DES3326SR-L2MGMT-MIB

File: DES3326SR-L2MGMT-MIB.mib (101819 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SWPRIMGMT-MIB
RFC1213-MIB

Imported symbols

Counter32 Counter64 TimeTicks
NOTIFICATION-TYPE MODULE-IDENTITY OBJECT-TYPE
IpAddress Unsigned32 MacAddress
RowStatus des3326sr DisplayString

Defined Types

PortList  
OCTET STRING Size(0..127)    

VlanIndex  
Unsigned32    

VlanId  
INTEGER 1..4094    

SwDevInfoPowerEntry  
SEQUENCE    
  swDevInfoPowerUnitIndex INTEGER
  swDevInfoPowerID INTEGER
  swDevInfoPowerStatus INTEGER

SwL2PortInfoEntry  
SEQUENCE    
  swL2PortInfoPortIndex INTEGER
  swL2PortInfoUnitIndex INTEGER
  swL2PortInfoType INTEGER
  swL2PortInfoLinkStatus INTEGER
  swL2PortInfoNwayStatus INTEGER
  swL2PortInfoModuleType INTEGER

SwL2PortCtrlEntry  
SEQUENCE    
  swL2PortCtrlPortIndex INTEGER
  swL2PortCtrlUnitIndex INTEGER
  swL2PortCtrlAdminState INTEGER
  swL2PortCtrlNwayState INTEGER
  swL2PortCtrlFlowCtrlState INTEGER
  swL2PortCtrlLockState INTEGER
  swL2PortCtrlMACNotifyState INTEGER
  swL2PortCtrlMulticastfilter INTEGER

SwL2QOSBandwidthControlEntry  
SEQUENCE    
  swL2QOSBandwidthPortIndex INTEGER
  swL2QOSBandwidthRxRate INTEGER
  swL2QOSBandwidthTxRate INTEGER

SwL2QOSSchedulingEntry  
SEQUENCE    
  swL2QOSSchedulingClassIndex INTEGER
  swL2QOSSchedulingMaxPkts INTEGER
  swL2QOSSchedulingMaxLatency INTEGER

SwL2QOS8021pUserPriorityEntry  
SEQUENCE    
  swL2QOS8021pUserPriorityIndex INTEGER
  swL2QOS8021pUserPriorityClass INTEGER

SwL2QOS8021pDefaultPriorityEntry  
SEQUENCE    
  swL2QOS8021pDefaultPriorityIndex INTEGER
  swL2QOS8021pDefaultPriority INTEGER

SwL2TrunkCtrlEntry  
SEQUENCE    
  swL2TrunkIndex INTEGER
  swL2TrunkName DisplayString
  swL2TrunkMasterPort INTEGER
  swL2TrunkMember PortList
  swL2TrunkFloodingPort INTEGER
  swL2TrunkType INTEGER
  swL2TrunkState RowStatus

SwL2IGMPCtrlEntry  
SEQUENCE    
  swL2IGMPCtrlVid INTEGER
  swL2IGMPQueryInterval INTEGER
  swL2IGMPMaxResponseTime INTEGER
  swL2IGMPRobustness INTEGER
  swL2IGMPLastMemberQueryInterval INTEGER
  swL2IGMPHostTimeout INTEGER
  swL2IGMPRouteTimeout INTEGER
  swL2IGMPLeaveTimer INTEGER
  swL2IGMPQueryState INTEGER
  swL2IGMPCurrentState INTEGER
  swL2IGMPCtrlState INTEGER

SwL2IGMPQueryInfoEntry  
SEQUENCE    
  swL2IGMPInfoVid INTEGER
  swL2IGMPInfoQueryCount INTEGER
  swL2IGMPInfoTxQueryCount INTEGER

SwL2IGMPInfoEntry  
SEQUENCE    
  swL2IGMPVid INTEGER
  swL2IGMPGroupIpAddr IpAddress
  swL2IGMPMacAddr MacAddress
  swL2IGMPPortMap PortList
  swL2IGMPIpGroupReportCount INTEGER

