ff.ff. This is a future item for telephone return support.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

hcxOc3PortMacAddr		1.3.6.1.4.1.1141.2.92.1.1.25
MAC address associated with port.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

hcxOc3Port1483EncapEnbl		1.3.6.1.4.1.1141.2.92.1.1.26
This attribute is used to Enable/Disable 1483 Encapsulation on the Oc3Port. If enabled, then all Ethernet packets received by the Oc3Port should be 1483 Encapsulated and all Ethernet packets transmitted by the Oc3Port will be 1483 Encapsulated. Default: enable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hcxOc3PortSectionLOS		1.3.6.1.4.1.1141.2.92.1.1.27
This attribute indicates whether Section Loss of Signal is present at the OC3 Port. Default: off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxOc3PortSectionLOSDetected		1.3.6.1.4.1.1141.4.159
generated whenever Loss of Signal is detected at the OC3 Port. Alarm Severity: MAJOR
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortSectionLOSClear		1.3.6.1.4.1.1141.4.160
generated whenever Loss of Signal is Cleared at the OC3 Port. Alarm Severity: CLEAR
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortSectionLOF		1.3.6.1.4.1.1141.2.92.1.1.28
This attribute indicates whether Section Loss of Frame is present at the OC3 Port. Default: off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxOc3PortSectionLOFDetected		1.3.6.1.4.1.1141.4.161
generated whenever Loss of Frame is detected at the OC3 Port. Alarm Severity: MAJOR
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortSectionLOFClear		1.3.6.1.4.1.1141.4.162
generated whenever Loss of Frame is cleared at the OC3 Port. Alarm Severity: CLEAR
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortLineAIS		1.3.6.1.4.1.1141.2.92.1.1.29
This attribute indicates whether Line Alarm Indication Signal is detected by the OC3 Port Default: off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxOc3PortLineAISDetected		1.3.6.1.4.1.1141.4.163
generated whenever AIS is detected at the OC3 Port. Alarm Severity: MAJOR
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortLineAISClear		1.3.6.1.4.1.1141.4.164
generated whenever AIS is cleared at the OC3 Port. Alarm Severity: CLEAR
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortLineRDI		1.3.6.1.4.1.1141.2.92.1.1.30
This attribute indicates whether Line Remote Defect Indication is detected by the OC3 Port Default: off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxOc3PortLineRDIDetected		1.3.6.1.4.1.1141.4.165
generated whenever Line Remote Defect Indication is detected at the OC3 Port. Alarm Severity: MAJOR
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortLineRDIClear		1.3.6.1.4.1.1141.4.166
generated whenever Line Remote Defect Indication is cleared at the OC3 Port. Alarm Severity: CLEAR
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortPathRDI		1.3.6.1.4.1.1141.2.92.1.1.31
This attribute indicates whether Path Remote Defect Indication is detected by the OC3 Port Default: off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxOc3PortPathRDIDetected		1.3.6.1.4.1.1141.4.167
generated whenever Path Remote Defect Indication is detected at the OC3 Port. Alarm Severity: MAJOR
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortPathRDIClear		1.3.6.1.4.1.1141.4.168
generated whenever Path Remote Defect Indication is cleared at the OC3 Port. Alarm Severity: CLEAR
Status: current	Access: read-only
NOTIFICATION-TYPE

hcxOc3PortAggrVoiceRate		1.3.6.1.4.1.1141.2.92.1.1.32
This attribute specifies the aggregate Rate of all Voice Channels configured on this Port. A voice channel is considered configured on this Port if: a ComPort is configured with Voice Channel and the ComPort is configured on a Vlan which is on this Port. The rate specified here includes both acquired and unacquired ComPorts and is the same in both Upstream and Downstream Direction. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3PortAggrActVoiceRate		1.3.6.1.4.1.1141.2.92.1.1.33
This attribute specifies the aggregate Rate of all Voice Channels Active on this Port. A voice channel is considered Active on this Port if: a ComPort is configured with Voice Channel and the ComPort is configured on a Vlan which is on this Port and the Comport is acquired and the Comport has a Voice Channel Active. The rate specified here is the same in both Upstream and Downstream Direction. Defined in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3PortLOFLed		1.3.6.1.4.1.1141.2.92.1.1.34
The OC3 Loss Of Frame LED indicates whether a Loss of Frame is present on the WAN side of the OC3 port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

