CTRON-WAN-MIB

File: CTRON-WAN-MIB.mib (132874 bytes)

Imported modules

RFC-1212 CTRON-MIB-NAMES RFC1213-MIB
RFC1155-SMI

Imported symbols

OBJECT-TYPE ctWan DisplayString
IpAddress Counter

Defined Types

Index  
INTEGER    

DLCI  
INTEGER    

WanConnEntry  
SEQUENCE    
  wanConnIndex INTEGER
  wanConnNumPhysPorts INTEGER
  wanConnDefaultPhysPort INTEGER
  wanConnActivePhysPort INTEGER

WanPhysPortEntry  
SEQUENCE    
  wanPhysPortConnectionIndex INTEGER
  wanPhysPortIndex INTEGER
  wanPhysPortType INTEGER
  wanPhysPortSpecificMib OBJECT IDENTIFIER

WanInterfaceEntry  
SEQUENCE    
  wanInterfaceConnectionIndex INTEGER
  wanInterfacePhysPortIndex INTEGER
  wanInterfaceEntryIndex INTEGER
  wanInterfaceEntryIfIndex INTEGER
  wanInterfaceEntryProtocol INTEGER
  wanInterfaceEntryCompression INTEGER
  wanInterfaceEntryMTU INTEGER
  wanInterfaceEntryLineCoding INTEGER
  wanInterfaceEntryCrcLength INTEGER
  wanInterfaceEntryLexProtocolEnable INTEGER
  wanInterfaceEntryLexProtocolStatus INTEGER
  wanInterfaceEntryCompRatio OCTET STRING
  wanInterfaceEntryCompStatus INTEGER
  wanInterfaceEntryBackUpIfEnable INTEGER

WanDs1ExtensionsEntry  
SEQUENCE    
  wanDs1ExtensionsEntryIndex INTEGER
  wanDs1ExtensionsNumInterfaces INTEGER
  wanDs1ExtensionsToggleFracTable INTEGER
  wanDs1ExtensionsLineBuildOut INTEGER
  wanDs1ExtensionsCFADuration INTEGER
  wanDs1ExtensionsDIEnable INTEGER
  wanDs1ExtensionsTotalValidIntervals Counter
  wanDs1ExtensionsBertTestMode INTEGER
  wanDs1ExtensionsBertRun INTEGER
  wanDs1ExtensionsBertCurrentResults INTEGER
  wanDs1ExtensionsBertCumulativeResults INTEGER
  wanDs1ExtensionsBertPeakResults INTEGER
  wanDs1ExtensionsBertAverageResult INTEGER
  wanDs1ExtensionsBertTestPattern INTEGER
  wanDs1ExtensionsBertSamplePeriod INTEGER
  wanDs1ExtensionsBertNumPeriods Counter
  wanDs1ExtensionsBertTestTraps INTEGER
  wanDs1ExtensionsBertDataStatus INTEGER

WanRs232ExtensionsEntry  
SEQUENCE    
  wanRs232ExtensionsEntryIndex INTEGER
  wanRs232ExtensionsCTSEnable INTEGER
  wanRs232ExtensionsDSREnable INTEGER

FrDcpCircuitEntry  
SEQUENCE    
  frDcpCircuitIfIndex Index
  frDcpCircuitDlci DLCI
  frDcpCircuitEnable INTEGER
  frDcpCircuitStatus INTEGER
  frDcpCircuitRatio OCTET STRING

DdsConfigEntry  
SEQUENCE    
  ddsLineIndex INTEGER
  ddsIfIndex INTEGER
  ddsLineMode INTEGER
  ddsLineCoding INTEGER
  ddsLoopbackConfig INTEGER
  ddsLineStatus INTEGER
  ddsTxClockSource INTEGER
  ddsPortInSpeed INTEGER
  ddsPortOutSpeed INTEGER

Ds1AlarmConfigEntry  
SEQUENCE    
  ds1PhysNum INTEGER
  ds1AlarmAdmin INTEGER
  ds1AlarmAutoRecovery INTEGER
  ds1AlarmTrapEnable INTEGER
  ds1AlarmESCount INTEGER
  ds1AlarmESInterval INTEGER
  ds1AlarmBPVErrorRate INTEGER
  ds1AlarmBPVInterval INTEGER
  ds1AlarmManualRecovery INTEGER

IpPQAddressEntry  
SEQUENCE    
  ipPQAddressId INTEGER
  ipPQIPAddress IpAddress

CtWanHDSLPerformance15mEntry  
SEQUENCE    
  ctWanHDSLPerformance15mConnIndex INTEGER
  ctWanHDSLPerformance15mSlotIndex INTEGER
  ctWanHDSLHLULoop1UAS15m INTEGER
  ctWanHDSLHLULoop1ES15m INTEGER
  ctWanHDSLHLULoop2UAS15m INTEGER
  ctWanHDSLHLULoop2ES15m INTEGER
  ctWanHDSLHRULoop1UAS15m INTEGER
  ctWanHDSLHRULoop1ES15m INTEGER
  ctWanHDSLHRULoop2UAS15m INTEGER
  ctWanHDSLHRULoop2ES15m INTEGER
  ctWanHDSLDb1NetworkLoop1UAS15m INTEGER
  ctWanHDSLDb1NetworkLoop1ES15m INTEGER
  ctWanHDSLDb1NetworkLoop2UAS15m INTEGER
  ctWanHDSLDb1NetworkLoop2ES15m INTEGER
  ctWanHDSLDb1CustomerLoop1UAS15m INTEGER
  ctWanHDSLDb1CustomerLoop1ES15m INTEGER
  ctWanHDSLDb1CustomerLoop2UAS15m INTEGER
  ctWanHDSLDb1CustomerLoop2ES15m INTEGER
  ctWanHDSLDb2NetworkLoop1UAS15m INTEGER
  ctWanHDSLDb2NetworkLoop1ES15m INTEGER
  ctWanHDSLDb2NetworkLoop2UAS15m INTEGER
  ctWanHDSLDb2NetworkLoop2ES15m INTEGER
  ctWanHDSLDb2CustomerLoop1UAS15m INTEGER
  ctWanHDSLDb2CustomerLoop1ES15m INTEGER
  ctWanHDSLDb2CustomerLoop2UAS15m INTEGER
  ctWanHDSLDb2CustomerLoop2ES15m INTEGER

CtWanHDSLPerformance24hEntry  
SEQUENCE    
  ctWanHDSLPerformance24hConnIndex INTEGER
  ctWanHDSLPerformance24hSlotIndex INTEGER
  ctWanHDSLHLULoop1UAS24h INTEGER
  ctWanHDSLHLULoop1ES24h INTEGER
  ctWanHDSLHLULoop2UAS24h INTEGER
  ctWanHDSLHLULoop2ES24h INTEGER
  ctWanHDSLHRULoop1UAS24h INTEGER
  ctWanHDSLHRULoop1ES24h INTEGER
  ctWanHDSLHRULoop2UAS24h INTEGER
  ctWanHDSLHRULoop2ES24h INTEGER
  ctWanHDSLDb1NetworkLoop1UAS24h INTEGER
  ctWanHDSLDb1NetworkLoop1ES24h INTEGER
  ctWanHDSLDb1NetworkLoop2UAS24h INTEGER
  ctWanHDSLDb1NetworkLoop2ES24h INTEGER
  ctWanHDSLDb1CustomerLoop1UAS24h INTEGER
  ctWanHDSLDb1CustomerLoop1ES24h INTEGER
  ctWanHDSLDb1CustomerLoop2UAS24h INTEGER
  ctWanHDSLDb1CustomerLoop2ES24h INTEGER
  ctWanHDSLDb2NetworkLoop1UAS24h INTEGER
  ctWanHDSLDb2NetworkLoop1ES24h INTEGER
  ctWanHDSLDb2NetworkLoop2UAS24h INTEGER
  ctWanHDSLDb2NetworkLoop2ES24h INTEGER
  ctWanHDSLDb2CustomerLoop1UAS24h INTEGER
  ctWanHDSLDb2CustomerLoop1ES24h INTEGER
  ctWanHDSLDb2CustomerLoop2UAS24h INTEGER
  ctWanHDSLDb2CustomerLoop2ES24h INTEGER

