DECHUB900-PTRM-MIB-V3-0

File: DECHUB900-PTRM-MIB-V3-0.mib (34476 bytes)

Imported modules

RFC1155-SMI RFC-1212

Imported symbols

enterprises OBJECT-TYPE

Defined Types

PtrmTrunkEntry  
SEQUENCE    
  ptrmTrunkType INTEGER
  ptrmTrunkOperStatus INTEGER
  ptrmTrunkAdminStatus INTEGER
  ptrmTrunkMedia INTEGER
  ptrmTrunkAutoWrapEnable INTEGER
  ptrmTrunkAutoPartitionStatus INTEGER
  ptrmTrunkDetectedSpeed INTEGER
  ptrmTrunkPhantomDrive INTEGER
  ptrmTrunkPhantomDetect INTEGER

PtrmLobeEntry  
SEQUENCE    
  ptrmLobeIndex INTEGER
  ptrmLobeOperStatus INTEGER
  ptrmLobeAdminStatus INTEGER
  ptrmLobeMedia INTEGER
  ptrmLobeAutoWrapEnable INTEGER
  ptrmLobeAutoPartitionStatus INTEGER
  ptrmLobeDetectedSpeed INTEGER
  ptrmLobePhantomDrive INTEGER
  ptrmLobePhantomDetect INTEGER

PtrmMacEntry  
SEQUENCE    
  ptrmMacIndex INTEGER
  ptrmMacRingInterface INTEGER
  ptrmMacAddress OCTET STRING
  ptrmMacPosition INTEGER

PtrmMultiBpPortEntry  
SEQUENCE    
  ptrmMultiBpPortIndex INTEGER
  ptrmMultiBpPortSpeed INTEGER
  ptrmMultiBpPortForceSpeed INTEGER

Defined Values

dec 1.3.6.1.4.1.36
OBJECT IDENTIFIER    

ema 1.3.6.1.4.1.36.2
OBJECT IDENTIFIER    

decMIBextension 1.3.6.1.4.1.36.2.18
OBJECT IDENTIFIER    

decHub900 1.3.6.1.4.1.36.2.18.11
OBJECT IDENTIFIER    

ptrm 1.3.6.1.4.1.36.2.18.11.3
OBJECT IDENTIFIER    

ptrmBase 1.3.6.1.4.1.36.2.18.11.3.1
OBJECT IDENTIFIER    

ptrmBaseForceSpeed 1.3.6.1.4.1.36.2.18.11.3.1.2
This object selects the speed at which to token ring linecard operates. When set to notForced(1), the linecard will not be forced. Based on the line-card its speed may change by a voting algorithm on its lobe ports or by console selection. Forcing the speed to 4 or 16 only applies when stand-alone; in a hub, the ring to which the module is forced determines the speed at which it operates. The value of this object is maintained across power cycles and resets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notForced(1), force-4Mbps(2), force-16Mbps(3)  

ptrmBaseSpeed 1.3.6.1.4.1.36.2.18.11.3.1.3
Indicates the speed at which the linecard is operating. Devices like the DECmau 900TL autobaud when they are not forced via ptrmBaseForceSpeed and if there are no stations plugged into the lobe ports. Devices like the DECmau 900TH (Dtmxm) have a default speed of 16Mbps which can also be changed via a console interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER autoBauding(1), speed-4Mbps(2), speed-16Mbps(3)  

ptrmBaseNumLobes 1.3.6.1.4.1.36.2.18.11.3.1.4
The number of end station lobes supported by this module. This is the number of rows in the ptrmLobeTable. This variable is zero for repeaters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..99  

