COM21-HCXRX-MIB

File: COM21-HCXRX-MIB.mib (86015 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC COM21-HCX-MIB
COM21-HCXALM-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Integer32 IpAddress Gauge32
DisplayString MacAddress com21
com21Hcx com21Traps hcxAlmSeverity
hcxEventLogTime

Defined Types

UpstrmFreqKhz  
INTEGER 5000..40000    

PrimServiceState  
INTEGER is(1), oos(2)    

RfAnalysisdBmv  
INTEGER -58..-5    

HcxUpstrmUnitEntry  
SEQUENCE    
  hcxUpstreamShelfId INTEGER
  hcxUpstreamSlotId Integer32
  hcxUpstreamHardwareVersion DisplayString
  hcxUpstreamBootVersion DisplayString
  hcxUpstreamUnitPrimServState PrimServiceState
  hcxUpstreamUnitSecServState DisplayString
  hcxUpstreamUnitConfigState INTEGER
  hcxUpstreamUnitRestartAction INTEGER
  hcxUpstreamGroupId INTEGER
  hcxAcquisitionEnable INTEGER
  hcxUpDiagTestAction INTEGER
  hcxUpDiagTestResult INTEGER
  hcxUpTestStatusLed INTEGER
  hcxUpFaultStatusLed INTEGER
  hcxUpstreamSerialNumber DisplayString

HcxUpstrmPortEntry  
SEQUENCE    
  hcxUpstrmPortShelfId INTEGER
  hcxUpstrmPortSlotId Integer32
  hcxUpstreamPortId Integer32
  hcxRecvFrequency UpstrmFreqKhz
  hcxRecvPower INTEGER
  hcxUpstrmAggrStuCbrRate Integer32
  hcxUpstrmAggrStuMinRate Integer32
  hcxUpstrmAggrStuMaxRate Integer32
  hcxUpstrmFreqHopping INTEGER
  hcxUpstrmAltFreqA INTEGER
  hcxUpstrmAltFreqB INTEGER
  hcxUpstrmActiveFreq UpstrmFreqKhz
  hcxUpstrmRpmControl INTEGER
  hcxUpstrmRpmPrimServState PrimServiceState
  hcxUpstrmRpmSecServState DisplayString
  hcxUpstrmRpmConnType INTEGER
  hcxUpstrmAggrStuVoiceRate Integer32

HcxUpstrmStatsEntry  
SEQUENCE    
  hcxStatsUpstreamShelfId INTEGER
  hcxStatsUpstreamSlotId Integer32
  hcxStatsUpstreamPortId Integer32
  hcxPortCurrMinRxCells Gauge32
  hcxPortCurrMinRxNullCells Gauge32
  hcxPortCurrMinUncorrFecHecCells Gauge32
  hcxPortCurrMinCorrectedFec Gauge32
  hcxPortCurrMinOverSubPeriods Gauge32
  hcxPortPrevMinRxCells Gauge32
  hcxPortPrevMinRxNullCells Gauge32
  hcxPortPrevMinUncorrFecHecCells Gauge32
  hcxPortPrevMinCorrectedFec Gauge32
  hcxPortPrevMinOverSubPeriods Gauge32
  hcxPortUpstreamUtil INTEGER
  hcxPortCurrMeanNoise Integer32
  hcxPortPrevMeanNoise Integer32
  hcxPortCorrFecRatioThres INTEGER
  hcxPortCellErrRatioThres INTEGER
  hcxPortRatioThresPeriod INTEGER
  hcxPortMinErrRatioCells INTEGER
  hcxPortCnrThres INTEGER
  hcxPortCurrMinNoise Integer32
  hcxPortCurrMaxNoise Integer32
  hcxPortPrevMinNoise Integer32
  hcxPortPrevMaxNoise Integer32
  hcxPortRealTimeMeanNoise Integer32
  hcxPortRealTimeMinNoise Integer32
  hcxPortRealTimeMaxNoise Integer32
  hcxPortClearStats INTEGER

HcxVciStatsEntry  
SEQUENCE    
  hcxStuStatsMacAddr MacAddress
  hcxStatsCurrMinRxCells Gauge32
  hcxStatsCurrMinRxNullCells Gauge32
  hcxStatsCurrMinUncorFecHec Gauge32
  hcxStatsCurrMinUncorFecThres Integer32
  hcxStatsCurrMinCorrectedFec Gauge32
  hcxStatsCurrMinCorFecThres Integer32
  hcxStatsPrevMinRxCells Gauge32
  hcxStatsPrevMinRxNullCells Gauge32
  hcxStatsPrevMinUncorFecHec Gauge32
  hcxStatsPrevMinCorrectedFec Gauge32
  hcxStatsCurrMinMeanSignal Integer32
  hcxStatsPrevMinMeanSignal Integer32
  hcxStatsClearStats INTEGER

HcxRpmIPortEntry  
SEQUENCE    
  hcxRpmIPortShelfId INTEGER
  hcxRpmIPortSlotId Integer32
  hcxRpmRxPortId Integer32
  hcxRpmIPortId INTEGER
  hcxRpmIPortRecvPower INTEGER
  hcxRpmIPortConfigState INTEGER
  hcxRpmIPortContSchedType INTEGER