CtWanHDSLStatisticsEntry  
SEQUENCE    
  ctWanHDSLStatisticsHLUConnIndex INTEGER
  ctWanHDSLSNRHLULoop1 INTEGER
  ctWanHDSLSNRLowHLULoop1 INTEGER
  ctWanHDSLSNRHighHLULoop1 INTEGER
  ctWanHDSLSNRHLULoop2 INTEGER
  ctWanHDSLSNRLowHLULoop2 INTEGER
  ctWanHDSLSNRHighHLULoop2 INTEGER
  ctWanHDSLPulseAttenuationHLULoop1 INTEGER
  ctWanHDSLPulseAttenuationHLULoop2 INTEGER
  ctWanHDSLBitStat1HLU INTEGER
  ctWanHDSLSNRHRULoop1 INTEGER
  ctWanHDSLSNRLowHRULoop1 INTEGER
  ctWanHDSLSNRHighHRULoop1 INTEGER
  ctWanHDSLSNRHRULoop2 INTEGER
  ctWanHDSLSNRLowHRULoop2 INTEGER
  ctWanHDSLSNRHighHRULoop2 INTEGER
  ctWanHDSLPulseAttenuationHRULoop1 INTEGER
  ctWanHDSLPulseAttenuationHRULoop2 INTEGER
  ctWanHDSLDs1FrameHRU INTEGER
  ctWanHDSLSNRDb1NetworkLoop1 INTEGER
  ctWanHDSLSNRLowDb1NetworkLoop1 INTEGER
  ctWanHDSLSNRHighDb1NetworkLoop1 INTEGER
  ctWanHDSLSNRDb1NetworkLoop2 INTEGER
  ctWanHDSLSNRLowDb1NetworkLoop2 INTEGER
  ctWanHDSLSNRHighDb1NetworkLoop2 INTEGER
  ctWanHDSLSNRDb1CustomerLoop1 INTEGER
  ctWanHDSLSNRLowDb1CustomerLoop1 INTEGER
  ctWanHDSLSNRHighDb1CustomerLoop1 INTEGER
  ctWanHDSLSNRDb1CustomerLoop2 INTEGER
  ctWanHDSLSNRLowDb1CustomerLoop2 INTEGER
  ctWanHDSLSNRHighDb1CustomerLoop2 INTEGER
  ctWanHDSLPulseAttenuationDb1NetworkLoop1 INTEGER
  ctWanHDSLPulseAttenuationDb1NetworkLoop2 INTEGER
  ctWanHDSLPulseAttenuationDb1CustomerLoop1 INTEGER
  ctWanHDSLPulseAttenuationDb1CustomerLoop2 INTEGER
  ctWanHDSLSNRDb2NetworkLoop1 INTEGER
  ctWanHDSLSNRLowDb2NetworkLoop1 INTEGER
  ctWanHDSLSNRHighDb2NetworkLoop1 INTEGER
  ctWanHDSLSNRDb2NetworkLoop2 INTEGER
  ctWanHDSLSNRLowDb2NetworkLoop2 INTEGER
  ctWanHDSLSNRHighDb2NetworkLoop2 INTEGER
  ctWanHDSLSNRDb2CustomerLoop1 INTEGER
  ctWanHDSLSNRLowDb2CustomerLoop1 INTEGER
  ctWanHDSLSNRHighDb2CustomerLoop1 INTEGER
  ctWanHDSLSNRDb2CustomerLoop2 INTEGER
  ctWanHDSLSNRLowDb2CustomerLoop2 INTEGER
  ctWanHDSLSNRHighDb2CustomerLoop2 INTEGER
  ctWanHDSLPulseAttenuationDb2NetworkLoop1 INTEGER
  ctWanHDSLPulseAttenuationDb2NetworkLoop2 INTEGER
  ctWanHDSLPulseAttenuationDb2CustomerLoop1 INTEGER
  ctWanHDSLPulseAttenuationDb2CustomerLoop2 INTEGER

CtWanHDSLTestEntry  
SEQUENCE    
  ctWanHDSLTestHLUConnIndex INTEGER
  ctWanHDSLTestMode INTEGER
  ctWanHDSLHLUTestResult INTEGER
  ctWanHDSLHRUTestResult INTEGER

CtWanHDSLAlarmsEntry  
SEQUENCE    
  ctWanHDSLAlarmsHLUConnIndex INTEGER
  ctWanHDSLAlarmsBackplane INTEGER
  ctWanHDSLAlarmsES INTEGER

CtWanHDSLAlarmHistoryEntry  
SEQUENCE    
  ctWanHDSLAlarmHistoryConnIndex INTEGER
  ctWanHDSLAlHistLLOSFirst DisplayString Size(12)
  ctWanHDSLAlHistLLOSLast DisplayString Size(12)
  ctWanHDSLAlHistLLOSCurrent INTEGER
  ctWanHDSLAlHistLLOSCount INTEGER
  ctWanHDSLAlHistRLOSFirst DisplayString Size(12)
  ctWanHDSLAlHistRLOSLast DisplayString Size(12)
  ctWanHDSLAlHistRLOSCurrent INTEGER
  ctWanHDSLAlHistRLOSCount INTEGER
  ctWanHDSLAlHistLOSW1First DisplayString Size(12)
  ctWanHDSLAlHistLOSW1Last DisplayString Size(12)
  ctWanHDSLAlHistLOSW1Current INTEGER
  ctWanHDSLAlHistLOSW1Count INTEGER
  ctWanHDSLAlHistLOSW2First DisplayString Size(12)
  ctWanHDSLAlHistLOSW2Last DisplayString Size(12)
  ctWanHDSLAlHistLOSW2Current INTEGER
  ctWanHDSLAlHistLOSW2Count INTEGER
  ctWanHDSLAlHistES1First DisplayString Size(12)
  ctWanHDSLAlHistES1Last DisplayString Size(12)
  ctWanHDSLAlHistES1Current INTEGER
  ctWanHDSLAlHistES1Count INTEGER
  ctWanHDSLAlHistES2First DisplayString Size(12)
  ctWanHDSLAlHistES2Last DisplayString Size(12)
  ctWanHDSLAlHistES2Current INTEGER
  ctWanHDSLAlHistES2Count INTEGER
  ctWanHDSLAlHistMargin1First DisplayString Size(12)
  ctWanHDSLAlHistMargin1Last DisplayString Size(12)
  ctWanHDSLAlHistMargin1Current INTEGER
  ctWanHDSLAlHistMargin1Count INTEGER
  ctWanHDSLAlHistMargin2First DisplayString Size(12)
  ctWanHDSLAlHistMargin2Last DisplayString Size(12)
  ctWanHDSLAlHistMargin2Current INTEGER
  ctWanHDSLAlHistMargin2Count INTEGER
  ctWanHDSLAlHistCleared DisplayString Size(12)
  ctWanHDSLAlHistClearit INTEGER

CtWanHDSLLoopbacksEntry  
SEQUENCE    
  ctWanHDSLLoopbacksHLUConnIndex INTEGER
  ctWanHDSLLoopbacksAdminType INTEGER
  ctWanHDSLLoopbacksOperType INTEGER