hcxOc3PortLOFLedChange		1.3.6.1.4.1.1141.4.169
generated whenever there is a change in the LOF LED status. This an event with no clear condition. Only severity is WARNING.
Status: current	Access: read-only
NOTIFICATION-TYPE

com21HcxOc3VccTable		1.3.6.1.4.1.1141.2.93.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HcxOc3VccEntry

com21HcxOc3VccEntry		1.3.6.1.4.1.1141.2.93.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	HcxOc3VccEntry

hcxOc3VccShelfId		1.3.6.1.4.1.1141.2.93.1.1.1
Specifies the Shelf where this Entry exists.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3VccSlotId		1.3.6.1.4.1.1141.2.93.1.1.2
Specifies the Slot where this Entry exists.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3VccPortId		1.3.6.1.4.1.1141.2.93.1.1.3
Specifies the Port where this Entry exists.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3VccVpi		1.3.6.1.4.1.1141.2.93.1.1.4
Specifies the Vpi where this Entry exists.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3VccVci		1.3.6.1.4.1.1141.2.93.1.1.5
Specifies the Vci where this Entry exists.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3VccType		1.3.6.1.4.1.1141.2.93.1.1.6
Specifies whether this VCC is used to transport data or voice.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	data(1), voice(2)

com21HcxOc3StatsTable		1.3.6.1.4.1.1141.2.94.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HcxOc3StatsEntry

com21HcxOc3StatsEntry		1.3.6.1.4.1.1141.2.94.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	HcxOc3StatsEntry

hcxOc3StatsShelfId		1.3.6.1.4.1.1141.2.94.1.1.1
Specifies the Shelf where this Entry exists.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsSlotId		1.3.6.1.4.1.1141.2.94.1.1.2
Specifies the Slot where this Entry exists.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsPortId		1.3.6.1.4.1.1141.2.94.1.1.3
Specifies the Port where this Entry exists.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsCurrSectionBIPErr		1.3.6.1.4.1.1141.2.94.1.1.4
This attributes displays the number of Section Byte Interleaved Parity Errors reported by the OC3 Port in the current 15-minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsCurrLineBIPErr		1.3.6.1.4.1.1141.2.94.1.1.5
This attributes displays the number of Line Byte Interleaved Parity Errors reported by the OC3 Port in the current 15-minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsCurrPathBIPErr		1.3.6.1.4.1.1141.2.94.1.1.6
This attributes displays the number of Path Byte Interleaved Parity Errors reported by the OC3 Port in the current 15-minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsCurrLineFEndBlockErr		1.3.6.1.4.1.1141.2.94.1.1.7
This attributes displays the number of Far End Line Block Errors reported by the OC3 Port in the current 15-minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsCurrPathFEndBlockErr		1.3.6.1.4.1.1141.2.94.1.1.8
This attributes displays the number of Far End Path Block Errors reported by the OC3 Port in the current 15-minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsPrevSectionBIPErr		1.3.6.1.4.1.1141.2.94.1.1.9
This attributes displays the number of Section Byte Interleaved Parity Errors reported by the OC3 Port in the current 15-minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsPrevLineBIPErr		1.3.6.1.4.1.1141.2.94.1.1.10
This attributes displays the number of Line Byte Interleaved Parity Errors reported by the OC3 Port in the current 15-minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsPrevPathBIPErr		1.3.6.1.4.1.1141.2.94.1.1.11
This attributes displays the number of Path Byte Interleaved Parity Errors reported by the OC3 Port in the current 15-minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsPrevLineFEndBlockErr		1.3.6.1.4.1.1141.2.94.1.1.12
This attributes displays the number of Far End Line Block Errors reported by the OC3 Port in the current 15-minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsPrevPathFEndBlockErr		1.3.6.1.4.1.1141.2.94.1.1.13
This attributes displays the number of Far End Path Block Errors reported by the OC3 Port in the current 15-minute period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hcxOc3StatsClear		1.3.6.1.4.1.1141.2.94.1.1.14
This attribute is used to clear the all OC3 Stats statistics counters in this group. This operation is only possible if the hcxStatsControl attribute is set to wrapCurr.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nil(1), clear(2)