HcxRpmStatsEntry  
SEQUENCE    
  hcxStatsRpmShelfId INTEGER
  hcxStatsRpmSlotId Integer32
  hcxStatsRxPortId Integer32
  hcxStatsRpmIPortId INTEGER
  hcxRpmCurrMinRxCells Gauge32
  hcxRpmCurrMinRxNullCells Gauge32
  hcxRpmCurrMinUncorFecHecCells Gauge32
  hcxRpmCurrMinCorrectedFec Gauge32
  hcxRpmCurrMeanNoise Integer32
  hcxRpmCurrMinNoise Integer32
  hcxRpmCurrMaxNoise Integer32
  hcxRpmRealTimeMeanNoise Integer32
  hcxRpmRealTimeMinNoise Integer32
  hcxRpmRealTimeMaxNoise Integer32
  hcxRpmPrevMinRxCells Gauge32
  hcxRpmPrevMinRxNullCells Gauge32
  hcxRpmPrevMinUncorFecHecCells Gauge32
  hcxRpmPrevMinCorrectedFec Gauge32
  hcxRpmPrevMeanNoise Integer32
  hcxRpmPrevMinNoise Integer32
  hcxRpmPrevMaxNoise Integer32
  hcxRpmCorrFecRatioThres INTEGER
  hcxRpmCellErrRatioThres INTEGER
  hcxRpmRatioThresPeriod INTEGER
  hcxRpmMinErrRatioCells INTEGER
  hcxRpmCnrThres INTEGER
  hcxRpmClearStats INTEGER

HcxRfAnalysisEntry  
SEQUENCE    
  hcxRfAnalysisShelfId INTEGER
  hcxRfAnalysisSlotId Integer32
  hcxRfAnalysisPortId Integer32
  hcxRfAnalysisRpmPortId INTEGER
  hcxRfAnalysisControl INTEGER
  hcxRfAnalysisPoint1 INTEGER
  hcxRfAnalysisPoint2 INTEGER
  hcxRfAnalysisPoint3 INTEGER
  hcxRfAnalysisPoint4 INTEGER
  hcxRfAnalysisBin1Count Gauge32
  hcxRfAnalysisBin2Count Gauge32
  hcxRfAnalysisBin3Count Gauge32
  hcxRfAnalysisClearCount INTEGER

Defined Values

com21HcxRx 1.3.6.1.4.1.1141.2.30
This is the Com21 ComController RX card MIB. COM21 Part# 005-0025-00
MODULE-IDENTITY    

com21HcxUpstrmPortGroup 1.3.6.1.4.1.1141.2.31
OBJECT IDENTIFIER    

com21HcxUpstrmStatsGroup 1.3.6.1.4.1.1141.2.32
OBJECT IDENTIFIER    

com21HcxUpstrmUnitGroup 1.3.6.1.4.1.1141.2.33
OBJECT IDENTIFIER    

com21HcxVciStatsGroup 1.3.6.1.4.1.1141.2.34
OBJECT IDENTIFIER    

com21HcxRpmIPortGroup 1.3.6.1.4.1.1141.2.35
OBJECT IDENTIFIER    

com21HcxRpmStatsGroup 1.3.6.1.4.1.1141.2.36
OBJECT IDENTIFIER    

com21HcxRfAnalysisGroup 1.3.6.1.4.1.1141.2.37
OBJECT IDENTIFIER    

com21HcxUpstrmUnitTable 1.3.6.1.4.1.1141.2.33.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HcxUpstrmUnitEntry

com21HcxUpstrmUnitEntry 1.3.6.1.4.1.1141.2.33.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  HcxUpstrmUnitEntry  

hcxUpstreamShelfId 1.3.6.1.4.1.1141.2.33.1.1.1
contains upstream shelf id.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

hcxUpstreamSlotId 1.3.6.1.4.1.1141.2.33.1.1.2
contains upstream unit id. This is the slot number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxUpstreamHardwareVersion 1.3.6.1.4.1.1141.2.33.1.1.3
contains the hardware version of the RX card. Will be empty if card not present.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(16)  

hcxUpstreamBootVersion 1.3.6.1.4.1.1141.2.33.1.1.4
contains the version of the RX card boot ROM. This will be an empty string if card is missing.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(16)  

hcxUpstreamUnitPrimServState 1.3.6.1.4.1.1141.2.33.1.1.5
contains primary service state of the Upstream Unit.
Status: current Access: read-only
OBJECT-TYPE    
  PrimServiceState  

hcxUpstreamUnitPrimStateChange 1.3.6.1.4.1.1141.4.30
Generated whenever a the hcxUpstreamUnitPrimServState changes in value. This an event with no clear condition. Only severity is WARNING.
Status: current Access: read-only
NOTIFICATION-TYPE    

hcxUpstreamUnitSecServState 1.3.6.1.4.1.1141.2.33.1.1.6
contains a string defining the secondary service states of the Upstream Unit. The substrings supported by the Upstream Unit shall be: TEST - in test, as set by hcxUpstreamUnitConfigState, MT - offline, again set by hcxUpstreamUnitConfigState, FAULT - hardware failure, UNEQ - unequipped.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(16)  

hcxUpstreamUnitSecStateChange 1.3.6.1.4.1.1141.4.31
Generated whenever a the hcxUpstreamUnitSecServState changes in value. This an event with no clear condition. Only severity is WARNING.
Status: current Access: read-only
NOTIFICATION-TYPE    