Defined Values

ctWanConnection 1.3.6.1.4.1.52.4.1.2.7.1.1
OBJECT IDENTIFIER    

ctWanDs1 1.3.6.1.4.1.52.4.1.2.7.1.2
OBJECT IDENTIFIER    

ctWanRs232 1.3.6.1.4.1.52.4.1.2.7.1.3
OBJECT IDENTIFIER    

ctFrDcp 1.3.6.1.4.1.52.4.1.2.7.1.4
OBJECT IDENTIFIER    

ctDDS 1.3.6.1.4.1.52.4.1.2.7.1.5
OBJECT IDENTIFIER    

ctDs1Alarms 1.3.6.1.4.1.52.4.1.2.7.1.6
OBJECT IDENTIFIER    

ctIPPQFilters 1.3.6.1.4.1.52.4.1.2.7.1.7
OBJECT IDENTIFIER    

ctWanHDSLExt 1.3.6.1.4.1.52.4.1.2.7.1.8
OBJECT IDENTIFIER    

wanNumConnections 1.3.6.1.4.1.52.4.1.2.7.1.1.1
This objects describes the number of wan connections on the platform. A wan connection may have one or two physical ports of which only one can be active at any time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanConnTable 1.3.6.1.4.1.52.4.1.2.7.1.1.2
A list of wan connection entries. The number of wan connection entries is given by the value of wanNumConnections.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WanConnEntry

wanConnEntry 1.3.6.1.4.1.52.4.1.2.7.1.1.2.1
A wan connection entry containing objects relating to the particular wan connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WanConnEntry  

wanConnIndex 1.3.6.1.4.1.52.4.1.2.7.1.1.2.1.1
A unique value for each wan connection. Its value ranges between 1 and the value wanNumConnections.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanConnNumPhysPorts 1.3.6.1.4.1.52.4.1.2.7.1.1.2.1.2
The number of physical ports that exist on this wan connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanConnDefaultPhysPort 1.3.6.1.4.1.52.4.1.2.7.1.1.2.1.3
The default physical port for this connection. This indicates the physical port that should be used on this wan connection. If redundancy is not enabled, this physical port will always be used. If redundancy is enabled, the physical port given here will be considered the primary physical port. The value of this object must be set to the index of a valid physical port (wanPhysPortIndex) for this wan connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wanConnActivePhysPort 1.3.6.1.4.1.52.4.1.2.7.1.1.2.1.4
The physical port that is currently active for this wan connection. The value of this object indicates the wanPhysPortIndex for the active port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanPhysPortTable 1.3.6.1.4.1.52.4.1.2.7.1.1.3
A list of the descriptions of the physical ports of this platform. The number of entries is given by the value of wanConnNumPhysPort for each Wan Connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WanPhysPortEntry

wanPhysPortEntry 1.3.6.1.4.1.52.4.1.2.7.1.1.3.1
A physical port entry. It contains objects relating to a given physical port
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WanPhysPortEntry  

wanPhysPortConnectionIndex 1.3.6.1.4.1.52.4.1.2.7.1.1.3.1.1
A value indicating the wan connection this physical port is located on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanPhysPortIndex 1.3.6.1.4.1.52.4.1.2.7.1.1.3.1.2
A unique value for each physical port on a wan connection. Its value ranges between 1 and the value wanConnNumPhysPorts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanPhysPortType 1.3.6.1.4.1.52.4.1.2.7.1.1.3.1.3
The type of physical port that this entry describes. None indicates that the physical port has no connector.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), t1(2), e1(3), synchronous(4), dds(5), di(6), hdsl(7), bri(8), ds30(9), t1DDS(10)  

wanPhysPortSpecificMib 1.3.6.1.4.1.52.4.1.2.7.1.1.3.1.4
This object identifies an instance of the index object in the first group of objects in the MIB specific to the physical port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanInterfaceTable 1.3.6.1.4.1.52.4.1.2.7.1.1.4
The interface table for a physical port on a wan connection. It is a list of items that are pertinent to the interfaces that are part of this physical port. The number of entries is dependent on the wanPhysPortType for the interface. If the wanPhysPortType is none, there will be no entries in the table for the port. If the wanPhysPortType is t1, there will be 24 entries in this table for the port. If the wanPhysPortType is e1, there will be 30 entries in this table for the port. If the wanPhysPortType is synchronous, there will be one entry in this table for the port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WanInterfaceEntry

wanInterfaceEntry 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1
A wan connection physical port interface entry. It contains objects relating to an interface that is defined for this physical port and this wan connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WanInterfaceEntry  

wanInterfaceConnectionIndex 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.1
This value is the wan connection that this interface exists on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanInterfacePhysPortIndex 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.2
This value is the physical port of the wan connection that this interface exists on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanInterfaceEntryIndex 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.3
A unique value for each interface of this physical port. It is a value between 1 and the number of interfaces that exist for the current port. The number of interfaces for each type of port is: 24 for a port type (wanPhysPortType) of 't1', 30 for a port type of 'e1', and 1 for a port type of 'synchronous'. There will be no entries if the port type is 'none'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanInterfaceEntryIfIndex 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.4
The ifIndex of the interface. This is the index of this entry in the ifTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanInterfaceEntryProtocol 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.5
The protocol that should be run on this interface. Values are equivalent to those defined for ifType in Mib-II. Accepted values are product dependent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wanInterfaceEntryCompression 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.6
Indicates whether data compression should take place on this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wanInterfaceEntryMTU 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.7
The MTU to be negotiated for this interface. This will not be updated with the actual MTU, which can be found in the ifTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wanInterfaceEntryLineCoding 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.8
This object describes the variety of Zero Code suppression on this interface. For an interface on a Ds1 Port, the valid values depend on the value of the Ds1ConfigLineCode object. If that object is set to ds1xB8ZS, then this object can be set to none, JBZS, or InvHDLC. If the value of Ds1ConfigLineCode is set to ds1xAMI, then this object can only be set to JBZS, or InvHDLC. For an interface on a Synchronous Port, the valid values are none or InvHDLC. JBZS refers to Jammed Bit Zero suppression, which forces a 1 bit every 8 bit periods. InvHDLC refers to inverting the HDLC data for the interface. None refers to a mode in which some other means, such as with the Ds1ConfigLineCode object set to dsx1B8ZS, is used to insure pulse density requirements.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), jBZS(2), invHDLC(3)  

wanInterfaceEntryCrcLength 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.9
The Length of the CRC for this interface. Not all platforms will allow all options.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sixteen-bits(1), thirty-two-bits(2)  

wanInterfaceEntryLexProtocolEnable 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.10
This switch acts in concert with the wanInterfaceEntryProtocol object. To activate LEX, this object should first be set to enable (1), then set the wanInterfaceEntryProtocol to PPP. The enable will have no effect if PPP is not selected. If the wanInterfaceEntryProtocol is selected first, the default NCP of BNCP will be selected. To De-select LEX, you must set this object to disable (2), and wanInterfaceEntryProtocol to NONE or reset the device. Just selecting disable (2) will not tear down the connection.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wanInterfaceEntryLexProtocolStatus 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.11
This object reflects the current state of the link. The device is said to be bound to the router when the physical link is OK, the LEX negotiation is successful, and the router has been configured correctly to communicate with this particular LAN Extender.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER bound(1), unbound(2)  

wanInterfaceEntryCompRatio 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.12
The ratio of uncompressed to compressed transmitted data. If the data compression status is off, 1:1 will be displayed
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

wanInterfaceEntryCompStatus 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.13
On indicates that the compression has been successfully negotiated and is operating. Off indicates that the compression negotiation has failed and compression is not operating at this time, or compression has been terminated by either peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wanInterfaceEntryBackUpIfEnable 1.3.6.1.4.1.52.4.1.2.7.1.1.4.1.14
This object is used to select the Call-backup option. A value of 1 is used to enable the option and a value of 2 to disable it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wanDs1ExtensionsTable 1.3.6.1.4.1.52.4.1.2.7.1.2.1
This table is an extension to the standard ds1 configuration table. It is a list of items that are pertinent to ds1 ports on a platform. There is one entry per ds1 physical port on the platform
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WanDs1ExtensionsEntry

wanDs1ExtensionsEntry 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1
A ds1 extensions entry containing objects relating to the particular ds1 physical port
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WanDs1ExtensionsEntry  