ptrmTrunkTable 1.3.6.1.4.1.36.2.18.11.3.2
Defines a table with rows for each token ring connection not otherwise associated with an end-user 'lobe' port. The following rows are implemented: ptrmTrunkType Leaf VIDs Port ------------ ---------- ---- RingIn (1) 3.2.1.x.1 Copper Ring In RingOut (2) 3.2.1.x.2 Copper Ring Out HubA-1 (3) 3.2.1.x.3 Hub token ring A port 1 HubB-1 (4) 3.2.1.x.4 Hub token ring B port 1 FibreIn (5) 3.2.1.x.5 FibreRingIn FibreOut(6) 3.2.1.x.6 FibreRingOut HubA-2 (7) 3.2.1.x.3 Hub token ring A port 2 HubB-2 (8) 3.2.1.x.4 Hub token ring B port 2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PtrmTrunkEntry

ptrmTrunkEntry 1.3.6.1.4.1.36.2.18.11.3.2.1
A collection of trunk objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PtrmTrunkEntry  

ptrmTrunkType 1.3.6.1.4.1.36.2.18.11.3.2.1.1
Identifies a trunk (i.e. non-lobe) port. All token ring modules implement all four rows defined by the ptrmTrunkType values. If a module's configuration does not allow it to implement the particular trunk ptrmTrunkOperStatus is notPresent(3). For example, linecards in a hub do not have a RingIn or RingOut port and therefore contain the value notPreset(3) as the ptrmTrunkOperStatus for ringIn(1) and ringOut(2) rows of the trunk table. Linecards that do not have a fiber interface need not implement rows FiberIn(5) and FiberOut(6). NOTE - If a Trunk is notPresent, the rest of the values in this table are to be ignored.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER copperRingIn(1), copperRingOut(2), hubA(3), hubB(4), fiberRingIn(5), fiberRingOut(6)  

ptrmTrunkOperStatus 1.3.6.1.4.1.36.2.18.11.3.2.1.2
Indicates whether the trunk port is wrapped or inserted into the linecard's internal ring. If the trunk port is not implemented in the linecard's current configuration, then this is notPresent(3). If a trunk is notPresent(3), then the values read from all other columns of the row are undefined. If the port is enabled and an incompatible speed is detected, the value of this object is 'badSpeed(4)'. The trunk TCU is wrapped when in the badSpeed state. When there is a change in this object, a csnmp Trap is sent to the MAM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inserted(1), wrapped(2), notPresent(3), badSpeed(4)  

ptrmTrunkAdminStatus 1.3.6.1.4.1.36.2.18.11.3.2.1.3
Used to disable the trunk port of the linecard during operation. When disabled, the trunk port is forced to wrap. The value of this object is maintained across power cycles and resets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ptrmTrunkMedia 1.3.6.1.4.1.36.2.18.11.3.2.1.4
The media type of the trunk port. Different module types have different trunk connectors. If a module implements an STP/UTP switch, this variable indicates the setting of that switch. linecards feature Trunk Coupling Units (TCUs) on the module for their hub trunk connection, so they have 'media' type hubTCU(7). Repeaters have a direct connection to the hub backplane, so their hub trunk 'media' type is hubDirect(6).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER otherMedia(1), utpMedia(2), stpMedia(3), ibmMedia(4), fiberMedia(5), hubDirect(6), hubTCU(7)  

ptrmTrunkAutoWrapEnable 1.3.6.1.4.1.36.2.18.11.3.2.1.5
The value of the physical Auto Wrap Enable (AWE) switch for the trunk port. AWE is provided only for RingIn and RingOut trunks. AWE should be set ON for connection to DEChub token ring linecards. It should be set OFF when an IBM 8228 or equivalent 'dumb' linecard is connected. It MUST be physically switched to ON when no cable is inserted into the RI port, in order to cause RI to wrap. This value of this object is notApplicable(3) for hub trunks. The value of this object is maintained across power cycles and resets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), notApplicable(3)  

ptrmTrunkAutoPartitionStatus 1.3.6.1.4.1.36.2.18.11.3.2.1.6
Indicates whether the trunk port has been auto-partitioned. When autopartitioned(2) a trunk is automatically wrapped.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notAutoPartitioned(1), autoPartitioned(2)  