hcxUpstreamUnitConfigState 1.3.6.1.4.1.1141.2.33.1.1.7
The Upstream Unit State is an active-value. Offline will disable the RF and all other cell forwarding. Online enables RF and performs all traffic and scheduling functions. Test will also place the card offline but shall allow a diagnostic test. Maintenance keeps RF alive but RX performs no scheduling. Note that RX card will not enter the maintenance state if there are any authorized ComPorts. It is the responsibility of the CC to hop any ComPorts prior to entering this state. Offline is default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER offline(2000), online(2001), test(2002)  

hcxUpstreamUnitRestartAction 1.3.6.1.4.1.1141.2.33.1.1.8
The RX Unit Restart Action is an active-value. The setting of this attribute to restart(2) causes the RX card to reset and download a new image.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nil(1), restart(2)  

hcxUpstreamGroupId 1.3.6.1.4.1.1141.2.33.1.1.9
The Upstream group id defines the receiver group to which this RF Receiver belongs. The shall ensure that the group contains a single RF Receiver card operating as an ComPort acquirer. Default is group 1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..12  

hcxAcquisitionEnable 1.3.6.1.4.1.1141.2.33.1.1.10
Used to select an RF Receiver for acquisition. The ComController shall ensure that only one RX card in a receiver group is selected for acquisition.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxUpDiagTestAction 1.3.6.1.4.1.1141.2.33.1.1.11
This attribute is used to invoke the internal RX diagnostic test. In order to activate this test, the card must be placed in the test state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nil(1), execute(2)  

hcxUpDiagTestComplete 1.3.6.1.4.1.1141.4.32
This notification is generated whenever the RX internal diagnostic tests are completed. This an event with no clear condition. Only severity is WARNING.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxUpDiagTestResult 1.3.6.1.4.1.1141.2.33.1.1.12
This attribute contains the result of the last RX diagnostic test.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inprogress(1), success(2), failure(3), invalidState(4)  

hcxUpTestStatusLed 1.3.6.1.4.1.1141.2.33.1.1.13
The RX Test Status LED is a read-only attribute which describes the condition of the RX Test Status light emitting diode located on the RX board. A value of on(1) indicates that a service effecting test is in progress and that the LED is illuminated. off if no card present.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

hcxUpTestStatusLedChange 1.3.6.1.4.1.1141.4.33
generated whenever there is a change in test LED status. This an event with no clear condition. Only severity is WARNING.
Status: current Access: read-only
NOTIFICATION-TYPE    

hcxUpFaultStatusLed 1.3.6.1.4.1.1141.2.33.1.1.14
The RX Fault Status LED is a read-only attribute which describes the condition of the RX Fault Status light emitting diode located on the RX board. A value of on(1) indicates that an fault condition has been detected (for which a trap will have been issued) and the LED is illuminated. off if no card present.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

hcxUpFaultStatusLedChange 1.3.6.1.4.1.1141.4.34
generated whenever there is a change in the Fault LED status. This an event with no clear condition. Only severity is WARNING.
Status: current Access: read-only
NOTIFICATION-TYPE    

hcxUpOperationFailure 1.3.6.1.4.1.1141.4.35
This notification is generated by the CC whenever an RX card fails to respond correctly to a request. This failure could indicate either a resource problem or software failure. Note that if an RX card failures to respond completely to a CC request, then a hcxInsertChange trap shall be generated. This an event with no clear condition. Only severity is WARNING.
Status: current Access: read-only
NOTIFICATION-TYPE    

hcxUpstreamSerialNumber 1.3.6.1.4.1.1141.2.33.1.1.15
contains the serial number of the RX card. This will be an empty string if card is missing.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(16)  

com21HcxUpstrmPortTable 1.3.6.1.4.1.1141.2.31.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HcxUpstrmPortEntry

com21HcxUpstrmPortEntry 1.3.6.1.4.1.1141.2.31.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  HcxUpstrmPortEntry  

hcxUpstrmPortShelfId 1.3.6.1.4.1.1141.2.31.1.1.1
contains upstream shelf id containing the RX card.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

hcxUpstrmPortSlotId 1.3.6.1.4.1.1141.2.31.1.1.2
contains upstream slot id containing the port. Presently there is one port per card.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxUpstreamPortId 1.3.6.1.4.1.1141.2.31.1.1.3
Contains the id for the upstream port. Presently should be one only.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRecvFrequency 1.3.6.1.4.1.1141.2.31.1.1.4
Contains the receive frequency of the RF board in KHz. Note that any change to this frequency shall result in temporary loss of service for the ComPorts as the RX needs to issue a frquency change message to each ComPort in turn. Also note that the CC shall check for frequency overlap with other RX cards within the group - the RX channels can be no closer than 1.8Mhz. With the advent of frequency hopping this attribute defines the primary frequency. Minimum step size is 50. i.e. 50000hz. Default is 0.
Status: current Access: read-write
OBJECT-TYPE    
  UpstrmFreqKhz  

hcxRecvPower 1.3.6.1.4.1.1141.2.31.1.1.5
Contains the receiver power level in dBmv. Default is 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -15..15  