wanDs1ExtensionsEntryIndex 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.1
A unique value for each ds1 physical port on the platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsNumInterfaces 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.2
The number of interfaces on this physical port. This number indicates the number of entries this physical port uses in the ifTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsToggleFracTable 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.3
Setting this object to 1 will cause the Ds1 Fractional Table to be updated with the new values, as entered. Setting this object to 2, will cause the Ds1 Fractional Table to view as the table being entered. Setting this object to 3, will cause the Ds1 Fractional Table to be the table that is currently in use, regardless of any changes being entered. Setting this object to 4, will cause any changes that have been made to the Ds1 Fractional Table since the last update-table to be deleted. For physical ports of type synchronous, this object will have no affect, and will always return a 1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER update-table(1), display-new(2), display-old(3), restore-old(4)  

wanDs1ExtensionsLineBuildOut 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.4
The line build out setting for this ds1 physical port. Unknown indicates that the setting is neither readable or writable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), zero(2), minus-7point5(3), minus-15(4), a133to266feet(5), a266to399feet(6), a399to533feet(7), a533to655feet(8)  

wanDs1ExtensionsCFADuration 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.5
The length of time (in seconds), that the ds1 port will remain in the Carrier Failure Alarm state after the alarm condition has cleared.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

wanDs1ExtensionsDIEnable 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.6
Enables or disables Drop and Insert functionality on a D/I WPIM. If enabled, all zero assigned timeslots will designate D/I interface channels, if disabled all zero channels will designate dummy channels as on a T1 or E1. If this object is set to diDataEnabled the zero channels will designate D/I interface channels and data to and from the device will be transmitted or received on the D/I port instead of the N/I port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), diDataEnabled(3)  

wanDs1ExtensionsTotalValidIntervals 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.7
The number of previous intervals for which valid data was collected for the DS1 mib, which is currently RFC1406. This counter is similar to RFC1406 dsx1ValidIntervals except that the count represents the total number of complete 15 minute intervals since the ds1 interface has been online, and does not stop at the 24 hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wanDs1ExtensionsBertTestMode 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.8
This object is used to request that a type of process be in control of the testing function. This is used to differentiate between automated test procedures and those manually controlled by a user. When read, this object reflects which type of process is actually in control of the testing function. The implementation is free to prioritize or deny requests in a proprietary manner.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), internal(2), manual(3)  

wanDs1ExtensionsBertRun 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.9
Controls the sending of test data over this physical port. The data is a pattern described by wanDs1ExtensionsBertTestPattern.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

wanDs1ExtensionsBertCurrentResults 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.10
Indicates the results of the testing for the last completed sampling period. A non-negative number is the error rate in bits per million bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsBertCumulativeResults 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.11
Indicates the total number of errors since the testing was enabled. It is not a rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsBertPeakResults 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.12
Indicates the highest value of wanDs1ExtensionsBertCurrentResults since the testing was enabled. A non-negative number is the error rate in bits per million bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsBertAverageResult 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.13
Indicates the average value of wanDs1ExtensionsBertCurrentResults since the testing was enabled. A non-negative number is the error rate in bits per million bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsBertTestPattern 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.14
This object is used to specify the pattern of the test data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER patternOther(1), pattern1s(2), pattern63(3), pattern511(4), pattern2047(5), pattern3in24(6), patternQRSS(7)  

wanDs1ExtensionsBertSamplePeriod 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.15
This object is the duration of time in seconds at which the current test results will be periodically written to wanDs1ExtensionsBertCurrentResults. The range is 1 to 3600, with a default value of 10.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsBertNumPeriods 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.16
The number of sampling periods that have elapsed during the current test run.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wanDs1ExtensionsBertTestTraps 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.17
This object is used to enable or disable the sending of a trap at the conclusion of the measurement period. The trap will contain the information described by ctDs1BertCurrentResults. The default value is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

wanDs1ExtensionsBertDataStatus 1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.18
This object provides the operating status of the transmission of test data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(1), waitingForLink(2), waitingForLoopback(3), running(4)  

wanRs232ExtensionsTable 1.3.6.1.4.1.52.4.1.2.7.1.3.1
This table is an extension to the standard rs232-like mib. It is a list of items that are pertinent to rs232-like ports on a platform. There is one entry per synchronous physical port on the platform.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WanRs232ExtensionsEntry

wanRs232ExtensionsEntry 1.3.6.1.4.1.52.4.1.2.7.1.3.1.1
A rs232-like extensions entry containing objects relating to the particular rs232-like physical port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WanRs232ExtensionsEntry  

wanRs232ExtensionsEntryIndex 1.3.6.1.4.1.52.4.1.2.7.1.3.1.1.1
A unique value for each rs232-like physical port on the platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanRs232ExtensionsCTSEnable 1.3.6.1.4.1.52.4.1.2.7.1.3.1.1.2
This object indicates whether the platform should generate CTS. When disabled the platform will not generate CTS, when enabled, the platform will generate CTS. The actual state of the CTS line is available in the rs-232 like mib.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wanRs232ExtensionsDSREnable 1.3.6.1.4.1.52.4.1.2.7.1.3.1.1.3
This object indicates whether the platform should generate DSR. When disabled the platform will not generate DSR, when enabled, the platform will generate DSR. The actual state of the DSR line is available in the rs-232 like mib.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

frDcpCircuitTable 1.3.6.1.4.1.52.4.1.2.7.1.4.1
A table containing data compression information about specific Data Link Connection Identifiers and corresponding virtual circuit. This information is used to support the frCircuitTable following RFC-1315.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDcpCircuitEntry

frDcpCircuitEntry 1.3.6.1.4.1.52.4.1.2.7.1.4.1.1
The data compression information regarding a single Data Link Connection Identifier.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDcpCircuitEntry  

frDcpCircuitIfIndex 1.3.6.1.4.1.52.4.1.2.7.1.4.1.1.1
The ifIndex value of ifEntry that this DCP virtual circuit object is layered onto.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Index  

frDcpCircuitDlci 1.3.6.1.4.1.52.4.1.2.7.1.4.1.1.2
The Data Link Connection Identifier for this DCP virtual circuit object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DLCI  

frDcpCircuitEnable 1.3.6.1.4.1.52.4.1.2.7.1.4.1.1.3
Indicates whether data compression should take place on this particular end side virtual circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

frDcpCircuitStatus 1.3.6.1.4.1.52.4.1.2.7.1.4.1.1.4
On indicates that the compression has been successfully negotiated and is operating. Off indicates that the compression negotiation has failed and compression is not operating at this time, or compression has been terminated by either peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

frDcpCircuitRatio 1.3.6.1.4.1.52.4.1.2.7.1.4.1.1.5
The ratio of uncompressed to compressed transmitted data. If the data compression status is off, 1:1 will be displayed
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(5)  

ddsConfigTable 1.3.6.1.4.1.52.4.1.2.7.1.5.1
The DDS Configuration Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DdsConfigEntry

ddsConfigEntry 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1
An Entry in the DDS Configuration Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DdsConfigEntry  

ddsLineIndex 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.1
A unique value for each dds physical port on the platform
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ddsIfIndex 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.2
Index associated with this dds physical port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ddsLineMode 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.3
DDS-PRI is full duplex 56k link, No framing in loop data so loop speed is also 56k. Data stream: --d1 d2 d3 d4 d5 d6 d7-- DDS-CC is full duplex 64k link. Does not require framing bit but uses a same format as SC, ninth bit position is lumped with primary channel and not used for control. Loop speed is 72k, Primary channel rate is 64k. --d1 d2 d3 d4 d5 d6 d7 F d8--
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ddsPri(1), ddsCc(2)  

ddsLineCoding 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.4
This object describes the variety of Zero Code suppression on this interface. JBZS refers to Jammed Bit Zero suppression, which forces a 1 bit every 8 bit periods. None refers to a mode in which some other means is used to insure pulse density requirements.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ddsNone(1), ddsJBZS(2), otherLineCode(3)  

ddsLoopbackConfig 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.5
This variable represents the loop-back configuration of the DDS interface. ddsNoLoop means the interface is not in loop-back state, and LineLoop means the the received data is looped back out.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ddsNoLoop(1), ddsLineLoop(2)  