ptrmTrunkDetectedSpeed 1.3.6.1.4.1.36.2.18.11.3.2.1.7
Indicates the speed detected on the incoming data pair. invalid(1) indicates that a valid token ring speed was not detected. notApplicable(4) indicates that the trunk port does not implement speed detect. Hub trunks do not detect speed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), speed-4Mbps(2), speed-16Mbps(3), notApplicable(4)  

ptrmTrunkPhantomDrive 1.3.6.1.4.1.36.2.18.11.3.2.1.8
Indicates the state of the RingIn port's phantom current drive and return detect circuits. It is notApplicable(1) on all other trunk types. The noDrive(2) status indicates RingIn is not driving phantom current. driveReceive(3) is the normal case where an active linecard drives phantom current on RingIn and it is returned correctly from the upstream linecard. wireFault(4) indicates the linecard is driving phantom current but the current is not returned correctly, due to either an open or short circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(1), noDrive(2), driveReceive(3), wireFault(4)  

ptrmTrunkPhantomDetect 1.3.6.1.4.1.36.2.18.11.3.2.1.9
Indicates the state of the incoming phantom current detect circuit for the RingIn/RingOut Trunk. It is notApplicable(1) to all other trunk types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(1), noDetectPhantom(2), detectPhantom(3)  

ptrmLobeTable 1.3.6.1.4.1.36.2.18.11.3.3
A table with entries to manage individual end station lobe ports of the linecard.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PtrmLobeEntry

ptrmLobeEntry 1.3.6.1.4.1.36.2.18.11.3.3.1
A lobe entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PtrmLobeEntry  

ptrmLobeIndex 1.3.6.1.4.1.36.2.18.11.3.3.1.1
Port number for the lobe, as it appears externally to the user, i.e. 1 for the port labeled '1'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ptrmLobeOperStatus 1.3.6.1.4.1.36.2.18.11.3.3.1.2
Indicates whether the lobe port is wrapped or inserted into the linecard's internal ring. If the lobe port is not implemented in the linecard's current configuration the value of this object is notPresent(3). If a lobe is notPresent(3) then the values of other variables in the row are undefined. If the port is enabled and an incompatible speed is detected, this variable becomes 'badSpeed(4)'. The lobe TCU is wrapped when in the badSpeed state. When there is a change in this object, a CSNMP trap is sent to the MAM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inserted(1), wrapped(2), notPresent(3), badSpeed(4)  

ptrmLobeAdminStatus 1.3.6.1.4.1.36.2.18.11.3.3.1.3
Used to disable the lobe port during network troubleshooting. If set to disabled(2), the lobe port is forced to wrap. This object must be set to enabled(1) for normal operation. The value of this object is maintained across power cycles and resets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ptrmLobeMedia 1.3.6.1.4.1.36.2.18.11.3.3.1.4
The media type of the lobe port. Different module types have different lobe connectors. If a module implements an STP/UTP switch for lobes, this variable indicates the setting of that switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER otherMedia(1), utpMedia(2), stpMedia(3), ibmMedia(4), fiberMedia(5)  

ptrmLobeAutoWrapEnable 1.3.6.1.4.1.36.2.18.11.3.3.1.5
Software configuration variable set by network management. Auto Wrap Enabled (AWE) should be set on(1) for connection to end stations and the RingIn ports of DEC token ring products. It may be set off(2) for lobe connection to IBM 8228 or equivalent 'dumb' linecards which do not drive phantom current. The factory default is on(1). The value of this object is maintained across power cycles and resets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ptrmLobeAutoPartitionStatus 1.3.6.1.4.1.36.2.18.11.3.3.1.6
Indicates whether the lobe port has been auto-partitioned. When autoPartitioned(2), a lobe is automatically wrapped.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notAutoPartitioned(1), autoPartitioned(2)  

ptrmLobeDetectedSpeed 1.3.6.1.4.1.36.2.18.11.3.3.1.7
Indicates the speed detected on the incoming data pair. If invalid(1) a valid token ring speed was not detected. If notApplicable(4), the lobe port does not implement speed detect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), speed-4Mbps(2), speed-16Mbps(3), notApplicable(4)  

ptrmLobePhantomDrive 1.3.6.1.4.1.36.2.18.11.3.3.1.8
This variable is not applicable to lobe ports, and is defined only as a place holder for the corresponding trunk variable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(1)  

ptrmLobePhantomDetect 1.3.6.1.4.1.36.2.18.11.3.3.1.9
Indicates the state of the incoming phantom current detect circuit for the lobe port. Lobe ports are required to implement phantom detect circuitry; the notApplicable code is provided only for the corresponding trunk port variable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(1), noDetectPhantom(2), detectPhantom(3)  

ptrmMacTable 1.3.6.1.4.1.36.2.18.11.3.4
A table with entries. The table has 1 entry per MAC chip it contains.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PtrmMacEntry

ptrmMacEntry 1.3.6.1.4.1.36.2.18.11.3.4.1
An entry for the Mac .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PtrmMacEntry  

ptrmMacIndex 1.3.6.1.4.1.36.2.18.11.3.4.1.1
An index into the table. There is 1 entry in the table per MAC chip
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ptrmMacRingInterface 1.3.6.1.4.1.36.2.18.11.3.4.1.2
Indicates the Ring Interface number corresponding to this MAC. Typically single-ring devices will have only 1 Ring Interface. Devices like the Active Retimed concentartor which suppport multiple segements may have more than 1 ring interface. Note - the interface number must match that reported in the dot5.mib
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ptrmMacAddress 1.3.6.1.4.1.36.2.18.11.3.4.1.3
The Mac address in MSB form for this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

ptrmMacPosition 1.3.6.1.4.1.36.2.18.11.3.4.1.4
This is the position of the Mac Chip. For modules like the DTMXM, the position of the MAC is settable via software. It can be either before port 1 (MacForward) or after its last port (MacBackward) This makes it easy to partition the ports on its own ring for an accurate ring map. Modules that are end-stations and hence have no lobe ports may report Mac position as 1. if the Mac is in MacForward position the ptrmMacPosition should be reported as 255. For all other Ports, if the Mac is between port A and port B, the Mac postion should be reported as port A.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

ptrmMultiBp 1.3.6.1.4.1.36.2.18.11.3.5
OBJECT IDENTIFIER    

ptrmNumBackplanePorts 1.3.6.1.4.1.36.2.18.11.3.5.1
Number of physical TokenRing backplane ports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ptrmNumLobePorts 1.3.6.1.4.1.36.2.18.11.3.5.2
Number of lobe ports the linecard has
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ptrmMultiBpPortTable 1.3.6.1.4.1.36.2.18.11.3.5.3
This table MUST be supported by TR linecards like the MIPPY, which support multiple physical Token Ring backplane ports. The number of rows in ptrmMultiBpPortTable will be ptrmNumBackplanePorts The ptrmBase group does not have to supported in this configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PtrmMultiBpPortEntry

ptrmMultiBpPortEntry 1.3.6.1.4.1.36.2.18.11.3.5.3.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PtrmMultiBpPortEntry  

ptrmMultiBpPortIndex 1.3.6.1.4.1.36.2.18.11.3.5.3.1.1
Index into the table. Corresponds to backplane port number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ptrmMultiBpPortSpeed 1.3.6.1.4.1.36.2.18.11.3.5.3.1.2
Indicates the speed at which the backplane port is operating. The port MUST have a default speed of 4Mbps or 16Mbps to support plug and play operation
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER speed-4Mbps(2), speed-16Mbps(3)  

ptrmMultiBpPortForceSpeed 1.3.6.1.4.1.36.2.18.11.3.5.3.1.3
This is used only for STANDALONE operation. This object selects the speed at which to token ring port operates. The value of this object is maintained across power cycles and resets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notForced(1), force-4Mbps(2), force-16Mbps(3)