SwL2TrafficCtrlEntry  
SEQUENCE    
  swL2TrafficCtrlGroupIndex INTEGER
  swL2TrafficCtrlUnitIndex INTEGER
  swL2TrafficCtrlBMStromthreshold INTEGER
  swL2TrafficCtrlBcastStromCtrl INTEGER
  swL2TrafficCtrlMcastStromCtrl INTEGER
  swL2TrafficCtrlDlfStromCtrl INTEGER

SwL2TrafficSegEntry  
SEQUENCE    
  swL2TrafficSegPort INTEGER
  swL2TrafficSegForwardPorts PortList

SwL2PortSecurityControlEntry  
SEQUENCE    
  swL2PortSecurityPortIndex INTEGER
  swL2PortSecurityMaxLernAddr INTEGER
  swL2PortSecurityMode INTEGER
  swL2PortSecurityAdmState INTEGER

Defined Values

swL2MgmtMIB 1.3.6.1.4.1.171.11.49.2.1.2
The Structure of Layer 2 Network Management Information for the proprietary enterprise.
MODULE-IDENTITY    

swL2DevMgmt 1.3.6.1.4.1.171.11.49.2.1.2.1
OBJECT IDENTIFIER    

swL2PortMgmt 1.3.6.1.4.1.171.11.49.2.1.2.4
OBJECT IDENTIFIER    

swL2QOSMgmt 1.3.6.1.4.1.171.11.49.2.1.2.6
OBJECT IDENTIFIER    

swL2TrunkMgmt 1.3.6.1.4.1.171.11.49.2.1.2.8
OBJECT IDENTIFIER    

swL2MirrorMgmt 1.3.6.1.4.1.171.11.49.2.1.2.9
OBJECT IDENTIFIER    

swL2IGMPMgmt 1.3.6.1.4.1.171.11.49.2.1.2.10
OBJECT IDENTIFIER    

swL2TrafficMgmt 1.3.6.1.4.1.171.11.49.2.1.2.12
OBJECT IDENTIFIER    

swL2TrafficSegMgmt 1.3.6.1.4.1.171.11.49.2.1.2.13
OBJECT IDENTIFIER    

swL2PortSecurityMgmt 1.3.6.1.4.1.171.11.49.2.1.2.14
OBJECT IDENTIFIER    

swL2MgmtMIBTraps 1.3.6.1.4.1.171.11.49.2.1.2.15
OBJECT IDENTIFIER    

swL2DevInfo 1.3.6.1.4.1.171.11.49.2.1.2.1.1
OBJECT IDENTIFIER    

swDevInfoSystemUpTime 1.3.6.1.4.1.171.11.49.2.1.2.1.1.1
The value of sysUpTime at the time the switch entered its current operational state. If the current state was entered prior to the last re-initialization, then this object contains a zero value. This value is in units of seconds.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

swDevInfoTotalNumOfPort 1.3.6.1.4.1.171.11.49.2.1.2.1.1.2
The number of ports within this switch. This value is the sum of the ports within this switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoNumOfPortInUse 1.3.6.1.4.1.171.11.49.2.1.2.1.1.3
The number of ports in this switch connected to the segment or the end stations.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoConsoleInUse 1.3.6.1.4.1.171.11.49.2.1.2.1.1.4
This usage indication of console system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), in-use(2), not-in-use(3)  

swDevInfoModuleType 1.3.6.1.4.1.171.11.49.2.1.2.1.1.5
This object indicates the module type of this port.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

swL2DevCtrlUpDownloadState 1.3.6.1.4.1.171.11.49.2.1.2.1.1.6
status of upload/download control. If the value is 'other', means never firmware updated since device started up.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), in-process(2), invalid-file(3), violation(4), file-not-found(5), disk-full(6), complete(7), time-out(8)  

swDevInfoSaveCfg 1.3.6.1.4.1.171.11.49.2.1.2.1.1.7
This object indicates the status of the device configuration. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. proceeding(2) - the device configuration is saving into the NV-RAM. ready(3) - the device configuration has been ready to save into NV-RAM. failed(4) - The processing of saving device configuration is failed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), proceeding(2), ready(3), failed(4)  

swDevInfoPowerTable 1.3.6.1.4.1.171.11.49.2.1.2.1.1.8
A list of temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwDevInfoPowerEntry

swDevInfoPowerEntry 1.3.6.1.4.1.171.11.49.2.1.2.1.1.8.1
A entry of Power information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwDevInfoPowerEntry  

swDevInfoPowerUnitIndex 1.3.6.1.4.1.171.11.49.2.1.2.1.1.8.1.1
Indicates ID of the unit in the System
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoPowerID 1.3.6.1.4.1.171.11.49.2.1.2.1.1.8.1.2
Indicates ID of the power
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoPowerStatus 1.3.6.1.4.1.171.11.49.2.1.2.1.1.8.1.3
Indicates status of the power
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(0), lowVoltage(1), overCurrent(2), working(3), fail(4), connect(5), disconnect(6)  

swL2DevCtrl 1.3.6.1.4.1.171.11.49.2.1.2.1.2
OBJECT IDENTIFIER    

swL2DevCtrlStpState 1.3.6.1.4.1.171.11.49.2.1.2.1.2.1
This object can be enabled or disabled spanning tree algorithm during runtime of the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlIGMPSnooping 1.3.6.1.4.1.171.11.49.2.1.2.1.2.2
This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlRmonState 1.3.6.1.4.1.171.11.49.2.1.2.1.2.3
This object can be enabled or disabled RMON.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlUpDownloadImageFileName 1.3.6.1.4.1.171.11.49.2.1.2.1.2.4
The name of the image file to be uploaded/Downloaded from the device to TFTP server when enabling image upload/download function (by writing swL2DevCtrlUpDownloadImage).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

swL2DevCtrlUpDownloadImageSourceAddr 1.3.6.1.4.1.171.11.49.2.1.2.1.2.5
The ip address where been uploaded/Downloaded image file.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2DevCtrlUpDownloadImage 1.3.6.1.4.1.171.11.49.2.1.2.1.2.6
Image file upload/download control. After setting, it will immediately invoke image upload/download function. While retrieving the value of this object, it always returns 'other' normally.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), upload(2), download(3)  

swL2DevCtrlSaveCfg 1.3.6.1.4.1.171.11.49.2.1.2.1.2.7
As the object is set to active, the current device configuration is save into to NV-RAM.If set to normal, do nothing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), active(2)  

swL2DevCtrlCleanAllStatisticCounter 1.3.6.1.4.1.171.11.49.2.1.2.1.2.8
As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), active(2)  

swL2DevCtrlVlanIdOfFDBTbl 1.3.6.1.4.1.171.11.49.2.1.2.1.2.9
Indicates the VLAN ID which the Dot1dTpFdbTable belongs to ; The default value is DEFAULT_VLAN_ID of system .
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

swL2MACNotifyState 1.3.6.1.4.1.171.11.49.2.1.2.1.2.10
This object can enabled or disabled MAC Notification.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2MACNotifyHistorySize 1.3.6.1.4.1.171.11.49.2.1.2.1.2.11
This object indicates the history size of variation MAC in address table. The default value is 1 .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..500  

swL2MACNotifyInterval 1.3.6.1.4.1.171.11.49.2.1.2.1.2.12
This object indicates the time interval in second for trigger the MAC notify message.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

swL2DevAlarm 1.3.6.1.4.1.171.11.49.2.1.2.1.3
OBJECT IDENTIFIER    

swL2DevAlarmNewRoot 1.3.6.1.4.1.171.11.49.2.1.2.1.3.1
When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevAlarmTopologyChange 1.3.6.1.4.1.171.11.49.2.1.2.1.3.2
This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevAlarmLinkChange 1.3.6.1.4.1.171.11.49.2.1.2.1.3.3
This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortInfoTable 1.3.6.1.4.1.171.11.49.2.1.2.4.1
A table that contains information about every port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortInfoEntry

swL2PortInfoEntry 1.3.6.1.4.1.171.11.49.2.1.2.4.1.1
A list of information for each port of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2PortInfoEntry  

swL2PortInfoPortIndex 1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortInfoUnitIndex 1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.2
Indicates ID of the unit in the device
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortInfoType 1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.3
This object indicates the connector type of this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER portType-100Base-TX(1), portType-100Base-FX(2), portType-100Base-FL(3), portType-1000Base-TX(4), portType-1000Base-SX(5), portType-1000Base-LX(6), portType-1000Base-SX-GBIC(7), portType-1000Base-LX-GBIC(8), portType-1000Base-TX-GBIC(9), portType-1000Base-1394(10), none(11)  

swL2PortInfoLinkStatus 1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.4
This object indicates the port link status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), link-pass(2), link-fail(3)  

swL2PortInfoNwayStatus 1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.5
This object indicates the port speed and duplex mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), auto(2), half-10Mbps(3), full-10Mbps(4), half-100Mbps(5), full-100Mbps(6), half-1Gigabps(7), full-1Gigabps(8)  

swL2PortInfoModuleType 1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.6
This object indicates the module type of this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), moduleType-COMBO(1), moduleType-1394(2), moduleType-1000T(3), moduleType-MGBIC(4), moduleType-1P-SC-SX(5), moduleType-2P-SC-SX(6), moduleType-1P-SC-LX(7), moduleType-2P-SC-LX(8), moduleType-1P-TX(9), moduleType-2P-TX(10), moduleType-1P-MTRJ-SX(11), moduleType-2P-MTRJ-SX(12), moduleType-1P-MTRJ-LX(13), moduleType-2P-MTRJ-LX(14), moduleType-1P-GBIC(15), moduleType-2P-GBIC(16), moduleType-1P-GBIC-1P-TX(17), moduleType-1P-GBIC-1P-STACK(18), moduleType-2P-STACK(19), moduleType-2P-100FX(20), moduleType-1P-100FX(21), moduleType-2P-100FX-NEW(22), moduleType-1P-100FL(23), moduleType-2P-100FL(24), moduleType-2P-100TX(25), moduleType-BaseModule-24PORT(26)  

swL2PortCtrlTable 1.3.6.1.4.1.171.11.49.2.1.2.4.2
A table that contains control information about every port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortCtrlEntry

swL2PortCtrlEntry 1.3.6.1.4.1.171.11.49.2.1.2.4.2.1
A list of control information for each port of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2PortCtrlEntry  

swL2PortCtrlPortIndex 1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortCtrlUnitIndex 1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.2
Indicates ID of the unit in the device
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortCtrlAdminState 1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.3
This object decide the port enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlNwayState 1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.4
Chose the port speed, duplex mode, and N-Way function mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6), nway-disabled-1Gigabps-Half(7), nway-disabled-1Gigabps-Full(8)  

swL2PortCtrlFlowCtrlState 1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.5
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlLockState 1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.6
This object decide the port is locked or not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlMACNotifyState 1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.7
This object decide the MAC notification is enable not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlMulticastfilter 1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.8
This object decide the multicast packets filtering mode on this port .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(0), forward-all-groups(1), forward-unregistered-groups(2), filter-unregistered-groups(3)  

swL2QOSBandwidthControlTable 1.3.6.1.4.1.171.11.49.2.1.2.6.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOSBandwidthControlEntry

swL2QOSBandwidthControlEntry 1.3.6.1.4.1.171.11.49.2.1.2.6.1.1
A list of information contained in swL2QOSBandwidthControlTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2QOSBandwidthControlEntry  

swL2QOSBandwidthPortIndex 1.3.6.1.4.1.171.11.49.2.1.2.6.1.1.1
Indicates the port .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..650  

swL2QOSBandwidthRxRate 1.3.6.1.4.1.171.11.49.2.1.2.6.1.1.2
Indicates RX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000  

swL2QOSBandwidthTxRate 1.3.6.1.4.1.171.11.49.2.1.2.6.1.1.3
Indicates TX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000  

swL2QOSSchedulingTable 1.3.6.1.4.1.171.11.49.2.1.2.6.2
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOSSchedulingEntry

swL2QOSSchedulingEntry 1.3.6.1.4.1.171.11.49.2.1.2.6.2.1
A list of information contained in swL2QOSSchedulingTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2QOSSchedulingEntry  

swL2QOSSchedulingClassIndex 1.3.6.1.4.1.171.11.49.2.1.2.6.2.1.1
Indicates the hardware queue number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..3  

swL2QOSSchedulingMaxPkts 1.3.6.1.4.1.171.11.49.2.1.2.6.2.1.2
Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 255 can be specified.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL2QOSSchedulingMaxLatency 1.3.6.1.4.1.171.11.49.2.1.2.6.2.1.3
Indicates the maximum amount of time the hardware priority queue will be allowed to transmit packets before allowing the next lowest priority queue to begin transmit its packets. A value between 0 and 255 can be specified- with this value multiplied by 16 ms to arrive at the total allowed time for queue to transmit packets. For example, a value of 3 specifies 3*16=48 ms. The queue will continue transmitting the last packet until it is finished when the max_latency timer expires.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL2QOS8021pUserPriorityTable 1.3.6.1.4.1.171.11.49.2.1.2.6.3
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOS8021pUserPriorityEntry

swL2QOS8021pUserPriorityEntry 1.3.6.1.4.1.171.11.49.2.1.2.6.3.1
A list of information contained in swL2QOS8021pUserPriorityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2QOS8021pUserPriorityEntry  

swL2QOS8021pUserPriorityIndex 1.3.6.1.4.1.171.11.49.2.1.2.6.3.1.1
The 802.1p user priority .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

swL2QOS8021pUserPriorityClass 1.3.6.1.4.1.171.11.49.2.1.2.6.3.1.2
The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..3  

swL2QOS8021pDefaultPriorityTable 1.3.6.1.4.1.171.11.49.2.1.2.6.4
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOS8021pDefaultPriorityEntry

swL2QOS8021pDefaultPriorityEntry 1.3.6.1.4.1.171.11.49.2.1.2.6.4.1
A list of information contained in swL2QOS8021pDefaultPriorityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2QOS8021pDefaultPriorityEntry  

swL2QOS8021pDefaultPriorityIndex 1.3.6.1.4.1.171.11.49.2.1.2.6.4.1.1
Indicates the port number .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..650  

swL2QOS8021pDefaultPriority 1.3.6.1.4.1.171.11.49.2.1.2.6.4.1.2
The priority value to assign to untagged packets received by the switch ports on the switch..
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

swL2TrunkMaxSupportedEntries 1.3.6.1.4.1.171.11.49.2.1.2.8.1
Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkCurrentNumEntries 1.3.6.1.4.1.171.11.49.2.1.2.8.2
Current actived number of entries in the trunk configuration table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkCtrlTable 1.3.6.1.4.1.171.11.49.2.1.2.8.3
This table specifys which ports group a set of ports(up to 8) into a single logical link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrunkCtrlEntry

swL2TrunkCtrlEntry 1.3.6.1.4.1.171.11.49.2.1.2.8.3.1
A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2TrunkCtrlEntry  

swL2TrunkIndex 1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.1
The index of logical port trunk. The trunk group number depend on the existence of unit and module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkName 1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.2
The name of logical port trunk.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..12)  

swL2TrunkMasterPort 1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.3
The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

swL2TrunkMember 1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.4
Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 8 for one trunks.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

swL2TrunkFloodingPort 1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.5
The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

swL2TrunkType 1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.6
This object indicated that type of the trunk group. static : is static trunk group lacp : is LACP trunk group .
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), static(2), lacp(3)  

swL2TrunkState 1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.7
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

swL2TrunkAlgorithm 1.3.6.1.4.1.171.11.49.2.1.2.8.4
This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), mac-source(2), mac-destination(3), mac-source-dest(4), ip-source(5), ip-destination(6), ip-source-dest(7)  

swL2MirrorLogicTargetPort 1.3.6.1.4.1.171.11.49.2.1.2.9.1
This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

swL2MirrorPortSourceIngress 1.3.6.1.4.1.171.11.49.2.1.2.9.2
The represent the ingress into the source port packet to sniffed.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2MirrorPortSourceEgress 1.3.6.1.4.1.171.11.49.2.1.2.9.3
The represent the egress from the source port packet to sniffed.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2MirrorPortState 1.3.6.1.4.1.171.11.49.2.1.2.9.4
This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - writing this value to the object, and then the corresponding entry will be removed from the table. enabled(3) - this entry is reside in the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPMaxSupportedVlans 1.3.6.1.4.1.171.11.49.2.1.2.10.1
Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPMaxIpGroupNumPerVlan 1.3.6.1.4.1.171.11.49.2.1.2.10.2
Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPCtrlTable 1.3.6.1.4.1.171.11.49.2.1.2.10.3
The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPCtrlEntry

swL2IGMPCtrlEntry 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1
The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPCtrlEntry  

swL2IGMPCtrlVid 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.1
This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPQueryInterval 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.2
The frequency at which IGMP Host-Query packets are transmitted on this switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

swL2IGMPMaxResponseTime 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.3
The maximum query response time on this switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..25  

swL2IGMPRobustness 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.4
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

swL2IGMPLastMemberQueryInterval 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.5
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

swL2IGMPHostTimeout 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.6
The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPRouteTimeout 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.7
The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPLeaveTimer 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.8
When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16711450  

swL2IGMPQueryState 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.9
This object decide the IGMP query enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPCurrentState 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.10
This object indicates the current IGMP query state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), querier(2), non-querier(3)  

swL2IGMPCtrlState 1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.11
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

swL2IGMPQueryInfoTable 1.3.6.1.4.1.171.11.49.2.1.2.10.4
The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPQueryInfoEntry

swL2IGMPQueryInfoEntry 1.3.6.1.4.1.171.11.49.2.1.2.10.4.1
Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPQueryInfoEntry  

swL2IGMPInfoVid 1.3.6.1.4.1.171.11.49.2.1.2.10.4.1.1
This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoQueryCount 1.3.6.1.4.1.171.11.49.2.1.2.10.4.1.2
This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoTxQueryCount 1.3.6.1.4.1.171.11.49.2.1.2.10.4.1.3
This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoTable 1.3.6.1.4.1.171.11.49.2.1.2.10.5
The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPInfoEntry

swL2IGMPInfoEntry 1.3.6.1.4.1.171.11.49.2.1.2.10.5.1
Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPInfoEntry  

swL2IGMPVid 1.3.6.1.4.1.171.11.49.2.1.2.10.5.1.1
This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPGroupIpAddr 1.3.6.1.4.1.171.11.49.2.1.2.10.5.1.2
This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL2IGMPMacAddr 1.3.6.1.4.1.171.11.49.2.1.2.10.5.1.3
This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

swL2IGMPPortMap 1.3.6.1.4.1.171.11.49.2.1.2.10.5.1.4
This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swL2IGMPIpGroupReportCount 1.3.6.1.4.1.171.11.49.2.1.2.10.5.1.5
This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficCtrlTable 1.3.6.1.4.1.171.11.49.2.1.2.12.1
This table specifys the storm traffic control configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrafficCtrlEntry

swL2TrafficCtrlEntry 1.3.6.1.4.1.171.11.49.2.1.2.12.1.1
A list of information specifies the storm traffic control configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2TrafficCtrlEntry  

swL2TrafficCtrlGroupIndex 1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.1
The index of logical port trunk. The trunk group number depend on the existence of unit and module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficCtrlUnitIndex 1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.2
Indicates ID of the unit in the device
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficCtrlBMStromthreshold 1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.3
This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl, swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlDlfStromCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured amount of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL2TrafficCtrlBcastStromCtrl 1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.4
This object indicates broadcast storm control function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficCtrlMcastStromCtrl 1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.5
This object indicates multicast storm control function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficCtrlDlfStromCtrl 1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.6
This object indicates destination lookup fail function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficSegTable 1.3.6.1.4.1.171.11.49.2.1.2.13.1
This table specifys the port just can forward traffic to the specific port list.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrafficSegEntry

swL2TrafficSegEntry 1.3.6.1.4.1.171.11.49.2.1.2.13.1.1
A list of information specifies the port with its traffic forward list.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2TrafficSegEntry  

swL2TrafficSegPort 1.3.6.1.4.1.171.11.49.2.1.2.13.1.1.1
The port number of the logical port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficSegForwardPorts 1.3.6.1.4.1.171.11.49.2.1.2.13.1.1.2
The port list that the specific port can forward traffic.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2PortSecurityControlTable 1.3.6.1.4.1.171.11.49.2.1.2.14.1
port security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as static entry. When the learned addresses number reach N, any coming packet with not learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortSecurityControlEntry

swL2PortSecurityControlEntry 1.3.6.1.4.1.171.11.49.2.1.2.14.1.1
A list of information contained in swL2PortSecurityControlTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2PortSecurityControlEntry  

swL2PortSecurityPortIndex 1.3.6.1.4.1.171.11.49.2.1.2.14.1.1.1
Indicates the secured port to lock address learning.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

swL2PortSecurityMaxLernAddr 1.3.6.1.4.1.171.11.49.2.1.2.14.1.1.2
Indicates allowable number of addresses to be learned at this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortSecurityMode 1.3.6.1.4.1.171.11.49.2.1.2.14.1.1.3
Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locked address is aged out, the number of address can be learned has to be increased by one. In deleteOnReset(4) mode - never age out the locked addresses unless restart the system to prevent from port movement or intrusion.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), permanent(2), deleteOnTimeout(3), deleteOnReset(4)  

swL2PortSecurityAdmState 1.3.6.1.4.1.171.11.49.2.1.2.14.1.1.4
Indicates administration state of locking address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), enable(2), disable(3)  

swL2MgmtMIBTrapPrefix 1.3.6.1.4.1.171.11.49.2.1.2.15.0
OBJECT IDENTIFIER    

swL2macNotification 1.3.6.1.4.1.171.11.49.2.1.2.15.0.3
This trap indicate the mac addresses variation in address table .
Status: current Access: read-write
NOTIFICATION-TYPE    

swL2porttypechgNotification 1.3.6.1.4.1.171.11.49.2.1.2.15.0.4
This trap indicate the port type change.
Status: current Access: read-write
NOTIFICATION-TYPE    

swPowerStatusChg 1.3.6.1.4.1.171.11.49.2.1.2.15.0.5
Power Status change notification.
Status: current Access: read-write
NOTIFICATION-TYPE    

swPowerFailure 1.3.6.1.4.1.171.11.49.2.1.2.15.0.6
Power Failure notification.
Status: current Access: read-write
NOTIFICATION-TYPE    

swPowerRecover 1.3.6.1.4.1.171.11.49.2.1.2.15.0.7
Power Recover notification.
Status: current Access: read-write
NOTIFICATION-TYPE    

swl2NotificationBidings 1.3.6.1.4.1.171.11.49.2.1.2.15.1
OBJECT IDENTIFIER    

swL2macNotifyInfo 1.3.6.1.4.1.171.11.49.2.1.2.15.1.1
This object indicates the last time reboot information.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..1024)