ddsLineStatus 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.6
This describes the current operational status of DDS line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ddsNoAlarm(1), ddsLossOfSignal(2), ddsOutOfService(3), ddsOutOfFrame(4)  

ddsTxClockSource 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.7
The source of Transmit clock. ddsLoopTiming - indicates that the recovered receive clock is used as transmit clock. ddsLocalTiming - indicates that a local clock source is used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ddsLoopTiming(1), ddsLocalTiming(2)  

ddsPortInSpeed 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.8
This variable describes the current operational receive speed of DDS line. It is a read only value based entirely on DDS type (CC or PRI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ddsPortOutSpeed 1.3.6.1.4.1.52.4.1.2.7.1.5.1.1.9
This variable describes the current operational transmit speed of DDS line. It is a read only value based entirely on DDS type CC or PRI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ds1AlarmsGlobalConfigGroup 1.3.6.1.4.1.52.4.1.2.7.1.6.1
OBJECT IDENTIFIER    

ds1AlarmGlobalAdmin 1.3.6.1.4.1.52.4.1.2.7.1.6.1.1
Used to enable and disable the DS1 Alarm Monitoring Application for all DS1 circuits on the device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmGlobalAutoRecovery 1.3.6.1.4.1.52.4.1.2.7.1.6.1.2
Used to enable and disable the DS1 Alarm Automatic Recovery feature for all DS1 circuits on the device. For those devices that support ds1 alarm monitoring, but do not support the automatic recovery feature, this object always returns disabled, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmGlobalTrapEnable 1.3.6.1.4.1.52.4.1.2.7.1.6.1.3
Used to enable and disable the DS1 Alarm SNMP Trap generation feature for all DS1 circuits on the device. This object operates in conjunction with configuration of objects in the ctron-trap-mib.txt
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmGlobalESCount 1.3.6.1.4.1.52.4.1.2.7.1.6.1.4
Used in conjuction with ctDs1AlarmESInterval to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..300  

ds1AlarmGlobalESInterval 1.3.6.1.4.1.52.4.1.2.7.1.6.1.5
Used in conjuction with ds1AlarmGlobalESCount to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

ds1AlarmGlobalBPVErrorRate 1.3.6.1.4.1.52.4.1.2.7.1.6.1.6
Used to specify the negative exponent of 10, used in monitoring Bipolar Violations (Code Violations for E1) over intervals defined by ds1AlarmGlobalBPVInterval. For example, for a ds1AlarmGlobalBPVErrorRate value of 6 used with a ds1AlarmGlobalBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..9  

ds1AlarmGlobalBPVInterval 1.3.6.1.4.1.52.4.1.2.7.1.6.1.7
Used to specify the interval, used in monitoring Bipolar Violations (Code Violations for E1) with thresholds defined by ds1AlarmGlobalBPVErrorRate. For example, for a ds1AlarmGlobalBPVErrorRate value of 6 used with a ds1AlarmGlobalBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not detect bipolar violations, this object always returns the default, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

ds1AlarmGlobalManualRecovery 1.3.6.1.4.1.52.4.1.2.7.1.6.1.8
To cause a manual recovery to occur on all Ds1 circuits, this object is set to a 1. It is always read as a 1. The recovery will occur only when automatic recovery is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER recover(1)  

ds1AlarmConfigTable 1.3.6.1.4.1.52.4.1.2.7.1.6.2
Table containing objects used to configure DS1 alarm functionality on a per DS1 basis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Ds1AlarmConfigEntry

ds1AlarmConfigEntry 1.3.6.1.4.1.52.4.1.2.7.1.6.2.1
A description of a single entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Ds1AlarmConfigEntry  

ds1PhysNum 1.3.6.1.4.1.52.4.1.2.7.1.6.2.1.1
The value for this object is equal to the value of a unique physical connection identifier associated with this DS1 which is clearly labeled on the device. For those products that do not have a DS1 identifier labeled on the device, the value for this object is the same as rfc1406 dsx1LineIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ds1AlarmAdmin 1.3.6.1.4.1.52.4.1.2.7.1.6.2.1.2
Used to enable and disable the DS1 Alarm Monitoring Application for this DS1 circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmAutoRecovery 1.3.6.1.4.1.52.4.1.2.7.1.6.2.1.3
Used to enable and disable the DS1 Alarm Automatic Recovery feature for this DS1 circuit. For those devices that support ds1 alarm monitoring, but do not support the automatic recovery feature, this object always returns disabled, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmTrapEnable 1.3.6.1.4.1.52.4.1.2.7.1.6.2.1.4
Used to enable and disable the DS1 Alarm SNMP Trap generation feature for this DS1 circuit. This object operates in conjunction with configuration of objects in the ctron-trap-mib.txt
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmESCount 1.3.6.1.4.1.52.4.1.2.7.1.6.2.1.5
Used in conjuction with ctDs1AlarmESInterval to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..300  

ds1AlarmESInterval 1.3.6.1.4.1.52.4.1.2.7.1.6.2.1.6
Used in conjuction with ctDs1AlarmESCount to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

ds1AlarmBPVErrorRate 1.3.6.1.4.1.52.4.1.2.7.1.6.2.1.7
Used to specify the negative exponent of 10, used in monitoring Bipolar Violations (Code Violations for E1) over intervals defined by ds1AlarmBPVInterval. For example, for a ds1AlarmBPVErrorRate value of 6 used with a ds1AlarmBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..9  

ds1AlarmBPVInterval 1.3.6.1.4.1.52.4.1.2.7.1.6.2.1.8
Used to specify the interval, used in monitoring Bipolar Violations (Code Violations for E1) with thresholds defined by ds1AlarmBPVErrorRate. For example, for a ds1AlarmBPVErrorRate value of 6 used with a ds1AlarmBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

ds1AlarmManualRecovery 1.3.6.1.4.1.52.4.1.2.7.1.6.2.1.9
To cause a manual recovery to occur, this object is set to a 1. It is always read as a 1. The recovery will occur only when automatic recovery is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER recover(1)  

ipPQConfigGroup 1.3.6.1.4.1.52.4.1.2.7.1.7.1
OBJECT IDENTIFIER    

ipPQAdmin 1.3.6.1.4.1.52.4.1.2.7.1.7.1.1
Used to enable and disable the IP Priority Queue Forwarding Application.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

iPPQMaxEntries 1.3.6.1.4.1.52.4.1.2.7.1.7.1.2
Returns the maximum number of IP address entries supported by the IP Priority Queue application on this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

iPPQNumEntries 1.3.6.1.4.1.52.4.1.2.7.1.7.1.3
Get the number of IP address entries currently programmed in the ipPQAddressTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

iPPQAddAddress 1.3.6.1.4.1.52.4.1.2.7.1.7.1.4
Add an IP address to the ipPQAddressTable. Always read as a 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

iPPQDelAddress 1.3.6.1.4.1.52.4.1.2.7.1.7.1.5
Delete an IP address from the ipPQAddressTable. Always read as a 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipPQAddressTable 1.3.6.1.4.1.52.4.1.2.7.1.7.2
Table containing IP addresses, used in an IP Priority Queue Forwarding function.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpPQAddressEntry

ipPQAddressEntry 1.3.6.1.4.1.52.4.1.2.7.1.7.2.1
A description of a single entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpPQAddressEntry  

ipPQAddressId 1.3.6.1.4.1.52.4.1.2.7.1.7.2.1.1
A unique value identifying an element in a sequence of IP PQ address entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ipPQIPAddress 1.3.6.1.4.1.52.4.1.2.7.1.7.2.1.2
Returns an IP address associated with a specific entry in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ctWanHDSLPerformance15mTable 1.3.6.1.4.1.52.4.1.2.7.1.8.1
HDSL 15 minute performance table. This table provides the accumulated counts of errored seconds (ES) and unavailable seconds (UAS) for the HDSL line including the local, remote units and any doublers in between during a 15 minutes period for the last 24 hours. The table is indexed by the non-empty slot in the device and the 15-minute history slot within the last 24 hours period.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtWanHDSLPerformance15mEntry