hcxUpstrmAggrStuCbrRate 1.3.6.1.4.1.1141.2.31.1.1.6
This attribute defines the aggregate of all ComPort upstream CBR rates on the RX port. Defined in Kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxUpstrmAggrStuMinRate 1.3.6.1.4.1.1141.2.31.1.1.7
This attribute defines the aggregate of all ComPort upstream Minimum rates on the RX port. Defined in Kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxUpstrmAggrStuMaxRate 1.3.6.1.4.1.1141.2.31.1.1.8
This attribute defines the aggregate of all ComPort upstream Maximum rates on the RX port. Defined in Kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRxFreqHop 1.3.6.1.4.1.1141.4.82
This trap is generated when an RX port frequency is hopped due to errors. The hcxUpstrmActiveFreq varbind indicates the new frequency. Severity is WARNING.
Status: current Access: read-only
NOTIFICATION-TYPE    

hcxUpstrmFreqHopping 1.3.6.1.4.1.1141.2.31.1.1.9
This attribute controls whether an RX port is protected by automatic frequency hopping. If this attribute is transitioned from on -> off then the RX port shall return to the primary frequency. This method can be used to force an RX port to a specific frequency if a hop away from the primary freq had previously occurred. Default will be on.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

hcxUpstrmAltFreqA 1.3.6.1.4.1.1141.2.31.1.1.10
Contains the first alternate frequency for this RX port. This need NOT be unique. i.e. other RX ports within the receiver group can also share the same alternate frequencies. Valid values are 0 or 5000-40000KHz. 0 indicates no alternate frequency. If this frequency was being used by the receiver port and is set to 0 then the port shall revert back to the primary frequency. Minimum step size is 50. i.e. 50000hz. Default is 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..40000  

hcxUpstrmAltFreqB 1.3.6.1.4.1.1141.2.31.1.1.11
Contains the second alternate frequency for this RX port. Same restrictions and defaults as for hcxUpstrmAltFreqA.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..40000  

hcxUpstrmActiveFreq 1.3.6.1.4.1.1141.2.31.1.1.12
Contains the presently active frequency. i.e. primary, alternate A or alternate B. Upon initial deployment of the system this frequency will always match the primary frequency. Upon reboot, the RX port shall always return to this frequency.
Status: current Access: read-only
OBJECT-TYPE    
  UpstrmFreqKhz  

hcxUpstrmRpmControl 1.3.6.1.4.1.1141.2.31.1.1.13
Defines RPM control. This attribute is only applicable in the case of an RXM card. For the RX card this attribute will be read-only with a value of notSupported. If the RPM is present then the control shall be validated against the physical configuration. If an attempt is made to place the RPM in 8 port mode but it is physically configured for 4 port, then an error response shall be return. Default for RxM is enable8Port. Option notSupported is unavailable for RxM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(1), enable4Port(2), enable8Port(3)  

hcxRpmInvalidPhyConfig 1.3.6.1.4.1.1141.4.87
this trap is generated whenever the actual RPM configuration does not match that defined by the hcxUpstrmRpmControl attribute above. Default severity is MINOR.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxRpmInvalidConfClear 1.3.6.1.4.1.1141.4.88
this trap is generated once the actual and configured RPM configuration match. Severity is CLEARED.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxRpmTimingFault 1.3.6.1.4.1.1141.4.89
this trap is generated whenever an RPM timing problem is detected. Default severity is MINOR.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxRpmTimingFaultClear 1.3.6.1.4.1.1141.4.130
this trap is generated once a previously detected RPM timing problem is cleared. Severity is CLEARED.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxRpmLinkError 1.3.6.1.4.1.1141.4.131
this trap is generated whenever the link between the RPM and RxM is detected as down or in error. Default severity is MINOR.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxRpmLinkErrClear 1.3.6.1.4.1.1141.4.132
this trap is generated once a previously reported RPM link error is cleared. Severity is CLEARED.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxUpstrmRpmPrimServState 1.3.6.1.4.1.1141.2.31.1.1.14
contains primary service state of the RPM.
Status: current Access: read-only
OBJECT-TYPE    
  PrimServiceState  

hcxUpstrmRpmPrimStateChange 1.3.6.1.4.1.1141.4.133
Generated whenever a the hcxUpstrmRpmPrimServState changes in value. This an event with no clear condition. Only severity is WARNING.
Status: current Access: read-only
NOTIFICATION-TYPE    

hcxUpstrmRpmSecServState 1.3.6.1.4.1.1141.2.31.1.1.15
contains a string defining the secondary service states of the RPM. The substrings supported by the RPM shall be: UNEQ - not present, CONF - invalid configuration, LINK - link fault, TIME - timing fault.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(16)  

hcxUpstrmRpmConnType 1.3.6.1.4.1.1141.2.31.1.1.16
contains management connection type to the RPM device. Note that if the RxM is in slave mode, then the state information defined by the attributes above shall not be applicable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unconnected(1), master(2), slave(3)  

hcxUpstrmAggrStuVoiceRate 1.3.6.1.4.1.1141.2.31.1.1.17
This attribute defines the aggregate of all ComPort upstream voice rates on the RX port. Defined in Kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

com21HcxUpstrmStatsTable 1.3.6.1.4.1.1141.2.32.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HcxUpstrmStatsEntry

com21HcxUpstrmStatsEntry 1.3.6.1.4.1.1141.2.32.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  HcxUpstrmStatsEntry  

hcxStatsUpstreamShelfId 1.3.6.1.4.1.1141.2.32.1.1.1
Contains the id for the shelf in which the associated RX card is located.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

hcxStatsUpstreamSlotId 1.3.6.1.4.1.1141.2.32.1.1.2
Contains the id for the upstream slot.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxStatsUpstreamPortId 1.3.6.1.4.1.1141.2.32.1.1.3
Contains the id for the upstream port. Between 1 and 12
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxPortCurrMinRxCells 1.3.6.1.4.1.1141.2.32.1.1.4
Represents the number of cells received in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxPortCurrMinRxNullCells 1.3.6.1.4.1.1141.2.32.1.1.5
Represents the number of null cells received in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxPortCurrMinUncorrFecHecCells 1.3.6.1.4.1.1141.2.32.1.1.6
Represents the number of received cells with either uncorrectable FEC or HEC errors in current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxPortCurrMinCorrectedFec 1.3.6.1.4.1.1141.2.32.1.1.8
Represents the number of corrected FEC errors in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxPortCurrMinOverSubPeriods 1.3.6.1.4.1.1141.2.32.1.1.9
Represents the number of 512 cell slot scheduling periods that were actively oversubscribed in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxPortPrevMinRxCells 1.3.6.1.4.1.1141.2.32.1.1.10
Represents the number of cells received in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxPortPrevMinRxNullCells 1.3.6.1.4.1.1141.2.32.1.1.11
Represents the number of cells received in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxPortPrevMinUncorrFecHecCells 1.3.6.1.4.1.1141.2.32.1.1.12
Represents the number of received cells with either uncorrectable FEC or HEC errors in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxPortPrevMinCorrectedFec 1.3.6.1.4.1.1141.2.32.1.1.14
Represents the number of corrected FEC errors in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxPortPrevMinOverSubPeriods 1.3.6.1.4.1.1141.2.32.1.1.15
Represents the number of 512 cell slot scheduling periods that were actively oversubscribed in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxPortUpstreamUtil 1.3.6.1.4.1.1141.2.32.1.1.16
Represents the percentage of utilization on all slots of the upstream channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

hcxPortCurrMeanNoise 1.3.6.1.4.1.1141.2.32.1.1.17
This attribute defines the mean noise level in dBmv sampled by the RX card in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxPortPrevMeanNoise 1.3.6.1.4.1.1141.2.32.1.1.18
This attribute defines the mean noise level in dBmv sampled by the RX card in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxPortCorrFecRatioThres 1.3.6.1.4.1.1141.2.32.1.1.19
This attribute defines a threshold point at which a hop of the receive channel frequency shall take place. The threshold is defined as the percentage of corrected FEC errored cells to good cells. The RX card shall calculate this percentage over a one second period, and the threshold must be crossed for the period defined by the hcxPortRatioThresPeriod attribute before a trap is generated. In addition the cells received within the second must be greater than that defined by hcxPortMinErrRatioCells. A value of 0 disables the threshold. Default is 20. If this RX port is connected to an RPM then this threshold is not valid.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

hcxCorrFecRatioThres 1.3.6.1.4.1.1141.4.80
Severity is WARNING.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxPortCellErrRatioThres 1.3.6.1.4.1.1141.2.32.1.1.20
This attribute defines a threshold point at which a hop of the receive channel frequency shall take place. The threshold is defined as the percentage of FEC/HEC errored cells to good cells. The RX card shall calculate this percentage over a one second period, and the threshold must be crossed for the period defined by the hcxPortRatioThresPeriod attribute before a trap is generated. In addition the cells received within one second must be greater than that defined by hcxPortMinErrRatioCells. A value of 0 disables the threshold. Default is 10. If this RX port is connected to an RPM then this threshold is not valid.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

hcxCellErrRatioThres 1.3.6.1.4.1.1141.4.81
Severity is WARNING.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxPortRatioThresPeriod 1.3.6.1.4.1.1141.2.32.1.1.21
This attribute defines the integration period for the error ratio thresholds. This attribute defines the number of seconds over which the threshold is contiguously exceeded before a trap is generated. 0 disables the thresholds. Default is 5.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..900  

hcxPortMinErrRatioCells 1.3.6.1.4.1.1141.2.32.1.1.22
This attribute defines the minimum number of cells that should be received per second in order to allow the Error and Corrected Cell Thresholds to cause a frequency hop. Default is 50.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..2500  

hcxPortCnrThres 1.3.6.1.4.1.1141.2.32.1.1.23
Defines the average carrier to noise level, in dB, at which a frequency hop should occur. Note that the data error thresholds define above take precedence - this CNR threshold applies only if the data rate is less than the hcxPortMinErrRatioCells. Default 11dB. If this RX port is connected to an RPM then this threshold is not valid.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 7..16  

hcxCnrThres 1.3.6.1.4.1.1141.4.83
Tbd. Severity is WARNING.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxPortCurrMinNoise 1.3.6.1.4.1.1141.2.32.1.1.24
defines the minimum noise level in dBmv sampled by the RX card in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxPortCurrMaxNoise 1.3.6.1.4.1.1141.2.32.1.1.25
defines the maximum noise level in dBmv sampled by the RX card in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxPortPrevMinNoise 1.3.6.1.4.1.1141.2.32.1.1.26
defines the minimum noise level in dBmv sampled by the RX card in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxPortPrevMaxNoise 1.3.6.1.4.1.1141.2.32.1.1.27
defines the maximum noise level in dBmv sampled by the RX card in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxPortRealTimeMeanNoise 1.3.6.1.4.1.1141.2.32.1.1.28
This attribute provides a realtime mean noise level in dBmv. It is updated every approx 5 seconds and provides a snap shot of the noise conditions on this receiver port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxPortRealTimeMinNoise 1.3.6.1.4.1.1141.2.32.1.1.29
::= { com21HcxUpstrmStatsEntry 29 } This attribute provides a realtime min noise level in dBmv. The attribute is updated every approx 5 seconds and provides the minimum noise level during that period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxPortRealTimeMaxNoise 1.3.6.1.4.1.1141.2.32.1.1.30
This attribute provides a realtime max noise level in dBmv. The attribute is updated every approx 5 seconds and provides the maximum noise level during that period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxPortClearStats 1.3.6.1.4.1.1141.2.32.1.1.31
This attribute is used to clear all RX statistics counters in this group. This operation is only possible if the hcxStatsControl attribute is set to wrapCurr.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nil(1), clear(2)  

com21HcxVciStatsTable 1.3.6.1.4.1.1141.2.34.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HcxVciStatsEntry

com21HcxVciStatsEntry 1.3.6.1.4.1.1141.2.34.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  HcxVciStatsEntry  

hcxStuStatsMacAddr 1.3.6.1.4.1.1141.2.34.1.1.1
Contains IEEE 802 medium access control address of the ComPort device.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

hcxStatsCurrMinRxCells 1.3.6.1.4.1.1141.2.34.1.1.2
Represents the number of cells successfully received in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxStatsCurrMinRxNullCells 1.3.6.1.4.1.1141.2.34.1.1.3
Represents the number of null cells received in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxStatsCurrMinUncorFecHec 1.3.6.1.4.1.1141.2.34.1.1.6
Represents the number of bad cells - HEC/Uncorrectable FEC/ Collisions - reported in cell slots allocated to this ComPort/VCI in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxStatsCurrMinUncorFecThres 1.3.6.1.4.1.1141.2.34.1.1.7
Represents the number of HEC/Uncorrectable FEC error cells received in the present 15minute period that shall cause a threshold trap to be generated. Default is 0 - threshold disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hcxUncorFecHecMinThres 1.3.6.1.4.1.1141.4.37
Severity is WARNING.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxStatsCurrMinCorrectedFec 1.3.6.1.4.1.1141.2.34.1.1.8
Represents the number of corrected FEC errors for this ComPort/VCI in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxStatsCurrMinCorFecThres 1.3.6.1.4.1.1141.2.34.1.1.9
Represents the number of corrected FEC errors in the present 15minute period that shall cause a threshold trap to be generated. Default is 0 - threshold disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hcxCorrectedFecMinThres 1.3.6.1.4.1.1141.4.38
Severity is WARNING.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxStatsPrevMinRxCells 1.3.6.1.4.1.1141.2.34.1.1.10
Represents the number of cells successfully received in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxStatsPrevMinRxNullCells 1.3.6.1.4.1.1141.2.34.1.1.11
Represents the number of null cells received in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxStatsPrevMinUncorFecHec 1.3.6.1.4.1.1141.2.34.1.1.13
Represents the number of bad cells - HEC/Uncorrectable FEC/Collisions - reported in cell slots allocated to this ComPort/VCI in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxStatsPrevMinCorrectedFec 1.3.6.1.4.1.1141.2.34.1.1.14
Represents the number of corrected FEC errors for this ComPort/VCI in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxStatsCurrMinMeanSignal 1.3.6.1.4.1.1141.2.34.1.1.15
This attribute contains the mean signal strength value in dBmv sampled for this ComPort in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxStatsPrevMinMeanSignal 1.3.6.1.4.1.1141.2.34.1.1.16
This attribute contains the mean signal strength value in dBmv sampled for this ComPort in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxStatsClearStats 1.3.6.1.4.1.1141.2.34.1.1.17
This attribute is used to clear all RX ComPort statistics counters in this group. This operation is only possible if the hcxStatsControl attribute is set to wrapCurr.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nil(1), clear(2)  

com21HcxRpmIPortTable 1.3.6.1.4.1.1141.2.35.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HcxRpmIPortEntry

com21HcxRpmIPortEntry 1.3.6.1.4.1.1141.2.35.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  HcxRpmIPortEntry  

hcxRpmIPortShelfId 1.3.6.1.4.1.1141.2.35.1.1.1
contains upstream shelf id containing the RX card.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

hcxRpmIPortSlotId 1.3.6.1.4.1.1141.2.35.1.1.2
contains upstream slot id containing the port. Presently there is one port per card.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmRxPortId 1.3.6.1.4.1.1141.2.35.1.1.3
Contains the id for the upstream port. Presently should be one only.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmIPortId 1.3.6.1.4.1.1141.2.35.1.1.4
Contains the id for the RPM I-port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

hcxRpmIPortRecvPower 1.3.6.1.4.1.1141.2.35.1.1.5
Contains the receiver power level in dBmv. Default is 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -15..15  

hcxRpmIPortConfigState 1.3.6.1.4.1.1141.2.35.1.1.6
Used to activate or deactivate the I-Port. For test purposes, one port can be enabled and all others disabled. This will cause the I-Port to be permanently closed. i.e. traffic passing. Default disable. Note that setting an I-Port to the disabled state will have the effect of clearing the statistics for the I-Port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

hcxRpmIPortContSchedType 1.3.6.1.4.1.1141.2.35.1.1.7
Used to control the type of contention slot scheduling utilized by this I-Port. The roundRobinOperation indicates that this I-Port shall have a individual contention opportunity - i.e. no other I-Ports active - allocated on a round-robin basis. The simultaneousOperation indicates that this I-Port shall be included with a group of I-Ports given the same, simultaneous contention opportunities. Default is roundRobinOperation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER roundRobinOperation(1), simultaneousOperation(2)  

com21HcxRpmStatsTable 1.3.6.1.4.1.1141.2.36.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HcxRpmStatsEntry

com21HcxRpmStatsEntry 1.3.6.1.4.1.1141.2.36.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  HcxRpmStatsEntry  

hcxStatsRpmShelfId 1.3.6.1.4.1.1141.2.36.1.1.1
Contains the id for the shelf in which the associated RX card is located.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

hcxStatsRpmSlotId 1.3.6.1.4.1.1141.2.36.1.1.2
Contains the id for the upstream slot.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxStatsRxPortId 1.3.6.1.4.1.1141.2.36.1.1.3
Contains the id for the upstream port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxStatsRpmIPortId 1.3.6.1.4.1.1141.2.36.1.1.4
Contains the id for the RPM I-Port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

hcxRpmCurrMinRxCells 1.3.6.1.4.1.1141.2.36.1.1.5
Represents the number of cells received via the I-Port in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRpmCurrMinRxNullCells 1.3.6.1.4.1.1141.2.36.1.1.6
Represents the number of null cells received via the RPM I-Port in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRpmCurrMinUncorFecHecCells 1.3.6.1.4.1.1141.2.36.1.1.7
Represents the number of received cells with either uncorrectable FEC or HEC errors received via the I-Port in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRpmCurrMinCorrectedFec 1.3.6.1.4.1.1141.2.36.1.1.8
Represents the number of corrected FEC errors received via the I-Port in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRpmCurrMeanNoise 1.3.6.1.4.1.1141.2.36.1.1.9
This attribute defines the mean noise value, in dBmv, sampled on the I-Port in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmCurrMinNoise 1.3.6.1.4.1.1141.2.36.1.1.10
Defines the minimum noise level, in dBmv, sampled on the I-Port in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmCurrMaxNoise 1.3.6.1.4.1.1141.2.36.1.1.11
Defines the maximum noise level, in dBmv, sampled on the I-Port in the current 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmRealTimeMeanNoise 1.3.6.1.4.1.1141.2.36.1.1.12
This attribute provides a realtime mean noise level in dBmv sampled on the I-Port. It is updated every approx 5 seconds and provides a snap shot of the noise conditions on this I-Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmRealTimeMinNoise 1.3.6.1.4.1.1141.2.36.1.1.13
This attribute provides a realtime min noise level in dBmv sampled on the I-Port. The attribute is updated every approx 5 seconds and provides the minimum noise level during that period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmRealTimeMaxNoise 1.3.6.1.4.1.1141.2.36.1.1.14
This attribute provides a realtime max noise level in dBmv sampled on the I-Port. The attribute is updated every approx 5 seconds and provides the maximum noise level during that period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmPrevMinRxCells 1.3.6.1.4.1.1141.2.36.1.1.15
Represents the number of cells received via the RPM I-Port in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRpmPrevMinRxNullCells 1.3.6.1.4.1.1141.2.36.1.1.16
Represents the number of null cells received via the I-Port in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRpmPrevMinUncorFecHecCells 1.3.6.1.4.1.1141.2.36.1.1.17
Represents the number of cells with uncorrectable FEC or HEC errors received via the I-Port in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRpmPrevMinCorrectedFec 1.3.6.1.4.1.1141.2.36.1.1.18
Represents the number of corrected FEC errors in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRpmPrevMeanNoise 1.3.6.1.4.1.1141.2.36.1.1.19
This attribute defines the mean noise value, in dBmv, sampled on the I-Port in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmPrevMinNoise 1.3.6.1.4.1.1141.2.36.1.1.20
Defines the minimum noise level, in dBmv, sampled on the I-Port in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmPrevMaxNoise 1.3.6.1.4.1.1141.2.36.1.1.21
Defines the maximum noise level, in dBmv, sampled on the I-Port in the previous 15 minute period.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRpmCorrFecRatioThres 1.3.6.1.4.1.1141.2.36.1.1.22
This attribute defines a threshold point at which a hop of the receive channel frequency shall take place. The threshold is defined as the percentage of corrected FEC errored cells to good cells. The RX card shall calculate this percentage over a one second period, and the threshold must be crossed for the period defined by the hcxRpmRatioThresPeriod attribute before a trap is generated. In addition the cells received within the second must be greater than that defined by hcxRpmMinErrRatioCells. A value of 0 disables the threshold. Default is 20.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

hcxRpmFecRatioThres 1.3.6.1.4.1.1141.4.84
Severity is WARNING.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxRpmCellErrRatioThres 1.3.6.1.4.1.1141.2.36.1.1.23
This attribute defines a threshold point at which a hop of the receive channel frequency shall take place. The threshold is defined as the percentage of FEC/HEC errored cells to good cells. The RX card shall calculate this percentage over a one second period, and the threshold must be crossed for the period defined by the hcxRpmRatioThresPeriod attribute before a trap is generated. In addition the cells received within one second must be greater than that defined by hcxRpmMinErrRatioCells. A value of 0 disables the threshold. Default is 10.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

hcxRpmCellErrRatioThresTrap 1.3.6.1.4.1.1141.4.85
Severity is WARNING.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxRpmRatioThresPeriod 1.3.6.1.4.1.1141.2.36.1.1.24
This attribute defines the integration period for the error ratio thresholds. This attribute defines the number of seconds over which the threshold is contiguously exceeded before a trap is generated. 0 disables the thresholds. Default is 5.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..900  

hcxRpmMinErrRatioCells 1.3.6.1.4.1.1141.2.36.1.1.25
This attribute defines the minimum number of cells that should be received per second in order to allow the Error and Corrected Cell Thresholds to cause a frequency hop. Default is 50.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..2500  

hcxRpmCnrThres 1.3.6.1.4.1.1141.2.36.1.1.26
Defines the average noise level, in dBmv, at which a frequency hop should occur. Note that the data error thresholds define above take precedence - this CNR threshold applies only if the data rate is less than the hcxRpmMinErrRatioCells. Default 11dBmv.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 7..16  

hcxRpmCnrThresTrap 1.3.6.1.4.1.1141.4.86
Tbd. Severity is WARNING.
Status: current Access: read-write
NOTIFICATION-TYPE    

hcxRpmClearStats 1.3.6.1.4.1.1141.2.36.1.1.27
This attribute is used to clear all RPM statistics counters in this group. This operation is only possible if the hcxStatsControl attribute is set to wrapCurr.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nil(1), clear(2)  

com21HcxRfAnalysisTable 1.3.6.1.4.1.1141.2.37.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HcxRfAnalysisEntry

com21HcxRfAnalysisEntry 1.3.6.1.4.1.1141.2.37.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  HcxRfAnalysisEntry  

hcxRfAnalysisShelfId 1.3.6.1.4.1.1141.2.37.1.1.1
contains upstream shelf id.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

hcxRfAnalysisSlotId 1.3.6.1.4.1.1141.2.37.1.1.2
contains upstream slot id.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRfAnalysisPortId 1.3.6.1.4.1.1141.2.37.1.1.3
contains upstream port id. Presently only one port is supported.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hcxRfAnalysisRpmPortId 1.3.6.1.4.1.1141.2.37.1.1.4
contains any RPM I-Port id. Note an RX card or RXM card operating without an RPM expects 1 for this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

hcxRfAnalysisControl 1.3.6.1.4.1.1141.2.37.1.1.5
Used to activate or deactivate the RF analysis for a port or I-Port. Default disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

hcxRfAnalysisPoint1 1.3.6.1.4.1.1141.2.37.1.1.6
This attribute is used to define the first, and lowest, noise level point. Default is -58dBmv.
Status: current Access: read-write
OBJECT-TYPE    
  RfAnalysisdBmv  

hcxRfAnalysisPoint2 1.3.6.1.4.1.1141.2.37.1.1.7
This attribute is used to define the second noise level point. This value must be greater than hcxRfAnalysisPoint1. Default is -15dBmv.
Status: current Access: read-write
OBJECT-TYPE    
  RfAnalysisdBmv  

hcxRfAnalysisPoint3 1.3.6.1.4.1.1141.2.37.1.1.8
This attribute is used to define the third noise level point. This value must be greater than hcxRfAnalysisPoint2. Default is -10dBmv.
Status: current Access: read-write
OBJECT-TYPE    
  RfAnalysisdBmv  

hcxRfAnalysisPoint4 1.3.6.1.4.1.1141.2.37.1.1.9
This attribute is used to define the final noise level point. This value must be greater than hcxRfAnalysisPoint3. Default is -5dBmv.
Status: current Access: read-write
OBJECT-TYPE    
  RfAnalysisdBmv  

hcxRfAnalysisBin1Count 1.3.6.1.4.1.1141.2.37.1.1.10
This attribute respresents the number of noise samples with levels between hcxRfAnalysisPoint1 and hcxRfAnalysisPoint2.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRfAnalysisBin2Count 1.3.6.1.4.1.1141.2.37.1.1.11
This attribute respresents the number of noise samples with levels between hcxRfAnalysisPoint2 and hcxRfAnalysisPoint3.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRfAnalysisBin3Count 1.3.6.1.4.1.1141.2.37.1.1.12
This attribute respresents the number of noise samples with levels between hcxRfAnalysisPoint3 and hcxRfAnalysisPoint4.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hcxRfAnalysisClearCount 1.3.6.1.4.1.1141.2.37.1.1.13
This attribute is used to clear the three RF analysis counts.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nil(1), clear(2)