ctWanHDSLPerformance15mEntry 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1
Entries in the 15 minute performance table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtWanHDSLPerformance15mEntry  

ctWanHDSLPerformance15mConnIndex 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.1
Identify the HDSL connection within the device, indexing from 1 to the maximum allowed number of HDSL connections in the device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPerformance15mSlotIndex 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.2
Define which 15-minute slot history of the HDSL within the 24 hour period. Indexing from 1 - 97 with the first index representing the current 15-minute history
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHLULoop1UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.3
Unavailable seconds (UAS) on LOOP 1 of the local line unit during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHLULoop1ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.4
Errored seconds (ES) on LOOP 1 of the local line unit during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHLULoop2UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.5
Unavailable seconds (UAS) on LOOP 2 of the local line unit during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHLULoop2ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.6
Errored seconds (ES) on LOOP 2 of the local line unit during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHRULoop1UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.7
Unavailable seconds (UAS) on LOOP 1 of the remote line unit during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHRULoop1ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.8
Errored seconds (ES) on LOOP 1 of the remote line unit during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHRULoop2UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.9
Unavailable seconds (UAS) on LOOP 2 of the remote line unit during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHRULoop2ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.10
Errored seconds (ES) on LOOP 2 of the remote line unit during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1NetworkLoop1UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.11
Unavailable seconds (UAS) on LOOP 1 of the first doubler unit's network side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1NetworkLoop1ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.12
Errored seconds (ES) on LOOP 1 of the first doubler unit's network side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1NetworkLoop2UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.13
Unavailable seconds (UAS) on LOOP 2 of the first doubler unit's network side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1NetworkLoop2ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.14
Errored seconds (ES) on LOOP 2 of the first doubler unit's network side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1CustomerLoop1UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.15
Unavailable seconds (UAS) on LOOP 1 of the first doubler unit's customer side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1CustomerLoop1ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.16
Errored seconds (ES) on LOOP 1 of the first doubler unit's customer side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1CustomerLoop2UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.17
Unavailable seconds (UAS) on LOOP 2 of the first doubler unit's customer side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1CustomerLoop2ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.18
Errored seconds (ES) on LOOP 2 of the first doubler unit's customer side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2NetworkLoop1UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.19
Unavailable seconds (UAS) on LOOP 1 of the second doubler unit's network side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2NetworkLoop1ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.20
Errored seconds (ES) on LOOP 2 of the second doubler unit's network side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2NetworkLoop2UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.21
Unavailable seconds (UAS) on LOOP 2 of the second doubler unit's network side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2NetworkLoop2ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.22
Errored seconds (ES) on LOOP 2 of the second doubler unit's network side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2CustomerLoop1UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.23
Unavailable seconds (UAS) on LOOP 1 of the second doubler unit's customer side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2CustomerLoop1ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.24
Errored seconds (ES) on LOOP 1 of the second doubler unit's customer side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2CustomerLoop2UAS15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.25
Unavailable seconds (UAS) on LOOP 2 of the second doubler unit's customer side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2CustomerLoop2ES15m 1.3.6.1.4.1.52.4.1.2.7.1.8.1.1.26
Errored seconds (ES) on LOOP 2 of the second doubler unit's customer side during the 15-minute period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPerformance24hTable 1.3.6.1.4.1.52.4.1.2.7.1.8.2
HDSL 24-hour performance table. This table provides the accumulated counts of errored seconds (ES) and unavailable seconds (UAS) for the HDSL line including the local, remote units and any doublers in between during a 24-hour period for the last 7 days. The table is indexed by the non-empty slot in the device and the 24-hour history slot within the last 7 days period.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtWanHDSLPerformance24hEntry

ctWanHDSLPerformance24hEntry 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1
Entries in the 24-hour ctWanHDSLPerformance table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtWanHDSLPerformance24hEntry  

ctWanHDSLPerformance24hConnIndex 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.1
Identify the HDSL connection within the device, indexing from 1 to the maximum allowed number of HDSL connections in the device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPerformance24hSlotIndex 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.2
Define which 24-hour slot history of the HDSL within the last 7 days period. Indexing from 1 - 8 with the first index representing the current 24 hour history
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHLULoop1UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.3
Unavailable seconds (UAS) on LOOP 1 of the local line unit during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHLULoop1ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.4
Errored seconds (ES) on LOOP 1 of the local line unit during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHLULoop2UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.5
Unavailable seconds (UAS) on LOOP 2 of the local line unit during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHLULoop2ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.6
Errored seconds (ES) on LOOP 2 of the local line unit during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHRULoop1UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.7
Unavailable seconds (UAS) on LOOP 1 of the remote line unit during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHRULoop1ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.8
Errored seconds (ES) on LOOP 1 of the remote line unit during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHRULoop2UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.9
Unavailable seconds (UAS) on LOOP 2 of the remote line unit during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHRULoop2ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.10
Errored seconds (ES) on LOOP 2 of the remote line unit during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1NetworkLoop1UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.11
Unavailable seconds (UAS) on LOOP 1 of the first doubler unit's network side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1NetworkLoop1ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.12
Errored seconds (ES) on LOOP 1 of the first doubler unit's network side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1NetworkLoop2UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.13
Unavailable seconds (UAS) on LOOP 2 of the first doubler unit's network side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1NetworkLoop2ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.14
Errored seconds (ES) on LOOP 2 of the first doubler unit's network side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1CustomerLoop1UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.15
Unavailable seconds (UAS) on LOOP 1 of the first doubler unit's customer side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1CustomerLoop1ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.16
Errored seconds (ES) on LOOP 1 of the first doubler unit's customer side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1CustomerLoop2UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.17
Unavailable seconds (UAS) on LOOP 2 of the first doubler unit's customer side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb1CustomerLoop2ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.18
Errored seconds (ES) on LOOP 2 of the first doubler unit's customer side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2NetworkLoop1UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.19
Unavailable seconds (UAS) on LOOP 1 of the second doubler unit's network side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2NetworkLoop1ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.20
Errored seconds (ES) on LOOP 1 of the second doubler unit's network side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2NetworkLoop2UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.21
Unavailable seconds (UAS) on LOOP 2 of the second doubler unit's network side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2NetworkLoop2ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.22
Errored seconds (ES) on LOOP 2 of the second doubler unit's network side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2CustomerLoop1UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.23
Unavailable seconds (UAS) on LOOP 1 of the second doubler unit's customer side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2CustomerLoop1ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.24
Errored seconds (ES) on LOOP 1 of the second doubler unit's customer side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2CustomerLoop2UAS24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.25
Unavailable seconds (UAS) on LOOP 2 of the second doubler unit's customer side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDb2CustomerLoop2ES24h 1.3.6.1.4.1.52.4.1.2.7.1.8.2.1.26
Errored seconds (ES) on LOOP 2 of the second doubler unit's customer side during the 24-hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLStatisticsTable 1.3.6.1.4.1.52.4.1.2.7.1.8.3
This table collects the statistics for the Signal noise ratio (SNR), and the pulse attenuation of the HDSL line, including the local, remote units and the doublers in between.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtWanHDSLStatisticsEntry

ctWanHDSLStatisticsEntry 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1
Entries of the HDSL statistics table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtWanHDSLStatisticsEntry  

ctWanHDSLStatisticsHLUConnIndex 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.1
Identify the HDSL connection occupied in the device, indexing from 1 to the maximum allowed connections in the device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHLULoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.2
Current SNR on LOOP 1 of the local line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowHLULoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.3
Lowest SNR on LOOP 1 of the local line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighHLULoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.4
Highest SNR on LOOP 1 of the local line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHLULoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.5
Current SNR on LOOP 2 of the local line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowHLULoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.6
Lowest SNR on LOOP 2 of the local line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighHLULoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.7
Highest SNR on LOOP 2 of the local line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationHLULoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.8
pulse Attenuation on LOOP 1 of the local line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationHLULoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.9
pulse Attenuation on LOOP 2 of the local line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLBitStat1HLU 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.10
A byte value which contains product specific information: bit 0 - System in AIS on the local line unit. 1 - System in AIS on the remote line unit. 2 - Channels are reversed on the remote line unit. 3 - Channels are reversed on the doubler 1. 4 - Channels are reversed on the doubler 2. 5 - Power is fed to the next unit on the local line unit. 6 - Power is fed to the next unit on the remote line unit. 7 - Smartloop is active on remote line unit. (HiGain only)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHRULoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.11
Current SNR on LOOP 1 of the remote line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowHRULoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.12
Lowest SNR on LOOP 1 of the remote line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighHRULoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.13
Highest SNR on LOOP 1 of the remote line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHRULoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.14
Current SNR on LOOP 2 of the remote line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowHRULoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.15
Lowest SNR on LOOP 2 of the remote line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighHRULoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.16
Highest SNR on LOOP 2 of the remote line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationHRULoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.17
pulse Attenuation on LOOP 1 of the remote line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationHRULoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.18
pulse Attenuation on LOOP 2 of the remote line unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLDs1FrameHRU 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.19
Byte value shows DS1 frame and code information for the remote line unit (HiGain only): bit 0:1 - 0 - frame format is SF. 1 - frame format is ESF. 2 - Frame format is unframed. 3 - no activity. bit 2:3 - reserved. bit 4 - 0 - line code is AMI 1 - line code is B8ZS. bit 5:7 - reserved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRDb1NetworkLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.20
Current SNR on LOOP 1 of doubler 1's network side
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowDb1NetworkLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.21
Lowest SNR on LOOP 1 of doubler 1's network side
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighDb1NetworkLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.22
Highest SNR on LOOP 1 of doubler 1's network side
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRDb1NetworkLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.23
Current SNR on LOOP 2 of doubler 1's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowDb1NetworkLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.24
Lowest SNR on LOOP 2 of doubler 1's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighDb1NetworkLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.25
Highest SNR on LOOP 2 of doubler 1's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRDb1CustomerLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.26
Current SNR on LOOP 1 of doubler 1's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowDb1CustomerLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.27
Lowest SNR on LOOP 1 of doubler 1's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighDb1CustomerLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.28
Highest SNR on LOOP 1 of doubler 1's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRDb1CustomerLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.29
Current SNR on LOOP 2 of doubler 1's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowDb1CustomerLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.30
Lowest SNR on LOOP 2 of doubler 1's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighDb1CustomerLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.31
Highest SNR on LOOP 2 of doubler 1's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationDb1NetworkLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.32
Pulse Attenuation on LOOP 1 of doubler 1's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationDb1NetworkLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.33
Pulse Attenuation on LOOP 2 of doubler 1's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationDb1CustomerLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.34
Pulse Attenuation on LOOP 1 of doubler 1's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationDb1CustomerLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.35
pulse Attenuation on LOOP 2 of doubler 1's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRDb2NetworkLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.36
Current SNR on LOOP 1 of doubler 2's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowDb2NetworkLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.37
Lowest SNR on LOOP 1 of doubler 2's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighDb2NetworkLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.38
Highest SNR on LOOP 1 of doubler 2's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRDb2NetworkLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.39
Current SNR on LOOP 2 of doubler 2's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowDb2NetworkLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.40
Lowest SNR on LOOP 2 of doubler 2's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighDb2NetworkLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.41
Highest SNR on LOOP 2 of doubler 2's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRDb2CustomerLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.42
Current SNR on LOOP 1 of doubler 2's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowDb2CustomerLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.43
Lowest SNR on LOOP 1 of doubler 2's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighDb2CustomerLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.44
Highest SNR on LOOP 1 of doubler 2's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRDb2CustomerLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.45
Current SNR on LOOP 2 of doubler 2's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRLowDb2CustomerLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.46
Lowest SNR on LOOP 2 of doubler 2's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLSNRHighDb2CustomerLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.47
Highest SNR on LOOP 2 of doubler 2's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationDb2NetworkLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.48
Pulse Attenuation on LOOP 1 of doubler 2's network side
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationDb2NetworkLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.49
Pulse Attenuation on LOOP 2 of doubler 2's network side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationDb2CustomerLoop1 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.50
pulse Attenuation on LOOP 1 of doubler 2's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLPulseAttenuationDb2CustomerLoop2 1.3.6.1.4.1.52.4.1.2.7.1.8.3.1.51
Pulse Attenuation on LOOP 2 of doubler 2's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLTestTable 1.3.6.1.4.1.52.4.1.2.7.1.8.4
Test result for the HDSL line, the current test results only apply to the local line unit.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtWanHDSLTestEntry

ctWanHDSLTestEntry 1.3.6.1.4.1.52.4.1.2.7.1.8.4.1
Entries of the HDSL test results table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtWanHDSLTestEntry  

ctWanHDSLTestHLUConnIndex 1.3.6.1.4.1.52.4.1.2.7.1.8.4.1.1
Identify the slot of the HDSL within the device that the user wants to conduct the line unit test. Slot number start from 1 to maximum slots available in the device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLTestMode 1.3.6.1.4.1.52.4.1.2.7.1.8.4.1.2
This object may only be successfully set on a master device. When this object is set, the local unit's test mode is defined by these values when set: 1 - Normal operation 3 - Self test mode 4 - PROM check test 5 - External RAM test 6 - DS1 loop test 7 - MUX-DMUX test 9 - Analog loopback mode 13 - Transceiver mode When getting this object, the value returned represents the last value this object had been set to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHLUTestResult 1.3.6.1.4.1.52.4.1.2.7.1.8.4.1.3
Test result for the local line unit (1 - test failed, 0 - success): bit 0 - 2180 DS1 frame sync test (HiGain only) 1 - 2180 DS1 data test (HiGain only) 2 - LIU DS1 frame sync test (HiGain only) 3 - LIU DS1 data test (HiGain only) 4 - External DS1 frame sync test (HiGain only) 5 - External DS1 data test. 6 - Mux sync test on HDSL LOOP 1 7 - Mux sync test on HDSL LOOP 2 8 - Reserved. 9 - Mux frame error test on HDSL LOOP 1 10 - Mux frame error test on HDSL LOOP 2 11 - Mux CRC test on HDSL LOOP 1 12 - Mux CRC test on HDSL LOOP 2 13 - Mux DL test on HDSL LOOP 1 14 - Mux DL test on HDSL LOOP 2 15 - Analog loopback test. 16 - Digital loop test. 17 - HGF HDSL loop test (HiGain only) 18 - HGF write/readback test (HiGain only) 19 - HGF poll lock test (HiGain only). 20 - HGF activity monitor test (HiGain only). 21 - HGF zeroes TX and detect test (HiGain only). 22 - HGF ones TX and detect test (HiGain only). 23 - Transceiver poll test on HDSL LOOP 1 24 - Transceiver poll test on HDSL LOOP 2 25 - PROM check test. 26 - External RAM test. 27 - Non-Volatile RAM test.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLHRUTestResult 1.3.6.1.4.1.52.4.1.2.7.1.8.4.1.4
Test results for the remote line unit, Bit definitions correspond to those defined for ctWanHDSLHLUTestResult.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlarmsTable 1.3.6.1.4.1.52.4.1.2.7.1.8.5
This table collects the existing alarms information for the HDSL line, including the local, remote line units and the doublers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtWanHDSLAlarmsEntry

ctWanHDSLAlarmsEntry 1.3.6.1.4.1.52.4.1.2.7.1.8.5.1
Entries for the ctWanHDSL alarms information
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtWanHDSLAlarmsEntry  

ctWanHDSLAlarmsHLUConnIndex 1.3.6.1.4.1.52.4.1.2.7.1.8.5.1.1
Identify which HDSL connection within the device that the user wants to retrieve the alarm information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlarmsBackplane 1.3.6.1.4.1.52.4.1.2.7.1.8.5.1.2
Specific information that's related to the HDSL alarms, each bit in the two bytes value has the following meaning if set: Bit 0 : Local Loss of Signal on DS1 line (HiGain only). 1 : Remote Loss of Signal on DS1 list (HiGain only). 2 - 7 : reserved. 8 : Loss of Sync word on LOOP 1 of the local line unit. 9 : Loss of Sync word on LOOP 2 of the local line unit. 10 : Loss of Sync word on LOOP 1 of the first doubler. 11 : Loss of sync word on LOOP 2 of the first doubler. 12 : Loss of Sync word on LOOP 1 of the second doubler. 13 : Loss of sync word on LOOP 2 of the second doubler.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlarmsES 1.3.6.1.4.1.52.4.1.2.7.1.8.5.1.3
A two bytes value for the Errored Second indication of the HDSL line unit, including local, remote line units and the doublers. each bit in the two bytes value has the following meaning if set: Bit 0 : Errored Second on LOOP 1 of local line unit. 1 : Errored Second on LOOP 2 of local line unit. 2 : Errored Second on LOOP 1 of remote line unit. 3 : Errored Second on LOOP 2 of remote line unit. 4 : Errored Second on LOOP 1 of local line unit's network side. 5 : Errored Second on LOOP 2 of local line unit's network side. 6 : Errored Second on LOOP 1 of local line unit's customer side. 7 : Errored Second on LOOP 2 of local line unit's customer side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlarmHistoryTable 1.3.6.1.4.1.52.4.1.2.7.1.8.6
HDSL Alarm History table. This table provides the accumulated counts of Errored Seconds (ES) and Loss of Sync words (LOS) as well as the time stamp of the above events occurred for both of the HDSL loops. The time stamps show the date in MMDDYYYYHHMM format.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtWanHDSLAlarmHistoryEntry

ctWanHDSLAlarmHistoryEntry 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1
Entries in the Alarm History table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtWanHDSLAlarmHistoryEntry  

ctWanHDSLAlarmHistoryConnIndex 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.1
Defines which HDSL connection's alarm history within the device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistLLOSFirst 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.2
Time stamp of the first time the DS1 Loss Of Signal (LOS) occurred on the local side of the HDSL.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistLLOSLast 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.3
Time stamp of the last time the DS1 Loss Of Signal (LOS) occurred on the local side of the HDSL.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistLLOSCurrent 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.4
Set if the DS1 Loss Of Signal (LOS) still occurred on the local side of the HDSL.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistLLOSCount 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.5
Number of times the DS1 Loss Of Signal (LOS) occurred since we last cleared the alarm history on the local side of the HDSL. (HiGain only)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistRLOSFirst 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.6
Time stamp of the first time the DS1 Loss Of Signal (LOS) occurred on the remote side of the HDSL. (HiGain only)
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistRLOSLast 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.7
Time stamp of the last time the DS1 Loss Of Signal (LOS) occurred on the remote side of the HDSL. (HiGain only)
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistRLOSCurrent 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.8
Set if the DS1 Loss Of Signal (LOS) still occurred on the remote site of the HDSL. (HiGain only)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistRLOSCount 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.9
Number of times the DS1 Loss Of Signal (LOS) occurred since we last cleared the alarm history on the remote site of the HDSL. (HiGain only)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistLOSW1First 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.10
Time stamp of the first time the Loss Of Sync Word (LOSW) occurred on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistLOSW1Last 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.11
Time stamp of the last time the Loss Of Sync Word (LOSW) occurred on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistLOSW1Current 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.12
Set if the Loss Of Sync Word (LOSW) still occurred on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistLOSW1Count 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.13
Number of times the Loss Of Sync Word (LOSW) occurred since we last cleared the history on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistLOSW2First 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.14
Time stamp of the first time the Loss Of Sync Word (LOSW) occurred on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistLOSW2Last 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.15
Time stamp of the last time the Loss Of Sync Word (LOSW) occurred on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistLOSW2Current 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.16
Set if the Loss Of Sync Word (LOSW) still occurred on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistLOSW2Count 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.17
Number of times the Loss Of Sync Word (LOSW) occurred since we last cleared the history on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistES1First 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.18
Time stamp of the first time the Errored Seconds (ES) occurred on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistES1Last 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.19
Time stamp of the last time the Errored Seconds (ES) occurred on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistES1Current 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.20
Set if the Errored Seconds (ES) still occurred on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistES1Count 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.21
Number of times the Errored Seconds (ES) occurred since we last cleared the alarm history on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistES2First 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.22
Time stamp of the first time the Errored Seconds (ES) occurred on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistES2Last 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.23
Time stamp of the last time the Errored Seconds (ES) occurred on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistES2Current 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.24
Set if the Errored Seconds (ES) still occurred on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistES2Count 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.25
Number of times the Errored Seconds (ES) occurred since we last cleared the history on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistMargin1First 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.26
Time stamp of the first time the alarms exceeded the Margin Threshold on LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistMargin1Last 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.27
Time stamp of the last time the alarms exceeded the Margin Threshold on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistMargin1Current 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.28
Set if the alarms still exceeded the Margin Threshold on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistMargin1Count 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.29
Number of times the alarm exceeded the Margin Threshold since we last cleared the alarm history on the LOOP 1 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistMargin2First 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.30
Time stamp of the first time the alarms exceeded the Margin Threshold on LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistMargin2Last 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.31
Time stamp of the last time the alarms exceeded the Margin Threshold on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistMargin2Current 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.32
Set if the alarms still exceeded the Margin Threshold on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistMargin2Count 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.33
Number of times the alarm exceeded the Margin Threshold since we last cleared the alarm history on the LOOP 2 of the HDSL link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLAlHistCleared 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.34
Time stamp of the time user requested to clear the alarm history.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

ctWanHDSLAlHistClearit 1.3.6.1.4.1.52.4.1.2.7.1.8.6.1.35
set to a 1 to clear the alarm history. A read of this value always returns a 1. NOTE: the setting of this object also causes the SNR low value, SNR high value, and the performance history to be reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctWanHDSLLoopbacksTable 1.3.6.1.4.1.52.4.1.2.7.1.8.7
HDSL Loopback table. This table provides the certain loopback settings for the HDSL link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtWanHDSLLoopbacksEntry

ctWanHDSLLoopbacksEntry 1.3.6.1.4.1.52.4.1.2.7.1.8.7.1
Entries in the HDSL Loopback table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtWanHDSLLoopbacksEntry  

ctWanHDSLLoopbacksHLUConnIndex 1.3.6.1.4.1.52.4.1.2.7.1.8.7.1.1
Identify the HDSL connection within the device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctWanHDSLLoopbacksAdminType 1.3.6.1.4.1.52.4.1.2.7.1.8.7.1.2
This is the requested loopback type for the HDSL. loopbacks setting: 1 : Smartjack - loopback to network at remote line unit. 2 : Loopback to network at local line unit. 3 : Loopback to network at remote line unit. 4 : Loopback to customer at local line unit. 5 : Loopback to customer at remote line unit. 6 : Loopback to customer at first doubler. 7 : Loopback to customer at second doubler. 8 : Loopback to network at first doubler. 9 : Loopback to network at second doubler. 10: No loopback (turn loopback off).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctWanHDSLLoopbacksOperType 1.3.6.1.4.1.52.4.1.2.7.1.8.7.1.3
This is the operational loopback type for the HDSL. loopbacks setting: 1 : Smartjack - loopback to network at remote line unit. 2 : Loopback to network at local line unit. 3 : Loopback to network at remote line unit. 4 : Loopback to customer at local line unit. 5 : Loopback to customer at remote line unit. 6 : Loopback to customer at first doubler. 7 : Loopback to customer at second doubler. 8 : Loopback to network at first doubler. 9 : Loopback to network at second doubler. 10: No loopback (turn loopback off).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER